Post on 11-Jun-2018
transcript
One of the best ways to enhance the enjoyment of your new vehicle is toread this manual. In it, you will learn how to operate its driving controls andconvenience items. Afterwards, keep this owner’s manual in your vehicle soyou can refer to it at any time.
Several warranties protect your new vehicle. Read the warranty bookletthoroughly so you understand the coverages and are aware of your rightsand responsibilities.
As you read this manual, you willfind information that is preceded bya symbol. Thisinformation is intended to help youavoid damage to your vehicle, otherproperty, or the environment.
Maintaining your vehicle according to the Maintenance Minder shown inthe instrument panel helps to keep your driving trouble-free while itpreserves your investment. When your vehicle needs maintenance, keep inmind that your dealer’s staff is specially trained in servicing the manysystems unique to your vehicle. Your dealer is dedicated to your satisfactionand will be pleased to answer any questions and concerns.
Congratulations! Your selection of a 2013 Honda Insight was a wiseinvestment. It will give you years of driving pleasure.
Introduction
i
TM
12/07/13 16:36:24 31TM8630_002
Index
Book Table of Contents
Chapter Table of Contents
Navigation Key
Your Vehicle at a Glance
2013 InsightRevised 09/2013
Introduction
ii
12/07/13 16:36:31 31TM8630_003
2013 Insight
California Proposition 65 Warning
This product contains or emits chemicals known to the State of California to cause cancer and birthdefects or other reproductive harm.
Event Data Recorders
This data belongs to the vehicle owner and may not be accessed by anyone elseexcept as legally required or with the permission of the vehicle owner.
Service Diagnostic RecordersThis vehicle is equipped with service-related devices that record information about powertrain performance. The datacan be used to verify emissions law requirements and/or help technicians diagnose and solve service problems. It mayalso be combined with data from other sources for research purposes, but it remains confidential.
WARNING:
This vehicle is equipped with one or more devices commonly referred to as event data recorders. Thesedevices record front seat belt use, front passenger seat occupancy, airbag deployment data, and the failureof any airbag system component.
-
-
-
-
-
-
To help you make informeddecisions about safety, we haveprovided operating procedures andother information on labels and inthis manual. This information alertsyou to potential hazards that couldhurt you or others.
You will find this important safety information in a variety offorms, including:
preceded by a safety alert symbol and one ofthree signal words: , , or .These signal words mean:
such as Important Safety Reminders or ImportantSafety Precautions.
such as Driver and Passenger Safety.
This entire book is filled with important safety information please read
Your safety, and the safety ofothers, is very important.And operating this vehicle safelyis an important responsibility.
Of course, it is not practical orpossible to warn you about all thehazards associated with operating ormaintaining your vehicle. You mustuse your own good judgement.
on the vehicle.
how to use this vehicle correctly and safely.
Safety Messages
Safety Headings
Safety Section
Safety Labels
Instructions
A Few Words About Safety
DANGER WARNING CAUTION
iii
You WILL be KILLED or SERIOUSLYHURT if you don’t follow instructions.
You CAN be KILLED or SERIOUSLYHURT if you don’t follow instructions.
You CAN be HURT if you don’t followinstructions.
12/07/13 16:36:42 31TM8630_004
it carefully.
2013 Insight
(seat belts, SRS, and child protection)
(main controls)
(indicators, gauges, multi-information display, dashboard, and steering column)
(climate control, audio, steering wheel, security, cruise control, and other convenience items)
(fuel, vehicle break-in, and cargo loading)
(engine and transmission operation)
(minder, fluid checking, minor services, and vehicle storage)
(flat tire, jump starting, overheating, and fuses)
(vehicle specifications, tires, and emissions controls)
(warranty and contact information)
(how to order)
Contents
............................................................Driver and Passenger Safety . 5
................................................................................................................................................Index . I
Service Information Summary
...............................................................................................Your Vehicle at a Glance . 3
.......Instruments and Controls . 59
............Features . 161
.......................................................................Before Driving . 243
.........................................................................................Driving . 261
.................................................Maintenance . 297
........................................Taking Care of the Unexpected . 347
..............................................Technical Information . 377
..................Warranty and Customer Relations (U.S. and Canada only) . 393
..................................................................................Authorized Manuals (U.S. only) . 397
1
12/07/13 16:36:55 31TM8630_006
Owner's Identification Form
Index
Book Table of Contents
Chapter Table of Contents
Navigation Key
Your Vehicle at a Glance
2013 Insight
A summary of the information youneed when you pull up to the fuelpump.
How to order manuals and othertechnical literature.
A convenient reference to thesections in this manual.
A quick reference to the maincontrols in your vehicle.
What gasoline to use, how to break-in your new vehicle, and how to loadluggage and other cargo.
The proper way to start the engine,shift the transmission, and park.
A summary of the warrantiescovering your new vehicle, and howto contact us for any reason. Refer toyour warranty manual for detailedinformation.
The Maintenance Minder showsyou when you need to take yourvehicle to the dealer for maintenanceservice. There is also a list of thingsto check and instructions on how tocheck them.
ID numbers, dimensions, capacities,and technical information.
This section covers several problemsmotorists sometimes experience,and details how to handle them.
Important information about theproper use and care of your vehicle’sseat belts, an overview of thesupplemental restraint system, andvaluable information on how toprotect children with child restraints.
Explains the purpose of eachinstrument panel indicator and gauge,the multi-information display, andhow to use the controls on thedashboard and steering column.
How to operate the climate controlsystem, the audio system, and otherconvenience features.
Overview of Contents
Contents
Your Vehicle at a Glance
Driver and Passenger Safety
Instruments and Controls
Before Driving
Driving
Maintenance
Warranty and CustomerRelations(U.S. and Canada only)
Authorized Manuals(U.S. only)
Index
Service Information Summary
Technical Information
Taking Care of the Unexpected
Features
2
TM
12/07/13 16:37:13 31TM8630_007
2013 Insight
**
*
**
Refer to the navigation system manual.1 :2 :
If equippedCONTINUED
Your Vehicle at a Glance
3
MULTI-INFORMATIONDISPLAY(P.72)
(P.62)INSTRUMENT PANEL INDICATORSGAUGES
ECON BUTTON
DOOR LOCK TAB
POWER DOOR LOCKMASTER SWITCH
POWER WINDOWSWITCHES
PASSENGER’SFRONT AIRBAG(P.10)
AUTOMATICTRANSMISSION(CVT)
EX model with navigation system is shown.
MIRROR CONTROLS
(P.72, P.75)
HOOD RELEASE HANDLE
CLIMATE CONTROLSYSTEM
DRIVER’S FRONT AIRBAG(P.10)
NAVIGATION SYSTEMAUDIO SYSTEM
(P.147)
(P.127)
(P.133)
(P.133)
(P.149)
HAZARD WARNINGBUTTON(P.125)
USB ADAPTER CABLEPADDLE SHIFTERS
(P.168)
(P.162)
(P.271)
(P.197, P.205)(P.276)(P.248)
2
11
12/07/13 16:37:19 31TM8630_008
2013 Insight
***
*
*
*
*
*
*
*
*
*
*
Only on vehicles equipped with navigation system. Refer to the navigation system manual.
To use the horn, press the center pad of the steering wheel.1 :2 :3 :
If equipped
Your Vehicle at a Glance
4
MULTI-INFORMATION BUTTONS
HORN
(P.76)
STEERING WHEELADJUSTMENTS
WINDSHIELDWIPERS/WASHERS
INSTRUMENT PANELBRIGHTNESS CONTROL KNOB
(P.76)MULTI-INFORMATIONBUTTONS
KM/MILE CHANGE KNOB(P.73)
PASSENGER AIRBAGOFF INDICATOR(P.35)
REAR WINDOW DEFOGGER/HEATED MIRROR
EX model with navigation system is shown.
REMOTE AUDIOCONTROL BUTTONS
NAVIGATION SYSTEM VOICECONTROL BUTTONS
HEADLIGHTS/TURN SIGNALS(P.120)
VEHICLE STABILITYASSIST (VSA) OFFSWITCH
BLUETOOTH HANDSFREELINKSYSTEM VOICE CONTROLBUTTONS
(P.124) (P.119)
CRUISE CONTROL BUTTONS
NAVIGATION SYSTEM /AUDIO SYSTEM
(P.126, P.148)
ACCESSORY POWER SOCKET
AUXILIARY INPUT JACK(P.128)
(P.222)
(P.168)
(P.155)
(P.218)
(P.225)
(P.294)
(P.217)
2
1
2
2
2
3
2
2
3
2
12/07/13 16:37:27 31TM8630_009
2013 Insight
-
This section gives you importantinformation about how to protectyourself and your passengers. Itshows you how to use seat belts. Itexplains how your airbags work. Andit tells you how to properly restraininfants and children in your vehicle.
.........Important Safety Precautions . 6.......Your Vehicle’s Safety Features . 8
.......................................Seat Belts . 9.........................................Airbags . 10
.........Protecting Adults and Teens . 12.....1. Close and Lock the Doors . 12
...........2. Adjust the Front Seats . 14............3. Adjust the Seat-Backs . 15
...4. Adjust the Head Restraints . 165. Fasten and Position the
.............................Seat Belts . 176. Maintain a Proper Sitting
................................Position . 18.....Advice for Pregnant Women . 19...Additional Safety Precautions . 20
Additional Information About.......................Your Seat Belts . 21
..Seat Belt System Components . 21......................Lap/Shoulder Belt . 22
Automatic Seat Belt...............................Tensioners . 23
...............Seat Belt Maintenance . 24Additional Information About
...........................Your Airbags . 25......Airbag System Components . 25
How Your Front Airbags.........................................Work . 28
...How Your Side Airbags Work . 32How Your Side Curtain Airbags
.........................................Work . 33..How the SRS Indicator Works . 34
How the Side Airbag Off......................Indicator Works . 34
How the Passenger Airbag Off......................Indicator Works . 35
.............................Airbag Service . 36...Additional Safety Precautions . 37
Protecting Children General................................Guidelines . 38
All Children Must Be...............................Restrained . 38
All Children Should Sit in a.................................Back Seat . 39
The Passenger’s Front Airbag.........Can Pose Serious Risks . 39
If You Must Drive with Several...................................Children . 41
If a Child Requires Close..................................Attention . 41
...Additional Safety Precautions . 42Protecting Infants and Small
...................................Children . 43.......................Protecting Infants . 43
.........Protecting Small Children . 44.....................Selecting a Child Seat . 45....................Installing a Child Seat . 46
...............................With LATCH . 47.........With a Lap/Shoulder Belt . 49
..............................With a Tether . 51...........Protecting Larger Children . 52
...............Checking Seat Belt Fit . 52..................Using a Booster Seat . 53
When Can a Larger Child Sit in.........................................Front . 54
...Additional Safety Precautions . 55.............Carbon Monoxide Hazard . 56
...................................Safety Labels . 57
Driver and Passenger Safety
Driver
andP
assengerSafety
5
12/07/13 16:37:31 31TM8630_010
2013 Insight
-
You’ll find many safetyrecommendations throughout thissection, and throughout this manual.The recommendations on this pageare the ones we consider to be themost important.
While airbags can save lives, theycan cause serious or fatal injuries tooccupants who sit too close to them,or are not properly restrained.Infants, young children, and shortadults are at the greatest risk. Besure to follow all instructions andwarnings in this manual.
Alcohol and driving don’t mix. Evenone drink can reduce your ability torespond to changing conditions, andyour reaction time gets worse withevery additional drink. So don’t drinkand drive, and don’t let your friendsdrink and drive, either.
A seat belt is your best protection inall types of collisions. Airbags aredesigned to supplement seat belts,not replace them. So even thoughyour vehicle is equipped with airbags,make sure you and your passengersalways wear your seat belts, andwear them properly (see page ).
Children age 12 and under shouldride properly restrained in a backseat, not the front seat. Infants andsmall children should be restrainedin a child seat. Larger childrenshould use a booster seat and a lap/shoulder belt until they can use thebelt properly without a booster seat(see pages ).
17
38 55
Important Safety Precautions
Be Aware of Airbag Hazards
Don’t Drink and DriveRestrain All Children
Always Wear Your Seat Belt
6
12/07/13 16:37:38 31TM8630_011
Driver
andP
assengerSafety
TOC
2013 Insight
Engaging in mobile phoneconversation or other activities thatkeep you from paying close attentionto the road, other vehicles andpedestrians could lead to a crash.Remember, situations can changequickly, and only you can decidewhen it is safe to divert attentionaway from driving.
Excessive speed is a major factor incrash injuries and deaths. Generally,the higher the speed, the greater therisk, but serious injuries can alsooccur at lower speeds. Never drivefaster than is safe for currentconditions, regardless of themaximum speed posted.
Having a tire blowout or amechanical failure can be extremelyhazardous. To reduce the possibilityof such problems, check your tirepressures and condition frequently,and perform all regularly scheduledmaintenance (see page ).338
Pay Appropriate Attention to theTask of Driving Safely
Control Your Speed
Keep YourVehicle in Safe Condition
Important Safety Precautions
7
12/07/13 16:37:44 31TM8630_012
Driver
andP
assengerSafety
TOC
2013 Insight
Your vehicle is equipped with manyfeatures that work together toprotect you and your passengersduring a crash.
The following pages explain how youcan take an active role in protectingyourself and your passengers.
Some features do not require anyaction on your part. These include astrong steel framework that forms asafety cage around the passengercompartment, front and rear crushzones, a collapsible steering column,and tensioners that tighten the frontseat belts in a crash.
However, you and your passengerscan’t take full advantage of thesefeatures unless you remain sitting inthe correct position and
. In fact, some safetyfeatures can contribute to injuries ifthey are not used properly.
Your Vehicle’s Safety Features
always wearyour seat belts
8
(2)
(6)
(4)
(2)
(10)
(8)
(5)
(11)
(8)
(3)(9)
(1)
(10)
(7)
(7)
(9) (12)
(1) Safety Cage(2) Crush Zones(3) Seats and Seat-Backs(4) Head Restraints(5) Collapsible Steering Column(6) Seat Belts(7) Front Airbags(8) Side Airbags(9) Side Curtain Airbags(10) Door Locks(11) Seat Belt Tensioners(12) Occupant Position Detection
System (OPDS) Sensor
12/07/13 16:37:50 31TM8630_013
Driver
andP
assengerSafety
TOC
2013 Insight
----
Your vehicle is equipped with seatbelts in all seating positions.
Seat belts are the single mosteffective safety device for adults andlarger children. (Infants and smallerchildren must be properly restrainedin child seats.)
Not wearing a seat belt properlyincreases the chance of seriousinjury or death in a crash, eventhough your vehicle has airbags.
When properly worn, seat belts:
Keep you connected to the vehicleso you can take advantage of thevehicle’s built-in safety features.
Help keep you from being thrownagainst the inside of the vehicleand against other occupants.
Keep you from being thrown outof the vehicle.
Help keep you in a good positionshould the airbags ever deploy. Agood position reduces the risk ofinjury from an inflating airbag andallows you to get the bestadvantage from the airbag.
Of course, seat belts cannotcompletely protect you in everycrash. But in most cases, seat beltscan reduce your risk of seriousinjury.
Always wear your seat belt, andmake sure you wear it properly.
Your seat belt system also includesan indicator on the instrument paneland a beeper to remind you and yourpassengers to fasten your seat belts.
Help protect you in almost everytype of crash, including:
frontal impactsside impactsrear impactsrollovers
In addition, most states and allCanadian provinces and territoriesrequire you to wear seat belts.
Seat Belts
Why Wear Seat Belts
What You Should Do:
Your Vehicle’s Safety Features
9
Not wearing a seat belt properlyincreases the chance of seriousinjury or death in a crash, eventhough your vehicle has airbags.
Be sure you and yourpassengers always wear seatbelts and wear them properly.
12/07/13 16:38:01 31TM8630_014
Driver
andP
assengerSafety
TOC
2013 Insight
Your vehicle has a supplementalrestraint system (SRS) with frontairbags to help protect the heads andchests of the driver and a front seatpassenger during a moderate tosevere frontal collision (see page
for more information on howyour front airbags work).
Your vehicle also has side airbags tohelp protect the upper torso of thedriver or a front seat passengerduring a moderate to severe sideimpact (see page for moreinformation on how your side airbagswork).
In addition, your vehicle has sidecurtain airbags to help protect theheads of the driver, front passenger,and passengers in the outer rearseating positions during a moderateto severe side or front impact (seepage for more information on howyour side curtain airbags work).28
32
33
Airbags
Your Vehicle’s Safety Features
10
12/07/13 16:38:08 31TM8630_015
Driver
andP
assengerSafety
TOC
2013 Insight
The most important things you needto know about your airbags are:
They are designed to supplementthe seat belts.
To dotheir job, airbags must inflate withtremendous force. So whileairbags help save lives, they cancause minor injuries or moreserious or even fatal injuries ifoccupants are not properlyrestrained or sitting properly.
Always wearyour seat belt properly, and situpright and as far back from thesteering wheel as possible whileallowing full control of the vehicle. Afront passenger should move theirseat as far back from the dashboardas possible.
The rest of this section gives moredetailed information about how youcan maximize your safety.
Remember, however, that no safetysystem can prevent all injuries ordeaths that can occur in a severecrash, even when seat belts areproperly worn and the airbags deploy.
Airbags do not replace seat belts.
Airbags offer no protection in rearcollisions, or minor frontal or sidecollisions.
Airbags can pose hazards.
What you should do:
Your Vehicle’s Safety Features
11
12/07/13 16:38:14 31TM8630_016
Driver
andP
assengerSafety
TOC
2013 Insight
-See pages for importantguidelines on how to properlyprotect infants, small children, andlarger children who ride in yourvehicle.
The following pages provideinstructions on how to properlyprotect the driver, adult passengers,and teenage children who are largeenough and mature enough to driveor ride in the front.
Your vehicle has a door/hatch open indicator (red)
on the instrument panel to indicatewhen any door or the hatch is nottightly closed.
See page for how to lock thedoors, and page for how the door/hatch open indicator works.
Your vehicle also has a door andhatch open indicator on the multi-information display to indicate
hatch is not tightly closed.You will see the appropriateindicator(s) for each condition.
You will also hear a beep when youturn the ignition switch to the ON(II) position, and each time you openany door or the hatch with the key inthe ON (II) position.
The above illustration shows that alldoors and the hatch are open.
After everyone has entered thevehicle, be sure the doors and thehatch are closed and locked.
38 55
68133
Introduction Close and Lock the Doors1.
Protecting Adults and Teens
12
12/07/13 16:38:23 31TM8630_017
when a specific door or the
Driver
andP
assengerSafety
TOC
2013 Insight
Locking the doors reduces thechance of someone being thrown outof the vehicle during a crash, and ithelps prevent passengers fromaccidentally opening a door andfalling out.
Your vehicle has the auto doorlocking/unlocking feature. For moreinformation, see page .
Locking the doors and the hatch alsohelps prevent an outsider fromunexpectedly opening a door or thehatch when you come to a stop.
When one or more doors or thehatch are not tightly closed, thecorresponding indicator for eachcondition will come on.
The above example shows the frontright and rear left doors, and thehatch open.
When the hatch is not tightly closed,this indicator will come on. 108
Protecting Adults and Teens
13
12/07/13 16:38:29 31TM8630_018
Driver
andP
assengerSafety
TOC
2013 Insight
Adjust the driver’s seat as far to therear as possible while allowing you tomaintain full control of the vehicle.Have a front passenger adjust theirseat as far to the rear as possible.
If you sit too close to the steeringwheel or dashboard, you can beseriously injured by an inflating frontairbag, or by striking the steeringwheel or dashboard.
The National Highway Traffic SafetyAdministration and TransportCanada recommend that driversallow at least 10 inches (25 cm)between the center of the steeringwheel and the chest. In addition toadjusting the seat, you can adjust thesteering wheel up and down, and inand out (see page ).
If you cannot get far enough awayfrom the steering wheel and stillreach the controls, we recommendthat you investigate whether sometype of adaptive equipment may help.
Once a seat is adjusted correctly,rock it back and forth to make sure itis locked in position.
See page for how to adjust thefront seats.
128141
Adjust the Front Seats2.
Protecting Adults and Teens
14
Sitting too close to a frontairbag can result in seriousinjury or death if the frontairbags inflate.
Always sit as far back from thefront airbags as possible.
12/07/13 16:38:36 31TM8630_019
Driver
andP
assengerSafety
TOC
2013 Insight
Adjust the driver’s seat-back to acomfortable, upright position,leaving ample space between yourchest and the airbag cover in thecenter of the steering wheel.
Passengers with adjustable seat-backs should also adjust theirseat- back to a comfortable,upright position.
Reclining a seat-back so that theshoulder part of the belt no longerrests against the occupant’s chestreduces the protective capability ofthe belt. It also increases the chanceof sliding under the belt in a crashand being seriously injured. Thefarther a seat-back is reclined, thegreater the risk of injury.
See page for how to adjust theseat-backs.
141
Adjust the Seat-Backs3.
Protecting Adults and Teens
15
Reclining the seat-back too farcan result in serious injury ordeath in a crash.
Adjust the seat-back to anupright position, and sit wellback in the seat.
12/07/13 16:38:42 31TM8630_020
Driver
andP
assengerSafety
TOC
2013 Insight
Adjust the driver’s head restraintso the center of the back of yourhead rests against the center ofthe restraint.
Have passengers adjust their headrestraints properly as well. Tallerpersons should adjust their restraintas high as possible.
Properly adjusted head restraintswill help protect occupants fromwhiplash and other crash injuries.
See page for how to adjust thehead restraints and how the driver’sand front passenger’s active headrestraints work.
142
Adjust the Head Restraints4.
Protecting Adults and Teens
16
Improperly positioning headrestraints reduces theireffectiveness and you can beseriously injured in a crash.
Make sure head restraints arein place and positioned properlybefore driving.
12/07/13 16:38:48 31TM8630_021
Driver
andP
assengerSafety
TOC
2013 Insight
Position the lap part of the belt aslow as possible across your hips,then pull up on the shoulder part ofthe belt so the lap part fits snugly.This lets your strong pelvic bonestake the force of a crash and reducesthe chance of internal injuries.
Insert the latch plate into the buckle,then tug on the belt to make sure thebelt is securely latched. Check thatthe belt is not twisted, because atwisted belt can cause seriousinjuries in a crash.
If the seat belt touches or crossesyour neck, or if it crosses your arminstead of your shoulder, you need toadjust the seat belt anchor height.
If necessary, pull up on the belt againto remove any slack, then check thatthe belt rests across the center ofyour chest and over your shoulder.
This spreads the forces of a crashover the strongest bones in yourupper body.
CONTINUED
Fasten andPosition the Seat Belts
5.
Protecting Adults and Teens
17
Improperly positioning the seatbelts can cause serious injuryor death in a crash.
Make sure all seat belts areproperly positioned beforedriving.
12/07/13 16:38:54 31TM8630_022
Driver
andP
assengerSafety
TOC
2013 Insight
This could causevery serious injuries in a crash.
If a seat belt does not seem to workproperly, it may not protect theoccupant in a crash.
Using a seatbelt that is not working properly canresult in serious injury or death.Have your dealer check the belt assoon as possible.
See page for additionalinformation about your seat beltsand how to take care of them.
Sitting improperly can increase thechance of injury during a crash. Forexample, if an occupant slouches,lies down, turns sideways, sitsforward, leans forward or sideways,or puts one or both feet up, thechance of injury during a crash isgreatly increased.
The front seats have adjustableseat belt anchors. To adjust theheight of an anchor, squeeze thetwo release buttons, and slide theanchor up or down as needed (ithas four positions).
After all occupants have adjustedtheir seats and head restraints, andput on their seat belts, it is veryimportant that they continue to situpright, well back in their seats, withtheir feet on the floor, until thevehicle is safely parked and theengine is off.
21
Maintain a ProperSitting Position
6.Never place the shoulder portion of alap/shoulder belt under your arm orbehind your back.
No one should sit in a seat with aninoperative seat belt.
Protecting Adults and Teens
18
RELEASE BUTTONS
12/07/13 16:39:02 31TM8630_023
Driver
andP
assengerSafety
TOC
2013 Insight
If you are pregnant, the best way toprotect yourself and your unbornchild when driving or riding in avehicle is to always wear a seat belt,and keep the lap part of the belt aslow as possible across the hips.
When driving, remember to situpright and adjust the seat as farback as possible while allowing fullcontrol of the vehicle. When ridingas a front passenger, adjust the seatas far back as possible.
This will reduce the risk of injuriesto both you and your unborn childthat can be caused by a crash or aninflating front airbag.
Each time you have a checkup,ask your doctor if it’s okay foryou to drive.
In addition, an occupant who is out ofposition in the front seat can beseriously or fatally injured in a crashby striking interior parts of thevehicle or being struck by aninflating front airbag.
Advice for Pregnant Women
Protecting Adults and Teens
19
Sitting improperly or out ofposition can result in seriousinjury or death in a crash.
Always sit upright, well back inthe seat, with your feet on thefloor.
12/07/13 16:39:08 31TM8630_024
Driver
andP
assengerSafety
TOC
2013 Insight
Carrying hard or sharpobjects on your lap, or driving witha pipe or other sharp object inyour mouth, can result in injuriesif your front airbag inflates.
If they do, theycould be very seriously injured in acrash.
Devices intended to improveoccupant comfort or reposition theshoulder part of a seat belt canreduce the protective capability ofthe seat belt and increase thechance of serious injury in a crash.
Objects onthe covers marked ‘‘SRS AIRBAG’’could interfere with the properoperation of the airbags or bepropelled inside the vehicle andhurt someone if the airbags inflate.
If yourhands or arms are close to anairbag cover, they could be injuredif the airbag inflates.
If a side airbag or aside curtain airbag inflates, a cupholder or other hard objectattached on or near the door couldbe propelled inside the vehicle andhurt someone.
If they do, theycould be very seriously injured in
A passenger who is notwearing a seat belt during a crashor emergency stop can be thrownagainst the inside of the vehicle,against other occupants, or out ofthe vehicle.
Improperly replacingor covering front seat-back coverscan prevent your side airbags frominflating during a side impact.
Do not place hard or sharp objectsbetween yourself and a frontairbag.
Two people should never use thesame seat belt.
Do not put any accessories on seatbelts.
Do not attach or place objects onthe front airbag covers.
Keep your hands and arms awayfrom the airbag covers.
Do not attach hard objects on ornear a door.
Never let passengers ride in thecargo area or on top of a folded-down back seat.
Passengers should not stand up orchange seats while the vehicle ismoving.
Do not cover or replace front seat-back covers without consultingyour dealer.
Additional Safety Precautions
Protecting Adults and Teens
20
12/07/13 16:39:16 31TM8630_025
Driver
andP
assengerSafety
TOC
a crash.
2013 Insight
Your seat belt system includes lap/shoulder belts in all seating positions. The front seat belts arealso equipped with automatic seatbelt tensioners.
In addition to the seat belt reminderindicator in the instrument panel,you will also see a ‘‘FASTEN SEATBELT’’ or ‘‘FASTEN PASSENGERSEAT BELT’’ message. This remainsdisplayed if you ignore it and do notfasten the seat belt while driving.
If either the driver or a frontpassenger does not fasten their seatbelt while driving, the beeper willsound and the indicator will flashagain at regular intervals.
The seat belt system includes anindicator on the instrument paneland a beeper to remind you and your front passenger to fasten yourseat belts.
If a front passenger does not fastentheir seat belt, the indicator willcome on about 6 seconds after theignition switch is turned to the ON(II) position.
You will also see a ‘‘FASTEN SEATBELT’’ message on the multi-information display.
This system monitors the front seatbelts. If you turn the ignition switchto the ON (II) position before yourseat belt is fastened, the beeper willsound and the indicator will flash. Ifyour seat belt is not fastened beforethe beeper stops, the indicator willstop flashing but remain on.
When no one is sitting in the frontpassenger’s seat, or an infant orsmall child is riding there, theindicator may not come on and thebeeper may not sound.
CONTINUED
Seat Belt System Components Seat Belt Indicator
Additional Information About Your Seat Belts
21
12/07/13 16:39:24 31TM8630_026
Driver
andP
assengerSafety
TOC
2013 Insight
If the indicator comes on or thebeeper sounds when the driver’s seatbelt is latched and there is no frontseat passenger and no items on thefront seat, something may beinterfering with the monitoringsystem. Look for and remove:
Any items under the frontpassenger’s seat.
Any object(s) hanging on the seator in the seat-back pocket.
Any object on the floor that istouching the rear of the seat-back.
If no obstructions are found, haveyour vehicle checked by a dealer.
All seat belts have an emergencylocking retractor. In normal driving,the retractor lets you move freely inyour seat while it keeps sometension on the belt. During a collisionor sudden stop, the retractorautomatically locks the belt to helprestrain your body.
The lap/shoulder belt goes overyour shoulder, across your chest,and across your hips.
To fasten the belt, insert the latchplate into the buckle, then tug on thebelt to make sure the buckle islatched (see page for how toproperly position the belt).
To unlock the belt, press the redPRESS button on the buckle. Guidethe belt across your body so that itretracts completely. After exiting the vehicle, be sure the belt is outof the way and will not getclosed in the door.
The seat belts in all positions exceptthe driver’s have a lockable retractorthat must be activated to secure achild seat (see page ).
17
49
Additional Information About Your Seat Belts
Lap/Shoulder Belt
22
12/07/13 16:39:32 31TM8630_027
Driver
andP
assengerSafety
TOC
2013 Insight
For added protection, the front seatbelts are equipped with automaticseat belt tensioners. When activated,the tensioners immediately tightenthe belts to help hold the driver anda front passenger in position.
If the shoulder part of the belt ispulled all the way out, the lockableretractor will activate. The belt willretract, but it will not allow thepassenger to move freely.
To deactivate the lockableretractor, unlatch the buckleand let the seat belt fully retract.To refasten the seat belt, pull it outonly as far as needed.
The tensioners can be activatedduring a collision in which the frontairbags . In this case, theairbags would not be needed, but theadditional restraint could be helpful.
If the tensioner is activated, the SRSindicator comes on and the tensionermust be replaced.
do not deploy
Additional Information About Your Seat Belts
Automatic Seat Belt Tensioners
23
Allowing a child to play with aseat belt or wrap one aroundtheir neck can result in seriousinjury or death.
Instruct children not to play withany seat belt and make sureany unused seat belt a childcan reach is buckled, fullyretracted, and locked.
12/07/13 16:39:38 31TM8630_028
Driver
andP
assengerSafety
TOC
2013 Insight
For safety, you should check thecondition of your seat belts regularly.
Pull each belt out fully, and look forfrays, cuts, burns, and wear. Checkthat the latches work smoothly andthe belts retract easily. If a belt doesnot retract easily, cleaning the beltmay correct the problem (see page
). Any belt that is not in goodcondition or working properlywill not provide good protection and should be replaced as soon as possible.
Honda provides a limited warrantyon seat belts. See your
booklet
If a seat belt is worn during a crash,you should have your dealer inspectthe belt, and replace it if necessary.A belt that has been worn during acrash may not provide the same levelof protection in a subsequent crash.The dealer should also inspect theanchors for damage and replacethem if needed. If the automatic seatbelt tensioners activate during acrash, they must be replaced.331
HondaWarranty Information
Additional Information About Your Seat Belts
Seat Belt Maintenance
24
Not checking or maintainingseat belts can result in seriousinjury or death if the seat beltsdo not work properly whenneeded.
Check your seat belts regularlyand have any problemcorrected as soon as possible.
12/07/13 16:39:44 31TM8630_029
Driver
andP
assengerSafety
TOC
for details.
2013 Insight
CONTINUED
Airbag System Components
Additional Information About Your Airbags
25
(1)
(3)
(5)
(4)
(5)
(6)
(10)
(13)(9) (8)
(14)(2)
(16)
(4)
(15)
(16)(14)
(8)
(11)
(7)(12)
(1) Driver’s Front Airbag(2) Passenger’s Front Airbag(3) Control Unit(4) Front Seat Belt Tensioners(5) Side Airbags(6) Driver’s Seat Position Sensor(7) Front Passenger’s Weight Sensors
(12) Front Passenger’s Weight Sensors Control Unit/OPDS Sensors Control Unit
(13) SRS Indicator(14) Side Curtain Airbags(15) Safing Sensor(16) Side Impact Sensors (Second)
(8) Front Impact Sensors(9) Passenger Airbag Off Indicator(10) Side Impact Sensors (First)(11) Occupant Position Detection System (OPDS) Sensor
12/07/13 16:39:51 31TM8630_030
Driver
andP
assengerSafety
TOC
2013 Insight
Your Airbag System includes:
Two SRS (supplemental restraintsystem) front airbags. The driver’sairbag is stored in the center ofthe steering wheel; the frontpassenger’s airbag is stored in thedashboard. Both are marked ‘‘SRSAIRBAG’’ (see page ).
Two side airbags, one for thedriver and one for a frontpassenger. The airbags are storedin the outer edges of the seat-backs. Both are marked ‘‘SIDEAIRBAG’’ (see page ).
Two side curtain airbags, one foreach side of the vehicle. Theairbags are stored in the ceiling,above the side windows. Thefront and rear pillars aremarked ‘‘SIDE CURTAINAIRBAG’’ (see page ).
Automatic front seat belttensioners (see page ).
Sensors that can detect amoderate to severe front impact orside impact.
Sensors that can detect whether achild is in the passenger’s sideairbag path and signal the controlunit to turn the airbag off (seepage ).
Sensors that can detect whetherthe driver’s seat belt and the frontpassenger’s seat belt are latchedor unlatched (see page ).
A driver’s seat position sensorthat monitors the distance of theseat from the front airbag. If theseat is too far forward, theairbag will inflate with less force(see page ).
28
32
33
23
32
21
30
Additional Information About Your Airbags
26
12/07/13 16:39:58 31TM8630_031
Driver
andP
assengerSafety
TOC
2013 Insight
An indicator on the instrumentpanel that alerts you that thepassenger’s side airbag has beenturned off (see page ).
An indicator on the dashboard thatalerts you that the passenger’sfront airbag has been turned off(see page ).
Emergency backup power in caseyour vehicle’s electrical system isdisconnected in a crash.
Weight sensors that monitor theweight on the front passenger’sseat. If the weight is about 65lbs (29 kg) or less (the weightof an infant or small child), thepassenger’s front airbag will beturned off (see page ).
A sophisticated electronicsystem that continually monitors and records information aboutthe sensors, the control unit, theairbag activators, the seat belttensioners, and driver and frontpassenger seat belt usewhen the ignition switch is in theON (II) position.
An indicator on the instrumentpanel that alerts you to a possibleproblem with your airbag systemcomponents (see page ).
34
35
34
30
Additional Information About Your Airbags
27
12/07/13 16:40:04 31TM8630_032
Driver
andP
assengerSafety
TOC
2013 Insight
After inflating, the front airbagsimmediately deflate, so they won’tinterfere with the driver’s visibility,or the ability to steer or operateother controls.
During a frontal crash, your seat beltrestrains your lower body and torso,and the front airbag helps protectyour head and chest.
Although both airbags normallyinflate within a split second of eachother, it is possible for only oneairbag to deploy.
This can happen if the severity of acollision is at the margin, orthreshold, that determines whetheror not the airbags will deploy. Insuch cases, the seat belt will providesufficient protection, and thesupplemental protection offered bythe airbag would be minimal.
If you ever have a moderate tosevere frontal collision, sensors willdetect the vehicle’s rapiddeceleration.
If the rate of deceleration is highenough, the control unit will inflatethe driver’s and front passenger’sairbags, at the time and with theforce needed.
Only the driver’s airbag can deploy ifthere is no passenger in the frontseat, or if the advanced airbagsystem has turned the passenger’sairbag off (see page ).
The total time for inflation anddeflation is less than a second, sofast that most occupants are notaware that the airbags deployed untilthey see them lying in their laps.35
How Your Front Airbags Work
Additional Information About Your Airbags
28
12/07/13 16:40:12 31TM8630_033
Driver
andP
assengerSafety
TOC
2013 Insight
After a crash, you may see whatlooks like smoke. This is actuallypowder from the airbag’s surface.Although the powder is notharmful, people with respiratoryproblems may experience sometemporary discomfort. Ifthis occurs, get out of the vehicleas soon as it is safe to do so.
Your vehicle is equipped with dual-stage, multiple-threshold frontairbags (SRS). During a frontal crashsevere enough to cause one or bothfront airbags to deploy, the airbagscan inflate at different rates,depending on the severity of thecrash, whether or not the seat beltsare latched, and/or other factors.Front airbags are designed tosupplement the seat belts to helpreduce the likelihood of head andchest injuries in frontal crashes.
CONTINUED
Additional Information About Your Airbags
Dual-Stage, Multiple-ThresholdFront Airbags (SRS)
29
12/07/13 16:40:17 31TM8630_034
Driver
andP
assengerSafety
TOC
2013 Insight
The driver’s advanced front airbagsystem includes a seat positionsensor under the seat. If the seat istoo far forward, the airbag willinflate with less force, regardless ofthe severity of the impact.
If there is a problem with the sensor,the SRS indicator will come on, andthe airbag will inflate in the normalmanner regardless of the driver’sseating position.
The passenger’s advanced frontairbag system has weight sensorsunder the seat. Although Hondadoes not encourage carrying aninfant or small child in front, if thesensors detect the weight of aninfant or small child (up to about 65lbs or 29 kg), the system willautomatically turn the passenger’sfront airbag off.
Your front airbags are also advancedairbags. The main purpose of thisfeature is to help prevent airbag-caused injuries to short drivers andchildren or small-statured adults whoride in front.
For both advanced airbags to workproperly:
Occupants must sit upright andwear their seat belts properly.
Failure to follow these instructionscould damage the sensors or preventthem from working properly.
Do not spill any liquids on orunder the seats, cover the sensors,or put any objects or metal itemsunder the front seats.Objects placed or pushed underthe front passenger’s seat maycause the sensor to malfunction,increasing the risk of injury in acrash.
Advanced Airbags
Additional Information About Your Airbags
30
PASSENGER’SSEAT WEIGHT SENSORSDRIVER’S SEAT POSITION SENSOR
12/07/13 16:40:26 31TM8630_035
Driver
andP
assengerSafety
TOC
2013 Insight
Be aware that objects placed on thepassenger’s seat can also cause theairbag to be turned off.
When the passenger airbag getsturned off by the weight sensors, a‘‘passenger airbag off’’ indicator inthe center of the dashboard comeson (see page ).
If the weight sensors detect there isno passenger in the front seat, theairbag is automatically turned off.However, the passenger airbag offindicator in this situation will notcome on.
To ensure that the passenger’sadvanced front airbag system willwork properly,
This includes:
A rear passenger pushing orpulling on the back of the frontpassenger’s seat.
Moving the front seat forciblyback against cargo on the seat orfloor behind it.
Hanging heavy items on the frontpassenger seat, or placing heavyitems in the seat-back pocket.
Moving the front seat or seat-backforcibly back against the foldedrear seat.
Back seat passengers should notwedge objects or intentionallyforce their feet under the frontpassenger seat.
35
Additional Information About Your Airbags
do not do anythingthat would increase or decrease theweight on the front passenger’s seat.
31
12/07/13 16:40:33 31TM8630_036
Driver
andP
assengerSafety
TOC
2013 Insight
To get the best protection from theside airbags, front seat occupantsshould wear their seat belts and situpright and well back in their seats.
Your vehicle has a side airbag cutoffsystem designed primarily to protecta child riding in the frontpassenger’s seat.
Although Honda does notencourage children to ride in front,if the position sensors detect achild has leaned into the sideairbag’s deployment path, theairbag will shut off.
The side airbag may also shut off if ashort adult leans sideways, or alarger adult slouches and leanssideways into the airbag’sdeployment path.
Objects placed on the frontpassenger seat can also cause theside airbag to be shut off.
If you ever have a moderate tosevere side impact, sensors willdetect rapid acceleration and signalthe control unit to instantly inflateeither the driver’s or the passenger’sside airbag.
Only one airbag will deploy during aside impact. If the impact is on thepassenger’s side, the passenger’sside airbag may not deploy if there isno passenger.
How Your Side Airbags Work
Additional Information About Your Airbags
Side Airbag Cutoff System
32
12/07/13 16:40:41 31TM8630_037
Driver
andP
assengerSafety
TOC
2013 Insight
If the side airbag off indicator comeson (see page ), have thepassenger sit upright. Once thepassenger is out of the airbag’sdeployment path, the system willturn the airbag back on, and theindicator will go out.
There will be some delay betweenthe moment the passenger movesinto or out of the airbag deploymentpath and when the indicator comeson or goes off.
If the impact is on the passenger’sside, the passenger’s side curtainairbag will inflate even if there are nooccupants on that side of the vehicle.
A front seat passenger should notuse a cushion or another object as abackrest. It may prevent the cutoffsystem from working properly.
To get the best protection from theside curtain airbags, occupantsshould wear their seat belts and situpright and well back in their seats.
One or both side curtain airbags mayinflate in a moderate to severefrontal collision which causes thefront airbags to deploy.
In a moderate to severe sideimpact, sensors will detectrapid acceleration and signal thecontrol unit to instantly inflate theside curtain airbag.
34
Additional Information About Your Airbags
How YourSide Curtain Airbags Work
33
SIDE CURTAIN AIRBAG
12/07/13 16:40:48 31TM8630_038
Driver
andP
assengerSafety
TOC
2013 Insight
If the indicator comes on at anyother time, or does not come on at all,you should have the system checkedby your dealer. For example:
When you turn the ignition switch tothe ON (II) position, this indicatorcomes on for several seconds thengoes off. This tells you the system isworking properly.
If the indicator comes on orflashes on and off while you drive.
If the indicator stays on after theengine starts.
If the SRS indicator does not comeon after you turn the ignitionswitch to the ON (II) position.
This indicator alerts you that thepassenger’s side airbag has beenautomatically shut off. It doesmean there is a problem with yourside airbags.
When you turn the ignition switch tothe ON (II) position, the indicatorshould come on for several secondsand then go off (see page ). If
You will also see a ‘‘CHECKAIRBAG SYSTEM’’ message on themulti-information display.
You will also see a ‘‘PASSENGERSIDE AIRBAG OFF’’ message on themulti-information display.
The SRS indicator alerts you to apotential problem with your airbagsystem components.
If you see any of these indications,the airbag system components may not work properly when you need them.
65
Additional Information About Your Airbags
How the SRS IndicatorWorks
How the SideAirbag OffIndicator Works
not
34
U.S. Canada
Ignoring the SRS indicator canresult in serious injury or deathif the airbag systems ortensioners do not work properly.
Have your vehicle checked by adealer as soon as possible ifthe SRS indicator alerts you toa possible problem.
12/07/13 16:41:01 31TM8630_039
Driver
andP
assengerSafety
TOC
it doesn’t come on, stays on, orcomes on while driving without apassenger in the front seat, have thesystem checked.
2013 Insight
This indicator alerts you that thepassenger’s front airbag has beenshut off because weight sensorsdetect about 65 lbs (29 kg) or less(the weight of an infant or smallchild) on the front passenger’s seat.It does there is a problemwith the airbag.
The passenger airbag off indicatormay come on and off repeatedly ifthe total weight on the seat is nearthe airbag cutoff threshold.
If an adult or teenage passenger isriding in front, move the seat as farto the rear as possible, and have thepassenger sit upright and wear theseat belt properly.
Be aware that objects placed on thefront seat can cause the indicator tocome on.
If no weight is detected on the frontseat, the airbag will be automaticallyshut off. However, the indicator willnot come on.
CONTINUED
Additional Information About Your Airbags
How the Passenger Airbag OffIndicator Works
not mean
35
PASSENGER AIRBAG OFF INDICATOR
PASSENGER AIRBAG OFF INDICATOR
Canada
U.S.
On vehicle with navigation system
On vehicle without navigation system
Canada
U.S.
12/07/13 16:41:09 31TM8630_040
Driver
andP
assengerSafety
TOC
2013 Insight
Take your vehicle to anauthorized dealer as soon aspossible. If you ignore thisindication, your airbags may notoperate properly.
Even if yourairbags do not inflate, your dealershould inspect the driver’s seatposition sensor, the frontpassenger’s weight sensors, thefront seat belt tensioners, and allseat belts and their anchors wornduring a crash to make sure theyare operating properly.
Your airbag systems are virtuallymaintenance free, and there are noparts you can safely service.However, you must have yourvehicle serviced if:
Any airbagthat has deployed must bereplaced along with the controlunit and other related parts. Anyseat belt tensioner that activatesmust also be replaced.
If no obstructions are found, haveyour vehicle checked by a dealer assoon as possible.
If the indicator comes on with nofront seat passenger and no objectson the seat, or with an adult ridingthere, something may be interferingwith the weight sensors. Look forand remove:
Any items under the frontpassenger’s seat.
Any object(s) hanging on the seator in the seat-back pocket.
Any object on the floor that istouching the rear of the seat-back.
Do not try to remove or replaceany airbag by yourself. This mustbe done by an authorized dealer ora knowledgeable body shop.
We recommend against the useof salvaged airbag systemcomponents, including theairbag, tensioners, sensors,and control unit.
Additional Information About Your Airbags
The SRS indicator alerts you to aproblem.
If your vehicle has a moderate tosevere impact.
An airbag ever inflates.
Airbag Service
36
12/07/13 16:41:19 31TM8630_041
Driver
andP
assengerSafety
TOC
2013 Insight
If water oranother liquid soaks into a seat-back, it can prevent the sideairbag cutoff system from working properly.
Tampering could causethe airbags to deploy, possiblycausing very serious injury.
Together, airbags andseat belts provide the bestprotection.
This could make thedriver’s seat position sensor or thefront passenger’s weight sensorsineffective. If it is necessary toremove or modify a front seat toaccommodate a person withdisabilities, first contact HondaAutomobile Customer Service at(800) 999-1009 in the US, orHonda Customer Relations at
Additional Information About Your Airbags
Do not expose the front passenger’sseat-back to liquid.
Do not tamper with airbagcomponents or wiring for anyreason.
Do not attempt to deactivate yourairbags.
Do not remove or modify a frontseat without consulting yourdealer.
Additional Safety Precautions
37
12/07/13 16:41:24 31TM8630_042
Driver
andP
assengerSafety
TOC
1-888-9-HONDA-9 in Canada.
2013 Insight
--
-
Children depend on adults to protectthem. However, despite their bestintentions, many adults do not knowhow to protect childpassengers.
If you have children, or everneed to drive with a child in yourvehicle, be sure to read this section. It begins with importantgeneral guidelines, then presents special information for infants,small children, and larger children.
(see pages ).(see pages ).
Each year, many children areinjured or killed in vehiclecrashes because they are eitherunrestrained or not properlyrestrained. In fact, vehicle collisions are the number one cause of thedeath of children age 12 and under.
To reduce the number of childdeaths and injuries, every state,Canadian province and territoryrequires that infants and children beproperly restrained when they ride ina vehicle.
43 5152 55
properly
All Children Must Be Restrained
Larger children must be restrainedwith a lap/shoulder belt and ride ona booster seat until the seat belt f itsthem properly
Infants and small children must berestrained in an approved child seatthat is properly secured to thevehicle
Protecting Children General Guidelines
38
Children who are unrestrainedor improperly restrained can beseriously injured or killed in acrash.
Any child too small for a seatbelt should be properlyrestrained in a child seat. Alarger child should be properlyrestrained with a seat belt anduse a booster seat if necessary.
12/07/13 16:41:31 31TM8630_043
Driver
andP
assengerSafety
TOC
2013 Insight
-
According to crash statistics,children of all ages and sizes aresafer when they are restrained in aback seat.
Whenever possible,larger children should sit in the backseat, on a booster seat if needed, andbe properly restrained with a seatbelt. (See page for importantinformation about protecting
Front airbags have been designed tohelp protect adults in a moderate tosevere frontal collision. To do this,the passenger’s front airbag is quitelarge, and it can inflate with enoughforce to cause very serious injuries.
If the vehicle seat istoo far forward, or the child’s head isthrown forward during a collision, aninflating front airbag can strike thechild with enough force to kill orvery seriously injure a small child.
The National Highway Traffic SafetyAdministration and TransportCanada recommend that all childrenaged 12 and under be properlyrestrained in a back seat. Somestates have laws restricting wherechildren may ride.
Children who ride in back are lesslikely to be injured by strikinginterior vehicle parts during acollision or hard braking. Also,children cannot be injured by aninflating front airbag when they ridein the back.
Even though your vehicle has anadvanced front airbag system thatautomatically turns the passenger’sfront airbag off under certaincircumstances (see page ), pleasefollow these guidelines:
Ifthe airbag inflates, it can hit the
35
52
CONTINUED
All Children Should Sit in a Back Seat
The Passenger’s Front AirbagCan Pose Serious Risks
Protecting Children General Guidelines
Small Children
Larger ChildrenChildren who have outgrown childseats are also at risk of being injuredor killed by an inflating passenger’sfront airbag.
Placing a forward-facing child seat inthe front seat of a vehicle equippedwith a passenger’s front airbag canbe hazardous.
Never put a rear-facing child seat inthe front seat of a vehicle equippedwith a passenger’s front airbag.
Infants
39
12/07/13 16:41:41 31TM8630_044
Driver
andP
assengerSafety
TOC
back of the child seat with enoughforce to kill or very seriously injurean infant.
larger children.)
2013 Insight
-
To remind you of the passenger’sfront airbag hazards, and thatchildren must be properly restrainedin a back seat, your vehicle haswarning labels on the dashboard(U.S. models) and on the front visors.Please read and follow theinstructions on these labels.
Canadian Models
U.S. Models
Protecting Children General Guidelines
40
SUN VISORS DASHBOARD
SUN VISORS
12/07/13 16:41:53 31TM8630_045
Driver
andP
assengerSafety
TOC
2013 Insight
-
Many parents say they prefer to
Placing a child in the front seatexposes the child to hazards in afrontal collision, and paying closeattention to a child distracts thedriver from the important tasks ofdriving, placing both of you at risk.
Your vehicle has a back seat wherechildren can be properly restrained.If you ever have to carry a group ofchildren, and a child must ride infront:
Place the largest child in the frontseat, provided the child is largeenough to wear the lap/shoulderbelt properly (see page ).
Move the vehicle seat as far to therear as possible (see page ).
Have the child sit upright and wellback in the seat (see page ).
Make sure the seat belt is properlypositioned and secured (seepage ).
If a child requires close physicalattention or frequent visual contact,we strongly recommend that anotheradult ride with the child in the backseat. The back seat is far safer for achild than the front.
52
18
17
141
If You Must Drive with Several Children
If a Child Requires
Protecting Children General Guidelines
41
12/07/13 16:42:01 31TM8630_046
Driver
andP
assengerSafety
TOCClose Attention
put an infant or a small child in thefront passenger seat so they canwatch the child, or because thechild requires attention.
2013 Insight
-
If they do, theycould be very seriously injured in
If you are not wearing aseat belt in a crash, you could bethrown forward and crush thechild against the dashboard or aseat-back. If you are wearing aseat belt, the child can be tornfrom your arms and be seriouslyhurt or killed.
During a crash, thebelt could press deep into the childand cause serious or fatal injuries.
This can preventchildren from accidentally fallingout (see page ).
If a child wraps a looseseat belt around their neck, theycan be seriously or fatally injured.(See pages and for how toactivate and deactivate thelockable retractor.)
Leaving children withoutadult supervision is illegal in moststates, Canadian provinces andterritories, and can be veryhazardous.
For example, infants and smallchildren left in a vehicle on a hotday can die from heatstroke. Achild left alone with the key in theignition switch can accidentally setthe vehicle in motion, possiblyinjuring themselves or others.
Childrenwho play in vehicles canaccidentally get trapped inside thevehicle. Teach your children not toplay in or around vehicles.
Even very youngchildren learn how to unlockvehicle doors, turn on theignition switch, and open thehatch, which can lead to accidental injury or death.
49 50
134
Additional Safety Precautions
Never let two children use thesame seat belt.
Never hold an infant or child onyour lap.
Never put a seat belt over yourselfand a child.
Use the childproof door locks toprevent children from opening therear doors.
Make sure any unused seat beltthat a child can reach is buckled,the lockable retractor is activated,and the belt is fully retracted andlocked.
Do not leave children alone in avehicle.
Lock all doors and the hatch whenyour vehicle is not in use.
Keep vehicle keys and remotetransmitters out of the reach ofchildren.
Protecting Children General Guidelines
42
12/07/13 16:42:09 31TM8630_047
Driver
andP
assengerSafety
TOC
a crash.
2013 Insight
When properly installed, a rear-facing child seat may prevent thedriver or a front passenger frommoving their seat as far back asrecommended, or from locking theirseat-back in the desired position.
Two types of seats may be used: aseat designed exclusively for infants,or a convertible seat used in the rear-facing, reclining mode.
If placedfacing forward, an infant could bevery seriously injured during afrontal collision.
A rear-facing child seat can be placedin any seating position in the backseat, but not in the front.
If the passenger’s front airbaginflates, it can hit the back of thechild seat with enough force to kill orseriously injure an infant.
An infant must be properlyrestrained in a rear-facing, recliningchild seat until the child reaches theseat maker’s weight or height limitfor the seat, and the child is at leastone year old.
Only a rear-facing child seat providesproper support for a baby’s head,neck, and back.
It could also interfere with properoperation of the passenger’sadvanced front airbag system.
CONTINUED
Protecting Infants
Child Seat Type
Do not put a rear-facing child seat ina forward-facing position.
Never put \
front seat.
Rear-facing Child Seat Placement
Protecting Infants and Small Children
43
12/07/13 16:42:19 31TM8630_048
Driver
andP
assengerSafety
TOC
a rear-facing child seat in the
2013 Insight
In any of these situations, westrongly recommend that you installthe child seat directly behind thefront passenger’s seat, move the seatas far forward as needed, and leave itunoccupied. Or, you may wish to geta smaller rear-facing child seat.
If the vehicle seat is toofar forward, or the child’s head isthrown forward during a collision, aninflating airbag can strike the childwith enough force to cause veryserious or fatal injuries.
We strongly recommend placing aforward-facing child seat in a backseat, not the front.
We also recommend that a smallchild use the child seat until the childreaches the weight or height limitfor the seat.
Of the different seats available, werecommend those that have a five-point harness system as shown.
Many states, Canadian provinces andterritories allow a child one year ofage or older who also meets theminimum size and weightrequirements to transition from arear-facing child seat to a forwardfacing seat. Know the requirementswhere you are driving and follow thechild seat instructions. Many expertsrecommend use of a rear-facing seatup to age two, if the child’s height
and weight are appropriate for arear-facing seat.
Protecting Small Children
Child Seat Type
Placing a forward-facing child seat inthe front seat of a vehicle equippedwith a passenger’s airbag can behazardous.
Child Seat Placement
Protecting Infants and Small Children
44
Placing a rear-facing child seatin the front seat can result inserious injury or death during acrash.
Always place a rear-facing childseat in the back seat, not thefront.
12/07/13 16:42:28 31TM8630_049
Driver
andP
assengerSafety
TOC
2013 Insight
Even with advanced front airbagsthat automatically turn thepassenger’s front airbag off (seepage ), a back seat is the safestplace for a small child.
If it is necessary to put a forward-facing child seat in the front, movethe vehicle seat as far to the rear aspossible, and be sure the child seat isfirmly secured to the vehicle and thechild is properly strapped in the seat.
Most child seats are LATCH-compatible (Lower Anchors andTethers for CHildren). Some have arigid-type connector, while othershave a flexible-type connector. Bothare equally easy to use. Someexisting and previously owned childseats can only be installed using theseat belt. Whichever type youchoose, follow the child seatmanufacturer’s use and careinstructions as well as theinstructions in this manual. Properinstallation is key to maximizing yourchild’s safety.
In seating positions and vehicles notequipped with LATCH, a LATCH-compatible child seat can be installedusing the seat belt and a top tetherfor added security. This is becauseall child seats are required to bedesigned so that they can be securedwith a lap belt or the lap part of alap/shoulder belt.
In addition, the child seatmanufacturer may advise that a seatbelt be used to attach a LATCH-compatible seat once a child reachesa specified weight. Please read thechild seat owner’s manual for properinstallation instructions.
35
Selecting a Child Seat
Protecting Infants and Small Children, Selecting a Child Seat
45
Placing a forward-facing childseat in the front seat can resultin serious injury or death if thefront airbag inflates.
If you must place a forward-facing child seat in front, movethe vehicle seat as far back aspossible, and properly restrainthe child.
12/07/13 16:42:35 31TM8630_050
Driver
andP
assengerSafety
TOC
2013 Insight
A child seat secured with a seat beltshould be installed as firmly aspossible. However, it does not needto be ‘‘rock solid.’’ Some side-to-sidemovement can be expected andshould not reduce the child seat’seffectiveness.
If the child seat is not secure, tryinstalling it in a different seatingposition, or use a different style ofchild seat that can be firmly secured.
After selecting a proper child seatand a good place to install the seat,there are three main steps ininstalling the seat:
All child seats must besecured to the vehicle with the lappart of a lap/shoulder belt or withthe LATCH (Lower Anchors andTethers for CHildren) system. Achild whose seat is not properlysecured to the vehicle can beendangered in a crash.
After installing a childseat, push and pull the seatforward and from side-to-side toverify that it is secure.
Make sure the child seat meets thefollowing three requirements:
The child seat is the correct typeand size for the child.
The child seat is the correct typefor the seating position.
The child seat is compliant withFederal Motor Vehicle SafetyStandard 213 or Canadian MotorVehicle Safety Standard 213.
Installing a Child SeatImportant considerations whenselecting a child seat
Properly secure the child seat tothe vehicle.
Make sure the child seat is firmlysecured.
1.
2.
Selecting a Child Seat, Installing a Child Seat
46
12/07/13 16:42:43 31TM8630_051
Driver
andP
assengerSafety
TOC
2013 Insight
CONTINUED
To install a LATCH-compatible
Move the seat belt buckleor tongue away from thelower anchors.
Make sure there are no objectsnear the anchors that couldprevent a secure connectionbetween the child seatand the anchors.
Your vehicle is equipped withLATCH (Lower Anchors andTethers for CHildren) at the outerrear seats.
The lower anchors are locatedbetween the seat-back and seatbottom, and are to be used onlywith a child seat designed for usewith LATCH.
The location of each lower anchor isindicated by a small button above theanchor point.
You can find lower anchors in theslits in the seat-backs.
Make sure the child is properlystrapped in the child seataccording to the child seat maker’sinstructions. A child who is notproperly secured in a child seatcan be seriously injured in a crash.
The following pages provideguidelines on how to properly installa child seat. A forward-facing childseat is used in all examples, but theinstructions are the same for a rear-facing child seat.
1.
2.
Installing a Child Seat
Installing a Child Seat with LATCH
Secure the child in the child seat.3.
47
BUTTON
LOWER ANCHORS
12/07/13 16:42:53 31TM8630_052
Driver
andP
assengerSafety
TOC
child seat:
2013 Insight
Lift the head restraint (see page), then route the tether strap
through the legs of the headrestraint and over the seat-back, making sure thestrap is not twisted.
Other LATCH-compatible seats have a flexible-type connectoras shown above.
Whatever type you have, followthe child seat maker’s instructionsfor adjusting or tightening the fit.
Place the child seat on the vehicleseat, then attach the seat to thelower anchors according to thechild seat maker’s instructions.
Some LATCH-compatible seatshave a rigid-type connector asshown above.
5.
4.
3.142
Installing a Child Seat
48
ANCHOR
TETHER STRAP HOOK
Flexible typeRigid type
12/07/13 16:43:01 31TM8630_053
Driver
andP
assengerSafety
TOC
2013 Insight
CONTINUED
With the child seat in the desiredseating position, route the beltthrough the child seat accordingto the seat maker’s instructions,then insert the latch plate into thebuckle and remove any slack fromthe lap portion of the belt.
When not using the LATCH system,all child seats must be secured to thevehicle with the lap part of a lap/shoulder belt.
In addition, the lap/shoulder belts inall seating positions except thedriver’s have a lockable retractorthat must be activated to secure achild seat.
Attach the tether strap hook to thetether anchor, then tighten thestrap as instructed by the childseat maker.
If the tether strap is too long andcannot be tightened firmly, find aroute where the strap can betightened securely.
Push and pull the child seatforward and from side-to-side toverify that it is secure.
1.
6.
7.
Installing a Child Seat
Installing a Child Seat with a Lap/Shoulder Belt
49
12/07/13 16:43:09 31TM8630_054
Driver
andP
assengerSafety
TOC
2013 Insight
Push and pull the child seatforward and from side-to-side toverify that it is secure enough tostay upright during normal driving maneuvers. If thechild seat is not secure, unlatch the belt, allow it to retract fully,then repeat these steps.
To deactivate the lockable retractorand remove a child seat, unlatch thebuckle, unroute the seat belt, and letthe belt fully retract.
To remove slack, it may help toput weight on the child seat, orpush on the back of the seat whilepulling up on the belt.
After confirming that the belt islocked, grab the shoulder part ofthe belt near the buckle, and pullup to remove any slack from thelap part of the belt. Remember, ifthe lap part of the belt is not tight,the child seat will not be secure.
To activate the lockable retractor,slowly pull the shoulder part of thebelt all the way out until it stops,then let the belt feed back into
After the belt has retracted, tug onit. If the belt is locked, you will notbe able to pull it out. If you can pullthe belt out, it is not locked, andyou will need to repeat these steps.
4. 5.2.
3.
Installing a Child Seat
50
12/07/13 16:43:16 31TM8630_055
Driver
andP
assengerSafety
TOC
the retractor.
2013 Insight
If the tether strap is too long andcannot be tightened firmly, find aroute where the strap can betightened securely.
Tighten the strap according to theseat maker’s instructions.
After properly securing the childseat (see page ), lift the headrestraint, then route the tetherstrap over the seat-back andthrough the head restraint legs.
Attach the tether strap hook to theanchor, making sure the strap isnot twisted.
A child seat with a tether can beinstalled in any seating position inthe back seat, using one of theanchorage points shown above.
Since a tether can provide additionalsecurity to the lap/shoulder beltinstallation, we recommend using a tether whenever one is required or available.
1.
2.
3.49
Installing a Child Seat
Installing a Child Seatwith a Tether
51
ANCHORANCHOR
Outer Position Center PositionTETHER STRAP HOOK TETHER STRAP HOOK
ANCHOR
ANCHORAGE POINTS
12/07/13 16:43:24 31TM8630_056
Driver
andP
assengerSafety
TOC
2013 Insight
To determine if a lap/shoulderbelt properly fits a child, have thechild put on the seat belt,then ask yourself:
Does the child sit all the way backagainst the seat?
Do the child’s knees bendcomfortably over the edge ofthe seat?
The following pages giveinstructions on how to check properseat belt fit, what kind of boosterseat to use if one is needed, andimportant precautions for a childwho must sit in front.
When a child reaches therecommended weight or height limitfor a forward-facing child seat, thechild should sit in a back seat on abooster seat and wear the lap/shoulder belt.
1.
2.
Checking Seat Belt Fit
Protecting Larger Children
52
Allowing a child age 12 or underto sit in front can result in injuryor death if the passenger’s frontairbag inflates.
If a child must ride in front,move the vehicle seat as farback as possible, use a boosterseat if needed, have the childsit up properly and wear theseat belt properly.
12/07/13 16:43:31 31TM8630_057
Driver
andP
assengerSafety
TOC
2013 Insight
Does the shoulder belt crossbetween the child’s neck and arm?
Is the lap part of the belt as low aspossible, touching the child’sthighs?
Will the child be able to stayseated like this for the whole trip?
If you answer yes to all thesequestions, the child is ready to wearthe lap/shoulder belt correctly. Ifyou answer no to any question, thechild needs to ride on a booster seat. A child who has outgrown a forward-
facing child seat should ride in aback seat and use a booster seatuntil the lap/shoulder belt fits themproperly without the booster.
Booster seats can be high-back orlow-back. Whichever style you select,make sure the booster seat meetsfederal safety standards (seepage ) and that you follow the
A child may continue using a boosterseat until the tops of their ears areeven with the top of the vehicle’s orbooster’s seat-back. A child of thisheight should be tall enough to usethe lap/shoulder belt without abooster seat.
If a child who uses a booster seatmust ride in front, move the vehicleseat as far back as possible, and besure the child is wearing the seatbelt properly.
Some states, Canadian provinces andterritories also require children touse a booster seat until they reach agiven age or weight (e.g., 6 years or60 lbs). Be sure to check current
laws in the states, provinces orterritories where you intend to drive.
3.
4.
5. 46
Using a Booster Seat
Protecting Larger Children
53
12/07/13 16:43:40 31TM8630_058
Driver
andP
assengerSafety
TOC
booster seat maker’s instructions.
2013 Insight
If the passenger’s front airbaginflates in a moderate to severefrontal collision, the airbag can causeserious injuries to a child who isunrestrained, improperly restrained,sitting too close to the airbag, or outof position.
A side airbag also poses risks. Ifany part of a larger child’s bodyis in the path of a deploying sideairbag, the child could receivepossibly serious injuries.
Physically, a child must be largeenough for the lap/shoulder belt toproperly fit (see pages and ). Ifthe seat belt does not fit properly,with or without the child sitting on abooster seat, the child should not sitin front.
To safely ride in front, a child mustbe able to follow the rules, includingsitting properly, and wearing the seatbelt properly throughout a ride.
If you decide that a child can safelyride up front, be sure to:
Carefully read the owner’s manual, and make sure you understand all seat belt instructions and all safety information.
Move the vehicle seat to the rear-most position.
Have the child sit up straight, backagainst the seat, and feet on ornear the floor.
Check that the child’s seat belt isproperly and securely positioned.
Of course, children vary widely. Andwhile age may be one indicator ofwhen a child can safely ride in front,there are other important factors youshould consider.
The National Highway Traffic SafetyAdministration and TransportCanada recommend that all childrenage 12 and under be properlyrestrained in a back seat.
Supervise the child. Even maturechildren sometimes need to bereminded to fasten the seat beltsor sit properly.
17 52
When Can a LargerChild Sit in Front
Physical Size
Maturity
Protecting Larger Children
54
12/07/13 16:43:50 31TM8630_059
Driver
andP
assengerSafety
TOC
2013 Insight
This could resultin serious neck injuries during
This couldcause very serious injuries duringa crash. It also increases thechance that the child will slideunder the belt in a crash and
If they do, theycould be very seriously injured in
Devices intended toimprove a child’s comfort orreposition the shoulder part of aseat belt can make the belt lesseffective and increase the chanceof serious injury in a crash.
Additional Safety PrecautionsDo not let a child wear a seat beltacross the neck.
Do not let a child put the shoulderpart of a seat belt behind the backor under the arm.
Two children should never use thesame seat belt.
Do not put any accessories on aseat belt.
Protecting Larger Children
55
12/07/13 16:43:55 31TM8630_060
Driver
andP
assengerSafety
TOC
a crash.
a crash.
be injured.
2013 Insight
Your vehicle’s exhaust containscarbon monoxide gas. Carbonmonoxide should not enter thevehicle in normal driving if youmaintain your vehicle properly andfollow the information on this page.
High levels of carbon monoxide cancollect rapidly in enclosed areas,such as a garage. Do not run theengine with the garage door closed.Even with the door open, run theengine only long enough to move thevehicle out of the garage.
Have the exhaust system inspectedfor leaks whenever:
Select the fresh air mode.Select the mode.Set the fan speed to high.Set the temperature control to acomfortable setting.
With the hatch open, airflow can pullexhaust gas into your vehicle’sinterior and create a hazardouscondition. If you must drive with thehatch open, open all the windows,and set the climate control system asshown below.
If you must sit in your parked vehiclewith the engine running, even in anunconfined area, adjust the climatecontrol system as follows:
The vehicle is raised for an oil change.
You notice a change in the soundof the exhaust.
The vehicle was in a crash thatmay have damaged the underside.
1.2.3.4.
Carbon Monoxide Hazard
56
Carbon monoxide gas is toxic.Breathing it can causeunconsciousness and even killyou.
Avoid any enclosed areas oractivities that expose you tocarbon monoxide.
12/07/13 16:44:03 31TM8630_061
Driver
andP
assengerSafety
TOC
2013 Insight
These labels are in the locationsshown. They warn you of potentialhazards that could cause seriousinjury or death. Read these labelscarefully.
If a label comes off or becomes hardto read (except for the U.S.dashboard label which may beremoved by the owner), contact yourdealer for a replacement.
CONTINUED
U.S. models
Canadian models
U.S. models only
Safety Labels
57
DASHBOARD
RADIATOR CAP
SUN VISORS
12/07/13 16:44:17 31TM8630_062
Driver
andP
assengerSafety
TOC
2013 Insight
U.S. models Canadian models
Safety Labels
58
DOORJAMBS
12/07/13 16:44:25 31TM8630_063
Driver
andP
assengerSafety
TOC
2013 Insight
This section gives information aboutthe controls and displays thatcontribute to the daily operation ofyour vehicle. All the essentialcontrols are within easy reach.
...........................Control Locations . 60............................Instrument Panel . 61
..........Instrument Panel Indicators . 62.............................................Gauges . 72
.............Multi-Information Display . 75Controls Near the Steering
.........................................Wheel . 118Windshield Wipers and
.....................................Washers . 119.......Turn Signals and Headlights . 120
.........Daytime Running Lights . 123......Instrument Panel Brightness . 124
...............Hazard Warning Button . 125
...............Rear Window Defogger . 126................................ECON Button . 127
......Steering Wheel Adjustments . 128.............................Keys and Locks . 129
......................Immobilizer System . 130..............................Ignition Switch . 131
....................................Door Locks . 133............Childproof Door Locks . 134
.....................Remote Transmitter . 135..............................................Hatch . 139
................Unlocking the Hatch . 140...............................................Seats . 141
...........Front Seat Adjustments . 141
Driver’s Seat Height............................Adjustment . 141
........................Head Restraints . 142.Folding the Rear Seats Down . 145
......................................Armrest . 146...........................................Mirrors . 147
..Adjusting the Power Mirrors . 147..............Power Mirror Heaters . 148
............................Power Windows . 149...............................Parking Brake . 151
.........Interior Convenience Items . 152...............Under Floor Storage . 153
.Floor Storage Compartments . 153.....................Beverage Holders . 154
.........Accessory Power Socket . 155.............Console Compartment . 155
..................................Glove Box . 156...............................Center Tray . 156
..........................Center Pockets . 157..................................Coat Hook . 158..................................Sun Visors . 158
............................Vanity Mirror . 158...............................Interior Lights . 159
Instruments and Controls
Instruments
andC
ontrols
59
12/07/13 16:44:30 31TM8630_064
2013 Insight
**
*
**
If equippedRefer to the navigation system manual.
1 :2 :
Control Locations
60
(P.72) (P.72, P.75)
EX model with navigation system is shown.
HAZARD WARNING BUTTONMULTI-INFORMATION DISPLAYINSTRUMENT PANEL INDICATORSGAUGES
ECON BUTTON
DOOR LOCK TAB
POWER WINDOWSWITCHES
HOOD RELEASE HANDLE
AUDIO SYSTEM
PASSENGER AIRBAGOFF INDICATOR(P.35)
PARKING BRAKE LEVER
AUTOMATICTRANSMISSION (CVT)
CLIMATE CONTROLSYSTEM
(P.62)
MIRROR CONTROLS(P.147)
(P.127)
(P.133)
(P.133)
(P.149)
NAVIGATION SYSTEM
(P.151)
USB ADAPTER CABLEPADDLE SHIFTERS
POWER DOOR LOCKMASTER SWITCH
(P.125)
(P.168)
(P.162)
(P.271)
(P.197, P.205)(P.276)
(P.248)
2
11
12/07/13 16:44:36 31TM8630_065
Instruments
andC
ontrols
TOC
2013 Insight
*
*
**
*
The U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.
Instrument Panel
61
LIGHTS ON INDICATOR
SEAT BELT REMINDERINDICATOR
ANTI-LOCK BRAKE SYSTEM(ABS) INDICATOR
SUPPLEMENTAL RESTRAINTSYSTEM (SRS) INDICATOR
SYSTEM MESSAGEINDICATORBRAKE SYSTEM INDICATOR
(AMBER)
VSA OFF INDICATOR
MALFUNCTIONINDICATOR LAMP PARKING BRAKE AND
BRAKE SYSTEMINDICATOR (RED)
DOOR/HATCH OPENINDICATOR
SIDE AIRBAG OFFINDICATOR
IMMOBILIZERSYSTEM INDICATOR
IMA SYSTEMINDICATOR
HIGH BEAMINDICATOR
ELECTRIC POWER STEERINGINDICATOR
(P.64)
(P.63)
(P.66)
: If equipped (P.62)
(P.64)
(P.65)
(P.68)
(P.68)
(P.69)
(P.64)
(P.69)
HIGH TEMPERATURE INDICATOR (P.67)
LOW TEMPERATURE INDICATOR(P.67)
(P.70)
(P.66)
CRUISE MAIN INDICATOR (P.69)
CRUISE CONTROL INDICATOR (P.69)
LOW OIL PRESSUREINDICATOR LOW TIRE PRESSURE/
TPMS INDICATOR
12 VOLT BATTERYCHARGING SYSTEMINDICATOR
(P.70)
ECON MODE INDICATOR (P.71)
(P.70)
AUTO IDLE STOP INDICATOR
LOW FUEL INDICATOR
VEHICLE STABILITY ASSIST(VSA) SYSTEM INDICATOR
SECURITY SYSTEM INDICATOR
(P.65, P.293)
(P.65, P.293)
(P.66, P.281, P.283)(P.63, P.366)
(P.62, P.365)
(P.63, P.364)
(P.62, P.363)
12/07/23 10:21:03 31TM8630_066
Instruments
andC
ontrols
TOC
2013 Insight
The instrument panel has manyindicators to give you importantinformation about your vehicle.
If your front passenger does notfasten their seat belt, the indicatorcomes on about 6 seconds after theignition switch is turned to the ON(II) position.
This indicator comes on when youturn the ignition switch to the ON(II) position. It reminds you and yourpassengers to fasten your seat belts.A beeper also sounds if you have notfastened your seat belt.
You will also see a ‘‘FASTEN SEATBELT’’ message on the multi-information display.
If you turn the ignition switch to theON (II) position before fasteningyour seat belt, the beeper soundsand the indicator flashes. If you donot fasten your seat belt before thebeeper stops, the indicator stopsflashing but remains on.
If either of you do not fasten yourseat belt while driving, the beeperwill sound and the indicator will flashagain at regular intervals, and youwill see a ‘‘FASTEN SEAT BELT’’ or‘‘FASTEN PASSENGER SEATBELT’’ message on the multi-information display. For moreinformation, see page .
You will also see a ‘‘CHECKEMISSION SYSTEM’’ message onthe multi-information display. Formore information, see page .
The engine can be severely damagedif this indicator flashes or stays onwhen the engine is running, and youwill see a ‘‘CHECK ENGINE OILLEVEL’’ message on the multi-information display. For moreinformation, see page .
21
365
363
Instrument Panel Indicators
Seat Belt ReminderIndicator
Malfunction IndicatorLamp
Low Oil PressureIndicator
62
12/07/13 16:44:54 31TM8630_067
Instruments
andC
ontrols
TOC
2013 Insight
If it stays on after you have fullyreleased the parking brake whilethe engine is running, or if itcomes on while driving, it canindicate a problem in the brakesystem. You will also see a‘‘BRAKE FLUID LOW’’ or‘‘CHECK BRAKE SYSTEM’’message on the multi-informationdisplay. For more information, seepage .
This indicator comes on briefly whenyou turn the ignition switch to theON (II) position. It will then go off ifyou have inserted a properly codedignition key. If it is not a properlycoded key, the indicator will blink,and the engine’s fuel system will bedisabled (see page ).
If this indicator comes on when theengine is running, the 12 volt batteryis not being charged, and you willalso see a ‘‘CHECK CHARGINGSYSTEM’’ message on the multi-information display. For moreinformation, see page .
This indicator has two functions:It comes on when you turn theignition switch to the ON (II)position. It is a reminder to checkthe parking brake. Driving withthe parking brake not fullyreleased can damage the brakesand tires.
If you drive without releasing theparking brake, a beeper will sound,and you will also see a ‘‘RELEASEPARKING BRAKE’’ message onthe multi-information display (seepage ).
1.
2.
130
151
364366
Instrument Panel Indicators
Immobilizer SystemIndicator
12 Volt Battery ChargingSystem Indicator
Parking Brake andBrake SystemIndicator (Red)
63
U.S. Canada
12/07/13 16:45:03 31TM8630_068
Instruments
andC
ontrols
TOC
2013 Insight
This indicator normally comes on fora few seconds when you turn theignition switch to the ON (II)position, and START (III) position.When the brake system indicator(amber) comes on and stays on,there is a problem with the CreepAid System or Brake Assist (thenormal brake operates properly).Have your vehicle checked by yourdealer. For more information, seepage .
You will also see a ‘‘CHECK BRAKESYSTEM’’ message on the multi-information display (see page ).
This indicator normally comes on fora few seconds when you turn theignition switch to the ON (II)position. If it comes on at any othertime, there is a problem with theABS. If this happens, have yourvehicle checked at a dealer. Withthis indicator on, your vehicle stillhas normal braking ability but noanti-lock function. For moreinformation, see page .
This indicator comes on briefly whenyou turn the ignition switch to theON (II) position. If it comes on atany other time, it indicates apotential problem with your frontairbags. This indicator will also alertyou to a potential problem with yourairbag system components. Formore information, see page .
You will also see a ‘‘CHECK ABSSYSTEM’’ message on the multi-information display (see page ).
You will also see a ‘‘CHECKAIRBAG SYSTEM’’ messageon the multi-information display(see page ).
89
89
34
89285
287
Instrument Panel Indicators
Brake SystemIndicator(Amber)
Anti-lock Brake System(ABS) Indicator
Supplemental RestraintSystem Indicator
64
U.S. Canada
12/07/13 16:45:12 31TM8630_069
Instruments
andC
ontrols
TOC
2013 Insight
This indicator comes on briefly whenyou turn the ignition switch to theON (II) position. If it comes on atany other time, it indicates that thepassenger’s side airbag hasautomatically shut off. You will alsosee a ‘‘PASSENGER SIDE AIRBAGOFF’’ message on the multi-information display. For moreinformation, see page .
This indicator normally comes on fora few seconds when you turn theignition switch to the ON (II)position. For more information, seepage .
It comes on as a reminder that youhave turned off the vehicle stabilityassist (VSA) system.
If the VSA indicator illuminates, hillstart assist will not be working.Without hill start assist, the vehiclewill roll downhill immediately whenyou release the brake on an incline.
You will also see a ‘‘CHECK VSASYSTEM’’ or ‘‘CHECK HILL STARTASSIST SYSTEM’’ message on themulti-information display (see
).
If it comes on and stays on at anyother time, there is a problem withthe VSA or hill start assist system.Take your vehicle to a dealer tohave it checked. Without VSA,your vehicle still has normaldriving ability, but will not haveVSA traction and stabilityenhancement. See page
This indicator normally comes on fora few seconds when you turn theignition switch to the ON (II)position.
This indicator has two functions:
It flashes when VSA is active(see page ).
34
1.
2.
293
293
293
Instrument Panel Indicators
Vehicle Stability Assist(VSA) System IndicatorSide Airbag Off
Indicator
VSA OFF Indicator
65
U.S. Canada
12/07/13 16:45:23 31TM8630_070
Instruments
andC
ontrols
TOC
for more information on theVSA system.
page 90
2013 Insight
If this happens, pull to the side of theroad when it is safe, check which tirehas lost pressure, and determine thecause. If it is because of a flat tire,replace the flat tire with the compactspare (see page ), and have theflat tire repaired as soon as possible.If two or more tires are underinflated,call a professional towing service.Refer to page for moreinformation.
If this indicator begins to flash,there is a problem with the tirepressure monitoring system(TPMS). You will also see a‘‘CHECK TPMS SYSTEM’’message on the multi-informationdisplay. The indicator continues toflash for a while (approximately 1minute), then stays on. If thishappens, have your dealer checkthe system as soon as possible.For more information, see
.
This indicator normally comes on for a few seconds when you turn the ignition switch to the ON (II)position. If it comes on at any other time, it indicates aproblem in the integrated motorassist (IMA) system. With the IMAindicator on, the vehicle may notaccelerate as it normally does. Havethe vehicle checked by the dealeras soon as possible.
You will also see a ‘‘CHECK IMASYSTEM’’ message on the multi-information display.
See pages and .
You will also see a ‘‘CHECK TIREPRESSURE’’ message on the multi-information display (see page ).
If it comes on while driving, itindicates that one or more of yourvehicle’s tires are significantly lowon pressure.
This indicator has two functions:
This indicator normally comes on fora few seconds when you turn theignition switch to the ON (II)position.
1.
2.
281 283
289
349
374
U.S. models only
Instrument Panel Indicators
Low Tire Pressure/TPMS Indicator
IMA System Indicator
Auto Idle Stop Indicator
66
12/07/13 16:45:34 31TM8630_071
Instruments
andC
ontrols
TOC
page 290
2013 Insight
If the indicator begins to blink orstays on, you will also see a ‘‘WATERTEMP HOT’’ message on the multi-information display. This warningwill alert you that the engine shouldbe cooled down.
This indicator shows thetemperature of the engine coolant. Itnormally comes on when you turnthe ignition switch to the ON (II)position and goes off after a fewseconds. In normal drivingconditions, this indicator should notblink or stay on. In severe drivingconditions, such as very hot weatheror a long period of uphill driving, thisindicator may blink. This means theengine coolant temperature is high.If the indicator begins to blink whileyou are driving, be sure to slow downto prevent overheating. If theindicator stays on, pull safely to theside of the road and turn off theengine. See page for instructionsand precautions on checking theengine’s cooling system.
Do not drive the vehicle while theindicator is on or the engine may bedamaged.
This indicator shows thetemperature of the engine coolant. Ifthere is no problem, this indicatorcomes on when the engine is cold. Ifit comes on when the engine is warm(normal operating temperature),have the vehicle inspected by yourdealer as soon as possible.
360
Instrument Panel Indicators
High TemperatureIndicator
Low TemperatureIndicator
67
12/07/13 16:45:42 31TM8630_072
Instruments
andC
ontrols
TOC
2013 Insight
This indicator normally comes onwhen you turn the ignition switch tothe ON (II) position and goes offafter the engine starts. If it comes onat any other time, there is a problemin the electric power steering system.
If this happens, stop the vehicle in asafe place and turn off the engine.Reset the system by restarting theengine. The indicator will stay on,but should go off after driving ashort distance. If it does not go off,or comes back on again while driving,take the vehicle to your dealer tohave it checked. With the indicatoron, the EPS may be turned off,making the vehicle harder to steer.
If you turn the steering wheel to thefull left or right position repeatedlywhile stopping or driving at very lowspeed, you may feel slightly hardersteering in order to prevent damageto the steering system caused byoverheating. This may also happen ifyou hold the steering wheel on thefull left or right position for a while.
This indicator comes on red ifany door or the hatch lid is notclosed tightly.
You will also see a correspondingindicator(s) on the multi-informationdisplay to indicate which door and/or the hatch is not closed tightly (seepage ).You will also see a ‘‘CHECK POWER
STEERING SYSTEM’’ message onthe multi-information display.
12
Electric Power Steering(EPS) Indicator
Door/Hatch OpenIndicator
Instrument Panel Indicators
68
12/07/13 16:45:49 31TM8630_073
Instruments
andC
ontrols
TOC
2013 Insight
This indicator reminds you that theexterior lights are on. It comes onwhen the light switch is in either the
or position. If you turn theignition switch to the ACCESSORY(I) or the LOCK (0) position withoutturning off the light switch, thisindicator will remain on. A reminderchime will also sound when you openthe driver’s door.
This indicator comes on with thehigh beam headlights. For moreinformation, see page .
This indicator also comes on withreduced brightness when thedaytime running lights (DRL) are on(see page ).
The left or right turn signal indicatorblinks when you signal a lane changeor turn. If an indicator does not blinkor blinks rapidly, it usually meansone of the turn signal bulbs isburned out (see pages and ).Replace the bulb as soon as possible,since other drivers cannot see thatyou are signaling.
When you press the hazard warningbutton, both turn signal indicatorsand all turn signals on the outside ofthe vehicle flash.
This indicator comes on when youturn on the cruise control system bypressing the CRUISE button on thesteering wheel (see page ).
This indicator comes on when youset the cruise control. See page
for information on operating thecruise control.
121
123
325 327
222
222
On LX and EX models
On LX and EX models
Cruise Main IndicatorLights On Indicator
High Beam Indicator
Turn Signal andHazard WarningIndicators
Cruise Control Indicator
Instrument Panel Indicators
69
12/07/13 16:45:59 31TM8630_074
Instruments
andC
ontrols
TOC
2013 Insight
This indicator is in the fuel gauge. Itcomes on as a reminder that youmust refuel soon. You will also see a‘‘FUEL LOW’’ message on the multi-information display.
When the needle reaches E, thereis a very small amount offuel in the tank.
This indicator comes on when thereis a system message on the multi-information display. Press the INFObutton on the steering wheel (seepage ) to see the message (seepage ).
Most of the time, this indicatorcomes on along with other indicatorsin the instrument panel such as theseat belt reminder indicator, SRSindicator, VSA system indicator, etc.
When the indicator comes on, thereare about 1.8 U.S. gal (6.9 ) of fuelremaining in the tank.
This indicator comes on when thesecurity system is set. For moreinformation, see page .
7689
221
On LX and EX modelsLow Fuel Indicator System Message
IndicatorSecurity System Indicator
Instrument Panel Indicators
70
LOW FUEL INDICATOR
SECURITY SYSTEM INDICATOR
12/07/13 16:46:08 31TM8630_075
Instruments
andC
ontrols
TOC
2013 Insight
This indicator normally comes on fora few seconds when you turn theignition switch to the ON (II)position. When you turn the econmode on by pressing the ECONbutton with the ignition switch in theON (II) position, this indicator willcome on.
You will also see the symbol on themulti-information display with ECONON or ECON OFF (see page ).75
ECON Mode Indicator
Instrument Panel Indicators
71
12/07/13 16:46:12 31TM8630_076
Instruments
andC
ontrols
TOC
2013 Insight
This shows your speed in kilometersper hour (km/h) or miles per hour(mph) depending on the selectedspeedometer display. You can switchthe display between km/h and mph(see page ).
The speedometer also has anambient meter. The color of theambient meter changesautomatically according to yourdriving style (see page ).
You can customize the setting of theambient meter (see page ).
73
103
266
Gauges
Speedometer/Ambient Meter
72
U.S. model is shown.
MULTI-INFORMATIONDISPLAY
SPEEDOMETER/AMBIENT METER
CHARGE/ASSIST GAUGE TACHOMETER FUEL GAUGE
KM/MILE CHANGE KNOB SEL/RESET KNOB
12/07/13 16:46:18 31TM8630_077
Instruments
andC
ontrols
TOC
2013 Insight
This shows how much fuel you have.It may show slightly more or lessthan the actual amount. The needlereturns to the bottom after you turnoff the ignition.
To switch the lower segment of themulti-information display betweenthe odometer with the outsidetemperature and trip meter with theoutside temperature, press the sel/reset knob repeatedly. For moreinformation, see page .
Each time you press and hold thekm/mile change knob, thespeedometer reading switchesbetween miles per hour (mph) andkilometers per hour (km/h).
78
Fuel GaugeSel/Reset Knob Km/Mile Change Knob
GaugesInstrum
entsand
Controls
73
SEL/RESET KNOB KM/MILE CHANGE KNOB
Avoid driving with an extremely lowf uel level. Running out of f uel couldcause the engine to misf ire, damagingthe catalytic converter.
12/07/13 16:46:26 31TM8630_078
Instruments
andC
ontrols
TOC
2013 Insight
This gauge shows you the charge/discharge status of the IntegratedMotor Assist (IMA). When the IMAis assisting the engine, the pointerstays in the assist gauge (upper partof the gauge). When the IMAbattery is being charged, the pointerstays in the charge gauge (lower partof the gauge).
You can also check the status of theIMA system function on the multi-information display (see page ).
If the IMA battery is too hot or toocold, the IMA system limits the IMAbattery’s output power to protect thebattery. This disables the IMA assistand auto idle stop, even though thebattery level indicator on the multi-information display may show thatthe battery is well-charged (see ~~~~
). Therefore, if the motor
It takes a short time to normalize theIMA battery’s output powerdepending on the weather.
84
Charge/Assist Gauge
Gauges
74
IMA ASSIST GAUGE
IMA CHARGE GAUGE
12/07/13 16:46:32 31TM8630_079
Instruments
andC
ontrols
TOC
assist is frequently used, thebattery becomes hot and starts tolimit its output power.
page 85
2013 Insight
The multi-information display in theinstrument panel displays variousinformation and messages when theignition switch is in the ON (II)position. Some of the messages helpyou operate your vehicle morecomfortably. Others help to keepyou aware of the periodicmaintenance your vehicle needs forcontinued trouble-free driving.
If you do not fasten your seat belt,you will see a ‘‘FASTEN SEATBELT’’ message on the multi-information display when you turn the ignition switch to the ON (II) position.
These messages go off severalseconds after the key is inserted intothe ignition switch.
There are three types of messages:normal display messages, engine oillife and maintenance messages, andsystem messages.
You can select the displayedlanguage and also customize somevehicle control settings to your likingwith the multi-information displayand the three buttons on the steeringwheel (see page ).
You will see an ‘‘ECON ON’’ or‘‘ECON OFF’’ message on the multi-information display according to theprevious ECON setting when youturn the ignition switch to the ON(II) position (see page ).
76
127
CONTINUED
Normal Display Messages
Multi-Information Display
75
ECON is On. ECON is Off.
12/07/13 16:46:40 31TM8630_080
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
▲ ▼
▲ ▼
The multi-information displaychanges to the blank display shownabove several seconds afteryou turn the ignition switch to theON (II) position.
With the ignition switch in the ON(II) position, the multi-informationdisplay changes as shown on page 78each time you press the INFO( / ) button or SEL/RESETbutton.
Multi-Information Display
76
U.S. model is shown.
SEL/RESET BUTTON
INFO ( / ) BUTTONSEL/RESET BUTTON
INFO BUTTONS ( / )
LX and EX models Insight model
12/07/13 16:46:46 31TM8630_081
Instruments
andC
ontrols
TOC
2013 Insight
In the multi-information display, thesystem message is also displayed(see page ) and you cancustomize your vehicle controlsettings (see page ).
The multi-information displayconsists of an upper segment, amiddle segment and a lowersegment.
In the normal display mode, theupper and middle segments displaytrip computer information, such asfuel economy or average speed. Thelower segment displays theodometer/trip meter (A/B), outsidetemperature, and engine oil life andmaintenance item code(s).
88
91
CONTINUED
Multi-Information Display
77
MIDDLESEGMENT
U.S. model is shown.
LOWERSEGMENT
UPPERSEGMENT
12/07/13 16:46:52 31TM8630_082
Instruments
andC
ontrols
TOC
2013 Insight
*
▼▲
*
Multi-Information Display
78
U.S. model is shown.
: This display will be shown when theBluetooth HandsFreeLink is activated.
IMA System PowerFlow Monitor/IMA Battery LevelIndicator(See page 84, 85)
: Press the INFO button .
: Press the INFO button .
: Press the SEL/RESET button.
HFL (See page 87)
Average FuelEconomy Record(See page 81)
Engine Oil Life(See page 80)
Outside Temperature(See page 80)
Trip Computer (See page 81)
EcologicalDrive Display(See page 81)
12/07/13 16:46:58 31TM8630_083
Instruments
andC
ontrols
TOC
2013 Insight
The odometer shows the totaldistance your vehicle has beendriven. It measures miles in U.S.models and kilometers in Canadianmodels. It is illegal under U.S.federal law and Canadian provincial/territorial regulations to disconnect,reset, or alter the odometer with theintent to change the number of milesor kilometers indicated.
This meter shows the number ofmiles (U.S.) or kilometers (Canada)driven since you last reset it. Thereare two trip meters: Trip A and TripB. Each trip meter worksindependently, so you can keep trackof two different distances.
When you reset Trip A, average fueleconomy A is reset at the same time.When you reset Trip B, average fueleconomy B is reset.
In the customizing mode, you can setTrip A and average fuel economy Ato reset when you refuel your vehicle(see page ).
To reset a trip meter, display it,then press and hold the SEL/RESET button until the numberresets to ‘‘0.0’’.
99
Odometer Trip Meter
Multi-Information Display
79
TRIP METER A TRIP METER B
ODOMETER U.S. model is shown.
U.S. Canada
12/07/13 16:47:08 31TM8630_084
Instruments
andC
ontrols
TOC
2013 Insight
This shows the outside Fahrenheittemperature in U.S. models, andCelsius temperature in Canadianmodels.
In certain weather conditions,temperature readings near freezing(32°F, 0°C) could mean that ice isforming on the road surface.
You can adjust the outsidetemperature display (see page ).
The temperature sensor is in thefront bumper. The temperaturereading can be affected by heatreflection from the road surface,engine heat, and the exhaust fromsurrounding traffic. This can causean incorrect temperature readingwhen your vehicle speed is under19 mph (30 km/h). When you startyour trip, the sensor is not fullyacclimatized, therefore it may takeseveral minutes until the propertemperature is displayed.
This shows the remaining engine oillife. It shows 100% after the engineoil is replaced and the display is reset.The engine oil life is calculatedbased on engine operating conditions.For more information, see page .
98299
Outside Temperature Engine Oil Life
Multi-Information Display
80
OUTSIDE TEMPERATURE
ENGINE OIL LIFE
U.S. Canada
12/07/13 16:47:16 31TM8630_085
Instruments
andC
ontrols
TOC
2013 Insight
Ecological drive display consists ofthree parts. The eco-drive scoredisplay shows the accumulated
acceleration efficiency. The de-celeration monitor shows decelerationefficiency. See page 265 formore information.
The average fuel economy recordsdisplay shows the average fueleconomy (0) for the current drivingcycle and (1-3) for the last threedriving cycles in mpg (U.S. models)or l/100 km (Canadian models).
Indicators in the trip computer show:
Average Fuel Economy
RangeElapsed TimeAverage Vehicle Speed
Instant Fuel Economy
CONTINUED
Ecological Drive Display Average Fuel Economy Records Trip Computer
Multi-Information Display
81
U.S. model is shown.
DECELERATIONMONITOR
ACCELERATIONMONITOR
LATESTAVERAGE FUELECONOMY
PAST AVERAGEFUEL ECONOMY
ECO-DRIVE SCORE DISPLAYU.S. Canada
12/07/13 16:47:28 31TM8630_086
Instruments
andC
ontrols
TOC
eco score for one driving cycle.The acceleration monitor shows
2013 Insight
Mile indication (U.S. models):
Kilometer indication (Canadian models):
Average Fuel Economy A:
Average Fuel Economy B:
This shows your vehicle’s instantfuel economy in mpg.
This shows your vehicle’s averagefuel economy in mpg (U.S. models)or l/100 km (Canadian models) sinceyou last reset trip computer A.
This shows your vehicle’s averagefuel economy in mpg (U.S. models)or l/100 km (Canadian models) sinceyou last reset trip computer B.
You can customize the Trip A andAverage Fuel Economy A resetcondition on the multi-informationdisplay (see page ).
This shows your vehicle’s instantfuel economy in l/100 km.
When you turn off the engine, theinstant fuel economy (mpg or
The average fuel economy will bereset when you reset the trip meter,or if the vehicle’s 12 volt battery goesdead or is disconnected.
99
Average Fuel Economy A/BInstant Fuel Economy
Multi-Information Display
82
U.S.
AVERAGE FUELECONOMY A
AVERAGE FUELECONOMY B
U.S.
INSTANTFUELECONOMY
Canada
Canada
12/07/13 16:47:40 31TM8630_087
Instruments
andC
ontrols
TOC
1/100 km) is also reset.
2013 Insight
This shows the average speed youare traveling in miles per hour (mph)for U.S. models or kilometers perhour (km/h) for Canadian models.
This shows the accumulatedtraveling time since you last reset it.When you turn the ignition switch tothe ON (II) position, ELAPSEDTIME is reset.
This shows the estimated distanceyou can travel on the fuel remainingin the fuel tank. This distance isestimated from the fuel economyyou received over the last severalmiles (U.S.) or kilometers (Canada),so it will vary with changes in speed,traffic, etc.
If you want to reset the ELAPSEDTIME manually, go to the tripcomputer’s ELAPSED TIME display,and press and hold the SEL/RESETbutton until the number resets.
You can customize the ELAPSEDTIME reset conditions on the multi-information display (see page ).
To reset the AVG. SPEED reading,press and hold the SEL/RESETbutton until the number resets.
100
ELAPSED TIMERANGE AVG. SPEED
Multi-Information Display
83
12/07/13 16:47:48 31TM8630_088
Instruments
andC
ontrols
TOC
2013 Insight
The IMA system power flow monitorshows the status of the IMA system.The energy source, and poweringstatus of the engine and IMA motor(engine operation icon and IMAbattery) are represented by arrowson the display. The battery levelindicator shows the state of chargeof the IMA battery.
The table in the next column showsthe basic monitoring displayexamples and their descriptions.
ExampleDescriptionsOnly IMA motor ispowering the vehicle andIMA battery is discharging.
IMA motor is assisting theengine with powering thevehicle. IMA battery isdischarging and the systemis consuming fuel.IMA system is chargingIMA battery.
Only engine is poweringvehicle. The system isconsuming fuel.
Engine is powering vehicleand IMA system is chargingIMA battery. The system isconsuming fuel.
IMA System Power Flow Monitor Powering Status
Multi-Information Display
84
IMA BATTERY/BATTERYLEVEL INDICATOR
POWER FLOW
ENGINEOPERATIONICON
12/07/13 16:47:57 31TM8630_089
Instruments
andC
ontrols
TOC
2013 Insight
The IMA battery level indicatorshows you the state of charge ofthe battery for the Integrated Motor Assist (IMA). This battery isrecharged and discharged by theIMA motor depending on thedriving conditions.
The position of the battery levelreading shows the state of charge ofthe IMA battery. When the batterylevel reading is high, the IMAbattery is well charged. There areseven positions (Level 0-Level 6) ofthe battery level reading.
The battery level reading may dropnear the bottom under drivingconditions that require IMA motorassistance for a long time, such asprolonged acceleration or climbing along hill.
The IMA motor will recharge thebattery as you continue driving.
CONTINUED
IMA Battery Level Indicator
Multi-Information Display
85
LEVEL READING
Lowestlevel ofstate ofcharge
Highestlevel ofstate ofcharge
IMA BATTERY LEVEL INDICATOR
Level 0 Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
12/07/13 16:48:04 31TM8630_090
Instruments
andC
ontrols
TOC
2013 Insight
On vehicle with paddle shifters
On vehicle without paddle shifters
The IMA battery is charged at ahigher rate when the transmission isin L (Low) mode (see page ).
The battery level gauge does notread the battery level directly. Itcalculates the level by continuouslymeasuring the current flow, voltage,and temperature.
If the battery is mostly discharged,the auto idle stop function is disabled(see page ).
The IMA battery is charged at ahigher rate when the transmission isin LOW (L) range (see page ).
Since the level is not read directly,small sensing errors can, over time,cause the gauge to read higherthan the actual battery level. Thesystem will then perform acorrection, and the battery level gauge reading will drop suddenly.When this happens, IMA assistand Auto Idle Stop are disabled until the IMA battery is sufficientlyrecharged by normal driving.
This correction of the battery levelgauge is normal and does notindicate a problem. If the IMAbattery develops a problem orbecomes deteriorated, the IMAsystem indicator will come on. If thishappens, have the vehicle checkedby your dealer as soon as possible.
280
274
281
Multi-Information Display
86
12/07/13 16:48:12 31TM8630_091
Instruments
andC
ontrols
TOC
2013 Insight
To use the system, your cell phoneand the HFL system must be linked.Not all cell phones are compatiblewith this system. Refer to page 225for instructions on how to linkyour cell phone to HFL and how toreceive or make phone calls, or visitthe handsfreelink.com website. InCanada, visit , orcall (888) 528-7876.
You can receive or make phone callsfrom your cell phone through yourvehicle’s HandsFreeLink(HFL) system without touching yourcell phone.
www.handsfreelink.ca
Bluetooth
Bluetooth HandsFreeLink
Multi-Information Display
87
12/07/13 16:48:16 31TM8630_092
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
▲ ▼
▲ ▼If there is a problem with yourvehicle, for example the engine oillevel is low or a door is not fullyclosed, the multi-information displaywill show you the problem. It doesthis by interrupting the currentdisplay with one or more messages.
The system message(s) triggers theappropriate indicator(s) on theinstrument panel, including thesystem message indicator, to comeon. The system message indicatordoes not go off until the problem(s)is corrected.
You will also hear a beep when thesystem message comes on for thefirst time.
Most of the messages are displayedfor about 5 seconds, and then thenormal display returns. If there areseveral system messages to beshown, the display switches thesemessages every 5 seconds.
To switch the message(s) before 5seconds have elapsed, press theINFO ( / ) button on the steeringwheel.
Even if you press the INFO ( / )button, some messages stay on orcome on again at regular intervalsuntil the problem is corrected.
If the system message indicatorremains lit on the instrument panel,you can see the correspondingmessage(s) again by pressing theINFO ( / ) button repeatedly.
System Messages
Multi-Information Display
88
SYSTEM MESSAGE INDICATOR
12/07/13 16:48:24 31TM8630_093
Instruments
andC
ontrols
TOC
A list of all messages begins on the next page:
2013 Insight
CONTINUED
See page12
See page13
See page13
See page21
See page21
See page34
See page34
See page64
See page66
See page151
See page319
See page366
See page365
See page364
See page287
See page363
Multi-Information Display
89
U.S.
U.S.
Canada
Canada
12/07/13 16:48:38 31TM8630_094
Instruments
andC
ontrols
TOC
2013 Insight
See page68
See page80
See page70
See page131
See page131
See page132
See page123
See page293
See page289
See page290
See page360
See page271
See page317
See page300
See page301
See page302
See page247
Multi-Information Display
90
U.S.only
U.S.only
Canadaonly
12/07/13 16:48:51 31TM8630_095
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
You can customize some vehiclecontrol settings. To enter thecustomizing mode, press and holdeither INFO button ( / ) for morethan 3 seconds. To change thesettings, the ignition switch must bein the ON (II) position, and thevehicle must be stopped with thetransmission in Park.
If you turn the ignition switch to theACCESSORY (I) or the LOCK (0)position, or move the shift lever outof Park, the display will change tothe normal screen.
If you try to enter the customizingmode while the vehicle is moving,you will see a ‘‘MUST STOP ANDSHIFT TO PARK TO CHANGESETTINGS’’ message and youcannot change the settings.
If you want to change any vehiclecontrol settings, select CHGSETTING, then press the SEL/RESET button.
Refer to the table on the followingpages about the settings you wantto customize.
CONTINUED
Customized Settings
Multi-Information Display
91
12/07/13 16:48:58 31TM8630_096
Instruments
andC
ontrols
TOC
2013 Insight
*
*
*
*
*
*
*
*
*
- ~± ~
- ~± ~
*
Group Setup Menu Item Description PageSetting OptionMETER SETUP(P.96)
LIGHTING SETUP(P.104)
LANGUAGE SELECTION
ADJUST OUTSIDE TEMP.DISPLAY
TRIP A RESET withREFUELELAPSED TIME RESET
DISPLAY KM/MILES
METER COLOR CHANGE
INTERIOR LIGHTDIMMING TIMEAUTO LIGHTSENSITIVITY
Changes the language used in the display.
Changes the outside temperature reading above orbelow its current reading.
Causes trip meter A and the average fuel economyto reset when you refuel.Resets the elapsed time of your current trip.
Changes the displayed measurement on the multi-information display.
Turn the ambient meter feature on or off.
Changes how long (in seconds) the interior lightsstay on after you close the doors.Changes the timing of when the headlights comeon. The headlight switch needs to be in the AUTOposition.
97
98
99
100
101
103
105
106
ENGLISHFRENCHSPANISH
5°F 0°F 5°F(U.S.)
3°C 0°C 3°C(Canada)ONOFFIGN OFFTRIP AAUTOKMMILESONOFF60sec30secMAXHIGHMID
TRIP B
15sec
LOWMIN
Default setting:
Multi-Information Display
92
12/07/13 16:49:03 31TM8630_097
Instruments
andC
ontrols
TOC
2013 Insight
*
*
*
*
*
*
*
DescriptionMenu ItemGroup Setup PageSetting OptionChanges when the doors automatically lock.
Changes when the doors automatically unlock.
Changes which doors unlock with the remotetransmitter in a first push.The exterior lights flash each time you press theLOCK or UNLOCK button. A beeper will alsosound when you press the LOCK button twice.Changes how long it takes (in seconds) for thedoors to relock and the security system to set afteryou unlock but do not open the door.Set/Cancel all the customized settings as default.
AUTO DOOR LOCK
AUTO DOOR UNLOCK
DOOR LOCK MODE
KEYLESS LOCKACKNOWLEDGMENT
SECURITY RELOCKTIMER
DOOR SETUP(P.108)
DEFAULT ALL(P.117)
109
110
112
114
115
117
SHIFT FROM PWITH VEH SPDOFF
IGN OFFOFFDRIVER DOORALL DOORSONOFF
90sec60sec30secSETCANCEL
Default setting:
DRIVER DOOR /ALL DOORS
SHIFT TO P
Multi-Information Display
93
12/07/13 16:49:09 31TM8630_098
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
▲▼
▲ ▼
You can customize some of thevehicle control settings to yourpreference. Here are the settingsyou can customize:
METER SETUP
When you want to change thevehicle control settings, press theINFO ( / ) button to select CHGSETTING, then press the SEL/RESET button.
Each time you press the INFO ( /) button, the screen changes as
shown on the next page. Press theINFO ( / ) button until you seethe setup you want to customize,then press the SEL/RESET buttonto enter your selection.
If you do not make any changes,select ‘‘EXIT.’’ The display returns tothe normal display.
You can also use the select/resetknob in the instrument panel. Turnthe knob to select a setting and pressit to enter your selection.
If you want the settings as they werewhen the vehicle left the factory,select DEFAULT ALL, as describedon page .
LIGHTING SETUPDOOR SETUP
117
Customize Settings
Multi-Information Display
94
12/07/13 16:49:17 31TM8630_099
Instruments
andC
ontrols
TOC
2013 Insight
▼▲
▲ ▼
Multi-Information Display
95
NORMAL DISPLAY
U.S.
METER SETUPSee page 96
LIGHTING SETUPSee page 104
: Press the SEL/RESET button.
: Press the INFO button .
: Press the INFO button .
: Press and hold the INFO ( / ) button.
DOOR SETUPSee page 108
Canada
12/07/13 16:49:23 31TM8630_100
Instruments
andC
ontrols
TOC
2013 Insight
▲▼
▲ ▼
▼▲
LANGUAGE SELECTIONADJUST OUTSIDE TEMP.DISPLAY
Here are the four custom settingsfor the meter setup:
TRIP A RESET with REFUEL
Each time you press the INFO ( /) button, the screen changes as
shown in the illustration. Press theINFO ( / ) button until you seethe setting you want to customize,then press the SEL/RESET buttonto enter your selection.
While ‘‘METER SETUP’’ is shown,press the SEL/RESET button toenter the customize mode.
METER COLOR CHANGEDISPLAY KM/MILESELAPSED TIME RESET
Meter Setup
Multi-Information Display
96
: Press the SEL/RESET button.
: Press the INFO button .
: Press the INFO button .
See page 103 See page 101
See page 97 See page 98 See page 99 See page100
12/07/13 16:49:34 31TM8630_101
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
▲ ▼
Language Selection
There are three language selectionsyou can make: English, French, andSpanish. To choose the language youwant, follow these instructions:
You can choose this item tocustomize from ‘‘METER SETUP’’by pressing the INFO ( / ) buttonrepeatedly.
Press the SEL/RESET button to seethe selections.
Select the desired language bypressing the INFO ( / ) button,then enter your selection by pressingthe SEL/RESET button.
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘SETTING INCOMPLETE’’message appears, go back to‘‘LANGUAGE SELECTION’’ andrepeat the procedure again.
CONTINUED
Multi-Information Display
97
12/07/13 16:49:42 31TM8630_102
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
▲ ▼
Adjust Outside Temp. Display
If you sometimes find that thetemperature reading is a fewdegrees above or below the actualtemperature, you can adjust it byfollowing these instructions:
Adjust the outside temperature valueby pressing the INFO ( / ) buttonrepeatedly. Press the SEL/RESETbutton to set the desired value.
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘SETTING INCOMPLETE’’message appears, go back to‘‘ADJUST OUTSIDE TEMP.DISPLAY’’ and repeat theprocedure again.
You can choose this item tocustomize from ‘‘METER SETUP’’by pressing the INFO ( / ) buttonrepeatedly.Press the SEL/RESET button toenter the setting.
Multi-Information Display
98
Canadian models Canadian modelsU.S. modelsU.S. models
12/07/13 16:49:51 31TM8630_103
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
▲ ▼
Press the SEL/RESET button to seethe selections.
Select ON or OFF by pressing theINFO ( / ) button, then enteryour selection by pressing the SEL/RESET button.
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
To cause Trip A and average fuel fortrip A to reset every time you refuelyour vehicle, follow theseinstructions:
You can choose this item tocustomize from ‘‘METER SETUP’’by pressing the INFO ( / )button repeatedly.
If the ‘‘SETTING INCOMPLETE’’message appears, go back to ‘‘TRIPA RESET with REFUEL’’ and repeatthe procedure again.
Trip A Reset With Refuel
CONTINUED
Multi-Information Display
99
12/07/13 16:49:59 31TM8630_104
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
▲ ▼
-
-
-
Elapsed Time Reset
You can choose this item tocustomize from ‘‘METER SETUP’’by pressing the INFO ( / )button repeatedly.
Press the SEL/RESET button to seethe selections.
Select the desired setting bypressing the INFO ( / ) button,then enter your selection by pressingthe SEL/RESET button.
There are three elapsed time resetchoices you can make:
IGN OFF The elapsed time isreset when you turn the ignitionswitch to the LOCK (0) position.
TRIP A The elapsed time is resetwhen Trip A is reset.
TRIP B The elapsed time is resetwhen Trip B is reset.
Multi-Information Display
100
12/07/13 16:50:06 31TM8630_105
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘SETTING INCOMPLETE’’message appears, go back to‘‘ELAPSED TIME RESET’’ andrepeat the procedure again.
To change the displayedmeasurement in the trip computerand trip information and to switchbetween kilometers and miles, followthese instructions:
You can choose this item tocustomize from ‘‘METER SETUP’’by pressing the INFO ( / )button repeatedly.
CONTINUED
Multi-Information Display
Display Km/Miles
101
12/07/13 16:50:13 31TM8630_106
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
Press the SEL/RESET button to seethe selections.
Select AUTO, KM, or MILES bypressing the INFO ( / ) button,then enter your selection by pressingthe SEL/RESET button.
AUTO: When you press the km/milechange knob in the instrument panelto switch the speedometer readingbetween miles per hour (mph) andkilometers per hour (km/h), thedisplayed measurement in the tripcomputer and trip information, alsoswitches to kilometers or milesdepending on the selectedspeedometer reading.
KM: The displayed measurement inthe trip computer and tripinformation is set to kilometers.
MILES: The displayed measurementin the trip computer and tripinformation is set to miles.
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘DISPLAY KM/MILESSETTING INCOMPLETE’’message appears, go backto ‘‘DISPLAY KM/ MILES’’and repeat the procedure again.
Multi-Information Display
102
12/07/13 16:50:20 31TM8630_107
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
▲ ▼
You can turn the ambient meterfeature on or off (see page ).
You can choose this item tocustomize from ‘‘METER SETUP’’by pressing the INFO ( / )button repeatedly.
Press the SEL/RESET button to seethe selections.
Select ON or OFF by pressing theINFO ( / ) button, then enteryour selection by pressing the SEL/RESET button.
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘METER COLOR CHANGESETTING INCOMPLETE’’ messageappears, go back to ‘‘METERCOLOR CHANGE’’ and repeat theprocedure again.
72
Meter Color Change
Multi-Information Display
103
12/07/13 16:50:27 31TM8630_108
Instruments
andC
ontrols
TOC
2013 Insight
▲▼
▲ ▼
▼▲
There is one custom setting for thelighting setup:
Each time you press the INFO ( /) button, the screen changes as
shown in the illustration. Press theINFO ( / ) button until you seethe setting you want to customize,then press the SEL/RESET buttonto enter your selection.
While ‘‘LIGHTING SETUP’’ isshown, press the SEL/RESETbutton to enter the customize mode.
INTERIOR LIGHTDIMMING TIMEAUTO LIGHT SENSITIVITY
Lighting Setup
Multi-Information Display
104
: Press the SEL/RESET button.
: Press the INFO button .
: Press the INFO button .
See page105
See page106
12/07/13 16:50:35 31TM8630_109
Instruments
andC
ontrols
TOC
2013 Insight
▲▼
▲ ▼
Interior Light Dimming Time
Press the SEL/RESET button to seethe selections.
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘SETTING INCOMPLETE’’message appears, go back to‘‘INTERIOR LIGHT DIMMINGTIME’’ and repeat the procedure again.
The interior lights fade out when youclose all doors. To change how longthe lights stay on before they fadeout, follow these instructions:
You can choose this item tocustomize from ‘‘LIGHTINGSETUP’’ by pressing the INFO ( /
) button repeatedly.
Select the desired setting (15sec,30sec, or 60sec) by pressing theINFO ( / ) button, then enteryour selection by pressing the SEL/RESET button.
CONTINUED
Multi-Information Display
105
12/07/13 16:50:43 31TM8630_110
Instruments
andC
ontrols
TOC
2013 Insight
-
-
-
-
-
▲ ▼
▲ ▼
The headlights automatically comeon when the headlight switch is inthe AUTO position and the ambientlight reaches a changeable level. Youcan select the auto light sensitivityfrom the following five levels:MAXThe headlights come on when it isbright.
HIGHThe headlights come on when it issomewhat bright.
MIDThe headlights come on when it is asbright as sunset or sunrise.
LOWThe headlights come on when it issomewhat dark.
MINThe headlights come on when it isdark.
You can choose this item tocustomize from ‘‘LIGHTINGSETUP’’ by pressing the INFO( / ) button repeatedly.
Press the SEL/RESET button to seethe selections.
Select the desired setting (MAX,HIGH, MID, LOW or MIN) bypressing the INFO ( / ) button,then enter your selection by pressingthe SEL/RESET button.
Auto Light Sensitivity
Multi-Information Display
106
12/07/13 16:50:51 31TM8630_111
Instruments
andC
ontrols
TOC
2013 Insight
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘SETTING INCOMPLETE’’message appears, go back to ‘‘AUTOLIGHT SENSITIVITY’’ and repeatthe procedure again.
Multi-Information Display
107
12/07/13 16:50:56 31TM8630_112
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
▲ ▼
▲▼
AUTO DOOR LOCK
Here are the five custom settings forthe door setup:
While ‘‘DOOR SETUP’’ is shown,press the SEL/RESET button toenter the customize mode.
Each time you press the INFO( / ) button, the screen changes
the setting you want to customize,then press the SEL/RESET buttonto enter your selection.
KEYLESS LOCKACKNOWLEDGMENTSECURITY RELOCK TIMER
AUTO DOOR UNLOCKDOOR LOCK MODE
Door Setup
Multi-Information Display
108
: Press the INFO button .
: Press the INFO button .
: Press the SEL/RESET button.
See page109
See page110
See page112
See page115
See page114
12/07/13 16:51:05 31TM8630_113
Instruments
andC
ontrols
TOC
as shown in the illustration. Pressthe INFO ( / ) button until you see
2013 Insight
-
▲ ▼
▲ ▼
-
-
Auto Door LockThere are three settings you canchoose from:
SHIFT FROM PThe doors lock whenever you movethe shift lever out of Park.
Select the desired setting bypressing the INFO ( / ) button,then enter your selection by pressingthe SEL/RESET button.
You can choose this item tocustomize from ‘‘DOOR SETUP’’ bypressing the INFO ( / ) buttonrepeatedly.
Press the SEL/RESET button toenter the selecting mode.
WITH VEHICLE SPEEDThe doors lock when the vehiclespeed reaches about 10 mph (about16 km/h).
OFFThe auto door lock mode isdeactivated all the time.
CONTINUED
Multi-Information Display
109
12/07/13 16:51:14 31TM8630_114
Instruments
andC
ontrols
TOC
2013 Insight
-
-
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘SETTING INCOMPLETE’’message appears, go back to ‘‘AUTODOOR LOCK’’ and repeat theprocedure again.
There are five possible settings youcan choose from:
DRIVER DOOR WITH SHIFT TO PThe driver’s door unlocks when
you move the shift lever to Park withthe brake pedal depressed.
ALL DOORS WITH SHIFT TO PAll the doors unlock when you movethe shift lever to Park with the brakepedal depressed.
Auto Door Unlock
Multi-Information Display
110
12/07/13 16:51:19 31TM8630_115
Instruments
andC
ontrols
TOC
2013 Insight
-
-
▲ ▼
▲ ▼
-
DRIVER DOOR WITH IGN OFFThe driver’s door unlocks when youturn the ignition switch to the LOCK(0) position.
ALL DOORS WITH IGN OFF Allthe doors unlock when you turn theignition switch to the LOCK (0)position.
You can choose this item tocustomize from ‘‘DOOR SETUP’’by pressing the INFO ( / )button repeatedly.
Press the SEL/RESET button toenter the selecting mode.
Select the desired setting bypressing the INFO ( / ) button.
For example, you choose ‘‘DRIVERDOOR with SHIFT to P,’’ you willsee the above display.
OFF The auto door unlock isdeactivated all the time.
CONTINUED
Multi-Information Display
111
12/07/13 16:51:27 31TM8630_116
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
Press the SEL/RESET button toenter your selection.
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘SETTING INCOMPLETE’’message appears, go back to ‘‘AUTODOOR UNLOCK’’ and repeat theprocedure again.
To select whether the driver’s or alldoors unlock when you unlock thedoors with the remote transmitter orthe key, follow these instructions.
If you choose ‘‘ALLDOORS With IGN OFF,’’you will see the above display.
You can choose this item tocustomize from ‘‘DOOR SETUP’’by pressing the INFO ( / )button repeatedly.
Door Lock Mode
Multi-Information Display
112
12/07/13 16:51:35 31TM8630_117
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
Press the SEL/RESET button toenter the selecting mode.
Select the desired setting bypressing the INFO ( / ) button,then enter your selection by pressingthe SEL/RESET button.
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘SETTING INCOMPLETE’’message appears, go back to ‘‘DOORLOCK MODE’’ and repeat theprocedure again.
Multi-Information Display
113
12/07/13 16:51:40 31TM8630_118
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
▲ ▼
Press the SEL/RESET button toenter the selecting mode.
Select ON or OFF by pressing theINFO ( / ) button, then enteryour selection by pressing the SEL/RESET button.
You can choose this item tocustomize from ‘‘DOOR SETUP’’ bypressing the INFO ( / ) buttonrepeatedly.
When you push the LOCK button onthe remote transmitter, someexterior lights flash, and a beepersounds when you push the LOCKbutton again within 5 seconds toverify that the doors and the hatchare locked and the security systemhas set (see page ). You cancustomize the exterior lights not toflash and the beeper not to sound.
221
Keyless Lock Acknowledgment
Multi-Information Display
114
12/07/13 16:51:46 31TM8630_119
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
Security Relock Timer
You can change this relock timefrom 30 seconds to 60 or 90 seconds.
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
If the ‘‘SETTING INCOMPLETE’’message appears, go back to‘‘KEYLESS LOCKACKNOWLEDGMENT’’ and repeatthe procedure again.
You can choose this item tocustomize from ‘‘DOOR SETUP’’ bypressing the INFO ( / ) buttonrepeatedly.
If you unlock the doors with theremote transmitter, but do not openany of the doors within 30 seconds,the doors and the hatch,automatically relock, and thesecurity system sets.
CONTINUED
Multi-Information Display
115
12/07/13 16:51:53 31TM8630_120
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼
If the ‘‘SETTING INCOMPLETE’’message appears, go back to‘‘SECURITY RELOCK TIMER’’ andrepeat the procedure again.
When your selection is successfullycompleted, the display changes asshown above, and then goes back tothe customizable item screen.
Press the SEL/RESET button toenter the selecting mode.
Select the desired setting bypressing the INFO ( / ) button,then enter your selection by pressingthe SEL/RESET button.
Multi-Information Display
116
12/07/13 16:51:58 31TM8630_121
Instruments
andC
ontrols
TOC
2013 Insight
▲ ▼▲ ▼If you want to set the default settings,
press the INFO ( / ) button toselect DEFAULT ALL, then pressthe SEL/RESET button. If you want to cancel DEFAULT
ALL, select CANCEL, then press theSEL/RESET button. The screengoes back to the previous display.
To set the default settings, press theINFO ( / ) button to select SETthen press the SEL/RESET button.
When DEFAULT ALL is set, you willsee the above display for severalseconds, then the screen returns tothe default all setting display.
If the setting is not successfullycompleted, ‘‘FAILED’’ is shown forseveral seconds, and then thescreen goes back to SETUP. Repeatthe same procedure to selectDEFAULT ALL.
DEFAULT ALL
Multi-Information Display
117
12/07/13 16:52:05 31TM8630_122
Instruments
andC
ontrols
TOC
2013 Insight
***
*
*
*
*
*
*
*
*
*
To use the horn, press the center pad of the steering wheel.
Only on vehicles equipped with navigation system. Refer to the navigation system manual.If equipped
1 :2 :3 :
Controls Near the Steering Wheel
118
HORN
EX model with navigation system is shown.
HEADLIGHTS/TURN SIGNALS
REAR WINDOW DEFOGGER/HEATED MIRROR
ACCESSORY POWER SOCKET
MULTI-INFORMATIONBUTTONS (P.76)
MULTI-INFORMATION BUTTONS (P.76)
REMOTE AUDIOCONTROL BUTTONS
NAVIGATION SYSTEM VOICECONTROL BUTTONS
(P.119)(P.124)
CRUISE CONTROL BUTTONSINSTRUMENT PANEL BRIGHTNESS CONTROL KNOB WINDSHIELDWIPERS/WASHERS
MIRROR CONTROLS(P.147)
VEHICLE STABILITYASSIST (VSA) OFFSWITCH
STEERING WHEELADJUSTMENTS(P.128)
(P.126, P.148)
NAVIGATION SYSTEM /AUDIO SYSTEM
(P.120)
AUXILIARY INPUT JACK
(P.217)
(P.294)
BLUETOOTH HANDS-FREE LINKSYSTEM VOICE CONTROLBUTTONS (P.225)
(P.218)
(P.155)
(P.168)
(P.222)
1
2
2
2
2
3
2
3
2
12/07/13 16:52:13 31TM8630_123
Instruments
andC
ontrols
TOC
2013 Insight
-
-
-
-
-
-
-
-
-
Push the right lever up or down toselect a position.
The wipers run at highspeed until you release the lever.
The wipers are not activated.
The wipers run at low speed.
The wipers run at high speed.
Pull thewiper control lever toward you, andhold it. The washers spray until yourelease the lever. The wipers run atlow speed, then complete one moresweep after you release the lever.
MISTOFFINT IntermittentLO Low speedHI High speedWindshield washers
The length of the wipeinterval is varied automaticallyaccording to vehicle’s speed.
Vary the delay by turning theadjustment ring. If you turn it to theshortest delay ( position), thewipers change to low speedoperation when the vehicle speedexceeds 12 mph (20 km/h).
The length of the wiper interval isvaried automatically according to thevehicle’s speed.
1.2.3.4.5.6.
EX models
MIST
OFF
LO
HI
Windshield Washer
INT
Windshield Wipers and Washers
119
ADJUSTMENT RING
EX model is shown.
12/07/13 16:52:21 31TM8630_124
Instruments
andC
ontrols
TOC
2013 Insight
*
*
Rotate the switch counterclockwise also to spray the window washerand turn the wiper on.
Hold past ON to activate the rearwindow wiper a few times and tospray the rear window washer.
Rotate the switch clockwise toturn the rear window wiper ON.The wiper operates every 7seconds after completing
When you turn the wiper switch tothe ‘‘OFF’’ position, the wiper willreturn to its parked position.
OFF The rear window washer uses thesame fluid reservoir as the wind-shield washer.
When you shift the transmission tothe reverse position with the frontwindshield wiper activated, the rearwiper operates automatically even ifthe rear wiper switch is off.
Turn SignalOFFParking and interior lightsAUTOHeadlights onHigh BeamsFlash high beams
4.
3.
1.
2.
1.2.3.4.5.6.7.
: EX models
Rear Window Wiper and Washer Turn Signals and Headlights
Windshield Wipers and Washers, Turn Signals and Headlights
120
12/07/13 16:52:31 31TM8630_125
Instruments
andC
ontrols
TOC
two sweeps.
2013 Insight
- - -Push down on theleft lever to signal a left turn and upto signal a right turn. To signal a lanechange, push lightly on the lever andhold it. The lever will return to thecenter when you release it orcomplete a turn.
Turning the switch tothe ‘‘ ’’ position turns on theparking lights, taillights, instrumentpanel lights, side-marker lights, andrear license plate lights.
Turning the switch to the ‘‘ ’’position turns on the headlights.
When the light switch is in the‘‘ ’’ or ‘‘ ’’ position, thelights on indicator comes on as
This indicator stays on if you leavethe lights on and turn the ignitionswitch to the ACCESSORY (I) orLOCK (0) position.
If you leave the lights on with
switch, you will hear a reminderchime when you open thedriver’s door.
Push the left leverforward until you hear a click. Theblue high beam indicator will comeon (see page ). Pull the lever backto return to the low beams.
To flash the high beams, pull thelever back lightly, then release it.The high beams will stay on as longas you hold the lever back.
69
Turn Signal Headlights High Beams
Turn Signals and Headlights
121
12/07/13 16:52:38 31TM8630_126
Instruments
andC
ontrols
TOC
a reminder.
the key removed from the ignition
2013 Insight
-
The automatic lighting feature iscontrolled by a sensor located on topof the dashboard. Do not cover thissensor or spill liquids on it.
The automatic lightingfeature turns on the headlights, allother exterior lights, and theinstrument panel lights when itsenses low ambient light.
To turn on the automatic lighting,turn the light switch to the AUTOposition. The lights will come onautomatically when the outside lightlevel becomes low (at dusk, forexample). The lights on indicatorcomes on as a reminder. The lightsand indicator turn off automaticallywhen the system senses highambient light.
The lights turn off automaticallywhen you turn the ignition switch tothe LOCK (0) position. To turn themon again, either turn the ignitionswitch to the ON (II) position, orturn the light switch to the
position.
Even with the automatic lightingfeature turned on, we recommendthat you turn on the lights manually when driving at night orin a dense fog, or when you enterdark areas such as long tunnels orparking facilities.
To change the ‘‘AUTO LIGHTSENSITIVITY’’ setting, see
On EX modelsAUTO
Headlights
122
LIGHT SENSOR
12/07/13 16:52:44 31TM8630_127
Instruments
andC
ontrols
TOC
page 106 .
2013 Insight
With the headlight switch off or inthe position, the high beamheadlights and the high beamindicator come on with reducedbrightness when you turn theignition switch to the ON (II)position and release the parkingbrake. They remain on until you turnthe ignition switch off, even if youset the parking brake.
The headlights revert to normaloperation when you turn them onwith the switch.
If you see a ‘‘CHECK DRLSYSTEM’’ message on the multi-information display, there is aproblem with the daytime runninglight system. Take your vehicle to adealer to have it checked.
Daytime Running Lights
Headlights
123
12/07/13 16:52:49 31TM8630_128
Instruments
andC
ontrols
TOC
2013 Insight
To reduce glare at night, theinstrument panel illumination dimswhen you turn the light switch to the
or position. Turning theknob to the right until you hear atone will cancel the reducedbrightness.
The instrument panel will illuminate with reduced brightness when you unlock and open thedriver’s door. The brightness will increase slightly when you insertthe key in the ignition switch,then go to normal brightness when you turn the ignition switch to theON (II) position.
The knob on the instrument panelcontrols the brightness of theinstrument panel lights. Turn theknob to adjust the brightness withthe ignition switch in the ON (II)position and the parking lights on.
When you turn the knob, the multi-information display changes tovertical bars that show you thecurrent level.
You will hear a tone when you reachthe maximum or minimumbrightness. The brightness levelgoes out about 5 seconds after youstop adjusting.
Instrument Panel Brightness
124
INSTRUMENT PANEL BRIGHTNESSCONTROL KNOB BRIGHTNESS LEVEL
12/07/13 16:52:56 31TM8630_129
Instruments
andC
ontrols
TOC
2013 Insight
If you do not insert the key in theignition switch after opening thedriver’s door, the illumination turnsoff about 30 seconds after you closethe door.
If you insert the key but do not turnthe ignition switch to the ON (II)position, the illumination turns off inabout 10 seconds.
Push the button next to the audiosystem to turn on the hazardwarning lights (four-way flashers).This causes all four outside turnsignal lights and both turn signalindicators in the instrument panel toflash. Use the hazard warning lightsif you need to park in a dangerousarea near heavy traffic, or if yourvehicle is disabled.
Hazard Warning Button
Instrument Panel Brightness, Hazard Warning Button
125
HAZARD WARNING BUTTON
12/07/13 16:53:01 31TM8630_130
Instruments
andC
ontrols
TOC
2013 Insight
The defogger will shut itself offwithin about 10 to 30 minutesaccording to the outside temperature(over 32°F, 0°C).
Make sure all rear windows are clearand you have good visibility beforestarting to drive.
Pushing this button also turns themirror heaters on or off. For moreinformation, see page .
The defogger and antenna wires onthe inside of all rear windows can beaccidentally damaged. Whencleaning the glass, always wipe side-to-side.The rear window defogger will clear
fog, frost, and thin ice from thewindows. Push the defogger buttonto turn it on and off. The indicator inthe button comes on to show thedefogger is on. It also shuts off whenyou turn off the ignition switch. Youhave to turn the defogger on againwhen you restart the vehicle.
148
U.S. EX models and all Canadian models
Rear Window Defogger
126
U.S. EX model is shown.
12/07/13 16:53:06 31TM8630_131
Instruments
andC
ontrols
TOC
2013 Insight
Press the ECON button to activatethe ECON mode. ECON ON will bedisplayed on the multi-informationdisplay and the ECON modeindicator will illuminate in theinstrument panel. Press the ECONbutton again to turn it off. ECONOFF will appear on the multi-information display.
The ECON button turns the ECONmode on and off. The ECON modehelps you improve your fueleconomy by modifying somevehicle functions. When the ECONmode is on:
In addition, when the ECON mode ison, you may get more Eco Assistpoints (see page ).
The climate control system willhave greater temperaturefluctuations
Engine performance will bedifferent
When you turn off and then restartthe engine, the ECON mode settingremains the same as previously set.
264
ECON Button
127
MULTI-INFORMATION DISPLAY
ECON MODE INDICATOR
ECON BUTTON
12/07/13 16:53:12 31TM8630_132
Instruments
andC
ontrols
TOC
2013 Insight
Move the steering wheel so itpoints toward your chest, nottoward your face. Make sure youcan see the instrument panelgauges and indicators.
Make any steering wheeladjustments before you start driving.
Pull the lever under the steeringcolumn toward you until it stops.
Push the lever forward fully tolock the steering wheel in position.
Make sure you have securelylocked the steering wheel in placeby trying to move it up, down, in,and out.
Make sure the lever is positionedsecurely at the bottom of thesteering column as shown.
1.
3.
4.
2.
Steering Wheel Adjustments
128
To adjust
To lockLEVER
Adjusting the steering wheelposition while driving maycause you to lose control of thevehicle and be seriously injuredin a crash.
Adjust the steering wheel onlywhen the vehicle is stopped.
12/07/13 16:53:20 31TM8630_133
Instruments
andC
ontrols
TOC
2013 Insight
These keys contain electroniccircuits that are activated by theimmobilizer system. They will notwork to start the engine if thecircuits are damaged.
Protect the keys from directsunlight, high temperature, andhigh humidity.
Do not drop the keys or set heavyobjects on them.
Keep the keys away from liquids.If they get wet, dry themimmediately with a soft cloth.
Two ignition keys come with yourvehicle. You should keep one ofthem in a safe place, away from thevehicle, as a spare.
They fit all the locks on your vehicle.
You should have received a keynumber tag with your keys. You willneed this number if you ever have toget a lost key replaced. Use onlyHonda-approved key blanks.
Keys and Locks
129
KEYNUMBERTAG
IGNITION KEYSWITH REMOTETRANSMITTER
12/07/13 16:53:26 31TM8630_134
Instruments
andC
ontrols
TOC
2013 Insight
If the system repeatedly does notrecognize the coding of your key,contact your dealer.
Do not attempt to alter this systemor add other devices to it. Electricalproblems could result that may makeyour vehicle inoperable.
If you lose your key and you cannotstart the engine, contact your dealer.
The immobilizer system protectsyour vehicle from theft. If animproperly coded key (or otherdevice) is used, the engine’s fuelsystem is disabled.
When you turn the ignition switch tothe ON (II) position, the immobilizersystem indicator should come onbriefly, then go off. If the indicatorstarts to blink, it means the systemdoes not recognize the coding of thekey. Turn the ignition switch to theLOCK (0) position, remove the key,reinsert it, and turn the ignitionswitch to the ON (II) position again.
The system may not recognize yourkey’s coding if another immobilizerkey or other metal object (i.e. keychain) is near the ignition switchwhen you insert the key.
This device complies with theappropriate requirements or therequired standards. See page formore information.
392
Immobilizer System
130
Always take the ignition key with youwhenever you leave the vehicle alone.
12/07/13 16:53:33 31TM8630_135
Instruments
andC
ontrols
TOC
2013 Insight
--
The ignition switch has fourpositions: LOCK (0), ACCESSORY(I), ON (II), and START (III).
You canoperate the audio system and the accessory power sockets in this position.
If you leave the key in the ignitionswitch in the ACCESSORY (I)position and open the driver’s door,you will see a ‘‘RETURN IGNITIONSWITCH TO LOCK (0) POSITION’’message on the multi-informationdisplay and hear a reminder beeper.
If you turn the ignition key to theACCESSORY (I) position with thedriver’s door closed, you will see an‘‘ACCESSORY (I) POSITION’’message on the multi-informationdisplay to inform you of the keyposition.
You can insert orremove the key only in this position.To turn the key, the shift lever mustbe in Park, and you must push thekey in slightly.
If the front wheels are turned, theanti-theft lock may make it difficultto turn the key. Firmly turn thesteering wheel to the left or right asyou turn the key.
CONTINUED
ACCESSORY (I)LOCK (0)
Ignition Switch
131
12/07/13 16:53:40 31TM8630_136
Instruments
andC
ontrols
TOC
2013 Insight
-- Use this positiononly to start the engine. The switchreturns to the ON (II) position whenyou let go of the key.
You will hear a reminder beeper ifyou leave the key in the ignitionswitch in the LOCK (0) or theACCESSORY (I) position and openthe driver’s door. Remove the key toturn off the beeper.
You will also see a ‘‘REMOVE KEY’’message on the multi-informationdisplay.
The shift lever must be in Parkbefore you can remove the key fromthe ignition switch.
This is the normal keyposition when driving. Several of the indicators on the instrumentpanel come on as a test when you turn the ignition switch from the ACCESSORY (I) to theON (II) position.
START (III)ON (II)
Ignition Switch
132
12/07/13 16:53:44 31TM8630_137
Instruments
andC
ontrols
TOC
2013 Insight
When the door is unlocked, you cansee the red indicator on the lock tababove the inner door handle.
You can customize the door lock/unlock settings (see page ).
All doors and the hatch can belocked from the outside by using thekey in the driver’s door. To unlockonly the driver’s door, insert the key,turn it clockwise, and release it. Theremaining doors and the hatchunlock when you turn the key asecond time within a few seconds.
To lock all doors and the hatch, pushthe front of the master door lockswitch on the driver’s door, pull thelock tab rearward on the driver’sdoor, or use the key on the outsidelock on the driver’s door.
Pushing the rear of the master doorlock switch will unlock all doors andthe hatch. Pushing forward the locktab on the driver’s door unlocks onlythat door.
The lock tab on each passenger’sdoor locks and unlocks that door.
108
CONTINUED
Door Locks
133
Lock
Unlock
LOCK TABMASTER DOOR LOCK SWITCH
To unlock
To lock
12/07/13 16:53:52 31TM8630_138
Instruments
andC
ontrols
TOC
2013 Insight
The childproof door locks aredesigned to prevent children seatedin the rear from accidentally openingthe rear doors. Each rear door has alock lever near the edge. With thelever in the LOCK position (lever isdown), the door cannot be openedfrom the inside regardless of theposition of the lock tab. To open thedoor, push the lock tab forward anduse the outside door handle.
To lock any passenger’s door whengetting out of the vehicle, pull thelock tab rearward and close thedoor. To lock the driver’s door,remove the key from the ignition switch, pull the lock tab rearward orpush the front of the master switch,then close the door.
When the vehicle speed reachesabout 10 mph (U.S.)/15 km/h(Canada) or more, all the doors andthe hatch lock automatically.
When you shift to P after driving, thedriver’s door unlocks.
If you forget and leave the key in theignition switch, lockout preventionwill not allow you to lock the driver’sdoor. With any door or the hatchopen and the key in the ignitionswitch, locking with master doorlock switch is disabled. If the driver’sdoor is closed, the lock tab on thedriver’s door is not disabled. Pullingthe driver’s lock tab rearward willlock all doors and the hatch. If youtry to lock an open driver’s door bypulling the lock tab rearward, thedriver’s door lock tab pops out andunlocks the driver’s door.
Default setting
Lockout Prevention Childproof Door Locks
Door Locks
134
Unlock
Lock
LEVER
12/07/13 16:53:59 31TM8630_139
Instruments
andC
ontrols
TOC
2013 Insight
-
-
The ceiling light and the dooractivated spotlights come on whenyou press the UNLOCK button if thelights are in the door activatedposition. If you do not open any dooror the hatch within 30 seconds (orwhatever setting of the interior lightdimming time is set to), the light(s)will fade out. If you relock the doorsand the hatch with the remotetransmitter before 30 seconds haveelapsed, the light(s) will go offimmediately.
To change the lock/unlock settingand the relock timer setting, refer tothe customized settings on page .
The keyless lock acknowledgmentbeep and flashing of the lights canbe deactivated (see page ).
Press this button once tolock all doors and the hatch. Someexterior lights will flash once. Whenyou press LOCK twice within 5seconds, the horn will sounds toverify that the doors are locked. Youcannot lock the doors if any door orthe hatch is not fully closed or if thekey is in the ignition switch.
If you press the LOCK button twicewithin 5 seconds, you will hear ahorn to verify that the securitysystem has set.
Press this button onceto unlock the driver’s door (or all thedoors and the hatch depending onthe door lock setting). Press it twiceto unlock the remaining doors andthe hatch. Some exterior lights willflash twice when you press thebutton the first time.
If you do not open any door or thehatch within 30 seconds, they willautomatically relock, and thesecurity system (if equipped) willreset.
114
108
CONTINUED
On LX and EX models
LOCK
UNLOCK
Remote Transmitter
135
LED LOCK BUTTON
UNLOCKBUTTON
PANICBUTTON
12/07/13 16:54:07 31TM8630_140
Instruments
andC
ontrols
TOC
2013 Insight
-Avoid dropping or throwing thetransmitter.
Protect the transmitter fromextreme temperatures.
Do not immerse the transmitter inany liquid.
If you lose a transmitter, thereplacement needs to bereprogrammed by your dealer.
If it takes several pushes on thebutton to lock or unlock the doors,replace the battery as soon aspossible.
Battery type: CR1616
Press and hold thisbutton for about 1 second to attractattention; the horn will sound, andthe exterior lights will flash for about30 seconds. To cancel panic mode,press any other button on the remotetransmitter, or turn the ignitionswitch to the ON (II) position. Panicmode does not work when the key isin the ignition switch.
Remote Transmitter Care Replacingthe Transmitter Battery
PANIC
Remote Transmitter
136
12/07/13 16:54:14 31TM8630_141
Instruments
andC
ontrols
TOC
2013 Insight
+
Be careful when removing this screw as thehead of the screw can strip out.
Remove the screw at the base ofthe transmitter with a smallPhillips-head screwdriver.
Remove the old battery and notethe polarity. Make sure thepolarity of the new battery is thesame ( side facing down), theninsert it in the keypad.
To replace the battery:
Separate the keypad from thetransmitter by pushing any buttonfrom outside.
Place a cloth on the edge of thekeypad to prevent scratches, andremove the upper half by carefullyprying on the edge with a coin.
Snap the two halves of the keypad,then install the parts in reverseorder.
1.
2.
3. 4.
5.
CONTINUED
Remote Transmitter
137
NOTE:
SCREW
BATTERY
COIN
KEYPAD
12/07/13 16:54:24 31TM8630_142
Instruments
andC
ontrols
TOC
2013 Insight
An improperly disposed of batterycan hurt the environment.Always confirm local regulations forbattery disposal.
This device complies with theappropriate requirements or therequired standards. See page formore information.
392
Remote Transmitter
138
12/07/13 16:54:28 31TM8630_143
Instruments
andC
ontrols
TOC
2013 Insight
The hatch will lock or unlock whenyou lock/unlock the driver’s doorwith the key, the remote transmitter,the master door lock switch, or thelock tab on the driver’s door.
To unlock the hatch, turn the keyclockwise twice, push the rear ofthe master door lock switch, orpush UNLOCK twice on theremote transmitter.
Keep the hatch closed at all timeswhile driving to avoid damaging thehatch and to prevent exhaust gasfrom getting into the interior. See
onpage .
To open the hatch, push the release,and lift up. To close the hatch, usethe handle to lower it, then pressdown on the back edge.
56Carbon Monoxide Hazard
Hatch
139
INNER HANDLE
RELEASE
12/07/13 16:54:33 31TM8630_144
Instruments
andC
ontrols
TOC
2013 Insight
If the power door lock system cannotunlock the hatch, unlock it manually.
If you need to unlock the hatchmanually, it means there is aproblem with the hatch. Have thevehicle checked by your dealer.
Place a cloth on the top side of thecover to prevent scratches, then usea small flat-tip screwdriver to removethe cover on the back of the hatch.
Push the release lever to the lowerleft as shown, and push the hatch toopen it.
Unlocking the Hatch
Hatch
140
Unlock
COVER
RELEASE LEVER
12/07/13 16:54:39 31TM8630_145
Instruments
andC
ontrols
TOC
2013 Insight
-
The height of your driver’s seat isadjustable. To raise the seat,repeatedly pull up the lever on theoutside of the seat cushion. To lowerthe seat, push the lever downrepeatedly.
To change the seat-back angle of thefront seat, pull up the lever on theoutside of the seat bottom.
Once a seat is adjusted correctly,rock it back and forth to make sure itis locked in position.To adjust the seat forward or
backward, pull up on the bar underthe seat cushion’s front edge. Movethe seat to the desired position, andrelease the bar. Try to move the seatto make sure it is locked in position.
Make all adjustments before youstart driving.
See pages for important safetyinformation and warnings about how toproperly position seats and seat-backs.
14 15Driver’s Seat Height AdjustmentFront Seat Adjustments
Seats
141
12/07/13 16:54:48 31TM8630_146
Instruments
andC
ontrols
TOC
2013 Insight
See page for important safetyinformation and a warning aboutimproperly positioning head restraints.
16
Your vehicle is equipped with headrestraints in all seating positions tohelp protect you and yourpassengers from the likelihood ofwhiplash and other injuries.
They are most effective when youadjust them so the center of the backof the occupant’s head rests againstthe center of the restraint.
The front and rear outer headrestraints adjust for height. Youneed both hands to adjust therestraint. Do not attempt to adjust itwhile driving. To raise it, pull upward.To lower the restraint, push therelease button and push therestraint down.
Head Restraints
Adjusting the Head Restraint
Seats
142
LEGS SEAT-BACK
RELEASEBUTTON
Front Position CUSHION
12/07/13 16:54:55 31TM8630_147
Instruments
andC
ontrols
TOC
2013 Insight
To remove a head restraint forcleaning or repair, pull it up as far asit will go. Push the release button,then pull the restraint out of the seat-back.
When a passenger is seated in therear center seating position, thecenter head restraint should beadjusted up or down, to match thepassenger’s height.
The seat-back must be foldedforward (see page ) to get ceilingclearance for removal of the headrestraints.
145
CONTINUED
For Rear Seat Head Restraints
Removing the Head Restraint
Seats
143
LEGS SEAT-BACK SEAT-BACKLEGS
RELEASEBUTTON
Rear Outer Position Rear Center Position
CUSHION
RELEASEBUTTON
CUSHION
12/07/13 16:55:02 31TM8630_148
Instruments
andC
ontrols
TOC
2013 Insight
After a collision, the activatedrestraint should return to its normal position.
If the restraints do not return to theirnormal position, or in the event of asevere collision, have the vehicleinspected by a Honda dealer.
This reduces the distance betweenthe restraint and the occupant’s head.It also helps protect the occupants
against the likelihood of whiplashand injuries to the neckand upper spine.
The driver’s and front passenger’sseats have active head restraints. Ifthe vehicle is struck severely fromthe rear, the occupant properlysecured with the seat belt will bepushed against the seat-back and thehead restraint will automaticallymove forward.
Make sure the head restraint locksin position when you reinstall it.
When reinstalling a head restraint,put the legs back in place. Thenadjust it to the appropriate heightwhile pressing the release button.
Active Head Restraints
Seats
144
Failure to reinstall, or correctlyreinstall, the head restraints canresult in severe injury during acrash.
Always replace the headrestraints before driving.
12/07/13 16:55:09 31TM8630_149
Instruments
andC
ontrols
TOC
2013 Insight
Fold the seat-back forward.
Unlock the seat-back by pulling upthe release lever on the outer sideof each rear seat-back.
The rear seat-backs can be foldeddown for more cargo room.
Each side folds down separately, soyou can still carry one or twopassengers in the rear seat.
Remove any items from the seatbefore folding down the seat-back,and make sure there areno items on the floor beforefolding down the seats.
Lower the rear head restraints totheir lowest positions. If you folddown the right side seat-back, alsoadjust the rear center headrestraint to its lowest position.
For a head restraint system to workproperly:
Do not hang any items on the headrestraints, or from the restraintlegs.
Only use genuine Hondareplacement head restraints.
Install each restraint in its properlocation.
Do not place any object betweenan occupant and the seat-back.
Do not put any heavy items on theseat-back when it is folded down.
1.2.
3.
CONTINUED
Folding the Rear Seats Down
Seats
145
RED INDICATOR
LEVER
12/07/13 16:55:20 31TM8630_150
Instruments
andC
ontrols
TOC
2013 Insight
The lid of the console compartmentcan be used as an armrest.
Make sure all items in the cargo areaare secured. Loose items can flyforward and cause injury if you haveto brake hard (Seeon page ).
Reverse this procedure to return theseat-back to the upright position. Pullon the seat-back to make sure it islatched. If the seat-back is notlatched fully, the seat belt will notwork properly and you will see thered indicator behind the releaselever as shown on the previous page.
Make sure the seat-back and seatcushion are locked securely and allrear shoulder belts are positioned infront of the rear seat-backs.
256
U.S. LX and EX models
Armrest
Carrying Cargo
Seats
146
12/07/13 16:55:26 31TM8630_151
Instruments
andC
ontrols
TOC
2013 Insight
Keep the inside and outside mirrorsclean and adjusted for best visibility.Be sure to adjust the mirrors beforeyou start driving.
The inside mirror has day and nightpositions. The night position reduces glare from headlights behind you. Flip the tab on thebottom edge of the mirror to selectthe day or night position.
Move the selector switch to L(driver’s side) or R(passenger’s side).
Turn the ignition switch to the ON(II) position.
Push the appropriate edge of theadjustment switch to move themirror right, left, up, or down.
When you finish, move theselector switch to the center (off)position. This turns theadjustment switch off to keep \
1.
2.
3.
4.
Adjusting the Power Mirrors
Mirrors
147
SELECTORSWITCH
ADJUSTMENTSWITCH
TAB
UP
DOWN
Night PositionDaytime Position
12/07/13 16:55:33 31TM8630_152
Instruments
andC
ontrols
TOC
your settings.
2013 Insight
The outside mirrors are heated toremove fog and frost. With theignition switch in the ON (II)position, turn on the heaters bypressing the rear window defoggerbutton. The indicator in the buttoncomes on as a reminder. Press thebutton again to turn the heaters andthe defogger off.
This heated mirror function has atimer (see page ).126
On U.S. EX models and all Canadian models
Power Mirror Heaters
Mirrors
148
HEATED MIRROR BUTTON
12/07/13 16:55:38 31TM8630_153
Instruments
andC
ontrols
TOC
2013 Insight
-
Turn the ignition switch to the ON(II) position to raise or lower anywindow. To open a window, push theswitch down and hold it. Release theswitch when you want the window tostop. Pull back on the switch andhold it to close the window.
To open or close thedriver’s window, push or pull thewindow switch firmly down or up tothe second detent, and release it.The window will automatically godown or up all the way. To stop thewindow, pull or push the windowswitch briefly.
CONTINUED
AUTO
Power Windows
149
DRIVER’SWINDOWSWITCH
FRONTPASSENGER’SWINDOW SWITCH
MAIN SWITCH
Closing a power window onsomeone’s hands or fingers cancause serious injury.
Make sure your passengers areaway from the windows beforeclosing them.
12/07/13 16:55:43 31TM8630_154
Instruments
andC
ontrols
TOC
2013 Insight
-
Auto reverse stops sensing when thewindow is almost closed. You shouldalways check that all passengers andobjects are away from the windowbefore closing it.
The driver’s window autoreverse function is disabled whenyou continuously pull up the switch.
If the driver’swindow senses any obstacle while itis closing automatically, it willreverse direction, and then stop. Toclose the window, remove theobstacle, then use the windowswitch again.
The windows and the main switchfeature will operate for up to 10minutes after you turn off theignition switch. Opening either frontdoor cancels this function.
When you push the main switch in,the indicator comes on and thepassengers’ windows cannot beraised or lowered. Use the mainswitch when you have children in thevehicle so they do not injurethemselves by operating thewindows unintentionally. To cancelthis feature, push on the switchagain. The switch will pop out.
AUTO REVERSE
Power Windows
150
NOTE:
12/07/13 16:55:48 31TM8630_155
Instruments
andC
ontrols
TOC
2013 Insight
To apply the parking brake, pull thelever up fully. To release it, pull upslightly, push the button, and lowerthe lever. The parking brakeindicator on the instrument panelshould go out when the parkingbrake is fully released (see page ).
If you drive without releasing theparking brake, a beeper will sound,and you will also see a ‘‘RELEASEPARKING BRAKE’’ message on themulti-information display.
63
Parking Brake
151
PARKING BRAKE LEVER
EX model is shown.
Driving the vehicle with the parkingbrake applied can damage the rearbrakes and hubs. A beeper will sound ifthe vehicle is put into gear with theparking brake on.
12/07/13 16:55:53 31TM8630_156
Instruments
andC
ontrols
TOC
2013 Insight
* *
*
*
* *
*
Interior Convenience Items
152
FRONT DOORPOCKET
CENTER CONSOLECOMPARTMENT
FLOOR STORAGECOMPARTMENT
CARGO AREA
: If equipped
EX model with navigation system is shown.
AUXILIARY INPUT JACK/ACCESSORY POWERSOCKET
UNDER FLOORSTORAGE
GLOVE BOX
BEVERAGE HOLDERS
CENTER TRAY /CENTER POCKET
SEAT-BACKPOCKETS
REAR DOOR BEVERAGE HOLDER
COAT HOOK USB ADAPTER CABLE VANITY MIRROR
CENTER POCKET
SUN VISOR
12/07/13 16:55:58 31TM8630_157
Instruments
andC
ontrols
TOC
2013 Insight
To open the cargo floor, fold thecargo floor forward.
To use the storage compartmentlocated on the left side of the cargoarea floor, hold the strap and raisethe lid.
Close the lid by pressing until itlatches.
Interior Convenience Items
Under Floor Storage Floor Storage Compartments
153
STRAP
LID
CARGO FLOORSTORAGE
12/07/13 16:56:04 31TM8630_158
Instruments
andC
ontrols
TOC
2013 Insight
Spilled liquids can damage theupholstery, carpeting, and electricalcomponents in the interior.
Be careful when you are using thebeverage holders. A spilled liquidthat is very hot can scald you or yourpassengers. Liquid can also spillfrom the front and rear door pocketbeverage holders when you open orclose the doors. Use only resealablecontainers in the door pockets.
Beverage Holders
Interior Convenience Items
154
FRONT REAR
BEVERAGE HOLDERS
Insight model and Canadian LX model
FRONT
BEVERAGEHOLDERS
Insight model and LX model
EX model
BEVERAGEHOLDERS
12/07/13 16:56:11 31TM8630_159
Instruments
andC
ontrols
TOC
2013 Insight
Your vehicle has an accessory powersocket in the front console panel.
To use an accessory power socket,the ignition switch must be in theACCESSORY (I) or ON (II) position.
This socket is intended to supplypower for 12 volt DC accessoriesthat are rated 120 watts or less (10 amps).
It will not power an automotive typecigarette lighter element.
Make sure to put the socket coverback in place to prevent any smallforeign objects from getting into the socket.
To open the console compartment,pull up on the lever and lift thearmrest.
To close, lower the armrest, andpush it down until it latches.
On EX and U.S. LX models
Interior Convenience Items
Accessory Power Socket Console Compartment
155
LEVER
12/07/13 16:56:19 31TM8630_160
Instruments
andC
ontrols
TOC
2013 Insight
There is a tray in the front of thecenter console. You can also take thepartition out to extend the tray.
When you use the front beverageholders, you need to put the partitionback to the original position on thecenter console.
Open the glove box by pulling thehandle to the left. Close it with afirm push.
The glove box light comes on whenthe parking lights are on.
On EX models only
Center TrayGlove Box
Interior Convenience Items
156
PARTITIONAn open glove box can causeserious injury to your passengerin a crash, even if thepassenger is wearing the seatbelt.
Always keep the glove boxclosed while driving.
12/07/13 16:56:26 31TM8630_161
Instruments
andC
ontrols
TOC
2013 Insight
To open the center pocket, push onthe knob. To close it, push the lid upuntil it latches.
To open the center pocket, press therelease button. The lid will unlatchand swing up. To close it, push thelid down until it latches.
On EX modelsOn all models
Interior Convenience Items
Center Pockets
157
KNOB
Push
LID
12/07/13 16:56:32 31TM8630_162
Instruments
andC
ontrols
TOC
2013 Insight
To use the vanity mirror on the backof the sun visor, pull up the cover.
To use the sun visor, pull it down.You can also use the sun visor at theside window. Remove the supportrod from the clip and swing the sunvisor toward the side window.
Make sure you put the sun visorback in place when you are gettinginto or out of the vehicle.
To use a coat hook, slide it outslightly, then pull it down.
Make sure the coat hook is pulled up when you are not using it.This hook is not designed for largeor heavy items.
On U.S. EX models and Canadian models
Vanity MirrorSun VisorsCoat Hook
Interior Convenience Items
158
COAT HOOK
EX model is shown.
12/07/13 16:56:40 31TM8630_163
Instruments
andC
ontrols
TOC
2013 Insight
The ceiling light has a three-positionswitch: ON, Door Activated, andOFF. In the Door Activated (center)position, the light comes on whenyou:
After all doors are closed tightly, thelight dims slightly, then fades out inabout 30 seconds.
The ceiling light (with the switch inthe center position) comes on whenyou remove the key from the ignitionswitch. If you do not open a door, thelight stays on, then fades out inabout 30 seconds.
Turn on a spotlight by pushing thelens. Push the lens again to turn itoff. You can use the spotlights at
Unlock the driver’s door with thekey or remote transmitter.
Open any door.
To change the ‘‘INTERIOR LIGHTDIMMING TIME’’ setting, seepage .
If you leave any door open withoutthe key in the ignition switch, theceiling light will go off after about15 minutes.
105
CONTINUED
Ceiling Light Spotlights
Interior Lights
159
DOOR ACTIVATED POSITION
EX model with navigation system
Push
Push
SPOTLIGHTS
12/07/13 16:56:50 31TM8630_164
Instruments
andC
ontrols
TOC
all times.
2013 Insight
Your vehicle has a cargo area lighton the left side panel of the cargoarea. It comes on when you open the hatch.
Cargo Area Light
Interior Lights
160
Push
CARGO AREA LIGHT
Push
SPOTLIGHTS
U.S. LX model
12/07/13 16:56:55 31TM8630_165
Instruments
andC
ontrols
TOC
2013 Insight
The climate control system in yourvehicle provides a comfortabledriving environment in all weather conditions.
The standard audio system hasmany features. This sectiondescribes those features and how touse them.
Your vehicle has an anti-theft audiosystem that requires a code numberto enable it.
The security system helps to discourage vandalism and theft of your vehicle.
...............Climate Control System . 162................................Audio System . 168
..........Playing the AM/FM Radio . 169................................Playing a Disc . 173
.......Disc Player Error Messages . 180
..........Playing the FM/AM Radio . 181................................Playing a Disc . 188
.......Disc Player Error Messages . 194............................Playing an iPod . 195
.................iPod Error Messages . 201Playing a USB Flash Memory
........................................Device . 202USB Flash Memory Device Error
...................................Messages . 211............FM/AM Radio Reception . 212
..................Protecting Your Discs . 214................Remote Audio Controls . 217
......................Auxiliary Input Jack . 218.................Radio Theft Protection . 219
..........................Setting the Clock . 220............................Security System . 221
...............................Cruise Control . 222........HandsFreeLink . 225
Insight model
LX model and EX model withoutnavigation system
Bluetooth
Features
Features
161
12/07/13 16:57:00 31TM8630_166
2013 Insight
Climate Control System
162
TEMPERATURE CONTROL DIAL
AIR CONDITIONING BUTTON
RECIRCULATION BUTTON
FRESH AIR BUTTON
WINDSHIELDDEFROST BUTTON
REAR WINDOW DEFOGGER/HEATED MIRRORS BUTTON
REAR WINDOWDEFOGGER BUTTON
MODE CONTROL BUTTON
FAN CONTROL BAR
U.S. EX model and Canadian models
ON/OFF BUTTON
12/07/13 16:57:04 31TM8630_167
Features
TOC
2013 Insight
CONTINUED
On models with navigation system The automatic climate controlsystem in your vehicle maintains theinterior temperature you select. Thesystem also adjusts the fan speedand airflow levels.
The climate control system for yourvehicle can also be operated usingthe voice control system. See thenavigation system manual forcomplete details. Press the AUTO button. You will
see AUTO in the display.
Set the desired temperature by turning the temperaturecontrol dial.
The system automatically selectsthe proper mix of conditionedand/or heated air that will, asquickly as possible, raise or lower the interior temperatureto your preference.
During the auto idle stop, the airconditioning system will be turnedoff. If the ECON mode is selected,the fan may also be turned off.
Turning this dial clockwise increasesthe temperature of the airflow.
2.
1.
Voice Control System Using Automatic Climate Control
Climate Control System
Temperature Control
163
12/07/13 16:57:13 31TM8630_168
Features
TOC
2013 Insight
▲
▼
When you set the temperature to itslower limit ( ) or its upper limit( ), the system runs at fullcooling or heating only. It does notregulate the interior temperature.
When you adjust a fan control, thefan is taken out of AUTO mode.
Press the side of the bar toincrease the fan speed and airflow.Press the side of the bar todecrease them.
You can manually select variousfunctions of the climate controlsystem when it is in fully automaticmode. All other features remainautomatically controlled. Making anymanual selection causes the wordAUTO in the display to go out.
To keep stale air and mustinessfrom collecting, you should havethe fan running at all times.
Keep the system completely offfor short periods only.
To turn the system completely off,press the ON/OFF button.
Each time you press this button, theclimate control system switchesbetween on and off. Turning on thesystem with this button selects yourlast climate control selection.
Climate Control System
Semi-automatic Operation
Fan Control
To Turn Everything Off
ON/OFF Button
164
12/07/13 16:57:23 31TM8630_169
Features
TOC
2013 Insight
CONTINUED
This button turns the airconditioning on and off. You will seeA/C ON or A/C OFF in the display.
When you turn the A/C off, thesystem cannot regulate the insidetemperature if you set thetemperature control below theoutside temperature.
Pushing this button also turns thepower mirror heaters on and off.
When the recirculation indicator ison, air from the vehicle’s interior issent throughout the system again.
Select recirculation mode whendriving through dusty or smokyconditions, then return to fresh air mode.
The outside air intakes for theclimate control system are at thebase of the windshield. Keep thisarea clear of leaves and other debris.
When the fresh air indicator is on,air is brought in from the outside ofthe vehicle.
The system should be left in freshair mode under almost all conditions.Keeping the system in recirculationmode, particularly with the A/C off,can cause the windows to fog up.
This button turns the rear windowdefogger on and off (see page ).126
On U.S. EX models and all Canadian models
Climate Control System
Air Conditioning (A/C) Button Recirculation Button Rear Window Defogger Button
Fresh Air Button
165
12/07/13 16:57:35 31TM8630_170
Features
TOC
2013 Insight
To remove fog from the inside of thewindows, set as follows:Use the mode control button to
select the vents the air flows from.Some air will flow from thedashboard vents in all modes.
Airflow is divided betweenthe floor and corner vents and thedefroster vents at the base of thewindshield.
This button directs the main airflowto the windshield for fasterdefrosting. It also overrides anymode selection you may have made.
Select . The systemautomatically switches to fresh airmode and turns on the A/C.Adjust the temperature so theairflow feels warm.Select to help clear therear window.To increase airflow to thewindshield, close the corner vents.For faster defogging, manually setthe fan speed to high.
For your safety, make sure you havea clear view through all the windowsbefore driving.
When you select , the systemautomatically switches to fresh airmode and turns on the A/C. Forfaster defrosting, manually set thefan speed to high. You can alsoincrease airflow to the windshield by closing the corner vents on the dashboard.
When you turn off bypressing the button again, thesystem returns to its former settings.
Air flows from the floorvents.
Airflow is divided betweenthe vents in the dashboard and thefloor vents.
Air flows from the centerand corner vents in the dashboard.
1.
2.
3.
4.
Climate Control System
Mode Control Windshield Defroster Button
166
12/07/13 16:57:47 31TM8630_171
Features
TOC
2013 Insight
To regulate the interior temperatureand humidity, the climate controlsystem has two sensors. A sunlightsensor is located in the top of thedashboard and a temperature/humidity sensor is next to thesteering column. Do not cover thesensors or spill any liquid on them.
Climate Control System
Sunlight, Temperature, andHumidity Sensors
167
TEMPERATURE/HUMIDITY SENSOR
SUNLIGHT SENSOR
SUNLIGHT SENSOREX models
Insight model and LX model
12/07/13 16:57:53 31TM8630_172
Features
TOC
2013 Insight
An audio system is standard on allmodels. Read the appropriate pages(as shown below) to use yourvehicle’s audio system.
For LX and EX models withoutnavigation system, see pages
through .
For Insight model, see pagesthrough .
For EX model with navigationsystem, see navigation systemmanual for how to operate the audiosystem.
169 180
181 211
Audio System
168
Insight model LX and EX models withoutnavigation system
12/07/13 16:58:00 31TM8630_173
Features
TOC
2013 Insight
Playing the AM/FM Radio (Insight model)
169
AMBUTTON
FMBUTTON
PRESET BUTTONS
POWER/VOLUMEKNOB
SEEK/SKIP BAR
TUNE KNOB
A.SEL/SCANBAR
12/07/13 16:58:04 31TM8630_174
Features
TOC
2013 Insight
-
-
-
You can use any of five methods tofind radio stations on the selectedband: tune, seek, scan, the presetbuttons, and auto select.
Use the TUNE knob totune the radio to a desired frequency.Turn the knob to the right to tune toa higher frequency, and turn it to theleft to tune to a lower frequency.
The ignition switch must be in theACCESSORY (I) or ON (II) position.Turn the system on by pushing thepower/volume knob or the AM orFM button. Adjust the volume byturning the power/volume knob.
The scan function samplesall stations with strong signals on theselected band. To activate it, pressthe right side of the A. SEL/SCANbar, then release it. You will seeSCAN in the display. The system willscan for a station with a strong signal.When it finds one, it will stop andplay that station for about 10 seconds.
If you do nothing, the system willthen scan for the next strong stationand play it for 10 seconds. When itplays a station you want to listen to,press the SCAN side of the bar again.
The band and frequency that theradio was last tuned to is displayed.To change bands, press the AM orFM button. On the FM band, ST willbe displayed if the station is broad-casting in stereo. Stereoreproduction on AM is not available.
The seek functionsearches up and down from thecurrent frequency to find a stationwith a strong signal. To activate it,press the or side of theSEEK bar, then release it.
To Select a Station
TUNE
To Play the AM/FM Radio SCAN
SEEK/SKIP
Playing the AM/FM Radio (Insight model)
170
12/07/13 16:58:11 31TM8630_175
Features
TOC
2013 Insight
- -
-
If you do not like the stations autoselect has stored, you can storeother frequencies on the presetbuttons as previously described.
For information on AM/FM radiofrequencies and reception, see
.
Each preset button canstore one frequency on AM and twofrequencies on FM.
Select the desired band, AM orFM. You can store one frequencyon FM1, and one frequency onFM2 with each preset button.
Use the tune, seek, or scanfunction to tune the radio to adesired station.
, press theA. SEL side of the bar. This restoresthe presets you originally set.
Press the left side of theA. SEL/SCAN bar. You will seeA. SEL flashing in the display, andthe system goes into scan mode forseveral seconds. It stores thefrequencies of six AM, and twelveFM stations in the preset buttons.
You will see a ‘‘0’’ displayed afterpressing a preset button if autoselect cannot find a strong station forevery preset button.
If you aretraveling and can no longer receiveyour preset stations, you can use theauto select feature to find stations inthe local area.
Pick a preset button (1 6), thenpress and hold it until you hear abeep.
Repeat steps 1 through 3 to store atotal of six stations on AM andtwelve stations on FM.
1.
2.
3.
4.
To turn off auto select
Preset AUTO SELECT
Playing the AM/FM Radio (Insight model)
171
12/07/13 16:58:20 31TM8630_176
Features
TOC
page 212
2013 Insight
-
-
-
-
-
Adjusts the volume levelbased on the vehicle speed.Press the SOUND (TUNE) knob
repeatedly to display the BASS,TREBLE, FADER, BALANCE, andSVC (speed-sensitive volumecompensation) settings.
Each mode is shown in the display asit changes. Turn the TUNE knob toadjust the setting to your liking.
When the level reaches the center,you will see ‘‘C’’ in the display.
Adjusts the bass.
Adjusts the treble.
Adjusts the front-to-backstrength of the sound.
Adjusts the side-to-side strength of the sound.
The SVC has four modes: SVC OFF,SVC LOW, SVC MID, and SVCHIGH. Turn the TUNE knob toadjust the setting to your liking. Ifyou feel the sound is too loud,choose low. If you feel the sound istoo quiet, choose high.
The SVC mode controls the volumebased on vehicle speed. The fasteryou go, the louder the audio volumebecomes. As you slow down, theaudio volume decreases.
You can use the instrument panelbrightness control knob to adjust theillumination of the audio system (seepage ). The audio systemilluminates when the parking lightsare on, even if the radio is turned off.
Wait a few seconds and the displayreturns to normal.
Except SVC adjustment
124
Adjusting the Sound SVC
BASS
TREBLE
FADER
BALANCE
Audio System Lighting
Playing the AM/FM Radio (Insight model)
Speed-sensitive VolumeCompensation (SVC)
172
12/07/13 16:58:31 31TM8630_177
Features
TOC
2013 Insight
Playing a Disc (Insight model)
173
REPEAT BUTTONEJECTBUTTON
RANDOM BUTTON
A.SEL/SCANBAR
CD/AUXBUTTON
TUNE KNOB
LOADINDICATOR
DISP BUTTONSEEK/SKIP BAR
POWER/VOLUMEKNOB
12/07/13 16:58:36 31TM8630_178
Features
TOC
2013 Insight
You operate the disc player with thesame controls used for the radio. Toselect the disc player, press the CD/AUX button. You will see ‘‘CD’’in the display.
To load or play a disc, the ignitionswitch must be in the ACCESSORY(I) or ON (II) position.
This audio system can also playCD-Rs and CD-RWs compressed inMP3 or WMA formats. Whenplaying a disc in MP3, you will see‘‘MP3’’ in the display. In WMAformat, ‘‘WMA’’ will appear in thedisplay. You can select up to 99folders, or up to 255 tracks/files.
If a file on an MP3 or WMA disc isprotected by digital rightsmanagement (DRM), the audio unitdisplays FORMAT, and then skips tothe next file.
Video CDs and DVDs do not work inthis unit.
Depending on the software the fileswere made with, it may not bepossible to play some files, or displaysome text data.
To Play a Disc
Playing a Disc (Insight model)
174
NOTE:
Do not use discs with adhesive labels.The label can curl up and cause thedisc to jam in the unit.
12/07/13 16:58:42 31TM8630_179
Features
TOC
2013 Insight
>
CONTINUED
Insert a disc about halfway into thedisc slot. The drive will pull the discin the rest of the way to play it. Youoperate the disc player with thesame controls used for the radio.The number of the current track isshown in the display. When playing adisc in MP3 or WMA, the numbersof the current folder and file areshown. The system will continuouslyplay a disc until you change modes.
You cannot load and play 3-inch(8-cm) discs in this system.
Each time you press the DISP button,the display shows you the text dataon a disc, if the disc was recordedwith text data.
You can see the album, artist, andtrack name in the display. If a disc isrecorded in MP3 or WMA, you cansee the folder and file name, and thealbum, artist, and track tag.
With the folder name, you will seethe FOLDER indicator in the display.The TRACK indicator is shown withthe file or track name.
The display shows up to 10characters of selected text data (thefolder name, file name, etc.). If thetext data has more than 10characters, you will see the first 9characters and the indicator inthe display. Press and hold the DISPbutton until the next 10 charactersare shown.
Playing a Disc (Insight model)
To Load a Disc Text Data Display Function
175
12/07/13 16:58:49 31TM8630_180
Features
TOC
2013 Insight
- Each time youpress and release the side ofthe SEEK/SKIP bar, the player skipsforward to the beginning of the nexttrack (file in MP3 or WMA mode).Press and release the side, toskip backward to the beginning ofthe current track. Press it again toskip to the beginning of the \
To move rapidly within a track, pressand hold the or side of theSEEK/SKIP bar.
You can use the SEEK/SKIP barwhile a disc is playing to selectpassages and change tracks (files inMP3/WMA mode).
When playing a CD-DA with textdata, the album and track name areshown in the display. With a disc inMP3 or WMA, the display shows thefolder and file name.
You will also see some text dataunder these conditions:
When a new folder, file, or trackis selected.
When you change the audio modeto play a disc with text data or inMP3 or WMA.
When you insert a disc, and thesystem begins to play.
To Change or Select Tracks/Files
SEEK/SKIP
Playing a Disc (Insight model)
176
12/07/13 16:58:57 31TM8630_181
Features
TOC
previous track.
2013 Insight
-
-
--Toselect a different folder, turn theTUNE knob to move to thebeginning of the next folder. Turnthe knob to the right to skip to thenext folder, and to the left to move tothe beginning of the current folder.Turn it again to skip to the beginningof the previous folder. Turning theTUNE knob more than one clickskips several folders at a time.
To continuously replaya track (files in MP3 or WMA mode),press and release the RPT button.You will see ‘‘RPT’’ in the display.Press and hold the RPT button for 2seconds to turn it off.
This feature plays thetracks within a disc (the files in MP3or WMA mode) in random order. Toactivate random play, press andrelease the RDM button. In MP3 orWMA mode, press the RDM buttonrepeatedly to select RDM (within adisc random play). You will see‘‘RDM’’ in the display. Press theRDM button for 2 seconds to returnto normal play.
This feature,when activated, replays all files inthe selected folder in the order theyare compressed. To activate folderrepeat, press the RPT button twice.You will see F-RPT in the display.The system continuously replays thecurrent folder. Press the RPT buttonagain to turn it off. Pressing theRDM button, or selecting a differentfolder with the TUNE knob alsoturns off the repeat feature.
Each time you press and release theRPT button, the mode changes fromfile repeat to folder repeat, then tonormal play.
In MP3 or WMA mode In MP3 or WMA mode
CONTINUED
FOLDER SELECTION
REPEAT (TRACK/FILEREPEAT)
RANDOM (Random within adisc)FOLDER-REPEAT
Playing a Disc (Insight model)
177
12/07/13 16:59:03 31TM8630_182
Features
TOC
2013 Insight
--
-In MP3 or WMA modeIn MP3 or WMA mode
Thisfeature, when activated, samples thefirst file of each folder on the disc.To activate folder scan, press theSCAN bar twice. You will seeF-SCAN in the display.
The system plays the first file in thefirst folder for about 10 seconds. Ifyou do nothing, the system will thenplay the first files in the next foldersfor 10 seconds. After playing the firstfile in the last folder, the systemplays normally.
Pressing either side of the SEEK/SKIP bar, selecting a different folderwith the TUNE knob, or pressing theSCAN bar, also turns off folder scan.
The scan function samples all tracks(files in MP3 or WMA) on the disc inthe order they are recorded on thedisc. To activate scan, press andrelease the SCAN bar. You will seeSCAN in the display. You will get a10 second sampling of each track/file on the disc. Press and hold theSCAN button for about 2 seconds toget out of scan mode and play thelast track/file sampled.
Pressing either side of the SEEK/ SKIP bar also turns offthe scan feature.
Each time you press and releasethe SCAN bar, the modechanges from scan to folder scan,then to normal play.
Thisfeature, when activated, plays allfiles on the selected folderin random order. To activate folderrandom, press the RDM button.You will see F-RDM in the display.The system will then select and playfiles randomly. This continues until you deactivate folder random bypressing and holding theRDM button for 2 seconds.
Each time you press and release theRDM button, the mode changesfrom folder random play to randomplay (within a disc random play),then to normal play.
F-SCAN (FOLDER SCAN)SCAN (TRACK/FILE SCAN)
FOLDER-RANDOM
Playing a Disc (Insight model)
178
12/07/13 16:59:11 31TM8630_183
Features
TOC
2013 Insight
If you turn the system off while adisc is playing, either with thepower/volume knob or by turningoff the ignition switch, the disc willstay in the drive. When you turn thesystem back on, the disc will beginplaying where it left off.
For information on how to handleand protect compact discs, seepage .
Press the eject button ( ) toremove the disc. If you eject the disc,but do not remove it from the slot,the system will automatically reloadthe disc after 10 seconds and put it inpause mode. To begin playing, pressthe CD/AUX button.
You can also eject the disc when theignition switch is off.
To play the radio when a disc isplaying, press the AM or FM button.Press the CD/AUX button again toswitch back to the disc player.
214
Protecting Discs
To Stop Playing a Disc
Playing a Disc (Insight model)
179
12/07/13 16:59:17 31TM8630_184
Features
TOC
2013 Insight
The ejected disc will not be reloaded automatically.
If you see an error message in thedisplay while playing a disc, find thecause in the chart to the right. If youcannot clear the error message, takeyour vehicle to your dealer.The chart on the right explains theerror messages you may see in thedisplay while playing a disc.If you see an error message in thedisplay while playing a disc, pressthe eject button. After ejecting thedisc, check it for damage ordeformation. If there is no damage,insert the disc again.For additional information ondamaged discs, see page .
The audio system will try to play thedisc. If there is still a problem, theerror message will reappear. Pressthe eject button, and pull out the disc.Insert a different disc. If the newdisc plays, there is a problem withthe first disc. If the error messagecycle repeats and you cannot clear it,take your vehicle to a dealer.
CauseError Message Solution
215
Track/File format notsupported
Mechanical Error
Servo Error
Current track will be skipped. The nextsupported track or file plays automatically.Press the eject button and pull out the disc.Check the disc for serious damage, signs ofdeformation, excessive scratches, and/or dirtsee page 215. Insert the disc again. If the codedoes not disappear, or the disc cannot beremoved, consult your dealer. Do not try toforce the disc out of the player.
Disc Player Error Messages (Insight model)
180
CD FORMAT
BAD DISCCHECK MANUAL
PUSH EJECT
BAD DISCCHECK MANUAL
12/07/13 16:59:25 31TM8630_185
Features
TOC
2013 Insight
Playing the FM/AM Radio (LX model and EX model without navigation system)
181
SEEK BUTTON
A.SEL BUTTON
SCAN BUTTON
SEEK BUTTON
PRESET BUTTONS
VOL/SELECT KNOB
FM/AM BUTTON
BUTTON
BUTTON
BUTTON
12/07/13 16:59:30 31TM8630_186
Features
TOC
2013 Insight
- -
-
The ignition switch must be in theACCESSORY (I) or ON (II) position.Turn the system on by pushing theFM/AM button. Adjust the volumeby turning the VOL/SELECT knob.
The band and frequency that theradio was last tuned to are displayed.To change bands, press the FM/AMbutton. On the FM band, ST will bedisplayed if the station isbroadcasting in stereo. Stereoreproduction in AM is not available.
You can use any of five methods tofind radio stations on the selectedband: tune, seek, scan, the presetbuttons, and auto select.
Use the SEEK button totune to a desired frequency. Pressthe button to tune to a higherfrequency, and the button totune to a lower frequency.
You can also operate the tunefunction by using the VOL/SELECTknob. Press the VOL/SELECT knoband you will see ‘‘SEL’’ in the display.Turn the knob right to tune to ahigher frequency, or left to tune to alower frequency. To turn it off, pressthe VOL/SELECT knob or
button, or button.The system will return to the normaldisplay about 10 seconds after youstop adjusting the tune mode.
The SEEK functionsearches up and down from thecurrent frequency to find a stationwith a strong signal. To activate it,press and hold the or sideof the SEEK button until you hear abeep, then release it.
The scan function samplesall stations with strong signals on theselected band. To activate it, pressthe SCAN button, then release it.You will see SCAN in the display.When the system finds a strongsignal, it will stop and play thatstation for about 10 seconds.
If you do nothing, the system willthen scan for the next strong stationand play it for 10 seconds. When itplays a station you want to listen to,press the SCAN button again.
To Play the FM/AM Radio
To Select a Station
TUNE SEEK
SCAN
Playing the FM/AM Radio (LX model and EX model without navigation system)
182
12/07/13 16:59:41 31TM8630_187
Features
TOC
2013 Insight
--
-
If you aretraveling and can no longer receiveyour preset stations, you can use theauto select feature to find stations inthe local area.
Press the A. SEL button. ‘‘A. SEL’’flashes in the display, and the systemgoes into scan mode for severalseconds. It stores the frequencies ofsix AM and twelve FM stations inthe preset buttons.
You will see a ‘‘0’’ displayed afterpressing a preset button if autoselect cannot find a strong station forthat preset button.
If you do not like the stations autoselect has stored, you can storeother frequencies on the presetbuttons as previously described.
press theA. SEL button. This restores thepresets you originally set.
Each preset button canstore one frequency on AM and twofrequencies on FM.
Select the desired band, AM or FM.
Use the tune, seek, or scanfunction to tune the radio to adesired station.
Repeat steps 1 through 3 to store atotal of six stations on AM andtwelve stations on FM.
Pick a preset button (1 6), thenpress and hold it until you hear a beep.
For information on FM/AM radiofrequencies and reception, see page .
1.
2.
3.
4.212
To turn off auto select,
AUTO SELECTPreset
Playing the FM/AM Radio (LX model and EX model without navigation system)
183
12/07/13 16:59:49 31TM8630_188
Features
TOC
2013 Insight
On the FM band, you can select afavorite station and display theprogram service name provided bythe radio data system (RDS).
The program service name displayfunction shows the name of thestation you are listening to. You canturn this function on or off.
To switch the function between onand off, press and release the TITLEbutton. With the system on, you willsee the ‘‘RDS INFO ON’’ message onthe display. If the station you arelistening to is an RDS station, thedisplay shows the station name.
If the station you are listening to isnot an RDS station, the displaycontinues to show the frequencywith the PS name display function on.
When you turn off this function bypressing the TITLE button, thedisplay shows ‘‘RDS INFO OFF.’’
Radio Data System (RDS)
Program Service (PS) Name Display
Playing the FM/AM Radio (LX model and EX model without navigation system)
184
PROGRAM SERVICENAME DISPLAY ON
12/07/13 16:59:55 31TM8630_189
Features
TOC
2013 Insight
With the FM band selected, you canselect the program categoryprovided by the RDS. Press
or button to displayand select an RDS category. Theprincipal RDS categories are shownas follows;
ALL PTY: All RDS category stationsROCK: Rock, classic rock and softrock musicCOUNTRY: Country musicSOFT: Adult hits and soft musicTOP 40: Top 40 hitsOLDIES: Nostalgia music and oldiesR & B: Rhythm and blues, and softrhythm and bluesRELIGION: Programs concernedwith religion.CLASSIC: Classical musicJAZZ: JazzINFO: News, information, sports,talk shows, foreign language,personality, public, college, andweatherTRAFFIC: Traffic information
Press or button toselect an RDS category. The displayshows the selected RDS categoryname for about 10 seconds. You canuse the search or scan function tofind radio stations in the selectedRDS category. If you do nothingwhile the RDS category name isdisplayed, the selected category
CONTINUED
Radio Data System (RDS) Category
Playing the FM/AM Radio (LX model and EX model without navigation system)
185
RDS CATEGORY
12/07/13 17:00:08 31TM8630_190
Features
TOC
is canceled.
2013 Insight
The scan function samples allstations with strong signals on theselected RDS category. To activate it,press and release the SCAN button.You will see SCAN in the display.The system will scan for a stationwith a strong signal in the selectedRDS category. You will also see theselected RDS category nameblinking while searching it. When itfinds a strong signal, it will stop andplay that station for about 10 seconds.
If you do nothing, the system willscan for the next strong station andplay it for 10 seconds. When it playsa station that you want to listen to,press the SCAN button again.
This function searches a frequencyfor a strong signal from thefrequency that carry the selectedRDS category information. This canhelp you to find a station in yourfavorite category. To activate it,press the or side of theSEEK button. You will see theselected RDS category nameblinking while searching it. Whenthe system finds a station, theselected RDS category name will bedisplayed again for about 5 seconds.
If the system does not find a station,‘‘NOTHING’’ blinks for about fiveseconds, then the system goes backto the last selected station.
If the system does not find a station,‘‘NOTHING’’ blinks for about fiveseconds, then the system goes backto the last selected station.
You can use the RDS programsearch or scan function even if theRDS information displayfunction is off. In this case, thedisplay shows a frequency in placeof a RDS station name.
RDS Program SCANRDS Program Search
Playing the FM/AM Radio (LX model and EX model without navigation system)
186
12/07/13 17:00:17 31TM8630_191
Features
TOC
2013 Insight
-
-
-
-
-Press the sound ( ) button toselect an appropriate setting: bass,treble, fader, balance, and SVC(speed-sensitive volumecompensation). Turn the VOL/SELECT knob to adjust the setting.
Adjusts the bass.
Adjusts the treble.
Adjusts the front-to-backstrength of the sound.
Adjusts the side-to-side strength of the sound.
Each mode is shown in the display asit changes. Turn the VOL/SELECTknob to adjust the setting to yourliking. When the level reaches thecenter, you will see ‘‘C’’ in the display.
Adjusts the volume levelbased on the vehicle speed.
Wait 10 seconds and the displayreturns to normal.
You can use the instrument panelbrightness control knob to adjust theillumination of the audio system (seepage ). The audio systemilluminates when the parking lightsare on, even if the system is
The SVC mode controls the volumebased on vehicle speed. The fasteryou go, the louder the audio volumebecomes. As you slow down, theaudio volume decreases.
The SVC has four modes: SVC OFF,SVC LOW, SVC MID, and SVCHIGH. Turn the VOL/SELECT knobto adjust the setting to your liking. Ifyou feel the sound is too loud,choose low. If you feel the sound istoo quiet, choose high.
124
Adjusting the Sound
BAS
TREBLE
FADER
BALANCE
SVC Audio System Lighting
Playing the FM/AM Radio (LX model and EX model without navigation system)
Speed-sensitive VolumeCompensation (SVC)
187
12/07/13 17:00:26 31TM8630_192
Features
TOCturned off.
2013 Insight
Playing a Disc (LX model and EX model without navigation system)
188
TITLE BUTTON
CD BUTTON DISC SLOT
EJECT BUTTON
SEEK BUTTON
SCAN BUTTON
SEEK BUTTON
RDM BUTTON
RPT BUTTON
BUTTON BUTTON
BUTTON
12/07/13 17:00:32 31TM8630_193
Features
TOC
2013 Insight
You operate the in-dash disc playerwith the same controls used for theradio. To select the disc player, pressthe CD button. You will see ‘‘CD’’ inthe display. The folder or tracknumbers are shown in the display.You can also select the displayedinformation with the TITLE button(see page ). The system willcontinuously play a disc until youchange modes.
This audio system can also playCD-Rs and CD-RWs compressed inMP3 or WMA formats. The numbersof the folder and track playing areshown in the display on the discplayer. A disc can support more than99 folders, and each folder can holdmore than 255 playable files. A disccan hold up to 999 files in total.
When there are more than 99 foldersin a disc, the audio display onlyshows two digits.
If a file on a WMA disc is protectedby digital rights management(DRM), the audio unit displaysUNSUPPORTED, and then skips tothe next file.
If you have a disc that is acombination of CD-DA tracks andMP3/WMA files, you can choosethe format to listen by pressing theCD button.
Video CDs and DVDs will not workin this unit.
A disc compressed in AAC format cannot be played in this audio system.
Depending on the software the fileswere made with, it may not bepossible to play some files, or displaysome text data.
190
CONTINUED
To Play a Disc
Playing a Disc (LX model and EX model without navigation system)
189
NOTE:Do not use discs with adhesive labels.The label can curl up and cause thedisc to jam in the unit.
12/07/13 17:00:41 31TM8630_194
Features
TOC
2013 Insight
>
The display shows up to 16characters of selected text data (thefolder name, file name, etc.).
If the text data has more than 16characters, you will see the first 15characters and the indicator onthe display. Press and hold theTITLE button until the next 16characters are shown. You can seeup to 31 characters of text data.
When you press and release theTITLE button while a disc withouttext data is playing, you will see ‘‘NOINFO’’ on the display.
With the folder name, you will seethe FOLDER indicator in the display.The TRACK indicator is shown withthe file or track name.
You can see the album, artist, andtrack name in the display. If a disc isrecorded in MP3 or WMA, you cansee the folder and file name, and thealbum, artist, and track tag.
Each time you press the TITLEbutton, the display shows you thetext, if the disc was recorded withtext data.
Insert a disc about halfway into thedisc slot. The drive will pull the discin the rest of the way to play it. Youoperate the disc player with thesame controls used for the radio.The number of the current track isshown in the display. When playing adisc in MP3 or WMA, the numbersof the current folder and file areshown. The system will continuouslyplay a disc until you change modes.
You cannot load and play 3-inch(8-cm) discs in this system.
For information on how to handleand protect compact discs, seepage .214
Text Data Display FunctionTo Load a Disc
Playing a Disc (LX model and EX model without navigation system)
190
12/07/13 17:00:49 31TM8630_195
Features
TOC
2013 Insight
-If you press and hold the TITLEbutton again, the display shows thefirst 15 characters again.
If any letter is not available, it isreplaced with ‘‘ . ’’ (dot) in the display.When the disc has no text data, youwill see ‘‘NO INFO’’ on the display.
You will also see some text dataunder these conditions:
When a new folder, file, or track isselected.
When you change the audio modeto play a disc with text data or inMP3 or WMA.
When you insert a disc, and thesystem begins to play.
When playing a CD-DA with textdata, the album and track name areshown in the display. With a disc inMP3 or WMA, the display shows thefolder and file name.
Each time youpress and release the side, theplayer skips forward to thebeginning of the next track (files inMP3/WMA mode). Press andrelease the side to skipbackward to the beginning of thecurrent track. Press it again to skipto the beginning of the previoustrack.
To move rapidly within a track, pressand hold the , or the
button.
You can also operate the trackselection by using the VOL/SELECTknob. Press the VOL/SELECT knoband you will see ‘‘SEL’’ in the display.Turn the knob to switch the tracknumber. Press the VOL/SELECTknob or button to set yourselection. To turn it off, press the
button.
You can use the SEEK button whilea disc is playing to change tracks(files in MP3/WMA mode).
In MP3/WMA mode, use theor button to select
folders in the disc, and use the SEEKbutton to change files.
CONTINUED
SEEK/SKIP
Playing a Disc (LX model and EX model without navigation system)
To Change or Select Tracks/Files
191
12/07/13 17:01:03 31TM8630_196
Features
TOC
2013 Insight
-
--
--Toselect a different folder, press the
or button. Press thebutton to skip to the next
folder, and the button to skipto the previous folder.
To continuously replaya track (file in MP3/WMA mode),press and release the RPT button.You will see RPT in the display.Press and hold the RPT button toturn it off.
Each time you press and release theRPT button, the mode changes fromfile repeat to folder repeat, then tonormal play.
This feature plays thetracks within a disc in random order.In MP3/WMA mode, all files in allfolders are played in random order.To activate random mode, press theRDM button repeatedly until you seeRDM in the display. Press and holdthe RDM button to turn it off.
Thisfeature, when activated, plays thefiles in the current folderin random order, rather than in theorder they are compressed in MP3/WMA. To activate folderrandom play, press the RDM button. You will see F-RDM in thedisplay. The system will then select and play files randomly.This continues until you deactivatefolder random play by pressing and holding the RDM button.
Each time you press and releasethe RDM button, the modechanges from folder random play,to within a disc random play,then to normal play.
This feature,when activated, replays all the filesin the selected folder in the orderthey are compressed in MP3/WMA.To activate folder repeat mode, pressthe RPT button repeatedly until yousee F-RPT in the display. The systemcontinuously replays the currentfolder. Press and hold the RPTbutton to turn it off.
You can also operate the folder andfile selection by using the VOL/SELECT knob. Press the VOL/SELECT knob and you will see‘‘SEL’’ in the display. Turn the knobto switch the folder number andpress the knob to set your selection.To turn it off, press the
button repeatedly.
In MP3/WMA mode In MP3/WMA mode In MP3/WMA modeFOLDER SELECTION
REPEAT (TRACK/FILEREPEAT)
RANDOM (Random within adisc)
FOLDER-RANDOMFOLDER-REPEAT
Playing a Disc (LX model and EX model without navigation system)
192
12/07/13 17:01:12 31TM8630_197
Features
TOC
2013 Insight
--
This feature,when activated, samples the first filein each folder on the disc in theorder they are recorded. To activatethe folder scan feature, press theSCAN button repeatedly. You willsee ‘‘F-SCAN’’ in the display. Thesystem will then play the first file inthe main folders for about 10seconds. When it plays a file that youwant to continue listening to, pressand hold the SCAN button. Whenthe system samples the first file ofall folders, F-SCAN is canceled, andthe system plays normally.
Each time you press and release theSCAN button, the mode changesfrom file scan to folder scan, then tonormal play.
Press the eject button ( ) toremove the disc. If you eject the disc,but do not remove it from the slot,the system will automatically reloadthe disc after 10 seconds and begin playing.
Press the FM/AM button to switchto the radio while a disc is playing.To play the disc, press the CD button.
If you turn the system off while adisc is playing, either with the( ) button or by turning off theignition switch, the disc will stay inthe drive. When you turn the systemback on, the disc will begin playingwhere it left off.
For information on how to handleand protect compact discs, seepage .
The SCAN functionsamples all the tracks on the disc inthe order they are recorded on thedisc (all files in the current folder inMP3 or WMA mode). To activate thescan feature, press and release theSCAN button. You will see ‘‘SCAN’’in the display. You will get a 10second sampling of each track/file inthe disc/folder. Press and hold theSCAN button to get out of scanmode and play the last track sampled.
214
In MP3/WMA modeFOLDER-SCAN
To Stop Playing a Disc
Protecting Discs
SCAN
Playing a Disc (LX model and EX model without navigation system)
193
12/07/13 17:01:20 31TM8630_198
Features
TOC
2013 Insight
The chart on the right explains theerror messages you may see in thedisplay while playing a disc.
If you see an error message in thedisplay while playing a disc, pressthe eject button. After ejecting thedisc, check it for damage ordeformation. If there is no damage,insert the disc again.
The audio system will try to play thedisc. If there is still a problem, theerror message will reappear. Pressthe eject button, and pull out the disc.
For the additional information ondamaged discs, see page .
Insert a different disc. If the newdisc plays, there is a problem withthe first disc. If the error messagecycle repeats and you cannot clear it,take your vehicle to a dealer.
CauseError Message Solution
215
Track/File format notsupported
Mechanical Error
FOCUS Error
TOC Error
Current track will be skipped. The nextsupported track or file plays automatically.Press the EJECT button and pull out the disc.Check the disc for serious damage, signs ofdeformation, excessive scratches, and/or dirt(see page 215). Insert the disc again. If the codedoes not disappear, or the disc cannot beremoved, consult your dealer. Do not try toforce the disc out of the player.Press the EJECT button and pull out the disc.Make sure it is inserted correctly in the discplayer.Make sure the disc is not scratched or damaged.For more information, see page 215.
Disc Player Error Messages (LX model and EX model without navigation system)
194
UNSUPPORTED
BAD DISCPLEASE CHECK
OWNERSMANUAL
PUSH EJECT
CHECK DISC
12/07/13 17:01:26 31TM8630_199
Features
TOC
2013 Insight
+-
Playing an iPod (U.S. LX model and EX model without navigation system)
195
BUTTON
BUTTON
TITLE BUTTON
BUTTON
AUX BUTTONiPod INDICATOR
USB INDICATOR
RDM BUTTON
RPT BUTTON
SEEK (SKIP ) BUTTONSEEK (SKIP ) BUTTON
12/07/13 17:01:32 31TM8630_200
Features
TOC
2013 Insight
Do not connect your iPod using ahub.
Do not keep the iPod in thevehicle. Direct sunlight and highheat will damage it.
Do not use an extension cablebetween the USB adapter cableequipped with your vehicle andyour dock connector.
We recommend backing up yourdata before playing it.
Some devices cannot be poweredor charged via the USB adapter. Ifthis is the case, use the accessoryadapter to supply power to yourdevice.
iPod models confirmed to becompatible with your audio systemusing the USB adapter cable are:
This audio system can play the audiofiles on the iPod with the samecontrols used for the in-dash discplayer. To play an iPod, connect it tothe USB adapter cable in the consolecompartment by using your dockconnector, then press the AUXbutton. The ignition switch must bein the ACCESSORY (I) or ON (II)position. The iPod will also berecharged with the ignition switch inthese positions.
The system will only play songsstored on the iPod with iTunes.
iPod and iTunes are registeredtrademarks owned by Apple Inc.
This system may not work with allsoftware versions of these devices.
ModeliPod classic 80/160 GiPod classic 120 GiPod classic 160 G (launch in 2009)iPod (5th generation)iPod nanoiPod touch
Playing an iPod (U.S. LX model and EX model without navigation system)
To Play an iPod
196
NOTE:
12/07/13 17:01:41 31TM8630_201
Features
TOC
2013 Insight
Unclip the USB connector bypivoting it, and pull out the USBadapter cable in the consolecompartment.
Connect your dock connector tothe iPod correctly and securely.
Install the dock connector to theUSB adapter cable securely.
If the iPod indicator does not appearin the audio display, check theconnections, and try to reconnect theiPod a few times.
If the audio system still does notrecognize the iPod, the iPod mayneed to be reset. Follow theinstructions that came with youriPod, or you can find resetinstructions online at
1.2.
3.
www.apple.com/
CONTINUED
Connecting an iPod
Playing an iPod (U.S. LX model and EX model without navigation system)
197
DOCK CONNECTOR
USB ADAPTERCABLE
USB CONNECTOR
USB ADAPTER CABLE
12/07/13 17:01:49 31TM8630_202
Features
TOC
2013 Insight
-+
-
>
Use the SKIP button while an iPod isplaying to change files.
Each time you press the(SKIP ) button, the system
skips forward to the beginning of thenext file. Press the (SKIP )button, to skip backward to thebeginning of the current file. Press itagain to skip to the beginning of theprevious file.
To move rapidly within a file, pressand hold either side ( or )of the SKIP button.
Each time you press the TITLEbutton the display mode switchesbetween the album name, the songname, the artist name, or name off(which turns off the text display).
The display shows up to 16characters of the selected data. If thetext data has more than 16characters, you will see the first 15characters and the indicator inthe display. Press and hold theTITLE button until the next 16characters are shown.
To Change or Select FilesText Data Display Function
SKIP
Playing an iPod (U.S. LX model and EX model without navigation system)
198
12/07/13 17:01:57 31TM8630_203
Features
TOC
2013 Insight
-
-You can also select a file from anylist on the iPod menu: playlists,artists, albums and songs, by usingthe VOL/SELECT knob. Push theVOL/SELECT knob to switch thedisplay to an iPod menu, then turnthe VOL/SELECT knob to select adesired list. Press the VOL/SELECTknob to set your selection.
The display shows items on theselected list. Turn the VOL/SELECT knob to select an item, thenpress the VOL/SELECT knob to setyour selection.
If you select ‘‘ALL,’’ all available fileson the selected list are played.
Pressing the button goes backto the previous display and pressingthe TITLE button cancels thissetting mode.
You can select any type of repeat andshuffle mode by using the RPTbutton or the RDM button.
This featurecontinuously plays a file. To activatethe repeat feature, press the RPTbutton. You will see ‘‘RPT’’ in thedisplay. To turn it off, press the RPTbutton again.
This featureplays all available files in a selectedlist (playlists, artists, albums orsongs) in random order. To activatethe shuffle all feature, press theRDM button. You will see ‘‘RDM’’ inthe display. To turn it off, press andhold the RDM button.
CONTINUED
To Select Repeat or Shuffle Mode:
REPEAT
SHUFFLE ALL
Playing an iPod (U.S. LX model and EX model without navigation system)
199
Press theVOL/SELECT knob.
12/07/13 17:02:06 31TM8630_204
Features
TOC
2013 Insight
-
*
*
This featureplays all available albums in aselected list (playlists, artists, albumsor songs) in random order. The filesin each album are played in therecorded order. To activate theshuffle album feature, press theRDM button repeatedly. You will see‘‘F-RDM’’ in the display. To turn itoff, press and hold the RDM button.
Each time you press the RDMbutton, the mode changes fromshuffle all play to shuffle album play,then to normal play.
To play the radio when an iPod isplaying, press the FM/AM button. Ifa disc is in the audio unit, press theCD button to play the disc.
You can disconnect the iPod at anytime when you see the ‘‘OK todisconnect’’ message in the iPoddisplay. Always make sure you seethe ‘‘OK to disconnect’’ message inthe iPod display before youdisconnect it. Make sure to followthe iPod’s instructions on how todisconnect the dock connector fromthe USB adapter cable.
The displayed message may varyon models or versions. On somemodels, there is no messageto disconnect.
If you reconnect the same iPod, thesystem may begin playing where itleft off, depending on what mode theiPod is in when it is reconnected.
When you disconnect the iPod whileit is playing, the display shows ‘‘USBNO DATA.’’
:
SHUFFLE ALBUM To Stop Playing Your iPod
Disconnecting an iPod
Playing an iPod (U.S. LX model and EX model without navigation system)
200
12/07/13 17:02:14 31TM8630_205
Features
TOC
2013 Insight
If you see an error message on theaudio display while playing an iPod, find the solution in thechart to the right. If you cannotclear the error message, take yourvehicle to your dealer.
CauseError Message Solution
USB ROM Error
Appears when anincompatible device isconnected
No files in iPod
Use of unsupportediPod
Recognition failure ofiPod
There is a problem with the USB adapter unit.Disconnect the device. Then, turn the audiosystem off, and turn it on again. Do notreconnect the device that caused the error.
Appears when the iPod is empty. Store somefiles in the iPod.Appears when an unsupported iPod isconnected. See page 196 for the specificationinformation for iPods. If it appears when asupported iPod is connected, update the iPodsoftware to the newer version.Appears when the system does notacknowledge the iPod. Reconnect the iPod.
iPod Error Messages (U.S. LX model and EX model without navigation system)
201
USB ERRORBAD USBDEVICE
PLEASE CHECKOWNERSMANUAL
iPod NO SONG
UNSUPPORTEDVER.
CONNECT RETRY
12/07/13 17:02:18 31TM8630_206
Features
TOC
2013 Insight
+-
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system)
202
TITLE BUTTON
SEEK (SKIP )BUTTON
USB INDICATOR AUX BUTTON
SEEK (SKIP )BUTTON
RDM BUTTON
RPT BUTTON
VOL/SELECT BUTTON
BUTTON
BUTTON
BUTTON
12/07/13 17:02:24 31TM8630_207
Features
TOC
2013 Insight
*
*
CONTINUED
The recommended USB flashmemory devices are 256 MB orhigher, and formatted with the FATfile system. Some digital audioplayers may be compatible as well.Some USB flash memory devices(such as devices with security lock-out features, etc.) will not work inthis audio unit.
The audio system reads and playsthe audio files on the USB flashmemory device in MP3, WMA orAAC formats. Depending on theformat, the display shows MP3,WMA or AAC when a USB flashmemory device is playing.
This audio system can operate theaudio files on a USB flash memorydevice with the same controls usedfor the in-dash disc player. To play aUSB flash memory device, connect itto the USB adapter cable in theconsole compartment, then press theAUX button.
Only AAC format files recorded with iTunes are playable on this audio unit.
:
To Play a USB Flash MemoryDevice
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system)
203
12/07/13 17:02:30 31TM8630_208
Features
TOC
2013 Insight
Do not use a device such as a cardreader or hard drive as the deviceor your files may be damaged.
Do not connect your USB flashmemory device using a hub.
Do not use an extension cable tothe USB adapter cable equippedwith your vehicle.
Do not keep a USB flash memorydevice in the vehicle. Directsunlight and high heat will damageit.
Depending on the type andnumber of files, it may take sometime before they begin to play.
Depending on the software thefiles were made with, it may not bepossible to play some files, ordisplay some text data.
Depending on the type ofencoding and writing softwareused, there may be cases wherecharacter information does notdisplay properly.
We recommend backing up yourdata before playing a USB flashmemory device.
Some devices cannot be poweredor charged via the USB adapter. Ifthis is the case, use the accessoryadapter to supply power to yourdevice.
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system)
204
NOTE:
12/07/13 17:02:37 31TM8630_209
Features
TOC
2013 Insight
CONTINUED
Unclip the USB connector bypivoting it, and pull out the USBadapter cable in the consolecompartment.
When the USB flash memory deviceis connected, the USB indicator isshown in the display.
Connect the USB flash memorydevice to the USB connectorcorrectly and securely.1.
2.
Connecting a USB Flash Memory Device
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system)
205
USB CONNECTOR
USB ADAPTER CABLE
USB ADAPTER CABLE
12/07/13 17:02:44 31TM8630_210
Features
TOC
2013 Insight
-+
-
-
>
Use the SKIP button while a USBflash memory device is playing tochange files.
Each time you press the(SKIP ) button, the system
skips forward to the beginning of thenext file. Press the (SKIP )button, to skip backward to thebeginning of the current file. Press itagain to skip to the beginning of theprevious file.
To move rapidly within a file, pressand hold either side ( or )of the SKIP button.
Each time you press the TITLEbutton, the display mode shows youin sequence, the folder name, the filename, the artist name, the albumname, the song name, or name off(which turns off the text display).
The display shows up to 16characters of the selected data. If thetext data has more than 16characters, you will see the first 15characters and the indicator inthe display. Press and hold theTITLE button until the next 16characters are shown.
Toselect a different folder, press the
button or button.Press the button to skip tothe next folder, and press the
button to skip to thebeginning of the previous folder.
To Change or Select FilesText Data Display Function
SKIP
FOLDER SELECTION
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system)
206
12/07/13 17:02:53 31TM8630_211
Features
TOC
2013 Insight
CONTINUED
You can also select a folder or file byusing the VOL/SELECT knob. Pushthe VOL/SELECT knob to switchthe display to the folder or file list,then turn the VOL/SELECT knob toselect a folder or file. Press theVOL/SELECT knob to set yourselection.
You can select any type of repeat,random and scan modes by using theRPT button, RDM button, or SCANbutton.
Pressing the button goes backto the previous display and pressingthe TITLE button cancels thissetting mode.
To Select a File from Folderand File Lists
To Select Repeat,Random or Scan Mode:
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system)
207
Folder Selection
Track Selection
Press theVOL/SELECT knob.
12/07/13 17:03:01 31TM8630_212
Features
TOC
2013 Insight
- - -This featurecontinuously plays a file. To activatethe repeat feature, press the RPTbutton. You will see ‘‘RPT’’ in thedisplay. To turn it off, press and holdthe RPT button.
This featurereplays all the files in the selectedfolder in the order they are stored.To activate the folder repeat feature,press the RPT button repeatedly.You will see ‘‘F-RPT’’ in the display.To turn it off, press and hold theRPT button.
Each time you press and release theRPT button, the mode changes fromfile repeat to folder repeat, then tonormal play.
This feature plays allthe files in random order. To activatethe track random feature, press theRDM button. You will see ‘‘RDM’’ inthe display. To turn it off, press andhold the RDM button.
REPEAT FOLDER REPEAT RANDOM
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system)
208
12/07/13 17:03:05 31TM8630_213
Features
TOC
2013 Insight
---
Each time you press and release theSCAN button, the mode changesfrom file scan to folder scan, then tonormal play.
This featuresamples the first file in each folder inthe order they are stored. Toactivate the folder scan feature,press the SCAN button repeatedly.You will see ‘‘F-SCAN’’ in the display.You will get a 10 second sampling ofthe first file in each folder. Press andhold the SCAN button to get out ofthe folder scan mode and play thelast file sampled.
This feature samples allfiles in the current folder in theorder they are stored. To activatethe scan feature, press the SCANbutton. You will see ‘‘SCAN’’ in thedisplay. You will get a 10 secondsampling of each file in the folder.Press and hold the SCAN button toget out of the scan mode and playthe last file sampled.
Thisfeature plays the files in the currentfolder in random order. To activatethe folder random feature, press theRDM button repeatedly. You will see‘‘F-RDM’’ in the display. To turn itoff, press and hold the RDM button.
Each time you press the RDMbutton, the mode changes from trackrandom, play to folder random play,then to normal play.
FOLDER SCANSCANFOLDER RANDOM
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system)
209
12/07/13 17:03:10 31TM8630_214
Features
TOC
2013 Insight
To play the radio when a USB flashmemory device is playing, press theFM/AM button. If a disc is in theaudio unit, press the CD button toplay the disc.
You can disconnect the USB flashmemory device at any time even ifthe USB mode is selected on theaudio system. Always follow the USBflash memory device’s instructionswhen you remove it.
When you disconnect the USB flashmemory device while it is playing,the display shows ‘‘USB NO DATA.’’
If you reconnect the same USB flashmemory device, the system willbegin playing where it left off.
To Stop Playing a USB FlashMemory Device
Disconnecting a USB Flash Memory Device
Playing a USB Flash Memory Device (U.S. LX model and EX model without navigation system)
210
12/07/13 17:03:16 31TM8630_215
Features
TOC
2013 Insight
If you see an error message on theaudio display while playing a USBflash memory device, find thesolution in the chart to the right. Ifyou cannot clear the error message,take your vehicle to your dealer.
CauseError Message Solution
USB ROM Error
Appears when anincompatible device isconnected
Use of unsupportedfiles
No files in USB flashmemory device
Use of unsupportedUSB flash memorydevice
There is a problem with the USB adapter unit.Disconnect the device. Then, turn the audiosystem off, and turn it on again. Do notreconnect the device that caused the error.
Appears when the files in the USB flashmemory device are DRM or an unsupportedformat. This error message appears for about 3seconds, then plays the next song.Appears when the USB flash memory device isempty or there are no MP3, WMA, or AAC filesin the USB flash memory device. Save someMP3, WMA, or AAC files in the USB flashmemory device.Appears when an unsupported device isconnected. See page 203 for the specificationinformation for the USB flash memory device.If it appears when the supported device isconnected, reconnect the device.
USB Flash Memory Device Error Messages (U.S. LX model and EX model without navigation system)
211
USB ERRORBAD USBDEVICE
PLEASE CHECKOWNERSMANUAL
UNPLAYABLEFILE
USB NO SONG
UNSUPPORTED
12/07/13 17:03:20 31TM8630_216
Features
TOC
2013 Insight
The radio can receive the completeAM and FM bands.
Those bands cover thesefrequencies:
AM band: 530 to 1,710 kHzFM band: 87.7 to 107.9 MHz
How well the radio receives stationsis dependent on many factors, suchas the distance from the station’stransmitter, nearby large objects,and atmospheric conditions.
Driving very near the transmitter ofa station that is broadcasting on afrequency close to the frequency ofthe station you are listening to canalso affect your radio’s reception.You may temporarily hear bothstations, or hear only the station youare close to.
A radio station’s signal gets weakeras you get farther away from itstransmitter. If you are listening to anAM station, you will notice the soundvolume becoming weaker, and thestation drifting in and out. If you arelistening to an FM station, you willsee the stereo indicator flickering offand on as the signal weakens.Eventually, the stereo indicator willgo off and the sound will fadecompletely as you get out of range ofthe station’s signal.
Radio stations on the AM band areassigned frequencies at least 10 kHzapart (530, 540, 550). Stations on theFM band are assigned frequencies atleast 0.2 MHz apart (87.9, 88.1, 88.3).
Stations must use these exactfrequencies. It is fairly common forstations to round-off the frequency intheir advertising, so your radio coulddisplay a frequency of 100.9 eventhough the announcer may identifythe station as ‘‘FM101.’’
Radio Frequencies Radio Reception
FM/AM Radio Reception
212
12/07/13 17:03:29 31TM8630_217
Features
TOC
2013 Insight
Radio signals, especially on the FMband, are deflected by large objectssuch as buildings and hills. Yourradio then receives both the directsignal from the station’s transmitter,and the deflected signal. This causesthe sound to distort or flutter. This isa main cause of poor radio receptionin city driving.
Radio reception can be affected byatmospheric conditions such asthunderstorms, high humidity, andeven sunspots. You may be able toreceive a distant radio station oneday and not receive it the next daybecause of a change in conditions.
Electrical interference from passingvehicles and stationary sources cancause temporary reception problems.
As required by the FCC:Changes or modifications not expresslyapproved by the party responsible forcompliance could void the user’sauthority to operate the equipment.
FM/AM Radio Reception
213
12/07/13 17:03:34 31TM8630_218
Features
TOC
2013 Insight
When a disc is not being played,store it in its case to protect it fromdust and other contamination. Toprevent warpage, keep discs out ofdirect sunlight and extreme heat.
To clean a disc, use a clean soft cloth.Wipe across the disc from the centerto the outside edge.
A new disc may be rough on theinner and outer edges. The smallplastic pieces causing this roughnesscan flake off and fall on therecording surface of the disc,causing skipping or other problems.Remove these pieces by rubbing theinner and outer edges with the sideof a pencil or pen.
Handle a disc by its edges; nevertouch either surface. Do not placestabilizer rings or labels on thedisc. These, along with contamination from finger prints,liquids, and felt- tip pens, can causethe disc to not play properly, orpossibly jam in the drive.
When recording a CD-R orCD-RW, the recording must beclosed for it to be used by thesystem.
When using CD-R or CD-RW discs,use only high quality discs labeledfor audio use.
Never try to insert foreign objects inthe disc player.
Handle your discs properly toprevent damage and skipping.
Play only standard round discs.Odd-shaped discs may jam in thedrive or cause other problems.
General Information Protecting Discs
Protecting Your Discs
214
Do not use discs with adhesive labels.The label can curl up and cause thedisc to jam in the unit.
12/07/13 17:03:43 31TM8630_219
Features
TOC
2013 Insight
The in-dash disc player/changer hasa sophisticated and delicatemechanism. If you insert a damageddisc as indicated in this section, itmay become stuck inside anddamage the audio unit.
Examples of these discs are shownto the right:
Bubbled, wrinkled, labeled, and excessively thick discs
Damaged discs Poor quality discs
1.
2. 3.
CONTINUED
Additional Information onRecommended Discs
Protecting Your Discs
215
Sealed
Warped BurrsChipped/Cracked
With Label/Sticker
With PlasticRing
Using PrinterLabel Kit
Bubbled/Wrinkled
12/07/13 17:03:54 31TM8630_220
Features
TOC
2013 Insight
Small, irregular shaped discs Discs with scratches, dirty discs
CD-R or CD-RW may not play dueto the recording conditions.
Scratches and fingerprints on thediscs may cause the sound to skip.
Recommended discs are printedwith the following logo.
Audio unit may not play thefollowing formats.
4. 5.
Protecting Your Discs
216
Fingerprints, scratches, etc.
3-inch (8-cm) CD Triangle Shape
Arrow ShapeCan Shape
12/07/13 17:04:03 31TM8630_221
Features
TOC
2013 Insight
▲ ▼
+
-
+ -
+-
The VOL button adjusts the volumeup ( ) or down ( ). Press the topor bottom of the button and hold ituntil the desired volume is reached,then release it.
The MODE button changes themode. Pressing the buttonrepeatedly selects FM1, FM2, AM,disc or a PC card (if a disc or a PCcard is loaded), or an audio unitconnected to the auxiliary input jackor the USB adapter cable.
If you are listening to the radio, usethe CH button to change stations.Each time you press the top ( ) ofthe button, the system goes to thenext preset station on the band youare listening to. Press the bottom( ) to go back to the previousstation. If you press and hold the CHbutton ( ) or ( ), the system goesinto the seek mode. It finds a stationwith a strong signal.
If you are playing a disc, iPod or USBflash memory device, the systemskips to the beginning of the nexttrack (file in MP3, WMA or AACformat) each time you press the top( ) of the CH button. Press thebottom ( ) to return to thebeginning of the current track/file.Press it twice to return to theprevious track/file.
You will see the track/file numberand the elapsed time. If the disc hastext data or is compressed in MP3 orWMA, you can also see any otherinformation (track title, file name,folder name, etc.).
Three controls for the audio systemare mounted in the steering wheelhub. These let you control basicfunctions without removing yourhand from the wheel.
CONTINUED
On U.S. LX model and EX models
Remote Audio Controls
217
CH BUTTON
MODE BUTTONVOL BUTTON
12/07/13 17:04:11 31TM8630_222
Features
TOC
2013 Insight
+
-
+
-
In MP3 or WMA mode, you can usethe seek function to select folders.Press and hold the top ( ) of theCH button until you hear a beep toskip forward to the first file of thenext folder. Press the bottom ( ) toskip backward to the previous folder.
If you are playing a PC card, pressthe top ( ) of the CH button toadvance to the next file. Press thebottom ( ) to go back to theprevious file.
Your vehicle has the auxiliary inputjack on the front panel. The systemwill accept auxiliary input fromstandard audio accessories using a1/8 inch (3.5 mm) stereo miniplug.
When a compatible audio unit isconnected to the jack, press the CD/AUX (on vehicles with navigationsystem) or AUX (on vehicles withoutnavigation system) button to select it.
Auxiliary Input Jack
Remote Audio Controls, Auxiliary Input Jack
218
On Insight model and EX model withnavigation system
On LX model and EX model withoutnavigation system
12/07/13 17:04:17 31TM8630_223
Features
TOC
2013 Insight
If your vehicle’s battery isdisconnected or goes dead, the audiosystem disables itself. If this happens, you will see ‘‘ENTERCODE’’ in the frequency display nexttime you turn on the system. Use thepreset bars (icons on models with navigation system) to enter the five-digit code. The code is on the Anti-theft Identification Card included in your owner’s manual kit. When itis entered correctly, the radio will start playing.
The Anti-theft Identification Cardalso lists your audio serial number. Itis best to store the card in a safeplace at home. In addition, youshould write the audio system’sserial number in this owner’s manual.
If you make a mistake entering thecode, do not start over; complete thefive-digit sequence, then enter thecorrect code. You have ten tries toenter the correct code. If you are
unsuccessful in ten attempts, youmust then leave the system on forone hour before trying again.
The system will retain your AM andFM presets even if power isdisconnected.
We recommend that you register thesecurity code at Owner Link (owners.honda.com). If you lose the Anti-theft Identification Card beforeregistering the code at Owner Link,you must obtain the code from yourdealer or
. To do this, you will need theaudio system’s serial number. If youdo not have the serial number withyou, ask your dealer or go to
forinformation on how to retrieve it.
If you lose the Anti-theftIdentification Card, you must obtainthe code from your dealer. To do this,you will need the audio system’sserial number. If you do not have theserial number with you, ask yourdealer how to retrieve it.
You need to enter a separate codefor the navigation system toreactivate. The Anti-theft Card alsolists the navigation system’s securitycode and serial number. Follow thesame procedure to retrieve the serialnumber and obtain the code, andread the navigation system manualfor details.
https://radio-navicode.honda.com/
https://radio-navicode.honda.com/
On models with navigation systemU.S. owners
Canadian owners
Radio Theft Protection
219
12/07/13 17:04:24 31TM8630_224
Features
TOC
2013 Insight
For example: 1:06 will reset to 1:001:52 will reset to 2:00
When you set the time, the ignitionswitch must be ACCESSORY (I) orON (II) position.
To set the time, press the CLOCKbutton until you hear a beep. Thedisplayed time begins to blink.
Change the hours by pressing the H(hour) button until the numbersadvance to the desired time. Changethe minutes by pressing the M(minute) button until the numbersadvance to the desired time.
Press the CLOCK button again toenter the set time.
You can quickly set the time to thenearest hour. If the displayed time isbefore the half hour, press and holdthe CLOCK button, then press the R(reset) button to set the time back tothe previous hour. If the displayedtime is after the half hour, the sameprocedure sets the time forward tothe beginning of the next hour.
Setting the Clock (Models without navigation system)
220
CLOCK BUTTON(A.SEL side of the A.SEL/SCAN bar)
HOUR BUTTON(PRESET 4)
HOUR BUTTON(PRESET 1)
RESET BUTTON(PRESET 6)
EX model without navigation systemand LX model
MINUTE BUTTON(PRESET 5)
CLOCK BUTTON(FM/AM button)
MINUTE BUTTON(PRESET 2)
RESET BUTTON(PRESET 3)
Insight model
12/07/13 17:04:33 31TM8630_225
Features
TOC
2013 Insight
The alarm also activates if apassenger inside the locked vehicleturns the ignition switch on.
Do not attempt to alter this systemor add other devices to it.
Once the security system is sets,opening any door, the hatch, or thehood without using the key or theremote transmitter, will cause thealarm to activate. It also activates ifthe audio unit is removed from thedashboard or the wiring is cut.
The security system helps to protectyour vehicle and valuables from theft.The horn sounds and a combinationof headlights, parking lights, sidemarker lights and taillights flashes ifsomeone attempts to break into yourvehicle or remove the audio unit.This alarm continues for twominutes, then the system resets. Todeactivate the system before the twominutes have elapsed, unlock thedriver’s door with the key or theremote transmitter.The security system setsautomatically 15 seconds after youlock the doors, hood, and the hatch.For the system to activate, you mustlock the doors and the hatch fromthe outside with the key, or usedriver’s lock tab, door lock masterswitch, or remote transmitter. Thesecurity system indicator on theinstrument panel starts blinkingimmediately to show you the systemis setting itself.
To see if the system is setafter you exit the vehicle, press theLOCK button on the remotetransmitter within five seconds. Ifthe system is set, the horn will beeponce.
The security system does not set ifthe hood, hatch, or any door is notfully closed. If the system will not set,check the door and hatch openindicator on the instrument paneland multi-information display (seepage ) to see if the doors andhatch are fully closed. Since it is notpart of the monitor display, manuallycheck the hood.
12
On LX and EX models
Security System
221
NOTE:SECURITY SYSTEM INDICATOR
12/07/13 17:04:40 31TM8630_226
Features
TOC
2013 Insight
Push the CRUISE button on thesteering wheel. The CRUISEMAIN indicator on the instrumentpanel comes on.
Accelerate to the desired cruisingspeed above 25 mph (40 km/h).
Press and release the SET/DECEL button on the steeringwheel. The CRUISE CONTROLindicator on the instrument panelcomes on to show the system isnow activated.
Cruise control allows you to maintaina set speed above 25 mph (40 km/h)without keeping your foot on theaccelerator pedal. It should be usedfor cruising on straight, openhighways. It is not recommended forcity driving, winding roads, slipperyroads, heavy rain, or bad weather.
Cruise control may not hold the setspeed when you are going up anddown hills. If your vehicle speedincreases going down a hill, use thebrakes to slow down. This will cancelthe cruise control. To resume the setspeed, press the RES/ACCEL button.The CRUISE CONTROL indicatoron the instrument panel will comeback on.
1.
2.
3.On LX and EX models Using the Cruise Control
Cruise Control
222
CANCELBUTTON
CRUISE BUTTON RES/ACCELBUTTON
SET/DECELBUTTON
Improper use of the cruisecontrol can lead to a crash.
Use the cruise control onlywhen traveling on openhighways in good weather.
12/07/13 17:04:48 31TM8630_227
Features
TOC
2013 Insight
You can increase the set cruisingspeed in any of these ways:
Press and hold the RES/ACCELbutton. When you reach thedesired cruising speed, release thebutton.
To increase your speed in verysmall amounts, tap the RES/ACCEL button. Each time you dothis, the vehicle will speed upabout 1 mph (1.6 km/h).
Press and hold the SET/DECELbutton. Release the button whenyou reach the desired speed.
To slow down in very smallamounts, tap the SET/DECELbutton. Each time you do this,your vehicle will slow down about1 mph (1.6 km/h).
You can decrease the set cruisingspeed in any of these ways:
Even with the cruise control turnedon, you can still use the acceleratorpedal to speed up for passing. Aftercompleting the pass, take your footoff the accelerator pedal. The vehiclewill return to the set cruising speed.
Push on the accelerator pedal.Accelerate to the desired cruisingspeed, then press the SET/DECEL button.
Resting your foot on the brake pedalcauses cruise control to cancel.
Tap the brake pedal lightly withyour foot. The CRUISECONTROL indicator on theinstrument panel will go out.When the vehicle slows to thedesired speed, press the SET/DECEL button.
Changing the Set Speed
Cruise Control
223
12/07/13 17:04:56 31TM8630_228
Features
TOC
2013 Insight
You can cancel cruise control in anyof these ways:
Push the CANCEL button on thesteering wheel.
Push the CRUISE button on thesteering wheel.
Tap the brake pedal.
Pressing the CRUISE button turnsthe system off and erases theprevious cruising speed.
When you push the CANCEL button,or tap the brake pedal, the systemwill remember the previously-setcruising speed. To return to thatspeed, accelerate to above 25 mph(40 km/h) and then press andrelease the RES/ACCEL button. TheCRUISE CONTROL indicator comeson. The vehicle will accelerate to thesame cruising speed as before.
Tapping either of the paddle shiftersshifts the speed up or down, but doesnot cancel the cruise control. Formore information on driving withpaddle shifters, see page .276
EX models onlyCanceling Cruise Control Resuming the Set Speed
Cruise Control
224
CRUISE BUTTON
CANCELBUTTON
RES/ACCELBUTTON
SET/DECELBUTTON
12/07/13 17:05:04 31TM8630_229
Features
TOC
2013 Insight
-
-
Press andrelease to give a command or answera call.
Press andrelease to end a call, go back to theprevious command, or cancel thecommand.
To use HFL, you need a Bluetooth-compatible cell phone. For a list ofcompatible phones, pairingprocedures, and special featurecapabilities:
In the U.S., visitor call (888) 528-7876.
In Canada, visitor call (888) 528-7876.
HandsFreeLink (HFL)allows you to place and receivephone calls using voice commands,without handling your cell phone.
For models with the navigationsystem, see the Navigation SystemManual for how to operate the
HandsFreeLink .
handsfreelink.honda.com
www.handsfreelink.ca,
Bluetooth
Bluetooth
CONTINUED
Using HFL
HFL Talk button
HFL Back button
HFL Buttons
Bluetooth HandsFreeLink (Models without navigation system)
225
HFL TALKBUTTON
HFL BACK BUTTON
12/07/23 16:33:55 31TM8630_230
Features
TOC
2013 Insight
####
Try to reduce all backgroundnoise. If the microphone picks upvoices other than yours,commands may be misinterpreted.
Many commands can be spokentogether. For example, you cansay ‘‘Call 123-456- ’’ or‘‘Dial Peter.’’
Press and release the HFL Talkbutton each time you want tomake a command. After the beep,speak in a clear, natural tone.
Air or wind noise from thedashboard and side vents and allwindows may interfere with themicrophone. Adjust or close themas necessary.
To change the volume level ofHFL, use the audio system volume knob or the steering wheel volume controls.
Voice Control Tips
Bluetooth HandsFreeLink (Models without navigation system)
226
MICROPHONE
12/07/13 17:05:18 31TM8630_231
Features
TOC
2013 Insight
CONTINUED
To hear general HFL information,including help on pairing a phoneor setting up the system, say‘‘Tutorial.’’
For help at any time, including alist of available commands, say‘‘Hands free help.’’
As an incoming call notification, youwill see the following display:
The Bluetooth icon will alsoappear on the display when a phoneis linked.
Some phones may send battery,signal strength, and roaming statusinformation to HFL.
Help Features Information Display
Bluetooth HandsFreeLink (Models without navigation system)
227
ROAM STATUS
HFLMODE
PHONE DIALING
SIGNAL STRENGTH BATTERYLEVEL STATUS
12/07/13 17:05:26 31TM8630_232
Features
TOC
2013 Insight
####
How to Use HFL
Bluetooth HandsFreeLink (Models without navigation system)
228
‘‘Phone Setup’’
‘‘Call’’ or ‘‘Dial’’
‘‘Pair’’
‘‘Edit’’
‘‘Delete’’
‘‘Jim Smith’’
‘‘Set PairingCode’’
The ignition switch must be in the ACCESSORY (I) or ON (II) position.
‘‘List’’
‘‘Status’’
‘‘Next Phone’’
‘‘123-555- ’’
Press HFLTalk button
Press and release the HFL Talk button each time you give a command.
Edit the name of a paired phone
Delete a paired phone from the system
Hear a list of all phones paired to the system
Hear which paired phone is currently linked to the system
Search for another previously paired phone to link to
Set the pairing code to a ‘‘Fixed’’ or ‘‘Random’’ number
Pair a phone to the system
Enter desired phone number
Once a phonebook entry is stored, you can say a name here.
(See page 231)
(See page 232)
(See page 232)
(See page 232)
(See page 233)
(See page 233)
(See page 233)
(See page 234)
(See page 234)
12/07/13 17:05:34 31TM8630_233
Features
TOC
2013 Insight
CONTINUED
Bluetooth HandsFreeLink (Models without navigation system)
229
‘‘Redial’’
‘‘Transfer’’
‘‘Mute’’
‘‘Send’’
‘‘Phonebook’’
‘‘Store’’
‘‘Edit’’
‘‘Delete’’
‘‘ReceiveContact’’
‘‘List’’
Press HFLTalk button
Press and release the HFL Talk button each time you give a command.
Send numbers or names during a call
If your phone supports this function, use this to transfer contacts fromyour phone to HFL
Mute your voice to the person at the other end of the call
Store a phonebook entry
Edit the number of an existing phonebook entry
Delete a phonebook entry
Hear a list of all stored phonebook entries
Redial the last number called (See page 235)
Transfer a call from HFL to your phone, or from your phone to HFL (See page 236)
(See page 236)
(See page 236)
(See page 237)
(See page 237)
(See page 238)
(See page 238)
(See page 238)
12/07/13 17:05:41 31TM8630_234
Features
TOC
2013 Insight
*
*
Bluetooth HandsFreeLink (Models without navigation system)
230
‘‘Change Language’’
‘‘Hands Free Help’’
‘‘SystemSet up’’
‘‘Tutorial’’
‘‘Clear’’
‘‘Auto Transfer’’
‘‘Call Notification’’
‘‘Security’’
‘‘Change Passcode’’
Press HFLTalk button
Press and release the HFL Talk button each time you give a command.
Apply a security passcode to the system that must be input at each keycycle to access the system
Change your security passcode
Set how you would like to be notified of an incoming call
Set calls to automatically transfer from your phone to HFL when youenter the vehicle
Hear a list of available commands and additional information describing each command
Clear the system of all paired phones, phonebook entries and securitypasscode
Change language from English to French
Hear a tutorial for general rules on using the system
Canadian models:
(See page 239)
(See page 240)
(See page 240)
(See page 240)
(See page 241)
(See page 242)
(See page 227)
(See page 227)
12/07/13 17:05:48 31TM8630_235
Features
TOC
2013 Insight
To use HFL, you need to pair yourBluetooth-compatible cell phone tothe system.
This command group is available forpaired cell phones.
You cannot pair your phone whilethe vehicle is moving.
Your phone must be in discoveryor search mode to pair. Refer toyour phone’s manual.
Up to six phones can be paired.
Your phone’s battery may drainfaster when it is paired to HFL.
If after three minutes your phoneis not ready to pair or a phone isnot found, the system will time outand return to idle.
Press and release the HFL Talkbutton. If you are pairing a phonefor the first time, HFL will giveyou information about the pairingprocess. If it is not the first phoneyou are pairing, say ‘‘
’’ and say ‘‘ .’’
Follow the HFL prompts and putyour phone in discovery or searchmode. HFL will give you a 4-digitpairing code and begin searchingfor your phone.
When your phone finds aBluetooth device, select HFL fromthe options and enter the 4-digitcode from the previous step.
Follow the HFL prompts andname the newly paired phone.
1.
2.
3.
4.
CONTINUED
Phone Setup
Phonesetup Pair
Phone pairing tips
To pair a cell phone:
Bluetooth HandsFreeLink (Models without navigation system)
231
12/07/13 17:05:59 31TM8630_236
Features
TOC
2013 Insight
Say ‘‘ .’’
Say ‘‘ ’’ after the prompts.
If there is more than one phonepaired to the system, HFL will askyou which phone’s name you wantto change. Follow the HFLprompts and rename the phone.
Press and release the HFL Talkbutton before a command.
Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’
Say ‘‘ ’’ after the prompts.
HFL will ask you which phone youwant to delete. Follow the HFLprompts to continue with thedeletion.
Press and release the HFL Talkbutton before a command.
HFL will read out all the pairedphone’s names.
Say ‘‘ ’’ after the prompts.
Say ‘‘ .’’1.
2.
3. 3.
1.
2.1.
2.
3.
Phone setup
Edit
Phone setup
DeleteList
Phone setup
To hear the names ofall paired phones:
To rename a paired phone: To delete a paired phone:
Bluetooth HandsFreeLink (Models without navigation system)
232
12/07/13 17:06:09 31TM8630_237
Features
TOC
2013 Insight
Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’
Say ‘‘ ’’ after the prompts.
HFL will tell you which phone islinked to the system.
Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’Say ‘‘ .’’
Press and release the HFL Talkbutton before a command.
Say ‘‘ ’’ after theprompts.
HFL disconnects the linked phoneand searches for another pairedphone.
Once another phone is found, it islinked to the system. HFL willinform you which phone is nowlinked.
If no other phones are found orpaired, HFL will inform you that theoriginal phone is linked again.
Say ‘‘ ’’ after theprompts.
If you want HFL to create arandom code each time you pair aphone, say ‘‘ .’’ If you wantto choose your own 4-digit code tobe used each time, say ‘‘ ’’and follow the HFL prompts.
1.
2.
3.
1.
2.
3.
1.
2.
3.
4.
To hear which paired phone iscurrently linked:
To change from the currently linkedphone to another paired phone:
To change the pairing code setting:
Phone setup
Status
Phone setupPhone setup
Next phoneSet pairing code
Random
Fixed
Bluetooth HandsFreeLink (Models without navigation system)
233
12/07/13 17:06:21 31TM8630_238
Features
TOC
2013 Insight
HFL uses a Class 2 Bluetooth, whichmeans, the maximum range betweenyour phone and vehicle is 30 feet
During a call, HFL allows you to talkup to 30 minutes after you removethe key from the ignition switch.However, this may weaken thevehicle’s battery.
You can make calls using a name inthe HFL phonebook or any phonenumber. You can also redial the lastnumber called.
Once connected, you will hear theperson you called through theaudio speakers.
Say ‘‘ ’’ or ‘‘ .’’
Follow the HFL prompts and saythe name stored in the HFLphonebook that you want to call.
Follow the HFL prompts toconfirm the name and make
Say ‘‘ ’’ or ‘‘ .’’
Follow the HFL prompts and saythe phone number you want to dial.
Follow the HFL prompts toconfirm the number and say‘‘ ’’ or ‘‘ .’’
Press and release the HFL Talkbutton before a command.
Press and release the HFL Talkbutton before a command.
1.
2.
3.
1.
2.
3.
Making a Call
Call Dial Call Dial
Call Dial
To make a call using a name in theHFL phonebook:
To make a call using a phonenumber:
Bluetooth HandsFreeLink (Models without navigation system)
234
12/07/13 17:06:32 31TM8630_239
Features
TOC
the call.
(10 meters).
2013 Insight
Press and release the HFL Talkbutton and say ‘‘ .’’
When you receive a call, an incomingcall notification (if activated) willplay and interrupt the audio systemif it is on.
If your phone has Call Waiting, pressand release the HFL Talk button toput the original call on hold andanswer the incoming call.
To return to the original call, pressthe HFL Talk button again. If youdon’t want to answer the incomingcall, disregard it and continue withyour original call. If you want to hangup the original call and answer thenew call, press the HFL Back button.
Press the HFL Talk button to answerthe call, or the HFL Back button tohang up.
To redial the last numbercalled by HFL:
Call Waiting
Redial
Receiving a Call
Bluetooth HandsFreeLink (Models without navigation system)
235
12/07/13 17:06:39 31TM8630_240
Features
TOC
2013 Insight
#
You can transfer a call from HFLto your phone, or from your phoneto HFL.
Press and release the HFL Talkbutton and say ‘‘ .’’
You can mute your voice to theperson you are talking to during HFL allows you to send numbers or
names during a call. This is usefulwhen you call a menu-driven phonesystem.To mute your voice during a call,
press and release the HFL Talkbutton and say ‘‘ .’’
To unmute your voice, press andrelease the HFL Talk button and say‘‘ ’’ again.
Press and release the HFL Talkbutton before a command.
To send a pound ( ), say‘‘pound.’’ To send a star (*), say ‘‘star.’’
Follow the HFL prompts to sendthe tones and continue the call.
Follow the HFL prompts and saythe name or number you want tosend.
Say ‘‘ .’’1.
2.
3.
Transferring a Call
Transfer
Muting a Call Send Numbers or
Mute
MuteSend
To send a name or numberduring a call:
Bluetooth HandsFreeLink (Models without navigation system)
236
NOTE:
12/07/13 17:06:49 31TM8630_241
Features
TOC
a call.
Names During a Call
2013 Insight
You can store up to 50 names withtheir associated numbers in HFL.The numbers you store can be notonly phone numbers but other types,such as account numbers orpasswords, which can be sent duringa menu-driven call.
Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’
Say ‘‘ ’’ after the prompts.
Say a name you want to list as yourphonebook entry.
Say the number you want to storefor the name entry.
Follow the HFL prompts and say‘‘ ’’ to store the entry.
Avoid using duplicate nameentries.
Avoid using ‘‘home’’ as a nameentry.
It is easier for HFL to recognize amultisyllabic or longer name. Forexample, use ‘‘Peter’’ instead of‘‘Pete,’’ or ‘‘John Smith’’ instead of‘‘John.’’
Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’
Say ‘‘ ’’ after the prompts.
Follow the HFL prompts and saythe name entry you want to edit.
When asked, say the new numberfor that name.
Follow the HFL prompts tocomplete the edit.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5.
CONTINUED
To store a phonebook entry:
To edit the number stored in a name:
Phonebook
Store
Enter
Phonebook
Edit
Phonebook
Bluetooth HandsFreeLink (Models without navigation system)
237
NOTE:
12/07/13 17:07:04 31TM8630_242
Features
TOC
2013 Insight
Press and release the HFL Talkbutton before a command.
Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’
Say ‘‘ ’’ after the prompts.
Say the name you want to deleteand follow the HFL prompts tocomplete the deletion.
Say ‘‘ .’’
Say ‘‘ ’’ after the prompts.
HFL begins reading the names inthe order they were stored.
If you hear a name you want to call,immediately press the HFL Talkbutton and say ‘‘ .’’
Press and release the HFL Talkbutton before a command.
Follow the HFL prompts, select anumber from your cell phone, andsend it to HFL.
Say ‘‘ ’’ after theprompts.
Say ‘‘ .’’
Follow the HFL prompts andname the number, or say‘‘ ’’ if it is not the numberyou want to store.
Follow the HFL prompts if youwant to store another number.
1.
2.
3.
4.
1.
2.
3.
4.
1.
2.
3.
5.
Phonebook
Delete
Phonebook
List
Call
Receive contact
Phonebook
Discard
To delete a name: To list all names in the phonebook: To store a specific phone numberfrom your cell phone directly to theHFL phonebook (available on somephones):
Bluetooth HandsFreeLink (Models without navigation system)
238
12/07/13 17:07:17 31TM8630_243
Features
TOC
2013 Insight
This command group allows youto change or customize HFLbasic settings. Press and release the HFL Talk
button before a command.
Say ‘‘ .’’
Once a passcode is set, youwill need to enter it to use HFL eachtime you start the vehicle. If youforget the code, your dealerwill have to reset it for you, oryou will have to clear the entiresystem (see page ).
Follow the HFL prompts toconfirm the number.
Follow the HFL prompts and saythe 4-digit passcode you want toset.
Say ‘‘ ’’ after the prompts.
1.
2.
3.
4.
241
CONTINUED
System Setup
System setup
Security
To set a 4-digit passcode to lock theHFL system for security purposes:
Bluetooth HandsFreeLink (Models without navigation system)
239
NOTE:
12/07/13 17:07:25 31TM8630_244
Features
TOC
2013 Insight
*
*
If you get into the vehicle while youare on the phone, the call can beautomatically transferred to HFLwith the ignition switch in theACCESSORY (I) or ON (II) position.
Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’
Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’
Follow the HFL prompts toconfirm the number.
Follow the HFL prompts and saythe new 4-digit passcode.
Say ‘‘ ’’ after theprompts.
The default setting is a ring tone.
Follow the HFL prompts and say‘‘ ’’ or ‘‘ .’’ Youcan also say ‘‘ ’’ for no audibleincoming call notification.
Say ‘‘ ’’ after theprompts.
HFL will let you know if autotransfer is on or off, depending onthe previous setting. Follow theHFL prompts to change thesetting.
Say ‘‘ ’’ after theprompts.
2.
3.
4.
1.
2.
3.
1.
2.
3. 1.
:
System setup
System setup
System setupChange passcode
Ring tone PromptOff
Call notif ication
Auto transfer
To change your security passcode: To select either a ring tone or aprompt as the incoming callnotif ication :
To activate or deactivate the autotransfer function:
Bluetooth HandsFreeLink (Models without navigation system)
240
12/07/13 17:07:37 31TM8630_245
Features
TOC
2013 Insight
This operation clears the passcodes,paired phones, all names in the HFLphonebook, and all importedphonebook data.
Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’
Say ‘‘ ’’ after the prompts.
Follow the HFL prompts tocontinue to complete the clearingprocedure.
You can also clear the system whenyou have forgotten the passcode andcannot access HFL. When HFL asksyou for the passcode, say ‘‘
.’’ Paired phones, all names inthe HFL phonebook and all importedphonebook data will be lost.
Press and release the HFL Talkbutton before a command.
Follow the HFL prompts.
Say the language you want tochange to in that language.
1.
2.
3.
2.
1.
Canadian models only
System setup
Clear
Systemclear
Quick Language SelectionTo clear the system:
To quickly change the language:
Bluetooth HandsFreeLink (Models without navigation system)
241
12/07/13 17:07:46 31TM8630_246
Features
TOC
2013 Insight
Press and release the HFL Talkbutton before a command.
Say ‘‘ .’’
Follow the HFL prompts tochange the language to English orFrench.
If you have not named your pairedphone in the language you justselected, HFL will ask you to name itin the current language.
When French is your currentlyselected language, you can give voicecommands in French.
The word mark and logosare registered trademarks owned byBluetooth SIG, Inc. and any use ofsuch marks by Honda Motor Co.,Ltd. is under license. Othertrademarks and trade names arethose of their respective owners.
This device complies with theappropriate requirements or therequired standards. See page formore information.
1.
2.
392BluetoothCanadian models only
Bluetooth
To change the system languagebetween English and French:
Wireless TechnologyChange Language
Change language
Bluetooth HandsFreeLink (Models without navigation system)
242
12/07/13 17:07:54 31TM8630_247
Features
TOC
2013 Insight
Before you begin driving yourvehicle, you should know whatgasoline to use and how to checkthe levels of important fluids.You also need to know howto properly store luggage orpackages. The information in this section will help you. Ifyou plan to add any accessories to your vehicle, please read theinformation in this section first.
.............................Break-in Period . 244.................Fuel Recommendation . 244
.........Service Station Procedures . 245....................................Refueling . 245
.....Tighten Fuel Cap Message . 247Opening and Closing the
.......................................Hood . 248...................................Oil Check . 249
.............Engine Coolant Check . 250...............................Fuel Economy . 251
...Accessories and Modifications . 254.............................Carrying Cargo . 256
Before Driving
Before
Driving
243
12/07/13 17:07:58 31TM8630_248
2013 Insight
Help assure your vehicle’s futurereliability and performance by payingextra attention to how you driveduring the first 600 miles (1,000 km).During this period:
Avoid full-throttle starts and rapidacceleration.
You should also follow theserecommendations with anoverhauled or exchanged engine, orwhen the brakes are replaced.
Your vehicle is designed to operateon unleaded gasoline with a pumpoctane number of 87 or higher. Useof a lower octane gasoline can causea persistent, heavy metallic rappingnoise that can lead to engine damage.
Do not change the oil until thescheduled maintenance time.
Avoid hard braking for the first200 miles (300 km).
Use of gasoline with these additivesmay adversely affect performance,and cause the malfunction indicatorlamp on your instrument panel tocome on. If this happens, contactyour dealer for service. Somegasoline today is blended withoxygenates such as ethanol. Yourvehicle is designed to operate onoxygenated gasolinecontaining up to 10% ethanol byvolume. Do not use gasolinecontaining methanol. If you noticeany undesirable operatingsymptoms, try another servicestation or switch to another brand of gasoline.
Break-in Period Fuel Recommendation
Break-in Period, Fuel Recommendation
244
To help prevent harmf ul f uel systemand engine deposits, use high qualityf uel containing detergent and additives.In addition, in order to maintain goodperf ormance, f uel economy, andemissions control, we stronglyrecommend the use of gasoline thatdoes NOT contain harmf ul manganese-based f uel additives such as MMT, ifsuch gasoline is available.
12/07/13 17:08:06 31TM8630_249
Before
Driving
TOC
2013 Insight
CONTINUED
Outside of the vehicle, push on theright side edge of the fuel fill doorin the middle until you hear a click.The fuel fill door will pop upslightly. Pull it outward to open it.
Park with the driver’s side closestto the service station pump.
Because the level of detergency andadditives in gasoline vary in themarket, Honda endorses the use of‘‘TOP TIER Detergent Gasoline’’where available to help maintain theperformance and reliability of yourvehicle. TOP TIER DetergentGasoline meets a new gasolinestandard jointly established byleading automotive manufacturers tomeet the needs of today’s advancedengines. Qualifying gasoline retailerswill, in most cases, identify theirgasoline as having met ‘‘TOP TIERDetergent Gasoline’’ standards at theretail location. This fuel isguaranteed to contain the properlevel of detergent additives and befree of metallic additives. The properlevel of detergent additives, andabsence of harmful metallic additivesin gasoline, help avoid build-up ofdeposits in your engine and emissioncontrol system.
For further important fuel-relatedinformation for your vehicle, orinformation on gasoline that does notcontain MMT, visit Owner Link at
. In Canada, visitfor additional
information on gasoline. For moreinformation on top tier gasoline, visit
1.
2.
owners.honda.comwww.honda.ca
www.toptiergas.com.
Refueling
Fuel Recommendation, Service Station Procedures
245
Push
FUEL FILL DOOR
12/07/13 17:08:13 31TM8630_250
Before
Driving
TOC
2013 Insight
Stop filling the tank after the fuelnozzle automatically clicks off. Donot try to ‘‘top off’’ the tank. Thisleaves some room in the fuel tankfor the fuel to expand withtemperature changes.
If the fuel nozzle keeps clicking offeven though the tank is not full,there may be a problem with yourvehicle’s fuel vapor recoverysystem. The system helps keepfuel vapor from going into theatmosphere. Try filling at anotherpump. If this does not fix theproblem, consult your dealer.
Remove the fuel fill cap slowly.You may hear a hissing sound aspressure inside the tankequalizes. The fuel fill cap is attached to the fuel filler with atether. Place the cap in theholder on the fuel fill door.
3.
4.
Service Station Procedures
246
TETHER
HOLDER FUEL FILL CAPGasoline is highly flammableand explosive. You can beburned or seriously injuredwhen handling fuel.
Stop the engine, and keepheat, sparks, and flame away.Handle fuel only outdoors.Wipe up spills immediately.
12/07/13 17:08:19 31TM8630_251
Before
Driving
TOC
2013 Insight
Your vehicle’s on board diagnosticsystem will detect a loose or missingfuel fill cap as an evaporative systemleak. The first time a leakis detected a ‘‘TIGHTEN FUELCAP’’ message appears on the multi-information display.
Turn the engine off, and confirm thefuel fill cap is installed. If it is, loosenit, then retighten it until it clicks atleast once. The message should gooff after several days of normaldriving once you tighten or replacethe fuel fill cap. To scroll to anothermessage, press the INFO button.
The ‘‘TIGHTEN FUEL CAP’’message will appear each time yourestart the engine until the systemturns the message off.
Screw the fuel fill cap back onuntil it clicks at least once. If youdo not properly tighten the cap,you will see a ‘‘TIGHTEN FUELCAP’’ message on the multi-information display. If the systemstill detects an evaporative systemleak after retightening the cap, themalfunction indicator lamp maycome on (see page ).
Push the fuel fill door closed untilit latches.
6.
5.
365
CONTINUED
Tighten Fuel Cap Message
Service Station Procedures
247
12/07/13 17:08:26 31TM8630_252
Before
Driving
TOC
2013 Insight
Park the vehicle, and set theparking brake. Pull the hoodrelease handle located under thelower left corner of the dashboard.The hood will pop up slightly.
If the system still detects a leak inthe vehicle’s evaporative emissionssystem, the malfunction indicatorlamp (MIL) comes on. If the fuel fillcap was not already tightened, turnthe engine off, and check orretighten the fuel fill cap until itclicks at least once. The MIL shouldgo off after several days of normaldriving once the cap is tightened orreplaced. If the MIL does not go off,have your vehicle inspected by adealer. For more information, seepage .
If the hood latch handle movesstiffly, or if you can open thehood without lifting the handle,the mechanism should becleaned and lubricated.
Put your fingers under the frontedge of the hood near the center.Slide your hand to the left untilyou feel the hood latch handle.Push this handle to the left torelease the hood. Lift up the hood.
1.2.365
Opening and Closing the Hood
Service Station Procedures
248
LATCH
HOOD RELEASE HANDLE
Pull
12/07/13 17:08:33 31TM8630_253
Before
Driving
TOC
2013 Insight
Insert the dipstick all the way backinto its hole.
Wipe off the dipstick with a cleancloth or paper towel.
Remove the dipstick (orange loop).
Wait a few minutes after turning theengine off before you check the oil.
To close the hood, lift it up slightly toremove the support rod from thehole. Put the support rod back intoits holding clip. Lower the hood toabout a foot (30 cm) above thefender, then let it drop. Make sure itis securely latched.
Holding the grip, pull the supportrod out of its clip. Insert theend into the designated holein the hood.
2.
3.
1.
3.
CONTINUED
Oil Check
Service Station Procedures
249
SUPPORT ROD CLIP
GRIP
DIPSTICK
12/07/13 17:08:41 31TM8630_254
Before
Driving
TOC
2013 Insight
Refer toon page for information
about checking other items on yourvehicle.
Look at the coolant level in theradiator reserve tank. Make sure it isbetween the MAX and MIN lines. Ifit is below the MIN line, see
on page forinformation on adding the propercoolant.
Remove the dipstick again, andcheck the level. It should bebetween the upper and lowermarks.
If it is near or below the lower mark,see on page .
4.
310315
307Owner’s Maintenance
ChecksEngine Coolant Check
AddingEngine Coolant
Adding Engine Oil
Service Station Procedures
250
LOWER MARK
UPPER MARK
RESERVE TANK
MIN
MAX
12/07/13 17:08:49 31TM8630_255
Before
Driving
TOC
2013 Insight
-
-
-
-
Fuel economy is not a fixed number.It varies based on driving conditions,driving habits, and vehicle condition.Therefore, it is not possible for oneset of estimates to predict fueleconomy precisely for all drivers inall environments.
The EPA fuel economy estimatesshown in the example to the rightare a useful tool for comparisonwhen buying a vehicle. EPAestimates include: Represents a combination of city and
highway driving. The scalerepresents the range of combinedfuel economy for other vehicles inthe class.
Represents amixture of rural and interstatedriving, in a warmed-up vehicle,typical of longer trips in free-flowingtraffic. A range of miles per gallonachieved is also provided.
Represents urbandriving in light traffic. A range ofmiles per gallon achieved is alsoprovided.
Provides an estimated annual fuelcost, based on 15,000 miles (20,000km) per year multiplied by the cost
per gallon (based on EPA fuel costdata) divided by the combined fueleconomy.
For more information on fueleconomy ratings and factors thataffect fuel economy, visit
(Canada: Visit )
www.fueleconomy.gov
www. vehicles.gc.ca
Actual Mileage and EPA FuelEconomy Estimates Comparison.
Combined Fuel Economy
Highway MPG
City MPG
Estimated Annual Fuel Cost
Fuel Economy
251
Combined FuelEconomy
(Sample U.S. EPA label shown)
Estimated AnnualFuel Cost
City MPG Highway MPG
12/07/13 17:08:57 31TM8630_256
Before
Driving
TOC
2013 Insight
-
-
-
-
-
-
Aggressive driving (hardacceleration and braking)
Excessive idling, accelerating andbraking in stop-and-go trafficCold engine operation (enginesare more efficientwhen warmed up)Driving with a heavy load or theair conditioner runningImproperly inflated tires
The following factors can lower yourvehicle’s fuel economy:
A properly maintained vehiclemaximizes fuel economy. Poormaintenance can significantly reducefuel economy. Always maintain yourvehicle according to the maintenancemessages displayed on the multi-
information display (seeon page ).
For example:Rapid
acceleration, abrupt cornering,and hard braking increase fuelconsumption.
Aerodynamic drag has a big effecton fuel economy at speeds above45 mph (75 km/h). Reduce yourspeed and you reduce the drag.Trailers, car top carriers, roofracks and bike racks are also bigcontributors to increased drag.
An underinflated tire increases‘‘rolling resistance,’’ which reducesfuel economy.
It puts a heavierload on the engine, increasing fuelconsumption.
Inparticular, a build-up of snow ormud on your vehicle’s undersideadds weight and rolling resistance. Frequent cleaning helps your fuel economy.
Idlingresults in 0 miles per gallon (0 kmsper liter).
Use the ECON mode as much aspossible.
307Fuel Economy Factors
Use the recommended viscosity motor oil, displayingthe API Certif ication Seal(see page ).
Improving Fuel Economy
Owner’sMaintenance Checks Drive moderately
Observe the speed limit
Maintain proper tire inflation
Avoid carrying excess weight inyour vehicle
Keep your vehicle clean
Avoid excessive idling
311
Vehicle Maintenance
Drive Efficiently
Fuel Economy
252
12/07/13 17:09:10 31TM8630_257
Before
Driving
TOC
2013 Insight
-
-
Fill the fuel tank until the nozzle automatically clicks off.Reset trip counter to zero.Record the total gallons (liters) needed to refill.Follow one of the simple calculations above.
The A/Cputs an extra load on the enginewhich makes it use more fuel. Usethe fresh-air ventilation whenpossible.
Direct calculation is therecommended source of informationabout your actual fuel economy.Using frequency of fill-ups or takingfuel gauge readings are NOTaccurate measures of fuel economy.Fuel economy may improve over thefirst several thousand miles(kilometers).
Combine several short trips intoone. A warmed-up engine is morefuel efficient than a cold one.
1)2)3)4)
Checking Your Fuel Economy
Measuring Techniques
Minimize the use of the airconditioning system
Calculating Fuel Economy
Plan and combine trips
Fuel Economy
253
Milesdriven
Gallonsof fuel
Miles perGallon
100 KilometersL per
100 kmLiter
12/07/13 17:09:19 31TM8630_258
Before
Driving
TOC
2013 Insight
Your dealer has Honda accessoriesthat allow you to personalize yourvehicle. These accessories havebeen designed and approved for yourvehicle, and are covered by warranty.
Before installing any accessory:
When properly installed, cellularphones, alarms, two-way radios, andlow-powered audio systems shouldnot interfere with your vehicle’scomputer controlled systems, suchas your airbags, anti-lock brakes,and tire pressure monitoring system (if equipped).
Do not install accessories on theside pillars or across the rearwindows. Accessories installed inthese areas may interfere withproper operation of the sidecurtain airbags.
Before installing any electronicaccessory, have the installercontact your dealer for assistance.If possible, have your dealerinspect the final installation.
Be sure electronic accessories donot overload electrical circuits(see page ) or interfere with the proper operation ofyour vehicle.
Make sure the accessorydoes not obscure any lights, orinterfere with proper vehicleoperation or performance.
Although non-Honda accessoriesmay fit on your vehicle, they may notmeet factory specifications, andcould adversely affect your vehicle’shandling, stability, and reliability.
Modifying your vehicle, or installingnon-Honda accessories, may makeyour vehicle unsafe. Before youmake any modifications or add anyaccessories, be sure to read thefollowing information.
367
Accessories
Accessories and Modifications
254
Improper accessories ormodifications can affect yourvehicle’s handling, stability, andperformance, and cause acrash in which you can be hurtor killed.
Follow all instructions in thisowner’s manual regardingaccessories and modifications.
12/07/13 17:09:27 31TM8630_259
Before
Driving
TOC
2013 Insight
*
*
Some examples are:
Removing parts from your vehicle,or replacing components withnon-Honda components couldseriously affect your vehicle’shandling, stability, and reliability.
If you plan to modify your vehicle,consult your dealer.
Modifying your steering wheel orany other part of your vehicle’ssafety features can make thesystems ineffective.
Larger or smaller wheels and tirescan interfere with the operation ofyour vehicle’s anti-lock brakes andother systems.
Non-Honda wheels, because theyare a universal design, can causeexcessive stress on suspensioncomponents and will not becompatible with the tire pressuremonitoring system (TPMS) .
Raising your vehicle with anon-Honda suspension kit canaffect the handling, stability, andreliability.
Lowering your vehicle with anon-Honda suspension kit thatsignificantly reduces groundclearance can allow theundercarriage to hit speed bumpsor other raised objects, whichcould cause the airbags to deploy.
: U.S. models
Modifying Your Vehicle
Accessories and Modifications
255
12/07/13 17:09:35 31TM8630_260
Before
Driving
TOC
2013 Insight
*
*
*
*
*
*
*
* *
Your vehicle has several convenientstorage areas:
Glove box
Door pockets
Cargo area
Center trayFloor storage compartmentUnder floor storage
However, carrying too much cargo,or improperly storing it, can affectyour vehicle’s handling, stability,stopping distance, and tires, andmake it unsafe. Before carrying anytype of cargo, be sure to read thefollowing pages.
Console compartment
Seat-back pockets
Center pocket(s)
: If equipped
Carrying Cargo
256
CARGO AREA
DOOR POCKETS
GLOVE BOX
FLOOR STORAGECOMPARTMENT
UNDER FLOORSTORAGE
SEAT-BACKPOCKETS
CONSOLE COMPARTMENT
: If equippedEX with navigation system model is shown.
CENTER POCKET
CENTER TRAY /CENTER POCKET
12/07/13 17:09:44 31TM8630_261
Before
Driving
TOC
2013 Insight
- ×
-
The resulting figure equals theavailable amount of cargo andluggage load capacity. Forexample, if the ‘‘XXX’’ amountequals 1,400 lbs. and there will befive 150 lb. passengers in yourvehicle, the amount of availablecargo and luggage load capacity is650 lbs.(1,400 750 (5 150) = 650 lbs.)
Determine the combined weightof luggage and cargo being loadedon the vehicle. That weight maynot safely exceed the availablecargo and luggage load capacitycalculated in Step 4.
If your vehicle will be towing atrailer, load from your trailer willbe transferred to your vehicle.Consult this manual to determinehow this reduces the availablecargo and luggage load capacity ofyour vehicle.
Subtract the combined weight ofthe driver and passengers fromXXX kg or XXX lbs.
Locate the statement ‘‘Thecombined weight of occupants andcargo should never exceed XXXkg or XXX lbs.’’ on your vehicle’splacard.
Steps for Determining Correct Load Limit
Determine the combined weightof the driver and passengers thatwill be riding in your vehicle.
The maximum load for your vehicleis 850 lbs (385 kg).
See Tire And Loading Informationlabel attached to the driver’sdoorjamb.
Label Example
This figure includes the total weightof all occupants, cargo, andaccessories, and the tongue load ifyou are towing a trailer.
(1)
(2)
(3)
(6)
(5)
(4)
CONTINUED
Load Limits
Carrying Cargo
257
Overloading or improperloading can affect handling andstability and cause a crash inwhich you can be hurt or killed.
Follow all load limits and otherloading guidelines in thismanual.
12/07/13 17:09:55 31TM8630_262
Before
Driving
TOC
2013 Insight
In addition, the total weight of thevehicle, all occupants, accessories,cargo, and trailer tongue load mustnot exceed the Gross VehicleWeight Rating (GVWR) or theGross Axle Weight Rating (GAWR). Both are on a label on the driver’s doorjamb.
Example 1
Example 2
Example 3
Carrying Cargo
258
Max Load 850 lbs(385 kg)
Max Load 850 lbs(385 kg)
Max Load 850 lbs(385 kg)
Cargo Weight250 lbs(113 kg)
Cargo Weight100 lbs(45 kg)
Passenger Weight150 lbs x 2 = 300 lbs(68 kg x 2 = 136 kg)
Passenger Weight150 lbs x 4 = 600 lbs(68 kg x 4 = 272 kg)
Passenger Weight150 lbs x 5 = 750 lbs(68 kg x 5 = 340 kg)
Cargo Weight550 lbs(249 kg)
12/07/13 17:10:01 31TM8630_263
Before
Driving
TOC
2013 Insight
Store or secure all items that couldbe thrown around and hurtsomeone during a crash.
Be sure items placed on the floorbehind the front seats cannot rollunder the seats and interfere withthe driver’s ability to operate thepedals, the operation of the seats,or the operation of the sensorsunder the seats.
Keep the glove box closed whiledriving. If it is open, a passengercould injure their knees during acrash or sudden stop.
Distribute cargo evenly on thefloor of the hatch, placing theheaviest items on the bottom andas far forward as possible.
Try to secure the items with ropeor cord so they will not shift whileyou are driving.
If you carry large items thatprevent you from closing thehatch, exhaust gas can enter thepassenger area. To avoid thepossibility of
, follow the instructionson page .
If you fold the rear seats down, tiedown items that could be thrownabout the vehicle during a crash orsudden stop. Keep all cargo belowthe bottom of the windows. If it ishigher, it could interfere withproper operation of the sidecurtain airbags.
Refer to page for folding rearseats.
Do not stack items higher than theback of the rear seats. They canblock your view and be thrownaround the vehicle during a crash.
Do not spill any liquids on oraround the IMA battery. Spilledliquids may damage the IMAbattery. If you accidentally spillliquids on or around the battery,ensure that the spill is completelywiped up at the earliest possible time.
56
145
Carrying Items in the Passenger Compartment
Carrying Cargo in the Cargo Area
carbon monoxidepoisoning
Carrying Cargo
259
12/07/13 17:10:10 31TM8630_264
Before
Driving
TOC
2013 Insight
Do not spill any liquids over the airintake or insert any foreign objectsin it. This may damage the IMAbattery and the power control unit.
The air intake for the IMA batteryand electronics is located on the rearleft pillar. Do not block this air intake.Doing so may cause the IMA batteryand the power control unit tooverheat, causing the IMA to shutdown. It will start working againafter it cools.
Air Intake
Carrying Cargo
260
AIR INTAKE
12/07/13 17:10:14 31TM8630_265
Before
Driving
TOC
2013 Insight
This section gives you tips onstarting the engine under variousconditions, and how to operate theautomatic transmissions (CVT). Italso includes important informationon parking your vehicle, the brakingsystem, the vehicle stability assist(VSA ) system, and the tire pressuremonitoring system (TPMS).
........................Preparing to Drive . 262.......................Starting the Engine . 263........................Eco Assist System . 264
.Automatic Transmission (CVT) . 271Driving with the Paddle
.......................................Shifters . 276................................Auto Idle Stop . 281
...........................................Parking . 284.............................Braking System . 285
...............Anti-lock Brakes (ABS) . 287Tire Pressure Monitoring System
......................................(TPMS) . 289Vehicle Stability Assist (VSA ),
aka Electronic Stability....Control (ESC), System . 293
...........Hill Start Assist System . 295...........................Towing a Trailer . 296
Driving
261
12/07/13 17:10:18 31TM8630_266
Before
Driving
2013 Insight
Make sure all windows, mirrors,and outside lights are clean andunobstructed. Remove frost, snow,or ice.
Check that any items you may becarrying are stored properly orfastened down securely.
Check the seat adjustment (seepage ).
Check the adjustment of theinside and outside mirrors (seepage ).
Check the steering wheeladjustment (see page ).
Make sure the doors are securelyclosed and locked.
Fasten your seat belt. Check thatyour passengers have fastenedtheir seat belts (see page ).
You should do the following checksand adjustments before you driveyour vehicle.
Visually check the tires. If a tirelooks low, use a gauge to check itspressure (see page ).
Check that the hood and hatch arefully closed.
When you start the engine, checkthe gauges and indicators in theinstrument panel, and themessages on the multi-informationdisplay (see pages , and ).
1.
2.
3.
8.
7.
6.
9.4.
5.
61 72
17
10.141
147
128
89
338
Preparing to Drive
262
12/07/13 17:10:27 31TM8630_267
Before
Driving
TOC
2013 Insight
Apply the parking brake.
In cold weather, turn off allelectrical accessories to reducethe drain on the battery.
In cold weather, the conventionalstarter is used instead of the IMAsystem starter. This is normal.
Make sure the shift lever is inPark. Press on the brake pedal.
Without touching the acceleratorpedal, turn the ignition key to theSTART (III) position. Do not holdthe key in the START (III)position for more than 15 secondsat a time. If the engine does notstart right away, pause for at least10 seconds before trying again.
1.
2.
3.
4.
Starting the Engine
Starting in Cold Weather
263
The engine is harder to start in coldweather. Also, the thinner air f ound ataltitudes above 8,000 f eet (2,400meters) adds to this problem.
The immobilizer system protects yourvehicle f rom thef t. If an improperlycoded key (or other device) is used, theengine’s f uel system is disabled. Formore inf ormation, see page .130
12/07/13 17:10:34 31TM8630_268
Before
Driving
TOC
2013 Insight
The multi-information display (seepage ).
Your vehicle’s fuel economy mayimprove more with the ECON modeon (see page ).
The driver feedback information isshown in two locations:
The ambient meter, locatedbehind the speedometer (seepage ).
The system monitors your drivingstyle, and can display how it impactsyour vehicle’s fuel economy. You canthen make adjustments to yourdriving style to maximize fueleconomy. (For additionalinformation on fuel economy, seepage .)
Eco Assist System is a driverfeedback system designed to helpyou develop and maintain a fuelefficient driving style.
72
75
127
251
Eco Assist System
264
ECON BUTTON
ECON MODE INDICATORAmbient Meter
Eco-drive Result
Eco Drive Bar
12/07/13 17:10:41 31TM8630_269
Before
Driving
TOC
2013 Insight
The Eco Drive Bar on the ecologicaldrive display appears on the multi-information display while you drive.
During acceleration, the barextends to the right of thecenter line.
If the bar extends into theInefficient Driving Zones, yourcurrent driving style is notconducive to good fuel economy.
If the bar stays within the EfficientDriving Zones, your currentdriving style is conducive to goodfuel economy.
During deceleration, the barextends to the left of thecenter line.
It is recommended to drive in the Dposition for better fuel efficiency.
CONTINUED
Eco Drive BarDriving StyleSlow, steadyacceleration -maximizes fueleconomySlow deceleration -maximizes fueleconomyModerateacceleration
Moderatedeceleration
Aggressive/Inconsistentacceleration - lowersfuel economyAggressivedeceleration - lowersfuel economy
Eco Drive Bar Eco Drive Bar Examples
Eco Assist System
265
AccelerationMonitor
Inefficient Driving Zone
Center Position
DecelerationMonitor
Inefficient Braking Zone
Efficient Zones
ECO ELEMENTS
EcoDriveBar
12/07/23 10:21:17 31TM8630_270
Before
Driving
TOC
2013 Insight
The Ambient Meter (the lightbehind the speedometer) changescolor to show the effects of yourdriving style. This feature can beturned off (see page ).
Fuel EconomyMeter Background Color
103
Ambient Meter
Eco Assist System
266
AMBIENT METER
U.S. model is shown.
(Background Color)Green
Blue Green
Blue
High
Low
12/07/13 17:11:02 31TM8630_271
Before
Driving
TOC
2013 Insight
-
CONTINUED
A point system is used so you canmonitor your driving style and theimpact on fuel economy. Points are:
Accumulated when your drivingstyle is fuel efficientDeducted when your style is notfuel efficient
Your currenttrip is represented on the ecologicaldrive display, starting without anyleaves on the plants. Leaves thenaccumulate during the current trip,as long as you maintain an economicdriving style.
Eco Assist scoring is displayed onthe multi-information display in thefollowing ways:
Eco Assist Scoring
Real Time Score
Eco Assist System
267
FIRST STAGE THIRD STAGE
PLANT ICON
SECOND STAGE
Real Time Score
With the ignition switch in the ON (II) position
12/07/13 17:11:10 31TM8630_272
Before
Driving
TOC
2013 Insight
-
-
The scorefrom your just completed trip isrepresented on the Eco Score screenby the ‘‘plant’’ icons.
Cumulative, orlifetime trips, which build up overtime, represented by a bar graph atthe bottom of the Eco Score display.
Each time you turn the ignitionswitch to the LOCK (0) position, theEco Score displays for a few secondsto show your current stage andlifetime points.
Drive Cycle Score
Lifetime Points
Eco Assist System
268
STAGE-UPRECOGNITIONICON
When turning off the ignition switch
TROPHY
STAGE-DOWN RECOGNITION ICON
Drive Cycle Score/Lifetime Points
DRIVE CYCLESCORE
LIFETIMEPOINTS
12/07/13 17:11:16 31TM8630_273
Before
Driving
TOC
2013 Insight
There are three Eco stages, with five plants per stage. As you accumulate a specified number ofleaves, you advance from one stageto the next. The plant grows leaves from left to right, orloses them from right to left. Atrophy icon appears once you have reached the maximum third stage score.
Idle durationECON button usageVehicle speedBraking and accelerating
The scoring system for points isbased on:
Stages/Displays and Icons Definition
CONTINUED
A total of two leaves can be put on each plant icon.
A total of four leaves can be added to each plant icon.
A circular shaped icon, which represents a blossom, can beadded on top of each plant icon with four leaves.
An icon appears once you have reached the maximum score foreach stage and are moving up to the next stage. These iconsappear briefly when the ignition switch is turned off.Once the 3rd stage maximum score is reached, the systemcontinues to monitor your driving. If you maintain a fuelefficient driving style, your score remains at the highest stage.If you drive less efficiently, points will be deducted and youmay drop (stage down) to the previous stage.
Real time scores must accumulate over time to result in a stage change. In order to build lifetimepoints and advance to the next stage, you need to keep your efficient driving style every time youmake a trip. It can take several months to move from one stage to the next. Individual results willvary.
Eco Assist System
269
First Stage
Second Stage
Third Stage
Maximum Score Icons
SecondStage
FirstStage
ThirdStage
12/07/13 17:11:28 31TM8630_274
Before
Driving
TOC
2013 Insight
*
*
The following procedure clears allleaves and your lifetime points. Thisprocedure must be followed exactly.
As you progress to a higher level, thesystem monitors your driving stylemore strictly. As a result, you mustfurther refine your driving style tocontinue to move up to the next level.
Turn the ignition switch to the ON(II) position. Confirm that the ECONmode is OFF. If it is OFF, proceed tostep 1. Do run the engine.
The following are some of theconditions that may affectyour score:
Extremely high or low ambienttemperatureInconsistent acceleration use, suchas pumping the pedal repeatedlywithin a short period of timeFrequent use of the climatecontrol systemShort distance trips
If the ECON mode is on, press andrelease the ECON button to turn itoff. You also need to turn the ignitionswitch off.
Turn the ignition switch to the ONDo run
Press and release the brakepedal at least two times. Theambient meter colorchanges from blue to green .
Complete the following steps within30 seconds:
The ambient meter color changes onlyif the multi- information display’s meter color change setting is on. (Seepage .)
Press and release the ECONbutton two times (ECON modecomes on, then goes off). Theambient meter color goes off, andthe accumulated data is cleared.
Turn the ignition switch to theLOCK (0) position.
:
1.
2.
3.
103
Reset the System
not
not
Eco Assist System
270
12/07/13 17:11:39 31TM8630_275
Before
Driving
TOC
ON (II) position again.the engine.
2013 Insight
Honda’s Continuously VariableTransmission’s unique designprovides a smooth, constant flow ofpower. It is electronically controlledfor more precise operation andbetter fuel economy.
These indicators on the instrumentpanel show which position the shiftlever is in.
The ‘‘D’’ indicator comes on for afew seconds when you turn theignition switch to the ON (II)position. If it flashes while driving (inany shift position), it indicates apossible problem in the transmission.
If the malfunction indicator lampcomes on along with the ‘‘D’’indicator, there is a problem with theautomatic transmission controlsystem. Avoid rapid acceleration, andhave the transmission checked byyour dealer as soon as possible.When the ‘‘D’’ indicator warns of apossible problem with thetransmission, you will see a ‘‘CHECKTRANSMISSION’’ message on themulti-information display.
Continuously VariableTransmission (CVT)
Shift Lever Position Indicators
Automatic Transmission (CVT)
271
EX models
Insight and LX models
12/07/13 17:11:46 31TM8630_276
Before
Driving
TOC
2013 Insight
To shift from Park to any position,press the brake pedal, the releasebutton on the front of the shift lever,then pull the lever. You cannot shiftout of Park when the ignition switchis in the LOCK (0) or theACCESSORY (I) position.
To shift from:
P to R
R to PN to RD to SS to DD to NN to DR to N
Do this:Press the brake pedal andpress the release button.
Press the release button.
Move the lever.
To shift from:P to R
R to PN to RD to SS to LL to SS to DD to NN to DR to N
Do this:Press the brake pedal andpress the release button.
Press the release button.
Move the lever.
EX modelsInsight and LX modelsShifting
Automatic Transmission (CVT)
272
12/07/13 17:11:52 31TM8630_277
Before
Driving
TOC
2013 Insight
--
-
-
-
CONTINUED
Use this position foryour normal driving. Thetransmission automatically adjusts tokeep the engine at the best speed fordriving conditions. To help theengine warm up faster, thetransmission will select ratios thatallow the engine to run at higherspeeds when it is cold.
Press the brakepedal and the release button on thefront of the shift lever to shift fromPark to reverse. To shift fromreverse to neutral, come to acomplete stop, and then shift. Pressthe release button before shiftinginto reverse from neutral.
Use Neutral if youneed to restart a stalled engine or ifit is necessary to stop briefly withthe engine idling. Always shift to thePark position if you need to leave thevehicle for any reason. Press on thebrake pedal when you are movingthe shift lever from Neutral toanother position.
This position mechani-cally locks the transmission. UsePark whenever you are turning off orstarting the engine. To shift out ofPark, you must press on the brakepedal and have your foot off theaccelerator pedal. Press the releasebutton on the front of the shift leverto move it.
If you have done all of the above andstill cannot move the lever out ofPark, see onpage .
You must also press the releasebutton to shift into Park. To avoidtransmission damage, come to acomplete stop before shifting intoPark. The shift lever must be in Parkbefore you can remove the key fromthe ignition switch.
To shift into the Sposition, press the release button onthe front of the shift lever, and movethe lever to S. Selecting Secondshifts the transmission into a lowerrange of ratios for betteracceleration and increased enginebraking. Use Second when you aregoing down a steep hill.
275
Insight and LX models
Automatic Transmission (CVT)
Drive (D)Reverse (R)
Neutral (N)
Park (P)
Shift Lock ReleaseSecond (S)
273
12/07/13 17:11:59 31TM8630_278
Before
Driving
TOC
2013 Insight
-- When the vehicle reaches themaximum speed in any shift position,you may feel the engine cut in andout. This is caused by a limiter (112mph, 180 km/h) in the engine’scomputer controls. The engine willrun normally when you reduce thespeed to below the maximum.
To shift into the Sposition, press the release button onthe front of the shift lever, and movethe lever to S. The S position issimilar to D, except the range ofratios are different for betteracceleration and increasedengine braking.
With the shift lever in D or S, youcan also use the paddle shifters toshift the transmission up or down.With the paddle shifters, you canoperate the transmission much like amanual transmission without aclutch pedal. For more informationon driving with the paddle shifters,see page .
To shift to Low, pressthe release button on the front of theshift lever. Use Low to make betteruse of engine power when climbing,and for maximum engine brakingwhen going down steep hills.
For faster acceleration when in D, S,or L, the transmission willautomatically ‘‘kick down’’ to a lowerrange of ratios by pushing theaccelerator pedal to the floor.
276
EX modelsInsight and LX models
Automatic Transmission (CVT)
Second (S)Low (L)Speed Limiter
274
12/07/13 17:12:05 31TM8630_279
Before
Driving
TOC
2013 Insight
If you need to use the shift lockrelease, it means your vehicle isdeveloping a problem. Have itchecked by your dealer.
Push down on the key while youpress the release button on theshift lever and move the shift leverout of Park to neutral.
Insert the key in the shift lockrelease slot.
This allows you to move the shiftlever out of Park if the normalmethod of pushing on the brakepedal and pressing the releasebutton does not work.
Put a cloth on the notch of theshift lock release slot cover toprevent scratches. Using a smallflat-tip screwdriver or a metalfingernail file, carefully pry on thenotch of the cover to remove it.
Remove the key from the ignitionswitch.
Set the parking brake.
Remove the key from the shiftlock release slot, then reinstall thecover. Make sure the notch on thecover is on the left side. Insert thekey into the ignition switch, pressthe brake pedal, and restart theengine.
1.
2.
3.4.
5.
6.
Shift Lock Release
Automatic Transmission (CVT)
275
SHIFT LOCK RELEASE SLOT
RELEASE BUTTON
12/07/13 17:12:13 31TM8630_280
Before
Driving
TOC
2013 Insight
+-
+-
To shift up or down, use the(right) or (left) paddle shifter oneither side of the steering wheel.
Pull the (right) paddle shifter toupshift. Pull (left) to downshift.
When you pull either paddle shifter,the shift indicator shows you theselected speed number.
When you are driving in the Dposition, pulling either paddle shifterswitches from the D-normal shiftmode to the D-paddle shift mode.You can shift the transmission up ordown through seven-stages manuallywith the paddle shifters.
When the transmission returns toordinary automatic transmission(CVT), the displayed shiftindicator disappears.
Downshifting gives you more powerwhen climbing, and provides enginebraking when going down a steep hill.
On EX models
Driving with the Paddle Shifters
Using the Paddle Shifters in theD position (D-Paddle Shift Mode)
276
SHIFT INDICATOR
12/07/13 17:12:20 31TM8630_281
Before
Driving
TOC
2013 Insight
-+
CONTINUED
The transmission control systemmonitors the accelerator pedal useand your driving conditions. Whenyou press the accelerator pedal as inthe normal driving, the systemjudges that you are driving at aconstant cruising speed withoutusing the paddle shifters. Underthese conditions, D-paddle shiftmode is canceled, and thetransmission automaticallyreturns to ordinary automatictransmission (CVT).
Downshifting with the (left)paddle shifter allows you to increasethe engine braking when going downsteep or long hills, and providesmore power when climbing uphills.You can upshift the transmissionmanually to reduce the rpm.
To cancel the D-paddle shift modemanually, pull and hold the sidepaddle shifter until the shift indicatorgoes out.
The transmission remains in theselected speed if you do not accelerate.
Driving with the Paddle Shifters
277
12/07/13 17:12:25 31TM8630_282
Before
Driving
TOC
2013 Insight
Each time you pull either paddleshifter, the transmission shifts onespeed up or down. If you want toshift up or down more than twospeeds, pull the paddle shifter twice,pause, and then pull it again.
The automatic transmission (CVT)will not allow you to shift if:
The transmission downshifts to firstspeed and returns to ordinaryautomatic transmission (CVT) whenthe vehicle comes to a complete stopand the vehicle speed is about 6 mph(10 km/h).
If there is a problem in thetransmission while you are drivingwith the paddle shifters, the Dindicator flashes, the D-paddle shiftmode is canceled, and thetransmission returns to ordinaryautomatic transmission (CVT).
You upshift before the enginespeed reaches the lowestthreshold of the higher speed.
If you try to do this, the shiftindicator will flash the number ofthe lower speed several times,then return to a higher speed.
You downshift before the enginespeed reaches the highestthreshold of the lower speed.
You pull both paddle shifters atthe same time.
You pull one of the two paddleshifters with another paddleshifter being pulled.
Driving with the Paddle Shifters
278
12/07/13 17:12:32 31TM8630_283
Before
Driving
TOC
2013 Insight
+-
-
With the shift lever in the S position,you can select the 7-speed manualshift mode to shift speeds; much like a manual transmission using the paddle shifters, but without aclutch pedal.
When you move the shift lever fromthe ‘‘D’’ to the ‘‘S’’ position and pulleither paddle shifter, the shiftindicator displays ‘‘M’’ along with theselected speed number.
To upshift, pull the (right) paddleshifter. To downshift, pull the(left) paddle shifter.
If you keep depressing theaccelerator pedal without pulling thepaddle shifter, the speed will beautomatically shifted up just beforethe tachometer’s red zone.
The transmission also shiftsautomatically as the vehicle comes toa complete stop. It downshifts to firstspeed when the vehicle speedreaches 6 mph (10 km/h) or less.
Downshifting with the (left)paddle shifter allows you to increasethe engine braking when going downsteep or long hills, and providesmore power when climbing uphills.You can upshift the transmissionmanually to reduce the rpm.
To enter the 7-speed manual shiftmode, press the release button onthe front of the shift lever, move thelever to the S position, then pulleither paddle shifter. To cancel the7-speed manual shift mode andreturn to the ordinary automatictransmission (CVT), move the shiftlever from the S position. Whenmoving the shift lever, be careful notto operate incorrectly. While you aredriving in the 7-speed manual shiftmode, the transmission will notautomatically return to the ordinaryautomatic transmission (CVT). CONTINUED
On EX models
Driving with the Paddle Shifters
Using the Paddle Shifters in the S position (7-Speed ManualShift Mode)
279
SHIFT INDICATOR
‘‘M’’ INDICATOR
12/07/13 17:12:40 31TM8630_284
Before
Driving
TOC
2013 Insight
-
→
→
→
→
→
→
The automatic transmission (CVT)will not allow you to shift if:
You downshift before the enginespeed reaches the highestthreshold of the lower speed.If you try to do this, the shiftindicator will flash the number ofthe lower speed several times,then return to a higher speed.
You upshift before the enginespeed reaches the lowestthreshold of the higher speed.
Drive in the highest speed numberthat lets the engine run andaccelerate smoothly. This will giveyou effective emissions control. Thefollowing shift points arerecommended:
To shift to Low,pull and hold both paddle shifterssimultaneously until you see L in theshift indicator. Use Low to get morepower when climbing, and formaximum engine braking whengoing down steep hills.
Shift up
1 2
2 3
3 4
4 5
5 6
6 7
Normal acceleration
15 mph (24 km/h)
25 mph (40 km/h)
40 mph (64 km/h)
45 mph (72 km/h)
50 mph (81 km/h)
55 mph (89 km/h)
You pull both paddle shifters atthe same time.
You pull one of the two paddleshifters with another paddleshifter being pulled.
Driving with the Paddle Shifters
Recommended Shift Points L (Low) mode
280
12/07/13 17:12:48 31TM8630_285
Before
Driving
TOC
2013 Insight
To help maximize fuel economy,your vehicle has an Auto Idle Stopfunction. Depending onenvironmental conditions and vehicleoperation, the engine will shut offwhen you come to a stop.
The transmission fluidtemperature is low.
When the vehicle is stopped on anincline.
The windshield defroster is on.
The fan speed is selected to high(more than four steps on thehorizontal fan speed indicators).
The IMA battery charge is low.
While the auto idle stop function isactivated, the auto idle stop indicatorin the instrument panel blinks (seepage ).
When the ECON mode is on, theengine is more likely to stop thanwhen it is off (see page ).
The engine will not stop automaticallyunder the following conditions:
The engine automatically stops whenthe vehicle comes to a stop with theshift lever in the D position and thebrake pedal pressed.
The engine may also stop whenvehicle speed drops below 7 mph (11km/h) with the brake pedal pressed.
Vehicle speed does not go above
starting the engine.
The vehicle is stopped with theshift position in P, R, S, or L.
The engine coolant temperatureis low.
The pointer of the charge/assistgauge does not move whenaccelerating or decelerating.
127
283
CONTINUED
Auto Idle Stop
281
12/07/13 17:12:59 31TM8630_286
Before
Driving
TOC
9 mph (15 km/h) after
2013 Insight
The engine coolant temperaturebecomes low.
The pressure on the brake pedal isrepeatedly applied and releasedslightly during a stop.
The ECON button is off, and thedifference between the ambienttemperature and the temperaturesetting of the climate controlsystem becomes significant.
The climate control system startsto dehumidify the interior
The engine automaticallyrestarts when:
The brake pedal is released.
Under the following conditions, theengine restarts even if the brakepedal is pressed:
The shift position is changed to R or L.
The accelerator pedal is pressed
The pressure to the brake pedal isreduced and the vehicle startsmoving while stopped on an incline.
The IMA battery chargebecomes low.
The engine may not stop automaticallyunder the following conditions:
The windshield defroster button is pressed.
The ECON button is off, and thereis a significant difference betweenthe ambient temperature and thetemperature setting of the climatecontrol system.
The climate control system isdehumidifying the air.
The vehicle is stopped by brakingsuddenly.
When the ECON button is on, theengine is more likely to stop. Seepage for the ECON button.127
Auto Idle Stop
282
12/07/13 17:13:10 31TM8630_287
Before
Driving
TOC
2013 Insight
If the auto idle stop function turnsoff the engine for a long time, thecharge of the IMA and 12 voltbatteries becomes low, and theengine may not restart automatically.Always turn the ignition switch tothe LOCK (0) position, set theparking brake, and remove the key ifyou are getting out of the vehicle.
The time that auto idle stop isactivated may be reduced if youoperate the windshield wipers withthe climate control system on.
This indicator blinks when the autoidle stop system is in operation. Ifthe driver’s door is opened while theindicator is blinking, the buzzersounds to notify that the auto idlestop system is active.
Auto Idle Stop Indicator
Auto Idle Stop
283
AUTO IDLE STOP INDICATOR
12/07/13 17:13:16 31TM8630_288
Before
Driving
TOC
2013 Insight
If the vehicle is facing downhill,turn the front wheels toward the curb.
Make sure the parking brake isfully released before driving away.Driving with the parking brakepartially set can overheat ordamage the rear brakes.
Set the parking brake before you putthe transmission in Park. This keepsthe vehicle from moving and puttingpressure on the parking mechanismin the transmission.
Always use the parking brake whenyou park your vehicle. Make surethe parking brake is set firmly, oryour vehicle may roll if it is parkedon an incline.
Place any packages, valuables, etc.in the cargo area or take themwith you.
Turn off the lights.
Make sure the windows are closed.
Lock the doors and the hatch.
If the vehicle is facing uphill,turn the front wheels awayfrom the curb.
Never park over dry leaves, tallgrass, or other flammablematerials. The hot three waycatalytic converter could causethese materials to catch on fire.
Check the indicator on theinstrument panel to verify that thesecurity system is set.
LX and EX models
Parking Tips
Parking
284
12/07/13 17:13:24 31TM8630_289
Before
Driving
TOC
2013 Insight
Your vehicle is equipped with frontdisc brakes. The brakes on the rearwheels are drum. A power assisthelps reduce the effort needed onthe brake pedal. The ABS helps youretain steering control when brakingvery hard.
Resting your foot on the pedal keepsthe brakes applied lightly, builds upheat, reduces their effectiveness andreduces brake pad life. In addition,fuel economy can be reduced. It alsokeeps your brake lights on all thetime, confusing drivers behind you.
Check the brakes after drivingthrough deep water. Apply thebrakes moderately to see if they feelnormal. If not, apply them gently andfrequently until they do. Be extracautious in your driving.
Constant application of the brakeswhen going down a long hill buildsup heat and reduces theireffectiveness. Use the engine toassist the brakes by taking your footoff the accelerator and downshiftingto a lower speed.
Braking System
285
12/07/13 17:13:29 31TM8630_290
Before
Driving
TOC
2013 Insight
The hydraulic system that operatesthe brakes has two separate circuits.Each circuit works diagonally acrossthe vehicle (the left-front brake isconnected with the right-rear brake,etc.). If one circuit should develop aproblem, you will still have brakingat two wheels.
If the brake pads need replacing, youwill hear a distinctive, metallicscreeching sound when you applythe brake pedal. If you do not havethe brake pads replaced, they willscreech all the time. It is normal forthe brakes to occasionally squeal orsqueak when you apply them.
The following features arealso equipped:
With the shift lever in D, S or L, thisfeature applies brake pressurebriefly as you release the brakepedal to prevent the vehicle frommoving unexpectedly.
This feature helps you apply thebrakes with less force during anemergency braking situation.
Creep Aid System
Brake-Assist
Braking System Design Brake Pad Wear Indicators
Braking System
286
12/07/13 17:13:36 31TM8630_291
Before
Driving
TOC
2013 Insight
The anti-lock brake system (ABS)helps prevent the wheels fromlocking up, and helps you retainsteering control by pumping thebrakes rapidly, much faster than aperson can do it.
The electronic brake distribution(EBD) system, which is part of theABS, also balances the front-to-rearbraking distribution according tovehicle loading.
Let the ABS work for you by alwayskeeping firm, steady pressure on thebrake pedal. This is sometimesreferred to as ‘‘stomp and steer.’’
You will feel a pulsation in the brakepedal when the ABS activates, andyou may hear some noise. This isnormal: it is the ABS rapidlypumping the brakes. On drypavement, you will need to press onthe brake pedal very hard before theABS activates. However, you mayfeel the ABS activate immediately ifyou are trying to stop on snow or ice.
If this indicator comes on, the anti-lock function of the braking systemhas shut down. The brakes still worklike a conventional system, butwithout anti-lock. You should haveyour dealer inspect your vehicle assoon as possible.
When the ABS indicator comes on,you will also see a ‘‘CHECK ABSSYSTEM’’ message on the multi-information display.
If the ABS indicator comes on whiledriving, test the brakes as shown onpage .366
You should never pump the brake pedal.
CONTINUED
ABS Indicator
Anti-lock Brakes (ABS)
287
12/07/13 17:13:44 31TM8630_292
Before
Driving
TOC
2013 Insight
If the ABS indicator and the brakesystem indicator come on together,and the parking brake is fullyreleased, the EBD system may alsobe shut down.
Test your brakes as instructed onpage . If the brakes feel normal,drive slowly and have your vehiclerepaired by your dealer as soon aspossible. Avoid sudden hard brakingwhich could cause the rearwheels to lock up and possiblylead to a loss of control.
Always steer moderatelywhen you are braking hard. Severeor sharp steering wheel movementcan still cause your vehicle to veerinto oncoming traffic or off the road.
on loose oruneven surfaces, such as gravel orsuch as trying to take a
corner too fast or making a suddenlane change. Always drive at a
It only helps with steeringcontrol during braking.
366
Important Safety Reminders ABS cannot prevent a loss ofstability.
A vehicle with ABS may require alonger distance to stop
ABS will not prevent a skid thatresults from changing directionabruptly,
ABS does not reduce the time ordistance it takes to stop thevehicle.
Anti-lock Brakes (ABS)
288
12/07/13 17:13:50 31TM8630_293
safe speed for the road andweather conditions.
anti-lock.or snow, than a vehicle without
Before
Driving
TOC
2013 Insight
If you think you can safely drive ashort distance to a service station,proceed slowly to the station, theninflate the tire to therecommended pressure.
Driving on a significantly under-inflated tire causes the tire tooverheat and can lead to tire failure.Under-inflation also reduces fuelefficiency and tire tread life, and mayaffect the vehicle’s handling andstopping ability.
Because tire pressure varies bytemperature and other conditions,the low tire pressure/TPMSindicator may come on unexpectedly.
If the tire is flat, or if the tirepressure is too low to continuedriving, replace the tire with thecompact spare tire (see page ).
When the low tire pressure/TPMSindicator is on, one or more of yourtires is significantly underinflated.You should stop and check yourtires as soon as possible, and inflatethem to the proper pressureas indicated on the vehicle’s tireinformation placard.
Your vehicle is equipped with a tirepressure monitoring system (TPMS)that turns on every time you start theengine and monitors the pressure inyour tires while driving.
Each tire has its own pressuresensor. If the air pressure of a tirebecomes significantly low, thesensor in that tire immediately sendsa signal that causes the low tirepressure/TPMS indicator in theinstrument panel to come on. If thishappens, you will see a ‘‘CHECKTIRE PRESSURE’’ message on themulti-information display.
If you cannot make the low tirepressure/TPMS indicator andmessage on the multi-informationdisplay go out after inflating thetires to the specified values, haveyour dealer check thesystem as soon as possible.
348
CONTINUED
U.S. models only Low Tire Pressure/TPMS Indicator
Tire Pressure Monitoring System (TPMS)
289
12/07/13 17:13:58 31TM8630_294
Before
Driving
TOC
2013 Insight
For example, if you check and fillyour tires in a warm area, then drivein extremely cold weather, the tirepressure will be lower thanmeasured and could be underinflatedand cause the low tire pressure/TPMS indicator to come on. Or, ifyou check and adjust your tirepressure in cooler conditions, anddrive into extremely hot conditions,the tires may become overinflated.However, the low tire pressure/TPMS indicator will not come on ifthe tires are overinflated.
Refer to page for tire inflationguidelines.
Although your tire pressure ismonitored, you must manually checkthe tire pressures monthly.
Each tire, including the spare,should be checked monthlywhen the vehicle is cold, and setto the recommended inflation pressure as specified on the vehicleplacard and in the owner’s manual (see page ).
If there is a problem with the TPMS,you will see the above message onthe multi-information display.
If you see this message, the systemis off and is not monitoring the tirepressures. Have the system checkedby your dealer as soon as possible.
If there is a problem with the TPMS,this indicator begins to flash. It stopsflashing after approximately 1minute, then stays on. You will alsosee a ‘‘CHECK TPMS SYSTEM’’message on the multi-informationdisplay (see TPMS System Failure).
338
339
TPMS System Failure
Tire Pressure Monitoring System (TPMS)
290
12/07/13 17:14:06 31TM8630_295
Before
Driving
TOC
2013 Insight
This indicator and the warningmessage on the multi-informationdisplay will go off, after several miles(kilometers) driving, when the sparetire is replaced with the specifiedregular tire equipped with the tirepressure monitor sensor.
Also, the low tire pressure/TPMSindicator begins to flash, then stayson (see page ).
If the low tire pressure/TPMSindicator comes on, or the multi-information display shows a‘‘CHECK TPMS SYSTEM’’ message,the VSA system automatically turnson even when the VSA system isturned off by pressing the VSA OFFswitch (see page ). If thishappens, you cannot turn the VSAsystem off by pressing the VSA OFFswitch again.
When you restart the vehicle withthe compact spare tire, the TPMSsystem message will also bedisplayed on the multi-informationdisplay after several miles(kilometers) driving.
If you have a flat tire, the low tirepressure/TPMS indicator will comeon. Replace the flat tire with thecompact spare tire (see page ).
After the flat tire is replaced with the spare tire, the low tire pressure/TPMS indicator stays on whiledriving. After several miles(kilometers) driving, this indicatorbegins to flash, then stays on again.You will also see a ‘‘CHECK TPMSSYSTEM’’ message on the multi-information display. This is normal;the system cannot monitor the spare tire pressure. Manually checkthe spare tire pressure to be sure itis correct.
Each wheel (except the compactspare tire wheel) is equipped with atire pressure sensor. You must useTPMS specific wheels. It isrecommended that you always haveyour tires serviced by your dealer orqualified technician.
289
294
349
CONTINUED
Changing a Tire with TPMS
Tire Pressure Monitoring System (TPMS)
291
12/07/13 17:14:13 31TM8630_296
Before
Driving
TOC
2013 Insight
Never use a puncture-repairing agentin a flat tire. If used, you will have toreplace the tire pressure sensor.Have the flat tire repaired by yourdealer as soon as possible.
This device complies with theappropriate requirements or therequired standards. See page formore information.
392
Tire Pressure Monitoring System (TPMS)
292
12/07/13 17:14:17 31TM8630_297
Before
Driving
TOC
2013 Insight
If this indicator comes on whiledriving, pull to the side of the roadwhen it is safe, and turn off theengine. Reset the system byrestarting the engine. If the VSAsystem indicator stays on or comesback on while driving, have the VSAsystem inspected by your dealer.
If the indicator does not come onwhen the ignition switch is turned tothe ON (II) position, there may be aproblem with the VSA system. Haveyour dealer inspect your vehicle assoon as possible.
When VSA activates, you will see theVSA system indicator blink.
The vehicle stability assist (VSA)system helps to stabilize the vehicleduring cornering if the vehicle turnsmore or less than desired. It alsoassists you in maintaining tractionwhile accelerating on loose orslippery road surfaces. It does thisby regulating the engine’s output andby selectively applying the brakes.
When VSA activates, you may noticethat the engine does not respond tothe accelerator in the same way itdoes at other times. There may alsobe some noise from the VSAhydraulic system. You will also seethe VSA activation indicator blink.
The VSA system cannot enhance thevehicle’s driving stability in allsituations and does not control yourvehicle’s entire braking system. It isstill your responsibility to drive andcorner at reasonable speeds and toleave a sufficient margin of safety.
When VSA is off, the VSA OFFindicator comes on as a reminder.
The VSA system indicator will alsocome on when there is a problem inthe hill start assist system. For moreinformation, see page .
The main function of theVSA system is generally known asElectronic Stability Control (ESC).The system also includes a tractioncontrol function.
When the VSA system indicatorcomes on, you will also see a‘‘CHECK VSA SYSTEM’’ or‘‘CHECK HILL START ASSISTSYSTEM’’ message on the multi-information display.
295
Vehicle Stability Assist(VSA) System Indicator
VSA OFF Indicator
Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System
293
NOTE:
12/07/13 17:14:27 31TM8630_298
Before
Driving
TOC
2013 Insight
Immediately after freeing yourvehicle, be sure to switch the VSA onagain. We do not recommend drivingyour vehicle with the VSA andtraction control systems switched off.
In certain unusual conditions whenyour vehicle gets stuck in shallowmud or fresh snow, it may be easierto free it with the VSA temporarilyswitched off. When the VSA systemis off, the traction control system isalso off. You should only attempt tofree your vehicle with the VSA off ifyou are not able to free it when theVSA is on.
VSA is turned on every time youstart the engine, even if you turned it off the last time you drovethe vehicle.
When VSA is off, the VSA activationindicator comes on as a reminder.Press and hold the switch again. Itturns the system back on.
This switch is under the driver’s side vent. To turn the VSA system on and off, press and hold it until you hear a beep.
If the low tire pressure/TPMSindicator comes on (see page ),or the multi-information displayshows a ‘‘CHECK TPMS SYSTEM’’message with the indicator flashing(see page ), the VSA systemautomatically turns on even if theVSA system is turned off with theVSA OFF switch. In this case, youcannot turn the VSA system off bypressing the VSA OFF switch again.
Without VSA, your vehicle will havenormal braking and cornering ability,but it will not have VSA traction andstability enhancement.
289
290
On U.S. models
Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System
VSA OFF Switch
294
VSA OFFSWITCH
12/07/13 17:14:34 31TM8630_299
Before
Driving
TOC
2013 Insight
Driving with varying tire or wheelsizes may cause the VSA tomalfunction. When replacing tires,make sure they are of the same sizeand type as your original tires (seepage ).
If you install winter tires, make surethey are the same size as those thatwere originally supplied with yourvehicle. Exercise the same cautionduring winter driving as you would if your vehicle was notequipped with VSA.
Your vehicle is equipped with a hillstart assist feature to help preventthe vehicle from rolling on inclinesas you move your foot from thebrake pedal to the accelerator.
To activate hill start assist, you mustcome to a complete stop and makesure the shift lever is in any of D, Sor L (either in D or S on models withthe paddle shifters) when facinguphill, or reverse when facingdownhill. Release the brake pedal.The brakes remain engaged brieflyto keep the vehicle from rollingforward or backward whileyou move your foot from the brakepedal to the accelerator pedal.Gently apply the acceleratorpedal as in normal driving. Hill startassist will release brake pressuregradually as you accelerate.
Hill start assist may not prevent yourvehicle from rolling downhill on avery steep or slippery slope, and willnot operate on small inclines.
Hill start assist is not a replacementfor the parking brake. If parkingyour vehicle, ensure that thetransmission is in Park, and theparking brake is fully applied beforeexiting the vehicle. You should alsoturn off the engine beforeexiting the vehicle.
The VSA system indicator will comeon when there is a problem in the hillstart assist system. With the VSAsystem indicator on, the hill startassist system will not activate.
Hill start assist will still operate evenwhen VSA is switched off.
342
Vehicle Stability Assist (VSA ), aka Electronic Stability Control (ESC), System
VSA and Tire Sizes Hill Start Assist System
295
12/07/13 17:14:42 31TM8630_300
Before
Driving
TOC
2013 Insight
Your vehicle is not designed to tow atrailer. Attempting to do so can voidyour warranties.
Towing a Trailer
296
12/07/13 17:14:45 31TM8630_301
Before
Driving
TOC
2013 Insight
This section explains why it isimportant to keep your vehicle wellmaintained and how to follow basicmaintenance safety precautions.
If you have the skills and tools toperform more complex maintenancetasks on your vehicle, you may wantto purchase the service manual. Seepage for information on how toobtain a copy, or see your dealer.
U.S. Vehicles:
This section also includesinstructions on how to read theMaintenance Minder messages onthe multi-information display, andinstructions for simplemaintenance tasks you may wantto take care of yourself.
......................Maintenance Safety . 298.................Maintenance Minder . 299
..............................Fluid Locations . 309........................Adding Engine Oil . 310
.........Changing the Oil and Filter . 312..............................Engine Coolant . 315
....................Windshield Washers . 317....Automatic Transmission Fluid . 318
Continuously Variable............Transmission (CVT) . 318
....................................Brake Fluid . 319.............................................Lights . 321
..............................Audio Antenna . 331................Cleaning the Seat Belts . 331
.....................................Floor Mats . 331..................Dust and Pollen Filter . 332
.................................Wiper Blades . 332...............................................Tires . 338
......Checking the 12 Volt Battery . 344.............................Vehicle Storage . 346
397
Maintenance
Maintenance, replacement, orrepair of emissions controldevices and systems may be doneby any automotive repairestablishment or individual usingparts that are ‘‘certif ied’’ to EPAstandards.
Maintenance
297
TM
12/07/13 17:14:50 31TM8630_302
2013 Insight
To eliminate potential hazards, readthe instructions before you begin,and make sure you have the toolsand skills required.
To clean parts, use a commerciallyavailable degreaser or partscleaner, not gasoline.
To reduce the possibility of fire orexplosion, keep cigarettes, sparks,and flames away from the batteryand all fuel-related parts.
Make sure your vehicle is parkedon level ground, the parking brakeis set, and the engine is off.
Some of the most important safetyprecautions are given here. However,we cannot warn you of everyconceivable hazard that can arise inperforming maintenance. Only youcan decide whether or not youshould perform a given task.
Donot run the engine unlessinstructed to do so.
Let theengine and exhaust system cooldown before touching any parts.
Wear eye protection andprotective clothing when workingwith the battery or compressed air.
All service items not detailed in this section should be performed by a certified technician orqualified mechanic.
Be sure there isadequate ventilation whenever youoperate the engine.
Maintenance Safety
Important Safety PrecautionsInjury from moving parts.
Burns from hot parts.
Carbon Monoxide poison fromengine exhaust.
Potential Vehicle Hazards
298
Failure to properly followmaintenance instructions andprecautions can cause you tobe seriously hurt or killed.
Always follow the proceduresand precautions in this owner’smanual.
Improperly maintaining thisvehicle or failing to correct aproblem before driving cancause a crash in which you canbe seriously hurt or killed.
Always follow the inspectionand maintenancerecommendations andschedules in this owner’smanual.
12/07/13 17:15:00 31TM8630_303
Maintenance
TOC
2013 Insight
------------
The remaining engine oil life isshown on the display according tothis table:
Your vehicle displays engine oil lifeand maintenance service items onthe multi-information display to showyou when you should have yourdealer perform engine oilreplacement and indicatedmaintenance service.
To see the current engine oil lifedisplayed on the multi-informationdisplay, turn the ignition switch tothe ON (II) position, and press theSEL/RESET button on the steeringwheel repeatedly until the engine oillife is displayed.
Based on the engine operatingconditions, the onboard computer inyour vehicle calculates theremaining engine oil lifeand displays it as a percentage.
CONTINUED
DisplayedEngine Oil Life (%)
100%90%80%70%60%50%40%30%20%15%10%5%0%
Calculated EngineOil Life (%)
100% 91%90% 81%80% 71%70% 61%60% 51%50% 41%40% 31%30% 21%20% 16%15% 11%10% 6%5% 1%
0%
Engine Oil Life Display
Maintenance Minder
299
ENGINE OIL LIFE DISPLAY
REMAINING ENGINE OIL LIFE
TM
12/07/13 17:15:07 31TM8630_304
Maintenance
TOC
2013 Insight
▲ ▼
When the remaining engine oil life is15 to 6 percent, the multi-informationdisplay shows a ‘‘SERVICE DUESOON’’ message along with themaintenance item code(s) indicatingthe main and sub items required atthe time of the oil change. Refer topage for a complete list of themaintenance main items and
Pressing either INFO button ( / )switches the display from themessage to another display. Onceyou switch the display, this messagewill go off.
Along with the message, the systemmessage indicator comes on (seepage ).
The message appears on the multi-information display each time youturn the ignition switch to the ON(II) position.
This message reminds you that yourvehicle will soon be due forscheduled maintenance.
Press the SEL/RESET button on thesteering wheel repeatedly to selectthe engine oil life information. Alongwith the ‘‘OIL LIFE’’ message, youwill see the percentage of theremaining engine oil life and themaintenance item codes on themulti-information display.
70
308
Maintenance Minder
300
REMAINING ENGINEOIL LIFE
MAINTENANCE SUB ITEM CODE(S)
MAINTENANCE MAIN ITEM CODE(S)MAIN ITEM(S)
SUB ITEM(S)
TM
12/07/13 17:15:14 31TM8630_305
Maintenance
TOC
sub items.
2013 Insight
-
▲ ▼
When the remaining oil life is 5 to 1percent, the multi-informationdisplay shows a ‘‘SERVICE DUENOW’’ message with the samemaintenance items ‘‘SERVICE DUESOON’’ was displayed with. Whenyou see this message, have theindicated maintenance performed assoon as possible.
Press the SEL/RESET button on thesteering wheel repeatedly to selectthe engine oil life. The message‘‘SERVICE,’’ along with ‘‘5%,’’ and themaintenance item code are displayedon the multi-information displaywhen the calculated engine oil life is1 5 percent (see page ).
Pressing either INFO button ( / )switches the display from themessage to another display. Onceyou switch the display, this messagewill go off.
Along with the message, the systemmessage indicator comes on (seepage ).70
299
CONTINUED
Maintenance Minder
301
TM
12/07/13 17:15:20 31TM8630_306
Maintenance
TOC
2013 Insight
▲ ▼
-
If the indicated maintenance serviceis not done and the remaining engineoil life reaches 0%, the multi-information display will show themessage ‘‘SERVICE PAST DUE’’and the maintenance item code(s).This message is displayed when thetotal distance traveled is less than 10miles (for U.S. models) or 10 km (forCanadian models) after the engineoil life became 0%.
These messages will come on everytime you turn the ignition switch tothe ON (II) position.
Immediately have the serviceperformed, and make sure to resetthe display as described on page .
Pressing either INFO button ( / )switches the display from themessage to another display. To seethe message again, press eitherINFO button repeatedly.
Press the SEL/RESET button on thesteering wheel repeatedly to selectthe engine oil life. The message‘‘SERVICE,’’ along with ‘‘0%,’’ and themaintenance item code are displayedon the multi-information displaywhen the calculated engine oil life is0 1 percent.
Along with the message, the systemmessage indicator comes on (seepage ).70
304
Maintenance Minder
302
TM
12/07/13 17:15:26 31TM8630_307
Maintenance
TOC
2013 Insight
▲ ▼
If the indicated required service isnot done and the remaining engineoil life becomes 0%, the multi-information display will show a‘‘SERVICE PAST DUE’’ message,the total distance traveled after theremaining oil life became 0%, and themaintenance item code(s).
Immediately have the serviceperformed, and make sure to resetthe display as described on page .
Pressing either INFO button ( / )switches the display from themessage to another display. To seethe message again, press eitherINFO button repeatedly. When you press the SEL/RESET
button to select the engine oil life,the message ‘‘SERVICE,’’along with the maintenanceitem code(s) and the total negativedistance traveled after the oil lifebecame 0%, will be displayed on themulti-information display.
This message is displayed againwhen you drive over 10 miles (forU.S. models) or 10 km (for Canadianmodels) after seeing the 0% message.
304
Maintenance Minder
303
U.S.U.S.
NEGATIVE DISTANCE TRAVELED
NEGATIVE DISTANCE TRAVELEDMAINTENANCE ITEM CODE(S)
CanadaCanada
TM
12/07/13 17:15:33 31TM8630_308
Maintenance
TOC
2013 Insight
All the maintenance items displayedin the multi-information display arein code.
For an explanation of themaintenance codes, see page .
Your dealer will reset the displayafter completing the requiredmaintenance service. You will see‘‘OIL LIFE 100%’’ on the display thenext time you turn the ignitionswitch to the ON (II) position.
Turn the ignition switch to the ON(II) position.
If maintenance service is doneby someone other than yourdealer, reset the MaintenanceMinder as follows:
1.
308
Maintenance Main Itemsand Sub
Resetting the Engine OilLife Display
Maintenance Minder
304
ENGINE OIL LIFEDISPLAY
MESSAGEDISPLAY
MAINTENANCESUB ITEMS
MAINTENANCEMAIN ITEM
TM
12/07/13 17:15:42 31TM8630_309
Items
Maintenance
TOC
2013 Insight
▲ ▼
▲ ▼
CONTINUED
Select ‘‘RESET’’ by pressing theINFO ( / ) button, then pressthe SEL/RESET button to resetthe engine oil life display. Themaintenance item code(s) willdisappear, and the engine oil lifewill reset to ‘‘100.’’ If you want tocancel the oil life reset mode,select ‘‘CANCEL.’’
4.
Maintenance Minder
305
INFO BUTTON( / )
SEL/RESETBUTTON
DX model
TM
12/07/13 17:15:48 31TM8630_310
Maintenance
TOC
▲ ▼
If the engine oil life is not displayed,press the SEL/RESET button on thesteering wheel repeatedly.
Press and hold the SEL/RESETbutton on the steering wheel formore than 10 seconds. Theremaining engine oil life resetmode will be shown on the multi-information display.
2.
3.
SEL/RESET BUTTON
INFO BUTTONS ( / )
LX and EX models
2013 Insight
We recommend using Honda partsand fluids whenever you havemaintenance done. These aremanufactured to the same highquality standards as the originalcomponents, so you can be confidentof their performance and durability.
However, service at a dealer is notmandatory to keep your warrantiesin effect. Maintenance may be doneby any qualified service facility orperson who is skilled in this type ofautomotive service. Make sure tohave the service facility or personreset the display as previouslydescribed. Keep all receipts as proofof completion, and have the personwho does the work fill out yourHonda Service History or CanadianMaintenance Log. Check yourwarranty booklet for moreinformation.
Your authorized Honda dealerknows your vehicle best and canprovide competent, efficient service.
Maintenance Minder
306
TM
12/07/13 17:15:52 31TM8630_311
If you have the required servicedone but do not reset the display, orreset the display without doing theservice, the system will not show thecorrect maintenance intervals. Thiscan lead to serious mechanicalproblems because you will no longerhave an accurate record of whenmaintenance is needed.
Important MaintenancePrecautions
Maintenance
TOC
2013 Insight
-
-
-
-
-
#-
You should check the followingitems at the specified intervals. Ifyou are unsure of how to performany check, turn to the appropriatepage listed.
Engine oil level Check everytime you fill the fuel tank. Seepage .
Engine coolant level Check theradiator reserve tank every timeyou fill the fuel tank. See page .
Automatic transmission Checkthe fluid level monthly. Seepage .
Brakes Check the fluid levelmonthly. See page .
Tires Check the tire pressuremonthly. Examine the tread forwear and foreign objects. See
U.S. Vehicles:According to state and federalregulations, failure to performmaintenance on the items markedwith will not void your emissionswarranties. However, allmaintenance services should beperformed in accordance with theintervals indicated by the multi-information display.
Lights Check the operation ofall the lights monthly. See
.
249
250
318
319
338
321
CONTINUED
Owner’s Maintenance Checks
Maintenance Minder
307
TM
12/07/13 17:16:01 31TM8630_312
Maintenance
TOC
page
page .
2013 Insight
*
*
#
#
*
#
Maintenance Minder
308
:
TM
Maintenance Main ItemsReplace engine oilReplace engine oil and oil filterInspect front and rear brakesCheck parking brake adjustmentInspect these items:
Tie rod ends, steering gear box, and bootsSuspension componentsDriveshaft bootsBrake hoses and lines (including ABS/VSA)All fluid levels and condition of fluidsExhaust systemFuel lines and connections
Maintenance Sub ItemsRotate tiresReplace air cleaner element
If you drive in dusty conditions, replace every 15,000miles (24,000 km).
Replace dust and pollen filterIf you drive primarily in urban areas that have highconcentrations of soot in the air from industry andfrom diesel-powered vehicles, replace every 15,000miles (24,000 km).
Inspect drive beltReplace transmission fluidReplace spark plugsInspect valve clearanceReplace engine coolant
AB
Symbol Symbol12
34
5
Inspect idle speed every 160,000 miles (256,000 km).
See information on maintenance and emissions warranty in the first columnon page .
Independent of the Maintenance Minder information, replace the brakefluid every 3 years.
If the message ‘‘SERVICE’’ does not appear more than 12 months after thedisplay is reset, change the engine oil every year.
Adjust the valves during services A, B, 1, 2, or 3 if they are noisy.
NOTE:
:
307
Main
tenance
Min
der
12/07/13 17:16:08 31TM8630_313
TOC
2013 Insight
Fluid Locations
309
RADIATOR CAP
ENGINE OIL DIPSTICK(Orange loop)
AUTOMATICTRANSMISSION (CVT)FLUID DIPSTICK(Yellow loop)
BRAKE FLUID(Black cap)
ENGINE OIL FILL CAP
ENGINE COOLANTRESERVOIR
WASHER FLUID(Blue cap)
12/07/13 17:16:12 31TM8630_314
Maintenance
TOC
2013 Insight
Unscrew and remove the engine oilfill cap on the valve cover. Pour theoil slowly and carefully so you do notspill any. Clean up any spillsimmediately. Spilled oil coulddamage components in the enginecompartment.
Oil is a major contributor to yourengine’s performance and longevity.Always use a premium-grade 0W-20detergent oil displaying the APICertification Seal. This seal indicatesthe oil is energy conserving, and thatit meets the American PetroleumInstitute’s latest requirements.
Reinstall the engine oil fill cap, andtighten it securely. Wait a fewminutes, and recheck the oil level onthe engine oil dipstick. Do not fillabove the upper mark; you coulddamage the engine.
Adding Engine Oil
Recommended Engine Oil
310
ENGINE OIL FILL CAP
12/07/13 17:16:17 31TM8630_315
Maintenance
TOC
2013 Insight
Honda Motor Oil is the preferred0W-20 lubricant for your vehicle. It ishighly recommended that you useHonda Motor Oil in your vehicle foroptimum engine protection. Makesure the API Certification Seal says‘‘For Gasoline Engines’’.
The oil viscosity or weight isprovided on the container’s label. You may use a synthetic motor oil if
it meets the same requirementsgiven for a conventional motor oil: itdisplays the API Certification Sealand it is the proper weight. You mustfollow the oil and filter changeintervals shown on the multi-information display.
Your vehicle does not require any oiladditives. Additives may adverselyaffect the engine or transmissionperformance and durability.
A very low-viscosity, fuel-efficient0W-20 oil is the engine lubricant foryour Insight. This oil is formulated tohelp your engine use less fuel.
Adding Engine Oil
Synthetic Oil
Engine Oil Additives
311
API CERTIFICATION SEAL
Ambient Temperature
12/07/13 17:16:25 31TM8630_316
Maintenance
TOC
2013 Insight
Changing the oil and filter requiresspecial tools and access fromunderneath the vehicle. The vehicleshould be raised on a servicestation- type hydraulic lift forthis service. Unless you have theknowledge and proper equipment,you should have this maintenancedone by a skilled mechanic.
Run the engine until it reachesnormal operating temperature,then shut it off.
Open the hood, and remove theengine oil fill cap.
Remove the screws with a Phillips-head screwdriver, and clips with aflat-tip screwdriver, then pull theunder-cover down.
Always change the oil and filteraccording to the maintenancemessages shown on the multi-information display. The oil and filtercollect contaminants that candamage your engine if they are notremoved regularly.
1.
2.3.
Changing the Oil and Filter
312
SCREW
CLIP
SCREWS
12/07/13 17:16:31 31TM8630_317
Maintenance
TOC
2013 Insight
CONTINUED
Remove the oil drain bolt andwasher from the bottom of theengine. Drain the oil into anappropriate container.
Remove the oil filter, and let theremaining oil drain. A specialwrench (available from yourdealer) is required.
Make sure the oil filter gasket isnot stuck to the contacting surfaceof the engine. If it is, remove itbefore installing a new oil filter.
Engine oil change capacity(including filter):
Refill the engine with therecommended oil.
Put a new washer on the drain bolt,then reinstall the drain bolt.Tighten the drain bolt to:
Make sure to clean off any dirtand dust on the contacting surfaceof a new oil filter.
Install a new oil filter according tothe instructions that come with it.
7.
8.4. 5.
6.
Changing the Oil and Filter
313
WASHER OIL FILTER
BOLT
3.4 US qt (3.2 )
29 lbf·ft (39 N·m , 4.0 kgf·m)
12/07/13 17:16:41 31TM8630_318
Maintenance
TOC
2013 Insight
Turn off the engine, let it sit forseveral minutes, then check the oillevel on the dipstick. If necessary,add more oil.
Put the under-cover back in placeand reinstall the holding clips andscrews. Lock the clips securely bypushing on the center of each clip.
Reinstall the engine oil fill cap.Start the engine. The oil pressureindicator should go out within 5seconds. If it does not, turn off theengine, and check your work.
Let the engine run for severalminutes, then check the drain boltand oil filter for leaks.
9.
10.
11.
12.
Changing the Oil and Filter
314
Improper disposal of engine oil can beharmf ul to the environment. If youchange your own oil, please dispose ofthe used oil properly. Put it in a sealedcontainer and take it to a recyclingcenter. Do not discard it in a trash binor dump it on the ground.
12/07/13 17:16:46 31TM8630_319
Maintenance
TOC
2013 Insight
- -
If the coolant level in the reservetank is at or below the MIN line, addcoolant to bring it up to between theMIN and MAX lines. Inspect thecooling system for leaks.
Always use Honda Long-life Anti-freeze/Coolant Type 2. This coolantis pre-mixed with 50 percentantifreeze and 50 percent distilledwater. Never add straight antifreezeor plain water.
If Honda antifreeze/coolant is notavailable, you may use anothermajor-brand non-silicate coolant as atemporary replacement. Make sureit is a high-quality coolantrecommended for aluminum engines. Continued use of any non-Honda coolant can result in corrosion, causing the cooling system to malfunction or fail. Havethe cooling system flushed and refilled with Honda antifreeze/coolant as soon as possible.
CONTINUED
Adding Engine Coolant
Engine Coolant
315
RESERVE TANK
If you regularly drive your vehicleunder severe conditions in very lowtemperature (under 31°F, 35°C), ahigher concentration of coolant shouldbe used. Consult your Honda dealerf or more inf ormation on the propercoolant.
12/07/13 17:16:53 31TM8630_320
Maintenance
TOC
2013 Insight
If the reserve tank is completelyempty, you should also check thecoolant level in the radiator.
The coolant level should be up tothe base of the filler neck. Addcoolant if it is low.
Do not add any rust inhibitors orother additives to your vehicle’scooling system. They may not becompatible with the coolant orengine components.
Pour coolant into the reserve tank.Fill it to halfway between the MAXand MIN marks. Put the cap backon the reserve tank.
Pour the coolant slowly andcarefully so you do not spill any.Clean up any spill immediately; itcould damage components in theengine compartment.
Put the radiator cap back on, andtighten it fully.
Remove the radiator cap bypushing down and turningcounterclockwise.
Relieve any pressure in the coolingsystem by turning the radiator capcounterclockwise, withoutpressing down.
Make sure the engine and radiatorare cool.
1.
2.
3.
4.
5.
6.
Engine Coolant
316
RADIATOR CAP
Removing the radiator capwhile the engine is hot cancause the coolant to spray out,seriously scalding you.
Always let the engine andradiator cool down beforeremoving the radiator cap.
12/07/13 17:17:02 31TM8630_321
Maintenance
TOC
2013 Insight
Check the fluid level in thewindshield washer reservoir at leastmonthly during normal use.
Check the fluid level byremoving the cap and looking atthe level gauge.
When you refill the reservoir, cleanthe edges of the windshield wiperblades with windshield washer fluidon a clean cloth. This will help tocondition them.
Fill the reservoir with a good-qualitywindshield washer fluid. Thisincreases the cleaning capability andprevents freezing in cold weather.
If the washer fluid is low, a ‘‘WASHERFLUID LOW’’ message appears on themulti-information display.
On U.S. models
On all Canadian models
Windshield Washers
317
Do not use engine antif reeze or avinegar/water solution in thewindshield washer reservoir. Antif reezecan damage your vehicle’s paint, whilea vinegar/water solution can damagethe windshield washer pump. Use onlycommercially-available windshieldwasher f luid.
12/07/13 17:17:09 31TM8630_322
Maintenance
TOC
2013 Insight
Remove the dipstick and checkthe fluid level. There is a HOTside and a COLD side on thedipstick. The fluid level should bebetween the upper and lowermarks on the HOT side.
Remove the dipstick (yellow loop)from the transmission, and wipe itwith a clean cloth.
Insert the dipstick all the way intothe transmission securely asshown in the illustration.
Check the fluid level with the engineat normal operating temperature.
Park the vehicle on level ground.Start the engine, let it run until theradiator fan comes on, then shutoff the engine. For accurateresults, wait about 60 seconds (butno longer than 90 seconds) beforedoing step 2.
3.
4.2.
1.
Continuously VariableTransmission (CVT)
Automatic Transmission Fluid
318
DIPSTICK
HOTRange
UPPERMARK
LOWERMARK
12/07/13 17:17:17 31TM8630_323
Maintenance
TOC
2013 Insight
CONTINUED
Check the brake fluid level in thereservoirs monthly.
You will also see the ‘‘BRAKEFLUID LOW’’ message on the multi-information display when the brakefluid level is low.
Insert the dipstick all the way backinto the transmission securely.
The transmission should be drainedand refilled with new fluid when thisservice is indicated by a maintenancemessage on the multi-informationdisplay.
If you are not sure how to add fluid,contact your dealer.
If the level is below the lowermark, add fluid into the dipstickhole to bring it to the levelbetween the upper and lowermarks.Pour the fluid slowly and carefullyso you do not spill any. Clean upany spill immediately; it coulddamage components in the enginecompartment.Always use Honda CVTF(continuously variabletransmission fluid).
Independent of the MaintenanceMinder information, replace thebrake fluid every 3 years.
6.5.
Automatic Transmission Fluid, Brake Fluid
Brake Fluid
319
12/07/13 17:17:25 31TM8630_324
Maintenance
TOC
2013 Insight
The fluid level should be betweenthe MIN and MAX marks on the sideof the reservoir. If the level is at orbelow the MIN mark, your brakesystem needs attention. Have thebrake system inspected for leaks orworn brake pads.
Always use Honda Heavy DutyBrake Fluid DOT 3. If it is notavailable, you should use only DOT 3or DOT 4 fluid, from a sealedcontainer, as a temporaryreplacement.
Using any non-Honda brake fluid cancause corrosion and decrease the lifeof the system. Have the brakesystem flushed and refilled withHonda Heavy Duty Brake FluidDOT 3 as soon as possible.
Brake fluid marked DOT 5 is notcompatible with your vehicle’sbraking system and can causeextensive damage.
Brake Fluid
320
MAX
MIN
12/07/13 17:17:30 31TM8630_325
Maintenance
TOC
2013 Insight
CONTINUED
Open the hood.
Your vehicle has halogen headlightbulbs. When replacing a bulb,handle it by its base, and protect theglass from contact with your skin orhard objects. If you touch the glass,clean it with denatured alcohol and aclean cloth.
The headlights were properly aimedwhen your vehicle was new. If youregularly carry heavy items in thecargo area, readjustment may berequired. Adjustments should bedone by your dealer or anotherqualified technician.
To change the bulb on the rightside, remove the upper part of thewindshield washer reservoir tank.Use a flat-tip screwdriver toremove the holding clip, thenremove the upper part by pulling itstraight up.
Remove the electrical connectorfrom the cover by pushing on thetab to unlock it, then slide theconnector off the cover.
Remove the cover on the back ofthe headlight assembly by turningit counterclockwise.
1.2.
3.
Headlight Aiming
Replacing a Headlight Bulb
Lights
High Beam Headlight
321
HOLDING CLIP
CONNECTOR
Halogen headlight bulbs get very hotwhen lit. Oil, perspiration, or a scratchon the glass can cause the bulb tooverheat and shatter.
12/07/13 17:17:39 31TM8630_326
Maintenance
TOC
2013 Insight
Remove the electrical connectorfrom the bulb by pushing on
Remove the bulb from theheadlight assembly by turning itone-quarter turn counterclockwise.
Install the new bulb, and turn itone-quarter turn clockwise to lockit in place.
Push the electrical connector backonto the bulb. Make sure it is onall the way.
Reinstall the cover over the backof the headlight assembly and turnit clockwise to lock it in place.Push the electrical connector backonto the cover.
Turn on the headlights to test thenew bulb.
4. 5.
6.
7.
8.
9.
Lights
322
BULB
COVER
CONNECTOR
12/07/13 17:17:46 31TM8630_327
Maintenance
TOC
the tab and pulling theconnector down.
Install the upper part of thewindshield washer reservoir tankin the reverse order of removal.
(Right side)10.
2013 Insight
Install the new bulb, and turn itone-quarter turn clockwise to lockit in place.
Push the electrical connector backonto the bulb. Make sure it is onall the way.
Turn on the headlights to test thenew bulb.
Remove the bulb from theheadlight assembly by turning itone-quarter turn counterclockwise.
Remove the electrical connectorfrom the bulb by pushing on thetab and pulling the connectordown.
Open the hood.
3.
4.
5.
6.
2.
1.
Lights
Low Beam Headlight
323
BULB
CONNECTOR
12/07/13 17:17:54 31TM8630_328
Maintenance
TOC
2013 Insight
Open the hood.To change the bulb on the rightside, remove the upper part of thewindshield washer reservoir tank.Use a flat-tip screwdriver toremove the holding clip, thenremove the upper part by pulling itstraight up.
Remove the socket from theheadlight assembly by turning itone-quarter turn counterclockwise.
Pull the bulb straight out of itssocket. Push the new bulb straightinto the socket until it bottoms.
Install the socket back into theheadlight assembly. Turn itclockwise to lock it in place.
Turn on the lights to make surethe new bulb is working.
Install the upper part of thewindshield washer reservoir tankin the reverse order of removal.
(Right side)6.
1.
2.
3.
4.
5.
Lights
Replacing a FrontParking Light Bulb
324
BULB
HOLDING CLIP
SOCKET
12/07/13 17:18:03 31TM8630_329
Maintenance
TOC
2013 Insight
Remove the socket from the frontturn signal light assembly byturning it one-quarter turncounterclockwise.
Pull the bulb straight out of itssocket. Push the new bulb straightinto the socket until it bottoms.
Insert the socket back into thefront turn signal light assembly.Turn it clockwise to lock it in place.
Turn on the lights to make surethe new bulb is working.
Install the garnish in the originalposition securely.
Place a cloth on the notch of thelight assembly garnish to preventscratches. Remove the cover bycarefully prying in the notch with aflat-tip screwdriver.
Remove the bolts and pull thefront turn signal light assemblyfrom the bumper while taking thetab out from the holder.
Install the light assembly in thereverse order of removal. Makesure to secure the bolts.
5.
6.
1.
7.
8.
3.
4.
2.
Lights
Replacing the FrontTurn Signal Light Bulb
325
NOTCH
COVER BOLTS
BULBSOCKET
12/07/13 17:18:12 31TM8630_330
Maintenance
TOC
2013 Insight
Open the hood.
Remove the socket from theheadlight assembly by turning itone-quarter turn counterclockwise.
Pull the bulb straight out of itssocket. Push the new bulb straightinto the socket until it bottoms.
Install the socket back into theheadlight assembly. Turn itclockwise to lock it in place.
Turn on the lights to make surethe new bulb is working.
2.
3.
4.
5.
1.
Lights
Replacing a FrontSide Marker Light Bulb
326
BULB
SOCKET
12/07/13 17:18:19 31TM8630_331
Maintenance
TOC
2013 Insight
CONTINUED
Open the hatch.
Push on the area of the trim asshown in the illustration above todetach the upper hooks from thelight assembly.
Pry on the gap between the trimand light assembly carefully with aflat-tip screwdriver to detach thelower hooks.
Make sure that all hooks areremoved from the light assembly.Unclip the top half of the trimfrom the body by pulling it out.Then unclip the bottom half.
1.
2.
3. 4.
Lights
Replacing the Rear Bulbs
327
HOOKS
TRIMHOOKS
CLIP
CLIP
12/07/13 17:18:27 31TM8630_332
Maintenance
TOC
2013 Insight
Remove the two mounting boltswith an 8 mm wrench.
Pull the rear of the light assemblyout as shown in the illustrationabove ( ), then push theassembly back to the originalposition carefully ( ). The frontpart of the rear light assemblyraises slightly ( ).
Determine which of the threebulbs is burned out: back-up light,turn signal, or side marker.
Pull the whole light assemblyoutwards from the body carefully.
Remove the socket by turning itone-quarter turn counterclockwise.
Remove the burned out bulb bypulling it straight out of its socket.
6.
7.
5. 8.
9.
10.
Lights
328
BOLT
ORIGINALPOSITION
Front
Front
Left side
BULB
SOCKETSNAP FASTENERS
Left side
12/07/13 17:18:36 31TM8630_333
Maintenance
TOC
2013 Insight
Install the new bulb in the socketby pushing it straight in the socketuntil it bottoms.
Reinstall the socket into the lightassembly. Turn it clockwise tolock it in place.
Test the lights to make sure thenew bulb is working.
When reinstalling the taillightassembly, align and pop the snapfasteners in place. Reinstall andtighten the two mounting bolts.
To reinstall the trim, set thebottom edge of the trim in theoriginal position and push thebottom half of the trim to clip itback securely. Then push theupper half of the trim to securethe top clip.
Secure the hooks by pushing onthe areas of the trim as shown inthe illustration above.
11.
12.
13.
14.
15. 16.
Lights
329
12/07/13 17:18:43 31TM8630_334
Maintenance
TOC
2013 Insight
The high-mount brake light shouldbe replaced by your dealer.
The license plate has two lightsabove it. The bulbs should bereplaced by your dealer.
Each outside mirror has side turnsignal lights. The lights should bereplaced by your dealer.
The stop/taillights should bereplaced by your dealer.
EX models
Lights
High-mount Brake Light
Rear License Plate Light Bulbs
Side Turn Signal Lights
Stop/taillights
330
12/07/13 17:18:49 31TM8630_335
Maintenance
TOC
2013 Insight
Before using an automatic carwash, remove the audio antennaso it does not get damaged. Removethe antenna by unscrewing it.When you reinstall the antenna,tighten it securely.
Before entering or parking in areas with low ceiling height,remove the antenna.
The driver’s floor mat that camewith your vehicle hooks over thefloor mat anchors. To lock eachanchor, turn the knob clockwise.This keeps the floor mat from slidingforward and possibly interfering withthe pedals.
If your seat belts get dirty, use a softbrush with a mixture of mild soapand warm water to clean them. Donot use bleach, dye, or cleaningsolvents. Let the belts air dry beforeyou use the vehicle.Dirt build-up in the loops of the seatbelt anchors can cause the belts toretract slowly. Wipe the insides ofthe loops with a clean clothdampened in mild soap and warmwater or isopropyl alcohol.
When cleaning or replacing, turn theknob counterclockwise to unhookthe floor mat. CONTINUED
On LX and EX models
Floor MatsCleaning the Seat BeltsAudio Antenna
Audio Antenna, Cleaning the Seat Belts, Floor Mats
331
LOOP
To unlock
Driver’s floor mat is shown.
12/07/13 17:18:59 31TM8630_336
Maintenance
TOC
2013 Insight
Check the condition of the wiperblades at least every 6 months.Replace them if you find signs ofcracking in the rubber, and areasthat are getting hard or if theyleave streaks and unwiped areas when used.
If you remove a floor mat, make sureto re-anchor it when you put it backin your vehicle.
If you use a non-Honda floor mat,make sure it fits properly and that itcan be used with the floor matanchors. Do not put additional floormats on top of the anchored mats.
Make sure the rear floormats are properly positioned. Ifnot, the floor mat will interferewith the seat operation and makethe front passenger’s weightsensors ineffective.
This filter removes the dust andpollen that is brought in from theoutside through the climatecontrol system.
Have your dealer replace the filterwhen this service is indicated by amaintenance message on the multi-information display. It should bereplaced every 15,000 miles (24,000km) if you drive primarily in urbanareas that have high concentrationsof soot in the air, or if the flow fromthe climate control system becomesless than usual.
Wiper BladesDust and Pollen Filter
Floor Mats, Dust and Pollen Filter, Wiper Blades
332
12/07/13 17:19:05 31TM8630_337
Maintenance
TOC
2013 Insight
To replace a wiper blade:
Raise each wiper arm off thewindshield, lifting the driver’s sidefirst, then the passenger’s side.
Disconnect the blade assemblyfrom the wiper arm:
When replacing a wiper blade,make sure not to drop the wiperblade or wiper arm down on thewindshield.
Put a cloth on the edge of thelock tab to prevent scratches,then push up on the lock tabcarefully with a flat-tipscrewdriver.
Pivot the blade assembly towardthe wiper arm until it releasesfrom the wiper arm.1.
2.
CONTINUED
Wiper Blades
333
WIPER ARMS
WIPER ARM
COVER
Do not open the hood when the wiperarms are raised, or you will damage thehood and wiper arms.
12/07/13 17:19:14 31TM8630_338
Maintenance
TOC
2013 Insight
Remove the blade from its holderby grabbing the tabbed end of theblade. Pull firmly until the tabscome out of the holder.
Make sure the two rubber tabsinside the blade fit to each notch ofthe reinforcement, as shown.
is completely installed.
Place the top of the wiper bladeon the end of the blade assembly,and slide the blade onto theassembly. Make sure the blade
Examine the new wiper blades. Ifthey have no plastic or metalreinforcement along the backedge, remove the metalreinforcement strips from the oldwiper blade, and install them inthe slots along the edge of thenew blade.
3.
4.
5.
Wiper Blades
334
BLADE
REINFORCEMENT
BLADE
12/07/13 17:19:21 31TM8630_339
Maintenance
TOC
2013 Insight
Slide the wiper blade assemblyonto the wiper arm. Make sure itlocks in place.
Make sure the blade is completelyinstalled and that its edge is notbunched up.
Lower the wiper arm down againstthe windshield, the passenger’sside first, then the driver’s side.
To replace a rear wiper blade:
Raise the wiper arm off therear window.
Disconnect the blade assemblyfrom the wiper arm by pulling upthe cover.
6.
7.
8.
1.
2.
CONTINUED
Wiper Blades
335
COVER
REAR
12/07/13 17:19:29 31TM8630_340
Maintenance
TOC
2013 Insight
Examine the new wiper blades. Ifthey have no plastic or metalreinforcement along the backedge, remove the metalreinforcement strips from the oldwiper blade, and install them inthe slots along the edge of thenew blade.
Make sure the two rubber tabsinside the blade fit to each notch ofthe reinforcement, as shown.
Remove the blade from its holderby grabbing the tabbed end of theblade. Pull firmly until the tabscome out of the holder.
Push the blade assembly towardthe base of the arm.
When replacing a wiper blade,make sure not to drop thewiper blade or wiper arm down on the windshield.
3. 4.
5.
Wiper Blades
336
BLADE
REINFORCEMENT
WIPER ARM
BLADETOP
12/07/13 17:19:36 31TM8630_341
Maintenance
TOC
2013 Insight
CONTINUED
Slide the wiper blade assemblyonto the wiper arm. Make sure itlocks in place.
Make sure the blade is completelyinstalled and that its edge is notbunched up.
Place the top of the wiper bladeon the end of the blade assembly,and slide the blade onto theassembly. Make sure the bladeis completely installed.
Lower the wiper arm down againstthe windshield.
7.
8.
6.
9.
Wiper Blades
337
12/07/13 17:19:42 31TM8630_342
Maintenance
TOC
2013 Insight
To safely operate your vehicle, yourtires must be the proper type andsize, in good condition with adequatetread, and correctly inflated.
The following pages give moredetailed information on how to takecare of your tires and what to dowhen they need to be replaced.
Keeping the tires properlyinflated provides the bestcombination of handling,tread life, and riding comfort.
Underinflated tires wear unevenly,adversely affect handling and fueleconomy, and are more likely tofail from being overheated.Overinflated tires can make yourvehicle ride more harshly, aremore prone to damage from roadhazards, and wear unevenly.
The tire pressure monitoring system(TPMS) warns you when a tirepressure is low. See page formore information.
Even though your vehicle isequipped with TPMS, werecommend that you visually checkyour tires every day. If you think atire might be low, check itimmediately with a tire gauge.
Use a gauge to measure the airpressure in each tire at least once amonth. Even tires that are in goodcondition may lose 1 to 2 psi (10 to20 kPa, 0.1 to 0.2 kgf/cm ) permonth. Remember to check thespare tire at the same time.
Check the air pressures when thetires are cold. This means thevehicle has been parked for at least3 hours, or driven less than 1 mile(1.6 km). Add or release air, ifneeded, to match the recommended cold tire pressures.We recommend that you visually
check your tires every day. If youthink a tire might be low, check itimmediately with a tire gauge.
289
On U.S. models
On U.S. models
On all Canadian models
Tires Inflation Guidelines
Tires
338
Using tires that are excessivelyworn or improperly inflated cancause a crash in which you canbe seriously hurt or killed.
Follow all instructions in thisowner’s manual regarding tireinflation and maintenance.
12/07/13 17:19:53 31TM8630_343
Maintenance
TOC
2013 Insight
If you check air pressures when thetires are hot (driven for severalmiles/kilometers), you will seereadings 4 to 6 psi (30 to 40 kPa, 0.3to 0.4 kgf/cm ) higher than the coldreadings. This is normal. Do not letair out to match the recommendedcold air pressure. The tire will
You should get your own tirepressure gauge and use it wheneveryou check your tire pressures. Thiswill make it easier for you to tell if apressure loss is due to a tireproblem and not due to a variation between gauges.
While tubeless tires have someability to self-seal if they arepunctured, you should lookclosely for punctures if a tirestarts losing pressure.
The following chart shows therecommended cold tire pressures formost normal driving conditions.
The compact spare tire pressure is:
Every time you check inflation, youshould also examine the tires fordamage, foreign objects, and wear.
You should look for:
Bumps or bulges in the tread orside of the tire. Replace the tire ifyou find either of these conditions.
Cuts, splits, or cracks in the sideof the tire. Replace the tire if youcan see fabric or cord.
Excessive tread wear.
For convenience, the recommendedtire sizes and cold tire pressures areon a label on the driver’s doorjamb.
For additional information aboutyour tires, see page .382
Tire Size Cold Tire Pressure
Recommended Tire Pressures Tire Inspection
Tires
339
60 psi (420 kPa , 4.2 kgf/cm )
P185/60R15 84T33 psi (230 kPa ,2.3 kgf/cm )
Front/Rear:
12/07/13 17:20:05 31TM8630_344
Maintenance
TOC
be underinflated.
2013 Insight
Your tires have wear indicatorsmolded into the tread. When thetread wears down, you will see a 1/2inch (12.7 mm) wide band across thetread. This shows there is less than1/16 inch (1.6 mm) of tread left onthe tire.
A tire this worn gives very littletraction on wet roads. You shouldreplace the tire if you can see threeor more tread wear indicators.
The service life of your tires isdependent on many factors,including, but not limited to, drivinghabits, road conditions, vehicleloading, inflation pressure,maintenance history, speed, andenvironmental conditions (evenwhen the tires are not in use).In addition to your regularinspections and inflation pressuremaintenance, it is recommended thatyou have annual inspectionsperformed once the tires reach fiveyears old. It is also recommendedthat all tires, including the spare, beremoved from service after 10 yearsfrom the date of manufacture,regardless of their condition or stateof wear.
The last four digits of the TIN (tireidentification number) are found onthe sidewall of the tire and indicatethe date of manufacture (See
on page ).
In addition to proper inflation,correct wheel alignment helps todecrease tire wear. If you find a tireis worn unevenly, have your dealercheck the wheel alignment.
Have your dealer check the tires ifyou feel a consistent vibration whiledriving. A tire should always berebalanced if it is removed from thewheel. When you have new tiresinstalled, make sure they arebalanced. This increases ridingcomfort and tire life. For best results,have the installer perform a dynamicbalance.
383
Tire Service Life
TireLabeling
Tire Maintenance
Tires
340
TREAD WEAR INDICATOR
INDICATOR LOCATION MARKS
Improper wheel weights can damageyour vehicle’s aluminum wheels. Useonly Honda wheel weights f orbalancing.
12/07/13 17:20:13 31TM8630_345
Maintenance
TOC
2013 Insight
To help increase tire life anddistribute wear more evenly, rotatethe tires according to themaintenance messages displayed onthe multi-information display. Movethe tires to the positions shown inthe illustration each time they arerotated. If you purchase directionaltires, rotate only front-to-back.
Replace your tires with radial tires ofthe same size, load range, speedrating, and maximum cold tirepressure rating (as shown on thetire’s sidewall).
It is best to replace all four tires atthe same time. If that is not possibleor necessary, replace the two fronttires or two rear tires as a pair.Replacing just one tire can seriouslyaffect your vehicle’s handling.
If you ever replace a wheel, makesure that the wheel’s specificationsmatch those of the original wheels.
Replacement wheels are available atyour dealer.
Also be sure you use only TPMSspecific wheels. If you do not, thetire pressure monitoring system willnot work.
Mixing radial and bias-ply tires onyour vehicle can reduce brakingability, traction, and steeringaccuracy. Using tires of a differentsize or construction can cause theABS and vehicle stability assistsystem (VSA) to work inconsistently.
The ABS and VSA system work bycomparing the speed of each wheel.When replacing tires, use the samesize originally supplied with thevehicle. Tire size and constructioncan affect wheel speed and maycause the system to activate.
On U.S. models
CONTINUED
Tire Rotation Replacing Tires and Wheels
Tires
341
Front Front
(Front Non-directionalTires and Wheels)
(Front DirectionalTires and Wheels)
12/07/13 17:20:23 31TM8630_346
Maintenance
TOC
2013 Insight
+
Wheels:
Tires:
See page for DOT tire qualitygrading information, and page 384for tire size information.
Tires marked ‘‘M S’’ or ‘‘AllSeason’’ on the sidewall have an all-weather tread design suitable formost winter driving conditions.
For the best performance in snowyor icy conditions, you should installsnow tires or tire chains. They maybe required by local laws undercertain conditions.
If you mount snow tires on yourvehicle, make sure they are radialtires of the same size and load rangeas original tires. Mount snow tires onall four wheels. The tractionprovided by snow tires on dry roadsmay be lower than your original tires.Check with the tire dealer formaximum speed recommendations.
Because your vehicle has limited tireclearance, Honda stronglyrecommends using the chains listedbelow, made by Security ChainCompany (SCC).
Mount tire chains on your tires whenrequired by driving conditions orlocal laws. Install them only on thefront tires.
Cable-type: SCC RADIAL CHAINSC1026
382
Wheel and Tire Specifications
Winter Driving
Snow Tires
Tire Chains
Tires
342
15 x 6J
P185/60R15 84T
Installing improper tires on yourvehicle can affect handling andstability. This can cause a crashin which you can be seriouslyhurt or killed.
Always use the size and type oftires recommended in thisowner’s manual.
12/07/13 17:20:33 31TM8630_347
Maintenance
TOC
2013 Insight
When installing cables, follow themanufacturer’s instructions, andmount them as tight as you can.Make sure they are not contactingthe brake lines or suspension. Driveslowly with them installed. If youhear them coming into contact withthe body or chassis, stop andinvestigate. Remove them as soon asyou begin driving on cleared roads.
Clean the wheels as you would therest of the exterior. Wash them with the same solution, and rinsethem thoroughly.
Aluminum alloy wheels have aprotective clear-coat that keeps thealuminum from corroding andtarnishing. Cleaning the wheels withharsh chemicals (including somecommercial wheel cleaners) or a stiffbrush can damage the clear-coat. To clean the wheels, use a milddetergent and a soft brush or sponge.
If equipped
Wheels
Tires
343
Using the wrong chains, or notproperly installing chains, candamage the brake lines andcause a crash in which you canbe seriously injured or killed.
Follow all instructions in thisowner’s manual regarding theselection and use of tire chains.
Traction devices that are the wrongsize or improperly installed candamage your vehicle’s brake lines,suspension, body, and wheels. Stopdriving if they are hitting any part ofthe vehicle.
12/07/13 17:20:40 31TM8630_348
Maintenance
TOC
2013 Insight
-
Check the condition of the 12 voltbattery monthly by looking at thetest indicator window. The label onthe battery explains the testindicator’s colors.
If your vehicle’s 12 volt battery isdisconnected or goes dead, the IMAbattery level gauge reading will notbe correct the next time you turn theignition switch to the ON (II)position. It will show less than theactual level temporarily. It will showthe correct level after you drive forat least 30 minutes.
Check the terminals for corrosion (awhite or yellowish powder). Toremove it, cover the terminals with asolution of baking soda and water. Itwill bubble up and turn brown. Whenthis stops, wash it off with plainwater. Dry off the battery with acloth or paper towel. Coat theterminals with grease to help preventfurther corrosion.
Battery posts,terminals, and related accessoriescontain lead and lead compounds.
If you need to connect the battery toa charger, disconnect both cables toprevent damaging your vehicle’selectrical system. Always disconnectthe negative ( ) cable first, andreconnect it last.
If additional 12 volt batterymaintenance is needed, see yourdealer or a qualified technician.
WARNING:
Wash your hands after handling.
Checking the 12 Volt Battery
344
TEST INDICATOR WINDOW
The battery gives off explosivehydrogen gas during normaloperation.
A spark or flame can cause thebattery to explode with enoughforce to kill or seriously hurt you.
Wear protective clothing and aface shield, or have a skilledtechnician do the batterymaintenance.
12/07/13 17:20:46 31TM8630_349
Maintenance
TOC
2013 Insight
If your vehicle’s battery isdisconnected, or goes dead, the timesetting may be lost. To reset the time,see page .
If your vehicle’s battery isdisconnected or goes dead, the audiosystem may disable itself. The nexttime you turn on the radio, you willsee ‘‘ENTER CODE’’ in thefrequency display. Use the presetbuttons to enter the code (seepage ).
The navigation system will alsodisable itself. The next time you turnon the ignition switch, the systemwill require you to enter a PINbefore it can be used. Refer to thenavigation system manual.
220
219
On vehicles with navigation system
Checking the 12 Volt Battery
345
12/07/13 17:20:51 31TM8630_350
Maintenance
TOC
2013 Insight
Fill the fuel tank.
If you need to park your vehicle foran extended period (more than 1month), there are several things youshould do to prepare it for storage.Proper preparation helps preventdeterioration and makes it easier toget your vehicle back on the road. Ifpossible, store your vehicle indoors.
Wash and dry the exteriorcompletely.
Clean the interior. Make sure thecarpeting, floor mats, etc., arecompletely dry.
Leave the parking brake off. Putthe transmission in Park.
Block the rear wheels.
If the vehicle is to be stored for alonger period, it should besupported on jackstands so thetires are off the ground.
Leave one window openslightly (if the vehicleis being stored indoors).
Disconnect the 12 volt battery.
Support the front and rear wiperblade arms with a folded towel or rag so they do nottouch the windshield.
If possible, periodically run theengine until it reaches fulloperating temperature (thecooling fans cycle on and offtwice). Preferably, do this oncea month.
Reconnect the 12 volt battery anddrive your vehicle every month forabout 30 minutes. This will keepthe IMA battery charged and ingood condition.
Cover the vehicle with a‘‘breathable’’ cover, one madefrom a porous material such as
cotton. Non-porous materials, suchas plastic sheeting, trap moisture,which can damage the paint.
To minimize sticking, apply asilicone spray lubricant to all doorand hatch seals. Also, apply avehicle body wax to the paintedsurfaces that mate with the doorand hatch seals.
Vehicle Storage
346
If this vehicle is unused f or over onemonth, the service lif e of the 100VNickel-Metal Hydride battery will bereduced and the battery may bepermanently damaged.
12/07/13 17:21:01 31TM8630_351
Maintenance
TOC
2013 Insight
This section covers the morecommon problems that motoristsexperience with their vehicles. Itgives you information about how tosafely evaluate the problem and whatto do to correct it. If the problem hasstranded you on the side of the road,you may be able to get going again.If not, you will also find instructionson getting your vehicle towed.
......................Compact Spare Tire . 348....................Changing a Flat Tire . 349
.............If the Engine Won’t Start . 356................................Jump Starting . 358
..............If the Engine Overheats . 360.........Low Oil Pressure Indicator . 363
12 Volt Battery Charging System.....................................Indicator . 364
.......Malfunction Indicator Lamp . 365...............Brake System Indicator . 366
..............................................Fuses . 367..............................Fuse Locations . 372
......................Emergency Towing . 374..........If Your Vehicle Gets Stuck . 375
Taking Care of the Unexpected
347
12/07/13 17:21:05 31TM8630_352
2013 Insight
Check the air pressure of thecompact spare tire every time youcheck the other tires. It should beinflated to:
Replace the tire when you can seethe tread wear indicator bars. Thereplacement tire should be the samesize and design, mounted on thesame wheel. The spare tire is notdesigned to be mounted on a regularwheel, and the spare wheel is notdesigned for mounting a regular tire.
Use the compact spare tire as atemporary replacement only. Getyour regular tire repaired or replaced,and put it back on your vehicle assoon as you can.
Follow these precautions:
Never exceed 50 mph (80 km/h).
This tire gives a harsher ride andless traction on some roadsurfaces. Use greater cautionwhile driving.
Do not use your compact sparetire on another vehicle unless it isthe same make and model.
Do not mount snow chains on thecompact spare tire.
After the flat tire is replaced withthe spare tire, the low tirepressure/TPMS indicator stays onwhile driving. After several miles(kilometers) driving, this indicatorbegins to flash, then stays onagain. You will also see a ‘‘CHECKTPMS SYSTEM’’ message on themulti-information display. This isnormal; the system cannotmonitor the spare tire pressure.Manually check the spare tirepressure to be sure it is correct.
On U.S. models
Compact Spare Tire
348
INDICATOR LOCATION MARK
TREAD WEAR INDICATOR BAR60 psi (420 kPa , 4.2 kgf/cm )
12/07/13 17:21:13 31TM8630_353
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
CONTINUED
If you have a flat tire while driving,stop in a safe place to change it.Drive slowly along the shoulder untilyou get to an exit or an area to stopthat is far away from the traffic lanes.
Park the vehicle on firm, level, andnon-slippery ground. Put thetransmission in Park. Apply theparking brake.
Turn on the hazard warning lights,and turn the ignition switch to theLOCK (0) position. Have allpassengers get out of the vehiclewhile you change the tire.
Open the hatch.
Remove the cargo area floor bycarefully pulling the front edge ofthe floor straight up.
4.
3.
2.
1.
Changing a Flat Tire
349
HOLDER
FLOOR
TAB
The vehicle can easily roll offthe jack, seriously injuringanyone underneath.
Follow the directions forchanging a tire exactly, andnever get under the vehiclewhen it is supported only by thejack.
12/07/13 17:21:21 31TM8630_354
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
Loosen each wheel nut 1/2 turnwith the wheel nut wrench.
Take the box out of the spare tire.
Take the spare tire casing out ofthe cargo area.
Unscrew the wing bolt and takethe spare tire out of its well.
Remove the jack compartmentcover by pulling the knob.
Turn the jack’s end bracketcounterclockwise to loosen it, thenremove the jack.
6.
7.
10.5. 8.
9.
Changing a Flat Tire
350
WHEEL NUT WRENCH
BOX JACK KNOB
COVERSPARE TIRECASING SPARE TIRE
12/07/13 17:21:29 31TM8630_355
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
CONTINUED
Remove the wheel nuts, thenremove the flat tire. Handle thewheel nuts carefully; they may behot from driving. Place the flat tireon the ground with the outsidesurface facing up.
Use the extension and the wheelnut wrench as shown to raise thevehicle until the flat tire is offthe ground.
Place the jack under the jackingpoint nearest the tire you need tochange. Turn the end bracketclockwise until the top of the jackcontacts the jacking point. Makesure the jacking point tab isresting in the jack notch.
Remove the wheel cover bycarefully prying under its edgewith the flat tip of the extension.
11. 13.
14.
12.Insight and LX models
Changing a Flat Tire
351
WHEEL NUT WRENCH EXTENSION
JACKING POINTS EXTENSION WHEEL NUT
WHEEL COVER
12/07/13 17:21:37 31TM8630_356
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
Before mounting the spare tire,wipe any dirt off the mountingsurface of the wheel and hub with a clean cloth. Wipe the hub carefully; it may be hot from driving.
Lower the vehicle to the ground,and remove the jack.
Put on the spare tire. Put thewheel nuts back on finger-tight,then tighten them in a crisscrosspattern with the wheel nut wrenchuntil the wheel is firmly againstthe hub. Do not try to tighten thewheel nuts fully.
Tighten the wheel nuts securely inthe same crisscross pattern.Have the wheel nut torquechecked at the nearestautomotive service facility.Tighten the wheel nuts to:
18.
17.
16.
15.
Changing a Flat Tire
352
BRAKE HUB
80 lbf·ft (108 N·m , 11 kgf·m)
12/07/13 17:21:43 31TM8630_357
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
CONTINUED
Place the flat tire face down in thespare tire well.
Remove the spacer cone from thewing bolt, turn it over, and put itback on the bolt.
Remove the carpet from theSecure the flat tire by screwingthe wing bolt back into its hole.Store the box in the wheel of theflat tire.
Remove the center cap (ifequipped) before storing the flattire in the cargo area well.
Install the spare tire casing in
20.
21.
19.
22.
23.
24.
EX models
Changing a Flat Tire
353
SPACER CONE
WING BOLTFor normal tire
For compactspare tire
CARPET
SPARE TIRECASINGCENTER CAP
BOX
12/07/13 17:21:52 31TM8630_358
Taking
Care
ofthe
Unexpected
TOC
spare tire casing and store it inthe casing.
tire well.the original position in the spare
2013 Insight
Your vehicle’s original tire has atire pressure monitoring systemsensor. To replace a tire, refer to
(seepage ).
Store the center cap in the cargoarea. Make sure it does not getscratched or damaged.
Store the tools in the spare tirecasing and the jack in its holder.Turn the jack’s end bracketclockwise to lock it in place, andreinstall the cover.
Place the cargo area floor in itsoriginal position. Close the hatch.
25.
26.
27.
28.
291
U.S. models only
Changing a Flat Tire
Changing a Tire with TPMS
354
FLOOR
Loose items can fly around theinterior in a crash and couldseriously injure the occupants.
Store the wheel, jack, and toolssecurely before driving.
12/07/13 17:21:58 31TM8630_359
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
Make sure the wire support ring ishooked into the clips around theedge of the wheel cover.
Align the valve mark on the wheelcover to the tire valve on thewheel, then install the wheel cover.
Make sure the wire support ring ison the outer side of the tire valveas shown.1.
2. 3.Insight and LX models
Changing a Flat Tire
Installing a wheel cover
355
CLIPS CLIPS
WIRE SUPPORT RING
12/07/13 17:22:05 31TM8630_360
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
The engine normally starts with theIMA motor. If the engine does notstart while the IMA battery charge isnormally sufficient, check thefollowing:
Check the transmission interlock.The transmission must be in Parkor neutral or the starter will notoperate.
Are you using a properly codedkey? An improperly coded key willcause the immobilizer systemindicator in the instrument panelto blink rapidly (see page ).
Do you have fuel? Check the fuelgauge; the low fuel indicator maynot be working.
There may be an electricalproblem, such as no power to thefuel pump. Check all the fuses(see page ).
Are you using the proper startingprocedure? Refer to
on page .
130
263367
If the Engine Won’t Start
Starting theEngine
356
12/07/13 17:22:11 31TM8630_361
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
When the IMA battery charge is low,the starter motor is used to start theengine. If the engine does not start,check the following:
If the headlights dim noticeably orgo out when you try to start theengine, either the 12 volt battery isdischarged or the connections arecorroded. Check the condition ofthe 12 volt battery and terminalconnections (see page ). Youcan then try jump starting thevehicle from a booster 12 voltbattery (see page ).
If you find nothing wrong, you willneed a qualified technician to findthe problem. See
on page .
Turn the ignition switch to the ON(II) position. Turn on theheadlights, and check theirbrightness. If the headlights arevery dim or do not come on at all,the battery is discharged. See
on page .
Turn the ignition switch to theSTART (III) position. If theheadlights do not dim, check thecondition of the fuses. If the fusesare OK, there is probablysomething wrong with theelectrical circuit for the ignitionswitch or starter motor. You willneed a qualified technician todetermine the problem. See
on page .
358
374
344
358
374
If the Engine Won’t Start
EmergencyTowing
Jump Starting
Emergency Towing
357
12/07/13 17:22:16 31TM8630_362
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
Although this seems like a simpleprocedure, you should take severalprecautions.
To jump start your vehicle:
The numbers in the illustration show you the order to connect thejumper cables.
You cannot start your vehicle bypushing or pulling it.
Open the hood, and check thephysical condition of the 12 voltbattery.
Turn off all the electricalaccessories: climate control, audiosystem, lights, etc. Put thetransmission in Park, and set theparking brake.
1.
2.
Jump Starting
358
BOOSTERBATTERY
A battery can explode if you donot follow the correct procedure,seriously injuring anyonenearby.
Keep all sparks, open flames,and smoking materials awayfrom the battery.
If a battery sits in extreme cold, theelectrolyte inside can f reeze.Attempting to jump start with a f rozenbattery can cause it to rupture.
12/07/13 17:22:23 31TM8630_363
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
-+
+
Start the vehicle. If the startermotor still operates slowly, checkthat the jumper cables have goodmetal-to-metal contact.
Once your vehicle is running,disconnect the negative cable fromyour vehicle, then from thebooster battery. Disconnect thepositive cable from your vehicle,then from the booster battery.
Keep the ends of the jumper cablesaway from each other and any metalon the vehicle until everything isdisconnected. Otherwise, you maycause an electrical short.
If the booster battery is in anothervehicle, have an assistant startthat vehicle and run it at a fast idle.
Connect the second jumper cableto the negative ( ) terminal onthe booster battery. Connect theother end to the grounding strapas shown. Do not connect thisjumper cable to any other part ofthe engine.
Connect one jumper cable to thepositive ( ) terminal on yourbattery. Connect the other end tothe positive ( ) terminal on thebooster battery.
7.
6.
4.
5.
3.
CONTINUED
Jump Starting
359
12/07/13 17:22:31 31TM8630_364
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
If your vehicle’s 12 volt battery isdisconnected or goes dead, the IMAbattery level gauge reading will notbe correct the next time you turn theignition switch to the ON (II)position. It will show less than theactual level temporarily. It will showthe correct level after you drive forat least 30 minutes.
The high temperature indicatorshould be off under most conditions.If the engine coolant temperaturegets higher than normal, theindicator will blink. If it stays on, youshould determine the reason (hotday, driving up a steep hill, etc.).
You will also see a ‘‘WATER TEMPHOT’’ message on the multi-information display (see page ).
If the vehicle overheats, you shouldtake immediate action. The onlyindication may be the hightemperature indicator blinking orremaining on. Or you may see steamor spray coming from under thehood.
67
If the Engine Overheats
Jump Starting, If the Engine Overheats
360
Driving with the high temperatureindicator on can cause serious damageto your engine.
12/07/13 17:22:36 31TM8630_365
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
CONTINUED
Safely pull to the side of the road.Put the transmission in Park, andset the parking brake. Turn off allthe accessories, and turn on thehazard warning lights.
If you see steam and/or spraycoming from under the hood, turnoff the engine. Wait until you seeno more signs of steam or spray,then open the hood.
If you do not see steam or spray,leave the engine running, andcheck the high temperatureindicator. If the high heat is due tooverloading, the engine shouldstart to cool down almostimmediately. If it does, wait untilthe high temperature indicatorgoes off, then continue driving.
If the high temperature indicatorstays on, turn off the engine.
Look for any obvious coolant leaks,such as a split radiator hose.Everything is still extremely hot,so use caution. If you find a leak, itmust be repaired before youcontinue driving (see
on page ).
If you don’t find an obvious leak,check the coolant level in theradiator reserve tank (see page 250),Add coolant if the level is belowthe MIN mark.
If there was no coolant in thereserve tank, you may need to addcoolant to the radiator. Let theengine cool down until the hightemperature indicator goes offbefore checking the radiator.
1.
2.
3.
4.
5.
6.
7.
374
If the Engine Overheats
EmergencyTowing
361
Steam and spray from anoverheated engine canseriously scald you.
Do not open the hood if steamis coming out.
12/07/13 17:22:44 31TM8630_366
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
Using gloves or a large heavycloth, turn the radiator capcounterclockwise, withoutpushing down, to the first stop.After the pressure releases,push down on the cap, and turn ituntil it comes off.
If the temperature stays normal, check the coolantlevel in the radiator reservetank. If it has gone down,add coolant to the MAX mark.Put the cap back on tightly.
Start the engine, and set thetemperature to maximum heat(climate control to AUTO at‘‘ ’’). Add coolant to theradiator up to the base of the fillerneck. If you do not have theproper coolant mixture available,you can add plain water.Remember to have the coolingsystem drained and refilled withthe proper mixture as soon as
Put the radiator cap back ontightly. Run the engine, and checkthe high temperature indicator. Ifit begins to blink or comes onagain, the engine needs repair(see on
8.
9.
10.
11.
If the Engine Overheats
Emergency Towing
362
Removing the radiator capwhile the engine is hot cancause the coolant to spray out,seriously scalding you.
Always let the engine andradiator cool down beforeremoving the radiator cap.
12/07/13 17:22:50 31TM8630_367
Taking
Care
ofthe
Unexpected
TOC
page 374 ).
you can.
2013 Insight
If necessary, add oil to bring thelevel back to the full mark on thedipstick (see page ).
The engine running generates theoil pressure. When the Auto IdleStop is activated, the engineis stopped, the oil pressureis dropped, and the low oil pressureindicator does not come on.
Safely pull off the road, and shutoff the engine. Turn on the hazardwarning lights.
Let the vehicle sit for a minute.Open the hood, and check the oillevel (see page ). An enginevery low on oil can lose pressureduring cornering and other drivingmaneuvers.
Start the engine and watch the oilpressure indicator. If it does not goout within 10 seconds, turn off theengine. There is a mechanicalproblem that needs to be repairedbefore you can continue driving(see on
).
This indicator should nevercome on when the engine is
running. If it starts flashing or stayson, the oil pressure has dropped verylow or lost pressure. Serious enginedamage is possible, and you shouldtake immediate action.
You will also see a ‘‘CHECKENGINE OIL LEVEL’’ message onthe multi-information display whenthis indicator comes on.
The indicator notifies you of low oilpressure and does not measure theoil level. Check your vehicle’s oillevel at each refueling.
1.
2.
3.
4.
249
310
Low Oil Pressure Indicator
Emergency Towing
363
Running the engine with low oilpressure can cause serious mechanicaldamage almost immediately. Turn of fthe engine as soon as you can saf ely getthe vehicle stopped.
12/07/13 17:22:59 31TM8630_368
Taking
Care
ofthe
Unexpected
TOC
page 374
2013 Insight
- -
If the charging systemindicator comes on brightly
when the engine is running, the 12volt battery is not being charged.
Go to a service station orgarage where you can gettechnical assistance.
Immediately turn off all electricalaccessories. Try not to use otherelectrically operated controls such asthe power windows. Keep the enginerunning; starting the engine willdischarge the battery rapidly.
You will also see a ‘‘CHECKCHARGING SYSTEM’’ message onthe multi-information display (seepage ).
This indicator may blink after youstart the vehicle in the morningwhen the temperature is below
20°F ( 30°C). It will stopblinking when the IMA batterywarms up.
89
12 Volt Battery Charging System Indicator
364
12/07/13 17:23:04 31TM8630_369
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
If the indicator comes on repeatedly,even though it may turn off as youcontinue driving, have your vehiclechecked by your dealer as soon aspossible.
Your vehicle has certain ‘‘readinesscodes’’ that are part of the on-boarddiagnostics for the emissionssystems. In some states, part of theemissions testing is to make surethese codes are set. If they are notset, the test cannot be completed.
If the indicator comes onwhile driving, it means one
of the engine’s emissions controlsystems may have a problem. Eventhough you may feel no difference inyour vehicle’s performance, it canreduce your fuel economy and causeincreased emissions. Continuedoperation may cause serious damage.
If your vehicle’s battery has beendisconnected or gone dead, thesecodes are erased. It can take severaldays of driving under variousconditions to set the codes again.
To check if they are set, turn theignition switch to the ON (II)position, without starting the engine.The malfunction indicator lamp willcome on for 20 seconds. If it thengoes off, the readiness codes are set.If it blinks five times, the readinesscodes are not set. If possible, do nottake your vehicle for an emissionstest until the readiness codes are set.Refer to formore information (see page ).
If you have recently refueled yourvehicle, the indicator coming oncould be due to a loose or missingfuel fill cap. You will also see a‘‘TIGHTEN FUEL CAP’’ message onthe multi-information display.Tighten the cap until it clicks at leastonce (see page ). Tightening thecap will not turn the indicator offimmediately; it can take several daysof normal driving.
You will also see a ‘‘CHECKEMISSION SYSTEM’’ message onthe multi-information display. Formore information, see page .89
247 390
Malfunction Indicator Lamp
Readiness Code Emissions Testing
365
If you keep driving with theMalf unction Indicator Lamp on, youcan damage your vehicle’s emissionscontrols and engine. Those repairs maynot be covered by your vehicle’swarranties. This indicator may alsocome on with the ‘‘D’’ indicator.
12/07/13 17:23:12 31TM8630_370
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
However, if the brake pedal does not feel normal, you should takeimmediate action. A problem in onepart of the system’s dual circuitdesign will still give you braking attwo wheels. You will feel the brakepedal go down much farther beforethe vehicle begins to slow down,and you will have to press harderon the pedal.
Slow down and pull to the side of theroad when it is safe. Because of thelong distance needed to stop, it ishazardous to drive the vehicle. Youshould have it towed and repaired assoon as possible (see
on page ).
If this indicator comes on for anyother reason, have your vehicleinspected by your dealer. Theremay be a malfunction with theelectric brake distribution (EBD)system. Avoid hard braking and high speed driving.
If the fluid level is low, take yourvehicle to a dealer, and have thebrake system inspected for leaks orworn brake pads.
If the brake system indicator comeson while driving, the brake fluid levelis probably low. Press lightly on thebrake pedal to see if it feels normal.If it does, check the brake fluid levelthe next time you stop at a servicestation (see page ).
The brake system indicator normallycomes on when you turn the ignitionswitch to the ON (II) position and asa reminder to check the parkingbrake. If you do not release theparking brake, the indicator will stayon, and you will see a ‘‘RELEASEPARKING BRAKE’’ message on themulti-information display.
You will also see a ‘‘BRAKE FLUIDLOW’’ or ‘‘CHECK BRAKESYSTEM’’ message on the multi-information display (see page ).
If you must drive the vehicle a shortdistance in this condition, driveslowly and carefully.
If the ABS indicator comes on withthe brake system indicator, haveyour vehicle inspected by yourdealer immediately.
89
319
374
Brake System Indicator
EmergencyTowing
(Red)
366
12/07/13 17:23:19 31TM8630_371
U.S. Canada
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
The vehicle’s fuses are contained inthree fuse boxes.
The interior fuse box is behind thedashboard on the driver’s side.
The interior fuse box label isattached on the back side of thecover. To see the interior fuse boxlabel, remove the cover by pulling ittoward you while holding the bottomcenter part of cover.
CONTINUED
Fuses
367
INTERIOR
COVER
LABEL
FUSE BOX
12/07/13 17:23:26 31TM8630_372
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
The under-hood fuse box is locatednext to the battery. To open it, pushthe tab as shown.
The under-hood fuse is on thepositive terminal of the battery. Toopen it, push the tabs as shown.
Fuses
368
TABUNDER-HOOD
TAB(On the battery)
Next to the battery
12/07/13 17:23:30 31TM8630_373
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
If something electrical in yourvehicle stops working, the first thingyou should check for is a blown fuse.Determine from the chart on pages
and , or the diagram on thefuse box lid, which fuse or fusescontrol that device. Check thosefuses first, but check all the fusesbefore deciding that a blown fuse isthe cause. Replace any blown fuses,and check if the device works.
Turn the ignition switch to theLOCK (0) position. Make sure theheadlights and all otheraccessories are off.
Remove the cover from the under-hood fuse box located on thebattery (see page ).
Check each of the large fuses inthe under-hood fuse box on the 12volt battery by looking throughthe top at the wire inside.Replacement of these fuses shouldbe done by your dealer.
Check the smaller fuses in theunder-hood fuse boxes and all thefuses in the interior fuse box bypulling out each one with the fusepuller provided in the interiorfuse box.
1. 2. 4.
3.
372 373
368
CONTINUED
Checking and Replacing Fuses
Fuses
369
BLOWN
FUSE PULLER
12/07/13 17:23:39 31TM8630_374
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
Look for a blown wire inside thefuse. If it is blown, replace the fusewith one of the spare fuses of thesame rating or lower.
The fuse puller is in the interiorfuse box.
If you cannot drive the vehiclewithout fixing the problem, and youdo not have a spare fuse, take a fuseof the same rating or a lower ratingfrom one of the other circuits. Makesure you can do without that circuittemporarily (such as the accessorypower socket or radio).
If you replace the blown fuse with aspare fuse that has a lower rating, itmight blow out again. This does notindicate that anything is wrong.Replace the fuse with one of thecorrect rating as soon as you can.
5.
Fuses
370
BLOWNFUSE PULLER
12/07/13 17:23:44 31TM8630_375
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
If the replacement fuse of thesame rating blows in a short time,there is probably a seriouselectrical problem with yourvehicle. Leave the blown fuse inthat circuit, and have your vehiclechecked by a qualified technician.
When the audio system is disabled,the clock setting in the audio systemis canceled. You need to reset theclock according to the instructions inthe audio system section in thisowner’s manual.
6.
Fuses
371
Replacing a f use with one that has ahigher rating greatly increases thechances of damaging the electricalsystem. If you do not have areplacement f use with the proper ratingf or the circuit, install one with a lowerrating.
12/07/13 17:23:48 31TM8630_376
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
-
--
-
-
*
*
No. No. Amps.Amps. Circuits ProtectedCircuits Protected1234567891011121314151617
18
19
202122
23242526272829303132333435363738394041424344
10 A10 A
10 A30 A20 A10 A30 A7.5 A10 A20 A10 A15 A15 A30 A15 A15 A
10 A7.5 A7.5 A
15 A(7.5 A)
20 A
10 A10 A10 A7.5 A
7.5 A7.5 A10 A20 A7.5 A7.5 A10 A20 A
20 A
20 A
15 A15 A7.5 A
HazardStop/HornNot UsedLAFDoor Lock MainHeadlight MainSmall LightRadiator Fan MotorIGPSRight Headlight Low BeamIG CoilLeft Headlight Low BeamDoor Lock Motor 2 (Lock)Door Lock Motor 1 (Lock)ABS/VSA FSRSelectable Door LockIGPNot UsedNot UsedIMA 1MG ClutchSTS
Back UpTPMSDriver’s Power WindowNot UsedBack Up LightSRSTransmission SOLOPDSNot UsedA/CABS/VSAIMAACC SocketAccessoryDaytime Running LightRear WiperFront Passenger’s PowerWindowRear Passenger’s SidePower WindowRear Driver’s Side PowerWindowFuel PumpWasherMeter
: U.S. models
Fuse Locations
372
INTERIOR FUSE BOX
12/07/13 17:23:54 31TM8630_377
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
-
-
-
***
* *
*
* *
No. Circuits Protected
No.
Amps.
Amps.
No. Amps. Circuits Protected
Circuits Protected
12
Ignition Coil (EX)Ignition Coil (IN)
454647484950515253545556575859
6015 A15 A
7.5 A
30 A10 A15 A15 A10 A15 A10 A
10 A30 A30 A30 A30 A40 A
50 A
123
100 A60 A20 A
Battery, Main, ACGEPSHorn, Stop, Hazard
Hatch LockNot UsedCondenser Fan MotorLeft Headlight High BeamDoor Lock Motor 2 (Unlock)Door Lock Motor 1 (Unlock)Right Headlight High BeamDBWIMA 2Not UsedHeated MirrorFront WiperBlower MotorABS/VSA MotorRear DefoggerRear DefoggerNot UsedIG Main
1 :2 :3 :
Insight model and U.S. LX modelCanadian modelsEX models
2, 3
1
2, 3
Fuse Locations
373
UNDER-HOOD FUSE BOXES
On the battery Next to the battery
12/07/13 17:24:03 31TM8630_378
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
-
-
If, due to damage, your vehicle mustbe towed with the front wheels onthe ground, do this:
With the front wheels on the ground,it is best to tow the vehicle no fartherthan 50 miles (80 km), and keep thespeed below 35 mph (55 km/h).
If your vehicle needs to be towed,call a professional towing service ororganization. Never tow yourvehicle with just a rope or chain. Itis very dangerous.
There are two ways to tow yourvehicle:
The towtruck uses two pivoting arms that gounder the tires (front) and lift themoff the ground. The other two tiresremain on the ground.
The operatorloads your vehicle on the back of atruck.
Start the engine.Shift to the D position and hold for5 seconds, then to N.Turn off the engine.Release the parking brake.Leave the ignition switch in theACCESSORY (I) position so thesteering wheel does not lock.
Wheel-lif t Equipment
Flat-bed Equipment
This is anacceptable way to tow your vehicle.
This is the best way totransport your vehicle.
Emergency Towing
374
Improper towing preparation willdamage the transmission. Follow theabove procedure exactly. If you cannotshif t the transmission or start theengine, your vehicle must betransported with the f ront wheels of fthe ground.
12/07/13 17:24:12 31TM8630_379
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
To use the towing hook:
Remove the cover from the frontbumper using your fingers, or pryit off using a cloth and a flat-tipscrewdriver to prevent scratches.
If your vehicle gets stuck in sand,mud, or snow, call a towing serviceto pull it out (see page ).
For very short distances, such asfreeing the vehicle, you can use thedetachable towing hook that mountson the anchor in the front bumper.
Remove the towing hook andwheel nut wrench from the toolcase in the cargo area.
1.
2.
374
CONTINUED
If Your Vehicle Gets Stuck
Emergency Towing, If Your Vehicle Gets Stuck
375
Trying to lif t or tow your vehicle by thebumpers will cause serious damage.The bumpers are not designed tosupport the vehicle’s weight.
The steering system can be damaged ifthe steering wheel is locked. Leave theignition switch in the ACCESSORY (I)position, and make sure the steeringwheel turns f reely bef ore you begintowing.
12/07/13 17:24:20 31TM8630_380
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
Screw the towing hook into thehole, and tighten it with the wheelnut wrench.
3.
If Your Vehicle Gets Stuck
376
WHEEL NUT WRENCH
To avoid damage to your vehicle, usethe towing hook f or straight, f latground towing only. Do not tow at anangle. The tow hook should not be usedto tow the vehicle onto a f lat bed. Donot use it as a tie down.
12/07/13 17:24:24 31TM8630_381
Taking
Care
ofthe
Unexpected
TOC
2013 Insight
-
The diagrams in this section giveyou the dimensions and capacities ofyour vehicle and the locations of theidentification numbers. It alsoincludes information you shouldknow about your vehicle’s tires andemissions control systems.
................Identification Numbers . 378................................Specifications . 380
DOT Tire Quality Grading......................(U.S. Vehicles) . 382
Uniform Tire Quality..................................Grading . 382.................................Treadwear . 382
......................................Traction . 382.............................Temperature . 383
.................................Tire Labeling . 383Tire Pressure Monitoring System
(TPMS) Required Federal............................Explanation . 385
.......................Emissions Controls . 387.....................The Clean Air Act . 387
Crankcase Emissions Control....................................System . 387
Evaporative Emissions Control....................................System . 387
Onboard Refueling Vapor................................Recovery . 387
...Exhaust Emissions Controls . 388....................PGM-FI System . 388
Ignition Timing Control................................System . 388
Exhaust Gas Recirculation...................(EGR) System . 388
Three Way Catalytic...........................Converter . 388
....................Replacement Parts . 388..Three Way Catalytic Converter . 389
........................Emissions Testing . 390..Devices that Emit Radio Waves . 392
Technical Information
377
12/07/13 17:24:28 31TM8630_382
2013 Insight
Your vehicle has several identifyingnumbers in various places.
The vehicle identification number(VIN) is the 17-digit number yourdealer uses to register your vehiclefor warranty purposes. It is alsonecessary for licensing and insuringyour vehicle. The easiest place tofind the VIN is on a plate fastened tothe top of the dashboard. You cansee it by looking through thewindshield on the driver’s side. It isalso on the certification labelattached to the driver’s doorjamb,and is stamped on the enginecompartment bulkhead. The VIN isalso provided in bar code on thecertification label.
The VIN is also located on theengine bulkhead. Remove the coveron the engine compartmentbulkhead to view the VIN. Alwaysclose the cover when finished.
Identif ication Numbers
378
COVER
VEHICLE IDENTIFICATION NUMBER (VIN)
CERTIFICATION LABEL
12/07/13 17:24:33 31TM8630_383
TechnicalInform
ation
TOC
2013 Insight
The engine number is stamped intothe engine block.
The transmission number is on alabel on top of the transmission.
The IMA Motor Number is stampedon the motor housing.
Identif ication Numbers
379
ENGINE NUMBER
TRANSMISSION NUMBER
IMA MOTOR NUMBER
12/07/13 17:24:37 31TM8630_384
TechnicalInform
ation
TOC
2013 Insight
*
*
*
*
Specifications
380
Dimensions
Weights
Seating Capacities
Capacities
Engine
172.3 in (4,377 mm)66.7 in (1,695 mm)56.2 in (1,427 mm)100.4 in (2,550 mm)58.3 in (1,481 mm)58.0 in (1,472 mm)
LengthWidthHeightWheelbaseTrack
Gross vehicle weight rating See the certification label attachedto the driver’s doorjamb.
3.4 US qt (3.2 )3.2 US qt (3.0 )4.0 US qt (3.8 )
TotalFrontRear
523
Excluding the oil remaining in the engine
Including the coolant in the reserve tank and that remaining in theengineReserve tank capacity: 0.116 US gal (0.44 )
2.6 US qt (2.5 )4.76 US qt (4.50 )
Fuel tank
EnginecoolantEngine oil
Automatictransmissionfluid (CVTF)Windshieldwasherreservoir
Type
Bore x StrokeDisplacementCompression ratioSpark plugs
10.8 : 182 cu-in (1,339 cm )
2.87 x 3.15 in (73.0 x 80.0 mm)
3.0 US qt (2.8 )5.5 US qt (5.2 )
10.6 US gal (40 )1.165 US gal (4.41 )1.295 US gal (4.90 )
Water cooled 4-stroke SOHCi-VTEC gasoline engine with
Hybrid Electric Motor
DILFR6J11
FrontRear
Approx.
1 :
2 :
ChangeTotalChange
Including filterWithout filter
TotalChangeTotal
U.S. VehiclesCanada Vehicles
(NGK)
1
2
12/07/13 17:24:52 31TM8630_385
TechnicalInform
ation
TOC
2013 Insight
- -
±- ±
±± ±± ±
--
-----
-
------
-
***
*
* *
*
*
*
*
Specifications
381
Air Conditioning
Tires
Alignment
Fuses
12 Volt Battery
Lights
HFC-134a (R-134a)15.8 17.6 oz (450 500 g)
SP-10
12 V 60 W
Refrigerant typeCharge quantityLubricant oil type
12 V 55 W
Size
Pressure
Toe-in
Camber
Caster
Interior
Under-hood
60 psi (420 kPa , 4.2 kgf/cm )33 psi (230 kPa , 2.3 kgf/cm )
P185/60R15 84T
3°30’ 0.5°1.5° 1°0° 1°
Capacity 12 V12 V
35 AH/20 HR28 AH/5 HR
12 V 21 W
T135/80D15 99M
12 V 5 W
12 V 3.4 W
12 V12 V12 V12 V12 V12 V
5 W8 W8 W5 W2 CP16 W
12 V 21 W
Replacement of a light bulb should be done by your dealer.
5 W12 V
0.10 0.10 in (2.5 2.5 mm)0 0.12 in (0 3 mm)
Headlights
Front turn signal lightsFront parking lightsFront side marker lightsSide turn signal lights(door mirror)Rear turn signal lightsStop/taillightsBack-up lightsRear side marker lightsLicense plate lightsSpot lightsCeiling lightCargo area lightHigh-mount brake lightGlove box light
See page 372 or the fuse labelattached to the inside of the fusebox door under the steeringcolumn.See page 373 or the fuse boxcover.
FrontRearFrontRearFront
HighLow
Front/RearSpareFront/RearSpare
(HB3)(H11)(Amber)
LED type
LED type
LED type
(Amber)in
1 :2 :3 : LX model
EX models
1
1, 3
1
2
2
2
12/07/13 17:25:15 31TM8630_386
TechnicalInform
ation
TOC
2013 Insight
Quality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample:
All passenger car tires must conformto Federal Safety Requirements inaddition to these grades.
The traction grades, from highest tolowest, are AA, A, B, and C. Thosegrades represent the tire’s ability tostop on wet pavement as measuredunder controlled conditions onspecified government test surfacesof asphalt and concrete. A tiremarked C may have poor tractionperformance.
Warning: The traction gradeassigned to this tire is based onstraight-ahead braking traction tests,and does not include acceleration,cornering, hydroplaning, or peaktraction characteristics.
The tires on your vehicle meet allU.S. Federal Safety Requirements.All tires are also graded fortreadwear, traction, and temperatureperformance according toDepartment of Transportation(DOT) standards. The followingexplains these gradings.
The treadwear grade is a compara-tive rating based on the wear rate ofthe tire when tested under controlledconditions on a specified governmenttest course. For example, a tiregraded 150 would wear one and one-half (1 1/2) times as well on thegovernment course as a tire graded100. The relative performance oftires depends upon the actual condi-tions of their use, however, and maydepart significantly from the normdue to variations in driving habits,service practices and differences inroad characteristics and climate.
Uniform Tire Quality Grading
Treadwear 200Traction AATemperature A
Treadwear Traction
DOT Tire Quality Grading (U.S. Vehicles)
382
12/07/13 17:25:23 31TM8630_387
TechnicalInform
ation
TOC
2013 Insight
The temperature grades are A (thehighest), B, and C, representing thetire’s resistance to the generation ofheat and its ability to dissipate heatwhen tested under controlledconditions on a specified indoorlaboratory test wheel. Sustained hightemperature can cause the materialof the tire to degenerate and reducetire life, and excessive temperaturecan lead to sudden tire failure. Thegrade C corresponds to a level ofperformance which all passenger cartires must meet under the FederalMotor Vehicle Safety Standard No.109. Grades B and A representhigher levels of performance on thelaboratory test wheel than theminimum required by law.
The temperature grade
overloaded. Excessive speed,underinflation, or excessive loading,either separately or in combination,can cause heat buildup and possibletire failure.
The tires that came on your vehiclehave a number of markings. Thoseyou should be aware of are describedbelow.
CONTINUED
Temperature Tire Labeling
DOT Tire Quality Grading (U.S. Vehicles), Tire Labeling
383
(4) (3) (2)
(1)
(1)
(1)(2)(3)(4)
TIRE LABELING EXAMPLE
Tire Size
Maximum Tire PressureMaximum Tire Load
Tire Identification Number (TIN)
12/07/13 17:25:31 31TM8630_388
TechnicalInform
ation
TOC
Warning:
that is properly inflated and notfor this tire is established for a tire
2013 Insight
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Tire type code.
Date of manufacture.
Load index (a numerical codeassociated with the maximumload the tire can carry).
Speed symbol (analphabetical code indicatingthe maximum speed rating).
The tire identification number (TIN)is a group of numbers and lettersthat look like the following example.TIN is located on the sidewall of thetire.
This indicates that the tiremeets all requirements ofthe U.S. Department ofTransportation.
YearWeek
Manufacturer’sidentification mark.
Cold Tire Pressure The tire airpressure when the vehicle has beenparked for at least three hours ordriven less than 1 mile (1.6 km).
Load Rating Means the maximumload that a tire is rated to carry for agiven inflation pressure.
Maximum Inflation Pressure Themaximum tire air pressure that thetire can hold.
Whenever tires are replaced, theyshould be replaced with tires of thesame size. Following is an exampleof tire size with an explanation ofwhat each component means.
Rim diameter in inches.
Tire construction code (Rindicates radial).
Aspect ratio (the tire’s sectionheight as a percentage of itswidth).
Tire width in millimeters.
Vehicle type (P indicatespassenger vehicle).
RDOT
2202
15
84
EUYU
2KNR
T
60
185
P
Tire Labeling
Tire Size
Tire Identif ication Number (TIN)
Glossary of Tire Terminology
384
DOT EUYU 2KNR 2202
P185/60R15 84T
12/07/13 17:25:46 31TM8630_389
TechnicalInform
ation
TOC
2013 Insight
-
-
-
-
-As an added safetyfeature, your vehiclehas been equipped with a tire pressure monitoring system (TPM S) that illuminates alow tire pressure telltale when oneor more of your tires issignificantly under- inflated.
Accordingly, when the low tirepressure telltale illuminates, youshould stop and check your tires assoon as possible, and inflate them tothe proper pressure.
Maximum Load Rating Means theload rating for a tire at the maximumpermissible inflation pressure forthat tire.
Recommended Inflation PressureThe cold tire inflation pressurerecommended by the manufacturer.
Treadwear Indicators (TWI)Means the projections within theprincipal grooves designed to give avisual indication of the degrees ofwear of the tread.
Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pressure recommendedby the vehicle manufacturer on thevehicle placard or tire inflationpressure label.
(If your vehicle has tires of adifferent size than the size indicatedon the vehicle placard or tireinflation pressure label, you shoulddetermine the proper tire inflationpressure for those tires.)
CONTINUED
U.S. models only
Tire Labeling, Tire Pressure Monitoring System (TPMS) Required Federal Explanation
Tire Pressure Monitoring System(TPMS) Required FederalExplanation
385
12/07/13 17:25:55 31TM8630_390
TechnicalInform
ation
TOC
2013 Insight
-
Driving on a significantly under-inflated tire causes the tire tooverheat and can lead to tire failure.Under-inflation also reduces fuelefficiency and tire tread life, and mayaffect the vehicle’s handling andstopping ability.
Please note that the TPMS is not asubstitute for proper tiremaintenance, and it is the driver’sresponsibility to maintain correct tirepressure, even if under-inflation hasnot reached the level to triggerillumination of the TPMS low tirepressure telltale.
TPMS malfunctions may occur for avariety of reasons, including theinstallation of replacement oralternate tires or wheels on thevehicle that prevent the TPMS fromfunctioning properly.
Always check the TPMS malfunction telltale afterreplacing one or more tires orwheels on your vehicle to ensurethat the replacement or alternatetires and wheels allow the TPMS to continue to function properly.
Your vehicle has also been equippedwith a TPMS malfunction indicatorto indicate when the system is notoperating properly. The TPMSmalfunction indicator is combinedwith the low tire pressure telltale.When the system detects amalfunction, the telltale will flash forapproximately one minute and thenremain continuously illuminated.This sequence will continue uponsubsequent vehicle start-ups as longas the malfunction exists.
When the malfunction indicator isilluminated, the system may not beable to detect or signal low tirepressure as intended.
Tire Pressure Monitoring System (TPMS) Required Federal Explanation
386
12/07/13 17:26:00 31TM8630_391
TechnicalInform
ation
TOC
2013 Insight
*
*
The burning of gasoline in yourvehicle’s engine produces several by-products. Some of these are carbonmonoxide (CO), oxides of nitrogen(NOx), and hydrocarbons (HC).Gasoline evaporating from the tankalso produces hydrocarbons. Con-trolling the production of NOx, CO,and HC is important to the environ-ment. Under certain conditions ofsunlight and climate, NOx and HCreact to form photochemical ‘‘smog.’’Carbon monoxide does not
is a poisonous gas.
The United States Clean Air Actsets standards for automobileemissions. It also requires thatautomobile manufacturers explain toowners how their emissions controlswork and what to do to maintainthem. This section summarizes howthe emissions controls work.
In Canada, Honda vehicles comply withthe Canadian emission requirements, asspecified in an agreement withEnvironment Canada, at the time they
are manufactured.
Your vehicle has a positivecrankcase ventilation system. Thiskeeps gasses that build up in theengine’s crankcase from going intothe atmosphere. The positivecrankcase ventilation valve routesthem from the crankcase back to the
intake manifold. They are thendrawn into the engine and burned.
As gasoline evaporates in the fueltank, an evaporative emissionscontrol canister filled with charcoaladsorbs the vapor. It is stored in thiscanister while the engine is off. Afterthe engine is started and warmed up,the vapor is drawn into the engineand burned during driving.
The onboard refueling vaporrecovery (ORVR) system capturesthe fuel vapors during refueling. Thevapors are adsorbed in a canisterfilled with activated carbon. Whiledriving, the fuel vapors are drawninto the engine and burned off.
The Clean Air Act
Crankcase Emissions
Evaporative EmissionsControl System
Onboard RefuelingVapor Recovery
Emissions Controls
387
12/07/13 17:26:08 31TM8630_392
TechnicalInform
ation
TOC
Control System
contribute to smog creation, but it
2013 Insight
The exhaust emissions controlsinclude four systems: PGM-FI,ignition timing control, exhaust gasrecirculation, and three waycatalytic converter. These foursystems work together to control the engine’s combustion and minimize the amount of HC, CO,and NOx that come out the tailpipe.The exhaust emissions control systems are separate from thecrankcase and evaporativeemissions control systems.
The emissions control systems aredesigned and certified to work to-gether in reducing emissions tolevels that comply with the Clean AirAct. To make sure the emissionsremain low, you should use only newHonda replacement parts or theirequivalent for repairs. Using lowerquality parts may increase theemissions from your vehicle.
The emissions control systems arecovered by warranties separatefrom the rest of your vehicle.Read your warranty manual formore information.The PGM-FI system uses sequential
multiport fuel injection.It has three subsystems: air intake,engine control, and fuel control.The powertrain control module(PCM) uses various sensors to determine how much air is going into the engine. It then controls how much fuel to inject underall operating conditions.
This system constantly adjusts theignition timing, reducing the amountof HC, CO, and NOx produced.
The exhaust gas recirculation (EGR) system takes some of theexhaust gas and routes it backinto the intake manifold. Adding exhaust gas to the air/fuel mixturereduces the amount of NOxproduced when the fuel is burned.
The three way catalytic converter isin the exhaust system. Throughchemical reactions, it converts HC,CO, and NOx in the engine’s exhaustto carbon dioxide (CO ), nitrogen(N ), and water vapor.
2
2
Exhaust Emissions Controls Replacement Parts
PGM-FI System
Ignition Timing Control System
Exhaust Gas Recirculation (EGR) System
Three Way Catalytic Converter
Emissions Controls
388
12/07/13 17:26:17 31TM8630_393
TechnicalInform
ation
TOC
2013 Insight
The three way catalytic convertercontains precious metals that serveas catalysts, promoting chemicalreactions to convert the exhaustgasses without affecting the metals.The catalytic converter is referred toas a three-way catalyst, since it actson HC, CO, and NOx. A replacementunit must be an original Honda partor its equivalent.
The three way catalytic convertermust operate at a high temperaturefor the chemical reactions to takeplace. It can set on fire anycombustible materials that comenear it. Park your vehicle awayfrom high grass, dry leaves, orother flammables.
The defective three way catalyticconverters contribute to air pollution,and can impair your engine’sperformance. Follow theseguidelines to protect your vehicle’sthree way catalytic converters.
Always use unleaded gasoline.Even a small amount of leadedgasoline can contaminate thecatalyst metals, making the threeway catalytic converter ineffective.
Keep the engine well maintained.
Have your vehicle diagnosed andrepaired if it is misfiring, back-firing, stalling, or otherwise notrunning properly.
Three Way Catalytic Converter
389
U.S. model is shown.
THREE WAY CATALYTIC CONVERTERS
12/07/13 17:26:24 31TM8630_394
TechnicalInform
ation
TOC
2013 Insight
If you take your vehicle for anemissions test shortly after thebattery has been disconnected orgone dead, it may not pass the test.This is because of certain ‘‘readiness codes’’ that must be setin the on- board diagnostics for theemissions systems. These codes areerased when the batteryis disconnected, and set again onlyafter several days of driving under avariety of conditions.
Without touching the acceleratorpedal, start the engine, and let itidle for 20 seconds.
If the testing facility determines thatthe readiness codes are not set, youwill be requested to return at a laterdate to complete the test. If you mustget the vehicle retested within thenext two or three days, you cancondition the vehicle for retesting bydoing the following.
Make sure the gas tankis nearly, but not completely,full (around 3/4).
Make sure the vehicle has beenparked with the engine off for 6hours or more.
Make sure the ambienttemperature is between 40° and95°F (4° and 35°C).
Keep the vehicle in Park. Increasethe engine speed to 2,000 rpm, andhold it there for about 3 minutes.
Without touching the acceleratorpedal, let the engine idle for 20 seconds.
1.
2.
3.
4.
5.
6.
Testing of Readiness Codes
Emissions Testing
390
12/07/13 17:26:32 31TM8630_395
TechnicalInform
ation
TOC
2013 Insight
Select a nearby lightly traveledmajor highway where you canmaintain a speed of 50 to 60mph (80 to 97 km/h) for at least20 minutes. Drive on thehighway in D. Do not use thecruise control. When trafficallows, drive for 90 seconds without moving the acceleratorpedal. (Vehicle speed may varyslightly; this is okay.) Ifyou cannot do this for acontinuous 90 seconds becauseof traffic conditions, drive for atleast 30 seconds, then repeat ittwo more times (for a total of 90 seconds).
Then drive in city/suburbantraffic for at least 10 minutes.When traffic conditions allow,let the vehicle coast for severalseconds without using theaccelerator pedal or the brake pedal.
Make sure the vehicle has beenparked with the engine off for 30 minutes.
If the testing facility determines thereadiness codes are still not set, seeyour dealer.
7. 8.
9.
Emissions Testing
391
12/07/13 17:26:36 31TM8630_396
TechnicalInform
ation
TOC
2013 Insight
The following products and systemson your vehicle emit radio waveswhen in operation.
HandsFreeLinkImmobilizer System
Remote Transmitter
Tire Pressure MonitoringSystem (TPMS)
Each of the above complies with theappropriate requirements or therequired standards of FCC (FederalCommunications Commission) andIndustry Canada Standard, describedas follows:
Bluetooth
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thefollowing two conditions: (1) This devicemay not cause harmful interference, and(2) this device must accept anyinterference received, includinginterference that may cause undesiredoperation.
Changes or modifications not expresslyapproved by the party responsible forcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-Gen/210/310.Operation is subject to the following twoconditions: (1) this device may not causeinterference, and (2) this device mustaccept any interference, includinginterference that may cause undesiredoperation of the device.
Devices that Emit Radio Waves
392
12/07/13 17:26:43 31TM8630_397
TechnicalInform
ation
TOC
2013 Insight
....Customer Service Information . 394....................Warranty Coverages . 395
.............Reporting Safety Defects . 396.....................Authorized Manuals . 397
Warranty and Customer Relations
Warranty
andC
ustomer
Relations
393
12/07/13 17:26:46 31TM8630_398
2013 Insight
Honda dealership personnel aretrained professionals. They shouldbe able to answer all your questions.If you encounter a problem that yourdealership does not solve to yoursatisfaction, please discuss it withthe dealership’s management. Theservice manager or general managercan help. Almost all problems aresolved in this way.
If you are dissatisfied with thedecision made by the dealership’smanagement, contact HondaCustomer Service.
U.S. Owners:
Canadian Owners: When you call or write, please giveus this information:
Vehicle Identification Number(see page )
Name and address of the dealerwho services your vehicle
Date of purchase
Odometer reading of your vehicle
Your name, address, and tele-phone number
A detailed description of theproblem
Name of the dealer who sold thevehicle to you
In Puerto Rico and theU.S. Virgin Islands:
378
Customer Service Information
394
American Honda Motor Co., Inc.Honda Automobile Customer ServiceMail Stop 500-2N-7A1919 Torrance BoulevardTorrance, California 90501-2746
Tel: (800) 999-1009
Honda Canada Inc.Customer Relations180 Honda BoulevardMarkham, ONL6C 0H9
Tel: 1-888-9-HONDA-9Fax: 1-877-939-0909E-Mail: honda_cr@ch.honda.com
Bella InternationalP.O. Box 190816San Juan, PR 00919-0816
Tel: (787) 620-7546
12/07/13 17:26:54 31TM8630_399
Warranty
andC
ustomer
Relations
TOC
2013 Insight
-
--
-
-
-
-
-
Your new vehicle is covered bythese warranties:
providescoverage for as long as the purchaserof the muffler owns the vehicle
provides proratedcoverage for a replacement batterypurchased from your dealer.
a seatbelt that fails to function properly iscovered by a limited warranty.Please read your warranty bookletfor details.
covers all Hondareplacement parts against defects inmaterials and workmanship.
Honda accessories are coveredunder this warranty. Time andmileage limits depend on the typeof accessory and other factors.Please read your warranty bookletfor details.
all exterior body panels arecovered for rust-through from theinside for the specified time periodwith no mileage limit.
covers your new vehicle, except forthe emissions control systems andaccessories, against defects inmaterials and workmanship.
these twowarranties cover your vehicle’semissions control systems. Time,mileage, and coverage areconditional. Please read yourwarranty booklet for exactinformation.
Please refer to the 2013 warrantymanual that came with your vehicle.
Restrictions and exclusions apply toall these warranties. Please read the2013 Honda warranty informationbooklet that came with your vehiclefor precise information on warrantycoverages. Your vehicle’s originaltires are covered by theirmanufacturer. Tire warrantyinformation is in a separate booklet.
Warranty Coverages
U.S. Owners
Canadian Owners
Replacement Muffler LifetimeLimited Warranty
Replacement Battery LimitedWarranty
Seat Belt Limited Warranty
Replacement Parts LimitedWarranty
Accessory Limited Warranty
Rust Perforation Limited Warranty
New Vehicle Limited Warranty
Emissions Control Systems DefectsWarranty and EmissionsPerformance Warranty
395
12/07/13 17:27:02 31TM8630_400
Warranty
andC
ustomer
Relations
TOC
2013 Insight
If you believe that your vehicle has a defect whichcould cause a crash or could cause injury or death, youshould immediately inform the National HighwayTraffic Safety Administration (NHTSA), in addition tonotifying American Honda Motor Co., Inc.
If NHTSA receives similar complaints, it may open aninvestigation, and if it finds that a safety defect exists ina group of vehicles, it may order a recall and remedycampaign. However, NHTSA cannot become involvedin individual problems between you, your dealer, orAmerican Honda Motor Co., Inc.
To contact NHTSA, you may:call the Vehicle Safety Hotline toll-free at
1-888-327-4236 (TTY: 1-800-424-9153);
go to ;
or write to: Administrator NHTSA1200 New Jersey Avenue, SE.Washington, DC 20590.
You can also obtain other information about motorvehicle safety from .
If you believe that your vehicle has a defect which couldcause a crash or could cause injury or death, you shouldimmediately inform Honda Canada Inc. and you may alsoinform Transport Canada.
To contact Transport Canada’s Defect Investigations andRecalls Division, you may call 1-800-333-0510. For moreinformation on reporting safety defects or about motorvehicle safety, go to .
If Transport Canada receives similar complaints, it mayopen an investigation, and if it finds that a safety defectexists in a group of vehicles, it may lead to a recall andremedy campaign. However, Transport Canada cannotbecome involved in individual problems between you,your dealer, or Honda Canada Inc.
Reporting Safety Defects
In the US In Canada
396
http://www.saf ercar.gov
http://www.saf ercar.gov
http://www.tc.gc.ca/roadsaf ety
12/07/13 17:27:08 31TM8630_401
Warranty
andC
ustomer
Relations
TOC
,
2013 Insight
The publications shown below can be purchased from HelmIncorporated. You can order by phone or online:
Call Helm Inc. at 1-800-782-4356 (credit card orders only)Go online at
If you are interested in other years or models, contact Helm Inc.at 1-800-782-4356.
Covers maintenance and recommended procedures forrepair to engine and chassis components. It is writtenfor the journeyman mechanic, but it is simple enoughfor most mechanically inclined owners to understand.
Complements the Service Manual by providing in-depthtroubleshooting information for each electrical circuitin your vehicle.
Describes the procedures involved in the replacementof damaged body parts.
Purchasing Factory Authorized Manuals Service Manual:
Electrical Troubleshooting Manual:
Body Repair Manual:
(U.S. only)
Authorized Manuals
Authorized
Manuals
397
Form Description
2013 Honda Insight Service Manual
2013 Honda Insight
Electrical Troubleshooting Manual
2013 Model Series Honda Insight
Body Repair Manual
2013 Honda Insight Owner’s Manual
2013 Honda Insight
Navigation System Owner’s Manual
2013 Honda Insight Honda Service History
2013 Honda Insight
Technology Reference Guide (LX/EX)
2013 Honda Insight
Technology Reference Guide (EX with Navigation)
Order Form for Previous Years-
Indicate Year and Model Desired
Publication
Form Number
61TM803
61TM803EL
61TM830
31TM8630
31TM8830
31TM8M30
31TM8Q30
31TM8S00
HON-R
www.helminc.com
12/07/13 17:27:17 31TM8630_402
2013 Insight
CONTINUED
BatteryCharging System
...........................Indicator . 63, 364............................Jump Starting . 358
..............................Maintenance . 344............................Specifications . 381
..............................Before Driving . 243....................................Belts, Seat . 9, 21
...........................Beverage Holder . 154.......Bluetooth HandsFreeLink . 225
Brakes...........Anti-lock System (ABS) . 287
.............Break-in, New Linings . 244....................Bulb Replacement . 330
...........................................Fluid . 319...................Pad Wear Indicator . 286
.......................................Parking . 151...........System Indicator . 63, 64, 366
....................................Accessories . 254ACCESSORY (Ignition Key
.....................................Position) . 131.............Accessory Power Socket . 155
................Active Head Restraints . 144....................Additives, Engine Oil . 311
.............................Airbag (SRS) . 10, 25...Airbags, Additional Information . 25...Additional Safety Precautions . 37
..........Advanced Airbag System . 30.............................Airbag Service . 36
How the Passenger Airbag Off......................Indicator Works . 35
How the Side Airbag Off......................Indicator Works . 34
..How the SRS Indicator Works . 34How Your Front Airbags
.........................................Work . 28...How Your Side Airbags Work . 32
How Your Side Curtain Airbags.........................................Work . 33
........................SRS Components . 25..............Air Conditioning System . 162
.......................Air Pressure, Tires . 339
................................Ambient Meter . 72......................................Antifreeze . 315
Anti-lock Brakes (ABS)...............................Indicator . 64, 287
...................................Operation . 287..............Anti-theft, Audio System . 219
Anti-theft Steering Column............................................Lock . 131..........................................Armrest . 146
................................Audio System . 168.......................Auto Door Locking . 109
...................Auto Door Unlocking . 110................................Auto Idle Stop . 281
...Automatic Seat Belt Tensioners . 23.............Automatic Speed Control . 222
.Automatic Transmission (CVT) . 271..........................Capacity, Fluid . 380
...............Checking Fluid Level . 318Paddle Shifters in the
..............................D Position . 276Paddle Shifters in the
...............................S Position . 279.....Recommended Shift Points . 280
.......................................Shifting . 272Shift Lever Position
...............................Indicators . 271
................Shift Lever Positions . 273....................Shift Lock Release . 275
......................Auxiliary Input Jack . 218
I
12/07/23 10:21:22 31TM8630_404
Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
A
B
2013 Insight
.............................Braking System . 285.................Break-in, New Vehicle . 244
Brightness Control,...............................Instruments . 124
Bulb Replacement..........................Back-up Lights . 327
..............................Brake Lights . 330........Front Side Marker Lights . 326.........Front Turn Signal Lights . 325
.................................Headlights . 321..........................Parking Lights . 324
..........Rear Turn Signal Lights . 327............................Specifications . 381
..............................Bulbs, Halogen . 321
..........................Cargo Area Light . 160............................Capacities Chart . 380
.............Carbon Monoxide Hazard . 56.............................Carrying Cargo . 256
.............CAUTION, Explanation of . iii..................................Ceiling Light . 159
..............................Center Pockets . 157...................................Center Tray . 156
........................Certification Label . 378
............................................Chains . 342....................Changing a Flat Tire . 349
Changing Oil........................................How to . 312......................................When to . 299
...Charging System Indicator . 63, 364............Checklist, Before Driving . 262
.....................................Child Safety . 38Child Seats
.............LATCH Anchor System . 47.............................Lower Anchor . 47............................Tether Anchor . 51
................Childproof Door Locks . 134.............................Climate Control . 162
.........................Clock, Setting the . 220........................CO in the Exhaust . 387
............Cold Weather, Starting in . 263..............................Compact Spare . 348
.................Console Compartment . 155.............Controls, Instruments and . 59
Coolant........................................Adding . 315
....................................Checking . 250.........................Proper Solution . 315
...............Temperature Indicator . 67
Crankcase Emissions Control........................................System . 387
............Cruise Control Operation . 222.........................Customer Service . 394
...............DANGER, Explanation of . iii...................................Dashboard . 3, 60
..............Daytime Running Lights . 123............Defects, Reporting Safety . 396
..............Defogger, Rear Window . 126
......Defrosting the Windows . 165, 166....................................Dimensions . 380
.............Dimming the Headlights . 120Dipstick
..........Automatic Transmission . 318..................................Engine Oil . 249
........................Directional Signals . 120Disc Brake Pad Wear
...................................Indicators . 286............................Disc Player . 173, 188
.....................Disposal of Used Oil . 314
II
12/07/23 10:21:26 31TM8630_405
Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
C
D
2013 Insight
CONTINUED
Doors...................Auto Door Locking . 109
...............Auto Door Unlocking . 110............Childproof Door Locks . 134............Locking and Unlocking . 133..........DOT Tire Quality Grading . 382
...........Driver and Passenger Safety . 5...........................................Driving . 261
....................................Economy . 251..................Dust and Pollen Filter . 332
...................................Fan, Interior . 164.........................................Features . 161
....................Filling the Fuel Tank . 245Filters
.........................Dust and Pollen . 332...............................................Oil . 313
...........Flashers, Hazard Warning . 125...................Flat Tire, Changing a . 349
.....................................Floor Mats . 331Fluids
..........Automatic Transmission . 318..........................................Brake . 319
..................Windshield Washer . 317FM Stereo Radio
...................................Reception . 212........................Four-way Flashers . 125
............................Front Airbags . 10, 25
........................Eco Assist System . 264................Ecological Drive Display . 81
................................ECON Button . 127..................................ECON Mode . 127
..............................Economy, Fuel . 251............Emergencies on the Road . 347.............Battery, Jump Starting . 358.....Brake System Indicator . 63, 366
................Changing a Flat Tire . 349Charging System
...........................Indicator . 63, 364..................Checking the Fuses . 369
Low Oil Pressure...........................Indicator . 62, 363
Malfunction Indicator................................Lamp . 62, 365
..................Overheated Engine . 360.........................Emergency Brake . 151
....................Emergency Flashers . 125...........Emergency Hatch Opener . 140
......................Emergency Towing . 374.......................Emissions Controls . 387........................Emissions Testing . 390
Engine............Adding Engine Coolant . 315
Coolant Temperature...................................Indicator . 67
.........................If It Won’t Start . 356Malfunction Indicator
................................Lamp . 62, 365.........................Oil Life Display . 299
........Oil Pressure Indicator . 62, 363
..............Oil, What Kind to Use . 310...............................Overheating . 360
............................Specifications . 380
............................Speed Limiter . 274.......................................Starting . 263
.Evaporative Emissions Controls . 387
...............................Exhaust Fumes . 56Expectant Mothers, Use of Seat
........................................Belts by . 19
IndexIN
DE
X
III
12/07/23 10:21:32 31TM8630_406
Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
E
F
2013 Insight
.................................................Fuel . 244......................Fill Door and Cap . 245
...........................................Gauge . 73................Octane Requirement . 244
...............................Oxygenated . 244........................Reserve Indicator . 70
........................Tank, Filling the . 245.....................Fuses, Checking the . 369
...............Gas Mileage, Improving . 251.........................................Gasoline . 244
...............Fuel Reserve Indicator . 70...........................................Gauge . 73
................Octane Requirement . 244........................Tank, Filling the . 245
................Gas Station Procedures . 245Gauges
.............................Charge/Assist . 74...............................................Fuel . 73
............Gearshift Lever Positions . 271..........Automatic Transmission . 271
......................................Glove Box . 156
.............Halogen Headlight Bulbs . 321...........................HandsFreeLink . 225
..............................................Hatch . 139......................................Opening . 139
............................Open Indicator . 68............Hazard Warning Flashers . 125
Headlights........................................Aiming . 321
.........Daytime Running Lights . 123..................High Beam Indicator . 69
......................Reminder Beeper . 121........Replacing Halogen Bulbs . 321
.................................Turning on . 121............................Head Restraints . 142.............................Heated Mirrors . 148
.............High Altitude, Starting at . 263...............High-Low Beam Switch . 120...............Hill Start Assist System . 295
.......................Hood, Opening the . 248....................................................Horn . 4
...Identification Number, Vehicle . 378
Ignition............................................Keys . 129
.........................................Switch . 131............Timing Control System . 388
IMA System Power Flow........................................Monitor . 84
......................Immobilizer System . 130.........Important Safety Precautions . 6
.........Indicators, Instrument Panel . 62
...Indicators, Messages (MID) . 62, 89...............ABS (Anti-lock Brake) . 64
..............................Auto Idle Stop . 66Brake (Parking and Brake
............................System) . 63, 366.............................Cruise Control . 69
.................................Cruise Main . 69................Door/Hatch Open . 12, 68
DRL (Daytime Running....................................Lights) . 123
.EPS (Electric Power Steering) . 68................................ECON Mode . 71
...................................High Beam . 69....High Temperature (Coolant) . 67
......................IMA Battery Level . 85.................................IMA System . 66
........Key (Immobilizer System) . 63
IV
12/07/13 17:27:39 31TM8630_407
Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
G
H
I
2013 Insight
CONTINUED
................................................Keys . 129
.................Jacking up the Vehicle . 351.......................................Jack, Tire . 350
................................Jump Starting . 358
Indicators, Messages (MID).....................................Lights On . 69......................................Low Fuel . 70
................Low Oil Pressure . 62, 363.....Low Temperature (Coolant) . 67
Low Tire Pressure/...............................TPMS . 66, 289
...Malfunction Indicator Lamp . 365..........................Security System . 70...........................Side Airbag Off . 65
.................................Seat Belt . 21, 62.........................................SRS . 34, 64
.........................System Message . 70...........................TPMS . 66, 289, 290
Turn Signal and Hazard...................................Warning . 69
12 Volt Battery Charging..............................System . 63, 364
........................................VSA Off . 65.................................VSA System . 65...............................Infant Restraint . 43
Infant Seats......LATCH Anchorage System . 47
...........................Lower Anchors . 47
...........................Tether Anchors . 51
.....Inflation, Recommended Tire . 338...................................Pressures . 339
........................Information Display . 72.................................Inside Mirror . 147
.............................Inspection, Tire . 339............................Instrument Panel . 61
......Instrument Panel Brightness . 124...............................Interior Lights . 159
........................................Introduction . i...............................................iPod . 195
.......................Label, Certification . 378...............Lane Change, Signaling . 121
..................Lap/Shoulder Belts . 17, 22
...........LATCH Anchorage System . 47Lights
....................Bulb Replacement . 321.......................................Indicator . 69
.......................................Parking . 120..........................Turn Signal . 69, 120
....................................Load Limits . 257....LOCK (Ignition Key Position) . 131
Locks.....Anti-theft Steering Column . 131
............................Fuel Fill Door . 245..........................................Hatch . 139
...............................Power Door . 133........................Low Coolant Level . 250.........................Low Fuel Indicator . 70
................................Lower Anchors . 47...Low Oil Pressure Indicator . 62, 363
...Lubricant Specifications Chart . 380
IND
EX
V
12/07/23 10:21:38 31TM8630_408
Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
J
K
L
2013 Insight
..................................Maintenance . 297......Main Items and Sub Items . 304
........................................Minder . 299Owner’s Maintenance
...................................Checks . 307..........................................Safety . 298
.Malfunction Indicator Lamp . 62, 365.........................Meters, Gauges . 61, 72
...................Methanol in Gasoline . 244...........................................Mirrors . 147
....................................Adjusting . 147........................................Heated . 148
...................Neutral Gear Position . 273..................New Vehicle Break-in . 244
...................NOTICE, Explanation of . i...............Numbers, Identification . 378
..............................Paddle Shifters . 276............Panel Brightness Control . 124
........................Park Gear Position . 273...........................................Parking . 284
...............................Parking Brake . 151Parking Brake and Brake
.................System Indicator . 63, 366...............................Parking Lights . 120
..Parking Over Things that Burn . 284
.............................PGM-FI System . 388..................Playing the Radio . 169, 181
........................Playing a Disc . 173, 188............................Playing an iPod . 195
Playing a USB Flash Memory........................................Device . 202
...................................Pollen Filter . 332.........Pregnancy, Using Seat Belts . 19.........Protecting Adults and Teens . 12
...Additional Safety Precautions . 20.....Advice for Pregnant Women . 19
........................Protecting Children . 38.......................Protecting Infants . 43
.......Protecting Larger Children . 52.........Protecting Small Children . 44
...Octane Requirement, Gasoline . 244.........................................Odometer . 79
Oil........................Change, How to . 312......................Change, When to . 299......................Checking Engine . 249..............Pressure Indicator . 62, 363
.......Selecting Proper Viscosity . 311.........ON (Ignition Key Position) . 132
Onboard Refueling Vapor....................................Recovery . 387
............................Outside Mirrors . 147....Outside Temperature Indicator . 80
....................Overheating, Engine . 360....Owner’s Maintenance Checks . 307
.........................Oxygenated Fuels . 244
...................Radiator Overheating . 360..........Radio/Disc/Sound System . 168
.................Radio Theft Protection . 219...................Readiness Codes . 365, 390
Rear Lights, Bulb..............................Replacement . 327
..........................Rear View Mirror . 147...............Rear Window Defogger . 126
VI
12/07/23 10:21:44 31TM8630_409
Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
M
N
O
P Q
R
2013 Insight
CONTINUED
..................................Safety Belts . 9, 21............Safety Defects, Reporting . 396
.................................Safety Features . 8.........................................Airbags . 10
.......................................Seat Belts . 9.............Safety Labels, Location of . 57
..............................Safety Messages . iii.....................................Seat Belts . 9, 21
...............Additional Information . 21Automatic Seat Belt
...............................Tensioners . 23.....................................Cleaning . 331
................Lap/Shoulder Belt . 17, 22........................Maintenance . 24, 331
Reminder Light and................................Beeper . 21, 62
...................System Components . 21...............Use During Pregnancy . 19
Wearing a Lap/Shoulder.....................................Belt . 17, 22
......................Seats, Adjusting the . 141............................Security System . 221
...............................Serial Number . 378...........................Service Intervals . 308
.............................Service Manual . 397.........Service Station Procedures . 245
..........................Setting the Clock . 220...Shift Lever Position Indicators . 271
........................Shift Lock Release . 275..............................Side Airbags . 10, 32
..........................Off Indicator . 34, 65......................Side Curtain Airbags . 33
Side Marker Lights, Bulb..............................Replacement . 326.............................Signaling Turns . 121
.....................................Snow Tires . 342Spare Tire
......................................Inflating . 348............................Specifications . 381
....................Specifications Charts . 380................................Speed Control . 222
Speed-Sensitive Volume...............Compensation (SVC) . 187
.......................................Spotlights . 159
..............Reclining the Seat-backs . 141.........Recommended Shift Points . 280
................Remote Audio Controls . 217.....................Remote Transmitter . 135
Replacement Information..............Dust and Pollen Filter . 332
................Engine Oil and Filter . 312..........................................Fuses . 369
................................Light Bulbs . 321.............Maintenance Minder . 299
...........................................Tires . 341.............................Wiper Blades . 332
Replacing Seat Belts After a............................................Crash . 24
.............Reporting Safety Defects . 396Reserve Tank, Engine
...............................Coolant . 250, 315...............................Restraint, Child . 38
..................Reverse Gear Position . 273................................Rotation, Tire . 341
IND
EX
VII
TM
12/07/23 10:21:49 31TM8630_410
Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
S
2013 Insight
..........SRS, Additional Information . 25...Additional Safety Precautions . 37
..........Advanced Airbag System . 30.............................Airbag Service . 36
How the Passenger Airbag Off......................Indicator Works . 35
How the Side Airbag Off......................Indicator Works . 34
..How the SRS Indicator Works . 34How Your Front Airbags
.........................................Work . 28...How Your Side Airbags Work . 32
How Your Side Curtain..........................Airbags Work . 33........................SRS Components . 25
.............................SRS Indicator . 34, 64..START (Ignition Key Position) . 132
.......................Starting the Engine . 263In Cold Weather at High
..................................Altitude . 263................With a Dead Battery . 358
........Steam Coming from Engine . 360Steering Wheel
..............................Adjustments . 128...........Anti-theft Column Lock . 131
....................Storing Your Vehicle . 346
......................................Sun Visors . 158Supplemental Restraint System
......................................Servicing . 36.........................SRS Indicator . 34, 64
...................System Components . 25.................................................SVC . 187
..................................Synthetic Oil . 311
Taillights, Changing..........................................Bulbs . 330
.Taking Care of the Unexpected . 347Technical Descriptions
......DOT Tire Quality Grading . 382.....Emissions Control Systems . 387
....................Emissions Testing . 390.....................Oxygenated Fuels . 244
Three Way Catalytic...............................Converter . 389
...................Temperature Indicator . 67..............Tether Anchorage Points . 51
............................Theft Protection . 219Three Way Catalytic
...........................Converter . 388, 389
Tighten Fuel.............................Cap Message . 247
..........................Time, Setting the . 220....................................Tire Chains . 342
.........Tire, How to Change a Flat . 349...........................Tire Information . 382
.................................Tire Labeling . 383Tire Pressure Monitoring
............System (TPMS) . 289, 385.............................Check TPMS . 385
Low Tire Pressure/TPMS...........................Indicator . 66, 289
Required Federal............................Explanation . 385
...............................................Tires . 338..............................Air Pressure . 339
........................................Chains . 342.........................Checking Wear . 340..........................Compact Spare . 348
......DOT Tire Quality Grading . 382......................................Inflation . 338
..................................Inspection . 339..............................Maintenance . 340
...................................Replacing . 341......................................Rotating . 341
................................Service Life . 340
VIII
12/07/23 10:21:53 31TM8630_411
Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
T
2013 Insight
Tires...........................................Snow . 342
............................Specifications . 381...................Tools, Tire Changing . 350
Towing.....................................A Trailer . 296
..................Emergency Towing . 374Transmission
Checking Fluid Level,..............................Automatic . 318
...........................Fluid Selection . 319..............Identification Number . 379.............Shifting the Automatic . 272
.....................................Treadwear . 340
.......................................Trip Meter . 79..................................Turn Signals . 121
Unexpected, Taking Care..........................................of the . 347
....Uniform Tire Quality Grading . 382........................Unleaded Gasoline . 244......................USB Adapter Cable . 205
.........USB Flash Memory Device . 203.......Used Oil, How to Dispose of . 314
................................Vanity Mirror . 158.................Vehicle Capacity Load . 257
......................Vehicle Dimensions . 380....Vehicle Identification Number . 378
Vehicle Stability Assist (VSA )....................................System . 293
.............VSA OFF Indicator . 65, 293.........................VSA Off Switch . 294
........VSA System Indicator . 65, 293.............................Vehicle Storage . 346
.....................................Ventilation . 165.................................................VIN . 378
..................................Viscosity, Oil . 311
............WARNING, Explanation of . iii.........Warning Labels, Location of . 57
....................Warranty Coverages . 395Washer, Windshield
........Checking the Fluid Level . 317...................................Operation . 119
Wheels.............Adjusting the Steering . 128
............Alignment and Balance . 340.....................................Cleaning . 343
..........................Compact Spare . 348...............................Nut Wrench . 350
Windows.............................Auto Reverse . 150
................Operating the Power . 149.........................Rear, Defogger . 126
Windshield.....................................Cleaning . 119...................................Defroster . 166
.....................................Washers . 119Wipers, Windshield
.......................Changing Blades . 332...................................Operation . 119....................................Worn Tires . 339
.....Wrecker, Emergency Towing . 374
IND
EX
IX
12/07/23 10:21:58 31TM8630_412
Index A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
U
V
W X Y Z
2013 Insight
Service Information Summary
Gasoline:
Fuel Tank Capacity:
Brake Fluid:
Tire Pressure (measured cold):Recommended Engine Oil:
Automatic Transmission Fluid(CVTF):
33 psi (230 kPa , 2.3 kgf/cm )
60 psi (420 kPa , 4.2 kgf/cm )
Honda Heavy Duty Brake FluidDOT 3 preferred, or a DOT 3 orDOT 4 brake fluid as a temporaryreplacement (see page ).
Front/Rear:
Spare Tire:
Unleaded gasoline, pump octanenumber of 87 or higher.
API Premium grade 0W-20detergent oil (see page ).
Oil change capacity (includingfilter):
3.4 US qt (3.2 )
Use Honda CVT Fluid(continuously variabletransmission fluid) only
Fluid change capacity:3.0 US qt (2.8 )
10.6 US gal (40 )
360
319
12/07/23 10:22:09 31TM8630_413
2013 Insight
This owner’s manual should be considered apermanent part of the vehicle and shouldremain with the vehicle when it is sold.
This owner’s manual covers all models of theInsight. You may find descriptions ofequipment and features that are not on yourparticular model.
Images throughout this owner’s manual(including the front cover) represent featuresand equipment that are available on some,but not all, models. Your particular modelmay not have some of these features.
The information and specifications includedin this publication were in effect at the timeof approval for printing. Honda Motor Co.,Ltd. reserves the right, however, todiscontinue or change specifications ordesign at any time without notice and withoutincurring any obligation whatsoever.
Owner’s Identif ication
OWNER
ADDRESS
V. I. N.
DELIVERY DATE
DEALER NAME DEALER NO.
ADDRESS
OWNER’S SIGNATURE
DEALER’S SIGNATURE
STREET
CITY STATE/PROVINCE/TERRITORY ZIP CODE/POSTAL CODE
(Date sold to original retail purchaser)
STREET
CITY STATE/PROVINCE/TERRITORY ZIP CODE/POSTAL CODE
12/07/13 16:36:19 31TM8630_001
2013 Insight