Post on 18-Jul-2020
transcript
Kitchen RangeCustomer Care Guide
Receiving and Installing your New Kitchen
i nspira tion for your kitchen
2 inspiration for your home
Section 1: Your Guide to Components Received
Section 2: Fittings Guide
Section 3: Handy Hints on Preparation and Installation
Section 4: Installation Sequence
Section 5: Finishing Touches - Door Installation
Section 6: Finishing Touches - Show End Fitting
Section 7: Finishing Touches - Wirework; 600 Pullout
Section 8: Caring for your Kitchen
Section 9: Key Unit Dimensions
Before you install your Kitchen, please read the ‘Home Delivered Products’ leaflet as it is used in conjunction with this guide. This leaflet has been included with this guide.
These guidelines are not a substitute for professional advice. Whilst every care has been taken to ensure that the product design, descriptions, specifications and techniques of constructing the products are accurate at the date of printing, Wickes products will inevitably change from time to time and the customer is advised to check the design, descriptions, specifications and techniques of any of the products described in this leaflet are still valid at the time of purchase or placing an order. Where these guidelines vary from the instructions on a product or its packaging, then the instructions on the product or packaging should be followed.
Contents
Important Information
Note: It is not advisable to fit timber doors in newly constructed or recently plastered rooms. A high moisture content in the environment may cause the doors to swell and split. It is recommended that doors are stored outside the kitchen until the room has dried out thoroughly.
Wickes Customer ServiceOur advisors at our National Customer Service Centre are dedicated to helping you to make your project a success. If you need any additional support please contact us on
We are open: Monday - Friday: 9am - 5:30pm
* For training purposes and security, our calls may be recorded.
0844 892 2721*.
3
Base Units Handles Additional Items
CarcaseHighline
300 Highline Base 1
1
1
1
2
1
1
400 Highline Base
500 Highline Base
600 Highline Base
800 Highline Base
1000 Highline Base
800 Highline Corner Base
1000 Highline Corner Base
FasciaOrdered Item: Component Received:
Section 1: Your Guide to Components Received
Assembly Instructions and fittings contained in this pack.
2
Base Units CarcaseDrawerline
300 Drawerline Base
400 Drawerline Base
500 Drawerline Base
600 Drawerline Base
800 Drawerline Base
1000 Drawerline Base
1000 Drawerline Corner Base
800 Drawerline Corner Base
Assembly Instructions and fittings contained in this pack.
800 Drawerline Sink/Hob
500 Drawerline Sink
600 Drawerline Sink/Hob
1000 Drawerline Sink/Hob
Fascia TandemDrawer Box
Handles Additional Items
2
2
2
2
4
4
2
2
2
2
4
4
(F3) 300 Highline Fascia
(F4) 400 Highline Fascia
(F5) 500 Highline Fascia
(F6) 600 Highline Fascia
2 x 400 Highline Fascia(F4)
2 x 500 Highline Fascia(F5)
(F4) 400 Highline Fascia
(F5) 500 Highline Fascia
(FB3) 300 Drawerline Fascia
(FB4) 400 Drawerline Fascia
(FB5) 500 Drawerline Fascia
(FB6) 600 Drawerline Fascia
2 x 400 Drawerline Fascia(FB4)
2 x 500 Drawerline Fascia(FB5)
(FB5) 500 Drawerline Fascia
(FB4) 400 Drawerline Fascia
2 x 400 Drawerline Fascia(FB4)
500 Drawerline Fascia(FB5)
600 Drawerline Fascia(FB6)
2 x 500 Drawerline Fascia(FB5)
1 x (KQQDS3T) 300 Single Drawer Set
1 x (KQQDS4T) 400 Single Drawer Set
2 x (KQQDS4T) 400 Single Drawer Set
2 x (KQQDS5T) 500 Single Drawer Set
1 x (KQQDS5T) 500 Single Drawer Set
1 x (KQQDS6T) 600 Single Drawer Set
1 x (KQQDS5T) 500 Single Drawer Set
1 x (KQQDS4T) 400 Single Drawer Set
1 x (KQQDS5T) 500 Single Drawer Set
(NRLZB5)500 Base/Sink Cabinet
(NRLZB4)400 Base Cabinet
(NRLZB3) 300 Base Cabinet
(NRLZB10)1000 Base/Sink /Hob Cabinet
(NRLZB8)800 Base/Sink /Hob Cabinet
(NRLZB6)600 Base/Sink /Hob Cabinet
(NRLZB10)1000 Base/Sink /Hob Cabinet
(NRLZB8)800 Base/Sink /Hob Cabinet
(NRLZB5)500 Base/Sink Cabinet
(NRLZB4)400 Base Cabinet
(NRLZB3) 300 Base Cabinet
(NRLZB6)600 Base/Sink /Hob Cabinet
(NRLZB10)1000 Base/Sink /Hob Cabinet
(NRLZB8)800 Base/Sink /Hob Cabinet
(NRLZB10)1000 Base/Sink /Hob Cabinet
(NRLZB8)800 Base/Sink /Hob Cabinet
(NRLZB6)600 Base/Sink /Hob Cabinet
(NRLZB5)500 Base/Sink /Hob Cabinet
(NRLZB10)1000 Base/Sink /Hob Cabinet
(NRLZB8)800 Base/Sink /Hob Cabinet
Many items in the Wickes stores are made up of a number of compo-nents. This is a guide to the components you will receive. The drawing and description on the left is how the item was ordered. On the right is how the components will be shipped.Note: Certain items, Pelmet, Cornice, Plinth, Tongue and Groove End Panels and Worktops, are supplied overlength to allow clean cutting to size
Important: Small items such as handles, small gallery rails and screw packs for cornice and pelmets are packed in the small parts box/bag that comes with your delivery.Cabinet Component Colour: The cabinets are supplied in an off-white coloured board. Due to variations in supply, the colour of the component panels may be different even within a single unit.
4 ins pira tion for your home
Ordered Item: Component Received:Base Units CarcaseDrawer Pack and Pan Drawers
300 Drawer Pack
600 Pan Drawer
Assembly Instructions and fittings contained in this pack.
900 Pan Drawer
Fascia Additional Items
Handles
4
3
6/3
TandemDrawer Box
(FD3) 300 Drawer Pack Fascia
(FPD6) 600 Pan Drawer Fascia
900 Pan Drawer Fascia(FPD9)
1 x (GRLPD6T)600 Pan Drawer Set
1 x (GRLDP3T) 300 Drawer Pack Set
1 x (GRLPD9T)900 Pan Drawer Set
(NRLZPD6)600 Drawer Cabinet
(NRLZD3)300 Drawer Cabinet
(NRLZPDBU9)900 Pan Drawer/ Under Oven Cabinet
Base Units CarcaseBuilt-Under Oven Units
600 Under Oven Housing(NRLZBU6)600 Under Oven Cabinet
900 Under Oven Housing(NRLZPDBU9)900 Pan Drawer/Under Oven Cabinet
Assembly Instructions and fittings contained in this pack.
Handles
600 Single Oven
1
Appliance
900 Single Oven
Base Units CarcaseBelfast Sink Units and Butler Support Units Assembly Instructions and fittings
contained in this pack.
Handles Additional Items
600 Belfast Sink UnitWith Door
(BSSU6)600 Belfast Sink Cabinet 1
900 Belfast Sink UnitWith Door(not available all ranges)
(NRLZBSSU9)900 Belfast Sink Cabinet 2
600mm Wide Butler Sink For 28mm Thick Worktops
600mm Wide Butler Sink For 38mm Thick Worktops
(NRZLBSSU6)600 Butler Sink Support Unit
(NRLZBSSU6)600 Butler Sink Support Unit
Fascia
(FBU6)131 x 600 Fascia
(FBU9) (Stainless Steel Effect Only)Includes Drawer Box
203 x 896 Drawer Fascia
(IN44) 44 x 896 Filler
Fascia
437(FCH) x 596 Fascia
2 x 437(FBS45) x 446 Fascia
1 x (IN110) 1 x (FCH) 437 x 596 Fascia
110 x 596 Filler
1 x ( ) 1311 x (FCH) 437 x 596 Fascia
FBU6 x 596 Filler
1
1
500 Drawer Pack (FD5) 500 Drawer Pack Fascia 1 x (GRLDP5T) 500 Drawer Pack Set
(NRLZD5)500 Drawer Cabinet
900 2-Pan Drawer 4/2
6/3
900 2-Pan Drawer Fascia(FPD92) 1 x (KQQPD92T)900 2-Pan Drawer Set
1 x (GRLPD93CT)Curved Pan Drawer Set
(NRLZPDBU9)900 Pan Drawer/ Under Oven Cabinet
(NRLZPDBU9)900 Pan Drawer/ Under Oven Cabinet
900 3-Drawer Curved Drawer Unit(FPD9C) Curved 900 Pan Drawer Fascia
5
FasciaBase Units Carcase
'L' Shape Corner Base
2 x 300 Drawerline Fascia(FB3)
2 x 300 Drawerline Fascia(FB3)
2 x 300 Highline Fascia(F3)
2 x 300 Highline Fascia(F3)
925 Corner Base Cabinet (NRLZCB9/1 )Pack 1-Ends & Back(NRLZCB9/2) Pack 2-Shelf Pack
Highline 'L' ShapeCorner Base
Drawerline 'L' ShapeCorner Base
Highline 'L' ShapeCorner BaseWith Carousel
Drawerline 'L' ShapeCorner BaseWith Carousel
Assembly Instructions and fittings contained in this pack.
Handles
1
1
2
2
1 x ¾ Carousel
1 x ¾ Carousel
52 55
52 55
52 55
52 55
BCF735 Base Corner Post
BCF735 Base Corner Post
BCF735 Base Corner Post
BCF735 Base Corner Post
Additional Items
925 Corner Base Cabinet (NRLZCB9/1 )Pack 1-Ends & Back(NRLZCB9/2) Pack 2-Shelf Pack
925 Corner Base Cabinet (NRLZCB9/1 )Pack 1-Ends & Back(NRLZCB9/2) Pack 2-Shelf Pack
925 Corner Base Cabinet (NRLZCB9/1 )Pack 1-Ends & Back(NRLZCB9/2) Pack 2-Shelf Pack
Ordered Item: Component Received:
FasciaBase Units Carcase
Corner Base / Larder
(FSCS) Syncromotion Fascia Set
Syncromotion Ca(NRLZSCC1 )Pack 1-Ends & Back(NRLZSCC2) Pack 2-Shelf Pack
binet Syncromotion Drawer Corner Unit
Assembly Instructions and fittings contained in this pack.
Handles
6
2TMFTall MondoFiller Kit
Additional Items
2 x 2 x (F3) 300 Highline Fascia
(FL3) 1319 x 296 Door FasciaTall Mondo MechanismTall Mondo Corner Unit
(SFK) Syncromotion Filler Kit
SyncromotionFront MechanismKQQSFMS x 1 KQQSFMD x 2
Corner Drawer Set(KQQSCD)
Syncromotion
Drawer Set
CarcaseAssembly Instructions and fittings contained in this pack.
Additional Items /Optional Extras
1
1
500 BaseDisplay Unit
Open (BDU5) Open Display Ca
500 Basebinet
(BDU5) Open Display Ca
500 Basebinet
500 BaseDisplay Unit With Wicker Basket
Open
2 x 500 Wicker Baskets
Handles
1 x 500Single Drawer Set(KQQDS5T)
TandemDrawer Box
1 x 500Single Drawer Set(KQQDS5T)
Base UnitsFeature Units
150 Pull-Out Base Unit(not available all ranges) (NRLZPO15) 150 Pull-Out Cabinet
Fascia
143 x 496 Fascia(FDF5)
143 x 496 Fascia(FDF5)
(FP15) 150 Pull-Out Cabinet 1Pull Out Wirework 150
150 Tray Unit(not available all ranges) (NRLZPO15) 150 Pull-Out Cabinet (TUF) Tray Unit Frame Single Tray
(ST)
600 Concealed Drawer Unit (NRLZB6) binet 600 Base Ca 731 x 596 Fascia(F6) 1
1 x 600 Easyspace Drawer(KQQZISSD6)
2 x 600 Easyspace Drawer(KQQZISDD6)
Ordered Item: Component Received:Wall Units FasciaCarcase Handles Additional
ItemsAssembly Instructions and fittings contained in this pack.
6 ins pira tion for your home
300 Wall Unit (F3) 300 Highline Fascia
400 Wall Unit (F4) 400 Highline Fascia
500 Wall Unit (F5) 500 Highline Fascia
600 Wall Unit (F6) 600 Highline Fascia
600 x 441 Cooker HoodBridging Unit
600 x 294 Cooker HoodBridging Unit
625 Corner Wall Unit
625 L-shapedCorner Wall Unit
(NRLZW3) binet 300 x 735 Wall Ca
(NRLZW4) binet 400 x 735 Wall Ca
(NRLZW5) binet 500 x 735 Wall Ca
(NRLZW6) binet 600 x 735 Wall Ca
(NRLZCW6) 625 x 735 Corner Wall Cabinet
(NRLZCWL6) 625 x 735 Corner Wall Cabinet
(NRLZCH6) binet 600 x 441 Wall Ca (FCH) 437 x 596 Door Fascia
294 Feature Bridging Unit (CHF6) binet 600 x 294 Wall Ca (FCHGDA) Aluminium Feature Door Fascia
290 x 596
1
1
1
1
800 Wall Unit 2 x 400 Highline Fascia(F4)
1000 Wall Unit 2 x 500 Highline Fascia(F5)
800 x 735 Wall Ca(NRLZW8) binet
(NRLZW10) binet 1000 x 735 Wall Ca
2
2
1
1
Includedwith
Fascia
(NRLZCH) binet 600 x 294 Wall Ca (FAH1) 290 x 596 Door Fascia 1
(F4) 400 Highline Fascia
(FCWL6) Pair of doors 285mmwide(includes filler)
600 Corner Wall Unit (NRLZW6) binet 600 x 735 Wall Ca 1(F3) 300 Highline Fascia
(MWC)Conversion Kit
(MHF9) binet 900 x 367 Wall Ca (FMH9) 363 x 896 Door Fascia 1
Feature Units CarcaseAssembly Instructions and fittings contained in this pack.
2
2
2
500 GlassPeninsular Unit
(ODU5) Peninsular Ca
500 Open Displaybinet
(ODU5) Peninsular Ca
500 Open Displaybinet
(ODU5) Peninsular Ca
500 Open Displaybinet
500 MixedPeninsular Unit
500 StandardPeninsular Unit
Handles
800 Decorative Feature Unit
4
( D 8) binet O C 4-Drawer Ca
( DU8) O 800 x 584 Top Box
263mm
270mm
263mm
263mm
270mm
263mm
900 Feature Unit
500 Tambour Unit
(FHF9) 900 Full HeightFeature Cabinet(including mechanism)
(D T) 500 Dresser/Tambour Ca
Cbinet
500 Glass Wall Unit
1000 Glass Wall Unit
(ODU5) 500 x 735 Wall Cabinet
(NRLZW10) 1000 x 735 Wall Cabinet
1
2
Fascia / F rame
2 x 500 Glass Fascia(F5G)
2 x 500 Fascia(F5)
1 x 500 Glass Fascia1 x (F5) 500 Fascia
(F5G)
(ODF8) Frame
(FHD4) Drawer Fascia Set(includes drawer boxes)
2 x (FMH9) 900 Mid Height Feature Fascia
(TM) TambourFascia Mechanism
2 x 500 Glass Fascia(F5G)
(F5G) 500 Glass Fascia
Additional Items /Optional Extras
(GS) Glass Shelf
1
(GS) Glass Shelf
(GS) Glass Shelf
900 Mid HeightFeature Bridging UnitWith Aluminium Feature Door
(MHF9) binet 900 x 367 Wall Ca (FMH9GDA) Aluminium Feature Door Fascia
363 x 896 Includedwith
Fascia
900 Mid HeightFeature Bridging UnitWith Solid Door
Pack of 2 Stays(KQQSP)Certain ranges only
Pack of 2 Stays(KQQSP)Certain ranges only
1
Ordered Item: Component Received:
7
Tall Units Fascia Handles Additional Items AndRecommended Appliances
Carcase
300 & 500 Larders
1319 x 296 Door Fascia
(F3) 300 Highline Fascia
(FL3)
(FL5) 1319 x 496 Door Fascia
(F5) 500 Highline Fascia
2
2500 Larder
300 LarderWith Softclose Pull-Out Rack
300 LarderWith Glass Doors
2 Includedwith
Fascia
1319 x 296 Aluminium Frame Fascia
(F3GDA) 300 Aluminium Frame Fascia
(FL3GDA)
300 LarderWith Glass and Solid Doors
1319 x 296 Aluminium Frame Fascia
(F3) 300 Highline Fascia
(FL3GDA)
1319 x 296 Door Fascia
(F3) 300 Highline Fascia
(FL3)
2300 LarderWith Pull-Out Rack
(TLEP)Larder Decorative Ends
(NRLZHP3) 300 LarderBack & Shelf Pack
(FL5) 1319 x 496 Door Fascia
(F5) 500 Highline Fascia
2 500 Pull-Out RackSoftclose
500 LarderWith Softclose Pull-Out Rack
(FL5) 1319 x 496 Door Fascia
(F5) 500 Highline Fascia
2500 LarderWith Swing-Out Rack Swing-Out Rack
(FL5) 1319 x 496 Door Fascia
(F5) 500 Highline Fascia
2 500 Pull-Out RackStandard
500 LarderWith Standard Pull-Out Rack
1 &1 Included
withFascia
300 Pull-Out RackStandard
300 Pull-Out RackSoftclose
(TLEP)Larder Decorative Ends
(NRLZHP3) 300 LarderBack & Shelf Pack
(TLEP)Larder Decorative Ends
(NRLZHP3) 300 LarderBack & Shelf Pack
(TLEP)Larder Decorative Ends
(NRLZHP3) 300 LarderBack & Shelf Pack
(TLEP)Larder Decorative Ends
(NRLZHP5) 500 LarderBack & Shelf Pack
(TLEP)Larder Decorative Ends
(NRLZHP5) 500 LarderBack & Shelf Pack
(TLEP)Larder Decorative Ends
(NRLZHP5) 500 LarderBack & Shelf Pack
(TLEP)Larder Decorative Ends
(NRLZHP5) 500 LarderBack & Shelf Pack
Assembly Instructions and fittings contained in this pack.
Tall Units Fascia Handles Additional Items AndRecommended Appliances
Carcase
600 LardersAssembly Instructions and fittings contained in this pack.
4 Includedwith
Fascia
2 x (FL3GDA) 1319 x 296 Aluminium Frame Fascia
2 x (F3GDA) 300 Aluminium Frame Fascia
600 LarderWith Glass Doors
2 &2 Included
withFascia
2 x (FL3GDA) 1319 x 296 Aluminium Frame Fascia
2 x (F3) 300 Highline Fascia
600 LarderWith Glass and Solid Doors
(FL6) 1319 x 596 Door Fascia
(F6) 600 Highline Fascia
2600 Larder
(TLEP)Larder Decorative Ends
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
(TLEP)Larder Decorative Ends
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
(TLEP)Larder Decorative Ends
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
8 ins pira tion for your home
Tall Units Fascia Handles Additional Items AndRecommended Appliances
Carcase
600 Larders & Appliance Housings
Ordered Item: Component Received:
Note: All Tall Units are supplied with Decorative Ends. Please read the appliance manufacturer's installation instructions before assembling the Appliance Housing.
Assembly Instructions and fittings contained in this pack.
290 x 596 Door Fascia
(IN110) 110 x 596 Filler Panel
(FCH) 437 x 596 Door Fascia
(FAH1)
584 x 596 Door Fascia
(FAH3) 1025 x 596 Door Fascia
(FCH) 437 x 596 Door Fascia
(FAH2)
(IN110) 110 x 596 Filler Panel
(FCH) 437 x 596 Door Fascia
(FCH) 437 x 596 Door Fascia
(FAH3) 1025 x 596 Door Fascia
(FAH3) 1025 x 596 Door Fascia
2
3
2
2
Tall HousingType 'E'
Appliance
Tall HousingType 'D'
Appliance
Tall HousingType 'C'
Appliance
Tall HousingType 'F'
Appliance
Tall HousingType 'G'
Appliance
437 x 596 Door Fascia
(FBU6) 131 x 596 Filler Panel
(FPD6) 290 x 596 Drawer Fascias(FDSP6 x2 on certain ranges)
(FCH)
437 x 596 Door Fascia
(FBU6) 131 x 596 Filler Panel
(FAH2) 584 x 596 Door Fascia
(FCH)
Double Ovens
Drawer kit KQQPD62T
Double Ovens
Larder Fridge or Freezer
and Freezeror Fridge/FreezerLarder Fridge
Upper Aperture- Lower Aperture- Single Oven
Microwave
Upper Aperture- Lower Aperture- Single Oven
Single Oven
3
2
Tall HousingType 'J’With Pan Drawers
Appliance
Tall HousingType 'B'
Appliance
TAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
TAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
TAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
TAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
TAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
TAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
TAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
(FA6) 600 Highline Fascia
(FL6) 1319 x 596 Door Fascia2 Fridge/Freezer
600 Highline Fascia
(FBU6) 131 x 596 Filler Panel
(FAH2) 584 x 596 Door Fascia
(F6)
Single Oven
Single Oven
Drawer kit KQQPD62T
2
3
Tall Appliance HousingType 'A'
Tall Appliance HousingType 'H’ With Pan Drawers
TAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
TAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
Fascia
(FBU6) 131 x 596 Filler Panel
(FPD6) 290 x 596 Drawer Fascia(FDSP6 x2 on certain ranges)
(F6) 600 Highline
(FCH) 437 x 596 Door Fascia
(IN110) 110 x 596 Filler Panel
(FPD6) Drawer Fascias
2Tall HousingType 'K’With Drawers
Appliance Upper Aperture- Lower Aperture- Single Oven
Drawer kit GRLPD6T
MicrowaveTAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
437 x 596 Door Fascia
(IN110) 110 x 596 Filler Panel
(FAH2) 584 x 596 Door Fascia
(FCH)
Coffee MachineCompact OvenDrinks Machine
2Tall HousingType 'L'
Appliance
TAE6- Pair of Oven Ends*
(NRLZHP6) 600 Larder/ ApplianceBack & Shelf Pack
9
Styles vary by rangeFeature Units Decor Glass W all EndsComments
500 Console UnitTraditional(TCU5)
Supplied rigid.
Supplied rigid.600 Console UnitTraditional(TCU6)
(WSU) Wall End Wing Unit
(BSU) Base End Wing Unit
(CAN) 600 Traditional Canopy
(CAN) 800 / 900 / 1000 Traditional Canopy
(CAN) 600 Bread Bin Canopy
Recommended Appliance-600 Canopy Motor
Sometimes supplied rigid.Left or right handed in some ranges.
Recommended Appliance-600 Canopy Motor
Recommended Appliance-600 Canopy Motor
Decor Glass Wall EndUniversal(TCU6)
Decor Left Hand(DDPGL)
Glass Dresser End
Decor Right Hand(DDPGR)
Glass Dresser End
Sometimes supplied rigid.Left or right handed in some ranges.
Decor Ends
735 x 337mm Wall Decor End
795 mm Wall Decor End x 337
1283 x 337mm Dresser Decor End
890 mm Base Decor End x 600
2400 x 600mm Tall Decor End
Pilasters
Tall Units Handles Additional Items AndRecommended Appliances
End P anels
600 Larders & Appliance Housings
Ordered Item: Component Received:
3
1
2
1
Mid HeightAppliance HousingType 'EM’
Mid HeightAppliance HousingType 'DM’
Mid HeightAppliance HousingType 'CM’
Mid HeightAppliance HousingType 'FM’
Mid HeightAppliance HousingType 'GM’
2Mid HeightAppliance HousingType 'BM’
600 Larder/ ApplianceBack & Shelf Pack
(NRLZHP6)
600 Larder/ ApplianceBack & Shelf Pack
(NRLZHP6)
600 Larder/ ApplianceBack & Shelf Pack
(NRLZHP6)
600 Larder/ ApplianceBack & Shelf Pack
(NRLZHP6)
600 Larder/ ApplianceBack & Shelf Pack
(NRLZHP6)
600 Larder/ ApplianceBack & Shelf Pack
(NRLZHP6)
600 Larder/ ApplianceBack & Shelf Pack
(NRLZHP6) 2
Integrated Dishwasher
Single OvenCompact Oven with Warming Drawer
1Mid HeightLarder UnitType 'AM’
TAE6Pair of Oven Ends*
TAE6Pair of Oven Ends*
TAE6Pair of Oven Ends*
TAE6Pair of Oven Ends*
TAE6Pair of Oven Ends*
TAE6Pair of Oven Ends*
TAE6Pair of Oven Ends*
Larder Fridge or Freezer
Compact Oven with Warming Drawer
Drawer kit KQQPD62T
Single Oven
MicrowaveCoffee Machine1 x (GRLPD6T) 600 Pan Drawer Set
Compact Oven with accessory Drawer
Assembly Instructions and fittings contained in this pack.
Fascia
(FL6) 1319 x 596 Door Fascia
(FAH1) 290 x 596 Door Fascia
(FAH3) 1025 x 596 Door Fascia
(FA6) 600 Highline Fascia
(FBU6) 131 x 596 Filler Panel
(FAH2) 584 x 596 Door Fascia
(FBU6) 131 x 596 Filler Panel
(FA6) 600 Highline Fascia
(FAH2) 584 x 596 Door Fascia
(FPD6) 290 x 596 Drawer Fascia
(FDSP6 x2 on certain ranges)
(FBU6) 131 x 596 Filler Panel
(FPD6) 600 Pan Drawer Fascia
(FBU6) 131 x 596 Filler Panel
Shelf P ack
Compact Oven with accessory DrawerMicrowaveCoffee Machine
(WP) 795mm Wall Pilaster
(BP) 870/890mm Base Pilaster
(DP) 1283mm Dresser Pilaster
(TP) 2400(Certain Ranges)
mm Tall Pilaster
9mm Filler Kit(LQQAFK)
9mm Filler Kit(LQQAFK)
9mm Filler Kit(LQQAFK)
9mm Filler Kit(LQQAFK)
Items Packed With All Necessary Components
10 ins pira tion for your home
Other Items Available As Optional Extras (All options are not available in all ranges)
Feature Units CommentsAccessories F or F eature UnitsFrames
(ODU3) 300 Open Base &Wall Unit
(ODU5) 500 Open Base &Wall Unit
(WR) 150 Wine Rack
(WSU) 300 Wall End Wing Unit
(BSU)300 Base End Wing Unit
(BDU5) 500 Open BaseDisplay Unit
(ODF3) Frame For 300 Open Unit(735mm High)
(ODF5) (735mm High)
Frame For 500 Open Unit
(HDF5) (588mm High)
Frame For 500 Open Unit
(GRO) Gallery Rail For Open Units (1 pair)
(GRO) (1 pair)Gallery Rail For Open Units
(GRO) (1 pair)Gallery Rail For Open Units
(GRO) (1 pair)Gallery Rail For Open Units
(GRO) Gallery Rail For Open Units
(GRO) (2 pair)Gallery Rail For Dresser
(WGR) Gallery Rails For Wall End Wing
(BGR) Gallery Rails For Base End Wing
(FTW) Fretwork For Wall End Wing
(FTB) Fretwork For Base End Wing
(GS) Glass Shelf For 500 Open Shelf
(GS3) Glass Shelf For Dresser
(PRG) Plate Rack and Gallery Rail
(PRG) Plate Rack and Gallery Rail
(FHD) Herb Drawers
(FHD) Herb Drawers
Pack of 5 Spice Drawers(SD)
(WRG) Wine Rack and Gallery Rail
(WRG) Wine Rack and Gallery Rail
(F5G) 500 Glass Door
Supplied either left or right handed
(FDR) 500 Glass Door For Dresser
(WRS) Wine Rack With Scallops
(WRS) Wine Rack With Scallops
(FT3) 300 Fretwork
(FT5) 500 Fretwork
(FT5) 500 Fretwork
Gallery Rail not supplied on certain ranges
Gallery Rail not supplied on certain ranges
Handles supplied separately
Handles supplied separately
Handle supplied separately
Handle supplied separately
(FHD) Herb Drawers Handles supplied separately
Handle supplied separately(DR5) Dresser Drawer
(D T) 500 Dresser/Tambour Cabinet
C
(BGR) Plinth for Quad Unit
(BGR) Pelmet for Quad Unit
(BGR) Left-hand Cornice for Quad Unit
(BGR) Plinth for Quad Unit
(BGR) Cornice/Pelmet for Quad Unit(BSU)300 Base End Wing Unit
(BGR) Right-hand Cornice for Quad Unit
Options Packed In Separate Boxes:
11
Shown on this page are illustrations of the fittings that are used in assembling the screws are shown approximately full size. Not all of these parts will be your new kitchen. All the fittings included with each unit will be on this page. used in every kitchen. Refer to the Assembly Leaflets for actual number and Refer to the illustrations in the assembly instructions to determine which is the types of fittings required for each unit or housing. If it is necessary for you to correct list for that unit. Please study this list so as you will recognise the telephone the customer service team, please limit confusion by referring to fittings as you open the boxes. Most items are not shown full size, however, the parts by the name and reference number (i.e. Ref.154076) shown.
Section 2: Fittings Guide
Aluminium F eature Door Hinge
Jointing Plate
35mm Cover Cap (White)35mm Cover Cap (Cream)
35mm Cover Cap (Light Oak)
Wall Hanging Bracket
Wall Hanging BracketCover
Wall Hanging Plate
151701151710
151731
Tandem Dresser Drawer Side(P air)
Tandem Dresser Drawer Runner(P air)
LH-153185RH-153186
LH-153187RH-153188
152162
152155
154068
Ref .No.
Ref .No.
Ref .No.
Item Item Item
152400152401 152402
152167
152168
154004154065
154066
154024
4.5 x 45mm Carcase Screw
150101
150202
150199
4.5 x 13mm
3.5 x 13mm
150308
1503094.5 x 55mm Carcase Screw
150198
154014
4.5 x 25mm 150124
152156
152161
154041
152164
152162
RH-152247LH-152246
RH-152249LH-152248
152243
151401
4.5 x 32mm 150126
1502014.5 x 17mm
1502043.5 x 17mm
150080
DowelCam
Universal Fixing Bracket
10mm Cover Cap
Metal Shelf Support
Perma�x Block
Screw-on Half Block
154081Glass Shelf Support
154032
153158
LH-153166RH-153167
LH-153159RH-153160 153163
Tandem Drawer Bracket (P air)
LH-153180RH-153181
LH-153190RH-153191Tandem P an Drawer Box Side
153184
Soft-close Bu�er100° Hinge
Soft-close Bu�er170° Hinge
Tandem Drawer Side(P air)
Tandem Drawer Runner (P air)
170° Hinge
Aluminium F eature Door Hinge Plate
Hinge Plate
Plinth ClipLeg socket Adjustable LegAluminium F eature Door Stay
170° Hinge Arm Cover Cap
100° Hinge ArmCover Cap
Tandem F ascia Bracket
Tandem Cover (P air)
5mm Euro Screw
Mini-�x Bolt
Tandem P an Drawer Bracket
Carcase Connecting Bolt
154016
Ref .No.
Item
151999
Door\Drawer Bu�er
152171152172152173
152160
100° Hinge
153165
Tandem Gallery Rail
Pan Drawer
152170
Quad Unit 100° Hinge(unsprung)
Quad Unit Soft CloseHolderQuad Unit Soft Close
Bu�erQuad Unit Soft Close Striker Plate
154015
12 ins pira tion for your home
Some pieces of hardware could be hazardous to small children.
Keep all these items out of reach and do not leave children unattended in the assembly area.
Many of the units, particularly the double door units and tall units, are heavy and should be lifted with caution.
To reduce the risk, do not �t doors or drawers until the units have been attached to the walls.
D O N O T U S E A K N I F E T O O P E N T H E B O X E S A S T H I S M AY DA M A G E T H E C O N T E N T S .
S ection 3 : Handy Hints on Preparation and Installation
Read the plansFind and review the plans and any other drawings used to prepare your order. Pay particular attention to any units that have special features such as aluminium legs or will be positioned unusually.
PreparationBefore starting any assembly, spend some time preparing the area where the units will be fitted. To get long term use and performance from our products, make sure the kitchen is installed by a competent DIYer.To help your project run smoothly, make sure your contractor understands the measurements and dimensions before you start work.After checking that all the units you ordered have been delivered, the area should be stripped outand any obstructions such as old skirting, disused pipes, tiles etc. removed.It is not advisable to fit timber doors in newly constructed or recently plastered rooms. High moisture content in the environment may cause the doors to swell and split.Don’t store your products in and unsuitable place or on hard surfaces such as concrete etc. as they may get damaged.
ServicesIf you wish to fit or move any electric, gas or water points, now is the time to do this. Services to appliances should be to the manufacturer's specification and fitted by a qualified person. There are many Wickes Good Ideas Lea�ets to help you in this so please ask a Design Consultant inany of our Wickes stores.Our designers have created clear, easy-to-follow instructions but, if you have any difficulties, please call our customer service team who can help at any stage of the process.
•
••
•
•
•
•
•
•
•
•
Please spend 5 minutes reading this section before commencing toassemble and install your new kitchen.
CAUTION!
13
Walls and �oorMake sure all plaster work is sound particularly where the units will be attached. This is between 800 & 870mm up the wall for base units and between 2100 & 2200mm from the floor for wall units. It is important to make sure all plaster is dry before fitting units as damage may occur to the units. Floors should be sound and able to take the weight of the units and appliances.Not all walls are straight, plumb or square. However, in most cases, this can be overcome by using thin pieces of wood between the unit and the wall.
DecoratingAlthough the units will cover a large amount of the floors and walls, it may well be easier to decorate the areas of the walls, ceilings and floor that will show around the units before installation. This is particularly true of the wall and ceiling above the wall units and the space between the base and wall units. If tiles are to be fitted, it is recommended that this is done after the units and worktop have been installed.
ToolsThe following tools are necessary for assembling and installing the units:Pozidrive No2 (cross head) screwdriver; 5mm flat screwdriver; Metric tape measure; square; spirit level; electric drill with 8mm, 5mm, 3mm diameter wood drillbits and appropriate masonry drillbits; panel and jig saw; bradawl; mallet; G-clamps (minimum of two); mitre block and mitre saw; work bench or firm work surface.
BasicsProtect the finish on panels by laying them on the floor and using the packaging to prevent scratches.Do not overtighten screws and be particularly careful when using power screwdrivers.Make sure that all the parts and hardware have been enclosed, contact your supplier if there is anything missing or damaged.
First-time assemblersAll the units have been designed for easy assembly. First-time assemblers should start by assembling a small unit such as a single door base unit to familiarise themselves with the fittings. Read the assembly instructions carefully before starting assembly and complete one unit before starting the next. It is advisable to leave all of the facias, drawer boxes, plinth, cornice and worktops in a separate room whilst assembling and installing the units.
•
•
•
•
•
••
•
•
14 ins pira tion for your home
Begin in a corner. If a Corner Unit is to be fitted, assemble and position this unit in the corner.If the units are to be fitted between two corners, refer to the plan to see which corner is the starting point.The units illustrated on the right are all commonly used to start a run of units in a corner.If the kitchen does not fit up to a corner, remember to allow for End Wings or Show Ends when positioning the first unit.
Assemble the tall units and place in position
Assemble any remaining base units and place in position. Sink units should be cut as necessary for the plumbing.Find the lowest point on the floor. The legs on the unit in this position should be 140mm high plus the thickness of any flooring that will be underneath the plinth. Level the remaining base units, working away from this unit.
Read the Handy Hints pages. Check the plans for the new kitchen.
Fit any special features (such as decorative feet or replacement ends) before installing the unit and note where these units are positioned on the plans.
Try assembling a small unit to familiarise yourself with the procedure.
Level
Level
Section 4: Installation Sequence
925 x 925 Corner UnitThe shelf or carousel must be fitted before installation.To �t the carousel, it is necessary to drill a 15mm diameter hole in the top and bottom panel in the locations shown in the illustration.
Standard Base UnitThis will begin a straight run of units.
Appliance Housing, Broom Cupboard or LarderThis will begin a straight run of units.
5255
625mmX
Unit Width
Corner Base UnitFollow installation instructions with the unit for the correct position in the corner.
80mm
80mm
80mm
80mm
7.0mm
15mm15
mm
Plin
th
140m
m
Floor
FloorCovering
Top PanelDrilling
Bottom PanelDrilling
CarouselCarousel
Step 3 - Tall units Step 4 - Assemble and position the base units
Step 2 - Start in a corner
Step 1 - Get ready
15
Once the units are correctly positioned, start in a corner and fix the units to the wall and connect them together.Fix to the wall with the supplied brackets. Use plugs or other suitable fixings of the correct type for the wall construction. Tall andappliance units in particular, must be securely fixed. If in any doubt, consult an expert.
5mm
The connecting bolts used to connect the units together can be hidden by putting them adjacent to the hinge plate, shelf or drawer runner.
Clamp the units together. Decide where to locate the connection bolts. This shows the hole being drilled behind a hinge location. Drill through with a 5mm wood drill into a piece of scrap wood. Push in the bolt and tighten the screw.
G-clampsDrill
Mark the position for drilling. Move the bracket out of the way. Drill using a bit suitable for the wall and the size of wall plug. Fit the plug. Put the bracket back in position and fit a suitable screw. Plasterboard is not strong enough to support wall or tall units so plasterboard fixings are not suitable for fixing those units but are acceptable for base units only. Tall units, especially ones with appliances, need to be very securely fixed to the wall. If necessary fit a batten to studs within the wall and then fix the unit to the batten.
Plasterboard Fixing- Not suitable for many units. See notes.
Please use suitable �xings(not supplied)
Mark a line around the room at the height for the wall hanging plates.Kitchens with Tall units: measure 64mm down from the top of the Tall Unit.Kitchens without Tall units: measure 2129mm up from the floor.If there are Dressers units, make sure there is 1259mm between the line and the top of the base units.
Centreline
Screw Slots
CentrelineScrew Slots
64 mm
DresserPosition
1259
mm
2134
mm
Alternative position above a drawer runner.
Step 5 - Connect the base units and fix to the wall
Step 6 - Mark a line for the wall hanging plates.
16 ins pira tion for your home
20mm20mm
20mm20mm
2 people are required for this
stage.
Assemble the corner wall unit. There is two types of corner wall unit. Installation is the same for both types.Fix the wall hanging plates to the wall as shown in the instructions. They are fitted to the wall 20mm in from the outside edge of the unit. Use plugs or other suitable fixings of the correct type for the wall construction. Wall hanging plates must be securely fixed to the wall. If necessary, fit a batten to studs within the wall and then fix the plates to the batten. If in any doubt, consult an expert.Hang the unit on the plates. This needs 2 people. Don't adjust the hanging bracket at this stage.
Centreline
Screw Slots
20mm20mm
Assemble the remaining wall units and accessories Hang the remaining wall units. Level the wall units by adjusting the wall hanging brackets and fit the covers.Fix the standard units together with connecting bolts. See Step 5. Feature Units and Accessories are connected with 32mm screws fitted from the adjacent units instead of connecting bolts.After fixing, tighten the units to the wall.
Fitting AccessoriesUse 32mm screws to connect the accessories to the other units. Countersinking the screws allows them to be fitted behind hinge plates, shelves or drawer runners. Use a 3mm drill to make 30mm deep pilot holes. Do not drill through both units.
3mm
4.5 x 32mm
G-clampsDrill
Plasterboard Fixing- Not suitable for wall units. See notes.
CAUTION!
625 Corner Wall
L - shaped Corner Wall
Step 7 - Assemble and fit the corner wall units.
Step 8 - Assemble and fit the remaining wall and feature units.
17
WorktopsCutting- It is recommended that the surface of the laminate is scored with a knife and then cut with a fine toothed saw. Take great care moving a worktop with a sink cut-out as the cut-out makes it weak. Sealing- All cut edges where raw chipboard is exposed on both the worktop and the carcase must be sealed with a moisture resistant sealer such as gloss paint, varnish or silicone sealant.Edging- If aluminium end caps/jointing strips are to be used, the cut edge should be sealed. The edging strip supplied with the worktop should be glued to the cut end with contact adhesive. Excess edging can be trimmed off using a metal file.
Wear a suitable dustmask when cutting MDF
Over -hang
The Cornice and Pelmet should be cut using a mitre block and saw. Follow the diagram for the correct angles. Different styles of Cornice and Pelmet are fitted in slightly different positions. See the illustration for guidance. Section A-A shows the view from the side and how the items overhang the doors. Section B-B shows the view from the front and how the items overhang the sides. Drill 5mm holes or attach half blocks 50mm in from each end and every 450mm along straight sections.
90°
The Newel Post is fixed flush at the front corners of the unit. The Pelmet must be fixed with at least enough setback to cover the ends completely.
Wall UnitUnderside
5mm
45°45° 45°
45°
45°45°
135°135°
67.5°
67.5°67.5°
90°
A
B B
A
4.5 x 32mm 4.5 x 17mm
Section A-A(Side View)
Door DoorDoor
Doo
r
Doo
r Doo
r
B-B (Front View) Section A-A(Side View)
B-B (Front View) B-B (Front View)Section A-A(Side View)
B-B(Front View)
Section A-A(Side View)
If Show Ends have been ordered, fit them now. See page 19 for details.Cut the worktops to the correct size and apply edging.Mark and cut out the holes for the sinks and hobs.Fit the worktops. At the front, the worktop is held in place by screws through the front rails. At the rear, use roundhead screws through the brackets.Fit the hob. Refer to the manufacturer’s handbook.Fit the sink. Finish plumbing.
Fit the dressers. Tile the walls and finish decorating.Mitre and fit the cornice and light pelmet.Fit Fretwork and Galleries etc.Fit remaining appliances. Refer to the manufacturer’s instructions for information. Pay particular attention to note on ventilation.
270mm
20mm
20mm
Step 9 - Fit Show Ends and Worktops.
Cornice and Pelmet
Step 10 - Fit Dressers, Cornice and Pelmet,Appliances.
Newel Post
18 ins pira tion for your home
ContinuousPlinth
==
525mm54
60
324
Trim to suitthe wall
24
384
Return Plinth
Assemble and fit the drawer boxes.Fit the shelves.Hang the doors. Refer to pages 20 and 21 for more information. Refer to information included with the appliance for information on fitting integrated appliance doors. Fit the Softclose buffers. Smaller doors need only 1 Softclose buffer with a cover cap for the other hinge. Larger doors use 2 Softclose buffers. Refer to the assembly instructions.Fit the drawer fronts.Drill the doors and drawer fronts for the handles. Refer to page 21 for more information.
Lay flooring. The flooring usually stops at the legs but will need to continue under units with decorative legs.Fit the plinth. The plinth may need to be trimmed to allow for irregularities in the floor.A return plinth is made from a section of Continuous Plinth. It will need to be notched to fit around the legs. It is fitted behind the plinth along the front. Any cut edges should be covered with the supplied edging tape using contact adhesive.On the return, fit the plinth clips the other way up to avoid clashing with the plinth clip on the front.
270mm
270mm
263mm
286mm
263mm
270mm
263mm
286mm
263mm
(if required)
Plin
th
140m
mFloor
FloorCovering
==
Edging Tape
Step 11 - Flooring and Plinth
Step 12 - Fit the Doors and Drawers.
19
Section 5: Finishing Touches - Show End Fitting
Position the unit. Clamp the Show End to the unit so that it is against the wall, draw a line parallel to the wall onto the just touching the wall. Measure the overhang at the front of Show End. Trim the Show End along the line. If desired, the the unit and subtract the amount needed to overhang the fit can be tested on a piece of the packaging before cutting door. Cut a small block of wood to this size and by placing it the Show End.
Trim tocorrectheight
5mm
5mm
The show end needs to be cut down to suit the height of the unit once it has been installed. The show end should overhang the front of the carcase and continue to the floor. The Show End is supplied 30mm deeper than the carcase to allow for scribing to the wall at the back and overhanging the door at the front. The amount of overhang depends on the thickness of the door. The bottom and back can be scribed to the floor and wall and the raw edge must be sealed with a suitable sealer. See Page 15 for hints on concealing the screws.
Over -hang
4.5 x 32mm x4/ Show End
Over -hang
4.5 x 32mm x8/ Show End
Scribeto
the wall
(Option A) (Option B)
(Option B)
Scribeto
the wall
5mm
The Show End is supplied 53mm deeper than the carcase to trimmed so that the bottom of the Show End is flush to the allow for scribing to the wall at the back and overhanging the bottom of the unit and the pelmet fitted underneath the Show door at the front. The amount of overhang depends on the End (Option B). See Page 15 for hints on concealing the thickness of the door. The bottom of the Show End can screws.either be left to enclose the pelmet (Option A) or the top
Over -hang
4.5 x 32mm x4/ Show End
Scribeto
the wall
Scribing to the Wall
Base Units and Tall Units
Wall and Dresser Units
Bottom of Wall Unit
20 ins pira tion for your home
The doors, drawer fronts and some accessories of your new kitchen are manufactured from carefully selected solid timber/veneers of the finest quality.As with most things in nature, there is a degree of variation in both colour and graining. These differences are part of the special character and beauty of wood, differences which make a wood kitchen such a desirable product.Any large differences in tone apparent when your kitchen is first unpacked will diminish over a few months as the timber mellows with exposure to daylight to give a natural uniformity.
For the best results, the doors and drawer fronts should be checked together. After unpacking, and before installing doors and drawers, it is recommend that they are placed against their respective units, in order to judge the final effect. Reposition any items to obtain the most even match.
Once you are happy with the overall effect, fit the hinges and drawer boxes. Attach doors and drawers to the cabinets taking care not to damage the lacquered surfaces. When all items are installed and you have checked the results, attach the handles.
Check one more time before drilling, place a piece of scrap wood behind the hole to prevent splintering then using a 5mm drill, carefully drill through. Fit handles taking care not to let the screwdriver slip. See inside this leaflet for more information.Please note: Any doors or drawer fronts which have been fitted with hinges or drilled for handles cannot be returned to the supplier.
Self- adhesive edging tape is available to colour match the doors. It is fitted before attaching the doors. The edge of the carcase must be clean, dry and free from dust and grease. Apply the tape carefully to the front edge. Press the tape down firmly with a clean hard roller or smooth bar to ensure good adhesion. Trim any excess with a sharp knife.
Note: It is not advisable to fit timber doors in newly constructed or recently plastered rooms. A high moisture content in the environment may cause the doors to swell and split. It is recommended that doors are stored outside the kitchen until the room has dried out thoroughly.
Section 6: Finishing Touches - Door Installation
For timber doors, drawer fronts and accessories
Please spend 5 minutes reading this section after the units have been assembled and fitted but before you start to fit the doors.
Self - Adhesive Edging Tape
Handles
Hinges and Drawers
Installation
Unpacking
21
Door AdjustmentPlease Note: The door on a single door unit may open either left or right. Before attaching hinges to the door,choose which opening is wanted and fit hinges to the appropriate side.
AC
B
A- V ertical C - HorizontalB - Lateral
Scrap wood
Loosen screw 'A' on all hinges. Adjust door and retighten screw.
Loosen screw 'B'. Adjust door and retighten screw.
Loosen screw 'B' ½ turn. Turn screw 'C' until door is positione d correctly and retighten screw 'B'.
Wall Units (Bottom of Door)
CBA
x2/hinge3.5 x 13mm
(if required)
x 2/door
CA B
B CA
Please Note: All doors and drawers are pin marked on the back for a handle. Because some Use a 5mm flat-tipped drill bit and drill into a piece of doors are reversible, they are pin marked in several places. Please decide the handle position on scrap wood to prevent splintering.all units and check all details carefully before drilling as drilled doors and drawer fronts cannot be It is recommended that the doors and drawers are fitted returned. before drilling.
Wood Drill Bit
5mm
Aluminium Feature Door
Corner Unit Hinge
Standard Hinge
Base Units (Top of Door) Drawer Fronts
Door Installation
Door and Drawer Handle Drilling
22 inspiration for your home
Important P oints
� Some doors have very thin sections in the centre or on the edges.
� The screws supplied may not be suitable for all doors.
� Note the position of shelves when positioning the rack.
� Do not overload the racks as this may damage the rack and the hinges.
x 6/Basket
x 2/Basket
Wire Door Mounted Racks (Items may be different than illustrated)
These racks are suitable for 500 or 600mm wide doors, Please read the fitting notes below.
Double Bottle Rack Single Bottle RackSpice Rack
Wicker And Wire Baskets
3.5 x 22mm
220
220
130
35
280
89
209
Section 7: Finishing Touches - Wirework
� Shallow Baskets are 100mm deep; Deep Baskets are 200mm deep.
� Baskets can be fitted to 500mm wide Highline Units, 500mm wide Drawerline Units and 500mm wide Larders.
� The following illustrations should be used as a guide only. Please check fitting before installing the baskets.
Important- This unit uses the components from the Easy Space kit. The upper two drawers are concealed drawers and assembled using the Easy Space instruction sheet. The bottom drawer is assembled the same way but the door fascia is fitted instead of the concealed drawer fascia. The drawer box is fixed to the fascia with the drawer brackets. Follow the instructions supplied with the Easy Space and fit the drawer runners and packers for a 735mm high Highline unit. The packers are fitted to the right side only.
I
I
I
x43.5 x 17mm
x2
600 Pull-out Unit
Bottom Drawer- Except for the concealed drawer fascia, use the components supplied with the Easy Space kit. The door fascia needs to be drilled for the rails and the holes for the brackets started with a bradawl in the positions shown in the illustration. The brackets are offset on one side for the packers. Fit the brackets to the fascia and assemble the drawer box using the door fascia instead of the concealed drawer fascia.
Door drilling and Bracket positions
31.549.5
10 Dia. x 12mm deep
6799
227
67 99
735mm High End PanelHighline positions
Bradawl
23
Section 8: Caring for your KitchenPlease note that although these units have been designed to give years of pleasure and satisfaction, you will help maintain the original beauty of your kitchen by following these guide lines.
Timber Doors, Trims And Timber Accessories The wood products you have purchased will resist most household chemicals including alcohol. However, any spillage which occurs should be wiped off at once and the area should be rinsed thoroughly and wiped dry! On no account should any spillage, even water, be allowed to lie on the surface.Occasional marks can, in most cases, be removed with a soft damp cloth. More persistent marks can be removed using a mild solution of water and household detergent. Once the mark is removed, the area should be wiped over with a damp cloth to remove any excess water and dried with a soft, clean cloth. On no account should solvents or an abrasive cleaner be used as permanent damage to the finish could take place.A good quality wax furniture polish can be used occasionally to emphasise the inherent beauty of the timber. Please read the manufacturer's instructions first.
Glass DoorsA non-abrasive window cleaner should be used, if the door is leaded care should be taken using cleaning solutions on the decorative leading.
Melamine, Vinyl And Foil Wrapped Mdf DoorsOccasional marks can, in most cases, be removed with a soft damp cloth. More persistent marks can be removed using a mild solution of water and household detergent. Once the mark is removed, the area should be wiped over with a damp cloth to remove any excess and dried with a soft, clean cloth. On no account should solvents or an abrasive cleaner be used as permanent damage to the finish could take place
High Gloss Doors
WorktopsAll exposed worktop edges must be sealed with a waterproof sealant to prevent water moisture penetration, which will cause the laminate to lift.Although the worktop is very hard wearing, sharp knives and objects will scratch the surface. To prevent damage, a chopping board should be used and pots and pans should be lifted and not dragged. Care should be taken not to drop any heavy objects onto the worktop as the surface may crack.The laminate surface can tolerate boiling water and hot cooking splashes but may be damaged if very hot saucepans, oven dishes, electric irons or burning cigarettes are placed on the surface. To prevent damage always use heat resistant mats and ashtrays.For cleaning, a damp soapy cloth will clean off most spills. Bleaches, scouring pads, multi-surface cleaners should not be used. Concentrated juices, corrosive liquids and food colourants should be wiped off immediately. On no account should any spillage, even water, be allowed to lie on the surface.
CarcasesDo not use polish on any surfaces, a damp cloth with soapy water will clean off most marks and spills. On no account should any spillage, even water, be allowed to lie on the surface. Bleaches, scouring pads, multi-surface cleaners should not be used.
Drawers, Runners, Doors And HingesThese should be wiped out with a damp soapy cloth and wiped dry with a soft cloth when necessary. The roller runners and hinges are lubricated and should not be cleaned with a degreasing agent as this will affect the action of the moving parts.Never lean on partially or fully open doors and drawers in order to gain access to base units. The hinges are specified to adequately support the weight of a door, plus small additional weights such as wire racks holding cloths, small jars of herbs etc. It is advised that once the kitchen has been installed you should check every six months that all screw 'B' on the hinges are tight.It is recommended not to attach a waste bin to the door, but instead use one supported by the carcase.
Wall UnitsCare should be taken not to position kettles, or any appliance which creates a large amounts of heat or steam underneath a wall unit. Excessive heat or moisture can damage the units and doors.
Temperature And HumidityAvoid excessive change in temperature and humidity as much as possible. Always try to ensure adequate ventilation when cooking and washing. Dryers, if possible, should be vented to the outside to avoid excessive humidity in the kitchen.
Use a cleaning product not containing aggressive substances like acetone, alcohol, bleach …as those components could seriously damage the surface of the door. The best would be to use soft cotton or micro fibre cloth with only water and soft soap (containing maximum 1% of liquid soap).Also smoking may cause discolouration on some finishes which is not removed by the recommended cleaning methods.
••
•
•
•
•
••
•
•
•
•
•
•
•
•
••
•
Sect
ion
9: K
ey U
nit D
imen
sion
s
Ref.1
7130
0(1
5 )Pl
ease
Note
: Eve
ry eff
ort h
as be
en m
ade t
o ins
ure t
hat th
is pr
oduc
t leav
es th
e fac
tory i
n per
fect c
ondit
ion.
Any i
tem w
hich h
as a
visibl
e defe
ct mu
st no
t be i
nstal
led an
d the
custo
mer s
ervic
e dep
artm
ent c
ontac
ted im
media
tely
735
367
307
140
735
570
1283Dresser Unit
Wall
Shelf
Unit
Base
Shelf
Un
it
300
300
400
400
Glas
s unit
500
300/5
00
Draw
erpa
ck
600 /
900
600/
600 P
ullou
t
800/1
000
800/1
000
600
Belfa
st sin
ksu
ppor
t unit
Open
disp
laywi
cker
bask
ets
500
500
Open
disp
laywi
ne ra
ck
Deco
r mou
lding
731
584
143
143
143
143
290
731
143
143
290
363
290
290
363
Wall
Dres
ser
Alum
inium
Deco
rativ
e Wall
900
500
Open
disp
laypla
te ra
ck
600
Butle
r sink
supp
ort u
nit
437
110/1
31
900
Belfa
st sin
ksu
ppor
t unit
437
Dres
ser u
nit50
0
1431127
Déco
r she
lf
450 /
500
Cook
er H
ood
600 437
600
Sing
le ov
en un
it60
0Do
uble
oven
131*
600
Extra
ctor
600
Cook
er ho
od
600
Integ
rated
hood
437
290
900
Sing
le ov
en un
it
203
44
Tall
143
with
Tamb
our
500/6
00
1283
150
Tray
363
363
600 -
605
mm12
00 -
1210
mmmm
600 -
605
mm
Pair o
fAp
plian
ces
Sing
le Ap
plian
ceSi
ngle
Appli
ance
Sing
le Ap
plian
ce
1319
731
1025290
584
1401323
1463
Type
AM
Lard
er U
nit
Type
GM
450 I
ntegr
ated
Dish
wash
er
Type
BM
In co
lumn
fridge
or fr
eeze
r
290290
290290
131
131
131
143
584
731
131
Type
CM
Comp
act O
ven
Micro
wave
Coffe
e Mac
hine
Type
EM
Sing
le ov
enCo
mpac
t Ove
n
Type
DM
Comp
act O
ven
Micro
wave
Coffe
e Mac
hine
Type
EM
Sing
le ov
enCo
mpac
t Ove
n
294
B
600
Bowf
ront
sink
supp
ort u
nit
363 363
437
Dish
wash
ers;
Built-
Unde
r Refr
igera
tion;
Was
hing M
achin
esBu
ilt-un
der A
pplia
nces
:
Spac
er pa
nel
Pan D
rawe
r2 x
Pan
Dra
wers
600 /
900 /
1200
450 /
500
600 /
900
Also
avail
able
with
draw
er
Belfa
st Si
nk
Base
fridge
or fr
eeze
r
Type
A/H
Sing
le ov
en(d
rawe
rs op
tiona
l)30
0/500
Pull
Out
Optio
n Lar
ders
Type
C/K
450 M
icrow
ave
Sing
le ov
en(d
rawe
rs op
tiona
l)
Type
D60
0 Micr
owav
eSi
ngle
oven
Type
B/J
Doub
le ov
en(d
rawe
rs op
tiona
l)
Type
EIn
colum
n
Type
F1
In co
lumn F
ridge
Type
F2
Ifrid
ge or
free
zer
n colu
mn
Type
GIn
colum
n30
0/400
500/6
00&
1000
Lard
er
Type
L45
0 App
lianc
e45
0 App
lianc
e
2198
2058
140
131*
110*
110*
131*
1319
1319
731
731
584
437
731
437
437
290
fridge
or fr
eeze
r
437
1025
1025
731
584
1025
1025
1319
1319 731
584
437
110*437 584
Tall
Pilas
terIn
colum
n Fre
ezer
Rang
e spe
cific
Forli
Lard
er
600 -
605
600 /
900 /
1200
Aven
tos F
eatur
eCa
binet
Featu
re C
abine
t
wire
bask
ets
150
Wine
Rac
k
Bow
Fron
tedSi
nk
900 A
vento
s with
Gl
ass F
eatur
eDo
or
150
Win
era
ck
150
Pul
lout
Bas
e
892
Tall W
allCa
binets
3,4,5
& 60
080
0 &10
00
731
Belfa
st Si
nkBu
tler S
ink
600 B
I-Fold
Cabin
et
600/
600 U
p & O
ver
Cabin
et
900 S
ingle
Pan D
rawe
r60
0 Sing
lePa
n Dra
wer
Integ
rated
Livin
g
363 363
584
900
Brid
ge U
nit60
0 B
ridge
Unit
600
Sho
rt W
allUn
it
400
Sma
ll Wall
Unit
584600
Sho
rt W
allUn
it
584
731731 131*
584 131*
437584 110*
437 437110*
1025584 584
10251025
584584 110*
731
143
1466
Type
A/H
Type
B/J
Type
ETy
pe F
Type
GTy
pe D
Type
C/K
Type
L
1466 731
2345
300
500
Lard
er
896
588
13/0
5/20
13
367
57030
7 367
5881025
600 C
losed
Wall
Unit
Base
/Wall
Quad
Unit
625 ‘
L' Sh
ape
Cor
ner W
all
Stan
dard
& Ta
ll Wall
Cor
ner C
abine
ts
625 I
ntern
al Cu
rved
Corn
er W
all62
5 Cor
ner
Wall
Unit
This
corne
r type
is ra
nge s
pecif
ic Th
e ove
rall s
ize re
quire
s92
5mm
x 925
mm
925
‘L' S
hape
Cor
ner B
ase
925
Sync
romo
tion
Corn
er U
nit
925 I
ntern
al Cu
rved
Corn
er B
ase
925
Inte
rnal
Cur
ved
Corn
er B
ase
R ang
e Sp
ecific
Base
Cor
ner C
abine
ts
Wal
k-In
Cor
ner P
antry
Tall C
urve
d Lar
der
925
Tall
Cor
ner C
arou
sel
Tall C
orne
r Cab
inets
900
Mon
do C
orne
r Uni
t Th
is m
ay re
quire
Dec
or E
nd P
anel
s
Ple
ase
note
: Not
all
units
are
ava
ilabl
e in
all
rang
es a
nd s
tyle
may
var
y.*1
31 a
nd 1
10 fi
ller m
ay b
e re
quire
d to
be
cut
dow
n to
sui
t var
ious
app
lianc
es
Dec
or e
nd
pane
ls