Post on 28-Mar-2018
transcript
2005 Civic 2 Door Online Reference Owner's Manual Use these links (and links throughout this manual) to navigate through this reference. For a printed owner's manual, click on authorized manuals or go to www.helminc.com. Contents
Introduction ....................................................................................................................................... i A Few Words About Safety ................................................................................................................ ii
Your Vehicle at a Glance ................................................................................................................... 3Driver and Passenger Safety ............................................................................................................ 5 Seat belts, SRS, and child protection.Instruments and Controls ................................................................................................................. 49Indicators, gauges, dashboard, and steering column.Features .............................................................................................................................................. 87Heating and cooling, audio, steering wheel, and cruise control.Before Driving.................................................................................................................................. 121Fuel, vehicle break-in, and cargo loading.Driving .............................................................................................................................................. 133Engine and transmission operation.Maintenance ..................................................................................................................................... 149Schedules, fluid checking, minor services, and vehicle storage.
Taking Care of the Unexpected ...................................................................................................... 187Flat tire, dead battery, overheating, fuses.Technical Information..................................................................................................................... 211Vehicle specifications, tires, fuels, and emissions controls.Warranty and Customer Relations (U.S. and Canada) ................................................................ 223Warranty and contact information.Authorized Manuals (U.S. only)...................................................................................................... 227How to order.Index..................................................................................................................................................... I
Service Information Summary Fluid capacities and tire pressures.
Owner's Idenfication
This Owner’s Manual should be considereda permanent part of the vehicle and shouldremain with the vehicle when it is sold.
This Owner’s Manual covers all models ofthe Civic Coupe. You may find descriptionsof equipment and features that are not onyour particular model.
The information and specifications includedin this publication were in effect at the timeof approval for printing. Honda Motor Co.,Ltd. reserves the right, however, todiscontinue or change specifications ordesign at any time without notice andwithout incurring any obligation whatsoever.
Owner’s Identif ication
POUR CLIENTS CANADIENAVIS IMPORTANT: Si vous avezbesoin d’un Manuel du Conducteuren français, veuillez demander àvotre concessionnaire decommander le numéro de pièce33S5PC40
OWNER
ADDRESS
V. I. N.
DELIVERY DATE
DEALER NAME DEALER NO.
ADDRESS
OWNER’S SIGNATURE
DEALER’S SIGNATURE
STREET
CITY STATE/PROVINCE ZIP CODE/POSTAL CODE
(Date sold to original retail purchaser)
STREET
CITY STATE/PROVINCE ZIP CODE/POSTAL CODE
Congratulations! Your selection of a 2005 Honda Civic was a wise investment.It will give you years of driving pleasure.
One of the best ways to enhance the enjoyment of your new vehicle is toread this manual. In it, you will learn how to operate its driving controls andconvenience items. Afterwards, keep this owner’s manual in your vehicle soyou can refer to it at any time.
Several warranties protect your new vehicle. Read the warranty bookletthoroughly so you understand the coverages and are aware of your rightsand responsibilities.
Maintaining your vehicle according to the schedules given in this manualhelps to keep your driving trouble-free while it preserves your investment.When your vehicle needs maintenance, keep in mind that your dealer’s staffis specially trained in servicing the many systems unique to your vehicle.Your dealer is dedicated to your satisfaction and will be pleased to answerany questions and concerns.
As you read this manual, you willfind information that is preceded bya symbol. Thisinformation is intended to help youavoid damage to your vehicle, otherproperty, or the environment.
California Proposition 65 Warning
This product containsor emits chemicals known to theState of California to cause cancerand birth defects or otherreproductive harm.
Event Data Recorders
This vehicle is equipped with one ormore recording devices commonlyreferred to as event data recordersor sensing and diagnostic modules.
Introduction
WARNING:
i
--
-
--
-
Your safety, and the safety of others,is very important. And operating thisvehicle safely is an importantresponsibility.
To help you make informeddecisions about safety, we haveprovided operating procedures andother information on labels and inthis manual. This information alertsyou to potential hazards that couldhurt you or others.
You will find this important safety information in a variety of forms,including:
on the vehicle.preceded by a safety alert symbol and one of
three signal words: , , or .
such as Important Safety Reminders or ImportantSafety Precautions.
such as Driver and Passenger Safety.how to use this vehicle correctly and safely.
This entire book is filled with important safety information please read itcarefully.
These signal words mean:
Of course, it is not practical orpossible to warn you about all thehazards associated with operating ormaintaining your vehicle. You mustuse your own good judgement.
Safety LabelsSafety Messages
Safety Headings
Safety SectionInstructions
A Few Words About Safety
DANGER WARNING CAUTION
ii
You WILL be KILLED or SERIOUSLYHURT if you don’t follow instructions.
You CAN be KILLED or SERIOUSLYHURT if you don’t follow instructions.
You CAN be HURT if you don’t followinstructions.
Your Vehicle at a GlanceY
ourV
ehicleata
Glance
3
POWER WINDOWSWITCHES
HOOD RELEASEHANDLE
HEATING/COOLING CONTROLS
A/T model is shown.
AUTOMATIC TRANSMISSION
MANUAL TRANSMISSION
GAUGES
POWERDOOR LOCKMASTERSWITCH
INSTRUMENT PANEL INDICATORS (P. 51)(P. 58) (P. 9, 22)
FRONT AIRBAGS
(P. 69)
(P. 78)
FUEL FILL DOOR RELEASEHANDLE(P. 123)TRUNK RELEASE HANDLE(P. 70)
(P. 124)(P. 138)
(P. 136)
(P. 88)
Your Vehicle at a Glance
4
HEADLIGHTS/TURN SIGNALS
MIRROR CONTROLS CRUISE CONTROL BUTTONS
REAR WINDOWDEFOGGER
WINDSHIELD WIPERS/WASHERS
AUDIO SYSTEM
STEERING WHEEL ADJUSTMENT
HAZARD WARNING BUTTON
MOONROOF SWITCH(P. 79)
CRUISE CONTROLMASTER BUTTON(P. 117)
(P. 80)
(P. 62)
(P. 61)
(P. 64)
(P. 92)CLOCK(P. 115)
(P. 64)
ACCESSORY POWER SOCKET(P. 85)
(P. 117)(P. 65)
-
This section gives you importantinformation about how to protectyourself and your passengers. Itshows you how to use seat belts. Itexplains how your airbags work. Andit tells you how to properly restraininfants and children in your vehicle.
.........Important Safety Precautions . 6.......Your Vehicle’s Safety Features . 7
.........Protecting Adults and Teens . 11.....1. Close and Lock the Doors . 11
...........2. Adjust the Front Seats . 11............3. Adjust the Seat-Backs . 12
...4. Adjust the Head Restraints . 135. Fasten and Position the Seat
.....................................Belts . 14
6. Maintain a Proper Sitting................................Position . 15
.....Advice for Pregnant Women . 16...Additional Safety Precautions . 16
Additional Information About.......................Your Seat Belts . 18
..Seat Belt System Components . 18......................Lap/Shoulder Belt . 18
Automatic Seat Belt...............................Tensioners . 19
...............Seat Belt Maintenance . 19Additional Information About
...........................Your Airbags . 21......Airbag System Components . 21
How Your Front Airbags.........................................Work . 22
...How Your Side Airbags Work . 24..How the SRS Indicator Works . 25
How the Side Airbag Off......................Indicator Works . 26
.............................Airbag Service . 26...Additional Safety Precautions . 26
Protecting Children General................................Guidelines . 27
All Children Must Be...............................Restrained . 27
All Children Should Sit in a.................................Back Seat . 28
The Passenger’s Front Airbag................Poses Serious Risks . 28
If You Must Drive with Several...................................Children . 30
If a Child Requires Close..................................Attention . 30
...Additional Safety Precautions . 30Protecting Infants and Small
...................................Children . 32.......................Protecting Infants . 32
.........Protecting Small Children . 33.....................Selecting a Child Seat . 34....................Installing a Child Seat . 35
...............................With LATCH . 36..........................With a Seat Belt . 38
..............................With a Tether . 40...........Protecting Larger Children . 41
...............Checking Seat Belt Fit . 41..................Using a Booster Seat . 42
..When Can a Child Sit in Front . 43...Additional Safety Precautions . 44
.............Carbon Monoxide Hazard . 45...................................Safety Labels . 46
Driver and Passenger SafetyD
riverand
Passenger
Safety
5
-
You’ll find many safetyrecommendations throughout thissection, and throughout this manual.The recommendations on this pageare the ones we consider to be themost important.
A seat belt is your best protection inall types of collisions. Airbags aredesigned to supplement seat belts,not replace them. So even thoughyour vehicle is equipped with airbags,make sure you and your passengersalways wear your seat belts, andwear them properly (see page ).
Alcohol and driving don’t mix. Evenone drink can reduce your ability torespond to changing conditions, andyour reaction time gets worse with
every additional drink. So don’t drinkand drive, and don’t let your friendsdrink and drive, either.
While airbags can save lives, theycan cause serious or fatal injuries tooccupants who sit too close to them,or are not properly restrained.Infants, young children, and shortadults are at the greatest risk. Besure to follow all instructions andwarnings in this manual.
Children age 12 and under shouldride properly restrained in a backseat, not the front seat. Infants andsmall children should be restrainedin a child seat. Larger childrenshould use a booster seat and a lap/shoulder belt until they can use thebelt properly without a booster seat(see pages ).
Excessive speed is a major factor incrash injuries and deaths. Generally,the higher the speed, the greater therisk, but serious injuries can alsooccur at lower speeds. Never drivefaster than is safe for currentconditions, regardless of themaximum speed posted.
Having a tire blowout or amechanical failure can be extremelyhazardous. To reduce the possibilityof such problems, check your tirepressures and condition frequently,and perform all regularly scheduledmaintenance (see page ).
14
4427
152
Important Safety Precautions
Always Wear Your Seat Belt
Don’t Drink and Drive
Be Aware of Airbag Hazards
Restrain All Children
Control Your Speed
Keep Your Vehicle in SafeCondition
6
Your vehicle is equipped with manyfeatures that work together toprotect you and your passengersduring a crash.
Some features do not require anyaction on your part. These include astrong steel framework that forms asafety cage around the passengercompartment; front and rear crushzones; a collapsible steering column;and tensioners that tighten the frontseat belts in a crash.
However, you and your passengerscan’t take full advantage of thesefeatures unless you remain sitting ina proper position and
. In fact, some safetyfeatures can contribute to injuries ifthey are not used properly.
The following pages explain how youcan take an active role in protectingyourself and your passengers.
Your Vehicle’s Safety Features
always wearyour seat belts
Driver
andP
assengerSafety
7
(7)(11)
(9)
(2)
(8)
(6)(4)(3)(1)
(7)
(5)
(2)
(10)(8)
(1) Safety Cage(2) Crush Zone(3) Seats and Seat-Backs(4) Head Restraints(5) Collapsible Steering Column(6) Seat Belts(7) Front Airbags(8) Side Airbags (Optional)(9) Front Seat Belt Tensioners(10) Door Locks(11) Seat Belt Buckle Tensioners
Your vehicle is equipped with seatbelts in all seating positions.
Your seat belt system also includesan indicator on the instrument panelto remind you and your passengersto fasten your seat belts.
Seat belts are the single mosteffective safety device for adults andlarger children. (Infants and smallerchildren must be properly restrainedin child seats.)
Not wearing a seat belt properlyincreases the chance of seriousinjury or death in a crash, eventhough your vehicle has airbags.
In addition, most states and allCanadian provinces require you towear seat belts.
When properly worn, seat belts:
Keep you connected to the vehicleso you can take advantage of thevehicle’s built-in safety features.
Help protect you in almost everytype of crash, including frontal,side, and rear impacts androllovers.
Help keep you from being thrownagainst the inside of the vehicleand against other occupants.
Keep you from being thrown outof the vehicle.
Help keep you in a good positionshould the airbags ever deploy. Agood position reduces the risk ofinjury from an inflating airbag andallows you to get the bestadvantage from the airbag.
Of course, seat belts cannotcompletely protect you in everycrash. But in most cases, seat beltscan reduce your risk of seriousinjury.
Always wear your seat belt, andmake sure you wear it properly.
Your Vehicle’s Safety Features
Seat Belts
Why Wear Seat Belts
What You Should Do:
8
Not wearing a seat belt properlyincreases the chance of seriousinjury or death in a crash, eventhough your vehicle has airbags.
Be sure you and yourpassengers always wear seatbelts and wear them properly.
Your vehicle has a SupplementalRestraint System (SRS) with frontairbags to help protect the heads andchests of the driver and a front seatpassenger during a moderate tosevere frontal collision (see page
for more information on howyour front airbags work).
Your vehicle also has side airbags tohelp protect the upper torso of thedriver or a front seat passengerduring a moderate to severe sideimpact (see page for moreinformation on how your side airbagswork).
They are designed to supplementthe seat belts.
The most important things you needto know about your airbags are:
To dotheir job, airbags must inflate withtremendous force. So whileairbags help save lives, they cancause minor injuries or moreserious or even fatal injuries ifoccupants are not properlyrestrained or sitting properly.
22 24
Only on models equipped with sideairbags
CONTINUED
Airbags do not replace seat belts.
Airbags offer no protection in rearimpacts, or minor frontal or sidecollisions.
Airbags can pose hazards.
Airbags
Your Vehicle’s Safety FeaturesD
riverand
Passenger
Safety
9
Always wearyour seat belt properly, and situpright and as far back from thesteering wheel as possible whileallowing full control of the vehicle. Afront passenger should move theirseat as far back from the dashboardas possible.
The rest of this section gives moredetailed information about how youcan maximize your safety.
Remember, however, that no safetysystem can prevent all injuries ordeaths that can occur in a severecrash, even when seat belts areproperly worn and the airbags deploy.
Your Vehicle’s Safety Features
What you should do:
10
-
After everyone has entered thevehicle, be sure the doors are closedand locked.
Adjust the driver’s seat as far to therear as possible while allowing you tomaintain full control of the vehicle.Have a front passenger adjust theirseat as far to the rear as possible.
The following pages provideinstructions on how to properlyprotect the driver, adult passengers,and teenage children who are largeenough and mature enough to driveor ride in the front.
See pages for importantguidelines on how to properlyprotect infants, small children, andlarger children who ride in yourvehicle.
Locking the doors reduces thechance of someone being thrown outof the vehicle during a crash, and ithelps prevent passengers fromaccidentally opening a door andfalling out.
Locking the doors also helps preventan outsider from unexpectedlyopening a door when you come to astop.
See page for how to lock thedoors.
69
27 31
CONTINUED
Protecting Adults and Teens
Adjust the Front SeatsClose and Lock the DoorsIntroduction 1. 2.
Driver
andP
assengerSafety
11
If you sit too close to the steeringwheel or dashboard, you can beseriously injured by an inflating frontairbag, or by striking the steeringwheel or dashboard.
The National Highway Traffic SafetyAdministration and TransportCanada recommend that driversallow at least 10 inches (25 cm)between the center of the steeringwheel and the chest.
If you cannot get far enough awayfrom the steering wheel and stillreach the controls, we recommendthat you investigate whether sometype of adaptive equipment may help.
Once your seat is adjusted correctly,rock it back and forth to make surethe seat is locked in position.
See page for how to adjust thefront seats.
Adjust the driver’s seat-back to acomfortable, upright position,leaving ample space between yourchest and the airbag cover in thecenter of the steering wheel.
Passengers with adjustable seat-backs should also adjust their seat-back to a comfortable, uprightposition.
73
Protecting Adults and Teens
Adjust the Seat-Backs3.
12
Sitting too close to a frontairbag can result in seriousinjury or death if the frontairbags inflate.
Always sit as far back from thefront airbags as possible.
Properly adjusted head restraintswill help protect occupants fromwhiplash and other crash injuries.
See page for how to adjust thehead restraints.
Adjust the driver’s head restraint sothe back of your head rests againstthe center of the restraint.
Have passengers with adjustablehead restraints adjust their restraintsproperly as well. Taller personsshould adjust their restraint as highas possible.
Reclining a seat-back so that theshoulder part of the belt no longerrests against the occupant’s chestreduces the protective capability ofthe belt. It also increases the chanceof sliding under the belt in a crashand being seriously injured. Thefarther a seat-back is reclined, thegreater the risk of injury.
See page for how to adjust theseat-backs.
75
73
CONTINUED
Protecting Adults and Teens
Adjust the Head Restraints4.
Driver
andP
assengerSafety
13
Improperly positioning headrestraints reduces theireffectiveness and you can beseriously injured in a crash.
Make sure head restraints arein place and positioned properlybefore driving.
Reclining the seat-back too farcan result in serious injury ordeath in a crash.
Adjust the seat-back to anupright position, and sit wellback in the seat.
This spreads the forces of a crashover the strongest bones in yourupper body.Insert the latch plate into the buckle,
then tug on the belt to make sure thebelt is securely latched. Check thatthe belt is not twisted, because atwisted belt can cause seriousinjuries in a crash.
Position the lap part of the belt aslow as possible across your hips,then pull up on the shoulder part ofthe belt so the lap part fits snugly.This lets your strong pelvic bonestake the force of a crash and reducesthe chance of internal injuries.
If necessary, pull up on the belt againto remove any slack, then check thatthe belt rests across the center ofyour chest and over your shoulder.
Protecting Adults and Teens
Fasten and Position the SeatBelts
5.
14
Improperly positioning the seatbelts can cause serious injuryor death in a crash.
Make sure all seat belts areproperly positioned beforedriving.
After all occupants have adjustedtheir seats and put on seat belts, it isvery important that they continue tosit upright, well back in their seats,with their feet on the floor, until thevehicle is parked and the engine isoff.
Sitting improperly can increase thechance of injury during a crash. Forexample, if an occupant slouches,lies down, turns sideways, sitsforward, leans forward or sideways,or puts one or both feet up, thechance of injury during a crash isgreatly increased.
In addition, an occupant who is out ofposition in the front seat can beseriously or fatally injured in a crashby striking interior parts of thevehicle or being struck by aninflating front airbag.
See page for additionalinformation about your seat beltsand how to take care of them.
This could causevery serious injuries in a crash.
If a seat belt does not seem to workproperly, it may not protect theoccupant in a crash.
Using a seatbelt that is not working properly canresult in serious injury or death.Have your dealer check the belt assoon as possible.
18
Protecting Adults and Teens
Maintain a Proper SittingPosition
6.Never place the shoulder portion of alap/shoulder belt under your arm orbehind your back.
No one should sit in a seat with aninoperative seat belt.
Driver
andP
assengerSafety
15
Sitting improperly or out ofposition can result in seriousinjury or death in a crash.
Always sit upright, well back inthe seat, with your feet on thefloor.
If you are pregnant, the best way toprotect yourself and your unbornchild when driving or riding in avehicle is to always wear a seat belt,and keep the lap part of the belt aslow as possible across the hips.
When driving, remember to situpright and adjust the seat as farback as possible while allowing fullcontrol of the vehicle. When ridingas a front passenger, adjust the seatas far back as possible.
This will reduce the risk of injuriesto both you and your unborn childthat can be caused by a crash or aninflating front airbag.
Each time you have a checkup, askyour doctor if it’s okay for you todrive.
If they do, theycould be very seriously injured in acrash.
Devices intended to improveoccupant comfort or reposition theshoulder part of a seat belt canreduce the protective capability ofthe belt and increase the chance ofserious injury in a crash.
Carrying hard or sharpobjects on your lap, or driving witha pipe or other sharp object inyour mouth, can result in injuriesif your front airbag inflates.
Protecting Adults and Teens
Advice for Pregnant Women Additional Safety PrecautionsTwo people should never use thesame seat belt.
Do not put any accessories on seatbelts.
Do not place hard or sharp objectsbetween yourself and a frontairbag.
16
If yourhands or arms are close to anairbag cover, they could be injuredif the airbag inflates.
Objects onthe covers marked ‘‘SRS AIRBAG’’could interfere with the properoperation of the airbags or bepropelled inside the vehicle andhurt someone if the airbags inflate.
If a side airbag inflates, acup holder or other hard objectattached on or near the door couldbe propelled inside the vehicle andhurt someone.
Protecting Adults and Teens
Keep your hands and arms awayfrom the airbag covers.
Do not attach or place objects onthe front airbag covers.
On models with side airbags, donot attach hard objects on or neara door.
Driver
andP
assengerSafety
17
Your seat belt system includes lap/shoulder belts in all five seatingpositions. The front seat belts arealso equipped with automatic seatbelt tensioners.
The lap and shoulder belt goes overyour shoulder, across your chest,and across your hips.
To fasten the belt, insert the latchplate into the buckle, then tug on thebelt to make sure the buckle islatched (see page for how toproperly position the belt).
To unlock the belt, push the redPRESS button on the buckle. Guidethe belt across your body so that itretracts completely. After exiting thevehicle, be sure the belt is out of theway and will not get closed in thedoor.
All seat belts have an emergencylocking retractor. In normal driving,the retractor lets you move freely inyour seat while it keeps sometension on the belt. During a collisionor sudden stop, the retractorautomatically locks the belt to helprestrain your body.
If the shoulder part of the belt ispulled all the way out, the lockingmechanism will activate. The beltwill retract, but it will not allow thepassenger to move freely.
The seat belts in all positions exceptthe driver’s have an additionallocking mechanism that must beactivated to secure a child seat (seepage ).
The seat belt systemincludes an indicator on the
instrument panel and a beeper toremind you to fasten your seat belt.
If you turn the ignition switch to ON(II) before fastening your seat belt,the beeper will sound, and theindicator will flash. If you do notfasten your seat belt before thebeeper stops, the indicator will stopflashing but remain on.
If you continue driving withoutfastening your seat belt, the beeperwill sound and the indicator will flashagain at regular intervals.
To deactivate the lockingmechanism, unlatch the buckle andlet the seat belt fully retract. Torefasten the seat belt, pull it out onlyas far as needed.
14
38
Seat Belt System Components Lap/Shoulder Belt
Additional Information About Your Seat Belts
18
For added protection, the front seatbelts are equipped with automaticseat belt tensioners. When activated,the tensioners immediately tightenthe belts to help hold the driver anda front passenger in place.
The tensioners are designed toactivate primarily in frontal collisions,and they should activate in anycollision severe enough to causefront-airbag inflation.
The tensioners can also be activatedduring a collision in which the frontairbags do not deploy. In this case,the airbags would not be needed, butthe additional restraint could behelpful.
When the tensioners are activated,the seat belts will remain tight untilthey are unbuckled in the normalmanner.
For safety, you should check thecondition of your seat belts regularly.
Pull each belt out fully and look forfrays, cuts, burns, and wear. Checkthat the latches work smoothly andthe belts retract easily. Any belt thatis not in good condition or workingproperly will not provide goodprotection and should be replaced assoon as possible.
Honda provides a lifetime warrantyon seat belts for U.S. models. Seeyourbooklet for details.
Honda Warranty Information
CONTINUED
Additional Information About Your Seat Belts
Automatic Seat Belt Tensioners Seat Belt Maintenance
Driver
andP
assengerSafety
19
If a seat belt is worn during a crash,it must be replaced by your dealer. Abelt that has been worn during acrash may not provide the same levelof protection in a subsequent crash.
The dealer should also inspect theanchors for damage and replacethem if needed. If the automatic seatbelt tensioners activate during acrash, they must be replaced.
For information on how to clean yourseat belts, see page .174
Additional Information About Your Seat Belts
20
Not checking or maintainingseat belts can result in seriousinjury or death if the seat beltsdo not work properly whenneeded.
Check your seat belts regularlyand have any problemcorrected as soon as possible.
Your airbag system includes:
Automatic front seat belttensioners (see page ).
In models with side airbags, anindicator on the instrument panelthat alerts you that the passenger’sside airbag has been turned off(see page ).
Emergency backup power in caseyour vehicle’s electrical system isdisconnected in a crash.
Two SRS (Supplemental RestraintSystem) front airbags. The driver’sairbag is stored in the center ofthe steering wheel; the frontpassenger’s airbag is stored in thedashboard. Both are marked ‘‘SRSAIRBAG’’ (see page ).
In models with side airbags, onefor the driver and one for a frontpassenger. The airbags are storedin the outer edges of the seat-backs. Both are marked ‘‘SIDEAIRBAG’’ (see page ).
Sensors that can detect amoderate to severe front impact,or side impact in models with sideairbags.
In models with side airbags,sensors that can detect whether asmall person or child is in thepassenger’s side airbag path andautomatically turn the airbag off(see page ).
An indicator on the instrumentpanel that alerts you to a possibleproblem with your airbags,sensors, or seat belt tensioners(see page ).
A sophisticated electronic systemthat continually monitors andrecords information about thesensors, the control unit, theairbag activators, the seat belttensioners, and driver and frontpassenger seat belt use when theignition is ON (II).
22
24
19
26
25
25
Airbag System Components
Additional Information About Your AirbagsD
riverand
Passenger
Safety
21
After inflating, the front airbagsimmediately deflate, so they won’tinterfere with the driver’s visibility,or the ability to steer or operateother controls.
The total time for inflation anddeflation is one-tenth of a second, sofast that most occupants are notaware that the airbags deployed untilthey see them lying in their laps.
During a frontal crash, your seat beltrestrains your lower body and torso,and the front airbag helps protectyour head and chest.
Although both airbags normallyinflate within split second of eachother, it is possible for only oneairbag to deploy.
This can happen if the severity of acollision is at the margin, orthreshold, that determines whetheror not the airbags will deploy. Insuch cases, the seat belt will providesufficient protection, and thesupplemental protection offered bythe airbag would be minimal.
If you ever have a moderate tosevere frontal collision, sensors willdetect the vehicle’s rapiddeceleration.
If the rate of deceleration is highenough, the control unit will instantlyinflate the driver’s and frontpassenger’s airbags, at the time andwith the force needed.
Additional Information About Your Airbags
How Your Front Airbags Work
22
Your front airbags are also dual-threshold airbags. Airbags with thisfeature have two deploymentthresholds that depend on whetheror not the occupant is wearing a seatbelt.
If the occupant’s belt is ,the airbag will deploy at a slightlylower threshold, because theoccupant would need extraprotection.
If the occupant’s belt , theairbag will inflate at a slightly higherthreshold, when the airbag would beneeded to supplement the protectionprovided by the seat belt.
Your front airbags are dual-stageairbags. This means they have twoinflation stages that can be ignitedsequentially or simultaneously,depending on crash severity.
In a crash, both stageswill ignite simultaneously to providethe quickest and greatest protection.
In a crash, one stage willignite first, then the second stagewill ignite a split second later. Thisprovides longer airbag inflation timewith a little less force.
After a crash, you may see whatlooks like smoke. This is actuallypowder from the airbag’s surface.Although the powder is not harmful,people with respiratory problemsmay experience some temporarydiscomfort. If this occurs, get out ofthe vehicle as soon as it is safe to doso.
Additional Information About Your Airbags
Dual-Threshold Airbags
not latched
is latched
Dual-Stage Airbags
more severe
less severe
Driver
andP
assengerSafety
23
Only one airbag will deploy during aside impact. If the impact is on thepassenger’s side, the passenger’sside airbag will deploy even if thereis no passenger.
To get the best protection from theside airbags, front seat occupantsshould wear their seat belts and situpright and well back in their seats.
If you ever have a moderate tosevere side impact, sensors willdetect rapid deceleration and signalthe control unit to instantly inflateeither the driver’s or the passenger’sside airbag.
To reduce the risk of injury from aninflating side airbag, your vehicle hasan automatic cutoff system for thepassenger’s side airbag.
Although Honda does not encouragechildren to ride in front, this systemis designed to shut off the sideairbag if a child leans into the sideairbag’s path.
The side airbag may also shut off if ashort adult leans sideways, or alarger adult slouches and leanssideways into the airbag’sdeployment path.
Objects placed on the frontpassenger seat can also cause theside airbag to be shut off.
On models equippedHow Your Side Airbags Work
Additional Information About Your Airbags
Side Airbag Cutoff System
24
If the Side Airbag Off Indicatorcomes on (see page ), have thepassenger sit upright. Once thepassenger is out of the airbag’sdeployment path, the system willturn the airbag back on, and theindicator will go out.
There will be some delay betweenthe moment the passenger movesinto or out of the airbag deploymentpath and when the indicator comeson or goes off.
A front seat passenger should notuse a cushion or other object as abackrest. It may prevent the cutoffsystem from working properly.
The SRS indicator alertsyou to a potential problem
with your airbags or seat belttensioners.
When you turn the ignition switch toON (II), this indicator comes onbriefly then goes off. This tells youthe system is working properly.
If the indicator comes on at anyother time, or does not come on at all,you should have the system checkedby your dealer. For example:
If the indicator stays on after theengine starts.
If the SRS indicator does not comeon after you turn the ignitionswitch to ON (II).
If the indicator comes on orflashes on and off while you drive.
If you see any of these indications,the airbags and seat belt tensionersmay not work properly when youneed them.
26
Additional Information About Your Airbags
How the SRS Indicator Works
Driver
andP
assengerSafety
25
Ignoring the SRS indicator canresult in serious injury or deathif the airbag systems ortensioners do not work properly.
Have your vehicle checked by adealer as soon as possible ifthe SRS indicator alerts you toa possible problem.
This indicator alerts youthat the passenger’s side
airbag has been automatically shutoff. It does mean there is aproblem with your side airbags.
When you turn the ignition switch toON (II), the indicator should comeon briefly and go off (see page ).If it doesn’t come on, stays on, orcomes on while driving without apassenger in the front seat, have thesystem checked.
Your airbag systems are virtuallymaintenance free, and there are noparts you can safely service.However, you must have yourvehicle serviced if:
Any airbagthat has deployed must bereplaced along with the controlunit and other related parts. If afront airbag inflates, the seat belttensioners must also be replaced.
Do not try to remove or replaceany airbag by yourself. This mustbe done by your dealer or aknowledgeable body shop.
Take your vehicle to anauthorized dealer as soon aspossible. If you ignore thisindication, your airbags may notoperate properly.
Together, airbags andseat belts provide the bestprotection.
Tampering could causethe airbags to deploy, possiblycausing very serious injury.
If water or another liquidsoaks into a seat-back, it canprevent the side airbag cutoffsystem from working properly.
Improperly replacingor covering front seat-back coverscan prevent your side airbags frominflating during a side impact.
54
In models with side airbags
How the Side Airbag OffIndicator Works
Additional Safety PrecautionsAirbag Service
notAn airbag ever inflates.
The SRS indicator alerts you to aproblem.
Do not attempt to deactivate yourairbags.
Do not tamper with airbagcomponents or wiring for anyreason.
Do not expose the front seat-backsto liquid.
Do not cover or replace front seat-back covers without consultingyour dealer.
Additional Information About Your Airbags
26
-
--
CONTINUED
Children depend on adults to protectthem. However, despite their bestintentions, many adults do not knowhow to protect childpassengers.
If you have children, or ever need todrive with a child in your vehicle, besure to read this section. It beginswith important general guidelines,then presents special information forinfants, small children, and largerchildren.
Each year, many children are injuredor killed in vehicle crashes becausethey are either unrestrained or notproperly restrained. In fact, vehicleaccidents are the number one causeof the death of children ages 12 andunder.
To reduce the number of childdeaths and injuries, every state andCanadian province requires thatinfants and children be properlyrestrained when they ride in avehicle.
(see pages ).(see pages ).44
403241
properly
Protecting Children General Guidelines
All Children Must Be Restrained
Infants and small children must berestrained in an approved child seatthat is properly secured to thevehicle
Larger children must be restrainedwith a lap/shoulder belt and ride ona booster seat until the seat belt f itsthem properly
Driver
andP
assengerSafety
27
Children who are unrestrainedor improperly restrained can beseriously injured or killed in acrash.
Any child too small for a seatbelt should be properlyrestrained in a child seat. Alarger child should be properlyrestrained with a seat belt anduse a booster seat if necessary.
-
Whenever possible,larger children should sit in the backseat, on a booster seat if needed, andbe properly restrained with a seatbelt (see page for importantinformation about protecting largerchildren).
According to accident statistics,children of all ages and sizes aresafer when they are restrained in aback seat. The National HighwayTraffic Safety Administration andTransport Canada recommend thatall children age 12 and under beproperly restrained in a back seat.
Children who ride in back are lesslikely to be injured by strikinginterior vehicle parts during acollision or hard braking. Also,children cannot be injured by aninflating front airbag when they ridein the back.
Front airbags have been designed tohelp protect adults in a moderate tosevere frontal collision. To do thisthe passenger’s front airbag is quitelarge, and it can inflate with enoughforce to cause very serious injuries.
Ifthe airbag inflates, it can hit the backof the child seat with enough forceto kill or very seriously injure aninfant.
If the vehicle seat istoo far forward, or the child’s head isthrown forward during a collision, aninflating front airbag can strike thechild with enough force to kill orvery seriously injure a small child.
41
Children who have outgrown childseats are also at risk of being injuredor killed by an inflating passenger’sfront airbag.
Never put a rear-facing child seat inthe front seat of a vehicle equippedwith a passenger’s front airbag.
Placing a forward-facing child seat inthe front seat of a vehicle equippedwith a passenger’s front airbag canbe hazardous.
Infants
Small Children
Larger Children
Protecting Children General Guidelines
All Children Should Sit in a BackSeat
The Passenger’s Front AirbagPoses Serious Risks
28
-
To remind you of the passenger’sfront airbag hazards, and thatchildren must be properly restrainedin a back seat, your vehicle haswarning labels on the dashboard(U.S. models) and on the front visors.Please read and follow theinstructions on these labels.
U.S. Models
Canadian Models
Protecting Children General GuidelinesD
riverand
Passenger
Safety
29
SUN VISOR
SUN VISOR
DASHBOARD
-
Many parents say they prefer to putan infant or small child in the frontpassenger seat so they can watch thechild, or because the child requiresattention.
Placing a child in the front seatexposes the child to hazards in afrontal collision, and paying closeattention to a child distracts thedriver from the important tasks ofdriving, placing both of you at risk.
Your vehicle has a back seat wherechildren can be properly restrained.If you ever have to carry a group ofchildren, and a child must ride infront:
Place the largest child in the frontseat, provided the child is largeenough to wear the lap/shoulderbelt properly (see page ).
Move the vehicle seat as far to therear as possible (see page ).
Have the child sit upright and wellback in the seat (see page ).
Make sure the seat belt is properlypositioned and secured (see page
).
If a child requires close physicalattention or frequent visual contact,we strongly recommend that anotheradult ride with the child in a backseat. The back seat is far safer for achild than the front.
If you are not wearing aseat belt in a crash, you could bethrown forward and crush thechild against the dashboard or aseat-back. If you are wearing aseat belt, the child can be tornfrom your arms and be seriouslyhurt or killed.
During a crash, thebelt could press deep into the childand cause serious or fatal injuries.
If they do, theycould be very seriously injured in acrash.
41
73
15
14
If You Must Drive with SeveralChildren
If a Child Requires CloseAttention
Additional Safety Precautions
Protecting Children General Guidelines
Never hold an infant or child onyour lap.
Never put a seat belt over yourselfand a child.
Never let two children use thesame seat belt.
30
-
Leaving children withoutadult supervision is illegal in moststates and Canadian provinces,and can be very hazardous.
For example, infants and smallchildren left in a vehicle on a hotday can die from heatstroke. Achild left alone with the key in theignition switch can accidentally setthe vehicle in motion, possiblyinjuring themselves or others.
Children who play in vehicles canaccidentally get trapped inside.Teach your children not to play inor around vehicles. Know how tooperate the emergency trunkopener and decide if your childrenshould be shown how to use thisfeature (see page ).
Even very youngchildren learn how to unlockvehicle doors, turn on the ignitionswitch, and open the trunk, whichcan lead to accidental injury ordeath.
70
Protecting Children General Guidelines
Do not leave children alone in avehicle.
Lock both doors and the trunkwhen your vehicle is not in use.
Keep vehicle keys and remotetransmitters out of the reach ofchildren.
Driver
andP
assengerSafety
31
When properly installed, a rear-facing child seat may prevent thedriver or a front passenger frommoving the seat as far back asrecommended, or from locking theseat-back in the desired position.
An infant must be properlyrestrained in a rear-facing, recliningchild seat until the child reaches theseat maker’s weight or height limitfor the seat and the child is at leastone year old.
Only a rear-facing child seat providesproper support for a baby’s head,neck, and back.
Two types of seats may be used: aseat designed exclusively for infants,or a convertible seat used in the rear-facing, reclining mode.
If placedfacing forward, an infant could bevery seriously injured during afrontal collision.
A rear-facing child seat can be placedin any seating position in the backseat, but not in the front.
If the passenger’s front airbaginflates, it can hit the back of thechild seat with enough force to kill orseriously injure an infant.
Protecting Infants
Protecting Infants and Small Children
Child Seat Type
Do not put a rear-facing child seat ina forward-facing position.
Rear-facing Child Seat Placement
Never put arear-facing child seat in the frontseat.
32
We strongly recommend placing aforward-facing child seat in a backseat, not the front.
If the vehicle seat is toofar forward, or the child’s head isthrown forward during a collision, aninflating airbag can strike the childwith enough force to cause veryserious or fatal injuries.
A child who is at least one year old,and who fits within the child seatmaker’s weight and height limits,should be restrained in a forward-facing, upright child seat.
Of the different seats available, werecommend those that have a five-point harness system as shown.
In either situation, we stronglyrecommend that you install the childseat directly behind the frontpassenger’s seat, move the seat asfar forward as needed, and leave itunoccupied. Or, you may wish to geta smaller rear-facing child seat.
CONTINUED
Protecting Infants and Small Children
Child Seat Placement
Placing a forward-facing child seat inthe front seat of a vehicle equippedwith a passenger’s airbag can behazardous.
Child Seat Type
Protecting Small Children
Driver
andP
assengerSafety
33
Placing a rear-facing child seatin the front seat can result inserious injury or death if thepassenger’s front airbag inflates.
Always place a rear-facing childseat in the back seat, not thefront.
In seating positions and vehicles notequipped with LATCH, a LATCH-compatible child seat can be installedusing a seat belt.
Whatever type of seat you choose, toprovide proper protection, a childseat should meet threerequirements:
Look for FMVSS213 or CMVSS 213 on the box.
Rear-facing for infants, forward-facing for small children.
If it is necessary to put a forward-facing child seat in the front, movethe vehicle seat as far to the rear aspossible, be sure the child seat isfirmly secured to the vehicle, and thechild is properly strapped in the seat.
We also recommend selecting aLATCH-compatible seat with a rigid,rather than a flexible, anchor (seepage ).
Since LATCH-compatible child seatsare easier to install and reduce thepossibility of improper installation,we recommend selecting this style.
Conventional child seats must besecured to a vehicle with a seat belt,whereas LATCH-compatible seatsare secured by attaching the seat tohardware built into the two outerseating positions in the back seat.
When buying a child seat, you needto choose either a conventional childseat, or one designed for use withthe Lower Anchors and Tethers forChildren (LATCH) system.
36
The child seat should meet U.S. orCanadian Motor Vehicle SafetyStandard 213.
The child seat should be of theproper type and size to fit the child.
1.
2.
Protecting Infants and Small Children, Selecting a Child Seat
Selecting a Child Seat
34
Placing a forward-facing childseat in the front seat can resultin serious injury or death if thefront airbag inflates.
If you must place a forward-facing child seat in front, movethe vehicle seat as far back aspossible, and properly restrainthe child.
After selecting a proper child seat,and a good place to install the seat,there are three main steps ininstalling the seat:
All child seats must besecured to the vehicle with the lappart of a lap/shoulder belt or withthe LATCH (Lower Anchors andTethers for Children) system. Achild whose seat is not properlysecured to the vehicle can beendangered in a crash.
After installing a childseat, push and pull the seatforward and from side to side toverify that it is secure.
A child seat secured with a seat beltshould be installed as firmly aspossible. However, it does not needto be ‘‘rock solid.’’ Some side-to-side
movement can be expected andshould not reduce the child seat’seffectiveness.
If the child seat is not secure, tryinstalling it in a different seatingposition, or use a different style ofchild seat that can be firmly secured.
Make sure the child is properlystrapped in the child seataccording to the child seat maker’sinstructions. A child who is notproperly secured in a child seatcan be seriously injured in a crash.
The following pages provideguidelines on how to properly installa child seat. A forward-facing childseat is used in all examples, but theinstructions are the same for rear-facing child seats.
Before purchasing a conventionalchild seat, or using a previouslypurchased one, we recommend thatyou test the seat in the specificvehicle seating position (orpositions) where the seat will beused.
Selecting a Child Seat, Installing a Child Seat
Installing a Child Seat
Properly secure the child seat tothe vehicle.
Make sure the child seat is firmlysecured.
Secure the child in the child seat.
The child seat should fit thevehicle seating position (orpositions) where it will be used.
1.
2.
3.
3.
Driver
andP
assengerSafety
35
Place the child seat on the vehicleseat, then attach the seat to thelower anchors according to thechild seat maker’s instructions.
Your vehicle is equipped withLATCH (Lower Anchors andTethers for Children) at the outerrear seats.
The lower anchors are locatedbetween the seat-back and seatbottom, and are to be used only witha child seat designed for use withLATCH.
The location of each lower anchor isindicated by a small button above theanchor point.
Make sure there are no objectsnear the anchors that couldprevent a secure connectionbetween the child seat and theanchors.
Move the seat belt buckle ortongue away from the loweranchors.
To install a LATCH-compatible childseat:
Some LATCH-compatible seatshave a rigid-type connector asshown above.
1.
2.
3.
Installing a Child Seat
Installing a Child Seat withLATCH
36
LOWER ANCHORSRigid type
BUTTONS
Whatever type you have, followthe child seat maker’s instructionsfor adjusting or tightening the fit.
Other LATCH-compatible seatshave a flexible-type connector asshown above.
Lift the head restraint (see page), then route the tether strap
through the legs of the headrestraint, over the seat-back,making sure the strap is nottwisted.
Attach the tether strap hook to thetether anchor, then tighten thestrap as instructed by the childseat maker.
Push and pull the child seatforward and from side to side toverify that it is secure.
4.
6.
5.
7.
75
Installing a Child SeatD
riverand
Passenger
Safety
37
Flexible type ANCHOR
TETHER STRAP HOOK
To activate the lockable retractor,slowly pull the shoulder part of thebelt all the way out until it stops,then let the belt feed back into theretractor.
After the belt has retracted, tug onit. If the belt is locked, you will notbe able to pull it out. If you can pullthe belt out, it is not locked, andyou will need to repeat these steps.
When not using the LATCH system,all child seats must be secured to thevehicle with the lap part of a lap/shoulder belt.
With the child seat in the desiredseating position, route the beltthrough the child seat accordingto the seat maker’s instructions,then insert the latch plate into thebuckle.
In addition, the lap/shoulder belts inall seating positions except thedriver’s have a locking mechanismthat must be activated to secure achild seat.
1. 2.
3.
Installing a Child Seat
Installing a Child Seat with a SeatBelt
38
After confirming that the belt islocked, grab the shoulder part ofthe belt near the buckle, and pullup to remove any slack from thelap part of the belt. Remember, ifthe lap part of the belt is not tight,the child seat will not be secure.
Push and pull the child seatforward and from side to side toverify that it is secure enough tostay upright during normal drivingmaneuvers. If the child seat is notsecure, unlatch the belt, allow it toretract fully, then repeat thesesteps.
To remove slack, it may help toput weight on the child seat, orpush on the back of the seat whilepulling up on the belt.
To deactivate the lockingmechanism and remove a child seat,unlatch the buckle, unroute the seatbelt, and let the belt fully retract.
4. 5.
Installing a Child SeatD
riverand
Passenger
Safety
39
A child seat with a tether can beinstalled in any seating position inthe back seat, using one of theanchorage points shown above.
Since a tether can provide additionalsecurity to the lap/shoulder beltinstallation, we recommend using atether whenever one is required oravailable.
After properly securing the childseat (see page ), lift the headrestraint, then route the tetherstrap over the seat-back andthrough the head restraint legs.
Lift the anchor cover, then attachthe tether strap hook to theanchor, making sure the strap isnot twisted.
Follow steps 2 and 3 from theprevious column.
After properly securing the childseat (see page ), route thetether strap over the seat-back.
Tighten the strap according to theseat maker’s instructions.
1.
2.
3.
38
1.
2.
38
Installing a Child Seat with aTether
Installing a Child Seat
Using an Outer Anchor
Using the Center Anchor
40
TETHER ANCHORAGE POINTS
COVER
ANCHOR
TETHERSTRAPHOOK
ANCHOR
TETHER STRAPHOOK
Front
When a child reaches therecommended weight or height limitfor a forward-facing child seat, thechild should sit in a back seat on abooster seat and wear a lap/shoulderbelt.
The following pages giveinstructions on how to check properseat belt fit, what kind of boosterseat to use if one is needed, andimportant precautions for a childwho must sit in front.
To determine if a lap/shoulder beltproperly fits a child, have the childput on the seat belt, then askyourself:
Does the child sit all the way backagainst the seat?
Do the child’s knees bendcomfortably over the edge of theseat?
1.
2.
CONTINUED
Protecting Larger Children
Checking Seat Belt Fit
Driver
andP
assengerSafety
41
Allowing a child age 12 or underto sit in front can result in injuryor death if the passenger’s frontairbag inflates.
If a child must ride in front,move the vehicle seat as farback as possible, use a boosterseat if needed, have the childsit up properly and wear theseat belt properly.
Does the shoulder belt crossbetween the child’s neck and arm?
Is the lap part of the belt as low aspossible, touching the child’sthighs?
Will the child be able to stayseated like this for the whole trip?
If you answer yes to all thesequestions, the child is ready to wearthe lap/shoulder belt correctly. Ifyou answer no to any question, thechild needs to ride on a booster seat. A child who has outgrown a forward-
facing child seat should ride in aback seat and use a booster seatuntil the lap/shoulder belt fits themproperly without the booster.
Some states and Canadian provincesalso require children to use a boosterseat until they reach a given age orweight (e.g., 6 years or 60 lbs). Besure to check current laws in thestates or provinces where you intendto drive.
Booster seats can be high-back orlow-back. Whichever style you select,make sure the booster seat meetsfederal safety standards (see page
) and that you follow the boosterseat maker’s instructions.
If a child who uses a booster seatmust ride in front, move the vehicleseat as far back as possible, and besure the child is wearing the seatbelt properly.
3.
4.
5.
34
Protecting Larger Children
Using a Booster Seat
42
CONTINUED
A child may continue using a boosterseat until the tops of their ears areeven with the top of the vehicle’s orbooster’s seat-back. A child of thisheight should be tall enough to usethe lap/shoulder belt without abooster seat.
The National Highway Traffic SafetyAdministration and TransportCanada recommend that all childrenage 12 and under be properlyrestrained in a back seat.
If the passenger’s front airbaginflates in a moderate to severefrontal collision, the airbag can causeserious injuries to a child who isunrestrained, improperly restrained,sitting too close to the airbag, or outof position.
A side airbag also poses risks. If anypart of a larger child’s body is in thepath of a deploying side airbag, thechild could receive possibly seriousinjuries.
Of course, children vary widely. Andwhile age may be one indicator ofwhen a child can safely ride in front,there are other important factors youshould consider.
To safely ride in front, a child mustbe able to follow the rules, includingsitting properly, and wearing the seatbelt properly throughout a ride.
Physically, a child must be largeenough for the lap/shoulder belt toproperly fit (see pages and ). Ifthe seat belt does not fit properly,with or without the child sitting on abooster seat, the child should not sitin front.
4114
Protecting Larger Children
When Can a Larger Child Sit inFront
Physical Size
Maturity
Driver
andP
assengerSafety
43
If you decide that a child can safelyride up front, be sure to:
Carefully read the owner’s manual,and make sure you understand allseat belt instructions and all safetyinformation.
Move the vehicle seat to the rear-most position.
Have the child sit up straight, backagainst the seat, and feet on ornear the floor.
Check that the child’s seat belt isproperly and securely positioned.
Supervise the child. Even maturechildren sometimes need to bereminded to fasten the seat beltsor sit properly.
This could resultin serious neck injuries during acrash.
This couldcause very serious injuries duringa crash. It also increases thechance that the child will slideunder the belt in a crash and beinjured.
If they do, theycould be very seriously injured in acrash.
Devices intended toimprove a child’s comfort orreposition the shoulder part of aseat belt can make the belt lesseffective and increase the chanceof serious injury in a crash.
Protecting Larger Children
Additional Safety PrecautionsDo not let a child wear a seat beltacross the neck.
Do not let a child put the shoulderpart of a seat belt behind the backor under the arm.
Two children should never use thesame seat belt.
Do not put any accessories on aseat belt.
44
Your vehicle’s exhaust containscarbon monoxide gas. You shouldhave no problem with carbonmonoxide entering the vehicle innormal driving if you maintain yourvehicle properly.
High levels of carbon monoxide cancollect rapidly in enclosed areas,such as a garage. Do not run theengine with the garage door closed.Even with the door open, run theengine only long enough to move thevehicle out of the garage.
With the trunk open, airflow can pullexhaust gas into your vehicle’sinterior and create a hazardouscondition. If you must drive with thetrunk open, open all the windows andset the heating and cooling systemas shown below.
If you must sit in your parked vehiclewith the engine running, even in anunconfined area, adjust the heatingand cooling system as follows:
Select the fresh air mode.Select the mode.Turn the fan on high speed.Set the temperature control to acomfortable setting.
Have the exhaust system inspectedfor leaks whenever:
The vehicle is raised for an oilchange.
You notice a change in the soundof the exhaust.
The vehicle was in an accidentthat may have damaged theunderside.
1.2.3.4.
Carbon Monoxide HazardD
riverand
Passenger
Safety
45
Carbon monoxide gas is toxic.Breathing it can causeunconsciousness and even killyou.
Avoid any enclosed areas oractivities that expose you tocarbon monoxide.
These labels are in the locationsshown. They warn you of potentialhazards that could cause seriousinjury. Read these labels carefully.
If a label comes off or becomes hardto read (except for the U.S.dashboard label which may beremoved by the owner), contact yourdealer for a replacement.
U.S. models
Canadian models
U.S. models only
Safety Labels
46
RADIATOR CAP
SUN VISORDASHBOARD
On models without side airbags
On models with side airbags
On vehicle with side airbagsU.S. models Canadian models
Safety LabelsD
riverand
Passenger
Safety
47
HOOD DOORJAMBS
48
This section gives information aboutthe controls and displays thatcontribute to the daily operation ofyour vehicle. All the essentialcontrols are within easy reach.
...........................Control Locations . 50............................Instrument Panel . 51
..........Instrument Panel Indicators . 54.............................................Gauges . 58
...............Odometer/Trip Meter . 58..................................Fuel Gauge . 58
...................Temperature Gauge . 59Controls Near the Steering
...........................................Wheel . 60.Windshield Wipers and Washers . 61
...........Turn Signal and Headlights . 62........Instrument Panel Brightness . 63
.................Hazard Warning Button . 64
.................Rear Window Defogger . 64..........Steering Wheel Adjustment . 65
...............................Keys and Locks . 66........................Immobilizer System . 67
................................Ignition Switch . 68......................................Door Locks . 69
......................Power Door Locks . 69................................................Trunk . 70
........Emergency Trunk Opener . 70.......................Remote Transmitter . 71
Replacing the Transmitter.....................................Battery . 72
.................................................Seats . 73
..............................Power Windows . 78.........................................Moonroof . 79
.............................................Mirrors . 80.................................Parking Brake . 81
...........Interior Convenience Items . 82.......................Beverage Holders . 83
...............Console Compartment . 83....................................Glove Box . 84....................................Coat Hook . 84
.............................Center Pocket . 85...........Accessory Power Socket . 85
..............................Vanity Mirror . 85.................................Interior Lights . 86................................Ceiling Light . 86
..................Ignition Switch Light . 86
Instruments and ControlsInstrum
entsand
Controls
49
Control Locations
50
MIRRORCONTROLS
HEATING/COOLING CONTROLS
HOOD RELEASEHANDLE
CRUISE CONTROLBUTTONS
FUEL FILL DOOR RELEASE
A/T model is shown.
POWER WINDOWSWITCHES
AUDIO SYSTEM
MOONROOF SWITCH(P. 79)
POWER DOOR LOCKMASTER SWITCH(P. 69)
CRUISE CONTROLMASTER BUTTON(P. 117)
(P. 78)
(P. 124) (P. 117)
ACCESSORY POWERSOCKET(P. 85)
CLOCK(P. 115)
(P. 92)
HAZARD WARNING BUTTON
(P. 88)(P. 80)
(P. 64)
(P. 123)TRUNK RELEASE(P. 70)
* *
*
**
CONTINUEDThe U.S. instrument panel is shown. Differences for the Canadian models are noted in the text.Shift lever position indicators for HX model are shown on page .2:
1:142
Instrument PanelInstrum
entsand
Controls
U.S.: HX, LX, EX, and Special Edition, Canada: LX, Si
51
IMMOBILIZER SYSTEMINDICATOR
MAINTENANCEREQUIRED INDICATOR
SUPPLEMENTAL RESTRAINTSYSTEM INDICATOR
HIGH BEAM INDICATOR
CHARGING SYSTEMINDICATOR
LOW OIL PRESSUREINDICATOR
MALFUNCTION INDICATOR LAMP
CRUISE CONTROL INDICATOR
TRUNK-OPEN INDICATOR
ANTI-LOCK BRAKESYSTEM INDICATOR
LOW FUEL INDICATOR
(P. 56)
(P. 55)
(P. 54, 200)
(P. 54, 200)
(P. 54, 201)
(P. 138)SHIFT LEVER POSITION INDICATORS
(P. 54) (P. 56)
(P. 54)SIDE AIRBAG OFF INDICATOR
(P. 56)
(P. 57)
(P. 56)
(P. 55, 202)
(P. 54)SEAT BELT REMINDER INDICATOR
(P. 55)
PARKING BRAKE ANDBRAKE SYSTEMINDICATOR
2 1
1
Instrument Panel
Canada: DX, DX Special Edition, REVERB
52
LOW OIL PRESSUREINDICATOR
DAYTIME RUNNINGLIGHTS INDICATOR
MALFUNCTION INDICATOR LAMP
WASHER LEVELINDICATOR
TRUNK-OPEN INDICATOR
IMMOBILIZER SYSTEMINDICATOR
CHARGING SYSTEMINDICATOR
MAINTENANCE REQUIREDINDICATOR
PARKING BRAKE ANDBRAKE SYSTEMINDICATOR
LOW FUEL INDICATOR
SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR
HIGH BEAM INDICATOR
SIDE AIRBAG OFF INDICATOR
(P. 54)
(P. 56)
(P. 54, 200)
(P. 54, 200)
(P. 54, 201)
(P. 54)
(P. 55)
(P. 57)
(P. 55, 202)
(P. 56)
(P. 56)
(P. 55)
(P. 54)
(P. 56)
SEAT BELT REMINDER INDICATOR
Instrument Panel
U.S.: DX and Value Package
Instruments
andC
ontrols
53
SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR
IMMOBILIZER SYSTEMINDICATOR
LOW OIL PRESSUREINDICATOR
MAINTENANCE REQUIRED INDICATOR
TRUNK-OPEN INDICATOR
PARKING BRAKE ANDBRAKE SYSTEMINDICATOR
HIGH BEAM INDICATOR
LOW FUEL INDICATOR
CHARGING SYSTEMINDICATOR
MALFUNCTION INDICATOR LAMP
SIDE AIRBAG OFF INDICATOR
(P. 54)
(P. 56)
(P. 54, 200)
(P. 54, 200)
(P. 54)SEAT BELT REMINDER INDICATOR
(P. 55)
(P. 57)
(P. 55, 202)
(P. 56)
(P. 54)
(P. 56)
(P. 54, 201)
The instrument panel has manyindicators to give you importantinformation about your vehicle. If this indicator comes on when the
engine is running, the battery is notbeing charged. For more information,see page .
This indicator comes on when youturn the ignition switch to ON (II). Itreminds you and your passengers tofasten your seat belts. A beeper alsosounds if you have not fastened yourseat belt.
If you turn the ignition switch to ON(II) before fastening your seat belt,the beeper sounds and the indicatorflashes. If you do not fasten yourseat belt before the beeper stops, theindicator stops flashing but remainson.
If you continue driving withoutfastening your seat belt, the beepersounds and the indicator flashesagain at regular intervals.
This indicator comes on when youturn the ignition switch to ON (II). Ifit comes on at any other time, itindicates a potential problem withyour front airbags or automatic seatbelt tensioners. On models equippedwith side airbags, this indicator willalso alert you to a potential problemwith your side airbags or passenger’sside airbag automatic cutoff system.For more information, see page .
This indicator comes on when youturn the ignition switch to ON (II). Ifit comes on at any other time, itindicates that the passenger’s sideairbag has automatically shut off.For more information, see page .
The engine can be severely damagedif this indicator flashes or stays onwhen the engine is running. Formore information, see page .
See page .
200
200
201
25
26
If equipped
Supplemental RestraintSystem Indicator
Charging SystemIndicator
Low Oil PressureIndicator
Side Airbag Off Indicator
Seat Belt ReminderIndicator
Malfunction IndicatorLamp
Instrument Panel Indicators
54
CONTINUED
This indicator has two functions:
It comes on when you turn theignition switch ON (II). It is areminder to check the parkingbrake. Driving with the parkingbrake not fully released candamage the brakes and tires.
If it remains lit after you have fullyreleased the parking brake whilethe engine is running, or if itcomes on while driving, therecould be a problem with the brakesystem. For more information, seepage .
This indicator normally comes on fora few seconds when you turn theignition switch to ON (II), and whenthe ignition switch is turned toSTART (III). If it comes on at anyother time, there is a problem withthe ABS. If this happens, have yourvehicle checked at a dealer. Withthis indicator on, your vehicle stillhas normal braking ability but noanti-lock function. For moreinformation, see page .
This indicator comes on with thehigh beam headlights. For moreinformation, see page .
On Canadian models, this indicatorcomes on with reduced brightnesswhen the Daytime Running Lights(DRL) are on (see page ).
This indicator comes on when youturn the ignition switch to ON (II)with the headlight switch off and theparking brake set. It should go off ifyou turn on the headlights or releasethe parking brake. If it comes on atany other time, it means there is aproblem with the DRL. There mayalso be a problem with the highbeam headlights.
1.
2.
202
147
62
62
If equipped
Canadian models only
Anti-lock Brake System(ABS) Indicator
Parking Brake and Brake SystemIndicator
High Beam Indicator
‘‘Daytime RunningLights’’ Indicator
Instrument Panel IndicatorsInstrum
entsand
Controls
55
U.S. Canada
This indicator comes on if the trunklid is not closed tightly.
This indicator comes on as areminder that you must refuel soon.
This indicator comes on when youset the cruise control. See page
for information on operating thecruise control.
This indicator also blinks severaltimes when you turn the ignitionswitch from ON (II) to ACCESSORY(I) or LOCK (0).
This indicator comes on when thewasher fluid level is low. Add washerfluid when you see this indicator(see page ).
The left or right turn signal indicatorblinks when you signal a lane changeor turn. If the indicator does notblink or blinks rapidly, it usuallymeans one of the turn signal bulbs isburned out (see page ). Replacethe bulb as soon as possible, sinceother drivers cannot see that you aresignaling.
When you press the hazard warningbutton, both turn signal indicatorsblink. All turn signals on the outsideof the vehicle should flash.
This indicator comes on for a fewseconds when you turn the ignitionswitch to ON (II). It will then go offif you have inserted a properly-codedignition key. If it is not a properly-coded key, the indicator will blink,and the engine will not start (seepage ).
172
117
67164
Canadian models only
If equipped
Trunk-open Indicator
Low Fuel Indicator
Washer Level Indicator
Cruise Control Indicator
Immobilizer SystemIndicator
Turn Signal and Hazard WarningIndicators
Instrument Panel Indicators
56
Press and hold the Select/Resetknob in the instrument panel, thenturn the ignition switch to ON (II).
Hold the knob for about 10seconds until the indicator goesoff.
If you exceed 10,000 miles (16,000km) without having the scheduledmaintenance performed, thisindicator will remain on as a constantreminder.
Your dealer will reset this indicatorafter completing the scheduledmaintenance. If this maintenance isdone by someone other than yourdealer, reset the indicator as follows.
This indicator reminds you that it istime to take your vehicle in forscheduled maintenance.Refer to the Maintenance Schedulesfor Normal and Severe DrivingConditions on pages and .
For the first 8,000 miles (12,800 km)after the Maintenance RequiredIndicator is reset, it will come on for2 seconds when you turn the ignitionswitch to ON (II).
Turn off the engine.
Between 8,000 miles (12,800 km)and 10,000 miles (16,000 km), thisindicator will come on for 2 secondswhen you first turn the ignitionswitch to ON (II), and then flash for10 seconds.
1.
2.
3.
153 154
Maintenance RequiredIndicator
Instrument Panel IndicatorsInstrum
entsand
Controls
57
The odometer shows the totaldistance your vehicle has beendriven. It measures miles in U.S.models and kilometers in Canadianmodels. It is illegal under U.S.federal law and Canadian provincialregulations to disconnect, reset, oralter the odometer with the intent tochange the number of miles orkilometers indicated.
The odometer and the trip metersuse the same display. Switchbetween these displays by pressingthe Select/Reset knob repeatedly.When you turn the ignition switch toON (II), the meter you last selectedis displayed.
The trip meter shows the number ofmiles (U.S.) or kilometers (Canada)driven since you last reset it.
There are two trip meters: Trip Aand Trip B. Each trip meter worksindependently, so you can keep trackof two different distances.
To reset a trip meter, display it andthen press and hold the Select/Resetknob until the number resets to ‘‘0.0’’.
Both trip meters will reset if thevehicle’s battery goes dead or isdisconnected.
This shows how much fuel you have.It may show slightly more or lessthan the actual amount. The needlereturns to the bottom after you turnoff the ignition.
Gauges
Odometer/Trip Meter
Fuel Gauge
U.S.: HX, LX, EX, and Special Edition, Canada: LX, Si
58
TEMPERATURE GAUGE
FUEL GAUGE
ODOMETER/TRIP METER
TACHOMETER
SPEEDOMETER
SELECT/RESET KNOBU.S. instrumentpanel is shown.
Avoid driving with an extremely lowf uel level. Running out of f uel couldcause the engine to misf ire, damagingthe catalytic converter.
This shows the temperature of theengine’s coolant. During normaloperation, the pointer should rise toabout the middle of the gauge. Insevere driving conditions, such asvery hot weather or a long period ofuphill driving, the pointer may rise tothe upper zone. If it reaches the red(Hot) mark, pull safely to the side ofthe road. See page forinstructions and precautions onchecking the engine’s coolingsystem.
197
Gauges
Temperature GaugeU.S. DX, Value Package
Canada: DX, DX Special Edition, REVERB
Instruments
andC
ontrols
59
SPEEDOMETER
SELECT/RESET KNOB
TACHOMETER
TEMPERATUREGAUGE
ODOMETER/TRIP METER
FUEL GAUGE
FUEL GAUGE SPEEDOMETERTEMPERATUREGAUGE
ODOMETER/TRIP METER SELECT/RESET KNOB
*
*
To use the horn, press the center pad of the steering wheel.
Controls Near the Steering Wheel
60
MIRROR CONTROLS
REAR WINDOWDEFOGGER
WINDSHIELDWIPERS/WASHERS
MOONROOFSWITCH
(P. 117)
(P. 80)
STEERING WHEEL ADJUSTMENT(P. 65)
(P. 64)
(P. 64)(P. 61)(P. 79)
HORN
HAZARD WARNING BUTTONINSTRUMENTPANELBRIGHTNESS(P. 63)
HEADLIGHTS/ TURNSIGNALS(P. 62)
CRUISE CONTROL BUTTONS(P. 117)
CRUISE CONTROLMASTER BUTTON
---
-
-
-
-
-
-
Push the right lever up or down toselect a position.
MISTOFFINT IntermittentLO Low speedHI High speedWindshield Washers
The wipers run at highspeed until you release the lever.
The wipers are not activated.
The wipers operate everyfew seconds. In low speed and highspeed, the wipers run continuously.
Vary the delay by turning the INTTIME ring.
The wipers run at low speed.
The wipers run at high speed.
Pull thewiper control lever toward you andhold it. The washers spray until yourelease the lever. The wipers run atlow speed, then complete one moresweep after you release the lever.
1.2.3.4.5.6.
On EX models in U.S., and Si models inCanada
Windshield Wipers and Washers
MIST
OFF
INT
LO
HI
Windshield Washers
Instruments
andC
ontrols
61
-
-
-
Turn SignalOffParking and indicator lightsHeadlights onHigh beamsFlash high beams
Push down on theleft lever to signal a left turn and upto signal a right turn. To signal a lanechange, push lightly on the lever andhold it. The lever will return tocenter when you release it orcomplete a turn.
Turning theswitch to the ‘‘ ’’ position turnson the parking lights, taillights,instrument panel lights, side-markerlights, and rear license plate lights.
Turning the switch to the ‘‘ ’’position turns on the headlights. Ifyou leave the lights on with the keyremoved from the ignition switch,you will hear a reminder tone whenyou open the driver’s door.
Push the leverforward until you hear a click to turnon the high beams. The blue highbeam indicator will come on (seepage ). Pull the lever back to
return to the low beams.
To flash the high beams, pull thelever back lightly, then release it.The high beams will stay on as longas you hold the lever back.
With the headlight switch off, thehigh beam headlights and the highbeam indicator come on withreduced brightness when you turnthe ignition switch to ON (II) andrelease the parking brake. Theyremain on until you turn the ignitionswitch off, even if you set theparking brake.
The headlights revert to normaloperation when you turn them onwith the switch.
1.2.3.4.5.6.
55
Canadian models only
Turn Signal and Headlights
Turn Signal
Headlights On
High Beams
Daytime Running Lights
62
The knob on the instrument panelcontrols the brightness of the instru-ment panel lights. Turn the knob toadjust the brightness.
Adjust the brightness to the desiredlevel with the headlight switch off,and also with the headlight switch on.
To reduce glare at night, theinstrument panel illumination dimswhen you turn the light switch to
or . Turning the Select/Reset knob fully to the right willreturn the instrument panel to thebrightness adjusted with theheadlight switch off and a tone willsound.
There are six brightness levels.When you turn the knob, theodometer/trip meter displaychanges to circles that show you thecurrent level. You will hear a tonewhen you reach the maximum orminimum brightness.
On all models except DX, Value Packageand REVERB
Instrument Panel BrightnessInstrum
entsand
Controls
63
SELECT/RESET KNOB
KNOBDX, Value Packageand REVERB models
All models except DX, ValuePackage and REVERB
Make sure the rear window is clearand you have good visibility beforestarting to drive.
The defogger and antenna wires onthe inside of the rear window can beaccidentally damaged. Whencleaning the glass, always wipe sideto side.
Push the button between the centervents to turn on the hazard warninglights (four-way flashers). Thiscauses all four outside turn signalsand both indicators in the instrumentpanel to flash. Use the hazardwarning lights if you need to park ina dangerous area near heavy traffic,or if your vehicle is disabled.
The rear window defogger will clearfog, frost, and thin ice from thewindow. Push the defogger button toturn it on and off. The indicator inthe button comes on to show thedefogger is on. If you do not turn itoff, the defogger will shut itself offafter about 15 minutes. It also shutsoff when you turn off the ignitionswitch. You have to turn thedefogger on again when you restartthe vehicle.
Rear Window DefoggerHazard Warning Button
Hazard Warning Button, Rear Window Defogger
64
Make sure you have securelylocked the steering wheel in placeby trying to move it up and down.
Make any steering wheel adjustmentbefore you start driving.
Push the lever under the steeringcolumn all the way down.
Move the steering wheel up ordown to the desired position.Make sure you can see theinstrument panel gauges andindicators.
Push the lever up to lock thesteering wheel in position.
1.
4.
3.
2.
Steering Wheel AdjustmentInstrum
entsand
Controls
65
Adjusting the steering wheelposition while driving maycause you to lose control of thevehicle and be seriously injuredin a crash.
Adjust the steering wheel onlywhen the vehicle is stopped.
Protect the keys from directsunlight, high temperature, andhigh humidity.
Do not drop the keys or set heavyobjects on them.
Keep the keys away from liquids.If they get wet, dry themimmediately with a soft cloth.
The master key fits all the locks onyour vehicle. The valet key worksonly in the ignition and the doorlocks. You can keep the trunk, trunkrelease handle and rear seat trunkaccess locked when you leave yourvehicle and the valet key at a parkingfacility.
The keys do not contain batteries.Do not try to take them apart.
You should have received a keynumber tag with your keys. You willneed this key number if you everhave to get a lost key replaced. Useonly Honda-approved key blanks.
These keys contain electroniccircuits that are activated by theimmobilizer system. They will notwork to start the engine if thecircuits are damaged.
Keys and Locks
66
MASTERKEYS (Black)
VALETKEY (Gray)
KEYNUMBERTAG
The system may not recognize yourkey’s coding if another immobilizerkey or other metal object (i.e. keyfob) is near the ignition switch whenyou insert the key.
If the system repeatedly does notrecognize the coding of your key,contact your dealer.
Do not attempt to alter this systemor add other devices to it. Electricalproblems could result that may makeyour vehicle undriveable.
If you have lost your key and cannotstart your engine, contact yourdealer.
When you turn the ignition switch toON (II), the immobilizer systemindicator should come on for a fewseconds, then go out. If the indicatorstarts to blink, it means the systemdoes not recognize the coding of thekey. Turn the ignition switch toLOCK (0), remove the key, reinsertit, and turn the switch to ON (II)again.
The immobilizer system protectsyour vehicle from theft. If animproperly-coded key (or otherdevice) is used, the engine’s fuelsystem is disabled.
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thefollowing two conditions: (1) This devicemay not cause harmful interference, and(2) this device must accept anyinterference received, includinginterference that may cause undesiredoperation.
Changes or modifications not expresslyapproved by the party responsible forcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the following twoconditions: (1) this device may not causeinterference, and (2) this device mustaccept any interference that may causeundesired operation of the device.
Immobilizer SystemInstrum
entsand
Controls
67
--
-
-
The ignition switch has fourpositions: LOCK (0), ACCESSORY(I), ON (II), START (III)
If the front wheels are turned, theanti-theft lock may make it difficultto turn the key. Firmly turn thesteering wheel to the left or right asyou turn the key.
Use this positiononly to start the engine. The switchreturns to ON (II) when you let go ofthe key.
You can insert orremove the key only in this position.To turn the key, push it in slightly. Ifyour vehicle has an automatictransmission, the shift lever mustalso be in park.
You canoperate the audio system and theaccessory power socket in thisposition.
This is the normal keyposition when driving. Several of theindicators on the instrument panelcome on as a test when you turn theignition switch from ACCESSORY(I) to ON (II).
You will hear a reminder beeper ifyou leave the key in the ignitionswitch in the LOCK (0) orACCESSORY (I) position and openthe driver’s door. Remove the key toturn off the beeper.
If your vehicle has an automatictransmission, the shift lever must bein Park before you can remove thekey from the ignition switch.
START (III)LOCK (0)
ACCESSORY (I)
ON (II)
Ignition Switch
68
Removing the key from theignition switch while drivinglocks the steering. This cancause you to lose control.
Remove the key from theignition switch only whenparked.
Each door has a lock tab on the top.Push the tab down to lock the doorand pull it up to unlock.
To lock the passenger’s door whengetting out of the vehicle, push thelock tab down and close the door. Tolock the driver’s door, pull and holdthe outside door handle then pushthe lock tab down. Release thehandle, then close the door.
To lock the doors, press the masterdoor lock switch on the driver’s door,press the lock tab down on thedriver’s door, or use the key on theoutside lock on the driver’s door.
Pressing up on the master door lockswitch will unlock both doors.
Only the driver’s door unlocks whenyou use the driver’s door lock tab orthe key on the outside driver’s doorlock.
If equipped
Door Locks Power Door Locks
Door LocksInstrum
entsand
Controls
69
Lock
Unlock
MASTER DOOR LOCK SWITCH
Lock
Unlock
LOCK TAB
As a safety feature, your vehicle hasa release lever on the trunk latch sothe trunk can be opened from theinside. To open the trunk, push therelease lever to the left.
Parents should decide if theirchildren should be shown how to usethis feature. For more informationabout child safety, see page .
You can also use the master key toopen the trunk lock. The valet keydoes not work in this lock.
To open the trunk, pull the trunkrelease handle to the left of thedriver’s seat. To protect items in thetrunk when you need to give the keyto someone else, lock the trunkrelease handle with the master keyand give the other person the valetkey.
To close the trunk, press down onthe trunk lid.
Keep the trunk lid closed at all timeswhile driving to avoid damaging thelid, and to prevent exhaust gas fromgetting into the interior. See
on page .30
45
Emergency Trunk Opener
CarbonMonoxide Hazard
Trunk
70
MASTER KEY
TRUNK RELEASE HANDLE
MASTER KEY
Pull
-
- -
If equippedPress this button once to
lock both doors. Some exterior lightswill flash once. When you pushLOCK twice within 5 seconds, youwill hear a beep to verify that thedoors are locked. You cannot lockthe doors if either door is not fullyclosed or the key is in the ignitionswitch.
Press this button onceto unlock the driver’s door. Someexterior lights will flash twice. Pushit twice to unlock the passenger’sdoor.
Press this button forabout 2 seconds to attract attention:the horn will sound and the exteriorlights will flash for about 30 seconds.To cancel panic mode, press anyother button on the remotetransmitter, or turn the ignitionswitch to ON (II).
The ceiling light (if the ceiling lightswitch is in the center position) willcome on when you press theUNLOCK button. If you do not openeither door within 30 seconds, thelight fades out. If you relock thedoors with the remote transmitterbefore 30 seconds have elapsed, thelight will go off immediately.
If you do not open either door within30 seconds, they will automaticallyrelock.
Avoid dropping or throwing thetransmitter.Protect the transmitter fromextreme temperature.Do not immerse the transmitter inany liquid.If you lose a transmitter, thereplacement needs to bereprogrammed by your dealer.
Remote Transmitter
LOCK
UNLOCK PANIC
Remote Transmitter Care
Instruments
andC
ontrols
71
LED LOCKBUTTON
UNLOCKBUTTON
PANICBUTTON
+
◎▽
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thefollowing two conditions: (1) This devicemay not cause harmful interference, and(2) this device must accept anyinterference received, includinginterference that may cause undesiredoperation.
Changes or modifications not expresslyapproved by the party responsible forcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the following twoconditions: (1) this device may not causeinterference, and (2) this device mustaccept any interference that may causeundesired operation of the device.
If it takes several pushes on thebutton to lock or unlock the doors,replace the battery as soon aspossible.
Battery type: CR2025
To replace the battery, remove theround cover on the back of thetransmitter by turning itcounterclockwise with a coin. Inserta new battery with the side facingup. Reinstall the cushion ring. Alignthe mark on the cover with the
mark on the transmitter. Setthe cover in place, and turn itclockwise.
Replacing the TransmitterBattery
Remote Transmitter
72
ROUNDCOVER
CUSHIONRING
BATTERY
Open
Close
-
To change the seat-back angle, pullup on the lever on the outside of theseat bottom.
Make all seat adjustments beforeyou start driving.
To adjust the seat forward andbackward, pull up on the bar underthe seat cushion’s front edge. Try tomove the seat to make sure it islocked in position.
See pages for important safetyinformation and warnings about how toproperly position the seats and seat-backs.
11 13Front Seat Adjustments
SeatsInstrum
entsand
Controls
73
To get into the rear seat on thedriver’s side, pull up on the seat-backadjustment lever.
On all other models, push down therelease lever at the base of the seat-back. The seat-back will tilt forwardand the whole seat will slide forward.
The height of the driver’s seat isadjustable. Turn the dial on theoutside of the seat cushion.
To get into the rear seat from thepassenger’s side in the U.S. DX andValue Package models, pull up theseat-back adjustment lever. The seat-back will tilt forward. If more room isneeded, use the seat adjustment barto move the seat forward.
If equipped
Driver’s Seat Height Adjustment Rear Seat Access
Seats
74
RELEASELEVER
SEAT-BACKADJUSTMENT LEVER
When you return the seat-backupright, the seat stays in the fullyforward position. Use the seatadjustment bar and the seat-backadjustment lever to move the seat tothe desired position. Make sure theseat is fully latched before sitting init.
Your vehicle is equipped with headrestraints in the front seats and theoutboard seating positions in therear.
As you return the seat-back upright,push the whole seat backward until itlatches. Make sure the seat is fullylatched before sitting in it.
The head restraints help protect youand your passengers from whiplashand other injuries.
They are most effective when youadjust them so the back of theoccupant’s head rests against thecenter of the restraint.
The head restraints in the front andrear outboard seating positionsadjust for height. You need bothhands to adjust the restraint. Do notattempt to adjust it while driving. Toraise it, pull upward. To lower therestraint, push the release buttonsideways and push the restraintdown.
See page for important safetyinformation and a warning about how toproperly position the head restraints.
On HX model in the U.S., and allCanadian models 13
On LX, EX, and Special Edition modelsin the U.S.
Head Restraints
SeatsInstrum
entsand
Controls
75
FRONT
RELEASE BUTTON
The left and right halves can befolded separately from inside thevehicle or inside the trunk. To folddown the seat-back from inside thevehicle, insert the master key in thelock on the rear shelf. To fold downthe driver’s side, turn the keyclockwise, pull down the top of theseat-back, then release the key. Tofold down the passenger’s side, turnthe key counterclockwise andperform the same procedure.
When storing cargo, you can movethe rear center shoulder belt out ofthe way by removing the belt fromthe guide.
The lid of the console compartmentcan be used as an armrest.
Make sure the passenger’s hands orfingers are away from the armrestbefore pushing it down.
If equipped
Folding Rear SeatArmrest
Seats
76
GUIDE
CENTER SHOULDER BELT
To release the seat-back from insidethe trunk, pull the release under thetrunk panel. Push the seat-backdown, then let go of the release.
To lock the seat-back upright, push itfirmly against the trunk panel. Makesure it is latched in place by pullingon the top of the seat.
Make sure all rear shoulder belts arepositioned in front of the rear seat-back whenever it is in the uprightposition.
Do not put any heavy items on theseat-back when it is folded.
Make sure all items in the trunk, oritems extending through the openinginto the back seat, are secured.Loose items can fly forward andcause injury if you have to brakehard. See on page
.
Never drive with the seat-backfolded down and the trunk lid open.See onpage .
130
45
Carrying Cargo
Carbon Monoxide Hazard
SeatsInstrum
entsand
Controls
77
RELEASE
Pull Pull
-
If equippedTurn the ignition switch to ON (II)to raise or lower either window. Toopen the window, push the switchdown and hold it. Release the switchwhen you want to stop the window.Pull back on the switch and hold it toclose the window.
To open the driver’swindow fully, push the windowswitch firmly down to the seconddetent, and release it. The windowwill automatically go down all theway. To stop the window, pull backon the window switch briefly.
When you push the MAIN switch in,the switch is OFF, and thepassenger’s window cannot be raisedor lowered. To cancel this feature,push on the switch again to get it topop out. Keep the MAIN switch offwhen you have children in thevehicle so they do not injurethemselves by operating the windowunintentionally.
AUTO
Power Windows
78
MAIN SWITCH
DRIVER’S WINDOW SWITCH
Closing a power window onsomeone’s hands or fingers cancause serious injury.
Make sure your passenger isaway from the window beforeclosing it.
If equippedThe moonroof can be tilted up in theback for ventilation, or it can be slidback into the roof. Use the switchunder the left dashboard vent tooperate the moonroof. You mustturn the ignition switch to ON (II)for the moonroof to operate.
To tilt up the back of the moonroof,press and hold the center button( ). To close the moonroof,press and hold the top of the switch( ). To open the moonroof,press and hold the bottom of theswitch ( ).
MoonroofInstrum
entsand
Controls
79
MOONROOF SWITCH
TILT BUTTON Opening or closing themoonroof on someone’s handsor fingers can cause seriousinjury.
Make sure all hands and fingersare clear of the moonroofbefore opening or closing it.
If you try to open the moonroof inbelow-f reezing temperatures, or whenit is covered with snow or ice, you candamage the moonroof panel or motor.
Push the appropriate edge of theadjustment switch to move themirror right, left, up, or down.
The inside mirror has day and nightpositions. The night position reducesglare from headlights behind you.Flip the tab on the bottom edge ofthe mirror to select the day or nightposition.
Keep the inside and outside mirrorsclean and adjusted for best visibility.Be sure to adjust the mirrors beforeyou start driving.
When you finish, move theselector switch to the center (off)position. This turns theadjustment switch off to keep yoursettings.
Turn the ignition switch to ON (II).
Move the selector switch to L(driver’s side) or R (passenger’sside).
1.
2.
3.
4.
If equipped
Adjusting the Power Mirrors
Mirrors
80
SELECTOR SWITCH
ADJUSTMENT SWITCH
TAB
The outside mirrors are heated toremove fog and frost. With theignition switch in the ON (II)position, turn on the heaters bypressing the button. The indicator inthe button comes on as a reminder.Press the button again to turn theheaters off.
To apply the parking brake, pull thelever up fully. To release it, pull upslightly, push the button, and lowerthe lever. The parking brakeindicator on the instrument panelshould go out when the parkingbrake is fully released (see page ).55
On Canadian Si models
Power Mirror Heaters Parking Brake
Mirrors, Parking BrakeInstrum
entsand
Controls
81
PARKING BRAKELEVER
U.S. : Value Package, LX, EX, SpecialEditionCanada: DX Special Edition, REVERB,LX, Si
PARKING BRAKE LEVER
U.S. : DX, HXCanada: DX
Driving the vehicle with the parkingbrake applied can damage the rearbrakes and axles.
*
*
*
*
Interior Convenience Items
82
VANITY MIRROR
GLOVE BOX
COIN BOX
ACCESSORYPOWER SOCKET
COAT HOOK
BEVERAGE HOLDER
CONSOLE COMPARTMENT
BEVERAGE HOLDER
:If equipped
CENTER POCKET
Be careful when you are using thebeverage holders. A spilled liquidthat is very hot can scald you or yourpassengers. Spilled liquids candamage the upholstery, carpeting,and electrical components in theinterior.
To open the console compartment,pull the lever and lift the lid.
To close, lower the lid and push itdown until it latches.
Open the front beverage holder bypushing on the top.
On the U.S. EX models, open therear beverage holder by pushing onthe back and pulling the holder allthe way out.
If equipped
If equipped
Beverage Holders Console Compartment
Interior Convenience ItemsInstrum
entsand
Controls
83
LEVER
CONSOLE COMPARTMENT
PushPull
Push
Open the glove box by squeezing thehandle. Close it with a firm push.
To use a coat hook, push on the lid.Close it with a firm push.
Make sure the coat hook is closedwhen you are not using it. This hookis not designed for large or heavyitems.
Glove Box Coat Hook
Interior Convenience Items
84
COAT HOOK
An open glove box can causeserious injury to your passengerin a crash, even if thepassenger is wearing the seatbelt.
Always keep the glove boxclosed while driving.
To use an accessory power socket,pull up the cover.To open the lid, pull it down. Close it
with a firm push.To use a vanity mirror on the back ofthe sun visor, pull up the cover.
They will not power an automotivetype cigarette lighter element.
To use an accessory, the ignitionswitch must be in the ACCESSORY(I) or ON (II) position.
This socket is intended to supplypower for 12 volt DC accessoriesthat are rated 120 watts or less (10amps).
If equipped
Center Pocket Accessory Power Socket
Vanity Mirror
Interior Convenience ItemsInstrum
entsand
Controls
85
Push on the spotlight lenses to turnthe light on and off.
The ignition switch light comes onwhen you open the driver’s door. Itgoes out several seconds after thedoor is closed.
If you leave either door open withthe key not in the ignition switch, theceiling light will go off after 3minutes.
The front ceiling light also containstwo spotlights. Push the button nextto each light to turn the spotlight onand off. You can use the spotlights atall times.
The ceiling light has a three-positionswitch: ON, Door Activated, andOFF. In the Door Activated (center)position, the light comes on whenyou:
Open either door.Remove the key from the ignitionswitch.If you do not open a door, the lightfades out in about 10 seconds.Unlock the doors with the key orremote transmitter.
On LX models
On U.S. EX and Canadian Si modelsOn U.S. EX and Canadian Si models
Ceiling Light
Ignition Switch Light
Interior Lights
86
DOOR ACTIVATED
ON
OFF
OFF
ON
FRONTDOOR ACTIVATED
*
*
The heating and air conditioningsystems in your vehicle provide acomfortable driving environment inall weather conditions.
...............Vents, Heating, and A/C . 88..........................Airflow Controls . 89
............................Playing the Radio . 92..............................Radio Reception . 97
..................................Playing a Disc . 99..................Protecting Your Discs . 108
.........CD Player Error Messages . 109CD Changer Error
...................................Messages . 110...............................Playing a Tape . 111
.................Radio Theft Protection . 114..........................Setting the Clock . 115
...............................Cruise Control . 117
Your vehicle has an anti-theft audiosystem that requires a code numberto enable it.
The standard audio system hasmany features. This section de-scribes those features and how touse them. (If you selected anoptional audio system, refer to theoperating instructions that camewith it.)
Air conditioning is standard on LX,Value Package, Special Edition, andEX models in the U.S., and DXSpecial Edition, REVERB, LX and Simodels in Canada. It is optional onother models.
Standard for Value Package, HX, LX, EXand Special Edition models in the U.S.,and DX Special Edition, REVERB, LXand Si models in Canada
FeaturesF
eatures
87
Vents, Heating, and A/C
88
MODE CONTROL DIAL
TEMPERATURECONTROL DIAL
FAN CONTROL DIAL REAR WINDOWDEFOGGERBUTTON
AIR CONDITIONING(A/C) BUTTON
RECIRCULATION BUTTON
Air flows from the defrostervents at the base of the windshield.
Air flows from the centerand corner vents in the dashboard.
The outside air intakes for theheating and cooling system are atthe base of the windshield. Keep thisarea clear of leaves and other debris.
Switch to recirculation mode whendriving through dusty or smokyconditions, then return to fresh airmode.
This button turns the rear windowdefogger off and on (see page ).
Turning this dial clockwise increasesthe temperature of the airflow.
This button turns the airconditioning on and off. Theindicator in the button is on whenthe A/C is on.
Use the mode control dial to selectthe vents the air flows from. Someair will flow from the dashboardcorner vents in all modes.
Airflow is divided betweenthe vents in the dashboard and thefloor vents.
Airflow is divided betweenthe floor vents and the defrostervents at the base of the windshield.
When you select or ,the system automatically switches tofresh air mode and turns on the A/C.You cannot turn the A/C off in thismode.
Turn this dial to increase or decreasethe fan speed and airflow.
When the recirculation indicator ison, air from the vehicle’s interior issent throughout the system again.When the indicator is off, air isbrought in from the outside of thevehicle (fresh air mode).
The system should be left in freshair mode under almost all conditions.Keeping the system in recirculationmode, particularly with the A/C off,can cause the windows to fog up.
Air flows from the floorvents. When you select , thesystem automatically switches tofresh air mode.
64
Optional on DX and HX models
Rear Window Defogger Button
Mode Control Dial
Fan Control Dial
Airflow Controls
Temperature Control Dial
Air Conditioning (A/C) Button
Recirculation Button
Vents, Heating, and A/CF
eatures
89
The flow-through ventilation systemdraws in outside air, circulates itthrough the interior, then exhausts itthrough vents near the rear window.
The heater uses engine coolant towarm the air. If the engine is cold, itwill be several minutes before youfeel warm air coming from thesystem.
Air conditioning places an extra loadon the engine. Watch the enginecoolant temperature gauge (see page
). If it moves near the red zone,turn off the A/C until the gaugereads normally.
Air conditioning, as it cools, removesmoisture from the air. When used incombination with the heater, itmakes the interior warm and dry.
This setting is suitable for all drivingconditions whenever the outsidetemperature is above 32°F (0°C).
Set the temperature to the lowerlimit.Make sure the A/C is off.Select and fresh air mode.Set the fan to the desired speed.
Select .When you select , the systemautomatically switches to fresh airmode.Set the fan to the desired speed.Adjust the warmth of the air withthe temperature control dial.
Turn on the A/C by pressing thebutton. The indicator in the buttoncomes on when a fan speed isselected.Make sure the temperature is setto maximum cool.Select .If the outside air is humid, selectrecirculation mode. If the outsideair is dry, select fresh air mode.Set the fan to the desired speed.
you cancool it down more rapidly by partiallyopening the windows, turning on theA/C, and setting the fan tomaximum speed in fresh air mode.
Turn the fan on.Turn on the air conditioning.Select and fresh air mode.Adjust the temperature to yourpreference.
1.
2.3.4.
1.
2.
3.4.
5.1.
2.3.
59
1.2.3.4.
If the interior is very warm,
Vents, Heating, and A/C
Ventilation
Using the Heater
Using the A/C Dehumidify the Interior
90
To remove fog from the inside of thewindows:
When you switch to another modefrom , the A/C stays on.Press the A/C button to turn it off.
Keep the system completely offfor short periods only.
To keep stale air and mustinessfrom collecting, you should havethe fan running at all times.
Select . The systemautomatically switches to fresh airmode and turns on the A/C.The A/C indicator does not comeon if it was off to start with.Select .Set the fan and temperaturecontrols to maximum level.
To clear the windows faster, you canclose the dashboard corner vents byrotating the wheel below each vent.This sends more warm air to thewindshield defroster vents. Once thewindshield is clear, select fresh airmode to avoid fogging the windows.
For your safety, make sure you havea clear view through all the windowsbefore driving.
Turning the fan speed andtemperature control dials all the wayto the left shuts off the systemcompletely.Set the fan to the desired speed, or
high for faster defrosting.Select . The systemautomatically switches to fresh airmode and turns on the A/C. TheA/C indicator will not come on if itwas off to start with.Adjust the temperature so theairflow feels warm.Select to help clear therear window.To increase airflow to thewindshield, close the corner vents.
1.
2.3.
1.
2.
3.
4.
5.
Vents, Heating, and A/C
To Defog and Defrost To Remove Exterior Frost or IceFrom the Windows
To Turn Everything Off
Features
91
Playing the Radio
92
AM/FM BUTTON
TUNE KNOB
SCAN INDICATOR
SEEK BAR
PRESET BUTTONS
TUNE KNOB
SCAN INDICATOR
STEREO INDICATOR
AM/FM BUTTON
STEREO INDICATOR
SEEK BAR
FM/AMBUTTON
SEEK BARAUTO SELECTBUTTON
SOUNDBUTTON
SCANBUTTON
PRESET BUTTONSPRESET BUTTONS
SCANBUTTON
AUTO SELECT BUTTON
PRESET BUTTONS
POWER/VOLUMEKNOB
DX model
POWER/VOLUMEKNOB
AUTO SELECTBUTTON
POWER/VOLUMEKNOB
PRESET CALL BAR
SCAN BUTTON
Audio System with In-dash CD Changer
STEREO INDICATOR
U.S. :Special Edition modelsCanada:REVERB, Si-GA models
U.S.: Value Package, HX, LX, EX modelsCanada: DX Special Edition, LX, Si-G models
-
-
-
The ignition switch must be in theACCESSORY (I) or ON (II) position.Turn the system on by pushing thePower Volume knob or the AM/FMbutton (FM/AM button on modelswith in-dash CD changer). Adjust thevolume by turning the PowerVolume knob.
As you adjust a volume, you will heara beep whenever the adjustmentlevel reaches the maximum andminimum of its range.
The band and frequency that theradio was last tuned to is displayed.To change bands, press the AM/FMor FM/AM button. On the FM band,ST will be displayed if the station isbroadcasting in stereo. Stereoreproduction on AM is not available.
On the AM band, AM noisereduction turns on automatically.
You can use any of five methods tofind a radio station on the selectedband: thepreset buttons, and .
Use the TUNE knob orthe SEEK bar to tune the radio to adesired frequency.
Turn the knob to the right to tune ahigher frequency, and turn it to theleft to tune a lower frequency.
Press the side of the SEEK barto tune a higher frequency, andpress the side to tune a lowerfrequency.
The SEEK functionsearches up and down from thecurrent frequency to find a stationwith a strong signal. To activate it,press the or side of theSEEK bar, then release it.On models with in-dash CD changer,press the or side of theSEEK bar until you hear a beep, thenrelease it.
The SCAN functionsamples all stations with strongsignals on the selected band. Toactivate it, press the SCAN button,then release it. You will see SCAN inthe display. The system will scan fora station with a strong signal. Whenit finds one, it will stop and play thatstation for about 5 seconds.
On models with in-dash CD changer
On models with in-dash CD changer
Except for models with in-dash CDchanger
On models with in-dash CD changer
Except for models with in-dash CDchanger
CONTINUED
Playing the Radio
To Play the Radio
To Select a Station
TUNE, SEEK, SCAN,AUTO SELECT
TUNE
SEEK
SCAN
Features
93
-
-
Press the A. SEL button. ‘‘A.SEL’’flashes in the display, and the systemgoes into scan mode for severalseconds. It stores the frequencies ofsix AM, and twelve FM stations inthe preset buttons.
You will see a ‘‘0’’ displayed afterpressing a preset button if AutoSelect cannot find a strong stationfor every preset button.
If you do not like the stations AutoSelect has stored, you can storeother frequencies on the presetbuttons as previously described.
press theA. SEL button. This restores thepresets you originally set.
If you aretraveling far from home and can nolonger receive your preset stations,you can use the auto select feature tofind stations in the local area.
To select a different presetfrequency, you can also use thePreset CALL bar. Press the ‘‘ ’’side of the bar to select thefrequency stored in the next presetbutton, and press the ‘‘ ’’ side toselect the frequency in the previouspreset button.
The preset frequencies will be lostif your vehicle’s battery goes dead,is disconnected, or the radio fuseis removed.
If you do nothing, the system willthen scan for the next strong stationand play it for 5 seconds. When itplays a station that you want to listento, press the SCAN button again.
Each preset button canstore one frequency on AM, and twofrequencies on FM.
Repeat steps 1 through 3 to store atotal of six stations on AM andtwelve stations on FM.
Pick a preset button, and hold ituntil you hear a beep.
Use the TUNE, SEEK, or SCANfunction to tune the radio to adesired station.
Select the desired band, AM orFM. FM1 and FM2 let you storetwo frequencies with each presetbutton.
1.
2.
3.
4.
To turn off Auto Select,
On models with in-dash CD changer
Playing the Radio
AUTO SELECT
Preset
94
-
-
-
-
CONTINUED
Adjust the Balance, or side-to-side strength of the sound.
Adjust the Fader, or thefront-to-back strength of the sound.
Adjust the Treble in thesound.
Adjust the Bass in the sound.
Press the SOUND (TUNE) knob orSOUND button repeatedly to displaythe Bass (BAS), Treble (TRE),Balance (BAL), and Fader (FAD)settings. Each mode is shown in thedisplay as it changes.
Turn the SOUND (TUNE) knob toadjust the setting to your liking.
Turn the Volume knob to adjust thesetting to your liking.
The displayed number shows youthe current setting. When the levelreaches the center, you will see a ‘‘C’’in the display. The system will returnto the audio display about 5 secondsafter you stop adjusting a mode.
The level gauge on the display alsoshows you the range. As you adjust amode, you will hear a beep wheneverthe adjustment level reaches thecenter (C), maximum, and minimumof its range.
Except for models with in-dash CDchanger
On models with in-dash CD changer
On all models
On models with in-dash CD changer
Playing the Radio
Adjusting the SoundBAL
FAD
TRE
BAS
Features
95
On models with in-dash CD changer On models with in-dash CD changer
You can display the sound withspectroscopic analysis. There arefive modes of display; Peak-Hold,Normal, Aurora, Level and Off. Eachtime you press and release the DISPbutton, the mode changes from P.HOLD to NORMAL to AURORA toLEVEL, then to OFF. You see theselected mode in the display forabout 5 seconds as it changes.
You can use the instrument panelbrightness control knob to adjust theillumination of the audio system (seepage ). The audio systemilluminates when the parking lightsare on, even if the radio is turned off.
You can also select the reducedbrightness in the display when theparking lights are on. Press and holdthe DISP button for about 5 secondsuntil you hear a beep to change thebrightness. Press and hold thisbutton again for about 5 secondsuntil you hear a beep to return to thefull brightness.
63
Playing the Radio
Spectroscopic Analysis Display brightnessAudio System Lighting
96
How well the radio receives stationsis dependent on many factors, suchas the distance from the station’stransmitter, nearby large objects,and atmospheric conditions.
The radio can receive the completeAM and FM bands.Those bands cover these frequen-cies:
AM band: 530 to 1,710 kilohertzFM band: 87.7 to 107.9 megahertz
Driving very near the transmitter ofa station that is broadcasting on afrequency close to the frequency ofthe station you are listening to canalso affect your radio’s reception.You may temporarily hear bothstations, or hear only the station youare close to.
A radio station’s signal gets weakeras you get farther away from itstransmitter. If you are listening to anAM station, you will notice the soundvolume becoming weaker and thestation drifting in and out. If you arelistening to an FM station, you willsee the stereo indicator flickering offand on as the signal weakens.Eventually, the stereo indicator willgo off and the sound will fadecompletely as you get out of range ofthe station’s signal.
Radio stations on the AM band areassigned frequencies at least tenkilohertz apart (530, 540, 550).Stations on the FM band areassigned frequencies at least 0.2megahertz apart (87.9, 88.1, 88.3).
Stations must use these exactfrequencies. It is fairly common forstations to round-off the frequency intheir advertising, so your radio coulddisplay a frequency of 100.9 eventhough the announcer may identifythe station as ‘‘FM101.’’
CONTINUED
Radio Reception
Radio ReceptionRadio Frequencies
Features
97
Radio signals, especially on the FMband, are deflected by large objectssuch as buildings and hills. Yourradio then receives both the directsignal from the station’s transmitter,and the deflected signal. This causesthe sound to distort or flutter. This isa main cause of poor radio receptionin city driving.
Radio reception can be affected byatmospheric conditions such asthunderstorms, high humidity, andeven sunspots. You may be able toreceive a distant radio station oneday and not receive it the next daybecause of a change in conditions.
Electrical interference from passingvehicles and stationary sources cancause temporary reception problems.
As required by the FCC:Changes or modifications not expresslyapproved by the party responsible forcompliance could void the user’sauthority to operate the equipment.
Radio Reception
98
-+
Playing a DiscF
eatures
99
AM/FM BUTTON
POWER/VOLUMEKNOB
DX model
CD/TAPE BUTTON RANDOM BUTTON
REPEATBUTTON
DISC BUTTONDISC BUTTON
SEEK/SKIP BAR
POWER/VOLUMEKNOB
AM/FMBUTTON
CD BUTTON
CD SLOT
REPEAT INDICATOR
RANDOM BUTTON
EJECTBUTTON
REPEAT BUTTON
RANDOM INDICATOR
SEEK/ SKIP BAR
LOAD BUTTON
LOADED DISCNUMBER
FOLDER INDICATOR/NUMBER
FILEINDICATOR/NUMBERDISC SLOT
DISC LOADINDICATOR
DISPLAYBUTTON
SEEK/SKIPBAR
CDBUTTON
DISCNUMBER
RANDOMBUTTON
FOLDERBAR
POWER/VOLUME KNOB
RANDOM INDICATOR
REPEATINDICATOR
TITLE BUTTON
EJECTBUTTON
RREPEAT BUTTON/SCAN BUTTON
MP3 INDICATOR
Audio System with In-dash CD ChangerU.S.: Special Edition modelsCanada: REVERB, Si-GA models
U.S.: Value Package, HX, LX, EX modelsCanada: DX Special Edition, LX, Si-G models
-
-
-
-
On models with in-dash CD changer
On models with CD player
Optional on DX model The in-dash CD changer can alsoplay CD-Rs and CD-RWscompressed in MP3 standard. Whenplaying a disc in MP3, you will see‘‘MP3’’ in the display. You can selecta folder or track up to .
Video CDs and DVD discs will notwork in this unit.
The specifications of the compatibleMP3 file are:
You operate the CD player/CDchanger with the same controls usedfor the radio. To select the CDplayer/CD changer, press the CDbutton. You will see ‘‘CD’’ in thedisplay. The number of the trackplaying is shown in the display. Withthe in-dash CD changer, the disc andtrack numbers are displayed. Thesystem will continuously play a discuntil you change modes.
To load or play discs, the ignitionswitch must be in the ACCESSORY(I) or ON (II) position.
Sampling frequency: 32/44.1/48kHzBit rate: 32/40/48/56/64/80/96/112/128/160/192/224/256/320 kbpsCompatible with variable bit rateand multi-sessionMaximum layers(including ROOT): 8 layers
While playing a disc, you can see theplaying time in the display bycancelling the clock display (seepage ).
Insert a CD into the CD slot. Thedrive will pull the CD in the rest ofthe way to play it. When the systemreaches the end of the disc, it willreturn to the beginning and play thedisc again.
You can also play 3-inch (8-cm) discswithout using an adapter ring.
To play the radio when a disc isplaying, press the AM/FM button.Press the CD button again to switchback to the CD player.
255
116
To Play a Disc
Playing a Disc
100
Do not use discs with adhesive labels.The label can curl up and cause thedisc to jam in the unit.
On models with in-dash CD changer
Your vehicle’s in-dash CD changerhold up to six discs.
Press the LOAD button until youhear beep and see ‘‘LOAD’’ in thedisplay. To load only one disc,press and release the LOADbutton. The green disc loadindicator will come on.
The disc number for an emptyposition begins blinking.
You cannot load and play 3-inch(8-cm) discs in this unit.
When the disc load indicator turnsgreen and ‘‘LOAD’’ appears in thedisplay again, insert the next discin the slot. Do not try to insert adisc until ‘‘LOAD’’ appears. Youcould damage the audio unit.
Repeat this until all six positionsare loaded. If you are not loadingall six positions, the system beginsplaying the last disc loaded.
You can also load a disc into anempty position while a disc is playingby pressing the appropriate presetbutton. The system stops playing thecurrent disc and starts the loadingsequence. It plays the disc justloaded.
Insert the disc into the disc slotwhen the green disc load indicatorcomes on. Insert it only abouthalfway; the drive will pull it in therest of the way. You will see‘‘BUSY’’ in the display while thedisc load indicator turns red andblinks as the disc is loaded.
To play the tape when a CD isplaying, insert a tape in the player(optional). If a tape is in the player,press the TAPE button. Press theCD button again, to switch back tothe CD player.
If you turn the system off while a CDis playing, either with the Power/Volume knob or by turning off theignition switch, the disc will stay inthe drive. When you turn the systemback on, the CD will begin playingwhere it left off.
1.
2.
3.
4.
5.
CONTINUED
Loading Discs in the In-dash CDChanger
Playing a DiscF
eatures
101
In MP3 mode with In-dash CD Changer
With In-dash CD Changer
When you press the TITLE buttonwhile playing a disc in MP3, thedisplay shows the first 13 charactersof the current folder or file name forabout 5 seconds, then automaticallyreturns to the normal display.
With the folder or file name, you willsee the FOLDER or FILE indicatorin the display.
Each time you press the TITLEbutton, the display mode changesfrom File Name display to FolderName display, then to Normaldisplay.
If the folder or file name has morethan 13 characters and the name isdisplayed, press and hold the TITLEbutton until you hear a beep. Thedisplay will show the next 13characters for about 5 seconds. To
see all characters of the folder or filename, repeat this step.
If you press the TITLE button whenthe last character(s) is displayed,you hear two beeps, then the displayshows the first 13 characters again.
You will also see the folder or filename in the following conditions:
When the folder or the file ischanged.
When you change the audio modeto play discs in MP3 and thesystem begins to play.
When you insert a disc and thesystem begins to play.
You can use the SEEK/SKIP barwhile a disc is playing to selectpassages and change tracks (files inMP3 mode).
To select a different disc, press theappropriate preset button (1 to 6). Ifyou select an empty position, thesystem will go into the loadingsequence (see page ).
In MP3 mode, use the FOLDER barto select folders in the disc and usethe SEEK/SKIP bar to change files.
101
Folder Name and File Name DisplayFunction
To Change or Select Tracks/Files
Playing a Disc
102
--
-
-
Each time youpress and release the /
side of the SEEK/SKIP bar,the player skips forward to thebeginning of the next track (file inMP3 mode). Press and release the
/ side, to skip backwardto the beginning of the current track.Press it again to skip to thebeginning of the previous track.
To move rapidly within a track, pressand hold the / or /
side of the SEEK/SKIP bar.
You will see CUE or REW in thedisplay while moving.
While moving forward or backward,the time display changes to thetrack/file playing time. Afterreleasing the bar, the display goesback to the time display.
Toselect a different folder, press andrelease the ‘‘ ’’ side of theFOLDER bar to move the beginningof the next folder. Press and releasethe ‘‘ ’’ side to move thebeginning of the current folder.Press and release it again to skip tothe beginning of the previous folder.
To continuously replaya track (file in MP3 mode), press andrelease the RPT button. You will seeRPT in the display. Press the RPTbutton again to turn it off. With thein-dash CD changer, press the RPTbutton two or three times dependingon the selected mode to return tonormal playing.
Pressing either side of the SEEK/SKIP bar or selecting a different discwith a preset button also turns offthe repeat feature.
This feature,when activated, replays all the tracks(all files in each folder in MP3 mode)on the selected disc in the order theyare recorded on the disc. To activatethe disc repeat feature, select theDisc-Repeat mode by pressing theRPT button repeatedly. You will seeD-RPT in the display. The systemcontinuously replays the current disc.Press the RPT button again to turn itoff. Pressing the RDM button orselecting a different disc with apreset button also turns off therepeat feature.
Except for models with in-dash CDchanger
On models with in-dash CD changer
In MP3 mode with In-dash CD Changer With In-dash CD Changer
With In-dash CD Changer
CONTINUED
SEEK/SKIPFOLDER SELECTION
REPEAT (TRACK/FILEREPEAT)
DISC-REPEAT
Playing a DiscF
eatures
103
-
-
-In MP3 mode with In-dash CD Changer
In CD mode with In-dash CD Changer
In MP3 mode with In-dash CD Changer
With In-dash CD Changer
In MP3 mode with In-dash CD ChangerThis feature,
when activated, replays all the fileson the selected folder in the orderthey are compressed in MP3. Toactivate Folder Repeat mode, pressthe RPT button. You will see F-RPTin the display. The systemcontinuously replays the currentfolder. Press the RPT button again toturn it off. Pressing the RDM button,selecting a different disc with apreset button, or selecting a differentfolder with the FOLDER bar alsoturns off the repeat feature.
This feature plays thetracks (all files in each folder in MP3mode) within a disc in random order.To activate Random Play, press andrelease the RDM button. In MP3mode, press the RDM button twiceto select Within a Disc Random Play.You will see RDM in the display.Press the RDM button again toreturn to normal play.
Selecting a different disc with apreset button also turns off therandom feature.
Thisfeature, when activated, plays thefiles within a folder in random order,rather than in the order they arecompressed in MP3. To activateFolder Random play, press the RDMbutton. You will see F-RDM in thedisplay. The system will then selectand play files randomly. Thiscontinues until you deactivate FolderRandom Play by pressing the RDMbutton again, or you select adifferent disc with a preset button ora different folder with the FOLDERbar.
Each time you press and release theRDM button, the mode changesfrom Folder Random Play to Withina Disc Random Play, then to normalplaying.
Each time you press and release theRPT button, the mode changes fromFile Repeat to Folder Repeat to DiscRepeat, then to normal playing.
Each time you press and release theRPT button, the mode changes fromTrack Repeat to Disc Repeat, then tonormal playing.
FOLDER-REPEAT
RANDOM (Random within aDisc)
FOLDER-RANDOM
Playing a Disc
104
- -In CD mode with In-dash CD Changer In MP3 mode with In-dash CD Changer
Except for models with in-dash CDchanger
The SCAN functionsamples all the tracks on theselected disc in the order they arerecorded on the disc. To activate theScan feature, press and hold theSCAN button until you hear a beep.You will see SCAN in the display.You will get a 10 second sampling ofeach track on the selected disc.Press the SCAN button again to getout of the system and play the lasttrack sampled.
Pressing either side of the SEEK/SKIP bar or selecting a different discwith a preset button also turns offthe scan feature.
This feature, whenactivated, samples all the files in theselected folder in the order they arecompressed in MP3. To activate theFolder Scan feature, press and holdthe SCAN button until you hear abeep. You will see F-SCAN in thedisplay. The system will then playthe first file for about 10 seconds. Ifyou do nothing, the system will thenplay the following files for 10seconds each. When it plays a filethat you want to continue listening to,press the SCAN button again.
Pressing either side of the SEEK/SKIP bar, selecting a different discwith a preset button, or a differentfolder with the FOLDER bar alsoturns off the scan feature.
Press the eject button ( ) toremove the CD. If you eject the CD,but do not remove it from the slot,the system will automatically reloadthe CD after 15 seconds and put it inpause mode. To begin playing, pressthe CD button.
Press the AM/FM button to switchto the radio while a CD is playing. Toplay the CD, press the CD button.
If a tape is in the optional tape player,press the TAPE button to switch tothe tape while a CD is playing. Pressthe CD button again to switch backto the CD player.
CONTINUED
SCAN F-SCANTo Stop Playing a Disc
Playing a DiscF
eatures
105
On models with in-dash CD changer
On models with in-dash CD changerPress the FM/AM button to switchto the radio while a disc is playing.To play the disc, press the CD button.
If you turn the system off while adisc is playing, either with thePower/Volume knob or by turningoff the ignition switch, the disc willstay in the drive. When you turn thesystem back on, the disc will beginplaying where it left off.
To remove the disc currently in play,press the eject ( ) button. Whena disc is removed from a slot, thesystem automatically begins the loadsequence so you can load anotherdisc in that position. If you do notremove the disc from the changerwithin 15 seconds, the systemreturns to the previous mode (FM/AM). The disc will reload into thesystem and will remain in a pausemode.
To remove a different disc from thechanger, first select it with theappropriate preset button. When thatdisc begins playing, press the ejectbutton. Continue pressing the ejectbutton to remove all the discs fromthe changer.
You can also eject discs when theignition switch is off. The disc thatwas last selected is ejected first.
Playing a Disc
Removing Discs from the In-dash CDChanger
106
- +
-+
On models with in-dash CD changer
Except for models with in-dash CDchanger
On models with in-dash CD changer
Except for models with in-dash CDchanger
The auxiliary input jack is on theaudio panel. The system will acceptauxiliary input from standard audioaccessories.
When the appropriate audio unit isconnected with the auxiliary inputjack, press the AUX button to selectthe unit.
See pages and forinformation on the error messages.
If you find any problem with thisaudio system, take the vehicle toyour dealer.
For information on how to handleand protect discs, see page .
If you select an empty slot in themagazine, the changer will searchfor the next available disc to load andplay.
An optional six disc CD changer isavailable for your vehicle. This discchanger uses the same controls usedfor the in-dash CD player or theradio.
Load the desired CDs in themagazine, and load the magazine inthe changer according to theinstructions that came with the unit.
To select the CD changer, press theCD button. The disc and tracknumbers will be displayed. To selecta different disc, use the preset 5(DISC ) or the preset 6 (DISC )button. To select the previous disc,press the preset 5 (DISC ), or thepreset 6 (DISC ) to select the nextdisc in sequence.
109 110
108
Playing a Disc
Auxiliary Input Jack
Audio System Malfunction
Protecting Discs
Operating the Optional CDChanger
Features
107
When using CD-R or CD-RW (onlywith in-dash CD changer) discs,use only high quality CDs labeledfor audio use.
When recording a CD-R orCD-RW (only with in-dash CDchanger), the recording must beclosed for it to be used by thesystem.
CD-RW discs will not work in thisunit.
Play only standard round CDs.Odd-shaped CDs may jam in thedrive or cause other problems.
Handle your CDs properly toprevent damage and skipping.
Never try to insert foreign objects inthe system or the magazine.
When a disc is not being played,store it in its case to protect it fromdust and other contamination. Toprevent warpage, keep discs out ofdirect sunlight and extreme heat.
A new disc may be rough on theinner and outer edges. The smallplastic pieces causing this roughnesscan flake off and fall on therecording surface of the disc,causing skipping or other problems.Remove these pieces by rubbing theinner and outer edges with the sideof a pencil or pen.
To clean a disc, use a clean soft cloth.Wipe across the disc from the centerto the outside edge.
Handle a disc by its edges; nevertouch either surface. Do not placestabilizer rings or labels on the disc.These, along with contaminationfrom fingerprints, liquids, and felt-tippens, can cause the disc to not playproperly, or possibly jam in the drive.
You can also play 3-inch (8-cm)discs without using an adapterring.
Except for models with in-dash CDchanger
Except for models with in-dash CDchanger
General Information
Protecting Discs
Protecting Your Discs
108
Error Message Cause SolutionIf you see an error message in thedisplay while playing a disc, find thecause in the chart to the right. If youcannot clear the error message, takeyour vehicle to your dealer.
Except for models with in-dash CDchanger
FOCUS Error
Mechanical Error
High temperature
Press the EJECT button and pull out the disc.Check if it is inserted correctly in the discplayer.Make sure the disc is not scratched or damaged.Press the EJECT button and pull out the disc.Check the disc for damage or deformation.If the disc cannot be pulled out, or the errormessage does not disappear after the disc isejected, see your dealer.Will disappear when the temperature returns tonormal.
CD Player Error MessagesF
eatures
109
Error Message SolutionCauseExcept for models with in-dash CDchangerIf you see an error message in thedisplay while playing a disc, find thecause in the chart to the right. If youcannot clear the error message, takeyour vehicle to your dealer.
Press the magazine eject button and pull it out.If the message does not disappear or themagazine cannot be pulled out, see your dealer.Insert disc.
Press the magazine eject button and pull it out,check for an error message, and insert themagazine again. If the message does notdisappear or the magazine cannot be pulled out,see your dealer.Will disappear when the temperature returns tonormal.Insert disc magazine.
FOCUS Error
No disc in the discmagazine
Mechanical Error
High temperature
No disc magazine in thedisc changer
CD Changer Error Messages
110
Playing a Tape (Optional)F
eatures
111
FF BUTTONREW BUTTON
CD/TAPE BUTTON
AM/FM BUTTON
SKIP BAR
CD/TAPE BUTTON
SKIP BAR
REW BUTTON
FF BUTTON
PLAY/PROG BUTTON
REPEAT INDICATOR
DOLBY INDICATOR
AM/FM BUTTON
PLAY/PROG BUTTONDX model
REPEAT BUTTON
POWER/VOLUME KNOBNOISE REDUCTION BUTTON
DOLBY INDICATOR
REPEAT BUTTON
NOISE REDUCTION BUTTON
POWER/VOLUME KNOB
U.S.: Value Package, HX, LX, EX modelsCanada:DX Special Edition, LX, Si- G models
-
-
▲
*
*
To switch to the radio or CD playerwhile a tape is playing, press theAM/FM or CD/TAPE button. Tochange back to the tape player, pressthe CD/TAPE button.
To rewind the tape,push the REW button. You will seeREW in the display. To fast forwardthe tape, push the FF button. Youwill see FF displayed. Press the FF,REW, or PLAY/PROG button totake the system out of rewind or fastforward.
Press button to findthe beginning of the current song orpassage. Press button to findthe beginning of the next song orpassage. When the system reachesthe beginning of a song or passage, itbegins to play it.
The ignition switch must be inACCESSORY (I) or ON (II). Makesure the open side of the tape isfacing right, then insert the tapemost of the way into the slot. Thesystem will pull the tape in the restof the way, and begin to play it.
The tape direction indicator willcome on to show you which side ofthe tape is playing. The indicatesthe side you inserted upward is nowplaying. If you want to play the otherside, press the PLAY/PROG button.When the player reaches the end ofthe tape, it will automatically reversedirection and play the other side.
Dolby noise reduction turns onwhen you insert a tape. The
indicator will come on in thedisplay. If the tape was not recordedin Dolby, turn it off by pressing theNR button. Dolby remains off untilyou press the NR button again.
To remove the tape, press the ejectbutton on the tape player. If youwant to turn the player off, press thePower/Volume knob or turn off theignition. The tape will remain in thedrive. When you turn the systemback on, the tape will begin playingwhere it left off.
Tape player is optional except formodels with in-dash CD changer.
Dolby noise reduction is manufactured underlicense from Dolby Laboratories LicensingCorporation. ‘‘DOLBY’’ and the double-D symbol
are trademarks of Dolby LaboratoriesLicensing Corporation.
To Play a Tape
To Stop Playing a Tape
Tape Search FunctionsFF/REW
SKIP
Playing a Tape (Optional)
112
- Press the RPT buttonto continuously play a song orpassage. You will see RPT displayed.The track will repeat until you pressthe RPT button again.
The SKIP and REPEATfunctions use silent periods on thetape to find the end of a song orpassage. These features may notwork if there is almost no gapbetween selections, a high noiselevel, or a silent period in the middleof a selection.
The tape player picks up dirt andoxides from the tape. Thiscontamination builds up over timeand causes the sound quality todegrade. To prevent this, you shouldclean the player after every 30 hoursof use.
If you do not clean the tape playerregularly, it may eventually becomeimpossible to remove thecontamination with a normalcleaning kit. Your dealer has acleaning kit available.
Use 100-minute or shorter tapes.Tapes longer than that may break orjam the drive.
If the tape is loose, tighten it byturning the hub with a pencil or yourfinger. If the label is peeling off,remove it or it could cause thecassette to jam in the player. Nevertry to insert a warped or damaged
cassette in the player.
Store tapes in their cases to protectthem from dust and moisture. Neverplace tapes where they will beexposed to direct sunlight, high heat,or high humidity. If a tape is exposedto extreme heat or cold, let it reach amoderate temperature beforeinserting it into the player.
Never try to insert foreign objectinto the tape player.
REPEAT Caring for the Tape and Player
Playing a Tape (Optional)F
eatures
113
NOTE:
Your vehicle’s audio system willdisable itself if it is disconnectedfrom electrical power for any reason.To make it work again, the usermust enter a specific five-digit codein the Preset buttons. Because thereare hundreds of numbercombinations possible from the five-digits, making the system workwithout knowing the exact code isnearly impossible.
You should have received a card thatlists your audio system’s code andserial numbers. It is best to store thiscard in a safe place at home. Inaddition, you should write the audiosystem’s serial number in thisOwner’s Manual.
If you lose the card, you must obtainthe code number from a dealer. To
do this, you will need the system’sserial number.
If your vehicle’s battery isdisconnected or goes dead, or theradio fuse is removed, the audiosystem will disable itself. If thishappens, you will see ‘‘ ’’(except for models within-dash CD changer)/‘‘CODE’’(on models with in-dash CDchanger) in the frequency displaythe next time you turn on the system.Use the preset buttons to enter thefive-digit code. The code is on theradio code card included in yourOwner’s Manual kit. When it isentered correctly, the radio will startplaying.
If you make a mistake entering thecode, do not start over; complete thefive-digit sequence, then enter thecorrect code. You have ten tries toenter the correct code. If you areunsuccessful in ten attempts, you
must then leave the system on for 1hour before trying again.
You will have to store your favoritestations in the preset buttons afterthe system begins working. Youroriginal settings were lost when thepower was disconnected.
Standard for Value Package, HX, LX, EXand Special Edition models in the U.S.,and DX Special Edition, REVERB, LXand Si models in Canada
Radio Theft Protection
114
CONTINUED
Setting the ClockF
eatures
115
DX model
CLOCK BUTTON
RESET BUTTON
MINUTE BUTTONHOUR BUTTON
CLOCK BUTTON
HOUR BUTTONMINUTE BUTTON
RESET BUTTON
CLOCKBUTTON
CLOCK DISPLAY
HOURBUTTON
MINUTEBUTTON
RESETBUTTON
U.S.: Special Edition modelsCanada: REVERB, Si-GA models
U.S.: Value Package, HX, LX, EX modelsCanada: DX Special Edition, LX, Si-G models
If your vehicle’s battery isdisconnected or goes dead, you willneed to set the clock.
To set the time, press the CLOCK(SCAN/RPT, AUX) button until youhear a beep, then release the button.The displayed time begins to blink.
Change the hours by pressing the H(preset 4) button until the numbersadvance to the desired time. Changethe minutes by pressing the M(preset 5) button until the numbersadvance to the desired time.
Press the CLOCK (SCAN/RPT,AUX) button again to enter the settime. On models with in-dash CDchanger, press the CLOCK buttonuntil you hear a beep.
You can quickly set the time to thenearest hour. If the displayed time isbefore the half hour, pressing theCLOCK (SCAN/RPT, AUX) buttonuntil you hear a beep, then pressingthe R (preset 6) button sets the clockback to the previous hour. If thedisplayed time is after the half hour,the clock sets forward to thebeginning of the next hour.
For example: 1:06 will reset to 1:001:52 will reset to 2:00
You can set the time only when theclock is displayed.
To set the hours, press and hold theCLOCK button, then press the H(preset 4) button until the numbersadvance to the desired time. To setthe minutes, press and hold theCLOCK button, then press the M(preset 5) button until the numbers
advance to the desired time.
To quickly set the time to thenearest hour, press and hold theCLOCK button, then press the R(preset 6) button.
To turn off the clock display, pressthe CLOCK (AUX) button until youhear a beep, then press the Preset 3(Clock Off) button. The displayedtime will be turned off.
To show the time again, press theCLOCK (AUX) button again untilyou hear a beep.
On models with in-dash CD player/changer
On models without in-dash CD player/changer
On models with in-dash CD changer
Setting the Clock
Cancelling Clock Display
116
If equippedCruise control allows you to maintaina set speed above 25 mph (40 km/h)without keeping your foot on theaccelerator pedal. It should be usedfor cruising on straight, openhighways. It is not recommended forcity driving, winding roads, slipperyroads, heavy rain, or bad weather.
Accelerate to the desired cruisingspeed above 25 mph (40 km/h).
Press and release the SET/decelbutton on the steering wheel. Theindicator on the instrument panelcomes on to show the system isnow activated.
Push in the CRUISE button. Theindicator will come on.
1.
2.
3.
CONTINUED
Cruise Control
Using Cruise Control
Features
117
CANCEL BUTTON
RESUME/accelBUTTON
SET/decelBUTTON
CRUISE BUTTON
Improper use of the cruisecontrol can lead to a crash.
Use the cruise control onlywhen traveling on openhighways in good weather.
You can decrease the set cruisingspeed in any of these ways:
To slow down in very smallamounts, tap the SET/decelbutton. Each time you do this,your vehicle slows down about 1mph (1.6 km/h).
Press and hold the SET/decelbutton. Release the button whenyou reach the desired speed.
You can increase the set cruisingspeed in any of these ways:
Press and hold the RESUME/accel button. When you reach thedesired cruising speed, release thebutton.
Tap the brake or clutch pedallightly with your foot. TheCRUISE CONTROL indicator onthe instrument panel goes out.When the vehicle slows to thedesired speed, press the SET/decel button.
Cruise control may not hold the setspeed when you are going up anddown hills. If your speed increasesgoing down a hill, use the brakes toslow down. This will cancel cruisecontrol. To resume the set speed,press the RESUME/accel button.The CRUISE CONTROL indicatoron the instrument panel will comeback on.
When climbing a steep hill, theautomatic transmission maydownshift to hold the set speed.
Push on the accelerator pedal untilyou reach the desired cruisingspeed, and press the SET/decelbutton.
To increase the speed in verysmall amounts, tap the RESUME/accel button. Each time you dothis, your vehicle speeds up about1 mph (1.6 km/h).
Changing the Set Speed
Cruise Control
118
Resting your foot on the brake orclutch pedal causes the cruisecontrol to cancel.
Even with cruise control turned on,you can still use the acceleratorpedal to speed up for passing. Aftercompleting the pass, take your footoff the accelerator pedal. The vehiclewill return to the set cruising speed.
When you push the CANCEL button,or tap the brake or clutch pedal, thesystem remembers the previouslyset cruising speed. To return to thatspeed, accelerate to above 25 mph(40 km/h) and then press andrelease the RESUME/accel button.The CRUISE CONTROL indicatorcomes on, and the vehicleaccelerates to the same cruisingspeed as before.
Tap the brake or clutch pedal.
Push the CANCEL button on thesteering wheel.
You can cancel cruise control in anyof these ways:
Push the CRUISE button.
Pressing the CRUISE button turnsthe system off and erases theprevious cruising speed.
Cruise Control
Resuming the Set SpeedCancelling Cruise Control
Features
119
120
Before you begin driving yourvehicle, you should know whatgasoline to use and how to check thelevels of important fluids. You alsoneed to know how to properly storeluggage or packages. Theinformation in this section will helpyou. If you plan to add anyaccessories to your vehicle, pleaseread the information in this sectionfirst.
.............................Break-in Period . 122.................Fuel Recommendation . 122
.........Service Station Procedures . 123....................................Refueling . 123
Opening and Closing................................the Hood . 124
...................................Oil Check . 125.............Engine Coolant Check . 126
...............................Fuel Economy . 127...Accessories and Modifications . 128
.............................Carrying Cargo . 130
Before DrivingB
eforeD
riving
121
Help assure your vehicle’s futurereliability and performance by payingextra attention to how you driveduring the first 600 miles (1,000 km).During this period:
Avoid full-throttle starts and rapidacceleration.
You should also follow theserecommendations with anoverhauled or exchanged engine, orwhen the brakes are replaced.
Avoid hard braking for the first200 miles (300 km).
Do not change the oil until thescheduled maintenance time.
Your vehicle is designed to operateon unleaded gasoline with a pumpoctane number of 86 or higher. Useof a lower octane gasoline can causea persistent, heavy metallic rappingnoise that can lead to engine damage.
We recommend using qualitygasoline containing detergentadditives that help prevent fuelsystem and engine deposits.
In addition, in order to maintain goodperformance, fuel economy, andemissions control, we stronglyrecommend, in areas where it isavailable, the use of gasoline thatdoes NOT contain manganese-basedfuel additives such as MMT.
Use of gasoline with these additivesmay adversely affect performance,and cause the malfunction indicatorlamp on your instrument panel tocome on. If this happens, contact
your authorized dealer for service.
Some gasoline today is blended withoxygenates such as ethanol orMTBE. Your vehicle is designed tooperate on oxygenated gasolinecontaining up to 10 percent ethanolby volume and up to 15 percentMTBE by volume. Do not usegasoline containing methanol.
If you notice any undesirableoperating symptoms, try anotherservice station or switch to anotherbrand of gasoline.
For further important fuel-relatedinformation, please refer to your
.
Break-in Period Fuel Recommendation
Quick Start Guide
Break-in Period, Fuel Recommendation
122
Park with the driver’s side of thevehicle closest to the servicestation pump.
Remove the fuel fill cap slowly.You may hear a hissing sound aspressure inside the tank escapes.Place the cap in the holder on thefuel fill door.
Stop filling the tank after the fuelnozzle automatically clicks off. Donot try to ‘‘top off’’ the tank. Leavesome room for the fuel to expandwith temperature changes.
Open the fuel fill door by pushingon the handle to the left of thedriver’s seat.
even though the tank is not full,there may be a problem with yourvehicle’s fuel vapor recoverysystem. The system helps keepfuel vapors from going into theatmosphere. Try filling at anotherpump. If this does not fix theproblem, consult your dealer.
1.
2.
3.
4.
CONTINUED
If the fuel nozzle keeps clicking off
Service Station Procedures
Refueling
Before
Driving
123
Push
HOLDER
FUEL FILL CAP
Gasoline is highly flammableand explosive. You can beburned or seriously injuredwhen handling fuel.
Stop the engine and keepheat, sparks, and flame away.Handle fuel only outdoors.Wipe up spills immediately.
If the hood latch handle movesstiffly, or if you can open the hoodwithout lifting the handle, themechanism should be cleaned andlubricated.
Put your fingers under the frontedge of the hood near the center.Slide your hand to the left untilyou feel the hood latch handle.Push this handle up to release it.Lift up the hood.
Screw the fuel fill cap back onuntil it clicks at least three times.If you do not properly tighten thecap, the Malfunction IndicatorLamp may come on (see page
).
Push the fuel fill door closed untilit latches.
Park the vehicle, and set theparking brake. Pull the hoodrelease handle located under thelower left corner of the dashboard.The hood will pop up slightly.
1. 2.
201
5.
6.
Opening and Closing the Hood
Service Station Procedures
124
HOODRELEASEHANDLE
LATCH
Remove the dipstick again, andcheck the level. It should bebetween the upper and lowermarks.
Wait a few minutes after turning theengine off before you check the oil.
Insert it all the way back in its tube.
If it is near or below the lower mark,see on page .
Pull the support rod out of its clipand insert the end into thedesignated hole in the hood.
To close the hood, lift it up slightlyto remove the support rod fromthe hole. Put the support rod backinto its holding clip. Lower thehood to about a foot (30 cm) abovethe fender, then let it drop. Makesure it is securely latched.
Remove the dipstick (orange loop).
Wipe off the dipstick with a cleancloth or paper towel.
3.
1.
2.
4.3.
159
Oil Check
Adding Engine Oil
Service Station ProceduresB
eforeD
riving
125
SUPPORT ROD
CLIP
UPPER MARK
LOWER MARKDIPSTICK
Look at the coolant level in theradiator reserve tank. Make sure it isbetween the MAX and MIN lines. Ifit is below the MIN line, see
on page forinformation on adding the propercoolant.
Refer toon page for information
about checking other items on yourvehicle.
162
152Engine Coolant Check
AddingEngine Coolant
Owner’s MaintenanceChecks
Service Station Procedures
126
MAX
MIN
RESERVETANK
Try to maintain a constant speed.Every time you slow down andspeed up, your vehicle uses extrafuel. Use the cruise control whenappropriate.
Combine several short trips intoone.
The air conditioning puts an extraload on the engine which makes ituse more fuel. Use the fresh-airventilation when possible.
an underinflated tirecauses more ‘‘rolling resistance,’’which uses more fuel.
The build-up of snow or mud onyour vehicle’s underside addsweight and rolling resistance.Frequent cleaning helps your fuelmileage and reduces the chance ofcorrosion.
Always maintain your vehicleaccording to the maintenanceschedule. See
(see page).
Always drive in the highest gearpossible.
Drive moderately. Rapidacceleration, abrupt cornering,and hard braking use more fuel.
152
For example,
Improving Fuel Economy
Owner’sMaintenance Checks
Fuel EconomyB
eforeD
riving
127
When properly installed, cellularphones, alarms, two-way radios, andlow-powered audio systems shouldnot interfere with your vehicle’scomputer controlled systems, suchas your airbags and anti-lock brakes.
Before installing any accessory:
Make sure the accessory does notobscure any lights, or interferewith proper vehicle operation orperformance.
Be sure electronic accessories donot overload electrical circuits(see page ) or interfere withproper operation.
Modifying your vehicle, or installingsome non-Honda accessories, canmake it unsafe. Before you make anymodifications or add any accessories,be sure to read the followinginformation.
Your dealer has Honda accessoriesthat allow you to personalize yourvehicle, or improve its performance.These accessories have beendesigned and approved for yourvehicle, and are covered by warranty.
Although non-Honda accessoriesmay fit on your vehicle, they may notmeet factory specifications, andcould adversely affect your vehicle’shandling and stability.
Before installing any electronicaccessory, have the installercontact your dealer for assistance.If possible, have your dealerinspect the final installation.
204
Accessories
Accessories and Modifications
128
Improper accessories ormodifications can affect yourvehicle’s handling, stability, andperformance, and cause acrash in which you can be hurtor killed.
Follow all instructions in thisowner’s manual regardingaccessories and modifications.
Some examples are:
Larger or smaller wheels and tirescan interfere with the operation ofyour vehicle’s anti-lock brakes andother systems.
Removing parts from your vehicle,or replacing components withnon-Honda components couldseriously affect your vehicle’shandling, stability, and reliability.
Non-Honda wheels, because theyare a universal design, can causeexcessive stress on suspensioncomponents.
Raising your vehicle with anon-Honda suspension kit canaffect the handling and stability.
Lowering your vehicle with anon-Honda suspension kit thatsignificantly reduces groundclearance can allow theundercarriage to hit speed bumpsor other raised objects, whichcould cause the airbags to deploy.
If you plan to modify your vehicle,consult your dealer.
Modifying your steering wheel orany other part of your vehicle’ssafety features can make thesystems ineffective.
Modifying Your Vehicle
Accessories and ModificationsB
eforeD
riving
129
*
*
*
Your vehicle has several convenientstorage areas:
However, carrying too much cargo,or improperly storing it, can affectyour vehicle’s handling, stability,stopping distance, and tires, andmake it unsafe. Before carrying anytype of cargo, be sure to read thefollowing pages.
Roof-rack (if installed)
Trunk, including the rear seatswhen folded down
Console compartmentDoor and seat-back pocketsGlove box
Carrying Cargo
130
TRUNK
GLOVE BOX
CONSOLE COMPARTMENT DOOR POCKET
SEAT-BACK POCKET
: If equipped
- ×
The maximum load for your vehicleis 850 lbs (395 kg). This figureincludes total weight of all occupants,cargo, and accessories.
Determine the combined weightof luggage and cargo being loadedon the vehicle. That weight maynot safely exceed the availablecargo and luggage load capacity inStep 4.
Steps for determining correct loadlimit:
Locate the statement, ‘‘thecombined weight of occupants andcargo should never exceed 850lbs’’ on your vehicle’s placard.[The placard is on the driver’sdoorjamb.]
Determine the combined weightof the driver and passengers thatwill be riding in your vehicle.
Subtract the combined weight ofthe driver and passengers from850 pounds or 395 kilograms.
In addition, the total weight of thevehicle, all passengers, accessories,and cargo must not exceed the GrossVehicle Weight Rating (GVWR) orthe Gross Axle Weight Rating(GAWR). Both are on a label on thedriver’s doorjamb.
The resulting figure equals theavailable amount of cargo andluggage load capacity. Forexample, if the maximum load is850 lbs and there will be five 150 lb.passengers in your vehicle, theamount of available cargo andluggage load capacity is 100 lbs.(850 750 (5 150) = 100 lbs.)
1.
2.
3.
4.
5.
Carrying Cargo
Load Limits
Before
Driving
131
Overloading or improperloading can affect handling andstability and cause a crash inwhich you can be hurt or killed.
Follow all load limits and otherloading guidelines in thismanual.
If you carry large items thatprevent you from closing the trunklid, exhaust gas can enter thepassenger area. To avoid thepossibility of
, follow the instructionson page .
If you fold down the back seat, tiedown items that could be thrownabout the vehicle during a crash orsudden stop.
Distribute cargo evenly on thefloor of the cargo area, placing theheaviest items on the bottom andas far forward as possible.
Store or secure all items that couldbe thrown around and hurtsomeone during a crash.
Do not put any items on top of therear shelf. They can block yourview and be thrown around thevehicle during a crash.
Be sure items placed on the floorbehind the front seats cannot rollunder the seats and interfere withthe driver’s ability to operate thepedals or the seat.
Keep the glove box closed whiledriving. If it is open, a passengercould injure their knees during acrash or sudden stop.
If you use an accessory roof rack,the roof rack weight limit may belower. Refer to the information thatcame with your roof rack.
The cargo net can be used to helphold down items stored in the trunk.
If you carry any items on a roofrack, be sure the total weight ofthe rack and the items does notexceed the maximum allowableweight. Please contact your dealerfor further information.
45
If equipped
Carrying Cargo
carbon monoxidepoisoning
Carrying Cargo in the Trunk or ona Roof Rack
Carrying Items in the PassengerCompartment
Cargo Net
132
This section gives you tips onstarting the engine under variousconditions, and how to operate themanual and automatic transmissions.It also includes importantinformation on parking your vehicle,and the braking system.
........................Preparing to Drive . 134.......................Starting the Engine . 135
...................Manual Transmission . 136..............Automatic Transmission . 138
.Automatic Transmission (CVT) . 142...........................................Parking . 145
.............................Braking System . 146...............Anti-lock Brakes (ABS) . 147
...........................Towing a Trailer . 148
DrivingD
riving
133
Fasten your seat belt. Check thatyour passengers have fastenedtheir seat belts (see page ).
Make sure the doors are securelyclosed and locked.
Check the steering wheeladjustment (see page ).
Check the adjustment of theinside and outside mirrors (seepage ).
Check that any items you may becarrying are stored properly orfastened down securely.
Check the seat adjustment (seepage ).
Make sure all windows, mirrors,and outside lights are clean andunobstructed. Remove frost, snow,or ice.
You should do the following checksand adjustments before you driveyour vehicle.
Check that the hood is fully closed.
Check that the trunk is fullyclosed.
Visually check the tires. If a tirelooks low, use a gauge to check itspressure.
When you start the engine, checkthe gauges and indicators in theinstrument panel (see page ).
1.
2.
14
3.
4.
5.
6.
7.
8.
9.
11.
10.
80
73
65
51
Preparing to Drive
134
Apply the parking brake.
In cold weather, turn off allelectrical accessories to reducethe drain on the battery.
Push the clutch pedal down all theway. START (III) does notfunction unless the clutch pedal isdepressed.
Without touching the acceleratorpedal, turn the ignition key to theSTART (III) position. Do not holdthe key in START for more than15 seconds at a time. If the enginedoes not start right away, pausefor at least 10 seconds beforetrying again.
Make sure the shift lever is inPark. Press on the brake pedal.
If the engine fails to start, pressthe accelerator pedal all the waydown and hold it there whilestarting to clear flooding. If theengine still does not start, returnto step 5.
If the engine does not start within15 seconds, or starts but stallsright away, repeat step 4 with theaccelerator pedal pressed halfwaydown. If the engine starts, releasepressure on the accelerator pedalso the engine does not race.
5.
6.
1.
2.
3.
4.
Manual Transmission:
Automatic Transmission:
67
Starting the EngineD
riving
135
Immobilizer System
The engine is harder to start in coldweather. Also, the thinner air f ound ataltitudes above 8,000 f eet (2,400meters) adds to this problem.
The immobilizer system protects yourvehicle f rom thef t. If an improperly-coded key (or other device) is used, theengine’s f uel system is disabled. See
on page .
The manual transmission is syn-chronized in all forward gears forsmooth operation. It has a lockout soyou cannot shift directly from Fifthto Reverse. When shifting up ordown, make sure you push the clutchpedal down all the way, shift to thenext gear, and let the pedal upgradually. When you are not shifting,do not rest your foot on the clutchpedal. This can cause your clutch towear out faster.
Come to a full stop before you shiftinto Reverse. You can damage thetransmission by trying to shift intoReverse with the vehicle moving.Push down the clutch pedal, andpause for a few seconds beforeshifting into Reverse, or shift intoone of the forward gears for amoment. This stops the gears sothey won’t ‘‘grind.’’
When slowing down, you can getextra braking from the engine byshifting to a lower gear. This extrabraking can help you maintain a safespeed and prevent your brakes fromoverheating while going down asteep hill. Before downshifting,make sure the vehicle speed is lowenough that you will not activate theengine speed limiter in the lowergear. On all models except U.S. DXand Value Package, make sure theengine speed will not go into thetachometer’s red zone in the lowergear before downshifting.
Manual Transmission
136
Rapid slowing or speeding-upcan cause loss of control onslippery surfaces. If you crash,you can be injured.
Use extra care when driving onslippery surfaces.
If you exceed the maximum speedfor the gear you are in, you may feelthe engine cut in and out. This iscaused by a limiter in the engine’scomputer controls. The engine willrun normally when you reduce theengine speed by upshifting orslowing down.
Before downshifting, make sure thevehicle speed is low enough that youwill not activate the engine speedlimiter in the lower gear.
Drive in the highest gear that letsthe engine run and acceleratesmoothly. This will give you goodfuel economy and effectiveemissions control. The followingshift points are recommended:
Shift up
1st to 2nd2nd to 3rd3rd to 4th4th to 5th
Normal acceleration
15 mph (24 km/h)27 mph (43 km/h)39 mph (63 km/h)53 mph (85 km/h)
Before downshifting, make sure theengine will not go into thetachometer’s red zone.
If you exceed the maximum speedfor the gear you are in, the enginespeed will enter into the tachometer’sred zone. If this occurs, you may feelthe engine cut in and out. This iscaused by a limiter in the engine’scomputer controls. The engine willrun normally when you reduce theRPM below the red zone.
U.S. DX and Value Package modelsAll models except U.S. DX and ValuePackage
Engine Speed LimiterRecommended Shift Points
Manual TransmissionD
riving
137
These indicators on the instrumentpanel show which position the shiftlever is in.
The ‘‘D’’ indicator comes on for afew seconds when you turn theignition switch to ON (II). If itflashes while driving (in any shiftposition), it indicates a possibleproblem in the transmission. Avoidrapid acceleration and have the trans-mission checked by your dealer assoon as possible.
Automatic Transmission
Shift Lever Position Indicators
138
U.S.: DX, Value PackageU.S.: LX, EX, Special EditionCanada: LX, Si
Canada: DX,DX Speical Edition, REVERB
- -
CONTINUED
To shift from:P to R
R to PN to RD to 22 to DD to DD to ND to DN to DR to N
Do this:Press the brake pedal andpress the release button.
Press the release button.
Move the lever.
3
3
3
3
To shift from any position, pressfirmly on the brake pedal and pressthe release button on the front of theshift lever. You cannot shift out ofPark when the ignition switch is inthe LOCK (0) or ACCESSORY (I)position.
This position mechani-cally locks the transmission. UsePark whenever you are turning off orstarting the engine. To shift out ofPark, you must press on the brakepedal and have your foot off theaccelerator pedal. Press the releasebutton on the front of the shift leverto move it.
If you have done all of the above andstill cannot move the lever out ofPark, see onpage .
To avoid transmission damage, cometo a complete stop before shiftinginto Park. You must also press therelease button to shift into Park. Theshift lever must be in Park beforeyou can remove the key from theignition switch.
Press the brakepedal and press the release buttonon the front of the shift lever to shiftfrom Park to Reverse. To shift fromReverse to Neutral, come to acomplete stop and then shift. Pressthe release button before shiftinginto Reverse from Neutral.
141
Automatic Transmission
Shifting
Park (P)
Shift Lock Release
Reverse (R)
Driving
139
SHIFT LEVER
RELEASE BUTTON
-
-
-
-
If you exceed the maximum speedfor the gear you are in, the enginespeed will enter into the tachometer’sred zone. If this occurs, you may feelthe engine cut in and out. This iscaused by a limiter in the engine’scomputer controls. The engine willrun normally when you reduce theRPM below the red zone.
If you exceed the maximum speedfor the gear you are in, you may feelthe engine cut in and out. This iscaused by a limiter in the engine’scomputer controls. The engine willrun normally when you reduce theengine speed by upshifting orslowing down.
To help reduce wheel spin.
For starting out on a slipperysurface or in deep snow.
To increase engine braking whengoing down steep hills.
For more power when climbing.Use Second gear:
This position is similarto D, except only the first threegears are selected. Use D to provideengine braking when going down asteep hill. D can also keep thetransmission from cycling betweenthird and fourth gears in stop-and-godriving.
To shift to Second,press the release button on the frontof the shift lever. This position locksthe transmission in second gear. Itdoes not downshift to first gearwhen you come to a stop.
Use Neutral if youneed to restart a stalled engine, or ifit is necessary to stop briefly withthe engine idling. Shift to the Parkposition if you need to leave yourvehicle for any reason. Press on thebrake pedal when you are movingthe shift lever from Neutral toanother gear.
Use this position foryour normal driving. Thetransmission automatically selects asuitable gear for your vehicle speedand acceleration. You may notice thetransmission shifting up at higherspeeds when the engine is cold. Thishelps the engine warm up faster.
3
3
All models except U.S. DX and ValuePackage
U.S. DX and Value Package models
Automatic Transmission
Engine Speed LimiterDrive (D )
Second (2)
Neutral (N)
Drive (D)
3
140
Do this if pushing on the brake pedaland pressing the release button doesnot shift the transmission out ofpark:
Set the parking brake.
Remove the key from the ignitionswitch.
Push down on the key while youpress the release button on theshift lever and move the shift leverout of Park to Neutral.
Put a cloth on the edge of the shiftlock release slot cover. Using asmall flat-tipped screwdriver or a
metal fingernail file, carefully pryon the edge of the cover to removeit.
Insert the key in the shift lockrelease slot.
Remove the key from the shiftlock release slot, then install thecover. Make sure the notch on thecover is on the left side.Return the key to the ignitionswitch, press the brake pedal, andrestart the engine.
If you need to use the shift lockrelease, it means your vehicle isdeveloping a problem. Have itchecked by your dealer.
1.
2.
3.
4.
5.
6.
Automatic Transmission
Shift Lock Release
Driving
141
COVER
SHIFT LOCKRELEASE SLOT
RELEASE BUTTON
The continuously variabletransmission’s unique designprovides a smooth, constant flow ofpower. It is electronically controlledfor more precise operation andbetter fuel economy.
These indicators on the instrumentpanel show which position the shiftlever is in.
Avoid rapid acceleration and havethe transmission checked by yourdealer as soon as possible.
To shift from any position, pressfirmly on the brake pedal and pressthe release button on the front of theshift lever. You cannot shift out ofPark when the ignition switch is inthe LOCK (0) or ACCESSORY (I)position.
The ‘‘D’’ indicator comes on for afew seconds when you turn theignition switch to ON (II). If itflashes while driving (in any shiftposition), it indicates a possibleproblem in the transmission.
On HX model
Automatic Transmission (CVT)
Continuously VariableTransmission (CVT)
Shift Lever Position Indicators
Shifting
142
RELEASE BUTTON
SHIFT LEVER
-
-
-To shift from:P to R
R to PN to RS to LL to SS to DD to SD to NN to DR to N
Do this:Press the brake pedal andpress the release button.
Press the release button.
Move the lever.Use Neutral if you
need to restart a stalled engine, or ifit is necessary to stop briefly withthe engine idling. Shift to the Parkposition if you need to leave yourvehicle for any reason. Press on thebrake pedal when you are movingthe shift lever from Neutral toanother gear.
This position mechani-cally locks the transmission. UsePark whenever you are turning off orstarting the engine. To shift out ofPark, you must press on the brakepedal and have your foot off theaccelerator pedal. Press the releasebutton on the front of the shift leverto move it.
If you have done all of the above andstill cannot move the lever out ofPark, see onpage .
You must also press the releasebutton to shift into Park. To avoidtransmission damage, come to acomplete stop before shifting intoPark. The shift lever must be in Parkbefore you can remove the key fromthe ignition switch.
To shift to Reversefrom Park, see the explanation underPark. To shift to Reverse fromNeutral, come to a complete stopfirst. Press the release button beforeshifting into Reverse from Neutral.
141
CONTINUED
Automatic Transmission (CVT)
Neutral (N)
Park (P)
Shift Lock Release
Reverse (R)
Driving
143
- -
-
Use this position foryour normal driving. Thetransmission automatically adjusts tokeep the engine at the best speed fordriving conditions. To help theengine warm up faster, thetransmission will select ratios thatallow the engine to run at higherspeeds when it is cold.
To shift to Low, pressthe release button on the front of theshift lever. Use Low to get morepower when climbing, and formaximum engine braking whengoing down steep hills.
Selecting Secondshifts the transmission into a lowerrange of ratios for betteracceleration and increased enginebraking. Use Second when you aregoing down a steep hill, or in stop-and-go driving.
For faster acceleration when in D, Sor L, the transmission willautomatically ‘‘kick down’’ to a lowerrange of ratios by pushing theaccelerator pedal to the floor.
The CVT shifts automatically tomaintain proper engine speed in anyshift position.
When the vehicle reaches themaximum speed in any shift position,you may feel the engine cut in andout. This is caused by a limiter (112mph, 180 km/h) in the engine’scomputer controls. The engine willrun normally when you reduce thespeed to below the maximum.
Automatic Transmission (CVT)
Drive (D) Low (L) Maximum Allowable Speeds
Second (S)
144
If your vehicle has an automatictransmission, set the parking brakebefore you put the transmission inPark. This keeps the vehicle frommoving and putting pressure on theparking mechanism in thetransmission.
If the vehicle is facing uphill, turnthe front wheels away from thecurb. If you have a manualtransmission, put it in first gear.
If the vehicle is facing downhill,turn the front wheels toward thecurb. If you have a manualtransmission, put it in reverse gear.
Make sure the parking brake isfully released before driving away.Driving with the parking brakepartially set can overheat ordamage the rear brakes.
Always use the parking brake whenyou park your vehicle. Make surethe parking brake is set firmly oryour vehicle may roll if it is parkedon an incline.
Make sure the moonroof (ifequipped) and the windows areclosed.
Never park over dry leaves, tallgrass, or other flammablematerials. The hot three waycatalytic converter could causethese materials to catch on fire.
Lock the doors.
Place any packages, valuables, etc.,in the trunk or take them with you.
Turn off the lights.
Parking Tips
ParkingD
riving
145
Check the brakes after drivingthrough deep water. Apply thebrakes moderately to see if they feelnormal. If not, apply them gently andfrequently until they do. Be extracautious in your driving.
The hydraulic system that operatesthe brakes has two separate circuits.Each circuit works diagonally acrossthe vehicle (the left-front brake isconnected with the right-rear brake,etc.). If one circuit should develop aproblem, you will still have brakingat two wheels.
The front disc brakes on all modelshave audible brake wear indicators.
If the brake pads need replacing, youwill hear a distinctive, metallicscreeching sound when you applythe brake pedal. If you do not havethe brake pads replaced, they willscreech all the time. It is normal forthe brakes to occasionally squeal orsqueak when you apply them.
Your vehicle is equipped with frontdisc brakes. The brakes on the rearwheels are drum. A power assisthelps reduce the effort needed onthe brake pedal. The ABS (onmodels equipped) helps you retainsteering control when braking veryhard.
Resting your foot on the pedal keepsthe brakes applied lightly, builds upheat, and reduces their effectiveness.It also keeps your brake lights on allthe time, confusing drivers behindyou.
Constant application of the brakeswhen going down a long hill buildsup heat and reduces their effective-ness. Use the engine to assist thebrakes by taking your foot off theaccelerator and downshifting to alower gear.
Braking System Design
Brake Wear Indicators
Braking System
146
CONTINUED
The anti-lock brake system (ABS)helps prevent the brakes fromlocking up, and helps you retainsteering control by pumping thebrakes rapidly, much faster than aperson can do it.
Let the ABS work for you by alwayskeeping firm, steady pressure on thebrake pedal. This is sometimesreferred to as ‘‘stomp and steer.’’
The ABS also balances the front-to-rear braking distribution accordingto vehicle loading.
You will feel a pulsation in the brakepedal when the ABS activates, andyou may hear some noise. This isnormal: it is the ABS rapidlypumping the brakes. On drypavement, you will need to press onthe brake pedal very hard before theABS activates. However, you may
feel the ABS activate immediately ifyou are trying to stop on snow or ice.
If the ABS indicator comes on, theanti-lock function of the brakingsystem has shut down. The brakesstill work like a conventional system,but without anti-lock. You shouldhave your dealer inspect your vehicleas soon as possible.
If the ABS indicator comes on whiledriving, test the brakes as shown onpage .
If the ABS indicator and the brakesystem indicator come on together,and the parking brake is fullyreleased, the front-to-rear brakingdistribution system may also be shutdown.
Test your brakes as instructed onpage . If the brakes feel normal,drive slowly and have your vehiclerepaired by your dealer as soon aspossible. Avoid sudden hard brakingwhich could cause the rear wheels tolock up and possibly lead to a loss ofcontrol.
202
202
If equipped
You should never pump the brake pedal.
Anti-lock Brakes (ABS)
ABS Indicator
Driving
147
ABS INDICATOR
It only helps with thesteering control during braking.
such as trying to take acorner too fast or making a suddenlane change. Always drive at a safespeed for the road and weatherconditions.
Always steer moderatelywhen you are braking hard. Severeor sharp steering wheel movementcan still cause your vehicle to veerinto oncoming traffic or off the road.
on loose oruneven surfaces, such as gravel orsnow, than a vehicle without anti-lock. Slow down and allow a greaterdistance between vehicles underthose conditions.
Your vehicle is not designed to tow atrailer, attempting to do so can voidyour warranties.
ABS does not reduce the time ordistance it takes to stop thevehicle.
ABS will not prevent a skid thatresults from changing directionabruptly,
ABS cannot prevent a loss ofstability.
A vehicle with ABS may require alonger distance to stop
Important Safety Reminders Towing a Trailer
Anti-Lock Brakes (ABS), Towing a Trailer
148
This section explains why it isimportant to keep your vehicle wellmaintained and how to follow basicmaintenance safety precautions.
......................Maintenance Safety . 150.................Maintenance Schedule . 151
....................Maintenance Record . 155..............................Fluid Locations . 158
........................Adding Engine Oil . 159.......Recommended Engine Oil . 159
..............................Synthetic Oil . 160................Engine Oil Additives . 160
.........Changing the Oil and Filter . 160..............................Engine Coolant . 162
....................Windshield Washers . 164....Automatic Transmission Fluid . 165
........Manual Transmission Fluid . 167................Brake and Clutch Fluid . 168
....................Power Steering Fluid . 169....................................Timing Belt . 169
.............................................Lights . 170................Cleaning the Seat Belts . 174
.....................................Floor Mats . 175..................Dust and Pollen Filter . 176
.................................Wiper Blades . 176...............................................Tires . 178
...................Checking the Battery . 184.............................Vehicle Storage . 185
This section also includesmaintenance schedules for normaldriving and severe driving conditions,a maintenance record, andinstructions for simple maintenancetasks you may want to take care ofyourself.
If you have the skills and tools toperform more complex maintenancetasks on your vehicle, you may wantto purchase the service manual. Seepage for information on how toobtain a copy, or see your dealer.
227
MaintenanceM
aintenance
149
To eliminate potential hazards, readthe instructions before you begin,and make sure you have the toolsand skills required.
Donot run the engine unlessinstructed to do so.
Some of the most important safetyprecautions are given here. However,we cannot warn you of everyconceivable hazard that can arise inperforming maintenance. Only youcan decide whether or not youshould perform a given task.
All service items not detailed in thissection should be performed by acertified technician or other qualifiedmechanic.
Make sure your vehicle is parkedon level ground, the parking brakeis set, and the engine is off.
To clean parts, use a commerciallyavailable degreaser or partscleaner, not gasoline.
To reduce the possibility of fire orexplosion, keep cigarettes, sparks,and flames away from the batteryand all fuel-related parts.
Wear eye protection andprotective clothing when workingwith the battery or compressed air.
Be sure there isadequate ventilation whenever youoperate the engine.
Let theengine and exhaust system coolbefore touching any parts.
Maintenance Safety
Important Safety Precautions
Injury from moving parts.
Potential Vehicle HazardsCarbon Monoxide poison fromengine exhaust.
Burns from hot parts.
150
Failure to properly followmaintenance instructions andprecautions can cause you tobe seriously hurt or killed.
Always follow the proceduresand precautions in this owner’smanual.
Improperly maintaining thisvehicle, or failing to correct aproblem before driving cancause a crash in which you canbe seriously hurt or killed.
Always follow the inspectionand maintenancerecommendations andschedules in this owner’smanual.
-
-
Avoid exceeding your vehicle’sload limit. This puts excess stresson the engine, brakes, and manyother vehicle parts. The load limitis shown on the tire informationlabel on the driver’s doorjamb.
Operate your vehicle onreasonable roads within the legalspeed limit.
Drive your vehicle regularly over adistance of several miles(kilometers).
Always use unleaded gasoline withthe proper octane rating (see page
).
Service your vehicle according to thetime and mileage periods on one ofthe Maintenance Schedules on thefollowing pages.
Follow theMaintenance Schedule for SevereConditions if you drive your vehicleMAINLY under one or more of thefollowing conditions.
Driving in extremely hot [over90°F (32°C)] conditions.
Driving less than 5 miles (8 km)per trip or, in freezingtemperatures, driving less than 10miles (16 km) per trip.
Driving on muddy, dusty, or de-iced roads.
Follow theMaintenance Schedule for SevereConditions.
The maintenance schedule assumesyou will use your vehicle as normaltransportation for passengers andtheir possessions. You should alsofollow these recommendations:
Extensive idling or long periods ofstop-and-go driving, such as a taxior a commercial delivery vehicle.
If you only OCCASIONALLYdrive under a ‘‘severe’’ condition, youshould follow the MaintenanceSchedule for Normal Conditions.
Driving with a loaded roof rack, ordriving in mountainous conditions.
122
CONTINUED
Maintenance Schedule
Which Schedule to Follow
U.S. Owners
Canadian Owners
Maintenance
151
NOTE:
-
-
-
-
-
-
#
Engine oil level Check everytime you fill the fuel tank. Seepage .
Engine coolant level Check theradiator reserve tank every timeyou fill the fuel tank. See page .
Automatic transmission Checkthe fluid level monthly. See page
.
Brakes Check the fluid levelmonthly. See page .
Tires Check the tire pressuremonthly. Examine the tread forwear and foreign objects. See page
.
Lights Check the operation ofthe headlights, parking lights,taillights, high-mount brake light,and license plate lights monthly.See page .
We recommend the use of Hondaparts and fluids whenever you havemaintenance done.
U.S. Vehicles:
According to state and federalregulations, failure to performmaintenance on the items markedwith will not void your emissionswarranties. However, allmaintenance services should beperformed at the recommended timeor mileage period to ensure long-term reliability.
You should check the followingitems at the specified intervals. Ifyou are unsure of how to performany check, turn to the appropriatepage listed.
Your authorized dealer knows yourvehicle best and can providecompetent, efficient service.However, service at a dealer is notmandatory to keep your warrantiesin effect. Maintenance may be doneby any qualified service facility orskilled person to keep yourwarranties in effect. Keep all thereceipts as proof of completion, andhave the person who does the workfill out the maintenance record.Check your warranty booklet formore information.
165
126
168
178
170
125
Maintenance Schedule
Maintenance,replacement, or repair ofemissions control devices andsystems may be done by anyautomotive repair establishmentor individual using parts that are‘‘certif ied’’ to EPA standards.
Owner’s Maintenance Checks
Servicing Your Vehicle
152
-
#**
#
#
*
*
153
Canadian Owners
Service the items listed at the indicated distance (or time, if given).miles x 1,000km x 1,000
1016
2032
3048
4064
5080
70112
80128
90144
120192
130208
150240
Check oil and coolant at each fuel stopCheck inflation and condition once a month
Every 10,000 miles (16,000 km) or every 1 year, whichever comes firstEvery 10,000 miles (16,000 km)
Every 20,000 miles (32,000 km) or every 1 year, whichever comes first
Every 30,000 miles (48,000 km) or every 2 years, whichever comes first
Inspect every 110,000 miles (176,000 km), otherwise adjust only if noisy
Every 120,000 miles (192,000 km) or every 6 years, whichever comes first
Every 110,000 miles (176,000 km) or every 7 years, whichever comes firstAt 120,000 miles (192,000 km) or 10 years, then every 60,000 miles (96,000 km) or 5 years
Every 3 years (independent of mileage)
See information on maintenance and emissions warranty, middle column, page .Replace at 120,000 miles (192,000 km) or 6 years, then every 90,000 miles (144,000 km) or 5 years.Replace at 60,000 miles (96,000 km) or 3 years, then every 40,000 miles (64,000 km) or 2 years.
Check engine oil and coolantCheck tiresReplace engine oilRotate tires (follow pattern on page 181 )Replace engine oil filterCheck front and rear brakesCheck parking brake adjustmentInspect the following items:
Tie-rod ends, steering gearbox, and bootsSuspension componentsDriveshaft bootsBrake hoses and lines (including ABS)All fluid levels and condition of fluidsExhaust systemFuel lines and connections
Inspect and adjust drive beltsReplace dust and pollen filterReplace air cleaner elementReplace spark plugsInspect valve clearanceReplace automatic transmission fluidReplace manual transmission fluidReplace CVT fluidInspect idle speedReplace timing belt, inspect auto-tensioner and water pumpReplace engine coolantReplace brake fluid
6096
100160
110176
140224
Follow the maintenance schedule for severe conditions.
152:1:2:
1
2
Main
tenance
Sch
edule
for
Norm
alC
onditio
ns
#****
# #
*
*
*
#*
154
Service the items listed at the indicated distance (or time, if given).miles x 1,000km x 1,000
1016
2032
3048
4064
5080
70112
80128
130208
Check oil and coolant at each fuel stopCheck inflation and condition once a month
Every 5,000 miles (8,000 km) or every 6 months, whichever comes firstEvery 10,000 miles (16,000 km)
Every 10,000 miles (16,000 km) or every 1 year, whichever comes first
Every 20,000 miles (32,000 km) or every 1 year, whichever comes first
Every 30,000 miles (48,000 km) or every 2 years, whichever comes first
Every 15,000 miles (24,000 km) (Use normal schedule except in dusty conditions)
Inspect every 110,000 miles (176,000 km), otherwise adjust only if noisy
Every 3 years (independent of mileage)At 120,000 miles (192,000 km) or 10 years, then every 60,000 miles (96,000 km) or 5 years
Every 110,000 miles (176,000 km) or every 7 years, whichever comes first
See information on maintenance and emissions warranty, middle column, page .See dust and pollen filter on page for replacement information under special driving conditions.Replace at 60,000 miles (96,000 km) or 3 years, then every 30,000 miles (48,000 km) or 2 years.Replace at 60,000 miles (96,000 km) or 3 years, then every 40,000 miles (64,000 km) or 2 years.See timing belt on page for replacement information under special driving conditions.
Every 60,000 miles (96,000 km) or every 3 years, whichever comes first
90144
120192
150240
110176
140224
100160
6096
Check engine oil and coolantCheck tiresReplace engine oilRotate tires (follow pattern on page 181 )Replace engine oil filterCheck front and rear brakesLubricate all hinges, locks and latchesInspect the following items:
Tie-rod ends, steering gearbox, and bootsSuspension components, Driveshaft boots
Check parking brake adjustmentInspect the following items:
Brake hoses and lines (including ABS)All fluid levels and condition of fluidsExhaust system , Fuel lines and connectionsLights and controls/vehicle underbody
Inspect and adjust drive beltsReplace dust and pollen filterReplace air cleaner elementReplace spark plugsInspect valve clearanceReplace automatic transmission fluidReplace manual transmission fluidReplace CVT fluidInspect idle speedReplace timing belt , inspect auto-tensioner and water pumpReplace engine coolantReplace brake fluid
:1:2:3:4:
152176
169
1
2
3
, 4
Main
tenance
Sch
edule
for
Seve
reC
onditi
ons
CONTINUED
(for Normal and Severe Schedules)Maintenance RecordM
aintenance
155
5,000 mi
10,000 mi
15,000 mi
20,000 mi
25,000 mi
30,000 mi
35,000 mi
40,000 mi
45,000 mi
50,000 mi
You or the servicing dealer can record all completed maintenance here, whether you follow the schedule for normal conditions (page ) or severeconditions (page ). Keep the receipts for all work done on your vehicle.
8,000 km
16,000 km
24,000 km
32,000 km
40,000 km
48,000 km
56,000 km
64,000 km
72,000 km
80,000 km
Signature or dealer stamp Signature or dealer stampmi/km
Date
mi/km
mi/km
mi/km
mi/km
Date
Date
Date
Date
Date
Date
Date
Date
Date
mi/km
mi/km
mi/km
mi/km
mi/km
153154
(for Normal and Severe Schedules)Maintenance Record
156
55,000 mi
60,000 mi
65,000 mi
70,000 mi
75,000 mi
80,000 mi
85,000 mi
90,000 mi
95,000 mi
100,000 mi
88,000 km
96,000 km
104,000 km
112,000 km
120,000 km
Signature or dealer stamp128,000 km
136,000 km
144,000 km
152,000 km
160,000 km
Signature or dealer stampmi/km
mi/km
mi/km
mi/km
mi/km
Date
Date
Date
Date
Date
Date
Date
Date
Date
Date
mi/km
mi/km
mi/km
mi/km
mi/km
(for Normal and Severe Schedules)Maintenance RecordM
aintenance
157
105,000 mi
110,000 mi
115,000 mi
120,000 mi
125,000 mi
130,000 mi
135,000 mi
140,000 mi
145,000 mi
150,000 mi
168,000 km
176,000 km
184,000 km
192,000 km
200,000 km
Signature or dealer stamp208,000 km
216,000 km
224,000 km
232,000 km
240,000 km
Signature or dealer stampmi/km
mi/km
mi/km
mi/km
mi/km
mi/km
mi/km
mi/km
mi/km
mi/km
Date
Date
Date
Date
Date
Date
Date
Date
Date
Date
Fluid Locations
158
BRAKE FLUID(Gray cap)
WASHER FLUID(Blue cap)
POWER STEERINGFLUID (Red cap)
AUTOMATICTRANSMISSION FLUIDDIPSTICK (CVT)(Yellow loop)RADIATOR CAP
ENGINECOOLANTRESERVOIR
ENGINE OIL DIPSTICK(Orange loop)
AUTOMATICTRANSMISSIONFLUID DIPSTICK(except CVT)(Yellow loop)
CLUTCH FLUID(Manualtransmission only)(Gray cap)
ENGINE OILFILL CAP
Oil is a major contributor to yourengine’s performance and longevity.Always use a premium-grade 5W-20detergent oil displaying the APICertification Seal. This seal indicatesthe oil is energy conserving, and thatit meets the American PetroleumInstitute’s latest requirements.
Honda Motor Oil is the preferred5W-20 lubricant for your vehicle. It ishighly recommended that you useHonda Motor Oil in your vehicle foroptimum engine protection. Makesure the API Certification Seal says‘‘For Gasoline Engines.’’
Unscrew and remove the engine oilfill cap on top of the valve cover.Pour in the oil slowly and carefully soyou do not spill. Clean up any spillsimmediately. Spilled oil coulddamage components in the enginecompartment.
Install the engine oil fill cap, andtighten it securely. Wait a fewminutes, and recheck the oil level.Do not fill above the upper mark; youcould damage the engine.
The oil’s viscosity or weight isprovided on the container’s label.5W-20 oil is formulated for year-round protection of your vehicle, toimprove cold weather starting andfuel economy.
Recommended Engine Oil
Adding Engine OilM
aintenance
159
ENGINE OILFILL CAP
API CERTIFICATION SEAL
Ambient Temperature
Always change the oil and filteraccording to the recommendations inthe maintenance schedule. The oiland filter collect contaminants thatcan damage your engine if they arenot removed regularly.
Changing the oil and filter requiresspecial tools and access fromunderneath the vehicle. The vehicleshould be raised on a service station-type hydraulic lift for this service.Unless you have the knowledge andproper equipment, you should havethis maintenance done by a skilledmechanic.
Run the engine until it reachesnormal operating temperature,then shut it off.
Open the hood, and remove theengine oil fill cap. Remove the oildrain bolt and washer from thebottom of the engine. Drain the oilinto an appropriate container.
You may use a synthetic motor oil ifit meets the same requirementsgiven for a conventional motor oil: itdisplays the API Certification Seal,and it is the proper weight. You mustfollow the oil and filter changeintervals given on the maintenanceschedule.
Your vehicle does not require any oiladditives. Additives may adverselyaffect your engine’s or transmission’sperformance and durability.
1.
2.
Changing the Oil and FilterSynthetic Oil
Engine Oil Additives
Adding Engine Oil, Changing the Oil and Filter
160
DRAIN BOLT WASHER
Replace the engine oil fill cap.Start the engine. The oil pressureindicator should go out within 5seconds. If it does not, turn off theengine, and check your work.
Turn off the engine, let it sit forseveral minutes, then check the oillevel on the dipstick. If necessary,add more oil.
Put a new washer on the drain bolt,then reinstall the drain bolt.Tighten the drain bolt to :
Let the engine run for severalminutes, then check the drain boltand oil filter for leaks.
Install a new oil filter according tothe instructions that come with it.
Remove the oil filter, and let theremaining oil drain. A specialwrench (available from yourdealer) is required.
Make sure to clean off any dirtand dust on the connectingsurface of a new oil filter.
Refill the engine with therecommended oil.Engine oil change capacity(including filter):
5.
6.
7.
8.
9.
(U.S.: EX, EX Special Edition, HX,Canada: Si)
3.
4.
(U.S.: DX, Value Package, LX, LXSpecial Edition, Canada: DX,REVERB, LX)
(U.S.: EX, EX Special Edition, HX,Canada: Si)
(U.S.: DX, Value Package, LX, LXSpecial Edition, Canada: DX,REVERB, LX)
Changing the Oil and FilterM
aintenance
161
OIL FILTER
33 lbf·ft (44 N·m , 4.5 kgf·m)
29 lbf·ft (39 N·m , 4.0 kgf·m)
3.7 US qt (3.5 )
3.4 US qt (3.2 )
Improper disposal of engine oil can beharmf ul to the environment. If youchange your own oil, please dispose ofthe used oil properly. Put it in a sealedcontainer and take it to a recyclingcenter. Do not discard it in a trash binor dump it on the ground.
If the coolant level in the reservetank is at or below the MIN line, addcoolant to bring it up to the MAX line.Inspect the cooling system for leaks.
Always use Honda All SeasonAntifreeze/Coolant Type 2. Thiscoolant is pre-mixed with 50 percentantifreeze and 50 percent water.Never add straight antifreeze orplain water.
If Honda antifreeze/coolant is notavailable, you may use anothermajor-brand non-silicate coolant as atemporary replacement. Make sure itis a high-quality coolantrecommended for aluminum engines.Continued use of any non-Hondacoolant can result in corrosion,causing the cooling system tomalfunction or fail. Have the coolingsystem flushed and refilled withHonda antifreeze/coolant as soon aspossible.
If the reserve tank is completelyempty, you should also check thecoolant level in the radiator.
Adding Engine Coolant
Engine Coolant
162
RESERVE TANK Removing the radiator capwhile the engine is hot cancause the coolant to spray out,seriously scalding you.
Always let the engine andradiator cool down beforeremoving the radiator cap.
When the radiator and engine arecool, relieve any pressure in thecooling system by turning theradiator cap counterclockwise,without pressing down.
The coolant level should be up tothe base of the filler neck. Addcoolant if it is low.
Pour the coolant slowly andcarefully so you do not spill. Cleanup any spill immediately; it coulddamage components in the enginecompartment.
Put the radiator cap back on andtighten it.
Remove the radiator cap bypushing down and turningcounterclockwise.
Pour coolant into the reserve tank.Fill it to halfway between the MAXand MIN marks. Put the cap backon the reserve tank.
Do not add any rust inhibitors orother additives to your vehicle’scooling system. They may not becompatible with the coolant orengine components.
1.
2.
3.
4.
5.
Engine CoolantM
aintenance
163
RADIATOR CAP RESERVE TANK
Check the fluid level in thewindshield washer reservoir at leastmonthly during normal use.
When you refill the reservoir, cleanthe edges of the windshield wiperblades with windshield washer fluidon a clean cloth. This will help tocondition the blade edges.
Fill the reservoir with a good-qualitywindshield washer fluid. Thisincreases the cleaning capability andprevents freezing in cold weather.
The low washerlevel indicator comes on when thelevel is low (see page ).
Check the fluid level by removingthe cap and looking at the levelgauge.
56
On Canadian models:
Windshield Washers
164
LEVEL GAUGE
Do not use engine antif reeze or avinegar/water solution in thewindshield washer reservoir. Antif reezecan damage your vehicle’s paint, whilea vinegar/water solution can damagethe windshield washer pump. Use onlycommercially-available windshieldwasher f luid.
Check the fluid level with the engineat normal operating temperature.
Park the vehicle on level ground.Shut off the engine.
Remove the dipstick (yellow loop)from the transmission, and wipe itwith a clean cloth.
Remove the dipstick and checkthe fluid level. It should bebetween the upper and lowermarks.
Insert the dipstick all the way intothe transmission securely asshown in the illustration.NOTE: For accurate results, wait at
least 60 seconds, and no more than90 seconds, after turning off theengine to check the fluid level.
3.
4.
1.
2.
CONTINUED
Automatic Transmission FluidM
aintenance
165
DIPSTICK (A/T)
LOWER MARKUPPER MARK
DIPSTICK (CVT)
DIPSTICK (A/T)
If the level is below the lowermark, add fluid into the filler holeto bring it to the upper mark (OnCVT model, the HOT side’s uppermark).
Remove the dipstick and check thefluid level. There is a HOT side and aCOLD side on the dipstick. It shouldbe between the upper and lowermarks on the HOT side.
To thoroughly flush the transmission,the technician should drain and refillit with Honda ATF-Z1, then drive thevehicle for a short distance. Do thisthree times. Then drain and refill thetransmission a final time.
Insert the dipstick all the way backinto the transmission securely asshown in the illustration.
If you are not sure how to add fluid,contact your dealer.
The transmission should be drainedand refilled with new fluid accordingto the time and distance recommen-dations in the maintenance schedule.
Pour the fluid slowly and carefullyso you do not spill any. Clean upany spills immediately; it coulddamage components in the enginecompartment.
Always use Honda ATF-Z1(Automatic Transmission Fluid). Ifit’s not available, you may use aDEXRON III automatictransmission fluid as a temporaryreplacement. However, continueduse can affect the shift quality.Have the transmission flushed andrefilled with Honda ATF-Z1 assoon as it is convenient.
5.
6.
On CVT model
Automatic Transmission Fluid
166
UPPER MARK
DIPSTICK (CVT)
LOWER MARK
If Honda MTF is not available, youmay use an SAE 10W-30 or 10W-40viscosity motor oil with the APICertification seal that says ‘‘FORGASOLINE ENGINES’’ as atemporary replacement. However,motor oil does not contain the properadditives, and continued use cancause stiffer shifting. Replace assoon as it is convenient.
The transmission should be drainedand refilled with new fluid accordingto the time and distance recommen-dations in the maintenance schedule.
Check the fluid level with thetransmission at normal operatingtemperature and the vehicle sittingon level ground. Remove thetransmission filler bolt, and carefullyfeel inside the bolt hole with yourfinger. The fluid level should be upto the edge of the bolt hole. If it isnot, add Honda ManualTransmission Fluid (MTF) until itstarts to run out of the hole. Reinstallthe filler bolt, and tighten it securely.
If you are not sure how to check andadd fluid, contact your dealer.
Manual Transmission FluidM
aintenance
167
FILLER BOLT
Correct Level
The fluid level should be betweenthe MIN and MAX marks on the sideof the reservoir. If the level is at orbelow the MIN mark, your brakesystem needs attention. Have thebrake system inspected for leaks orworn brake pads.
The fluid level should be betweenthe MIN and MAX marks on the sideof the reservoir. If it is not, addbrake fluid to bring it up to that level.Use the same fluid specified for thebrake system.
Check the fluid level in the brakefluid reservoir monthly.
Replace the brake fluid according tothe time recommendation in themaintenance schedule.
Brake fluid marked DOT 5 is notcompatible with your vehicle’sbraking system and can causeextensive damage.
Using any non-Honda brake fluid cancause corrosion and decrease the lifeof the system. Have the brakesystem flushed and refilled withHonda Heavy Duty Brake FluidDOT 3 as soon as possible.
Always use Honda Heavy DutyBrake Fluid DOT 3. If it is notavailable, you should use only DOT 3or DOT 4 fluid, from a sealedcontainer, as a temporaryreplacement.
A low fluid level can indicate a leakin the clutch system. Have thissystem inspected as soon as possible.
Manual Transmission onlyClutch FluidBrake System
Brake and Clutch Fluid
168
MAX
MIN
MAX
MIN
- -
Check the level on the side of thereservoir when the engine is cold.The fluid should be between theUPPER LEVEL and LOWER LEVEL.If not add power steering fluid to theUPPER LEVEL mark.
Always use Honda Power SteeringFluid. You may use another powersteering fluid as an emergencyreplacement, but have the powersteering system flushed and refilledwith Honda PSF as soon as possible.
A low power steering fluid level canindicate a leak in the system. Checkthe fluid level frequently, and havethe system inspected as soon aspossible.
The timing belt should be replacedat the intervals shown in themaintenance schedule. Replace thebelt at 60,000 miles (100,000 km) ifyou regularly drive your vehicle inone or more of these conditions:
In very high temperatures(over 110°F, 43°C).
In very low temperatures(under 20°F, 29°C).
Pour the fluid slowly and carefully soyou do not spill. Clean up any spillsimmediately; it could damagecomponents in the enginecompartment.
Power Steering Fluid Timing Belt
Power Steering Fluid, Timing BeltM
aintenance
169
UPPER LEVEL
LOWER LEVEL
Turning the steering wheel to f ull lef tor right lock and holding it there candamage the power steering pump.
If you need to change theheadlight bulb on the driver’s side,remove the power steeringreservoir tank by pulling it out ofits holder.
The headlights were properly aimedwhen your vehicle was new. If youregularly carry heavy items in thetrunk, readjustment may be required.Adjustment should be done by yourdealer or other qualified mechanic.
Your vehicle has halogen headlightbulbs. When replacing a bulb, handleit by its base, and protect the glassfrom contact with your skin or hardobjects. If you touch the glass, cleanit with denatured alcohol and a cleancloth.
1.
Lights
Headlight Aiming Replacing a Headlight Bulb
170
HOLDERHalogen headlight bulbs get very hotwhen lit. Oil, perspiration, or a scratchon the glass can cause the bulb tooverheat and shatter.
If you need to change a headlightbulb on the passenger’s side, removethe bolt from the stay and push thebattery toward windshield to obtainenough working space.
Remove the electrical connectorfrom the bulb by pushing on thetab and pulling the connectordown.
Remove the bulb by turning it one-quarter turn counterclockwise.
Push the electrical connector backonto the bulb. Make sure it is onall the way.
Turn on the headlights to test thenew bulb.
Put the battery back to its originalposition, reinstall the bolt in thestay and tighten it securely.
Reinstall the power steeringreservoir.
(Passenger’s side)
(Driver’s side)
Insert the new bulb into the holeand turn it one-quarter turn clock-wise to lock it in place.
2.
3.
4.
5.
6.
7.
LightsM
aintenance
171
STAY TAB
BULB
CONNECTOR
If you are changing the bulb onthe driver’s side, start the engine,turn the steering wheel all the wayto the right, and turn off theengine. If you are changing thebulb on the passenger’s side, turnthe steering wheel to the left.
Use a flat-tipped screwdriver toremove the holding clip from theinner fender, and pull the innerfender cover back.
Remove the socket from theheadlight assembly by turning itone-quarter turn counterclockwise.
Remove the bulb from the socketby pushing it in and turning thebulb counterclockwise until itunlocks.
Install the new bulb in the socket.Turn it clockwise to lock it in place.
Insert the socket back into theheadlight assembly. Turn itclockwise to lock it in place.
Put the inner fender cover in place.Install the holding clip. Lock it inplace by pushing on the center.
2.1.
3.
4.
5.
6.
7.
Lights
Replacing the Front Side Marker/Turn Signal and Parking LightBulb
172
BULB
SOCKET
Open the trunk. Determine which of the threebulbs is burned out: stop/taillight,back-up light or turn signal light.
Remove the socket by turning itone-quarter turn counterclockwise.
Pull the bulb straight out of itssocket. Push the new bulb straightinto the socket until it bottoms.
Remove the screw in the center ofthe fastener on the side of thetrunk lining. Pull the lining back.
Reinstall the socket into the lightassembly by turning it clockwiseuntil it locks.
Turn on the lights to make surethe new bulb is working.
Reinstall the trunk lining. Makesure it is installed under the edgeof the trunk seal.
Put the fastener into the hole onthe side of the trunk lining.Reinstall the screw.
1. 2.
3.
4.
5.
6.
7.
8.
Lights
Replacing Rear Bulbs
Maintenance
173
FASTENER
BULBS
BULB
SOCKET
SOCKETS
Reinstall the socket. Turn itclockwise until it locks. Make surethe new bulb is working.
Pull the bulb straight out of itssocket. Push the new bulb straightinto the socket until it bottoms.
Open the trunk and remove thesocket from the light assembly byturning it one-quarter turn counter-clockwise.
If your seat belts get dirty, use a softbrush with a mixture of mild soapand warm water to clean them. Donot use bleach, dye, or cleaningsolvents. Let the belts air-dry beforeyou use the vehicle.
3.
2.
1.
EXcept U.S. Special Edition models andCanadian REVERB and Si models
Lights, Cleaning the Seat Belts
Replacing a High-mount BrakeLight Bulb
Cleaning the Seat Belts
174
SOCKET
BULB
LOOP
If equipped
If you remove the driver’s floor mat,make sure to re-anchor it when youput it back in your vehicle.
Dirt build-up in the loops of the seatbelt anchors can cause the belts toretract slowly. Wipe the insides ofthe loops with a clean clothdampened in mild soap and warmwater or isopropyl alcohol.
The driver’s floor mat that camewith your vehicle hooks over thefloor mat anchors. This keeps thefloor mat from sliding forward andpossibly interfering with the pedals.
If you use a non-Honda floor mat,make sure it fits properly and that itcan be used with the floor matanchor. Do not put additional floormats on top of the anchored mat.
Floor Mats
Cleaning the Seat Belts, Floor MatsM
aintenance
175
Disconnect the blade assemblyfrom the wiper arm by pushing inthe lock tab. Hold the lock tab inwhile you push the blade assemblytoward the base of the arm.
Check the condition of the wiperblades at least every six months.Replace them if you find signs ofcracking in the rubber, areas that aregetting hard, or if they leave streaksand unwiped areas when used.
Raise the wiper arm off thewindshield.
This filter removes the dust andpollen that is brought in from theoutside through the heating andcooling system.
Have your dealer replace this filterevery 30,000 miles (48,000 km)under normal conditions. It shouldbe replaced every 15,000 miles(24,000 km) if you drive primarily inurban areas that have highconcentrations of soot in the air, or ifthe flow from the heating andcooling system becomes less thanusual.
2.
1.
If equipped with A/CWiper BladesDust and Pollen Filter
Dust and Pollen Filter, Wiper Blades
176
LOCK TAB
Do not open the hood when the wiperarms are raised, or you will damage thehood and wiper arms.
Slide the new wiper blade into theholder until the tabs lock.
Slide the wiper blade assemblyonto the wiper arm. Make sure itlocks in place.
Lower the wiper arm down againstthe windshield.
Examine the new wiper blades. Ifthey have no plastic or metalreinforcement along the backedge, remove the metalreinforcement strips from the oldwiper blade, and install them inthe slots along the edge of the newblade.
Remove the blade from its holderby grasping the tabbed end of theblade. Pull firmly until the tabscome out of the holder.
4.
5.
6.
7.
3.
Wiper BladesM
aintenance
177
REINFORCEMENT
BLADE
BLADE
Keeping the tires properly inflatedprovides the best combination ofhandling, tread life, and ridingcomfort.
Underinflated tires wear unevenly,adversely affect handling and fueleconomy, and are more likely tofail from being overheated.
Overinflated tires can make yourvehicle ride more harshly, aremore prone to damage from roadhazards, and wear unevenly.
We recommend that you visuallycheck your tires every day. If youthink a tire might be low, check itimmediately with a tire gauge.
The following pages give moredetailed information on how to takecare of your tires and what to dowhen they need to be replaced.
To safely operate your vehicle, yourtires must be the proper type andsize, in good condition with adequatetread, and correctly inflated.
Use a gauge to measure the airpressure in each tire at least once amonth. Even tires that are in goodcondition may lose one to two psi (10to 20 kPa, 0.1 to 0.2 kgf/cm ) permonth. Remember to check thespare tire at the same time.
Check the air pressures when thetires are cold. This means thevehicle has been parked for at leastthree hours, or driven less than 1mile (1.6 km). Add or release air, ifneeded, to match the recommendedcold tire pressures on page .179
Tires
Inflation Guidelines
178
Using tires that are excessivelyworn or improperly inflated cancause a crash in which you canbe seriously hurt or killed.
Follow all instructions in thisowner’s manual regarding tireinflation and maintenance.
While tubeless tires have someability to self-seal if they arepunctured, you should look closelyfor punctures if a tire starts losingpressure.
You should use your own tirepressure gauge whenever you checkyour tire pressures. This will make iteasier for you to tell if a pressureloss is due to a tire problem and notdue to a variation between gauges.
If you check air pressures when thetires are hot [driven for several miles(kilometers)], you will see readings 4to 6 psi (30 to 40 kPa, 0.3 to 0.4kgf/cm ) higher than the coldreadings. This is normal. Do not letair out to match the recommendedcold air pressure. The tire will beunderinflated.
The following charts show therecommended cold tire pressures formost normal driving conditions andspeeds.
Honda strongly recommends thatyou not drive faster than postedspeed limits and conditions allow. Ifyou decide it is safe to drive at highspeeds (over 100 mph or 160 km/h),be sure to adjust the cold tirepressures as shown below. If you donot, excessive heat can build up andcause sudden tire failure.
The compact spare tire pressure is:
Tire Size
Cold Tire Pressurefor High-SpeedDriving
Tire Size Cold Tire Pressurefor Normal Driving
Tire Size Cold Tire Pressurefor Normal Driving
Tire Size Cold Tire Pressurefor Normal Driving
CONTINUED
U.S.: DX, Value Package, HX, Canada: DX
Canada: LX
U.S.: DX, Value Package, HX, Canada: DX
U.S. DX, Value Package, HX andCanadian DX models only
U.S.: LX, EX, Special Edition, Canada: Si, REVERB
Tires
Recommended Tire PressuresNormal Driving
High-Speed Driving
Maintenance
179
60 psi (420 kPa , 4.2 kgf/cm )
P185/70R14 87S 35 psi (240 kPa , 2.4kgf/cm )
P195/60R15 87H 30 psi (210 kPa , 2.1kgf/cm )
P185/65R15 86H 30 psi (210 kPa , 2.1kgf/cm )
P185/70R14 87S 30 psi (210 kPa , 2.1kgf/cm )
Every time you check inflation, youshould also examine the tires fordamage, foreign objects, and wear.
You should look for:Bumps or bulges in the tread orside of the tire. Replace the tire ifyou find either of these conditions.
Cuts, splits, or cracks in the sideof the tire. Replace the tire if youcan see fabric or cord.
Excessive tread wear.
Tire pressure for high-speed drivingis the same as for normal driving.
When you return to normal speeddriving, be sure to readjust the tirepressure for normal driving. Youshould wait until the tires are coldbefore adjusting the tire pressure.
For convenience, the recommendedtire sizes and cold air pressures areon a label on the driver’s doorjamb.
For additional information aboutyour tires, see page .
Your tires have wear indicatorsmolded into the tread. When thetread wears down, you will see aband 1/2 inch (12.7 mm) wide acrossthe tread. This shows there is lessthan 1/16 inch (1.6 mm) of tread lefton the tire.
A tire this worn gives very littletraction on wet roads. You shouldreplace the tire if you can see threeor more tread wear indicators.
216
U.S. LX, EX, Special Edition andCanadian REVERB, LX, Si models
Tire Inspection
Tires
180
INDICATOR LOCATION MARKS
TREAD WEAR INDICATOR
In addition to proper inflation,correct wheel alignment helps todecrease tire wear. If you find a tireis worn unevenly, have your dealercheck the wheel alignment.
Have your dealer check the tires ifyou feel a consistent vibration whiledriving. A tire should always berebalanced if it is removed from thewheel. When you have new tiresinstalled, make sure they arebalanced. This increases ridingcomfort and tire life. For best results,have the installer perform a dynamicbalance.
To help increase tire life anddistribute wear more evenly, rotatethe tires every 10,000 miles (16,000km). Move the tires to the positionsshown in the chart each time theyare rotated. If you purchasedirectional tires, rotate only front-to-back.
Replace your tires with radial tires ofthe same size, load range, speedrating, and maximum cold tirepressure rating (as shown on thetire’s sidewall).
Mixing radial and bias-ply tires onyour vehicle can reduce brakingability, traction, and steeringaccuracy. Using tires of a differentsize or construction can cause theABS to work inconsistently.
It is best to replace all four tires atthe same time. If that is not possibleor necessary, replace the two fronttires or two rear tires as a pair.Replacing just one tire can seriouslyaffect your vehicle’s handling.
For vehicles equipped with aluminumwheels:
CONTINUED
Tire Maintenance Tire Rotation Replacing Tires and Wheels
TiresM
aintenance
181
Front Front
(Front Non-directionalTires and Wheels)
(Front DirectionalTires and Wheels)
Improper wheel weights can damageyour vehicle’s aluminum wheels. Useonly Honda wheel weights f orbalancing.
+The ABS works by comparing thespeed of the wheels. When replacingtires, use the same size originallysupplied with the vehicle. Tire sizeand construction can affect wheelspeed and may cause the system towork.
If you ever replace a wheel, makesure the new one matches thespecifications of the original.Replacement wheels are available atyour dealer.
Wheels: Tires marked ‘‘M S’’ or ‘‘AllSeason’’ on the sidewall have an all-weather tread design suitable formost winter driving conditions.
For the best performance in snowyor icy conditions, you should installsnow tires or tire chains. They maybe required by local laws undercertain conditions.
If you mount snow tires on yourvehicle, make sure they are radialtires of the same size and load rangeas original tires. Mount snow tires onall four wheels. The tractionprovided by snow tires on dry roadsmay be lower than your original tires.Check with the tire dealer formaximum speed recommendations.
See page for information aboutDOT Tire Quality Grading, and page
for tire size and labelinginformation.
Tires:
Canada: LX
U.S.: DX, Value Package, HXCanada: DX
U.S.: LX, EX, Special EditionCanada: LX, REVERB, Si
U.S.: DX,Value Package, HXCanada: DX
U.S.: LX, EX, Special EditionCanada: Si, REVERB
216
218
Tires
Wheel and Tire Specifications Winter Driving
Snow Tires
182
14 x 5 1/2 JJ
P195/60R15 87H
P185/65R15 86H
P185/70R14 87S
15 x 6 JJ
Installing improper tires on yourvehicle can affect handling andstability. This can cause a crashin which you can be seriouslyhurt or killed.
Always use the size and type oftires recommended in thisowner’s manual.
When installing cables, follow themanufacturer’s instructions, andmount them as tight as you can.Make sure they are not contactingthe brake lines or suspension. Driveslowly with them installed. If youhear them coming into contact withthe body or chassis, stop andinvestigate. Remove them as soon asyou begin driving on cleared roads.
Because your vehicle has limited tireclearance, mount only SAE Class ‘‘S’’cable-type traction devices, withrubber chain tensioners, on the fronttires. Use traction devices only whenrequired by driving conditions orlocal laws. Make sure they are thecorrect size for your tires. Metal link-type ‘‘chains’’ should not be used.
Tires
Tire Chains
Maintenance
183
Traction devices that are the wrongsize or improperly installed candamage your vehicle’s brake lines,suspension, body, and wheels. Stopdriving if they are hitting any part ofthe vehicle.
-
Check the condition of the batterymonthly by looking at the testindicator window. The label on thebattery explains the test indicator’scolors.
If additional battery maintenance isneeded, see your dealer or aqualified technician.
Battery posts,terminals, and related accessoriescontain lead and lead compounds.
If you need to connect the battery toa charger, disconnect both cables toprevent damaging your vehicle’selectrical system. Always disconnectthe negative ( ) cable first, andreconnect it last.
Check the terminals for corrosion (awhite or yellowish powder). Toremove it, cover the terminals with asolution of baking soda and water. Itwill bubble up and turn brown. Whenthis stops, wash it off with plainwater. Dry off the battery with acloth or paper towel. Coat theterminals with grease to help preventfurther corrosion.
WARNING:
Wash your hands after handling.
Checking the Battery
184
TEST INDICATOR WINDOW
The battery gives off explosivehydrogen gas during normaloperation.
A spark or flame can cause thebattery to explode with enoughforce to kill or seriously hurt you.
Wear protective clothing and aface shield, or have a skilledmechanic do the batterymaintenance.
If you need to park your vehicle foran extended period (more than onemonth), there are several things youshould do to prepare it for storage.Proper preparation helps preventdeterioration and makes it easier toget your vehicle back on the road. Ifpossible, store your vehicle indoors.
Fill the fuel tank.
Change the engine oil and filter.
Block the rear wheels.
If the vehicle is to be stored for alonger period, it should besupported on jackstands so thetires are off the ground.
Wash and dry the exteriorcompletely.
Clean the interior. Make sure thecarpeting, floor mats, etc., arecompletely dry.
Cover the vehicle with a‘‘breathable’’ cover, one madefrom a porous material such ascotton. Non-porous materials, suchas plastic sheeting, trap moisture,which can damage the paint.
Leave the parking brake off. Putthe transmission in Reverse(manual) or Park (automatic).
Leave one window open slightly (ifthe vehicle is being storedindoors).
If possible, periodically run theengine until it reaches fulloperating temperature (thecooling fans cycle on and offtwice). Preferably, do this once amonth.
If you store your vehicle for 1 year orlonger, have your dealer perform theinspections called for in the 2 years/30,000 miles (48,000 km)maintenance schedule (NormalConditions) as soon as you take itout of storage (see page ). Thereplacements called for in themaintenance schedule are notneeded unless the vehicle hasactually reached that time or mileage.
To minimize sticking, apply asilicone spray lubricant to all doorand trunk seals. Also, apply avehicle body wax to the paintedsurfaces that mate with the doorand trunk seals.
Support the front wiper bladearms with a folded towel or rag sothey do not touch the windshield.
Disconnect the battery.
153
Vehicle StorageM
aintenance
185
186
This section covers the morecommon problems that motoristsexperience with their vehicles. Itgives you information about how tosafely evaluate the problem and whatto do to correct it. If the problem hasstranded you on the side of the road,you may be able to get going again.If not, you will also find instructionson getting your vehicle towed.
......................Compact Spare Tire . 188....................Changing a Flat Tire . 189
.............If the Engine Won’t Start . 194................................Jump Starting . 196
..............If the Engine Overheats . 197.........Low Oil Pressure Indicator . 200..........Charging System Indicator . 200
.......Malfunction Indicator Lamp . 201...............Brake System Indicator . 202
..................Closing the Moonroof . 203..............................................Fuses . 204
..............................Fuse Locations . 207......................Emergency Towing . 209
Taking Care of the UnexpectedTaking
Care
ofthe
Unexpected
187
Use the compact spare tire as atemporary replacement only. Getyour regular tire repaired or replaced,and put it back on your vehicle assoon as you can.
Check the inflation pressure of thecompact spare tire every time youcheck the other tires. It should beinflated to:
Replace the tire when you can seethe tread wear indicator bars. Thereplacement should be the same sizeand design tire, mounted on thesame wheel. The spare tire is notdesigned to be mounted on a regularwheel, and the spare wheel is notdesigned for mounting a regular tire.
Follow these precautions:
Never exceed 50 mph (80 km/h).
This tire gives a harsher ride andless traction on some road sur-faces. Use greater caution whiledriving.
Do not mount snow chains on thecompact spare tire.
Do not use your compact sparetire on another vehicle unless it isthe same make and model.
Compact Spare Tire
188
INDICATOR LOCATION MARK
TREAD WEAR INDICATOR60 psi (420 kPa , 4.2 kgf/cm )
Park the vehicle on firm, level andnon-slippery ground. Put thetransmission in Park (automatic)or Reverse (manual). Apply theparking brake.
Turn on the hazard warning lights,and turn the ignition switch toLOCK (0). Have all thepassengers get out of the vehiclewhile you change the tire.
Take the tool kit out of the trunk.
Unscrew the wing bolt and takethe spare tire out of its well.
Open the trunk. Raise the trunkfloor mat and the trunk floor bylifting up on the back edge.
If you have a flat tire while driving,stop in a safe place to change it.Drive slowly along the shoulder untilyou get to an exit or an area that isfar away from the traffic lanes.
5.
4.
3.
2.
1.
CONTINUED
Changing a Flat TireTaking
Care
ofthe
Unexpected
189
SPARE TIRE TRUNK FLOOR
TOOL KIT JACK
The vehicle can easily roll offthe jack, seriously injuringanyone underneath.
Follow the directions forchanging a tire exactly, andnever get under the vehiclewhen it is supported only by thejack.
Turn the jack’s endcounterclockwise to loosen it, thenremove the jack.
Loosen each wheel nut 1/2 turnwith the wheel nut wrench.
Place the jack under the jackingpoint nearest the tire you need tochange. Turn the end bracketclockwise until the top of the jackcontacts the jacking point. Makesure the jacking point tab isresting in the jack notch.
6. 7. 8.
Changing a Flat Tire
190
JACK JACKING POINTS
WHEEL NUT WRENCH
CONTINUED
Use the extension and the wheelnut wrench as shown to raise thevehicle until the flat tire is off theground.
Do not attempt to forcibly pry thewheel cover off with a screwdriveror other tool. The wheel covercannot be removed without firstremoving the wheel nuts.Remove the wheel nuts, then
remove the flat tire. Handle thewheel nuts carefully; they may behot from driving. Place the flat tireon the ground with the outsidesurface facing up.
Before mounting the spare tire,wipe any dirt off the mountingsurface of the wheel and hub witha clean cloth. Wipe the hubcarefully; it may be hot fromdriving.
9. 11.
10.
DX, Value Package, and LX models
Changing a Flat TireTaking
Care
ofthe
Unexpected
191
EXTENSION
WHEELNUTS
WHEEL NUTSWHEEL COVERWHEEL NUT WRENCH
BRAKE HUB
Put on the spare tire. Put thewheel nuts back on finger-tight,then tighten them in a crisscrosspattern with the wheel nut wrenchuntil the wheel is firmly againstthe hub. Do not try to tightenthem fully.
Lower the vehicle to the groundand remove the jack.
Remove the center cap from theflat tire.
Tighten the wheel nuts securely inthe same crisscross pattern. Havethe wheel nut torque checked atthe nearest automotive servicefacility.
Tighten the wheel nuts to:
12.
13.
14. 15.On HX, Special Edition, and EXmodels in the U.S., REVERB and Simodels in Canada
Changing a Flat Tire
192
80 lbf·ft (108 N·m , 11 kgf·m)
Place the flat tire face down in thespare tire well.
Remove the spacer cone from thewing bolt, turn it over, and put itback on the bolt.
Secure the flat tire by screwingthe wing bolt back into its hole.
Store the jack in the trunk with theend bracket on the left side. Turnthe jack’s end bracket to lock it inplace. Store the tool kit.
Store the wheel cover or centercap in the trunk. Make sure it doesnot get scratched or damaged.
Lower the trunk floor, then closethe trunk lid.
16.
17.
18.
19.
20.
21.
Changing a Flat TireTaking
Care
ofthe
Unexpected
193
WING BOLT SPACERCONE
Loose items can fly around theinterior in a crash and couldseriously injure the occupants.
Store the wheel, jack, and toolssecurely before driving.
Diagnosing why the engine won’tstart falls into two areas, dependingon what you hear when you turn thekey to START (III):
You hear nothing, or almostnothing. The engine’s startermotor does not operate at all, oroperates very slowly.
You can hear the starter motoroperating normally, or the startermotor sounds like it is spinningfaster than normal, but the enginedoes not start up and run.
Check these things:
When you turn the ignition switch toSTART (III), you do not hear thenormal noise of the engine trying tostart. You may hear a clicking soundor series of clicks, or nothing at all.
Check the transmission interlock.If you have a manual transmission,the clutch pedal must be pushedall the way to the floor or thestarter will not operate. With anautomatic transmission, it must bein Park or Neutral.
Turn the ignition switch to ON (II).Turn on the headlights, and checktheir brightness. If the headlightsare very dim or do not come on atall, the battery is discharged. See
on page .
Turn the ignition switch to START(III). If the headlights do not dim,check the condition of the fuses. Ifthe fuses are OK, there isprobably something wrong withthe electrical circuit for theignition switch or starter motor.You will need a qualifiedtechnician to determine theproblem (seeon page ).
If the headlights dim noticeably orgo out when you try to start theengine, either the battery is dis-charged or the connections arecorroded. Check the condition ofthe battery and terminal connec-tions (see page ). You canthen try jump starting the vehiclefrom a booster battery (see page
).
209
184
196196
Nothing Happens or the StarterMotor Operates Very Slowly
Jump Starting
Emergency Towing
If the Engine Won’t Start
194
In this case, the starter motor’sspeed sounds normal, or even fasterthan normal, when you turn theignition switch to START (III), butthe engine does not run.
Do you have fuel? Check the fuelgauge; the low fuel indicator maynot be working.
There may be an electricalproblem, such as no power to thefuel pump. Check all the fuses(see page ).Are you using a properly coded
key? An improperly coded key willcause the immobilizer systemindicator in the instrument panelto blink rapidly (see page ).
Are you using the proper startingprocedure? Refer to
on page .
If you find nothing wrong, you willneed a qualified technician to findthe problem. See
on page .67
135
204
209
The Starter Operates Normally
Starting theEngine
EmergencyTowing
If the Engine Won’t StartTaking
Care
ofthe
Unexpected
195
+
+
Although this seems like a simpleprocedure, you should take severalprecautions.
Open the hood, and check thephysical condition of the battery.In very cold weather, check thecondition of the electrolyte. If itseems slushy or frozen, do not tryjump starting until it thaws.
You cannot start your vehicle with anautomatic transmission by pushingor pulling it.
The numbers in the illustration showyou the order to connect the jumpercables.
Connect one jumper cable to thepositive ( ) terminal on yourbattery. Connect the other end tothe positive ( ) terminal on thebooster battery.
Turn off all the electrical acces-sories: heater, A/C, stereo system,lights, etc. Put the transmission inNeutral or Park, and set theparking brake.
3.
1.
2.
To Jump Start Your Vehicle:
Jump Starting
196
BOOSTER BATTERY
A battery can explode if you donot follow the correct procedure,seriously injuring anyonenearby.
Keep all sparks, open flames,and smoking materials awayfrom the battery.
If a battery sits in extreme cold, theelectrolyte inside can f reeze.Attempting to jump start with a f rozenbattery can cause it to rupture.
-
The pointer of the vehicle’stemperature gauge should stay inthe midrange. If it climbs to the redmark, you should determine thereason (hot day, driving up a steephill, etc.).
If the vehicle overheats, youshould take immediate action. Theonly indication may be thetemperature gauge climbing to orabove the red mark. Or you maysee steam or spray coming fromunder the hood.
Connect the second jumper cableto the negative ( ) terminal onthe booster battery. Connect theother end to the grounding strapas shown. Do not connect thisjumper cable to any other part ofthe engine.
If the booster battery is in anothervehicle, have an assistant startthat vehicle and run it at a fast idle.
Start your vehicle. If the startermotor still operates slowly, checkthat the jumper cables have goodmetal-to-metal contact.
Once your vehicle is running,disconnect the negative cable fromyour vehicle, then from thebooster battery. Disconnect thepositive cable from your vehicle,then from the booster battery.
Keep the ends of the jumper cablesaway from each other and any metalon the vehicle until everything isdisconnected. Otherwise, you maycause an electrical short.
7.
6.
4.
5.
CONTINUED
Jump Starting, If the Engine Overheats
If the Engine Overheats
Taking
Care
ofthe
Unexpected
197
Driving with the temperature gaugepointer at the red mark can causeserious damage to your engine.
If you do not see steam or spray,leave the engine running, andwatch the temperature gauge. Ifthe high heat is due to overloading,the engine should start to cooldown almost immediately. If itdoes, wait until the temperaturegauge comes down to the midpoint,then continue driving.
If the temperature gauge stays atthe red mark, turn off the engine.
Look for any obvious coolant leaks,such as a split radiator hose.Everything is still extremely hot,so use caution. If you find a leak, itmust be repaired before youcontinue driving (see
on page ).
If you see steam and/or spraycoming from under the hood, turnoff the engine. Wait until you seeno more signs of steam or spray,then open the hood.
If you don’t find an obvious leak,check the coolant level in theradiator reserve tank (see page
). Add coolant if the level isbelow the MIN mark.
Safely pull to the side of the road.Put the transmission in Neutral orPark, and set the parking brake.Turn off all accessories, and turnon the hazard warning indicators.
1.
2.
3.
4.
5.
6.
126
209Emergency
Towing
If the Engine Overheats
198
Steam and spray from anoverheated engine canseriously scald you.
Do not open the hood if steamis coming out.
Using gloves or a large heavycloth, turn the radiator capcounterclockwise, without pushingdown, to the first stop. After thepressure releases, push down onthe cap, and turn it until it comesoff.
Put the radiator cap back ontightly. Run the engine, and watchthe temperature gauge. If it goesback to the red mark, the engineneeds repair (see
on page ).
If the temperature stays normal,check the coolant level in theradiator reserve tank. If it hasgone down, add coolant to theMAX mark. Put the cap back ontightly.
Start the engine, and set thetemperature control dial tomaximum heat. Add coolant to theradiator up to the base of the fillerneck. If you do not have theproper coolant mixture available,you can add plain water.Remember to have the coolingsystem drained and refilled withthe proper mixture as soon as youcan.
If there was no coolant in thereserve tank, you may need to addcoolant to the radiator. Let theengine cool down until the pointerreaches the middle of thetemperature gauge or lowerbefore checking the radiator.
7. 8.
9.
10.
11.
209Emergency
Towing
If the Engine OverheatsTaking
Care
ofthe
Unexpected
199
Removing the radiator capwhile the engine is hot cancause the coolant to spray out,seriously scalding you.
Always let the engine andradiator cool down beforeremoving the radiator cap.
Safely pull off the road, and shutoff the engine. Turn on the hazardwarning indicators.
If necessary, add oil to bring thelevel back to the full mark on thedipstick (see page ).
Immediately turn off all electricalaccessories. Try not to use otherelectrically operated controls such asthe power windows. Keep the enginerunning; starting the engine willdischarge the battery rapidly.
Go to a service station or garagewhere you can get technicalassistance.
Let the vehicle sit for a minute.Open the hood, and check the oillevel (see page ). An enginevery low on oil can lose pressureduring cornering and other drivingmaneuvers.
If the charging systemindicator comes on brightly
when the engine is running, thebattery is not being charged.
This indicator should nevercome on when the engine is
running. If it starts flashing or stayson, the oil pressure has dropped verylow or lost pressure. Serious enginedamage is possible and you shouldtake immediate action.
Start the engine, and watch the oilpressure indicator. If it does not goout within 10 seconds, turn off theengine. There is a mechanicalproblem that needs to be repairedbefore you can continue driving(see on page
).
1.
2.
3.
4.
125
159
209
Charging System IndicatorLow Oil Pressure Indicator
Emergency Towing
Low Oil Pressure Indicator, Charging System Indicator
200
Running the engine with low oilpressure can cause serious mechanicaldamage almost immediately. Turn of fthe engine as soon as you can saf ely getthe vehicle stopped.
If your vehicle battery has beendisconnected or gone dead, thesecodes are erased. It takes at leastthree days of driving under variousconditions to set the codes again.
If you have recently refueled yourvehicle, the indicator coming oncould be due to a loose or missingfuel fill cap. Tighten the cap until itclicks at least three times.Tightening the cap will not turn theindicator off immediately; it takes atleast three days of normal driving.
Your vehicle has certain ‘‘readinesscodes’’ that are part of the on-boarddiagnostics for the emissionssystems. In some states, part of theemissions testing is to make surethese codes are set. If they are notset, the test cannot be completed.
If the indicator comes onwhile driving, it means one
of the engine’s emissions controlsystems may have a problem. Eventhough you may feel no difference inyour vehicle’s performance, it canreduce your fuel economy and causeincreased emissions. Continuedoperation may cause serious damage.
If the indicator comes on repeatedly,even though it may turn off as youcontinue driving, have the vehiclechecked by your dealer as soon aspossible.
To check if they are set, turn theignition switch to ON (II), withoutstarting the engine. The MalfunctionIndicator Lamp will come on for 20seconds. If it then goes off, thereadiness codes are set. If it blinks 5times, the readiness codes are notset. If possible, do not take yourvehicle for a state emissions testuntil the readiness codes are set.Refer to State Emissions Testing formore information (see page ).222
Malfunction Indicator Lamp
Readiness Codes Taking
Care
ofthe
Unexpected
201
If you keep driving with theMalf unction Indicator Lamp on, youcan damage your vehicle’s emissionscontrols and the engine. Those repairsmay not be covered by your vehicle’swarranties.
However, if the brake pedal does notfeel normal, you should takeimmediate action. A problem in onepart of the system’s dual circuitdesign will still give you braking attwo wheels. You will feel the brakepedal go down much farther beforethe vehicle begins to slow down, andyou will have to press harder on thepedal.
If you must drive the vehicle a shortdistance in this condition, driveslowly and carefully.
Slow down by shifting to a lowergear, and pull to the side of the roadwhen it is safe. Because of the longdistance needed to stop, it ishazardous to drive the vehicle. Youshould have it towed and repaired assoon as possible (see
on page ).
The brake systemindicator normallycomes on when
you turn the ignition switch to ON(II), and as a reminder to check theparking brake. It will stay on if youdo not fully release the parkingbrake.
If the fluid level is low, take yourvehicle to a dealer, and have thebrake system inspected for leaks orworn brake pads.
If the brake system indicator comeson while driving, the brake fluid levelis probably low. Press lightly on thebrake pedal to see if it feels normal.If it does, check the brake fluid levelthe next time you stop at a servicestation (see page ).
If the ABS indicator comes on withthe brake system indicator, haveyour vehicle inspected by yourdealer immediately.
168
209
On models equipped with ABS
EmergencyTowing
Brake System Indicator
202
CanadaU.S.
Use a screwdriver or coin toremove the round plug in thecenter of the headliner.
Remove the wrench. Reinstall theround plug.
If the electric motor will not closethe moonroof, do the following:
Check the fuse for the moonroofmotor (see page ). If the fuseis blown, replace it with one of thesame or lower rating.
Try closing the moonroof. If thenew fuse blows immediately or themoonroof motor still does notoperate, you can close themoonroof manually.
Get the moonroof wrench out ofthe tool kit in the trunk.
Insert the moonroof wrench intothe socket behind the plug. Turnthe wrench until the moonroof isfully closed.
If you need to close the moonroofmanually, it means the moonroofopening/closing function isdeveloping a problem. Have yourvehicle checked by your dealer.
5.
6.
4.
1.
2.
3.
208
If equipped
Closing the MoonroofTaking
Care
ofthe
Unexpected
203
ROUND PLUG
SOCKET
MOONROOFWRENCH
Turn the ignition switch to LOCK(0). Make sure the headlights andall other accessories are off.
Remove the cover from the fusebox.
The vehicle’s fuses are contained intwo fuse boxes.
The under-hood fuse box is in theengine compartment on thepassenger’s side next to the battery.To open it, push the tabs as shown.
If something electrical in yourvehicle stops working, check for ablown fuse first. Determine from thechart on pages and , or thediagram on the fuse box lid, whichfuse or fuses control that device.Check those fuses first, but check allthe fuses before deciding that ablown fuse is the cause. Replace anyblown fuses, and check if the deviceworks.
The interior fuse box is underneaththe steering column. To open it, turnthe knobs as shown.
1.
2.
207 208
Fuses
Checking and Replacing Fuses
204
UNDER-HOOD
TAB
INTERIOR
Check the smaller fuses in theunder-hood fuse box and all thefuses in the interior fuse box bypulling out each one with the fusepuller provided in the under-hoodfuse box.
Look for a burned wire inside thefuse. If it is burned, replace it withone of the spare fuses of the samerating or lower.
Check each of the large fuses inthe under-hood fuse box bylooking through the top at the wireinside. Removing these fusesrequires a Phillips-head screw-driver.
5.4.3.
CONTINUED
FusesTaking
Care
ofthe
Unexpected
205
BLOWN
FUSE PULLER
FUSE
BLOWN
If the replacement fuse of thesame rating blows in a short time,there is probably a seriouselectrical problem in your vehicle.Leave the blown fuse in thatcircuit and have your vehiclechecked by a qualified mechanic.
If you cannot drive the vehiclewithout fixing the problem, and youdo not have a spare fuse, take a fuseof the same rating or a lower ratingfrom one of the other circuits. Makesure you can do without that circuittemporarily (such as the accessorypower socket or radio).
If you replace the blown fuse with aspare fuse that has a lower rating, itmight blow out again. This does notindicate anything wrong. Replace thefuse with one of the correct rating assoon as you can.
If the radio fuse is removed, theaudio system will disable itself. Thenext time you turn on the radio youwill see ‘‘ ’’ (except formodels with in-dash CD changer)/‘‘CODE’’ (on models with in-dash CDchanger) in the frequency display.Use the preset buttons to enter thefive-digit code (see page ).
When the audio system is disabled,the clock setting in the audio systemwill be canceled. You will need toreset the clock according to theinstructions in the Features sectionon this owner’s manual.
6.
114
Standard for Value Package, HX, LX, EXand Special Edition models in the U.S.,and DX Special Edition, REVERB, LXand Si models in Canada
On all models
Fuses
206
Replacing a f use with one that has ahigher rating greatly increases thechances of damaging the electricalsystem. If you do not have areplacement f use with the proper ratingf or the circuit, install one with a lowerrating.
-
-
-
CONTINUED
No. Amps. Circuits Protected
123456789
1011121314151617181920
20 A15 A
7.5 A20 A10 A15 A15 A20 A10 A40 A40 A40 A40 A40 A20 A20 A20 A
80 A40 A
Condenser FanSmall LightInterior LightCooling FanHazard, Turn SignalsFI ECU (ECM/PCM)Horn, Brake LightABS F/SBack UpABS MotorRear DefrosterHeater MotorPower WindowOptionLeft HeadlightDoor LockRight HeadlightNot UsedBatteryIgnition 1Spare Fuses21 25 7.5 A 30 A
Fuse LocationsTaking
Care
ofthe
Unexpected
207
UNDER-HOOD FUSE BOX
-
-
-
-
-
*
*
*
No. Amps. Circuits Protected
No. Amps. Circuits Protected
: On Canadian models
12345
15 A20 A10 A10 A
Ignition CoilLAF HeaterDaytime Running LightsAlternatorNot Used
6789
10111213141516171819202122232425
7.5 A20 A
7.5 A10 A
7.5 A7.5 A7.5 A10 A10 A10 A
15 A15 A
7.5 A20 A
20 A20 A
Power Window RelayMoonroofAccessory, RadioSIDE SRSMeterABSDaytime Running LightsSRSPower Mirrors(Security)Not UsedFuel PumpAccessory Power SocketTurn Signal LightsFront WipersNot UsedFront Right Power WindowFront Left Power WindowNot UsedNot Used
Fuse Locations
208
INTERIOR FUSE BOX
-
-
CONTINUED
If, due to damage, your vehicle mustbe towed with the front wheels onthe ground, do the following:
If your vehicle needs to be towed,call a professional towing service ororganization. Never tow your vehiclewith just a rope or chain. It is verydangerous. There are two ways totow your vehicle.
The operatorloads your vehicle on the back of atruck.
The towtruck uses two pivoting arms that gounder the tires (front or rear) and liftthem off the ground. The other twotires remain on the ground.
Release the parking brake.Shift the transmission to Neutral.
Release the parking brake.Start the engine.Shift to D, then to N.Turn off the engine.
With the front wheels on the ground,it is best to tow the vehicle no fartherthan 50 miles (80 km), and keep thespeed below 35 mph (55 km/h).
If your vehicle is equipped with afront spoiler, remove it beforetowing so it is not damaged.
Manual Transmission and ContinuouslyVariable Transmission (CVT):
Automatic Transmission:
Emergency Towing
Flat-bed Equipment
Wheel-lif t Equipment
This is the best way to trans-port your vehicle.
This isan acceptable way to tow yourvehicle.
Taking
Care
ofthe
Unexpected
209
Improper towing preparation willdamage the transmission. Follow theabove procedure exactly. If you cannotshif t the transmission or start theengine (automatic transmission), yourvehicle must be transported with thef ront wheels of f the ground.
If you decide to tow your vehiclewith all four wheels on the ground,make sure you use a properly-designed and attached tow bar.Prepare the vehicle for towing asdescribed previously, and leave theignition switch in the ACCESSORY(I) position so the steering wheeldoes not lock. Make sure the radioand any items plugged into theaccessory power socket are turnedoff so they do not run down thebattery.
Emergency Towing
210
Trying to lif t or tow your vehicle by thebumpers will cause serious damage.The bumpers are not designed tosupport the vehicle’s weight.
The steering system can be damaged ifthe steering wheel is locked. Leave theignition switch in the ACCESSORY (I)position, and make sure the steeringwheel turns f reely bef ore you begintowing.
The diagrams in this section giveyou the dimensions and capacities ofyour vehicle, and the locations of theidentification numbers. It alsoincludes information you shouldknow about your vehicle’s tires andemissions control systems.
................Identification Numbers . 212................................Specifications . 214
DOT Tire Quality Grading......................(U.S. Vehicles) . 216
Uniform Tire Quality..................................Grading . 216.................................Treadwear . 216
......................................Traction . 216.............................Temperature . 217
.................................Tire Labeling . 218
.......................Emissions Controls . 219.....................The Clean Air Act . 219
Crankcase Emissions Control....................................System . 219
Evaporative Emissions Control....................................System . 219
Onboard Refueling Vapor................................Recovery . 219
...Exhaust Emissions Controls . 220....................PGM-FI System . 220
Ignition Timing Control................................System . 220
Exhaust Gas Recirculation....................(EGR)System . 220
Three Way Catalytic...........................Converter . 220
....................Replacement Parts . 220..Three Way Catalytic Converter . 221
..............State Emissions Testing . 222
Technical InformationTechnicalInform
ation
211
Your vehicle has several identifyingnumbers located in various places.
The vehicle identification number(VIN) is the 17-digit number yourdealer uses to register your vehiclefor warranty purposes. It is alsonecessary for licensing and insuringyour vehicle. The easiest place tofind the VIN is on a plate fastened tothe top of the dashboard. You cansee it by looking through thewindshield on the driver’s side. It isalso on the certification labelattached to the driver’s doorjamb,and is stamped on the enginecompartment bulkhead. The VIN isalso provided in bar code on thecertification label.
Identif ication Numbers
212
VEHICLE IDENTIFICATION NUMBER
CERTIFICATION LABEL
The engine number is stamped intothe engine block. It is on the front.
The transmission number is on alabel on top of the transmission.
Identif ication NumbersTechnicalInform
ation
213
AUTOMATIC TRANSMISSION NUMBER
ENGINE NUMBER
MANUAL TRANSMISSIONNUMBER
* *
*
*
*
*
*
*
*
*
*
*
*
*
*
*
**
*
+
+
Specifications
214
Dimensions
Weights
Engine
Capacities
Capacities
174.7 in (4,438 mm)66.7 in (1,695 mm)55.1 in (1,399 mm)103.1 in (2,620 mm)57.9 in (1,470 mm)57.9 in (1,470 mm)
2.95 x 3.72 in (75.0 x 94.4 mm)102 cu-in (1,668 cm )
9.59.9
LengthWidthHeightWheelbaseTrack
Gross vehicle weight rating See the certification label attachedto the driver’s doorjamb.
Water cooled 4-strokeSOHC , SOHC VTEC
4-cylinder gasoline engine
NGK:DENSO:
Type
Bore x StrokeDisplacementCompression ratio
Spark plugs
Spark plug Gap
PZFR6F-11PKJ20CR-M11
0.04 in (1.1 mm)
Enginecoolant
Engine oil
Automatictransmissionfluid
13.2 US gal (50 )Fuel tank
1.03 US gal (3.9 )1.00 US gal (3.8 )1.00 US gal (3.8 )
1.32 US gal (5.0 )1.29 US gal (4.9 )1.29 US gal (4.9 )
3.4 US qt (3.2 )3.7 US qt (3.5 )3.2 US qt (3.0 )3.5 US qt (3.3 )4.4 US qt (4.2 )1.6 US qt (1.5 )1.7 US qt (1.6 )2.9 US qt (2.7 )3.4 US qt (3.2 )6.3 US qt (6.0 )6.0 US qt (5.7 )2.6 US qt (2.5 )4.8 US qt (4.5 )
Including the coolant in the reserve tank and that remaining inthe engine.Reserve tank capacity: 0.108 US gal (0.41 )Excluding the oil remaining in the engine.
FrontRear
Approx.7 :
1 :
2 :
U.S: DX, Value Package, LX, LX Special EditionCanada: DX, LX, REVERBU.S.: HX, EX, EX Special EditionCanada: Si
ChangeManualAutomaticCVT
TotalManualAutomaticCVT
ChangeIncludingfilterWithout filter
TotalChangeTotalChange
Total
U.S. Vehicles
HX
3 :
4 :5 :
6 :
U.S.: DX, Value Package, LX, LX Special EditionCanada: DX, LX, REVERBU.S.: HX, EX, EX Special Edition Canada: Si
1 2
1
2
3
4
5
6
5
6
7
7
Manual trans-mission fluid
Canada VehiclesWindshieldwasher reservoir0
0.1 mm
- -
-
- -
****
*
---
----------
--
*
*
*
*
*
*
*
*
*
*
SpecificationsTechnicalInform
ation
215
Air Conditioning Fuses
Alignment
Tires
Lights
Battery
HFC-134a (R-134a)17.6 19.4 oz (500 550 g)
12 V12 V
60 W
2°14’45’
0°
0.00 in (0.0 mm)
P185/65R15 86HP185/70R14 87S
0.08 in ( 2.0 mm)
12 V51 W
60 psi (420 kPa , 4.2 kgf/cm )30 psi (210 kPa , 2.1 kgf/cm )
T125/70D15 95MT115/70D14 88MP195/60R15 87H
Refrigerant typeCharge quantityLubricant oil type
Interior
Under-hood
Toe-in
Camber
Caster
Size
Pressure
24/2.2 CP
See page 208 or the fuse labelattached to the inside of the fusebox door under the steeringcolumn.See page 207 or the fuse boxcover.Headlights (HI)
Headlights (LO)Front turn signal/Side marker/Parking lightRear turn signal lightsStop/TaillightsBack-up lightsHigh-mount stop lightLicense plate lightsCeiling lightFront ceiling lightSpotlights
Trunk light
SP-10
12 V 5 W8 W12 V
12 V 5 W5 W12 V10 W12 V3 CP12 V21 W12 V18 W12 V21/5 W12 V21 W12 V
Capacity12 V12 V
38 AH/5 HR36 AH/5 HR
FrontRearFrontRearFront
3 :4 :5 :6 :
7 :
(HB3)
Front/Rear
Spare
Front/RearSpare
(HB4)
U.S.: DX, Value Package, HX Canada: DXCanada: LXU.S.: LX, EX, Special Edition Canada: Si, REVERB
1 : U.S.: EX, EX Special EditionCanada : Si
2 : LX, LX Special Edition
U.S.: DX, Value Package, HX, LX and LX Special EditionCanada : DX, LX, REVERBU.S.: LX with ABS, EX, Special EditionCanada: LX with ABS, Si
1
1
2
3
4
5
6
7
-The tires on your vehicle meet allU.S. Federal Safety Requirements.All tires are also graded fortreadwear, traction, and temperatureperformance according toDepartment of Transportation(DOT) standards. The followingexplains these gradings.
Quality grades can be found whereapplicable on the tire sidewallbetween the tread shoulder and themaximum section width. Forexample:
The treadwear grade is a compara-tive rating based on the wear rate ofthe tire when tested under controlledconditions on a specified governmenttest course. For example, a tiregraded 150 would wear one and one-half (1 1/2) times as well on thegovernment course as a tire graded100. The relative performance oftires depends upon the actual condi-tions of their use, however, and maydepart significantly from the normdue to variations in driving habits,service practices, and differences inroad characteristics and climate.
The traction grades, from highest tolowest, are AA, A, B, and C. Thosegrades represent the tire’s ability tostop on wet pavement as measuredunder controlled conditions onspecified government test surfacesof asphalt and concrete. A tiremarked C may have poor tractionperformance.
All passenger car tires must conformto Federal Safety Requirements inaddition to these grades.
Warning: The traction gradeassigned to this tire is based onstraight-ahead braking traction tests,and does not include acceleration,cornering, hydroplaning, or peaktraction characteristics.
Uniform Tire Quality Grading
Treadwear 200Traction AATemperature A
Treadwear Traction AA, A, B, C
DOT Tire Quality Grading (U.S. Vehicles)
216
-The temperature grades are A (thehighest), B, and C, representing thetire’s resistance to the generation ofheat and its ability to dissipate heatwhen tested under controlledconditions on a specified indoorlaboratory test wheel. Sustained hightemperature can cause the materialof the tire to degenerate and reducetire life, and excessive temperaturecan lead to sudden tire failure. Thegrade C corresponds to a level ofperformance which all passenger cartires must meet under the FederalMotor Vehicle Safety Standard No.109. Grades B and A representhigher levels of performance on thelaboratory test wheel than theminimum required by law.
Warning: The temperature grade forthis tire is established for a tire thatis properly inflated and not over-loaded. Excessive speed, underinfla-tion, or excessive loading, eitherseparately or in combination, cancause heat buildup and possible tirefailure.
Temperature A, B, C
DOT Tire Quality Grading (U.S. Vehicles)TechnicalInform
ation
217
-
-
-
-
-
-
-
-
-
-
-
-
-
The tires that came on your vehiclehave a number of markings. Thoseyou should be aware of are describedbelow.
Whenever tires are replaced, theyshould be replaced with tires of thesame size. Following is an exampleof tire size with an explanation ofwhat each component means.
Vehicle type (P indicatespassenger vehicle).
Tire width in millimeters.
Aspect ratio (the tire’s sectionheight as a percentage of itswidth).
Tire construction code (Rindicates radial).
Rim diameter in inches.
Speed symbol (analphabetical code indicatingthe maximum speed rating).
Load index (a numerical codeassociated with the maximumload the tire can carry).
Tire type code.
Date of manufacture.
Max Press The maximum airpressure the tire can hold.
Max Load The maximum load thetire can carry at maximum airpressure.Tire Identification Number (TIN) is
a group of numbers and letters thatlook like the following example TIN.
This indicates that the tiremeets all requirements ofthe U.S. Department ofTransportation.
Manufacturer’sidentification mark.
B97R
FW6X
2202
DOT
R
P
195
60
15
87
HTire Size
Maximum Tire Pressure
Maximum Tire Load
Tire Identif ication Number
Tire Labeling
218
P195/60R15 87H
DOT B97R FW6X 2202
*
*
The burning of gasoline in yourvehicle’s engine produces several by-products. Some of these are carbonmonoxide (CO), oxides of nitrogen(NOx) and hydrocarbons (HC).Gasoline evaporating from the tankalso produces hydrocarbons. Con-trolling the production of NOx, CO,and HC is important to the environ-ment. Under certain conditions ofsunlight and climate, NOx and HCreact to form photochemical ‘‘smog.’’Carbon monoxide does not contri-bute to smog creation, but it is apoisonous gas.
The United States Clean Air Actsets standards for automobileemissions. It also requires thatautomobile manufacturers explain toowners how their emissions controlswork and what to do to maintainthem. This section summarizes howthe emissions controls work.Scheduled maintenance is on page
.
In Canada, Honda vehicles complywith the Canadian emissionrequirements, as specified in anagreement with EnvironmentCanada, at the time they aremanufactured.
Your vehicle has a positivecrankcase ventilation system. Thiskeeps gasses that build up in theengine’s crankcase from going intothe atmosphere. The positive
crankcase ventilation valve routesthem from the crankcase back to theintake manifold. They are thendrawn into the engine and burned.
As gasoline evaporates in the fueltank, an evaporative emissionscontrol canister filled with charcoaladsorbs the vapor. It is stored in thiscanister while the engine is off. Afterthe engine is started and warmed up,the vapor is drawn into the engineand burned during driving.
The onboard refueling vaporrecovery (ORVR) system capturesthe fuel vapors during refueling. Thevapors are adsorbed in a canisterfilled with activated carbon. Whiledriving, the fuel vapors are drawninto the engine and burned off.
151
The Clean Air Act
Crankcase Emissions ControlSystem
Evaporative Emissions ControlSystem
Onboard Refueling VaporRecovery
Emissions ControlsTechnicalInform
ation
219
The emissions control systems aredesigned and certified to work to-gether in reducing emissions tolevels that comply with the Clean AirAct. To make sure the emissionsremain low, you should use only newHonda replacement parts or theirequivalent for repairs. Using lowerquality parts may increase theemissions from your vehicle.
The emissions control systems arecovered by warranties separate fromthe rest of your vehicle. Read yourwarranty manual for more informa-tion.
The exhaust emissions controlsinclude four systems: PGM-FI,ignition timing control, exhaust gasrecirculation and three way catalyticconverter. These four systems worktogether to control the engine’scombustion and minimize theamount of HC, CO, and NOx thatcomes out the tailpipe. The exhaustemissions control systems areseparate from the crankcase andevaporative emissions controlsystems.
The PGM-FI system uses sequentialmultiport fuel injection. It has threesubsystems: air intake, enginecontrol, and fuel control. Thepowertrain control module (PCM) inautomatic transmission vehicles orthe engine control module (ECM) inmanual transmission vehicles usesvarious sensors to determine howmuch air is going into the engine. It
then controls how much fuel to injectunder all operating conditions.
The three way catalytic converter isin the exhaust system. Throughchemical reactions, it converts HC,CO, and NOx in the engine’s exhaustto carbon dioxide (CO ), nitrogen(N ), and water vapor.
The exhaust gas recirculation (EGR)system takes some of the exhaustgas and routes it back into the intakemanifold. Adding exhaust gas to theair/fuel mixture reduces the amountof NOx produced when the fuel isburned.
This system constantly adjusts theignition timing, reducing the amountof HC, CO, and NOx produced.
2
2
Replacement PartsExhaust Emissions Controls
PGM-FI System
Three Way Catalytic Converter
Exhaust Gas Recirculation (EGR)System
Ignition Timing Control System
Emissions Controls
220
The three way catalytic convertercontains precious metals that serveas catalysts, promoting chemicalreactions to convert the exhaustgasses without affecting the metals.The catalytic converter is referred toas a three-way catalyst, since it actson HC, CO, and NOx. A replacementunit must be an original Honda partor its equivalent.
The three way catalytic convertermust operate at a high temperature
for the chemical reactions to takeplace. It can set on fire any com-bustible materials that come near it.Park your vehicle away from highgrass, dry leaves, or other flamma-bles.
Always use unleaded gasoline.Even a small amount of leadedgasoline can contaminate thecatalyst metals, making the threeway catalytic converter ineffective.
Keep the engine tuned-up.
Have your vehicle diagnosed andrepaired if it is misfiring, back-firing, stalling, or otherwise notrunning properly.
A defective three way catalyticconverter contributes to air pollution,and can impair your engine’s per-formance. Follow these guidelines toprotect your vehicle’s three waycatalytic converter.
Three Way Catalytic ConverterTechnicalInform
ation
221
THREE WAY CATALYTIC CONVERTER THREE WAY CATALYTIC CONVERTERSTHREE WAY CATALYTIC CONVERTER
U.S. EX and Canadian Si models U.S. DX, LX and Canadian DX, LX,REVERB models
U.S. HX
If you take your vehicle for a stateemissions test shortly after thebattery has been disconnected orgone dead, it may not pass the test.This is because of certain ‘‘readinesscodes’’ that must be set in the on-board diagnostics for the emissionssystems. These codes are erasedwhen the battery is disconnected,and set again only after several daysof driving under a variety ofconditions.
If the testing facility determines thatthe readiness codes are not set, youwill be requested to return at a laterdate to complete the test. If you mustget the vehicle retested within thenext two or three days, you cancondition the vehicle for retesting bydoing the following.
Make sure the gas tank is nearly,but not completely full (around3/4).
Make sure the vehicle has beenparked with the engine off for 8hours or more.
Make sure the ambienttemperature is between 20° and95°F.
Without touching the acceleratorpedal, start the engine, and let itidle for 20 seconds.
Keep the vehicle in Park(automatic transmission) orNeutral (manual transmission).Increase the engine speed to 2,000rpm, and hold it there until thetemperature gauge rises to at least1/4 of the scale (about 3 minutes).
Select a nearby lightly traveledmajor highway where you canmaintain a speed of 50 to 60 mph(80 to 97 km/h) for at least 20minutes. Drive on the highway inD (A/T) or 5th (M/T). Do not use
the cruise control. When trafficallows, drive for 90 secondswithout moving the acceleratorpedal. (Vehicle speed may varyslightly; this is okay.) If you cannotdo this for a continuous 90seconds because of trafficconditions, drive for at least 30seconds, then repeat it two moretimes (for a total of 90 seconds).
Then drive in city/suburbantraffic for at least 10 minutes.When traffic conditions allow, letthe vehicle coast for severalseconds without using theaccelerator pedal or the brakepedal.
If the testing facility determines thereadiness codes are still not set, seeyour dealer.
Testing of Readiness Codes
State Emissions Testing
222
Customer Service................................Information . 224
....................Warranty Coverages . 225Reporting Safety Defects
..........................(U.S. Vehicles) . 226.....................Authorized Manuals . 227
Warranty and Customer RelationsW
arrantyand
Custom
erR
elations
223
Honda dealership personnel aretrained professionals. They shouldbe able to answer all your questions.If you encounter a problem that yourdealership does not solve to yoursatisfaction, please discuss it withthe dealership’s management. Theservice manager or general managercan help. Almost all problems aresolved in this way.
U.S. Owners:
Canadian Owners:
If you are dissatisfied with thedecision made by the dealership’smanagement, contact your HondaCustomer Service Office.
When you call or write, please giveus this information:
In Puerto Rico and the U.S. VirginIslands:
Vehicle Identification Number(see page )
Name and address of the dealerwho services your vehicle
Date of purchase
Mileage on your vehicle
Your name, address, and tele-phone number
A detailed description of theproblem
Name of the dealer who sold thevehicle to you
212
Customer Service Information
224
CUSTOMER RELATIONS
RELATIONS AVEC LA CLIENTÉLE
American Honda Motor Co., Inc.Automobile Customer ServiceMail Stop 500-2N-7A1919 Torrance BoulevardTorrance, California 90501-2746
Tel: (800) 999-1009
Honda Canada Inc.715 Milner AvenueToronto, ONM1B 2K8
Tel: 1-888-9-HONDA-9Fax: Toll-free 1-877-939-0909
Toronto (416) 287-4776
Bella InternationalP.O. Box 190816San Juan, PR 00919-0816
Tel: (787) 250-4327
-
-
-
-
-
-
-
-
-
Your new vehicle is covered by thesewarranties:
covers your new vehicle, except forthe battery, emissions controlsystems and accessories, againstdefects in materials andworkmanship.
a seatbelt that fails to function properly iscovered for the useful life of thevehicle.
all exterior body panels arecovered for rust-through from theinside for the specified time periodwith no mileage limit.
provides proratedcoverage for a replacement batterypurchased from your dealer.
providescoverage for as long as the pur-chaser of the muffler owns thevehicle.
these twowarranties cover your vehicle’semissions control systems. Time,mileage, and coverage areconditional. Please read yourwarranty manual for exactinformation.
Honda Accessories are coveredunder this warranty. Time andmileage limits depend on the type ofaccessory and other factors. Pleaseread your warranty manual fordetails.
covers all Hondareplacement parts against defects inmaterials and workmanship.
Restrictions and exclusions apply toall these warranties. Please read the2005 Honda Warranty Informationbooklet that came with your vehiclefor precise information on warrantycoverages. Your vehicle’s originaltires are covered by theirmanufacturer. Tire warranty infor-mation is in a separate booklet.
Please refer to the 2005 WarrantyManual that came with your vehicle.
this warranty gives upto 100 percent credit toward areplacement battery.
Warranty Coverages
U.S. Owners
Canadian Owners
New Vehicle Limited Warranty
Seat Belt Limited Warranty
Rust Perforation Limited Warranty
Replacement Battery LimitedWarranty
Replacement Muffler LifetimeLimited Warranty
Emissions Control Systems DefectsWarranty and EmissionsPerformance Warranty
Accessory Limited Warranty
Replacement Parts LimitedWarranty
Original Equipment Battery LimitedWarranty
Warranty
andC
ustomer
Relations
225
If you believe that your vehicle has adefect which could cause a crash orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying American Honda MotorCo., Inc.
If NHTSA receives similar com-plaints, it may open an investigation,and if it finds that a safety defectexists in a group of vehicles, it mayorder a recall and remedy campaign.However, NHTSA cannot becomeinvolved in individual problemsbetween you, your dealer, orAmerican Honda Motor Co., Inc.
To contact NHTSA, you may eithercall the Auto Safety Hotline toll-freeat 1-800-424-9393 (or 366-0123 inWashington D.C. area) or write to:NHTSA, U.S. Department ofTransportation, Washington,D.C. 20590. You can also obtainother information about motorvehicle safety from the Hotline.
Reporting Safety Defects (U.S. Vehicles)
226
-
*
*
*
*2005
HON
Valid only for sales within the United States. Canadianowners should contact their authorized Honda dealer.The publications shown below can be purchased from Helm
Incorporated. You can order in any of three ways:
If you are interested in other years or models, contact Helm Inc.at 1-800-782-4356.
Detach and mail the order form on the right half of this pageCall Helm Inc. at 1-800-782-4356Go online at
(credit card orders only)
Purchasing Factory Authorized Manuals (U.S. only)
Authorized ManualsA
uthorizedM
anuals
227
ORDER TOLL FREE: 1-800-782-4356
OR
(NOTE: For Credit Card Holder Orders Only)
MINIMUM CREDIT CARD PURCHASE $10.00
Price
Each
$70.00
$50.00
$44.00
$34.00
$12.00
$12.00
FREE
Publication
Form Number
61S5C01
61S5C00EL
61S5A30
31S5P640
31S5AM00
31S5PQ20
HON-R
Form Description
2001-2005 Honda Civic 2/4 Door
Service Manual
2001-2005 Honda Civic 2/4 Door
Electrical Troubleshooting Manual
2001-2005 Honda Civic 2/4 Door
Body Repair Manual
2005 Honda Civic 2 Door
Owner’s Manual
2005 Honda Civic
Honda Service History
2005 Honda Civic 2 Door
Quick Start Guide
Order Form for Previous Years-
Indicate Year and Model Desired
PUBLICATION NUMBERVEHICLE MODEL
Name YearQty
Price
Each
Total
Price
GRAND TOTAL
HANDLING CHARGE
Mich. Purchases
Add 6% Sales Tax
TOTAL MATERIAL
$6.95
Monday-Friday 8:00 A.M. 6:00 P.M. EST
By completing this form you can order the materials desired. You canpay by check or money order, or charge to your credit card. Mail toHelm Incorporated at the address shown on the back of the order form.
Prices are subject to change withoutnotice and without incurring obligation.
Orders are mailed within 10 days. Pleaseallow adequate time for delivery.
Prices are subject to change without notice and without incurring obligation.
www. helminc. com
-
-
-
SHIP
TO
PAYMENT
This manual covers maintenance and recommendedprocedures for repair to engine and chassis components.It is written for the journeyman mechanic, but is simpleenough for most mechanically-inclined owners to under-stand.
This manual describes the procedures involved in thereplacement of damaged body parts.
This manual complements the service manual byproviding in-depth troubleshooting information for eachelectrical circuit in your vehicle.
Authorized Manuals
Service Manual:
Electrical Troubleshooting Manual:
Body Repair Manual:
228
NOTE: Dealers and Companies please provide dealer or company name,and also the name of the person to whose attention the shipment shouldbe sent. For purchases outside U.S.A. please write to the address shownbelow for a quotation.
P.O. BOX 07280·DETROIT, MICHIGAN 48207·1-800-782-4356
Customer Name Attention
Apartment Number
State & Zip CodeCity
Daytime Telephone Number
Check or money order enclosed payable to Helm Inc U.S. funds only.Do not send cash
MasterCard
VISA Check here if your billing address is differentfrom the shipping address shown above.
Account Number Expiration: Mo. Yr.
CUSTOMER SIGNATURE DATE
Street Address No P.O. Box Number
( )
These Publications cannot be returned for credit without receiving advance authorization within 14days of delivery. On returns, a restocking fee may be applied against the original order.
CONTINUED
BatteryCharging System
...........................Indicator . 54, 200............................Jump Starting . 196
..............................Maintenance . 184............................Specifications . 215
..............................Before Driving . 121....................................Belts, Seat . 8, 18
...........................Beverage Holders . 83..................................Booster Seats . 42
Brakes...........Anti-lock System (ABS) . 147
.............Break-in, New Linings . 122....................Bulb Replacement . 173
...........................................Fluid . 168.........................................Parking . 81
..........................System Design . 146.................System Indicator . 55, 202........................Wear Indicators . 146
.............................Braking System . 146.................Break-in, New Vehicle . 122
..Brightness Control, Instruments . 63........................Brights, Headlights . 62
Bulb Replacement..........................Back-up Lights . 173
..............................Brake Lights . 173................Front Parking Lights . 172
........Front Side Marker Lights . 172.................................Headlights . 170
.........High-mount Brake Light . 174............................Specifications . 215
....................Turn Signal Lights . 172..............................Bulbs, Halogen . 170
............................Capacities Chart . 214.............Carbon Monoxide Hazard . 45
....Accessories and Modificatons . 128ACCESSORY (Ignition Key
.......................................Position) . 68...............Accessory Power Socket . 85
................Adding Engine Coolant . 162....................Additives, Engine Oil . 160
.......Adjusting the Steering Wheel . 65.........Advice for Pregnant Women . 16
...............................Airbag (SRS) . 9, 21................Air Conditioning System . 88
............................................Usage . 89.......................Air Pressure, Tires . 178
..................High Speed Driving . 179.........................Normal Driving . 179.......................Alcohol in Gasoline . 122
......................................Antifreeze . 162Anti-lock Brakes (ABS)
...............................Indicator . 55, 147...................................Operation . 147
..............Anti-theft, Audio System . 114Anti-theft Steering Column
..............................................Lock . 68..................................Audio System . 92
.Automatic Seat Belt Tensioners . 119
.............Automatic Speed Control . 117..............Automatic Transmission . 138
..........................Capacity, Fluid . 214...............Checking Fluid Level . 165
.......................................Shifting . 138Shift Lever Position
...............................Indicators . 138................Shift Lever Positions . 138
....................Shift Lock Release . 141
Index
A
B
C
IND
EX
I
................DANGER, Explanation of . ii...................................Dashboard . 3, 50
................Daytime Running Lights . 62Daytime Running Lights
.......................................Indicator . 55.................................Dead Battery . 196
............Defects, Reporting Safety . 226................Defogger, Rear Window . 64................Defrosting the Windows . 91
....................................Dimensions . 214...............Dimming the Headlights . 62
Dipstick..........Automatic Transmission . 165
..................................Engine Oil . 125
.............................Carrying Cargo . 130Cassette Player
............................................Care . 113...................................Operation . 111
..............CAUTION, Explanation of . ii.........................................CD Care . 108
.....................................CD Changer . 99.....CD Changer Error Messages . 110
.........................................CD Player . 99.........CD Player Error Messages . 109
....................................Ceiling Light . 86........................Certification Label . 212
.................................Chains, Tires . 183....................Changing a Flat Tire . 189
Changing Oil........................................How to . 160......................................When to . 153
...Charging System Indicator . 54, 200............Checklist, Before Driving . 134
.....................................Child Safety . 27..............................Booster Seats . 42
...................................Child Seats . 34Important Safety
.........................Reminders . 27, 30..........................................Infants . 32
............................Large Children . 41
.........................................LATCH . 36......................Risks with Airbags . 28
.............................Small Children . 33.........................................Tethers . 40
...........................Warning Labels . 46.........Where Should a Child Sit? . 28
Child Seats......................................Installing . 35
...........................Lower Anchors . 36......................................Selecting . 34
................Tether Anchor Points . 40Claning
...................................Seat Belts . 174..............................................Clock . 115
...................................Clutch Fluid . 168........................CO in the Exhaust . 220
........................................Coat Hook . 84............Cold Weather, Starting in . 135
......................Compact Spare Tire . 188...................Console Compartment . 83.................Consumer Information . 224
Continuously Variable Transmission.........................................(CVT) . 142
.............Controls, Instruments and . 49Coolant
........................................Adding . 162
....................................Checking . 126.........................Proper Solution . 162
...................Temperature Gauge . 59Crankcase Emissions Control
........................................System . 219................Cruise Control Indicator . 56............Cruise Control Operation . 117
.....................................Cup Holders . 83....Customer Service Information . 224
Index
D
II
*
CONTINUED
..........................Directional Signals . 62........Disc Brake Wear Indicators . 146
.......................................Disc Care . 108.....................Disposal of Used Oil . 161
Doors..............Locking and Unlocking . 69
......................Power Door Locks . 69........DOT Tire Quality Grading . 216
Downshifting, Manual.............................Transmission . 136
...........Driver and Passenger Safety . 5...........................................Driving . 133
....................................Economy . 127..................Dust and Pollen Filter . 176
..............................Economy, Fuel . 127..................................Emergencies . 187
.............Battery, Jump Starting . 196...........Brake System Indicator . 202
................Changing a Flat Tire . 189.....Charging System Indicator . 200
..................Checking the Fuses . 204.........Hazard Warning Flashers . 64
............................Jump Starting . 196
.....Low Oil Pressure Indicator . 200...Malfunction Indicator Lamp . 201...Manually Closing Moonroof . 203
..................Overheated Engine . 197.......................................Towing . 209
...........................Emergency Brake . 81......................Emergency Flashers . 64
......................Emergency Towing . 209............Emergency Trunk Opener . 70
.......................Emissions Controls . 219.............Emissions Testing, State . 222
Engine............Adding Engine Coolant . 162
....Coolant Temperature Gauge . 59.........................If It Won’t Start . 194
Malfunction Indicator................................Lamp . 54, 201
........Oil Pressure Indicator . 54, 200.............................Oil, Synthetic . 160
..............Oil, What Kind to Use . 159...............................Overheating . 197
............................Specifications . 214
............Speed Limiter . 137, 140, 144.......................................Starting . 135
......................Ethanol in Gasoline . 122.Evaporative Emissions Controls . 219
...............................Exhaust Fumes . 45Expectant Mothers, Use of Seat
........................................Belts by . 16
......................................Fan Control . 89...........................................Features . 87
....................Filling the Fuel Tank . 123Filters
.........................Dust and Pollen . 176...............................................Oil . 160
.............Flashers, Hazard Warning . 64...................Flat Tire, Changing a . 189
Fluids..........Automatic Transmission . 165
..........................................Brake . 168.........................................Clutch . 168
..............Manual Transmission . 167..........................Power Steering . 169
..................Windshield Washer . 164FM Stereo Radio
.....................................Reception . 97...........................Folding Rear Seat . 76
Index
E
F
IND
EX
III
.............Halogen Headlight Bulbs . 170..............Hazard Warning Flashers . 64
Headlights........................................Aiming . 170
............Daytime Running Lights . 62..................High Beam Indicator . 55
...........................Reminder Tone . 62........Replacing Halogen Bulbs . 170
...................................Turning on . 62..............................Head Restraints . 75...............................Heated Mirrors . 81
.......................Heating and Cooling . 88
.............High Altitude, Starting at . 135............................High Beam Lever . 62
..............High-mount Brake Light . 174..Hood, Opening and Closing the . 124
..................................................Horn . 60...........................Hydraulic Clutch . 168
..........................Four-way Flashers . 64..............................Front Airbags . 9, 22
Front Seat......................................Adjusting . 73
.....................................Airbags . 9, 22.................................................Fuel . 122
....................................Economy . 127......................Fill Door and Cap . 123
...........................................Gauge . 58.....................Low Fuel Indicator . 56
................Octane Requirement . 122...............................Oxygenated . 122
........................Tank, Refueling . 123..............................Fuse Locations . 207
.....................Fuses, Checking the . 204
...............Gas Mileage, Improving . 127..........................................Gasohol . 122.........................................Gasoline . 122...........................................Gauge . 58
.....................Low Fuel Indicator . 56................Octane Requirement . 122
........................Tank, Refueling . 123................Gas Station Procedures . 123
Gauges...Engine Coolant Temperature . 59
...............................................Fuel . 58Gearshift Lever Positions
..........Automatic Transmission . 138..............Manual Transmission . 136
........................................Glove Box . 84Gross Axle Weight Rating
.....................................(GAWR) . 131Gross Vehicle Weight Rating
.....................................(GVWR) . 131...Identification Number, Vehicle . 212
..............If the Engine Overheats . 197
..............If the Engine Wont Start . 194Ignition
..............................................Keys . 66...........................................Switch . 68
............Timing Control System . 220........................Immobilizer System . 67
.........Important Safety Precautions . 6Indicators
..............ABS (Anti-Lock Brake) . 55Brake (Parking and Brake
....................................System) . 55................Charging System . 54, 200
.............................Cruise Control . 56DRL (Daytime Running
......................................Lights) . 55
Index
G
H
I
IV
CONTINUED
...................................High Beam . 55........Key (Immobilizer System) . 56
......................................Low Fuel . 56................Low Oil Pressure . 54, 200
....................Malfunction Lamp . 201...........................Side Airbag Off . 54
...............................................SRS . 54.................................Trunk Open . 56
Turn Signal and Hazard...................................Warning . 56
..............................Washer Level . 56Indicators, Instrument
.......................................Panel . 51, 52...............................Infant Restraint . 32
Infant Seats......................................Installing . 35
................Tether Anchor Points . 40...................Inflation, Proper Tire . 178..................High Speed Driving . 179
.........................Normal Driving . 179...................................Inside Mirror . 80
.............................Inspection, Tire . 180....................Installing a Child Seat . 35
........................Instrument Panel . 3, 50........Instrument Panel Brightness . 63
................Instrument and Controls . 49
.................................Interior Lights . 86........................................Introduction . i
.................Jacking up the Vehicle . 190.......................................Jack, Tire . 189
................................Jump Starting . 196
..................................................Keys . 66
.......................Label, Certification . 212.................Lane Change, Signaling . 62
..................Lap/Shoulder Belts . 14, 18Lights
....................Bulb Replacement . 170...............................Indicators . 51, 52
.........................................Parking . 62..................................Turn Signal . 62
....................................Load Limits . 131......LOCK (Ignition Key Position) . 68
Locks.......Anti-theft Steering Column . 68
............................Fuel Fill Door . 123.................................Power Door . 69
...........................................Trunk . 70........................Low Coolant Level . 126.........................Low Fuel Indicator . 56
...Low Oil Pressure Indicator . 54, 200................................Lower Anchors . 36
...Lower Gear, Downshifting to a . 136
...Lubricant Specifications Chart . 214...........Luggage, Storing (Cargo) . 130
..................................Maintenance . 149Owner’s Maintenance
...................................Checks . 152.................................Record . 155-157
......................Required Indicator . 57..........................................Safety . 150
.............................Schedule . 151-154.Malfunction Indicator Lamp . 54, 201
IndexIN
DE
X
J
K
L M
V
...................Manual Transmission . 136...............Checking Fluid Level . 167
.......................................Shifting . 136........Manual Transmission Fluid . 167
....................................Mats, Floor . 175...............................Meters, Gauges . 58
...................Methanol in Gasoline . 122..........................Mirrors, Adjusting . 80
...............Modifying Your Vehicle . 129.........................................Moonroof . 79
......................Closing Manually . 203.....................................Operation . 79
..................................................MP3 . 99
..........Neutral Gear Position . 140, 143
..................New Vehicle Break-in . 122.....................Normal Shift Speeds . 137
...................NOTICE, Explanation of . i...............Numbers, Identification . 212
...Octane Requirement, Gasoline . 122.........................................Odometer . 58
...............................Odometer, Trip . 58Oil
........................Change, How to . 160......................Change, When to . 153......................Checking Engine . 125..............Pressure Indicator . 54, 200
Selecting Proper Viscosity......................................Chart . 159
...........ON (Ignition Key Position) . 68Onboard Refueling Vapor
....................................Recovery . 219..............................Outside Mirrors . 80
....................Overheating, Engine . 197....Owner’s Maintenance Checks . 152
.........................Oxygenated Fuels . 122
...................Radiator Overheating . 197
..............Panel Brightness Control . 63...............Park Gear Position . 139, 143
...........................................Parking . 145.................................Parking Brake . 81
Parking Brake and Brake.................System Indicator . 55, 202
...............................Parking Lights . 172..Parking Over Things that Burn . 221
.............................PGM-FI System . 220..................................Playing a Disc . 99
...................................Pollen Filter . 176..........................Power Door Locks . 69
..........Power Socket Locations . 82, 85....................Power Steering Fluid . 169
..............................Power Windows . 78.........Pregnancy, Using Seat Belts . 16
........................Preparing to Drive . 134.........Protecting Adults and Teens . 11
...Additional Safety Precautions . 16.....Advice for Pregnant Women . 16
........................Protecting Children . 27.......................General Guideline . 27
................Installing a Child Seat . 35.......................Protecting Infants . 32
.......Protecting Larger Children . 41.........Protecting Small Children . 33
.................Selecting a Child Seat . 34Using Child Seats with
.....................................Tethers . 40.............................Using LATCH . 36
Index
N
O
P
R
VI
*
*
*
CONTINUED
Radio/CD/Cassette..............................Sound System . 92
...Recommended Tire Pressures . 179.................Radio Theft Protection . 114
...................Readiness Codes . 201, 222Rear Lights, Bulb
..............................Replacement . 173............................Rear Seat Access . 74..........................Rear Seat, Folding . 76
............................Rear View Mirror . 80.................Rear Window Defogger . 64................Reclining the Seat-backs . 73
.......Recommended Shift Speeds . 137........................................Refueling . 123
.................Reminder Indicators . 51, 52
.......................Remote Transmitter . 71Replacement Information
..............Dust and Pollen Filter . 176................Engine Oil and Filter . 160
..........................................Fuses . 204................................Light Bulbs . 170
....................................Schedule . 151................................Spark Plugs . 214................................Timing Belt . 169
......................Tires and Wheels . 181.............................Wiper Blades . 176
Replacing Seat Belts After a............................................Crash . 20
..........Reporting Safety Defects . 226Reserve Tank, Engine
...............................Coolant . 126, 162...............................Restraint, Child . 27
..........Reverse Gear Position . 139, 143......................................Roof Rack . 132
................................Rotation, Tire . 181
..................................Safety Belts . 8, 18.........Safety Defects, Reporting . 226
.................................Safety Features . 7...........................................Airbags . 9
.......................................Seat Belts . 8.............Safety Labels, Location of . 46
...............................Safety Messages . ii.....................................Seat Belts . 8, 18
...............Additional Information . 18Automatic Seat Belt
...............................Tensioners . 19.....................................Cleaning . 174
................Lap/Shoulder Belt . 14, 18................................Maintenance . 19
Reminder Indicator and................................Beeper . 18, 54
...................System Components . 18...............Use During Pregnancy . 16
Wearing a Lap/Shoulder.....................................Belt . 14, 18
.................................................Seats . 73.........................Seats, Folding Rear . 76
.....................Selecting a Child Seat . 34...............................Serial Number . 212
...........................Service Intervals . 153
...........................Service Manual . 227.........Service Station Procedures . 123
..........................Setting the Clock . 115...Shift Lever Position Indicators . 138
........................Shift Lock Release . 141................................Side Airbags . 9, 24
..........................Off Indicator . 26, 54Side Marker Lights, Bulb
..............................Replacement . 172...............................Signaling Turns . 62
..................................Snow Chains . 183.....................................Snow Tires . 182
..............Socket, Accessory Power . 85
IndexIN
DE
X
S
VII
*
..................................Sound System . 92Spare Tire
......................................Inflating . 188............................Specifications . 215
....................................Spark Plugs . 214................................Specifications . 214................................Speed Control . 117................Speed Limiter . 137, 140, 144
..........SRS, Additional Information . 21...Additional Safety Precautions . 26
.............................Airbag Service . 26......Airbag System Components . 21
How the Passenger Airbag...............Off Indicator Works . 26
..How the SRS Indicator Works . 25How Your Front Airbags
.........................................Work . 22...How Your Side Airbags Work . 24
.............................SRS Indicator . 25, 54....START (Ignition Key Position) . 68
.......................Starting the Engine . 135In Cold Weather at High
..................................Altitude . 135................With a Dead Battery . 196..............State Emissions Testing . 222
........Steam Coming from Engine . 197
Steering Wheel..................................Adjustment . 65
.............Anti-theft Column Lock . 68...............Steering Wheel Buttons . 117
.....................Stereo Sound System . 92....................Storing Your Vehicle . 185
Supplemental Restraint..................................System . 9, 21......................................Servicing . 26
.........................SRS Indicator . 25, 54...................System Components . 21
..................................Synthetic Oil . 160
..........Taillights, Changing Bulbs . 173.Taking Care of the Unexpected . 187
....................................Tape Player . 111Technical Descriptions
....DOT Tire Quality Grading . 216.....Emissions Control Systems . 219
.....................Oxygenated Fuels . 122Three Way Catalytic
.......................Converter . 220, 221.......................Temperature Gauge . 59.....................Tether Anchor Points . 40
................Theft Protection, Radio . 114Three Way Catalytic
...........................Converter . 220, 221..................Tilt the Steering Wheel . 65
..........................Time, Setting the . 115....................................Timing Belt . 169....................................Tire Chains . 183
.........Tire, How to Change a Flat . 189...............................................Tires . 178
..............................Air Pressure . 179.........................Checking Wear . 180..........................Compact Spare . 188
......DOT Tire Quality Grading . 216......................................Inflation . 178
..................................Inspection . 180.....................................Labeling . 218
..............................Maintenance . 181...................................Replacing . 181
......................................Rotating . 181...........................................Snow . 182
............................Specifications . 215...................Tools, Tire Changing . 189
Towing.....................................A Trailer . 148
................Emergency Wrecker . 209
Index
T
VIII
*
*
*
Unexpected, Taking Care..........................................of the . 187
..Uniform Tire Quality Grading . 216........................Unleaded Gasoline . 122
.......Used Oil, How to Dispose of . 161......................Using a Booster Seat . 42
..................................Vanity Mirror . 85.................Vehicle Capacity Load . 131
......................Vehicle Dimensions . 214....Vehicle Identification Number . 212
.............................Vehicle Storage . 185........................................Ventilation . 90
.................................................VIN . 212..................................Viscosity, Oil . 159
.............WARNING, Explanation of . ii................Warning Button, Hazard . 64
.........Warning Labels, Location of . 46....................Warranty Coverages . 225
Washer, Windshield........Checking the Fluid Level . 164
.......................................Indicator . 56.....................................Operation . 61
Wheels...............Adjusting the Steering . 65............Alignment and Balance . 181
..........................Compact Spare . 188...................................Replacing . 181
..............................Wrench, Nut . 190Windows
..................Operating the Power . 78...........................Rear, Defogger . 64
Windshield.......................................Cleaning . 61.....................................Defroster . 91
.......................................Washers . 61Wipers, Windshield
.......................Changing Blades . 176.....................................Operation . 61
....................................Worn Tires . 180.....Wrecker, Emergency Towing . 209
TransmissionChecking Fluid Level,
..............................Automatic . 165Checking Fluid Level,
...................................Manual . 167..................Fluid Selection . 166, 167
..............Identification Number . 213.............Shifting the Automatic . 138
..................Shifting the Manual . 136...................................Treadwear . 216
...................Treadwear Indicators . 180.......................................Trip Meter . 58
................................................Trunk . 70....................Emergency Opener . 70
........................................Opening . 70............................Open Indicator . 56
....................................Turn Signals . 62
: U.S. only
IndexIN
DE
X
U
V
W
IX
Service Information Summary
Gasoline:
Fuel Tank Capacity:
Recommended Engine Oil:
Automatic Transmission Fluid: Power Steering Fluid:
Brake Fluid:
Tire Pressure (measured cold):
Manual Transmission Fluid:
13.2 US gal (50 )
30 psi (210 kPa , 2.1 kgf/cm )
Unleaded gasoline, pump octanenumber of 86 or higher.
API Premium grade 5W-20detergent oil (see page ).
Oil change capacity (includingfilter):
Use Honda ATF-Z1 (AutomaticTransmission Fluid) only
Honda Power Steering Fluidpreferred, or another brand ofpower steering fluid as atemporary replacement. Do notuse ATF (see page ).
Honda Heavy Duty Brake FluidDOT 3 preferred, or a DOT 3 orDOT 4 brake fluid as a temporaryreplacement (see page ).
Front/Rear:
Spare Tire:60 psi (420 kPa , 4.2 kgf/cm )
Honda ATF-Z1 (AutomaticTransmission Fluid) preferred, ora DEXRON III ATF as atemporary replacement (see page
).
Honda Manual TransmissionFluid preferred, or an SAE 10W-30or 10W-40 motor oil as atemporary replacement (see page
).
Capacity (including differential):1.6 US qt (1.5 )
3.4 US qt (3.2 )
3.7 US qt (3.5 )
HX model (CVT) only:
159
166 169
168
167
U.S.: DX, Value Package, LX,LX Special Edition
Canada: DX, REVERB, LX
U.S.: HX, EX, EX Special EditionCanada: Si