Post on 27-Dec-2015
description
transcript
Simple Solutions are the Best!
1-877-888-8727 www.OneEyeIndustries.com
Since 2004
2012A
Worldwide Distribution
1) Why is magnetic filtration a value? Quality magnetic filters are capable of filtering to submicron levels without flow restriction and are reusable for 10+ years. The most damaging contaminant in engine lube, hydraulic fluid, fuel and coolant is ferrous metal under 10 microns.
2) How do you collect non ferrous contamination on a magnetic filter? Through static adhesion caused by static charge build up with the high flow fluids and or gases.
3) What types of magnetic filters are there? The most common are ceramic and have been used to filter oil and fluids for the past 50 years. The new magnetic filters use rare earth magnets in the magnetic filters.
4) What is the difference between ceramic and rare earth magnetic? Ceramics are low in magnetic strength and will crack and disassemble when exposed to vibration. They also lose their magnetic field strength when exposed to high heat. Exposed ceramic is also very hard to clean.
Rare earth magnets are 4 times stronger than ceramic magnets and handle high heat without losing field strength and are highly resistant to vibration. They are coated and do not crack. They are installed in stainless steel tubes and retain their strength and clean very easily. 5) What are the advantages of OEI magnetic filters? OEI magnetic filters are manufactured with our patented design and are 12 times stronger than ceramic magnet filters and are encased in stainless steel tubes in a patented format that creates powerful projected radial fields that have larger surface area than traditional magnetic filters rods. 6) How do you clean a magnetic filter rod? The OEI magnetic filter rod design has no magnetic field at the end thereby you slide the contamination down to the end and it falls off. 7) What do you do with contamination collected? It is recommended to have the trapped contamination analyzed for wear debris identification. The magnetic filter becomes a predictive maintenance tool.
8) Can I purchase your product directly? We have distribution in most locations around the world and if we do not cover your area, yes we will supply direct.
9) Custom designs? Yes we welcome custom designs.
10) What happens if you remove all the metal out of oil? Our magnetic filters remove the ferrous and in many applications the non ferrous contamination to submicron levels due to static adhesion but you will never remove all the metal as it is produced by moving metal parts, new oils and fluids are contaminated with metal and air ingression contaminates the system with fine metal particles under 10 microns. If you are tracking the contamination levels through oil analysis and install magnetic filters you will simply drop your bench mark levels much lower. The less hard metals results in less wear thereby extended component and fluid/oil life.
11) How long do magnetic filters last? OEI magnetic filters have a 10+ year life.
F.A.Q.
www.OneEyeIndustries.com
Magnetic Filter Cores A novel approach to proactive maintenanceBy Christian Bauer, Pall Corporation and Roger Simonson, One Eye Industries
The generation of ferrous contaminants in most hydraulic and lube sys-
tems due to both normal and abnormal wear is a fact of life. Knowing the
amount and type of wear particles in the fluid system is paramount to avoid-
ing unscheduled outages. Standard filter elements will capture any type of
particulate contamination, ferrous and non-ferrous, within their media matrix
according to their micron rating. Identification of the contamination captured
typically requires off-site laboratory analyses.
Built-in magnetic filter cores can capture ferrous contaminants in fluid systems,
down to < 1 µm, before they reach the actual filter, thus providing an excel-
lent diagnostic tool for contamination monitoring and proactive maintenance.
Due to static adhesion, the cores can also retain some of the non-ferrous
contaminants. By simply removing the magnetic core and examining the
contamination retained on it under a microscope, reliability and maintenance
engineers across many industries now have a valuable tool for identifying
potential wear-related issues before they become a real problem.
Pall CorporationPALL
Reusable Oil Filter Magnets
www.OneEyeIndustries.com
Mission Statement
To design and manufacture the most effective cost efficient filtration systems in the world and answer the challenges the industry presents.
To grow our company into an international supplier through strategic partnerships with quality companies who operate on a similar high level of integrity and commitment.
With a dedicated effort, increase the application of our filtration solutions to improve industry efficiency thereby reduce overall dependency on fossil fuels and a reduction of harmful emissions that result from our industrial revolution.
About Us
One Eye Industries Inc welcomes its 16th year in business. With 4 years of product development and entering our 12th year of sales, our product lines continue to grow to answer the demand and expanding customer base around the world in every industry.
We manufacture an extensive product line utilizing new magnet technology. Our filters work with and compliment existing filtration systems and or replace them with reusable stainless screen filters. Custom designs are welcome.
Industry has been reluctant to employ magnetic filtration due to years of exposure to ineffective design and limited magnetic ability. Recent technological advances in magnetic properties and manufacturing processes have resulted in smaller, stronger high tech magnets available that allow innovative new designs for filtration systems and dramatically improving traditional magnetic filtration.
Industry research states “Iron and Steel” particles under 10 microns in size are the most damaging contaminants in air compression, water, lubrication, hydraulic fluid, coolant and fuel systems. The rate at which contamination enters these systems is greatly underestimated and understated. Likewise, the effectiveness of traditional filters at removing metal contaminants is greatly overstated. Magnetic filtration has practical and beneficial applications for all industry: chemical processing, oil & gas refining, manufacturing, construction equipment, transportation, marine and pulp & paper.
Our first line: reusable magnetic filters that compliment and work with existing disposable filters. They attach to the outer skin, extract and trap contaminants to the interior filter skin.
Our second line: magnetic rods and scrubber filters install in-tank, or inline. They offer maximum filtration, no bypassing with minimal flow restriction, low & high- pressure applications with ten plus years of service.
Our third line: the ADD-Vantage 9000 series are heavy-duty reusable stainless screen filters equipped with an internal magnetic filter and an internal fail-safe by-pass. When the bypass is activated the fluid is still filtered by the magnetic filter. They are environmentally friendly with ten plus years of service.
All our products offer long life, are user friendly, easily cleaned, reusable and maintained with minimal effort and cost. Cleaner fuel and lubricants for all applications in industry will result in reduced maintenance costs and increased productivity. This will reduce the demand on industry to produce and use more energy that results in increased emissions.
R.M. Simonson
Founder, President & CEO
Table of Contents
1
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
1000 SeriesReusable Magnetic Filter Pads 3 sizes available for oil, fuel, transmission and hydraulic disposable spin-on filters
Page 2 - 3
www.OneEyeIndustries.com
One Eye Industries Inc. assures:• Consistent Quality (ISO 9000) • Leading Technical Innovation • Premier Customer Service
OEI manufactures environmentally friendly filtration systems with proprietary magnetic technology. Reusable long life filters that allow extended maintenance schedules, increased fluid and equipment component life.
From Consumer to IndustrialOEI provides solutions to retail consumers and to industrial users in the Oil & Gas, Marine, Manufacturing, Mining and associated industries to effectively filter and remove ferrous and nonferrous contamination in lube oil, hydraulic fluid, fuel, coolant, gear oil, glycol, process/effluent water and chemicals.
Product LinesMagnetic Filter Pads: Attaches to and compliments existing disposable filters for lube oil, fuel, hydraulics, and coolants applications. Magnetic Filter Rods & Scrubbers: Multiple designs for inline and reservoir applications with or without traditional filtration.ADD Vantage 9000 Series: Designed to replace disposable filters, combining two filtration technologies in one filter. Cleanable true absolute rated Stainless Steel elements and patented magnetic filter technology results in a highly effective environmentally friendly filter.
Why Filter Ferrous Contaminants?Removal of ferrous contaminants (iron, steel, etc) will dramatically reduce the damaging wear cycle, extending the life, the fluids and equipment.Studies show ferrous particles smaller than 10 microns will generate 3 to 5 times more wear than larger particles.Equipment is being manufactured with tighter tolerances causing a demand for higher filtration requirements to sub-micron levels. These contaminates are carried into high pressure contact areas causing damage to softer metals, seals, bearings and gaskets.The use of extremely strong magnetic fields, are required to trap these particles, especially in “high flow” and or high viscous fluids.OEI’s patented magnetic technology traps ferrous and nonferrous contaminants to sub-micron in size.In many cases this is the first time credible filtration has been achieved to this level.
2000 • 2500 • 3000 SeriesMagnetic Filter Rods For installation inside of elements, tanks and reservoirs for both static and mobile equipment
Page 4 - 6
7000 SeriesMagnetic Plugs
Replacement drain or level plug for final drives, rear ends, transfer cases and transmissions
Page 9
5000 SeriesMagnetic Filter ScrubberMagnetic Y-Strainer For inline installation allowing for easy cleaning and no flow restriction
Basket & Cone StrainersOil & Gas, Pipelines, Refineries.
Fuel Gas, Canister Filtration
Page 14 - 23
8000 SeriesCustomized Filtration SystemsKidney loop, High Flow FiltrationHydrostatic Lube Lift
Page 24 - 28
ADD-Vantage 9000
The most advanced filter technology for fluids in the world.
Enviro- Wash 9000
Page 29 - 38
4000 SeriesMagnetic Funnel Scrubber
Food and Industrial Grade in line filtration
Page 12 - 13
1000 Series Magnetic Filter Pads
2
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
2
BT500 For all brands of disposable filters up to 3” in diameter• Small trans missions, rear-end dis posable filters, small fuel filters• Marine engines and recreational vehicles
BT800 For all brands of disposable filters 3”- 4“ in diameter. Fuel, engine oil, hydraulic , coolant and transmission filters.
BT900 For all brands of disposable filters 4” and up in diameter. Fuel, engine oil, hydraulic, coolant and transmission filters
OIL FILTER MAGNET
Multiple high strength magnetic fields trap damaging
microscopic ferrous and non-ferrous metal contaminants
that the filter cannot
OIL FILTER MAGNET
Magnetically attaches to disposable filters
Works with and compliments existing disposable filters by:
• By filtering ferrous and non-ferrous contamination to sub- micron levels• Removal of the hard metals reduces wear on the softer components• Extends the lube oil, hydraulic and coolant fluids opera-tional life
MULTIPLEHIGH STRENGTH
MAGNETIC FIELDSTRAP DAMAGING
MICROSCOPIC METALCONTAMINANTSTHAT THE FILTER
CANNOT
OIL FILTER MAGNET
MAGNETICALLY ATTACHESTO DISPOSABLE FILTERS
OIL FILTER MAGNET
FM800OIL FILTER MAGNET
FM900OIL FILTER MAGNET
MAGNETIC FILTRATION SOLUTIONS
BT 900
2 3/8"60.3 MM
1/4" / 6.3 MM
2 3/8"60.3 MM
3"76.2 MM
6"152.4 MM
1/4" / 6.3 MM
3/8" / 6.3 MM
4"101.6 MM
6"152.4 MM
2 3/8"
1/4"
2 3/8"
3"
6"
1/4"
3/8"
4"
6"
MULTIPLEHIGH STRENGTH
MAGNETIC FIELDSTRAP DAMAGING
MICROSCOPIC METALCONTAMINANTSTHAT THE FILTER
CANNOT
OIL FILTER MAGNET
MAGNETICALLY ATTACHESTO DISPOSABLE FILTERS
OIL FILTER MAGNET
FM800OIL FILTER MAGNET
FM900OIL FILTER MAGNET
MAGNETIC FILTRATION SOLUTIONS
BT 900
2 3/8"60.3 MM
1/4" / 6.3 MM
2 3/8"60.3 MM
3"76.2 MM
6"152.4 MM
1/4" / 6.3 MM
3/8" / 6.3 MM
4"101.6 MM
6"152.4 MM
2 3/8"
1/4"
2 3/8"
3"
6"
1/4"
3/8"
4"
6"
1000 SERIES MAGNETIC FILTER PADS –
For application on all types and sizes of disposable filters.1MPBT500 Magnetic pad 2-3/8”W x 2-3/8”L x 1/4”T
1MPBT800 Magnetic pad 3” W x 6”L x 1/4”T
1MPBT900 Magnetic pad 4”W x 6”L x 3/8”T
ISO 9000 • Reusable • 1 Year Warranty on Pads • 10+ Year Life
Made in Canada
• No Tools Required
• Endure Temperature variance from -40 to 350 F
• Maintain integrity when contaminated with hydrocarbon fluids associated with all applible applications
60.3 mm
60.3 mm
6.3 mm
76.2 mm
152.4 mm
152.4 mm
6.3 mm
9.5 mm
101.6 mm
Reusable Oil Filter Magnets
3
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on PadsISO 9000 • Reusable • 3 Year Warranty • 10+ Year Lifewww.OneEyeIndustries.com
1000 Series Magnetic Filter Pads
Magnetic Patch
The Magnetic Patch is a temporary solution designed to plug off holes in piping, drop chutes and silos allowing production to be maintained. It is easily installed and removed during a scheduled down time. The Magnetic patch comes in two sizes and can be cut into smaller sizes to accommodate smaller holes and pipes. Custom sizes and designs are available for slurry product applications and high temperature applications up to 300F.
A quick & secure way of repairing holes in:
- Steel Pipe - Round Radius Elbows - Flat Back Elbows – Silos - Chutes
Model Number Dimensions 1MP813 - 8" x 13" x 3/8"
1MP1713 - 17" x 13" x 3/8"
N E W !
Yard-Master1YM32
The “Yard-Master” handles the toughest scrap metal problems and reducing costly tire damage & personal injury. Designed with OEI’s patented magnetic technology that allows the magnetic sweeper to float over the ground while keeping constant contact with the ground extracting debris such as nails, screws, staples, banding, iron chips under the ground surface that become exposed under the pressure of a tire.
The Yard-Master is constructed with high quality air filled 6” tires for ease of maneuvering, available in 3 lengths 12” for shop, 32” for shop or small yards and 42” and custom sizes for yard use. The magnetic sweeper is easily removed from the carrier for cleaning, simply place over a refuge receptacle and wipe clean with a heavy cloth or gloved hand.
2000 • 2500 • 3000 Series Magnetic Filter Rods
4
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Attach inside transmission and hydraulic cartridge elements.
ISO 9000 • Reusable • 3 Year Warranty on Rods • 10+ Year Life
2000/2500/3000 Series Magnetic Filter Rods are designed to be installed in reservoirs, gear boxes, filter elements, pipe lines and more. These Magnetic Filters will trap ferrous contaminants and non-ferrous contaminates (by static adhesion) to sub micron levels. Available in a variety of magnetic filter rod sizes and fasteners.
OEI manufactures all our Magnetic Filter Rods with 304/316 Stainless Steel Tubing (Monel and other Stainless grades are available). Rare Earth Magnets are installed in our patented method that creates the most powerful non-electric magnetic fields available. For filtration of Ferrous and Nonferrous (hydro statically charged) contamination down to sub-micron levels in all fluids, gases, chips and powders etc. Designed to be user friendly (easily cleaned) long life (10+ years) of service, custom designs are welcome.
Install inline before sock filters to eliminate worm holing.
Install in tank at the inlet/outlet
Magnetic Filter Protective Cage
National Course or Metric Thread
Magnetic Base Cam-lock with Male Adapter
NPT, ORB, BSP or Metric Plug
Protective Cage
Magnetic Filter
OEI's protective cage is designed to aid in the installation and removal of the magnetic filter.
The protective cage is supplied with all 3R2 magnetic filters as a safety precaution due to the magnetic filters strength.
Box 1 Box 2
25RPC 12
Box 1MagneticFilter Size
2RPC - 1/2" Dia.
25RPC - 3/4" Dia.
3RPC - 1" Dia.
3R2PC - 2" Dia.
Box 2Magnetic
Filter Length
In Inches
How To Order .....
5
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Reusable Oil Filter Magnets
ISO 9000 • Reusable • 3 Year Warranty on Rods • 10+ Year Life
2000 • 2500 • 3000 Series Magnetic Filter Rods
2000/2500/3000 Series Magnetic Filter Rods
Box 4 Fastener Size5/16” NC-Only3/8” NC-Only1/2”5/8”3/4”1”
1 1/4”1 1/2”
2”
10 mm Bolt Thread Only
12 mm Bolt Thread Only
14 mm
16 mm
18 mm20 mm
22 mm24 mm50 mm
Etc.
Blankfor MB, MBA, DS, CL or Tee
Box 1 Box 2 Box 3 Box 4 Box 5 Box 6 Box 7 Box 8
25R NC 38 7 T 3 HD
Box 1 Magnetic Filter Rod2R 1/2” Diameter 25R 3/4” Diameter 3R 1” Diameter
3R2 2” DiameterIncludes Protective Cage Box 6 Fastener Tool
Blank NC, MB, MBA, CL or DS
IS Internal SquareES External SquareIH Internal HexEH External HexT Tee EndD Disk
Box 2 TemperatureBlank 300F / 150CHH 600F / 300C
Box 3 FastenerNC Nation Course Thread
NPT Nation Pipe Thread
BSPP British Standard Pipe Parallel
BSPT British Standard Pipe Tapered
M Metric ThreadORB O-Ring BossMB Magnetic Base
MBA Magnetic Base AdjustableDS Dual StandCL Cam-LockT Tee
CU CustomAJ Adjustable
IT Internal Thread (Female)
Box 5 Magnetic Length
Insert in Inches 3, 3 1/2, 4, 7, 12, 16, 24, etc.
Box 7 T or D Length
Insert in Inches1, 112, 134, 2, 3, 312, etc.
Box 8 Design Strength
Blank Stationary Equipment
HD Mobile Equipment
FG Food Grade
HP High Pressure (over 300 PSI)
MODEL CODE:
HOW TO ORDER:
* Custom Designs are Available
3RT12D312 25RNC387T3HD
Reusable Oil Filter Magnets
6
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Parker "ModuFlow Series" Magnetic Filters
www.OneEyeIndustries.com
Pall Magnetic Filters
PALL Marksman Series
OEI has manufactured a magnetic filter specifically for the Parker "Moduflow Series" at the request of our customers. The magnetic filter is easily installed and removed for inspection and cleaning. As with all OEI magnetic filter this will enhance your fluid cleanliness and extend equipment life.
Original ModuFlow Series
OEI PART # - 2RMFD334
ModuFlow "Plus" Series
Single Element - 2RMFP7Double Element - 2RMFP17
Size OEI Part #1 Bag 3RT12PALLT18652 Bag 3RT24PALLT186540 inch 3RT40PALLT1865
PALL HF Series
Size OEI Part #20 inch 3RT20PALLHF40 inch 3RT40PALLHF60 inch 3RT60PALLHF
OEI has manufactured a magnetic filter specifically for the PALL "Marksman & HF Series" at the request of our customers. the magnetic filter is easily installed and removed for inspection and cleaning. As with all OEI magnetic filter this will enhance your fluid cleanliness and extend equipment life.
Foot Rest to protect the element Handle Clamp
N E W !
7
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Reusable Oil Filter MagnetsIndustrial Filtration Solutions
CAT Transmission Replacement Filter
25RCAT-7160 (with 3S-3439 Plate) 25RCAT-3251 (with 8P-3251 Plate)
The OEI magnetic filter is designed to replace the ceramic OEM magnetic filtration technology.
OEI’s powerful rare earth magnetic fields dramatically improve filtration of ferrous contamination to sub-micron levels. This allows easy cleaning and collection for analysis of the trapped contamination, extending fluid and transmission component life. Increases operational time and decreases maintenance costs.
Another advantage is to eliminate the opportunity for the OEM magnetic filter to contaminate the transmission fluid as a result of vibration and fracturing of the exposed ceramic magnets.
OEM CAT Magnetic Filter Old Ceramic Technology
25RCAT-1W1564
The 25RCAT-1W1564 magnetic filter is designed to be installed in the engine sump screen filter (1W-1564) enhancing its filtration capability to sub-micron levels with the use of OEI's patented magnetic technology.
The magnetic filter has been designed for easy installation, simply remove the bolt and washer #8-9, place the washer on the magnetic filter and use the magnetic filter to hold the sump screen in place. A Tee handle has been installed to assist with the installation.
www.OneEyeIndustries.com
Industrial Filtration Solutions
CAT Sump Filter Enhancement
CAT Motor Grader Chain Case Magnetic Filtration System
16H, G, M Motor Grader1PCAT-4D7678NPT
OEI now offers the Motor Grader Chain Case Magnetic Filter with the inspection plate ready for installation on the 16H, G, M, and 24H, G, M.
These plates can also be order seperately.
24H, G, M Motor Grader1PCAT-1206157NPT
Magnetic Filter and inspection plate for CAT Motor GraderModel Part Number16H, G, M - 3R20HD78PL24H, G, M - 3R24HD78PL
N E W !
Caterpillar Filter Enhancement
8
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Magnetic Filter / Level Monitor25RFC787
One Eye Industries is pleased to announce an innovative way to filter the contamination in the Komatsu 830E & GE 787 wheel motors. This magnetic filter design offers a multipurpose; first it acts as a level monitor for the oil, second as a filter to remove the most damaging contaminant “ferrous metal” to submicron levels. The third is a predictive maintenance tool, simply remove the trapped contamination and send it away to a lab for analysis.
The test will identify premature wear patterns of the components and allow predictive maintenance scheduling. The adjacent photo shows this magnetic filter is designed with our new 3/4” diameter magnetic filter projecting multiple 4” radial fields. A level line has been marked on the filter to aid in the maintenance of this unit. See our case study information on our web-site to see the results of applications around the world.
www.OneEyeIndustries.com
8
2RFCS787-2 or 2RFCS787-12(1/4" OR 5/16" Sample Tube) (1/2" Sample Tube)
4 in 1 Magnetic Filter/ Level Monitor/ Sampling Port
2RFCS787- #
One Eye Industries is pleased to announce an innovative way to filter and prevent ingression contamination in the Komatsu 830E & GE 787 wheel motors. This design is multipurpose; first it acts as a level monitor for the oil, second as a filter to remove the most damaging contaminant “ferrous metal” to submicron levels, third capable of extracting an oil sample without removing the filler cap reducing the opportunity for foreign materials to enter. The fourth is a predictive maintenance tool, simply remove the trapped contamination from the magnetic filter and send it away to a lab for analysis.
The test will identify premature wear patterns of the components and allow predictive maintenance scheduling. The adjacent photos shows the magnetic filter is designed with a 1/2” diameter projecting multiple 3” radial fields. A dip stick and a sampling port has been installed to aid in the preventative maintenance of this unit.
Dip Stick
Magnetic Filter
Sample Port
OEI has designed a reusable Stainless Steel Element (9ELSS77532x25) to replace Komatsu's 209-60-77531 disposable element. OEI's stainless steel elements provide maxi-mum filtration protection, eliminating any chance of “channelling or worm holing” the ele-ment is reusable and available in 40, 25 or 10 micron β200 rating.
The 2RNC3810T3 magnetic filter is designed to be installed in the Hydraulic Element Filter (209-60-77532) magnetic technology.
The magnetic filter has been designed for easy installation, simply remove the strainer and drill a 3/8" hole in the center bottom, attached the magnetic filter with (2) 3/8" washers place (1) washer on the magnetic filter insert through the strainer and fasten with the 2nd washer and 3/8" nut. The tee handle is designed to keep the magnetic filter centered in the element.
Komatsu Hydraulic Filter Enhancement
N E W !
Komatsu Wheel Motor Filtration
PC 1250 Enhanced Hydraulic Filtration
7000 Series Plugs
9
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Padswww.OneEyeIndustries.com
OEI manufactures plugs with High Energy Magnetics, designed to replace the OEM industries standard ceramic magnetic plugs for final drives, rear ends, transfer cases and transmissions.
* 300F Operating Temperature (600F optional)
Box 4Inches
NPT, BSP1/8”1/4”
3/8”1/2”3/4”1”
1 1/4”1 1/2”
2”2 1/2"
Box 1 Box 2 Box 3 Box 4 Box 5 Box 6
7P M 16 15 EH
Box 1 Magnetic Plug7P Plug
Box 2 TemperatureBlank 300F / 150CHH 600F / 300C
Box 3 FastenerNPT Nation Pipe Thread
BSPP British Standard Pipe Parallel
BSPT British Standard Pipe Tapered
M Metric ThreadORB O-Ring Boss
How to Order ...
* Custom Sizes and Designs are available
Plug Sizes & Types
Metric Sizes ORB Sizes
10mm -0412mm -05
14mm -0616mm -0818mm -1020mm -1222mm -1426mm -1627mm -2030mm -24
33mm -32
36mm etc.
Box 5 Metric Thread
1.01.251.52.0
Box 6 Fastener ToolIS Internal SquareES External SquareIH Internal HexEH External Hex
ESD External Square Drilled
Reusable Oil Filter Magnets
10
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Padswww.OneEyeIndustries.com
OEM Part #
Magnetic Filter Plugs & Magnetic Filter RodsOEI Part Number
Atlas Copco 5541 506500
ST 1520 Scoop Truck 7PM3320EH
Custom ST 8B - Scoop Truck Hydraulic Tank 3R24HDAC2ES CAT
1W-1564 Magnetic Filter for Engine Sump Filter (1W-1564) 3/4" x 6" w/ 3/8"nc and 2.875 x 3/8" Support tee25RCAT-1W1564
2A-3852 777 Final Drive/ Planetary, 16-H Grader Chain Case, 789 / 793 Front Wheel Cover, 621 B Final Drive 7PCAT-38372A-3852 Custom Design - 4"long x 1/2" diameter - Magnetic filter on a 2A-3852 25RCAT-38522H-3865 Magnetic Drain Plug Inside Square 7PCAT-2H3865
3E-2338For: 854G Rubber Dozer Engine, 5130B Excavator, 789 Cat Haul Truck Transmission, 793 Cat Haul Truck Trans-mission, 330 Excavator Final Drive, 621F Cat Scraper Final Drive Plug, 345 Excavator Final Drive, 375 Excavator 7PCAT-3E2338
3H-4190 793D Haul Truck Drive Pumps Drain Plug 7PCAT-3H41904B-2363 For: CAT 245 Excavator Sump Final Drive 7PCAT-23634D-7678 CAT 16H, G, M - Motor Grader Chain Case Inspection Plate 1PCAT-4D76784T-2069 D10 Pivot Shaft Fill & Drain Plug 7PCAT-20695K-7696 Wheel Loader Final Drive & Brake 988,992,836,B35C 7PCAT-76965P-8005 621F Scraper Transmission Housing Plug 7PCAT-80055P-8006 621F Scraper Transmission Housing Plug 7PCAT-80065P-4484 For: 854 R.T. Dozer Differential, 834 R.T. Dozer Differential, 988, 992 Differentials 7PCAT-44846B-5262 777 Final Drive/ Planetary, 16-H Grader Chain Case, 789 / 793 Front Wheel Cover, 621 B Final Drive 7PCAT-38376E-5047 For: 140H Grader Tandem Drive Plug -08 IH 7PCAT-50476E-7696 For: 140H Grader Tandem Drive Plug -08 IH 7PCAT-50476V-0439 For: 789 Cat Truck Final Drive, 854-G R.T Dozer Final Drive, 992 Wheel Loader 7PCAT-0439
6V-3298For: D-8 Transmission & Final Drive, D 9L, D-10 Transmission, D-IIR Final Drive, D-IIN Final Drive, 793 Rear Axle Drain, 797 Differential & Final Drive
3RCAT-8334
6V-3963 For: D6 Final Drive & Differential Drive, 793 Final Drive 3RCAT-39638B-6599 For: 637 Cat Scraper Transmission Plug 7PCAT-6599
8M-3837 777 Final Drive/ Planetary, 16-H Grader Chain Case, 789C / 793CD Front Wheel Cover, 621 B Final Drive 785C, 988H, G 7PCAT-3837
8M-5576For: 24-H Grader Differential, 789 Cat Truck Rear Axle Housing, 793 Cat Truck Rear Axle Housing777 Cat Truck Rear Axle Housing, 785 Cat Truck Rear Axle Housing
7PCAT-5576
8M-7160 Magnetic Filter For Transmission (3/4" x 9" w/ Plate (3S3439) ) 25RCAT-7160M-2782D For: Twin Disc Transmission - 345 Final Drive 7PCAT-2782D
9J-7031For: D-IIR Hydraulic Tank Drain and Engine, D-IIN Hydraulic Tank Drain and Engine, 621F Cat Scraper Final Drive, 24-H Hydraulic Grader, 854-G R.Tire Hydraulic Dozer
7PCAT-7031
9S-4181For: 854G Rubber Dozer Engine, 5130B Excavator, 789 Cat Haul Truck Transmission, 793 Cat Haul Truck Trans, 330 Excavator Final Drive, 621F Cat Scraper Final Drive Plug, 345 Excavator Final Drive, 375 Excavator,D10 7PCAT-4181
9S-4182 For: D-10R Hydraulics, D-10N Hydraulics, D10T 7PCAT-41829S-4183 For: 854G R.T. Dozer Engine, 5130B Excavator Engine 7PCAT-41839S-4185 D 10 Dozer Final Drive Drain Plug 7PCAT-41859S-4205 For 621E CAT Scraper 7PCAT-4205
9S-4208For: 854G Rubber Dozer Engine, 5130B Excavator, 789 Cat Haul Truck Transmission, 793 Cat Haul Truck Trans-mission, 330 Excavator Final Drive, 621F Cat Scraper Final Drive Plug, 345 Excavator Final Drive, 375 Excavator 7PCAT-4181
9S-8004 For: 24-H Motor Grader - Tandem Housing 7PCAT-80049S-8006 For. CAT 5110 Excavator Sump Final Drive 7PCAT-9S80069X-6451 For: C-15 CAT Engine Pan Plug 7PC15EEH
"Custom" = OEI's Designed Magnetic Filter
OEM / OEI Cross Reference List
Reusable Oil Filter Magnets
11
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
OEM / OEI Cross Reference List
www.OneEyeIndustries.com
OEM Part Number
Magnetic Filter Plugs & Magnetic Filter Rods OEI Part Number
CAT Continued
106-8187 D10 Transmission Drain Plug 7PCAT-8187
175-6689 For: 24-H Grader Differential, 789 Cat Truck Rear Axle Housing, 793 Cat Truck Rear Axle Housing777 Cat Truck Rear Axle Housing, 785 Cat Truck Rear Axle Housing 7PCAT-5576
Custom CAT 16-H, G, M Grader Chain Case Magnetic Filter "Includes stainless steel half coupler for 2" NPT Plug" 3R20HD78
Custom CAT 24-H, G, M Grader Chain Case Magnetic Filter "Includes stainless steel half coupler for 2" NPT Plug" 3R24HD78
Custom CAT 16-H, G, M Grader Chain Case Magnetic Filter "Includes modified inspection for Magnetic Filter" 3R20HD78PL
Custom CAT 24-H, G, M Grader Chain Case Magnetic Filter "Includes modified inspection for Magnetic Filter" 3R24HD78PL
Custom CAT D-8,D-9,D-10,D-11 Hydraulic Reservoir Magnetic Filter w/ Cam-Lock Mount 3RCL18HD
P & H
Custom P&H 2800 Shovel Crowd Case "Includes stainless steel half coupler for 2" NPT external hex head" 3R18HD78
Custom P&H 2300 Propel Gear Box Upper Location " Cam Lock Mount 24" Total Length, 20 " Magnetic Filter 3RCL24HDCU4
Custom P&H 2300 Propel Gear Box Lower Location " Cam Lock Mount 28" Total Length 12" Magnetic Filter 3RCL28HDCU16
KOMATSU
Custom KOMATSU 830E Hydraulic Tank Cap # TP 0623 with 24" Magnetic Filter 3RORB3224IH
Custom GE 787 Wheel Drive Filler Cap with (Sample Port / Dip Stick and Magnetic Filter.) (GE#41B538253P1) 2RFCS787
Custom GE 787 Wheel Drive Filler Cap with (1/4 or 5/16" Sample Port Dip Stick and Magnetic Filter.) 2RFCS787-2
Custom GE 787 Wheel Drive Filler Cap with (1/2" Sample Port Dip Stick and Magnetic Filter 2RFCS787-12
Custom GE 787 Wheel Drive Long Filler Cap with (1/2" Sample Port Dip Stick and Magnetic Filter.) 2RFCS787-127
Custom GE 787 Wheel Motor Filler Cap With Magnetic Filter 6" in Length (GE#41B538253P1) 25RFC787
07044-12412 830E Plug # 12412 7PM2415EH
07044-13620 Komatsu Plug # 31420, #13620 7PM3615EH
07044-31420 Komatsu Plug # 31420, #13620 7PM3615EH
H6881 830E Front Spindle Plug # H6881 7PNPT1IS
SF 9435 830E For: Haul Truck Wheel Drive Reservoir Plug 2RNPT1149ES
TY 8879 930E Front Spindle Plug # 7PNPT114IS
VJ 6489 830E Haul Truck Upper Wheel Drive Plug #VJ 6489 7PNPT114ES
VS 8411 VS 8411 Komatsu Wheel Drive Plug 42mm x 2.0 Magnetic Plug 7PM4220IH
209-60-77532 Hydraulic Element Filter For: PC1250 9ELSS77532x25
21N-60-12210 Hydraulic Spin on Filter For: PC1250 9ADV9-9377
LETOURNEAU
200-0002 Letourneau 200-0002 For: 1850 Final Drive 7PLET5262
LIEBHERR
409710601 Liebherr T282 Haul Truck Plug Part # 409710601 7PM3320EH
Liebherr 380 For: Ton Wheel Drive Haul Truck 7PORB16IH
Reclaimer Plug Long Travel Gear Box 42mm x 2.0 Magnetic Plug 7PM4220IH
SISU 98073 For: Final Drive (Western Star Haul Truck), 793/789 7PORBSISU72
SISU Differential (Western Star Haul Truck) 793/789 7PORBSISUH75
10336-F Front Wheel Brake Assem. Plug 2RLBR10336F
John Deere
R26727 John Deer R26727 For: G Series Back Hoe Axle Differential MT-2075, 310-G, 210-LE 2RORB5727
HITACHI
5500 Loader Final Drive 7PHITC114
Hyundai
Loader HL770-7 7PMM2215IS
Ford New Holland
9848947 Rear Differential Drain Plug 7PFD-8947
Sandvik
LH621 Wheel End Differential 7PSCK-9842
Custom Sizes and Designs are available
4000 Series Magnetic Funnel Scrubber
12
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
12
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
OEI Food Grade Magnetic Funnel Scrubbers are designed for maximum protection of sanitary lines and processing equipment from damaging ferrous contaminants. OEI’s patented Magnetic Technology traps particles to sub-micron levels.
• A variety of sanitary connec-tions are available for ease of installation and service.
• Employs powerful magnetic filter rods with full exposure to the product, with mini-mal flow restrictions and maximum contamination exposure.
• Magnetic filter rods are eas-ily removed for inspection and or cleaning.
• Magnetic field strength removes ferrous contamina-tion down to sub microns.
• Designed for permanent installations; simply flush clean then remove magnet-ic filter rods and wipe clean.
• Food • Dairy
• Beverage • Pharmaceutical
FG - Food Grade4FS42FGT
www.OneEyeIndustries.com
OEI Industrial Grade Magnetic Funnel Scrubbers are designed to remove unwanted ferrous metal (iron, steel, nickel and hardened stainless steel) from the processing lines in which products may be transferred and or packaged.
• A variety of connections are available for ease of installation and service.
• Employ powerful magnetic filter rods with full expo-sure to the product, with minimal flow restrictions and maximum contamina-tion exposure.
• Magnetic filter rods are easily removed for inspec-tion and or cleaning.
• Magnetic field strength removes ferrous con-tamination down to sub microns.
• Designed for permanent installations, just remove magnetic filter rods and wipe clean.
• Food • Plastic Pellets
• Mineral Powders • Glass Powder
IG - Industrial Grade 4FS43IGW
Box 1 Box 2 Box 3 Box 4 Box 5
4FS 4 42 2 FG T V
Box 1
Funnel Scrubber
Box 4 Installation Connection
T Tri-Clamps
W Weldlet
Box 2 Pipe Size
4112 - 1 1/2" (38mm) 44 - 4" (100mm)
42 - 2" (50mm ) 46 - 6" (150mm)
43 - 3" (75mm ) 48 - 8" (200mm)
Box 3 Usage
FG Processed Food
IG Preprocessed Food and Minerals
Box 5 Installation Mount
H Horizontal
V Verticle
4000 Series Magnetic Funnel Scrubbers
13
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
13
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Padswww.OneEyeIndustries.com
4150 SERIES MAGNETIC FUNNEL SCRUBBERS 4FS4150FG (Process Food Grade) 304/316 S/S 1-1/2" Inlet/Outlet 31-1/2" L x 4" D (Houses 3-3RF334 magnetic rods)3RF334 1" x 4-1/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4150FG)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4150IG (Industrial Grade) 304/316 S/S 1-1/2" Inlet/Outlet 19-1/2" L x 3" D (Houses 3-3RCL334 magnetic rods)3RCL334 1" x 3-3/4" S/S Rod w/1-1/2" Cam Lock Fastener (fits 4FS4150IG)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)
4200 SERIES MAGNETIC FUNNEL SCRUBBERS4FS4200FG (Process Food Grade) 304/316 S/S 2" Inlet/outlet 27-1/2" L x 4" D (Houses 3-3RF434 magnetic rods)3RF434 1" x 4-1/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4300/4200FG)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4200IG (Industrial Grade) 304/316 S/S 2" Inlet/Outlet 19-1/2" L x 4" D (Houses 3-3RCL434 magnetic rods)3RCL434 1" x 4-3/4" S/S Rod w/1-1/2" Cam Lock Fastener (fits 4FS4300/4200IG)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)
4300 SERIES MAGNETIC FUNNEL SCRUBBERS4FS4300 (Process Food Grade) 304/316 S/S 3" Inlet/Outlet 19" L x 4" D (Houses 3-3RF434 magnetic rods)3RF434 1" x 4-1/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4300/4200FG)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4300IG (Industrial Grade) 304/316 S/S 3" Inlet/Outlet 19-1/2" L x 4" D (Houses 3-3RCL434 magnetic rods)3RCL434 1" x 4-3/4" S/S Rod w/1-1/2" Cam Lock Fastener (fits 4FS4300/4200IG)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)
4400 SERIES MAGNETIC FUNNEL SCRUBBERS4FS4400FG (Process Food Grade) 304/316 S/S 4" Inlet/Outlet 23-1/2" L x 6" D (Houses 3-3RF634 magnetic rods)3RF634 1" x 6-3/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4400FG Funnel Scrubber)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4400IG (Industrial grade) 304/316 S/S 4" Inlet/Outlet 23-1/2" L x 6" D (Houses 3-3RCL634 magnetic rods)3RCL634 1" x 6-3/4" S/S Rod w/1-1/2" Cam Lock Fastener (fits 4FS4400IG)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)
FS4600FG SERIES MAGNETIC FUNNEL SCRUBBERS4FS4600FG (Process Food Grade) 304/316 S/S 6" Inlet/Outlet 36" L x 8" D (Houses 4-3RF834 magnetic rods)3RF834 1" x 8-3/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4600FG Funnel Scrubber)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4600IG (Industrial Grade) 304/316 S/S 6" Inlet/Outlet 36" L x 8" D (Houses 4-3RCL834 magnetic rods)4R3CL834 1" x 8-3/4" S/S Rod w/2" Ferrules Fastener (fits 4FS4600IG Funnel Scrubber)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)
4800 SERIES MAGNETIC FUNNEL SCRUBBERS4FS4800FG (Process Food Grade) 304/316 S/S 8" Inlet/Outlet 36" L x 10" D (Houses 4-3RF1034 magnetic rods)3RF1034 1" x 10-3/4" S/S Rod w/2" Ferrule Fastener (fits 4FS4800FG Funnel Scrubber)4FSHDSPC2 HD Single Pin Clamp (fastens magnetic rod to scrubber)4FSBG2 Buna Gasket Ring (seals magnetic rod to scrubber)4FS4800IG (Industrial Grade) 304/316 S/S 8" Inlet/Outlet 36" L x 10" D (Houses 4-3RCL1034 magnetic rods)3RCL1034 1" x 10-3/4" S/S Rod w/1-1/2" Cam Lock Fastener (fits 4FS4800IG Funnel Scrubber)4FSCLBG15 Buna Gasket Ring (seals magnetic rod to scrubber)
5000 Series Magnetic Filter Scrubber
14
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Padswww.OneEyeIndustries.com
Scrubber
Inlet/Outlet standard size is 1 1/2" NPT. Other sizes are available upon request, 1/4" to 1 1/2". * When installing
remember to allow clearance for rod removal.
5SC34 Series Scrubbers are designed for inline installation on low flow, light viscosity fluids such as fuel, engine lube, hydraulics and coolant systems, allowing for full exposure to the contamination and easy removal for cleaning. No flow restriction.
Magnetic filter: 3/4” D x 9” LDimension: 3” x 3” x 13” HSquare Housing 150psi
5SC34 Series Provides:
• Total Filtration
• 304/316 Stainless
• Mounts horizontal or vertical
• No flow restriction
• Plumbed with W.O.G. valves (optional)
• Monel Construction (optional)
• 300 F Operating Temperature
5000 Series Magnetic Filter Scrubber
* Inlet/Outlet standard size is 2 1/2“ NPTOther sizes are available upon request,
3/4" to 2 1/2”. * When installing remember to allow for rod removal clearance
5000 Series Provides:
• Total Filtration
• 304/316 Stainless
• Mounts horizontal or vertical
• No flow restriction
• Plumbed with W.O.G. values (optional)
• Monel Construction (optional)
• 300 F or 600 F Operating Temperature
5000 Series Scrubbers are installed prior to pumps, or on return lines for fuel, lube oil, hydraulics, coolants and water systems, allowing full exposure of the contaminants to the magnetic fields. They are easily cleaned and there is no flow restriction
5SC Dimension lbs/Kg12” 4”x4”x16”H 16304 mm 101x101x406 mm 7.224” 4”x4”x28”H 28608 mm 101x101x711 mm 12.736” 4”x4”x40”H 38914 mm 101x101x1016 mm 19.3
5SC2 Dimension lbs/Kg24" 6”x6”x30”H 57608 mm 150x150x762 mm 25.9
5SC Custom Outlet
Outlet can be located in several pos-ition standard design is 180 degrees off the inlet
Square Housing 150 psi
5SC ## RORBWLD ##
This unit is designed with offset in/outlet, a (R) round housing, the Magnetic Filter fastener is (ORB) Plug and the In/Outlet is (WLD) Weldlet
Round Housing 500 psi
5SCP12SCLNPT2This unit is designed with a (P) paral-lel in/outlet for easier installation. The ports can also be located near
the top.(5SCPT12SCLNPT2)
Square Housing150 psi
Standard Offset DesignSquare Housing 150 psi
Offset Ports
0 degrees
Offset Ports
Bottom
5SC012SCLNPT##5SCBTM12SCLNPT##
5000 Series Magnetic Filter Scrubber
15
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Padswww.OneEyeIndustries.com
5SCWOC9FLN8Designed for high volume low pressure
fluid filtration
5SCP ## SCLFLN ##This unit is designed for ease of installation, 5SC- (P) Parallel In/Outlet Design with (S) Square Housing, the magnetic filter fastener is (CL) cam-lock and the In/Outlet is (FLN) flange.
5SCPT ## SCLFLN ##This unit is designed for ease of installation, 5SC- (P) Parallel In/Outlet (T) ports are located near the top, (S) Square Housing, (CL) cam-lock fastener for the Magnetic Filter and the In/Outlet is (FLN) flange.
5SCD ## SCLFLN ##This unit is designed for larger piping applications, designed with offset in/outlet, 5SC- (D) Double magnetic filter with (S) Square Housing, the magnetic filter fastener is (CL) cam-lock and the In/Outlet is (FLN) flange.
Model #Body Dimension only
W x D x H
5SC349SCL 3 x 3 x 13
5SC 4 x 4 x H
5SCR 4 “ Diameter x H
5SCD 4 x 6 x H
5SCP 6 x 4 x H
5SCPR 6” Diameter x H
5SCPD 6 x 6 x H
5SCPDI 4 x 8 x H
5SC2 6 x 6 x H
5SC2P 8 x 6 x H
5SC2PR 8” Diameter x H
5SC2PD 8 x 12 x H
Note: H = Magnetic filter length plus 4 inches
Note: Removal clearance is equal to the filter height
5SCDPI ## SCLNPT ##This unit is designed for ease of installation, 5SC- (D) Dual Magnetic Filters, (P) Parallel In/Outlet, (I) Inline, (S) Square Housing, (CL) Cam-lock magnetic filter fasteners, (NPT) In/Outlet Ports. Designed for single pass applications such as fuel, chemical, water, etc.
N E W !
5000 SERIES SCRUBBER
16
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
16
www.OneEyeIndustries.com
Box 5: Length of Magnetic Filter Rod
9 9 inch Magnetic Filter Rod 5SC34 Scrubber only
12 12 inch Magnetic Filter Rod
24 24 inch Magnetic Filter Rod
36 36 inch Magnetic Filter Rod
Box 7: Fastener for Magnetic Filter
CL Cam-Lock 150 psi rating
ORB ORB 500 psi rating
Box 2: Magnetic Filter
34 3/4” Diameter Magnetic Filter 3 x 3 x 13H Body size
Blank 1” Diameter 300 F/ 150C
HH High Heat 1” Diameter 600F/300C
2 2” Diameter 300F/ 150C
2HH High Heat 2” Diameter 600F/300C
Box 3: In/Outlet Location
Blank Offset ports180 Degree off top port
0 Offset ports0 Degree off top port
90Offset ports90 Degree off top port (looking down from top)
270Offset ports270 Degree off top port (looking down from top)
P Parallel Ports Bottom
PT Parallel Ports Top
BTM Bottom Port
Box 6: Housing Design
S Square 150 psi rating
R Round (500 psi w/ ORB Fastener)
Box 9:
Port Size
1/2
3/4
1
1 1/2
2
2 1/2
etc.
Box 10:
Flange ANSI Class
150
300
600
900
1500
Box 1 : Scrubber Model
5SC 5000 Series Large Flow Systems
Box 4: # of Magnetic Filters
Blank Single Magnetic Filter
D Dual Magnetic Filter
DI Dual Inline Magnetic Filter
T Triple Magnetic Filter
Q Quadruple Magnetic Filter
Box 8: Port Options
NPT Nation Pipe Thread Tapered
FLN Flange
WLD Weldlet
BSP British Pipe
M Metric
HOW TO ORDER: Select the desired code (in the correct position) to construct a product.
EXAMPLE:
Box 1: Box 2: Box 3: Box 4: Box 5: Box 6: Box 7: Box 8: Box 9: Box 10:
5SC P D 24 S CL FLN 6 150
See inside back cover for Flow Rates Chart
17
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Reusable Oil Filter Magnets
www.OneEyeIndustries.com
Magnetic Canister Filtration System
OEI's dual filtration system has reinforced cleanable stainless steel cloth media elements combined with our patented magnetic filtration capable of filtering to sub-micron levels.
Designed to replace traditional bag and sock filtration systems.
Designed for filtering water, oil, coolant, cutting oil, fuel and cleaning solutions.
* Custom Replacement elements with magnetic filters for existing bag filters and cartridge filters are available
Features:
• Housing – Carbon or Stainless Steel construction, permanently piped in (up to 6” pipe size)• Elements 304 and 316 stainless steel, include magnetic filter rod• Extend cleaning life up to 3x, easy to clean• Reduce maintenance cost, PM• Eliminates bags, outer baskets, bag hold down assemblies, and bag restrainers• 150 psi (standard)• Carry all sizes – custom sizes are available• Flow rates up to 400 gpm – custom design for other flow rates• High heat applications are available• Long life 10+ years
Box 1 Box 2 Box 3 Box 4 Box 5 Box 6 Box 7
5CF 304 2 FLN BTM 25 V
Box 3
Pipe Size
2
34
6
Custom
Box 7
Seal
B - BunanE - Ethylene Propylene
V - Viton
TEV - Teflon Encapslated Viton
TSW - Teflon (solid white)
Box 1
Model Number- Filter Length
5CF-20
5CF-30
Box 4
In/OutletType
FLN - Flange
NPT - Thread
Box 5
In/OutletLocation
Blank - 180 degree
0 - 0 degree90 - 90 degree
270 - 270 degree
BTM - Bottom
Box 6
Micron Rating
10
2540
60
80
100
Box 2
Housing
304
316
CS- Carbon Steel
5000 Series Magnetic Canister Filtration System
Dimensions
5CF-20 5CF-30
A = 6" 6" B = 4" 4" C = 5.5" 5.5" D = 8" 8" E = 33" 52" F = 38" 57" G = 20" 20"
Y-Strainer • Bronze / Brass
18
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Y-Strainer • Bronze
www.OneEyeIndustries.com
OEI introduces our Magnetic Filter Y-Strainer Series
OEI understands the importance of filtration and the restrictions of space on equipment. OEI saw the need to improve the filtering capabilities of the traditional Y-Strainer by installing our patented Magnetic Filter. The Y-Strainer is now capable of trapping ferrous and non-ferrous contaminants by static adhesion to the sub-micron range. This is a major improvement to many systems that rely on a Y-Strainer for protection. Visit our web site for more information, and view our case studies.
• Chemical • Pneumatic Systems • Steering Systems • Grease Filtration
• Brake Systems • Coolant Systems • Fuel Systems • Hydraulic Systems
• Mobile & Static Equipment • Cryogenics Applications
WORKING PRESSURE (NON-SHOCK): 300 PSI @ 350F
Steam Rated 400 PSI @ 150F WOG
SizeIn. mm
1 25mm1 1/2 40mm2 50mm2 1/2 64mm3 75mm4 100mm
A
4 3/4 (12cm)5 3/4 (14.6cm)6 3/4 (17.1cm)8 (20cm)9 1/2 (23.5cm)12 (30.5cm)
B
4 (10cm)5 (12.7cm)6 (15.2cm)6 (15.2cm)7 (17.5cm)10 (25.4cm)
NETWEIGHT
Lbs Kg
3 1.45 2.37 3.212 5.516 7.322 10
DIMENSIONS
Box 1: Box 2: Box 3: Box 4: Box 5: Box 6:
5Y B 112 T A
Box 3
Pipe Size
1
1 1/22
2 1/2
3 4
Box 5Flange ANSI
Class Bronze leave
Blank
1 - 150
3 - 300
6 - 600
9 - 900
15 - 1500
Box 1
5Y- Magnetic Y-Strainer
Box 4
Port Type
T - Threaded
F - FlangeBox 2
B - BronzeS - Stainless Steel
BC- Cryogenics
Box 6
Mesh
X - No Mesh Screen
A - 20
B - 30
C - 40
D - 60
E - 100
NOTE:
BC- Y-strainer available in 2", 2 1/2", 3"
N E W !OEI is pleased to offer our custom designedMagnetic Filter Y-Strainer for cryogenic applications. Our flanged access allows access for cleaning at -320 degrees F. The magnetic filter removes both ferrous and non-ferrous contamination to submicron levels extending the life of linings and pump components.
Available in 2", 2 1/2" and 3" NPT port sizes
Y-Strainer • Stainless Steel
19
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
19
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Padswww.OneEyeIndustries.com
OEI’s Stainless Steel Magnetic Filter Y-Strainer Series
TempF
-20 to 100200300400500
150#Size A B WT
1” 6 3/8 5 111 1/2 7 3/4 5 1/4 172” 7 7/8 6 233” 10 7 1/2 424” 12 1/8 11 73
Working Pressure
275240215195170
150#, 300#, 600# ANSI 316SS - Raised Face Flange
5YS112F3
150# 300# 600#
Working Pressure
720620560515480
300#Size A B WT
2” 8 5/8 6 1/4 283” 12 8 1/4 564” 14 1/2 11 98
600#Size A B WT 1” 8 3/8 5 161 1/2 9 7/8 6 242” 11 1/8 6 3/4 473” 13 3/8 9 1/2 89
Working Pressure
1440124011201030955
• Body has machine seat to hold screen securely.
• Cover has a machined screen holder to align screen during installation and to retain sediment when cap is removed.
• Body is machined to hold gasket in a blow-out proof design.
• Flanges are back faced or spot faced.
TempF
-20 to 100200300400500
Size A B WT
2” 13 3/4 8 5/8 96
Working Pressure
360030952795256023905YS2F15
Description Material
Body ASTM A- 351 GR CF8MCap ASTM A- 351 GR CF8MGasket Spiral Wound SSScreen 304 SS Specify Mesh
1500# ANSI 316 SS - Raised Face / RJT Flange
5YS2T6
• Body has machine seat to hold screen securely.
• Cap has a machined screen holder to align screen during installation and to retain sediment when cap is removed.
• Body is machined to hold gasket in a blow-out proof design
TempF
-20 to 100200300400500
600#Size A B WT
1” 4 9/16 3 1/2 51 1/2 6 1/4 5 102” 7 1/2 6 1/2 162 1/2 8 3/8 7 213 9 1/2 8 1/2 26
WorkingPressure
1440124011201030965
600# 1500#
Working Pressure
36003095279525602390
1500#Size A B WT
1” 5 1/2 4 3/4 8
1 1/2 7 1/8 6 16
2” 8 5/16 6 5/8 22
600# / 1500# ANSI - 316SS - NPT Thread
Reusable Oil Filter Magnets
20
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Padswww.OneEyeIndustries.com
OEI Fuel Gas filtration system thats incorporates a magnetic separator as the primary filter and a pleated stainless steel cloth element as the final filter.
This environmentally friendly design will filter black powder contamination to submicron levels at an estimated 95+ efficency. This will significantly improve the burn and reduce the acid wear of the pistons and spark plugs.
The magnetic separators have a 5+ years operational life and the cleanable stainless steel cloth filter elements have a 3 to 5+ years operational life.
Our design allows the gas to have first contact with our magnetic separators stationed inside the stainless steel cloth elements thereby allowing an extended element operational life.
The magnetic separators have the most powerful non-electric magnetic fields in the industry with a holding strength of 300 Kg per 300 mm of length.
This magnetic field strength creates the ability to extract and trap submicron contamination while in high flow applications. The change out and cleaning intervals are policed by a differen-tial pressure gauge.
5000 Series Magnetic Fuel Gas Filtration System
Box 1 Box 2 Box 3 Box 4 Box 5 Box 6 Box 7
5DFG 304 4 FLN 600 C1200 10
Box 3
Port Size Inches
1
234 6
Etc.
Box 1
Model
5DFG
Box 4
In/OutletType
NPT - Thread
WLD - Weldlet
FLN - Flange
Box 7Micron Rating
102540Box 2
Housing
304
316
Custom
Box 5
NPT - Blank
WLD Blank
Flange Class
150300600900
1500
Box 6
Flow Rate
G ### -GPM
C ### - CFM
N E W !
Inlet 4.00"
40.0
0"
12.00"
5000 Series Magnetic Separator Cone Strainer Pipe Line Corrosion Erosion Management
21
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
NO# - Standard
I - Cloth
R - Reinforced
Wire meshon outsidesupported
Wire meshon insidesupported
Wire meshon outsidesupportedinside
––– Flow
––– Flow
––– Flow
Note: Standard perforation is .125Other perforations are available
Custom sizes and designs available* Quote per order
Two Stage Magnetic Separator Cone Strainer Designed for start-ups of new and existing pipelines. Traditionally after start-up the cone strainer is removed. The compressor and or pumps (meter) are left without protection from the ferrous metal created by the erosion and corrosion of the pipeline. With OEI’s Magnetic Filtration Cone Strainer the screen can be removed and the Magnetic Filter reinstalled to offer continuous protection.
Complete Assembly Removable Cone Mesh Flange with Magnetic Filter ip
• Mesh screen is removed and magnetic filtration continues with minimal flow restriction
• Protects compressors, pumps and flow meters
• Traps Black Powder - ferrous and non-ferrous contamination (due to adhesion)
• Designed with OEI patented magnetic technology
• Can be ordered with or without mesh screen cone
• 2” D x 12” L magnetic filter has holding capability of 600 lbs
www.OneEyeIndustries.com
Mesh Placement
• Refineries • Oil & Gas Transmission Lines • Chemical plants
Box 1: Box 2: Box 3: Box 4: Box 5: Box 6: Box 7
5SSC 12 300 40 Y 80
Box 2
Pipe Size
06
0810
12
14
16
182024
etc.
Box 3Flange ANSI
Class 150
300
600
900
1500
Box 1
Stainless SteelCone Strainer
Box 6Open Area
Y - 200%
Box 4
Mesh
NM - No Mesh Screen
20
30
40
60
100
Box 7Pipe
Schedule 40
80160
XXS
Box 5
5000 Series Magnetic Separator Basket Strainer Pipe Line Corrosion Erosion Management
22
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
22
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
All Stainless Steel (Fabricated)Oil & Gas • Pipeline • Refineries
• All certification and testing are available to International Standards• Custom built to allow maximum Magnetic Separator employment
www.OneEyeIndustries.com
5BT90
5BTS-T Strainer
5BTSQ-T Strainer Quick Opening
5BS-Basket Strainer
T StrainerDrawing
5000 Series Magnetic Separator Basket Strainer Pipe Line Corrosion Erosion Management
23
www.OneEyeIndustries.com
23
Box 1 Box 2 Box 3 Box 4 Box 5 Box 6 Box 7
5BS 316L 06 600 20 40 H
Box 1 Strainer Model
5BS Basket Strainer
5BSQBasket Strainer Quick Opening
5BTS T Basket Strainer
5BTQT Basket Strainer Quick Opening
5BT90 T 90 Basket Strainer
5BT90QT 90 Basket Strainer Quick Opening
Box 4 Flange150 900
300 1500
600 Pipe Size
Body Size Diameter
3 84 106 168 18
10 2412 26
Box 5 Mesh
20 80
40 100
60 ETC
Box 7 ProductC ChemicalsH Hydro Carbon FluidsN Natural GasW WaterL LNG
Box 6 Pipe Schedule
40 160
80 XXS
Box 3 Pipe Size / Inches
3 12 244 14 306 16 36
8 18 48
10 20 Etc.
HOW TO ORDER…..
OEI Basket Strainer Body Sizing
Box 2 Stainless Grade304 304L
316 316L
309 310
Custom Material
Please note: OEI magnetic separator basket strainers are designed with oversized housings to allow maximum employment of the magnetic separator to ensure the highest efficientcy. Industry standard of pipe to body ratio is a 2.5 to 1 ratio and OEI’s ratio is a minimum 4:1.
A chart specifying body sizing is shown below.
24
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Reusable Oil Filter Magnets
The prime function of the OEI Regrind Mill Hydrostatic Lift Lube System (HLS) is to lubricate the bearing during the three critical periods encountered during start-up and shut-down of the mill. The HLS should be operated during normal mill operation to maintain oil cleanliness and compliment the existing internal lubrication system for the bearing. One HLS system is required for each bearing.
Start-up is the critical period because of the frictional wear and stress developed prior to the formation of an adequate hydrodynamic oil film on the bearing surfaces.
The HLS is designed to float the mill on a film of oil which is introduced under high pressure (3000psi) at the center of the load area of the bearing. A satisfactory oil film is thereby established prior to start-up and during the critical period following start-up. The HLS will maintain an ample lubricant film throughout the critical periods of operation such as an unbalanced load (rock) and thermal expansion and the cooling off period.
The HLS is equipped with state of the art environmentally friendly filtration to ensure protection from premature wear of the entire system by maintaining a high level of oil cleanliness. The oil is filtered by a patented magnetic filter installed prior to the pump to protect the pump and again by the ADD-Vantage 9000 after the pump allowing filtration to submicron levels. The HLS is housed in a cabinet enclosure for protection from the harsh environment of the plant with quick connections for easy install and replace-ment for maintenance. Pressure gauges are visible at all times and remote monitoring optional.
* Custom Orders are available
Regrind Mill Hydrostatic Lift Lube System
www.OneEyeIndustries.com
8000 Series Hydrostatic Lift
8HLS-LP-HP
25
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Reusable Oil Filter Magnets
www.OneEyeIndustries.com
8000 Series Thermal Filtration System
N E W !DUAL PURPOSE THERMAL KIDNEY LOOP
Combining OEI submicron filtration capability and a thermal cooling system offers the ability to maintain a safe operational temperature and an ISO cleanliness level that will extend the lube oil and component life.
For application on gear boxes, hydraulic and coolant systems. Equipped with temperature gauges and sample ports before entering the unit and after to identify the reduction in temperature and contamina-tion in the fluid or oil.
Compact and available in custom designs for all applications to suit individual requirements. For mobile and static employment and powered by DC, AC and Hydraulic drive.
Our Thermal Kidney Loop system is designed with a magnetic filter in our Scrubber format prior to the pump to remove the ferrous metals to submicron levels and protect the pump and the thermal compo-nents and an ADD-Vantage 9000 filter to remove any residual non ferrous contamination before returning the fluid and or oil to the application.
To ensure the most efficient and effective Thermal Kidney Loop for your application please identify the following:
• Static or Mobile Oil Temperature Abient Air Temperature• Power Source AC/ DC Viscocity Required Heat Rejection (KW)• Voltage / Phase Reservoir Size ( gallons) Air Flow (Suction or Push)
Reusable Oil Filter Magnets
26
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
THE NEXT GENERATION KIDNEY LOOP FILTRATION SYSTEMS
ENVIRONMENTALLY FRIENDLY AND HIGHLY EFFICIENT
www.OneEyeIndustries.com
The OEI Kidney Loop combines two filtration technologies in a three filtering stage design that offers a highly efficient and environmentally friendly cleanable long life filtration system.
1st Filtering Stage and primary filter is a magnetic scrubber utilizing OEI patented technology rated to sub-micron filtration capability.
2nd and 3rd Filtering Stage is the ADD-Vantage 9000 series dual filter. The 2nd Filtering Stage is a cleanable long life stainless steel cloth media element that has an absolute rating of 25 or 40 microns and a nominal rat-ing of 8 to 10 microns. The stainless steel cloth media element eliminates the worm holing and channeling that occurs in cloth, paper, fiberglass, or polymer media. The 3rd and final Filtering Stage is a magnetic filter inside the Add-Vantage 9000 stainless steel element to trap contamination to sub-micron levels.
System Features
• Positive Displacement Gear Pump• 5 - 10 gpm• Viscosity 500 or 1000 cSt• OEI 5000 Series Magnetic Scrubber• Removable Oil Spill / Drip Tray• On/Off Switch• Electrical System – International Requirements • 16”W x 20”D x 30”H
Options• Disposable Elements• Water Absorbant Filter• OEI Series Scrubber 24” Height• ADD-Vantage 9000 Dual Filter 12” or 24” (reusable filter element and magnetic filter)• Differential Pressure Gauge• Pneumatic Pump• Sample Port• Mobile (Wheels)• Fluid Flow Gauge • Flow Switch• Particle Counter• Isolation Ball Valve• Customer Preferred Pump or Motor (brand)• Quick Connection Fittings
* Custom orders are available.8KLF-51-91-40-500-E-230-60-1-NPT-2
Gear Boxes - Hydraulics - Lube Oil Water - Chemicals - Glycol - Transformer Fluids
8000 Series Kidney Loop System
27
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Padswww.OneEyeIndustries.com
Box 1 Box 2 Box 3 Box 4 Box 5 Box 6 Box 7 Box 8 Box 9 Box 10
8KLF 51 91 25 1000 E 240-50-3 NPT 2
Box 3 ADD-Vantage 9000
Blank No Filter Mount
91 12" Tall Filter92 24" Tall Filter
Box 7 Voltage - Hertz - Phase
List
Box 1 Model Number
8KLF Kindey Filtration Stationary
8KLM Kidney Filtration Mobile
Box 4 Filter Micron Rating
Blank No Filter
x 100 100 Micron B200
x40 40 Micron B200
x25 25 Micron B200
x1 1 Micron B200
WA Water Absorbent Filter
DP Disposable Element
Box 5 Oil Viscosity
500 up to 500 cSt
1000 500 to 1000 cSt
Box 6 Pump
E Electric
P Pneumatic
Box 2 Scrubber Model
51 12" Tall Scrubber
52 24" Tall scrubber
Box 8 Pluming Connection
NPT National Pipe Thread
BSP British Standard Pipe
Q Quick Coupler
Box 9 Connection Size
List Size 1/2, 3/4, 1, 1 1/2, 2 "
Box 10 Options
DPG Differential Pressure Gauge
FFG Fluid Flow Gauge
FS Flow Switch
PC Particle Counter
SPM Specify Pump & Motor Brand
SP Sample Port
BV Isolation Ball Valve
* Repalcement Parts
9EL5040001 x25 or x40 - Replacement Element 25 or 40 Micron for 91 filter9EL5040401 x25 or x40 - Replacement Element 25 or 40 Micron for 92 filter9OR348 - End Cap O-Ring for both filters9OR351sq - Filter Mount Gasket for both filters9BPA5050001 - ByPass and Magnetic Filter for 91 Filter9BPA5050401- ByPass and Magnetic Filter for 92 Filter9ELWA5040001 - Water Absorbing filter for 91 filter 9ELWA5040401 - Water Absorbing filter for 92 filter
8KLF-51-1000-E-230-60-1-NPT-2
8000 Series Kidney Loop System
8KLF-52-1000-E-230-60-1-NPT-2 8KLF-52-92-25-1000-E-230-60-1-NPT-2
Sample Port (8KLFSP)Fluid Flow Gauge (8KLFFFG)Flow Switch (8KLFFS)Particle Counter (8KLFPC)Differential Pressure Gauge (8KLFDPG)
8000 Series High Flow Magnetic Filtration System for Ferrous and Non-Ferrous Contamination
28
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
28
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
The High Flow Magnetic Filtration Systems are designed for Hydro Carbon Fluids, Chemical and Water.This system is designed to be installed inline
Custom designs and sizes are welcome!
• 2” to 8” Inlet / Outlets: Flange, Threaded or Weld let
• 5SC2P - 2” x 24” (50mm x 600mm) Magnetic Filter
• High Strength Magnetic Patented Technology rated at 300°F - 150°C (600°F - 300°C)
• Cam Lock for easy cleaning
• 2 - ADD-Vantage 9000 Filters mounted in parallel, construction with Stainless Steel elements 100% Reusable
Scrubber
8HF2P - Single 2” MF8HF2PD - Double 2” MF
* Quote per order
Number of Filters
92 - 2 Filters94 - 4 Filters
www.OneEyeIndustries.com
In/Outlet Type Size Height
FLN - Flange 2 to 8 in 24" 60cmNPT - Pipe Thread 50 to 200mmWLD- WeldletBSP- British Thread
HOW TO ORDER...
8HF2P - 92 - FLN - 3 - 24
N E W !
ADD-Vantage 9000 Series
29
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
ADD-Vantage 9000 Series is the combination of two filtration technologies: • Reusable, stainless steel element• Patented magnetic filter technology
The 9000 offers the most advanced filtration on the market today; a reusable, easily cleaned, long life element.• Replaces disposable filters, eliminates environmental taxes
and used filter disposal costs
• Installs just like a disposable filter, no retrofitting is required. Removal and inspection are easy with a built-in Femco® compatible drain plug.
• No other filter on the market can provide the significant savings 2 year payback, 10+ year effective life – and unsurpassed filtering of the ADD-Vantage 9000 Primary Filter
Traps ferrous& non-ferrouscontamination
down tosubmicron levels
which areanalyzed fora predictivemaintenance
program.
The most advanced filtration technology for fluids and oils in the world.
Primary Oil, Fuel & Hydraulic FiltersThe most advanced filtration technology for fluids and oils in the world.
ApplicationsPrimary oil & fuel filter applications • Designed for heavy duty diesel trucks and large capacity die-
sel engine installations in all industries• Extend oil change intervals from 300 to 1000+ hours with oil
analysis• Removes ferrous and non-ferrous contaminants to sub-micron
levels reducing wear cycle on bearings, seals, heads and pis-tons
• Reduces the scoring of fuel injectors increasing fuel economyHydraulics – primary & secondary filtration and suction & return line installations• Removes contaminants that prematurely wear pumps and
seals• Maintains high ISO cleanliness levels, extending fluid life • Reduces corrosion• Amine & glycol • Compressor lube oil • Turbines
Benefits • Continuous total filtration of the most damaging contami-
nants (iron and steel) down to 1 micron.• Flows 40% more fluid than conventional elements• True filtration, no “channeling” or “worm holing”.• Filter elements easily clean in a parts washer or an ultrasonic
cleaner, with solvent, or soap & water or the OEI Enviro Wash Station (see page 34).
• Also fits conventional paper and glass pack filters • Allows inspection of wear metals trapped on the magnetic
filter rod and filter• Eliminates costs of filter stocking and used filter disposal• Eliminates environmental impact from disposal of used filters
& oil and associated environmental taxes• 3 year full warranty, 10+ year effective life• Extend oil change intervals from 300 to 1000+ hours with oil
analysis
Specifications• High flow rate inlet, outlet & filter. Patented bypass and magnetic filter rod.• 10, 25 & 40 micron, absolute rated, filter elements filter down
to 5-7 microns before activating the bypass• Exceeds industry standards for filtration (ISO 4572), bypass
limitations, and collapse pressure (ISO 2941)• 316 stainless steel magnetic filter – continuously filters fer-
rous and non-ferrous contaminants (due to adhesion) to sub-micron levels• Industrial steel machined housing• Femco© drain compatible • Remote mounts, spare parts, o-rings and filter elements are
all available• OEI's Stainless elements with integrated magnetic filter rod,
available for Cat, Waukesha, Cummins and most other brands
We carry a complete stock of replacement O-rings, filter elements, anti-drain back valves, bypass valves and components to repair dam-aged filters.
Check our web site www.OneEyeIndustries.com or contact us directly for more details.
Replacement O-rings, Filter Element & Repair Components
Improves Environmental Footprints
29
30
www.OneEyeIndustries.com
ADD-Vantage 9000 Series
High Flow Dual Filtration SystemThe “High Flow Dual Filtration System” is a combination of two filtration technologies.1) Beta 200 rated reusable stainless steel element
2) OEIs’ patented magnetic filter extracts and traps ferrous and non ferrous contamination.
The ability to remove non-ferrous contamination is through ferrous to non-ferrous abrasive contact and static adhesion.
Employed on a custom OEI high flow filter mount base that allows up to 200 gallons a minute of flow.
This filter is recommended for fuel and light viscous oils.
Available in single and duplex configurations.
9ADV9 - 266FF - NPT# - BDimensions W x D x H Weight - lbs
9ADV9 5 x 5 x 24 22Base 6 x 6 x 5.50 12Inline 5 x 5 x 5.50 7
# Inch In/Outlets
NPT - National PipeBSP - British PipeFLN - FlangeWLD - Weldlet
Mount
B - Base MountI - Inline
5.0"
Length
New Lube Oil and Fluid Dispenser Filtration
How to Order...9ADV9 – 700 - # - #
Designed for filtering new fluids prior to dispensing in the following applications: Lube Oil – Hydraulic – Coolant – Fuel - etc. The ADD-Vantage 700 series is designed with two filtration systems in one, 1st a stainless steel element providing maximum filtration protection, eliminating any chance of “worm holing or channelling” the element is reusable and available in 40, 25 or 10 micron β200 rating. The 2nd is our patented magnetic filter designed creating multiple independent radial magnetic fields filtering contami-nants to sub micron levels.
The ADD-Vantage 700 is rated up to 700 psi and designed with 2” NPT in/outlets and available in a 15” or 27” long unit.
N E W !
Model Box 1 Box 2
9ADV9-700 27 25
Box 1 Filter Body Length
15 15” - Long Body 400 Sq inch media
27 27” - Long Body 850 sq inch media
Box 2 Filter Micron Rating
40 40 Micron Filtration B200
25 25 Micron Filtration B200
10 10 Micron Filtration B200
ADD-Vantage 9000 Series
31
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
31
www.OneEyeIndustries.com
9ADV9 - D9L - PX - x25
Duplex System W x D x H
9ADV9-D9L 12 ½” x 25” x 18” 32mm x 64mm x 46mm
9ADV9-D9XL 12 ½” x 25” x 30” 32mm x 64mm x 76mm
9ADV9 - D9XL - PX - x25
OEI Duplex Filtration System. Designed with OEI’s reusable dual filtration units the stainless steel elements can be removed for cleaning and the magnetic filter inspected for wear contami-nants while your equipment continues to work.
This duplex system is very versatile with multiple port option from ¾” NPTF to 2” NPTF or SAE 12 to
SAE24.
To Order ...
9ADV9 - BOX1 – BOX2 - BOX3
BOX 1Body Length
BOX 2Connection
BOX 3Micron Rating
D9L – 12“ BodyD9XL – 24” Body
PB – 3/4” NPTFPC – 1” NPTFPD – 1 1/4” NPTFPE – 1 1/2” NPTFPF – 2” NPTFPM – 12 SAEPN – 16 SAEPO – 20 SAEPP – 24 SAEPX – Blank Flange
X 25X 40 X 80
X 100
The ADD-Vantage 9000 Series bodies were designed to be held by an adjustable Pin Spanner Wrench while removing or installing the Element Cap.This tool is available at most tool supply companies.
Description: Adjustable Pin Spanner Wrench
Max Capacity: 6-1/4 "
Diameter: 3/8"
Pin Length: 1/4"
Hook Size: 15.32"
Length: 12-1/8"
Part # 1APSW
ADD-Vantage 9000 Wrench
ADD-Vantage 9000 Series
32
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Dual Milling Filtration System
ADD-Vantage 9000 Series
Grease Filtration System
A 100% Reusable Filtration System designed for the machining/milling industry. This ADD-Vantage 9000 (Milling) replaces all conventional disposable filters. Designed with a dual filtration system: Stainless Steel Element with 1/16” perf. screen to trap large particles and OEI’s Patented Magnetic Filter will trap ferrous contaminants to sub-micron levels. Extending the life of your coolant/cutting fluids and equipment. This filter is easily cleaned and has an effective life of 10+ years. A remote mount base is available in 1" and 1-1/2" inlet/outlet. Continuously filters ferrous contaminants to sub-micron levels
Designed to filter grease before it reaches your bearings. The ADD-Vantage 9000 (Grease) filter is equipped with OEI’s Patented Magnetic Filter, trapping ferrous contaminants to sub-micron levels, extending the life of your seals and bearings. This filter is easily cleaned and has an effective life of 10+ years. Sold with a remote base mount, available with a 1" or 1-1/2" inlet/outlet.
This system can be installed remotely on automatic greasing systems such as ATS Electro-Lube, Lincoln, Farval, etc.
For smaller application, install OEI’s Magnetic Y-Strainer
9ADV9 - M - 24M - MillingG - Grease
Length1224
Filter System
5YB1TX
www.OneEyeIndustries.com
9ADV9 - G - 12
OEI has modified its Y-Strainers for smaller inline application for filtering grease. Equipped with OEIs patented Magnetic Filter, this system will trap ferrous contaminants extending the life of your seals and bearings.5YB1TXG - 1” inlet/outlet5YB112TXG - 1½” inlet/outlet
9RMHY5Remote Mount - Hydraulic 1 1/2" In/Outlet Other sizes available
33
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Reusable Oil Filter Magnets
www.OneEyeIndustries.com
THE ENVIRO-WASH 9000
OEI introduces an environmentally friendly and cost effective cleaning system for stainless steel cloth media filter elements. The Enviro-Wash 9000 cleaning system is compact, mobile, user friendly and replaces the tra-ditional ultrasonic cleaning systems.
OEI’s biodegradable cleaning solution will remove carbon, soot, graphite, oils, tars, solvent based products, water repellent greases, waxes, grease, soils and protein deposits.
The Enviro-Wash 9WSH-8 system is designed to clean all our stainless steel cloth media elements. The system operates as a soak and spray process that cycles in 30 minutes from dirty to clean elements and allows the cleaning of (2) 24” elements, (4) 12” elements or (8) 6” elements. The 20 litre envirowash cleaning solution will have a cleaning capacity of 900+ filter elements on average.
The Enviro-Wash 9PWSH-### system is designed as an individual system to clean all our stainless steel cloth media elements. The system operates as a soak and spray and air dry process.
Envirowash 9WSH-8 includes• Mobile wash station 33”W x 25”D x 40”H• 4 - 20 litre pails of envirowash • 6 - Absorbent filter pads• (12) - Element storage bags for 12” elements• (12) - Element storage bags for 24” elements
Envirowash 9000 Consumables • Envirowash solution – available in 20 litre pails• Absorbent filter pads• Element storage bags
We carry all replacement parts for the Envirowash 9000.
9WSH-8
9PWSH-318-elements 1” – 2.8” dia. up to 9” long, 1 Litre of cleaning solution required.
9PWSH-418-elements with a 2.8” – 3.8” dia. up to 9” long, 2 Litre of cleaning solution required.
9PWSH-436-elements with a 2.8” – 3.8” dia. up to 18” long, 4 Litre of cleaning solution required.
9PWSH-620-elements with a 3.8 – 5.8” dia. up to 10” long, 4 Litre of cleaning solution required.
9PWSH-648-elements with a 3.8” – 5.8” ”dia. up to 24” long, 8 Litre of cleaning solution required
9PWSH-###
9WSH-8 9PWSH-###
ADD-Vantage 9000 SeriesN E W !
Reusable Oil Filter Magnets
34
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
34
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Padswww.OneEyeIndustries.com
The filters below are in production, please identify other filters required. Screens are available in 10, 25 & 40 microns. Please specify. Filters for other applications and equipment manufacturers are available on order request (John Deere, Volvo).
ADD-VANTAGE 9000 REUSABLE FILTERS – FOR APPLICATION ON OIL FUEL HYDRAULIC COOLANT SYSTEMS – Cleanable 316 Stainless Steel Element & Magnetic Filter & Internal Bypass – All machined steel Construction. Custom orders for most disposable filter sizes
3.625” OD FILTER DIMENSIONS
Engine Adapters
9ADV9-1000Primary Fuel Filter for most CAT/ Cummins / Detroit / Mac/ Volvo / Mercedes
9EA3010401 Engine Adapter 1” x 14 UN (BF 957)
9SCG20 Gasket 2.47” ID x 2.85” OD
9ADV9-B260 Engine Lube, Compressor Lube and Hydraulic Applications
9EA3010202 Engine Adapter 11/8” x 16 UN
9SCG20 Gasket 2.412” ID x 2.812” OD
9ADV9-B262 Engine Lube, Compressor Lube and Hydraulic Applications
9EA3010201 Engine Adapter 1” x 12 UN
9SCG20 Gasket 2.412” ID x 2.812” OD
9ADV9-PH3976A Engine Lube, Compressor Lube and Hydraulic Applications
9EA3010101 Engine Adapter 1” x 16 UN
9SCG20 Gasket 2.47” x 2.85”
9ADV9-B237 Engine Lube, Compressor Lube and Hydraulic Applications
9EA3010301 Engine Adapter 3/4" x 16 UN
9SCG20 Gasket 2.455” ID x 2.835” OD
3.625” COMMON FILTER COMPONENTS
9B3020201 Canister Body 3.625: x 7.5L
9EC3030001 Filter End Cap
9BPA3050201 Bypass & Magnetic Filter 73mm x 1Bar/w 25RNC516525
9BPS3060001 Bypass Coil Spring
9OR218 Filter Element O-Ring
9OR236 End Cap O-Ring
9DP263750 Drain Plug 3/4" x 16 SAE
9CG263860 Drain Plug Gasket 3/4"
9EL3040201 S/S Filter Element
4.25” OD FILTER DIMENSIONS
Engine Adapters
9ADV9-PH49A CAT/ Volvo/ Mack: CAT 1R0658, 1R0714, 1R0739 1R1807, 2P4004, 2Y8096
9EA4010301 Engine Adapter 1 1/8” x 16 UN
9SCG9 Gasket 3.59” ID x 4.01” OD
9ADV9-B7155 Hitachi Excavators, Kobelco Wheel Loader
9EA4010401 Engine Adapter 1 1/2” x 16 UN
Gasket 3.875” ID x 4.315 OD
9ADV9-PH3786 Ford / IHC Trucks w/ 7.3 Turbo Diesel (94-03)
9EA4010201 Engine Adapter 1 1/2” x 16 UN
Gasket 3.692 x 4.0112”
9ADV9-0958 K2000 Fuel Primary
9EA5010203 Engine Adapter 1 1/8" x 12 UN
9SCG18 Gasket 3.85" ID x 4.35 OD
9ADV9-0959 K2000 Fuel Secondary
9EA5010204 Engine Adapter 1 1/16" x 16 UN
4.25” COMMON FILTER COMPONENTS
9B4020001 Canister Body 4.25” OD x 9.90L
9EC4030001 Filter End Cap
9BPA4050001 Bypass & Magnetic Filter 94.5mm x 1Bar/w 25RNC5166
9BPS4060001 Bypass Coil Spring
9OR226 Filter Element O-Ring
9OR242 End Cap O-Ring
9DP263750 Drain Plug 3/4" x 16 SAE
9CG263860 Drain Plug Gasket 3/4"
9EL4040101 S/S Filter Element
5.0” OD FILTER DIMENSIONS
Engine Adapters
9ADV9-0755 Cat 1R-0755
9EA5010202 Engine Adapter 1 3/8” x 16 UN
9SCG18 Gasket 3.85” ID x 4.35” OD
9ADV9-4005 Cat C15,C12, C10, C16, 3406, 3408
9EA5010201 Engine Adapter 1 1/2 x 16 UN
9SCG7 Gasket 3.85” ID x 4.21” OD
9ADV9-3566 Cat 1R1808
9EA5010007 Engine Adapter 1 1/2" x 16 UN
9SCG18 Gasket 3.845” ID x 4.35 OD
9ADV9-3612 Cummins K2000, Detroit Diesel
9EA5010004 Engine Adapter 1 1/16” x 16 UN
9SCG10 Gasket 3.64 ID x 4.31” OD
9ADV9-3671 Detroit Diesel 50,60 Series LF3671
9EA5010002 Engine Adapter 1 5/8” x 12 UN
9SCG18 Gasket 3.845” ID x 4.35 OD
9ADV9-0495 Detroit Diesel 50, 60 Series Power Guard B495
9EA5010001 Engine Adapter 1 5/8” x 12 UN
9SGC10 Gasket 3.64” ID x 4.31” OD
9ADV9-3555 Cat, Cummins, Volvo. IHC, John Deere, P3555A
9EA5010005 Engine Adapter 1 3/8” x 16 UN
9SCG7 Gasket 3.85” ID x 4.21” OD
9ADV9-7138 IHC, Detroit Series 40
9EA5010006 Engine Adapter 36mm x 1.5
9SCG10 Gasket 3.64” ID x 4.31” OD
9ADV9-3000 N14 Cummins
9EA5010101 Engine Adapter 2 1/4" x 12 UN
9SCG3 Gasket 4.06” ID x 4.58” OD
9ADV9-9001 Cummins ISX, ISB, ISC, ISM
9EA5010003 Engine Adapter 95mm x 2.5
9SCG8 Gasket 4.11” ID x 4.31” OD
9ADV9-9024 Cummins QSK60
9EA5010010 Engine Adapter 90mm x 2.0
Gasket 4.0” x 4.68” OD
5.0”OD COMMON FILTER COMPONENTS
9B5020101 Canister Body N14
9B5020001 Canister Body 5” OD x 12 5/8” L
9B5020202 Canister Body 5” OD x 9 7/8” L
9EL5040001 S/S Filter Element for 12 5/8” Body & N14
9EL5040002 S/S Filter Element for 9 7/8” Body
9BPA5050001 Bypass & Magnetic Filter (25RNC387) 12 5/8 Body
9BPA5050002 Bypass & Magnetic Filter (25RNC3845) 9 7/8 Body
9BPS5060001 Bypass Coil Spring
9OR230 Filter Element O-Ring
9OR348 End Cap O-Ring
9DP263750 Drain Plug 3/4" x 16 SAE
9CG263860 Drain Plug Gasket 3/4"
9EL4040001 S/S Filter Element
9EC4030001 Filter End Cap
34
Industrial Filtration Solutions
35
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
35
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on PadsISO 9000 • To order any other parts not listed above, please contact us.
ADD-VANTAGE 9000 HYDRAULIC FILTER
9ADV9-926170 Short Version
9B5020002 Canister Body 5” OD x 9 7/8” L
9EL5040002 S/S Filter Element 25 Micron 4.17 OD x 2.83” ID x 7.00” L
9BPA5050002 Bypass & Magnetic Filter 1 Bar – 25RNC384.75
9ADV9-926170L Standard
9B5020001 Canister Body 5” OD x 12 5/8” L
9EL5040001 S/S Filter Element 25 Micron 4.17” OD x 2.83” ID x 9.73” L
9BPA5050001 Bypass & Magnetic Filter 1 Bar – 25RNC387
9ADV9-926170LX2 Long Version
9B5020401 Canister Body 5” OD x 24” L
9EL5040401-B S/S Filter Element 25/40 Micron 4” OD x 2.83” ID x 21.6” L
9BPA5050401 Bypass & Magnetic Filter 1 Bar – 25RNC3819
9ADV9-266-FF High Flow Filter
9EA61010 Mount Adapter w/2” Flange
9B5020401 Canister Body 5” OD x 24” L
9EL5040401-B S/S Filter Element 25/40 Micron 4” OD x 2.83” ID x 21.6” L
9BPA5050401 Bypass & Magnetic Filter 1 Bar – 25RNC3819
Common Filter Components
9EA5010008 Mount Adapter 1 1/2" x 16 UN
9BPS5060001 Bypass Coil Spring
9EC5030001 Filter End Cap
9OR230 Filter Element O-Ring
9OR348 End Cap O-Ring
9DP263750 Drain Plug 3/4" x 16 SAE
9CG263860 Copper Gasket 3/4”
ADD-VANTAGE 9000 MILLING FILTER
9ADV9-M-12
9B5020001 Canister Body 12 5/8”
9EL5040003 S/S Filter 1/8” Perf. 4.17 OD x 2.83 ID x 9.7 L
9BPA5050001 Bypass & Magnetic Filter 1 Bar – 25RNC387
9ADV9-M-24
9B5020401 Canister Body 24”
9EL5040004 S/S Filter 1/8” Perf. 4.17 OD x 2.83 ID x 19.5 L
9BPA5050401 Bypass & Magnetic Filter 1 Bar – 25RNC3819
Common Filter Components
9EA5010008 Mount Adapter 1 1/2" x 16 UN
9BPS5060001 Bypass Coil Spring
9EC5030001 Filter End Cap
9OR230 Filter Element O-Ring
9OR348 End Cap O-Ring
9DP263750 Drain Plug 3/4" x 16 SAE
9CG263860 Copper Gasket 3/4”
ADD-VANTAGE 9000 GREASE FILTER
9ADV9-G-12
9EA5003901 Mount Adapter 1 1/2” x 16 UN w/ Solid Element
9B5020001 Canister Body 5” OD x 12 5/8” L
9EC50300003 End Cap w/ 3R8 Magnetic Filter
9OR348 End Cap O-Ring
9000 SERIES REMOTE FILTER BASE MOUNT
9RM3000 Base Mount for 9ADV9-3000 N-19
9RM3612 Base Mount for 9ADV9-3612
9RMHY5 Base Mount for 9ADV9-926170L
9RM266 Base Mount for High Filtration System
STAINLESS STEEL REPLACEMENT ELEMENTS – Lube and Hydraulic Applications Custom element sizes are available. – All OEI elements come with magnetic filters – Replace OEM Disposable Elements with OEI Stainless Steel Elements.
9ELSS9600825 Stainless Element 25 Micron Absolute/10 micron Nominal 8" L
9ELSS9600840 Stainless Element 40 Micron Absolute/10 micron Nominal 8" L
9ELSS96001625 Stainless Element 25 Micron Absolute/10 micron Nominal 16" L
9ELSS96001640 Stainless Element 40 Micron Absolute/10 micron Nominal 16" L
9ELSS9800825 Stainless Element 25 Micron Absolute/10 micron Nominal 8" L
9ELSS9800840 Stainless Element 40 Micron Absolute/10 micron Nominal 16" L
9ELSS98001625 Stainless Element 25 Micron Absolute/10 micron Nominal 8" L
9ELSS98001640 Stainless Element 40 Micron Absolute/10 micron Nominal 16" L
STAINLESS STEEL SUCTION STRAINERS – Stainless Steel Suction Strainers w/magnetic filter
9ELSSSSNPT38 S/S Suction Strainer 3/8" NPT 1.80" OD X 3.50" L
9ELSSSSNPT12 S/S Suction Strainer 1/2" NPT 1.80" OD X 4.20" L
9ELSSSSNPT34 S/S Suction Strainer 3/4" NPT 2.60" OD X 4.10" L
9ELSSSSNPT100 S/S Suction Strainer 1" NPT 2.60" OD X 5.50" L
9ELSSSSNPT114 S/S Suction Strainer 1-1/4" NPT 3.40" OD X 7.70" L
9ELSSSSNPT112 S/S Suction Strainer 1-1/2" NPT 3.40" OD X 8.90 "L
9ELSSSSNPT200 S/S Suction Strainer 2" NPT 3.40" OD X 10.0" L
9ELSSSSNPT212 S/S Suction Strainer 2-1/2" NPT 5.90" OD X 8.40" L
9ELSSSSNPT300 S/S Suction Strainer 3" NPT 5.90" OD X 10.7" L
35
ADD-VANTAGE 9000 DISPOSABLE CELLULOSE ELEMENTS
9ELDP3040201 Filter Element 2.76"od x 1.6"id x 6.69"L 10 Micron Nominal
9ELDP4040101 Filter Element 3.54"od x 2.28"id x 7.48"L 10 Micron Nominal
9ELDP5040002 Filter Element 4.17" od x 2.83" id x 7.0 L 10 Micron Nominal
9ELDP5040001 Filter Element 4.17"ood x 2.83"id x 9.73"L 10 Micron Nominal
9ELWA5040001 Filter Element 4.17"ood x 2.83"id x 9.73"L Water Absorbing
9ELWA5040002 Filter Element 4.17" od x 2.83" id x 7.0 L Water Absorbing
9ELWR5040401 Filter Element 4.00"ood x 2.83"id x 21.6"L Water Absorbing
ADD-Vantage 9000 Series
N E W !
36
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Reusable Oil Filter Magnets
CAT Filters Threading Dimension Gasket ADD-Vantage 9000Reusable/Cleanable
077-3058 1 1/2 x 16 5 x 7 none 9ADV9-926170077-3492 1 x 12 3 x 5 2.81 - 2.42 9ADV9-B262093-7521 1 1/8 X 16 4 X 7 2.83 - 2.46 9ADV9-B260102-2828 1 3/8 x 12 4 x 9 2.76 - 2.48 9ADV9-8878108-1153 1 3/4 x 12 11.63 L X 4.77 3.39 - 3.11 9ADV9-0973121-9868 1 3/8 X 12 4 X 6 2.76 - 2.48 9ADV9-8878126-1813 2 x 12 9.52 L X 3.13 3.13 - 1.86 9ADV9-1814126-1814 2 x 12 9.52 L X 3.13 3.13 - 1.86 9ADV9-1814126-1815 1 3/8 X 12 4 X 6 2.76 - 2.48 9ADV9-8878126-1816 1 3/4 x 12 5 x 8 3.34 - 3.13 9ADV9-6636
126-1817 1 3/4 x 12 5 x 12 3.39 - 3.11 9ADV9-0973
126-1818 1 3/8 x 12 4.7 x 11.6 2.76 - 2.48 9ADV9-8878129-0373 1 X 14 4.25 X 11.3 3.5 - 3.18 9ADV9-0373130-3212 2 x 12 3 x 9 3.13 - 1.86 9ADV9-1814
133-5673 1 X 14 4.25 X 11.3 3.5 - 3.18 9ADV9-0373
134-3014 1 3/4 x 12 5 x 12 3.35 - 3.11 9ADV9-0973144-0832 1 1/2 x 16 5 x 7 none 9ADV9-926170144-6691 1 3/8 X 12 4 X 6 2.76 - 2.48 9ADV9-8878152-6902 1 3/4 x 12 5 x 14 3.34 - 3.11 9ADV9-0973156-0214 1 3/8 x 12 4 x 9 2.76 - 2.48 9ADV9-8878185-0337 2 X 12 3 X 9 3.13 - 1.86 9ADV9-1814198-3188 1 1/2 x 16 5 x 11 none 9ADV9-926170L937-521 1 1/8 x 16 3.69 x 5.2 2.81 - 2.42 9ADV9-B2601G-8878 1 3/8 x 12 4 x 9 2.76 - 2.48 9ADV9-88781P-2299 1 x 14 3.65 x 7 2.81 - 2.42 9ADV9-10001R-0658 1 1/8 - 16 4.25 x 10.3 3.89 - 3.55 9ADV9-PH49A1R-0712 1 x 14 9.43L X 3.72" 2.81 - 2.42 9ADV9-1000
1R-0713 1 1/8 - 16 3.69 x 5.2 2.81 - 2.42 9ADV9-B260
1R-0714 1 1/8 - 16 4.28 x 6 3.97 - 3.59 9ADV9-PH49A1R-0716 1 1/2 -16 5.3 x 12 4.31 - 3.92 9ADV9-40051R-0734 1 X 12 5.35L X 3.66 2.81 - 2.42 9ADV9-B2621R-0739 1 1/8 x 16 4.282 x 10.3 3.96 - 3.58 9ADV9-PH49A1R-0749 1 x 14 3.68 x 9.5 2.83 - 2.46 9ADV9-10001R-0750 1 x 14 3.68 x 7 2.83 - 2.46 9ADV9-10001R-0751 7/8 X 14 3.1 X 7.0 2.5 - 2.25 9ADV9-07511R-0755 1 3/8 x 16 5.3 x 12 4.28 - 3.9 9ADV9-07551R-0762 1 X 14 3.7 - 10.75 3.6 - 3.03 9ADV9-07621R-0769 1 X 14 4.24 X 9.90 4.25 - 3.68 9ADV9-07691R-0771 1 X 14 4.25 X 9.37 4.24 - 3.68 9ADV9-07691R-1807 1 1/8 x16 4 x 10.38 3.97 - 3.59 9ADV9-PH49A1R-1808 1 1/2 x 16 5.3 x 12 4.31 - 3.92 9ADV9-35661W-2660 1 1/2 x16 5.3 x 12 4.31 - 3.92 9ADV9-35661W-8845 1 3/8 x 16 4.66 x 9.75 4.32 - 3.85 9ADV9-0755207-5035 1 3/4 x 12 5 x 14 3.34 - 3.11 9ADV9-0973223-7809 1 1/2 x 16 5 x 7 none 9ADV9-926170225-4118 1 3/4 x 12 5 x 12 3.38 - 3.10 9ADV9-0973
ADD-Vantage 9000 Series
ISO 9000 • To order any other items not listed above, please contact us.
37
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Reusable Oil Filter Magnets
CAT Filters Threading Dimension GasketADD-Vantage 9000Reusable/Cleanable
244-4484 1 1/2 x16 4.65 x 11.73 4.32 - 3.85 9ADV9-3566272-1788 1 1/2 x 16 5.3 x 12 4.31 - 3.92 9ADV9-4005275-2604 1 1/2 x 16 5.3 x 12 4.31 - 3.92 9ADV9-40052P-4004 1 1/8 - 16 4.25 X 10.3 3.89 - 3.55 9ADV9-PH49A2P-4005 1 1/2 x 16 5.3 x 12 4.31 - 3.92 9ADV9-40052Y-8096 1 1/8x 16 4.25 x 10.3 3.89 - 3.55 9ADV9-PH49A2Y-8097 1 1/2 x16 5.3 x 12 4.31 - 3.92 9ADV9-40052Y-8670 1 x 14 3.66 x 6.85 2.81 - 2.42 9ADV9-1000326-1643 1 X 14 4.25 x 9.3 4.25 -3.85 9ADV9-1643326-1644 1 x 14 4.25 x 7.6 4.25 - 3.7 9ADV9-16434I-3948 2 x 12 3 x 9 3.13 - 1.86 9ADV9-18144I-3950 2 x 12 3 x 9 3.13 - 1.86 9ADV9-18144T-6788 1 1/2 x 16 5 x 7 none 9ADV9-9261704T-6915 1 1/8 X16 4 X 6 2.72 - 2.41 9ADV9-B2607W-2326 3/4 x 16 3.81 x 6.78 2.82 - 2.42 9ADV9-B2377W-2327 3/4 x 16 3.66 x 5.35 2.81 - 2.41 9ADV9-B2379N-5570 1 1/8 x 16 3.81 x 5.22 2.81 - 2.42 9ADV9-B2379N-6007 1 1/8 x 16 4.28 x 5.78 3.97 - 3.59 9ADV9-PH37869T-0973 1 3/4 x 12 11.63L X 4.77 3.39 - 3.11 9ADV9-09739T-6636 1 3/4 x 12 5 x 8 3.34 - 3.13 9ADV9-66369T-8578 1 1/2 x 16 5 x 7 none 9ADV9-9261709U-5870 1 1/2 x 16 5 x 11 none 9ADV9-926170L9U-6983 1 1/2 x 16 5 x 11 none 9ADV9-926170L9U-6984 1 1/2 x 16 5 x 11 none 9ADV9-926170L9U-6985 1 1/2 x 16 5 x 11 none 9ADV9-926170L
CAT Filters Element DimensionADD-Vantage 9000Reusable/Cleanable
054-1719 element 9.02L X 1.61 X 3.85 9ELSSK409X25077-5479 element 9.02L X 1.61 X 3.85 9ELSSK409X25086-3940 element 9.02L X 1.61 X 3.85 9ELSSK409X25094-4412 element 17.7L x 5.8 x 4.3 9ELSS5818x40132-8875 element 9.25L x 4.0 x 2.27 9ELSS773X40132-8876 element 9.0L x 5.07 x 3.34 9ELSS778X40134-0964 element 8.03L 3.1 X 1.71 9ELSS96008X25139-1536 element 11 X 5.07 X 3.34 REVERSE FLOW 9ELSS722X40139-1537 element 7.0 X 5 1/8 X 3 3/8 9ELSS5077X25167-2009 element 9.0 X 6.84 X 3.94 9ELSS709X40179-9806 element 16 3/4 X 5 5/8 X 3 7/8 9ELSS9806X25249-2337 element 9.0 X 6.75 X 4.25 REVERSE FLOW 9ELSS7409X25328-3655 element 10.5 X 5.0 X 2.0 9ELSS1809X251M-9156 element 9.25L x 4.0 x 2.27 9ELSS773X251R-0719 element 9.25L x 4.0 x 2.27 9ELSS773X401R-0722 element 11 X 5.07 X 3.34 9ELSS722X40
ISO 9000 • To order any other items not listed above, please contact us.
ADD-Vantage 9000 Series
38
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Reusable Oil Filter Magnets
1R-0726 element 10 1/4 X 7 3/8 X 2 7/8 9ELSS726X401R-0728 element 9.0 X 3.0 X 1.6 9ELSS728X401R-0732 element 9.0 X 6.84 X 3.94 9ELSS709X251R-0735 element 7.0 X 5. 0 X 3.34 9ELSS507X251R-0741 element 9.0 X 5.0 X 3.34 9ELSS778X401R-0746 element 5.65 X 3.0 X 1.06 9ELSS746X401R-0756 element 9.0 X 3.0 X 1.6 9ELSS728X40
1R-0773 element 9.25L x 4.0 x 2.27 9ELSS773X40
1R-0774 element 11 X 5.0 X 3.34 9ELSS774X40
1R-0777 element 7.0 X 5.0 X 3 3/8 9ELSS507X25
1R-0778 element 9.0L x 5.07 x 3.34 9ELSS778X40
1R-1809 element 10.5 X 5.0 1.15 9ELSS1809X251S-9150 element 9.0 X 3.0 X 1 7/16 9ELSS9150X252J-1560 element 9.0L x 5.07 x 3.34 9ELSS778402M-3943 element 9.25L x 4.0 x 2.27 9ELSS773402P-5835 element 5.65 X 3.0 X 1.06 9ELSS5834X254A-0332 element 9.0 X 3.0 X 1 7/16 9ELSS9150X254J-0806 element 9.0L x 5.07 x 3.34 9ELSS778404J-6064 element 9.0L x 5.07 x 3.34 9ELSS778404P-2839 element 10 5/5 X 7 3/8 X 2 7/8 9ELSS726X40
4T-3131 element 9.25L x 4.0 x 2.27 9ELSS77340
4T-3132 element 9.0L X 5.07 X 3.34 9ELSS778254T-3133 element 9.0 X 6 3/4 X 4.0 9ELSS709X254T-3134 element 11 X 5.0 X 3.34 REVERSE FLOW 9ELSS722X405S-0484 element 9 5/16 X 4.0 X 1 5/8 9ELSS484X407J-0670 element 9.0 X 6 3/4 X 4.0 9ELSS709X257J-0732 element 9.0 X 6.84 X 3.94 9ELSS709X257M-3800 element 9 5/16 X 4.0 X 1 5/8 9ELSS484X407N-7500 element 10 5/16 X 7 3/8 X 2 7/8 9ELSS726X409F-6700 element 9 5/8 X 4.0 X 1 5/8 9ELSS484X409H-1252 element 6.5 X 3 5/16 X 1 1/16 9ELSS8792X259J-5461 element 11 X 5.0 X 3.34 9ELSS722X409M-9740 element 9.25 X 4.0 X 2.27 9ELSS773X40
CAT Filters Element DimensionADD-Vantage 9000Reusable/Cleanable
ISO 9000 • To order any other items not listed above, please contact us.
39
ISO 9000 • Reusable • 1 Year Warranty on Pads • 5 Year Life on Pads
Reusable Oil Filter MagnetsScrubber Flow Rates
ScrubberModel 5SC349SCL 5SC12SCL 5SC24SCL 5SC36SCL 5SC212SCL 5SC224SCL
Viscosities BasecSt @ 40C
Water, Coolant Deisel Fuel (1 - 30 St)Single Pass Filtration GPM 8 21 40 60 50 98Multi Pass Filtration 30 81 95 122 200 400
Engine, Gear andHydraulic Oil / cStSAE 10 (40 - 110 cSt)Single Pass Filtration GPM 7 20 38 55 50 98Multi Pass Filtration 30 65 80 90 190 380
SAE 20 (220 cSt)Single Pass Filtration GPM 6 15 30 45 40 70Multi Pass Filtration 15 41 76 75 133 200
SAE 30 (460 cSt)Single Pass Filtration GPM 5 12 20 25 25 40Multi Pass Filtration 10 25 30 35 65 95
SAE 40 (680 cSt)Single Pass Filtration GPM 3 6 10 12 12 20Multi Pass Filtration 5 13 16 20 40 65
Gear Oil (1000 cSt)Single Pass Filtration GPM 0 3 5 6 8 15Multi Pass Filtration 0 5 8 11 22 40
www.OneEyeIndustries.com
LIMITED WARRANTY3 Year Limited Warranty on 2000, 3000, 4000, 5000 and 8000 Series inclusive plus ADD-Vantage 9000
Series (Ten year life expectancy).
1 Year Limited Warranty on 500, 800, 900 and 7000 Series (Five year life expectancy).
The exclusive remedy for breach of this warranty is replacement of any product which the buyer, within the warranty period, has notified the Seller in writing to be defective, and which the Seller has deter-mined to be defective. If the buyer has submitted a warranty registration card for the product, the notice of the defect must include a proof of purchase. The Buyer will be responsible for all costs of shipment of replacement parts. In no event will the Seller’s liability for any damage exceed the purchase price of the product. SELLER WILL NOT BE LIABLE TO THE BUYER FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES INCLUDING, WITHOUT LIMITATION, LOST REVENUES OR PROFITS, EXPENSES RELATED TO TRAVEL, AND LOSS DUE TO PERSONAL INJURY. The sole purpose of the stipulated remedy shall be to provide the Buyer with free replacement of defective parts in the manner provided herein. This exclusive remedy shall not be deemed to have failed of its essential purpose so long as the Seller is willing and able to replace defective parts in the prescribed manner. SUCH WARRANTY IS EXTENDED ONLY TO THE ORIGINAL BUYER OF THE FILTER MASTER AND DOES NOT EXTEND TO A REPURCHASER OF THE PRODUCT. THE WARRANTIES IN THIS AGREEMENT ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND SUCH OTHER WARRANTIES ARE EXPRESSLY DISCLAIMED. THE SELLER HAS NOT MADE AND DOES NOT HEREBY MAKE ANY OTHER REPRESENTATION, WARRANTY OR COVENANT WITH RESPECT TO THE CONDITION, QUALITY, DURABILITY, DESIGN, OPERATION, CAPACITY, FITNESS FOR USE, OR SUITABILITY OF THE EQUIPMENT. THIS WARRANTY DOES NOT COVER PARTS THAT ARE SUBJECT TO NORMAL WEAR AND/OR DETRIMENTAL EFFECTS OF EROSION, CORROSION OR TEMPERATURE. CUSTOM PRODUCTS will have their own warranty supplied.
REV2012