herohog.comherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms... · 2018-08-20 · DIY METAL...
Home
/
Documents
Post on 04-Jun-2020
213 views
48 download
Preview:
Click to see full reader
Report this document
SHARE
transcript
Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Top related
The DIY Sheet Metal Self-Loading Pistolherohog.com/GunBuilds/Practical_Scrap_Metal_Small...Practical Scrap Metal Small Arms Plans on pages 12 to 15. Introduction The pistol design
Documents
HeroHog.comherohog.com/GunBuilds/Practical_Scrap_Metal_Small...Drill a pocket and insert a small compression spring in position shown on sear 2 inches Print on US letter paper Lower
Documents
By Professor Parabellumherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms_Vol.08-9mm_Bullet_Hose.pdfConstructed in it's most concealable form very little protrudes, keeping a slim
Documents
HeroHog.comherohog.com/...Arms_Vol.15-Self-Loading_Pistol_MK3.pdf · SHEET METAL SELF-LOADING PISTOL Professor Parabellum Slide rails The slide rails are made by cutting two strips
Documents
herohog.comherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms_Vol.14-Break... · The Ultimate DIY Machine Pistol Metal Arms Vol.ll THE DIY SHEET METAL SELF-LOADING PISTOL Smut
Documents
Introduction - Hero Hogherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms... · 2018. 8. 20. · 1/4” (6mm) or 12mm mild steel plate 5/8” (16mm) mild steel bar If a welder
Documents
herohog.comherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms... · 2018-08-20 · A second drill bit is modified by grinding off its tip and is used to finish the flat profile
Documents
The MAC-10 Construction Guideherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms...using either a dremel type rotary tool fitted with a 'reinforced cutting disc' or by drilling
Documents
herohog.comherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms... · 2018-08-20 · SELF-LOADING PISTOL CONSTRUCTION PIANS By professor 9MM BULLET HOSE HOMEBUILT SUBMACHINE GUN
Documents
herohog.comherohog.com/.../Practical_Scrap_Metal_Small_Arms_Vol.19-.22_Revol… · DIY .22 Revolver Construction Plans Professor Parabellum . The following drawings are reverse engineered
Documents
The Box Tube MAC-11 - HeroHog.comherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms... · 2018. 8. 20. · The Box Tube MAC-11 ... Practical Scrap Metal Small Arms Vol.II By Professor
Documents
herohog.comherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms_Vol.13-9mm_semi... · Striker spring 4 3/4" (120mm) 19mm 1 3/4" 1.5mm wire Unmodified purchased compression spring
Documents
Practical Scrap Metal Small Arms Volherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms_Vol.10-T… · barrel is permanently destroyed & blocked with its bolt containing no provisions
Documents
The DIY STEN Gun - Hero Hogherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms_Vol.03-… · Practical Scrap Metal Small Arms Vol.3 By Professor Parabellum Plans on pages 11 to
Documents
Introduction - Hero Hogherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms... · 2018-08-20 · PPSH41 7.62 x 25 590g UZI 9x19 680g Lusa 9x19 482g VZ61 .32 ACP 230g Micro UZI 9x19
Documents
DIY Sheet Metal Derringers - Hero Hogherohog.com/GunBuilds/Practical_Scrap_Metal_Small_Arms...DIY Sheet Metal Derringers The following simple .22 rimfire designs utilize sheet metal
Documents