Post on 03-Dec-2014
transcript
Goal of my project:
Over the years induction motor has been utilized as a workhorse in the electrical industry
Due to its easy construction, high robustness and generally satisfactory efficiency with
the invent of high speed power semiconductor devices three-phase inverter play the key
role for variable speed ac motor drives. Traditionally six switches, 3 phase inverters have
been widely utilized for variable speeds induction motor drives. This involves the losses
of the six switches as well as the complexity of the control algorithms and interface
circuits to generate six PWM logic signals.
In the past researches mainly concentrated on the development of the efficient control
algorithms for high performance variables speed induction motor drives, however the
cost, simplicity and flexibility of the overall drive system which becomes some of the
most important factors did not get that much attention to the researchers in this area most
of the developed control system failed to attract the industry.
1
INTRODUCTION:
Induction motors are being used for many industrial and commercial applications because
it its easy build, high robustness, and generally satisfactory efficiency. AC induction
motors, which contain a cage, are very popular invariable-speed drives. They are simple,
rugged, inexpensive and available at all power ratings. Progress in the field of power
electronics and microelectronics enable the application of induction motors for high-
performance drives. The speed of the induction motor can be controlled by varying its
input AC voltage and frequency using an Inverter. A standard six - switch three phase
voltage source inverter has six switches in three legs with a pair of complementary power
switches per phase. A reduced switch count voltage source inverter i.e. four switch three-
phase inverter (FSTPI)] uses only two legs, with four switches. The advantage of this
inverter due to the use of 4 switches instead of conventional 6 switches is lesser
switching losses, lower electromagnetic interference (EMI), less complexity of control
algorithms and reduced interface circuits. Several articles report on FSTPI structure.
Power semiconductor devices constitute the heart of the modern power electronics, and
are being extensively used in power electronic converters in the form of a matrix of on -
off switches, and help to convert power from one form to another. There are four basic
conversion functions that can be implemented namely; ac to ac, ac to dc, dc to ac and dc
to dc. The switching mode power conversion gives high efficiency but the disadvantage
is that due to the non- linearity of the switches, harmonics are generated in both the
supply and load sides. The switches are not ideal and they have conduction, turn-on and
turn off switching losses. Although the cost of the power semiconductor drives, may
hardly exceed 20-30 percent, the total equipment cost and performance may be highly
influenced by the topology of the circuit used for power conversion. Owing to the
development of power electronics in power conversion, AC adjustable speed drives are
becoming more and more popular for industrial applications. This equipment improves
energy efficiency, but there are key issues, like efficiency and harmonic injection into the
line, which affects the power factor, and the overall cost of the system, and these issues
need to be considered before any drive is used for industrial or commercial purpose.
2
One way to increase the efficiency of the drive is by reducing the losses at possible places
such as in the converter used along with the ac motor. These losses are computed as
switching losses and conduction losses. It may also be improved as the number of circuit
elements is minimized, because as the number of devices reduces the associated amount
of switching reduces and so the losses are minimized.
Proliferation of nonlinear loads, such as three-phase rectifiers, adjustable speed drives
and uninterruptible power supplies are prone to high harmonic injection into the utility,
which powers them. To reduce harmonic injections, improvement in displacement factor
is considered and so power factor correction equipment like capacitors and filters are
installed in the system. Harmonic currents cause resonance between utility and
harmonic–producing loads or among multiple harmonic producing loads. These harmonic
related phenomena result in de-rating of the system equipment such as transformers,
higher transmission line loss and reduced system stability margin. Since electrical motors
consume around 56% of the total consumed electrical energy the improvement in power
factor of electrical drives as seen by the utility connection has been of major concern.
Another consideration is the need to increase the VA capacity of motor drives, so that the
full utilization of the isolated real power is possible.
In order to solve some of these problems, a large variety of control techniques and
converter topologies have appeared in the literature. Since good quality power factor
systems are becoming more and more mandatory, power factor improvement is one of the
key issues in designing a system.
Several methods have been attempted in order to obtain a satisfactory
power quality from the supply mains. The use of terminal capacitors
across the machine windings is very common, due to its low cost and
simplicity. However, this method is often not often recommended for
the adjustable speed drives employing inverters which are PWM operated, as
the capacitor may draw high harmonic currents due to the harmonics present in the PWM
terminal voltages, and the motor may experience self-excitation, which might cause over-
voltages in its terminals.
In rural electric systems, the cost of bringing three-phase power to a remote location is
often high due to high cost for a three-phase extension. Furthermore the rate structure of a
3
three-phase service is higher than that for single-phase service. Therefore, single-phase to
three-phase power converters are excellent choices for situations where three-phase
power is not available. Such converters have a wide range of applications in which a
three-phase motor is a main component and the available supply is single-phase. Other
factors that influence the choice of a static converter and three–phase motor combination
are listed as follows:-
1. Three–phase motors are more efficient and economical than their single-phase
counter parts.
2. Starting and inrush currents in a three-phase motor are less severe than in a single-
phase motor.
Owing to wide applications of power converters, it is essential to
develop single to three-phase converters, which are efficient, cost
effective and give high quality performance. Presently, available
converters for such applications are classified as rotary type;
autotransformer with switched capacitors and lastly, the static
converter type. The first two types of converters as given in employ
bulky magnetic components of considerable size and weight. The third
category that employs static semiconductor devices for direct
conversion of single-phase to three-phase is by far the most active
research area in which the bulky magnetic part can be eliminated and
embedded control of the line and the load can be achieved. The superiority of static
converters is further reinforced with the advances in power semiconductor devices and
their control logic.
Previous work on static single-phase converters involves the use of thyristors in
combination with L, C components, as in. The disadvantage of this scheme is the limited
control range and the L-C values must be matched with the load impedances. Moreover
the circuit topology is bulky due to the reactor used with the input. In a number of
reduced switch count converter topologies for generating high quality three-phase
voltages from single-phase mains have been presented, in which the converters were
classified as active input current shaping feature ones and those without the active input
4
current shaping feature. The converters, which do not employ the input current shaping
feature have reduced number of switches when compared to ones in which this feature
was included, but in both types the converter size is large due to the inductor, in series
with the single-phase supply.
In a new single-phase to three phase converter for low cost ac motor
drive was presented, which employed only six switches and
incorporates an active input current shaping feature that results in
sinusoidal input current close to unity power factor. This converter has
the capability of bidirectional power transfer, an improvement on all
the previously proposed converters. In new topologies for single to
three-phase power conversion was proposed in which the zero
sequence voltage was used to control the supply side parameters. This
allowed the integration of the load and supply control, and with this
class of converters unity power factor operation was possible. Low power
drive systems typically in the range of fractional horse-power (hp) to 1 hp, due to their
massive emerging applications in appliances and in industrial processes have been of
great interest for researchers to explore their performance while improving the same. For
these low power drives it is very common to use the single-phase to three-phase type of
converter to drive the motor. The usual approach for these adjustable speed drives is to
implement the power factor correction (PFC) feature in the power converter itself, which
normally requires additional circuitry and controls. Some analysis has been done in order
to evaluate the impact of these PFC schemes in the drive system in terms of performance
and costs. It was concluded that, though a good system input power factor improvement
can be achieved, the used of additional PFC control feature may not be very attractive for
induction motor drives, due to cost and packaging factors. Hence, in order to make this
scheme more cost effective, it is important to develop power converters with PFC
schemes using a reduced number of components and more integrated controls.
Due to the variety of the topologies and control strategies, the
converter topologies have been differentiated as Conventional
converters and Sparse converters. In Conventional circuits the
numbers of switching devices are sufficient enough to achieve
5
independent control of both the converter and the three-phase
inverter. In sparse converters the number of switching devices are not
sufficient enough to achieve this independent control, thus the
converter and inverter control actions are dependent on each other. As
the number of switching devices are reduced the name sparse
converters has been given.
Main advantages of the four-switch converter compared to the
conventional six-switch converter can be summarized as
bellow ;
The number of the power semiconductor switches and the fly-wheel diodes are
reduced, resulting in cost and space savings. Besides, the control and drive
circuits are reduced which itself brings more savings.Due to a reduced number of
switches, the conduction and switching losses in the semiconductor devices will
be reduced.
Eliminating some semiconductor devices from the topology, directly leads to
more reliability.
DC link voltage is as twice as a six-switch converter. Although it is an advantage
in the rectifier operation mode, but it may not be desired in some inverter
applications.
This topology also has some drawbacks;
The third phase current flows through the DC link capacitors. So they are
exposed to low frequency harmonics which calls for bigger values for the DC link
capacitors.
A controller is needed to balance the capacitors voltages. It is proved that the
balanced voltages can be readily achieved by a simple proportional controller.
6
Since the four-switch converter does not eliminate the third-order harmonics
automatically, so a bigger value for switching frequency is expected.
Literature survey:
1. M.B.R. Correa, C.B. Jacobina, E.R.C. Silva, A.M.N. Lima: A General PWM
Strategy for Four-switch Three-phase Inverters, IEEE Transactions on
Power Electronics, Vol. 21, No. 6, Nov. 2006, pp. 1618 – 1627.
This paper presents a method to generate PWM signals for control of
four-switch three-phase inverters. With the proposed approach, it was
possible to study several PWM schemes using three or four vectors to
synthesize the desired output voltage during the switching period. The
scalar version of the proposed modulation technique can be
implemented by software and may be easily included in drive software
with a negligible increase in the computational effort. The effects of
capacitor unbalance have been evaluated, and compensation
procedures have been proposed. The THD analysis shows that the
PWM pattern based on three vectors, in which two are small, presents
the lowest harmonic distortion. However, the common-mode voltage
analysis points out that use of the two greatest vectors, , is more 7
adequate for common-mode voltage reduction. The paper also
presented suitable PWM strategies to be applied when the motor
windings are delta connected.
2. M.N. Uddin, T.S. Radwan, M.A. Rahman: Fuzzy-logic-controller-based
Cost- effective Four-switch Three-phase Inverter-fed IPM Synchronous
Motor Drive System, IEEE Transaction on Industry Application, Vol. 42,
No.1, Jan/Feb. 2006, pp. 21 – 30.
A cost-effective 4S3Ph-inverter-fed IPMSM drive incorporating an FLC
has been developed, simulated, and successfully implemented in real
time using the DSP TI TMS320C31 for a prototype 1-hp motor. The
proposed 4S3Ph-inverter-based drive reduces the cost of the inverter,
the switching losses, and the complexity of the control algorithms as
well as interface circuits as compared to the conventional 6S3P-
inverter-based drive. The vector control scheme has been incorporated
in the integrated drive system to achieve high performance. The
incorporation of FLC as a speed controller enhances the robustness of
the drive. In order to verify the robustness of the proposed approach,
the performances of the proposed FLC-based 4S3Phinverter- fed IPMSM
drive have been investigated both theoretically and experimentally at
different operating conditions. A comparison of performances for the
proposed 4S3Ph-inverterfed IPM motor drive with a conventional
6S3Ph-inverter-fed drive has also been made in terms of THD of the
stator current and speed response under identical operating
conditions. The proposed 4S3Ph-inverter-fed IPMSM drive has been
found robust and acceptable for high-performance industrial variable
speed- drive applications considering its cost reduction and other
inherent advantageous features.
8
3. F. Blaabjerg, D.O. Neacsu, J.K. Pedersen: Adaptive SVM to Compensate
DC-link Voltage Ripple for Four-switch Three-phase Voltage-source
Inverters, IEEE Transactions on Power Electronics, Vol. 14, No. 4, July 1999,
pp.743 – 752.
This paper introduces a new adaptive SVM approach for compensating the dc-link ripple
in a B4 inverter. To achieve this goal, both dc-link voltages are sensed and the equations
corresponding to the time portions allocated to the switching vectors by the SVM method
are modified accordingly. The theory, design, and performance of this PWM method are
presented, and the method effectiveness is demonstrated by extensive simulations and
experiments. The quality of the inverter output waveforms is demonstrated to be the same
as for the ripple-free case. Furthermore, this adaptive SVM method allows reducing the
size of the dc-filter capacitors. However, assuming the presence of the dc-ripple leads to a
more reduced value of the maximum rms phase voltage and to additional stress of the
power devices and the induction machine which have to be weighted against the
advantages.
4. C.T. Lin, C.W. Hung, C.W. Liu: Position Sensorless Control for Four-switch
Three-phase Brushless DC Motor Drives, IEEE Transactions on Power
Electronics, Vol. 23, No. 1, Jan. 2008, pp. 438 – 444.
This paper has presented a novel FPGA-based sensorless control
scheme for four-switch three-phase brushless dc motor drives. In the
scheme, a novel asymmetric PWM scheme using six commutation
modes in the FSTP inverter is proposed. The position information is
estimated from the crossings of voltage waveforms in floating phases,
and a low cost FPGA is utilized to implement the algorithm. Because
the stator current waveforms of the FSTP inverter using this novel
voltage PWM scheme are rectangular, the motor will operate smoothly
9
and the torque ripple will be at the same level. However, the two
estimated commutations maybe cause commutation torque ripple. The
experimental results show that the scheme works very well. With the
developed control scheme and the lowest cost implementation, the
proposed scheme is suitable for commercial applications.
5. J. Kim, J. Hong, K. Nam: A Current Distortion Compensation Scheme for
Four-switch Inverters, IEEE Transactions on Power Electronics, Vol. 24, No.
4, April 2009, pp. 1032 – 1040.
It was investigated that the source impedance unbalance and the
center tap voltage fluctuation were the major reasons for the phase
current distortion of the four-switch inverters. Both of them originated
from the limited (finite) capacity of dc-link capacitors. Hence, the
motor phase current distortion becomes ignificant as the frequency
decreases, load increases, and the capacitance decreases. The
corresponding errors were derived as the functions of the capacitive
variable , and a compensation method was proposed based on . The
effectiveness of the proposed method was supported by the simulation
and experimental results. The proposed method, just requiring
measurements of -phase current, can be easily implemented.Thus, the
proposed method is believed to be a viable tool for four-switch
inverters.
6. Stanislav Bartos, Ivo Dolezel, Jakub Necesany, Jiri Skramlik and Viktor
Valouch Institute of Thermomechanics ASCR, Dolejskova, Electromagnetic
Interferences in Inverter-Fed Induction Motor Drives, Institute of
Thermomechanics ASCR, olejskova 5, 182 00 Praha 8, Czech Republic.
The equivalent models of the feeding cable as well as the IM suitable
for the determination of stray current disturbances in the common and
10
differential modes have been suggested. The frequency characteristics
of selected parts of the system and their contributions to the resultant
harmonic spectra have been evaluated as well. The responses
obtained on this model well correspond with the responses captured on
the real drive system. This holds even at the very beginning of the
transients, where the variables variables (mainly currents) are
characterized by steep changes (peaks) and high frequencies. As for
the IGCT inverters, it has to be expected that these inverters may
produce similar voltage waves traveling along the cables connecting
the inverters and ac motors and resulting phenomena as those
produced by the IGBT inverters, although IGCT total switching times
are substantially longer. The paper summarizes also the experience
acquired during laboratory experimental operation of the IGBT and
IGCT inverter feeding a 3-phase induction machine (IM) as well as
practical knowledge gained from the employment of these switching
devices in vehicles of city mass transportation.
7. M. Nasir Uddin, T. S. Radwan, and M. A. Rahman, Performance Analysis of
a Cost Effective 4-Switch 3-Phase Inverter Fed IM Drive, IRANIAN
JOURNAL OF ELECTRICAL AND COMPUTER ENGINEERING, VOL.
5, NO. 2, SUMMER-FALL 2006 1682-0053/06$10 2006 JD, 97
A cost effective 4S3P inverter fed IM drive has been simulated and successfully
implemented in real-time using TI TMS320C31 DSP for a prototype 1 hp induction
motor. The proposed control approach reduces the cost of the inverter, the switching
losses, and the complexity of the control algorithms and interface circuits as compared to
the conventional 6S3P inverter based drive. However, the proposed inverter based drive
suffers from slight unbalance in the phase currents which cause relatively higher speed
vibrations as compared to the conventional 6S3P inverter fed drive. The vector control
scheme is incorporated in the integrated drive system to achieve high performance. The
performance of the proposed drive is investigated both theoretically and experimentally
at different operating conditions. A performance comparison of the proposed 4S3P
11
inverter fed drive with a conventional 6S3P inverter fed drive is also made in terms of
total harmonic distortion (THD) of the stator current and speed response. The proposed
4S3P inverter fed IM drive is found acceptable for high performance industrial variable
speed drive applications considering its cost reduction and other advantageous features.
Proposed Topology
12
In the simulation and experimental work, the single phase half bridge rectifier converts
AC power to DC. The DC power is fed to FSTPI. The FSTPI converts the DC power to
controlled 3-phase AC power. The 3-phase induction motor is driven by the FSTPI.
Microcontroller is used to generate the controlled PWM pulse for FSTPI. The controlled
PWM pulses of microcontroller are fed to the gate of MOSFETs of FSTPI through the
driver circuit to drive the IM.
Fig1: circuit diagram of four switch three phase inverter
Principle of FSTPI operation
The power circuit of the FSTPI fed IM drive is shown in Fig. 1. The circuit consists of 4-
switches S1 , S2 , S3 and S4 and split capacitors C1 and C2 . The 3-phase AC input,
which is of fixed frequency, is rectified by the rectifier switches. The power circuit is the
three-phase four-switch inverter. Two phases ‘a’ and ‘b’ are connected to the two legs of
the inverter, while the third phase ‘c’ is connected to the center point of the dc-link
capacitors, C1 and C2 .The 4 power switches are denoted by the binary variables 1 S to
4 S , wherethe binary ‘1’ corresponds to an ON state and the binary ‘0’ corresponds to an
OFF state. The states of the upper switches ( S1 , S2 ) and lower switches ( S3 , S4 ) of
a leg are complementary that is S3 =1− S1 and S4 =1− S2 . T he terminal voltages Vas
13
,Vbs and Vcs of a 3-phase Y-connected Induction Motor can be expressed as the function
of the states of the upper switches as follows:
Since, there is no control on the third phase, the middle point of the DC
link (point C) is taken as the reference, so:
where Vas , Vbs , Vcs are the inverter output voltages,V c is the voltage across the
dc link capacitors, Vdc is the voltage across the capacitors C1 and C2 (V c =V dc / 2 ).
In matrix form the above equations can be written as:
14
Block diagram of FSTPI fed closed loop induction motor drive:
15
The block diagram of the proposed FSTPI fed induction motor drive system is shown in
figure 2.
The drive system consists of:
Three phase AC supply,
Three-phase diode bridge rectifier,
Three-phase four switches Inverter (FSTPI),
3-phase induction motor.
The controlled equipments are:
Control logic,
Processor board.
The standard AC supply is converted to a DC voltage by a three-phase diode bridge
rectifier. A voltage source FSTPI is used to convert the DC voltage to a variable AC
voltage. The output of the FSTPI is fed to the three-phase induction motor. PC is loaded
with software and code composer software. The software consists of several external
modules used for different engineering applications. The values of each block are
adjusted according to the need of drive system. codes are generated and these codes are
targeted (loaded) to the processor. The processor generates the required PWM pulses
according to the user’s setting blocks in PC. The sensor is connected at the shaft of the
motor to sense the actual speed of the induction motor. The sensor output is fed to the
processor through the ADC of processor. The processor compares the reference speed
(set speed) with actual speed through software loaded. The generated error signal is fed
to the PI controller in the processor. Based on the output of PI controller, the processor
generates the required controlled PWM pulses for FSTPI to control the speed of the
induction motor.
16
Limitations of FSTPI:
Due to the inherent voltage vector limitation in the four-switch inverter, three-phase 120˚
balanced current can only be obtained by using 60˚phase shifted PWM control strategy.
In order to properly utilize the four-switch inverter topology in a certain application, it is
very important to understand its operational limitations. The main limitations are lower
voltage utilization and higher harmonic components. Consequently, it can result in an
increased harmonic copper losses and torque pulsations. Therefore, the four-switch
inverter cannot be an alternative to the six-switch inverter configuration in all application
areas, but can be a good choice in middle power range application, in which a certain
harmonic level can be tolerated. For this circuit to be more effectively utilized advanced
PWM control strategies should be developed for wide application in industry.
Applying the component minimization concept of the four switch inverter to the
conventional three-phase to three-phase PWM converter system, we can reduce the
number of switches from the conventional configuration and come up with the eight
switch based configuration.
The desirable functions of an active power factor correction scheme are line voltage
rectification, bus voltage regulation and line current wave shaping. To perform these
tasks an additional circuitry, based on a dc-dc converter, is added to the front-end
rectifier. Among a number of dc-dc topologies proposed in the literature, the use of a
boost converter has been considered very appropriate for many applications due to the
following reasons.
1) The dc bus voltage is higher than the conventional diode bridge rectified ac
voltage. This is very convenient to increase the range of operation of single-phase
to three phase motor drive inverters.
2) It has an inductor in the input and a capacitor at the output, which is very
convenient for filtering.
Figure 1.3 shows the conventional active power factor correction scheme based on the
boost converter. The input current shaping is done by the boost action of the inductor and
the switch‘s’.
17
For efficient operation of the above scheme the circuit needs to be operating at a high
switching frequency in tens of kHz range. At higher switching frequencies the switching
losses increase, and the cost of high voltage diodes with fast reverse recovery
characteristics prove to be costly.
This configuration does not provide bi-directional power flow between the dc bus and the
ac mains, which is a very desirable feature for ac motor drives. Moreover, though the
boosted dc bus improves the drive operating range, when compared to the conventional
system, still there is a limitation for the system speed range. Several single-phase to
three-phase topologies were proposed in [7] with bidirectional power flow and input
current shaping capabilities and with reduced component count.
18
References
[1] J. Kim, J. Hong, K. Nam: A Current Distortion Compensation Scheme for Four-
switch
Inverters, IEEE Transactions on Power Electronics, Vol. 24, No. 4, April 2009, pp. 1032
– 1040.
[2] M.B.R. Correa, C.B. Jacobina, E.R.C. Silva, A.M.N. Lima: A General PWM Strategy
for
Four-switch Three-phase Inverters, IEEE Transactions on Power Electronics, Vol. 21,
No. 6,
Nov. 2006, pp. 1618 – 1627.
[3] M.N. Uddin, T.S. Radwan, M.A. Rahman: Fuzzy-logic-controller-based Cost-
effective
Four-switch Three-phase Inverter-fed IPM Synchronous Motor Drive System, IEEE
Transaction on Industry Application, Vol. 42, No.1, Jan/Feb. 2006, pp. 21 – 30.
[4] C.T. Lin, C.W. Hung, C.W. Liu: Position Sensorless Control for Four-switch Three-
phase
Brushless DC Motor Drives, IEEE Transactions on Power Electronics, Vol. 23, No. 1,
Jan.
2008, pp. 438 – 444.
F. Blaabjerg, D.O. Neacsu, J.K. Pedersen: Adaptive SVM to Compensate DC-link
Voltage
Ripple for Four-switch Three-phase Voltage-source Inverters, IEEE Transactions on
Power
Electronics, Vol. 14, No. 4, July 1999, pp.743 – 752.
[6] Microchip Technology, 2001, PIC16F877A Data sheet, www.microchip.com.
[7] M. Vasudevan, R. Arumugam, S. Paramasivam: High-performance Adaptive
Intelligent
Direct Torque Control Schemes for Induction Motor Drives, Serbian Journal of Electrical
Engineering, Vol. 2, No. 1, May 2005, pp.93 – 116.
19
[8] M. Bounadja, A. Mellakhi, B. Belmadani: A High Performance PWM Inverter
Voltage-fed
Induction Machines Drive with an Alternative Strategy for Speed Control, Serbian
Journal
of Electrical Engineering, Vol. 4, No. 1, June 2007, pp.35 – 49.
[9] K. Rathnakannan, V. Ranjan: The Modeling and the Analysis of Control Logic for a
Digital
PWM Controller based on a Nano Electronic Single Electronic Transistor, Serbian
Journal
of Electrical Engineering Vol. 5, No. 2, Nov. 2008, 285 – 304.
[10] MATLAB, Simulink User Guide, Math Works Inc., 2007
20