Advanced Surgical kitwall chart

Advanced Surgical kitContent:

1

MP-GW001 Rev. 4

MT-LMK13Long motor key adapter 0.05”

Advanced Surgical kit with external irrigation drills includes:

Option 1 (MK-EI35)

Option 2 (MK-IR35)

Option 3 (MK-0035)

Advanced Surgical kit with internal irrigation drills includes:

Advanced Surgical kit supplied without drills.

Marking drill 1.90mm external irrigationMT-TDN19

Pilot drill 2mm external irrigationMT-TDN20

Twist drill 2.80mm external irrigationMT-TDN28

Twist drill 3.20mm external irrigationMT-TDN32

Twist drill 3.80mm external irrigationMT-TDN38

Twist drill 4.50mm external irrigationMT-TDN45

Twist drill 5mm external irrigationMT-TDN50

Twist drill 5.50mm external irrigationMT-TDN55

Marking drill 1.90mmMT-TD110

Pilot drill 2mmMT-TD200

Twist drill 2.80mmMT-TD280

Twist drill 3.20mmMT-TD320

Twist drill 3.80mmMT-TD380Twist drill 4.50mmMT-TD450

Twist drill 5mmMT-TD500

Twist drill 5.50mmMT-TD550

MT-BT032Body try in 3.20mm

MT-BT045Body try in 4.50mm

MT-BT050Body try in 5mm

MT-BT055Body try in 5.50mm

MT-SMK136

Short motor key adapter 0.05”

2

MT-DE001Drill extender

MT-RI030Ratchet wrench

11

MT-HHK24Hand key for int. hex. connection

Countersink for wide platform implant system

MT-GDN50

10

Countersink for standard platform implant system

MT-GDN33

MT-BT020Body try in 2mm

MT-BT028Body try in 2.80mm

MT-BT038Body try in 3.80mm

3

MT-PP001Parallel pin

5

MT-HHR07Short hand screwdriver for 0.05” hex.

MT-HHR13Long hand screwdriver for 0.05” hex.

MT-HW001Hand wrench

7

MT-MMH10Short motor adapter for int. hex. connection

9

MT-MMH20Long motor adapter for int. hex. connection

®

4

MT-DI001Implant Direction Indicator

MT-HMR10Long direct hand and ratchet hex. key

12

1

2

3

4

12

5

6

7

8

9

10

11

MT-MRH20Hex. ratchet long adapter for int. hex. connection

MT-MRH10Hex. ratchet short adapter for int. hex. connection

8

© MIS Corporation. All Rights Reserved.

MIS Implants Technologies Ltd. www.mis-implants.com

®

MIS’s Quality System complies with international quality standards: ISO 13485:2003 - Quality Management System for Medical Devices, ISO 9001: 2008 – Quality Management System and CE Directive for Medical Devices 93/42/EEC. MIS’s products are cleared for marketing in the USA and CE approved.

MT-HHK24

Hand wrench

MT-MMH10

Procedures Procedures

SEVEN Implant

BIOCOM Implant

3.75mm Implant Procedure

®

Batch Code

Catalogue Number

Non sterile

Key to code used:

The devices must be sterilized before use by autoclave, at a temperature of 134ºC (273ºF) at a pressure of ~315 Kpa during 6 minutes.

Manufacturer

0483MIS Implants Technologies GmbHPaulinenstr. 12A, 32427 Minden, GermanyTel: +49 571-972-7690Email: service@mis-implants.de

EC REP

MIS Implants Technologies Ltd.P.O.Box 7, Bar Lev Industrial Park, 20156, ISRAELWebsite: www.mis-implants.com

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80 Ø2.80

200-500

Ø3.30

15-25

Ø3.30

Drill Speed (RPM)

Diameter

(MT-GDN33)Countersink

(MT-GDN33)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

200-500

Ø3.75

15-25

Ø3.75Ø3.20

Drill Speed (RPM)

Diameter

(MT-GDN33)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

200-500

Ø4.20Ø3.80

15-20

Ø4.20

Countersink

4.20mm Implant Procedure 3.30mm Implant Procedure

5mm Implant Procedure

(MT-GDN50)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

15-25

Ø5Ø4.50

400-600

Ø4.50

200-500

Ø5

6mm Implant Procedure 3.75mm Implant Procedure 5mm Implant Procedure

4.20mm Implant Procedure 6mm Implant Procedure

Drill Speed (RPM)

Diameter

(MT-GDN50)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

400-600

Ø4.50

300-500

Ø5

300-500

Ø5.50 Ø5.50

200-500

Ø6

15-25

Ø6

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

15-25

Ø3.75

300-500

Ø2.80Ø3.60

Ø2.80 Ø3.60

200-400

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN33)Countersink

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN50)Countersink

Drill Speed (RPM)

Drill Speed (RPM)

Diameter

Diameter

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80 Ø3.20

400-700

Ø3.30 Ø4.10

200-400

Ø4.20

200-500

Ø4.20

15-25

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN33)Countersink

Ø4.10 Ø 4.90

200-400

Ø5

200-500

Ø5

15-25

Ø3.80

400-600

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

400-600

Ø4.50

300-500

Ø5

200-500

Ø6 Ø6

15-25200-400

Ø 5.10Ø5.90

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN50)Countersink

Procedure recommended by MIS cannot replace the judgment and the experience of the surgeon Procedure recommended by MIS cannot replace the judgment and the experience of the surgeon

Procedures Procedures

SEVEN Implant

BIOCOM Implant

3.75mm Implant Procedure

®

Batch Code

Catalogue Number

Non sterile

Key to code used:

The devices must be sterilized before use by autoclave, at a temperature of 134ºC (273ºF) at a pressure of ~315 Kpa during 6 minutes.

Manufacturer

0483MIS Implants Technologies GmbHPaulinenstr. 12A, 32427 Minden, GermanyTel: +49 571-972-7690Email: service@mis-implants.de

EC REP

MIS Implants Technologies Ltd.P.O.Box 7, Bar Lev Industrial Park, 20156, ISRAELWebsite: www.mis-implants.com

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80 Ø2.80

200-500

Ø3.30

15-25

Ø3.30

Drill Speed (RPM)

Diameter

(MT-GDN33)Countersink

(MT-GDN33)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

200-500

Ø3.75

15-25

Ø3.75Ø3.20

Drill Speed (RPM)

Diameter

(MT-GDN33)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

200-500

Ø4.20Ø3.80

15-20

Ø4.20

4.20mm Implant Procedure 3.30mm Implant Procedure

5mm Implant Procedure

(MT-GDN50)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

15-25

Ø5Ø4.50

400-600

Ø4.50

200-500

Ø5

6mm Implant Procedure 3.75mm Implant Procedure 5mm Implant Procedure

4.20mm Implant Procedure 6mm Implant Procedure

Drill Speed (RPM)

Diameter

(MT-GDN50)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

400-600

Ø4.50

300-500

Ø5

300-500

Ø5.50 Ø5.50

200-500

Ø6

15-25

Ø6

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

15-25

Ø3.75

300-500

Ø2.80Ø3.60

Ø2.80 Ø3.60

200-400

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN33)Countersink

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN50)Countersink

Drill Speed (RPM)

Drill Speed (RPM)

Diameter

Diameter

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80 Ø3.20

400-700

Ø3.30 Ø4.10

200-400

Ø4.20

200-500

Ø4.20

15-25

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN33)Countersink

Ø4.10 Ø 4.90

200-400

Ø5

200-500

Ø5

15-25

Ø3.80

400-600

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

400-600

Ø4.50

300-500

Ø5

200-500

Ø6 Ø6

15-25200-400

Ø 5.10Ø5.90

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN50)Countersink

Procedure recommended by MIS cannot replace the judgment and the experience of the surgeon Procedure recommended by MIS cannot replace the judgment and the experience of the surgeon

Procedures Procedures

SEVEN Implant

BIOCOM Implant

3.75mm Implant Procedure

®

Batch Code

Catalogue Number

Non sterile

Key to code used:

The devices must be sterilized before use by autoclave, at a temperature of 134ºC (273ºF) at a pressure of ~315 Kpa during 6 minutes.

Manufacturer

0483MIS Implants Technologies GmbHPaulinenstr. 12A, 32427 Minden, GermanyTel: +49 571-972-7690Email: service@mis-implants.de

EC REP

MIS Implants Technologies Ltd.P.O.Box 7, Bar Lev Industrial Park, 20156, ISRAELWebsite: www.mis-implants.com

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80 Ø2.80

200-500

Ø3.30

15-25

Ø3.30

Drill Speed (RPM)

Diameter

(MT-GDN33)Countersink

(MT-GDN33)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

200-500

Ø3.75

15-25

Ø3.75Ø3.20

Drill Speed (RPM)

Diameter

(MT-GDN33)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

200-500

Ø4.20Ø3.80

15-20

Ø4.20

4.20mm Implant Procedure 3.30mm Implant Procedure

5mm Implant Procedure

(MT-GDN50)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

15-25

Ø5Ø4.50

400-600

Ø4.50

200-500

Ø5

6mm Implant Procedure 3.75mm Implant Procedure 5mm Implant Procedure

4.20mm Implant Procedure 6mm Implant Procedure

Drill Speed (RPM)

Diameter

(MT-GDN50)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

400-600

Ø4.50

300-500

Ø5

300-500

Ø5.50 Ø5.50

200-500

Ø6

15-25

Ø6

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

15-25

Ø3.75

300-500

Ø2.80Ø3.60

Ø2.80 Ø3.60

200-400

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN33)Countersink

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN50)Countersink

Drill Speed (RPM)

Drill Speed (RPM)

Diameter

Diameter

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80 Ø3.20

400-700

Ø3.30 Ø4.10

200-400

Ø4.20

200-500

Ø4.20

15-25

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN33)Countersink

For bonetype 1&2

For bonetype 3&4

OR

Final drill(MT-GDN50)Countersink

Ø4.10 Ø 4.90

200-400

Ø5

200-500

Ø5

15-25

Ø3.80

400-600

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

400-600

Ø4.50

300-500

Ø5

200-500

Ø6 Ø6

15-25200-400

Ø 5.10Ø5.90Ø5.90

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN50)Countersink

Procedure recommended by MIS cannot replace the judgment and the experience of the surgeon Procedure recommended by MIS cannot replace the judgment and the experience of the surgeon

Procedures Procedures

SEVEN Implant

BIOCOM Implant

3.75mm Implant Procedure

®

Batch Code

Catalogue Number

Non sterile

Key to code used:

The devices must be sterilized before use by autoclave, at a temperature of 134ºC (273ºF) at a pressure of ~315 Kpa during 6 minutes.

Manufacturer

0483MIS Implants Technologies GmbHPaulinenstr. 12A, 32427 Minden, GermanyTel: +49 571-972-7690Email: service@mis-implants.de

EC REP

MIS Implants Technologies Ltd.P.O.Box 7, Bar Lev Industrial Park, 20156, ISRAELWebsite: www.mis-implants.com

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80 Ø2.80

200-500

Ø3.30

15-25

Ø3.30

Drill Speed (RPM)

Diameter

(MT-GDN33)Countersink

(MT-GDN33)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

200-500

Ø3.75

15-25

Ø3.75Ø3.20

Drill Speed (RPM)

Diameter

(MT-GDN33)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

200-500

Ø4.20Ø3.80

15-20

Ø4.20

4.20mm Implant Procedure 3.30mm Implant Procedure

5mm Implant Procedure

(MT-GDN50)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

15-25

Ø5Ø4.50

400-600

Ø4.50

200-500

Ø5

6mm Implant Procedure 3.75mm Implant Procedure 5mm Implant Procedure

4.20mm Implant Procedure 6mm Implant Procedure

Drill Speed (RPM)

Diameter

(MT-GDN50)Countersink

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

400-600

Ø4.50

300-500

Ø5

300-500

Ø5.50 Ø5.50

200-500

Ø6

15-25

Ø6

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

15-25

Ø3.75

300-500

Ø2.80Ø3.60

Ø2.80 Ø3.60

200-400

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN33)Countersink

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN50)Countersink

Drill Speed (RPM)

Drill Speed (RPM)

Diameter

Diameter

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80 Ø3.20

400-700

Ø3.30 Ø4.10

200-400

Ø4.20

200-500

Ø4.20

15-25

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN33)Countersink

Ø4.10 Ø 4.90

200-400

Ø5

200-500

Ø5

15-25

Ø3.80

400-600

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

1200-1500

Ø1.90

900-1200

Ø2 Ø2

500-700

Ø2.80

400-700

Ø3.20

400-600

Ø3.80

400-600

Ø4.50

300-500

Ø5

200-500

Ø6 Ø6

15-25200-400

Ø 5.10Ø5.90

For bonetype 1&2

For bonetype 3&4

Final drill

OR

(MT-GDN50)Countersink

Procedure recommended by MIS cannot replace the judgment and the experience of the surgeon Procedure recommended by MIS cannot replace the judgment and the experience of the surgeon

Advanced Surgical kitwall chart

Advanced Surgical kitContent:

1

MP-GW001 Rev. 4

MT-LMK13Long motor key adapter 0.05”

Advanced Surgical kit with external irrigation drills includes:

Option 1 (MK-EI35)

Option 2 (MK-IR35)

Option 3 (MK-0035)

Advanced Surgical kit with internal irrigation drills includes:

Advanced Surgical kit supplied without drills.

Marking drill 1.90mm external irrigationMT-TDN19

Pilot drill 2mm external irrigationMT-TDN20

Twist drill 2.80mm external irrigationMT-TDN28

Twist drill 3.20mm external irrigationMT-TDN32

Twist drill 3.80mm external irrigationMT-TDN38

Twist drill 4.50mm external irrigationMT-TDN45

Twist drill 5mm external irrigationMT-TDN50

Twist drill 5.50mm external irrigationMT-TDN55

Marking drill 1.90mmMT-TD110

Pilot drill 2mmMT-TD200

Twist drill 2.80mmMT-TD280

Twist drill 3.20mmMT-TD320

Twist drill 3.80mmMT-TD380Twist drill 4.50mmMT-TD450

Twist drill 5mmMT-TD500

Twist drill 5.50mmMT-TD550

MT-BT032Body try in 3.20mm

MT-BT045Body try in 4.50mm

MT-BT050Body try in 5mm

MT-BT055Body try in 5.50mm

MT-SMK136

Short motor key adapter 0.05”

2

MT-DE001Drill extender

MT-RI030Ratchet wrench

11

MT-HHK24Hand key for int. hex. connection

Countersink for wide platform implant system

MT-GDN50

10

Countersink for standard platform implant system

MT-GDN33

MT-BT020Body try in 2mm

MT-BT028Body try in 2.80mm

MT-BT038Body try in 3.80mm

3

MT-PP001Parallel pin

5

MT-HHR07Short hand screwdriver for 0.05” hex.

MT-HHR13Long hand screwdriver for 0.05” hex.

MT-HW001Hand wrench

7

MT-MMH10Short motor adapter for int. hex. connection

9

MT-MMH20Long motor adapter for int. hex. connection

®

4

MT-DI001Implant Direction Indicator

MT-HMR10Long direct hand and ratchet hex. key

12

1

2

3

4

12

5

6

7

8

9

10

11

MT-MRH20Hex. ratchet long adapter for int. hex. connection

MT-MRH10Hex. ratchet short adapter for int. hex. connection

8

© MIS Corporation. All Rights Reserved.

MIS Implants Technologies Ltd. www.mis-implants.com

®

MIS’s Quality System complies with international quality standards: ISO 13485:2003 - Quality Management System for Medical Devices, ISO 9001: 2008 – Quality Management System and CE Directive for Medical Devices 93/42/EEC. MIS’s products are cleared for marketing in the USA and CE approved.

MT-HHK24

Hand wrench

MT-MMH10

Advanced Surgical kitwall chart

Advanced Surgical kitContent:

1

MP-GW001 Rev. 4

MT-LMK13Long motor key adapter 0.05”

Advanced Surgical kit with external irrigation drills includes:

Option 1 (MK-EI35)

Option 2 (MK-IR35)

Option 3 (MK-0035)

Advanced Surgical kit with internal irrigation drills includes:

Advanced Surgical kit supplied without drills.

Marking drill 1.90mm external irrigationMT-TDN19

Pilot drill 2mm external irrigationMT-TDN20

Twist drill 2.80mm external irrigationMT-TDN28

Twist drill 3.20mm external irrigationMT-TDN32

Twist drill 3.80mm external irrigationMT-TDN38

Twist drill 4.50mm external irrigationMT-TDN45

Twist drill 5mm external irrigationMT-TDN50

Twist drill 5.50mm external irrigationMT-TDN55

Marking drill 1.90mmMT-TD110

Pilot drill 2mmMT-TD200

Twist drill 2.80mmMT-TD280

Twist drill 3.20mmMT-TD320

Twist drill 3.80mmMT-TD380Twist drill 4.50mmMT-TD450

Twist drill 5mmMT-TD500

Twist drill 5.50mmMT-TD550

MT-BT032Body try in 3.20mm

MT-BT045Body try in 4.50mm

MT-BT050Body try in 5mm

MT-BT055Body try in 5.50mm

MT-SMK136

Short motor key adapter 0.05”

2

MT-DE001Drill extender

MT-RI030Ratchet wrench

11

MT-HHK24Hand key for int. hex. connection

Countersink for wide platform implant system

MT-GDN50

10

Countersink for standard platform implant system

MT-GDN33

MT-BT020Body try in 2mm

MT-BT028Body try in 2.80mm

MT-BT038Body try in 3.80mm

3

MT-PP001Parallel pin

5

MT-HHR07Short hand screwdriver for 0.05” hex.

MT-HHR13Long hand screwdriver for 0.05” hex.

MT-HW001Hand wrench

7

MT-MMH10Short motor adapter for int. hex. connection

9

MT-MMH20Long motor adapter for int. hex. connection

®

4

MT-DI001Implant Direction Indicator

MT-HMR10Long direct hand and ratchet hex. key

12

1

2

3

4

12

5

6

7

8

9

10

11

MT-MRH20Hex. ratchet long adapter for int. hex. connection

MT-MRH10Hex. ratchet short adapter for int. hex. connection

8

© MIS Corporation. All Rights Reserved.

MIS Implants Technologies Ltd. www.mis-implants.com

®

MIS’s Quality System complies with international quality standards: ISO 13485:2003 - Quality Management System for Medical Devices, ISO 9001: 2008 – Quality Management System and CE Directive for Medical Devices 93/42/EEC. MIS’s products are cleared for marketing in the USA and CE approved.

MT-HHK24

Hand wrench

MT-MMH10

Advanced Surgical kitwall chart

Advanced Surgical kitContent:

1

MP-GW001 Rev. 4

MT-LMK13Long motor key adapter 0.05”

Advanced Surgical kit with external irrigation drills includes:

Option 1 (MK-EI35)

Option 2 (MK-IR35)

Option 3 (MK-0035)

Advanced Surgical kit with internal irrigation drills includes:

Advanced Surgical kit supplied without drills.

Marking drill 1.90mm external irrigationMT-TDN19

Pilot drill 2mm external irrigationMT-TDN20

Twist drill 2.80mm external irrigationMT-TDN28

Twist drill 3.20mm external irrigationMT-TDN32

Twist drill 3.80mm external irrigationMT-TDN38

Twist drill 4.50mm external irrigationMT-TDN45

Twist drill 5mm external irrigationMT-TDN50

Twist drill 5.50mm external irrigationMT-TDN55

Marking drill 1.90mmMT-TD110

Pilot drill 2mmMT-TD200

Twist drill 2.80mmMT-TD280

Twist drill 3.20mmMT-TD320

Twist drill 3.80mmMT-TD380Twist drill 4.50mmMT-TD450

Twist drill 5mmMT-TD500

Twist drill 5.50mmMT-TD550

MT-BT032Body try in 3.20mm

MT-BT045Body try in 4.50mm

MT-BT050Body try in 5mm

MT-BT055Body try in 5.50mm

MT-SMK136

Short motor key adapter 0.05”

2

MT-DE001Drill extender

MT-RI030Ratchet wrench

11

MT-HHK24Hand key for int. hex. connection

Countersink for wide platform implant system

MT-GDN50

10

Countersink for standard platform implant system

MT-GDN33

MT-BT020Body try in 2mm

MT-BT028Body try in 2.80mm

MT-BT038Body try in 3.80mm

3

MT-PP001Parallel pin

5

MT-HHR07Short hand screwdriver for 0.05” hex.

MT-HHR13Long hand screwdriver for 0.05” hex.

MT-HW001Hand wrench

7

MT-MMH10Short motor adapter for int. hex. connection

9

MT-MMH20Long motor adapter for int. hex. connection

®

4

MT-DI001Implant Direction Indicator

MT-HMR10Long direct hand and ratchet hex. key

12

1

2

3

4

12

5

6

7

8

9

10

11

MT-MRH20Hex. ratchet long adapter for int. hex. connection

MT-MRH10Hex. ratchet short adapter for int. hex. connection

8

© MIS Corporation. All Rights Reserved.

MIS Implants Technologies Ltd. www.mis-implants.com

®

MIS’s Quality System complies with international quality standards: ISO 13485:2003 - Quality Management System for Medical Devices, ISO 9001: 2008 – Quality Management System and CE Directive for Medical Devices 93/42/EEC. MIS’s products are cleared for marketing in the USA and CE approved.

MT-HHK24

Hand wrench

MT-MMH10