Post on 12-Oct-2020
transcript
MANUAL
A.E.G.Automatic Electric Gun
TR4 / TR15 / TR16MANUAL
A.E.G.Automatic Electric Gun
TR4 / TR15 / TR16Tel : +1-626-581-0101 Fax : +1-626-581-10111122 Coiner Court City of Industry, CA91748 (U.S.A.)sales101@guay2.com
Los AngelesU.S.A.
TAIWANTel : +886-4-798-9000 Fax : +886-4-798-9900No.999, Zhonghua Rd. Shengang Township, Changhua County 50952, Taiwan (R.O.C.)
Tel : +886-2-2692-2000 Fax : +886-2-2692-400011F-3., No.27, Lane 169, Kangning St. Shijr City, Taipei County 22180, Taiwan (R.O.C.)
sales@guay2.com, b2b@guay2.comsupport@guay2.compr@guay2.com
Taipei
Sales Dept.Technology Dept.
PR Dept.
ChangHua(Head Quarter)
MANUAL
A.E.G.Automatic Electric Gun
TR4 / TR15 / TR16MANUAL
A.E.G.Automatic Electric Gun
TR4 / TR15 / TR16
G2-201211-02-英
TR4 / TR15 / TR16A.E.G. Manual
1 2
Warning Warning
WarningFor more product information
please visit our websitewww.guay2.com
All products employ a high precision 6.04mm barrel. Using 5.95mm BB pellets is highly recommended. Damage to the product due to by faulty BB pellets voids the warranty. Use with caution.The buyer and the user of this product shall adhere to all local laws regulating the usage and the ownership of airsoft guns.
This product is intended for users 18 years or older.Read all instructions before using this product.Adult supervision required.Always wear safety goggles when using this product.Misuse or careless handling of this product may cause injury.May be hazardous up to 50 meters.
Orange tip disclaimer:All G&G Airsoft guns come with a permanent fixed orange tip required by law, which will grant Airsoft legal usage in the United States.If you alter, modify, abuse or remove the orange tip, all warranty coverage will be void.
You may be liable for damaging public, personal property, or for injuring a person or an animal. Always observe good manners and enjoy fun sport shooting.
When you carry the air gun, attach the safety cap, set the selector lever to the safety position, and always put the air gun in a case or bag.
Never direct the muzzle towards a person, animal, or in any direction that may cause harm or damage to a third party.
Make sure to put the barrel and safety cap onto the muzzle except when shooting, to prevent any accidents, discharge of BB's, and also for dust protection purposes. Never pull the trigger while the barrel and safety cap are attached.
Select a safe place for operating the air gun and avoid places where people and cars are around.
Safety procedures:1. Attach the safety cap to the muzzle.2. Set the selector lever to the safety position.3. Remove the magazine.
Looking into the muzzle is extremely dangerous, regardless of having BB's loaded or not. If you get hit in the eye by a BB pellet, worst case scenario, you may lose your eye sight.
Act ivat ing the t r igger carelessly is extremely dangerous. Never put your finger on the trigger unless the safety cap is removed and you are ready to shoot a target.
When shooting the air guns for target practice or in a game situation, you and all participants must wear safety goggles or other eye protective gear. Please pay attention to ricochets and third parties around you.
Always attach the safety cap to the muzzle, remove the battery and store the air gun in a case or bag and at a place that is out of reach of children.
There may be cases where some BB’s remain in the gun after the magazine has been removed. After removal of the magazine, direct the muzzle towards a safe direction and pull the trigger to confirm that there are no BB's remaining in the gun, then attach the safety cap.
Disassembling or modifying the gun may adversely affect the performance and make it dangerous. It would also void all warranty.
TR4 / TR15 / TR16A.E.G. Manual
Contents TR4 Series List
3 4
Contents TR4 Series List
01030405061113181921222526273132333435363738394142
Warning
Contents
TR4 Series List
TR15 Series List
TR16 Series List
Blow Back Pneumatic System
TR16 Series Components
TR15 Series Components
TR4 Series Components
Selector & Safety
Installing the Battery
Sight Adjustment
Charging Handle & Hop-up Adjustment
Movable Parts
Magazine Setting
Firing
Maintenance
Troubleshooting & Disclaimer
Parts List - Common
Parts List - Gear Box
Parts List - Mock Suppressor & Barrel
Parts List - Upper Receiver & Sight
Parts List - Handguard & Rail
Parts List - Stock
Parts List - Grip & Others
[ TR4-18 Light DST ]
[ TR4-18 Light ]
[ TR4-18 DST ]
[ TR4-18 ]
[ TR4 CQB-H ]
[ TR4 CQB-R ]
[ TR4 CQB-S ]
[ TR4 CQB-H DST ]
[ TR4 CQB-R DST ]
[ TR4 CQB-S DST ]
For more product information please visit our websitewww.guay2.com
TR4 Series list
TR4 / TR15 / TR16A.E.G. Manual
TR15 Series List TR16 Series List
5 6
[ TR15 Raider ]
[ TR15 Raider-L ]
For more product information please visit our websitewww.guay2.com
TR15 Series list
[ TR15 Raider-XL ]
[ TR15 Raider DST ]
[ TR15 Raider-L DST ]
[ TR15 Raider-XL DST ]
For more product information please visit our websitewww.guay2.com
TR16 Series list
[ TR16 Carbine ]
[ TR16 Ranger ]
[ TR16 Carbine Light ]
[ TR16 Carbine DST ]
[ TR16 Ranger DST ]
[ TR16 Carbine Light DST ]
TR4 / TR15 / TR16A.E.G. Manual
TR16 Series List TR16 Series List
7 8
For more product information please visit our websitewww.guay2.com
TR16 Series listFor more product information please visit our websitewww.guay2.com
TR16 Series list
[ TR16 CRW ] [ TR16 CRW Cannon DST ]
[ TR16 CRW Cannon ]
[ TR16 CRW Viper DST ]
[ TR16 CRW DST ]
[ TR16 CRW Viper ]
[ TR16 CQW ]
[ TR16 A2 DST ]
[ TR16 A2 ]
[ TR16 A2 Carbine DST ]
[ TR16 CQW DST ]
[ TR16 A2 Carbine ]
TR4 / TR15 / TR16A.E.G. Manual
TR16 Series List TR16 Series List
9 10
For more product information please visit our websitewww.guay2.com
TR16 Series listFor more product information please visit our websitewww.guay2.com
TR16 Series list
[ TR16 R4 Carbine ] [ TR16 R4 DST ]
[ TR16 R4 ]
[ TR16 R4 Commando DST ]
[ TR16 R4 Carbine DST ]
[ TR16 R4 Commando ]
[ TR16 A3 Carbine ][ TR16 R5 DST ]
[ TR16 R5 ]
[ TR16 A3 DST ]
[ TR16 A3 Carbine DST ]
[ TR16 A3 ]
TR4 / TR15 / TR16A.E.G. Manual
Blow Back System Patents
1 1 12
Blow Back Pneumatic System
For more product information please visit our websitewww.guay2.com
G&G awarded New blow back pneumatic system patents all over the world
True to the faith of mimicking real life firearms, G&G is proud to present its new Pneumatic Blow Back system to its line of airsoft guns. Conventional airsoft blow back utilizes tow hook springs to mimic real life bolt actions, which often lead to excess wear, tear, and poor reliability in the gear box. To alleviate the problem of conventional systems, G&G has independently developed the Pneumatic Blow Back system; a piston driven and gas operated mechanism to better mimic real life bolt actions.This new technology utilizes compressed air to move the bolt, which enables the action without adding extra stress to the gear box.This class leading system represents a significant milestone in the airsoft industry.
TR4 / TR15 / TR16A.E.G. Manual
TR16 Series Components TR16 Series Components
13 14
Flash Suppressor
Delta Ring
450 Rounds Magazine
Trigger guard
GripSelector lever
Outer BarrelTR16 Carbine / R4 / R4 Carbine
Outer BarrelTR16 A2 / A3 / R5 / A2 Carbine / A3 Carbine
Handguard (Short)TR16 Carbine / A2 Carbine / A3 Carbine
Handguard (Long)TR16 A2 / A3
Receiver SetTR16 A2 / A2 Carbine
Tactical Sling AttachmentTR16 Carbine / A2 Carbine / R4 Carbine
6-Position Retractable StockTR16 Carbine / A2 Carbine / R4 Carbine
Fixed StockTR16 A2 / A3 /A3 Carbine / R4 / R5
Flash SuppressorDelta Ring
450 Rounds MagazineTrigger Guard
Grip
Selector Lever
Outer BarrelTR16 Carbine Light
Outer BarrelTR16 Ranger
Tactical Sling AttachmentTR16 Carbine / A2 Carbine / R4 Carbine
6-Position Retractable StockTR16 Carbine / A2 Carbine / R4 Carbine
Handguard (Short)TR16 Carbine Light / TR16 Ranger
Detachable Carrying HandleTR16 Carbine Light / TR16 Ranger / A3 / A3 Carbine
TR16 Series ComponentsFor more product information please visit our websitewww.guay2.com
TR16 Series ComponentsFor more product information please visit our websitewww.guay2.com
TR4 / TR15 / TR16A.E.G. Manual
TR16 Series Components TR16 Series Components
1 5 16
TR16 CQW
Trigger
Patriot battery stock for TR16
Tactical gripfor TR16
Ready MagazineTR16 R4 carbine / CRW
Handguard panels
Flash suppressor for SCAR-Type IIPBS mock suppressor for AK
Front sight for TR16 C.Q.W. Rear sight for T418
Front sight for T418
Front sight for T418
Front kit for TR16 CRW Viper
450 rounds magazine
450 rounds magazine
Trigger guard
Trigger guardTactical grip for TR16 series
Selector lever
Selector lever
Rail system (short)TR16 CQW / CRW / Cannon / Viper
Rail system (short)TR16 CQW / CRW / Cannon / Viper
Detachable rear sight
Trigger
Q.D. Sling swivel
Extend battery stock for TR16
Reinforced grip for LR300
TR16 CRW
TR16 CRW Cannon
TR16 CRW Viper
TR16 Series ComponentsFor more product information please visit our website
www.guay2.com
TR16 Series ComponentsFor more product information
please visit our websitewww.guay2.com
TR4 / TR15 / TR16A.E.G. Manual
TR16 Series Components TR15 Series Components
1817
Rear sling swivel
Trigger
Magazine catch button
Forward grip
Rail system (short)TR16 R4 / R4 carbine
Outer BarrelTR15 Raider-L / XL
Rail system (short)TR15 Raider / Raider-L
GripTR15 Raider / Raider-L
Rail system (long)TR15 Raider-XL
GripTR15 Raider-XL
Rail system (long)TR16 R5
Front sling swivel
Front sight
Front sight
Ready-MAGTR16 R4 carbine / CRW
Detachable rear sightTR16 R4 / R4 carbine / R5
TR16 R4 / R4 carbine / R5
Handguard panelsTR16 R4 / R4 carbine / R5
TR16 Series ComponentsFor more product information please visit our websitewww.guay2.com
TR15 Series ComponentsFor more product information please visit our website
www.guay2.com
Selector lever
Trigger guard450 rounds magazine
Extend battery stock
Front sling swivel
Mock flash suppressorDetachable rear sight
TR4 / TR15 / TR16A.E.G. Manual
TR4 Series Components TR4 Series Components
19 20
TR4 CQB H TR4-18
TR4 CQB R TR4 CQB S
LR300 Type flash suppressor
Detachable rear sight
Front sight
Outer barrel
Front gripFront grip
Selector lever
Grip
Trigger guard450 rounds magazine
Assault typeflash suppressor
Handguard panel
Handguard
Sopmod tactical stock
Stock release lever
Trigger
Rear sling swivelRail mount system (SD type)
Stock release lever Rail System
Mock sound suppressor
Q.D. Sling swivel mount
Extend battery stock for TR16
TR4 Series Components TR4 Series ComponentsFor more product information
please visit our websitewww.guay2.com
GripTR4-18 Series
Rear SightTR4-18 Series
Folding Front sightTR4-18 Series
TR4-18 Series
TR4 / TR15 / TR16A.E.G. Manual
Selector & Safety Installing the Battery
2221
Lower the stock plate nail and open the cover. Close the battery cover.
Click
TR16 A2 / A3 / A3 Carbine / R4 / R5For Fixed Stock Version
Always set the safety mode setting immediately after firing.
► Never operate the selector switch while pulling the trigger. Otherwise, malfunctions may occur.► Pulling the trigger with the Selector being set at safe mode may damage the air gun.
Warning
► Use only the G&G battery purchased from your local dealer.
Warning
Automatic firing
Fully Automatic Mode
The gun will fire continuously while the trigger remains pulled.
Single shot
Semi Mode
The gun will fire one shot each time when pulling the trigger.
The trigger cannot be pulled
Safety Setting Mode
When the gun is in storage or not being fired, always set the selector to the Safe position and attach the protective cap on the muzzle.
Pull the delta ring and hold.Remove the lower handguard.
Hold the battery and pull the delta ring.Remove the lower handguard.
Click
TR16 Carbine / A2 Carbine TR4 CQB HFor Handguard Version
Selector & Safety Installing the Battery
Connect the connector until you hear a 'click', then insert the battery into the fixed stock.
Set the battery beside the outer barrel.Connect the battery plug with the connector until you hear a 'click'.
TR4 / TR15 / TR16A.E.G. Manual
Installing the Battery Installing the Battery
2423
TR4 CQB R / TR4 CQB STR15 SeriesTR16 CQW
TR4 CQB R / TR4 CQB STR15 Series TR16 R4 Carbine / CRW
TR16 CRW Cannon / CRW Viper
TR16 CQW
1. Push the stock release lever.2. Pull the stock to the last position.
Insert the battery into the stock. Reinstall the stock.
Turn and take off the battery cover.1. Pull and hold the stock release lever mount.2. Pull out the stock.
For Extended Battery Stock Version
Pull out the connector.
Release the battery stock.
Insert into upper receiver and connect firmlyuntil you hear a 'click'.
1. Insert the battery into the stock.2. Lock the stock.
For Ready Magazine Version
For Patriot Battery Stock Version
Installing the Battery Installing the Battery
For Extended Battery Stock Version
Connect the battery plug into the connector until you hear a 'click'.
Connect the battery plug with the connector until you hear a 'click'.
Connect the battery plug with the connector until you hear a 'click'.
Click
Click
Click Click
2 2
1
2
1
1
► Use only the G&G battery purchased from your local dealer.
Warning
► Use only the G&G battery purchased from your local dealer.
Warning
TR4 / TR15 / TR16A.E.G. Manual
Sight Adjustment Charging Handle &Hop-up Adjustment
2625
Sight Adjustment Charging Handle & Hop-up Adjustment
Front sight adjustment
Precision targeting Up-down adjustment
Windage adjustment knob
LEFT
LEFTLEFT
RIGHTRIGHTRIGHT
RIGHTRIGHTFor left-right adjustment.Turning clockwise :Shifts the pellet hitting point to the right.Turning counterclockwise :Shifts the pellet hitting point to the left.
Turning the windage adjustment dial will move the pellet hitting point to the left or right.
For front sight up-down adjustment.Turning clockwise : Raises the pellet hitting point.Turning counterclockwise : Lowers the pellet hitting point.
Battle sight ( For common shooting )Used for full automatic firing.
Battle sight ( For special shooting )Used for precision firing. Raises the pellet hitting point.
Turning the dial UPwill raise the pellet hitting point.
Turning the dial DOWNwill lower the pellet hitting point.
UP
DOWN
► Make sure not to lose the adjustment tool.
Warning► Be careful not to catch your fingers in the dummy bolt.
Warning
Warning
Hop-up adjustment
1. The Charging handle can be pulled and the bolt will be fastened.2. Pulling the charging handle will take the bolt back and open the port cover.
Turn the hop-up for a desired flight pattern of the BB pellet.The hop-up dial can be turned to a certain degree.Turning it too much will damage the unit.
Open the port cover
Normal Hop
►Too much hop-up ( Return the lever toward Normal ).
Best Direction.
Not enough hop-up ( Move the lever toward HOP ).or Too much hop-up ( Return the lever toward Normal ).
2
1
Never hold the gun sideways as the BB pellets will curve right or left due to the hop-up system.
This function is only for the plastic/blow back version
TR4 / TR15 / TR16A.E.G. Manual
Movable Parts Movable Parts
2827
► Only adjust if the gear noise becomes shrilly. Movable Parts Movable PartsWarning
Depress the Trigger Guard
Depress the trigger guard plunger with a proper tool and open the trigger guard.
Motor Adjustment
The motor adjustable screw is at the bottom of the grip.Use a screwdriver to adjust.
Set the forward grip on the rail. Move the forward grip to adjust position. Fasten the knob.
Forward Grip Setting
Fasten the interface knob. Finish.
Installing the Carrying Handle
Put on the detachable rear sight on the upper receiver.
Fasten the interface knob.
Installing the Rear Sight
Finish.
Connect the detachable carrying handle with the upper receiver.
TR4 / TR15 / TR16A.E.G. Manual
Movable Parts Movable Parts
3029
Movable Parts Movable Parts
Set the forward grip on the rail. Slide in the rail handguard panels. Finish.
Rail Handguard Panels Setting
Put on Q.D.sling swivel mount on the rail.Fasten the screw.
Install the Q.D.sling swivel on the Q.D.slingswivel mount.
Install the Q.D. sling swivel on the sopmodtactical stock.
Q.D. Sling Swivel Setting
Pull the delta ring. Remove the lower handguard. Remove the upper handguard.
Removing the Handguard
Push the release lever to unlock. Pull the stock. Adjust the position of the stock. (6 positions)
Retractable Stock
TR4 / TR15 / TR16A.E.G. Manual
Magazine Setting Firing
323 1
Magazine Setting Firing
Firing
Click
Set the Selector Lever to Semi or Full Auto.
Warning ► Make sure to set the magazine upwards. It is securely installed with you hear a 'click'.► Confirm that the safety lever is set to Safety position and do not place your finger on the trigger.
Warning ► Select a safe place for operating the air gun.► Never put your finger on the bolt when operating the air gun.
Press the magazine release. Pull the magazine out of the receiver.
Magazine Setting To Release the Magazine
Open the magazine cover.Load G&G 5.95mm BB pellets into the magazine.The magazine is capable ofholding approximately 450 pellets.
Magazine Setting
ClickCautions On Motor & Battery
After Operation
Charge the battery if the firing cycle becomes slow.Stop using the air gun for 5-10 minutes after firing around 500 rounds in order to ensure a longer life of the motor and battery.
Remove the magazine and fire at a safe direction for 2-3 seconds. Push the forward assist knob to release the spring and have the selector set into safety mode. Make sure that the barrel is empty.
Always disconnect the battery and attach the protective cap whenever you do not operate the air gun.
Press
After the BB pellets have been loaded, close the cover and turn the gear on the bottom until the sound changes.
Insert the magazine into the body until you hear a 'click'.
Make sure to install the magazine upwards and into the body.It is installed properly when you hear a 'click'.
Remove the protective cap only when you are ready to fire the gun.
2.
1.
1.2.
TR4 / TR15 / TR16A.E.G. Manual
Maintenance Troubleshooting
& Disclaimer
3433
Maintenance Troubleshooting
DisclaimerAll products in this manual are imitation firearms and are not intended nor represented to be comparable in design, appearance, or function to any actural firearm offered by other manufacturers.Product names are trademarks of G&G, which has no affiliation to, and is not associated, or sponsored by any manufacturer of actual or imitation firearms. Products may vary form those pictured.
Accessories pictured are not always included with product.Adult supervision required for users under 18 years of age.The purchaser and user should conform to all laws governing the ownership of airsoft guns.
No operation at all
Although motor is revolving, no pellet can be fired
Impossible full-auto operation(automatic firing)
Shooting distance becomes shorter
Too loud operating noise
Pellets being fallen out from barrel end
If gun gets wet
SYMPTOM POTENTIAL CORRECTIVE
Stop operation immediately, disconnect the battery, wipe off water from inside the main body and the battery. After the gun is completely dry, carry out trial firing. If the unit is not operational, please contact your local dealer for repair.
Selector lever is set to safety.Battery is not charged.Battery connector is disconnected.The and of battery connector is reversed.Expired motor life (50,000 to 60,000 rounds) or poor electrical connection.Pellets are clogged inside the magazine.
Pellets are clogged in the chamber.Faulty gear.Insufficient battery power.Faulty pellet feed of magazine.Poor electrical connection.Damaged or worn chamber set.Damaged or worn piston set (O-ring,piston spring)Something is jammed in the inner barrelFaulty BB pellets (too small or heavy)Shortage of silicone oilGear problem caused by too many blank firingWorn or damaged gearGear problem caused by too many blank firingDamaged or worn chamber set.No hop setting.Faulty BB Pellets (too small or heavy)
Set the selector lever to Semi or Full Auto.Charge the battery.Connect the connector.Switch the batteries to the correct position.Replace the dead motor (can be purchased from local dealer or directly from G&G). Check and repair the contacts.Insert the charging rod into the magazine and move up and down a few times to remove clogged pellets.Remove clogged pellets using the cleaning rod.Purchase the replacement gear from your dealer or G&G and repair.Charge the battery.Repair clogging of the magazine.Consult your dealer or G&G for overhaul maintenance or repair.
Replace the replacement parts (purchase from your dealer or G&G)
Use the cleaning rod and clean the inner barrel.Use the genuine G&G Pellets.Place a few drops of silicone oil onto the upper chamber.
Consult your dealer or G&G for overhaul maintenance, part replacement (gear,etc.) or repair.
Turn the hop adjustment lever toward Hop.Use the G&G Pellets.
1. Place a few drops of silicone oil or teflon oil into the pellet entrance. After inserting BB pellets into the magazine, fire the gun for up to 200~300 pellets.2. To complete the cleaning, use the cleaning rod ( with cotton ) to remove excess oil.
Maintenance When Pellet Speed Becomes Low
Removing Clogged Pellets
Warning
► Do not jam the cleaning rod into the barrel by force.►
► Make sure no dirt gets into the chamber to avoid clogging of pellets.► Hop-up may be unstable for 200 to 300 rounds after using silicone oil. This is the normal operation of the gun.► Never use CRC-556, WD40, or other corrosive lubricants.
Warning
1. Return the hop-up dial to the Normal position and insert the cleaning rod from the lead edge of the barrel.2. To remove clogged BB’s, carefully insert the cleaning rod inside with the flat tip facing down as shown below.
Should the BB’s remains inside the barrel, point the gun towards a safe direction and discharge any loosened BB’s in semi-automatic mode.
TR4 / TR15 / TR16A.E.G. Manual
Parts List - Common Parts List - Gear Box
3635
TR16 - 01
TR16 - 02
TR16 - 04
TR16 - 03
TR16 - 07 TR16 - 0
8TR16 - 0
9
TR16 - 21
TR16 - 19
TR16 - 18
TR16 - 17
TR16 - 20
TR16 - 10
TR16 - 12
TR16 - 13
TR16 - 14
TR16 - 11
TR16 - 06
TR16 - 05
TR16 - 16
TR16 - 15
Charging Handle
Port Cover Set
Magazine Catch Set
Selector Plate
Assist Knob Set
Selector Lever Set
Bolt Catch Set
Lower Receiver Set
Hop-Up Set
Hop-Up Rubber Set
Piston Rod
Front Frame Lock Pin Set
Trigger Guard Set
Rear Frame Lock Pin Set
Magazine
Motor Set
TR16-01
TR16-02
TR16-03
TR16-04
TR16-05
TR16-06
TR16-07
TR16-08
TR16-09
TR16-10
TR16-11
TR16-12
TR16-13
TR16-14
TR16-15
TR16-16
Common Parts for TR16 / TR15 / TR4
Non-Blowback for TR16 A2 / A2 Carbine
Blowback for TR16 / TR15 / TR4
TR16-17 Gear Box Set
Blowback Gear Box Set
Charging Upper Cover
Charging Plate
Blowback Piston Set
TR16-18
TR16-19
TR16-20
TR16-21
► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com
Common Parts► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com
Gear Box Set
TR4 / TR15 / TR16A.E.G. ManualParts List -
Mock Suppressor & Barrel Parts List -
Upper Receiver & Sight
3837
TR16 - 31
TR16 - 32
TR16 - 33
TR16 - 34
TR16 - 35
TR16 - 36
TR16 - 37
TR16 - 28
TR16 - 25
TR16 - 24
TR16 - 22
TR16 - 38
TR16 - 39
TR16 - 40
TR16 - 41
TR16 - 42
TR16 - 48
TR16 - 43
TR16 - 46
TR16 - 44
TR16 - 45
TR16 - 47
TR16 - 23TR16 - 3
0
TR16 - 26
TR16 - 29
TR16 - 27
► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com
Mock Suppressor & Barrel ► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com
Upper Receiver & Sight
Mock Suppressor
Mock Suppressor (CRW / CQW / TR4-18)
Mock Suppressor (TR4-18 Light)
Mock Suppressor (CQB-S)
Mock Suppressor (CQB-R/H)
Mock Suppressor (CRW Cannon)
Mock Suppressor (CRW Viper)
Inner Barrel (Different Lengths)
Outer Barrel (CRW / CQW / CRW Cannon)
Outer Barrel (Carbine Light / CQB-R/H / Raider)
Outer Barrel (Ranger)
Outer Barrel
Outer Barrel (A2 / A3 / R5)
Outer Barrel (A2 Carbine / A3 Carbine)
Outer Barrel (TR4-18 Series)
Outer Barrel Extender (TR4-18)
Front Sight
Front Sight (CRW / Viper / Canoon / TR4-18 Light)
Front Sight (CQW)
Front Sight (TR4-18)
Front Sight Mount (TR4-18 Series)
Detachable Carrying Handle
Upper Receiver (A2 / A2 Carbine)
Upper Receiver
Rear Sight (with TR16-38,39)
Rear Sight
Rear Sight (CRW Viper / Cannon)
TR16-22
TR16-23
TR16-24
TR16-25
TR16-26
TR16-27
TR16-28
TR16-29
TR16-30
TR16-31
TR16-32
TR16-33
TR16-34
TR16-35
TR16-36
TR16-37
TR16-38
TR16-39
TR16-40
TR16-41
TR16-42
TR16-43
TR16-44
TR16-45
TR16-46
TR16-47
TR16-48
TR4 / TR15 / TR16A.E.G. ManualParts List -
Handguard & Rail Parts List -
Handguard & Rail
4039
TR16 - 52
TR16 - 53
TR16 - 51
TR16 - 54
TR16 - 62 TR16 - 5
5
TR16 - 60
TR16 - 59
TR16 - 58
TR16 - 56
TR16 - 57
TR16 - 61
TR16 - 50TR16 - 4
9
Handguard Front Fixed Ring
Handguard Front Fixed Ring(TR16 A2 / A3)
Handguard
Handguard (TR16 A2 / A3)
Rail System Set(TR16 R4 / R4 Carbine /TR4 CQB-R)
Rail System Set (TR16 R5)
Rail System Set (Raider-XL)
Rail System Set
Rail System Set (TR4 CQB-S)
Rail System Set(CQW / CRW / Viper / Cannon)
Rail System Set (TR4-18 Series)
Rail System Rear Fixed Set (with No. TR16-50, 51)
Delta Ring (with No. TR16-52,53)
Delta Ring
TR16-49
TR16-50
TR16-51
TR16-52
TR16-53
TR16-54
TR16-55
TR16-56
TR16-57
TR16-58
TR16-59
TR16-60
TR16-61
TR16-62
► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com
Handguard & Rail► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com
Handguard & Rail
TR4 / TR15 / TR16A.E.G. Manual
Parts List - Stock Parts List - Grip & Others
424 1
TR16 - 72
TR16 - 69
TR16 - 71
TR16 - 67
TR16 - 65
TR16 - 73
TR16 - 75
TR16 - 76
TR16 - 78
TR16 - 74
TR16 - 79
TR16 - 77
TR16 - 64
TR16 - 63
TR16 - 70
TR16 - 66
TR16 - 68
Sling Attachment (CRW Viper / Cannon / Raider / Raider-L/XL)
Sling Attachment
Stock Washer (CRW)
Buffer Tube Set (with No. TR16-64, 65)
Rear Q.D. Sling Swivel Set (CRW)
Patriot Battery Stock Set (CRW Viper / Cannon)
Fixed Stock Set
Retractable Stock Set
Extended Battery Stock Set
Sopmod Tactical Stock Set (CQB-H)
Grip Set (Raider / Raider-L)
Grip Set (CQW)
Grip Set (CRW / Viper / Cannon / Raider-XL / TR4-18)
Grip Set
Ready Magazine Set (CRW / R4 Carbine)
Handguard Panel Set (R5 / CQB-S/R)
Forward Grip (R4 / R4 Carbine / R4 Commando / R5 / CQB-S/R)
TR16-63
TR16-64
TR16-65
TR16-66
TR16-67
TR16-68
TR16-69
TR16-70
TR16-71
TR16-72
TR16-73
TR16-74
TR16-75
TR16-76
TR16-77
TR16-78
TR16-79
► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com
Stock► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com
Grip & Others
Loading BB Pellets Movable Parts - Stock Rear Sight Adjustment
Extra Storage Space Front Sight AdjustmentInstalling the BatteryComponents
INSTRUCTIONMANUAL
1. Pull and hold down the delta ring.2. Remove the lower handguard.
TR4 MOD 0
TR4 MOD 0
TR4 MOD 0 DST
Flash Suppressor
Delta Ring
Handguard Picatinny Rail x 3
Mid-Cap 120R MagazineGrip
Selector Lever
Detachable Front Sight Tactical Sling Attachment
6-Position Retractable Stock
Detachable Rear Sight
Click1
1
4
5
1
2
2
3
2
1
2
Connect the battery with the connector until you hear a 'click', then reinstall the lower handguard.
Press the button then pull out.
1.Press down the button to fold the rear sight.2.Loosen the hex screw before removing the rear sight. Pull the charging handle so the rear sight can be removed.
1.Pull the release lever to adjust the position of the stock. (6 positions)2.Pull the locking lever until it click into place to secure the position of the stock.
Turn the knob counterclockwise to remove the front sight.
1. Open the trap door on the top of the BB loader.
2. Load G&G 5.95mm BB pellets into the Magazine style BB Loader.
3.Connect magazine style loader with the 120R Magazine.
4. Slide the retainer to release the injection lever.
5. Press the injection lever to load BBs into the magazine. Continue loading until the magazine is full.
Magazine Style420R BB Loader[ Optional Parts ]Model No. G-08-100-1
LockLock
UnlockUnlock
TR4 / TR15 / TR16A.E.G. Manual
1
2
12
3
1
2
3
1
22
1 23
45 6
7 8
910
1
12
12
4 5 6
2
1
2
13
5
24
3
1
2
2
1
3
4
5
2
1
1
3
2
3
4
2
1
3
49
5
6
7
8
10
11
12
2
1
23
2
3
1
4
2
3
4
56
1
7
2
345
6
1
23
1389
14
4
56
7
1112 8
1
10
3
4
5
1
2
1
3
2
TR4 MOD0 - 01
TR4 MOD0 - 02
TR4 MOD0 - 26
TR4 MOD0 - 28TR4 MOD0 - 2
9
TR4 MOD0 - 30
TR4 MOD0 - 32
TR4 MOD0 - 31
TR4 MOD0 - 27
TR4 MOD0 - 03
TR4 MOD0 - 04
TR4 MOD0 - 05
TR4 MOD0 - 07
TR4 MOD0 - 35
TR4 MOD0 - 08
TR4 MOD0 - 15
TR4 MOD0 - 33
TR4 MOD0 - 25
TR4 MOD0 - 16
TR4 MOD0 - 18
TR4 MOD0 - 19
TR4 MOD0 - 21
TR4 MOD0 - 22
TR4 MOD0 - 24
TR4 MOD0 - 23
TR4 MOD0 - 20
TR4 MOD0 - 17
TR4 MOD0 - 34
TR4 MOD0 - 10
TR4 MOD0 - 11
TR4 MOD0 - 12
TR4 MOD0 - 13
TR4 MOD0 - 14
TR4 MOD0 - 09
TR4 MOD0 - 06
TR4 MOD0 - 01
TR4 MOD0 - 02
TR4 MOD0 - 03
TR4 MOD0 - 04
TR4 MOD0 - 05
TR4 MOD0 - 06
TR4 MOD0 - 07
TR4 MOD0 - 08
TR4 MOD0 - 09
TR4 MOD0 - 10
TR4 MOD0 - 11
TR4 MOD0 - 12
TR4 MOD0 - 13
TR4 MOD0 - 14
TR4 MOD0 - 15
TR4 MOD0 - 16
TR4 MOD0 - 17
TR4 MOD0 - 18
TR4 MOD0 - 19
TR4 MOD0 - 20
TR4 MOD0 - 21
TR4 MOD0 - 22
TR4 MOD0 - 23
TR4 MOD0 - 24
TR4 MOD0 - 25
TR4 MOD0 - 26
TR4 MOD0 - 27
TR4 MOD0 - 28
TR4 MOD0 - 29
TR4 MOD0 - 30
TR4 MOD0 - 31
TR4 MOD0 - 32
TR4 MOD0 - 33
TR4 MOD0 - 34
TR4 MOD0 - 35
Flash Suppressor
Lower Handguard Set
Upper Handguard Set
Outer Barrel Set
Hop Up Set
Delta Ring
Inner Barrel
Upper Receiver Set
Charging Handle Set
Port Cover Set
Front Frame Lock Pin Set
Bolt Catch Set
Selector Lever Set
Magazine Catch Set
Sling Swivel Mount
Stock Tube
Magazine
Lower Receiver Set
Trigger Guard Set
Selector Plate
Rear Frame Lock Pin Set
Grip Set
Motor
Grip Bottom Set
GOS-V2 Stock Set
Gear Box Set
Detachable Front Sight Set
Blow Back Pneumatic Piston Set
Charging Plate Set
Charging Upper Cover Set
Right Selector Cap
Wire
Rear Sight
Handguard Retainer
Imitation Gas Tube
► You may buy all of the groups’ parts from G&G support Dep.► E-Mail: support@guay2com
Parts List
ADDITIONALINSTRUCTIONMANUAL
TR4 MOD 0
G2-201312-03-英