Duplex Stainless Steel Unvented Hot Water Cylinders

INTRODUCINGALBION ULTRASTEEL

Exceptional value for money package!

DESIGNED FOR THE ‘ONE-OFF’ INSTALLER• Market leading brand

• Highest quality materials

• Highest manufacturing quality

• National Technical & Service support

• Fully approved

• 25-year Guarantee

• Competitively priced

PRODUCT RANGE

• Albion Ultrasteel Standard– 6 capacities

• 120 to 300 ltrs– Direct and Indirect

• Albion Ultrasteel Solar– 4 capacities

• 180 to 300 ltrs– Direct and Indirect

QUALITY INSIDE…

Temperature and pressure relief valve operating at 90ºC / 7 bar

Duplex stainless steel cylinder, pressure tested to 15 bar

Totally insulated with environmentally friendly 50mm thick HCFC and

CFC-free foam

22mm cold feed with diffuser

22mm coil connections

Long life Incoloy sheathed immersion

heater

Highly efficient coil-in-coil heat exchanger

22mm hot water outlet

High quality finish

Factory fitted temperature and pressure relief valve

Wide range of models from 120 litres to 300 litresDirect and Indirect versionsSolar models also available

High quality controls

High grade immersion heater(s)

…AND OUT!

HIGH PERFORMANCE ‘COIL-IN-COIL’ HEAT EXCHANGER• High output ratings 16.52kW to

22.38kW

• More efficient transfer of energy

• Fast heat recovery

• Positioned low in the cylinder to achieve more usable hot water• 90-95% compared with 75-80% for

conventional coil

• Cold water inlet diffuser reduces turbulence to minimise mixing of hot and cold water

DUPLEX STAINLESS STEEL CYLINDER • Manufactured from high grade Duplex

stainless steel

• No anode is required

• Superior corrosion resistance – resists

all forms of corrosion including pitting

corrosion, crevice corrosion, uniform

corrosion and stress corrosion cracking

• Post-weld treatment for reliability and

long life

Post-weld treated

No post-weld treatment

INSULATION AND HEAT LOSS

• 50mm thick void free layer of CFC/HCFC-free expanded polyurethane foam lagging

• One-piece insulation cannot separate in transit to ensure effectiveness

• Fully insulated base

• Low standing heat loss

• Environmentally friendly – Ozone Depletion Potential of Zero

– Global Warming Potential of One

• Heat loss figures meet CHeSS Best Practice guidelines for insulation

• Part L 2010 compliant

MINIMAL HEAT LOSS

LONG LIFE IMMERSION HEATERS • Incoloy sheathed for longer

life

• Low watts density for quiet operation

• 3 kW rated– 6kW and 9kW options

available on request

• High quality Titanium immersion heaters available for Commercial / Industrial installations

IMMERSION HEATERS• Albion Ultrasteel units are fitted with immersion heaters as follows:

PRESSURE AND FLOW RATES

• Exceeds performance of comparable vented systems, giving powerful showers & fast filling baths

• Delivers hot water at flow rates up to 50 litres/min.

INSTALLER FRIENDLY DESIGN • Albion Ultrasteel comes as a complete package – just add

pipework!

High flow rate inlet control set

Two port valve Expansion vessel Dual thermostat

Immersion heater Temperature and pressure relief valve

Tundish

ALBION ULTRASTEEL - DIRECT

22mm hot draw-off

22mm secondary return

(not always fitted)

½” F PTRV boss

22mm cold feed with dip pipe to deflector in bottom of cylinder

D F

ALBION ULTRASTEEL - DIRECT

CODE CAPACITY HEIGHT DIAMETER D F WEIGHT WEIGHT (Kg-EMPTY) (Kg-FULL)

REHEAT PERFORMANCE

The reheat performance is measured from 15oC to 65oC after drawing off 70% of the capacity.

ALBION ULTRASTEEL - INDIRECT

22mm hot draw-off

22mm secondary return (not always

fitted)

½” F PTRV boss

22mm cold feed with dip pipe to deflector in bottom of cylinder

second immersion heater (not always fitted)

dry stat pocket

ABCDEF

ALBION ULTRASTEEL - INDIRECT

CODE CAPACITY HEIGHT DIAMETER A B C D E F WEIGHT WEIGHT (Kg-EMPTY) (Kg-FULL)

INDIRECT REHEAT PERFORMANCE

The reheat performance is measured from 15oC to 65oC after drawing off 70% of the capacity.

ALBION ULTRASTEEL SOLAR - DIRECT

All models feature 2 electric immersion heaters for a back up heating – either of them is suitable for use in conjunction with ‘low tariff’ electricity (e.g. Economy 7 or 10).

Coil-in-coil designed to accept input from renewable energy source, such as Kingspan Solar Flat Plate Panel or Thermomax Vacuum Tube Solar Thermal Collectors

TECHNICAL SPECIFICATION – DIRECT SOLAR MODELS

22mm cold feed with dip pipe to deflector in bottom of cylinder

½”F PTRV boss22mm hot draw-off

ABCDEF G

dry stat pockets

22mm secondary return (not always

fitted)

TECHNICAL SPECIFICATION – DIRECT SOLAR MODELS

CODE CAPACITY HEIGHT DIAMETER A B C D E F G WEIGHT WEIGHT (Kg-EMPTY) (Kg-FULL)

ALBION ULTRASTEEL SOLAR - INDIRECT

All models feature electric immersion heater for a back up heating – suitable for use in conjunction with ‘low tariff’ electricity (e.g. Economy 7 or 10)

Upper coil can be connected to traditional source of heat, such as gas, oil or electric boiler

Lower coil is designed to accept input from renewable energy source, such as Kingspan Solar Flat Plate Panel or Thermomax Vacuum Tube Solar Thermal Collectors

TECHNICAL SPECIFICATION – INDIRECT SOLAR MODELS

CODE CAPACITY HEIGHT DIAMETER A B C D E F G H WEIGHT WEIGHT (Kg-EMPTY) (Kg-FULL)

dry stat pockets ½”F PTRV boss22mm hot draw-off

22mm secondary return (not always fitted)

22mm cold feed with dip pipe to deflector in bottom of cylinder

dry stat pocket

ABCEF G HD

COIL SPECIFICATION & WATER CAPACITIES

• 30% of the total volume is dedicated renewable energy capacity

• 70% of the volume can be heated in the traditional way via an upper coil on days when solar energy is not sufficient to heat the full contents of the unit or on days when additional energy is required

DOMESTIC SELECTION GUIDE

COMMERCIAL SELECTION GUIDE

GUARANTEE• Albion Ultrasteel’s stainless steel

vessel features a fully transferable

25-year anti-corrosion guarantee

• The expansion vessel and cold

water controls supplied with the

cylinder carry a 5-year guarantee

• All other components fitted to/or

supplied with the unit carry

a 2-year guarantee

PRODUCT APPROVALS

• BEAB approved immersion heater

• WRAS approved to the Water Regulations

• WRc-NSF approved for Building Regulation G3 & L

• Manufactured in the UK in an BS EN ISO 9001:2008 registered factory

Further Information

www.kingspanenviro.com/albion