Post on 18-May-2018
transcript
PolyKLEAN®
All-Polypropylene Rigid Thermal Bonded Filters
Featuring:
ApplicationsInclude:
Industrial Processes
Coatings
Food & Beverages
Oil & Gas Process Fluids
Chemicals
Electronics
Pharmaceuticals
Consistent filtration
throughout the life of
the filter for superior
quality effluent
Up to ten or more times
the service life of
competitive filters
Low operating pressure
drop achieves the
required flow using
fewer filter elements
®
a 3M company
PolyKLEAN® Filter Cartridges
Advancing depth filtration through technological innovation
PolyKLEAN filters, manufactured using CUNO's rigid extrusion bonded technology, areall-polypropylene depth filter cartridges offering premium features including:
� consistent particle removal efficiencies throughout the filter's life,� increased surface area for extended filter life,� low initial pressure drop for enhanced flow, and� high particle removal efficiencies at high flow rates (flux).
The filter's extended service life results in fewer filter change-outs while its enhancedflow characteristics can typically reduce the number of filters required to achieve a givenflow rate. These combined features of PolyKLEAN filters can
.
PolyKLEAN Filter Construction
The unique PolyKLEAN filter manufacturing process combines the superior processcontrol with the quality assurance enabled by an ISO 9001 certified quality system toprovide consistent product performance. The CUNO exclusive manufacturing processprovides a high degree of fiber-to-fiber thermal bonding, without the use of binders, toproduce a rigid, core-less, filter structure with the following properties:
� does not unload contaminants with increasing differential pressure liketypical meltblown filters,� allows grooves to be machined into the upstream surface, without
tearing or melting the filter structure, providing more than double theeffective surface area, and� exhibits exceptionally low differential pressure for a given filter rating.
Consistent filtration throughout the service life of a depth-style filter dependson how well the filter’s structure tolerates fluctuations in operatingconditions - including contaminant loading and differential pressure.Flexible structures, such as those found in typical meltblown andstring-wound filters, tend to compress and change porosity with increasedpressure, while rigid structures do not (Photo 1). Media compression canresult in short filter life because the pores collapse and ultimately close.
2
Feature Benefit
� Rigid depth filter construction
� Eliminates unloading at high differential pressure� Efficient removal of deformable materials� Consistently superior particle removal throughout filter life
and at high flow rates (flux).
� Enhanced contaminant holding capacity � Fewer filter change outs� Long filter life
� Grooved cartridge with extended surface area � Promotes fuller utilization of the depth-matrix� Long filter life
� All polypropylene construction� Compatibility in a wide range of applications and operating
conditions� No adhesives, binders, surfactants, lubricants
� Materials of construction listed in FDA 21CFR andANSI / NSF Standard 42 and 61 certified
� Complies with regulations for food and beverage contact� Approved for use in potable water applications
� Core-less filter structure � Ease of disposal via incineration or shredding
� Continuous integral length filter element (up to 40") � No bond joints to break� Easy to install
GROOVEDSURFACE
INCREASE INSURFACE AREA
FLOW
Photo 1. - Compressible vs Rigidstructures @ 35 psid
Compressible Rigid
Media compression can also cause the filter to release already held particles. The robust PolyKLEANfilter captures and retains contaminant within its rigid filter matrix, even under increasing differentialpressure. In addition, the unique depth filter structure of the PolyKLEAN filter provides a significantincrease in contaminant holding capacity and provides greater flow capacity at a given pressure.
Unlike soft meltblown and string-wound filters that require core support, the PolyKLEAN filter isself-supporting and is grooved to provide greater than twice the surface area. The increase in surfacearea prevents premature blinding of the outer surface by large particles and gels and promotes fullerutilization of the depth-matrix. The result is significantly longer life than competitive cartridges.
PolyKLEAN Filter Performance
PolyKLEAN filters exhibit superior filtration characteristics. The rigid construction allows forenhanced performance compared to other filter structures with equivalent removal ratings.
Superior Service Life
Extensive testing of PolyKLEAN filters hasdemonstrated an appreciable advantage in servicelife. Graph 1 compares rigid PolyKLEAN filtersto typical meltblown and string-wound filters ofequivalent efficiency. All filters were challengedunder identical conditions. Comparison of testresults, when test filters are subjected to the samecontaminant load up to 20 psid, shows therelative life of the test filters. As depicted,PolyKLEAN filters typically provide nearly twicethe life of its closest competitor, and up to10times or more the life of some competitive filters.
Consistent Removal Efficiency
The rigid PolyKLEAN structure resists deformation, filter by-pass, compression, and particle unloading.This allows PolyKLEAN filters to achieve excellent filtration efficiency up to its recommendedchange-out pressure (35 psid), while typical melt blown and wound structures exhibit significant drops inremoval efficiency at much lower differential pressures (� 10 psid).
To demonstrate the PolyKLEAN filter’sremoval consistency, efficiency at foursampling points (initial, 0.5 psid, 1 psid,and 10 psid) was measured onPolyKLEAN filters and typical melt blownand wound structures. All equivalentlyrated filters were tested under the sameconditions to enable direct comparison.As shown in Graph 2, PolyKLEAN filtersdisplay a stable, consistently highercontaminant removal throughout theduration of the test. Note that the othermelt blown and string wound structuresyield erratic removal and as such can notprovide predictable performance evenunder controlled conditions of uniformcontaminant loading and pressure.
3
Per
cen
t(%
)o
fP
oly
KL
EA
N E
ffic
ien
cy
Differential Pressure (psid)
PolyKLEAN
Meltblown 1
Meltblown 2
Wound Filter0
20
40
60
80
100
Initial 0.5 1 10
Graph 2. - Efficiency Comparison of Filter CartridgesRated at 5 Microns
Per
cen
t(%
)o
fP
oly
KL
EA
N F
ilter
Lif
e PolyKLEAN
Meltblown 1
Meltblown 2
Wound Filter
Meltblown 3
100
50
0
Graph 1 . - Life Comparison of Filters ExhibitingSimilar Efficiency
PolyKLEAN filters are also capable ofdelivering consistent particle removalefficiencies at high fluid flux (flow rate persurface area). This capability isdemonstrated in Graph 3 which shows bothremoval efficiency and differentialpressure results from tests conducted with25u PolyKLEAN cartridges at a fluid fluxof 18 gpm per 10-inch length - six timeshigher than typical design flux forcartridge filters. Because of its rigidstructure and high contaminant holdingcapability, PolyKLEAN cartridges are ableto maintain high particle removalefficiencies throughout the life of the filterat this high flux.
This consistent performance capability at high fluid flux makes PolyKLEAN an effective solution forsystems where smaller housing size is desirable because of physical limitations or budgetary constraints.Utilizing PolyKLEAN cartridges at higher flux can also be beneficial for low contaminant load systems.
Lower Initial Differential Pressure
The unique design and construction of the PolyKLEAN element allows for significantly lower pressuredrop when compared to competitive elements. Graph 4 clearly demonstrates the PolyKLEAN flowadvantage when compared to other 5�m rated competitive meltblown and wound cartridges. For a givendifferential pressure, PolyKLEAN filters yield flows up to ten times that of competitive filters. Whensizing a system for a given process flow rate, this is a significant advantage and translates into lowercapital investment for filter housings and fewer cartridges to purchase. For example, as shown in Table1, in a process with a water flow rate of 180 gpm and a maximum clean pressure drop of 0.5 psid, aPolyKLEAN filter system requires significantly fewer cartridges and smaller filter vessels (compared tocompetitive filters) for greatly reduced capital costs.
Table 1. - Comparison of 5 Micron Filters ina Water System
PolyKLEAN Filters 12 12
Parker Fulflo®Honeycomb™ WoundPolypropylene Filters
29 20
Osmonics Hytrex®
Filters60 30
Pall Claris® Filters 24 16
*Based on the manufacturers literature piece specifications
4
Fulflo and Honeycomb are trademarks of Parker Hannifin Corporation, Hytrex is a trademark of GE Osmonics , and Claris is a trademark of Pall
Corporation
Water Flow (gpm)
Water Flow (lpm)
Dif
fere
nti
alP
ress
ure
(psi
d)
Dif
fere
nti
alP
ress
ure
(bar
)
0 1 2 3 4 5 6 7 8 9 100
0.5
0.1
0.2
0.3
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
GE Osmonics Hytrex filtersParker Fulflo Honeycomb WoundPolyPropylene filtersPall Claris filtersPolyKLEAN filters
10 20 30
Graph 4. - Flow vs. Differential Pressure(see note * in table 1)
Percent of Filter Life
Par
ticle
Rem
oval
Effi
cien
cy(%
)
Particle Removal
Diff
eren
tialP
ress
ure
(psi
d)
Differential Pressure
0 0
10 10
100 20 30 40 50 60 70 80 90 100
20 20
30 30
40 40
50 50
60 60
70 70
80 80
90 90
100 100
Graph 3. - Particle Removal Efficiency at increased flux
PolyKLEAN Filter System Sizing
To size a system of PolyKLEAN filters, flow vs. differential pressure data is provided in Table 2.
Table 2. - PolyKLEAN Filter Specific Pressure Drop (SPD)
�
1 0.073 1.330
5 0.042 0.765
10 0.025 0.455
25 0.015 0.273
50 0.010 0.182
75 0.006 0.109
To calculate filter’s clean pressure drop for Newtonian fluids, use the following formula in conjunctionwith the Specific Pressure Drop Values. The Specific Pressure Drop values may be effectively usedwhen three of the four variables (Viscosity, Flow, Differential Pressure, and Cartridge Grade) are set.Care must be taken when sizing PolyKLEAN filtration systems. Select a filter housing that will accept atleast the required number of 10 inch filter elements, and ensure that the totalsystem flow does not exceed the maximum housing flow rating.
PolyKLEAN Filter Applications
� Plating � Process cooling water� De-salination plants � Parts washing� Pulp & paper � Peroxide� Additives � Mechanical seals
� Resin manufacturers (water & solvent)� Ink
� Trade, architectural paint
� Bottled water � Soft drinks� Ready-To-Drink Beverages � Juice
� Amine & glycol � Process cooling water� Prefiltration in waterflood � Completion fluid
� PE-PP � PVC-VCM� Intermediate grade chemicals � Herbicides, pesticides
� Printed Circuit Boards � Video Dispalys� CMP slurries � Pre-RO� Electronic Capacitors � CD/DVD
� Pre-RO � Rinse water� Bulk pharmaceutical chemicals � Active pharmaceutical ingredients� Particle control in WFI
5
Total systemgpm [lpm]
Viscosity inCp
SPD Valuefrom Table 2
Equivalent number of 10 inchCartridges in housing
=
(
(
( ( (
(
( (psid [mbar]clean
PolyKLEAN Filter Cartridge Specifications
Table 3. - PolyKLEAN Filter Specifications
Construction
Filter Media, End Connector Polypropylene
Gaskets & O-ring Options (see ordering guide) Silicone, Fluorocarbon, EPR, Nitrile, and Polyethylene
Operating Conditions
Maximum Operating Temperature 176° F (80°C)
Maximum Differential Pressure15 psid @ 176°F (1.0 bar @ 80°C)25 psid @ 140°F (1.7 bar @ 60°C)60 psid @ 68°F (4.1 bar @ 20°C)
Recommended Change-out Differential Pressure 35 psid @ 68°F ( 2.4 bar @ 20°C)
Cartridge Dimensions
Inside Diameter (nominal) 1.1" (28 mm)
Outside Diameter (nominal) 2.6" (66 mm)
Length (nominal) see ordering guide 9 34" - 40" (248 - 1016 mm)
Regulatory
PolyKLEAN filters meet the requirements of USP for the Biological Test for Plastics, Class VI-70°C.Materials used in the manufacture of PolyKLEAN filters meet the requirements of USFDA 21 CFR for food and beverage contactPolyKLEAN filters have been certified to ANSI/NSF Standard 42 and 61
Chemical Compatibility
The 100% polypropylene construction provides excellent chemical compatibility in many demanding processfluid applications. Compatibility is influenced by process operating conditions. PolyKLEAN cartridges shouldbe tested under actual conditions to determine compatibility.
Table 4. - Fluid Compatibility
Chemical Temperature Chemical Temperature Chemical Temperature
Acetic Acid 20% 160°F (71°C) Hydrogen Peroxide 100°F (38°C) Sodium Carbonate 160°F (71°C)
Alkanolamines 140°F (60°C) Methyl Ethyl Ketone 70°F (21°C) Sodium Hydroxide 70% 160°F (71°C)
Ammonium Hydroxide 10% 160°F (71°C) Mineral Oil 70°F (21°C) Sulfuric Acid 20% 160°F (71°C)
Bleach 5.5% 120°F (49°C) Nitric Acid 20% 120°F (49°C) Sulfuric Acid 70% 160°F (71°C)
Ethylene Glycol 160°F (71°C) Potassium Hydroxide 140°F (60°C) Urea 160°F (71°C)
Scientific Applications Support Services (SASS)Dedicated technical support teams comprised of CUNO scientists andengineers are available to provide application specific recommendations forthe most effective and economical filtration system. In addition tocomprehensive testing and analyses conducted in advanced laboratories atCUNO Incorporated, the SASS staff can also perform on site-testing atcustomer’s facilities. Contact your CUNO Distributor for more information
Service Worldwide
CUNO is a U.S. based multinational company with distribution and manufacturing sites worldwide. Globalmanufacturing sites together with trained stocking distributors and state-of-the-art laboratory facilities bringquality solutions to challenging filtration applications.
6
CUNO Filter HousingsCUNO manufactures a full line of industry standard filter housings to meet most applicationrequirements. Models are available for both gas and liquid service in a wide range of constructionmaterials, from plastics to ASME Code with 316L stainless steel, to suit a variety of application needs.For more information about CUNO filter housings, consult your local CUNO distributor and ask for theliterature listed below.
� – the ES series filter housing is a durable high volume filter housing constructed from 316Lstainless steel or carbon steel. With a cartridge capacity from 12- to 480- 10 inch filter elements, the ES filterhousing can accommodate a wide range of flow requirements. For more information, ask your local CUNODistributor for brochure LITCHSES1
� – AL and CT filter housings offer a wide range of sizes from one cartridge toeighteen cartridges. For more information, ask your local CUNO Distributor for brochure LITHSAL1 andLITHSCT3.
� – DC and SD filter housings offer a low cost alternative for low volume filtration.Constructed from reliable 304Lstainless steel (Model DC) or 316L stainless steel (Model SD), these housingsare available for a wide range of flow rates and applications. For more information, ask your local CUNODistributor for brochure LITHSDC1 and LITHSSD1.
� . This unique system design provides atotally enclosed system using separate pressure vessel and filter pack to isolate process fluid from housing.This system generally reduces the clean-up costs involved with filter change-out while protecting the workenvironment and the operator from exposure to the process fluid. Ask your local CUNO distributor forbrochure LITCCK001.
7
(LITHSES1)
� Maximum design flexibilityfor a wide variety of systemrequirements
� ASME Code
� Choice of carbon steel, 304Lor 316L stainless steel
� Available in a variety of sizes
� Accepts both single and doubleopen end cartridges
� Available in a varietyof sizes and materials
� Mounting bracketavailable
� Rugged economicaldesign in cast iron andsteel
� Easy assembly
� Enclosed System
� Uses disposable filterpack
� Easy to use - housingclean-up eliminated
� Polyvinylchloride construction
� Available for 2 or 3 highcartridges
� Features a removable cartridgepack for rapid change-out andeasy cleaning
� ASME Code
� Available in a wide varietyof sizes
� 304 stainless steelconstruction
� Available in cast iron andsteel, or 304 stainlesssteel
� Choice of 1 or 2 highcartridge models
� Available in cast iron andsteel, or 304 stainless steel
� Built-in valve for duplexor single operation
� Ideal for high pressureapplications
� Durable steelconstruction
� Lightweight plasticconstruction
� Choice of 1 or 2 highcartridge models
PolyKLEAN Filter Cartridge Ordering GuideCtg. Type Length Grade Material Surface Packaging Ring Support End Modification Gasket/O-Ring
PolyKLEAN- 9 3
4"* - 1�m - Polypropylene - Grooved - Bulk - None - 226 O-Ring & Spear - Silicone
- 10" - 5 �m - 222 O-Ring & Spear - Fluorocarbon
- 19 12"* - 10 �m - 222 O-Ring & Flat Cap - EPR
- 20" - 25 �m - None - Nitrile
- 29 14"* - 50 �m -Polypropylene Core Extender - Polyethylene**
- 30" - 75 �m - Cap without Spring - Clear Silicone
- 39"* - Cap with Spring - None **
- 40"
* Available with N or P end modifications only ** Available with N, P, Q, or R end modifications only
© CUNO Incorporated, 2005 - All Rights Reserved LITCPOLYKLN.1110p
B PC F RQN
Lenntechinfo@lenntech.com Tel. +31-152-610-900www.lenntech.com Fax. +31-152-616-289