INSTALLATION MANUAL

DIGITAL FULL COLOR

MULTIFUNCTIONAL SYSTEM

MX-2640NMX-3140NMX-3640NMODEL

Transit, Installation (using) environment, Note

1. Installing (use) conditions

A. Transportation space

B. Installing space

C. Power source (Capacity, voltage, frequency,

safety, plug)

(1) Power capacity

Current capacity

(2) Power voltage

(3) Power frequency, waveform

(4) Safety

(5) Power plug

D. Floor strength and level

E. Direct rays of the sun, dust, temperature,

humidity, gasses, chemicals, vibration

(1) Temperature and humidity (Environmental

conditions)

No. Content

11-13/16"

(30cm)

11-13/16"

(30cm)

17-23/32"

(45cm)

Operational environment

(2) Contaminates

(3) Direct sunlight

(4) Gases and chemicals

(5) Vibration

F. Note for handling PWB and electronic parts

85%

Humidity RH

60%

20%

G. Note for proper drum, developing, fusing and

transfer unit handling

Drum unit

Transfer unit

Developing unit

Fusing unit

2. Transit and delivery

A. Implements, facility, and manpower

B. Delivery

3. Relationship between the model name and the designation in description of the document

No. Content Method

Model name Designation in description

[2] MX-2640N/3140N/3640N (MAIN UNIT)

1. Unpacking

A. Unpacking

B. Fixing tape and protection material removal

C. Packed items check

No. Name Quantity

1 2

D. Lock release

(1) Tray rotation plate lock release

(2) Scanner (2/3 mirror unit) lock release

2. Installation

A. Developer installation

2

1

3

1

2

B. Set the control level for the reference toner

density

2

1

Color toner cartridge positions

YM

CBK

C. Cleaning

(1) Cleaning of LSU's dust-proof glass and PTC wire

D. Paper feed tray setup

(1) System setting

(2) Tray size setup

E. Specifications setup

Item Description

A

B

SIM No Content

SIM No Content

3. Image quality check

A. Execution items

B. Description

(1) Print engine image distortion adjustment (Manual

adjustment) / OPC drum phase adjustment

(Automatic adjustment) / Color registration

adjustment (Automatic adjustment)

No. Item SIM

EXECUTEAdjustment completed

Abnormal end

Display/

ItemContent Display Default NOTE

(2) Copy color balance and density check

Method 1

1 2 3 4 5 6 7 8 9 10 W

SHARP GRAY CHART

SHARP gray chartPatch 1 is

slightly copied.

Patch 2 is copied.

(Color copy)

1 2 3 4 5 6 7 8 9 10 W

SHARP GRAY CHART

SHARP gray chart

Patch 1 is not copied.

Patch 2 is

slightly copied.

Patch 3 is copied.

( py)

Serviceman chart (Color patch section)

The densities of patches 1 - 6 ofeach color are properly balanced.

Patch 7 is slightlycopied or not copied.

(Color copy)

a. Color copy check items (Check to confirm the following:)

b. Monochrome copy check items (Check to confirm the following:)

Method 2

(3) Printer color balance/density check

Method 1

Method 2

QO PNMLKJIHGFEDCBA

Y

M

C

Bk

Highdensity

1) The max. density section is not blurred.

2) Patch C or D of each of Y, M, C, and BK is very slightly copied.

Lowdensity

CMY

blend

3) Patch for each of Y, M, C, BK

The patch density is identical between patches or not reversed.

The patch density is changed gradually.

PRINTER CALIBRATION

QO PNMLKJIHGFEDCBA

Y

M

C

Bk

1) The max. density section is not blurred.

2) Patch C or D of each of Y, M, C, and BK is very slightly copied.

Low density

CMY

blend

3) Patch for each of Y, M, C, BK

The patch density is identical between patches or not reversed.

The patch density is changed gradually.

High density

(4) Copy/Printer color balance and density adjustment

(Automatic adjustment)

QO PNMLKJIHGFEDCBA

Y

M

C

Bk

Highdensity

Lowdensity

PRINTER CALIBRATION

PRINTER CALIBRATION

1) The max. density section is not blurred.

2) Patch C or D of each of Y, M, C, and BK is very slightly copied.

3) Patch for each of Y, M, C, BK

The patch density is identical between patches or not reversed.

The patch density is changed gradually.

High densityLow density