Post on 15-Nov-2020
transcript
Assembly Instructions
Mobile Laptop Computer Tables
www.smartdesks.com800 770 7042
© 2009 CBT Supply, Inc. dba SMARTdesks. All rights reserved. Quark™ Qstar™ and flipIT® are trademarks of CBT Supply, Inc. flipIT® Laptop Safe Patent Pending.
Tools Required
• Phillips#2Drive• 3/8”HexDrive(optional)• MeasuringTape• BoxCutter• SafetyGlasses
POWER TOOLS ARE DANGEROUS.Reviewthesafetyproceduressuppliedbyyourpowertools’manufacturers.Heedallwarningsforyoursafety’ssake.Alwaysusesafetyglassesandwearproperapparelthatwon’tgetcaughtinmovingparts.CBTSupply,Inc.willnotbeheldliableformisuseoftoolsanddisregardforpowertoolmanufacturer’ssafetyprecautions.
Parts
EnclosedwiththemetalQuark™adjustableheightpedestalboxaretwobagsof8hex/Phillipsdrivemachineboltsand2woodscrews,each.Thehex/Phillipsdriveboltsareforattachingthetopandbottomtothepedestal.Thewoodscrewsareforattachingthesidepanels.
2
Parts and Assemblies
Pedestal Assembly
Side Panels (2)
WireWonder™ Cable Manager
Bottom Plate Top
flipIT® Laptop Safe
Casters: 3 locking, 2 non-locking
The flipIT® Laptop Safe includes a lock assembly with separate installation instructions.
3
Getting Started
Forreference,thecomplet-edQuark™MobileLaptopTablelookslikethis.
Theassemblyareashouldhaveprotectivesurfaceswithoutabrasiveobjectsthatcouldscratchthesurfaces.Keepallsurfacesfreeofsmallmetalscrewsandpartsthatcouldcausedamage.
Install WireWonder™ Cable Manager
TheWireWonder™CableManagerispackagedseparatelywithitsownsetofhex/Phillipsdriveboltsandoptionalwoodscrews.Usethe3hex/Phillipsdriveboltstoinstallintothetappedinsertsprovided.
Anextensionmayberequiredtoinstall.LargeholesinthebottomoftheWireWonder™areprovidedforaccesstotheinstallationbolts.
4
Place Pedestal Assembly on Quark™ Top
Thepedestalcomespre-assembled.Notethepositionofthewiremanage-mentchannelandhalf-mooncutthroughthebottomplate.Makesuretopositionthewiremanagementchanneltothefrontofthetop,soitisonthesamesideastheWireWonder™CableManager.
Theheightadjustmentleverwillbeorientedtotheusersideofthetopwiththelargeconcavecontourandhandles.
Installwitheighthex/Phil-lipsdrivebolts.
5
Install Side Panels
Eachsidepanelhas4pilotholesprovided.Alignthemwiththe4holelocationsonthepedestal.Installusing2woodscrewsforeachpanel,usingadiagonalpatternoftheupperandlowerlocations.
Removethe3hex/Phillipsdriveboltsthatattachthebottomplatetothepedestalassembly.Keeptheboltsreadyforreattachmentafterthebaseplatehasbeeninstalled.
Placethebaseplateonaclean,protectiveworksurface.
Alignthepedestalbaseplatewiththeboltinserts.Notethepositionofthehalf-mooncutoutthatalignswiththewiremanagementchannel.
6
Bolt the bottom plates together
Starttheboltsbyhandandtorquetheminsecurelywithapowerdriver.
Bolt the bottom plate assembly to the pedestal.
Usethe3hex/Phillipsdriveboltsyouremovedear-lier.Startallthreeboltsbyhandandtorquethemdownwithapowerdriverorhandwrench.
7
Install Casters
PositiontheLockingcastersrightandleftontheusersideandoneonpointinthemiddleoftheconvexside.Positionthetwonon-lockingcastersonthemiddlesideposi-tions.
InstallwithPhillipsdrivescrewspackagedwiththecasters.Pilotholesareprovided.
Install flipIT® Laptop Safe
Keepthelaptopsafeclosed.Thepneumaticcylinderwilldanglefreely.Thisisnormal.
Takeadiagonalapproachtogettingtheassemblythroughthecutout.
Asthepneumaticcylindercontactsthepedestalcrossbar,makesureitstaysontopofthebaranddoesnotgettrappedbelowthebar.Itwillneedtobebroughtupintopositiontoattachtotheas-sembly.
8
Watch your fingers!
Astheunitdropsintoplace,getyourfingersoutoftheway.Thismethodletsyouavoidopeningthelaptopsafeunsup-ported.
Another way:
Thelidisclosedwithatouchlatch.Pressthelatchtogetheranditwillrelease.Graspthewoodenlidandletthelaptopsafecomeopentothispoint.Keepthetrayunretracted.
Nowyoucangettheunitseatedwithouthavingfingersinthegap.
Open Laptop Safe to install collar screws
Thepneumaticcylindernormallygivesopeningforce,butithasnotbeenattachedyet.Toopenthelaptopsafe,pressonthelidtoreleasethetouchlatch.Holdthelidopentorevealthepull-outtray.Graspthetraymarked“PULL,”andpullittowardyourselfasyouraisethelid.Thetrayandlidmoveatthesametime.
9
Install Collar with 4 Screws
BEFORE you install, make sure the pneu-matic cylinder is above the pedestal cross bar so it can be pulled up into po-sition and installedonitspostinthesideofthecollar.
The reason the pneumatic is not shipped installed is to reduce the possibility for the collar to be-come sprung in shipment or during the installation process. If you must remove the collar at any time, take the pneumatic off its post before removing the collar screws.
The locking hub must be pried off before attempt-ing to press the end onto the post. The locking hub must be removed before removal, as well. When installed, press the locking hub back into place.
1
2
3
4
Install pneumatic after installing the collar
10
Install the Pneumatic
Removethelockinghub,presstheendontothepost,replacethelockinghubandpressintoplace.
Install the Lock Assembly
TheLockAssemblyhasitsowninstallationkit,hardwareandinstallationmanual.Abriefisprovidedhere.
Pleaseconsultthemanualthatcomeswiththekitforfulldetails.Thelockdesignhaschangedovertime,andmaychangeagain.Themanualthatcomeswiththelockkitwillbespecificforthatlockkit.
11
Position the Lock Assembly
PlaceQuarkupsidedownonaworksurface.Placethelockassemblyasshown.The“dog-bone”slidesalongtheflatsectionofthelockbarsoitcanbepositionedtogointotheslotinthesideoftheflipIT®LaptopSafe.Thelockisparallelwiththeunitandinstallsontheuser’sleft.Thecowlfitsoverthelockassemblytopreventtamperingwiththelock.
Locate “dogbone,” drill 1/8” pilot holes and install with kit wood screws.
Do the same for the Key Lock. Use Phillips drive screws to confirm operation. Install One-Ways one at a time for PERMANENT installation.
“Dogbone” on adjustable flat of lock bar.
Parallel Alignment
One Way Screws are PERMANENT. InstallONLYafterthelockassemblyoperatesperfectlywithPhillipsDriveScrews.ReplaceonescrewatatimewithOne-Wayssothepositionofthecomponentsremainsunchanged.
www.smartdesks.com800 770 7042
© 2009 CBT Supply, Inc. dba SMARTdesks. All rights reserved. Quark™ Qstar™ and flipIT® are trademarks of CBT Supply, Inc. flipIT® Laptop Safe Patent Pending.