Post on 09-Feb-2019
transcript
Assembly instructions V8/10/2012
ASENNUSOHJE Assembly instructions
www.ivep.cz
JEPI+OPP LEV S2.25.400.S.3
(on the top of pole; swivel parts)
JEKA+OPP CUB S2.25.400.S.3
(on the top of pole; swivel parts)
JEMU+OPP LEV S2.25.400.S.3
(one/two poles; extension set)
2
Assembly instructions V8/10/2012
Pakettien sisällöt JEPI + OPP Contens of package I + IV (LEV S2.25.400.S.3)
Package I.
Package IV.
1x
1x
3x
1x
1x
1x
3x
1x
1x
1x
+
1x
Package XI.
3
Assembly instructions V8/10/2012
Pakettien sisällöt JEKA + OPP Contens of package II + IV (CUB S2.25.400.S.3)
Package II.
Package IV.
1x 1x
1x
1x
1x
3x
3x
1x
1x
1x
1x
+
Package XI.
4
Assembly instructions V8/10/2012
Pakettien sisällöt JEMU + OPP Contens of package III + IV (LEV S2.25.400.S.3)
Package III.
Package IV.
1x 1x
1x
1x
1x
3x
3x
1x
1x
1x
1x
+
Package XI.
5
Assembly instructions V8/10/2012
Tarvittavat työvälineet Tools
6
Assembly instructions V8/10/2012
Elementtien vaaka-asennus Horizontal installation
1
2
3
4
2x
7
Assembly instructions V8/10/2012
5
5
6
6
8
Assembly instructions V8/10/2012
Elementtien pystyasennus Vertical installation
1
2-3
4
5-6
2x
2x
2x
9
Assembly instructions V8/10/2012
Maadoituspannan asennus Earhing band installation
8
7
20 Nm
20 Nm
9
10
Assembly instructions V8/10/2012
Ohjausakselin asennus Control shaft installation
10
11
11
10-11
11
Assembly instructions V8/10/2012
30 Nm
30 Nm
12
3x 3x
100 Nm
6x
13
12
Assembly instructions V8/10/2012
Ohjausvipu elementtien vaaka-asennus Control lever installation horizontal
(Huomioi vivun asento ja putken liitos, vaihda tarvittaessa) ( Notice position, change if needed)
Ohjausvipu elementtien pystyasennus Control lever installation vertical
(Huomioi vivun asento ja putken liitos, vaihda tarvittaessa) ( Notice position, change if needed)
14
30 Nm
2x
30 Nm
2x
30 Nm
4x
14
13
Assembly instructions V8/10/2012
Käsiohjaimen asennus Hand drive installation
15
50 Nm
17
16
3x
14
Assembly instructions V8/10/2012
Ohjainputken asennus Control tube installation
45 Nm
19
4x
18
18
15
Assembly instructions V8/10/2012
45 Nm 4 x
22
20 21
21 4x
23
700 mm
16
Assembly instructions V8/10/2012
Säädä tarvittaessa ohjausputken paikkaa Adjust place of tube if needed
150 mm
1500 mm
25
24
50 Nm
4x
4x
45 Nm
4 x
17
Assembly instructions V8/10/2012
26
45 Nm
45 Nm
4x
4x
18
Assembly instructions V8/10/2012
45 Nm
4x
27
19
Assembly instructions V8/10/2012
Ohjaimen säätö kiinniasennossa Adjustment in the close position
Check that all element wipes or chambers and hand drive are fully
closed
Tarkista että kaikkien elementtien piiskat tai kammiot sekä käsiohjain
on täysin kiinniasennossa.
Open nuts so that teleskope tube can move
Aukaise muttereita niin että teleskooppi putki voi liikkua
28
I
Make a mark with pen
when all are fully closed position
Tee merkki kun kaikki on täysin kiinni
asennossa
II
20
Assembly instructions V8/10/2012
Check that all elements can move open and close position stoppers . If not, move teleskope
tube more open and test againg.
Tarkista että kaikki elementit liikkuvat kiinni ja auki stoppareihin. Jos ei säädä
teleskooppiputkesta lisää pituutta ja testaa uudelleen.
45 mm
45 Nm
45 Nm
4x
4x
Open hand drive so that mark
move 45 mm. Tighten then the
nuts
Avaa käsiohjainta niin , että
merkki siirtyy 45 mm. Kiristä
mutterit
III
IV
21
Assembly instructions V8/10/2012
Ohjausvivun säätö moottoriohjaimen liikkeelle Adjustment of uplift
Vaaka-asennus / Horizontal mounting
Pystysuora asennus/ Vertical mounting
A 145 mm
B 140 mm
C 127 mm
D 122 mm
E 108 mm
F 103 mm
G 90 mm
H 86 mm
A 162 mm
B 150 mm
C 143 mm
D 130 mm
E 124 mm
F 111 mm
22
Assembly instructions V8/10/2012
Esiasennetun orren nosto Pre assembly crossarm lifting:
:
23
Assembly instructions V8/10/2012
Manufactured and supplied by:
IVEP, a.s.
Vídeňská 117a, 619 00 Brno, Czech Republic
Tel.: +420 547136 654 e-mail:marketing@ivep.cz
Fax: +420 547136 402 http:// www.ivep.cz