AUDIO VISUAL TRAININGAUDIO VISUAL TRAININGHennings Hall-Smart ClassHennings Hall-Smart Class

SMART CLASS EQUIPMENTSmart Class

LCD Projector/Built In Screen Control Panel

Credenza (DVD/VCR & P.C. inside)

TURNING ON A/V SYSTEM Smart Class

Use the key provided to you by your department head to

unlock the credenza.

TURNING ON A/V SYSTEM Smart Class

*Make sure Master Switch is on inside the credenza.

*Master Switch will light up red if it is in the ON position. Master Switch should never be turned off.

TURNING ON A/V SYSTEM Smart Class

Press the “ON” button located on the bottom right hand side of

the control panel and the projector will begin turning on.

TURNING ON A/V SYSTEM Smart Class

Please note, if you’re touch pad is not working, there will be a

remote inside the credenza. The green button on all remotes will

turn on your projector.

TURNING ON A/V SYSTEM Smart Class

Press the “ON” button located in the center of the computer

to turn it on.

Pull out mouse and keyboard from drawer above the P.C. You’ll find the monitor built into the Credenza above the

keyboard.

PROJECTING A COMPUTERSmart Class

To display the computer, press the “Input” button on the control panel until the

projector reads “Input A” on the top corner of the screen.

*If using a remote, press “INPUT” button until you see “INPUT A” on the screen. Or press button labeled “Input A” or “Input 1”.

PROJECTING A COMPUTERSmart Class

To adjust the volume coming from your *computer press the “VOL +” and “VOL -” buttons on

the control panel.

*Please note, volume must also be turned up on your P.C. to receive sound.

PROJECTING A DVDSmart Class

To play a DVD or VHS open the compartment on the right hand

side of the credenza and pull out the DVD/VCR combo player

located inside.

PROJECTING A DVDSmart Class

To play a DVD, turn on your DVD/VCR combo player by

pressing the “Power” button on the bottom left hand corner of

the player.

PROJECTING A DVDSmart Class

• Press the Eject button next to the DVD player to open it.

• Place DVD in player with label up.

• Push the Eject button again to close and load the DVD player.

PROJECTING A DVDSmart Class

Press the “DVD” button on the control panel to have projector

display the DVD player.

If there is no “DVD” button press the “INPUT” button until the projector displays the word “VIDEO” on the top corner of

the screen.

*If using a remote, press “INPUT” button until you see “VIDEO” on the screen. Or press button labeled “VIDEO” or “Input 3”.

PROJECTING A DVDSmart Class

There are 3 ways to control your DVD:

1.Use control buttons located on the control panel.

2. Use control buttons located on the DVD player itself.

3.Use the remote control located in the compartment with the player.

PLAYING A DVDSmart Class

To adjust the volume coming from the DVD press the

“VOL +” and “VOL -” buttons on the control panel.

PLAYING A DVDSmart Class

To stop the DVD press the STOP button located on the bottom left hand corner of the DVD

player.

Press the “Eject” button to retrieve your DVD.

PROJECTING A VHSSmart Class

To play a VHS, turn on your DVD/VCR combo player by

pressing the “Power” button on the bottom left hand corner of

the player.

PROJECTING A VHSSmart Class

Put your VHS tape into the slot on the right hand side of the

player.

PROJECTING A VHSSmart Class

Press the “VCR” button on the control panel to have projector

display the VHS tape.

If there is no “VCR” button, press the “INPUT” button until the projector reads “VIDEO” on

the top corner of the screen.

*If using a remote, press “INPUT” button until you see “VIDEO” on the screen. Or press button labeled “VIDEO” or “Input 3”.

PROJECTING A VHSSmart Class

There are 3 ways to control your VHS:

1.Use control buttons located on control panel.

2. Use control buttons located on the VCR player itself

3.Use the remote control, located in the compartment with the DVD/VCR.

PROJECTING A VHSSmart Class

To adjust the volume coming from the VHS press the

“VOL +” and “VOL –” buttons on the control panel.

PROJECTING A VHSSmart Class

To stop the VHS press the STOP button located on the bottom left hand corner of the VCR.

Press the “Eject” button to retrieve your VHS.

TURNING OFF THE A/V SYSTEM Smart Class

To turn off the A/V System press the “OFF” button located

on the control panel twice.

*If using a remote, press green “Power” button twice, or press “Off” Button twice.

TURNING OFF THE A/V SYSTEM Smart Class

Turn off the P.C. and DVD /VCR player and you have completed shutting down the A/V system.

Please place back all items removed from the credenza.

(remotes, mouse/keyboard, etc.)

TURNING OFF A/V SYSTEM Smart Class

Use the key provided to you by your department head to

lock the credenza.

AUDIO VISUAL CONTACT INFOSmart Class

• Office Phone: Ext. 76120

• Office Email: avt@kean.edu

• Office Location: Technology Building Room 110

• Office Website: http://www.kean.edu/~avt/

This presentation was created by Katherine Roba kroba@kean.edu ~ 908 737 6122