Post on 25-Mar-2018
transcript
ALLIED-SIGNAL BENDIX EQUIVALENT TEST SYSTEMS
SPECIALIZEDAVIONICS TEST EQUIPMENT
CATALOG SUPPLEMENT
AVIONICS SPECIALIST, INC.
www.avionics
-spec
ialist
.com
Avionics Specialist, Inc.
Avionics Specialist, Inc.3833 Premier Ave.Memphis, Tennessee 38118
Specialized Avionics Test EquipmentProduct Catalog Supplemant
Ph: 901-362-9700Fax: 901-794-8276
www.avionics-specialist.com
01-01-02
Allied Signal Bendix Equivalent Test Systems
Avionics Specialist, Inc.3833 Premier Ave.Memphis, Tennessee 38118
Ph: 901-362-9700Fax: 901-794-8276
www.avionics-specialist.com
01-01-02
Specialized Avionics Test EquipmentProduct Catalog Supplement
Avionics Specialist, Inc.
DAC International6702 McNeil DriveAustin, TX 78729-7799Contact: Russ SmithPh. 512-331-5323Fax. 512-331-4516email: rusmith@banner.comwww.dacint.com
Dallas Avionics, Inc.2525 Santa Anna Ave.Dallas, TX 75228-1671 Contact: Scott DavisPh. 214-320-9770Fax. 214-320-1057email: sd@dallasavionics.comwww.dallasavionics.com
EDMO Distributors, Inc.5505 E. Rutter Ave.Spokane, WA 99212Contact: Pat OlsonPh. 509-535-8280Fax. 509-535-8266email: pato@edmo.comwww.edmo.com
The Memphis Group3900 Willow Lake Blvd.Memphis, TN 38118-7040 Contact: Kris TriplettPh. 901-362-8600Fax. 901-365-1482email: ktriplett@memphisgrp.comwww.memphisgrp.com
Glendale International533 Rayleigh RoadThundersley, EssexSS7 3TN EnglandContact: Ian ParkinsPh. +44(0)1268-741770Fax. +44(0)1268-741780email: iparkins@glendale-int.co.ukwww.glendale-int.co.uk
Richardson Electronics, Ltd.40 W 267 Keslinger RoadLaFox, IL 60147Contact: Seal TealPh. 630-208-2588Fax. 630-208-2550email: sean@rell.comwww.rell.com
ASI Test Equipment Distributors:
Allied Signal Bendix Equivalent Test Systems
ALLIED-SIGNAL BENDIX EQUIVALENT TEST SYSTEMS 01/01/02
ASI MN BENDIX MN BENDIX PN DESCRIPTION LIST PRICEASI-1207A TS-1207A 4000595-0701 RADAR TEST SET 660.00ASI-152-1 RDT-1F 1038139-0501 RADAR TEST PANEL 16,700.00ASI-152-2 RDT-1FB 2041351-0102 RADAR TEST PANEL 18,030.00ASI-153-1 ATT-1F 2038270-0501 RADAR ANTENNA TEST PANEL 11,670.00ASI-153-2 ATT-1FB 2038270-0502 RADAR ANTENNA TEST PANEL 11,670.00ASI-153-3 ATT-1FB 2038270-0503 RADAR ANTENNA TEST PANEL 26,550.00ASI-153-4 ANT-1FBM 8056275-0501 SECTOR SCAN TEST ADAPTER 14,900.00ASI-154-1 RCT-1F 2038326-0501 RADAR SYSTEM TEST PANEL 21,160.00ASI-154-2 RCT-1FB 2041349-0102 RADAR SYSTEM TEST PANEL 22,290.00ASI-169 RST-1A 2064746-0501 PORTABLE STABILIZATION TEST SET 5,310.00ASI-169-2 RST-4A 2041797-0401 PORTABLE RADAR TEST SET 4,995.00ASI-170 RFT-1A 2038142-0501 PORTABLE RADAR TEST SET 4,460.00ASI-171 RDT-1A 2037736-0501 RADAR SYSTEM TEST PANEL 10,050.00ASI-172 RDT-1B 2037737-0501 RADAR TEST PANEL 4,460.00ASI-173 PPT-1A 2037738-0501 RADAR INDICATOR TEST PANEL 11,160.00ASI-174 PPT-1B 2038141-0501 RADAR INDICATOR TEST PANEL 11,160.00ASI-175 AMT-51A 2037028-5103 PORTABLE ALTIMETER TEST SET 5,580.00ASI-175-2 AMT-52A 2041595-5201 PORTABLE ALTIMETER TEST SET 6,995.00ASI-177-1 RNT-26A 2064139-0501 VHF NAVIGATION TEST PANEL 12,500.00ASI-177-2 RNT-260A 3604031-0501 VOR/ILS TEST PANEL 12,500.00ASI-197 PPT-1CG 2041323-0101 RADAR TEST PATTERN GENERATOR 2,440.00ASI-198 2039597-0501 RADAR TEST PATTERN GEN ADAPTER 1,890.00ASI-199 ALT-51A 2037120-0501 RADAR ALTIMETER TEST PANEL 27,350.00ASI-202 DFT-73AA 2064943-0501 ADF SYSTEM TEST PANEL 9,360.00ASI-244-1 PPT-1FB 2041350-0101 RADAR INDICATOR TEST PANEL 24,950.00ASI-244-2 PPT-1FB 2041350-0102 RADAR INDICATOR TEST PANEL 29,950.00ASI-244-3 2039817-0501 CON-1FB TEST ADAPTER PORASI-244-4 8050799-0501 CON-1TB(M) TEST ADAPTER PORASI-252-1 COT-1FB 2041348-0102 RADAR CONTROL TEST PANEL 8,880.00ASI-252-2 COT-4A 2041593-0401 RADAR CONTROL TEST PANEL 12,500.00ASI-360 RADAR SYSTEM TEST PANEL 7,260.00ASI-413-1 RIT-32A 2070809-3201 ILS RECEIVER TEST PANEL 17,950.00ASI-413-2 RIG-32A 2070776-3201 ILS AUDIO GENERATOR 7,950.00ASI-420-1 RNT-34A 2041341-3401 RNA-34A ADAPTER PANEL PORASI-420-2 ADT-34AF 3614307-3401 RNA-34AF ADAPTER PANEL PORASI-422 CPT-83A 2041065-8301 GPW SYSTEM TEST PANEL 18,900.00ASI-423-1 IUT-1SB 3614367-0101 AIU TEST PANEL 18,995.00ASI-423-2 IUT-1MB 3614662-0101 CONTROL TEST PANEL PORASI-424-1 RVT-33A 2070811-3301 VOR RECEIVER TEST PANEL 29,950.00ASI-424-2 RVG-33A 2070810-3301 VOR AUDIO GENERATOR 11,950.00ASI-425 RTT-41A 2037676-0501 TRANSCEIVER TEST PANEL PORASI-741 RMT-4A 8055325-0401 DOPPLER SIGNAL GENERATOR 10,630.00ASI-742 RCT-4A 2041589-0401 RADAR SYSTEM TEST PANEL 31,910.00ASI-743 AIT-4A 8074503-0401 TCAS ADAPTER TEST PANEL 18,080.00ASI-760 PPT-4A 2041591-0401 RADAR INDICATOR TEST PANEL 29,950.00ASI-770 AST-4A 2041886-0401 RADAR ANTENNA SIMULATOR TEST PANEL 19,950.00ASI-771 ATT-4A 2041592-0401 RADAR ANTENNA TEST PANEL 14,950.00
PRICES SUBJECT TO CHANGE WITHOUT NOTICE POR-PRICE ON REQUEST
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
RDR-1F Radar Test Panel ASI-152-1
Units Tested:RDR-1F
Description:The ASI-152-1 Radar Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix RDR-1F Weather Radar Receiver-Transmitter.
The Test Panel contains circuitry for simulating loads on the R/T unit servo and resolver amplifiers. The ASI-152-1 also has the ability to simulate the CON-1( ) Control Panel which eliminates the need for additional system components during bench testing.
The ASI-152-1 includes all test cables required to interconnect the R/T to the Test Panel.
Test panels designed to test other units of the RDR-1F Weather Radar System are also available from Avionics Specialist, Inc. These test panels are listed in the optional equipment section below.
OEM Equivalent:OEM: BendixModel Number: RDT-1FPart Number: 2038139-0501Manual: I.B. 1102ET / 34-42-55Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R2
Equipment Supplied:
Depth: 17.00"Power Requirements: 115 VAC 400 Hz
Specifications:Height: 10.50" Width: 19.00"
ASI-152-2RDR-1FB Radar Test Panel
DescriptionCable, ASI-152-1 to RDR-1F (W101)Cable, ASI-152-1 to RDR-1F (W102)Cable, ASI-152-1 to RDR-1F (W103)Cable, ASI-152-1 PWR Connector (W104)
OEM PN2038272-05012038273-05012038274-05012038275-0501
ASI MNASI-15-2AASI-15-2BASI-15-2CASI-15-2D
ASI MNASI-153-1ASI-154-1ASI-174
OEM PN2038070-05012038326-05012038141-0501
DescriptionANT-1T Radar Ant Test Panel (ATT-1F)RDR-1F Radar System Test Panel (RCT-1F)PPI-1 Radar Indicator Test Panel (PPT-1B)
Optional Equipment:
The ASI-152-2 Radar Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix RDR-1FB System Weather Radar Receiver-Transmitters (RTA-1FB), including the RTA-1FB(M) which have sector scan and variable STC capability.
The Test Panel contains circuitry for simulating loads on the R/T unit servo and resolver amplifiers. The ASI-152-2 also has the ability to simulate the CON-1SB Control Panel which eliminates the need for additional system components during bench testing.
The ASI-152-2 includes all test cables required to interconnect the R/T to the Test Panel.
Test panels designed to test other units of the RDR-1FB Weather Radar System are also available from Avionics Specialist, Inc. These test panels are listed in the optional equipment section below.
Specifications:
DescriptionANT-1T Radar Ant Test Panel (ATT-1FB)RDR-1F Radar System Test Panel (RCT-1FB)PPI-1FB Radar Indicator Test Panel (PPT-1FB)CON-1RB/SB Control Test Panel (COT-1FB)
OEM PN2038070-05012038326-05012041350-01012041348-0102
ASI MNASI-153-1ASI-154-1ASI-244-1ASI-252-1
DescriptionCable, ASI-152-2 to RTA-1FB/FB(M) (W101)Cable, ASI-152-2 to RTA-1FB/FB(M) (W102)Cable, ASI-152-2 to RTA-1FB/FB(M) (W103)Cable, ASI-152-2 PWR Connector (W104)
OEM PN8056334-05012041576-05022038274-05012038275-0502
ASI MNASI-15-22AASI-15-22BASI-15-22CASI-15-22D
Equipment Supplied: Optional Equipment:
Width: 19.00"Power Requirements: 115 VAC 400 HzHeight: 10.50" Depth: 17.00"
RTA-1FBRTA-1FB(M)
Units Tested:
OEM: BendixModel Number: RDT-1FBPart Number: 2041351-0102Manual: I.B. 1103AT-1 / 34-43-08Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Description:
OEM Equivalent:
ASI-152-1
115 VAC 400 Hz
RADAR XMTR-RCVR TEST PANEL
115 VAC 400 Hz
RADAR XMTR-RCVR TEST PANEL ASI-152-2
STCON
-28VCONTSCOPETRIG TARGET
10A OFF
SYS-2 POWER ALERT
SCOPE SEL CONT ANTFAULT
VIDEO 2VIDEO 1 STC
TARGETRANGE62
71
43 5
AZON
P-TTEST
AZ-ZTEST
AZ-XTEST
-28VCONT
STCON
P-TTEST
AZON
AZ-XTEST
AZ-ZTESTRESET
TARGETTRIG SCOPE SYS-2
OFF10A
POWER RESETALERT
AZ DRIVEREVERSE
SOFTSTART
REF
PITCH
AMPSOFFRT
FAULT
UP 2
SCOPE SEL CONT
LUP
TILT
ROLL
IFGAIN
DN 1
P-TDN R
62INPUT1
71
SUPPR
BEACONSTC
2
VIDEO4
3 5
REF
PITCH
OFFRTFAULT
ANTFAULT
AZ DRIVEA B
UP
AMPS
2
UP
TILT
IFGAIN
TARGETRANGE
OFF DN
L
ROLL
1
P-TDN R
8 10 12
FN SEL
EXT MTR
MAPOTR
NOR
TESTSTBY NOMINAL
4
02
20
166 14
18
108 12
AFCCNTRL
SA TESTIN115 VAC
400 HZ
MTR SEL
ANT MAG
FN SEL
SHORT
DRCT26 VACAMPS X
TALPWR
28 VDC
REV
30 IN1WX
STDBY
TEST 2LONG
SKEENBL
BCN
MAP
AFCCNTRL
115 VAC400 HZ
EXT MTRPILOT ALERT
MONITOR
ANT
SA TESTIN
MTR SEL
MAG
26 VAC
NOMINAL PWRPILOT ALERT
ADJ
28 VDC
200
42
6 1618
14
OFF
DRCTAMPS X
TALREV
ANT COMP22 IN VAR STC
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
R2
The ASI-153-1 Radar Antenna Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix ANT-1T Weather Radar Antenna.
The ASI-153-1 circuitry provides input power, simulated data, switching, and monitoring required for proper testing and calibration of the antenna with a minimum of external test equipment. The test panel contains three variable synchros that simulate Gyro Roll, Gyro Pitch, and CON-1( ) Tilt Control.
The ASI-153-1 includes a test interconnect cable for the ANT-1T.
Specifications:
DescriptionRDR-1F Radar System Test Panel (RCT-1F)
ASI MNASI-154-1
OEM PN2038326-0501
OEM PN2038308-05012038309-0501
DescriptionCable, ASI-153-1 PWR Connector (W101)Cable, ASI-153-1 to ANT-1T (W102)
ASI MNASI-15-3AASI-15-3B
Equipment Supplied:Optional Equipment:
Width: 19.00"Power Requirements: 115 VAC 400 Hz / 28 VDCHeight: 14.00" Depth: 17.00"
Units Tested:ANT-1T
115 VAC
NULL EXT MTR
26 VAC27.5 VDCPOWER
ANT-1T Radar Antenna Test Panel ASI-153-1
OEM: BendixModel Number: ATT-1FPart Number: 2038270-0501Manual: I.B. 1102CT / 34-42-53Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Description:
OEM Equivalent:RADAR ANTENNA TEST PANEL ASI-153
The ASI-153-2 Radar Antenna Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix ANT-1T/1TB Weather Radar Antenna.
The ASI-153-2 circuitry provides input power, simulated data, switching, and monitoring required for proper testing and calibration of the antenna with a minimum of external test equipment. The test panel contains three variable synchros that simulate Gyro Roll, Gyro Pitch, and CON-1( )B Tilt Control.
The ASI-153-2 includes a test interconnect cable for the ANT-1TB.
DescriptionRDR-1FB Radar System Test Panel (RCT-1FB)
Power Requirements: 115 VAC 400 Hz / 28 VDC
DescriptionCable, ASI-153-2 PWR Connector (W101)Cable, ASI-153-2 to ANT-1TB (W102)
OEM PN2038308-05012038309-0501
ASI MNASI-15-3AASI-15-3B
ASI MNASI-154-2
OEM PN2041349-0102
ANT-1T
Equipment Supplied:
Units Tested:Width: 19.00"Height: 14.00"
Optional Equipment:
Specifications:
NULL
POWER115 VAC
Depth: 17.00"
27.5 VDC 26 VAC
EXT MTR
RADAR ANTENNA TEST PANEL
ANT-1TB Radar Antenna Test Panel
OEM: BendixModel Number: ATT-1FBPart Number: 2038270-0502Manual: I.B. 1103ET / 34-43-07Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Description:
OEM Equivalent:
ASI-153-2
ASI-153
ANT-1TB(M) Radar Antenna Test Panel ASI-153-3
Description:The ASI-153-3 is identical to the ASI-153-2 with the addition of the ASI-153-4 Sector Scan Test Adapter and the ASI-15-3C Test Cable.
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: ATT-1FBPart Number: 2038270-0503Manual: I.B. 1102CT / 34-42-53Manual Figure: 1
OEM Equivalent: Units Tested:ANT-1TANT-1TBANT-1TB(M)
ASI MNASI-15-3AASI-15-3BASI-15-3CASI-153-4
OEM PN2038308-05012038309-05018056302-05018056275-0501
DescriptionCable, ASI-153-3 PWR Connector (W101)Cable, ASI-153-3 to ANT-1TB (W102)Cable, ASI-153-3 to ANT-1TB(M) (W103)Sector Scan Test Adapter (ANT-1FBM)
Equipment Supplied:
STAB ERROR5° F.S.
H ILOOFF OFF2A
EZ SEL
STABON ON
DATA PHASE SF
SCRCRF
2°
3°
8°
150
7°
8°9°
4°6°
5°
120
9060
30
210 3°
2°1°0°
180
300270
240
3300
4°5°
6°7°
1° 0° 9°2°
3°
8°
150
7°
8°9°
4°6°
5°
120
9060
30
210 3°
2°1°0°
180
300270
240
3300
4°5°
6°7°
1° 0° 9°
PITCH TILT
9030
10020
0 V ARIAC 120
11010
DEGREES
705060
400 Hz ADJUST
8040
6
10 0 2105 5
4
2025 25
2015 15 0
.75A2A
FN SEL
RUN EL EZAZ EZ
2°
3°
8°
150
7°
8°9°
4°6°
5°
120
9060
30
210 3°
2°1°0°
180
300270
240
3300
4°5°
6°7°
1° 0° 9°
ROLL
ROT Z26 VAC
STAB OUT
ROLL OUT
115 VACNOMINAL
MTR SEL
27.5 VDC
1412108
18 AZ DATA16
AZ SYN ROT I20
LO HI2A OFFOFF 2A .75A
RC SC
ONSTAB
ON
DATA PHASE SF
EZ SEL
2°
3°
8°
150
7°
8°9°
4°6°
5°
120
9060
30
210 3°
2°1°0°
180
300270
240
3300
4°5°
6°7°
1° 0° 9°2°
3°
8°
150
7°
8°9°
4°6°
5°
120
9060
30
210 3°
2°1°0°
180
300270
240
3300
4°5°
6°7°
1° 0° 9°
RF
PITCH TILT
10 110
120V ARIAC0
20 100
STAB ERROR5° F.S.
400 Hz ADJUST
60
30 90
40 80
50 70
01555 10
2025
204 6
1510
2520
DEGREES
EL EZRUN
FN SEL
2°
3°
8°
150
7°
8°9°
4°6°
5°
120
9060
30
210 3°
2°1°0°
180
300270
240
3300
4°5°
6°7°
1° 0° 9°
AZ EZ
ROLL
NOMINAL
ROLL OUT
STAB OUT
27.5 VDC
MTR SEL
115 VAC
20AZ DATA
ROT IAZ SYN
26 VAC ROT Z
1618
8 10 12 14
ANT-1TB
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
RDR-1F Radar System Test Panel ASI-154-1
Units Tested:RDR-1FANT-1TPPI-1L
Description:The ASI-154-1 Radar System Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix RDR-1F Weather Radar System. The Test Panel assists in determining the operational status of any unit of an RDR-1F Radar System. The ASI-154-1 is comparable to the complete aircraft radar wiring harness and, in conjunction with standard shop test equipment, allows one unit at a time to be tested by substitution with a known serviceable unit.
The ASI-154-1 includes test interconnect cables for the Antenna, Indicator, and R/T. A user supplied Radar Control (CON-1R/1S) is required for proper operation of the test panel. The control mounts directly on the front panel of the ASI-154-1 and can be easily interchanged with other controls as required during testing.
Test panels designed to test each unit of the RDR-1F Weather Radar System individually are also available from Avionics Specialist, Inc. These test panels are listed in the optional equipment section below.
OEM Equivalent:OEM: BendixModel Number: RCT-1FPart Number: 2038326-0501Manual: I.B. 1102BT / 34-42-52Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R1
Equipment Supplied:
Depth: 17.00"Power Requirements: 115 VAC 400 Hz
Specifications:Height: 15.75" Width: 19.00"
ASI-154-2RDR-1FB Radar System Test Panel
DescriptionCable, ASI-154-1 to RDR-1F (W101)Cable, ASI-154-1 to PPI-1L (W102)Cable, ASI-154-1 PWR Connector (W103)Cable, ASI-154-1 to ANT-1T (W104)
OEM PN2038350-05012038351-05012038352-05012038352-0501
ASI MNASI-15-4AASI-15-4BASI-15-4CASI-15-4D
ASI MNASI-152-1ASI-153-1ASI-174
OEM PN2038139-05012038070-05012038141-0501
DescriptionRDR-1F Radar Test Panel (RDT-1F)ANT-1T Radar Ant Test Panel (ATT-1F)PPI-1 Radar Indicator Test Panel (PPT-1B)
Optional Equipment:
RESET
IS-IR SYS 1
21VID
2025
40
10
RADAR SYSTEM TEST PANELRADAR SYSTEM TEST PANEL
PULSEDLY
IR SYS 2
FN SEL
20
30
MAG
STAB ERR
OSC TEST
PITCH
101015
TEST MTR
5 5015
2520
60
110
80
400 Hz ADJUST
115 VAC 400 Hz
VARIAC0
50
120
70
100
90
RTFAULT
PILOTALERT
ANTFAULT
WARMSPARE
EXT MTR
02
4 6
MON MTR
108 1412
ASI-154-1
2018
16
115 VAC 400 Hz
TEST MTR
RADAR SYSTEM TEST PANELRADAR SYSTEM TEST PANEL
EXT MTR
MON MTR
ASI-154-2
The ASI-154-2 Radar System Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix RDR-1FB Weather Radar System. The Test Panel assists in determining the operational status of any unit of an RDR-1FB Radar System. The ASI-154-2 is comparable to the complete aircraft radar wiring harness and, in conjunction with standard shop test equipment, allows one unit at a time to be tested by substitution with a known serviceable unit. The ASI-154-2 also includes circuitry and wiring required to test RDR-1FB(M) Radar Systems with sector scan and variable STC capability.
The ASI-154-2 includes test interconnect cables for the Antenna, Indicator, and R/T. A user supplied Radar Control (CON-1RB/1SB) is required for proper operation of the test panel. The control mounts directly on the front panel of the ASI-154-2 and can be easily interchanged with other controls as required during testing.
Test panels designed to test each unit of the RDR-1FB Weather Radar System individually are also available from Avionics Specialist, Inc. These test panels are listed in the optional equipment section below.
RTA-1TB / RTA-1FB / RTA-1FB(M)ANT-1TB / ANT-1TB(M)CON-1RB / CON-1SB / CON-1SB(M) / CON-1TB(M)PPI-1TB / PPI-1TB(M)
DescriptionRDR-1FB Radar Test Panel (RDT-1FB)ANT-1TB Radar Ant Test Panel (ATT-1FB)PPI-1FB Radar Ind Test Panel (PPT-1FB)CON-1RB/1SB Control Test Panel (COT-1FB)
ASI MNASI-15-42AASI-15-42BASI-15-42CASI-15-42DASI-15-42E
OEM PN8056346-05012041574-05022038352-05022038353-05028056342-0501
DescriptionCable, ASI-154-2 to RDR-1FB/TB (W101)Cable, ASI-154-2 to PPI-1TB (W102)Cable, ASI-154-2 PWR Connector (W103)Cable, ASI-154-2 to ANT-1TB (W104)Cable, ASI-154-2 to CON-TB (W105)
ASI MNASI-152-2ASI-153-2ASI-244-1ASI-252-1
OEM PN2038139-05012038270-05022041350-01012041348-0102
Equipment Supplied:Power Requirements: 115 VAC 400 Hz
Optional Equipment:
Width: 19.00"Specifications:Height: 15.75" Depth: 17.00"
Units Tested:
OEM: BendixModel Number: RCT-1FBPart Number: 2041349-0102Manual: I.B. 1103CT-1 / 34-43-10Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Description:
OEM Equivalent:
CON-1RCON-1S
AFC
OFF
REV
DIR
CTRL SEL
2°
3°
8°
150
7°
8°9°
4°6°
5°
120
9060
30
210 3°
2°1°0°
180
300270
240
3300
4°5°
6°7°
1° 0° 9°
ROLL ADJ
28 VDC PWR
-28 VDCOFF
115 VAC
MTR SEL
J3-L26 VAC
115 VAC DLYD
P2-3526 VAC
28 VDC CTRL
10A OFFTV 10DN
PULSESTCTVIN21
TRIGSTCONPOWERPPI
PITCH0
ROLLON
ELON
PITCHUP
STABON
-103OFF10A 10DN
2SUPPR
BCNSTC PULSETRIG
1
SUPPRIN
21VID
PULSEDLY
-101-102
STCONPOWER
SKEENBL
PITCH0
PITCHUP
ROLLON
STABON
ELON
RTFAULT
ANTFAULT
WARMSPARERESET
PILOTALERT
30 INCH 28 VDC CTRL115 VAC DLYDDIR PITCH
IS-IR SYS 1 IR SYS 22°
3°
8°
150
7°
8°9°
4°6°
5°
120
9060
30
210 3°
2°1°0°
180
300270
240
3300
4°5°
6°7°
1° 0° 9°
CTRL SEL
KC-10
VARIAC0 120
400 Hz ADJUST ROLL ADJ
10020
10 110
FN SEL
STAB ERRAFC
OFF OSC TEST
FAN
8040
9030
MTR SEL
607050
28 VDC PWR115 VAC
OFF -28 VDC
MAGREV
ANT COMP22 INCH
J3-L26 VAC
P2-3526 VAC
55 0
2020101015 15
2525
148 1210
1820
162
0
46
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
Portable Stabilization Test Set ASI-169
OEM PN2037736-05012037737-0501
Optional Equipment:ASI MNASI-171ASI-172
DescriptionRadar System Test Panel (RDT-1A)Radar Antenna Test Panel (RDT-1B)
Units Tested:RDR-1E/1ED Weather Radar System
Description:The ASI-169 Stabilization Test Set is designed to facilitate testing and adjustment of the antenna stabilization circuits in the Bendix RDR-1E/ED Weather System. The unit is portable and derives all of its input power and test signals from the connector located on the front of the RDR-1E/ED Receiver-Transmitter.
The ASI-169 is intended to be used primarily as a ramp test set to optimize the stabilization gain adjustments to a given antenna in a given aircraft. The ASI-169 is enclosed in a rugged plastic case.
OEM Equivalent:OEM: BendixModel Number: RST-1APart Number: 2064746-0501Manual: I.B. 1101STManual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R2
Equipment Supplied:
Depth: 4.00"Power Requirements: From UUT
Specifications:Height: 8.00" Width: 8.50"
DescriptionTest Procedure Placard, ANT-1STest Procedure Placard, ANT-1M/1N/1PTest Procedure Placard, ANT-1F/1G
OEM PN2034816-00012034816-00022034816-0003
ASI MNASI-16-9AASI-16-9BASI-16-9C
The ASI-169-2 Portable Radar Test Set interfaces to the ATE connectors of the Bendix RTA-4A Receiver Transmitter for testing purposes.
The Test Set provides the capability of one step and automatic display of all circuit module fault codes stored in the RTA-4A fault memory, starting with the last stored fault code. It provides the ability to erase all stored fault codes and to cut off transmission of fault codes to the PPI during RDR-4A system test. The ASI-169-2 is enclosed in a lightweight, rugged plastic case. Power Requirements: From UUT
DescriptionTest Procedure Placard, RTA-4A
OEM PN3611841-0001
ASI MNASI-16-92A
Equipment Supplied:OEM PN2041589-0401
ASI MNASI-742
DescriptionRadar System Test Panel (RCT-4A)
Optional Equipment:
Width: 8.50"Height: 8.00"Specifications:
Depth: 4.00"
RDT-4A / RDR-4A Weather Radar System
Units Tested:
Portable Radar Test Set ASI-169-2
OEM: BendixModel Number: RST-4APart Number: 2041797-0401Manual: I.B. 1104GT / 34-41-61Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Description:
OEM Equivalent:
OFF AZ ERR
ASI-170 PORTABLE RADAR TEST SET
OSC TEST
10° PITCH
STAB ERR
5° FS ANT-1( )
10° ROLLGYRO PITCH
ANT POS
GYRO ROLL
PRESS FOR ANT-1S
ASI-169 STABILIZATION TEST SET
25
DC MICROAMPERES
20 20
25
051015
5 10 15
+28 VDC OSC TEST
26 VACOFF
-28 VDC
AFC
REVDIR MAG
STAB ERR
PITCH
DC MICROAMPERES
25
15105
1510 5 0
25
2020
FAULTMEMORY
ASI-169-2 RADAR TEST SET
ERASE
STEP
AUTO
TEST
OFF
CAUTION: TURN OFF THE RADAR AND THE ASI-169-2 TEST SET BEFORE THE CABLE IS CONNECTED OR
D ISCONNECTED FROM THE RTA-4A ATE CONNECTORS
ERASE RESET STEP
FAULT COUNT FAULT CODE
RDR-1F Weather Radar System
The ASI-170 Portable Radar Test Set is designed to facilitate testing of the Bendix RDR-1F Weather Radar System. The Test Set may be used as a ramp unit for initial installation checkout or as a shop bench test unit for performing fault isolation test procedures on the R/T unit.
All necessary input power and signals are received from the test connector located on the front panel of the RDR-1F Receiver- Transmitter unit. The ASI-170 is enclosed in a lightweight, rugged plastic case.
OEM PN2035426-0002
ASI MNASI-17-0A
DescriptionTest Procedure Placard
OEM PN2037736-0501
ASI MNASI-171
DescriptionRadar System Test Panel (RDT-1A)
Equipment Supplied:
Depth: 4.00"Height: 8.00" Width: 8.50"Power Requirements: From UUT
Optional Equipment:
Specifications:
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: RFT-1APart Number: 2038142-0501Manual: I.B. 1102AT / 34-42-51Manual Figure: 1
Description:
Units Tested:
OEM Equivalent:
ASI-170Portable Radar Test Set
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
RDR-1 Radar System Test Panel ASI-171
Units Tested:RDR-1ERDR-1EDSYN-1B
Description:The ASI-171 Radar System Test Panel provides a centralized means for testing the receiver-transmitter, synchronizer and indicator of the Bendix RDR-1( ) Weather Radar Systems prior to the RDR-1F Radar System.
The ASI-171 contains circuitry for simulating the antenna and control panel, thus eliminating the need for these units on the test bench.
The ASI-171 includes three interconnect cables and a load box required for testing.
Associated test panels designed to test the RDR-1( ) Radar System are listed in the optional equipment section.
OEM Equivalent:OEM: BendixModel Number: RDT-1APart Number: 2037736-0501Manual: I.B. 1101ATManual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R2
Equipment Supplied:
Depth: 13.00"Power Requirements: 115 VAC 400 Hz / 27.5 VDC
Specifications:Height: 10.50" Width: 19.00"
ASI-172Radar Test Panel
DescriptionCable, ASI-171 to RDR-1( ) (W1)Cable, ASI-171 to PPI-1( ) (W2)Cable, ASI-171 to SYN-1B (W3)Load Box, RDR/PPI (A1)
OEM PN2036958-05012036957-05012036959-0501NPN
ASI MNASI-17-1AASI-17-1BASI-17-1CASI-17-1D
ASI MNASI-169ASI-172ASI-173ASI-174
OEM PN2064746-05012037737-05012037738-05012038141-0501
DescriptionPortable Stabilization Test Set (RST-1A)Radar Test Panel (RDT-1B)Radar Indicator Test Panel (PPT-1A)Radar Indicator Test Panel (PPT-1B)
Optional Equipment:
The ASI-172 Radar Test panel is designed to test the operational functions of the Bendix CON-1 Radar Control and the ANT-1 Radar Antenna, with the exception of the antenna's RF performance.
The ASI-171 test functions are determined by a combination of front panel switches. A variac allows the user to adjust the proper test voltages. The test panel also features a dual tuning eye which indicates synchro null and rotation reference condition.
The ASI-171 includes two cables for testing the most common CON-1 Controls and ANT-1 Antennas. Other available cables are listed in the optional equipment area.
Associated test panels designed to test the RDR-1( ) Radar System are listed in the optional equipment section.
Specifications:
DescriptionCable, CON-1J/L/N (W102)Cable, ANT-1A/B/C/D/E/J/L/M/N/P/S (W201)
OEM PN2037016-05012037018-0501
ASI MNASI-17-2AASI-17-2B
Equipment Supplied:
Width: 19.00"Power Requirements: 115 VAC 400 HzHeight: 3.50" Depth: 6.00"
CON-1ACON-1BCON-1DCON-1JCON-1LCON-1NCON-1NB
Units Tested:
OEM: BendixModel Number: RDT-1BPart Number: 2037737-0501Manual: I.B. 1101BTManual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Description:
OEM Equivalent:
PPI-1DPPI-1EPPI-1E-1
PPI-1E-2PPI-1GPPI-1GT
PPI-1MPPI-1P
ANT-1AANT-1BANT-1CANT-1DANT-1EANT-1G
ANT-1JANT-1LANT-1MANT-1NANT-1PANT-1S
ASI MNASI-169ASI-171ASI-173ASI-174ASI-17-2CASI-17-2DASI-17-2E
DescriptionPortable Stabilization Test Set (RST-1A)Radar System Test Panel (RDT-1A)Radar Indicator Test Panel (PPT-1A)Radar Indicator Test Panel (PPT-1B)Cable, CON-1A/B/D (W101)Cable, CON-1NB (W103)Cable, ANT-1G (W202)
OEM PN2064746-05012037736-05012037738-05012038141-05012037015-05012037017-05012037019-0501
Optional Equipment:
2 457 390 530AC
7
V ARIACOFF
20
ON
0
10
1003
4
120 1
110 2
6
9
8
1
2
11
10
AC VOLTS1
0
5AF
15
GND
ASI-171 RADAR TEST PANEL
AC VOLTS
30
REG TEST
IF GAIN
DC VOLTS
+140 VROLL
602A
40
50
2A 10A
CON-1( )6
80
70ROLL
4
CW CCW
SYNCHROS
OFF
STANDBY ON
NORMAL
ANT LOC
DRD-1ESYN-1B
SYN-18 MOD
DC AC
TR
TP
TILT
PITCH
DRD-1ESYN-1B
BEACONCONTOUR STC
CHECKTEST
+28 V
-250 V +300 V
JACK
200 10
TILT DRIVETORQUE
TILT SELECTOR
DOWN
TILT ENERGIZE
DC METER
UP
0
5
EZ
OFF
SWEEP
AZIMUTH
TEST
TRIGGER
ROLL ZERO CHECK
MOTORS
ONNULL IND OFFON
5
10A
3
RDR
ANT LOC
MAP10
90 IL IN IP
VIDEOPPI
HI VOLTTX
RDR-1DFAN PP1
TESTCONTOUR
40 50
MOTOR TEST
DC VOLT
0 PPI-1G
#1 #2
YOKE DRIVETORQUE
ONOFF
10
15
YOKE
AZ AMP
AC METER
SWEEP
PRI TEST
EZ
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
Radar Indicator Test Panel ASI-173
OEM PNOptional Equipment:ASI MN Description
Units Tested:PPI-1DPPI-1E-2PPI-1GPPI-1GT
Description:The ASI-173 Radar Indicator Test Panel is designed to facilitate bench testing, alignment, and troubleshooting of the Bendix PPI-1D, PPI-1E-2, PPI-1G, and PPI-1GT Radar Indicators. The test panel is intended to provide a centralized means of conveniently and accurately determining equipment performance with a minimum amount of ancillary test equipment.
The Radar Indicator Test Panel contains circuitry for applying a variety of video signals to the PPI-1( ). These include video pulses, system noise, noise bursts, and noise with STC action. Front panel controls facilitate the performance of numerous tests to evaluate the operation of the PPI-1( ).
The ASI-173 contains the power supply and wave form generator used in a typical RDR-1E Receiver-Transmitter unit. The power supply provides 17.5, 50, 140, 300, and -250 vdc. The 18 vac reference phase voltage and variable control voltage to the drive motor are also generated by the test panel. The wave form generator emits trigger pulses at 200 and 400 Hz and provides the necessary gate voltage for producing noise bursts.
The ASI-173 includes two test cables required for proper operation.
OEM Equivalent:OEM: BendixModel Number: PPT-1APart Number: 2037738-0501Manual: I.B. 1101PTManual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R2
Equipment Supplied:
Depth: 12.75"Power Requirements: 115 VAC 400 Hz / 27.5 VDC
Specifications:Height: 10.50" Width: 19.00"
The ASI-174 Radar Indicator Test Panel provides a convenient, self-contained means for testing, alignment, and troubleshooting the Bendix PPI-1L, PPI-1N, PPI-1P, PPI-1T, and PPI-1U Weather Radar Indicators.
The ASI-174 contains power supply, wave form generator, and azimuth circuitry thus eliminating the need for other system components. Front panel controls facilitate the performance of numerous tests to evaluate the proper operation of the PPI-1( ).
When used in conjunction with the ASI-743 (AIT-4A) TCAS PPT Adapter Test Panel the ASI-174 has the capability to test TCAS modified PPI-1T and PPI-1U Indicators.
The ASI-174 includes three test cables required for proper operation.
DescriptionRadar Test Pattern Generator (PPT-1CG)Radar Test Pattern Generator AdapterTCAS PPT Adapter Test Panel (AIT-4A)
DescriptionCable: ASI-174 PWR (W101)Cable: ASI-174 to PPI-1L/-1N/-1T (W102)Cable: ASI-174 to PPI-1P/-1U (W103 )
OEM PN2038283-05012038284-05012038816-0501
ASI MNASI-17-4AASI-17-4BASI-17-4C
Equipment Supplied:OEM PN2041323-01012039597-05018074503-0401
ASI MNASI-197ASI-198ASI-743
Power Requirements: 115 VAC 400 Hz
Optional Equipment:
PPI-1LPPI-1NPP1-1PPPI-1TPPI-1U
Specifications:Height: 8.75" Width: 19.00" Depth: 9.00"
Units Tested:
ASI-174Radar Indicator Test Panel
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: PPT-1BPart Number: 2038141-0501Manual: I.B. 1102DT / 34-42-54Manual Figure: 1
Description:
OEM Equivalent:
DescriptionCable, ASI-173 to PPI-1( ) (W1)Cable, ASI-173 PWR (W2)
OEM PNNPNNPN
ASI MNASI-17-3AASI-17-3B
RADAR INDICATOR TEST PANEL
RADAR INDICATOR TEST PANEL
TRIGGERSYNCHRO EZ
POWER
VIDEO
HIGH VOLTAGE
ASI-173
ASI-174
OFF 2 AMP2 AMP200
2 AMP OFF 3/8 AMP
NOISEADJ
9030
PRF400VIDEO
MODE SELECTOR
OFF ONSTBY
0
10
120V ARIAC
110
20 100
7050
40 80
400 Hz ADJUST
60
OFF
DELAYADJ
NOISEBURST
OFF
27.5 VDC
MOTORDRIVE
ADJUSTON 115 VAC 400
METER SELECTOROFF OFF OFF
STC SIGNAL
115 VAC400
27.5 VDC
MOTOR VOLTS0-10 VAC F.S.
-250 VDC
115V 400HzVIDEOTRG TV
ZERO SETTV STANDBY OFF OFF
27.5 VDC
MTR SEL
OFF
NORMNORM ONVIDEO
ADJ STCNOISE
BURST
90 VIDEO
NOISEADJVIDEO
27.5 VDC115 VAC SWEEP
TEST TEST
EXT MTR
18 VAC
OFF
300 VDC140 VDC
EXT MTR
ON
NOMINAL
NOMINAL
V ARIAC0 120
10 110
0DELAY
20 100
IND SEL
CONTOUR
30 90
40 80 IP / IUILIN / IT
6050 70
400 Hz ADJUST
1820 20
6 108 124 14 16
8
24
0
6 1618
20
1210 14
A i i S i li t I 3833 P i A M hi TN 38118 USA Ph 901 362 9700 F 901 794 8276 W b i i i li t
Portable Altimeter Test Set ASI-175
OEM PN2037120-0501
Optional Equipment:ASI MNASI-199
DescriptionRadio Altimeter Test Panel (ALT-51A)
Units Tested:ALA-51A
Description:The ASI-175 Portable Altimeter Test Set facilitates rapid testing for various functions of the Bendix ALA-51A altimeter. The Test Set is portable and may be used on the bench or in the aircraft.
The ASI-175 connects to the test plug on the front of the altimeter and quickly evaluates performance of the altimeter by monitoring and interpreting the outputs of various test points. The ASI-175 measures major power supply voltages and overall monitor performance by fault simulation. The Test Set also provides a swept altitude signal to check the operation of the altitude trips, it can initiate the test function, and provides the capability for checking the operation of the ground proximity warning system.
The Test Set is compact, lightweight, and enclosed in a sturdy plastic case. All power required to run the ASI-175 is supplied from the uut.
OEM Equivalent:OEM: BendixModel Number: AMT-51APart Number: 2037028-5103Manual: I.B. 1151TManual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R2
Equipment Supplied:
Depth: 4.00"Power Requirements: From UUT
Specifications:Height: 8.00" Width: 8.50"
The ASI-175-2 Altimeter Test Set is designed to facilitate the rapid testing of the various functions of the Bendix ALA-52A Radio Altimeter. The Test Set is portable and may be used either on the test bench or inside the aircraft.
The ASI-175-2 is capable of injecting simulated altitude frequencies into three altimeters simultaneously. The modulating frequencies (145,150, and 155 Hz) of the three altimeters can then be checked individually. The ASI-175-2 is also capable of simulating various rates of aircraft descent.
The ASI-175-2 receives the ARINC 429 altitude words from the altimeter under test and displays decoded altitude, along with the 429 word label and status. The Test Set can be set to read and decode either the binary or BCD 429 word from the altimeter. A functional self-test of the altimeter can be initiated at the test set. Built-in test equipment (BITE) results are displayed on the front panel annunciator.
DescriptionDescriptionOEM PNASI MNEquipment Supplied:
OEM PNASI MN
Power Requirements: From UUT
Optional Equipment:
ALA-52A
Specifications:Height: 8.00" Width: 8.50" Depth: 4.00"
Units Tested:
ASI-175-2Portable Altimeter Test Set
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: AMT-52A Part Number: 2041595-5201Manual: I.B. 1152BT / 34-42-01Manual Figure: 1
Description:
OEM Equivalent:
DescriptionTest Procedure Placard
OEM PN2034175-0002
ASI MNASI-17-5A
NORM
GOOD - NORMALFAIL - FAILNOCD - NO COMPUTER DATAFIST - TESTFTI - TEST
0 - NO FAULT1 - BITE2 - INTERFACE3 - ALT PROC4 - NON PROC5 - MODULATOR6 - CALIBRATION7 - TRACK FLTR
ALTITUDE
SELECT
BIN
BCD
8 - PLL TRACKER9 - TRANSMITTERA - MICROWAVEB - POWER SUPPLYC - ANTENNAD - IND ICATORE - PROGRAM PINSF - SELT TEST FAIL
NBCD - NO BCD DATANBIN - NO BIN DATAFFFF - NO DATAPRTY - PARITY ERRORLABL - LABEL ERROR
ASI-175-2ALTIMETER TEST PANEL
NORM
TEST
NORM NORM
FAIL NOCDMOD
FREQSYS
RAMP3
4
5
6
7ALT SEL
1
2
3
1 2
429 STATUS CODES
STATUS
FAIL CODES
LABEL CODES
2E BIN (164)AE BCD (165
BITE CODES
BUS 2
LABEL BITEALTITUDE 429BUS 1
4000 FPM
2000 FPM
METER SWITCH
TRIP SETTING
2
ASI-175
WARN
1
GPWSFLAG
TRIPS
GPWS
OFF
FLAG MONITOR
8
75 6
1
2
TRIP MONITOR
ALARM
73 4 5
2
1
6
53 4 76
T
AUXA/P
26 VAC
+35SYN
VOLTS+25
VOLTAGE MONITOR
-28
SYSTEM
S
TE#1
SWITCH
#2
10 40
0
20 30
DC MICROAMPERES
50
ASI-175
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
VHF Navigation Receiver Test Panel ASI-177-1
OEM PN2037543-05012037550-05012037553-0501MS3106F22-13SMS3106F14-6SDDM-50SMS3106F20-27S
Equipment Supplied:ASI MNASI-17-7AASI-17-7BASI-17-7NASI-17-7P16ASI-17-7P5ASI-17-7P6ASI-17-7P4
DescriptionRNA Test Cable (W105)Resolver/Synchro Calibration Cable (W109)Dummy Load Plug Assy (PR1)ASI-177-1 Power PlugASI-177-1 Remote Heading Synchro PlugASI-177-1 Remote OBS or Omni-Mag PlugASI-177-1 Remote RMI Plug
Description:The ASI-177-1 is designed to facilitate complete alignment, testing, and troubleshooting, of the Bendix RNA-26C and RNA-34A VHF Navigation Receivers.
The ASI-177-1 contains all of the necessary controls, switches, synchros, and wiring to simulate a single system installation. Meters and load resistors provide correct loading and accurate readout of the VOR/LOC and GS instrumentation outputs. Optional equipment and RNA-26C module extender cables are listed below.
OEM Equivalent:OEM: BendixModel Number: RNT-26A Part Number: 2064139-0501 Manual: I.B. 1126TManual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R2
Optional Equipment:ASI MNASI-17-7CASI-17-7DASI-17-7EASI-17-7FASI-17-7GASI-17-7HASI-17-7IASI-17-7JASI-17-7KASI-17-7LASI-17-7MASI-413-2ASI-420-1ASI-420-2ASI-424-2ASI-502
OEM PN2037551-05012037547-05012037549-05012037544-05012037546-05012037545-05012037552-05012037551-05022037548-05012037159-05012037159-05022070776-32012041341-34013614307-34012070810-3301NPN
DescriptionVHF Receiver Module RF Extender (W110)VHF Receiver Module Extender (W111)Power Supply Extender (W112)LOC Module Extender (W113)GS and LOC Monitor Module Ext (W114)ILS Check Module Extender (W115)RMI Servo Amp Module Extender (W116)GS Receiver Module RF Extender (W117)GS Receiver Module Extender (W118)LOC Dummy Load Assy (A2)GS Dummy Load Assy (A3)ILS Audio Generator (RIT-32A)RNA-34A Adapter Panel (RNT-34A)RNA-34AF Adapter Panel (ADT-34AF)VOR Audio Generator (RVG-33A)VOR Omnibearing Reader (Control Wizard)
The ASI-177-2 VOR/ILS System Test Panel is a multi-function test panel used for testing and aligning airborne navigation receiver systems (AN/ARN-123 and AN/ARN-127). Interface connection facilities are provided for a navigation receiver, remote frequency control unit, and supporting test equipment including VOR and ILS audio generators, and RF signal generator. The test panel contains al the necessary controls, switches, synchros, and wiring to simulate a single system installation.
An integral frequency control unit is included for testing and aligning receivers without their associated control units. All VOR, LOC, GS and MB receiver outputs are accurately measured using precision meters and other high-quality indicators.
DescriptionReceiver (R-2023 / R-2139) Test CableControl (C-10048 / C-10049) Test CableILS Audio Generator (RIG-32A)VOR Audio Generator (RVG-33A)
OEM PNNPNNPN2070776-32012070810-3301
ASI MNASI-17-72GASI-17-72HASI-413-2ASI-424-2
Optional Equipment:
Equipment Supplied:
ASI-177-2VOR/ILS System Test Panel
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: RNT-260A Part Number: 3604031-0501Manual: TO33D7-36-34-1 Manual Figure: 1-1
Description:
OEM Equivalent:
DEV N MTRS HUNT
108
NULL IND
V OR/LOCA NT
GSA NT
OFF
GS 27.5 VDC
A C V TVM
FIXED
LOADS ELECT
V ARIABLE
COURSES ELE CTOR MONITOR
LOAD ADJ
Y EL / DN
EXTINT
RMI AMPLS ELE CTOR
B LU / UP
ILS TEST
ZERO
.05 MC
AOMV
RMI HEADING SOURCE
OBS COURSE
B
REF P HASE
FLAG METERS ELE CTOR
.00 MC
FREQ
16 VDC 110
109
TEST
FREQDIODE
2 A MP3 A MP1 A MP
GSFLAG
DIODE GNDV ORLOC
OFF
V OR/LOC 27.5 VDC
B P-40
S HORTTEST
B P-39
OFF
115 VAC 400 Hz
TESTTEST
ILSE NERGIZE
RECEIVE R FUNCTION
NAVDISABLE
S IN
OBS COURSE SEL
HIRNAV
TEST
ASI-177-1VHF NAV RCVR
TEST PANELV OR CHECK
OFF
FUNCTIONS ELE CTOR
LOCOSHILO
GSV OR/LOC
INDICATORS ELE CTOR
E RROR METER
0
OBS COURSE
10 350
1 9.50
DAMPING
117MC DEC.00
115
116
.20
.10
RE MOTE RMI.90
V OR BEA RING
.70
.80
INT/E XTINTEXT
E RROR METERRANGE SET
E RROR METERS ELE CTOR
100
111
150
A UDIOOUTPUT
RMI
GS26V
26 V
A UTOP ILOT
27.5 VDC
SUPERFLAGV OR
E XT METER
0 NOMINAL
396
15
12
V OLTMETER
150DCMICROAMPERES
B AL TEST
TO/FROM
FREQUENCY SELECT
112 113
114
.40 .50
.30 .60
25°
2.5°
V OR B EA RING ERROR
DCMICROAMPERES
50 0 50100 3
2
COURSE DEV IATION TO
3
11 +- 0
2
A MB IGUITY FROM
ASI MNASI-17-72AASI-17-72BASI-17-72CASI-17-72DASI-17-72EASI-17-72F
OEM PN3604050-05013604049-05013604380-05013604357-05013604357-05023604357-0503
DescriptionReceiver (R-2032) Test Cable (W12)Control Unit Test Cable (W11)Power Cable (W13)GS Coax CableVOR/LOC Coax CableMB Coax Cable
.10DCMILLAMPERES
S YS TE M POWER
FREQ SE LECTORE XTERNAL
INTE RNAL
RFINP UT GSV OR LOCOUTPUT
0 DE GREE NOMINAL
MODULATION
COMPA SS HEADINGOBS DIAL
LOADMAX IMUM
MKR
2A OFF
26 V AC 400 Hz
OFF
A UDIO
FUNCTION
MKRGS
V ORLOCASI-177-2
VOR/ILS SYSTEMTEST PANEL
26 VAC400 Hz
GS FLAG
27.5 VDC
V OR/LOC FLAG
CN/MK R VOLOFF
CN ON/OFFP US H TO TEST
MKR A UDIO
NAV A UDIO
CN/NAV VOL
NOMINAL METER S ELECTOR
OMNI BE ARING SE LECTOR
010
01
350
9.5
115 VAC 400 Hz
2A OFF
27.5 VDC
1A
MAIN POWER
V OR/MKR TESTNAV DISABLE
.70.20
.90.00
.10 .80
FRA CTIONA L MHz
.40
.30
.50
.60
108
109
117
116
112
110
111
115
114
113
WHOLE MHz
DCMICROAMPERES
150150
0
.2.4 .6
.8
NOMINAL METER
E XTE RNA L METER
400 Hz 1300 Hz 3000 Hz
MARKE R BE ACON RADIO MAGNE TIC INDICA TOR
300
200
DCMICROAMPERES
300
1000- +100
200
A MB IGUITY
100
050
100
50
DEV IA TION
E
D
C
ILS
B
A
FREQUENCY ANDWIRE S S ELE CTED
Power Requirements: 115 VAC 400 Hz / 28 VDCHeight: 17.50"
Specifications:Depth: 14.00"Width: 19.00"
Units Tested:RNA-26C
Power Requirements: 115 VAC 400 HzHeight: 17.50"
Specifications:Width: 19.00"
AN/ARN-123 (R-2023 / R-2139 / C-10048 / C-10049)AN/ARN-127 (R-2032 / C-10124 / C-10125 / C-10218 / C-10490)
Units Tested:
RNA-26CF RNA-34A RNA-34AF
Depth: 14.00"
A i i S i li t I 3833 P i A M hi TN 38118 USA Ph 901 362 9700 F 901 794 8276 W b i i i li t
Radar Test Pattern Generator ASI-197
OEM PN2038141-05012039597-05012041589-04012041591-0401
Optional Equipment:ASI MNASI-174ASI-198ASI-742ASI-760
DescriptionRadar Indicator Test Panel (PPT-1B)Radar Test Pattern Generator AdapterRadar System Test Panel (RCT-4A)Radar Indicator Test Panel (PPT-4A)
Units Tested:PPI-1TPPI-1UPPI-1U(C)PPI-4B
Description:The ASI-197 Radar Test Pattern Generator provides test patterns and color select signals required during testing of the PPI-1T, PPI-1U, and PPI-4B Radar Indicators. Testing of the PPI-1U requires the optional ASI-198 Radar Test Pattern Generator Adapter.
The ASI-197 generates crosshatch, color bars and solid color pattern test signals. The crosshatch and solid patterns can be displayed in any of four colors (Blue, Green, Yellow, Red). The color bar pattern displays all four colors simultaneously.
The ASI-197 also includes Mod 3 which allows testing of TCAS modified PPI-( ) Radar Indicators.
OEM Equivalent:OEM: BendixModel Number: PPT-1CGPart Number: 2041323-0101 Manual: I.B. 1102FT / 34-41-56Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R2
Equipment Supplied:
Depth: 2.00"Power Requirements: From UUT
Specifications:Height: 4.50" Width: 7.25"
The ASI-198 Radar Test Pattern Generator Adapter is designed to adapt the ASI-197 (PPT-1CG) Radar Test Pattern Generator to the Bendix PPI-1U Radar Indicator during testing.
The ASI-197 interfaces the ASI-197 (PPT-1CG) to the checklist connector (J5103) of the PPI-1U Weather Radar Indicator. The Adapter also interfaces the checklist connector to standard ARINC control format for indicators equipped with a built-in control.
DescriptionRadar Indicator Test Panel (PPT-1B)Radar Test pattern Generator (PPT-1CG)
DescriptionOEM PNASI MNEquipment Supplied:
OEM PN2038141-05012041323-0101
ASI MNASI-174ASI-197
Power Requirements: 28 VDC
Optional Equipment:
PPI-1U
Specifications:Height: 4.50" Width: 7.25" Depth: 2.00"
Units Tested:
ASI-198Radar Test Pattern Generator Adapter
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: Part Number: 2039597-0501Manual: I.B. 1101U / 34-41-23Manual Figure: 903.1 - 903.2 (TR34-27)
Description:
OEM Equivalent:
DescriptionInline Test Connector, PPI-1( )Inline Test Connector, PPI-4B
OEM PNNPNNPN
ASI MNASI-19-7AASI-19-7B
ASI-197PATTERN GENERATORTEST SET
PATTERN COLOR
ASI-198PATTERN GENERATORADAPTER
-4B
-1T/UPPI-
CROSS HATCH
CLR BARS
SOLID
OFF
YELLOWGREEN
BLUE RED
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
Radar Altimeter Test Panel ASI-199
OEM PN2037028-5103
Optional Equipment:ASI MNASI-175
DescriptionPortable Altimeter Test Set (AMT-51A)
Units Tested:ALA-51AINA-51A
Description:The ASI-199 Radio Altimeter Test Panel is designed to facilitate testing, adjustment, and troubleshooting of the Bendix ALA-51A Radio Altimeter and INA-51A/B/V Radio Altimeter Indicator.
The ASI-199 includes two main sections, a test panel (ASI-199-1) and a precision delay line (ASI-199-3). The ASI-199 includes all switching, metering, calibrated delays, attenuators, indicators and interconnecting cables required to operate and function test the ALA-51A Radio Altimeter System.
The Test Panel has provisions for connecting an INA-51 indicator under test in addition to connecting a test indicator to assist in the alignment and testing of the ALA-51A Radio Altimeter. Built in test features permit the servicing and calibration of indicators on the bench without the additional requirement of a known good ALA-51A Radio Altimeter.
The ASI-199 includes seven interconnecting test cables and two extender boards required testing for the ALA-51A and INA-51( ).
OEM Equivalent:OEM: BendixModel Number: ALT-51APart Number: 2037120-0501Manual: I.B. 1151AT-1 / 34-10-15Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R1
Equipment Supplied:
Depth: 13.00"Power Requirements: 115 VAC 400 Hz / 27.5 VDC
Specifications:Height: 21.00" Width: 19.00"
The ASI-202 ADF System Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix DFA-73, DFA-74 ADF Receivers, and the CNA-73 ADF Control.
The ASI-202 contains circuitry which simulates a loop antenna, a sense antenna, and an antenna coupler. This circuitry converts the input from a signal generator to simulate a signal at zero degrees relative bearing, causing the ADF Indicator to display a reading of zero degrees. Voltage division is provided by the simulating circuitry so that the RF input to the ADF Receiver can be read directly in microvolts per meter at the output of the RF signal generator.
A panel mounted ADF control (user supplied) provides functions not contained in the ASI-202 such as tuning, volume, function selection, band switching, manual loop control, and voice or cw selection. The ASI-202 comes equipped with an ADF Bearing Indicator and also includes three test cables (Loop, Sense, and UUT).
DescriptionCable, CNA-73CB/FC/FD (W106)Cable, CNA-73FB (W107)
DescriptionCable, DFA-73/74 (W101)Cable, Sense (W102)Cable, Loop (W103)
OEM PN2064756-05012065211-05012064754-0501
ASI MNASI-20-2AASI-20-2BASI-20-2C
Equipment Supplied:OEM PN2065171-05012065171-0502
ASI MNASI-20-2DASI-20-2E
Power Requirements: 115 VAC 400 Hz / 27.5 VDC
Optional Equipment:
DFA-73ADFA-73A-1DFA-74A
Specifications:Height: 12.25" Width: 19.00" Depth: 10.00"
Units Tested:
ASI-202ADF System Test Panel
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: DFT-73AA Part Number: 2064943-0501Manual: I.B. 1073FManual Figure: 1
Description:
OEM Equivalent:
DescriptionTest PanelDelay Line, 650 nSCable, ASI-199-1 to ALA-51A J1 (W101)Cable, ASI-199-1 Power Input (W102)Cable, ASI-199-1 to ALA-51 P1 (W103)Cable, ASI-199-1 to INA-51 P1 (W104)Cable, ASI-199-1 to INA-51 P1 (W105)Cable, ASI-199-1 to ASI-199-3 (W112)Cable, ASI-199-1 to ASI-199-3 (W114)Extender Card, NarrowExtender Card, Wide
OEM PN2037120-05012068256-07012037536-05012037533-05012037517-05012037535-05012037554-05012038137-00072038137-00082037075-05012037076-0502
ASI MNASI-199-1ASI-199-3ASI-19-9AASI-19-9BASI-19-9CASI-19-9DASI-19-9EASI-19-9GASI-19-9HASI-19-9IASI-19-9J
INA-51BINA-51V
CNA-73ACNA-73B/BBCNA-73C/CB
CNA-73DCNA-73ECNA-73FB/FC/FD
ASI-202 SDF SYSTEM TEST PANEL
CONTROL UNIT
LAMP VOLTAGE
27.5V
INA-51( ) POWER
26 VAC
4.3
FREQUENCYMETER
DETECTOROUTPUT
INTGY MON SELECTOR
SIGNALSTRENGTH
PWR & LIN
A/P AUXDC ALT
ANT COUP
FINE
120
115 VAC 400 27.5 VDCC C TEST
DRIVE DOWN1 AMP
2.5 AMP OFF
ON
2.5 AMP
ON
OFF
NORMAL
GALX-51A/IND MON
TEST
5 V
27.5 V
INDICATOR UNDER TEST
DCALTITUDE
POWER
LIGHTING
TRIP SETTING
COARSE
FLAGOFFON
20
10
0 V ARIAC
WATTMETERPHONES
OFF 2 AMP
BRIDGE NULL
NORMAL
TRACKING SELECTOR
CAL
100
110
DFA-73 LOW
HIGH
CAL
ZERO BEAT
27.5 VDC
CNA-73LOW
HIGH
ADF CONTROLTUNING
5V
35 VDC
-28 VDC
INTGY MON SELECTOR
70AID & SYSTEM MODE SELECTORS
40' AUX
NORMALTEST
40'
57'
ALT SWP
30
40
6050
40' A / P
PRECISION VM
400 ADJUST
ANT COUP & AIDATTENUATION RANGE
HI
IND UNDERTEST
CAL LOOP
IND #2 / REC
IND #1
LO
AUTOPILOT
AUXNO LOAD
AUXNORMAL
METER SELECTOR
90
80
27.5 VDC
+10 VDC
-10 VDC
AUDIO
TUNING
26 VAC
EXT MTR
8
VOLTMETER
NOMINAL
IND UNDERTEST DC ALT
20
64
10 12
1820
1416
MONITOR METER
EXT MTR
METER SELECTOR
26 VAC 400
NOMINAL
2
27.5 VDC
115 VAC400
-28 VDC
35 VDC
25 VDC
0
4 6 8 10
OFFSETOFFSET18
X1K
TESTTEST
20 10 5
ANTENNACOUP & AID
ATTENUATOR
MDAAUDIO
CROSSCONNECT
MOVEDC UP
INTGYMON
XMTR PWR
RADARCROSS SECTION
ATTENUATOR
20 10 5
X10X1
INTEGRITY MONITOR
OVRD
NORM
PWR &LIN
AP / AUXDC ALT
ANTCOUP
SIGNALSTRENGTH
LOW
NORM
20
ALARMWARNNORM
IND #2IND #1CAL
LOOP
OVRD
NORM EXT GALVO
OVRD FAIL AFCS
LOW
NORM
3020
10 0 10
DC MILLIVOLTS
2030
ASI-199 RADIO ALTIMETER TEST SET
A / P AUX DC ALT COMPARATOR
161412
TRIPS
MDA
1 2 5 876
RFINPUT
SYNCHRONULL
OFF2 AMP
DFA-73A-1
MODEL SELECTOREXTERNAL
115V 400
INTERNALBRG INDICATOR
DFA-73A
200 180 160
180°
BEARING SELECTOR
0°
90°
270°
BRG INDICATOR
DEGREE300
280
260
240
220
340320
200
140
120
100
80
60
40
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
PPI-1TB Radar Indicator Test Panel ASI-244-1
Units Tested:PPI-1TBCON-1FB
Description:The ASI-244-1 Radar Indicator Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix PPI-1TB Weather Radar Indicator and CON-1FB SKE Range Selector.
The Test Panel contains a power supply, video generator, pattern generator, color generator, and azimuth circuitry, thus eliminating the need for other system components during testing of the PPI-1TB Radar Indicator.
The ASI-244-1 includes the PPI-1TB interconnect cable (ASI-24-4A) and the CON-1FB Test Adapter (ASI-244-3).
Test panels designed to test other units of the RDR-1FB Weather Radar System are also available from Avionics Specialist, Inc. These test panels are listed in the optional equipment section below.
OEM Equivalent:OEM: BendixModel Number: PPT-1FBPart Number: 2041350-0101Manual: I.B. 1103BT-1 / 34-43-09Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R2
Equipment Supplied:
Depth: 17.00"Power Requirements: 115 VAC 400 Hz
Specifications:Height: 10.50" Width: 19.00"
ASI-244-2PPI-1TB(M) Radar Indicator Test Panel
DescriptionCable, ASI-244-1 to PPI-1TB (W101)CON-1FB Test Adapter (W102)
OEM PN2039608-05022039817-0501
ASI MNASI-24-4AASI-244-3
ASI MNASI-152-2ASI-153-2ASI-154-2
OEM PN2041351-01022038270-05022041349-0102
DescriptionRDR-1FB Radar Test Panel (RDT-1FB)ANT-1TB Radar Antenna Test Panel (ATT-1FB)RDR-1FB Radar System Test Panel (RCT-1FB)
Optional Equipment:
DescriptionCable, ASI-244-2 to PPI-1TB(M) (W101)Cable, ASI-244-4 to CON-1TB(M) (W101)CON-1TB(M) Test Adapter
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
The ASI-244-2 Radar Indicator Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix PPI-1TB(M) Weather Radar Indicator and CON-1TB(M) Ant Azimuth Control. The Test Panel contains a power supply, video generator, pattern generator, color generator, and azimuth circuitry, thus eliminating the need for other system components during testing of the PPI-1TB(M) Radar Indicator. The ASI-244-2 also contains an azimuth motor drive board which simulates the ANT-1TB(M) sector scan antenna movement. This added circuitry, in conjunction with the ASI-244-4 Test Adapter, allows testing of the CON-1TB(M) Antenna Azimuth Control.
The ASI-244-2 includes the PPI-1TB(M) interconnect cable (ASI-24-42A), CON-1TB(M) Test Adapter (ASI-244-4) and cable (ASI-24-42B).
Test panels designed to test other units of the RDR-1FB(M) Weather Radar System are also available from Avionics Specialist, Inc. These test panels are listed in the optional equipment section below.
Equipment Supplied:ASI MNASI-24-42AASI-24-42BASI-244-4
OEM PN2039608-05028056285-05018050799-0501
OEM: BendixModel Number: PPT-1FBPart Number: 2041350-0102Manual: I.B. 1103BT-1 / 34-43-09Manual Figure: 1
Description:
OEM Equivalent:
DescriptionRDR-1FB Radar Test Panel (RDT-1FB)ANT-1TB Radar Antenna Test Panel (ATT-1FB)RDR-1FB Radar System Test Panel (RCT-1FB)
OEM PN2041351-01022038270-05032041349-0102
ASI MNASI-152-2ASI-153-3ASI-154-2
Optional Equipment:
Power Requirements: 115 VAC 400 HzHeight: 10.50" Width: 19.00" Depth: 17.00"
PPI-1TBPPI-1TB(M)
Specifications:
Units Tested:CON-1TB(M)
J1
ASI-244-1
115 VAC 400 Hz
VIDEO
RADAR INDICATOR TEST PANEL
RANGE SEL
CON-1TB(M) TEST ADAPTER
115 VAC 400 Hz BLANK
VIDEO
RANGE SEL
RADAR INDICATOR TEST PANEL
ASI-244-4
ASI-244-2
SOFT START
X Y Z
ANT SYNCHRO AZ BLANK REVERSE
ANT
STC TEST ANNUNC
0.5 uS
5 uS
MFDVIDEO TRIG
OFF2A STBY0.25A MFD
NORMPOWER 27.5 VDC ON
OFF
MODE SEL
WX TEST
MAP 2MAP 1 BCN
BCN ZERO SET
ADJ WX NOISE ADJCONTOUR NORM
METER SEL
90°
0°
BA C
27.5 VDC115 VAC SWEEP
5 uS 2A OFF200 MFDSTBY0.25A
POWERMFDVIDEO TRIG 0.5 uSPRF800 NORM27.5 VDC ON
OFF
SECTOR FRAME
CONTOUR
MODE SEL
BCN
WX TEST ADJ WX
90°ZERO SET
METER SEL
0°NOISE ADJ NORM
MAP 2MAP 1 BCN
A B
27.5 VDC115 VAC SWEEP
C
9030
V ARIAC0 120
10 110
20 100
7050
40 80
60
400 Hz ADJUST
EXT
MTR
PATTERN SEL COLOR SEL
DK BLUE
BLANK RED
YELLOWNOMINAL
CLR BARSOFF
CROSS HATCHSOLID
GREENPURPLE
LT BLUEWHITE
12 146 8
20
418
20
1610
EXT
MTR
9030DK BLUE
BLANK
V ARIAC0 120
10 110 PATTERN SEL
20 100
COLOR SEL
RED
YELLOWNOMINAL
PURPLE
7050
40 80
OFF CLR BARS
SOLID CROSS HATCH
60
400 Hz ADJUST
12 146 8
GREEN
WHITE LT BLUE2
0
418
20
1610
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
Radar Control Test Panel ASI-252-1
Units Tested:CON-1RBCON-1RB(M)
Description:The ASI-252-1 Radar Control Test Panel is designed to test and troubleshoot Bendix CON-1RB/SB Radar Controls. The test panel also has functions required to test the CON-1RB(M) / CON-1SB(M) which have variable STC capability.
The Test Panel supplies the radar control with voltages required for function tests and provides a visual continuity check verifying the correct operation of the control's switches, controls, and wiring.
The ASI-252-1 includes a control test cable (ASI-15-2A) and test panel power cable (ASI-25-2B).
Test panels designed to test other units of the RDR-1FB Weather Radar System are listed in the optional equipment section below.
OEM Equivalent:OEM: BendixModel Number: COT-1FBPart Number: 2041348-0102Manual: I.B. 1103DT-1 / 34-43-11Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R2
Equipment Supplied:
Depth: 12.00"Power Requirements: 115 VAC 400 Hz
Specifications:Height: 5.25" Width: 19.00"
ASI-252-2Radar Control Test Panel
DescriptionCable, ASI-252-1 to CON-1 (W101)Cable, ASI-252-1 Power (W102)
OEM PN2041579-05022041580-0501
ASI MNASI-25-2AASI-25-2B
ASI MNASI-152-2ASI-153-2ASI-154-2ASI-244-2
OEM PN2041351-01022038270-05022041349-01022041350-0102
DescriptionRDR-1FB Radar Test Panel (RDT-1FB)ANT-1TB Radar Ant Test Panel (ATT-1FB)RDR-1FB Radar System Test Panel (RCT-1FB)PPI-1TB Radar Indicator Test Panel (PPT-1FB)
Optional Equipment:
The ASI-252-2 Radar Control Test Panel is designed to provide the functions and capabilities necessary to test the Bendix CON-4A/B Radar Control separated from its operational environment. The test panel receives and decodes ARINC 429 control data and provides power to the CON-4( ) under test. The test panel thus substitutes its functions for those of the R/T, providing a surrogate operational environment.
The ASI-252-2 receives and decodes ARINC 429 control words 1 and 2 from the CON-4( ) and displays the decoded data on the front panel seven segment displays and LED's.
The ASI-252-2 includes two cables required for proper operation.
Test panels designed to test other units of the RDR-4A Weather Radar System are also available from Avionics Specialist, Inc. These test panels are listed in the optional equipment section below.
Specifications:
DescriptionRDR-4A Portable Radar Test Set (RST-4A)RDR-4A Radar System Test Panel (RCT-4A)PPI-4B Radar Indicator Test panel (PPT-4A)DAA-4A/B Radar Antenna Test Panel (ATT-4A)
OEM PN2041797-04012041589-04012041591-04012041592-0401
ASI MNASI-169-2ASI-742ASI-760ASI-771
DescriptionCable, ASI-252-2 to CON-4A/B (W1)Cable, ASI-252-2 Power (W8)
OEM PN2040035-05012040020-0501
ASI MNASI-25-52AASI-25-52B
Equipment Supplied: Optional Equipment:
Width: 19.00"Power Requirements: 115 VAC 400 HzHeight: 7.00" Depth: 13.00"
CON-4ACON-4B
Units Tested:
OEM: BendixModel Number: COT-4APart Number: 2041593-0401Manual: I.B. 1104ET / 34-41-59Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Description:
OEM Equivalent:
CON-1SBCON-1SB(M)
.5ASB OFF OHMS -0103 .75A1A
VOLT-OHM MONITOR
ON
115 VAC 400 Hz
VDC
PANELFAULT
LIGHTS
RT
OFF
ANT
UNIT SELALL 26 VAC
STC
TEST VOLTAGE
10 VAC
11
41 2 3
10987
5 6
LAMP TEST GAIN
RADAR CONTROLLER TEST PANEL CONTINUITY
2.5A
SYNCHRO TEST
ACVMUN-GND
5 VAC
NULLPHASE
VAC IN
ASI-252-1
RADAR CONTROL Test Panel
.5ALRUSYSTEM
STABON / OFF
POWER
28
LRU
LBLCHECK
3
DEGREES
PARITYCHECK
RATECHECKBITINT ERLOCK
PS MONITORVDC
ASI-252-2
SERIAL DATA
EXT METER
COMPTRUESYNC
-12125SYS
L - RPANELLIGHTS
REMOTEON/OFF
LAMPTEST
SDI91011
NMI
121415M ODE
16SSM
30
30
31
31
2
1CONT ROL
CONT ROL
1
2
1
TILTRANGEGAIN
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
Radar System Test Panel ASI-360
Units Tested:RDR-130 (RT-131A / AT-133A / DA-144A / IN-2026A / IN-132A / IN-152A)RDR-140 (RT-1201A / AT-143A / IN-1202A)RDR-150 (RT-131A / IN-2026A)RDR-160 (ART-161A / IN-152A / IN-2026A)RDR-1100 (RT-131A / DA-1203A / IN-2027A)RDR-1150 (RT-1151A / DA-1203A / IN-1152A/B)RDR-1200 (RT-1201A / DA-1203A / IN-1202A)RDR-1300 (RT-1301A / RT-1301B / DA-1203A / IN-2022A)RDR-1400B (RT-1401B / DA-1203A / IN-2025A)RDR-1400C (RT-1401B / DA-1203A / IN-2025B)
Description:The ASI-360 Radar System Test Panel provides a self contained means of testing the Bendix RDR-1X0/1XX0 series of Weather Radar Systems. The ASI-360 directly replaces the radar system test harness shown in the various RDR manuals.
The ASI-360 includes a gyro simulator, test points, switching, power and interconnection required to test the RDR systems.
The ASI-360 includes four interface cables required to interconnect the RT, Antenna, and Indicator for testing.
OEM Equivalent:OEM: BendixModel Number: Part Number: Manual: Manual Figure: This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R2
Equipment Supplied:
Depth: 6.00Power Requirements: 115 VAC 400 Hz / 27.5 VDC
Specifications:Height: 7.00" Width: 19.00"
ASI-1207ARadar Test Set
DescriptionCable, ASI-360 to RTCable, ASI-360 to AntennaCable, ASI-360 to IndicatorCable, ASI-360 to Indicator (Multifunction)
OEM PNNPNNPNNPNNPN
ASI MNASI-36-0AASI-36-0BASI-36-0CASI-36-0D
ASI MNASI-36-0EASI-1207A
OEM PNNPN4000595-0701
DescriptionCable, ASI-360 to ART-161ARadar Test Set (TS-1207A)
Optional Equipment:
The ASI-1207A Radar Test Set is a portable test unit designed to interface with the Bendix RT-1201/1301/1401 Receiver Transmitter.
The Test Set cable plugs into the R/T ATE connector. A function switch selects the input parameters to the test set meter for monitoring purposes. Functions monitored include crystal currents and +20 VDC power supply. The analog video output of the receiver is also available at the BNC connector located on the top of the test set. This analog video output is always available and is independent of the function selector switch position.
Specifications:
DescriptionRDR Radar System Test Panel
OEM PNNPN
ASI MNASI-360
DescriptionOEM PNASI MNEquipment Supplied: Optional Equipment:
Width: 2.25"Power Requirements: From UUTHeight: 5.00" Depth: 2.25"
RT-1201ART-1301A / RT-1301BRT-1401A / RT-1401B
Units Tested:
OEM: BendixModel Number: TS-1207APart Number: 4000595-0701Manual: I.B. 21200A Part 4Manual Figure: 1-1, 1-2 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Description:
OEM Equivalent:
GYRO SIMULATOR
115 VAC INPUT
28 VDC INPUT
OFF
POWER
OFF
ON
ONPOWER
PITCHON
OFF
LOHI
DNPITCH
UP
REMOTE RANGEIN-2025B / IN -2025A MOD 13
12 INCH
OTHER
2AHI
H I8A
LO
LO
LOHIROLL
ON 28V
OFF
DATA 2TRIGGER DATA 1
CHECKLIST
IN-2025()IN -2022A
5V / 14V
LESS ANT
IND LIGHTING
DC GND
OFF
INC
OFF
SPARE
RADAR INDICATOR
BORESIGHT
SYS GND
AZIMUTHDRIVE
MODEDECODE 1
DEC
+7.5V
MODEDECODE 2
AZIMUTHDRIVE ±90°
RTON/OFFMONITOR
STABDISABLE
ANTENNA
ADJ
HI-15V
HIANT GAIN
COMP
MODEDECODE 3
LO
LOTILT CTL
GNDTILT ADJ
ROLL TRIM
DA-1203 REFL18 INCH
RDR RADAR SYSTEM TEST PANEL
TILT ADJONRTLT
ROLL TEST SELSYSTEM
TEST SELECTSSTCON
TEST POINTS
+12V / +15V+20V -20V HI LOIF GAIN
GNDON-OFF
R/T
LOAD
SENSE
SB
ENABLE
CHK LIST
LB
DATA
ASI-360
CLOCK
MULTI-FUNCTIONINPUTS
0 1
OFF
ASI-1207ARADAR TEST SET
+20
REVDIR AFC
DC MICROAMPERES
.2 .8.4 .6
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
ILS Receiver Test Panel ASI-413-1
Units Tested:RIA-32A
Description:The ASI-413-1 ILS Receiver Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix RIA-31A ILS Navigation Receiver.
The ASI-413-1 contains all necessary loads and switches required to simulate a single system installation required by the RIA-32A Receiver. In addition, meters and switches are provided to accurately measure all of the output voltages and currents from the RIA-32A instrumentation circuits as well as from the ATE connector.
The ASI-413-1 includes the interconnecting cable (ASI-41-31A) required for testing the RIA-32A.
OEM Equivalent:OEM: BendixModel Number: RIT-32APart Number: 2070809-3201Manual: I.B. 1132AT / 34-36-01Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R1
Equipment Supplied:
Depth: 10.50"Power Requirements: 115 VAC 400 Hz
Specifications:Height: 15.00" Width: 19.00"
ASI-413-2ILS Audio Generator
DescriptionCable, ASI-413-1 to RIA-32A (W101)
OEM PN2038683-0501
ASI MNASI-41-3A
ASI MNASI-413-2
OEM PN2070776-3201
DescriptionILS Audio Generator (RIG-32A)
Optional Equipment:
The ASI-413-2 ILS Generator is designed as a promary modulation standard to test and calibrate airborne ILS receivers including the Bendix RIA-32A and RNA-34A.
The ASI-413-2 provides the stable, precision 90 and 150 Hz tone signals required to modulate RF signal generators used for testing and alignment of airbourne ILS receivers. The design of the unit allows flexibility for interfacing with existing RF signal generators. The 90 and 150 Hz localizer and glide slope modualation signals, generated by the ASI-413-2, have a high degree of frequency and amplitude stability, which is maintained by an automatic calibration loop. Front panel switching is provided for selection of various differences in the depth of modulation (DDM) test signals for both localizer and glide slope functions.
Specifications:
DescriptionVHF Receiver Test Panel (RNT-26A)ILS Receiver Test Panel (RIT-32A)VHF Receiver Test Panel (RNT-34A)
OEM PN2064139-05012070809-32012041341-3401
ASI MNASI-177-1ASI-413-1ASI-420-1
DescriptionOEM PNASI MNEquipment Supplied: Optional Equipment:
Width: 19.00"Power Requirements: 115 VAC 400 HzHeight: 5.25" Depth: 12.00"
RIA-32ARNA-34A
Units Tested:
OEM: BendixModel Number: RIG-32APart Number: 2070776-3201Manual: I.B. 1132AT / 34-36-02Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Description:
OEM Equivalent:
AUDIO
EXT MTRAUDIO
DISABLE
ILSGS
LOC1A OFF
115V 400Hz
10K
200
AUD 500MON TESTLOCGS
2 8INSTR5V SW
FN SELRANGEMTR SEL
EXTATE115 VAC
AUDIOAFCSDEV 1
CONT
91
ATE
INSTR COMP
AFCS COMP
16V
-16V
NAVDISABLENOR
R / DNL / UP
X100NOR
X10X1
HI FLAG
LOFLAG
AFCS FLAGLO INSTR
AFCSDEV 2
H I INSTR6
7
4
3
5AFCSAGC
SENS
MON AMPL
NAV
ASI-413-1ILS RECEIVER TEST PANEL
FLAGDEV
AFCSLOLOAFCS HI H I
LOCAFCSFLAG
GSINSTRFLAG
GSINSTRFLAG
GSAFCSFLAG
V ARIAC0 120
1 00 81
90
100
30
20
11010
80
60
400Hz ADJ
40
50 70
90Hz
GSLOC
OUTPUT
150HzNORMAXPRESET
NOR150Hz
0.5A
180
OFF
POWER
FN SEL
.0875.0875
.093
.155
.310
.400
φ
MAX.093
.155
PRESET
.310
.400
1020 Hz
ILS AUDIO GENERATOR
.0455
GS LEVEL
LOCLEVEL FREQ
.0455.02270.0227
X2 FOR GSDDM90Hz 150Hz
CAL BAL
CAL
NOR BAL
90Hz
ASI-413-2
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
VHF Navigation Receiver Test Panel ASI-420-1
OEM PN2064139-05012070776-32012070810-3301
Optional Equipment:ASI MNASI-177-1ASI-413-2ASI-424-2
DescriptionVHF Receiver Test Panel (RNT-26A)ILS Audio Generator (RIT-32A)VOR Audio Generator (RVG-33A)
Units Tested:RNA-34A
Description:The ASI-420-1 VHF Navigation Test Panel works in conjunction with the ASI-177-1 (RNT-26A) in order to check the digital input/output features that are contained in the Bendix RNA-34A VHF Navigation Receiver. These features were not present in the ARINC 547 VHF receivers such as the RNA-26C. The ASI-177-1 (RNT-26A) Test Panel is used to test the basic features of the RNA-34A.
The ASI-420-1 includes three interconnect cables required to interface the two test panels to the RNA-34A.
OEM Equivalent:OEM: BendixModel Number: RNT-34A Part Number: 2041341-3401 Manual: I.B. 1134AT / 34-55-03Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R1
Equipment Supplied:ASI MNASI-42-01AASI-42-01BASI-42-01C
OEM PN2039388-05012039389-05012039446-0501
DescriptionCable, ATE (W1)Cable, RNA-34A (W2)Cable, API (W3)
Depth: 10.00"Power Requirements: 115 VAC 60 Hz
Specifications:Height: 8.75" Width: 19.00"
DescriptionVHF Receiver Test Panel (RNT-26A)
DescriptionCable: RNA-34AF (W101)
OEM PN2040968-0501
ASI MNASI-42-02A
Equipment Supplied:OEM PN2064139-0501
ASI MNASI-177-1
Power Requirements: 115 VAC 400 Hz
Optional Equipment:
RNA-34AF
Specifications:Height: 8.75" Width: 19.00" Depth: 13.00"
Units Tested:
ASI-420-2VHF Navigation Receiver Test Panel
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: ADT-34AF Part Number: 3614307-3401 Manual: I.B. 1134CT / 34-55-06Manual Figure: 1
OEM Equivalent:
The ASI-420-2 VHF Navigation Test Panel works in conjunction with the ASI-177-1 (RNT-26A) in order to check the digital input/output features that are contained in the Bendix RNA-34AF Flight Inspection VOR/ILS Receiver. These features were not present in the ARINC 547 VHF receivers such as the RNA-26C. The ASI-177-1 (RNT-26A) Test Panel is used to test the basic features of the RNA-34AF.
The ASI-420-2 includes the interconnect cable required to interface the two test panels to the RNA-34AF.
Description:
TEST ADAPTER PANEL
GS
LOC
VOR
DEVIATION
DEVIATION
FM DEV RATIO
RAD / DDM
31PTYERR 30
BIT
1 A ON
POWER
/ FREQ
/ FREQ
BEARING / FREQ
DEGREES / MHZ
31PTYERR 30
BIT
BIT 30
PTYERR 31
dBm W
AGC CONTROL
AGC CONTROL
AGC CONTROL
BIT 30
PTYERR 31
%MOD
9960 HZ REF
BIT
PTYERR 3031
%MOD/AM
90 / 150 HZ
90 / 150 HZ
30 HZ VARIABLE
SERB
FREQ TUNING2/5
PORTA
LOCVOR GS
FUNCTION
ASI-420-2
LAMPTEST
ON
OFF
POWERZ'
LAMPTEST Y'X'
HDG • RMI
REFCOSSIN
CRS • BRG
AUTO REMOTE
MANUAL
BRGRMI
API
BASCOPE
DAC METER
TUNING
NAVCMP
NAVC / T CPU MUX
A-DATA
ILS MUX
SYN MUXGSC / T
BA
LO
0.1 MHz 2 / 5
1.0 MHz 2 / 5
DAC OUT
VORPRD
PGMCYLRMI
YRMI
X
VORφ
VORRDY
SCOPE
GS PWR
5VB-SYNC
NAV AGC
GS AGC
METER
FILTERING
FAST
VHF NAVIGATION RECEIVER TEST PANEL
MANUAL
DEC INC
BENCHTEST
CRS • HDGDEGREES
FAULTANNUN
SSM31PARITY 30
SSM
LABEL 30
OFFSIDE2 / 5 OFFSIDE
DEGREESDIGITAL OMNIBEARING
ILS14
PORTTUNING
SENDONSIDESERIAL
SELFTEST
SERIAL TUNING
RECONSIDE
PARITY3231
MODIFIERS
LABEL INVALIDFREQ
ASI-420-1
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
GPW System Test Panel ASI-422
OEM PNOptional Equipment:ASI MN Description
Units Tested:GPW-83 Ground Proximity Warning SystemCPA-83APRA-83APRA-83B
Description:The ASI-422 Ground Proximity Warning System Test Panel is designed to facilitate testing and troubleshooting of the Bendix CPA-83A Computer and the PRA-83 Pressure Rate Sensor. When combined with standard commercial test equipment it provides all necessary test facilities for proper maintenance and calibration of the GPW-83 Ground Proximity Warning System.
The ASI-422 simulates an aircraft flight path at any altitude below 2600 feet. the test panel provides warning indicators that monitor the five modes of operation of the CPA-83A:1. Excessive sink-rate with respect to terrain.2. Excessive terrain closure rate.3. Descent after take off.4. Insufficient clearance, not in landing configuration.5. Deviation below glide path.Additional circuits, warning indicators, and an internal speaker monitor the visual and aural outputs of the CPA-83A.
The ASI-422 also provides primary power and altitude information to allow for functional testing of the PRA-83A/B.
The ASI-422 includes two cables required for proper operation.
OEM Equivalent:OEM: BendixModel Number: CPT-83APart Number: 2041065-8301Manual: I.B. 1183F / 34-46-07Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R1
Equipment Supplied:
Depth: 13.25"Power Requirements: 115 VAC 400 Hz
Specifications:Height: 12.25" Width: 19.00"
DescriptionCable, ASI-422 to CPA-83A (W101)Cable, ASI-422 to PRA-83A/B (W102)
OEM PNNPNNPN
ASI MNASI-42-2AASI-42-2B
The ASI-423-1 Test Panel is designed to facilitate testing, alignment, and troubleshooting of the Bendix IUA-1SB Auxiliary Interface Unit (AIU) which is part of the airborne Station Keeping Equipment (SKE).
The ASI-423-1 provides the capability to fully function test the IUA-1SB. The test set uses the IP-1374/APS-133(V) Radar Indicator (PPI-1TB) and appropriate test equipment when testing the AIU. It provides power to the AIU and test indicator, and simulates aircraft SKE input to the AIU.
the ASI-423-1 includes four test cables required for operation.
Specifications:
DescriptionRadar System Test Panel (RCT-1FB)Radar Indicator Test Panel (PPT-1FB)Control Test Panel (IUT-1MB)
OEM PN2041349-01022041350-01013614662-0101
ASI MNASI-154-2ASI-244-1ASI-423-2
DescriptionCable, ASI-423 to IUT-1TB (W4)Cable, ASI-423 to IUA-1SB (W6)Cable, ASI-423 to IUA-1SB (W7)Cable, ASI-423 to PPI-1TB (W8)
OEM PN2040661-05012040662-05012040663-05012040840-0501
ASI MNASI-42-31AASI-42-31BASI-42-31CASI-42-31D
Equipment Supplied: Optional Equipment:
Power Requirements: 115 VAC 400 HzWidth: 19.00"Height: 10.50" Depth: 15.00"
IUA-1SBUnits Tested:
AIU Test Panel ASI-423-1
OEM: BendixModel Number: IUT-1SBPart Number: 3614367-0101Manual: I.B. 1103GT / 34-41-07 / TO 33D7-50-716-2Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Description:
OEM Equivalent:
A BPATTERN
LO HINOM
OFFOFF
CTR
DOWN
+-
28V
MASTERLOST
ONONMASTERSKE
UP
RANGE CODERANGE MARKS
OFF
EXT
RADARSKE / INS
SKE
MODE
RADAR / SKE WARN
8K2K4K
16K1K
2AON
POWER
SKE 28VMFD ON
OFFOFFOFF OFFOFF
PROXWARN
ONONONCAUTIONTEST
ON
SKEDATA
ON
CROSSHATCH
IUT-1SBFAULT
AIU TEST PANEL ASI-423-1
150AVALIDASCENDLIN ALT
ML2
CLOSE RATEMLI
CPA
.5ABARORATEMON
RAD ALT
8OHM
RAD ALTHIFTMON
PRA
.25A
ON
600OHM
LO
OFF
BARO VALID
PRA VALID UUT
MV / 1000 FT
DESCEND
PRAREF V
BALRAMP
CLKMON
115V 400HZ
ON
1A
MODEL
B
A
DCGND
RAMPMON OUT VALID ATE
+12V
G / S
DEVENBL
OHMVOLT COM
VALIDADJ
OFF
28 V
LO
INHB
-12 VDC
+17 VDC
-17 VDCOFF
VOLT / OHM SEL
G / S INPUTS
BINPUT SEL
LO
HI
200
WC2
<200
LNG
BARO RATEPNI
SYSINHB
RAMPGATE
250 AC500 DC581 AC
AC BARORATE CAL
>50
MODE
RATIOALT ADJ
0000 000 0
AUTO CYCLE
ALT / RATE SET(MODE 3B)
WCI
RUNALT / RATE SET
RATE SEL
BARO RATE
RATE SEL
RADIO ALT
SELF TEST
GEARUP
FLAPSUPWC4WC3
FLAPHGT
AUDIO
MUTED
CONST
ALTINVD
LVLSEL
AUDIOWARNINVD
+5 VDCID1
+12 VDCID2
G/S DEVPN2
M3
REV
NORM
GND 28 VDC
DN
UPUP
DN
GEAR
<790 <2450<700<500DISCRETE INPUTS PRGM
INPUTSFLAP
LOGICIAMFLAPS
ASI-422GROUND PROXIMITYWARNING SYSTEMTEST PANEL
ATE OUTPUTS
M4G / SENBL
G / SWARNM2 M3
VOL
LAMPTEST
COCKPIT FCTNWARN
GPG / S
ADVSYFAILGP (F)G / S
OVRD
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.comR1
Units Tested:RVA-33A
Height: 19.25"Power Requirements: 115 VAC 400 Hz
Optional Equipment:ASI MNASI-424-2
Specifications:
OEM: BendixModel Number: RVT-33APart Number: 2070811-3301Manual: I.B. 1133AT / 34-55-01Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
Equipment Supplied:OEM PN2038692-0501
The ASI-424-1 VOR Receiver Test Panel is used for testing, aligning, and troubleshooting the Bendix RVA-33A VOR Navigation Receiver.
The ASI-424-1 contains all the necessary loads, switches, and circuitry to process the VOR input/output signals required for single system aircraft installation utilizing the RVA-33A Receiver. In addition, meters and switches are provided to accurately measure all of the output voltages and currents from the RVA-33A instrumentation circuits as well as from the ATE connector.
The ASI-424-1 includes the interface cable (ASI-42-4A) required for testing the RVA-33A.
ASI MNASI-42-4A
Description:
DescriptionCable, ASI-424-1 to RVA-33A (W101)
VOR Receiver Test Panel
OEM Equivalent:BEARING
DescriptionVOR Audio Generator (RVG-33A)
OEM PN2070810-3301
Width: 19.00" Depth: 16.00"
BEARING
OBS 2150
OBS 1
0
0
ASI-424-1VOR NAVIGATION RECEIVER
TEST PANEL
VOR TEST
PHONESDISTN MTR DME OUT
AC VTVMSCOPE
0
30
20
10
40
50
DME FLAGVALID
V ARIAC 120
6070
90
110
100
80
OFF
RCVR PWRANT
1A
NAV DSBLTEST
RCVR VOLT ADJ
AFCS FLAG
HI FLAG
MTR SEL
AUDIOREV FLAG
115V
NOMINAL
EXT MTR
HI FLAG
02
486
REV FLAG
161210 14
2018
OBS SEL
1 2
240
10
1
210
270
330
300
+-
CONT115V 400Hz
1.5A OFF
10K
BIN HI
NOR
SYNC BIN LO
LOAD TEST
HI DEV
HITO / FR
LOAD TEST
AFCS DEV
OBS SELRMI
AUDIO500
200
NCDFLAG
REV FLAG LO DEV
LOTO / FR
ODDPARITY
DGTLFLAG
HI FLAG
OFF
120
350
9.5
150
90
30
60
0
DME RNG
30 PPS
DME RATE5 PPS
5
0
1060
150
180
DVM SEL
2
1 1 4
1
ATE
4
3
56
10
9 0
11
7
8
9
X10
HI TO / FR
DVM RNG
LO DEV
HI DEV
AFCS DEV
NOR
X1
LO FLAG
EXT
ATE
LO TO / FR
X100
ASI-424-1
VOLTMETER
Optional Equipment:ASI MNASI-177-1ASI-420-1ASI-424-1
Height: 8.75"Specifications:
Power Requirements: 115 VAC 400 Hz
RVA-33ARNA-34A
Units Tested:
OEM PNEquipment Supplied:
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: RVG-33APart Number: 2070810-3301Manual: I.B. 1133BT / 34-55-02Manual Figure: 1
The ASI-424-2 VOR Audio Generator is designed to facilitate testing and adjustment of conventional airborne VOR navigation receivers including the Bendix RVA-33A and RNA-34A.
The ASI-424-2 used in conjunction with an RF signal generator supplies the standard 30 Hz variable, 9960 Hz FM, and 1020 Hz signals encountered during airborne vhf omnidirectional range (VOR) operation. These signals are provided individually and in combinations for testing purposes.
VOR Audio Generator
ASI MN
OEM Equivalent:
Description:
Description
ASI-424-2
DescriptionVHF Receiver Test Panel (RNT-26A)VHF Receiver Test Panel (RNT-34A)VOR Receiver Test Panel (RVT-33A)
OEM PN2064139-05012041341-34012070811-3301
Width: 19.00" Depth: 10.00"
LO DEMODINPUT
0.2
9960/30 EXT DEMOD
OUTPUT
SIG SEL
30Hz VAR
9960 Hz
9960/30 INT DEMOD
PHASE ADJUSTINT
0.5
DEGREES
0.10.1 00.3 0.2
0.4
180
NORM
SCOPEPOWERHI DEMOD
INPUT30HzREF
30HzVAR
LO
BALANCE
VOR ZERO
COMP/1029 Hz
1020 Hz
DEMOD INPUT
30 Hz VAR
EXT
1020 Hz 9960 HzLEVELS
METER SENS
PRESET
HI
DEV RATIOTEST
FREQ CONTROL9960/ 30Hz
0.530330
60
120
300
150210
240
270 90TO FROM
X1 X10
VOR AUDIO GENERATOR
0.40.3 0
PHASE ANGLE
0 00 81
ASI-424-2
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
Doppler Signal Generator ASI-741
OEM PN2041589-0401
Optional Equipment:ASI MNASI-742
DescriptionRadar System Test Panel (RCT-4A)
Units Tested:ARINC-708 Series Weather Radar SystemsRDR-4A Weather Radar System (RCT-4A)
Description:The ASI-741 Doppler Signal Generator works in conjunction with the ASI-742 (RCT-4A) and an IFR RDX-300B/RDX-7708B to test the Bendix RTA-4A Receiver-Transmitter. It provides quadrature modulation signals for turbulence detection testing.
The ASI-741 is designed as a test instrument for ARINC 708 (RTA-4A) series weather radar systems by providing a means of testing the turbulence detection capabilities of the radar transceiver. The ASI-741 works in conjunction with a radar test set (RDX-300B or RDX-7708B) and generates simulated weather turbulence and ground returns, which enable a reading and interpretation of the resultant data on the radar test set.
OEM Equivalent:OEM: BendixModel Number: RMT-4A Part Number: 8055325-0401 Manual: I.B. 1104HT / 34-41-62Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R3
Equipment Supplied:ASI MN OEM PN Description
Depth: 13.00"Power Requirements: 115/230 VAC 47-440 Hz
Specifications:Height: 5.25" Width: 19.00"
The ASI-742 Radar System Test Panel is used in conjunction with CON-4A/4B Controllers, PPI-4B Indicator, RTA-4A R/T, and DAA-4A Antenna Drive Unit to form and test the RDR-4A Weather Radar System.
The ASI-742 provides a central station for interconnection of the above units. The ASI-742 generates target range, pulse width and digital or analog attitude signals, and ground speed signals which are transmitted to the R/T. The signals generated by the ASI-742 simulate signals from the antenna and the aircraft. Provision has been made for mounting the CON-4A/4B directly on the front panel.
The ASI-741 can be used with the ASI-742 to test the turbulence detection of the RTA-4A R/T.
DescriptionBNC-T 150 Ohm Load SMB/BNC Adapter CableDoppler Signal Generator (RMT-4A)Radar Antenna Simulator (AST-4A)Radar Test Set (RST-4A)Radar Control Test Panel (COT-4A)
DescriptionCable: ASI-742 to PPI-4B (W1)Cable: ASI-742 to API (W2)Cable: ASI-742 to CON-4A (W3)Cable: ASI-742 to DDA-4A (W4) Cable: ASI-742 to CON-4B (W5)Cable: ASI-742 to ATE (W6)Cable: ASI-742 to RTA-4A (W7)
OEM PN2039994-05012039995-05012039996-05012039997-05012039998-05012039999-05012040000-0501
ASI MNASI-74-2AASI-74-2BASI-74-2CASI-74-2DASI-74-2EASI-74-2FASI-74-2G
Equipment Supplied:OEM PNNPNNPN8055325-04012041886-04012041793-04012041593-0401
ASI MNASI-74-2HASI-74-2JASI-741ASI-770ASI-169-2ASI-252-2
Power Requirements: 115 VAC 400 Hz
Optional Equipment:
RDR-4A Weather Radar SystemCON-4A/4BDAA-4APPI-4BRTA-4A
Specifications:Height: 8.75" Width: 19.00" Depth: 13.00"
Units Tested:
ASI-742RDR-4A Radar System Test Panel
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: RCT-4A Part Number: 2041589-0401 Manual: I.B. 1104AT / 34-41-55Manual Figure: 1
Description:
OEM Equivalent:
MODE SELECT
GROUND ELIMINATION
DOPPLER SIGNAL GENERATOR
TURBULENCEON
OFF
POWER
STROBE
TARGET STROBE
CALBW
PRF
INPUT
REF
ADJUST
I
OUTPUT
Q
ASI-741
RADAR SYSTEM Test Panel
TARGET SIMULATOR
NARROWAZ24A
2A2.5A5A
LRUPOWER
SYSTEM INTLK PPIRT LIGHTS
18B
GAIN /DRIVE30A
24B ELEV WIDE
DEPTH
ANTENNA
2
B
CONTROL DATA
DATA
1
A RT
21 3
3 WIRE OFFSIDE
18µS
EXT METER
350
MAPPOWEROFF
FAN
612
450250
NMI
KNOTS
DEGREES
TRIG6µS RF MODEXT TRIG
DEGREES
REF OSC
TRIG-1
RANGE-15 26VAC
ATTITUDE SIMULATOR
PITCHRANGE ROLL
2 WIRE
ANALOG
ONSIDE
DIGITAL
5 28
VDC VAC
15 12
BW
429 SYNC
IND
CON
CONTROL UNIT PS MONITOR
20 -20
ASI-742
051 1 0+ 01+
BUS
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
TCAS PPT Adapter Test Panel ASI-743
OEM PN2038141-05012041323-01012039597-05012041591-0401
Optional Equipment:ASI MNASI-174ASI-197ASI-198ASI-760
DescriptionRadar Indicator Test Panel (PPT-1B)Radar Test Pattern Generator (PPT-1CG)Radar Test Pattern Generator AdapterRadar Indicator Test Panel (PPT-4A)
Units Tested:PPI-1T PPI-1UPPI-4BITA-81A
Description:The ASI-743 TCAS PPT Adapter Test Panel is used in conjunction with the ASI-174 (PPT-1B) or ASI-760 (PPT-4A) to test, align, and troubleshoot TCAS modified PPI-1T, PPI-1U, and PPI-4B Weather Radar Indicators and the ITA-81A Traffic Display. The ASI-743 interfaces to existing test cable harnesses and modification to existing test panels are not required.
The ASI-743 interfaces data and video signals from the existing test panel to the PPI-1T/-1U/-4B Weather Radar Indicator being tested. The necessary operating voltages for the PPI-1T/-1U/-4B are also interfaced through the ASI-743 to the PPI's. ITA-81A operating power is supplied directly from the ASI-743.
The ASI-743's internal TCAS 429 and ACARS 429 generator modules provide the 100 kHz 32 bit serial data required for testing the PPI radar indicators and the ITA-81A.
Four cables required for interconnection and testing of the PPI-1T, PPI-1U, PPI-4B, and ITA-81A are included with the ASI-174.
OEM Equivalent:OEM: BendixModel Number: AIT-4APart Number: 8074503-0401 Manual: I.B. 1104KT / 34-41-64Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R1
Equipment Supplied:
Depth: 13.00"Power Requirements: 115 VAC 400 Hz
Specifications:Height: 7.00" Width: 19.00"
The ASI-760 Radar Indicator Test Panel is designed to test, align, and troubleshoot the PPI-4B Weather Radar Indicator without the use of an R/T or radar control (CON).
The Test Panel has the capability to receive and display ARINC 429 control words, and to generate and transmit ARINC 429 and 453 data words to the PPI-4B. The ARINC 453 words are generated from the ARINC 429 data received, or from internal circuits which can be manipulated using various front panel switches. The ASI-760 also provides and monitors power required to energize the PPI-4B being tested.
The ASI-760 can be used in conjunction with the ASI-743 (AIT-4A) to test PPI-4B Indicators with TCAS capability. An optional cable (ASI-76-0B) is also available that will enable the ASI-760 to test the CCA-4A Checklist Unit
The ASI-760 includes the PPI-4B interconnect cable.
DescriptionRadar Test Pattern Generator (PPT-1CG)TCAS PPT Adapter Test Panel (AIT-4A)Cable: ASI-760 to CCA-4A
DescriptionCable: ASI-760 to PPI-4B (W1)
OEM PN2040030-0501
ASI MNASI-76-0A
Equipment Supplied:OEM PN2041323-01018074503-04018073780-0001
ASI MNASI-197ASI-743ASI-76-0B
Power Requirements: 115 VAC 400 Hz
Optional Equipment:
PPI-4BCCA-4A
Specifications:Height: 10.50" Width: 19.00" Depth: 13.00"
Units Tested:
ASI-760Radar Indicator Test Panel
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: PPT-4A Part Number: 2041591-0401Manual: I.B. 1104DT / 34-41-58Manual Figure: 1
Description:
OEM Equivalent:
DescriptionCable, ASI-743 to PPI-1T (W1)Cable, ASI-743 to PPI-1U (W2)Cable, ASI-743 to PPI-4B (W3)Cable, ASI-743 to ITA-81A (W4)
OEM PN8072626-05028072628-05028072625-05028057438-0501
ASI MNASI-74-3AASI-74-3BASI-74-3CASI-74-3D
-31400 Hz ADJUST
DISPLAYBLANK
BANDS GREEN
RED ANTR/T CON
CONTROL-DATA ACCEPT
CONTROL
TEST
DATA
SIM
0
AUTO
13
2MODE ANNUN
FAULTSCALATT IND LABELCOOL
PANELLIGHTS
SCANDEGREES
RT -2RT -1
OFFOFF 1/2
ACAMPS
SIM
VDC125
PARITY
RADAR INDICATOR Test Panel
GAINCAL
LABELCHECK
STAB13
RADARENABLE
POWER
SYSTEM LRU 1A
IND
2
1R/T
3
1WS
RANGENMI
2
1BITS
CONT ROL
CONT ROLRATE
1
2
DEGREES
GAIN
CONTROLLER SIMULATOR
MAPTESTWX
MODE
31
31
30
30
SSM16
STABON
TURB
M ODE15 14 12
NMI
RANGE
TILTDEGREES
11 10 9SDI
INDLAMPTEST
TILT
ASI-760
EXTMETER
ENABLERDR
7060
50
40
30
20
10
0 VARIAC 140
130
120
110
100
90
80
PPI-4B / ITAPPI-1T / 1U
3 AMP
OFF
MAIN POWER
ON PWR
PPT-4A ITA POWER
OFF
ON 1 AMPPWR
INT
TCAS PPT ADAPTER Test Panel
NORMAL
EXTERNAL
EXT
ARINC 429
SELECT
BENDIX
RADAR
COLLINS
OFF
3
15
105
RANGETCAS
BELOW
ALTITUDEABOVE
ASI-743
TA ONLY
FLT LEVEL
ABSOLUTE
RELATIVE
STBY
OFF
SENSITIVITY LEVELTEST
RA / TA
+ -ITA CURRENT
PPI-1T / 1U PPI-4B / ITA
TA VALID
ANTICLUT
STABLIMIT
WSENABLE
SYSTEM LRU
-12VOLTS
METER SELECT
TURBALERT
WX
Avionics Specialist, Inc. 3833 Premier Ave. Memphis, TN 38118 USA Ph: 901-362-9700 Fax: 901-794-8276 Web: www.avionics-specialist.com
Radar Antenna Simulator Test Panel ASI-770
OEM PN2041589-0401
Optional Equipment:ASI MNASI-742
DescriptionRadar System Test Panel (RCT-4A)
Units Tested:RDR-4A Weather Radar SystemRTA-4A
Description:The ASI-770 Radar Antenna Simulator Test Panel is designed to replace the Bendix DAA-4A Antenna Drive Unit in the RDR-4A Radar System test environment
The ASI-770 simulates the motor load, mechanical response, and synchro outputs of the antenna drive unit. It responds to elevation and scan drive signals, originating at the RTA-4A Receiver- Transmitter, by feeding back simulated synchro output signals that are representative of the antenna azimuth and elevation motors.
The Test Panel also has the capability of simulating all valid ranges the the RTA-4A responds to, as well as the invalid ranges which the RTA-4A does not respond to. A warning light on the front of the panel comes on when an invalid range is selected at the ASI-770.
The ASI-770 is supplied with two cables required for interface and proper operation.
OEM Equivalent:OEM: BendixModel Number: AST-4APart Number: 2041886-0401 Manual: I.B. 1104FT / 34-41-60Manual Figure: 1 This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
R1
Equipment Supplied:
Depth: 13.00"Power Requirements: 115 VAC 400 Hz
Specifications:Height: 5.25" Width: 19.00"
The ASI-771 Radar Antenna Test Panel is designed to facilitate alignment, testing, and troubleshooting of the Bendix DAA-4A Drive Unit/REA-4( ) Planer Array Radar Antenna.
The ASI-771 contains circuitry to convert the azimuth synchro transmitter input of the DAA-4A/REA-4( ) and DAA-4B Radar Antenna into a DC signal which varies with the changing position at the antenna. This DC signal is further processed to control the azimuth drive of the radar antenna through a limited azimuth scan (approx. 120°). The ASI-771 also has the ability to vary the elevation of the antenna in tilt up or tilt down.
The ASI-771 is supplied with four cables required for interface and proper operation.
DescriptionRadar System Test Panel (RCT-4A)Radar Indicator Test Panel (PPT-4A)Radar Test Set (RST-4A)Radar Control Test Panel (COT-4A)
DescriptionCable: ASI-771 to DAA-4A (W1)Cable: ASI-771 to API (W2)Cable: ASI-771 to DAA-4B (W3)Cable: ASI-771 PWR (W8)
OEM PN2040083-05012040082-05012040981-05012040020-0501
ASI MNASI-77-1AASI-77-1BASI-77-1CASI-77-1D
Equipment Supplied:OEM PN2041589-04012041591-04012041793-04012041593-0401
ASI MNASI-742ASI-760ASI-169-2ASI-252-2
Power Requirements: 115 VAC 400 Hz
Optional Equipment:
DAA-4ADAA-4BREA-4( )
Specifications:Height: 5.25" Width: 19.00" Depth: 13.00"
Units Tested:
ASI-771Radar Antenna Test Panel
This unit is manufactured to replace the OEM MN, PN, and/or manual figure listed in Form, Fit, and Function.
OEM: BendixModel Number: ATT-4A Part Number: 2041592-0401Manual: I.B. 1104CT / 34-41-57Manual Figure: 1
Description:
OEM Equivalent:
DescriptionCable, ASI-770 to ASI-742 / RCT-4A (W101)Cable, ASI-770 PWR (W108)
OEM PN2040331-05012040020-0501
ASI MNASI-77-0AASI-77-0B
-901/2 AON
RADAR ANTENNA Test Panel
SYSTEM
1 AMPLRU
MAIN POWER
LRU
ASI-771
AZ ELEV MON
ANTENNA SIMULATOR Test PanelPOWER
0+90
SCANRANGE
ASI-770
GND+5 VDC +15 VDC -15 VDC
PS MONITOR
ALIGN - + ELEV
DISABLE
AZCW RUNELEVELEVATION
DISABLE
AZ Y ZX
INVALIDRANGE
EL DRA B
PPI
ANTENNA SCANCW CCW
1
INTERNAL
ANTENNAPOWER
SCANANGLE
05