Post on 11-Dec-2016
transcript
EN - english
Instructions for installation and operation
Replacement unit
Service-Unit BEKOMAT® 32U / 32U F(SUBM32U / SUBM32UF)
01-1
614
2 Service-Unit BEKOMAT® 32U / 32U F
Service-Unit BEKOMAT® 32U / 32U F 3
1 Pictograms and symbols ........................................................................................................................4
2 Safety instructions ..................................................................................................................................4
3 Technical data ........................................................................................................................................6
4 Control and maintenance .......................................................................................................................7
5 Elements and components...................................................................................................................10
6 Recommended spare parts..................................................................................................................11
Pictograms and symbols
4 Service-Unit BEKOMAT® 32U / 32U F
Pos: 1 /Beko Technische Dokumentati on/Ü berschriften/1/Pi ktogramme und Symbol e @ 1\mod_1290773595840_2901.docx @ 20524 @ 1 @ 1
1 Pictograms and symbolsPos: 2 /Beko Technische Dokumentati on/Pi ktogramme/Anl eitung beachten blau @ 0\mod_1213268300255_2901.docx @ 8336 @ @ 1
Observe the installation and operating instructions
Pos: 3 /Beko Technische Dokumentati on/Pi ktogramme/Anl eitung beachten s/w Typenschild @ 1\mod_1290772180142_2901.docx @ 20491 @ @ 1
Observe the installation and operating instructions(on the type plate)
Pos: 4 /Beko Technische Dokumentati on/Pi ktogramme/Gefahr Warnung Vorsicht s/w @ 0\mod_1213265685174_2901.docx @ 8260 @ @ 1
General danger symbol (danger, warning, caution)
Pos: 5 /Beko Technische Dokumentati on/Pi ktogramme/G+W+ V N etzspannung s /w @ 0\mod_1213266193701_2901.docx @ 8298 @ @ 1
General danger symbol (danger, warning, caution) for supply voltage and supplyvoltage-carrying plant components
Pos: 6 /Beko Technische Dokumentati on/Ü berschriften/1/Sicherheitshinweise @ 0\mod_1183637609261_2901.docx @ 5367 @ 1 @ 1
2 Safety instructionsPos: 7 /Beko Technische Dokumentati on/Sicherheit/Hi nweis Anlei tung BEKO ( männl. N ame) @ 0\mod_1184147787557_2901.docx @ 5760 @ @ 1
Please check whether or not these instructions correspond to the device type.
Adhere to all advice given in these operating instructions. They include essential informationwhich must be observed during the installation, operation and maintenance. Therefore it isimperative for the service technician and the responsible operator / technical staff to read theseoperating instructions prior to installation, start-up and maintenance.
The operating instructions must be accessible at any time at the place of application of theBEKOMAT® 32U .
In addition to these operating instructions, local or national regulations must be complied with,if necessary.
Make sure that the BEKOMAT® 32U is operated only within the permissible limit valuesindicated on the type plate. Any deviation involves a risk for persons and materials, and mayresult in malfunction and service failures.
If you have any queries regarding these installation- and operating instructions, please contactBEKO TECHNOLOGIES GMBH.
Pos: 8 /Beko Technische Dokumentati on/Sicherheit/Gefahr Druckluft @ 0\mod_1184148143854_2901.docx @ 5778 @ @ 1
Danger!
Compressed air!
Risk of serious injury or death through contact with quickly or suddenly escapingcompressed air or through bursting plant components or plant components which arenot secured.
Pos: 9 /Beko Technische Dokumentati on/Sicherheit/M aßnahmen Dr uckl uft BM @ 0\mod_1184148284291_2901.docx @ 5814 @ @ 1
Measures:
• Do not exceed the maximum operating pressure (see type plate).
• Only carry out service measures when the system is pressureless.
• Use pressure-resistant installation material only.
• The feed pipe must be tubed firmly. Discharge pipe: short, fixed pressure hose onto pressure-resistantpipe.
• Make sure that persons or objects cannot be hit by condensate or escaping compressed air.
Pos: 10 /Beko Technische D okumentati on/Sicher hei t/Gefahr Netzspannung 1 s/w @ 0\mod_1184148186948_2901.docx @ 5796 @ @ 1
Safety instructions
Service-Unit BEKOMAT® 32U / 32U F 5
Danger!
Supply voltage!
There is the risk of an electric shock involving injury or death when coming into contactwith non-insulated components carrying supply voltage.
Pos: 11 /Beko Technische D okumentati on/Sicher hei t/Maßnahmen N etzspannung BM 31U/32U/33U @ 7\mod_1390467197804_2901.docx @ 38043 @ @ 1
Measures:
• During electric installations, all regulations in force need to be adhered to (e.g. VDE 0100 / IEC 60364).
• When the control unit is open, service and installation works must only be undertaken when thesystem is deactivated.
• The removed control unit has no IP degree of protection.
• All types of electrical works must be carried out by authorised and qualified personnel only.
Pos: 12 /Beko Technische D okumentati on/Sicher hei t/Sicherheitshinweise, weitere BM ( nicht Ex, nicht IF) @ 0\mod_1183616103770_2901.docx @ 4011 @ @ 1
Further safety instructions:
• For installation and operation, the national regulations and safety codes in force must also be adheredto.
• Do not use the BEKOMAT® 32U in hazardous areas.
• Regarding the inlet screw joints, excessive tightening forces must be avoided. This applies in particularto conical screw joints.
• The BEKOMAT® 32U will only function when voltage is applied.
• Do not use the test button for permanent drainage.
• Use genuine spare parts only. This is imperative to ensure perfect functioning.Pos: 13 /Beko Technische D okumentati on/Sicher hei t/Zusatz Sicherheitshi nweise BM31/32 SA + 31U /32U SA @ 0\mod_1185351496993_2901.docx@ 6480 @ @ 1
Additional advice:
• The removed control unit has no IP degree of protection.
• During installation, use spanner flat at the feed pipe (wrenchsize SW27) as a back rest.
• The service unit must not be dismantled.
Pos: 14 /Beko Technische D okumentati on/Sicher hei t/Vorsicht Fehlfunktion @ 0\mod_1214378096290_2901.docx @ 9360 @ @ 1
Caution!
Malfunction during operation!
Through incorrect installation and poor maintenance, malfunction may occur at theBEKOMAT .
Condensate which is not discharged may cause damage to plants and in productionprocesses.
Pos: 15 /Beko Technische D okumentati on/Sicher hei t/Maßnahmen Fehl funkti onen BM @ 0\mod_1214378434025_2901.docx@ 9379 @ @ 1r
Measures:
• Condensate drainage which is reliable in performance directly optimises the compressed-air quality.
• To prevent damage and breakdowns, it is imperative to observe the following:
• Exact compliance with the specifications of use and with the performance parameters of theBEKOMAT, in connection with the case of application (see "Proper use" section)
• Exact compliance with the installation- and operation instructions in this manual
• Regular maintenance and control of the BEKOMAT in accordance with the instructions in thisoperating manual
Pos: 16 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.docx @ 2903 @ @ 1
Technical data
6 Service-Unit BEKOMAT® 32U / 32U F
Pos: 17 /Beko Technische D okumentati on/Überschriften/1/Techni sche D aten @ 0\mod_1184329570967_2901.docx @ 6058 @ 1 @ 1
3 Technical dataPos: 18 /Beko Technische D okumentati on/Technische D aten/BEKOM AT/Techn. D aten BM 3xU + UC + GOST (o.Leistg.) @ 5\mod_1358843578945_2901.docx @ 30450 @ @ 1
min./max. operating pressure(see type plate)
0,8...16 bar (12...230 psi)or1,2...16 bar (17...230 psi)
min./max. temperature(see type plate)
+1...+60 °C (+34...+140 °F)or+1...+70 °C (+34...+158 °F)
Condensate inflowG ½ (NPT ½) internalmax. screw-in depth 13,5 mm (½")
Condensate outflow G ¼ Ø 8 ... 10 mm hose connector
Condensate oil-contaminated + oil-free
Housing aluminium + plastic, glass fibre-reinforced
Weight (empty) 0,5 kg (1.1 lbs)
Pos: 19 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.docx @ 2903 @ @ 1
Control and maintenance
Service-Unit BEKOMAT® 32U / 32U F 7
Pos: 20 /Beko Technische D okumentati on/Überschriften/1/Kontr olle und Wartung @ 0\mod_1183637885371_2901.docx @ 5439 @ 1 @ 1
4 Control and maintenancePos: 21 /Beko Technische D okumentati on/Sicher hei t/Gefahr Druckl uft @ 0\mod_1184148143854_2901.docx @ 5778 @ @ 1
Danger!
Compressed air!
Risk of serious injury or death through contact with quickly or suddenly escapingcompressed air or through bursting plant components or plant components which arenot secured.
Pos: 22 /Beko Technische D okumentati on/Sicher hei t/Maßnahmen Druckluft BM @ 0\mod_1184148284291_2901.docx @ 5814 @ @ 1
Measures:
• Do not exceed the maximum operating pressure (see type plate).
• Only carry out service measures when the system is pressureless.
• Use pressure-resistant installation material only.
• The feed pipe must be tubed firmly. Discharge pipe: short, fixed pressure hose onto pressure-resistantpipe.
• Make sure that persons or objects cannot be hit by condensate or escaping compressed air.
Pos: 23 /Beko Technische D okumentati on/Sicher hei t/Gefahr Netzspannung 1 s/w @ 0\mod_1184148186948_2901.docx @ 5796 @ @ 1
Danger!
Supply voltage!
There is the risk of an electric shock involving injury or death when coming into contactwith non-insulated components carrying supply voltage.
Pos: 24 /Beko Technische D okumentati on/Sicher hei t/Maßnahmen N etzspannung BM 31U/32U/33U @ 7\mod_1390467197804_2901.docx @ 38043 @ @ 1
Measures:
• During electric installations, all regulations in force need to be adhered to (e.g. VDE 0100 / IEC 60364).
• When the control unit is open, service and installation works must only be undertaken when thesystem is deactivated.
• The removed control unit has no IP degree of protection.
• All types of electrical works must be carried out by authorised and qualified personnel only.
Pos: 25 /Beko Technische D okumentati on/Sicher hei t/Vorsicht Fehlfunktion @ 0\mod_1214378096290_2901.docx @ 9360 @ @ 1
Caution!
Malfunction during operation!
Through incorrect installation and poor maintenance, malfunction may occur at theBEKOMAT .
Condensate which is not discharged may cause damage to plants and in productionprocesses.
Pos: 26 /Beko Technische D okumentati on/Sicher hei t/Maßnahmen Fehl funkti onen BM @ 0\mod_1214378434025_2901.docx@ 9379 @ @ 1r
Measures:
• Condensate drainage which is reliable in performance directly optimises the compressed-air quality.
• To prevent damage and breakdowns, it is imperative to observe the following:
• Exact compliance with the specifications of use and with the performance parameters of theBEKOMAT, in connection with the case of application (see "Proper use" section)
• Exact compliance with the installation- and operation instructions in this manual
• Regular maintenance and control of the BEKOMAT in accordance with the instructions in thisoperating manual
Control and maintenance
8 Service-Unit BEKOMAT® 32U / 32U F
Pos: 27 /Beko Technische D okumentati on/Sicher hei t/Hinweis Vorschrif ten Wer kzeug R einigung Kondensat Entsorgung @ 0\mod_1233239666823_2901.docx @ 13340 @ @ 1
Note:
It is imperative to observe all hazard statements and warnings listed here.
Please also observe all regulations and notes regarding industrial safety and fire prevention at the place ofinstallation.
As a matter of principle, only use suitable and appropriate tools and materials in a proper condition.
Do not use aggressive cleaners and improper devices such as high-pressure cleaners.
Please note that condensates may contain aggressive or harmful components. Therefore, skin contactshould be avoided.
Condensate is subject to mandatory waste disposal. As such, it must be collected in suitable containers, anddisposed of or processed properly.
Pos: 28 /Beko Technische D okumentati on/Wartung/BEKOM AT/Wartung BM 31U /Wartung BM 31U/32U Ser vice-U nit @ 5\mod_1358510276825_2901.docx @ 30412 @ @ 1
1. Prior to the replacement of the service unit, a resetneeds to be carried out.The control unit is released by actuating thearresting hook.When removed, the TEST button below the LEDmust be pressed and held for at least five seconds.
2. Unfasten the BEKOMAT® 32U from the outlet (3).
3. Detach the service unit (5) from the tubing at theinlet.
Missing numbers are constituents of the BEKOMATstand-alone model.
Control and maintenance
Service-Unit BEKOMAT® 32U / 32U F 9
Control unit with cordpacking
(previous version)
Control unit withoutcord packing
(current version)
Prior to placing a previous version of the controlunit with cord packing (17) in the lower part of thecover, the sealing mat (11) must be removed fromthe service unit.
Installation of the control unit on the service unit:
1. Check whether or not the service unit (5) goes withthe control unit (1) (model designation and colourof the arresting hook).
2. Check whether or not the sealing mat (11) or thesensor tube plate (14) with contact springs (13) areclean, dry, and free from impurities.
3. Introduce the sensor (12) into the sensor tube plate(14).
4. Hang the hook (15) of the control unit (1) in thesensor tube plate (14).
5. Press the control unit (1) against the service unit(5) and snap into place.
Start-up subsequent to maintenance measures:
Always carry out prior to the start-up:
• Leak test of the screwed connector
• Check of the electrical connections
• Check of the correct engagement of the control unit
Pos: 29 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.docx @ 2903 @ @ 1
12
15
1
11
13
14
5
17
Elements and components
10 Service-Unit BEKOMAT® 32U / 32U F
Pos: 30 /Beko Technische D okumentati on/Überschriften/1/Bauteile und Komponenten @ 0\mod_1183638014355_2901.docx @ 5475 @ 1 @ 1
5 Elements and componentsPos: 31 /Beko Technische D okumentati on/Bauteil e und Komponenten/BEKOMAT/Bauteil e BM 32U Ser vice-U nit @ 6\mod_1378727891522_2901.docx @ 33642 @ @ 1
1 Screw 3.5 x 10
2 Upper part of the cover
3 Moulded gasket
4 Printed circuit board
5 Sensor
6 Lower part of the cover
7 Cable bushing
8 Sealing mat
9 Service unit
10 Hose connector
11 O-ring 20 x 2
12 Intermediate adapter
13 Screw M6 x 12
14 O-ring 14 x 1.78
15 Angle adapter
16 Design shell
17 Cord packing (only previous version)
Pos: 32 /---- Seitenumbr uch ---- @ 0\mod_1157028099015_0.docx @ 2903 @ @ 1
Recommended spare parts
Service-Unit BEKOMAT® 32U / 32U F 11
Pos: 33 /Beko Technische D okumentati on/Überschriften/1/Empfohl ene Ersatzteile @ 0\mod_1183638186183_2901.docx @ 5529 @ 1 @ 1
6 Recommended spare partsPos: 34 /Beko Technische D okumentati on/Ersatzteile Verbr auchsmaterialien Zubehör/BEKOMAT/Ersatz teil e BEKOM AT 32U Ser vice-Unit ( AU+FKM) @ 4\mod_1358168452791_2901.docx @ 29760 @ @ 1
Available sets of spare parts Contents Order number
Service-Unit SUBM32Ufor BM32U or BM32UBI orBM32 or BM32BI
Service-Unit SUBM32UFfor BM32UF or BM32UBIF orBM32UIFBIF or BM32F orBM32BIF or BM32IFBIF
8, 9, 11*
4023571
4025061
Gasket kit 3, 8, 11*, (17) 4024392
Design shell* 16* 4010167
Connection adapter* 11*, 12*, 13*, 14*, 15* 4010155
* Not for BEKOMAT 32U built-in or BEKOMAT 32U built-in FPos: 35 /Beko Technische D okumentati on/Globale Texte/Hinweis Ü bersetzg. d. Orig.anl eitg. @ 1\mod_1260433478358_2901.docx @ 17104 @ @ 1
Pos: 36 /Beko Technische D okumentati on/Globale Texte/Hinweis Original anl eitung @ 1\mod_1260433346280_2901.docx @ 17070 @ @ 1
Pos: 37 /Beko Technische D okumentati on/Globale Texte/Vorbehaltsklausel @ 0\mod_1213704033153_2901.docx @ 9298 @ @ 1
=== Ende der Liste für Textmar ke Inhalt ===
12 Service-Unit BEKOMAT® 32U / 32U F
A
Angle adapter 10
C
Components 10
Control 7
Control unit 9
Cord packing 10
D
Danger compressed air 4, 7
Danger supply voltage 5, 7
Data 6
Degree of protection 5, 7
E
Elements 10
H
Hose connector 10
I
Installation and operating instructions 4
Installation and operating instructions 4
Instructions, safety instructions 4
Intermediate adapter 10
L
Lower part of the cover 10
M
Maintenance 7
O
Order number 11
P
Pictograms 4
Printed circuit board 10
Q
Qualified personnel 5, 7
R
Recommended spare parts 11
S
Safety instructions 4
Sensor 10
Service measures 4, 7
Service unit 10
Sets of spare parts 11
Spare parts 5, 11
Symbols 4
T
Technical data 6
U
Upper part of the cover 10
Service-Unit BEKOMAT® 32U / 32U F 13
14 Service-Unit BEKOMAT® 32U / 32U F
Service-Unit BEKOMAT® 32U / 32U F 15
Service-Unit BEKOMAT® 32U / 32U F
Headquarter :
Deutschland / Germany
BEKO TECHNOLOGIES GMBH
Im Taubental 7
D-41468 Neuss
Tel. +49 2131 988 0
beko@beko-technologies.com
中华人民共和国 / China
BEKO TECHNOLOGIES (Shanghai)Co. Ltd.
Rm.606 Tomson Commercial Building
710 Dongfang Rd.
Pudong Shanghai China
P.C. 200122
Tel. +86 21 508 158 85
info.cn@beko-technologies.cn
France
BEKO TECHNOLOGIES S.à.r.l.
Zone Industrielle
1 rue des Frères Rémy
F- 57200 Sarreguemines
Tél. +33 387 283 800
info@beko-technologies.fr
India
BEKO COMPRESSED AIRTECHNOLOGIES Pvt. Ltd.
Plot No.43/1, CIEEP, Gandhi Nagar,
Balanagar, Hyderabad - 500 037, INDIA
Tel. +91 40 23080275
eric.purushotham@bekoindia.com
Italia / Italy
BEKO TECHNOLOGIES S.r.l
Via Peano 86/88
I - 10040 Leinì (TO)
Tel. +39 011 4500 576
info.it@beko-technologies.com
日本 / Japan
BEKO TECHNOLOGIES K.K
KEIHIN THINK 8 Floor
1-1 Minamiwatarida-machi
Kawasaki-ku, Kawasaki-shi
JP-210-0855
Tel. +81 44 328 76 01
info@beko-technologies.jp
Benelux
BEKO TECHNOLOGIES B.V.
Veenen 12
NL - 4703 RB Roosendaal
Tel. +31 165 320 300
benelux@beko-technologies.com
Polska / Poland
BEKO TECHNOLOGIES Sp. z o.o.
ul. Chłapowskiego 47
PL-02-787 Warszawa
Tel +48 22 855 30 95
info.pl@beko-technologies.pl
Scandinavia
www.beko-technologies.com
España / Spain
BEKO Tecnológica España S.L.
Torruella i Urpina 37-42, nave 6
E-08758 Cervello
Tel. +34 93 632 76 68
info.es@beko-technologies.es
South East Asia
BEKO TECHNOLOGIES S.E.Asia(Thailand) Ltd.
75/323 Romklao Road
Sansab, Minburi
Bangkok 10510
Thailand
Tel. +66 2-918-2477
info.th@beko-technologies.com
臺灣 / Taiwan
BEKO TECHNOLOGIES Co.,Ltd
16F.-5, No.79, Sec. 1,
Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221,
Taiwan (R.O.C.)
Tel. +886 2 8698 3998
peter.huang@beko-technologies.tw
Česká Republika / Czech Republic
BEKO TECHNOLOGIES s.r.o.
Na Pankraci 1062/58
CZ - 140 00 Praha 4
Tel. +420 24 14 14 717
info@beko-technologies.cz
United Kingdom
BEKO TECHNOLOGIES LTD.
2 & 3 West Court
Buntsford Park Road
Bromsgrove
GB-Worcestershire B60 3DX
Tel. +44 1527 575 778
info@beko-technologies.co.uk
USA
BEKO TECHNOLOGIES CORP.
900 Great SW Parkway
US - Atlanta, GA 30336
Tel. +1 404 924-6900
beko@bekousa.com
Translation of the original manual/instructions.
Original instructions are in German.
Subject to technical modifications without notice / errors excepted.
BM32U_F_s_unit_uc_manual_en_2014_08.