Post on 29-Jan-2021
transcript
BACHMANN INDUSTRIES, INC. 1400 East Erie AvenuePhiladelphia, Pennsylvania 19124 USA 800-356-3910 www.bachmanntrains.com Printed in China
Body Shell Assembly1:20.3 Large Scale Long Caboose
G887X-IS001
BACHMANN INDUSTRIES, INC. 1400 East Erie AvenuePhiladelphia, Pennsylvania 19124 USA 800-356-3910 www.bachmanntrains.com Printed in China
Roof & Cupola Assemblies1:20.3 Large Scale Long Caboose
G887X-IS002
Chassis Assembly1:20.3 Large Scale Long Caboose
BACHMANN INDUSTRIES, INC. 1400 East Erie AvenuePhiladelphia, Pennsylvania 19124 USA 800-356-3910 www.bachmanntrains.com Printed in China
G887X-IS001
BACHMANN INDUSTRIES, INC. 1400 East Erie AvenuePhiladelphia, Pennsylvania 19124 USA 800-356-3910 www.bachmanntrains.com Printed in China
Wiring Assembly1:20.3 Large Scale Long Caboose
G887X-IS002
3mm3mm
3mm
3mm
WHITE
GRAY
GRAY
BROWN
GREEN
BROWN
PURPLEYELLOW
ORANGE
BLACK
RED
GREEN
BLUE
BLUE
MARKED LIGHT 2
MARKED LIGHT 1
Pull up the cushion cover
Remove the dummy plug fromthe socket
Install 8 pin decoder (eitherbachmann HO decoder or otherdecoder from open market)
There are 2 switchesunder the chassisfor selection ofpick up & LEDS
How to install Decoder
BACHMANN INDUSTRIES, INC. 1400 East Erie AvenuePhiladelphia, Pennsylvania 19124 USA 800-356-3910 www.bachmanntrains.com Printed in China
DCC
Please notice that whenusing non-Bachmann decoder,switch 2 should be located atthe marker light positon otherwise it works improperly.
SWITCH 1 SWITCH 2
8 5
1 4
8 PIN SOCKET
G887X-IS003
Slide the seat cover horizontally
Lift up the seat cover withcushion
Follow the battery logo positionto install two AA batteries
How to load batteries inside the car body
BACHMANN INDUSTRIES, INC. 1400 East Erie AvenuePhiladelphia, Pennsylvania 19124 USA 800-356-3910 www.bachmanntrains.com Printed in China
- AA +
+ AA -
Batteries not included
CAUTION!- Do not mix old and new batteries or different types of batteries- Remove batteries if the product is not in use - Do not short-circuit the battery contacts
G887X-IS003
Unfasten 4 screwsat the long ladder(88797 , 88798)
Slide the roof cover backward horizontally
Pull up the roof cover
DETAIL A
DETAIL B
B
A
When assembling the roof cover, make sure the ladder is installed into the brackets on the roof end.
How to remove the roof from the body
BACHMANN INDUSTRIES, INC. 1400 East Erie AvenuePhiladelphia, Pennsylvania 19124 USA 800-356-3910 www.bachmanntrains.com Printed in China
G887X-IS004
Unfasten two screws on thecoupler box cover and thenremove the fine scale couplers
Install the offset shankcoupler with chain
Make sure the chain is fastened to the uncoupling lever before assemble the coupler.
How to change the front / reardie-cast offset shank couplers
BACHMANN INDUSTRIES, INC. 1400 East Erie AvenuePhiladelphia, Pennsylvania 19124 USA 800-356-3910 www.bachmanntrains.com Printed in China
BACHMANN INDUSTRIES, INC. 1400 East Erie AvenuePhiladelphia, Pennsylvania 19124 USA 800-356-3910 www.bachmanntrains.com Printed in China
(ACCESSORY BAG)
How to exchange LEDs on markers/table lights
G887X-IS004
Remove marker lamp / chimney
Grasp bracket whileremoving LED
How to separate the two sides of the interior walls from the body shell
BACHMANN INDUSTRIES, INC. 1400 East Erie AvenuePhiladelphia, Pennsylvania 19124 USA 800-356-3910 www.bachmanntrains.com Printed in China
G887X-IS005
Unfasten 8 screws atthe two sides of body shell
1
2 Pull up two sides of interiorwalls carefully to preventdamage to the wires insidethe interior walls
G887X-IS001-01.pdfG887X-IS001-02.pdfG887X-IS001-03.pdfG887X-IS002.pdfG887X-IS003-1.pdfG887X-IS003-2.pdfG887X-IS004-1.pdfG887X-IS004-2.pdfG887X-IS005.pdf