Post on 13-Oct-2015
transcript
HAMMER Comparison Guide
Bosch vs. Hilti
2 Boschtools.com
The World Leader in Hammers
"All Hilti information was obtained from Hilti.com on 4/1/2011."
Concrete, Brick or Asphalt Nothing Stops a Bosch Hammer. Engineered to withstand the harshest conditions or your most extreme demands, Bosch tools will provide you with more power, long after the competition gives out.
Look for the Bosch AdvantageInside this guide you will discover Bosch products compared
directly with the competition Hilti. Certain attributes of Bosch products are marked with red check marks to highlight the advantages over the competition.
With every comparison, product specifications and features are described. The Bosch products are coded according to the bit system used.
We hope this guide makes your search for the perfect tool quicker and easier. Because with Bosch Hammers youll get more power, better technology and little competition.
Table of ContentsThe Comparisons Page-by-Page
BoSCH HiLTi Pg
SDS-pluS RotaRy HammeRS
11250VSR, 11253VSR TE 2 STD 4
11255VSR, 11224VSR TE 6 S, TE 7 C 4
RH328VC, RH328VCQ TE 30 AVR 5
RH432VCQ TE 40 AVR C 5
11250VSRD TE 6S PRO, TE 7C PRO 6
11320VS 6
SDS-max RotaRy HammeRS
11240 TE 50 7
11264EVS TE 60, TE 60 ATC/AVR 7
11263EVS TE 70, TE 70 ATC 8
11245EVS TE 80 ATC/AVR 8
Spline ComBination HammeRS
11247 9
11265EVS 9
Demolition HammeRS
11321EVS TE 706, TE 706 AVR 10
11388, 11387 TE 500 10
11316EVS, 11317EVS TE 805, TE 1000 AVR 11
BReakeR HammeRS
11335K TE 1500 AVR 12
NEW Brute BH2760VCD TE 3000 AVR 12-13
HammeR HauleRS
T1757, T1657 13
HammeR CaRBiDe BitS
X5L, Rebar Cutter 14
Speed-X, Multi-Construction 15
SDS-max R-Tec 16
m e a S u R i n g & l ay o u t t o o lS
gLR225, gLR500 PD4, PD40 17
gPL2, gPL5C PMP 32, PMC 36 18
gLL2-80 PMC 46, PML 32-R 19
D-TECT 150 PS-200 19
DAF220K 20
BP350 PUA 10, 20
BT300HD, WM1, WM4 PA 911, PUA 30 PMA 78, PRA 71 21
Color-Coded Bit System
SDS-plus Bit SystemFor small and medium rotary hammers.
SDS-max Bit System For medium and large rotary hammers or demolition hammers.
For large breaker or demolition hammers.
1-1/8"Hex Collar
3/4" Hex
For medium and large rotary hammers or demolition hammers.
Round Hex
Spline
3Toll Free: 877-BOSCH-99
21
2
Vibration ControlReduce Vibration by up to 60% in two steps1 - point of origin impact mechanism2 - point of effect handle
A longer air cushion between the piston and the striker pin leads to lower pressure and thus lower vibration levels without reducing performance.
The rubber dampening elements at the top and bottom of the main handle also help reduce vibration levels.
Turbo Power Delivers 20% more power in hammer only mode.
Service Minder LightIndicates when preventative maintenance is required.
Bosch innovationsBosch vs. Hilti Comparison Guide
innovative Service ModulesDesigned so that a qualified service technician
can quickly replace the brushes and cord.
Vario-Lock PositioningRotates and locks chisel into 12 different
positions to optimize working angle.
Dust Collection Drilling System MostCompact,LightweightDust
Collection Hammer DustCollectionUnitwith
Microfilter System
Microfilter SystemCaptures the highest volume of all size dust particles. Bosch offers a complete line of Dustless Tool Systems. See your Bosch Associate for details.
4 Boschtools.com
model number 11250VSR 11253VSR te 2 StD
Rpm 0-1,000 0-1,300 0-1,200Bpm 0-4,400 0-5,800 0-4,600
Drilling Capacity 3/4" 1" 7/8"Core Bit Capacity 1-2/3" 2-5/8" N/A
modes of operation 2 3 2tool Holder SDS-plus SDS-plus SDS-plus
length 13.3" 14.8" 14.3"Weight 5.4 lbs. 6.4 lbs. 5.95 lbs.
model number 11255VSR 11224VSR te 6 S te 7 C
Rpm 0-1,300 0-1,100 0-880 0-900Bpm 0-5,800 0-6,150 0-5,100 0-4,020
Drilling Capacity 1" 7/8" 1" 1"Core Bit Capacity 2-5/8" 2-1/2" N/A N/A
modes of operation 3 3 2 3tool Holder SDS-plus SDS-plus SDS-plus SDS-plus
length 17.3" 17.5" 12.6" 13.5"
Weight 6.7 6.5 6.2 7.0 lbs.
11255VSR 1" SDS-plus Bulldog Extreme Rotary Hammer
TE 6 S SDS-plus Rotary Hammer
TE 7 C SDS-plus Rotary Hammer
11224VSR 7/8" SDS-plus Bulldog Rotary Hammer
Excellent for:
Mounting electrical boxes and conduit.
Anchoring electrical service panels, metal door frames, drywall track.
Fastening duct straps to ceiling through metal deck into concrete; aluminum storefronts to concrete/masonry materials.
Installation of steel columns, stairs, and hand rails.
Suspending water sprinkler pipes and other fire protection items from concrete ceiling.
Light chipping and scraping using the hammer only mode. (11228VSR only).
Double insulated, UL listed, complies to OSHA.
6.1AMPS
1.6Ft-LbS
IMPACT ENERGY 650WATTS
1.3Ft-LbS
IMPACT ENERGY
720WATTS
1.9Ft-LbS
IMPACT ENERGY
650WATTS
1.33Ft-LbS
IMPACT ENERGY
7.2AMPS
2.2Ft-LbS
IMPACT ENERGY
6.9AMPS
1.6Ft-LbS
IMPACT ENERGY
7.5AMPS
2.2Ft-LbS
IMPACT ENERGY
SDS-plus Rotary HammersBosch vs. Hilti Comparison Guide
look for the Bosch advantage
11250VSR 3/4" SDS-plus Rotary Hammer
11253VSR 1" SDS-plus Bulldog Extreme Rotary Hammer
TE 2 STD SDS-plus Rotary Hammer
3/4" 1" SDS-plus Rotary Hammers
RH328VC 1-1/8" SDS-plus Rotary HammerRH328VCQ 1-1/8" SDS-plus Rotary Hammer
with Quick Change Chuck System
RH432VCQ 1-1/4" SDS-plus Rotary Hammerwith Quick Change Chuck System
TE 40 AVR C SDS-plus Rotary Hammerwith Quick Change Chuck System
Excellent for:
Mounting electrical boxes and conduit.
Anchoring electrical service panels, metal door frames, drywall track.
Fastening duct straps to ceiling through metal deck into concrete; aluminum storefronts to concrete/masonry materials.
Installation of steel columns, stairs, and hand rails.
Suspending water sprinkler pipes and other fire protection items from concrete ceiling.
Light chipping and scraping using the hammer only mode.
model number RH328VC / VCQ te 30 aVR
Rpm 0-900 750Bpm 0-4,000 4,080
Drilling Capacity 1-1/8" 1-1/8"
Core Bit Capacity 3-1/8" N/Atool Holder SDS-plus SDS-plus
Vario-lock Yes Yes
length 12.5" / 13.6" 14.9"Weight 7.7 / 7.9 lbs. 9.3 lbs.
model number RH432VCQ te 40 aVR C
Rpm 0-760 0-550Bpm 0-3,600 0-3,180
Drilling Capacity 1-1/4" 1-1/8"
Core Bit Capacity 3-1/2" N/Atool Holder SDS-plus SDS-plus
Vario-lock Yes Yes
length 15.8" 16.7"Weight 10.3 lbs. 12.3 lbs.
8.0AMPS
2.6Ft-LbS
IMPACT ENERGY
8.5AMPS
3.7Ft-LbS
IMPACT ENERGY
850WATTS
2.4Ft-LbS
IMPACT ENERGY
1010WATTS
3.6Ft-LbS
IMPACT ENERGY
5Toll Free: 877-BOSCH-99
TE 2 STD SDS-plus Rotary Hammer
1-1/8" 1-1/4" SDS-plus Rotary Hammers
SDS-plus Rotary HammersBosch vs. Hilti Comparison Guide
look for the Bosch advantage
TM
TM
TE 30 AVR SDS-plus Rotary Hammerwith Quick Change Chuck System
RH328VC Shown
11320VS Excellent for:
Removing wall and floor tile
Removing residual adhesive
Light chiseling
Light demolition
Grooving concrete for wires
Cleaning joints
Removing stucco and plaster
Any job that requires a compact, powerful chipping hammer
* with dust collection
model number 11250VSRD te 6 S pRo te 7 C pRo
Rpm 0-1,000 0-880 0-900Bpm 0-4,400 0-5,100 0-4,020
Drilling Capacity 3/4" 3/4" 1"
Core Bit Capacity 1-2/3" N/A N/Amodes of operation 2 2 3
tool Holder SDS-plus SDS-plus SDS-plus
length* 19.6"* 12.6" 13.5"Weight 7.4 lbs. N/A 8.5 lbs.
model number 11320VSR
Bpm 0-3,500tool Holder SDS-plus
length 14.8"
Weight 7.9 lbs.
11250VSRD 3/4" SDS-plus Rotary Hammer TE 6S PRo SDS-plus Rotary Hammer
TE 7C PRo SDS-plus Rotary Hammer
650WATTS
720WATTS
6.1AMPS
1.6Ft-LbS
IMPACT ENERGY
1.33Ft-LbS
IMPACT ENERGY
1.9Ft-LbS
IMPACT ENERGY
Excellent for:
Dust-free drilling in occupied rooms or dust-sensitive areas.
Mounting electrical boxes to masonry and concrete.
Anchoring metal door frames.
Anchoring drywall track.
Fastening duct straps to ceiling.
Fastening aluminum storefronts to concrete/masonry materials.
Installation of steel columns, stairs, and hand rails.
Light chipping and scraping using the hammer only mode.
SDS-plus Rotary HammersBosch vs. Hilti Comparison Guide
6 Boschtools.com
SDS-plus Dust Collection | Chipping
11320VS SDS-plus Chipping Hammer
6.5AMPS
3.2Ft-LbS
IMPACT ENERGY
look for the Bosch advantage
Popular Mechanics
model number 11264eVS te 60 te 60 atC/aVR
Rpm 170-340 0-485 0-485 / 695Bpm 1,700-2,900 0-2,785 0-2,785
Drilling Capacity 1-5/8" 1-9/16" 1-5/8"Core Bit Capacity 4-1/8" N/A N/A
tool Holder One-hand SDS-max Two-hand SDS-max Two-hand SDS-maxVario-lock 12 Positions Yes Yes
torque Control Clutch Clutch Clutch + ATC
Vibration Reduction Mech. & Handle No Yes (AVR)
length 19.25" 19.0" 19.0"
Weight 14.3 lbs. 13.9 lbs. 16.3 lbs.
11264EVS 1-5/8" SDS-max Combination Hammer
TE 60 SDS-max Combination Hammer
TE 60 ATC/AVR SDS-max Combination Hammer
Excellent for:
Mounting electrical boxes and conduit.
Anchoring electrical service panels, metal door frames, drywall track.
Fastening duct straps to ceiling through metal deck into concrete; aluminum storefronts to concrete/masonry materials.
Installation of steel columns, stairs, and hand rails.
Suspending water sprinkler pipes and other fire protection items from concrete ceiling.
Light chipping and scraping using the hammer only mode. (11228VSR only).
Double insulated, UL listed, complies to OSHA.
11240 1-9/16" SDS-max Combination Hammer
TE 50 SDS-max Combination Hammer
10AMPS
13AMPS
5.2Ft-LbS
IMPACT ENERGY
8.1Ft-LbS
IMPACT ENERGY
model number 11240 te 50
Rpm 400 0-550Bpm 3,000 0-3,180
Drilling Capacity 1-9/16" 1-9/16"
Core Bit Capacity 4" N/Atool Holder SDS-max SDS-max
Vario-lock No Yes
length 17.3" 18.2"Weight 13.2 lbs. 12.6 lbs.
1050WATTS
3.9Ft-LbS
IMPACT ENERGY
1200WATTS
5.2Ft-LbS
IMPACT ENERGY
1200WATTS
5.2Ft-LbS
IMPACT ENERGY
7Toll Free: 877-BOSCH-99
TE 6S PRo SDS-plus Rotary Hammer
TE 7C PRo SDS-plus Rotary Hammer
SDS-max Combination HammersBosch vs. Hilti Comparison Guide
SDS-max Combination Rotary Hammers
look for the Bosch advantage
TM
8 Boschtools.com
model number 11263eVS te 70 te 70 atC
Rpm 145-280 0-250/360 0-250/360Bpm 1,350-2,800 0-2,760 0-2,760
Drilling Capacity 1-3/4" 1-3/4" 1-3/4"Core Bit Capacity 6" 6" 6"
tool Holder SDS-max SDS-max SDS-max
Vario-lock 12 positions Yes Yestorque Control Clutch Clutch Clutch + ATC
length 21.0" 20.6" 20.6"Weight 17.9 lbs. 16.9 lbs. 19.6 lbs.
model number 11245eVS te 80 atC/aVR
Rpm 120-250 250/380
Bpm 1,100-2,500 1,920-2,760Drilling Capacity 2" 2"
Core Bit Capacity 6" 6"
tool Holder SDS-max SDS-max
Vario-lock 12 positions 12 positionstorque Control Clutch Clutch + ATC
Vibration Reduction No Yes
length 23.5" 21.8"Weight 24.5 lbs. 22.5 lbs.
11263EVS 1-3/4" SDS-max Combination Hammer
TE 70 ATC SDS-max Combination Hammer
13.5AMPS
11.1Ft-LbS
IMPACT ENERGY
14AMPS
13.3Ft-LbS
IMPACT ENERGY
1600WATTS
8.15Ft-LbS
IMPACT ENERGY
Excellent for:
Dust-free drilling in occupied rooms or dust-sensitive areas.
Mounting electrical boxes to masonry and concrete.
Anchoring metal door frames.
Anchoring drywall track.
Fastening duct straps to ceiling.
Fastening aluminum storefronts to concrete/masonry materials.
Installation of steel columns, stairs, and hand rails.
Light chipping and scraping using the hammer only mode.
Combination HammersBosch vs. Hilti Comparison Guide
1-3/4" 2" SDS-max Combination Rotary Hammers
11245EVS 2" SDS-max Combination Hammer
look for the Bosch advantage
TE 80 ATC/AVR SDS-max Combination Hammer
1700WATTS
8.5Ft-LbS
IMPACT ENERGY
model number 11247
Rpm 400
Bpm 3,000Drilling Capacity 1-9/16"
Core Bit Capacity 4"
tool Holder Spline
Vario-lock NoConstant electronic No
length 17.3"Weight 13.6 lbs.
Excellent for:
and concrete.
Anchoring metal door frames.
Anchoring drywall track.
Fastening duct straps to ceiling.
Fastening aluminum storefronts to concrete/masonry materials.
Installation of steel columns, stairs, and hand rails.
Medium chipping and scraping using the hammer only mode.
model number 11265eVS
Rpm 170-340Bpm 1,700-2,900
Drilling Capacity 1-5/8"
Core Bit Capacity 4-1/8"tool Holder Spline
Vario-lock No
Vibration Reduction Mech. & Handle
length 19.25"Weight 14.7 lbs.
9Toll Free: 877-BOSCH-99
TE 80 ATC/AVR SDS-max Combination Hammer
10AMPS
5.2Ft-LbS
IMPACT ENERGY
13AMPS
8.1Ft-LbS
IMPACT ENERGY
Combination HammersBosch vs. Hilti Comparison Guide
Spline Combination Rotary Hammers
11247 1-3/4" Spline Combination Hammer
11265EVS 1-5/8" Spline Combination Hammer
No Hilti Comparison
No Hilti Comparison
look for the Bosch advantage
TM
10 Boschtools.com
model number 11321eVS 706 / te 706 aVR
Bpm 1,300-2,900 2,760Vario-lock 12 position Yes
tool Holder SDS-max SDS-max
Vibration Reduction Handle/Mech Yes (TE 706 AVR)
length 18.6" 22"Weight 12.8 lbs. 17.4 lbs.
model number 11388 11387 te 500
Bpm 2,800 2,800 3,180
Vario-lock 12 position N/A 12 position
tool Holder SDS-max 3/4" Round Hex SDS-max
length 17.5" 17.5" 18.5"Weight 11.6 lbs. 12 lbs. 12.4 lbs.
theft protection No No Available
Demolition HammersBosch vs. Hilti Comparison Guide
10-12 Lb. Demolition
TE 500 SDS-max Demolition Hammer
1100WATTS
5.5Ft-LbS
IMPACT ENERGY
Excellent for:
breaking and chiseling concrete.
Cleaning out old deteriorating cement between bricks.
Deep removal of concrete between joints.
Cutting or breaking asphalt.
Digging out clay or hard packed gravel.
breaking out frozen ground.
Driving grounding rods or installing parking bumpers.
bushing concrete surface to break down high spots or roughing up smooth surface for bonding or architectural designs.
11388 SDS-max Demolition Hammer
10AMPS
5.9Ft-LbS
IMPACT ENERGY
11321EVS SDS-max Demolition Hammer
13AMPS
9.6Ft-LbS
IMPACT ENERGY
10AMPS
5.9Ft-LbS
IMPACT ENERGY
11387 3/4" Round Hex Demolition Hammer
look for the Bosch advantage
TE 706 / TE 706 AVR SDS-max Demolition Hammer
1200WATTS
7.4Ft-LbS
IMPACT ENERGY
model number 11316eVS 11317eVS te 805 te 1000aVR
Bpm 900-1,890 850-1,800 2,000 1,950
Variable Speed 7 settings N/A No NoVario-lock 12 position N/A Yes No
tool Holder SDS-max 3/4" Hex Hilti 7/8" Hex Hilti 7/8" Hex
Vibration Reduction No No No Yes (AVR)
length 22.5" 22" 23.6" 22.6" Weight 22.5 lbs. 22 lbs. 22.6 lbs. 26 lbs.
11Toll Free: 877-BOSCH-99
TE 706 / TE 706 AVR SDS-max Demolition Hammer
Demolition HammersBosch vs. Hilti Comparison Guide
11316EVS SDS-max Demolition Hammer
11317EVS 3/4" Round Hex Demolition Hammer
20 Lb. Demolition
14AMPS
18.4Ft-LbS
IMPACT ENERGY
12.8AMPS
16.5Ft-LbS
IMPACT ENERGY
TE 1000 AVR Hilti Hex Demolition Hammer
1600WATTS
16.3Ft-LbS
IMPACT ENERGY
look for the Bosch advantage
Excellent for:
breaking and chiseling concrete.
Cleaning out old deteriorating cement between bricks.
Deep removal of concrete between joints.
Cutting or breaking asphalt.
Digging out clay or hard packed gravel.
breaking out frozen ground.
Driving grounding rods or installing parking bumpers.
bushing concrete surface to break down high spots or roughing up smooth surface for bonding or architectural designs.
TE 805 Hilti Hex Demolition Hammer
1350WATTS
12.5Ft-LbS
IMPACT ENERGY
12 Boschtools.com
Breaker HammersBosch vs. Hilti Comparison Guide
model number BH2760VC te 3000 aVR
Bpm 1,000 840accepts air Steel Yes Yes
tool Holder 1-1/8" Hex 1-1/8" Hex
Vibration Control
Main Handle + Mechanism
Yes
Vibration levels 8.0 m/s 8.5length 30.5" 32.5"Weight 65 lbs. 66 lbs.
model number 11335k te 1500 aVR
Bpm 1,300 1,620
accepts air Steel Yes Notool Holder 1-1/8" Hex 7/8" Hilti Hex
Vibration Control Main Handle + Mechanism
AVR
Vibration levels 10.8 m/s 12.0length 30.4" 29.9"
Weight 38 lbs. 31.3 lbs.
Steel included 1 pc 2 pcs
Hauler Case
TE 1500 AVR Breaker Hammer
TE 3000 AVR Breaker Hammerwith Basic Cart plus 4 Chisels
Excellent for:
breaking and chiseling concrete.
Cleaning out old deteriorating cement between bricks.
Deep removal of concrete between joints.
Cutting or breaking asphalt.
Digging out clay or hard packed gravel.
breaking out frozen ground.
Driving grounding rods or installing parking bumpers.
bushing concrete surface to break down high spots or roughing up smooth surface for bonding or architectural designs.
15AMPS
34Ft-LbS
IMPACT ENERGY
15AMPS
49.5Ft-LbS
IMPACT ENERGY
BH2760VC NEW! Brute Breaker HammerBH2760VCB with Basic Cart plus 2 ChiselsBH2760VCD with Deluxe Cart plus 4 Chisels
11335K Jack 35 Lb. Breaker Hammer
1800WATTS
22.2Ft-LbS
IMPACT ENERGY
1800WATTS
50Ft-LbS
IMPACT ENERGY
look for the Bosch advantage
TM
TM
35-60 Lb. Breaker
TE 1500 AVR Breaker Hammer
TE 3000 AVR Breaker Hammerwith Basic Cart plus 4 Chisels
13Toll Free: 877-BOSCH-99
60 Lb. Breaker Hammer
Breaker HammersBosch vs. Hilti Comparison Guide
*See chart on page 12
BH2760VC neW! Brute Breaker Hammer*
t1757 Deluxe Hammer Hauler42.25"x18.5"x16"28.9lbs.8"FoamTires4HammerSteelSecuredStorageTruckRamp1-1/2"NylonHoldDownStrap
w/Quick Release StrapToolFreeconversiontoHandTruckLiesParalleltoFloorCordWrapMaxCapacity=250lbs.
t1657 Basic Hammer Hauler42.5"x18."x15"21lbs.8"SemiPneumaticTires4HammerSteel
Non-secured StorageBungeeHoldDownStrapMaxCapacity=250lbs.
Bosch Hammer Haulers
non-Slip Housing CoverRubberized housing cover helps prevent tool from accidental fall over when tool is not in use
ergonomic HandlesProvide additional user comfort in all day applications
Robust ConstructionTool housing and all parts of the impact mechanism including piston and rod are made of durable and lightweight cast aluminum
Dustproof Switch Can be operated without taking hands off the handles
Service minder Brush SystemShuts the Brute off when brush replacement, lubrication or preventive maintenance is needed
unmatched power to Weight Ratio
HiTSHaRDeR
active Vibration ControlVibration Reduction in the hammer mechanism and the grip area provides maximum user comfort for extended periods of work
TM
ViBRateSup to 50%
LESS
ToNSpeR HouR3.2RemoVeSup to
14 Boschtools.com
Hammer Carbide BitsBosch vs. Hilti Comparison Guide
Rebar CutterCuts rebar, cost and timeSolve the #1 problem in concrete drilling
High quality carbide Forlongdrilling life
Step 1: Drill with SDS-plus carbide bit and remove after contact with rebar
1Cutting Rebar
Step 2: Replace bit with rebar cutter and switch to rotary mode
2 Step 3: Cut through rebar and remove after contact with concrete
3 Step 4:Switch back to hammer carbide bit to continue drilling
4
*Based on independent head-to-head testing of 1/4" bits performed by Rbel
Diffusion BondingCarbide and steel are bonded together at a molecular level. Reuleaux
Triangle
Hole shapes based on tip type
2-cutter 4-cutter X5L Centric Conical
The X5L tip shape provides rounder holes for precision anchoring applications
SDS-plus Shank Eliminates need for a separate drill
Relief HoleDissipates heat andallows for slug removal
Steep Spiral FluteRemoves debris fast
4X Life vs. HiltiBased on independent head-to-head testing of 1/4" bits - Hilti TE-C3XSolid Carbide DesignDiffusion BondingCentric TipWear MarkerBest Life in ConcreteBest Life in Rebar
Bosch Hilti
Solid Carbide tip Yes NoDiffusion Bonded Yes Noindependent test
up to 4x life* Yes No
Full Head Carbide tip Faster drilling speed and less carbide wear
Centric active tip Guides bit and cuts through concrete and rebar Provides rounder holes
Wear mark Alerts user when bit has worn to a level inappropriate for precision anchoring
Flute Design Fast dust removal Runs cooler Optimized flute cross section reduces stress
Bosch Hilti
Rebar Cutter* yes no
*Innovation not available from Hilti
15Toll Free: 877-BOSCH-99
SDS-plus Shank
Bosch Hilti
Solid Carbide tip Yes NoDiffusion Bonded Yes Noindependent test
up to 4x life* Yes No
Bosch Hilti
Rebar Cutter* yes no
Hammer Carbide BitsBosch vs. Hilti Comparison Guide
Speed-X
Multi-Construction Bit
Centric tip Guides bit and cuts through hard
and reinforced concrete
angled Dust Channels Reduced heat build-up resulting in longer life
Wear mark Identifies when bit has worn to level inappropriate for precision anchoring
inclined Side Cutters Aggressive edge for faster cutting
long pitch Spiral Increased speed and reduced vibration
Robust Head Longservicelife,evenin impact applications
Steep Flute with Ribs
Optimal dust removal in any material
Sharp, ground Cutting edges
Fastdrillinginhard materials
Softened ShankAggressive gripping power
Drills practically everything
Optimal X PatternInclined Side CuttersS Shaped CarbideActive Centering TipDeep FlutesShort HeadWear Marker
Bosch Hilti
optimized x Yes Noinclined Side
Cutters Yes No
activeCenter tip
Yes No
Bosch Hilti
multi-Construction Bit* yes no
*Innovation not available from Hilti
16 Boschtools.com
Hammer Carbide BitsBosch vs. Hilti Comparison Guide
How Does R-Tec Work? Our new R-Tec reflection element reflects the hammers energy back into the work material, increasing the rate of removal by 15%. And the R-Tec chisel features a unique cutting head with extra wedges for increased breakout. Bosch SDS-max R-Tec chisels and points produce faster results in less time and help increase overall jobsite productivity and profitability.
innovative Reflection element
Increases material removal rate by up to 30%
SDS-max Shank
High-quality Hardened SteelCan be re-sharpened, re-forged and
provides long service life
Star point tipSelf sharpening, less binding
The reflection element reflects the energy of the return shock and converts it into new impact energy.
Conventional Chisel
R-Tec Chisel
SDS-max R-Tec
Steep Flute with RibsRetains sharp geometry and eliminates jamming while chipping
Also Available R-tec Sharp with Power Ribs
R-Tec Up to 30% Faster Material RemovalSaves time and moneySelfsharpening
Bosch Hilti
R-tec w/Reflection* yes no
*Innovation not available from Hilti
17Toll Free: 877-BOSCH-99
Bosch Hilti
R-tec w/Reflection* yes no
Measuring & Layout ToolsBosch vs. Hilti Comparison Guide
model number glR225 pD4
accuracy 1/16" ( 1.5mm) 1/12" ( 2.0mm)
max Range up to 230' (70m) up to 230' (70m)
min & max Function Yes Noarea Yes No
Volume Yes Noindirect measurement Yes No
multi-Wall Yes NoReference points Front,Tripod,Back,
Corner PinBack
model number glR500 pD40
accuracy 1/25" (1.0mm) 1/25" (1.0mm)
max Range up to 500' (151m) up to 650' (200m)
min & max Function Yes NoVolume Yes No
indirect measurements Yes Nomulti-Surface area Yes No
trapezoid Yes NoStake out Yes No
Laser Distance Measurers
GLR225 / GLR500 Excellent for:Precise distance and area calculations for almost all applications
Advanced measurements and calculations such as indirect length, multi-surface area, and more
Measuring hard to access areas and locations
Laser Range Meter
Laser Range Meter
Laser Distance Measurer
Laser Distance Measurer
look for the Bosch advantage
18 Boschtools.com
model number gpl2 pmp 32
accuracy 1/8"@50' 1/8"@30'Range 30' 30'
Compensation or Self-leveling type
Self-Leveling Self-Leveling
Compensation or Self-leveling range
5 4number of Beams 2 2
plumb up Yes Yes
plumb Down Yes Yes
Warranty 3 Year 2 Year
model number gpl5C pmC 36
accuracy 1/8"@50' 1/8"@30'Range 100' 100'
number of point Beams
5 5
Cross points 2(Up/Down) 1(Level)Compensation or
Self-leveling typeSelf-Leveling Self-Leveling
Compensation or Self-leveling range
4 3.5
Warranty 3 Year 2 Year
Measuring & Layout ToolsBosch vs. Hilti Comparison Guide
Point Lasers
Plumb Laser
5-Point Alignment Self-Leveling Laser
Combilaser
2-Point Self-Leveling Laser
GPL5C Excellent for:5 point laser plus highly visible laser cross lines
Point or layout transfer from floor to ceiling
Simple wall and vertical stud layout
Alignment of frames and sills
GPL2 Excellent for:Quickly aligning and transferring points from floor to ceiling
Walls, tracks and partitions
Ceiling fixtures and lighting
Pipe installation
look for the Bosch advantage
19Toll Free: 877-BOSCH-99
model number D-tect 150 pS-200
Wet Concrete mode
Yes Nometal Scan
Depth (Steel)up to 6"/150mm up to 7.1"/180mm
metal Scan Depth (Copper)
up to 6"/150mm No
live Wire Scan Depth
up to 3-1/8"/80mm NoWood
Scan Depth up to 1-1/2"/38mm No
plastic pipe Scan Depth
up to 2-3/8"/60mm Nopower (4) AA 9.6V NiMH rechargeable
Wall Scanner Ferroscan system
model number gll2-80 pmC 46 pml 32-R
accuracy 1/8"@50' 1/16" @30' 1/16" @30'Range 65' 100' 30'
Range with Detector 265' N/A 100'360 Horizontal plane Yes No No
360 Vertical plane Yes No NoCross points 2 1 1
Compensation or Self-leveling type
Self-Leveling Self-Leveling Self-Leveling
Warranty 3 Year 2 Year 2 Year
GLL2-80 Excellent for:Level and align/plumb applications
Vertical alignment of wall track and partitions
Mounting fixtures and fittings using level and layout lines
tile layout for wall and floor covering
Hanging cupboards, shelves and furniture on the wall
Aligning drainage pipes, mounting heaters, and fire sprinkler layout
5-Point Alignment Self-Leveling Laser
Line Laser Line Laser
Measuring & Layout ToolsBosch vs. Hilti Comparison Guide
Point Lasers Detection
look for the Bosch advantage
Wall Scanner D-tect 150 Excellent for:Wall/floor scanning on cured concrete, wet concrete, masonry and drywall surfaces
Locating ferrous metal i.e. rebar, non-ferrous metal i.e. copper pipe, live wires, plastic pipes, and wood studs in floors, walls, and ceilings
Structural analysis and remodeling applications
Superb depth, accuracy and material type detection
Increasing productivity by minimizing uncertainties
20 Boschtools.com
model number Bp350 pua 10
Height min 4' 7" 4' 5"
Height max 11' 6" 9' 5"mounting thread 1/4 - 20 N/A
Clamp Yes Notool mount Yes No
Telescoping Pole System Telescoping Brace
model number DaF220k
2(Front&Back)
angle accuracy 0.1
Compound Cut angle Range
0 to 180
Simple miter Cut input Range
0 to 220
leg extension Range
0" to 6-3/4"
Measuring & Layout ToolsBosch vs. Hilti Comparison Guide
DAF220K Excellent for:Calculating the exact miter and bevel angles needed for a perfect fit
Measuring for crown moldings and other type of moldings, including baseboard, base shoe, and chair rails
Measuring angles of existing objects
Measuring angles in confined situations
Digital Angle Finder
easy Calculation of Cut angles
Angle Measuring Attachments
measure 1st angle
1
2
measure 2nd angle
3
Display the exact miter and Bevel angles at the touch of a Button for a perfect Fit
look for the Bosch advantage
21Toll Free: 877-BOSCH-99
Measuring & Layout ToolsBosch vs. Hilti Comparison Guide
Attachments
look for the Bosch advantage
model number Wm1 pma 78
Height adjustment Range
2-1/2" N/A
Swiveling 1/4-20threaded mount
Yes NoRetractable Feet for
Freestanding use Yes No
tripod/pole mount Yes Unknown
magnets Yes No Wall mounting Yes Yes
model number Wm4 pRa 71
5/8-11 threads Yes Yes
Height adjustmentScale
Yes Yes
Ceiling perimeter mount
Yes Yes
locks scale into place
Yes Yes
Positioning Device
Universal Adapter
Wall MountWall Mount
model number Bt300HD pa 911 pua 30
Height min 4' 3' 3" 2' 8"
Height max 9' 8" 5' 5" 9' 2"mounting thread 5/8" 5/8" 5/8"
mechanism to set height
Quick Clamp Quick Clamp Quick Clamp
Weight 7.2kg N/A N/A
Heavy-Duty Aluminum
Elevator Tripod
Height Adjustable
Tripod
Crank Tripod
Robert Bosch tool Corporation1800 W. Central Rd.mount prospect, il 60056telephone 224-232-2000Fax 224-232-3169boschtools.com
2010-221 v2