CANM8 General Product Installation 025 - Carsec - … Cherokee 2010 Jeep Cherokee Jeep Renegade Jeep...

transcript

CANM8 Product InstallationManufacturers

SELECT YOUR VEHICLE MANUFACTURER

Accura Lancia YamahaAlfa Land RoverAston Martin LexusAudi LincolnBentley MANBMW MazdaBuick MazeratiChevrolet MercedesChrysler MGCitroen MitsubishiDacia NissanDAF PeugeotDodge PorscheFerrari RenaultFiat RoverFord SaabGM Single Wire CAN ScaniaGMC SeatHGV SkodaHonda SmartHummer SsangyongHyundai SubaruInfinity SuzukiIsuzu TeslaIveco ToyotaJaguar Vauxhall / OpelKia VWLamborghini Volvo

Additional Product Information

CANM8 General Installation File

Product InformationThe installation information in this file is general to all CANM8 interfaces that producesignal or power control outputs:

GENERAL CAN INTERFACES PARKING SENSOR CONTROL INTERFACES

CANM8-NAV CANM8-PARKCANM8-PULSE CANM8-MERCPARKCANM8-POWER CANM8-PARK*SM2CANM8-DUO CANM8-PARK*SM3CANM8-TWINPULSE CANM8-PARK*ONECANM8-RPM CANM8-PARK*ONE (R)CANM8-POWER*RPM

CANM8-CRUISELINK

CANM8-AV3

Please note that the wire functions detailed vary with some products:

CANM8-POWER*RPM

PURPLE > Ignition On Output : 12v when RPM is higher than 500 RPM

CANM8-CRUISELINK

PURPLE > Ignition On Output : 12v when ignition is switched on.GREEN > Hi-Res Speed Signal Output : 12v pulsing 10Hz = 1MPH (approx).YELLOW > Lo-Res RPM Output : 12v pulsing 1Hz = 25RPM (approx).

CANM8-MERCPARKGREEN > Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).PURPLE > Speed Dependent Output : 12v continuously while below 6 MPH

> Also 20s timed output when gearing from Park to DriveORANGE > Speed Dependent Output : 12v contiuously up to 6 MPHPINK > FPS Disable : 0v Output - Disabled when Reverse is selected.BROWN > Reverse Engaged Output : 12v when reverse gear is selected.YELLOW > NOT USED

CANM8-PARK*SM2GREEN > Control Output : 12v while below 6 MPH (150mA Max)PURPLE > Ignition On Output : 12v when ignition is switched on (1A Max)

CANM8-PARK*SM3GREEN > Control Output : 12v while below 6 MPH (3A Max)PURPLE > Ignition On Output : 12v when ignition is switched on (3A Max)BROWN > Reverse Output : 12v when ignition is switched on (3A Max)

Alfa Model List

147159

BreraGTGuiliettaMito

Aston Martin Model List

DB9Vantage

Audi Model List

A1A3 2003 >A3 2012A4 > 2007A4 2008 >A5 & S5A6 2004 >A6 2011 >A7A8 2003 >A8 2011 >Q3Q5Q7 2006 >Q7 2015 >R8TT > 2006TT 2007 >

Bentley Model List

Bentayga 2016 >

BMW Model List

1 Series 2004 >1 Series 2011 >3 Series > 20043 Series 2005 >3 Series 2011 >5 Series (E60)5 Series (F10)6 Series (E63-E64)7 Series (E65-E66)7 Series (F01-F02)GSR-1200 2013>X1X3 > 2010X3 2011 >X5 2008 >X5 2014 >X6 2008 >Z4 2003 >Z4 2009 >Mini 2001 >Mini 2007 >MINI 2014 >Mini Countryman

Chevrolet Model List

AveoCamaroCaptivaColoradoCruzeEscaladeHHRMalibuOrlandoSilveradoSonicSparkVolt

Chrysler Model List

C300300 C 2012Country 2008 >Grand Cherokee 2005Grand Cherokee 2010Jeep CherokeeJeep RenegadeJeep WranglerTown 2008 >Voyager 2008 >

Citroen Model List

Berlingo 2003 >Berlingo 2008 >C-CrosserC2C3C4C5 2005 >C8DispatchDS3DS4DS5Jumper 2006>Jumper 2014 >Jumpy 2008NemoPicasso

Dacia Model List

DusterLodgy

Dodge Model List

CaliberCaravanCaravan 2008 >Challenger < 2011Challenger 2012Charger 2015 >DartDurangoRam < 2013Ram 2013 >

Fiat Model List

BravoCromaDoblo > 2011Doblo 2012 >Ducato 2006 >Ducato 2014 >FiorinoFreemontGrande PuntoPandaScudoStiloViaggio

500 X500 L

Ford Model List

B-Max 2012 >Ecosport 2013 >EscapeExpedition 2007 >F150 F250F-350 2006 >F-350 2011 >Fiesta >2007Fiesta 2008 >Fiesta 2013 >Focus & C-MAX 2005Focus & C-MAX 2011FusionFusion (USA)GalaxyGalaxy 2015>KAKugaKuga 2013Mondeo > 2006Mondeo 2007 >Mondeo 2015 >MustangRanger 2012 - 2016Ranger 2016 >S - MaxTransit 2006 >Transit 2014 >Transit ConnectTransit Custom

GMC Model List

CanyonYukon Denali

Honda Model List

AccordAccord 2008 >Honda CivicCrossroadCR-V 2007 >CR-V 2012CR-ZElementFreedFR-VInsightJazzOdysseyStepwagonStream 2006 >

Hyundai Model List

i10i20i30i40ix35VelosterH1- i800

Infinity Model List

FX35FX45

Iveco Model List

Daily 2006 >Daily 2014 >

Jaguar Model List

F-Type 2013 >S-TypeX-TypeXE 2015 >XF 2008>XJ6-XJ8XKR >2007XKR 2008>

Kia Model List

CarensCeedPicantoSorentoSoulSportageVenga

Lancia Model List

DeltaMusaThemaThesisYpsilon

Land Rover Model List

DefenderDiscovery 3Discovery 4FreelanderFreelander 2Range RoverRange Rover 2013EvoqueRR Sport < 2014RR Sport 2014 >

Lexus Model List

is250RX350RX400H

Mazda Model List

2356 2005 >6 2012 >CX-5CX-7CX-9DemioMPVMX-5RX-8

Mercedes Model List

A Class (168) > 2004A Class (169) 2005 >A Class (176) 2012 >ActrosAtegoAxorB Class (245) 2005 >B Class (246) 2011 >C Class (203) 2000 >C Class (204) 2007 >C Class (205) 2014 >CLK Class (209) 2002 >CLS Class (219) 2004 >CLS Class (218) 2011 >E Class (210) 2000 >E Class (211) 2002 >E Class (212) 2009 >G Class (463) 1990 >GLA Class (156) 2014 >GLK Class 2008 >M Class (163) 2000 >M Class (164) 2006 >M Class (166) 2011 >R Class (156) 2005 >S Class (221) 2005 >S Class (222) 2014 >SL Class (230) 2003 >SL Class (231) 2012 >SLK Class (R171) 2004 >Sprinter (903) 2000 >Sprinter (906) 2006 >Sprinter 2015 >V Class (447) 2014>Viano / Vito (639) 2004 >Vito 2015 >

Mitsubishi Model Sheet

ASXColtGrandisEvo 10L200 2006>L200 2012 >Outlander 2007>Outlander 2013Space Star 2013

Nissan Model List

350Z370ZAlmeraAltimaCubeElgrandJukeLeafMicraMuranoNavarraNoteNV 200NV 400PathfinderPixoPrimastarPrimeraQashqaiRogueSentraSkyline (350GT)X-TrailX-Trail 2007 - 2014X-Trail 2014 -

Peugeot Model List

207208200830730840740075085008

206 2002>

607 2000 >607 2005 >807 >2005807 2006>BipperBoxer 2006 >Boxer 2014 >ExpertPartner > 2007Partner 2008 >RCZ

Porsche Model List

Boxster > 2004Boxster 2004 >CayenneCayman911 (996) 2001911 (997) 2005>

Renault Model List

ClioClio 2012 >EspaceFluenceKangoo 2008 >Kangoo 2003 >KoleosLaguna 2Laguna 3Master > 2008Master 2009 >Megane 2Megane 3ModusScenicScenic 2009TrafficVel SatisWindZoe

Rover Model List

7575 (V8)

Saab Model List

9395 2006 >95 2010 >

Seat Model List

AlhambraAltea > 2007Altea 2008 >ExeoIbizaIbiza 5 2008 >Ibiza 6 2012 >Ibiza 7 2015 >Leon 2005 >Leon 2014 >

Skoda Model List

FabiaOctaviaOctavia IIOctavia IIIRapidRoomsterSuperbYeti

Smart Product List

CarFourtwo

Ssangyong Model List

ActyonKorandoKyronRodius 2005 - 2014Rodius 2014 >Turismo 2014 >

Subaru Model List

ForesterImprezaLegacyOutbackXV

Suzuki Model List

AltoGrand VitaraSplashSwiftSX4

Tesla Model List

Tesla S

Toyota Model List

Avensis 2009 >BBCamry 2006 >EstimaGT86Hi-LuxiQLand CruiserPrius 2005 >Prius 2009 >ProAce 2013 >RAV 4Verso SYaris 2006 >Yaris 2011 >

Vauxhall / Opel Model List

AgilaAmperaAntaraAstra H 2005 - 2010Astra J 2009 - 2015Astra K 2016 >CascadaCombo >2012Combo 2012 >Corsa >2006Corsa 2006 >InsigniaMerivaMeriva 2010 >Mocca 2012 >Movano > 2008Movano 2009 >SignumVectraVivaroZafira AZafira BZafira C

VW Model List

AmorakBeetleCaddy 2004 - 2015Caddy 2016 >CrafterEosFoxGolf VGolf VIGolf VIIGolf PlusJettaPassat 02-05Passat 05 >Passat 11 >PoloPolo 2009 - 2014Polo 2014 >RoutanSciroccoSharanSharan 2010 >TiguanTouareg 2003 >Touareg 2011 >TouranTransporter 2003Transporter 2010

Volvo Model List

C30HGVS40S60S80V40V50V60 & XC60V70 & XC70XC90

Yamaha Model List

FJR1300

CANM8-CANNECT Installation File

Alfa Romeo : GT

Vehicle CAN Bus Location

The CAN wiring is located at the OBD socket, drivers dash fuse box behind dash panel.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN wiring is also available at the radio. The wire location details are on the Pin-Out diagramon the top of the radio.

CANM8 CANNECT NAV Wiring Instructions

CAN-M8 NAV Wire Wire Connection Point Or Output Function

RED > Connect via a 5 Amp fuse to a permanent 12V supply.BLACK > Connect to a good chassis ground point.WHITE >BLUE >GREEN > Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).PURPLE > Ignition On Output : 12v when ignition is switched on.ORANGE > Lights On Output : 12v when side / head lights are on.PINK > Parking Brake On Output : 0v (Ground) with parking brake on.BROWN > Reverse Engaged Output : 12v when reverse gear is selected.YELLOW > RPM Output : 12v pulsing 1Hz = 1RPM (approx).

CANM8 CANNECT PARK Wiring Instructions

CAN-M8 PARK Wire Wire Connection Point Or Output Function

RED >BLACK > Connect to a good chassis ground point.WHITE >BLUE >GREEN > Speed Signal Output : 12v pulsing 1Hz = 1MPH (approx).PURPLE > Speed Dependent Output : 12v continuously while below 6 MPHORANGE > Speed Dependent Output : 12v between speeds of 1 to 6 MPHPINK > FPS Disable : 0v Output - Disabled when Reverse is selected.BROWN > Reverse Engaged Output : 12v when reverse gear is selected.YELLOW > NOT USED

The Orange & Purple outputs will switch off when the vehicle Park Brake is applied on compatible vehicles.

Testing The Installation

Connect the interface to the plug-in wiring harness and turn the vehicles ignition 'on'.

The CANNECT interface switches on automatically when CAN activity is detected.The interface has an LED status indicator next to the connection plug, which will illuminate

GREEN when valid CAN data has been identified by the interface. When the vheicle is moved, theGREEN LED will flash to indicate that CAN Bus speed information is being processed.

If the LED indicator is illuminated RED for more than 10 seconds, the interface is functioning but cannot identify the vehicle. It is very important that the interface is only connected to the vehicle

CAN Bus wiring at the connection point location detailed at the top of the page.

If the LED fails to illuminate or flash, there is a power connection problem - recheck the connectionsIf the LED flashes RED continuously, the interface is powered but is not reading CAN data. Checkthe interface CAN HI and CAN LO connections are the correct way around. Also check that these

wires are connected to the CAN Bus wires as detailed above.

The CANNECT interface automatically switches off when the vehicle CAN Bus is inactive.This can be tested by removing the keys from the ignition, closing all vehicle doors and

switching all auxilliary equipment 'off'. The interface LED should extinguish within 60 seconds.

CAN HI = PIN 6 (Or CAN 'B' at the radio)CAN LO = PIN 14 (Or CAN 'A' at the radio)

CAN HI Connection : Vehicle CAN HI wireCAN LO Connection : Vehicle CAN LO wire

Please note: Some outputs may be un-available depending on the specification of the subject vehicle.

Connect via a 5 Amp fuse to a SWITCHED 12V supply.

CANM8 CANNECT Installation File

Alfa Romeo : Giulietta

Alfa Romeo : Mito

Alfa Romeo : 147

The CAN wiring is located at the control unit, in the passenger side footwell under the floor panel.The CAN bus wiring is a twisted pair of wires, coloured as below:

As an alternative, connect to the black connector with the purple clip at the body computer/fuse box as below:

CAN HI = GREENCAN LO = BROWN

CAN HI: POSITION 10 (BLACK/PINK)CAN LO: POSITION 28 (WHITE/PINK)

Alfa Romeo : 159

CAN wiring is also available at the radio. The wire location details are on the Pin-Out diagramon the top of the radio. The CAN HI wire may be marked as 'CAN B' and the LO wire as 'CAN A'

CAN HI = PIN 6 (PINK / BLACK)CAN LO = PIN 14 (PINK / WHITE)

Aston Martin : DB9

The CAN wiring is located at the OBD socket, under the passenger side dash.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = OBD Socket - Pin 3CAN LO = OBD Socket - Pin 11

Aston Martin : Vantage

Vehicle CAN Bus LocationThe CAN wiring is located at the Body Diagnostic socket, drivers side, bottom of the dash panel.

There are 2 diagnostic sockets marked 'Body' & 'OBD'. The OBD CAN wiring is inactive.Two CAN Buses are available at the Body socket. Connect to the GREEN Bus.

CANM8 CANNECT Wiring Instructions

GREEN Bus : CAN HI = GREEN / BROWN CAN LO = GREEN / BLACKRED Bus : CAN HI = RED / BROWN CAN LO = RED / BLACK

Audi A1 : 2010 >

The CAN wiring is located in the steering column loom.

The CAN wires are a twisted pair coloured as below:

CAN HI = ORANGE / GREENCAN LO = ORANGE / BROWN

Audi A3 : 2003 >

Remove the lower steering column cover to expose the loom to the wiper / indicator controls.The CAN bus wiring is a twisted pair of wires, coloured as below:

Some vehicles may also have CAN wiring present at the audio connector.

CANM8C CANNECT NAV Wiring Instructions

Audi A3 : 2012 >

Audi A4 > 2007

Remove the audio unit.

The interface is installed to the CAN wiring at the audio connector:

CAN HI = ORANGE / PURPLE CAN LO = ORANGE / BROWN

Audi A4 2008 >

The CAN Bus wiring can be located in the steering column loom.

The CAN Bus wiring is a twisted pair coloured as below:

Audi A5 & S5

The CAN Bus wiring can be located in the steering column loom and in the wiring harness at the

rear of the glove box. There are two CAN Bus systems that can be connected to:

CAN HI = ORANGE / PURPLE OR ORANGE / GREENCAN LO = ORANGE / BROWN

Audi A6 : 2004 >

Connect under the drivers dash.

The interface is installed in the looms in the steering column

CAN HI = ORANGE / GREEN (UNDER DASH)CAN LO = ORANGE / BROWN

Audi A6 : 2011 >

Remove the lower steering column cover.

The interface is installed to the CAN wiring at the steering column loom.

CAN HI = ORANGE / BLUECAN LO = ORANGE / BROWN

Audi A7 : 2011 >

Remove the lower drivers side dash trim.

The interface is installed to the CAN wiring in the steering column loom.

Audi A8 : 2003 >

Software versions before 25.1 will not work on the audio CAN wiring if the factory audio unit is removed.

Connect to the Orange / Green CAN Bus - usually available under the O/S dash or at the speedo connectors.

Audi A8 : 2011

The interface is installed to the CAN wiring at the BCM module, near to the centre of the car:

Audi Q3 2011 >

The CAN Bus wiring can be located in the steering column loom and in the wiring entering the front doors.

. The CAN wiring is a twisted pair of wires as below:

Connection can also be made to the ORANGE / BLACK (HI) & ORANGE / BROWN (LO) wires.These are located in the main wiring at the front & back of the vehicle

Audi Q5 2008 >

rear of the glove box. The CAN wiring is a twisted pair of wires as below:

Audi Q7 2006 >

rear of the glove box. There are two CAN Bus systems that can be connected to:

Audi Q7 2015 >

The CAN Bus wiring can be located in the steering column loom and in the wiring harness at thefront door. The CAN Bus wiring is as follows:

CAN HI = GREENCAN LO = ORANGE / BROWN

Audi R8

Audi TT 2002 > 2006

Vehicle CAN Bus LocationRemove the audio unit.

Early vehicles may not have CAN at the audio. Connect to Orange / Black & Orange / Brown at the speedo.

Audi TT 2007 >

Bentley Bentayga 2016>

The CAN wiring is located at the steering column harness

CAN HI = ORANGE / GREEN CAN LO = ORANGE / BROWN

BMW 1 Series 2004 > 2011

Vehicle CAN Bus LocationRemove the vehicle speedometer assembly. The CAN wires are located at the connection plug.

The CAN wiring can also be located at the audio unit Quadlock.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = ORANGE / GREENCAN LO = GREEN

BMW 1 Series (F20) 2011 >

Vehicle CAN Bus LocationRemove the lower passenger under glove box trim.

locate the FEM (Forward Electrical Module) near the 'A' pillar. The CAN bus wiring is a twisted pair of wires, located in the centre white plug loom.

BMW 3 Series (E36) > 2004

Remove the vehicle speedometer assembly. The CAN wires are located at the connection plugs.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = YELLOW / BLACKCAN LO = YELLOW / BROWN

BMW 3 Series (E90) 2005 >

CAN HI = GREEN / ORANGECAN LO = GREEN

BMW 3 Series (F30) 2011 >

Vehicle CAN Bus LocationRemove the lower passenger under glove box trim.

locate the FEM (Forward Electrical Module) near the 'A' pillar. The CAN bus wiring is a twisted pair of wires, located in the centre white plug loom.

BMW 5 Series (E60) 2003 >

CAN HI = BLACKCAN LO = YELLOW

BMW 5 Series (F10-F20) 2010 >

Vehicle CAN Bus LocationRemove the drivers side lower dash trim. The CAN wires are located in a loom under the chassisbar that runs above the plastic dash pocket. Look up under the drivers side dash to find the loom.

The CAN bus wiring is a twisted pair of wires, coloured as below:

BMW 6 Series (2004>)

CAN HI = BLACKCAN LO = YELLOW

BMW 7 Series (E65/6) 2001 >

BMW 7 Series (F01-2) 2008 >

Vehicle CAN Bus LocationRemove the opening dash pocket in the lower drivers side dash (2 Torx screws). Also lower thedrivers side knee airbag for easier access (2 Torx screws). There are 2 CAN Bus connections in

the area behind, connection can be made to either (SWV 29.9 or later)

CAN HI = GREEN / ORANGE CAN LO = GREEN (In the harness clipped near the brake pedal)

CAN HI = BLUE / RED CAN LO = RED (In the vertically mounted ECU - Blue connector)

BMW GSR1200 Motorcycle

Vehicle CAN Bus LocationRemove the seat.

The CAN wiring can also be located at the harness running towards the ECUThe CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = WHITE / BLACKCAN LO = WHITE / BROWN

BMW X1 (E84) 2009 >

BMW X3 (E83) > 2011

BMW X3 (F25) 2011 >

The CAN wires are located behind the glove box in the main wiring loom.The CAN bus wiring is a twisted pair of wires, coloured as below:

BMW X5 2008 >

BMW X5 2014 >

The CAN wiring is available at the Forward Electronics Module, located behind the passengerside kick panel. The wires are located in the top white connector and are a twisted pair

detailed as below. The wiring is also available under the drivers side carpet near the sill.

CAN HI = REDCAN LO = BLUE/ RED

BMW X6 2008 >

BMW Z4 (E85) 2003 >

BMW Z4 (E89) 2009 >

BMW Mini > 2006

Remove the Rev Counter assembly. The CAN wires are located at the connection plug.The CAN bus wiring is a twisted pair of wires, coloured as below:

BMW Mini 2007 >

The CAN wiring is present at the rear of the audio unit or rev counter assembly.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN Wires may also be available in the offside A-Pillar

BMW Mini 2014 >

The CAN wiring is available at the Forward Electronics Module, located behind the passengerside kick panel. The wires are located in the top white connector and are a twisted pair

detailed as below:

CAN HI = BLUECAN LO = RED

BMW Mini Countryman

The CAN wiring is present at the rear of the audio unit or rev counter assembly.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN Wires may also be available in the offside A-Pillar

Buick Enclave

The CAN wiring is located at the OBD socket, under the drivers side dash.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = OBD Pin 1CAN LO = GROUND (OBD Pin 4)

Chevrolet Aveo : 2011 >

The CAN wiring is located at the OBD socket, under the drivers side dash.Unclip the socket for access. The CAN bus wiring is detailed as below:

CAN HI = OBD Pin 1CAN LO = Connect to Ground (0v)

Chevrolet Camaro : 2009 >

Chevrolet Captiva : 2007 >

The CAN wiring is located at the OBD socket, under the drivers side dash.Unscrew the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = OBD Pin 1CAN LO = OBD Pin 4 (Ground)

Chevrolet Colorado : 2007 >

CAN HI = Pin 6 CAN LO = Pin 14

Chevrolet Cruze : 2010 >

Chevrolet Escalade : 2007 >

CAN HI = BEIGE / BLACK (Pin 6)CAN LO = BEIGE (Pin 14)

Chevrolet HHR : 2006 >

The CAN wiring is located at the OBD socket, under the drivers side dash.Unscrew the socket for access. The CAN bus wiring is detailed as below:

CAN HI = Pin 1CAN LO = Pin 4

Chevrolet Malibu : 2008 >

CAN HI = OBD Pin 6CAN LO = OBD Pin 14

Chevrolet Orlando : 2010 >

CAN HI = OBD Pin 1CAN LO = Connect to Ground (0v) OBD Pin 4

Chevrolet Silverado : 2007 >

CAN HI = OBD Pin 1CAN LO = OBD Pin 4 (Ground)

Chevrolet Sonic : 2011 >

Chevrolet Spark : 2010 >

The CAN wiring is located at the OBD socket, under the drivers side dash.Unscrew the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

Chevrolet Volt

The CAN wiring is located at the OBD socket, under the drivers side dash.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

Chrysler 300 C < 2011

The CAN wiring is located at the radio wiring connector.Remove the dash facia panel (clipped) and unbolt the radio for access.

CAN HI = WHITE / ORANGECAN LO = WHITE (Possibly White / Red)

Chrysler 300 C 2012>

The CAN wiring is located at the LCD screen connector.Also located in the main loom behind the drivers side lower dash panel.

The CAN wiring is not twisted at the plug but may be twisted further in to the loom.

CAN HI = GREENCAN LO = WHITE

Chrysler Country 2008 >

The CAN wiring is located at the back of the radio.

CAN HI = WHITE / GREYCAN LO = WHITE / RED

Grand Cherokee 2005 >

The CAN wiring is located at the radio wiring connector and behind the climate control.Also available behind the drivers side kick panel.

CAN HI = WHITE / GREYCAN LO = WHITE / ORANGE

Grand Cherokee 2010 >

The CAN wiring is located at the radio wiring connector.Also available behind the drivers side kick panel.

CAN HI = WHITE / ORANGECAN LO = WHITE / GREY

Jeep Cherokee

Vehicle CAN Bus LocationPLEASE NOTE (Before 2007) : ONLY VEHICLES WITH MERCEDES DIESEL ENGINES HAVE CAN WIRING

The CAN wiring is located at the Engine ECU : N/S Engine bay area main loom near bulk head.The CAN bus wiring is a twisted pair of wires, coloured as below:

Models Before 2007 CAN HI = WHITE / GREEN (ECU Loom)

CAN LO = WHITE / BLUE

Models After 2007 CAN HI = WHITE / ORANGE (Radio or O/S Door Loom)

CAN LO = WHITE / GREY

Jeep Renegade 2014>

The CAN wiring is located at the OBD connector, under the drivers side dash.The CAN wiring is a twisted pair, located at the below position:

Jeep Wrangler

CAN HI = WHITE / ORANGECAN LO = WHITE

Chrysler Town 2008 >

Chrysler Voyager 2008 >

Citroen Berlingo > 2007

Vehicle CAN Bus LocationLocate the BSI module at the rear of the fuse box - drivers side dash.

The CAN bus wiring is a twisted pair of wires at the back - right hand plug, coloured as below:PLEASE NOTE : This vehicle has similar wiring as below which are not CAN wires.

The CAN wiring is at the very back corner of the BSI (40 Way Black plug) and is akward to access.Carefully pull the BSI board as far forward as possible and remove the plugs for easier access.

Citroen Berlingo 2008 >

Vehicle CAN Bus LocationThe CAN wiring is located at the audio Quadlok connector, at the rear of the audio unit.

If the vehicle does not have CAN wiring at the audio unit, an alternative CAN Bus is present at theOBD socket. The CAN Bus wiring is a twisted pair of wires detailed as below

CAN HI = Pin 10 at the audio Quadolk or Pin 6 at the OBD socketCAN LO = Pin 13 at the audio Quadlok or Pin 14 at the OBD socket

Citroen C-Crosser

No definitive installation is available for this vehicle at present.Please refer to the Mitsubishi Outlander information for comparison.

Citroen C2

Citroen C3

Citroen C4

CAN HI = Pin 10 at the audio Quadolk or BLUE (Pin 6 at the OBD socket)CAN LO = Pin 13 at the audio Quadlok or RED (Pin 14 at the OBD socket)

Citroen C5 2005 >

The CAN wiring is located at the audio Quadlock connector.The CAN bus wiring is a twisted pair of wires, detailed as below:

CAN HI = Quadlock Pin 10CAN LO = Quadlock Pin 13

Citroen C8

The CAN wiring is located at the OBD socket, inside the lower centre dash pocket.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

Citroen Dispatch 2007 >

Vehicle CAN Bus LocationRemove the audio unit to access the audio connection plugs.

Alternatively, the CAN wires can be located at the OBD socket - lower drivers side dash.The CAN bus wiring is a twisted pair of wires detailed as below:

CAN HI = WHITE (Radio) or Pin 6 (OBD Socket)CAN LO = GREY (Radio) or Pin 14 (OBD Socket)

Citroen DS3

Citroen DS4

The interface can also be connected at the OBD socket, behind the lower centre dash trim panel.The CAN Bus wiring is a twisted pair of wires detailed as below

Citroen DS5

The interface can also be connected at the OBD socket, in the bottom of the rear centre console.The CAN Bus wiring is a twisted pair of wires detailed as below

Citroen Jumper 2006 >

Vehicle CAN Bus LocationThe CAN wiring is located at the rear of the OBD socket, drivers dash fuse box behind dash panel.

The CAN bus wiring is a twisted pair of wires, coloured as below:CAN wiring may also be available at the radio. The wire location details are on the Pin-Out diagram

on the top of the radio.

CAN HI = 'CAN B' at the radio.CAN LO = 'CAN A' at the radio.

Citroen Jumper 2014 >

CAN HI = Pin 6 or Pin 1 at the OBDCAN LO = Pink 14 OR Pin 9 at the OBD

Citroen Jumpy 2008 >

CAN HI = Pin 10 at the audio Quadlock or Pin 6 at the OBD socketCAN LO = Pin 13 at the audio Quadlock or Pin 14 at the OBD socket

Citroen Nemo 2008 >

Alternatively, the CAN wires can be located at the OBD socket : Near Fuse Box - drivers side dash.The CAN bus wiring is detailed as below:

CAN HI = BLUE (Radio) OR Pin 6 (OBD Socket)CAN LO = WHITE (Radio) OR Pin 14 (OBD Socket)

Citroen Picasso

The CAN wiring is located in the R/H loom behind the glove box. Remove the glove box for access.The CAN bus wiring is a twisted pair of wires, coloured as below:

Left Hand Drive vehicles, the wiring is in the loom near the fusebox- drivers side dash.

CAN HI = BROWNCAN LO = PURPLE

Dacia Sandero

The CAN wires can be located at the OBD socket : Inside the glove compartment.The CAN bus wiring is detailed as below:

CAN HI = Pin 6 (OBD Socket)CAN LO = Pin 14 (OBD Socket)

Dacia Lodgy

The CAN wires can be located at the OBD socket : Lower drivers side dash.The CAN bus wiring is detailed as below:

DAF General J-1939

The CAN wires are located under the N/S lower dash trim, in a loom running left to right.The CAN bus wiring is a twisted pair of wires coloured as below:

CAN HI = BLUECAN LO = YELLOW

Dodge Caliber

Also located in the main loom behind the drivers side lower dash kick panel.

CAN HI = WHITE / ORANGECAN LO = WHITE or WHITE / PURPLE

Dodge Caravan < 2007

Dodge Caravan 2008 >

Dodge Charger 2015>

The CAN wires can be located at the OBD socket : Lower drivers side dash.The CAN bus wiring is detailed as below:

Dodge Challenger < 2011

The CAN wiring is located at the radio wiring connector.Remove the dash facia panel (clipped) and unbolt the radio for access.Also located in the main loom behind the drivers side lower dash panel.

Dodge Challenger 2012>

The CAN wiring is located at the radio wiring connector.Remove the dash facia panel (clipped) and unbolt the radio for access.Also located in the main loom behind the drivers side lower dash panel.

Dodge Dart : 2013 >

The CAN wires can be located at the OBD socket, lower drivers side dash.Connection may also be possible at the rear of the radio - no details at present.

The CAN bus wiring is detailed as below:

CAN HI = PIN 3 OBD SocketCAN LO = PIN 11 OBD Socket

Dodge Durango

CANM8 RAM Installation File

Dodge Ram < 2013

Dodge Ram 2013 >

Ferrari F430 : 2006 >

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD socket, drivers dash fuse box behind dash panel.

Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = PIN 6CAN LO = PIN 14

Fiat Bravo 2007 >

CAN HI = PIN 6 (Pink / Black)CAN LO = PIN 14 (Pink / White)

Fiat Croma

Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:CAN wiring is also available at the radio. The wire location details are on the Pin-Out diagram

CAN HI = PIN 6 (Pink / Black - Unconfirmed) or 'CAN B' at the radio.CAN LO = PIN 14 (Pink / White - Unconfirmed) or 'CAN A' at the radio.

Fiat Doblo : > 2011

Fiat Doblo : 2012 >

Alternatively, the CAN wires can be located at the OBD socket : Near Fuse Box - drivers side dash.Connection may also be possible at the rear of the radio - no details at present.

Fiat Ducato 2006 >

The CAN bus wiring is a twisted pair of wires, coloured as below:CAN wiring may also be available at the radio. The wire location details are on the Pin-Out diagram

CAN HI = 'CAN B' at the radio.CAN LO = 'CAN A' at the radio.

Fiat Ducato : 2014 >

Fiat Fiorino : 2008 >

Fiat Freemont : 2012 >

Alternatively, the CAN wires can be located at the OBD socket : Near Fuse Box - drivers side dash.Connection may also be possible at the rear of the radio - no details at present.

Fiat Grande Punto

CAN HI = PIN 6 (Pink / Black)CAN LO = PIN 14 (Pink / White)

Fiat Panda

Fiat Scudo 2007 >

Fiat Stilo

Fiat Viaggio : 2013 >

Fiat 500

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD socket, drivers dash behind dash panel.The CAN Bus can also be located at the rear of the speedometer or audio unit

The CAN bus wiring is a twisted pair of wires, detailed as below:

CAN HI = PIN 6 OBD Socket OR BLUE Wire at the speedometer / audio unitCAN LO = PIN 14 OBD Socket OR WHITE Wire at the speedometer / audio unit.

Fiat 500 X

Fiat 500L 2013 >

CAN HI = OBD Pin 1 (Blue)CAN LO = OBD Pin 9 (White)

Ford B-Max 2012 >

Ford Ecosport 2013 >

Ford Escape (USA) : 2008 >

Ford Expedition 2007 >

Ford F150 / F250

Ford F350 2006 >

Ford F350 2011 >

Ford Fiesta >2007

The CAN wiring is located at the OBD socket, lower drivers side dash and at the audio Quadlok***

Connect to Pins 6 & 14 for installations that require an RPM output.***Early Fiesta models may not feature this CAN Bus system.

***CAN Bus Option 1 (Non RPM) : CAN HI = Quadlock Pin 9 CAN LO = Quadlok Pin 10CAN Bus Option 2 (RPM Applications) : CAN HI = Pin 6 CAN LO = Pin 14

Ford Fiesta 2008 >

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD socket, lower drivers side dash and at the radio Quadlock***

OBD Connection : CAN HI = OBD Pin 3 CAN LO = OBD Pin 11

Radio Connection : CAN HI = Quadlock Pin 9 CAN LO = Quadlok Pin 10

Ford Fiesta 2013 >

Ford Focus & C-Max : 2005 >

Ford Focus & C-Max : 2011

Ford Fusion

CAN HI = GREY / REDCAN LO = BLUE / RED

CANM8-NAV Installation File

Ford Fusion (USA) : 2010 >

CANM8-NAV Wiring Instructions

CANM8-PARK Wiring Instructions

The CANM8 interface switches on automatically when CAN activity is detected.The interface has an LED status indicator next to the connection plug, which will flash constantly

when a CAN signal is present and has been identified by the interface.

If the LED indicator is illuminated costantly, the interface is functioning but cannot identify thesubject vehicle. It is very important that the interface is only connected to the vehicle CAN Bus

wiring at the connection point location detailed at the top of the page.

If the LED fails to illuminate or flash, the interface wiring has been connected incorrectley orno CAN activity has been detected. Check all electrical connections are sound and that the

interface CAN HI and CAN LO connections are the correct way around. Also check that there isa good 12v supply present at the interface plug-in connector before seeking technical assistance.

The CANM8 interface automatically switches off when the vehicle CAN Bus is inactive.This can be tested by removing the keys from the ignition, closing all vehicle doors and

Ford Galaxy : 2006 >

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD socket, under the drivers side dash. Unclip the socket to access.

The CAN wiring can also be accessed at the audio unit Quadlock connector.The CAN wiring is a twisted pair of wiresa coloured as below:

CAN HI = Quadlock Pin 11 - Blue / Grey (or OBD PIN 1)CAN LO = Quadlock Pin 10 - Purple / Grey (or OBD PIN 8)

Note : RPM is only available on the High Speed CAN Bus : Hi = OBD Pin 6 - LO = OBD Pin 14

Ford Galaxy 2015 >

The CAN wiring is located at the rear of the OBD socket, under the drivers side dash, also availablebehind the passenger kick panel. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = GREY/ORANGE wire in the harness leading to the OBD socket.CAN LO = PURPLE/ORANGE in the harness leading to the OBD socket.

Ford KA 2008 >

Ford Kuga 2009 >

Ford Kuga 2013 >

Ford Mondeo 2004 >

The CAN wiring is also present at the audio unit Quadlock connector.

Ford Mondeo 2007 >

The CAN wiring is located at the OBD socket, under the drivers side dash, also at the audio plug.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = Quadlock Pin 11 - Blue / Grey (or OBD PIN 3)CAN LO = Quadlock Pin 10 - Purple / Grey (or OBD PIN 11)

Ford Mondeo 2015 >

The CAN wiring is located in the harness at the rear of the OBD socket, under the drivers side dash also available behind the passenger kick panel.

The CAN Bus wiring is a twisted pair of wires coloured as below:CAN HI = Grey/Orange wire in the harness leading to the OBD socket.

CAN LO = Purple/Orange wire in the harness leading to the OBD socket. or CAN HI = White/Blue CAN LO = WHITE in the same location.

Ford Mustang

CAN HI = WHITE / REDCAN LO = PINK / RED

Ford Ranger 2012 - 2016

Ford Ranger 2016 >

Ford Focus S- Max

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD socket, inside the drivers side dash pocket.

Connect to pins 3 & 11 for installations that do not need an RPM output.Connect to Pins 6 & 14 for installations that require an RPM output.

CAN wiring is also present at the radio Quadlock

CAN Bus Option 1 (Non RPM) : CAN HI = Pin 3 CAN LO = Pin 11CAN Bus Option 2 (RPM Applications) : CAN HI = Pin 6 CAN LO = Pin 14

Ford Transit 2006 >

Remove the vehicle audio unit or speedo or connect at the OBD socket below the drivers side dash. The CAN bus wiring is a twisted pair of wires, coloured as below:

The CAN bus wiring can also be located at the OBD socket, drivers side lower dash area.Note : RPM is only available on the High Speed CAN Bus : Hi = OBD Pin 6 - LO = OBD Pin 14

CAN HI = BLUE / GREY (Audio Quadlock Pin 9) OR OBD Connector Pin 3CAN LO = PURPLE / GREY (Audio Quadlock Pin 10) OR OBD Connector Pin 11

Ford Transit 2014 >

Remove the vehicle audio unit or speedo or connect at the OBD socket below the drivers side dash. The CAN bus wiring is a twisted pair of wires, coloured as below:

The CAN bus wiring can also be located at the OBD socket, drivers side lower dash area.Note : RPM is only available on the High Speed CAN Bus : Hi = OBD Pin 6 - LO = OBD Pin 14

CAN HI = OBD Connector Pin 3CAN LO = OBD Connector Pin 11

Ford Transit Connect 2006 >

Ford Transit Custom 2013 >

GM Single Wire CAN

Vehicle CAN Bus LocationAvailable on NAV software issues from 25.6 and PARK from 24.6 and onward.

The CAN wiring is located at the OBD socket, under the drivers side dash or centre console.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = PIN 1 - OBD SocketCAN LO = 0v (Ground)

GMC Canyon 2007 >

GMC Yukon Denali 2007 >

J1939 Applications

This profile is available to all vehicles using J1939 CAN information.The CAN bus wiring is a twisted pair of wires, usually found at the rear of the speedometer or at

the main electrical fuse / relay assembly.

CAN HI = Vehicle dependent (see individual manufacturer files if available.)CAN LO = Vehicle dependent (see individual manufacturer files if available.)

Honda Accord 2003 - 2008

CAN HI = WHITECAN LO = RED

Honda Accord 2008 >

The CAN wires are located at the OBD SocketThe CAN bus wiring is a twisted pair of wires, coloured as below:

Honda Civic

Honda Crossroad

Locate the CAN Bus wiring at the rear of the vehicle speedometer or at the OBD socket.The OBD socket is located at the lower drivers side dash.

CAN HI = WHITE - Pin 2 - Speedo plug OR Pin 6 - OBD SocketCAN LO = RED- Pin 3 - Speedo plug OR Pin 14 OBD Socket

Honda CR-V 2007 >

Vehicle CAN Bus LocationRemove the vehicle speedometer assembly. The CAN wires are located at the connection plugs.

Alternatively, the CAN wires can be located at the OBD socket - lower drivers side dash.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = WHITE (Speedo Plug) or Pin 6 (OBD Socket)CAN LO = RED (Speedo Plug) or Pin 14 (OBD Socket)

Honda CR-V 2012 >

The CAN wires are located at the OBD socket - lower drivers side dash.The CAN bus wiring is a twisted pair of wires, detailed as below:

Honda CR-Z 2010 >

The CAN wires can be located at the OBD socket - lower drivers side dash.The CAN bus wiring is a twisted pair of wires, detailed as below:

Honda Element

Honda Freed 2008 >

Honda FR-V 2006 >

Honda Insight 2009 >

The CAN wires can be located at the OBD socket - lower drivers side dash or at the speedometer.The CAN bus wiring is a twisted pair of wires, coloured as below:

Honda Jazz 2009 >

The CAN wires can be located at the OBD socket - lower drivers side dash or at the speedometer.The CAN bus wiring is a twisted pair of wires, coloured as below:

Honda Odyssey 2004 >

CAN HI = WHITE - Pin 6- Large Green Speedo plug OR Pin 6 - OBD SocketCAN LO = RED- Pin 7 - Large Green Speedo plug OR Pin 14 OBD Socket

Honda Stepwagon 2006 >

CAN HI = Pin 6 OBD SocketCAN LO = Pin 14 OBD Socket

Honda Stream 2006 >

The CAN bus wiring is a twisted pair of wires, detailed as below:

CAN HI = Pin 6 OBD SocketCAN LO = Pin 14 OBD Socket

Hummer H2 : 2007 >

CAN HI = BROWN / BLACK (Pin 6)CAN LO = BROWN (Pin 14)

Hyundai i-10

CAN HI = OBD Socket - PIN 6CAN LO = OBD Socket - PIN 14

Hyundai i-20

Hyundai i-30

Hyundai i-40

Hyundai ix-35

Hyundai Veloster

Hyundai H1-i800-iLoad

Infinity FX35

Infinity FX45

CAN HI = BLUE (Pin 6)CAN LO = RED (Pin 14)

Isuzu D-Max : 2012 >

The CAN wires can be located at the OBD socket under the drivers side dash.The CAN bus wiring is detailed as below:

Iveco Daily : 2006 >

The CAN Bus wiring is located at the radio ISO connectros.Please refer to the PIN OUT diagram on the radio for confirmation of locations.

CAN HI = Wire marked 'CAN B' at the radio.CAN LO = Wire marked 'CAN A' at the radio.

Iveco Daily : 2014 >

The CAN Bus wiring is located at the OBD Socket

Jaguar F 2013 >

The CAN wiring is located at the OBD socket, under the drivers side dash, near the kick panel.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

CAN HI = OBD Socket - PIN 3 CAN LO = OBD Socket - PIN 11

Jaguar S-Type 2004 >

Jaguar X-Type

Jaguar XF 2008>

CAN HI = OBD Socket - PIN 3 (Alternatively use Pin 6)CAN LO = OBD Socket - PIN 11 (Alternatively use Pin 14)

Jaguar XE 2015 >

CAN HI = OBD Socket - PIN 3 CAN LO = OBD Socket - PIN 11

Jaguar XJ6-XJ8

The CAN wiring is located at the OBD socket, under the drivers side dash, near centre console.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = YELLOW (PIN 6)CAN LO = GREEN (PIN 14)

Jaguar XK-R >2007

The CAN wiring is located at the OBD socket, under the drivers side dash, near the kick panel.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

Jaguar XK-R 2008>

The CAN wiring is located at the OBD socket, under the drivers side dash, near the kick panel.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

Kia Carens

Kia Ceed

Kia Picanto : 2011 >

Kia Sorento 2009 >

Kia Soul

Kia Sportage 2010 >

Kia Venga

Lamborghini Galardo

Remove the lower passenger side under panel. The CAN wires are located at the loom near fuse board.

Lancia Delta

Lancia Musa

Lancia Thema 2011 >

Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, detailed below:

CAN HI = OBD PIN 3CAN LO = OBD PIN 11

Lancia Thesis

Vehicle CAN Bus LocationCAN wiring is also available at the radio. The wire location details are on the Pin-Out diagram

on the top of the radio.Connection can also be made at the OBD socket, in the fusebox under the drivers dash.

***Use an OBD connection plug - contact sales for details.

CAN HI = 'CAN B' at the radio OR Pin 6 at the OBD***CAN LO = 'CAN A' at the radio OR Pin 14 at the OBD***

Lancia Ypsilon

Land Rover Defender 2007>

CAN HI = BLUE / BLACKCAN LO = GREEN / BLACK

Land Rover Discovery 3

Locate the OBD socket, lower drivers side dash. The loom can be pulled down for wire access.If CAN wires are in positions 3 & 11, use option 1 - otherwise use option 2.

Option 1: CAN HI = PIN 3CAN LO = PIN 11

Land Rover Discovery 4

Locate the OBD socket, lower drivers side dash. The loom can be pulled down for wire access.The CAN wiring is detailed as below:

Land Rover Evoque

Land Rover Freelander

Land Rover Freelander 2

Locate the OBD socket, lower drivers side dash or connect at the adusio connector.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = Grey / Orange (OBD Pin 3)CAN LO = Purple / Orange (OBD Pin 11)

Land Rover Range Rover

Vehicle CAN Bus LocationVehicles from 2005 >

Option 2: CAN HI = YELLOW / BLACK - PIN 6CAN LO = YELLOW / BROWN - PIN 14

Land Rover Range Rover 2013

FOR RPM OUTPUT CONNECT AT CAN HI = PIN 6 AND CAN LO = PIN 14

Land Rover RRover Sport < 2014

Option 2: CAN HI = YELLOW / BLACK - PIN 6CAN LO = YELLOW / BROWN - PIN 14

Land Rover RRover Sport 2014 >

Locate the OBD socket, lower drivers side dash. The loom can be pulled down for wire access.The CAN wires are detailed below:

Lexus is250

Locate the OBD socket, lower drivers side dash. The loom can be pulled down for wire access.The CAN bus wiring is a twisted pair of wires, detailed as below:

Lexus RX350 2009 >

Lexus RX400-450H 2009 >

Lincoln Town Car

MAN - General J1939

The CAN wires are located at the near side, on the top of an ECU in a White connector.The CAN bus wiring is a twisted pair of wires coloured as below:

CAN HI = BLUE / REDCAN LO = BLUE / WHITE

Mazda '2'

The CAN wiring is located at the OBD socket, lower drivers side dash area.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

Mazda '3'

Mazda '5'

Connect the interface to a switched 12v+ supply on this vehicle !!!!

Mazda '6' 2005 >

Newer vehicles may also feature a 2nd CAN system:

CAN HI = PIN 6 CAN LO = Pin 14

Mazda '6' 2012 >

Mazda CX-5

CAN HI = PIN 3 CAN LO = PIN 11

Mazda CX-7

Mazda CX-9

Mazda Demio 2005 >

The CAN wiring is located at the OBD socket, lower drivers side dash or the speedometer wiring.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

CAN HI = PIN 6 (RED at the speedometer)CAN LO = PIN 14 (WHITE at the speedometer)

Mazda MPV 2005 >

CAN HI = PIN 6 (Blue / White)CAN LO = PIN 14 (Green / Black)

Mazda MX-5 2006 >

CAN HI = PIN 6 (Blue / White)CAN LO = PIN 14 (Green / Black)

Mazda RX-8

Mazerati Gran Turismo

CAN HI = BLACK / PINKCAN HI = WHITE / PINK

Mercedes A-Class >2004

Vehicle CAN Bus LocationThe CAN wiring is located at the speedometer connection plugs.

Remove the lower drivers side under panel. The speedometer cover retaining screws are beneath.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = WHITE CAN LO = GREEN

Mercedes A-Class 2005>

The CAN wires are located at the audio unit and in the main wiring looms.The CAN bus wiring is a twisted pair of wires, coloured as below:

Preferred connection : CAN HI = BROWN / RED CAN LO = BROWNAlternative connection : CAN HI = WHITE CAN LO = GREEN

Mercedes A-Class 2012>

The CAN wires are at the audio unit and in the drivers side sill loom (8 Way Black Connector).The CAN bus wiring is a twisted pair of wires, coloured as below:

Preferred connection : CAN HI = BROWN / RED CAN LO = BROWNAlternative connection : CAN HI = GREEN / WHITE CAN LO = GREEN

Mercedes Actros

The CAN wires are located at the audio unit.The CAN bus wiring is a twisted pair of wires in a Purple connector, coloured as below:

The CAN wires are also at the right of the fuse box at the lower left below the main power cable.

Mercedes Atego

The CAN wires are located in the right of the fuse box in a Grey connector.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes Axor

The CAN wires are located in the right of the fuse box in a Grey connector.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes B-Class 2005>

Vehicle CAN Bus LocationThe CAN wires are located at the audio unit and in the main wiring looms.

Check for a CAN Network Junction Connector under the O/S dash.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes B-Class 2011>

CAN HI = BROWN / REDCAN LO = BROWN

Mercedes C - Class

Vehicle CAN Bus LocationRemove the lower drivers side under panel. Locate the ignition barrel loom or control unit loom.A choice of 2 Bus systems is available, the wiring is a twisted pair of wires, coloured as below:

Important ! Use one Bus or the other, do not cross connect the two Buses!!!

Preffered Connection : CAN HI = BROWN / RED CAN LO = BROWN

CAN HI = GREEN / WHITE CAN LO = GREEN

Mercedes C - Class 2007 >

The CAN Bus can be located within the plastic loom channels beneath the drivers side carpet.Also located in the centre console loom - drivers side and other locations.

Note: If Reverse Gear Output is required, use Bus 1 for Manual and Bus 2 for Automatic cars.Otherwise, connect to Bus 1.

CAN Bus 1: CAN HI = BROWN / RED CAN LO = BROWNCAN Bus 2: CAN HI = GREEN CAN LO = WHITE

Mercedes C - Class 2014 >

The CAN Bus can be located within the plastic loom channels beneath the drivers side carpet.Remove the sill trim for access.

Mercedes CLK

Remove the lower drivers side under panel. The CAN wires are located at the lower wiring loom.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes CLS 2004 >

The CAN wires are located at the wiring loom below the steering coloumn.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes CLS 2011 >

The CAN wires are located at the lower wiring loom behind the carpet near to the park brake.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes E Class (210) 2000 >

The CAN wires are located behind the lower passenger side kick panel.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes E - Class (211) 2002 >

Remove the lower drivers side under panel. Locate the ignition barrel loom or control unit loom.The wiring is a twisted pair of wires, coloured as below:

CAN HI = BROWN / RED CAN LO = BROWN

Mercedes E - Class (212) 2009 >

Vehicle CAN Bus LocationRemove the N/S kick panel

The CAN Bus wiring is a twisted pair of wires, coloured as below:

Mercedes G 1990 >

The CAN wires are located at the ABS module.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes GL 2006 >

Remove the passenger side kick panel. The CAN wires are located at the lower wiring loom.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes GLA 2014 >

The CAN Bus wiring is located at the rear of the light switch.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes GLK 2008 >

The CAN wires are located at the lower wiring loom behind the carpet near to the park brake.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes M-Class W163 >2005

Remove the lower drivers side under panel. The CAN wires are located at the control module.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes M Class (164) 2006 >

The CAN Bus can be located at the rear of the audio unit.Carefully unclip the heater control panel and pull down the 2 metal retaining clips behind to remove.

Mercedes M Class (166) 2011 >

The CAN Bus can be located at the rear of the audio unit or the ignition module.The same wiring may also be present in other dash and front to rear harnesses.

Mercedes R-Class (251) 2006>

Mercedes S-Class 221

Vehicle CAN Bus LocationRemove the lower drivers side under panel. The CAN wires are located at the CAN junction.

Mercedes S Class (222)

Unscrew the under panel cover near the bonnet release lever on the drivers side.The panel will pivot down to expose a module and wiring. Locate the CAN wiring as below:

CAN HI = Yellow / WhiteCAN LO = Yellow

Mercedes SL (R230) 2003 >

The CAN wiring is located at the igntion key module and may also be in other main harnesses.The CAN Bus wiring is a twisted pair of wires as detailed below:

Mercedes SL (R231) 2012 >

Mercedes SLK R171 2004 >

Mercedes Sprinter > 2006

Remove the vehicle speedometer cover. The CAN wires are located at the connection plugs.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = GREEN / WHITE CAN LO = GREEN

Mercedes Sprinter 2007 >

Remove the drivers side lower dash panel and locate the wiring to the ignition key module.The CAN bus wiring is a twisted pair of wires coloured as below:

Also available at the audio ISO or Quadlock connectors

Mercedes Sprinter 2015 >

Remove the drivers side lower dash panel and locate the wiring to the ignition key module.The CAN bus wiring is a twisted pair of wires coloured as below:

Mercedes V-Class 2014

Remove the lower drivers side under panel. The CAN wires are located at near the kick panel.Also at the igntion key module. The CAN bus wiring is a twisted pair of wires, coloured as below:

Mercedes Viano / Vito

Remove the lower drivers side under panel. The CAN wires are located at near the kick panel.Also at the speedometer. The CAN bus wiring is a twisted pair of wires, coloured as below:

Early models may not have the BROWN CAN Bus

Mercedes Vito 2015

Remove the lower drivers side under panel. The CAN wires are located at near the kick panel.Also at the igntion key module. The CAN bus wiring is a twisted pair of wires, coloured as below:

MG 6 Dti 2011 >

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD connector.

Remove the drivers side lower dash pocket for access.The CAN bus wiring is a twisted pair of wires, coloured as below:

Mitsubishi ASX 2010 >

The CAN Bus can be located at the rear of the speedometer or audio unit.The CAN bus wiring is a twisted pair of wires, detailed as below:

CAN HI = RED (Speedometer Connector Pin 23)CAN LO = PINK (Speedometer Connector Pin 22)

Mitsubishi Colt

Remove the lower drivers side dash panel. The CAN wires are located at the OBD Socket.The CAN bus wiring is a twisted pair of wires, detailed as below:

Mitsubishi Grandis

The CAN wires are located at the OBD Socket - Lower drivers side dash. Also at the rear of speedoThe CAN bus wiring is a twisted pair of wires, detailed as below

CAN HI = OBD Pin 6 (RED / BLUE at speedo - PIN 4 opposite the plug catch)CAN LO = OBD Pin 14 (BLACK / BLUE at speedo - PIN 3 opposite the plug catch)

Mitsubishi Lancer Evo 10 2008>

The CAN Bus wiring is located at the rear of the speedometer.The CAN bus wiring is a twisted pair of wires, detailed as below:

CAN HI = GREEN CAN LO = PINK

Mitsubishi L200 (2006>)

The CAN wires are located at the OBD Socket, under the drivers side dash.The CAN bus wiring is a twisted pair of wires, detailed as below:

This vehicle is not supported after SWV 28.9 - Please contact Technical support.

Mitsubishi L200 (2012>)

The CAN wires are located at the OBD Socket, under the drivers side dash.The CAN bus wiring is a twisted pair of wires, detailed as below:

Mitsubishi Outlander 2007>

The CAN Bus wiring is located at the rear of the speedometer and at the audio wiring connectorThe CAN bus wiring is a twisted pair of wires, detailed as below:

CAN HI = GREEN (Behind speedometer) OR ORANGE (Behind radio)CAN LO = PINK (Behind speedometer) OR WHITE (Behind radio)

Mitsubishi Outlander 2013 >

The CAN Bus wiring is located at the OBD Connector, under the lower drivers side dash.The CAN bus wiring is a twisted pair of wires, detailed as below:

Mitsubishi Space Star 2013 >

The CAN Bus wiring is located at the OBD Connector, under the lower drivers side dash.The CAN bus wiring is a twisted pair of wires, detailed as below:

Nissan 350Z

Nissan 370Z

Nissan Almera

Remove the vehicle speedometer assembly. The CAN wires are located at the large multi plug.The CAN bus wiring is a twisted pair of wires, coloured as below:

Nissan Altima

Nissan Cube

Remove the vehicle speedometer assembly or connect at the OBD socket - drivers side dash.The CAN bus wiring is a twisted pair of wires, coloured as below (later models change colour):

CAN HI = RED or BLUE (late models) or OBD Pin 6CAN LO = WHITE or PINK (late models) or OBD Pin 14

Nissan Elgrand 2002 >

Connect at the rear of the speedometer or at the OBD socket - drivers side lower dash.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = PINK - Pin 4 at Speedo OR Pin 6 at OBD socketCAN LO = BLUE - Pin 5 at speedo OR Pin 14 at OBD Socket

Nissan Juke 2010 >

Nissan Leaf 2011 >

Nissan Micra

The CAN wiring is also available at the rear of the speedo in pins 1 & 2.Unclip both 'A' pillar trims and the dash lid for access to the rear of the speedo.

CAN HI = RED : Pin 6CAN LO = WHITE : Pin 14

Nissan Murano

Nissan Navarra

Nissan Note

Nissan NV 200 2010>

Nissan NV400 2010 >

The CAN wiring is located at the OBD socket, inside the glove box.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

Nissan Pathfinder

Nissan Pixo

Nissan Primastar

The CAN wiring is located at the OBD socket, under the steering column.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

Nissan Primera

Nissan Qashqai

Nissan Rogue

Nissan Sentra

Nissan Skyline / 350GT

Nissan X-trail 2004-2007

CAN HI = WHITECAN LO = RED

Nissan X-Trail 07-14

Nissan X-Trail 2014 >

Opel GT : 2007 >

Peugeot 206 2002 >

The CAN bus wiring is a twisted pair of wires at the coloured as below:

CAN HI = BROWNCAN LO = PURPLE

Peugeot 207

The CAN wiring is located at the OBD socket under the drivers dash and also at the radio Quadlock. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = OBD Pin 6 OR at the Quadlock RED wireCAN LO = OBD Pin 14 OR at the Quadlock : BLUE wire

Peugeot 208 : 2012 >

CAN HI = OBD Pin 6 OR at the Radio Quadlock Pin 10CAN LO = OBD Pin 14 OR at the Radio Quadlock Pin 13

Peugeot 2008

Locate the OBD socket, lower drivers side dash. Remove the fuse box cover panel for access.The loom can be pulled down for wire access. An alternative CAN Bus is available at the audio.

Peugeot 307 All Models

Remove the lower passenger side under panel. The CAN wires are located at the BSI module.The CAN bus wiring is a twisted pair of wires on a black multi-plug, coloured as below:

CAN HI = GREENCAN LO = GREY

Peugeot 308 : 2007 >

Peugeot 407

Remove the lower passenger side under panel. The CAN wires are located at a white multi-plug.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = WHITECAN LO = GREY

Peugeot 4007

No definitive installation is available for this vehicle at present.Please refer to the Mitsubishi Outlander infor mation for comparison.

Peugeot 508 : 2011 >

The CAN wiring is located at the OBD socket under the ashtray and also at the radio Quadlock. The CAN bus wiring is a twisted pair of wires, coloured as below:

Peugeot 5008

Locate the OBD socket, lower drivers side dash. Remove the fuse box cover panel for access.The loom can be pulled down for wire access. An alternative CAN Bus is available at the audio.

Peugeot 607 : 2000 >

The CAN wiring is located at the BSI Module (Fuse Box). Locate the Black connector that hasGreen and Brown inserts. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = Brown Insert, Pin 1 (Beige wire)CAN LO = Brown Insert, Pin 3 (Red wire)

Peugeot 607 : 2005 >

The CAN wiring is located at the OBD socket, inside the lower centre dash pocket and also at the radio Quadlock. The CAN bus wiring is a twisted pair of wires, coloured as below:

Peugeot 807 > 2005

The CAN wiring is located in a wiring loom - behind drivers side dash.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = WHITECAN LO = PURPLE

Peugeot 807 2006>

The CAN wiring is located at the OBD socket, inside the lower centre dash pocket and also at the radio Quadlock. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = OBD Pin 6 OR at the Quadlock WHITE wireCAN LO = OBD Pin 14 OR at the Quadlock : YELLOW wire

Peugeot Bipper : 2008 >

Peugeot Boxer : 2006 >

Peugeot Boxer : 2014 >

CAN HI = PIN 6 or PIN 1 at the OBDCAN LO = Pin 14 or PIN 9 at the OBD

Peugeot Expert 2007 >

Alternatively, the CAN wires can be located at the OBD socket - lower drivers side dash.The CAN bus wiring is a twisted pair of wires detailed as below:

CAN HI = WHITE (Radio) or Pin 6 (OBD Socket)CAN LO = GREY (Radio) or Pin 14 (OBD Socket)

Peugeot Partner > 2007

The CAN bus wiring is a twisted pair of wires at the back - right hand plug, coloured as below:PLEASE NOTE : This vehicle has similar wiring as below which are not CAN wires.

The CAN wiring is at the very back of the BSI and can be akward to access.Carefully pull the BSI board as far forward as possible for easier access.

Peugeot Partner 2008 >

Peugeot RCZ

The CAN wiring is also available at the Black BSi (Fuse Box) connector under the drivers dash.The CAN Bus wiring is a twisted pair of wires detailed as below

CAN HI = Pin 10 at the audio Quadolk or Pin 21 (Yellow) at the Black Bsi connector.CAN LO = Pin 13 at the audio Quadlok or Pin 24 (Violet) at the Black Bsi connector.

Porsche Boxster > 2004

The CAN bus wiring is a twisted pair of wires at the GREEN plug, coloured as below.Remove the Hazard Switch Lens on the left of the dash and also the small round vent type coverto the right of the dash - remove both Torx fixings at the rear of them. Then lift the dash upwards.

CAN HI = WHITE / BLUECAN LO = WHITE / GREY

Porsche Boxster 2004 >

Remove the drivers side kick trim which houses the fuse box. The CAN wiring is located in themain loom to the side. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = YELLOWCAN LO = BLACK

Porsche Cayenne

Locate the main front-to-rear loom behind the drivers side kick panel carpet.The CAN bus wiring is a twisted pair of wires, coloured as below:

Also may be available in the loom at the rear of the headlamp switch.

Porsche Cayman

Porsche 911 (996) : 2001>

Remove the speedometer assembly. The CAN wiring is located in theGreen 32 Way connector. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = Grey / White - Pin 31CAN LO = Blue / White - Pin 15

Porsche 911 (997) 2005 >

Renault Clio 2005 >

Renault Clio 2012 >

The CAN wiring is located at the OBD socket, lower centre daswh behind a cover.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

Renault Espace

The CAN wiring is located at the OBD socket, under a cover between the 2 front seats.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

Renault Fluence 2009 >

The CAN wiring is located at the OBD socket, under the cup holder in the below the centre arm rest.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

Renault Kangoo 2008 >

The CAN wiring is located at the OBD socket, in the centre console, under a trim cover.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

Renault Kangoo 2003 >

The CAN wiring is located at the OBD socket, in the fuse compartment (passenger dash area).Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

Renault Koleos

Renault Laguna > 2007

The CAN wiring is located at the OBD socket, under a rubber cover below the ashtray.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

Renault Laguna 2008 >

The CAN wiring is located at the OBD socket, under the cup holder in the below the centre arm rest.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

Renault Master > 2008

The CAN wiring is located at the OBD socket, behind the drivers side lower dash panel.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

Renault Master 2009 >

The CAN wiring is located at the OBD socket, inside the glove compartment.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

Renault Megane > 2008

CAN HI = PINKCAN LO = BROWN / WHITE

Renault Megane 3 : 2009 >

The CAN wiring is located at the OBD socket, under the radio behind a plastic panel.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

Renault Modus

CAN HI = ORANGECAN LO = BROWN

Renault Scenic 2003>

Remove the vehicle speedometer assembly. The CAN wires are located at the connection plugs.Also available at the OBD connector, under a cover between the front seats.

CAN HI = BROWN / WHITE Or OBD Pin 6CAN LO = ORANGE / WHITE or OBD Pin 14

Renault Scenic : 2009 >

The CAN wiring is located at the OBD socket, under the centre console - slide back to access.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

Renault Traffic

Renault Vel Satis 2002 >

The CAN wiring is located at the OBD socket, under a rubber cover below the ashtray.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

Renault Wind : 2010 >

The CAN wiring is located at the OBD socket in the glove box.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, identified as below:

Renault Zoe

The CAN wiring is located at the OBD socket, behind a cover in the lower centre dash area.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, coloured as below:

Rover 75 / MG-ZT(T)

Rover 75 (V8 Engine)

Saab 93 2006 >

Locate the OBD socket under the drivers side dash area.Connect the interface as below

CAN HI = Pin 1 (Single wire CAN)CAN LO = Pin 4 (Ground Connection)Alternative connection : CAN HI = Pin 6

Alternative connection : CAN LO = Pin 14

Saab 95 : 2006 >

Remove the vehicle Glove Box. The CAN wires are located at the Left Hand Main Loom.The CAN bus wiring is a twisted pair of wires, coloured as below:

Saab 95 : 2010 >

Remove the vehicle Glove Box. The CAN wires are located at the Left Hand Main Loom.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = OBD Pin 1 (Green)CAN LO = OBD Pin 4 (Black)

Scania General J-1939

The CAN wiring can be found in the main loom under the passenger fuse box and also atthe speedometer assembly. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = YELLOWCAN LO = WHITE

Seat Alhambra

Vehicle CAN Bus LocationThe CAN wires are located at the GREEN connector located at the rear of the speedometer. Remove the steering

column housing. There are 2 x Torx screws securing the speedometer. Remove these and insert a plastic lever tool at

the top edge of the speedometer glass. Lever the speedo forward to release. There are 2 sets of CAN wiring at the

connection plug - only one set carries the CAN data! The CAN wiring is a twisted pair coloured as below :-

Later models may also feature the CAN wiring at the radio (top ISO connector):-

CAN HI = ORANGE / BLACK CAN LO = ORANGE / BROWN

Seat Altea > 2007

CAN HI = YELLOWCAN LO = BROWN

Seat Altea 2008 >

Vehicle CAN Bus LocationRemove the lower drivers side under panel. The CAN wires are located at a 12 way multi-plug.

The CAN wires can also be located at the rear of the audio unit.The CAN bus wiring is a twisted pair of wires, coloured as below:

Under Dash : CAN HI = ORANGE / GREEN Radio : CAN HI = ORANGE / PURPLE Under Dash : CAN LO = ORANGE / BROWN Radio : CAN LO = ORANGE / BROWN

Seat Exeo 2009 >

Seat Ibiza 2003 >

Seat Ibiza 5 2008 >

The CAN Bus wiring is located at the steering column loom.The CAN bus wiring is a twisted pair of wires, coloured as below:

Seat Ibiza 6 2012 >

Seat Ibiza 7 2015 >

Seat Leon 2005 >

Seat Leon : 2014 >

CAN HI = ORANGE / GREENCAN LO = ORANGE / BROWN - Also located at Pin 17 (BCM Brown plug - Rear of fuse box)

Skoda Fabia

Remove the speedometer assembly. The CAN wires are located at the wiring plug.The CAN bus wiring is a twisted pair of wires, coloured as below:

Skoda Octavia 05 >

Remove the lower drivers side under panel. The CAN wires are located at a 12 way multi-plug.The CAN bus wiring is a twisted pair of wires, coloured as below:

Skoda Octavia II 09 >

The CAN wiring may also be present in other looms at the front and back of the car.

CAN HI = ORANGE / GREEN *CAN LO = ORANGE / BROWN

* Connection can also be made at the audio connector - the HI wire will be ORANGE / PURPLE

Skoda Octavia III 2013 >

Connection can also be made in the door looms.

Skoda Rapid 2013 >

Connection can also be made in the harness behind the driver side kick panel (lower 'A' trim).

Skoda Roomster 09 >

CAN HI = ORANGE / PURPLE *CAN LO = ORANGE / BROWN

* When connecting in other looms (Steering Column) the HI wire may be ORANGE / GREEN

Skoda Superb 08 >

Skoda Yeti 09 >

Smart Car > 2006

Remove the vehicle speedometer assembly. The CAN wires are located at the connection plugs.The CAN wiring can also be accessed in the loom towards the speedo, under the drivers dash area.

CAN HI = BROWN / REDCAN LO = WHITE / BLACK

Smart Fourtwo 2007>

Remove the vehicle audio unit. The CAN wires are located in the loom running.vertical towards the heater panel at the top of the dash. Also available at the OBD Socket.

CAN HI = GREEN / WHITE OR OBD Pin 6CAN LO = GREEN OR OBD Pin 14

CANM8 CANNECT Installation File>

SsangYong Actyon 2012>

The CAN wiring is located at the OBD socket, under the drivers side dash.The CAN bus wiring is a twisted pair of wires, detailed as below:

SsangYong Korando 2010>

SsangYong Kyron 2005 >

SsangYong Rodius 2005 - 2014

SsangYong Rodius 2014 >

SsangYong Turismo 2014 >

Subaru Forester 2009 >

Subaru Impreza 2008 >

Subaru Legacy 2004 >

Subaru Outback 2003 >

Subaru XV 2012 >

Suzuki Alto

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD socket, near the centre console under drivers side dash.

Unclip the socket for access.The CAN bus wiring is a twisted pair of wires, coloured as below:

Suzuki Grand Vitara

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD socket, near the centre console under drivers side dash.Unclip the socket for access. Alternatively, the CAN wiring is also located at the speedometermulti-plug, in pins 8 and 10. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = OBD Socket - Pin 6 OR RED wire at the speedometer multi-plug.CAN LO = OBD Socket - Pin 14 OR WHITE wire at the speedometer multi-plug.

Suzuki Splash

Suzuki Swift 2006 >

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD socket, near the centre console under drivers side dash.Unclip the socket for access. Alternatively, the CAN wiring is also located at the speedometermulti-plug, in pins 8 and 10. The CAN bus wiring is a twisted pair of wires, coloured as below:

Suzuki SX4

Tesla S

Unclip the under panel / pocket trim below the central display unit and locate the white connector.Identify the CAN Bus wirin detailed below:

CAN HI = Purple / WhiteCAN LO = Purple

Toyota Avensis (2009 >)

Toyota BB 2006 >

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD socket, near the centre console under drivers side dash.Unclip the socket for access. Alternatively, the CAN wiring is also located at the speedometer

multi-plug, in pins 39 and 40. The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = OBD Socket - Pin 6 OR BLACK wire at the speedometer multi-plug.CAN LO = OBD Socket - Pin 14 OR WHITE wire at the speedometer multi-plug.

Toyota Camry (2006 >)

Toyota Estima 2006 >

CAN HI = OBD Socket - Pin 6 OR BLACK wire at the speedometer multi-plug.CAN LO = OBD Socket - Pin 14 OR WHITE wire at the speedometer multi-plug.

Toyota GT86 : 2012 >

Toyota Hi-Lux : 2008 >

Vehicle CAN Bus LocationPlease note that only the PARK range of products are compatible with this vehicle model.

PLEASE NOTE THERE IS NO SPEED PULSE SUPPORT FOR THIS VEHICLE, ONLY PARK

Toyota iQ : 2009 >

Toyota Land Cruiser 2009 >

Toyota Prius : 2005 >

Toyota Prius : 2009 >

Toyota ProAce 2013 >

The CAN wires can be located at the OBD socket - lower drivers side dash.The CAN bus wiring is a twisted pair of wires detailed as below:

Toyota RAV 4 2006 >

CAN HI = OBD Socket - Pin 6 OR DARK GREEN wire at the speedometer multi-plug.CAN LO = OBD Socket - Pin 14 OR WHITE wire at the speedometer multi-plug.

Toyota Verso S (2011 >)

Toyota Yaris (2006 >)

Toyota Yaris (2011 >)

Vauxhall Agila 2009 >

CAN HI = OBD Pin 6 - Brown / BlackCAN LO = OBD Pin 14 - Brown

Vauxhall Ampera

Vauxhall Antara 2007 >

Vehicle CAN Bus LocationThe CAN wiring is located at the OBD socket, under the drivers side dash.

Unclip the socket for access. This vehicle uses 'Single Wire' CAN, connect as below:

Vauxhall Astra H 2005 - 2010

Vehicle CAN Bus LocationConnect at the OBD socket or at the radio Quadlock

The OBD socket is located in the lower, centre dash area.The CAN bus wiring is detailed below:

CAN HI = GREEN (PIN 1 at OBD - or GREEN (twisted pair) - Radio Quad lock)CAN LO = BROWN (PIN 4 at OBD - or WHITE (twisted pair) - Radio Quad lock)

Vauxhall Astra J 2009 - 2015

Vauxhall Astra K 2016 >

Vauxhall Cascada

Vauxhall Corsa / Combo >2012

Remove the vehicle speedometer assembly.The CAN bus wiring is a twisted pair of wires located at the multiplug, coloured as below:

Vauxhall Combo 2012 >

Vauxhall Corsa / Combo >2006

Vauxhall Corsa 2006 >

Vauxhall Insignia

Vauxhall Meriva 2004 >

Vauxhall Meriva 2010 >

CANM8- CANNECT Installation File

Vauxhall Mokka 2012 >

Vauxhall Movano > 2008

The CAN wiring is located at the OBD socket, behind the drivers side lower dash panel.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

Vauxhall Movano 2009 >

The CAN wiring is located at the OBD socket, inside the glove box.Unclip the socket for access. The CAN bus wiring is a twisted pair of wires, detailed as below:

Vauxhall Signum

Vauxhall Vectra

Vauxhall Vivaro

Vauxhall Zafira A > 2005

Remove the drivers side kick panel. The CAN wires are located inside a black plastic loom.

The CAN bus wiring is a STRAIGHT pair of wires, coloured as below:

CAN HI = GREEN CAN LO = WHITE

Vauxhall Zafira B 2005 >

Connect at the OBD Socket or at the radio wiring connector.OBD : Remove the ash tray and inner metal plate. Conect at the OBD socket loom.

CAN HI = GREEN (PIN 1 at OBD)CAN LO = BROWN (PIN 4 at OBD)

Vauxhall Zafira C 2012 >

Connect at the OBD Socket or at the radio wiring connector.OBD : Remove the ash tray and inner metal plate. Conect at the OBD socket loom.

VW Amarok

Remove the lower drivers side under panel. The CAN wires are a twisted pair located in the mainloom near the steering column. The CAN may also be available at the audio Quadlock connector.

CANM8CANNECT Installation File

VW Beetle

CAN HI = ORANGE / BLACKCAN LO = ORANGE / BROWN

VW Caddy 2004 - 2015

Remove the lower drivers side under panel. The CAN wires are located in the main wiring loom.The CAN bus wiring is a twisted pair of wires, coloured as below:

On later models, the CAN wiring may be located in the steering column loom.

VW Caddy 2016 >

On later models, the CAN wiring may be located in the steering column loom.

VW Crafter

Remove the drivers side lower dash panel.The CAN bus wiring is a twisted pair of wires coloured as below:

VW Eos : 2006 >

The CAN wiring can also be found in the harnesses to the front doors.

VW Fox

VW Golf V : 2004 >

VW Golf VI : 2009 >

The CAN wiring can also be found in the harnesses to the front doors.

VW Golf VII : 2012 >

CAN HI = ORANGE / GREEN - Also located at Pin 16 (BCM Brown plug - Rear of fuse box)CAN LO = ORANGE / BROWN - Also located at Pin 17 (BCM Brown plug - Rear of fuse box)

VW Golf Plus

VW Jetta 2005 >

Remove the lower drivers side under panel.The CAN bus wiring is a twisted pair of wires, coloured as below:

VW Passat 02 > 05

CAN HI = ORANGE / BLACKCAN LO = ORANGE / BROWN

VW Passat 05 >

Remove the lower drivers side under panel. The CAN wires are located at a 12 way multi-plug.The CAN bus wiring is a twisted pair of wires, coloured as below:

VW Passat : 2011 >

VW Polo 2005 - 2009

CAN HI = ORANGE / PURPLE or ORANGE / BLACK CAN LO = ORANGE / BROWN

VW Polo 2009 - 2014

VW Polo 2014 >

VW Routan

VW Scirocco

The CAN Bus wiring can be found at the steering column loom.

VW Sharan 2004 - 2010

Vehicle CAN Bus LocationThe CAN wires are located at the GREEN connector located at the rear of the speedometer. Remove the steering

column housing. There are 2 x Torx screws securing the speedometer. Remove these and insert a plastic lever tool at

the top edge of the speedometer glass. Lever the speedo forward to release. There are 2 sets of CAN wiring at the

connection plug - only one set carries the CAN data! The CAN wiring is a twisted pair coloured as below :-

Later models may also feature the CAN wiring at the radio (top ISO connector):-

VW Sharan 2010 >

The CAN Bus wiring is located at the steering column harness

VW Tiguan

VW Touareg : 2003 >

Remove the dash trim to gain access to the rear of the headlamp control switch.

The interface is installed to the CAN wiring in the wiring loom behind the switch.

VW Touareg : 2011 >

The interface is installed to the CAN wiring in the steering column loom.

VW Touran

VW Transporter 2003 >

Remove the lower drivers side under panel. The CAN wires are located at a 6 way Brown multi-plug.The CAN bus wiring is a twisted pair of wires, coloured as below:

CAN HI = ORANGE / GREEN (Under Dash)CAN LO = ORANGE / BROWN

VW Transporter 2010 >

Volvo C30

Volvo General J-1939

The CAN wires are located under the fuse box in a Green connector.The CAN bus wiring is a twisted pair of wires coloured as below:

CAN HI = YELLOWCAN LO = GREEN

Volvo S40 2005 >

Volvo S60

Locate the OBD socket, lower drivers side dash. The loom can be pulled down for wire access.

Volvo S80

Volvo V40 2012 >

Locate the OBD socket, lower drivers side dash. The loom can be pulled down for wire access.The CAN wiring is a twisted pair detailed as below:

Volvo V50 2005 >

Volvo V60 & XC60

Volvo V70 & XC70

Vehicle CAN Bus LocationLocate the OBD socket, lower drivers side dash. The loom can be pulled down for wire access.

If CAN wires are in positions 3 & 11, use option 1 - otherwise use option 2.

Pre 2004 models - OBD CAN may not be available. Connect behind the speedometer or radio.

Option 1: CAN HI = PIN 3 (White - also at speedo & radio) CAN LO = PIN 11 (Green - also at speedo & radio)

Volvo XC90

Yamaha FJR1300

Remove the screen and plastic cover in front of the speedometer to expose the wiring harness.Identify the CAN Bus wirin detailed below:

CAN HI = Blue / RedCAN LO = Blue / Black

CANM8 General Product Installation 025 - Carsec - … Cherokee 2010 Jeep Cherokee Jeep Renegade Jeep...

Documents