Post on 16-Mar-2020
transcript
SPECIALCOMMUNICATION
C A T A L O G U E 2 0 1 8 / 2
Special CommunicationAntennas and Solutions for Blue Light and Armed Forces
Who we are and what we stand forKathrein is a specialist for reliable, high-quality communication technologies.
The company is driving innovation and technology in today’s connected world. Its ability to provide solu-tions and services enables people all over the world to communicate, access information and use media, whether at home, at the office or on the road.
The business covers a broad spectrum: from mobile communication, RFID and special solutions, to satellite reception and broadcast technology, to transmission and reception systems in vehicles.
As a hidden champion and family-owned enterprise, Kathrein has been working on the technologies of tomorrow since 1919. The company takes pride in its dedicated employees and passion for customers and quality.
Our Solutions
Find out more about us at www.kathrein.com
MOBILE COMMUNICATION
BUSINESSSOLUTIONS SAT SPECIAL
COMMUNICATION BROADCAST AUTOMOTIVE
370–520 MHzDirectional AntennasOmni AntennasIndoor AntennasSpecial Purpose Antennas 37
0–52
0 M
Hz
700–850 MHzDirectional AntennasOmni AntennasIndoor Antennas
700–
850
MHz
2300–2600 MHzDirectional AntennasOmni AntennasIndoor Antennas
2300
–260
0 M
Hz
Accessories
Splitters and TappersDual-Band CombinersLow Noise Amplifier GPSMechanical AccessoriesKathrein’s Remote Electrical Tilt System (RET) Ac
cess
ories
4
5
Summary of Antenna Types, Antenna Line Products and AccessoriesThe articles are listed by type number in numerical order. New or changed product.
Type No. PageType No. PageType No. PageType No. Page
848...
848114 21
848657 24
849...
849203 42
852...
852626 12
852627 14
852628 15
852629 16
853...
853203V02 34
853266 25
893...
89321571 82 + 83
911210..
91121012 38 + 39
91121013 40 + 41
911213..
91121363 17
91121364 18
91121864 51
91121872 47
911219..
91121954 68
91121957 71
91121959 20
91121975 62 + 63
91121976 64 + 65
91121977 66 + 67
91121993 72
91131...
91131237 69
91131733 60 + 61
92210...
92210001 27
92210002 27
92210012 76 + 77
92210013 76 + 77
92210014 76 + 77
92210015 76
97121...
97121242 78
97121253 84
91121388 26
91121389 28
911214..
91121402 19
91121416V02 37
91121440 26
91121441 28
911215..
91121514 13
91121542 70
911217..
91121732V02 49
91121743 26
91121744 28
91121762 50
91121775 54 + 55
91121776V01 56 + 57
91121777V01 58 + 59
91121792 48
911218..
91121822 46
91121823 73
91121826 52 + 53
97131...
97131120 80
97131128 80
97131129 80
97131271 81
98121...
98121116 30
98121119 29
K74...
K7431348 79
K7431358 79
K81...
K813132 32
K8134321 31
K8134322 31
K86...
K862232 21
K862748 23
K863032 22
6
Antenna Designs:Antenna Families / RET-systemDistinguishing features
Design Compact size and elegant design are the distinguishing features of Kathrein’s antenna families.
Radome The radomes cover the internal antenna components. The fiberglass material guarantees optimum performance with regards to stability, strength, UV resis-tance, painting and weather protection. The colour of the radome of outdoor panel antennas is similar to RAL 7035.
Environmental influences Kathrein antenna designs are based on fundamental engineering knowledge and also on our decades of practical experience, during which the various constructions and materials used have proved their outstanding reliability.
Environmental conditions Kathrein cellular antennas are designed to operate under the environmental conditions as described in ETS 300 019-1-4 class 4.1 E.The antennas exceed this standard with regards to the following items:– Low temperature: –55 °C– High temperature (dry): +60 °C
Environmental tests Kathrein antennas are designed according to the specifications as defined in ETS 300 019-2-4. The homogenous design of Kathreins antenna families uses identical modules and materials. Extensive tests have been performed on typical samples and modules. The vibration test has been adapted relating to frequency and acceleration to the conditions of mast mounted antennas.
Impedance Standard Impedance for all products is 50 Ω unless otherwise stated.
Great variety of half-power beam width, gain values, electrical downtilt
According to the antenna type selected, customers can choose from different half-power beam widths, gain values and electrical downtilts for panel antennas. Downtilts are either fixed or adjustable and controlled by remote electrical tilt system (RET).
Low intermodulationproducts (typ. <–153 dBc)
With many years of experience in the construction of antennas and intensive research into the effects of intermodulation, we offer optimized material and technology used for antennas (the given value refers to 3rd order products measured with 2 carriers of 20 W each).
Excellent tracking Tracking states the symmetry between the +45° and –45° polarized horizontal pattern. Bad tracking values lead to interferences in the network and reduced diversity performance. Kathreins special Tracking compensa tion reduces the average value measured at ±60° to < 2–3 dB.
7
Antenna Designs:Antenna Families / RET-systemDistinguishing features
Multi-array design Besides standard single array antennas, Kathrein designs antennas providing multiple antenna arrays in one radome. These multi-array antennas do not only supply a future-proof multiplicity of diverse frequency bands for various technologies, but are also well-prepared for different MIMO-applications. The Kathrein portfolio contains a high variety of design solutions like interleaved and side-by-side antenna types or combinations of both as well as filter realizations.
Multi-functional installation hardware
Depending on the type, the antennas are equipped with up to 2 attachment points. Panels can be wall-mounted without any additional hardware. For mast-mounting, brackets and mechanical downtilt kits are available. To assist the installation technicians in aligning the panels, an azimuth adjustment tool can be supplied (see Mechanical Accessories).
MTBF Statement Traditionally, passive components like antennas cannot be well calculated due to the lack of a sufficient number of components in the MTBF library. Unfortunately, this constraint results in a very inaccurate calculation. Thus, such results are technically questionable and unrealistic.In essence, antennas are made out of mechnical parts that do not show any failure rates. Only available failure rates can be calculated into an MTBF value. Consequently such components cannot be listed in any MTBF library.
Remote Electrical Tilt System AISG Compliancy
Kathrein hereby states that RET devices, as far as the functionality and features are described within the AISG / 3GPP standard, are compliant with the standard.
NGMN-P-BASTA All antennas which are measured according to the specifications given in NGMN-P-BASTA White Paper Version 9.6 are clearly marked in the data sheet. Kathrein is changing over more and more data sheets to NGMN-P-BASTA. The latest data sheets can be found on our homepage.
RET RFID Functionality Kathrein‘s latest Remote Control Unit (RCU) is equipped with an internal RFID reader. Most of our antennas are equipped with RFID tags in their spindles. With this, all relevant antenna data can automatically be read out by the RCU.Further information as well as an up-to-date list of the antennas can be found on our homepage. The according data sheets are marked by an RFID sign.
4.3-10 Connectors Partly, Kathrein’s latest mobile communication antennas and antenna line products are equipped with 4.3-10 connectors.The advantages of this connector are:• Reduced dimensions on the bottom plate for more installation space• Improved PIM stability and performance• Easier installation, lower tightening torque
The universal 4.3-10 jack can be used with 3 different connector types (screw type, push-pull type and hand screw type).
8
Mechanical downtilt For further technical information please see “Mechanical Accessories”, page 85.
Electrical downtilt Description of the adjustment mechanism (protective cap removed):
Remote Electrical Tilt (RET) For further technical information please see “RET”, pages 88 and 89.Description of bottom end cap (exemplary picture):
Downtilting of Antennas with external RCU:Downtilt Possibilities
Manual adjustment procedure:
936.
4037
S
ubje
ct to
alte
ratio
n.
Page 2 of 2
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-973Internet: www.kathrein.de
General Instructions for Feederline Installationfor Dual-band Antennas
Please note: In order not to damage the interfaces, please make sure that only the right tools are used.Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrenchwidth.
Installation of the feederline connector and RCU (optional):In order to protect the adjustment mechanism the protective caps have to be attached during feederline installation!
Carefully place the connector and fix thenut using a torque-wrench (according tothe manufacturers guidelines).
After feederline installation the optionalremote control units (RCU) can bemounted.
For a full description of RCU installationplease refer to the respective data sheet.
Ventilation hole
Colour coding:Correlation of each RF input to:– the corresponding adjustment mechanism– the frequency range– the polarization
Adjustment mechanism(protective cap removed)
7-16 female (long neck)
Spindle with tilting scale
Description of bottom end cap (exemplary picture):
Remove the protective cap and the twist protection completely.
➀ Twist protection.➁ Downtilt spindle with
integrated scale.
➀ Thread for fixing the pro-tective cap or the RCU (Remote Control Unit).
➁ Gearwheel for RCU power drive.
To set the downtilt ang-le exactly, you must look horizontally at the scale. The lower edge of the gear wheel must be used for alignment.
Set downtilt angle by rotating the gearwheel.
Screw on the twist protection and the protective cap again.
0° – max.°
0° – max.°
1
2
2
1
9
Dimensions of Panels
Antenna dimensions and detailed connector position can be found on our current data sheets. Please refer to the information on our latest data sheets which are available on our homepage:
www.kathrein.comg Mobile Communication
An example is shown below of how the antenna dimensions are displayed on our data sheets:
1818
| 7
1.62)
1)
2056
| 8
0.9
1999
| 7
8.7
3)
1) 22 | 0.92) 150 | 5.93) ∅ 11 | 0.4 All dimensions in mm | inches
97
| 3.
8 14
0 |
5.5 2
29 |
9.0
*
131 | 5.2221 | 8.7311 | 12.2
164
| 6.
5 *
378 | 14.9 *
L 6
1695-2690
Y1 Y1L 5
1695-2690
L 2
698 - 862
R1
L 4
880 - 960
R2L 3
880 - 960
R2
L 1
698 - 862
R1R 8
1427-2690
Y2R 7
1427-2690
Y2
* Dimensions refer to radome
Bottom viewFront view
10
Kathrein AntennasProduct Description (Type)
6-Port Antenna LB/2HB 1.4m 65° | 698–960 14.5dBi | 2x1695–2690 18dBi
Numberof Ports
FrequencyRange(s)
Length
HorizontalHalf-power Beam Width(s)
Frequency Rangeand Gain Value
11
370–
520
MHz
Type Type No. Height[mm]
Input Page
Directional Antennas
2-Port Antenna 380–500 65° 12dBi 852626 992 2 x 7-16 female 12
2-Port Antenna 380–470 65° 14dBi 0°–14°T 91121514 1999 2 x 7-16 female 13
2-Port Antenna 380–500 65° 15dBi 852627 2000 2 x 7-16 female 14
2-Port Antenna 380–500 88° 10.5dBi 852628 1007 2 x 7-16 female 15
2-Port Antenna 380–500 88° 13.5dBi 852629 1997 2 x 7-16 female 16
1-Port Antenna 380–500 65° 12dBi 91121363 992 7-16 female 17
1-Port Antenna 380–500 65° 15dBi 91121364 2000 7-16 female 18
1-Port LogPer 380–520 87° 9dBi 91121402 785 7-16 female 19
4-Port Antenna 380–470698–791
88°65°
13dBi 2°T16dBi 2°T
91121959 2600 4 x 4.3-10 female 20
Omnidirectional Antennas
1-Port Omni 370–430 360° 2dBi 848114 555 N female 21
1-Port Omni 406–470 360° 2dBi K862232 515 N female 21
1-Port Omni 380–470 360° 4dBi K863032 315 N female 22
1-Port Omni 380–400 360° 7.5dBi K862748 2840 7-16 female 23
1-Port Omni 410–430 360° 8dBi 8.5°T 848657 3114 7-16 female 24
1-Port Omni 450–470 360° 8.5dBi 853266 3113 7-16 female 25
Indoor Omnidirectional Antennas
1-Port Omni 380–405 360° 2dBi 91121388 77 N female 26
1-Port Omni 405–430 360° 2dBi 91121440 77 N female 26
1-Port Omni 450–470 360° 2dBi 91121743 77 N female 26
1-Port Omni 380...6000 360° 1–6dBi 92210001 187 N female 27
1-Port Omni 380...6000 360° 1–6dBi 92210002 187 4.3-10 female 27
Indoor Directional Antennas – Single-band
1-Port Indoor 380–405 90° 7dBi 91121389 302 N female 28
1-Port Indoor 405–430 90° 7dBi 91121441 302 N female 28
1-Port Indoor 440–470 90° 7dBi 91121744 302 N female 28
Special Purpose Antennas
Special Purpose Antenna 380–430 98121119 150 N female 29
Special Purpose Antenna 380–430 GPS 1575 98121116 150 N female 30
Special Purpose Antenna 406–428 K8134321 70 M 11 x 1 female 31
Special Purpose Antenna 406–428 K8134322 70 N female 31
Special Purpose Antenna 410–470 K813132 142 N female 32
New or changed product
Summary – Antennas 370...6000 MHz
12 For more information about additional mounting accessories please refer to page 85
PanelDual PolarizationHalf-power Beam Width
380–500X
65°
2-Port Antenna 380–500 1.0m 65° 12dBi
Type No. 852626Frequency range 380 – 430 MHz 430 – 500 MHzPolarization +45°, –45° +45°, –45°Gain 11.5 dBi 12 dBiHalf-power beam widthCopolar +45°/–45°
Horizontal: 68°Vertical: 37°
Horizontal: 65°Vertical: 32°
Front-to-back ratio > 25 dBIsolation > 30 dBImpedance 50 ΩVSWR < 1.5Intermodulation IM3 < −150 dBc ( 2 x 43 dBm carrier)Max. power per input 500 W (at 50 °C ambient temperature)
Material: Radiator: Tin-plated copper. Reflector screen: Weather-proof aluminum.Radome: Fiberglass, colour: Grey.All screws and nuts: Stainless steel.
Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.
Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
380–500
Mechanical specifications
Input 2 x 7-16 femaleConnector position RearsideWind load Frontal: 500 N (at 150 km/h)
Lateral: 220 N (at 150 km/h)Rearside: 715 N (at 150 km/h)
Max. wind velocity 200 km/hHeight/width/depth 992 / 492 / 190 mmCategory ofmounting hardware M (Medium)
Weight 12 kgPacking size 1140 x 523 x 252 mm
380 – 430 MHz: +45°/–45° Polarization
430 – 500 MHz: +45°/–45° Polarization
10
3
0
68°136°
Bd 3 dB
0
37°
10
10
3
0
65°122°
Bd 3 dB
0
32°
10
Horizontal Pattern
Horizontal Pattern
Vertical Pattern
Vertical Pattern
380–500–45°
380–500+45°
7-16 7-16
13For more information about additional mounting accessories please refer to page 85
370–
520
MHz
Mechanical specifications
Input 2 x 7-16 femaleConnector position BottomAdjustmentmechanism
1 x, Position bottomcontinuously adjustable
Wind load Frontal: 1160 N (at 150 km/h)Lateral: 480 N (at 150 km/h)Rearside: 1870 N (at 150 km/h)
Max. wind velocity 200 km/hHeight/width/depth 1999 / 575 / 199 mmCategory ofmounting hardware H (Heavy)
Weight 22 kgPacking size 2250 x 640 x 225 mm
PanelDual PolarizationHalf-power Beam WidthAdjust. Electrical Downtiltset by hand or by optional RCU (Remote Control Unit)
380–470X
65°
Horizontal Pattern
Horizontal Pattern
Vertical Pattern0° – 14° electrical downtilt
Vertical Pattern0° – 14° electrical downtilt
2-Port Antenna 380–470 2.0m 65° 14dBi 0°–14°T
Type No. 91121514Frequency range
380 – 430 MHz 430 – 470 MHzPolarization +45°, –45° +45°, –45°Gain (dBi)Tilt
13.5 ... 13 ... 12.50° ... 7° ... 14°
14 ... 13.5 ... 130° ... 7° ... 14°
Horizontal Pattern:Half-power beam width 66° 62°Front-to-back ratio, copolar(180° ±30°)
> 25 dB
Cross polar ratio 0°Maindirection ±60°
Typically: 25 dB> 10 dB
Vertical Pattern:Half-power beam width 22° 19°Electrical tilt 0° – 14°, continuously adjustable
Isolation > 30 dBImpedance 50 ΩVSWR < 1.5Intermodulation IM3 < −150 dBc (2 x 43 dBm carrier)Max. power per input 400 W (at 50 °C ambient temperature)
Material: Radiator: Tin-plated copper. Reflector screen: Weather-proof aluminum.Radome: Fiberglass, colour: Grey.All screws and nuts: Stainless steel.
Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.
Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
430 – 470 MHz: +45°/–45° Polarization
380 – 430 MHz: +45°/–45° Polarization
380–470
0°–14°
62°115°
dB
10
3
0
10
3
0
19°
dB
122°
dB
10
3
0
66°
3
0
10
dB
22°
380–470–45°
380–470+45°
7-16 7-16
14 For more information about additional mounting accessories please refer to page 85
PanelDual PolarizationHalf-power Beam Width
380–500X
65°
2-Port Antenna 380–500 2.0m 65° 15dBi
Type No. 852627Frequency range 380 – 430 MHz 430 – 500 MHzPolarization +45°, –45° +45°, –45°Gain 14.5 dBi 15 dBiHalf-power beam widthCopolar +45°/–45°
Horizontal: 65°Vertical: 18°
Front-to-back ratio > 25 dBIsolation > 30 dBImpedance 50 ΩVSWR < 1.5Intermodulation IM3 < −150 dBc ( 2 x 43 dBm carrier)Max. power per input 500 W (at 50 °C ambient temperature)
Material: Radiator: Tin-plated copper. Reflector screen: Weather-proof aluminum.Radome: Fiberglass, colour: Grey.All screws and nuts: Stainless steel.
Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.
Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
380–500
Mechanical specifications
Input 2 x 7-16 femaleConnector position RearsideWind load Frontal: 1100 N (at 150 km/h)
Lateral: 440 N (at 150 km/h)Rearside: 1540 N (at 150 km/h)
Max. wind velocity 200 km/hHeight/width/depth 2000 / 492 / 190 mmCategory ofmounting hardware H (Heavy)
Weight 19 kgPacking size 2080 x 523 x 252 mm
+45°/–45° Polarization
10
3
0
65°120°
Bd
10
3
0
18°
Bd
Horizontal Pattern Vertical Pattern
380–500–45°
380–500+45°
7-16 7-16
15
370–
520
MHz
For more information about additional mounting accessories please refer to page 85
PanelDual PolarizationHalf-power Beam Width
380–500X
88°
2-Port Antenna 380–500 1.0m 88° 10.5dBi
Type No. 852628Frequency range 380 – 430 MHz 430 – 500 MHzPolarization +45°, –45° +45°, –45°Gain 2 x 10 dBi 2 x 10.5 dBiHalf-power beam widthCopolar +45°/–45°
Horizontal: 88°Vertical: 40°
Horizontal: 86°Vertical: 35°
Front-to-back ratio, copolar > 20 dB > 20 dBIsolation > 30 dB > 30 dBImpedance 50 Ω 50 ΩVSWR < 1.5 < 1.5Intermodulation IM3 < −150 dBc ( 2 x 43 dBm carrier)Max. power per input 500 W (at 50 °C ambient temperature)
Material: Reflector screen: Weather-proof aluminum.Radome: Fiberglass, colour: Grey.All screws and nuts: Stainless steel.
Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.
Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
380–500
Mechanical specifications
Input 2 x 7-16 femaleConnector position BottomWind load Frontal: 420 N (at 150 km/h)
Lateral: 220 N (at 150 km/h)Rearside: 540 N (at 150 km/h)
Max. wind velocity 200 km/hHeight/width/depth 1007 / 317 / 193 mmCategory ofmounting hardware M (Medium)
Weight 10.5 kgPacking size 1140 x 330 x 240 mm
380–500–45°
380–500+45°
7-16 7-16
430 – 500 MHz: +45°/–45° Polarization
380 – 430 MHz: +45°/–45° Polarization
3 dB
10
0
86°
165°
3
0
10
Bd
35°
3 dB
10
0
88°
165°
3
0
10
Bd
40°
Horizontal Pattern
Horizontal Pattern
Vertical Pattern
Vertical Pattern
16 For more information about additional mounting accessories please refer to page 85
PanelDual PolarizationHalf-power Beam Width
380–500X
88°
2-Port Antenna 380–500 2.0m 88° 13.5dBi
Type No. 852629Frequency range 380 – 430 MHz 430 – 500 MHzPolarization +45°, –45° +45°, –45°Gain 2 x 13 dBi 2 x 13.5 dBiHalf-power beam widthCopolar +45°/–45°
Horizontal: 88°Vertical: 20°
Horizontal: 86°Vertical: 17°
Front-to-back ratio, copolar > 20 dB > 20 dBIsolation > 30 dB > 30 dBImpedance 50 Ω 50 ΩVSWR < 1.5 < 1.5Intermodulation IM3 < −150 dBc ( 2 x 43 dBm carrier)Max. power per input 500 W (at 50 °C ambient temperature)
Material: Reflector screen: Weather-proof aluminum.Radome: Fiberglass, colour: Grey.All screws and nuts: Stainless steel.
Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.
Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
380–500
Mechanical specifications
Input 2 x 7-16 femaleConnector position BottomWind load Frontal: 890 N (at 150 km/h)
Lateral: 480 N (at 150 km/h)Rearside: 1150 N (at 150 km/h)
Max. wind velocity 200 km/hHeight/width/depth 1997 / 317 / 193 mmCategory ofmounting hardware H (Heavy)
Weight 18.5 kgPacking size 2130 x 330 x 240 mm
380–500–45°
380–500+45°
7-16 7-16
430 – 500 MHz: +45°/–45° Polarization
380 – 430 MHz: +45°/–45° Polarization
3 dB
10
0
86°
165°
3
0
10
Bd
17°
3 dB
10
0
88°
165°
3
0
10
Bd
20°
Horizontal Pattern
Horizontal Pattern
Vertical Pattern
Vertical Pattern
17
370–
520
MHz
For more information about additional mounting accessories please refer to page 85
Multi-band PanelVertical PolarizationHalf-power Beam Width
380–500V
65°
1-Port Antenna 380–500 1.0m 65° 12dBi
Type No. 91121363Frequency range 380 – 430 MHz 430 – 500 MHzPolarization Vertical VerticalGain 11.5 dBi 12 dBiHalf-power beam widthCopolar +45°/–45°
Horizontal: 68°Vertical: 37°
Horizontal: 63°Vertical: 32°
Front-to-back ratio > 18 dB > 20 dBImpedance 50 ΩVSWR < 1.5Intermodulation IM3 < −150 dBc ( 2 x 43 dBm carrier)Max. power per input 500 W (at 50 °C ambient temperature)
Material: Reflector screen: Weather-proof aluminum. Radiator: Tin-plated copper.Radome: Fiberglass, colour: Grey.All screws and nuts: Stainless steel.
Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.
Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
380–500
Mechanical specifications
Input 1 x 7-16 femaleConnector position RearsideWind load Frontal: 500 N (at 150 km/h)
Lateral: 220 N (at 150 km/h)Rearside: 715 N (at 150 km/h)
Max. wind velocity 200 km/hHeight/width/depth 992 / 492 / 190 mmCategory ofmounting hardware M (Medium)
Weight 12 kgPacking size 1140 x 523 x 252 mm
380 – 430 MHz
10
3
0
68°136°
Bd 3 dB
0
37°
10
10
3
0
63°122°
Bd 3 dB
0
32°
10
Horizontal Pattern
Horizontal Pattern
Vertical Pattern
Vertical Pattern
18 For more information about additional mounting accessories please refer to page 85
Multi-band PanelVertical PolarizationHalf-power Beam Width
380–500V
65°
1-Port Antenna 380–500 2.0m 65° 15dBi
Type No. 91121364Frequency range 380 – 430 MHz 430 – 500 MHzPolarization Vertical VerticalGain 14.5 dBi 15 dBiHalf-power beam widthCopolar +45°/–45°
Horizontal: 68°Vertical: 18°
Horizontal: 63°Vertical: 16°
Front-to-back ratio > 20 dBImpedance 50 ΩVSWR < 1.5Intermodulation IM3 < −150 dBc ( 2 x 43 dBm carrier)Max. power per input 500 W (at 50 °C ambient temperature)
Material: Reflector screen: Weather-proof aluminum. Radiator: Tin-plated copper.Radome: Fiberglass, colour: Grey.All screws and nuts: Stainless steel.
Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.
Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded.
380–500
Mechanical specifications
Input 1 x 7-16 femaleConnector position RearsideWind load Frontal: 1100 N (at 150 km/h)
Lateral: 440 N (at 150 km/h)Rearside: 1540 N (at 150 km/h)
Max. wind velocity 200 km/hHeight/width/depth 2000 / 492 / 190 mmCategory ofmounting hardware H (Heavy)
Weight 20 kgPacking size 2080 x 523 x 252 mm
380 – 430 MHz
430 – 500 MHz
10
3
0
68°136°
Bd
10
3
0
18°
Bd
10
3
0
63°122°
Bd
10
3
0
16°
Bd
Horizontal Pattern
Horizontal Pattern
Vertical Pattern
Vertical Pattern
19
370–
520
MHz
For more information about additional mounting accessories please refer to page 85
Logarithmic-periodicVertical PolarizationHalf-power Beam Width
380–520V
87°
1-Port LogPer Antenna 380–520 0.8m 87° 9dBi
Type No. 91121402Frequency range 380 – 410 MHz 410 – 470 MHz 470 – 520 MHzPolarization VerticalGain 9.2 dBi 9 dBi 8.7 dBiHalf-power beam width Horizontal: 80°
Vertical: 61°Horizontal: 85°Vertical: 60°
Horizontal: 88°Vertical: 59°
Impedance 50 ΩVSWR < 1.5Intermodulation IM3 < −150 dBc ( 2 x 43 dBm carrier)Max. power per input 500 W (at 50 °C ambient temperature)
Scope of supply: Antenna with weather protective casing for straight connectors.
Material: Radiator: Weather resistant aluminium.Radome: Fiberglass, colour: White.All screws and nuts: Stainless steel.
Attachment: To tubular masts of 50–380 mm diameter depending on the separate available clamps.
Ice protection: Due to the very sturdy antenna construction and the protection of the radiating system by the radome, the antenna remains operational even under icy conditions.
Grounding: All metal parts of the antenna including the mounting kit and the inner conductor are DC grounded.
Mechanical specifications
Input 7-16 femaleConnector position Rearside, pointing downwardsWind load Frontal: 54 N (at 150 km/h)
Lateral: 150 N (at 150 km/h)Max. wind velocity 180 km/hHeight/width/depth 785 / 400 / 400 mmWeight 6 kgPacking size 915 x 485 x 485 mm
380 – 410 MHz
410 – 470 MHz
470 – 520 MHz
3 dB
10
0
80°
139°108° 61°
3 dB
10
0
85°
145°
3 dB
10
0
88°
148°
10
3
0
60°107°
Bd
107° 59°
Horizontal Pattern
Horizontal Pattern
Horizontal Pattern
Vertical Pattern
Vertical Pattern
Vertical Pattern
20 For more information about additional mounting accessories please refer to page 85
PanelDual PolarizationHPBWFixed Electrical DT
698–791380–470XX
65°2°
88°2°
4.3-10 4.3-10
380–470–45°
380–470+45°
698–791–45°
698–791+45°
4.3-10 4.3-10
380 – 470 MHz: +45°/–45° Polarization
698 – 791 MHz: +45°/–45° Polarization
10
3
0
67°125°
dB
3 dB
10
0
88°
165°
8°
Bd
10
3
0
10
3
0
14°
Bd
Horizontal Pattern
Horizontal Pattern
Vertical Pattern
Vertical Pattern
Type No. 91121959Frequency range 380-470 MHz 698-791 MHz
Polarization +45° , -45° +45° , -45°Antenna Gain 2x 13 dBi 2 x 16 dBiHorizontal Pattern:Half-pow er beam w idth 88° 65°Front-to-back ratio Copolar: > 20dB Copolar: > 20dBVertical Pattern:Half-pow er beam w idth 14° 8°Electrical tilt 2°, f ixed 2°, f ixed
XXPol Panel 380-470/698-791 88°/65° 13dBi/16dBi 2°/2°
Impedance 50 50VSWR < 1.5 < 1.5Isolation: Intrasystem > 25dB > 25 dBIsolation: Intersystem > 25dBIntermodulation IM3 (2 x 43 dBm carrier)
< -150 dBc < -150 dBc
Max. pow er per input 250 W * 250 W ** (at 50°C ambient temperature)
2°2°
Dual-band PanelDual PolarizationHalf-power Beam WidthFixed Electrical Downtilt
Mechanical specifications
Input 4 x 4.3-10 femaleConnector position BacksideWind load Frontal: 480 N (at 150 km/h)
Lateral: 190 N (at 150 km/h)Rearside: 480 N (at 150 km/h)
Max. w ind velocity 200 km/hHeight/w idth/depth 2600 / 317 / 193 mmCategory of mounting hardw are
H (Heavy)
Weight 26 kgPacking size 2733 x 330 x 240 mmScope of supply Panel and 2 units of clamps
for 50 – 115 mm diameter
88° 65°
380 – 470 MHz: +45°/-45° Polarization
698 – 791 MHz: +45°/-45° Polarization
Preliminary Issue
380–470 698–791X X
4.3-10 4.3-10 4.3-10 4.3-10
90021959 Page 1 of 2
14°
8°
380-470-45°
380-470+45°
698-791-45°
698-791+45°
Special Communications
Mechanical specifications
Input 4 x 4.3-10 femaleConnector Position BacksideWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 480 | 108Lateral: 190 | 43Rearside: 480 | 108
Max. Wind Velocity km/hmph
200124
Height / Width / Depth mminches
2600 / 317 / 193102.4 / 12.5 / 7.6
Category of Mounting Hardware H (Heavy)
Weight kglb
26.0 / 28.2 (clamps incl.)57.3 / 62.3 (clamps incl.)
Packing Size mminches
2733 / 330 / 240107.6 / 13.0 / 9.5
Scope of Supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
4-Port Antenna 380–470/698–791 2.6m 88°/65° 13/16dBi 2°/2°T
Type No. 91121959380–470 698–791
Frequency range 380 – 470 MHz 698 – 791 MHzPolarization +45°, –45° +45°, –45°Gain 2 x 13 dBi 2 x 16 dBiHorizontal Pattern:Half-power beam width 88° 65°Front-to-back ratio, copolar > 20 dB > 20 dBVertical Pattern:Half-power beam width 14° 8°Electrical tilt 2°, fixed 2°, fixed
Impedance 50 Ω 50 ΩVSWR < 1.5 < 1.5Isolation: Intrasystem > 25 dB > 25 dBIsolation: Intersystem > 25 dBIntermodulation IM3(2 x 43 dBm carrier)
< −150 dBc < −150 dBc
Max. power per input 250 W* 250 W** (at 50 °C ambient temperature)
Preliminary Issue
21
370–
520
MHz
On the tip of atubular mast
Laterally at the tip of a tubular mast
3 dB
10
0
78°
Vertical Pattern
Hei
ght
Omnidirectional AntennasVertical Polarization
370...470V
Mechanicalspecifications 848114 K862232
Input N femaleConnector position BottomWind load(at 150 km/h)
Nlbf
204
Max. wind velocity
km/hmph
200124
Radome diameter
mminches
212.0
Weight kglb
1.02.2
0.81.7
Height mminches
55521.9
51520.3
Packing size mminches
112 x 97 x 6544.4 x 3.8 x 25.7
112 x 97 x 6144.4 x 3.8 x 24.2
848114: 1-Port Omni Antenna 370–430 0.5m 360° 2dBiK862232: 1-Port Omni Antenna 406–470 0.5m 360° 2dBi
Type No. 848114 K862232Frequency range 370 – 430 MHz 406 – 470 MHzPolarization VerticalGain 2 dBiImpedance 50 ΩVSWR 370 – 380 MHz: < 1.6
380 – 430 MHz: < 1.5< 1.5
Intermodulation IM3 < −150 dBc ( 2 x 37 dBm carrier)Max. power 100 W (at 50 °C ambient temperature)
Material: Radiator: Brass.Radome: Fiberglass, dia. 21 mm, colour: Grey.Base: Aluminum.Mounting U-bolt and all screws and nuts: Stain-less steel.
Mounting: The antenna can be attached in two ways with the supplied mounting kit:1. On the tip of a tubular mast of 40–54 mm
diameter (connecting cable runs inside the mast).
2. Laterally at the tip of a tubular mast of 20–54 mm diameter (connecting cable runs outside the mast).
Grounding: All metal parts of the antenna including the mounting kit are DC grounded.
22
Mechanical specifications
Input N femaleWind load(at 150 km/h)
Nlbf
409
Max. windvelocity
km/hmph
200124
Length mminches
31512.4
Weight kglb
1.63.5
Packing size mminches
880 x 330 x 10034.6 x 13.0 x 3.9
Half-wave Dipole Side-mountedVertical Polarization
1-Port Omni Antenna VPol 380–470 360° 4dBi
Type No. K863032Frequency range MHz 380 – 470Polarization VerticalGain dBi 4Impedance Ω 50VSWR 400 – 470 MHz: < 1.5
380 – 400 MHz: < 1.5; A = λ/4380 – 400 MHz: < 2.0; A > λ/4
Max. power per input W 450 (at 50 °C ambient temperature)
Material: Radiator: Hot-dip galvanized steel.Horizontal support pipe: Stainless steel.Mount: Aluminum. Tightening band and all screws and nuts: Stainless steel.Feedpoint radome: Fiberglass.
Attachment: To tubular masts of 60–320 mm | 2.4–12.6 inches diameter using supplied stainless steel tightening band (20 mm wide, 0.8 mm gauge) | (0.8 inches wide, 0.03 inches gauge).
Special features: The distance from tubular mast to radiator is adjustable from 170–580 mm | 6.7–22.8 inches.
Grounding: All metal parts of the antenna including the inner conductor and the supplied mount are DC grounded.
Horizontal radiation pattern: Depending on the distance A (edge of pipe mast to dipole) – see sketch.
380–470V
n Omnidirectional antenna with variable antenna-to-mast distance.
n Depending on the distance of the radiator from the mast edge and also on the mast diameter, various radiation patterns can be achieved.
Distance A
314
| 12.
4
580 | 22.8
M = 15 Nm
All dimensions in mm | inches
23
370–
520
MHz
Side-mounting brackets see page 86 + 87
1-Port Omni Antenna 380–400 2.8m 360° 7.5dBi
Type No. K862748Frequency range 380 – 400 MHzPolarization VerticalGain 7.5 dBiImpedance 50 ΩVSWR < 1.5Intermodulation IM3 < −150 dBc ( 2 x 43 dBm carrier)Max. power per input 500 W (at 50 °C ambient temperature)
Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey.Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel.
Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50–94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast).
Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled.
Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the require-ments of lightning protection class II. Grounding cross-section: 22 mm2 copper.
Omnidirectional AntennaVertical Polarization
380–400V
1 50
230
104
maximum
mast top
Bd
17°
10
3
0
Vertical Pattern
2840
mm
Mechanical specifications
Input 7-16 femaleConnector position BottomWind load 200 N (at 150 km/h)Max. wind velocity 200 km/hHeight 2840 mmRadome diameter 51 mmWeight 8.0 kgPacking size 3316 x 148 x 112 mm
24 Side-mounting brackets see page 86 + 87
Omnidirectional AntennaVertical PolarizationFixed Electrical Downtilt 8.5°
1-Port Omni Antenna 410–430 3.0m 360° 8dBi 8.5°T
Type No. 848657Frequency range 410 – 430 MHzPolarization VerticalGain 8 dBiElectrical tilt 8.5°, fixedImpedance 50 ΩVSWR < 1.5Intermodulation IM3 < −150 dBc ( 2 x 43 dBm carrier)Max. power per input 500 W (at 50 °C ambient temperature)
Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey.Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel.
Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50–94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast).
Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled.
Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the require-ments of lightning protection class II. Grounding cross-section: 22 mm2 copper.
Vertical Pattern8.5° electrical downtilt
Mechanical specifications
Input 7-16 femaleConnector position BottomWind load 220 N (at 150 km/h)Max. wind velocity 180 km/hHeight 3114 mmRadome diameter 51 mmWeight 8.0 kgPacking size 3376 x 196 x 102 mm
410–430V
1 50
230
104
maximum
mast top
3 dB
10
0
14°
3114
mm
25
370–
520
MHz
Side-mounting brackets see page 86 + 87
1-Port Omni Antenna 450–470 3.0m 360° 8.5dBi
Type No. 853266Frequency range 450 – 470 MHzPolarization VerticalGain 8.5 dBiImpedance 50 ΩVSWR < 1.5Intermodulation IM3 < −150 dBc ( 2 x 43 dBm carrier)Max. power per input 500 W (at 50 °C ambient temperature)
Material: Radiator: Copper and brass. Radome: Fiberglass, colour: Grey.Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel.
Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50–94 mm diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast).
Anti-static protection: All metal parts of the antenna as well as the supplied clamp attachment are grounded. The inner conductor is capacitively coupled.
Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the require-ments of lightning protection class II. Grounding cross-section: 22 mm2 copper.
Omnidirectional AntennaVertical Polarization
450–470V
1 50
230
104
maximum
mast top
3 dB
10
0
12°
Vertical Pattern
3113
mm
Mechanical specifications
Input 7-16 femaleConnector position BottomWind load 220 N (at 150 km/h)Max. wind velocity 180 km/hHeight 3113 mmRadome diameter 51 mmWeight 8.0 kgPacking size 3379 x 206 x 152 mm
26
91121388: 1-Port Indoor Antenna 380–405 360° 2dBi91121440: 1-Port Indoor Antenna 405–430 360° 2dBi91121743: 1-Port Indoor Antenna 450–470 360° 2dBi
Type No. 91121388 91121440 91121743Frequency range 380 – 405 MHz 405 – 430 MHz 450 – 470 MHzPolarization Vertical Vertical VerticalGain Approx. 2 dBi Approx. 2 dBi Approx. 2 dBiImpedance 50 Ω 50 Ω 50 ΩVSWR < 2.0 < 2.0 < 2.0Max. power 50 W (at 50 °C ambient temperature)Input 1 x N femaleProtection class IP 30Weight 429 gPacking size 267 x 267 x 114 mmDiameter 258 mmHeight 77 mm (without connector)
Material: Reflector: Aluminium.Radome: High impact polystyrol, colour: White.Additional painting is possible.
Mounting: Three holes in the base enable a mounting on the ceiling. Two types of screws are supplied. For the N connector a hole in the ceiling with a diameter of 35 mm is required.
Grounding: All metal parts including the inner conductor are DC grounded.
Available accessories: Power splitters (380–512 MHz)
Indoor Omnidirectional AntennasVertical Polarization
380...470V
1.6
mm
15.3 mm
N connector, female
160
mm
dia
met
er
3 ho
les
5 m
m d
iam
eter
min. dia. 35 mm
Press radome against installed reflector.
min. dia. 35 mm min. dia. 35 mm
Rotate radome until it locks in place.
min. dia. 35 mm min. dia. 35 mm
Pull downwards to remove radome.
min. dia. 35 mm321
• The antennas need no additional groundplane.
27
370–
520
MHz
1-Port Indoor 380...6000 360° 1–6dBi
Type No. 92210001 / 92210002Frequency range MHz 380–806 806–960 1395–1432
1710–21702300–2500 3300–3700 4900–6000
Polarization Linear, VerticalGain (typ.) dBi 1 (2*) 4 5 5 5 6Impedance Ω 50VSWR (max.) 3:1 (2.5:1*) 2:1 2:1 2:1 1.9:1 1.9:1Intermodulation IM3 dBc < −155 (2 x 20 dBm carrier)Max. power W 50 (at 50 °C ambient temperature)Flammability UL94Weight g 550Diameter mm 275Height mm 187 (without connector)Input 92210001: N female
92210002: 4.3-10 female* Specifications for ground plate of 40 cm and up, above a metal surface, with a spacing of 35–45 mm.
Material: Back plane: Aluminum; protected through chemical passivation.Radome: UV protected polycarbonate.
Mounting: Ceiling mounting.
Grounding: All metal parts including the inner conductor are DC grounded.
∅ 274.1
189.
8
15.4
Connector
PATENT PENDING PLATE
DANGEROUS PLATE
∅ 200.0
3 x ∅ 3.2
Connector
1-Port IndoorOmni AntennaVertical Polarization
380...6000
V
• The Multi-band Omni Antenna covers all the bands of Tetra, 2G and 3G cellular, as well as Wi-Fi and LTE.
• The antenna is aesthetic and has unobtrusive profile that blends easily with any environment.
• The antenna is easy-installed and is highly recommended as an outstandig logistic solution for in-bulding installations.
• The antenna is PIM certified, thus making it suitable for all multi-carrier systems.
28
Indoor Directional AntennasVertical PolarizationHalf-power Beam Width
380...470V
90°
91121389: 1-Port Indoor Antenna 380–405 90° 7dBi91121441: 1-Port Indoor Antenna 405–430 90° 7dBi91121744: 1-Port Indoor Antenna 450–470 90° 7dBi
Type No. 91121389 91121441 91121744Frequency range 380 – 405 MHz 405 – 430 MHz 450 – 470 MHzPolarization Vertical Vertical VerticalGain Approx. 7 dBi Approx. 7 dBi Approx. 7 dBiHalf-power beam width Horizontal: Approx. 90° Horizontal: Approx. 90° Horizontal: Approx. 90°Impedance 50 Ω 50 Ω 50 ΩVSWR < 2.0 < 2.0 < 2.0Max. power 50 W (at 50 °C ambient temperature)Input N female connectorProtection class IP 30Weight 1390 gPacking size 315 x 252 x 62 mmHeight/width/depth 302 x 243 x 50 mm
Material: Reflector: Copper.Radome: High impact polystyrol, colour: White.Additional painting is possible.Mounting plates: Stainless steel.
Mounting: Two holes of 6 mm diameter in the mounting plate. Screws are not supplied.
Grounding: All metal parts including the inner conductor are DC grounded.
Available accessories: Power splitters (380–512 MHz)
3 dB
10
0
90°
Horizontal Pattern
Pull the antenna down to the stop.
Mount the attachment plate to the wall using two screws of 4 mm diameter in the position as indicated.
Align the antenna over the attachment plate.
Mounting:
29
370–
520
MHz
Special Purpose Antenna380–430 MHz98121119• Low profile antenna in fiberglass radome.• The antenna fulfils the requirements according to EN 50155.
Type No. 98121119
AntennaInput N femaleFrequency range MHz 380 – 430VSWR < 1.7Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 100 (at 50° C ambient temperature)Inner conductor DC groundedRadome weight g | lb 186 | 0.4Total weight g | lb Approx. 500 | 1.1Packing size, L x W x H
mminches
150 x 90 x 1905.9 x 3.5 x 7.5
Height mminches
1505.9
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 1000 x 1000 mm | 39.4 x 39.4 inches using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
contact area
contact area
seal
Input Antenna 400 MHz
82
5685
145 11
543
142
11 m
m d
iam
eter
32
Mounting flange:
Situation of mounting
Mounting hole for the connector: 33 (max. 35) mm | 1.3 (max. 1.4) inches diameter.Note: Keep mounting surface clear of paint for electrical contact.Evenness of opposite surface 0.2 mm | 0.008 inches.Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nutM10 DIN 1587torque15 Nm – 20 NmAdded sealing
washer
51
Hex-head screw M10torque15 Nm – 20 Nm
15 |
0.6
All dimensions in mm | inches
30
Special Purpose Antenna380–430 MHz and GPS 1575 MHz98121116• Two-band antenna: 380–430 MHz and GPS.• The antenna can be operated in both frequency ranges
simultaneously.•Low profile antenna in fiberglass radome.• The antenna fulfils the requirements according to EN 50155.
Type No. 98121116
Antenna 380 – 430 MHzInput N femaleFrequency range 380 – 430 MHzVSWR < 1.7Gain 0 dB (ref. to the quarter-wave antenna)Impedance 50 ΩPolarization VerticalMax. power 100 W (at 50° C ambient temperature)Inner conductor DC groundedAntenna GPSInput Cable RG 316/U of 225 mm length
with TNC male connectorFrequency range 1575.42 ±1 MHzVSWR < 1.5Polarization Right hand circularGain (90° elevation) 2 dB (ref. to the circularly polarized
isotropic antenna)Impedance 50 ΩInner conductor DC groundedRadome weight 186 gTotal weight Approx. 500 gPacking size 150 x 90 x 190 mmHeight 150 mm
Material: Radiator: Copper and brass.Flange: Aluminum. Radome: Fiberglass.All screws and nuts: Stainless steel.Colour: Grey.Sealing: Neoprene and silicon. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 1000 x 1000 mm using 4 M10 bolts.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute and approved by the “Deutsche Bahn AG”, is DC grounded to protect against lightning and high-tension lines.
Accessories: Low noise amplifier GPS 86010142 (please order separately).
Warning: If the antenna is operated without the pre- amplifier type no. 86010142, please note the following points.– Due to the fact that the inner conductor of the
antenna GPS is DC grounded, the input of the GPS receiver is loaded with a DC short circuit. If the GPS receiver provides a remote DC power supply, this could damage the GPS receiver.
– At the input of the antenna GPS a level of –25 dB below the signal applied at the input of the antenna 380–430 MHz appears. Depending on the level of the signal applied at the input of the antenna 380–430 MHz, the GPS receiver may be overloaded or damaged.
contact area
contact area
seal
Input Antenna 400 MHz
82
5685
145 11
543
142
11 m
m d
iam
eter
32
Input AntennaGPS
Mounting hole for the connector: 33 (max. 35) mm diameter.Note: Keep mounting surface clear of paint for electri-cal contact.Evenness of opposite surface 0.2 mm.Use a cap nut or hex-head screw plus the enclosed sealing washer.
Cap nutM10 DIN 1587torque15 Nm – 20 NmAdded sealing
washer
51
Hex-head screw M10torque15 Nm – 20 Nm
Situation of mounting
Mounting flange:
31
370–
520
MHz
Special Purpose Antenna406–428 MHzK8134321, K8134322
Tram and Bus Antenna 406–428
Type No. K8134321 K8134322
Input M 11 x 1 female(the connector for cable RG
58 C/U is supplied).
N female
Drill hole dimension
mminches
120.5
170.7
Frequency range MHz 406 – 428 MHzVSWR 406 – 410 MHz: < 1.9
410 – 425 MHz: < 1.7425 – 428 MHz: < 1.9
Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 50 W (at 50 °C ambient temperature)Weight g | lb 400 | 0.9 lbPacking size (outside)
mminches
117 x 117 x 1144.6 x 4.6 x 4.5
Height mminches
702.8
Mounting On a conductive surface 70 x 70 cm | 27.6 x 27.6 inches min.
Material: Radiator and base: Aluminum.Radome: High impact plastic.All screws and nuts: Stainless steel.
Mounting: The drilling diameter is 12 mm except the N connector versions: 17 mm. A special zinc washer ensures a good contact at the edges of the hole.
Special features: All metall parts of this antenna are DC grounded.Extreme robust and car-wash proof vehicular antenna.
32
Special Purpose Antenna410–470 MHzK813132• Low profile broadband antenna in fiberglass radome.
Mounting hole for the connector: 33 (max. 35) mm diameter.Note: Keep mounting surface clear of paint for electrical contact.
Mounting flange:
13 |
0.5
115 | 4.5
43 | 1.7
145 | 5.7
80 |
3.6
32 |
1.3
56 |
2.2
28 |
1.1
nicht lackiertnot painted
nicht lackiertnot painted
DichtungsringSealing O-ring
All dimensions in mm | inches
Type No. K813132
Input N femaleFrequency range MHz 410 – 470VSWR < 1.5Gain dB 0 (ref. to the quarter-wave antenna)Impedance Ω 50Polarization VerticalMax. power W 170 (at 50° C ambient temperature)Radome weight g | lb 159 | 0.4Total weight g | lb 500 | 1.1Packing size (outside)
mminches
151 x 87 x 2105.9 x 3.4 x 8.3
Material: Radiator and Flange: Aluminum.Radome: Fiberglass, colour: Light grey.All screws and nuts: Stainless steel.Sealing: Neoprene and rubber. Note: Don’t use detergents that might harm the sealing.
Mounting: On a conductive surface with a minimum size of 50 x 50 cm | 19.7 x 19.7 inches by means of existing M10 studs.
Grounding andhigh voltage protection:
This antenna, tested by an independent institute, is DC grounded to protect against lightning and high-tension lines.
33
34
Type Type No. Height[mm]
Connector female,type and position
Page
1 x Lowband
2-Port Antenna 790–960 65° 17.5dBi 0°–8°T 91121416V02 2254 7-16, rearside 36
2 x Lowband
4-Port Antenna 698–960698–960
65°65°
15.5dBi15.5dBi
2°–12°T2°–12°T
91121012 1999 4.3-10, bottom 37 +38
4-Port Antenna 698–960698–960
65°65°
16.5dBi16.5dBi
1°–10°T1°–10°T
91121013 2438 4.3-10, bottom 39 +40
TETRA | 1 x Lowband
4-Port Antenna 380–470698–791
88°65°
13dBi16dBi
2°T2°T
91121959 1977 4 x 4.3-10 female 20
1 x Lowband | 1 x Highband
2-Port Antenna 790–9601710–2690
C 65°65°
8dBi9dBi
0°T0°T
91121864 334 7-16, bottom 51
4-Port Antenna 698–9601695–2690
65°65°
10.5dBi13.5dBi
2°T2°T
91121826 603 4.3-10, bottom 52 +53
4-Port Antenna 790–9601710–2690
65°65°
15dBi17.5dBi
0°–16°T2°–10°T
91121775 1403 7-16, bottom 54 +55
4-Port Antenna 790–9601710–2690
65°65°
16dBi18.5dBi
0°–10°T2°–8°T
91121776V01 1997 7-16, bottom 56+57
4-Port Antenna 698–9601710–2690
65°65°
17dBi18.5dBi
1.5°–10°T2°–8°T
91121777V01 2622 7-16, bottom 58 +59
1 x Lowband | 2 x Highband
6-Port Antenna 698–9601695–26901695–2690
65°65°65°
14.5dBi17.5dBi
18dBi
2°–16°T2.5°–12°T2.5°–12°T
91121975 1402 7-16, bottom 62 +63
6-Port Antenna 698–9601695–26901695–2690
65°65°65°
16dBi18dBi18dBi
2°–12°T2.5°–12°T2.5°–12°T
91121976 1921 7-16, bottom 64 +65
6-Port Antenna 698–9601695–26901695–2690
65°65°65°
17dBi18dBi18dBi
1°–10°T2.5°–12°T2.5°–12°T
91121977 2441 7-16, bottom 66 +67
690–2690 MHz
1-Port LogPer Antenna 690–2690 67° 11dBi 0°T 853203V02 300 7-16, bottom 36
Summary – Directional Antennas 700–850 MHz
35
700–
850
MHz
Omni Antennas Type No. Connectorfemale
Height[mm]
Remarks Page
Lowband
1-Port Omni Antenna 806–894 360° 11dBi 0°T 849203 7-16 3237 42
Lowband | Highband
1-Port Omni Antenna 694–960/1695–2700 360° 2dBi 0°T 91121957 N 202 indoor/outdoor 71
Abbreviations:C: Integrated Combiner
Summary – Omni Antennas Indoor Antennas 700–850 MHz
Indoor Antennas Type No. Connectorfemale
Height[mm]
Page
Directional 2-Port
2-Port Indoor Antenna 694–960/1710–2690 80°/65° C 7dBi 91121993 2 x 4.3-10 399 72
Omnidirectional 1-Port
1-Port Omni 380...6000 360° 1–6dBi 92210001 N female 187 27
1-Port Omni 380...6000 360° 1–6dBi 92210002 4.3-10 female 187 27
Omnidirectional 2-Port
2-Port Indoor Antenna 694–5920 360° 2dBi 91121823 2 x 4.3-10 ∅ 320 73
New or changed product
36
1-Port LogPer Antenna 690–2690 67° 11dBi
Type No. 853203V02Frequency range MHz 690 – 880 880 – 960 960 – 1695 1695 – 2200 2200 – 2490 2490 – 2690
VSWR < 1.6 < 1.5 < 1.5 < 1.5 < 1.5 < 1.5
Gain dBi 10.1 10.6 11.0 11.0 11.0 11.0
Impedance Ω 50 50 50 50 50 50
Polarization Vertical Vertical Vertical Vertical Vertical Vertical
Front-to-back ratio db > 25 > 25 > 25 > 25 > 22 > 25
Half-power beam widthhorizontalvertical
°6954
6453
5750
5348
4746
4544
Intermodulation IM3(2 x 43 dBm carrier)
dBc < −150 < −150 < −150 < −150 < −150 < −150
Max. power W 300 300 250 200 170 150Total power W 500 (at 50 °C ambient temperature)
1-Port LogPer AntennaVertical PolarizationHalf-power Beam Width
690–2690V
67°
Mechanical specifications
Input 1 x 7-16 femaleConnector position BottomWind load(at Rated Wind Speed: 150 km/h)
N | lbf Frontal 20 | 4Lateral 210 | 47Rearside 30 | 7
Max. wind velocity km/hmph
241150
Height / width / depth mminches
300 / 155 / 78511.8 / 6.1 / 30.9
Weight kglb
5.512.1
Packing size mminches
360 x 175 x 100014.2 x 6.9 x 39.4
37
700–
850
MHz
For more information about additional mounting accessories please refer to page 85
2-Port AntennaFrequency RangeHPBW
790–960R1
2-Port Antenna LB 2.3m 65° | 790–960 17.5dBi
Type No. 91121416V02Lowband R1
790–960Frequency range MHz 790 – 862 824 – 894 880 – 960Polarization ° +45, –45 +45, –45 +45, –45Average gainTilt
dBi°
16.8 ... 17.0 ... 16.70 ... 4 ... 8
16.9 ... 17.1 ... 16.90 ... 4 ... 8
17.2 ... 17.4 ... 17.00 ... 4 ... 8
Horizontal Pattern:Half-power beam width ° 69 67 65Front-to-back ratio, copolar dB > 25 > 25 > 25Cross polar ratioMaindirection 0°Sector ±60°
dB Typically: 25Typically: > 10
Typically: 25Typically: > 10
Typically: 25Typically: > 10
Tracking, Avg. dB 0.5Squint ° ±2.5Vertical Pattern:Half-power beam width ° 9.1 8.8 8.5Electrical tilt ° 0–8, continuously adjustableSidelobe suppression for first sidelobe above main beam
°TdB
0 ... 2 ... 4 ... 818 ... 18 ... 18 ... 16
0 ... 2 ... 4 ... 818 ... 18 ... 18 ... 16
0 ... 2 ... 4 ... 820 ... 18 ... 17 ... 15
Impedance Ω 50VSWR < 1.5Isolation, between ports dB > 30Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Max. effective power per portMax. effective power for the antenna W 400 (at 50 °C ambient temperature)
800 (at 50 °C ambient temperature)
Mechanical specifications
Input 2 x 7-16 femaleConnector position RearsideAdjustmentmechanism
1x, Position bottomcontinuously adjustable
Wind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 770 | 173Maximal: 845 | 190
Max. wind velocity km/hmph
200124
Height/width/depth mminches
2254 / 259 / 9988.7 / 10.2 / 3.9
Category of mounting hardware M (Medium)Weight kg
lb11.5 / 13.5 (clamps incl.)
25.4 / 29.8 (clamps incl.)Packing size mm
inches2536 x 272 x 14799.8 x 10.7 x 3.9
Scope of supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
38 For more information about additional mounting accessories please refer to page 85
4-Port AntennaFrequency RangeHPBW
698–960698–96065°65°
R2R1
4-Port Antenna 2LB 2.0m 65° | 2x698–960 15.5dBi
Type No. 91121012Left side, lowband R1, connector 1–2
698–960Frequency Range MHz 698 – 806 791 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 14.8 15.4 15.6 15.9Gain over all Tilts dBi 14.8 ± 0.6 15.4 ± 0.4 15.6 ± 0.2 15.8 ± 0.2Horizontal Pattern:Azimuth Beamwidth ° 62 ± 3.9 61 ± 3.2 60 ± 2.7 60 ± 2.1Front-to-Back Ratio,Total Power, ± 30° dB > 22 > 25 > 27 > 25
Cross Polar Discriminationover Sector dB > 8.5 > 10.5 > 11.5 > 11.0
Azimuth Beam Port-to-Port Tracking dB < 1.5 < 1.0 < 1.0 < 1.5
Vertical Pattern:Elevation Beamwidth ° 11.9 ± 0.8 11.0 ± 0.8 10.5 ± 0.4 10.2 ± 0.4Electrical Downtiltcontinuously adjustable ° 2.0 – 12.0
Tilt Accuracy ° < 0.7 < 0.7 < 0.7 < 0.7First Upper Side Lobe Suppression dB > 14 > 14 > 15 > 14
Cross Polar Isolation dB > 30Port to Port Isolation dB > 27 (R1 // R2)Max. Effective Powerper Port W 400 (at 50 °C ambient temperature)
Max. Effective PowerPorts R1 W 800 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
39
700–
850
MHz
For more information about additional mounting accessories please refer to page 85
4-Port Antenna
91121012Right side, lowband R2, connector 3–4
698–960Frequency Range MHz 698 – 806 791 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 14.8 15.3 15.5 15.8Gain over all Tilts dBi 14.8 ± 0.6 15.3 ± 0.3 15.5 ± 0.3 15.7 ± 0.3Horizontal Pattern:Azimuth Beamwidth ° 63 ± 3.6 62 ± 1.8 62 ± 2.1 60 ± 3.7Front-to-Back Ratio,Total Power, ± 30° dB > 22 > 24 > 26 > 27
Cross Polar Discriminationover Sector dB > 8.0 > 12.5 > 13.0 > 13.0
Azimuth Beam Port-to-Port Tracking dB < 1.5 < 1.5 < 1.0 < 2.0
Vertical Pattern:Elevation Beamwidth ° 11.6 ± 0.7 11.0 ± 0.6 10.7 ± 0.4 10.2 ± 0.5Electrical Downtiltcontinuously adjustable ° 2.0 – 12.0
Tilt Accuracy ° < 0.7 < 0.6 < 0.6 < 0.5First Upper Side Lobe Suppression dB > 14 > 16 > 16 > 16
Cross Polar Isolation dB > 30Port to Port Isolation dB > 27 (R2 // R1)Max. Effective Powerper Port W 400 (at 50 °C ambient temperature)
Max. Effective PowerPorts R2 W 800 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Electrical specifications, all systems
Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 27Passive Intermodulation dBc < −153 (2 x 43 dBm carrier)Polarization ° +45, –45Max. Effective Powerfor the Antenna W 1200 (at 50 °C ambient
temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifications
Input 4 x 4.3-10 femaleConnector Position bottomAdjustment Mechanism FlexRET,
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 1130 | 254Maximal: 1140 | 256
Max. Wind Velocity km/hmph
241150
Height / Width / Depth mminches
1999 / 508 / 17578.7 / 20.0 / 6.9
Category of Mounting Hardware XH (X-Heavy)
Weight kglb
41.0 / 46.0 (clamps incl.)90.4 / 101.4 (clamps incl.)
Packing Size mminches
2200 / 542 / 26886.6 / 21.3 / 10.6
Scope of Supply Panel, FlexRET and clampsfor 55–115 mm |
2.2–4.5 inches diameter
The “Category of
Mounting Hardware”
will change to “XM”
during 2018
40 For more information about additional mounting accessories please refer to page 85
4-Port AntennaFrequency RangeHPBW
698–960698–96065°65°
R2R1
4-Port Antenna 2LB 2.4m 65° | 2x698–960 16.5dBi
Type No. 91121013Left side, lowband R1, connector 1–2
698–960Frequency Range MHz 698 – 806 791 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 15.7 16.1 16.4 16.5Gain over all Tilts dBi 15.6 ± 0.4 16.1 ± 0.3 16.3 ± 0.3 16.4 ± 0.3Horizontal Pattern:Azimuth Beamwidth ° 66 ± 2.9 65 ± 2.3 65 ± 2.6 64 ± 2.9Front-to-Back Ratio,Total Power, ± 30° dB > 23 > 23 > 24 > 25
Cross Polar Discriminationover Sector dB > 10.0 > 9.5 > 10.0 > 11.5
Azimuth Beam Port-to-Port Tracking dB < 1.5 < 1.0 < 1.0 < 1.5
Vertical Pattern:Elevation Beamwidth ° 9.7 ± 0.7 9.0 ± 0.5 8.8 ± 0.5 8.3 ± 0.4Electrical Downtiltcontinuously adjustable ° 1.0 – 10.0
Tilt Accuracy ° < 0.4 < 0.4 < 0.4 < 0.4First Upper Side Lobe Suppression dB > 16 > 17 > 17 > 20
Cross Polar Isolation dB > 30Port to Port Isolation dB > 27 (R1 // R2)Max. Effective Powerper Port W 400 (at 50 °C ambient temperature)
Max. Effective PowerPorts R1 W 800 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
41
700–
850
MHz
For more information about additional mounting accessories please refer to page 85
4-Port Antenna
91121013Right side, lowband R2, connector 3–4
698–960Frequency Range MHz 698 – 806 791 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 15.5 16.0 16.3 16.6Gain over all Tilts dBi 15.5 ± 0.5 16.0 ± 0.5 16.3 ± 0.4 16.5 ± 0.3Horizontal Pattern:Azimuth Beamwidth ° 67 ± 3.5 65 ± 2.6 64 ± 3.0 63 ± 4.3Front-to-Back Ratio,Total Power, ± 30° dB > 22 > 23 > 24 > 26
Cross Polar Discriminationover Sector dB > 9.5 > 10.5 > 10.0 > 11.5
Azimuth Beam Port-to-Port Tracking dB < 0.5 < 1.0 < 0.5 < 1.5
Vertical Pattern:Elevation Beamwidth ° 9.9 ± 0.7 9.0 ± 0.7 8.6 ± 0.4 8.1 ± 0.5Electrical Downtiltcontinuously adjustable ° 1.0 – 10.0
Tilt Accuracy ° < 0.4 < 0.4 < 0.4 < 0.3First Upper Side Lobe Suppression dB > 18 > 21 > 20 > 20
Cross Polar Isolation dB > 30Port to Port Isolation dB > 27 (R2 // R1)Max. Effective Powerper Port W 400 (at 50 °C ambient temperature)
Max. Effective PowerPorts R2 W 800 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Electrical specifications, all systems
Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 27Passive Intermodulation dBc < −153 (2 x 43 dBm carrier)Polarization ° +45, –45Max. Effective Powerfor the Antenna W 1200 (at 50 °C ambient
temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifications
Input 4 x 4.3-10 femaleConnector Position bottomAdjustment Mechanism FlexRET,
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 1400 | 315Maximal: 1405 | 316
Max. Wind Velocity km/hmph
241150
Height / Width / Depth mminches
2438 / 508 / 17596.0 / 20.0 / 6.9
Category of Mounting Hardware XH (X-Heavy)
Weight kglb
47.0 / 52.0 (clamps incl.)103.6 / 114.6 (clamps incl.)
Packing Size mminches
2635 / 542 / 268103.7 / 21.3 / 10.6
Scope of Supply Panel, FlexRET and 1 unit of clamps for 55–115 mm |
2.2–4.5 inches diameter
42 Side-mounting brackets see page 86 + 87
1-Port Omni AntennaVertical Polarization
806–894V
Mounting: The antenna can be attached laterally at the tip of a tubular mast of 50–94 mm | 2.0–3.7 inches diameter with two U-bolt brackets supplied with the antenna (connecting cable runs outside the mast).
Material: Radiator: Copper and brass. Radome: Fiberglass, color: Grey.Base: Weather-proof aluminum. Mounting kit, screws and nuts: Stainless steel.
Grounding All metal parts of the antenna as well as the inner conductor and the mounting kit are DC grounded. The inner conductor is capacitively coupled.
Lightning protection: The antenna is designed to withstand a lightning current of up to 150 KA (impulse: 10/350 µs), according to IEC 62305 parts 1–4 and VDE 0855-300, and thereby fulfils the require-ments of lightning protection class II. Grounding cross-section: 22 mm2 copper.
1 50
230
104
maximum
mast top
1-Port Omni 806–894 360° 11dBi
Type No. 849203Frequency range MHz 806 – 894Polarization VerticalGain dBi 11Impedance Ω 50VSWR < 1.5Intermodulation IM3 dBc < −150 ( 2 x 43 dBm carrier)Max. power W 500 (at 50 °C ambient temperature)
Mechanical specifications
Input 7-16 femaleConnector position BottomWind load (at Rated Wind Speed: 150 km/h) N | lbf 230 | 52
Max. wind velocity km/hmph
180112
Height mminches
3237127.4
Radome diameter mminches
512.0
Weight kglb
8.518.7
Packing size mminches
3516 x 148 x 112138.4 x 5.8 x 4.4
3237
mm
| 12
7.4
inch
es
43
44
Type Type No. Height[mm]
Connector female,type and position
Page
690–2690 MHz
1-Port LogPer Antenna 690–2690 67° 11dBi 0°T 853203V02 300 7-16, bottom 36
1 x Highband
2-Port Antenna 1710–2690 65° 9.5dBi 0°T 91121822 155 7-16, bottom or top 46
2-Port Antenna 1710–2690 65° 12dBi 4°T 91121872 278 7-16, bottom 47
2-Port Antenna 1710–2690 65° 16.5dBi 0°–12°T 91121792 851 7-16, bottom 48
2-Port Antenna 1710–2690 65° 18dBi 2°–14°T ESLS 91121732V02 1452 7-16, bottom 49
2-Port Antenna 1710–2690 65° 19dBi 0°–6°T 91121762 1670 7-16, bottom 50
1 x Lowband | 1 x Highband
2-Port Antenna 790–9601710–2690
C 65°65°
8dBi9dBi
0°T0°T
91121864 334 7-16, bottom 51
4-Port Antenna 698–9601695–2690
65°65°
10.5dBi13.5dBi
2°T2°T
91121826 603 4.3-10, bottom 52 +53
4-Port Antenna 790–9601710–2690
65°65°
15dBi17.5dBi
0°–16°T2°–10°T
91121775 1403 7-16, bottom 54 +55
4-Port Antenna 790–9601710–2690
65°65°
16dBi18.5dBi
0°–10°T2°–8°T
91121776V01 1997 7-16, bottom 56+57
4-Port Antenna 698–9601710–2690
65°65°
17dBi18.5dBi
1.5°–10°T2°–8°T
9112177V01 2622 7-16, bottom 58 +59
2 x Highband
4-Port Antenna 1695–26901695–2690
65°65°
18dBi18dBi
2°–14°T2°–14°T
ESLS 91131733 1471 4.3-10, bottom 60 +61
2 x Highband Special Design
4-Port MicroCell 1695–26901695–2690
85°85°
7.5dBi7.5dBi
0°T0°T
91121954 526 4.3-10, bottom and top
68
1 x Lowband | 2 x Highband
6-Port Antenna 698–9601695–26901695–2690
65°65°65°
14.5dBi17.5dBi
18dBi
2°–16°T2.5°–12°T2.5°–12°T
91121975 1402 7-16, bottom 62 +63
6-Port Antenna 698–9601695–26901695–2690
65°65°65°
16dBi18dBi18dBi
2°–12°T2.5°–12°T2.5°–12°T
91121976 1921 7-16, bottom 64 +65
6-Port Antenna 698–9601695–26901695–2690
65°65°65°
17dBi18dBi18dBi
1°–10°T2.5°–12°T2.5°–12°T
91121977 2441 7-16, bottom 66 +67
3 x Highband Special Design
6-Port Tri-Sector Slimpole 1710–2690 80° 10dBi 0°T 91131237 691 4.3-10, bottom 69
Summary – Directional Antennas 2300–2600 MHz
45
2300
–260
0 M
Hz
Omni Antennas Type No. Connectorfemale
Height[mm]
Remarks Page
Highband
1-Port Omni Antenna 1695–2700 360° 2dBi 0°T 91121542 N 115 indoor/outdoor 70
Lowband | Highband
1-Port Omni Antenna 694–960/1695–2700 360° 2dBi 0°T 91121957 N 202 indoor/outdoor 71
Abbreviations:ESLS: Enhanced Side Lobe Suppression (above or below horizon) C: Integrated Combiner
Summary – Omni Antennas Indoor Antennas 2300–2600 MHz
Indoor Antennas Type No. Connectorfemale
Height[mm]
Page
Directional 2-Port
2-Port Indoor Antenna 694–960/1710–2690 80°/65° C 7dBi 91121993 2 x 4.3-10 399 72
Omnidirectional 1-Port
1-Port Omni 380...6000 360° 1–6dBi 92210001 N female 187 27
1-Port Omni 380...6000 360° 1–6dBi 92210002 4.3-10 female 187 27
Omnidirectional 2-Port
2-Port Indoor Antenna 694–5920 360° 2dBi 91121823 2 x 4.3-10 ∅ 320 73
New or changed product
46 For more information about additional mounting accessories please refer to page 85
2-Port AntennaFrequency RangeHPBW
1710–269065°
Y1
2-Port Antenna HB 0.2m 65° | 1710–2690 9.5dBi
Type No. 91121822Highband Y1
1710–2690Frequency range MHz 1710 – 1990 1920 – 2200 2200 – 2490 2490 – 2690Polarization ° +45, –45 +45, –45 +45, –45 +45, –45Gain dBi 8.7 9.2 9.6 9.8Horizontal Pattern:Half-power beam width ° Approx. 67 Approx. 62 Approx. 55 Approx. 53Front-to-back ratio, copolar(180°±30°) dB > 24 > 24 > 22 > 22
Cross polar ratio 0° dB Typically: 20 Typically: 20 Typically: 24 Typically: 24Cross polar ratiosector corner ±60° dB > 10 > 9 > 8 > 8
Vertical Pattern:Half-power beam width ° Approx. 66 Approx. 60 Approx. 55 Approx. 53
Impedance Ω 50VSWR < 1.5Isolation, between ports dB > 27Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Max. power per input W 100 (at 50 °C ambient temperature)Max. power per antenna W 150 (at 50 °C ambient temperature)
Mechanical specifications
Input 2 x 7-16 femaleConnector position * Bottom or topWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 35 | 8Maximal: 35 | 8
Max. wind velocity km/hmph
200124
Height / width / depth mminches
155 / 155 / 696.1 / 6.1 / 2.7
Category of mounting hardware L (Light)
Weight kglb
1.5 (tension bands incl.)3.3 (tension bands incl.)
Packing size mminches
257 x 172 x 9210.1 x 6.8 x 3.6
Scope of Supply Panel and 1 unit of tension bands for 45–125 mm |1.8–4.9 inches diameter
* Inverted mounting: Connector position top: Change drain hole screw
47
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
2-Port AntennaFrequency RangeHPBW
1710–269065°
Y1
2-Port Antenna HB 0.3m 65° | 1710–2690 12dBi
Type No. 91121872Highband Y1
1710–2690Frequency range MHz 1710 – 1990 1920 – 2200 2200 – 2490 2490 – 2690Polarization ° +45, –45 +45, –45 +45, –45 +45, –45Gain dBi 11 11.5 12.2 12.7Horizontal Pattern:Half-power beam width ° 67 65 60 58Front-to-back ratio, copolar dB > 30 > 28 > 28 > 27Cross polar ratio Maindirection 0°Sector ±60°
dB Typically: > 20> 8
Typically: > 20> 8
Typically: > 20> 8
Typically: > 20> 8
Vertical Pattern:Half-power beam width ° 36 31 25 25Electrical tilt ° 3, fixed 3, fixed 4, fixed 4, fixed
Impedance Ω 50VSWR < 1.5Isolation, between ports dB > 28Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Max. power per input W 150 (at 50 °C ambient temperature)
Mechanical specifications
Input 2 x 7-16 femaleConnector position BottomWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 55 | 12Maximal: 55 | 12
Max. wind velocity km/hmph
200124
Height/width/depth mminches
278 / 154 / 6910.9 / 6.1 / 2.7
Category of mounting hardware L (Light)Weight kg
lb1.8 (tension bands incl.)4.0 (tension bands incl.)
Packing size mminches
375 x 172 x 9214.8 x 6.8 x 39.1
Scope of supply Panel and 1 unit of tension bands for 45 – 125 mm | 1.8 – 4.9 inches diameter
48 For more information about additional mounting accessories please refer to page 85
2-Port AntennaFrequency RangeHPBW
1710–269065°
Y1
2-Port Antenna HB 0.9m 65° | 1710–2690 16.5dBi
Type No. 91121792Highband Y1
1710–2690Frequency range MHz 1710 – 1990 1920 – 2200 2200 – 2490 2490 – 2690Polarization ° +45, –45 +45, –45 +45, –45 +45, –45Gain at 0° tilt dBi 15.5 16.3 16.7 16.7Horizontal Pattern:Half-power beam width ° 67 64 60 60Front-to-back ratio (180°±30°) dB > 25 > 25 > 23 > 23Cross polar ratio 0°Sector ±60° dB Typically: 25
> 10Typically: 28
> 8Typically: 28
> 8Typically: 28
> 11Vertical Pattern:Half-power beam width ° 10.8 9.9 8.8 8.4Electrical tilt ° 0–12, continuously adjustableSidelobe suppression for first sidelobe above main beam
°TdB
0 ... 6 ... 12≥ 12 ... 13 ... 15
0 ... 6 ... 12≥ 13 ... 14 ... 15
0 ... 6 ... 12≥ 13 ... 14 ... 16
0 ... 6 ... 12≥ 15 ... 15 ... 17
Impedance Ω 50VSWR < 1.5Isolation, between ports dB > 30Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Max. power per input W 250 (at 50 °C ambient temperature)
Mechanical specifications
Input 2 x 7-16 femaleConnector position BottomAdjustmentmechanism
1x, Position bottomcontinuously adjustable
Wind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 140 | 31Maximal: 155 | 35
Max. wind velocity km/hmph
200124
Height/width/depth mminches
851 / 155 / 7033.5 / 6.1 / 2.8
Category of mounting hardware L (Light)Weight kg
lb5 / 5.2 (clamps incl.)
11.0 / 11.5 (clamps incl.)Packing size mm
inches1146 x 172 x 9245.1 x 6.8 x 3.6
Scope of supply Panel and 1 unit of tension bands for 45 – 125 mm | 1.8 – 4.9 inches diameter
49
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
2-Port AntennaFrequency RangeHPBW
1710–269065°
Y1
2-Port Antenna HB 1.5 m 65° | 1710–2690 18dBi ESLS
Type No. 91121732V02Highband Y1
1710–2690Frequency range MHz 1710 – 1990 1920 – 2200 2200 – 2490 2490 – 2690Polarization ° +45, –45 +45, –45 +45, –45 +45, –45GainTilt
dBi°
17.4 ... 17.6 ... 17.52 ... 8 ... 14
17.9 ... 18.2 ... 18.12 ... 8 ... 14
18.4 ... 18.5 ... 18.52 ... 8 ... 14
18.5 ... 19.0 ... 18.52 ... 8 ... 14
Horizontal Pattern:Half-power beam width ° 68 63 59 58Front-to-back ratio (180°±30°) dB > 25 > 25 > 25 > 25Cross polar ratio 0°Sector ±60° dB Typically: 25
> 10Typically: 24
> 10Typically: 25
> 10Typically: 25
> 10Tracking, Avg. dB 1.5Vertical Pattern:Half-power beam width °° 6.7 6.0 5.3 5.0Electrical tilt 2–14, continuously adjustableSidelobe suppression– for first sidelobe above main beam– within 0°–20° sector above horizon
°TdBdB
2 ... 8 ... 14≥ 18 ... 18 ... 18≥ 17 ... 17 ... 16
2 ... 8 ... 14≥ 18 ... 18 ... 18≥ 17 ... 17 ... 16
2 ... 8 ... 14≥ 18 ... 18 ... 18≥ 17 ... 17 ... 16
2 ... 8 ... 14≥ 18 ... 18 ... 18≥ 17 ... 17 ... 14
Impedance Ω 50VSWR < 1.5Isolation, between ports dB > 30Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Max. effective power per portMax. effective power for the antenna W 250 (at 50 °C ambient temperature)
500 (at 50 °C ambient temperature)
Mechanical specifications
Input 2 x 7-16 femaleConnector position BottomAdjustmentmechanism
1x, Position bottomcontinuously adjustable
Wind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 250 | 57Maximal: 275 | 62
Max. wind velocity km/hmph
200124
Height/width/depth mminches
1452 / 154 / 7057.2 / 6.0 / 2.8
Category of mounting hardware M (Medium)Weight kg
lb6.5 / 8.5 (clamps incl.)4.3 / 18.7 (clamps incl.)
Packing size mminches
1725 x 172 x 927.9 x 6.8 x 3.6
Scope of supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
50 For more information about additional mounting accessories please refer to page 85
2-Port AntennaFrequency RangeHPBW
1710–269065°
Y1
2-Port Antenna HB 1.7m 65° | 1710–2690 19dBi
Type No. 91121762Highband Y1
1710–2690Frequency range MHz 1710 – 1990 1920 – 2170 2170 – 2490 2490 – 2690Polarization ° +45, –45 +45, –45 +45, –45 +45, –45Gain at 0° tilt dB 18.5 19.0 19.4 19.5Horizontal Pattern:Half-power beam width ° 67 63 60 58Front-to-back ratio (180°±30°) dB > 28 > 28 > 25 > 25Cross polar ratio 0°Sector ±60° dB Typically: 25
> 10Typically: 25
> 10Typically: 25
> 10Typically: 28
> 10Tracking, Avg. dB 1.5Squint ° ±3Vertical Pattern:Half-power beam width ° 5.4 4.9 4.3 4.0Electrical tilt ° 0–6, continuously adjustableSidelobe supression for first sidelobe above main beam
°TdB
0 ... 3 ... 6≥ 18 ... 18 ... 17
0 ... 3 ... 6≥ 18 ... 18 ... 16
0 ... 3 ... 6≥ 18 ... 18 ... 16
0 ... 3 ... 6≥ 18 ... 18 ... 17
Impedance Ω 50VSWR < 1.5Isolation, between ports dB > 30Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Max. power per input W 300 (at 50 °C ambient temperature)
Mechanical specifications
Input 2 x 7-16 femaleConnector position BottomAdjustmentmechanism
1x, Position bottomcontinuously adjustable
Wind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 295 | 66Maximal: 325 | 73
Max. wind velocity km/hmph
200124
Height/width/depth mminches
1670 / 155 / 7065.7 / 6.1 / 2.8
Category of mounting hardware M (Medium)Weight kg
lb7 / 9.2 (clamps incl.)
15.4 / 20.3 (clamps incl.)Packing size mm
inches1934 x 172 x 9276.1 x 6.8 x 3.6
Scope of supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
51
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
C C
61-761-7
790–960+45°
1710–2690–45°
790–960–45°
1710–2690+45°
2-Port AntennaFrequency RangeHPBW
Y1R11710–2690790–960
65°65°
2-Port Antenna LB/HB 0.3m C 65° | 790–960 8dBi | 1710–2690 9dBi
Type No. 91121864R1 Y1
790–960 1710–2690Frequency range MHz 790 – 862 824 – 894 880 – 960 1710 – 1990 1920 – 2200 2200 – 2490 2490 – 2690Polarization ° +45, –45 +45, –45 +45, –45 +45, –45 +45, –45 +45, –45 +45, –45Average gain (dBi) dBi 2 x 7.8 2 x 8.0 2 x 8.5 2 x 7.8 2 x 8.9 2 x 8.7 2 x 8.2Horizontal Pattern:Half-power beam width ° 67 65 55 60 62Front-to-back ratio dB Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25 Copolar: > 25Cross polar ratioMaindirection 0°Sector ±60°
dB Typically: 15> 8
Typically: 18> 8
Typically: 20> 8
Typically: 25> 10
Typically: 25> 10
Typically: 25> 10
Typically: 25> 10
Vertical Pattern:Half-power beam width ° 65 75 60 60 65
Impedance Ω 50VSWR < 1.5Isolation: Intrasystem dB > 30 > 30 > 27 > 25Intermodulation IM3 dBc < −150 dBc (2 x 43 dBm carrier)Max. effective power per port W 200 (at 50 °C ambient temperature) 100 (at 50 °C ambient temperature)
Max. effective power for the antenna W 300 (at 50 °C ambient temperature)
Mechanical specifications
Input 2 x 7-16 femaleConnector position BottomWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 100 | 22Maximal: 110 | 25
Max. wind velocity km/hmph
200124
Height / width / depth mminches
334 / 260 / 13613.1 / 10.2 / 5.4
Category of mounting hardware L (Light)
Weight kglb
2.8 (tension bands incl.)6.2 (tension bands incl.)
Packing size mminches
495 x 272 x 15719.5 x 10.7 x 6.2
Scope of Supply Panel and 1 unit of tension bands for 45–125 mm |1.8–4.9 inches diameter
52 For more information about additional mounting accessories please refer to page 85
4-Port AntennaFrequency RangeHPBW
1695–2690Y1
698–960R1
65°65°
4-Port Antenna LB/HB 0.6m 65° | 698–960 10.5dBi | 1695–2690 13.5dBi
Type No. 91121826Lowband R1, connector 1–2
698–960Frequency range MHz 698 – 824 MHz 824 – 894 MHz 880 – 960 MHzPolarization ° +45, –45 +45, –45 +45, –45Average gain dBi 10.1 10.6 10.7Horizontal Pattern:Half-power beam width ° 70 69 69Front-to-back ratioTotal power, ± 30° dB > 23 > 25 > 25
Cross polar ratioMaindirection 0°Sector ±60°
dB Typically: 25> 8
Typically: 28> 10
Typically: 28> 10
Vertical Pattern:Half-power beam width ° 40 36 35Electrical tilt ° 2, fixed
Impedance Ω 50VSWR < 1.5Isolation: Intrasystem dB > 27, typ. > 30 > 30 > 28, typ. > 30Isolation: Intersystem dB > 26, typ. > 30 (R1 // Y1)Intermodulation IM3 dBc < −153 (2 x 43 dBm carrier)Max. effective power per portMax. effective power for the antenna
W250 (at 50 °C ambient temperature)400 (at 50 °C ambient temperature)
53
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
4-Port Antenna
91121826Highband Y1, connector 3–4
1695–2690Frequency range MHz 1695 – 1880 1850 – 1990 1920 – 2180 2200 – 2490 2490 – 2690Polarization ° +45, –45 +45, –45 +45, –45 +45, –45 +45, –45Average gain dBi 13.1 13.7 13.7 13.8 13.6Horizontal Pattern:Half-power beam width ° 62 55 55 55 68Front-to-back ratioTotal power, ± 30° dB > 26 > 27 > 27 > 27 > 25
Cross polar ratioMaindirection 0°Sector ±60°
dB Typically: 25> 10
> 28> 10
28> 10
25> 10
28> 10
Vertical Pattern:Half-power beam width ° 17.6 16.7 15.9 14.5 12.4Electrical tilt ° 2, fixed
Impedance Ω 50VSWR < 1.5Isolation: Intrasystem dB > 26, typ. > 31 > 30, typ. > 31Isolation: Intersystem dB > 30 (Y1 // R1)Intermodulation IM3 dBc < −153 (2 x 43 dBm carrier)Max. effective power per portMax. effective power for the antenna
W200 (at 50 °C ambient temperature)400 (at 50 °C ambient temperature)
Total power for the antenna W 800 (at 50 °C ambient temperature)
Mechanical specifications
Input 4 x 4.3-10 femaleConnector position BottomWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 110 | 25Maximal: 170 | 38
Max. wind velocity km/hmph
241150
Height/width/depth mminches
603 / 300 / 15223.7 / 11.8 / 6.0
Category of mounting hardware M (Medium)Weight kg
lb8.5 / 10.7 (clamps incl.)
18.7 / 23.6 (clamps incl.)Packing size mm
inches845 x 325 x 19333.3 x 12.8 x 7.6
Scope of supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
54 For more information about additional mounting accessories please refer to page 85
4-Port AntennaFrequency RangeHPBW
1710–2690Y1
790–960R1
65°65°
4-Port Antenna LB/HB 1.4m 65° | 790–960 15dBi | 1710–2690 17.5dBi
Type No. 91121775Lowband R1, connector 1–2
790–960Frequency range MHz 790 – 862 824 – 894 880 – 960Polarization ° +45, –45 +45, –45 +45, –45Average gainTilt
dBi°
14.5 ... 14.4 ... 14.20 ... 8 ... 16
14.6 ... 14.5 ... 14.30 ... 8 ... 16
14.8 ... 14.6 ... 14.40 ... 8 ... 16
Horizontal Pattern:Half-power beam width ° 69 68 67°Front-to-back ratio, copolar (180°±30°) dB > 25 > 25 > 25Cross polar ratioMaindirection 0°Sector ±60°
dB Typically: 25> 10
Typically: 25> 9
Typically: 25> 8
Horizontal Pattern:Half-power beam width ° 16.5 16.0 15.5Electrical tilt ° 0–16, continuously adjustableSidelobe suppression for first sidelobe above main beam
° TdB
0 ... 8 ... 1616 ... 15 ... 15
0 ... 8 ... 1616 ... 15 ... 15
0 ... 8 ... 1615 ... 15 ... 14
Impedance Ω 50VSWR < 1.5Isolation: Intrasystem dB > 30Isolation: Intersystem dB > 30 (698–960 // 1710–2690 MHz)Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Max. effective power per portMax. effective power for the antenna W 300 (at 50 °C ambient temperature)
600 (at 50 °C ambient temperature)
55
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
4-Port Antenna
91121775
Mechanical specifications
Input 4 x 7-16 female (long neck)Connector position BottomAdjustment mechanism 2x, Position bottom
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 260 | 58Maximal: 415 | 93
Max. wind velocity km/hmph
200124
Height / width / depth mminches
1403 / 300 / 15255.2 / 11.8 / 6.0
Category of mounting hardware M (Medium)
Weight kglb
18 / 20 (clamps incl.)39.7 / 44.1 (clamps incl.)
Packing size mminches
1726 x 322 x 19068.0 x 12.7 x 7.5
Scope of supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
Highband Y1, connector 3–41710–2690
Frequency range MHz 1710 – 1880 1850 – 1990 1920 – 2170 2300 – 2400 2490 – 2690Polarization ° +45, –45 +45, –45 +45, –45 +45, –45 +45, –45Average gainTilt
dBi°
17.2 ... 17.3 ... 16.82 ... 6 ... 10
17.4 ... 17.4 ... 16.92 ... 6 ... 10
17.6 ... 17.7 ... 17.02 ... 6 ... 10
17.0 ... 16.8 ... 16.02 ... 6 ... 10
17.2 ... 17.3 ... 16.72 ... 6 ... 10
Horizontal Pattern:Half-power beam width ° 63 64 66 73 65Front-to-back ratio, copolar (180°±30°) dB > 25 > 28 > 29 > 26 > 25Cross polar ratioMaindirection 0°Sector ±60°
dBTypically: 18
> 9> 20> 10
20> 10
23> 10
23 > 8
Horizontal Pattern:Half-power beam width ° 6.2 5.8 5.6 5.4 4.8Electrical tilt ° 2–10, continuously adjustableSidelobe suppression for first sidelobe above main beam
°TdB
2 ... 6 ... 1014 ... 15 ... 16
2 ... 6 ... 1014 ... 15 ... 17
2 ... 6 ... 1015 ... 16 ... 17
2 ... 6 ... 1017 ... 18 ... 18
2 ... 6 ... 1015 ... 17 ... 18
Impedance Ω 50VSWR < 1.5Isolation: Intrasystem dB > 28 > 30Isolation: Intersystem dB > 30 (790–960 // 1710–2690 MHz)Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Max. effective power per portMax. effective power for the antenna
W 200 (at 50 °C ambient temperature)400 (at 50 °C ambient temperature)
56 For more information about additional mounting accessories please refer to page 85
4-Port AntennaFrequency RangeHPBW
1710–2690Y1
790–960R1
65°65°
4-Port Antenna LB/HB 2.0m 65° | 790–960 16dBi | 1710–2690 18.5dBi
Type No. 91121776V01Lowband R1, connector 1–2
790–960Frequency Range MHz 790 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 16.1 16.2 16.2Gain over all Tilts dBi 15.9 ± 0.3 16.1 ± 0.2 16.1 ± 0.3Horizontal Pattern:Azimuth Beamwidth ° 69 ± 0.9 68 ± 1.2 67 ± 0.6Front-to-Back Ratio,Total Power, ± 30° dB > 23 > 25 > 26
Cross Polar Discriminationat Boresight dB > 23 > 23 > 20
Cross Polar Discriminationover Sector dB > 9.5 > 10.0 > 11.0
Vertical Pattern:Elevation Beamwidth ° 10.1 ± 0.4 9.9 ± 0.3 9.5 ± 0.4Electrical Downtiltcontinuously adjustable ° 0.0 – 10.0
Tilt Accuracy ° < 0.5 < 0.5 < 0.6First Upper Side Lobe Suppression dB > 16 > 18 > 16
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 16 > 18 > 16
Cross Polar Isolation dB > 30Port to Port Isolation dB > 30 (R1 // Y1)Max. Effective Powerper Port W 400 (at 50 °C ambient temperature)
Max. Effective PowerPorts R1 W 800 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
57
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
4-Port Antenna
91121776V01
Highband Y1, connector 3–41710–2690
Frequency Range MHz 1710 – 1880 1850 – 1990 1920 – 2170 2300 – 2400 2490 – 2690Gain at mid Tilt dBi 18.2 18.5 18.8 18.8 18.7Gain over all Tilts dBi 18.1 ± 0.5 18.4 ± 0.2 18.7 ± 0.5 18.7 ± 0.6 18.5 ± 0.3Horizontal Pattern:Azimuth Beamwidth ° 64 ± 5.4 63 ± 2.7 61 ± 3.6 62 ± 5.7 64 ± 3.4Front-to-Back Ratio,Total Power, ± 30° dB > 25 > 26 > 27 > 26 > 25
Cross Polar Discriminationat Boresight dB > 14 > 19 > 20 > 18 > 20
Cross Polar Discriminationover Sector dB > 8.0 > 9.5 > 10.0 > 10.0 > 11.5
Vertical Pattern:Elevation Beamwidth ° 5.0 ± 0.3 4.7 ± 0.2 4.4 ± 0.3 3.8 ± 0.2 3.5 ± 0.2Electrical Downtiltcontinuously adjustable ° 2.0 – 8.0
Tilt Accuracy ° < 0.2 < 0.2 < 0.3 < 0.2 < 0.3First Upper Side Lobe Suppression dB > 17 > 18 > 19 > 20 > 20
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 15 > 16 > 16 > 15 > 17
Cross Polar Isolation dB > 28Port to Port Isolation dB > 30 (R1 // Y1)Max. Effective Powerper Port W 200 (at 50 °C ambient temperature)
Max. Effective PowerPorts Y1 W 400 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Electrical specifications, all systems
Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 30Passive Intermodulation dBc < −150 (2 x 43 dBm carrier)Polarization ° +45, –45Max. Effective Powerfor the Antenna W 900 (at 50 °C ambient
temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifications
Input 4 x 7-16 female long neckConnector Position bottomAdjustment Mechanism 2x, Position bottom
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 390 | 88Maximal: 620 | 139
Max. Wind Velocity km/hmph
200124
Height / Width / Depth mminches
1997 / 300 / 15278.6 / 11.8 / 6.0
Category of Mounting Hardware M (Medium)
Weight kglb
24.0 / 26.2 (clamps incl.)52.9 / 57.8 (clamps incl.)
Packing Size mminches
2316 / 322 / 19091.2 / 12.7 / 7.5
Scope of Supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
58 For more information about additional mounting accessories please refer to page 85
4-Port AntennaFrequency RangeHPBW
1710–2690Y1
698–960R1
65°65°
4-Port Antenna LB/HB 2.6m 65° | 698–960 17dBi | 1710–2690 18.5dBi
Type No. 91121777V01Lowband R1, connector 1–2
698–960Frequency Range MHz 698 – 806 790 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 16.0 16.6 16.9 17.1Gain over all Tilts dBi 16.0 ± 0.5 16.5 ± 0.4 16.8 ± 0.4 17.0 ± 0.2Horizontal Pattern:Azimuth Beamwidth ° 71 ± 2.2 68 ± 1.0 68 ± 0.9 67 ± 1.5Front-to-Back Ratio,Total Power, ± 30° dB > 22 > 24 > 26 > 27
Cross Polar Discriminationat Boresight dB > 23 > 22 > 22 > 21
Cross Polar Discriminationover Sector dB > 8.0 > 8.5 > 9.5 > 8.5
Vertical Pattern:Elevation Beamwidth ° 8.4 ± 0.7 7.7 ± 0.4 7.5 ± 0.4 7.0 ± 0.3Electrical Downtiltcontinuously adjustable ° 1.5 – 10.0
Tilt Accuracy ° < 0.3 < 0.3 < 0.3 < 0.3First Upper Side Lobe Suppression dB > 16 > 17 > 16 > 15
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 16 > 17 > 16 > 15
Cross Polar Isolation dB > 30Port to Port Isolation dB > 30 (R1 // Y1)Max. Effective Powerper Port W 400 (at 50 °C ambient temperature)
Max. Effective PowerPorts R1 W 800 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
59
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
4-Port Antenna
91121777V01
Highband Y1, connector 3–41710–2690
Frequency Range MHz 1710 – 1880 1850 – 1990 1920 – 2170 2300 – 2400 2490 – 2690Gain at mid Tilt dBi 18.0 18.5 18.8 18.6 19.0Gain over all Tilts dBi 18.0 ± 0.4 18.5 ± 0.4 18.7 ± 0.4 18.5 ± 0.7 18.8 ± 0.4Horizontal Pattern:Azimuth Beamwidth ° 64 ± 3.4 62 ± 2.9 62 ± 2.2 60 ± 4.8 60 ± 2.0Front-to-Back Ratio,Total Power, ± 30° dB > 25 > 26 > 27 > 25 > 26
Cross Polar Discriminationat Boresight dB > 15 > 18 > 20 > 16 > 21
Cross Polar Discriminationover Sector dB > 8.0 > 11.0 > 11.0 > 10.0 > 9.5
Vertical Pattern:Elevation Beamwidth ° 5.0 ± 0.4 4.7 ± 0.2 4.4 ± 0.4 3.9 ± 0.2 3.5 ± 0.2Electrical Downtiltcontinuously adjustable ° 2.0 – 8.0
Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.2 < 0.2First Upper Side Lobe Suppression dB > 19 > 18 > 20 > 20 > 18
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 16 > 16 > 16 > 16 > 17
Cross Polar Isolation dB > 28Port to Port Isolation dB > 30 (R1 // Y1)Max. Effective Powerper Port W 200 (at 50 °C ambient temperature)
Max. Effective PowerPorts Y1 W 400 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Electrical specifications, all systems
Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 30Passive Intermodulation dBc < −150 (2 x 43 dBm carrier)Polarization ° +45, –45Max. Effective Powerfor the Antenna W 900 (at 50 °C ambient
temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifications
Input 4 x 7-16 female long neckConnector Position bottomAdjustment Mechanism 2x, Position bottom
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 530 | 119Maximal: 845 | 190
Max. Wind Velocity km/hmph
200124
Height / Width / Depth mminches
2622 / 300 / 152103.2 / 11.8 / 6.0
Category of Mounting Hardware H (Heavy)
Weight kglb
29.0 / 31.2 (clamps incl.)63.9 / 68.8 (clamps incl.)
Packing Size mminches
2951 / 322 / 190116.2 / 12.7 / 7.5
Scope of Supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
60 For more information about additional mounting accessories please refer to page 85
4-Port AntennaFrequency RangeHPBW
1695–2690Y2
1695–2690Y1
65°65°
4-Port Antenna 2HB 1.5m 65° | 2x1695–2690 18dBi ESLS
Type No. 91131733Left side, highband Y1, connector 1–2
1695–2690Frequency Range MHz 1695 – 1880 1920 – 2180 2300 – 2400 2490 – 2690Gain at mid Tilt dBi 17.4 18.0 18.6 18.8Gain over all Tilts dBi 17.3 ± 0.4 17.9 ± 0.4 18.3 ± 0.4 18.6 ± 0.4Horizontal Pattern:Azimuth Beamwidth ° 66 ± 3.2 63 ± 2.6 60 ± 3.5 56 ± 2.6Front-to-Back Ratio,Total Power, ± 30° dB > 24 > 24 > 26 > 23
Cross Polar Discriminationat Boresight dB > 22 > 22 > 22 > 18
Cross Polar Discriminationover Sector dB > 12.5 > 10.0 > 9.5 > 13.0
Vertical Pattern:Elevation Beamwidth ° 6.8 ± 0.5 6.1 ± 0.5 5.2 ± 0.3 4.9 ± 0.3Electrical Downtiltcontinuously adjustable ° 2.0 – 14.0
Tilt Accuracy ° < 0.3 < 0.3 < 0.2 < 0.2First Upper Side Lobe Suppression dB > 20 > 20 > 20 > 20
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 17 > 17 > 16 > 16
Cross Polar Isolation dB > 30Port to Port Isolation dB > 30 (Y1 // Y2)Max. Effective Powerper Port W 250 (at 50 °C ambient temperature)
Max. Effective PowerPorts Y1 W 500 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
61
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
4-Port Antenna
91131733Right side, highband Y2, connector 3–4
1695–2690Frequency Range MHz 1695 – 1880 1920 – 2180 2300 – 2400 2490 – 2690Gain at mid Tilt dBi 17.2 17.9 18.6 18.9Gain over all Tilts dBi 17.1 ± 0.4 17.8 ± 0.5 18.4 ± 0.4 18.7 ± 0.5Horizontal Pattern:Azimuth Beamwidth ° 68 ± 3.8 64 ± 4.1 59 ± 2.6 55 ± 2.0Front-to-Back Ratio,Total Power, ± 30° dB > 25 > 26 > 25 > 23
Cross Polar Discriminationat Boresight dB > 22 > 22 > 22 > 19
Cross Polar Discriminationover Sector dB > 13.5 > 11.0 > 9.5 > 12.0
Vertical Pattern:Elevation Beamwidth ° 6.8 ± 0.4 6.0 ± 0.5 5.2 ± 0.3 4.8 ± 0.2Electrical Downtiltcontinuously adjustable ° 2.0 – 14.0
Tilt Accuracy ° < 0.3 < 0.3 < 0.2 < 0.2First Upper Side Lobe Suppression dB > 19 > 19 > 20 > 20
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 18 > 17 > 17 > 15
Cross Polar Isolation dB > 30Port to Port Isolation dB > 30 (Y2 // Y1)Max. Effective Powerper Port W 250 (at 50 °C ambient temperature)
Max. Effective PowerPorts Y2 W 500 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Electrical specifications, all systems
Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 30Passive Intermodulation dBc < −153 (2 x 43 dBm carrier)Polarization ° –45, +45Max. Effective Powerfor the Antenna W 700 (at 50 °C ambient
temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifications
Input 4 x 4.3-10 femaleConnector Position bottomAdjustment Mechanism 2x, Position bottom
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 565 | 127Maximal: 620 | 139
Max. Wind Velocity km/hmph
200124
Height / Width / Depth mminches
1471 / 275 / 8657.9 / 10.8 / 3.4
Category of Mounting Hardware M (Medium)
Weight kglb
13.0 / 15.2 (clamps incl.)28.7 / 33.5 (clamps incl.)
Packing Size mminches
1791 / 298 / 11970.5 / 11.7 / 4.7
Scope of Supply Panel and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
62 For more information about additional mounting accessories please refer to page 85
6-Port AntennaFrequency RangeHPBW
1695–2690698–960 1695–269065°65° 65°
Y1 Y2R1
6-Port Antenna LB/2HB 1.4m 65° | 698–960 14.5dBi | 2x1695–2690 18dBi
Type No. 91121975Left side, lowband R1, connector 1–2
698–960Frequency Range MHz 698 – 806 790 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 13.5 14.0 14.2 14.5Gain over all Tilts dBi 13.5 ± 0.3 14.0 ± 0.4 14.2 ± 0.3 14.4 ± 0.3Horizontal Pattern:Azimuth Beamwidth ° 72 ± 3.2 70 ± 2.7 68 ± 2.4 67 ± 2.2Front-to-Back Ratio,Total Power, ± 30° dB > 22 > 24 > 24 > 25
Cross Polar Discriminationat Boresight dB > 23 > 23 > 24 > 22
Cross Polar Discriminationover Sector dB > 7.0 > 7.0 > 7.0 > 7.5
Azimuth Beam Port-to-Port Tracking dB < 2.0 < 1.5 < 2.0 < 2.5
Vertical Pattern:Elevation Beamwidth ° 17.4 ± 1.1 16.2 ± 1.1 15.7 ± 0.7 14.9 ± 0.8Electrical Downtiltcontinuously adjustable ° 2.0 – 16.0
Tilt Accuracy ° < 0.6 < 0.8 < 0.6 < 0.5First Upper Side Lobe Suppression dB > 15 > 16 > 16 > 19
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 22 > 20 > 20 > 20
Cross Polar Isolation dB > 30Port to Port Isolation dB > 30 (R1 // Y1, Y2)Max. Effective Powerper Port W 300 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Left side, highband Y1, connector 3–41695–2690
Frequency Range MHz 1695 – 1880 1850 – 1990 1920 – 2180 2300 – 2400 2500 – 2690Gain at mid Tilt dBi 17.3 17.5 17.6 17.2 17.6Gain over all Tilts dBi 17.2 ± 0.6 17.5 ± 0.3 17.5 ± 0.3 17.1 ± 0.4 17.5 ± 0.6Horizontal Pattern:Azimuth Beamwidth ° 62 ± 3.9 61 ± 3.0 62 ± 3.3 66 ± 6.8 64 ± 5.8Front-to-Back Ratio,Total Power, ± 30° dB > 24 > 28 > 26 > 24 > 24
Cross Polar Discriminationat Boresight dB > 16 > 20 > 23 > 18 > 15
Cross Polar Discriminationover Sector dB > 7.0 > 9.0 > 10.5 > 8.5 > 9.5
Azimuth Beam Port-to-Port Tracking dB < 1.5 < 2.5 < 2.5 < 2.0 < 2.0
Vertical Pattern:Elevation Beamwidth ° 6.7 ± 0.4 6.3 ± 0.3 6.0 ± 0.5 5.3 ± 0.2 4.8 ± 0.3Electrical Downtiltcontinuously adjustable ° 2.5 – 12.0
Tilt Accuracy ° < 0.3 < 0.2 < 0.2 < 0.2 < 0.2First Upper Side Lobe Suppression dB > 17 > 17 > 18 > 19 > 15
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 14 > 14 > 14 > 14 > 14
Cross Polar Isolation dB > 28Port to Port Isolation dB > 30 (Y1 // R1, Y2)Max. Effective Powerper Port W 200 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
63
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
6-Port Antenna
91121975Right side, highband Y2, connector 5–6
1695–2690Frequency Range MHz 1695 – 1880 1850 – 1990 1920 – 2180 2300 – 2400 2500 – 2690Gain at mid Tilt dBi 17.2 17.5 17.8 18.2 18.3Gain over all Tilts dBi 17.2 ± 0.4 17.4 ± 0.3 17.7 ± 0.4 18.1 ± 0.3 18.1 ± 0.4Horizontal Pattern:Azimuth Beamwidth ° 65 ± 2.4 63 ± 3.2 63 ± 2.9 61 ± 2.0 61 ± 2.5Front-to-Back Ratio,Total Power, ± 30° dB > 24 > 23 > 23 > 24 > 25
Cross Polar Discriminationat Boresight dB > 22 > 24 > 24 > 20 > 18
Cross Polar Discriminationover Sector dB > 15.5 > 15.0 > 13.0 > 7.5 > 9.5
Azimuth Beam Port-to-Port Tracking dB < 1.0 < 1.0 < 1.0 < 1.5 < 2.0
Vertical Pattern:Elevation Beamwidth ° 7.1 ± 0.4 6.7 ± 0.4 6.4 ± 0.4 5.5 ± 0.3 5.0 ± 0.3Electrical Downtiltcontinuously adjustable ° 2.5 – 12.0
Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.3 < 0.2First Upper Side Lobe Suppression dB > 21 > 21 > 22 > 18 > 19
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 14 > 15 > 15 > 15 > 16
Cross Polar Isolation dB > 28Port to Port Isolation dB > 30 (Y2 // R1, Y1)Max. Effective Powerper Port W 200 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Electrical specifications, all systems
Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 30Passive Intermodulation dBc < −150 (2 x 43 dBm carrier)Polarization ° +45, –45Max. Effective Powerfor the Antenna W 900 (at 50 °C ambient
temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifications
Input 6 x 7-16 femaleConnector Position bottomAdjustment Mechanism FlexRET,
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 450 | 101Maximal: 520 | 117
Max. Wind Velocity km/hmph
241150
Height / Width / Depth mminches
1402 / 377 / 16955.2 / 14.8 / 6.7
Category of Mounting Hardware H (Heavy)
Weight kglb
25.0 / 27.2 (clamps incl.)55.1 / 59.9 (clamps incl.)
Packing Size mminches
1602 / 397 / 21263.1 / 15.6 / 8.3
Scope of Supply Panel, FlexRET and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
64 For more information about additional mounting accessories please refer to page 85
6-Port AntennaFrequency RangeHPBW
1695–2690698–960 1695–269065°65° 65°
Y1 Y2R1
6-Port Antenna LB/2HB 1.9m 65° | 698–960 16dBi | 2x1695–2690 18dBi
Type No. 91121976Left side, lowband R1, connector 1–2
698–960Frequency Range MHz 698 – 806 790 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 15.2 15.7 15.9 16.2Gain over all Tilts dBi 15.2 ± 0.5 15.6 ± 0.3 15.8 ± 0.4 16.1 ± 0.3Horizontal Pattern:Azimuth Beamwidth ° 69 ± 2.3 68 ± 2.1 67 ± 2.0 67 ± 1.4Front-to-Back Ratio,Total Power, ± 30° dB > 23 > 25 > 26 > 26
Cross Polar Discriminationat Boresight dB > 23 > 22 > 23 > 22
Cross Polar Discriminationover Sector dB > 8.0 > 8.0 > 9.0 > 8.0
Azimuth Beam Port-to-Port Tracking dB < 2.0 < 2.0 < 2.0 < 2.0
Vertical Pattern:Elevation Beamwidth ° 10.8 ± 1.1 9.8 ± 0.4 9.5 ± 0.6 8.9 ± 0.4Electrical Downtiltcontinuously adjustable ° 2.0 – 12.0
Tilt Accuracy ° < 0.5 < 0.5 < 0.4 < 0.5First Upper Side Lobe Suppression dB > 14 > 16 > 16 > 15
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 15 > 16 > 17 > 16
Cross Polar Isolation dB > 30Port to Port Isolation dB > 30 (R1 // Y1 ,Y2)Max. Effective Powerper Port W 400 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Left side, highband Y1, connector 3–41695–2690
Frequency Range MHz 1695 – 1880 1850 – 1990 1920 – 2180 2300 – 2400 2500 – 2690Gain at mid Tilt dBi 17.3 17.7 17.9 17.6 18.1Gain over all Tilts dBi 17.2 ± 0.5 17.6 ± 0.3 17.7 ± 0.3 17.5 ± 0.5 17.9 ± 0.6Horizontal Pattern:Azimuth Beamwidth ° 65 ± 4.2 62 ± 2.6 61 ± 2.4 63 ± 6.1 66 ± 6.8Front-to-Back Ratio,Total Power, ± 30° dB > 26 > 27 > 26 > 23 > 23
Cross Polar Discriminationat Boresight dB > 16 > 20 > 24 > 18 > 15
Cross Polar Discriminationover Sector dB > 7.5 > 8.5 > 10.5 > 8.5 > 9.0
Azimuth Beam Port-to-Port Tracking dB < 2.5 < 2.5 < 2.0 < 2.5 < 2.0
Vertical Pattern:Elevation Beamwidth ° 6.3 ± 0.4 5.9 ± 0.3 5.6 ± 0.4 4.9 ± 0.2 4.4 ± 0.3Electrical Downtiltcontinuously adjustable ° 2.5 – 12.0
Tilt Accuracy ° < 0.2 < 0.2 < 0.2 < 0.1 < 0.1First Upper Side Lobe Suppression dB > 19 > 17 > 17 > 16 > 16
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 14 > 14 > 13 > 13 > 14
Cross Polar Isolation dB > 28Port to Port Isolation dB > 30 (Y1 // R1, Y2)Max. Effective Powerper Port W 200 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
65
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
6-Port Antenna
91121976Right side, highband Y2, connector 5–6
1695–2690Frequency Range MHz 1695 – 1880 1850 – 1990 1920 – 2180 2300 – 2400 2500 – 2690Gain at mid Tilt dBi 17.3 17.5 17.8 18.2 18.1Gain over all Tilts dBi 17.3 ± 0.3 17.5 ± 0.3 17.8 ± 0.4 18.1 ± 0.3 17.9 ± 0.6Horizontal Pattern:Azimuth Beamwidth ° 65 ± 2.9 66 ± 2.8 66 ± 2.6 65 ± 1.8 68 ± 4.8Front-to-Back Ratio,Total Power, ± 30° dB > 22 > 24 > 24 > 25 > 26
Cross Polar Discriminationat Boresight dB > 15 > 19 > 18 > 17 > 19
Cross Polar Discriminationover Sector dB > 10.5 > 15.0 > 14.5 > 10.0 > 10.0
Azimuth Beam Port-to-Port Tracking dB < 1.0 < 1.0 < 1.0 < 0.5 < 2.5
Vertical Pattern:Elevation Beamwidth ° 7.1 ± 0.4 6.7 ± 0.3 6.3 ± 0.5 5.6 ± 0.3 5.0 ± 0.3Electrical Downtiltcontinuously adjustable ° 2.5 – 12.0
Tilt Accuracy ° < 0.3 < 0.3 < 0.3 < 0.3 < 0.3First Upper Side Lobe Suppression dB > 19 > 25 > 25 > 19 > 21
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 13 > 15 > 17 > 17 > 15
Cross Polar Isolation dB > 28Port to Port Isolation dB > 30 (Y2 // R1, Y1)Max. Effective Powerper Port W 200 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Electrical specifications, all systems
Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 30Passive Intermodulation dBc < −150 (2 x 43 dBm carrier)Polarization ° +45, –45Max. Effective Powerfor the Antenna W 900 (at 50 °C ambient
temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifications
Input 6 x 7-16 femaleConnector Position bottomAdjustment Mechanism FlexRET,
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 630 | 142Maximal: 730 | 164
Max. Wind Velocity km/hmph
241150
Height / Width / Depth mminches
1921 / 377 / 16975.6 / 14.8 / 6.7
Category of Mounting Hardware H (Heavy)
Weight kglb
30.0 / 32.2 (clamps incl.)66.1 / 70.9 (clamps incl.)
Packing Size mminches
2121 / 397 / 21283.5 / 15.6 / 8.3
Scope of Supply Panel, FlexRET and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
66 For more information about additional mounting accessories please refer to page 85
6-Port AntennaFrequency RangeHPBW
1710–2690698–960 1710–269065°65° 65°
Y1 Y2R1
6-Port Antenna LB/2HB 2.4m 65° | 698–960 17dBi | 2x1695–2690 18dBi
Type No. 91121977Left side, lowband R1, connector 1–2
698–960Frequency Range MHz 698 – 820 790 – 862 824 – 894 880 – 960Gain at mid Tilt dBi 16.3 16.8 17.0 17.3Gain over all Tilts dBi 16.2 ± 0.5 16.8 ± 0.4 17.0 ± 0.3 17.3 ± 0.2Horizontal Pattern:Azimuth Beamwidth ° 67 ± 2.4 65 ± 1.4 65 ± 0.9 64 ± 1.3Front-to-Back Ratio,Total Power, ± 30° dB > 21 > 24 > 26 > 27
Cross Polar Discriminationat Boresight dB > 24 > 25 > 25 > 26
Cross Polar Discriminationover Sector dB > 6.5 > 7.0 > 9.0 > 10.0
Azimuth Beam Port-to-Port Tracking dB < 2.0 < 2.5 < 2.0 < 2.0
Vertical Pattern:Elevation Beamwidth ° 8.7 ± 0.7 7.9 ± 0.5 7.6 ± 0.4 7.2 ± 0.4Electrical Downtiltcontinuously adjustable ° 1.0 – 10.0
Tilt Accuracy ° < 0.3 < 0.4 < 0.4 < 0.4First Upper Side Lobe Suppression dB > 17 > 17 > 17 > 18
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 16 > 15 > 15 > 16
Cross Polar Isolation dB > 30Port to Port Isolation dB > 30 (R1 // Y1 ,Y2)Max. Effective Powerper Port W 400 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Left side, highband Y1, connector 3–41695–2690
Frequency Range MHz 1695 – 1880 1850 – 1990 1920 – 2180 2300 – 2400 2490 – 2690Gain at mid Tilt dBi 17.4 17.9 17.9 17.3 18.1Gain over all Tilts dBi 17.3 ± 0.5 17.8 ± 0.3 17.8 ± 0.3 17.2 ± 0.2 17.9 ± 0.7Horizontal Pattern:Azimuth Beamwidth ° 65 ± 4.5 62 ± 3.0 62 ± 2.6 69 ± 4.9 63 ± 6.4Front-to-Back Ratio,Total Power, ± 30° dB > 25 > 25 > 25 > 24 > 23
Cross Polar Discriminationat Boresight dB > 16 > 22 > 24 > 19 > 16
Cross Polar Discriminationover Sector dB > 8.5 > 10.5 > 11.0 > 8.5 > 7.5
Azimuth Beam Port-to-Port Tracking dB < 1.5 < 2.5 < 2.0 < 1.5 < 2.5
Vertical Pattern:Elevation Beamwidth ° 6.3 ± 0.4 5.9 ± 0.2 5.6 ± 0.4 4.9 ± 0.1 4.5 ± 0.3Electrical Downtiltcontinuously adjustable ° 2.5 – 12.0
Tilt Accuracy ° < 0.5 < 0.4 < 0.4 < 0.3 < 0.3First Upper Side Lobe Suppression dB > 19 > 18 > 17 > 16 > 18
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 13 > 14 > 13 > 14 > 15
Cross Polar Isolation dB > 28Port to Port Isolation dB > 30 (Y1 // R1, Y2)Max. Effective Powerper Port W 200 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
67
2300
–260
0 M
Hz
For more information about additional mounting accessories please refer to page 85
6-Port Antenna
91121977Right side, highband Y2, connector 5–6
1695–2690Frequency Range MHz 1695 – 1880 1850 – 1990 1920 – 2180 2300 – 2400 2490 – 2690Gain at mid Tilt dBi 17.4 17.7 18.0 18.4 18.6Gain over all Tilts dBi 17.4 ± 0.3 17.6 ± 0.3 17.9 ± 0.5 18.3 ± 0.3 18.4 ± 0.5Horizontal Pattern:Azimuth Beamwidth ° 62 ± 2.3 62 ± 2.0 61 ± 1.9 60 ± 1.7 58 ± 3.6Front-to-Back Ratio,Total Power, ± 30° dB > 24 > 25 > 25 > 25 > 23
Cross Polar Discriminationat Boresight dB > 22 > 23 > 21 > 16 > 16
Cross Polar Discriminationover Sector dB > 16.0 > 16.0 > 13.0 > 8.0 > 7.5
Azimuth Beam Port-to-Port Tracking dB < 1.5 < 1.0 < 1.0 < 1.5 < 2.0
Vertical Pattern:Elevation Beamwidth ° 7.1 ± 0.4 6.6 ± 0.3 6.3 ± 0.4 5.6 ± 0.4 5.0 ± 0.3Electrical Downtiltcontinuously adjustable ° 2.5 – 12.0
Tilt Accuracy ° < 0.2 < 0.3 < 0.3 < 0.4 < 0.2First Upper Side Lobe Suppression dB > 21 > 24 > 23 > 19 > 23
Upper Side Lobe Suppression, 20° Sector above Main Beam
dB > 14 > 15 > 15 > 15 > 17
Cross Polar Isolation dB > 28Port to Port Isolation dB > 30 (Y2 // R1, Y1)Max. Effective Powerper Port W 200 (at 50 °C ambient temperature)
Values based on NGMN-P-BASTA (version 9.6) requirements.
Electrical specifications, all systems
Impedance Ω 50VSWR < 1.5Return Loss dB > 14Interband Isolation dB > 30Passive Intermodulation dBc < −150 (2 x 43 dBm carrier)Polarization ° +45, –45Max. Effective Powerfor the Antenna W 900 (at 50 °C ambient
temperature)Values based on NGMN-P-BASTA (version 9.6) requirements.
Mechanical specifications
Input 6 x 7-16 femaleConnector Position bottomAdjustment Mechanism FlexRET,
continuously adjustableWind load (at Rated Wind Speed: 150 km/h)
N | lbf Frontal: 830 | 187Maximal: 960 | 216
Max. Wind Velocity km/hmph
200124
Height / Width / Depth mminches
2441 / 377 / 16996.1 / 14.8 / 6.7
Category of Mounting Hardware H (Heavy)
Weight kglb
35.0 / 37.2 (clamps incl.)77.1 / 81.9 (clamps incl.)
Packing Size mminches
2641 / 397 / 212104.0 / 15.6 / 8.3
Scope of Supply Panel, FlexRET and 2 units of clamps for 42–115 mm |
1.7–4.5 inches diameter
68
4-Port Micro Cell AntennaDual PolarizationHPBW
Mechanical specifications
Input 4 x 4.3-10 female(2 x top, 2 x bottom,covered by end cap)
Adjustment mechanism
Two continuously rotatable antenna modules (radiator and reflector) within the radome (set by hand)
Tilt adjustment mechanism (installation at right angle)
Set by handContinuously for each sector
(0° … 360°)
Azimuth adjustment mechanism (upright installation)
Set by handContinuously for each sector
(0° … 360°)IP Protection class IP65Wind load(at 150 km/h)
Nlbf
255.6
Max. wind velocity
km/hmph
16099.4
Feeder cables Max. ¼˝ High Flex (bending radius ≤ 25 mm | ≤ 1.0 inches)
push pull and handscrew type, angular connector required
Allowed dia meter of mounting pole
mminches
≥ 40≥ 1.6
Max. distance wall/pole when mounted
mminches
1907.5
Height / diameter
mminches
526 / 10020.7 / 3.9
Category ofmounting hardware L (Light)
Weight kglb
2.04.4
Packing size mminches
547 / 242 / 17421.5 / 9.5 / 6.9
1695–2690 1695–2690X X
85° 85°
Antenna in upright pole installation
Connectors (4.3-10)covered by end cap
1695 - 2690
Top view / connector view
4-Port Micro Cell Antenna 2HB 0.5m 85° | 2x1695–2690 7.5dBi
Type No. 91121954Use case Flexible Indoor Coverage
Flexible Street Level Micro Cell CoverageNot for Macro Site Installation
Pole and wall mountingElectrical data Per sector
1695–2690Frequency range MHz 1695 – 2690Polarization ° +45, –45Gain dBi 7.5Horizontal Pattern:Half-power beam width ° 85Cross polar ratio 0°
60°dB ≥ 18 typ.
≥ 8 typ.Vertical Pattern:Half-power beam width ° 80Electrical tilt(upright installation)
° 0, fixed
Impedance Ω 50 ΩVSWR 1695–1710 MHz: < 1.6
1710–2200 MHz: < 1.52200–2690 MHz: < 1.6
Isolation, between all ports
dB ≥ 25 (Intra- / Intersystem)
Intermodulation IM3 dBc < −153 (2 x 43 dBm carrier)Max. power per input W 50 (at 50 °C ambient temperature)
69
2300
–260
0 M
Hz
2-Port Omni Slimpole 1710–2690 360° 5dBi
Type No. 911212371710–2690
Frequency range MHz 1710 – 1990 1920 – 2170 2170 – 2490 2490 – 2690Polarization ° +45, –45 +45, –45 +45, –45 +45, –45Gain dBi 2 x 5 2 x 5 2 x 5 2 x 5Horizontal Pattern:Half-power beam width Omni Omni Omni OmniDeviation from circularity
dB ±1 ±1 ±1.5 ±1.5
Vertical Pattern:Half-power beam width
° 42 40 36 33
Electrical tilt ° 0, fixed
Impedance Ω 50VSWR < 1.5Isolation, between ports
dB > 30
Intermodulation IM3 dBc 80010126: < −150 (2 x 43 dBm carrier)Max. power per input W 100 (at 50 °C ambient temperature)
Omni Slimpole AntennaDual PolarizationHPBW
1710–2690X
360°
Mechanical specifications
Input 2 x N femaleConnector position BottomWeight kg
lb2.35.1
Wind load (at 150 km/h)
Nlbf
5011.2
Max. wind velocity km/hmph
200124
Mechanical interface Flange connection 8 x M6at a graduated diameter of
136 mm | 5.4 inches.Evenness of the opposite surface:
0.5 mm | 0.02 inchesPacking size mm
inches740 x 220 x 22029.1 x 8.7 x 8.7
Height / diameter mminches
691 / 10027.2 / 3.9
691 m
m |
27.
2 in
ches
70
1-Port Omni AntennaVertical PolarizationIndoor and outdoor use
1695–2700V
1-Port Omni Antenna HB 0.1m 360° | 1695–2700 2dBi
Type No. 91121542Input 1 x N femaleConnector position Bottom or topFrequency range MHz 1695 – 2700VSWR < 1.8Gain dBi 2Impedance Ω 50Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Polarization VerticalMax. power W 50 (at 50 °C ambient temperature)Weight g
lb1500.33
Radome diameter mminches
200.8
Height mminches
1154.5
Fire load kWh 0.07
Material: Radiator: Brass.Radome: Fiberglass, color: White.
Mounting: One hole mounting (16 mm | 0.6 iches diameter) to surfaces of max. 10 mm | 0.4 inches thick-ness.
Grounding: All metal parts of the antenna and the mounting kit are DC grounded. The inner conductor is not DC grounded.
115
mm
| 4
.5 in
ches
71
1-Port Omni AntennaVertical PolarizationIndoor and outdoor use
694–960/1695–2700V
1-Port Omni Antenna LB/HB 0.2m 360° | 694–960/1695–2700 2dBi
Type No. 91121957Input 1 x N femaleConnector position Bottom or topFrequency range MHz 694 – 960 / 1695 – 2700VSWR MHz 694 – 864
< 2.0864 – 894
< 2.2894 – 960
< 2.51695 – 2700
< 2.0Gain dBi 2Impedance Ω 50Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Polarization VerticalMax. power W 50 (at 50 °C ambient temperature)Weight g
lb2100.46
Wind load(at 150 km/h)
Nlbf
61.3
Radome diameter mminches
301.2
Height mminches
2028.0
Fire load kWh 0.2
Material: Radiator: Brass.Radome: Fiberglass, colour: White.
Mounting: One hole mounting (16 mm | 0.6 inches diameter) to surfaces of max. 10 mm | 0.4 inches thickness.
202
mm
| 8
.0 in
ches
72
2-Port Indoor AntennaDual PolarizationHPBWIntegrated Combiner
1710–2690694–960XX
65°80°C
C
4.3-10
694–960–45°
1710–2690–45°
C
4.3-10
694–960+45°
1710–2690+45°
2-Port Indoor Antenna LB/HB C 0.4m 80°/65° | 694–960 7dBi | 710–2690 8dBi
Type No. 91121993Frequency range MHz 694 – 960 1710 – 2690Polarization ° +45, –45 +45, –45Gain dBi 7 8Half-power beam width; hor., ver. ° typ. 80 typ. 65
Impedance Ω 50VSWR 694 – 960 MHz: ≤ 2.2
1710 – 2690 MHz: ≤ 2.2Isolation, between ports dB
694 – 806 MHz: ≥ 16 806 – 960 MHz: ≥ 201710 – 2690 MHz: ≥ 20
Max. power per port W 20 (at 50 °C ambient temperature)Passive Inter-modulation PIM 3 dBc < −140 (at 2 x 40 dBm carrier)
Input 2 x 4.3-10 femaleProtection class IP 30Weight kg | lb 1.6 | 3.5Packing size mm
inches417 / 281 / 14116.4 / 11.1 / 5.6
Height/width/depth mminches
399 / 237 / 6315.7 / 9.3 / 2.5
Operating temperature range °C −5 … +55
Fire protection classification UL 94-V2Fire load kWh 5.3
Material: Reflector: Brass.Radome: ASA / PC, colour: White.
Mounting: Position: Wall and ceiling possible.The antenna is mounted with four screws (4.5 mm | 0.18 inches nominal diameter, srew head dia meter max. 9 mm | 0.35 inches). Screws are not supplied. After antenna mounting install the antenna cover.
Available accessories: Broadband power splitters and tappers (380–5920 MHz).
Antenna rearside with four drilling holes
All dimensions in mm | inches
Antenna and antenna cover
260
| 10.
2
205 | 8.1
73
2-Port IndoorMIMO Omni AntennaVertical Polarization
694–5920 694–5920
V V
2-Port Indoor Omni Antenna 694–5920 360° 2dBi
Type No. 91121823Frequency rangePort 1 and Port 2
MHz Port 1694 – 9601427 – 15181695 – 26903400 – 38004920 – 5920
Port 2694 – 9601427 – 15181695 – 26903400 – 38004920 – 5920
Polarization Dual VerticalGain, typ. dBi 2Gain, max. dBi 694 – 960 MHz: 4.0 – 5.5
1427 – 1518 MHz: 5.0 – 5.51695 – 2690 MHz: 5.0 – 7.53400 – 3800 MHz: 5.5 – 7.04920 – 5920 MHz: 7.0 – 8.0
Impedance Ω 50VSWR 694 – 960 MHz: < 2.0
1427 – 1518 MHz: < 2.01695 – 2690 MHz: < 2.03400 – 3800 MHz: < 2.04920 – 5920 MHz: < 2.0
Isolation dB 694 – 960 MHz: > 201427 – 1518 MHz: > 201695 – 2690 MHz: > 203400 – 3800 MHz: > 204920 – 5920 MHz: > 20
Intermodulation IM3(2 x 40 dBm carrier)
dBc 694 – 960 MHz: < −1501427 – 1518 MHz: < −1501695 – 2690 MHz: < −1503400 – 3800 MHz: < −150
4920 – 5920 MHz: not relevantMax. power per input(at 50 °C ambient temperature)
W 694 – 960 MHz: 201427 – 1518 MHz: 201695 – 2690 MHz: 203400 – 3800 MHz: 104920 – 5920 MHz: 5
Max. effektive power for the antenna
W 20(at 50 °C ambient temperature)
Input 2 x 4.3-10 female(angular connector required)
Protection class IP 30Weight g
lb9502.1
Packing size mminches
350 x 350 x 15013.8 x 13.8 x 5.9
Diameter (antenna module)
mminches
32012.6
Height (antenna module)
mminches
893.5
Fire load kWh 3.18
Material: Reflector: Aluminum.Radome: ASA/PC blend, colour: White. Additional painting is possible.
Mounting: – On-ceiling mounting: Mounting kit 85010200 required
– Concealed antenna installation (ceiling thickness 3–35 mm | 0.12–1.38 inches): Mounting kit 85010201 required
– Hidden antenna installation in double l ayer ceiling, floors or similar – no additional mounting kit required
Accessories (order separately if required)
Type No. Description
85010200 On-ceiling mounting kit85010201 Support ring for concealed antenna
installation
• The antenna can be operated in all indicated frequency ranges simultaneously.
74
75
Acce
ssor
ies
Type Type No. Frequencyrange
Remark Max.power
Connector female
Page
Splitters
2-way Splitter 350–3800 92210012 350–3800 MHz Indoor/Outdoor 300 W 4.3-10 76 + 77
3-way Splitter 350–3800 92210013 350–3800 MHz Indoor/Outdoor 300 W 4.3-10 76 + 77
4-way Splitter 350–3800 92210014 350–3800 MHz Indoor/Outdoor 300 W 4.3-10 76 + 77
2-way Splitter 380–3800 97121242 380–3800 MHz Indoor/Outdoor 700 W 7-16 78
3-way Splitter 380–512 K7431348 380–512 MHz Indoor/Outdoor 1000 W 7-16 79
4-way Splitter 380–512 K7431358 380–512 MHz Indoor/Outdoor 1000 W 7-16 79
2-way Splitter 694–3800 97131128 694–3800 MHz Indoor/Outdoor 100 W 4.3-10 80
3-way Splitter 694–3800 97131129 694–3800 MHz Indoor/Outdoor 100 W 4.3-10 80
4-way Splitter 694–3800 97131120 694–3800 MHz Indoor/Outdoor 100 W 4.3-10 80
Tappers – Continuously adjustable ratio
Multi-band Tapper 380–960/1695–2700/ 3400–3800/4920–5920
5.0–20.0dB
97131271 380–960 MHz1695–2700 MHz3400–3800 MHz4920–5920 MHz
Indoor/Outdoor 100 W 4.3-10 81
Dual-Band Combiners
Dual-Band Combiner (PMR, TETRA, TETRAPOL, CDMA 800, GSM 900, GSM 1800, UMTS, WLAN)
89321571 50–470 MHz790–2500 MHz
Indoor/Outdoor 500 W 7-16 82 +83
More Combiners on request available
Low Noise Amplifier GPS
Low Noise Amplifier GPS 97121253 1575.42 MHz TNCN
84
Mechanical Accessories and Remote Electrical Tilt
Product Line of Mounting Parts for Panel Antennas 85
Side-mounting Brackets for Omni Antennas 86 + 87
Kathrein’s Remote Electrical Tilt System (RET) 88 + 89
New or changed product
Summary – Splitters, Tappers, Dual-Band Combiners, Low Noise Amplifier
76
734365
Mounting material (order separately)
Type Description Remarks
92210015 Mounting kit734365 1 clamp Mast: 45–125 mm diameter
Low-loss Power SplittersMulti-bandConnector 4.3-10
350–3800
For indoor and outdoor use.
2-way Splitter 350–38003-way Splitter 350–38004-way Splitter 350–3800
Type No. 92210012 92210013 92210014Connectors 4.3-10 socket (50 Ω)Max. power (at 50 °C ambient temperature)
300 W
For connecting ... antennas 2 3 4Frequency range 350 – 3800 MHzVSWR ≤ 1.25 (Port 1) ≤ 1.25 (Port 1) ≤ 1.35 (Port 1)Intermodulation IM3 ≤ −155 dBc (2 x 20 W) | typical: ≤ −160 dBcImpedance 50 ΩInsertion loss < 0.05 dBWeight (without mounting kit)
964 g 1045 g 1134 g
Dimensions (w x h x d) See drawings on following page
Mounting: Indoor use: No additional mounting material is necessary.Outdoor use: Mounting material is listed below (order separately).
DC capability: DC transmission between all terminations (suitable for remote power supply systems).
Environmental conditions: ETS 300 019-1-1 class 1.2ETS 300 019-1-2 class 2.3ETS 300 019-1-4 class 4.1 E– Low temperature: –30 °C– High temperature (dry): +65 °CIP 65
92210012 92210013 92210014
92210015
77
Acce
ssor
ies
Low-loss Power SplittersMulti-band
350–3800
92210012
92210013
92210014
wallmast-mounting kit(Option) BN 92210015
wallmast-mounting kit(Option) BN 92210015
wallmast-mounting kit(Option) BN 92210015
78
2-way Splitter 380–3800
Type No. 97121242Connector (female) 7-16Max. power 700 W
(at 50 °C ambient temperature)For connecting ... antennas 2Frequency range 380 – 3800 MHzVSWR < 1.5Intermodulation IM3 < −150 dBc (2 x 43 dBm carrier)Impedance 50 ΩInsertion loss < 0.05 dBWeight 870 gPacking size 300 x 75 x 75 mm
Material: Brass. Surface treatment: CuSnZn3
Mounting: Bracket for wall mounting included in the scope of supply. For pipe mast mounting use clamps listed below (order separately).
DC capability: DC transmission between all terminations (suitable for remote power supply systems).
Environmental conditions: ETS 300 019-1-4 class 4.1 E– Low temperature: –55 °C– High temperature (dry): +60 °CIP 65
For indoor and outdoor use.
34 14.5 15
input
61
735
SW 2486010131
86010130
260
input
SW 24
263.5
36 11
54
13.5
736805
Clamps (order separately)
Type Description Remarks
736801 1 clamp Mast: 34–60 mm diameter736802 1 clamp Mast: 60 –80 mm diameter736803 1 clamp Mast: 80 – 100 mm diameter736804 1 clamp Mast: 100 – 120 mm diameter736805 1 clamp Mast: 120 – 140 mm diameter
Low-loss Power SplittersMulti-band
380–3800
79
Acce
ssor
ies
Power Splitters
For indoor and outdoor use.
380–512
3-way Splitter 380–5124-way Splitter 380–512
Type No. K7431348 K7431358Connector (female) 7-16 7-16Max. power 1000 W
(at 50 °C ambient temperature)For connecting ... antennas 3 4Frequency range 380 – 512 MHzVSWR < 1.1Impedance 50 ΩInsertion loss < 0.05 dBMax. size (mm) [inches]
409 x 82 x 82[16.1 x 3.2 x 3.2]
Packing size (mm) [inches]
425 x 93 x 107[16.7 x 3.7 x 4.2]
Material: Case: Aluminum.Inner conductor: Brass.
Mounting: Bracket for wall mounting included in the scope of supply.For mounting to tubular masts use clamps as listed below(order separately).
734364
Clamps (order separately)
Type Description Remarks(mm) [inches]
734360 2 clamps Mast diameter: 30–55 [1. –2.2]734361 2 clamps Mast diameter: 55–75 [2.2–2.9]734362 2 clamps Mast diameter: 75–95 [2.9– .7]734363 2 clamps Mast diameter: 95–115 [3.7–4.5]734364 2 clamps Mast diameter: 115– 35 [4.5–4.3]
K7431358
80
For indoor and outdoor use.
Low-loss Power SplittersMulti-band
694–3800
Input97131120
2-way Splitter 694–38003-way Splitter 694–38004-way Splitter 694–3800
Type No. 97131128 97131129 97131120Frequency range MHz 694 – 3800For connecting ... antennas 2 3 4Insertion loss dB < 0.05Impedance Ω 50VSWR 694–2100 MHz
2100–2700 MHz2700–3800 MHz
< 1.3< 1.3< 1.5
< 1.3< 1.4< 1.5
< 1.3< 1.3< 1.6
Intermodulation IM3 dBc < −150 (2 x 43 dBm carrier)Max. power W 100 (at 50 °C ambient temperature)Connector 4.3-10 femaleWeight kg
lb0.420.93
0.450.99
0.481.06
Profile cross-section mminches
25 x 251.0 x 1.0
Packing size mminches
248 x 73 x 869.8 x 2.9 x 3.4
Max. size mminches
237 / 66 / 469.3 / 2.6 / 1.8
Material: Housing: Aluminum.Inner conductor: Brass.
DC capability: DC transmission between all terminations (suitbale for remote power supply systems).
Environmental conditions: IP 65
81
Acce
ssor
ies
Multi-band Low-loss Power TapperContinuously Adjustable Splitting Ratio
380–960 / 1695–2700 / 3400–3800 / 4920–5920
5.0 dB – 20.0 dB
2-way Tapper 380–960/1695–2700/3400–3800/4920–5920
Type No. 97131271Frequency range MHz 380 – 960
1695 – 27003400 – 38004920 – 5920
Power ratio between outputs (P2 / P1)
dB –5 to –20continuously adjustable
For connecting ... antennas 2Insertion loss dB 380 – 960 MHz: < 0.2
1695 – 2700 MHz: < 0.23400 – 3800 MHz: < 0.54920 – 5920 MHz: < 0.7
Impedance Ω 50VSWR 380 – 960 MHz: < 1.5
1695 – 2700 MHz: < 1.53400 – 3800 MHz: < 1.74920 – 5920 MHz: < 1.7
Intermodulation IM3 dBc 380 – 960 MHz: < −150 ( 2 x 43 dBm carrier)1695 – 2700 MHz: < −150 ( 2 x 43 dBm carrier)3400 – 3800 MHz: < −150 ( 2 x 43 dBm carrier)4920 – 5920 MHz: not relevant
Max. power W 100 (at 50 °C ambient temperature)Connector 4.3-10 femaleWeight kg
lb0.40.9
Environmental conditions Indoor, outdoor useProtection class IP 65Profile diameter mm
inches502.0
Packing size mminches
225 x 80 x 628.9 x 5.0 x 2.4
Max. size (including connectors)
mminches
160 / 63 / 526.3 / 2.5 / 2.0
Material: Housing: Aluminum.Inner conductor: Brass.
DC capability: DC transmission only between input and port P1.
For indoor and outdoor use.
Input97131271
P2
P1
Blocking unit
Power ratio scale(P2/P1)
Power ratio adjustment mechanism
Splitting table (typical values)
P2 / P1 [dB]Splitting ratio
P1 / P2
Splitting attenuationP1 / PInput [dB] P2 / PInput [dB]
−5 3.2 −1.3 −6.3−6 4 −1.05 −7.05−7 5 −0.85 −7.85−8 6.3 −0.7 −8.7−9 8 −0.6 −9.6−10 10 −0.5 −10.5−11 12.6 −0.4 −11.4−12 15.8 −0.35 −12.35−13 20 −0.25 −13.25−14 25.1 −0.2 −14.2−15 31.6 −0.15 −15.15−16 39.8 −0.14 −16.14−17 50.1 −0.12 −17.12−18 63.1 −0.11 −18.11−19 79.4 −0.1 −19.1−20 100.0 −0.09 −20.09
82
Dual-Band Combiner
Technical Data
Type No. 89321571Pass band Band 1 Band 2
50 – 470 MHz790 – 2500 MHz
Insertion loss Port 1 ↔ Port 3 Port 2 ↔ Port 3
< 0.15 dB (50 – 470 MHz)< 0.15 dB (790 – 2500 MHz)
Isolation Port 1 ↔ Port 2 > 50 dB (50 – 470 / 790 – 2500 MHz)VSWR < 1.25 (50 – 470 / 790 – 960 / 1710 – 2500 MHz)Impedance 50 ΩInput power Band 1 / Band 2 < 500 W / < 500 WIntermodulation products < −160 dBc (3rd order; with 2 x 20 W)Temperature range −55 ... +60 °CConnectors 7-16 female (long neck)Application Indoor or outdoor (IP 66)DC/AISG transparency Port 1 ↔ Port 3 Port 2 ↔ Port 3
By-pass (max. 2500 mA)Stop
Mounting Wall mounting: With 4 screws (max. 8 mm diameter) / Mast mounting: With additional clamp setWeight 4.0 kgPacking size 210 x 150 x 440 mmDimensions (w x h x d) 122 x 64 x 364.3 mm (including mounting brackets)
• Designed for co-siting purposes• Enables feeder sharing• Can be used as a combiner near the BTS or
in a reciprocal function near the antenna• Suitable for indoor or outdoor applications• Wall or mast mounting• External DC stop available as an accessory• Very low insertion loss• High input power
790–2500 MHzCDMA 800 / GSM 900 / GSM 1800 / UMTS / WLAN
50–470 MHzPMR / TETRA / TETRAPOL
Port 1
Port 2
Port 3
Port 2790–2500
Port 150–470
Port 3
83
Acce
ssor
ies
Accessories (order separately)Type No. Clamp set suitable for
mast diameter of734360 34–60 mm734361 60–80 mm734362 80–100 mm734363 100–120 mm734364 120–140 mm734365 45–125 mm
Type No. Description78210850V01 DC stop78410367 50-Ohm load
Dual-Band Combiner
790–2500 MHzCDMA 800 / GSM 900 / GSM 1800 / UMTS / WLAN
50–470 MHzPMR / TETRA / TETRAPOL
Diagram IIPort 1 ↔ Port 3 Port 2 ↔ Port 3
0
10
20
30
40
50
60
70
80
90
100
Atte
nuat
ion/
dB
Frequency/MHz0 250 500 750 1000 1250 1500 1750 2000 2250 2500
50 – 470 806 – 2500
Diagram IIPort 1 ↔ Port 3 Port 2 ↔ Port 3
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.00 250 500 750 1000 1250 1500 1750 2000 2250 2500
Atte
nuat
ion/
dB
Frequency/MHz
806 – 2500 50 – 470
Port 3
Port 1
Port 2
Á
®
¯
¬
Clamp Set
DC Stop 50-Ohm load
84
53 | 2.1
70 | 2.8
22 |
0.9
1)
2)50
| 2
.0
3)
30 |
1.2
Input (Antenna)
TNC
93 |
3.7
Output(DC +3.3 ... 5.5 V)
N
Hanging installation position
bottom
top
ceiling
1) 5 | 0.22) 4.4 | 0.173) 7 | 0.28
All dimensions in mm | inches
Low Noise Amplifier GPS97121253
• The low noise amplifier 86010142 is designed for the use inside vehicles with train antennas with GPS.
• It includes a preselection filter to prevent the inter ference in case of simultaneous operation at the frequency range 380–960 / 1710–3800 MHz and GPS.
• The product fulfils the requirements according to EN 50155.
Block Diagram
InputTCN female
OutputN female
bias-Tbandpassfilter GPS
bandpassfilter GPS
bandpassfilter GPS
amplifier amplifierlowpass
Type No. 97121253
Frequency MHz 1575.42, L1-signalGain dB 25 ±2Noise figure dB < 2.0VSWR (input, output) < 1.8Operation voltage V 3.3 ... 5.5, ripple < 50 mV,
supplied at inner conductor RF-outputOperation current mA ≤ 25Connector input TNC femaleConnector output N femaleDimensions (w x h x l)
mminches
70 x 22 x 502.8 x 0.9 x 2.0
Mounting mminches
4 holes, 4.5 diameter4 holes, 0.2 diameter
Additional features:• The maximum input power at the input of the amplifier at the frequency
range 380–960 MHz and 1710–3800 MHz is limited to +25 dBm.• The noise level at the GPS-frequency generated by the operation at the
frequency range 380–960 MHz and 1710–3800 MHz should not exceed the thermal noise level at the input of the GPS Amplifier, otherwise the noise figure will be increased.
Environmental conditions:Temperature range: −25 °C … +55 °C (data as specified)
−40 °C … +85 °C (extended range) *)
Please note:It is necessary to use four fixing screws to mount the LNA in case the installation height is more than 2 m.The system operator (receiver) needs to secure a current limit of < 1000 mA.
EU-RED:Hereby, KATHREIN SE declares that the radio equipment type 86010142 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.kathrein.com
*) Extended range of operation: Within an extended temperature range of −40 °C … +85 °C and an extended supplied voltage range of 3.0 V … 6.0 V operation is possible with the following restrictions: Noise figure: < 2.5 dB Gain: > 20 dB
85
Acce
ssor
ies
Product Lineof Mounting Parts
Type WindloadClassification Pole Diameter in mm Type No. Remark
Clamp light / medium ∅ 28 – 60 731651light / medium / heavy ∅ 42 – 115 738546
light / medium / heavy∅ 110 – 220 85010002∅ 210 – 380 85010003
Clamp XM (X-medium) ∅ 55 – 115 85010111
XH (X-heavy) ∅ 55 – 115 85010096
XH (X-heavy) ∅ 110 – 220 85010097
XH (X-heavy) ∅ 210 – 380 85010101Downtilt kit light 732327
light / medium 737978
heavy 85010008
Downtilt kitXM (X-medium) 85010110
XH (X-heavy) 85010099
Azimuth Adjustment Kitlight / medium 85010014 Pole mounting
adjustment angle ±30° (additional clamp
needed)heavy 85010015
Azimuth Adjustment Kit
light / medium 85010016 Wall mounting adjustment angle ±30°
Azimuth Adjustment Kit
X-heavy 85010098
3 Sector Clamp
light / medium
∅ 88.9 742263∅ 88.9 742317∅ 114.3 742033∅ 139.7 742034
heavy∅ 114.3 85010058∅ 139.7 85010059
X-heavy ∅ 114.3 85010102Offset light / medium 85010060 Clearance between
pole and antenna (additional clamp
needed)heavy 85010061
X-heavy 850101042x Panel Mounting Kit
light / mediummax. Panel width 160 742113
Additional clamp neededmax. Panel width 325
85010075heavy 85010076
X-heavy∅ 110 – 220 max. Panel
width 37885010103
∅ 210 – 380 85010108Tension Band
light
∅ 34 – 60 734360
Please note: Only usable
without downtilt kit
∅ 60 – 80 734361∅ 80 – 100 734362∅ 100 – 120 734363∅ 120 – 140 734364∅ 45 – 125 734365
New or changed product
GF
Mounting support clamp
3 sector clamp
86
Type No. 738908
For masts of 94–125 mm diameter
Antenna
Mast
a
b
b
a
Side-mounting ClampOmnidirectional AntennasLarge Pipe
87
Acce
ssor
ies
Side-mounting BracketOmnidirectional Antennas
800/900 MHz (holes 1 and 3) UMTS (hole 2)
Side-mounting is possible for four fixed distances between the tubular mast and the antenna:
A
∅ D
AA
Bracket
Antenna
Bracket
Mast
Antenna base
A A
D D D DHole 2 Hole 3Hole 1Hole 3
AA
Bracket
Antenna
Bracket
Mast
Antenna base
A A
D D D DHole 2 Hole 3Hole 1Hole 3
AA
Bracket
Antenna
Bracket
Mast
Antenna base
A A
D D D DHole 2 Hole 3Hole 1Hole 3
AA
Bracket
Antenna
Bracket
Mast
Antenna base
A A
D D D DHole 2 Hole 3Hole 1Hole 3
A = 100 mm = 0.3 λ A = 160 mm = 0.5 λ A = 240 mm = 0.75 λ A = 80 mm = 0.5 λ
Pipe D
HorizonalRadiation Pattern
SpacingA
Curve
40 mm
direction from mastto antenna
100 mm
160 mm
240 mm
3
0
dB
Pipe D
HorizonalRadiation Pattern
SpacingA
Curve
100 mm
direction from mastto antenna
100 mm
160 mm
240 mm
3
0
dB
Pipe D
Curve
HorizonalRadiation Pattern
SpacingA
40 mm
direction from mastto antenna
80 mm
100 mm3
0
dB
Type No. 737398Side-mounted bracket(for mast diameters of 40–105 mm)
Type No. 737398
Fits for antennatype no.
800/900 MHz736347738192
88
RCU with RFID Feature• External RCU 86010148V01 includes a RFID reader• Antenna spindles are equipped with RFID tags• The antenna specific data is stored on this tag: a Type number a Serial number a Configuration File
• With power on, the data is read out automatically from the tag by the RCU
• List of all updated antennas on our homepage: www.kathrein.com/rfidspindle
FlexRET• Integrated RET module inside the antenna (86010153V01)• Pre-configured with the antenna specific parameters: a Type number a Serial number a Configuration file
• Calibrated ex-factory• The FlexRET module is exchangeable a Automatic data transfer in case of exchange with
internal RFID taga Only calibration is neccessary
• Daisy chain possibility with FlexRET antennas and / or external RCUs
• Same module for all antennas• SingleRET or MultiRET selection possible• Array allocation possible with special Site Sharing Adapter
or Gender Adapter / Port Extender
Site Sharing Adapter• Needed whenever the AISG control of a FlexRET antenna
shall be performed by a higher number of base stations (BTS)
• 2 different realizations available a 3-way Site Sharing Adapter: Type no. 86010154 –
FlexRET control with up to 3 BTS a 6-way Site Sharing Adapter: Type no. 86010155 – FlexRET
control with up to 6 BTS• Daisy chaining of up to 3 FlexRET antennas• Additional ALDs can be mounted prior to the Site Sharing
Adapter• Flexible allocation of antenna arrays to the different BTS
units using a special software application via PC• Each BTS can act independently• Individual password protection of configuration possible• Configuration can be sent to the Site Sharing Adapter with
every AISG control device (BTS or e.g. Kathrein ALC)
Kathrein’s Remote Electrical Tilt System
Functionality of Different RET Technologies
BTS or Operator A
BTS or Operator B
BTS or Operator C
3 x AISG in1 x FlexRET out
86010154
89
Acce
ssor
ies
Kathrein’s Remote Electrical Tilt System
Functionality of Different RET Technologies
Manuals for all our AISG control devices and for the Site Sharing Adapter as well as the corresponding software downloads can be found on our homepage in the section “Technical Documents” respectively “Driver and Software”.
For details of the RET system please also see Kathrein’s RET brochure.
Kathrein’s overall RET system works in accordance with the AISG (Antenna Interface Standards Group) standard and 3GPP (3rd Generation Part ner ship Project).
MOBILECOMMUNICATION
Remote Electrical Tilt SystemOverview of Products, Installation, Control Possibilities and FAQs
Gender Adapter (86010162)• Can be used if 2 base stations (BTS) are interconnected to
one common FlexRET antenna• Mounted on the FlexRET output of the module• Converts the AISG output to an AISG input• The allocation of the antenna arrays can easily be
performed during the commissioning process via the BTS
Port Extender (86010163)• Can be used if 2 BTS are interconnected to common
FlexRET antennas in daisy chain• Mounted on the FlexRET module by 2 screws• Converts 1 FlexRET input and output to 2 FlexRET inputs and
outputs• Daisy chaining with further FlexRET antennas and / or
external RCUs• The allocation of the antenna arrays can easily be
performed during the commissioning process via the BTS
90
91
9980
0001
14/0
/081
8/PP
E/pd
f | Te
chnic
al da
ta su
bject
to ch
ange
.
Title:
iSto
ck.co
m |
Blue
_Cut
ler, G
BPer
kins;
Foto
lia.co
m |
Tyler
Olso
n
KATHREIN Special Communications GmbHGnigler Straße 565020 Salzburg, AustriaPhone +43 662 875531-14www.kathrein.com | info@kathrein-special-com.at