CHINA INSPECTION SERVICE CO.,LTDsamplereport.china-inspection-service.com/China-Pre...4. Workmanship...

transcript

CHINA INSPECTION SERVICE CO.,LTD

www.China-Inspection-Service.com CIS, your reliable partner in China!

FAX: +86 755 6164 0839 info@China-Inspection-Service.com Page 1 of 39

Pre-Shipment Inspection Report

General Information:

Report Number: PSI-CIS1807xxxxxx

Product name: Baby blankets in four designs

Item #: Please see part 1 PO# N/A Ordered quantity: 2000 pieces Client name: xxxxxx Supplier name: xxxxx Inspection Date: July 16, 2018 Departure time to the

factory:

7:00AM

Arrival time: 9:00AM Departure time: 14:00PM Inspection location: Xiaoshan, Hangzhou, Zhejiang, China.

Inspection summary:

Inspection Sections Conform?

(Y / N/ PENDING)

Remarks

1. Product quantity Y

2. Packing PENDING Please see CIS comments # 1.

3. Product conformity PENDING Please see CIS comments # 2.

4. Workmanship appearance / function N Beyond AQL

5. Reliability/function tests N See 5.1

6. Measurements Y

Conclusion: FAILED FOR PART 4 AND 5.

CIS comments: 1. Found the polybags were confusion in the cartons, and clapboard was missing for all cartons. SAMPLE

REPORT

2. For all inspection products, found the main label’s location was confusion.

Manufacturer Signature: Lia Chen CIS signature: Wang Xufeng

SAMPLE R

1. Product quantity inspection:

Model # Model Name Ordered

Available

% of Finished

Products

Cartons

Ordered

Packed

Cartons

% of Finished

Packing

N/A Blue square desig 500 472 94.4% 10 9 90%

N/A Pink square design 500 491 98.2% 10 9 90%

N/A Blue design 500 500 100% 10 10 100%

N/A Pink design 500 496 99.2% 10 9 90%

2. Packing inspection:

Test # Spec Requirement Conform? (Y / N/ PENDING)

Remarks

2.1 Packing method checking PENDING 50 pieces packed per export carton.

No information from client.

2.2 Shipping mark checking N/A For all cartons, the shipping mark was missing

2.3 Carton dimension checking (measured

data should match with the shipping

mark, error should be within 土 1.5cm)

PENDING No information show on shipping mark.

2.4 G.W. checking(measured data should

match with the shipping mark, error

should be within 土 1kg)

PENDING No information show on shipping mark.

2.5 Carton material checking Y Please see the picture below

2.6 Carton bar code label checking N/A

2.7 Product Manual (included in packing?) N/A

2.8 Warranty card (included in packing?) Y

SAMPLE R

Pictures:

Packed products Packed products

Carton view Carton view

SAMPLE R

Carton weight check Carton weight check:17.1kg

Carton length Carton length：50cm

Carton width Carton width:41cm

SAMPLE R

Carton height Carton height:42cm

Open the carton Carton material - 5layers

50polybags in the carton Packing detail view

SAMPLE R

Packing detail view Packing detail view

SAMPLE R

Packing detail view Polybag length

Polybag length:40cm Polybag width

Polybag width:29cm Packing detail view

SAMPLE R

Color paper on the product Barcode view

SAMPLE R

Belt length Belt length:93cm

Belt width:2.6cm Packing detail view

SAMPLE R

Packing detail view The barcode on the product

SAMPLE R

Packing detail view The barcode on the product

3. Product conformity inspection:

Test # Testing Items Conform?

(Y / N/ PENDING)

Remarks

3.1 Product style Y

3.2 Product color Y

3.3 Compared with sample which

provide by factory

3.4 Product bar code checking Y

3.5 Country origin information found Y “Made in china” on the color paper

3.6 Logo check

-should be on all the blankets

3.7 Inserts check

-should be on all the blankets

3.8 Sew lines must be straight Y

3.9 All products should not with Y

SAMPLE R

connecting stitches

Sample (Information photos) Product

SAMPLE R

Pictures:

Product detail view Product detail view

SAMPLE R

Product main label view Product main label view

SAMPLE R

Product main label view

SAMPLE R

4. Workmanship appearance / function inspection

Inspection Method Applied:

Inspection Standard: ANSI/ASQZ1.4 (MIL-STD-105E) Sampling plan: Single, normal Inspection level: G-II for workmanship/function checking; S-II for reliability tests AQL (Accepted Quality Level): Less than 1.5%. Special inspection points required by the client:

✓ All products should not with connecting stitches. ✓ Shouldn't be any stains on the blankets. ✓ Shouldn't be any damage from any side. Model # Sample size

(Major defects) Sample size

(Minor defects)

Cartons

Quantity Selected Carton #

4 colors products 125 125 8 No carton number

Total: 125 125 8

# Defect description Cri. Maj. Min.

1. Pucker at side 0 0 4 2. Dirty mark 0 2 18 3. Fabric edge/ Missing print 0 3 0 4. Open seam 0 1 0 5. Pucker + thread ends 0 1 0 6. Thread ends 0 0 6 7. Fabric defect 0 3 0 8. Crease mark on surface 0 0 8 9. Unfaudio-videooring at edge 0 1 0 10. Broken carton 0 1 0

Total defects: 0 12 36

Maximum allowed defects: 0 7 10

SAMPLE R

CONCLUSION: Beyond AQL

Pictures:

Pucker at side - Minor Pucker at side - Minor

Pucker at side -Minor Pucker at side - Minor

Dirty mark - Major Dirty mark - Major

SAMPLE R

Dirty mark - Minor Dirty mark - Minor

SAMPLE R

Fabric edge/ Missing print - Major Fabric edge/ Missing print - Major

Fabric edge/ Missing print - Major Open seam - Major

Pucker + thread ends - Major Thread ends - Minor

SAMPLE R

Thread ends - Minor Thread ends - Minor

Thread ends - Minor Fabric defect - Major

SAMPLE R

Fabric defect - Major Fabric defect - Major

Crease mark on surface - Minor Crease mark on surface - Minor

SAMPLE R

Crease mark on surface - Minor Crease mark on surface - Minor

Unfaudio-videooring at edge - Major Broken carton - Major

SAMPLE R

5. Reliability & Function tests

# Testing Items Sample Size PASS/FAIL Defect Description

5.1 Carton Drop test:

1 corner / 3 edges / 6 sides

1carton/style FAIL Found broken mark on export carton.

5.2 Bar code reading check 5pcs/style PASS

5.3 Tape test on silk screen

printed logos/text

5pcs/style PASS

5.4 Metal detect test: no metal

parts such as broken stitches

found inside the products

All samples N/A The Metal test machine was missing in

the factory.

5.5 Color shading check 20pcs/style PASS

5.6 Color fastness test ( fabric/

2pcs/style PASS

5.7 Pull test of sewn 2pcs/style PASS

Pictures:

Carton Drop test Carton Drop test

SAMPLE R

Tape test Tape test

Color fastness test Color fastness test

SAMPLE R

Color shading check Color shading check

Barcode scan test Barcode scan test

Needle Damage test Needle Damage test

SAMPLE R

6. Measurements Data sheet:

Testing items Spec. Sample #

1 2 3 4 5

6.1 Size of product: L*W cm

Blue square design 100x75 101.5x76.5 101.5x76 101x75.5 101x75.5 101.5x76

Pink square design 100x75 101.5x76 101.5x76.5 101.5x76 101x76 101x75.5

Blue design 100x75 101x75.5 101x75.5 101.5x76.5 101.5x76.5 101x76

Pink design 100x75 101x76 100.5x75.5 101x76 101.5x76 101.5x76.5

6.2 Weight of product: g

Blue square desig N/A 300 310 300 300 310

Pink square design N/A 310 310 310 300 300

Blue design N/A 300 310 310 300 300

Pink design N/A 310 300 300 310 310

Pictures:

Product size check Product size check

SAMPLE R

Product size check Product size check

Product weight check Product weight check

SAMPLE R

Product weight check Product weight check

Other related pictures:

Factory gate Factory building

SAMPLE R

**********END OF THE REPORT********

This document is neither a green light for shipment nor an inspection certificate. The final result of the inspection and authorization to ship the orders MUST be confirmed by the party entrusting CIS for the

inspection. The above result(s) reflect(s) CIS Limited’s findings at the time and place of inspection. This report does not release the buyer or seller from contractual responsibilities, nor does it prejudice the buyer’s right of claim toward the seller/supplier for compensation for any apparent and/or hidden defects not detected

during inspection or occurring anytime thereafter.

SAMPLE R

CHINA INSPECTION SERVICE CO.,LTDsamplereport.china-inspection-service.com/China-Pre...4. Workmanship...

Documents