Post on 19-Jan-2016
transcript
A Swagelok ® Company
Sta in less Stee lComponents for theLiquid F low Indust r ies
www.swagelok.comwww.jensenfittings.com
Sanitary Kwik-Clamp Fittings.............................................. ....................................................1Sanitary Kwik-Clamp Elbows.............................................. ....................................................2Sanitary Kwik-Clamp Tees.................................................. ....................................................3Sanitary Kwik-Clamp Crosses, Clamps & Gaskets ............ ....................................................4Sanitary Kwik-Clamp Ferrules & Adapters ......................... ....................................................8Kwik-Clamp Adapters ......................................................... ....................................................10Sanitary Kwik-Clamp Adapter Reducers ............................ ....................................................12Sanitary Kwik-Clamp Lateral & True Y ............................... ....................................................14
Industrial Kwik-Clamp Fittings ............................................ ....................................................15Industrial Kwik-Clamp Elbows, Tees................................... ....................................................16Industrial Kwik-Clamp Adapters & Reducers...................... ....................................................17
Sanitary Butt Weld Fittings ................................................. ....................................................19Sanitary Butt Weld Fittings General Specifications & Data ......................................................... ....................................................20
Bio-Pharm Fittings .............................................................. ....................................................27Bio-Pharm Fittings Specifications....................................... ....................................................28Swagelok TS Fittings .......................................................... ....................................................30Bio-Pharm Automatic Weld Fittings .................................... ....................................................33Bio-Pharm Kwik-Clamp Fittings.......................................... ....................................................40
Sanitary Acme Threaded Fittings ....................................... ....................................................45Sanitary Acme Threaded Fittings General Specifications & Data ......................................................... ....................................................46Tube
O.D. Butt Weld Fittings (Unpolished).................................. ....................................................59 O.D. Butt Weld Fittings General Specifications & Data...... ....................................................60
Miscellaneous Flow Components....................................... ....................................................65Manual Butterfly Valves....................................................... ....................................................66Air-Actuated Butterfly Valves .............................................. ....................................................67Vertical Disk Check Valves ................................................. ....................................................68Ball Check Valves ............................................................... ....................................................69Compression and Relief Valves.......................................... ....................................................70Sanitary Ball Valves ............................................................ ....................................................71Hangers .............................................................................. ....................................................73Inline Strainer and Filter Specifications and Data .............. ....................................................74Sightglass Specifications (JCD54) ..................................... ....................................................76Sightglass Specifications (#162S & #162) ......................... ....................................................78Jensafe ............................................................................... ....................................................79Weld In Sightglass .............................................................. ....................................................80Lateral and True Y .............................................................. ....................................................80Flow Plate ........................................................................... ....................................................81Sanitary Flange to Swagelok Tube Fitting.......................... ....................................................81Interlock Fittings.................................................................. ....................................................82John Perry Fittings.............................................................. ....................................................84APV-K-Clamp...................................................................... ....................................................85APV-PV Threaded .............................................................. ....................................................87Specials .............................................................................. ....................................................913A ....................................................................................... ....................................................95ISO...................................................................................... ....................................................96
Table of Contents
Heat TreatmentDuring bending and other forming processes, stress can develop. Jensenheat treats all of these products with our own vacuum annealing furnace.This process minimizes stress corrosion cracking and provides extraprotection for fluid products using Jensen fittings.
ISO RegisteredJensen is an ISO 9002 Registered Company. This international qualitymanagement system is designed to establish quality standards and ensurethey are met. This process is monitored with external and internal audits toassure continuous improvement. (Jensen is also a 3A Member company.)
SQC - Statistical Quality ControlJensen uses SQC extensively in conjunction with our ongoing QualityProgram. Fittings are inspected using SQC to monitor tolerances, angularity,squareness, ovality and polish finishes to meet or exceed industry standards
•
Jensen . . .Quality Products Since 1959
•
•
PackagingAll Jensen fittings are properly packaged and labeled with a full description.This bar code system ensures correct shipping procedures and productidentification.
Heat TraceabilityAll applicable 316L fittings are identified with heat numbers. Fittings madewith more than one component will carry multiple heat numbers (i.e. areducing tee). Material Test Reports (MTR's) are also available to documentall heat numbers. At the time of order, please specify if heat numbers andMTR's are required.
Cap & Bag PackagingAll AWF/TL fittings, when applicable, will be shipped, capped, bagged andlabeled. The label will show our part number, description and heat numbers.
•
•
•
Prefix:JC = Jensen Kwik-ClampJ = Jensen Sanitary Butt Weld, Tube OD and Non Kwik-Clamp Gaskets
(ie, APV or APV Fittings)JTL = Jensen Extended Tangent (BPE Fittings)Number = Acme Threaded or Industrial Kwik-Clamp
Part Number Guide
2= Elbow7= Tee9= Cross
12= Union13= Fastener14= Ferrule (KC, Plain
Bevel Seat, APC orAPV)
15= Ferrule (ACME, APC)16= End Cap17= Tube Section18= Female NPT
19= Male NPT21= Any Connection x
Male NPT22= Any Connection x
Female NPT23= Thermometer Cap24= Hanger25= Wrench26= BW x Female NPT28= Lateral or True Y30= Sample Valve31= Concentric Reducer
32= Eccentric Reducer38= Flanges40= Gaskets45= Check Valve54= Sightglass60= Relief or Compression
Valve80= Orifice Plate
160= Divert or Shut-OffValve
162= Sightglass181= Male Camlock
X= ShortS= Standard
AM7= American StandardEX= Expanding
(Roll-On)
R= Roll-On (Bevel SeatFerrules only) orReducing (tees only)
W= WeldM= Tri-Clamp or
Kwik-Clamp
T= ThreadedC= ThreadedF= Plain FerruleK= 45 Degree
4= 3046= 316L
Suffix:
Middle:
1= Unpolished ID and OD3= Polished ID (32 Ra
and Unpolished OD)5= Polished OD (32 Ra)
and Unpolished ID7= Polished ID (32 Ra) and
Polished OD (32 Ra)
3PC= Polished ID (20 Ra)and Unpolished OD
7PL= Polished ID (20 Ra) andPolished OD (32 Ra)
3PD= Polished ID (15 Rawith electropolish) andUnpolished OD
7PM=Polished ID (15 Ra withelectropolish) andPolished OD (32 Ra)
Ra= Rough Average
Polish Code:
Material:
1/8 in.=181/4 in.=253/8 in.=381/2 in.=505/8 in.=583/4 in.=75
1 in.=101-1/4 in.=1251-1/2 in.=15
2 in.=202-1/2 in.=25
3 in.=30
4 in.=406 in.=608 in.=80
10 in.=10012 in.=120
Size:
This guide is designed to help explain how to properly put together Jensen part numbers for thepurpose of quoting, ordering and referencing. We will be referring to the section and color codesfrom the Jensen/Swagelok catalog number MS-02-150.
Section:Sanitary Kwik-Clamp Fittings (pages 1-14)All part numbers in this section will begin with a “JC” which represents Jensen Clamp. Thesurface finish for all of the products in this section will be 32 Ra ID and 32 Ra OD. Based uponthis, we will not include the polish code into the part number. The full part number consists of theitem code, material grade (304/316L) and size. If there are two sizes, such as for a reducer or anadapter, both sizes are listed.
Example:
JC2 4 20
Item Code Material Grade Size(4=304, 6=316L)
Section:Industrial Kwik-Clamp Fittings (pages 15-17)These fittings are dimensionally the same as the fittings in the Sanitary Kwik-Clamp section. Thedifference is that these fittings have either a polished or unpolished ID or OD. One of three polishcodes must be specified:
Polish Code 1 - unpolished ID and unpolished OD
Polish Code 3 - 32 Ra ID and unpolished OD
Polish Code 5 - unpolished ID and 32 Ra polished OD
The full part number will consist of the item code, material grade (304/316L), polish and the size.
Example:
2CLMO 4 1 15
Item Code Material Grade Polish Code Size(4=304, 6=316L) (1,3,5)
Section:Sanitary Butt Weld Fittings (pages 19-26)All part numbers in this section will begin with a “J” which represents Jensen weld. The surfacefinish for all of the products in this section will be:
Polish Code 1 - unpolished ID and unpolished OD
Polish Code 3 - 32 Ra ID and unpolished OD
Polish Code 5 - unpolished ID and 32 Ra polished OD
Polish Code 7 - 32 Ra ID and 32 Ra OD
Based upon this, we will include the polish code into the part number. The full part number con-sists of the item code, material grade (304/316L), polish and the size. If there are two sizes, suchas for a reducer or an adapter, both sizes are listed.
Example: J2S 4 7 20
Item Code Material Grade Polish Code Size(4=304, 6=316L) (1,3,5,7)
Section:Bio-Pharm Fittings (pages 27-44)Jensen’s Bio-Pharm product is produced in four surface finishes. You must specify the polish codein the part number.
Polish Code 3PC - 20 Ra ID polished, unpolished OD
Polish Code 7PL - 20 Ra ID polished, 32 Ra OD polished
Polish Code 3PD - 15 Ra ID polished and electropolished, unpolished OD
Polish Code 7PM - 15 Ra ID polished and electropolished, 32 Ra OD polished
The full part number will consist of the item code, material grade (316L only), polish code and size.
Example:JTL7W 6 7PL 30
Item Code Material Grade Polish Code Size(6=316L only) (3PC, 7PL, 3PD, 7PM)
NOTE: The only exception to the above are the JTL14AM7 ferrules. These part numbers will con-sist of the item code, material (316L only), polish code (PL or PM) and size.
Example:JTL14AM7 6 PL 15
Item Code Material Grade Polish Code Size(6=316L only) (PL,PM)
Section:Sanitary Acme Threaded Fittings (pages 45-58)The surface finish for all of the products in this sectin will be 32 Ra ID and 32 Ra OD. The full partnumber consists of the item code, material grade (304/316L) and size. If there are two sizes, suchas for a reducer or an adapter, both sizes are listed.
Example:
14WF 4 40
Item Code Material Grade Size(4=304, 6=316L)
Section:Tube OD Unpolished Butt Weld Fittings (pages 59-64)All part numbers in this section are unpolished ID and OD. The polish code for all items in thissection will be:
Polish Code 1 - unpolished ID and unpolished OD
The full part number will consist of the item code, material grade (316L only), polish code andsize. Based upon this, we will include the polish code in the part number. The full part numberconsists of the item code, material grade (304/316L), polish and size. If there are two sizes, suchas for a reducer or an adapter, both sizes are listed.
Example:
J31W 4 1 2015
Item Code Material Grade Polish Code Size(4=304, 6=316L) (1)
Example:
J19W 4 20
Item Code Material Grade Size(4=304, 6=316L)
Exceptions: J19W, J38W, 26EF, J16W
These items are completely machined and are only available with a 32 Ra, ID/32 Ra OD.
Section:Miscellaneous Flow Components (pages 65-90)The surface finish for all of the products in this section will be 32 Ra ID and 32 Ra OD. Basedupon this, we will not include the polish codes in any of the part numbers. This section offers quitea variety of sightglasses, fittings and strainers. We will look at each group of products individually.
Hangers: J24FCF 15 J24PVC 25
Item Code Size Item Code Size
NOTE: These are available in 304 only. We do not include the material grade in these part numbers.
Strainers: SM1 6 20
Item Code Material Grade Size(6=316L only)
Sightglasses:JCD54 6 20
Item Code Material Grade Size(4=304, 6=316L)
Interlock Fittings:14WI 6 15
Item Code Material Grade Size(4=304, 6=316L)
John Perry Fittings:15WFF 4 20
Item Code Material Grade Size(4=304, 6=316L)
APV K-Clamp:JA14X 4 30
Item Code Material Grade Size(4=304, 6=316L)
PV Threaded:2CPV 6 40
Item Code Material Grade Size(4=304, 6=316L)
A Swagelok Company
Sanitary
Kwik-Clamp
Fittings
1
SANITARY
KWIK
CLAMP
FITTINGS
2
JC2 – 90˚ ELL
Stainless Steel Hex Nut 304 only.
JC215 – 90˚ SWEEP ELL
A
A
R
A
B
B
A
B
A
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
223⁄431⁄241⁄4565⁄8101⁄2
50.869.988.9
108.0127.0168.3266.7
11⁄221⁄4333⁄441⁄269
38.157.276.295.3
114.3152.4228.6
0.350.440.811.002.003.66
12.10
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC214 – 90˚ SWEEP ELL
111⁄2221⁄234
25.438.150.863.576.2
101.6
23⁄16
231⁄32
323⁄32
419⁄32
513⁄32
77⁄32
55.675.494.4
116.7137.3183.3
223⁄431⁄241⁄4565⁄8
50.869.988.9
108.0127.0168.3
0.601.191.943.134.758.65
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
23⁄16
231⁄32
323⁄32
419⁄32
513⁄32
77⁄32
55.675.494.4
116.7137.3183.3
223⁄431⁄241⁄4565⁄8
50.869.988.9
108.0127.0168.3
0.390.691.061.592.755.06
JC2-J31 – 90˚ REDUCING ELL, NON-TAPEREDSIZE A B APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
2223⁄4223⁄431⁄2223⁄431⁄241⁄4223⁄431⁄241⁄451⁄8
50.850.869.950.869.988.950.869.988.9
108.050.869.988.9
108.0130.2
2223⁄4223⁄431⁄2223⁄431⁄241⁄4223⁄431⁄241⁄45
50.850.869.950.869.988.950.869.988.9
108.050.869.988.9
108.0127.0
0.380.740.951.101.401.581.952.151.822.382.302.502.904.004.75
Sanitary fittings meet the geometry of ISO 2852.
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC2K – 45˚ ELL
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
11⁄817⁄16
13⁄421⁄16
23⁄831⁄841⁄2
28.636.544.552.460.379.4
114.3
11⁄221⁄4333⁄441⁄269
38.157.276.295.3
114.3152.4228.6
0.240.310.500.571.192.257.80
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC7 – TEE
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
23⁄823⁄431⁄231⁄233⁄441⁄253⁄4
60.369.988.988.995.3
114.3146.1
43⁄451⁄27771⁄29111⁄2
120.7139.7177.8177.8190.5228.6292.1
0.380.691.381.592.503.88
12.20
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC7S – SHORT OUTLET TEE
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
23⁄823⁄431⁄231⁄233⁄441⁄253⁄4
60.369.988.988.995.3
114.3146.1
11⁄813⁄815⁄817⁄821⁄823⁄427⁄8
28.634.941.347.654.069.973.0
0.330.631.351.502.453.80
11.90
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
JC7R – REDUCING TEE (Reduced Size on Branch)
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 16 x 11⁄26 x 26 x 21⁄26 x 36 x 4
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 25.4152.4 x 38.1152.4 x 50.8152.4 x 63.5152.4 x 76.2152.4 x101.6
23⁄421⁄8213⁄32
23⁄8221⁄32
213⁄16
23⁄8229⁄32
31⁄16
33⁄32
31⁄8313⁄32
39⁄16
319⁄32
319⁄32
51⁄251⁄251⁄251⁄251⁄451⁄2
69.954.061.160.367.571.460.373.877.878.679.486.590.591.391.3
139.7139.7139.7139.7133.4139.7
25⁄32
29⁄16
29⁄16
227⁄32
227⁄32
227⁄32
33⁄32
33⁄32
33⁄32
33⁄32
41⁄16
41⁄16
41⁄16
41⁄16
41⁄16
53⁄453⁄453⁄453⁄453⁄453⁄4
54.865.165.172.272.272.278.678.678.678.6
103.2103.2103.2103.2103.2146.1146.1146.1146.1146.1146.1
45⁄16
51⁄851⁄8511⁄16
511⁄16
511⁄16
63⁄16
63⁄16
63⁄16
63⁄16
81⁄881⁄881⁄881⁄881⁄8111⁄2111⁄2111⁄2111⁄2111⁄2111⁄2
109.5130.2130.2144.5144.5144.5157.1157.1157.1157.1206.4206.4206.4206.4206.4292.1292.1292.1292.1292.1292.1
1.251.351.381.651.651.592.752.802.502.503.363.253.363.313.677.407.507.607.667.757.86
3
SANITARY
KWIK
CLAMP
FITTINGS
R
A
A
A
A
B
A A
B
B
A
C
4
SANITARY
KWIK
CLAMP
FITTINGS
A
B
A
AB
A B
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC7RS – SHORT OUTLET REDUCED TEE
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 16 x 11⁄26 x 26 x 21⁄26 x 36 x 4
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 25.4152.4 x 38.1152.4 x 50.8152.4 x 63.5152.4 x 76.2152.4 x101.6
25⁄32
29⁄16
29⁄16
227⁄32
227⁄32
227⁄32
33⁄32
33⁄32
33⁄32
33⁄32
41⁄16
41⁄16
41⁄16
41⁄16
41⁄16
53⁄453⁄453⁄453⁄453⁄453⁄4
54.865.165.172.272.272.278.678.678.678.6
103.2103.2103.2103.2103.2146.1146.1146.1146.1146.1146.1
13⁄815⁄815⁄817⁄817⁄817⁄821⁄821⁄821⁄821⁄825⁄825⁄825⁄825⁄825⁄835⁄835⁄835⁄835⁄835⁄833⁄4
34.941.341.347.647.647.654.054.054.054.066.766.766.766.766.792.192.192.192.192.195.3
1.251.351.381.651.651.592.752.802.502.503.363.253.363.313.677.407.507.607.667.757.86
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC9 – CROSS
1⁄23⁄4111⁄2221⁄234
12.719.125.438.150.863.576.2
101.6
25⁄825⁄823⁄823⁄431⁄231⁄233⁄441⁄2
66.766.760.369.988.988.995.3
114.3
51⁄451⁄443⁄451⁄27771⁄29
133.4133.4120.7139.7177.8177.8190.5228.6
0.440.440.560.881.571.782.794.14
5
SANITARY
KWIK
CLAMP
FITTINGS
BC
A D
AJC13HC – SINGLE PIN HEAVY DUTY CLAMPJC13HD – HEAVY DUTY CLAMPJC13HDR – ROUND HEAVY DUTY CLAMP
JC13HD JC13HDRAJC13HC
SIZE A B C D APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
JC9R – REDUCING CROSS
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 16 x 11⁄26 x 26 x 21⁄26 x 36 x 4
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 25.4152.4 x 38.1152.4 x 50.8152.4 x 63.5152.4 x 76.2152.4 x 101.6
25⁄32
29⁄16
29⁄16
227⁄32
227⁄32
227⁄32
33⁄32
33⁄32
33⁄32
33⁄32
41⁄16
41⁄16
41⁄16
41⁄16
41⁄16
53⁄453⁄453⁄453⁄453⁄453⁄4
54.865.165.172.272.272.278.678.678.678.6
103.2103.2103.2103.2103.2146.1146.1146.1146.1146.1146.1
23⁄421⁄8213⁄32
23⁄8221⁄32
213⁄16
23⁄8229⁄32
31⁄16
33⁄32
31⁄8313⁄32
39⁄16
319⁄32
319⁄32
51⁄251⁄251⁄251⁄251⁄451⁄2
69.954.061.160.367.571.460.373.877.878.679.486.590.591.391.3
139.7139.7139.7139.7133.4139.7
45⁄16
51⁄851⁄8511⁄16
511⁄16
511⁄16
63⁄16
63⁄16
63⁄16
63⁄16
81⁄881⁄881⁄881⁄881⁄8111⁄2111⁄2111⁄2111⁄2111⁄2111⁄2
109.5130.2130.2144.4144.4144.4157.1157.1157.1157.1206.4206.4206.4206.4206.4292.1292.1292.1292.1292.1292.1
51⁄241⁄4413⁄16
43⁄455⁄16
55⁄843⁄4513⁄16
61⁄863⁄16
61⁄4613⁄16
71⁄873⁄16
73⁄16
11111111101⁄211
139.7108.0122.2120.7134.9142.9120.7147.6155.6157.1158.8173.0181.0182.5182.5279.4279.4279.4279.4266.7279.4
0.901.701.703.453.452.003.653.623.103.124.204.064.204.144.598.108.208.258.559.579.83
SIZE A APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm
11⁄2221⁄2346
38.150.863.576.2
101.6152.4
2.1222.6543.1853.7174.8206.695
53.967.480.994.4
122.4170.1
9.611.213.614.818.826.0
A
6
AJC13HS – THREE SECTION CLAMP
SANITARY
KWIK
CLAMP
FITTINGS
SIZE A APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm
11⁄2221⁄234
38.150.863.576.2
101.6
2.1222.6543.1853.7174.820
53.967.480.994.4
122.4
0.860.931.051.311.70
AJC13HP – HIGH PRESSURE CLAMPSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
11⁄2221⁄234
38.150.863.576.2
101.6
2.0462.5783.1103.6404.744
52.065.579.092.5
120.5
22.028.032.038.044.0
JC13HD – 3/4” CLAMP
SIZE INCHES MILLIMETERS
A 1.125 28.6A
GASKETS
Jensen Kwik-Clamp Gaskets
Standard-Molded, one piece O-Ring gasket
JC40N BUNA-N RUBBERJC40T WHITE TEFLONJC40S SILICONEJC40V VITONJC40E EPDM
* One size accommodates 1⁄2" & 3⁄4" fittings.* Weight approximately 6 ounces.
7
SANITARY
KWIK
CLAMP
FITTINGS
JC13HDR-ROUND HEAVY DUTY CLAMPJC13HD-HEAVY DUTY CLAMP(With wing nut tightened to 25 in.-lb.of torque)
AJC13HC-HEAVY DUTY CLAMP(With wing nut tightened to 25 in.-lb.of torque)
AJC13HP-HIGH PRESSURE CLAMP(With wing nut tightened to 25 ft lb of torque)
Clamps are tested hydrostatically using Standard-Molded Buna-M material gaskets. All ratings shown are dependent uponrelated components in the system, absence of shock pressure,proper expansion of ferrules, assembly of joints, and installation.For temperatures above 250˚F/121.1˚C we recommend onlyAJC13HP clamps be used.
PRESSURE RATINGS psi/Bar
Temperature SIZE TUBE O.D.˚F / ˚C 1⁄2 3⁄4 1 11⁄2 2 21⁄2 3 4 670/21.1 1500/103.4 1500/103.4 500/34.5 500/34.5 450/31.0 400/27.6 350/24.1 200/13.8 150/10.3
250/121.1 1500/103.4 1500/103.4 250/17.2 250/17.2 250/17.2 200/13.8 150/10.3 125/8.6 75/5.2
PRESSURE RATINGS psi/Bar
Temperature SIZE TUBE O.D.˚F / ˚C 1 11⁄2 2 21⁄2 3 470/21.1 500/34.5 500/34.5 450/31.0 400/27.6 350/24.1 200/13.8
250/121.1 250/17.2 250/17.2 250/17.2 200/13.8 150/10.3 125/8.6
PRESSURE RATINGS psi/Bar
Temperature SIZE TUBE O.D.˚F / ˚C 11⁄2 2 21⁄2 470/21.1 1500/103.4 1000/68.9 1000/68.9 1000/68.9
250/121.1 1200/82.7 800/55.1 800/55.1 800/55.1
8
SANITARY
KWIK
CLAMP
FITTINGS
JensenKWIK-CLAMP
GENERAL SPECIFICATIONS AND DATA PAGE
MATERIALS OF CONSTRUCTION AND DESIGN
All fittings available in Stainless Type 304 & 316L. Captive Hexagon Nut as shown is StainlessT304. All one inch fittings take 1-1/2" clamp assemblies. Kwik-Clamps in Type 304 Stainless Steel only.
Heat traceability is available on all 316L fittings, if specified at the time of order. Each 316L fittingwill be marked with its correct heat number.
SIZE A D E APROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
JC14X – SHORT WELDING FERRULE
1⁄23⁄4111⁄2221⁄234681012
12.719.125.438.150.863.576.2
101.6152.4203.2254.0304.8
1⁄21⁄21⁄21⁄21⁄21⁄21⁄25⁄83⁄4111
12.712.712.712.712.712.712.715.919.125.425.425.4
.370
.620
.8701.3701.8702.3702.8703.8345.7827.7609.760
11.732
9.415.722.134.847.560.272.997.4
146.9197.1247.9298.0
0.5000.7501.0001.5002.0002.5003.0004.0006.0008.000
10.00012.000
12.719.125.438.150.863.576.2
101.6152.4203.2254.0304.8
0.040.050.120.090.120.150.180.380.421.254.007.50
SIZE C D E APROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
JC14AM7 – BUTT WELDING FERRULE
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
11⁄811⁄811⁄811⁄811⁄811⁄811⁄2
28.628.628.628.628.628.638.1
0.8701.3701.8702.3702.8703.8345.782
22.134.847.560.272.997.4
146.9
1.0001.5002.0002.5003.0004.0006.000
25.438.150.863.576.2
101.6152.4
0.090.130.200.250.310.561.20
SIZE A D E APROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
JC14H – TANK WELDING FERRULE
111⁄2221⁄234
25.438.150.863.576.2
101.6
15⁄815⁄813⁄413⁄4113⁄16
21⁄8
41.341.344.544.546.054.0
0.8701.3701.8702.3702.8703.834
22.134.847.560.272.997.4
1.1601.6762.1922.7083.2244.256
29.542.655.768.881.9
108.1
0.170.350.691.001.402.50
A
D E
C
D E
A
D E
9
SANITARY
KWIK
CLAMP
FITTINGS
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC14EX – RECESSLESS FERRULE (For Expanding)
11⁄2221⁄234
38.150.863.576.2
101.6
11⁄815⁄16
13⁄817⁄16
11⁄2
28.633.334.936.538.1
11⁄2221⁄234
38.150.863.576.2
101.6
0.130.250.340.470.70
A
B
C
D E
SIZE C D E APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
JC14 – TANK WELDING SPUD (Light)
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
3333446
76.276.276.276.2
101.6101.6152.4
0.8701.3701.8702.3702.8703.8345.782
22.134.847.560.272.997.4
146.9
1.0001.5002.0002.5003.0004.0006.000
25.438.150.863.576.2
101.6152.4
0.160.210.400.540.771.252.32
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC14AHR – RUBBER HOSE ADAPTER ANDREDUCING RUBBER HOSE ADAPTER
1⁄2 x 1⁄81⁄2 x 1⁄41⁄2 x 3⁄81⁄21⁄2 x 5⁄81⁄2 x 3⁄43⁄4 x 1⁄83⁄4 x 1⁄43⁄4 x 3⁄83⁄4 x 1⁄23⁄4 x 5⁄83⁄4111⁄2 x 1⁄811⁄2 x 1⁄411⁄2 x 3⁄811⁄2 x 1⁄211⁄2 x 5⁄811⁄2 x 3⁄411⁄2 x 11⁄411⁄22 x 1⁄42 x 3⁄82 x 1⁄22 x 5⁄82 x 3⁄42 x 12 x 11⁄2221⁄234
12.7 x 3.212.7 x 6.412.7 x 9.512.712.7 x 15.912.7 x 19.119.1 x 3.219.1 x 6.419.1 x 9.519.1 x 12.719.1 x 15.919.125.438.1 x 3.238.1 x 6.438.1 x 9.538.1 x 12.738.1 x 15.938.1 x 19.138.1 x 31.838.150.8 x 6.450.8 x 9.550.8 x 12.750.8 x 15.950.8 x 19.150.8 x 25.450.8 x 38.150.863.576.2
101.6
1.5001.5001.5001.5001.5001.5001.5001.5001.5001.5001.5001.5001.6881.5001.5001.5001.5001.5001.5001.6881.6881.5001.5001.5001.5001.5001.6881.6882.3122.0003.0933.406
38.138.138.138.138.138.138.138.138.138.138.138.142.938.138.138.138.138.138.142.942.938.138.138.138.138.142.942.958.750.878.686.5
0.1880.2810.4060.5310.6560.7810.1880.2810.4060.5310.6560.7811.0310.1880.2810.4060.5310.6560.7811.2811.5310.2810.4060.5310.6560.7811.0311.5312.0312.5313.0314.031
4.87.1
10.313.516.719.84.87.1
10.313.516.719.826.24.87.1
10.313.516.719.832.538.97.1
10.313.516.719.826.238.951.664.377.0
102.4
0.030.030.030.030.030.040.040.040.040.050.050.050.140.280.280.280.300.300.300.400.300.550.550.600.600.600.650.650.550.801.111.51
NOTE: When ordering specify I.D. size of hose being used.1⁄2”- 3⁄4” (12.7mm - 19.1mm) available only in Type 316L Stainless Steel
Consult Jensen Fittings for availability of additional reducing sizes.
10
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC14AHRB – BREWERY STYLE LONG
111⁄2221⁄234
25.438.150.863.576.2
101.6
31⁄231⁄241⁄241⁄241⁄261⁄4
88.988.9
114.3114.3114.3158.8
11⁄32
15⁄821⁄825⁄831⁄841⁄8
26.241.354.066.779.4
104.8
0.350.450.951.251.752.75
SANITARY
KWIK
CLAMP
FITTINGS
C
D E
A
A
SIZE C D E APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
JC14AHT – TYGON HOSE ADAPTER
1⁄23⁄4111⁄2221⁄234
12.719.125.438.150.863.576.2
101.6
41⁄241⁄241⁄241⁄241⁄241⁄241⁄245⁄8
114.3114.3114.3114.3114.3114.3114.3117.5
0.3750.6250.8701.3701.8702.3702.8703.834
9.515.922.134.847.560.272.997.4
0.5000.7501.0001.5002.0002.5003.0004.000
12.719.125.438.150.863.576.2
101.6
0.030.050.310.500.680.871.121.68
JC17-14 – ADAPTERSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
33331⁄233⁄44
76.276.276.288.995.3
101.6
0.381.001.602.283.348.75
JC17-15 – ADAPTERSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
111⁄16
123⁄32
123⁄32
127⁄32
129⁄32
211⁄32
42.843.643.646.848.459.5
0.210.330.470.881.321.88
NOTE: When ordering specify I.D. size of hose being used onreducing sizes, show reduction required.
Stainless steel hex nut 304 only.
11
SANITARY
KWIK
CLAMP
FITTINGS
SIZE NO. JC21 NO. JC22 NO. JC21 NO. JC22(TUBE O.D.) C D APPROX. APPROX.
in. mm in. mm in. mm WT. LBS. WT. LBS.
JC21 & JC22 – ADAPTERS (N.P.T. Pipe Threads)
1⁄2 x 1⁄81⁄2 x 1⁄41⁄2 x 3⁄81⁄2 x 1⁄21⁄2 x 3⁄43⁄4 x 1⁄83⁄4 x 1⁄43⁄4 x 3⁄83⁄4 x 1⁄23⁄4 x 3⁄41 x 3⁄41 x 11 x 211⁄2 x 3⁄411⁄2 x 111⁄2 x 11⁄411⁄2 x 11⁄211⁄2 x 22 x 11⁄22 x 221⁄2 x 11⁄221⁄2 x 221⁄2 x 21⁄23 x 34 x 4
12.7 x 3.212.7 x 6.412.7 x 9.512.7 x 12.712.7 x 19.119.1 x 3.219.1 x 6.419.1 x 9.519.1 x 12.719.1 x 19.125.4 x 19.125.4 x 25.425.4 x 50.838.1 x 19.138.1 x 25.438.1 x 31.838.1 x 38.138.1 x 50.850.8 x 38.150.8 x 50.863.5 x 38.163.5 x 50.863.5 x 63.576.2 x 76.2
101.6 x 101.6
2.0002.0002.0002.0002.0002.0002.0002.0002.0002.0002.1872.2502.6252.1872.3122.4372.4372.6252.4682.656—2.7813.2813.5003.812
50.850.850.850.850.850.850.850.850.850.855.557.266.755.558.761.961.966.762.767.5—70.683.388.996.8
1.2501.5001.5001.5001.6251.2501.5001.5001.5001.6251.6251.625—1.6251.6252.2502.250—1.6872.3431.6561.7182.0932.1872.656
31.838.138.138.141.331.838.138.138.141.341.341.3—
41.341.357.257.2—
42.859.542.143.653.255.567.5
0.120.120.130.140.150.130.130.140.150.161.060.751.251.060.880.750.631.631.751.50
—1.941.753.255.75
0.250.250.270.280.280.250.250.270.280.290.750.56—
0.750.750.560.38—
1.751.131.881.501.252.384.00
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC16 – SOLID END CAP
1⁄2 & 3⁄41 & 11⁄2221⁄234681012
12.7 & 19.125.4 & 38.150.863.576.2
101.6152.4203.2254.0304.8
.187
.250
.250
.250
.250
.312
.437
.437
.562
.562
4.76.46.46.46.47.9
11.111.114.314.3
0.9841.9842.5163.0473.5794.6826.5708.570
10.57012.570
25.050.463.977.490.9
118.9166.9217.7268.5319.3
0.030.150.310.440.901.253.907.00
11.5015.00
C D
C D
AB
JC21(1⁄2 - 3⁄4)MALE
JC22(1⁄2 - 3⁄4)
FEMALE
JC21(1-4”)MALE
JC22(1-4”)
FEMALE
*NOTE: When adapter dimensions are given, sanitary style end is always indicated first.
NOTE: Special size adapters and fractional adapters are available on request.NOTE: 1⁄2 — 3⁄4 and 21⁄2 — 4 No hex centers
11⁄2" JC16 used on both 1" and 11⁄2" lines.3⁄4" used on both 1⁄2" and 3⁄4" lines.
12
SANITARY
KWIK
CLAMP
FITTINGS
A
B
JC31 – CONCENTRIC REDUCER
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 36 x 4
76.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 76.2152.4 x 101.6
9753131⁄8111⁄891⁄871⁄851⁄871⁄453⁄8
228.6177.8127.076.2
333.4282.6231.8181.0130.2184.2136.5
2.561.241.090.754.153.503.102.793.083.252.52
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.8
353753
76.2127.076.2
177.8127.076.2
0.290.700.400.800.630.53
JC32 – ECCENTRIC REDUCER
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 36 x 4
76.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 76.2152.4 x 101.6
9753131⁄8111⁄891⁄871⁄851⁄871⁄453⁄8
228.6177.8127.076.2
333.4282.6231.8181.0130.2184.2136.5
2.562.561.090.754.153.503.102.793.083.202.52
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.8
353753
76.2127.076.2
177.8127.076.2
0.290.700.400.800.630.53
J14-C31 – ADAPTER-REDUCER (Concentric)
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
21⁄2 x 23 x 23 x 21⁄24 x 3
63.5 x 50.876.2 x 50.876.2 x 63.5
101.6 x 76.2
311⁄32
513⁄32
313⁄32
523⁄32
84.9137.386.5
145.2
0.771.251.052.12
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
11⁄2 x 1*2 x 12 x 11⁄221⁄2 x 11⁄2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.1
37⁄32
57⁄32
37⁄32
511⁄32
81.7132.581.7
135.7
0.330.620.600.91
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
JC23B – THERMOMETER CAPS
1 & 11⁄2221⁄234
25.4 & 38.150.863.576.2
101.6
1.9842.5163.0473.5794.682
50.463.977.490.9
118.9
0.6250.6250.6250.6250.625
15.915.915.915.915.9
0.500.751.131.542.75
JC23B - 1" Tapped 1⁄2" NPT. All others 3⁄4".
*Includes Stainless Steel Hex Nut
13
SANITARY
KWIK
CLAMP
FITTINGS
JC31-15 – ADAPTER-REDUCER (Concentric)
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
21⁄2 x 23 x 23 x 21⁄24 x 3
63.5 x 50.876.2 x 50.876.2 x 63.5
101.6 x 76.2
37⁄32
57⁄32
311⁄32
517⁄32
81.7132.584.9
140.5
0.701.131.062.02
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 11⁄2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.1
33⁄16
53⁄16
37⁄32
57⁄32
80.9131.781.7
132.5
0.360.590.560.82
JC15-C31 – ADAPTER-REDUCER (Concentric)
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3 x 23 x 21⁄24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 63.5101.6 x 76.2
513⁄32
313⁄32
723⁄32
523⁄32
137.386.5
196.0145.2
1.151.103.252.50
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 11⁄221⁄2 x 2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.163.5 x 50.8
37⁄32
57⁄32
37⁄32
511⁄32
311⁄32
81.7132.581.7
135.784.9
0.380.600.580.850.72
JC31-14 – ADAPTER-REDUCER (Concentric)
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3 x 23 x 21⁄24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 63.5101.6 x 76.2
613⁄32
421⁄32
825⁄32
615⁄16
162.7118.3223.0176.2
1.771.993.393.63
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 11⁄221⁄2 x 2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.163.5 x 50.8
41⁄861⁄847⁄32
67⁄32
413⁄32
104.8155.6107.1157.9111.9
0.580.830.951.231.43
J14-C32 – ADAPTER-REDUCER (Eccentric)
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3 x 23 x 21⁄24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 63.5101.6 x 76.2
513⁄32
313⁄32
723⁄32
523⁄32
137.386.5
196.0145.2
1.050.932.461.96
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
11⁄2 x 1*2 x 12 x 11⁄221⁄2 x 11⁄221⁄2 x 2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.163.5 x 50.8
37⁄32
57⁄32
37⁄32
511⁄32
311⁄32
81.7132.581.7
135.784.9
0.390.710.530.830.68
JC32-14 – ADAPTER-REDUCER (Eccentric)
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3 x 23 x 21⁄24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 63.5101.6 x 76.2
613⁄32
421⁄32
825⁄32
615⁄16
162.7118.3223.0176.2
1.742.073.393.45
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 11⁄221⁄2 x 2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.163.5 x 50.8
41⁄861⁄847⁄32
67⁄32
413⁄32
104.8155.6107.1157.9111.9
0.590.820.961.231.43
*Includes Stainless Steel Hex Nut
14
SANITARY
KWIK
CLAMP
FITTINGS
J15-C32 – ADAPTER-REDUCER (Eccentric)
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3 x 23 x 21⁄24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 63.5101.6 x 76.2
513⁄32
313⁄32
723⁄32
523⁄32
137.386.5
196.0145.2
1.241.122.852.35
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 11⁄221⁄2 x 2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.163.5 x 50.8
37⁄32
57⁄32
37⁄32
511⁄32
311⁄32
81.7132.581.7
135.784.9
0.450.760.590.990.84
JC32-15 – ADAPTER-REDUCER (Eccentric)
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3 x 23 x 21⁄24 x 24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 50.8101.6 x 63.5101.6 x 76.2
57⁄32
311⁄32
911⁄32
715⁄32
517⁄32
132.584.9
237.3189.7140.5
1.021.032.352.351.94
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 11⁄221⁄2 x 23 x 11⁄2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.163.5 x 50.876.2 x 38.1
33⁄16
53⁄16
37⁄32
57⁄32
37⁄32
77⁄32
80.9131.781.7
132.581.7
183.3
0.340.570.510.780.711.31
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
JC28A – KWIK CLAMP LATERALAND REDUCING LATERAL
1⁄23⁄4111⁄2221⁄23461 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 1⁄23 x 3⁄43 x 13 x 11⁄23 x 23 x 21⁄24 x 1⁄24 x 3⁄44 x 14 x 11⁄24 x 24 x 21⁄24 x 3
12.719.125.438.150.863.576.2
101.6152.425.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 12.776.2 x 19.176.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 12.7101.6 x 19.1101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
11⁄211⁄211⁄413⁄815⁄821⁄821⁄2343⁄411⁄411⁄413⁄813⁄813⁄815⁄815⁄815⁄815⁄821⁄821⁄821⁄821⁄821⁄821⁄221⁄221⁄221⁄221⁄221⁄23333333
38.138.131.834.941.354.063.576.2
120.731.831.834.934.934.941.341.341.341.354.054.054.054.054.063.563.563.563.563.563.576.276.276.276.276.276.276.2
31⁄231⁄245⁄16
51⁄16
51⁄267⁄881⁄410131⁄445⁄16
45⁄16
51⁄16
51⁄16
51⁄16
51⁄251⁄251⁄251⁄251⁄267⁄867⁄867⁄867⁄867⁄881⁄481⁄481⁄481⁄481⁄410101010101010
88.988.9
109.5128.6139.7174.6209.6254.0336.6109.5109.5128.6128.6128.6139.7139.7139.7139.7139.7174.6174.6174.6174.6174.6209.6209.6209.6209.6209.6254.0254.0254.0254.0254.0254.0254.0
31⁄231⁄233⁄8441⁄251⁄2783⁄4131⁄433⁄833⁄844441⁄241⁄241⁄241⁄251⁄251⁄251⁄251⁄251⁄277777783⁄483⁄483⁄483⁄483⁄483⁄483⁄4
88.988.985.7
101.6114.3139.7177.8222.3336.685.785.7
101.6101.6101.6114.3114.3114.3114.3139.7139.7139.7139.7139.7177.8177.8177.8177.8177.8177.8222.3222.3222.3222.3222.3222.3222.3
0.400.550.911.221.992.903.467.39
15.560.900.901.201.211.221.951.951.961.982.502.502.652.752.853.353.353.403.423.443.467.007.007.167.207.237.257.34
JC28B – KWIK CLAMP TRUE YSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
21⁄221⁄231⁄231⁄241⁄251⁄261⁄285⁄883⁄4
63.563.588.988.9
114.3139.7165.1219.1222.3
0.350.450.901.101.902.333.015.15
12.70
B
A C
A
A
A Swagelok Company
Industrial
Kwik-Clamp
Fittings
15
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
7MO – TEE
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
23⁄823⁄431⁄231⁄233⁄441⁄253⁄4
60.369.988.988.995.3
114.3146.1
43⁄451⁄27771⁄29111⁄2
120.7139.7177.8177.8190.5228.6292.1
0.380.691.381.592.503.88
12.20A
A
B
INDUSTRIAL
KWIK
CLAMP
FITTINGS
16
2CLMO – 90˚ ELL
A
A
R
A
A R
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
223⁄431⁄241⁄4565⁄8101⁄2
50.869.988.9
108.0127.0168.3266.7
11⁄221⁄4333⁄441⁄269
38.157.276.295.3
114.3152.4228.6
0.350.440.811.002.003.66
12.10
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
2KMO – 45˚ ELL
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
11⁄817⁄16
13⁄421⁄16
23⁄831⁄841⁄2
28.636.544.552.460.379.4
114.3
11⁄221⁄4333⁄441⁄269
38.157.276.295.3
114.3152.4228.6
0.240.310.500.571.192.257.80
INDUSTRIAL POLISH CODES:Code Finish
1 NOT POLISHED, MILL FINISH3 32 Ra ID POLISHED, NOT POLISHED OD5 NOT POLISHED ID, POLISHED 32Ra OD
17
INDUSTRIAL
KWIK
CLAMP
FITTINGS
31-14MO – CONCENTRIC REDUCER
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3 x 1⁄23 x 3⁄43 x 13 x 11⁄23 x 23 x 21⁄24 x 1⁄24 x 3⁄44 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 36 x 4
76.2 x 12.776.2 x 19.176.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 12.7101.6 x 19.1101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 76.2152.4 x 101.6
91⁄299753135⁄8131⁄8131⁄8111⁄891⁄871⁄851⁄871⁄453⁄8
241.3228.6228.6177.8127.076.2
346.1333.4333.4282.6231.8181.0130.2184.2136.5
2.702.562.561.241.090.754.154.154.153.503.102.793.083.252.52
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3⁄4 x 1⁄21 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 2
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.8
221⁄2231⁄23351⁄255371⁄27753
50.863.550.888.976.276.2
139.7127.0127.076.2
190.5177.8177.8127.076.2
0.220.230.240.260.260.290.650.700.700.400.950.800.800.630.53
32-14MO – ECCENTRIC REDUCER
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3 x 1⁄23 x 3⁄43 x 13 x 11⁄23 x 23 x 21⁄24 x 1⁄24 x 3⁄44 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 36 x 4
76.2 x 12.776.2 x 19.176.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 12.7101.6 x 19.1101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 76.2152.4 x 101.6
91⁄299953135⁄8131⁄8131⁄8111⁄891⁄871⁄851⁄871⁄453⁄8
241.3228.6228.6228.6127.076.2
346.1333.4333.4282.6231.8181.0130.2184.2136.5
2.702.562.562.561.090.754.154.154.153.503.102.793.083.202.52
SIZE OVERALL APPROX.LENGTH WT. LBS.in. mm in. mm
3⁄4 x 1⁄21 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 2
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.8
221⁄2231⁄23351⁄255371⁄27753
50.863.550.888.976.276.2
139.7127.0127.076.2
190.5177.8177.8127.076.2
.22
.23
.24
.26
.26
.29
.65
.70
.70
.40
.95
.80
.80
.63
.53
C
D E
SIZE C D E APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
14-WLMO – TANK WELDING SPUD (Light)
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
3333446
76.276.276.276.2
101.6101.6152.4
0.8701.3701.8702.3702.8703.8345.782
22.134.847.560.272.997.4
146.9
1.0001.5002.0002.5003.0004.0006.000
25.438.150.863.576.2
101.6152.4
0.160.210.400.540.771.252.32
INDUSTRIAL
KWIK
CLAMP
FITTINGS
18
ADAPTERS
304 s/s or 316L s/s
A Swagelok Company
Butt
Weld
Fittings
19
BUTT
WELD
FITTINGS
20
Jensen has crafted stainless steel sanitary butt weld fittings since 1959 for the Brewery, Winery,
Beverage, Food, Dairy and Pharmaceutical industries. Dimensions shown in this catalog are to standards
accepted by the industry.
Sanitary fittings, crevice free and smooth bored are made to tube
outside diameter dimensions and should not be confused with
nominal pipe size. To identify existing line sizes measure the
diameter to the outside as your reference.
These butt weld fittings are manufactured to close tolerances to permit fast and easy installation of crevice free,
fully sanitary and corrosion resistant process lines. All welds used in manufacturing are of the Tungsten Inert
Gas Method for true fusion of wall with no thinning or pitting. Availability is in Type 304 & 316L stainless steel.
Heat traceability is available on all 316L fittings, if specified at the time of order.
Jensen offers four finishes to suit your needs. The following should be referred to and the appropriate code
number used when ordering.
Code Finish1 NOT POLISHED, MILL FINISH3 32 Ra ID POLISHED, NOT POLISHED OD5 NOT POLISHED ID, POLISHED 32 Ra OD7 32 Ra ID POLISHED, 32 Ra OD POLISHED
21
BUTT
WELD
FITTINGS
J2SX – 90˚ ELLSIZE A NOM.WALL(TUBE O.D.) THICKNESS
in. mm in. mm
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
11⁄221⁄4333⁄441⁄269
38.157.276.295.3
114.3152.4228.6
.065
.065
.065
.065
.065
.065
.083
SIZE A NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
21⁄16
215⁄16
41⁄16
53⁄16
65⁄16
85⁄16
52.474.6
103.2131.7160.3211.1
.065
.065
.065
.065
.065
.083
J2S – 90˚ TUBE BEND
SIZE A B NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm in. mm
J2CM – KWIK CLAMP ONE END
111⁄2221⁄234
25.438.150.863.576.2
101.6
21⁄16
215⁄16
41⁄16
53⁄16
65⁄16
85⁄16
52.474.6
103.2131.7160.3211.1
29⁄16
37⁄16
49⁄16
511⁄16
613⁄16
815⁄16
65.187.3
115.9144.4173.0227.0
.065
.065
.065
.065
.065
.083
SIZE A B D NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm in. mm in. mm
J2F 90˚ SWEEP ELL
111⁄2221⁄234
25.438.150.863.576.2
101.6
21⁄16
215⁄16
41⁄16
53⁄16
65⁄16
85⁄16
52.474.6
103.2134.9160.3211.1
23⁄4321⁄32
425⁄32
61⁄32
77⁄32
917⁄32
69.992.9
121.4153.2183.3242.1
111⁄2221⁄234
25.438.150.863.576.2
101.6
.065
.065
.065
.065
.065
.083
SIZE A NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
13⁄16
15⁄825⁄16
3311⁄16
413⁄16
30.1
41.3
58.7
.065
.065
.065
.065
.065
.083
J2KS – 45˚ TUBE BEND
A
A
A
B
A
A
DB
A
A
22
BUTT
WELD
FITTINGS
SIZE C D NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm in. mm
J2KM – 45˚ TUBE BEND KWIK CLAMP ONE END
111⁄2221⁄234
25.438.150.863.576.2
101.6
111⁄16
21⁄8213⁄16
31⁄243⁄16
57⁄16
42.854.071.488.9
106.3138.1
.065
.065
.065
.065
.065
.083
13⁄16
15⁄825⁄16
3311⁄16
413⁄16
30.141.358.776.293.6
122.2
SIZE C D NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm in. mm
J2K – 45˚ TUBE BEND THREADED ONE END
111⁄2221⁄234
25.438.150.863.576.2
101.6
17⁄8211⁄32
31⁄32
327⁄32
419⁄32
61⁄32
47.659.577.097.6
116.7153.2
.065
.065
.065
.065
.065
.083
13⁄16
15⁄825⁄16
3311⁄16
413⁄16
30.141.358.776.293.6
122.2
SIZE C D NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm in. mm
J2P – 45˚ TUBE BEND PLAIN ONE END
111⁄2221⁄234
25.438.150.863.576.2
101.6
17⁄8211⁄32
31⁄32
327⁄32
419⁄32
61⁄32
47.659.577.097.6
116.7153.2
.065
.065
.065
.065
.065
.083
13⁄16
15⁄825⁄16
3311⁄16
413⁄16
30.141.358.776.293.6
122.2
SIZE B NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
17⁄821⁄43331⁄437⁄8
47.657.276.276.282.698.4
.065
.065
.065
.065
.065
.083
J9W – CROSS
SIZE B NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
17⁄821⁄43331⁄437⁄8
47.657.276.276.282.698.4
.065
.065
.065
.065
.065
.083
J7W – TEE
C
D
C
D
C
D
F
F
E
B
B
B B
23
BUTT
WELD
FITTINGS
J7WR – REDUCING TEESIZE A AA NOM.WALL(TUBE O.D.) THICKNESS
in. mm in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 X 36 X 4
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 76.2152.4 x101.6
21⁄43333331⁄431⁄431⁄431⁄437⁄837⁄837⁄837⁄837⁄855
57.276.276.276.276.276.282.682.682.682.698.498.498.498.498.4
127.0127.0
21⁄823⁄821⁄223⁄423⁄431⁄431⁄8331⁄231⁄435⁄835⁄8433⁄433⁄443⁄447⁄8
54.060.363.569.969.982.679.476.288.982.692.192.1
101.695.395.3
120.7123.8
0.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0830.0830.0830.0830.0830.1090.109
SIZE B C NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm in. mm
J7WWM – KWIK CLAMP TEE
111⁄2221⁄234
25.438.150.863.576.2
101.6
15⁄825⁄32
29⁄16
227⁄32
33⁄32
41⁄16
41.354.865.172.278.6
103.2
.065
.065
.065
.065
.065
.083
11⁄8121⁄32
21⁄16
211⁄32
219⁄32
37⁄16
28.642.152.459.565.987.3
SIZE A B C NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm in. mm in. mm
J31 – CONCENTRIC REDUCER
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 16 x 11⁄26 x 26 x 21⁄26 x 36 x 4
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 25.4152.4 x 38.1152.4 x 50.8152.4 x 63.5152.4 x 76.2152.4 x101.6
24264286421210864141210864
50.8101.650.8
152.4101.650.8
203.2152.4101.650.8
304.8254.0203.2152.4101.6355.6304.8254.0203.2152.4101.6
11⁄22221⁄221⁄221⁄2333344444666666
38.150.850.863.563.563.576.276.276.276.2
101.6101.6101.6101.6101.6152.4152.4152.4152.4152.4152.4
1111⁄2111⁄22111⁄2221⁄2111⁄2221⁄23111⁄2221⁄234
25.425.438.125.438.150.825.438.150.863.525.438.150.863.576.225.438.150.863.576.2
101.6
0.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0830.0830.0830.0830.0830.1090.1090.1090.1090.1090.109
A
CB
C
B B
AA
A A
24
BUTT
WELD
FITTINGS
SIZE A B C NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm in. mm in. mm
J32 – ECCENTRIC REDUCER
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 16 x 11⁄26 x 26 x 21⁄26 x 36 x 4
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 25.4152.4 x 38.1152.4 x 50.8152.4 x 63.5152.4 x 76.2152.4 x101.6
24264286421210864141210864
50.8101.650.8
152.4101.650.8
203.2152.4101.650.8
304.8254.0203.2152.4101.6355.6304.8254.0203.2152.4101.6
11⁄22221⁄221⁄221⁄2333344444666666
38.150.850.863.563.563.576.276.276.276.2
101.6101.6101.6101.6101.6152.4152.4152.4152.4152.4152.4
1111⁄2111⁄22111⁄2221⁄2111⁄2221⁄23111⁄2221⁄234
25.425.438.125.438.150.825.438.150.863.525.438.150.863.576.225.438.150.863.576.2
101.6
0.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0830.0830.0830.0830.0830.1090.1090.1090.1090.1090.109
J31P – CONCENTRIC REDUCER ONE END PLAINSIZE A C NOM.WALL(TUBE O.D.) THICKNESS
in. mm in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
211⁄16
423⁄32
223⁄32
627⁄32
427⁄32
227⁄32
829⁄32
629⁄32
429⁄32
229⁄32
137⁄32
117⁄32
97⁄32
77⁄32
57⁄32
68.2119.869.0
173.8123.072.2
226.2175.4124.673.8
335.7284.9234.1183.3132.5
1111⁄2111⁄22111⁄2221⁄2111⁄2221⁄23
25.425.438.125.438.150.825.438.150.863.525.438.150.863.576.2
0.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0830.0830.0830.0830.083
J32P – ECCENTRIC REDUCER ONE END PLAINSIZE A C NOM.WALL(TUBE O.D.) THICKNESS
in. mm in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
211⁄16
423⁄32
223⁄32
627⁄32
427⁄32
227⁄32
829⁄32
629⁄32
429⁄32
229⁄32
137⁄32
117⁄32
97⁄32
77⁄32
57⁄32
68.2119.869.0
173.8123.072.2
226.2175.4124.673.8
335.7284.9234.1183.3132.5
1111⁄2111⁄22111⁄2221⁄2111⁄2221⁄23
25.425.438.125.438.150.825.438.150.863.525.438.150.863.576.2
0.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0830.0830.0830.0830.083
A
CB
A
C
C
A
25
BUTT
WELD
FITTINGS
J31M – CONCENTRIC REDUCER KWIK CLAMPSIZE A C NOM.WALL(TUBE O.D.) THICKNESS
in. mm in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
21⁄241⁄221⁄261⁄241⁄221⁄281⁄261⁄241⁄221⁄2125⁄8105⁄885⁄865⁄845⁄8
63.5114.363.5
165.1114.363.5
215.9165.1114.363.5
320.7269.9219.1168.3117.5
1111⁄2111⁄22111⁄2221⁄2111⁄2221⁄23
25.425.438.125.438.150.825.438.150.863.525.438.150.863.576.2
0.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0830.0830.0830.0830.083
J32M – ECCENTRIC REDUCER KWIK CLAMPSIZE A C NOM.WALL(TUBE O.D.) THICKNESS
in. mm in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
21⁄241⁄221⁄261⁄241⁄221⁄281⁄261⁄241⁄221⁄2125⁄8105⁄885⁄865⁄845⁄8
63.5114.363.5
165.1114.363.5
215.9165.1114.363.5
320.7269.9219.1168.3117.5
1111⁄2111⁄22111⁄2221⁄2111⁄2221⁄23
25.425.438.125.438.150.825.438.150.863.525.438.150.863.576.2
0.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0830.0830.0830.0830.083
J28BW – TRUE YSIZE A NOM.WALL(TUBE O.D.) THICKNESS
in. mm in. mm1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
223345688
50.850.876.276.2
101.6127.0152.4203.2203.2
0.0650.0650.0650.0650.0650.0650.0650.0800.109
C
A
C
A
A
A
26
BUTT
WELD
FITTINGS
SIZE A B C NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm in. mm in. mm
J28WA – LATERAL YAND J28WAR REDUCING LATERAL Y
1⁄23⁄4111⁄2221⁄23461 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 1⁄23 x 3⁄43 x 13 x 11⁄23 x 23 x 21⁄24 x 1⁄24 x 3⁄44 x 14 x 11⁄24 x 24 x 21⁄24 x 3
12.719.125.438.150.863.576.2
101.6152.425.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 12.776.2 x 19.176.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 12.7101.6 x 19.1101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
66673⁄883⁄410103⁄41213⁄16
161⁄26673⁄873⁄873⁄883⁄483⁄483⁄483⁄41010101010103⁄4103⁄4103⁄4103⁄4103⁄4103⁄41213⁄16
1213⁄16
1213⁄16
1213⁄16
1213⁄16
1213⁄16
1213⁄16
152.4152.4152.4187.3222.3254.0273.1325.4419.1152.4152.4187.3187.3187.3222.3222.3222.3222.3254.0254.0254.0254.0254.0273.1273.1273.1273.1273.1273.1325.4325.4325.4325.4325.4325.4325.4
55563⁄16
71⁄881⁄287⁄8103⁄4121⁄25563⁄16
63⁄16
63⁄16
71⁄871⁄871⁄871⁄881⁄281⁄281⁄281⁄281⁄287⁄887⁄887⁄887⁄887⁄887⁄8103⁄4103⁄4103⁄4103⁄4103⁄4103⁄4103⁄4
127.0127.0127.0157.1181.0215.9225.4273.1317.5127.0127.0157.1157.1157.1181.0181.0181.0181.0215.9215.9215.9215.9215.9225.4225.4225.4225.4225.4225.4273.1273.1273.1273.1273.1273.1273.1
11113⁄16
15⁄811⁄217⁄821⁄16
41113⁄16
13⁄16
13⁄16
15⁄815⁄815⁄815⁄811⁄211⁄211⁄211⁄211⁄217⁄817⁄817⁄817⁄817⁄817⁄821⁄16
21⁄16
21⁄16
21⁄16
21⁄16
21⁄16
21⁄16
25.425.425.430.141.338.147.652.4
101.625.425.430.130.130.141.341.341.341.338.138.138.138.138.147.647.647.647.647.647.652.452.452.452.452.452.452.4
0.0650.0650.0650.0650.0650.0650.0650.0830.1090.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0650.0830.0830.0830.0830.0830.0830.083
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
14WHR – BUTT WELD RUBBER HOSE ADAPTER
1⁄23⁄4111⁄2221⁄234
12.719.125.438.150.863.576.2
101.6
1.5001.5001.6881.6882.3122.0003.0933.406
38.138.142.942.958.750.878.686.5
0.5310.7811.0311.5312.0312.5313.0314.031
13.519.826.238.951.664.377.0
102.4
0.040.060.090.130.200.250.310.56
B
CA
A Swagelok Company
27
Bio-Pharm
Fittings
• Swagelok TS• Sanitary Clamp Connections
28
BIO
PHARM
FITTINGS
Jensen is producing its Bio-Pharm Fittings to the ASME-BPE standard. All products are marked with the corresponding heat number(s), the ASME-BPE Spec, internal surface symbol for the appropriateBPE specification, grade of material, plus manufacturer markings (JF).
This allows for full identification and traceability while providing a low cost, quality fitting to the BPEspecifications. Our pharmaceutical (TL/AWF) product line is available in 1/2"(12.7mm) through6"(152.4mm) in 316L stainless steel. Each fitting undergoes an intensive quality control process to
ensure all specifications of the order are met. This conforms to our ISO 9002 registered program.
Materials Test Reports are included with all extended tangent and Optional Finish material. We include a set of M.T.R.'s with your shipment of material and a set with your invoice. All heat numbers are includedon all barcode labels, packing slips, and invoices for easy comparison to the fittings, including multiple heat numbers if it is a complex fitting.
29
BIO
PHARM
FITTINGS
Jensen offers four finishes on bio-pharm fittings to suit your needs. The following should be referred to and the appropriate code number used when ordering.
Swagelok TS fitting finishes indicated on page 30.
Code BPE Code Finish
3 PC SFF1 20 Ra Max ID Polished,Not Polished OD
7 PL SFF1 20 Ra Max ID Polished,32 Ra OD Polished
3 PD SFF4 15 Ra Max ID Polished and IDElectropolished, Not Polished
7 PD SFF4 15 Ra Max ID Polished and IDElectropolished, 32 Ra OD Polished
30
BIO
PHARM
FITTINGS
Sanitary Fittings
Crown
Expansionspace
Rib
Features
Swagelok TS Series ISO 2852
Metal-to-metal stop
Temperature Ratings
Technical Data
Design Specifications� TS series 316L stainless steel ferrules meet
ASME- BPE and 3-A requirements.
� Short ferrules meet ASME-BPE with the exception of overall length.
Internal Surface Finish� Mechanical finish (designator SFF1):
20 µin. max Ra according to ASME-BPE.
� Electropolished finish (designator SFF4): 15 µin. max Ra according to ASME-BPE.
External Surface Finish� 64 µin. Ra
Material SpecificationsAll wetted components are traceable. Ferrules are heat trace-able, while gasket materials are lot traceable.
CleaningFerrules and clamps are cleaned to ensure components are freeof burrs, chips, loose particles, oil, grease, and other contami-nants. Electropolished ferrules are passivated.
Materials of Construction
Item Material Specification
Ferrules 316L stainless steel ASME BPE3-A 63-02
Clamps 304 stainless steel ISO 2852
Gaskets
FDA-21CFR177.15503-A 20-20PTFE
FDA-21CFR177.2660 3-A 18-03
ISO 10993 part 5 (cytotoxicity test),
USP 23, Section 88, Class VI
EPDM
Swagelok TS Series Sanitary FittingsSwagelok TS series sanitary fittings are designed to solveproblems inherent in conventional ISO 2852 sanitary fittings: gasket extrusion and the resulting fluid holdup. During assembly,the metal-to-metal stop of the TS series sanitary ferrules preventsovertightening and controls gasket compression. Another benefitof a metal-to-metal stop is its inherent ability to maintain a borelineseal by restricting ferrule movement. The unique design of the TS series controls gasket extrusion and deformation under avariety of operating conditions including thermal cycling. As aresult, systems drain better, clean faster, sterilize more easily, and improve yields.Conventional ISO 2852 sanitary fittings utilize a design that, when tightened, allows the gasket to extrude into the boreline ofprocess piping and creates a barrier that holds up fluids. This fluidholdup may require longer cleaning cycles, making sterilization andvalidation more difficult.
TS Series Highlights� Virtually eliminates fluid holdup. Because of its boreline seal
design and metal-to-metal stop, gasket compression is controlledand ferrule movement is restricted at both ambient and elevatedtemperatures. The result is virtually no fluid holdup.
� Improved drainability/cleanability. Improved drainability andcleanability are ensured by the dramatic reduction of fluid holdup.
� Leak-tight performance. The assembly remains leak-tightthroughout the range of temperature ratings.
� Easy assembly. TS series elastomer gaskets utilize aninterference fit that allows the TS series ferrule to "capture" theself-aligning gasket, making assembly of the mating ferrule andclamp easier than that of conventional ISO 2852 fittings.
� Flexibility and adaptability. A TS series adapter gasket isavailable. It allows an existing ISO 2852 ferrule to mate with a TS series ferrule while providing some advantages of acomplete TS connection.
Material Rating, °F (°C)
PTFE 60 to 275 (15 to 135)
EPDM -50 to 275 (-46 to 135)
Vacuum Testing
Gasket Material Vacuum Rating
EPDM10-3 Torr
Fluorocarbon (FKM)
Fluorocarbon (FKM) -10 to 350 (-23 to 177)
The metal-to-metal stop acts as a built-in gage to allow precise,controlled gasket compression.The rib creates a boreline seal.The crown holds the gasket in place, centering the rib over thesealing area. During thermal cycling, the crown directs expansionto the space provided.
Fluorocarbon➀ (FKM)
➀ Equivalent to DuPont Viton®
31
BIO
PHARM
FITTINGS
Sanitary FittingsPressurePressure ratings are based upon testsconducted using a 2-piece clamp for 1/2 and 3/4 in. fittings and a 3-piececlamp for 1 through 4 in. fittings.Note: Pressure ratings for connectionsutilizing an adapter gasket or any other manufacturer’s component default to the lowest pressure rating of the components.
Dimensions/Ordering Information
H
BET
H
BET
H
BNote: 1/2 and 3/4 in. OD fer-rules, cap and clamp are basedon commonly available fittingassemblies (25mm), not ISO2852 (34mm).
Dimensions for reference only,subject to change.
Fitting Size
in. (mm)
PTFE 1⁄2 to 2 (12.7 to 50.8) 200 (13.8)
EPDM
FKM
1⁄2 (12.7)
300 (20.5)
at 275°F (135°C)
3⁄4 (19.1)
1 (25.4)
21⁄2 (63.5)
11⁄2 (38.1)
2 (50.8)
3 (76.2)(
2800 (192)
0200 (13.8)
3100 (213)
at 70°F (20°C)
650 (44.7)
0450 (31.0)
1200 (82.6)
0350 (24.1)
4 (101.6) 0200 (13.8)
Tube OD in. (mm)
Basic Ordering Number
Dimensions, in. (mm)
B E H T1⁄2 (12.7) 316L-8TS-S-
0.98 (24.9)0.37 (9.4)
0.50(12.7)
0.50 (12.7)
3⁄4 (19.1) 316L-12TS-S- 0.62 (15.7) 0.75 (19.1)
1 (25.4) 316L-16TS-S-1.98 (50.3)
0.87 (22.1) 1.00 (25.4)
11⁄2 (38.1) 316L-24TS-S- 1.37 (34.8) 1.50 (38.1)
2 (50.8) 316L-32TS-S- 2.52 (64.0) 1.87 (47.5) 2.00 (50.8)
Short Ferrules(0.065 in. wall)
How to OrderSelect a Basic Ordering Number. Add internal surface finish designator to the Basic Ordering Number.
Standard Ferrules(0.065 in. wall)
Caps
Tube OD in. (mm)
Basic Ordering Number
Dimensions, in. (mm)
B E H T1⁄2 (12.7) 316L-8TS-L-
0.98 (24.9)0.37 (9.4)
1.75 (44.4)
0.50 (12.7)
3⁄4 (19.1) 316L-12TS-L- 0.62 (15.7) 0.75 (19.1)
1 (25.4) 316L-16TS-L-1.98 (50.3)
0.87 (22.1) 1.00 (25.4)
11⁄2 (38.1) 316L-24TS-L- 1.37 (34.8) 1.50 (38.1)
2 (50.8) 316L-32TS-L- 2.52 (64.0) 1.87 (47.5) 2.00 (50.8)
2.25 (57.2)
4 (101.6)316L-64TS-L-(0.083 in. wall) 4.68 (118.9) 3.83 (97.3) 4.00 (101.6)
3 (76.2) 316L-48TS-L- 3.58 (90.9) 2.87 (72.9) 3.00 (76.2)
21⁄2 (63.5) 316L-40TS-L- 3.05 (77.5) 2.37 (60.2) 2.50 (63.5)
Tube OD in. (mm)
Basic Ordering Number
Dimensions, in. (mm)
B H1⁄2 (12.7) 316L-8TS-C-
0.25 (6.4)
3⁄4 (19.1) 316L-12TS-C-
1 (25.4) 316L-16TS-C-
11⁄2 (38.1) 316L-24TS-C-
2 (50.8) 316L-32TS-C-
21⁄2 (63.5) 316L-40TS-C-➁
3 (76.2) 316L-48TS-C-➁
4 (101.6) 316L-64TS-C-➁
0.98 (24.9)
3.58 (90.9)
2.52 (64.0)
1.98 (50.3)
3.05 (77.5)
4.68 (118.9)
200 (13.8) 200 (13.8) (FKM only)
N/A
300 (20.5)(FKM only)
at 350°F (177°C)
Pressure, psig (bar)
➁ 2 1/2 to 4 in. TS caps are not made according to ASME-BPE material specifications.
316L – 8TS – S – SFF1
Internal Surface Finish DesignatorSFF1 Mechanical Finish (20 µin. max Ra) according to ASME BPESFF4 Electropolish Finish (15 µin. max Ra) according to ASME BPE
Overall Length DesignatorS 0.50 in. (12.7 mm), 1/2 to 2 in. ODL 1.75 in. (44.4 mm), 1/2 to 1 1/2 in. OD
2.25 in. (57.2 mm), 2 to 4 in. OD
TS Series Size Designator, inches8TS 1/2 32TS 2
12TS 3/4 40TS 2 1/216TS 1 48TS 324TS 1 1/2 64TS 4
Material Designator316L 316L Stainless Steel
GasketMaterial
32
BIO
PHARM
FITTINGS
The following validation documentation can be provided upon request:� Certified Mill Test Reports� Certification of compliance to specifications� Certification of compliance to CFR Title #21 section 177� Quality assurance manual� ISO 9001 certification
Welding� Note: Manual welding is not recommended for short ferrules.
Welding caution: Excess heat may alter the ferrule shape and affect seal integrity.
� Please contact your Swagelok representative for additionalinformation on recommended welding practices.
Gaskets Adapter Gaskets
Options and Accessories
TS series adapter gaskets provide an easy method of transitionbetween ISO 2852 and TS systems. This gasket is designed with a different profile on each face; one profile accommodates the ISO 2852 ferrule and the other fits the TS series ferrule.
Wing Nut Tightening ToolThe Swagelok wing nut tightening tool simplifies thetask of tightening and untightening wing nuts. It canalso protect individuals from hot wing nuts.
MaterialSizein.
Ordering Number
PTFE(white)
1⁄2 (12.7) TM-8TS-G
EPDM(black)
3⁄4 (19.1) TM-12TS-G1 (25.4) TM-16TS-G
11⁄2 (38.1) TM-24TS-G2 (50.8) TM-32TS-G1⁄2 (12.7) EP-8TS-G3⁄4 (19.1) EP-12TS-G1 (25.4) EP-16TS-G
11⁄2 (38.1) EP-24TS-G2 (50.8) EP-32TS-G
21⁄2 (63.5) EP-40TS-G3 (76.2) EP-48TS-G4 (101.6) EP-64TS-G
Ordering Number
NY-TS-TL
FKM(brown)
21⁄2 (63.5) VT-40TS-G
1⁄2 (12.7) VT-8TS-G3⁄4 (19.1) VT-12TS-G
3 (76.2)
1 (25.4) VT-16TS-G
VT-48TS-G
11⁄2 (38.1) VT-24TS-G2 (50.8) VT-32TS-G
4 (101.6) VT-64TS-G
MaterialSizein.
Ordering Number
PTFE(white)
1⁄2 (12.7) TM-8TS-GA
EPDM(black)
3⁄4 (19.1) TM-12TS-G1 (25.4) TM-16TS-GA
11⁄2 (38.1) TM-24TS-GA2 (50.8) TM-32TS-GA1⁄2 (12.7) EP-8TS-GA3⁄4 (19.1) EP-12TS-G1 (25.4) EP-16TS-GA
11⁄2 (38.1) EP-24TS-GA2 (50.8) EP-32TS-GA
21⁄2 (63.5) EP-40TS-GA3 (76.2) EP-48TS-GA4 (101.6) EP-64TS-GA
FKM(brown)
21⁄2 (63.5) VT-40TS-GA
1⁄2 (12.7) VT-8TS-GA3⁄4 (19.1) VT-12TS-G
3 (76.2)
1 (25.4) VT-16TS-GA
VT-48TS-GA
11⁄2 (38.1) VT-24TS-GA2 (50.8) VT-32TS-GA
4 (101.6) VT-64TS-GA
33
BIO
PHARM
FITTINGS
The following configurations represent sanitary connections and are identified by thenumber at the top of each table. These same fittings with the same dimensions are also availablewith the Swagelok TS fitting. Please consult your local Swagelok distributor.
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
JTL2CM – KWIK CLAMP ONE END 90˚ ELBOW
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
3.003.003.003.754.755.506.258.00
11.50
76.276.276.295.3
120.7139.7158.8203.2292.1
1.621.622.002.753.504.255.006.62
10.50
41.141.150.869.988.9
108.0127.0168.1266.7
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
JTL2KM – KWIK CLAMP ONE END 45˚ ELL
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
2.252.252.252.503.003.373.624.506.25
57.257.257.263.576.285.691.9
114.3158.8
1.001.001.121.441.752.062.383.125.25
25.425.428.436.644.552.360.579.2
133.4
A
A
A
A
BPE - Table # DT-7
BPE - Table # DT-12
BPE - Table # DT-8
BPE - Table # DT-13
SIZE A(TUBE O.D.)in. mm in. mm
JTL2S – 90 ̊TANGENT ELBOW
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
3.003.003.003.754.755.506.258.00
11.50
76.276.276.295.3
120.7139.7158.8203.2292.1
SIZE A(TUBE O.D.)in. mm in. mm
JTL2KS – 45 ̊TANGENT ELL
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
2.252.252.252.503.003.373.624.506.25
57.257.257.263.576.285.691.9
114.3158.8
A
B
A
B
34
BIO
PHARM
FITTINGS
SIZE B C(TUBE O.D.)in. mm in. mm in. mm
JTL7WWM – KWIK CLAMP TANGENT TEE
1⁄23⁄4111⁄2221⁄234
12.719.125.438.150.863.576.2
101.6
1.872.002.122.372.873.123.374.12
47.550.853.860.272.979.285.6
104.6
2.372.502.622.873.373.623.874.75
60.263.566.572.985.691.998.3
120.7
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
JTL7WMS – KWIK CLAMP TANGENT TEE SHORT
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
1.872.002.122.372.873.123.374.125.62
47.550.853.860.272.979.285.6
104.6142.7
1.001.121.121.371.621.872.122.754.62
25.428.428.434.841.147.553.869.9
117.3
A
B
B B
BPE - Table # DT-15
BPE - Table # DT-22
BPE - Table # DT-9
SIZE A(TUBE O.D.)in. mm in. mm
JTL14AM7 – TANGENT FERRULE
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
1.751.751.751.752.252.252.252.253.00
44.544.544.544.557.257.257.257.276.2
SIZE B(TUBE O.D.)in. mm in. mm
JTL7W – TANGENT TEE
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
1.872.002.122.372.873.123.374.125.62
47.550.853.860.272.979.285.6
104.6142.7
C
BB
A
B
A
35
BIO
PHARM
FITTINGS
SIZE B C(TUBE O.D.)in. mm in. mm in. mm
JTL7RWMS – TANGENT REDUCING TEE SHORT
3⁄4 x 1⁄21 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 1⁄23 x 3⁄43 x 13 x 11⁄23 x 23 x 21⁄24 x 1⁄24 x 3⁄44 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 4
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 12.776.2 x 19.176.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 12.7101.6 x 19.1101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 101.6
2.002.122.122.372.372.372.872.872.872.873.123.123.123.123.123.373.373.373.373.373.374.124.124.124.124.124.124.125.63
50.853.853.860.260.260.272.972.972.972.979.279.279.279.279.285.685.685.685.685.685.6
104.6104.6104.6104.6104.6104.6104.6143.0
1.001.121.121.371.371.371.621.621.621.621.871.871.871.871.872.122.122.122.122.122.122.622.622.622.622.622.622.623.75
25.428.428.434.834.834.841.141.141.141.147.547.547.547.547.553.853.853.853.853.853.866.566.566.566.566.566.566.595.3
BPE - Table # DT-14
BPE - Table # DT-30
A
SIZE A(TUBE O.D.)in. mm in. mm
JTL16W – TANGENT CAP
1⁄23⁄4111⁄2221⁄234
12.719.125.438.150.863.576.2
101.6
1.501.501.502.062.502.812.873.25
38.138.138.152.363.571.472.982.6
B
C
B
36
BIO
PHARM
FITTINGS
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
JTL7RWWM – TANGENT REDUCING TEE LONG
3⁄4 x 1⁄21 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
2.002.122.122.372.372.372.872.872.872.873.123.123.123.373.373.373.374.124.124.124.124.12
50.853.853.860.260.260.272.972.972.972.979.279.279.285.685.685.685.6
104.6104.6104.6104.6104.6
2.502.622.622.872.872.873.123.123.123.123.373.373.373.623.623.623.624.254.254.504.504.50
63.566.566.572.972.972.979.279.279.279.285.685.685.691.991.991.991.9
108.0108.0114.3114.3114.3
SIZE A AA(TUBE O.D.)in. mm in. mm in. mm
JTL7RW v TANGENT REDUCING TEE
3⁄4 x 1⁄21 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 1⁄23 x 3⁄43 x 13 x 11⁄23 x 23 x 21⁄24 x 1⁄24 x 3⁄44 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 4
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 12.776.2 x 19.176.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 12.7101.6 x 19.1101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 101.6
2.002.122.122.372.372.372.872.872.872.873.123.123.123.123.123.373.373.373.373.373.374.124.124.124.124.124.124.125.62
50.853.853.860.260.260.272.972.972.972.979.279.279.279.279.285.685.685.685.685.685.6
104.6104.6104.6104.6104.6104.6104.6142.7
2.002.122.122.372.372.372.622.622.622.622.872.872.872.872.873.123.123.123.123.123.123.623.623.623.623.873.873.875.12
50.853.853.860.260.260.266.566.566.566.572.972.972.972.972.979.279.279.279.279.279.291.991.991.991.998.398.398.3
130.0
BPE - Table # DT-10
B
A
AA
AA
A
37
BIO
PHARM
FITTINGS
SIZE A(TUBE O.D.)in. mm in. mm
JTL31MJTL32M – KWIK CLAMP TANGENT REDUCERS
3⁄4 x 1⁄21 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 4
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 101.6
3.003.503.004.504.004.006.506.006.004.008.508.008.006.004.25
10.008.006.254.25
14.1312.1310.378.376.379.00
76.288.976.2
114.3101.6101.6165.1152.4152.4101.6215.9203.2203.2152.4108.0254.0203.2158.8108.0358.9308.1263.4212.6161.8228.6
SIZE A(TUBE O.D.)in. mm in. mm
JTL31JTL32 – TANGENT REDUCERS
3⁄4 x 1⁄21 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 4
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 101.6
4.004.504.005.505.005.007.757.257.255.259.759.259.257.255.50
11.259.257.505.50
15.5013.5011.759.757.75
10.00
101.6114.3101.6139.7127.0127.0196.9184.2184.2133.4247.7235.0235.0184.2139.7285.8235.0190.5139.7393.7342.9298.5247.7196.9254.0
A
A
BPE - Table # DT-26
A
CB
B
A
C
BPE - Table # DT-11
38
BIO
PHARM
FITTINGS
SIZE E F(TUBE O.D.)in. mm in. mm in. mm
JTL9W – TANGENT CROSS
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
3.754.004.254.755.756.256.758.25
11.25
95.3101.6108.0120.7146.1158.8171.5209.6285.8
1.872.002.122.372.873.123.374.125.62
47.550.853.860.272.979.285.6
104.6142.7
BPE - Table # DT-9
F
E
E
F
39
BIO
PHARM
FITTINGS
TANGENT POINT OF USE
SIZE A B C D E APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm in. mm in. mm
3⁄4 x1⁄2
1 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 1⁄23 x 3⁄43 x 13 x 11⁄23 x 23 x 21⁄24 x 1⁄24 x 3⁄44 x 14 x 11⁄24 x 24 x 21⁄24 x 3
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 12.776.2 x 19.176.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 12.7101.6 x 19.1101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
4.504.504.506.006.006.006.006.006.006.007.507.507.507.507.509.009.009.009.009.009.00
12.0012.0012.0012.0012.0012.0012.00
114.3114.3114.3152.4152.4152.4152.4152.4152.4152.4190.5190.5190.5190.5190.5228.6228.6228.6228.6228.6228.6304.8304.8304.8304.8304.8304.8304.8
2.252.252.253.003.003.003.003.003.003.003.753.753.753.753.754.504.504.504.504.504.506.006.006.006.006.006.006.00
57.257.257.276.276.276.276.276.276.276.295.395.395.395.395.3
114.3114.3114.3114.3114.3114.3152.4152.4152.4152.4152.4152.4152.4
3.003.003.004.504.504.505.005.005.005.005.755.755.755.755.756.506.506.506.506.506.508.508.508.508.508.508.508.50
76.276.276.2
114.3114.3114.3127.0127.0127.0127.0146.1146.1146.1146.1146.1165.1165.1165.1165.1165.1165.1215.9215.9215.9215.9215.9215.9215.9
1.001.131.131.381.381.381.631.631.631.631.881.881.881.881.882.132.132.132.132.132.132.632.632.632.632.632.632.63
25.428.728.735.135.135.141.441.441.441.447.847.847.847.847.854.154.154.154.154.154.166.866.866.866.866.866.866.8
3.133.253.135.004.884.755.755.635.505.256.756.636.506.256.007.757.637.507.257.006.75
10.2510.1310.009.759.509.259.00
79.582.679.5
127.0124.0120.7146.1143.0139.7133.4171.5168.4165.1158.8152.4196.9193.8190.5184.2177.8171.5260.4257.3254.0247.7241.3235.0228.6
0.360.440.450.760.770.801.271.281.311.382.002.002.052.252.353.373.383.413.483.613.716.126.136.166.236.366.166.64
AB
C
JTL2UBO JTL2USO
**Not included ASME BPE.
40
BIO
PHARM
FITTINGS
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
INSTRUMENT TEE
1⁄2 x 11⁄2 BW3⁄4 x 11⁄2 BW1 x 11⁄2 BW1⁄2 x 2 BW3⁄4 x 2 BW1 x 2 BW11⁄2 x 2 BW
1⁄2 x 11⁄2 KC3⁄4 x 11⁄2 KC1 x 11⁄2 KC1⁄2 x 2 KC3⁄4 x 2 KC1 x 2 KC11⁄2 x 2 KC
12.7 x 38.1 BW19.1 x 38.1 BW25.4 x 38.1 BW12.7 x 50.8 BW19.1 x 50.8 BW25.4 x 50.8 BW38.1 x 50.8 BW
12.7 x 38.1 KC19.1 x 38.1 KC25.4 x 38.1 KC12.7 x 50.8 KC19.1 x 50.8 KC25.4 x 50.8 KC38.1 x 50.8 KC
5.005.005.005.505.505.505.50
6.006.006.006.506.506.506.50
127.0127.0127.0139.7139.7139.7139.7
152.4152.4152.4165.1165.1165.1165.1
0.881.001.131.001.131.251.50
0.881.001.131.001.131.251.50
22.425.428.725.428.731.838.1
22.425.428.725.428.731.838.1
Available in PL and PM Finishes only.Not included in ASME BPE.
A
B
A
B
JTL7IWMS
JC7IS
41
BIO
PHARM
FITTINGS
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
JC7 – TEE
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
2.252.372.622.873.373.623.874.757.13
57.260.266.572.985.691.998.3
120.7181.1
4.504.755.255.756.757.257.759.50
14.25
114.3120.7133.4146.1171.5184.2196.9241.3362.0
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
JC7S – SHORT OUTLET TEE
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
2.252.372.622.873.373.623.874.757.13
57.260.266.572.985.691.998.3
120.7181.1
1.001.121.121.371.621.872.122.754.62
25.428.428.434.841.147.553.869.9
117.3
A
A
R
BPE - Table # DT-16
A
A
BPE - Table # DT-17
A
A
B
BPE - Table # DT-18
A A
B
BPE - Table # DT-27
SIZE A(TUBE O.D.)in. mm in. mm
JC2 – 90 ̊ELL
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
1.621.622.002.753.504.255.006.62
10.50
41.141.150.869.988.9
108.0127.0168.1266.7
SIZE B(TUBE O.D.)in. mm in. mm
JC2K – 45 ̊ELL
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
1.001.001.121.441.752.062.383.125.25
25.425.428.436.644.552.360.579.2
133.4
42
BIO
PHARM
FITTINGS
SIZE OVERALL(TUBE O.D.) LENGTH
in. mm in. mm
JC31JC32 – CONCENTRIC REDUCER
3⁄4 x 1⁄21 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 4
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 101.6
2.002.502.003.503.003.005.505.005.003.007.507.007.005.003.009.007.005.003.00
13.1211.129.127.125.127.63
50.863.550.888.976.276.2
139.7127.0127.076.2
190.5177.8177.8127.076.2
228.6177.8127.076.2
333.2282.4231.6180.8130.0193.8
SIZE A B C(TUBE O.D.)in. mm in. mm in. mm in. mm
JC7R – REDUCING TEE
3⁄4 x 1⁄21 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 1⁄23 x 3⁄43 x 13 x 11⁄23 x 23 x 21⁄24 x 1⁄24 x 3⁄44 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 4
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 12.776.2 x 19.176.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 12.7101.6 x 19.1101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 101.6
2.502.622.622.872.872.873.133.133.133.133.383.383.383.383.383.633.633.633.633.883.884.134.134.134.134.384.384.385.75
63.566.566.572.972.972.979.579.579.579.585.985.985.985.985.992.292.292.292.298.698.6
104.9104.9104.9104.9111.3111.3111.3146.1
2.502.622.622.872.872.873.373.373.373.373.633.633.633.633.633.873.873.873.873.873.874.754.754.754.754.754.754.757.13
63.566.566.572.972.972.985.685.685.685.692.292.292.292.292.298.398.398.398.398.398.3
120.7120.7120.7120.7120.7120.7120.7181.1
5.005.255.255.755.755.756.756.756.756.757.257.257.257.257.257.757.757.757.757.757.759.509.509.509.509.509.509.50
14.25
127.0133.4133.4146.1146.1146.1171.5171.5171.5171.5184.2184.2184.2184.2184.2196.9196.9196.9196.9196.9196.9241.3241.3241.3241.3241.3241.3241.3362.0
BPE - Table # DT-21
B
A
C
BPE - Table # DT-19
43
BIO
PHARM
FITTINGS
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
JC7RS – SHORT OUTLET REDUCED TEE
3⁄4 x 1⁄21 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 1⁄23 x 3⁄43 x 13 x 11⁄23 x 23 x 21⁄24 x 1⁄24 x 3⁄44 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 4
19.1 x 12.725.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 12.776.2 x 19.176.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 12.7101.6 x 19.1101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 101.6
2.502.622.622.872.872.873.373.373.373.373.633.633.633.633.633.873.873.873.873.873.874.754.754.754.754.754.754.757.13
63.566.566.572.972.972.985.685.685.685.692.292.292.292.292.298.398.398.398.398.398.3
120.7120.7120.7120.7120.7120.7120.7181.1
1.001.121.121.371.371.371.621.621.621.621.871.871.871.871.872.122.122.122.122.122.122.622.622.622.622.622.622.623.75
25.428.428.434.834.834.841.141.141.141.147.547.547.547.547.553.853.853.853.853.853.866.566.566.566.566.566.566.595.3
A
B
A
BPE - Table # DT-20
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
JC9 – CROSS
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
2.252.372.622.873.373.623.874.757.13
57.260.266.572.985.691.998.3
120.7181.1
4.504.755.255.756.757.257.759.50
14.25
114.3120.7133.4146.1171.5184.2196.9241.3362.0
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
JC16 – SOLID END CAP
1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
0.190.190.250.250.250.250.250.310.44
4.84.86.46.46.46.46.47.9
11.2
0.980.981.981.982.513.043.584.686.57
24.924.950.350.363.877.290.9
118.9166.9
AB
A
B
BPE - Table # DT-18
AB
Available in PL, PM, and Standard Finishes.
44
BIO
PHARM
FITTINGS
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
JC14AHR** – RUBBER HOSE ADAPTER
1⁄2 x 1⁄23⁄4 x 3⁄4
111⁄2221⁄234
12.7 x 12.719.1 x 19.1
25.438.150.863.576.2
101.6
1.501.501.691.692.312.003.093.41
38.138.142.942.958.750.878.586.6
0.530.781.031.532.032.533.034.03
13.519.826.238.951.664.377.0
102.4
SIZE C(TUBE O.D.)in. mm in. mm
JC21** – ADAPTERS
1⁄2 x 1⁄8*1⁄2 x 1⁄4*1⁄2 x 3⁄8*1⁄2 x 1⁄2*1⁄2 x 3⁄4*3⁄4 x 1⁄8*3⁄4 x 1⁄4*3⁄4 x 3⁄8*3⁄4 x 1⁄2*3⁄4 x 3⁄4*
111⁄2221⁄2*34
12.7 x 3.2*12.7 x 6.4*12.7 x 9.5*12.7 x 12.7*12.7 x 19.1*19.1 x 3.2*19.1 x 6.4*19.1 x 9.5*19.1 x 12.7*19.1 x 19.1*
25.438.150.863.5*76.2
101.6
2.002.002.002.002.002.002.002.002.002.002.252.442.663.283.503.81
50.850.850.850.850.850.850.850.850.850.857.262.067.683.388.996.8
SIZE A(TUBE O.D.)in. mm in. mm
JC22** – ADAPTERS
1⁄2 x 1⁄8*1⁄2 x 1⁄4*1⁄2 x 3⁄8*1⁄2 x 1⁄2*1⁄2 x 3⁄4*3⁄4 x 1⁄8*3⁄4 x 1⁄4*3⁄4 x 3⁄8*3⁄4 x 1⁄2*3⁄4 x 3⁄4*
111⁄2221⁄2*34
12.7 x 3.2*12.7 x 6.4*12.7 x 9.5*12.7 x 12.7*12.7 x 19.1*19.1 x 3.2*19.1 x 6.4*19.1 x 9.5*19.1 x 12.7*19.1 x 19.1*
25.438.150.863.5*76.2
101.6
1.251.501.501.501.621.251.501.501.501.621.622.252.342.092.192.66
31.838.138.138.141.131.838.138.138.141.141.157.259.453.155.667.6
C
C
D
D
* NO HEX CENTER** Not included in the ASME BPE standard, therefore, will
be marked with Material grade and heat number only.Available in PL, PM, and Standard Finishes.
A Swagelok Company
Sanitary
Acme Threaded
Fittings
45
46
SANITARY
ACME
THREADED
FITTINGS
Jensen has crafted stainless steel sanitary Acme Threaded fittings since 1959 for the Brewery, Winery,
Beverage, Food, Dairy and Pharmaceutical industries. Dimensions shown in this catalog are to standards
accepted by the industry.
Sanitary fittings, crevice free and smooth bored are made to tube
outside diameter dimensions and should not be confused with
nominal pipe size. To identify existing line sizes measure the
diameter to the outside as your reference.
These union nut assemblies with sanitary Acme threads permit easy assembly and safe fast cleaning of lines.
All welds used in manufacturing are of the Tungsten Inert Gas Method for true fusion of wall with no thinning
or pitting. Fittings with weld ends are manufactured to exact circularity tolerances and have true square butt
ends for on site T.I.G. installation. Availability is in Type 304 & 316L stainless steel.
2F-31 – 90˚ REDUCING ELBOW (Non-Tapered)SIZE A B APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
23⁄16
23⁄16
231⁄32
23⁄16
231⁄32
323⁄32
23⁄16
231⁄32
323⁄32
419⁄32
23⁄16
231⁄32
323⁄32
419⁄32
513⁄32
55.555.575.455.575.494.455.575.494.4
116.755.575.494.4
116.7137.3
21⁄16
21⁄827⁄825⁄32
229⁄32
321⁄32
27⁄32
231⁄32
323⁄32
415⁄32
25⁄16
31⁄16
313⁄16
49⁄16
55⁄16
52.454.073.054.873.892.956.375.494.4
113.558.777.896.8
115.9134.9
0.750.951.201.101.351.451.501.751.952.252.302.452.652.953.50
2F-32 – 90˚ REDUCING ELBOW (Non-Tapered)SIZE A B APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
23⁄16
23⁄16
231⁄32
23⁄16
231⁄32
323⁄32
23⁄16
231⁄32
323⁄32
419⁄32
23⁄16
231⁄32
323⁄32
419⁄32
513⁄32
55.555.575.455.575.494.455.575.494.4
116.755.575.494.4
116.7137.3
21⁄16
21⁄827⁄825⁄32
229⁄32
321⁄32
27⁄32
231⁄32
323⁄32
415⁄32
25⁄16
31⁄16
313⁄16
49⁄16
55⁄16
52.454.073.054.873.892.956.375.494.4
113.558.777.896.8
115.9134.9
0.750.951.201.101.351.451.501.751.952.252.302.452.652.953.50
B
A
B
A
47
SANITARY
ACME
THREADED
FITTINGS
2C – 90˚ SWEEP ELLSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
23⁄16
231⁄32
323⁄32
419⁄32
513⁄32
77⁄32
55.575.494.4
116.7137.3183.3
.30
.621.061.753.005.60
2E – 90˚ SWEEP ELLSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
23⁄16
231⁄32
323⁄32
419⁄32
513⁄32
77⁄32
55.575.494.4
116.7137.3183.3
.851.633.064.757.00
13.60
2F – 90˚ SWEEP ELLSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
23⁄16
231⁄32
323⁄32
419⁄32
513⁄32
77⁄32
55.575.494.4
116.7137.3183.3
.631.381.943.504.819.19
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
2P – 45˚ SWEEP ELL
111⁄2221⁄234
25.438.150.863.576.2
101.6
15⁄16
123⁄32
21⁄825⁄831⁄841⁄4
33.343.654.066.779.4
108.0
21⁄821⁄825⁄16
29⁄16
229⁄32
37⁄8
54.054.058.765.173.898.4
.501.001.692.944.007.56
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
7 – TEE
111⁄2221⁄234
25.438.150.863.576.2
101.6
113⁄16
23⁄8225⁄32
33⁄16
31⁄2421⁄32
46.060.370.680.988.9
118.3
35⁄843⁄459⁄16
63⁄8795⁄16
92.1120.7141.3161.9177.8236.5
.44
.881.382.063.195.00
A
A
A
A
A
A
B
A
AB
A
48
SANITARY
ACME
THREADED
FITTINGS
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
14WF – PLAIN SHORT WELD FERRULE
111⁄2221⁄234
25.438.150.863.576.2
101.6
11⁄1623⁄3223⁄3227⁄3229⁄32
17⁄32
17.418.218.221.423.030.9
111⁄2221⁄234
25.438.150.863.576.2
101.6
0.100.100.200.310.430.69
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
14A – PLAIN TUBE FERRULE
111⁄2221⁄234
25.438.150.863.576.2
101.6
13⁄811⁄211⁄213⁄413⁄413⁄4
34.938.138.144.544.544.5
0.8701.3701.8702.3702.8703.834
22.134.847.560.272.997.4
111⁄2221⁄234
25.438.150.863.576.2
101.6
0.060.250.370.570.690.81
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
14W – PLAIN FERRULE TANK SPUD (Heavy)
111⁄2221⁄234
25.438.150.863.576.2
101.6
23⁄8217⁄32
225⁄32
31⁄16
317⁄32
45⁄16
60.364.370.677.889.7
109.5
0.8701.3701.8702.3702.8703.834
22.134.847.560.272.997.4
15⁄32
143⁄64
23⁄16
245⁄64
37⁄32
41⁄4
29.442.455.568.781.7
108.0
0.340.500.821.252.633.45
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
14WL – PLAIN FERRULE TANK SPUD (Light)
111⁄2221⁄234
25.438.150.863.576.2
101.6
221⁄421⁄223⁄434
50.857.263.569.976.2
101.6
0.8701.3701.8702.3702.8703.834
22.134.847.560.272.997.4
111⁄2221⁄234
25.438.150.863.576.2
101.6
0.090.190.380.540.781.24
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
15A – THREADED TUBE FERRULE
111⁄2221⁄234
25.438.150.863.576.2
101.6
13⁄811⁄211⁄213⁄413⁄413⁄4
34.938.138.144.544.544.5
0.8701.3701.8702.3702.8703.834
22.134.847.560.272.997.4
111⁄2221⁄234
25.438.150.863.576.2
101.6
0.090.290.380.630.871.29
B
A
B
A
C
B
A
C
B
A
C
A
B C
49
SANITARY
ACME
THREADED
FITTINGS
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
15WF – THREADED SHORT WELD FERRULE
111⁄2221⁄234
25.438.150.863.576.2
101.6
11⁄1623⁄3223⁄3227⁄3229⁄32
17⁄32
17.418.218.221.423.030.9
111⁄2221⁄234
25.438.150.863.576.2
101.6
0.150.150.290.450.621.15
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
15W – THREADED FERRULE TANK SPUD (Heavy)
111⁄2221⁄234
25.438.150.863.576.2
101.6
11⁄215⁄813⁄413⁄4113⁄16
21⁄8
38.141.344.544.546.054.0
0.8701.3701.8702.3702.8703.834
22.134.847.560.272.997.4
11⁄413⁄425⁄16
27⁄833⁄841⁄4
31.844.558.773.085.7
108.0
0.170.350.691.001.402.50
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
15WL – THREADED FERRULE TANK SPUD (Light)
111⁄2221⁄234
25.438.150.863.576.2
101.6
221⁄421⁄223⁄434
50.857.263.569.976.2
101.6
0.8701.3701.8702.3702.8703.834
22.134.847.560.272.997.4
111⁄2221⁄234
25.438.150.863.576.2
101.6
0.120.250.490.701.001.75
SIZE A C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
14AHR – RUBBER HOSE ADAPTER*
111⁄2221⁄234
25.438.150.863.576.2
101.6
111⁄16
111⁄16
25⁄16
211⁄32
31⁄24
42.842.858.759.588.9
101.6
11⁄32
117⁄32
21⁄32
217⁄32
31⁄32
41⁄32
26.238.951.664.377.0
102.4
0.140.260.530.801.121.54
SIZE A B(TUBE O.D.)in. mm in. mm in. mm
16AT*
111⁄2221⁄234
25.438.150.863.576.2
101.6
11⁄411⁄419⁄32
***
31.831.832.5***
2225⁄8***
50.850.866.7***
* Note: 21⁄2“ - 4” (63.5 - 101.6mm) (Round O.D.) available on request.
*May be furnished in reducing sizes.
A
B
A
B C
A
B C
A B
Y FILLA
C
50
SANITARY
ACME
THREADED
FITTINGS
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
14AHT – TYGON HOSE ADAPTER*
111⁄2221⁄234
25.438.150.863.576.2
101.6
411⁄16
423⁄32
423⁄32
427⁄32
429⁄32
57⁄32
119.0119.8119.8123.0124.6132.5
111⁄2221⁄234
25.438.150.863.576.2
101.6
0.310.500.680.871.121.68
B
A
A
C
B
A
A
SIZE A C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
15AHR – RUBBER HOSE ADAPTER*
111⁄2221⁄234
25.438.150.863.576.2
101.6
111⁄16
111⁄16
25⁄16
211⁄32
31⁄24
42.842.858.759.588.9
101.6
11⁄32
117⁄32
21⁄32
217⁄32
31⁄32
41⁄32
26.238.951.664.377.0
102.4
0.170.320.640.961.342.05
*May be furnished in reducing sizes.
*May be furnished in reducing sizes.
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
15AHT – TYGON HOSE ADAPTER*
111⁄2221⁄234
25.438.150.863.576.2
101.6
411⁄16
423⁄32
423⁄32
427⁄32
429⁄32
57⁄32
119.0119.8119.8123.0124.6132.5
111⁄2221⁄234
25.438.150.863.576.2
101.6
0.340.560.791.031.342.19
*May be furnished in reducing sizes.
31TP – TAPER REDUCER
SIZE A APPROX.WT. LBS.
in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
411⁄32
611⁄32
47⁄16
815⁄32
69⁄16
43⁄41017⁄32
85⁄8613⁄16
51⁄16
1427⁄32
1215⁄16
111⁄893⁄8717⁄32
110.3161.1112.7215.1166.7120.7267.5219.1173.0128.6377.0328.6282.6238.1191.3
0.721.051.201.351.611.651.992.232.242.542.722.913.954.354.61
51
SANITARY
ACME
THREADED
FITTINGS
31TT – TAPER REDUCER
SIZE A APPROX.WT. LBS.
in. mm in. mm
SIZE A APPROX.WT. LBS.
in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.1
313⁄32
513⁄32
37⁄16
717⁄32
59⁄16
39⁄16
919⁄32
75⁄8
86.5137.387.3
191.3141.390.5
243.7193.7
0.440.770.690.901.101.031.711.72
3 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
55⁄833⁄41329⁄32
1115⁄16
915⁄16
81⁄16
61⁄8
142.995.3
353.2303.2252.4204.8155.6
1.461.362.442.403.173.172.94
31-14F – CONCENTRIC TAPER REDUCER
SIZE A APPROX.WT. LBS.
in. mm in. mm
SIZE A APPROX.WT. LBS.
in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.1
411⁄32
611⁄32
47⁄16
815⁄32
69⁄16
43⁄41017⁄32
85⁄8
110.3161.1112.7215.1166.7120.7267.5219.1
1.111.771.921.802.652.853.503.74
3 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
613⁄16
51⁄16
1427⁄32
1215⁄16
111⁄893⁄8717⁄32
173.0128.6377.0328.6282.6238.1191.3
3.754.055.585.776.817.217.47
31-15F – CONCENTRIC TAPER REDUCER
SIZE A APPROX.WT. LBS.
in. mm in. mm
SIZE A APPROX.WT. LBS.
in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.1
313⁄32
513⁄32
37⁄16
717⁄32
59⁄16
39⁄16
919⁄32
75⁄8
86.5137.387.3
191.3141.390.5
243.7193.7
0.390.710.630.850.940.871.521.53
3 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
55⁄833⁄41329⁄32
1115⁄16
915⁄16
81⁄16
61⁄8
142.995.3
353.2303.2252.4204.8155.6
1.271.172.052.012.782.782.55
32TT – ECCENTRIC TAPER REDUCER
SIZE A APPROX.WT. LBS.
in. mm in. mm
SIZE A APPROX.WT. LBS.
in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.1
313⁄32
513⁄32
37⁄16
717⁄32
59⁄16
39⁄16
919⁄32
75⁄8
86.5137.387.3
191.3141.390.5
243.7193.7
0.440.770.691.251.101.031.711.72
3 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
55⁄833⁄41329⁄32
1115⁄16
915⁄16
81⁄16
61⁄8
142.995.3
353.2303.2252.4204.8155.6
1.461.362.442.403.173.172.94
A
A
A
A
52
SANITARY
ACME
THREADED
FITTINGS
32TP – ECCENTRIC REDUCER
SIZE A APPROX.WT. LBS.
in. mm in. mm
SIZE A APPROX.WT. LBS.
in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.1
411⁄32
611⁄32
47⁄16
815⁄32
69⁄16
43⁄41017⁄32
85⁄8
110.3161.1112.7215.1166.7120.7267.5219.1
0.721.051.201.551.611.651.992.23
3 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
613⁄16
51⁄16
1427⁄32
1215⁄16
111⁄893⁄8717⁄32
173.0128.6377.0328.6282.6238.1191.3
2.242.542.722.913.954.354.61
32-14F – ECCENTRIC REDUCER
SIZE A APPROX.WT. LBS.
in. mm in. mm
SIZE A APPROX.WT. LBS.
in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.1
411⁄32
611⁄32
47⁄16
815⁄32
69⁄16
43⁄41017⁄32
85⁄8
110.3161.1112.7215.1166.7120.7267.5219.1
1.111.771.922.302.652.853.503.74
3 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
613⁄16
51⁄16
1427⁄32
1215⁄16
111⁄893⁄8717⁄32
173.0128.6377.0328.6282.6238.1191.3
3.754.055.585.776.817.217.47
32-15F – ECCENTRIC REDUCER
SIZE A APPROX.WT. LBS.
in. mm in. mm
SIZE A APPROX.WT. LBS.
in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.1
313⁄32
513⁄32
37⁄16
717⁄32
59⁄16
39⁄16
919⁄32
75⁄8
86.5137.3
87.3191.3141.390.5
243.7193.7
0.390.710.630.850.940.871.521.53
3 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
76.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
55⁄833⁄41329⁄32
1115⁄16
915⁄16
81⁄16
61⁄8
142.995.3
353.2303.2252.4204.8155.6
1.271.172.052.012.782.782.55
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
7A – TEE
111⁄2221⁄234
25.438.150.863.576.2
101.6
113⁄16
23⁄8225⁄32
33⁄16
31⁄2421⁄32
46.060.370.680.988.9
118.3
35⁄843⁄459⁄16
63⁄8795⁄16
92.1120.7141.3161.9177.8236.5
211⁄16
313⁄32
313⁄16
41⁄445⁄861⁄8
68.286.596.8
108.0117.5155.6
0.921.572.693.915.209.54
A
A
C
AB
53
SANITARY
ACME
THREADED
FITTINGS
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
7B – TEE
111⁄2221⁄234
25.438.150.863.576.2
101.6
113⁄16
23⁄8225⁄32
33⁄16
31⁄2421⁄32
46.060.370.680.988.9
118.3
211⁄16
313⁄32
313⁄16
41⁄445⁄861⁄8
68.286.596.8
108.0117.5155.6
41⁄2525⁄32
619⁄32
77⁄16
81⁄81025⁄32
114.3146.8167.5188.9206.4273.8
0.921.572.693.915.209.54
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
7X – TEE
111⁄2221⁄234
25.438.150.863.576.2
101.6
227⁄8323⁄32
427⁄32
529⁄32
81⁄16
50.873.094.4
123.0150.0204.8
453⁄477⁄16
911⁄16
1113⁄16
161⁄8
101.6146.1188.9246.0300.0409.6
0.641.061.912.733.536.49
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
7A – TEE
111⁄2221⁄234
25.438.150.863.576.2
101.6
227⁄8323⁄32
427⁄32
529⁄32
81⁄16
50.873.094.4
123.0150.0204.8
453⁄477⁄16
911⁄16
1113⁄16
161⁄8
101.6146.1188.9246.0300.0409.6
227⁄8323⁄32
427⁄32
529⁄32
81⁄16
50.873.094.4
123.0150.0204.8
0.901.502.633.775.049.35
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
7BX – TEE
111⁄2221⁄234
25.438.150.863.576.2
101.6
227⁄8323⁄32
427⁄32
529⁄32
81⁄16
50.873.094.4
123.0150.0204.8
227⁄8323⁄32
427⁄32
529⁄32
81⁄16
50.873.094.4
123.0150.0204.8
453⁄477⁄16
911⁄16
1113⁄16
161⁄8
101.6146.1188.9246.0300.0409.6
0.901.502.633.775.049.35
CB
A
A
BA
A
AB
C
CB
A
A
54
SANITARY
ACME
THREADED
FITTINGS
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
9 – CROSS
111⁄2221⁄234
25.438.150.863.576.2
101.6
113⁄16
23⁄8225⁄32
33⁄16
31⁄2421⁄32
46.060.370.680.988.9
118.3
35⁄843⁄459⁄16
63⁄8795⁄16
92.1120.7141.3161.9177.8236.5
0.811.403.143.884.478.20
SIZE A B C D APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm in. mm
9A – CROSS
111⁄2221⁄234
25.438.150.863.576.2
101.6
113⁄16
23⁄8225⁄32
33⁄16
31⁄2421⁄32
46.060.370.680.988.9
118.3
35⁄843⁄459⁄16
63⁄8795⁄16
92.1120.7141.3161.9177.8236.5
41⁄2525⁄32
619⁄32
77⁄16
81⁄81025⁄32
114.3146.8167.5188.9206.4273.8
211⁄16
313⁄32
313⁄16
41⁄445⁄861⁄8
68.286.596.8
108.0117.5155.6
1.091.913.925.066.14
11.25
28B – TRUE YSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
311⁄16
323⁄32
423⁄32
527⁄32
629⁄32
97⁄32
93.694.4
119.9148.4175.4234.1
0.901.433.073.294.247.61
SIZE A B C APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
28A – LATERAL
111⁄2221⁄234
25.438.150.863.576.2
101.6
45⁄853⁄861⁄875⁄891⁄2113⁄4
117.5136.5155.6193.7241.3298.5
45⁄16
51⁄16
51⁄267⁄881⁄410
109.5128.6139.7174.6209.6254.0
11⁄413⁄815⁄821⁄821⁄23
31.834.941.354.063.576.2
0.911.552.563.864.699.85
AB
A
B
D
B
C
A
A
A
A
A
B
AC
55
SANITARY
ACME
THREADED
FITTINGS
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
16A – PLAIN CAP23B – THREADED CAP
111⁄2221⁄234
25.438.150.863.576.2
101.6
15⁄16
127⁄32
23⁄8229⁄32
37⁄16
41⁄2
33.346.860.373.887.3
114.3
15⁄329⁄165⁄821⁄3223⁄3213⁄16
11.914.315.916.718.220.6
0.120.300.650.901.903.10
SIZE A B APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
13H – HEX UNION NUT
111⁄2221⁄234
25.438.150.863.576.2
101.6
29⁄3231⁄32
11⁄16
13⁄16
19⁄32
11⁄2
23.024.627.030.132.538.1
113⁄16
213⁄32
3319⁄32
43⁄16
57⁄16
46.061.176.291.3
106.3138.1
0.250.440.751.251.813.63
SIZEin.
J40NH — BUNA
111⁄2221⁄234
SIZEin.
J40T — TEFLON
111⁄2221⁄234
A
B
A B
B
A
16APlain
23BTapped
Thermometer Cap(1" tapped 1/2" NPT;others tapped 3/4")
56
SANITARY
ACME
THREADED
FITTINGS
21 AND 22 ADAPTERS
A C APPROX. APPROX.WT. LBS. WT. LBS.
in. mm in. mm in. mm
1 x 3⁄41 x 111⁄2 x 11⁄411⁄2 x 11⁄22 x 11⁄22 x 221⁄2 x 221⁄2 x 21⁄23 x 34 x 4
25.4 x 19.125.4 x 25.438.1 x 31.838.1 x 38.150.8 x 38.150.8 x 50.863.5 x 50.863.5 x 63.576.2 x 76.2101.6 x 101.6
23⁄16
21⁄427⁄16
27⁄16
215⁄32
221⁄32
225⁄32
39⁄32
31⁄2313⁄16
55.557.261.961.962.767.570.683.388.996.8
15⁄821⁄16
21⁄221⁄4121⁄32
211⁄32
127⁄32
23⁄32
23⁄16
25⁄8
41.352.463.557.242.159.546.853.255.566.7
.48
.50
.64
.66
.961.121.251.812.753.75
.36
.38
.971.001.161.441.562.122.884.12
NO. 21 NO. 22 NO. 21 NO. 22
14-18 – ADAPTERS(Acme Hex Union to Female N.P.T.)
SIZE A APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
23⁄4213⁄16
31⁄439⁄16
445⁄16
69.971.482.690.5
101.6109.5
0.751.252.003.005.507.25
14-19 – ADAPTERS(Acme Hex Union to Male N.P.T.)
SIZE A APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
31⁄831⁄435⁄16
441⁄445⁄16
79.482.684.1
101.6108.0109.5
0.751.252.003.004.757.60
MALE NPTACMETHREAD
A
FEMALE NPT
ACME THREAD
C
A
A
No.21
No.22
SIZE(TUBE O.D.)
NOTE: 1⁄2 — 3⁄4 and 21⁄2 — No hex centers
57
SANITARY
ACME
THREADED
FITTINGS
Available in any desired length (specify on order)
SIZE NO. 17C NOS. 17D & 17EMINIMUM LENGTH MINIMUM LENGTH
in. mm in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
13⁄817⁄16
17⁄16
111⁄16
113⁄16
27⁄16
34.936.536.542.846.061.9
27⁄831⁄833⁄833⁄437⁄845⁄8
73.079.485.795.398.4
117.5
Available in any desired length (specify on order)
SIZE NO. 17F & 17G NOS. 17H & 17KMINIMUM LENGTH MINIMUM LENGTH
in. mm in. mm in. mm
11⁄2 x 12 x 12 x 11⁄211⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.138.1 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
13⁄817⁄16
115⁄32
115⁄32
11⁄211⁄2117⁄32
19⁄16
19⁄16
111⁄16
15⁄8121⁄32
121⁄32
125⁄32
127⁄32
34.936.537.337.338.138.138.939.739.742.841.342.142.145.246.8
33⁄32
39⁄32
33⁄839⁄16
321⁄32
321⁄32
325⁄32
37⁄837⁄8329⁄32
49⁄32
43⁄843⁄8
413⁄32
47⁄16
78.683.385.790.592.992.996.098.498.499.2108.7111.1111.1111.9112.7
TUBE ASSEMBLIES
SIZE A
in. mm in. mm
151 – HEX BLIND CAP (c/w chain)
111⁄2221⁄234
25.438.150.863.576.2
101.6
111⁄16
11⁄811⁄411⁄411⁄2
25.427.028.631.831.838.1
SIZE APPROX.WT. LBS.
in. mm
25H – ALUMINUM WRENCH
111⁄2221⁄234
25.438.150.863.576.2
101.6
0.751.251.502.002.753.50
No. 17C (3A)
No. 17D (3A)
No. 17E (3A)
No. 17F (3A)
No. 17G (3A) No. 17H (3A) No. 17K (3A)
Threaded Ferrule Threaded Ferrule
Threaded Ferrule Plain Ferrule withunion nut
Plain Ferrule with Plain Ferrule withunion nut union nut
Threaded Ferrule Concentric reducerwithout union nut
Threaded Ferrule Eccentric reducerwithout union nut
Plain Ferrule with Concentric reducerunion nut with union nut
Plain Ferrule with Concentric reducerunion nut with union nut
A
Jensen
58
SANITARY
ACME
THREADED
FITTINGS
31-18F – TAPER REDUCER-ADAPTERSanitary Plain Ferrule with Hex Nut to Female N.P.T.
SIZE A APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 11⁄221⁄2 x 23 x 23 x 21⁄24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.163.5 x 50.876.2 x 50.876.2 x 63.5
101.6 x 63.5101.6 x 76.2
43⁄32
63⁄32
43⁄32
65⁄32
419⁄32
621⁄32
423⁄32
91⁄32
715⁄32
104.0154.8104.0156.4116.7169.1119.8229.4189.7
1.522.122.102.752.803.664.607.758.75
31-19F – TAPER REDUCER-ADAPTERSanitary Plain Ferrule to Male N.P.T.
SIZE A APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 11⁄2
*21⁄2 x 23 x 2
*3 x 21⁄24 x 21⁄24 x 3
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.163.5 x 50.876.2 x 50.876.2 x 63.5
101.6 x 63.5101.6 x 76.2
415⁄32
615⁄32
415⁄32
619⁄32
421⁄32
623⁄32
55⁄32
915⁄32
723⁄32
113.5164.3113.5167.5118.3170.6131.0240.5196.0
0.771.051.061.34
*2.511.71
*3.603.513.96
*Hex Nuts supplied on these sizes only
SIZE S T U APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
14AHRB – RUBBER HOSE ADAPTERLONG BREWERY STYLE
111⁄2221⁄234
25.438.150.863.576.2
101.6
31⁄231⁄241⁄241⁄241⁄261⁄4
88.988.9
114.3114.3114.3158.8
13⁄16
15⁄16
113⁄16
25⁄16
213⁄16
413⁄16
20.633.346.058.771.4
122.2
11⁄32
15⁄821⁄825⁄831⁄841⁄8
26.241.354.066.779.4
104.8
0.350.450.951.251.752.75
SIZE S T U APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm in. mm
15AHRB – RUBBER HOSE ADAPTERLONG BREWERY STYLE
111⁄2221⁄234
25.438.150.863.576.2
101.6
31⁄231⁄241⁄241⁄241⁄261⁄4
88.988.9
114.3114.3114.3158.8
13⁄16
15⁄16
113⁄16
25⁄16
213⁄16
413⁄16
20.633.346.058.771.4
122.2
11⁄32
15⁄821⁄825⁄831⁄841⁄8
26.241.354.066.779.4
104.8
0.350.450.951.251.752.75
A
STD. PIPETHRD.
A
T U
S
UT
S
A Swagelok Company
Tube OD Unpolished
Butt Weld
Fittings
59
60
TUBE
OD
UNPOLISHED
BUTT
WELD
FITTINGS
J2SX – 90˚ ELLSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
11⁄221⁄4333⁄441⁄269
38.157.276.295.3
114.3152.4228.6
.13
.29
.52
.871.532.858.53
J2KSX – 45˚ ELLSIZE H APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
5⁄815⁄16
11⁄419⁄16
17⁄821⁄233⁄4
15.923.831.839.747.663.595.3
0.080.150.260.440.771.434.26
SIZE E F APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
J7W – TEE
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
33⁄441⁄26661⁄273⁄410
95.3114.3152.4152.4165.1196.9254.0
17⁄821⁄43331⁄437⁄85
47.657.276.276.282.698.4
127.0
.28
.46
.981.321.762.898.00
SIZE E F APPROX.(TUBE O.D.) WT. LBS.in. mm in. mm in. mm
J9W – CROSS
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
33⁄441⁄26661⁄273⁄410
95.3114.3152.4152.4165.1196.9254.0
17⁄821⁄43331⁄437⁄85
47.657.276.276.282.698.4
127.0
0.330.601.381.902.113.409.50
A
H
F
F
E
F
E
E
F
61
TUBE
OD
UNPOLISHED
BUTT
WELD
FITTINGS
SIZE D E F APPROX.C X B WT. LBS.in. mm in. mm in. mm in. mm
J7WR – REDUCING TEE
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 X 36 X 4
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 76.2152.4 x 76.2
21⁄43333331⁄431⁄431⁄431⁄437⁄837⁄837⁄837⁄837⁄855
57.276.276.276.276.276.282.682.682.682.698.498.498.498.498.4
127.0127.0
41⁄26666661⁄261⁄261⁄261⁄273⁄473⁄473⁄473⁄473⁄41010
114.3152.4152.4152.4152.4152.4165.1165.1165.1165.1196.9196.9196.9196.9196.9254.0254.0
21⁄823⁄821⁄223⁄423⁄431⁄431⁄8331⁄231⁄435⁄835⁄8433⁄433⁄443⁄447⁄8
54.060.363.569.969.982.679.476.288.982.692.192.1
101.695.395.3
120.7123.8
0.500.850.901.101.151.201.401.401.501.402.402.502.602.502.756.006.20
SIZE D E F G APPROX.C X B WT. LBS.in. mm in. mm in. mm in. mm in. mm
J9WR – REDUCING CROSS
11⁄2 x 12 x 12 x 11⁄221⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 23 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 36 x 4
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 76.2152.4 x 76.2
41⁄26666661⁄261⁄261⁄261⁄273⁄473⁄473⁄473⁄473⁄41010
114.3152.4152.4152.4152.4152.4165.1165.1165.1165.1196.9196.9196.9196.9196.9254.0254.0
21⁄43333331⁄431⁄431⁄431⁄437⁄837⁄837⁄837⁄837⁄855
57.276.276.276.276.276.282.682.682.682.698.498.498.498.498.4
127.0127.0
21⁄823⁄821⁄223⁄423⁄431⁄431⁄8331⁄231⁄435⁄835⁄8433⁄433⁄443⁄447⁄8
54.060.363.569.969.982.679.476.288.982.692.192.1
101.695.395.3
120.7123.8
41⁄443⁄4551⁄251⁄261⁄261⁄46761⁄271⁄471⁄4871⁄271⁄291⁄293⁄4
108.0120.7127.0139.7139.7165.1158.8152.4177.8165.1184.2184.2203.2190.5190.5241.3247.7
0.580.931.021.201.301.341.481.531.671.602.482.632.772.703.006.256.70
C
B
D
E
F
C G
F
F
DD
E
B
62
TUBE
OD
UNPOLISHED
BUTT
WELD
FITTINGS
J31W – CONCENTRIC REDUCER
B X C A APPROX.WT. LBS.
in. mm in. mm
B X C A APPROX.WT. LBS.
in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.8
24242864
50.8101.650.8
101.650.8
203.2152.4101.6
0.120.340.180.430.251.000.930.56
3 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 36 x 4
76.2 x 63.5101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 76.2152.4 x 101.6
2121086464
50.8304.8254.0203.2152.4101.6152.4101.6
0.301.121.801.661.501.152.601.92
J32W – ECCENTRIC REDUCER
B X C A APPROX.WT. LBS.
in. mm in. mm
B X C A APPROX.WT. LBS.
in. mm in. mm
11⁄2 x 12 x 12 x 11⁄221⁄2 x 11⁄221⁄2 x 23 x 13 x 11⁄23 x 2
38.1 x 25.450.8 x 25.450.8 x 38.163.5 x 38.163.5 x 50.876.2 x 25.476.2 x 38.176.2 x 50.8
24242864
50.8101.650.8
101.650.8
203.2152.4101.6
0.120.340.180.430.251.000.930.56
3 x 21⁄24 x 14 x 11⁄24 x 24 x 21⁄24 x 36 x 36 x 4
76.2 x 63.5101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2152.4 x 76.2152.4 x 101.6
2121086464
50.8304.8254.0203.2152.4101.6152.4101.6
0.301.121.801.661.501.152.601.92
J19W – ADAPTERSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
13⁄413⁄4113⁄16
25⁄16
21⁄229⁄16
44.544.546.058.763.565.1
0.500.600.751.202.002.60
May be furnished in reducing sizes.
26EF – ADAPTERSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
13⁄815⁄16
13⁄4113⁄16
21⁄423⁄8
34.933.344.546.057.260.3
0.750.801.002.203.505.40
May be furnished in reducing sizes.
A
B C
A
B C
63
TUBE
OD
UNPOLISHED
BUTT
WELD
FITTINGS
J28BW – TRUE YSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm1⁄23⁄4111⁄2221⁄2346
12.719.125.438.150.863.576.2
101.6152.4
223345688
50.850.876.276.2
101.6127.0152.4203.2203.2
0.220.340.540.831.541.882.474.01
11.44
A
A
SIZE A B C NOM.WALL(TUBE O.D.) THICKNESSin. mm in. mm in. mm in. mm
J28WA – LATERAL YAND REDUCING LATERAL Y
1⁄23⁄4111⁄2221⁄23461 x 1⁄21 x 3⁄411⁄2 x 1⁄211⁄2 x 3⁄411⁄2 x 12 x 1⁄22 x 3⁄42 x 12 x 11⁄221⁄2 x 1⁄221⁄2 x 3⁄421⁄2 x 121⁄2 x 11⁄221⁄2 x 23 x 1⁄23 x 3⁄43 x 13 x 11⁄23 x 23 x 21⁄24 x 1⁄24 x 3⁄44 x 14 x 11⁄24 x 24 x 21⁄24 x 3
12.719.125.438.150.863.576.2
101.6152.425.4 x 12.725.4 x 19.138.1 x 12.738.1 x 19.138.1 x 25.450.8 x 12.750.8 x 19.150.8 x 25.450.8 x 38.163.5 x 12.763.5 x 19.163.5 x 25.463.5 x 38.163.5 x 50.876.2 x 12.776.2 x 19.176.2 x 25.476.2 x 38.176.2 x 50.876.2 x 63.5
101.6 x 12.7101.6 x 19.1101.6 x 25.4101.6 x 38.1101.6 x 50.8101.6 x 63.5101.6 x 76.2
66673⁄883⁄410103⁄41213⁄16
161⁄26673⁄873⁄873⁄883⁄483⁄483⁄483⁄41010101010103⁄4103⁄4103⁄4103⁄4103⁄4103⁄41213⁄16
1213⁄16
1213⁄16
1213⁄16
1213⁄16
1213⁄16
1213⁄16
152.4152.4152.4187.3222.3254.0273.1325.4419.1152.4152.4187.3187.3187.3222.3222.3222.3222.3254.0254.0254.0254.0254.0273.1273.1273.1273.1273.1273.1325.4325.4325.4325.4325.4325.4325.4
55563⁄16
71⁄881⁄287⁄8103⁄4121⁄25563⁄16
63⁄16
63⁄16
71⁄871⁄871⁄871⁄881⁄281⁄281⁄281⁄281⁄287⁄887⁄887⁄887⁄887⁄887⁄8103⁄4103⁄4103⁄4103⁄4103⁄4103⁄4103⁄4
127.0127.0127.0157.1181.0215.9225.4273.1317.5127.0127.0157.1157.1157.1181.0181.0181.0181.0215.9215.9215.9215.9215.9225.4225.4225.4225.4225.4225.4273.1273.1273.1273.1273.1273.1273.1
11113⁄16
15⁄811⁄217⁄821⁄16
41113⁄16
13⁄16
13⁄16
15⁄815⁄815⁄815⁄811⁄211⁄211⁄211⁄211⁄217⁄817⁄817⁄817⁄817⁄817⁄821⁄16
21⁄16
21⁄16
21⁄16
21⁄16
21⁄16
21⁄16
25.425.425.430.141.338.147.652.4
101.625.425.430.130.130.141.341.341.341.338.138.138.138.138.147.647.647.647.647.647.652.452.452.452.452.452.452.4
.065
.065
.065
.065
.065
.065
.065
.083
.109
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.065
.083
.083
.083
.083
.083
.083
.083
B
CA
64
TUBE
OD
UNPOLISHED
BUTT
WELD
FITTINGS
SIZE D I.D. A B C T(TUBE O.D.)in. mm in. mm in. mm in. mm in. mm in. mm in. mm
J38W – WELD NECK LIGHT-TYPE FLANGE
111⁄2221⁄2346
25.438.150.863.576.2
101.6152.4
41⁄456771⁄2911
108.0127.0152.4177.8190.5228.6279.4
7⁄813⁄817⁄823⁄827⁄8327⁄32
525⁄32
22.234.947.660.373.097.6
146.8
4444488
101.6101.6101.6101.6101.6203.2203.2
31⁄837⁄843⁄451⁄2671⁄291⁄2
79.498.4
120.7139.7152.4190.5241.3
3⁄83⁄87⁄161⁄21⁄21⁄21⁄2
9.59.5
11.112.712.712.712.7
5⁄85⁄83⁄43⁄43⁄43⁄47⁄8
15.915.919.119.119.119.122.2
J16W – BUTT WELD CAPSIZE A APPROX.(TUBE O.D.) WT. LBS.
in. mm in. mm
111⁄2221⁄234
25.438.150.863.576.2
101.6
7⁄169⁄163⁄411⁄16
11⁄811⁄4
11.114.319.127.028.631.8
0.050.090.250.290.330.56
A
TUBE O.D. BUTT WELD FITTINGS304 or 316L IN STOCK
Jensen stocks a full range of O.D. Tube, unpolished fittings, in 304 or 316L
A Swagelok Company
Miscellaneous
Flow
Components
65
Manual Butterfly Valves
FeaturesTwo Handle Options—MP: Multi-Position
2P: Two-Position
� Available in 304 SS and 316L SS.
� Sizes available include 1 to 4 in. OD.
� Seal material is silicone.
� Maximum temperature is 250°F (121°C) based on sealmaterial manufacturer’s rating.
FeaturesThe following information is applicable to all butterfly valves, either manual or air-actuated:
Ordering Number
EndConnection
Size
Kwik-Clamp
A A B C D E
Dimensions, in. (mm)
1 in. 2 33/64(63.9)
1 37/64(40.1)
3 27/64(86.9)
5 29/32(150)
3 35/64(90.1)
3 35/64(90.1)
1 1/2 in.
2 in.
2 1/2 in.
3 in.
4 in.
3(76.2)
4 3/32(104)
1 31/32(50.0)
2 33/64(63.9)
3 53/64(97.2)
4 21/64(110)
5(127)
5 19/32(142)
6 3/8(162)
3 47/64(94.8)
3 31/32(101)
4 21/64(110)
4 39/64(117)
5 3/64(128)
3 3/4(95.2)
4 1/16(103)
4 11/32(110)
4 41/64(118)
5 1/32(128)
AJC10B 7 15 H 4 15 MP
Hand Operated
Handle TypeMP = Multi-Position2P = Two-Position
Material Grade4 = 304 SS6 = 316L SS
Item CodeAJC10B = Kwik-Clamp ConnectionAJ10B = Tube Butt Weld Connection
End Connection Size10 = 1 in.15 = 1 1/2 in.20 = 2 in.25 = 2 1/2 in.30 = 3 in.40 = 4 in.
End Connection Size10 = 1 in.15 = 1 1/2 in.20 = 2 in.25 = 2 1/2 in.30 = 3 in.40 = 4 in.
2 53/64(71.8)
Polish
Dimensions are for referenceonly, and are subject to change.
WallThickness
Tube Butt Weld
0.065(1.6)
0.083(2.1)
� Maximum pressure is 145 psig (10 bar) on 1 to 3 in.and 115 psig (7.9 bar) on 4 in.
� Kwik-Clamp and tube butt weld connections.
� Acme threaded ends available upon request.
Dimensions
C
D
A
E
B
C
Two-PositionHandle
Multiple-PositionHandle
66
MISCELLANEOUS
FLOW
COMPONENTS
67
MISCELLANEOUS
FLOW
COMPONENTS
Air-Actuated Butterfly Valves
� Normally closed and double-acting actuators
� External switch options and control tops are available.
End Connection Size10 = 1 in.15 = 1 1/2 in.20 = 2 in.25 = 2 1/2 in.30 = 3 in.40 = 4 in.
Ordering Number AJC10B-7-4-20-20
Polish
Actuator Type20 = Normally closed30 = Double-acting
Material Grade4 = 304 SS6 = 316L SS
EndConnection
Size
Kwik-Clamp
A A B C
Dimensions, in. (mm)
1 in. 2 33/64(63.9)
1 37/64(40.1)
3 27/64(86.9)
9 11/64(233)
1 1/2 in.
2 in.
2 1/2 in.
3 in.
4 in.
3(76.2)
4 3/32(104)
1 31/32(50.0)
2 33/64(63.9)
3 53/64(97.2)
4 21/64(110)
5(127)
5 19/32(142)
6 3/8(162)
2 53/64(71.8)
9 3/8(238)
9 41/64(245)
9 23/32(247)
10(254)
10 43/64(271)
Dimensions
Dimensions, in inches (millimeters), are for reference only, andare subject to change.
A B
C3 25/32(96.0)
Tube Butt Weld
WallThickness
0.065(1.6)
0.083(2.1)
Item CodeAJC10B = Kwik-Clamp ConnectionAJ10B = Tube Butt Weld Connection
EndConnection
SizeA
ClampA
Threaded
Dimensions, in. (mm)
1/2 in. 4 5/16(110)
—3/4 in.
1 in.
1 1/2 in.
2 in.
2 1/2 in. 6 17/64(159)
7 61/64(202)
3 in.
4 in.
5 1/8(130)
5 1/16(129)
6 1/8(156)
6 15/16(176)
6 1/2(165)
6 9/16(167)
6 1/2(165)
7 15/16(202)
9 3/8(238)
Vertical Disk Check Valves
FeaturesPurpose: Prevention of product backflow for vertical applications
� Produced from 304 SS or 316L SS
� Available in the following sizes:Kwik-Clamp (45HC)—1/2 to 4 in.Acme Threaded (45H)—1 to 4 in.
� Standard body seal material is Buna. Other seal materialsavailable.
� Tube butt weld ends available upon request.
� Crack pressure: 3 psig (0.2 bar) maximum
� Maximum operating pressure: 150 psig (10 bar)
� Maximum operating temperature (based on seal materialmanufacturer’s rating):� 250°F (121°C) for Buna body seal� 350°F (176°C) for optional fluorocarbon FKM body seal.
Disk check valves must be mounted vertically.
Dimensions
A
Ordering Number 45HC 6 20
Material Grade4 = 304 SS6 = 316L SS
Item Code45HC = Kwik-Clamp45H = Acme Thread
End Connection Size50 = 1/2 in.75 = 3/4 in.10 = 1 in.15 = 1 1/2 in.20 = 2 in.25 = 2 1/2 in.30 = 3 in.40 = 4 in.
68
MISCELLANEOUS
FLOW
COMPONENTS
69
MISCELLANEOUS
FLOW
COMPONENTS
Ball Check Valves
Features
Purpose: Prevention of product backflow
� 316L SS
� Internal ball available in Buna, Nylon, EPDM, andfluorocarbon FKM. Buna is standard.
� 1 1/2 to 3 in. sizes
Ain. (mm)
1 1/2 in. 12(305)
2 in.
2 1/2 in.
3 in.
10 1/4(260)
11(279)
14(356)
Dimensions
A
EndConnection
Size
Ordering Number JC45BY 6 20
Material Grade
Item Code End Connection Size15 = 1 1/2 in.20 = 2 in.25 = 2 1/2 in.30 = 3 in.
70
MISCELLANEOUS
FLOW
COMPONENTS
Compression and Relief Valves
Features� 316L SS
� 1 to 3 in. sizes, 3/4 in. also available for clamp end.
EndConnection
SizeA
ClampA
Threaded
Dimensions, in. (mm)
3/4 in.
1 in.
1 1/2 in.
2 in.
2 1/2 in. 3 3/16(81.0)
3 in.
3 1/2(88.9)
3 3/4(95.2)
1 13/16(46.0)
2 3/8(60.3)
2 25/32(70.6)
3 1/2(88.9)
2 3/8(60.3)
2 3/4(69.8)
—
Dimensions
A
A
A
A
Ordering Number D60TMP 6 20
Material Grade
Item CodeD60TMP = Clamp end compression valveD60TM = ACME thread compression valveD60RTHMP = Clamp end relief valveD60RTH = ACME thread relief valve
End Connection Size75 = 3/4 in.10 = 1 in.15 = 1 1/2 in.20 = 2 in.25 = 2 1/2 in.30 = 3 in.
71
MISCELLANEOUS
FLOW
COMPONENTS
Sanitary Ball Valves
Features� 1/2 to 4 in. sizes
� 316 stainless steel; investment cast
� On-off (2-way) valves
� Cavity filled virgin PTFE seat
� Kwik-Clamp, butt weld, and TS series sanitary clampend connections
� True ID bore
� Blow-out proof stem
� 15 µin. (0.38 µm) Ra internal finish
� ISO 5211 and DIN 3337 mounting pads
� Locking handle
Materials of Construction
1 Body
CF8M (316 SS)/ASTM A351
Component Material / Specification
2 Flange
3 Ball
4 Seat
5 Flange seal
6 Thrust washer
7 Stem packing
8 Packing bolt
9 Stem washer
10 Stem nut
11 Stem
12 Bolt washer
13 Nut
14 Bolt
15 Handle
16 Handle sleeve
PTFE
304 SS/AISI
316 SS /ASTM A276
304 SS/AISI
301 SS/AISI
PVC
14
109
158
11
7
6
5
4
3
2
1
12
16
13
17
Pressure-Temperature Ratings1000 psig (68 bar) maximum at 72°F (22°C).
Pressure ratings will depend on temperature. Temperature islimited by materials of construction.
17 Locking latch 316 SS
Wetted components are listed in italics.
72
MISCELLANEOUS
FLOW
COMPONENTS
Ordering Information and DimensionsSelect a sanitary ball valve ordering number.
W
H
L
Dimensions are for reference only and are subject to change.➀ TS Series sanitary clamp end connections are available. Contact your local independent Swagelok sales and service representative.
Valve Sizein.
WallThickness
1/2
3/4
1
0.065
1 1/2
2
2 1/2
3
4
0.065
0.065
0.065
0.065
0.065
0.065
0.083
EndConnection➀
OrderingNumber
Tube butt weld
Kwik-Clamp
JBV650
—
—
—
—
—
—
—
—
Kwik-Clamp
Kwik-Clamp
Kwik-Clamp
Kwik-Clamp
Kwik-Clamp
Kwik-Clamp
Kwik-Clamp
Tube butt weld
Tube butt weld
Tube butt weld
Tube butt weld
Tube butt weld
Tube butt weld
Tube butt weld
JCBV650
JBV675
JCBV675
JBV610
JCBV610
JBV615
JCBV615
JBV62
JCBV62
JBV625
JCBV625
JBV630
JCBV630
JBV640
JCBV640
HWeightlb (kg)ID L W
ISO5211
0.37(9.39)
Dimensions, in. (mm)
3.50(88.9)
2.05(52.0)
0.63(16.0)
3.98(101)
2.24(56.8)
F03
1.55(0.70)
1.95(0.88)5.16
(131)
3.94(100)
0.87(22.0)
4.49(114)
2.36(59.9)
1.38(35.0)
1.87(47.4)
2.37(60.1)
2.87(72.8)
3.84(97.5)
5.51(139)
6.14(155)
7.76(197)
9.02(229)
9.49(241)
7.09(180)
3.54(88.9)
4.02(102)
5.51(139)
6.10(164)
7.36(186)
10.24(260)
11.42(290)
F04
F05
2.80(1.27)
7.00(3.17)
9.50(4.30)
19.5(8.84)
29.5(13.3)
43.0(19.5)
F10
F07
73
MISCELLANEOUS
FLOW
COMPONENTS
S.S. TUBING HANGER
3-POINT EPDM GROMMET SUPPORTJ24FCF
PVC INSERT SUPPORTJ24PVC
• Two-piece design provides maximum strength at minimum cost.
• Easily installed with standard wrenches.
• SS bolts fasten to SS lock nut with nylon insert eliminating lock washers.
• Support rods are welded to hanger at time of installation for maximum strength.
• Standard sizes: 1/2"(12.7mm) - 6"(152.4mm) tube O.D.
• For J24PVC sizes 1"(25.4mm), 3/4"(19.1mm) and 1/2"(12.7mm) the brackets do not have holes for grommets.
74
MISCELLANEOUS
FLOW
COMPONENTS
STRAINER & FILTERS(316L s/s)
Jensen's Inline Strainer is an all stainless design that is efficient, light weight, corrosionresistant, versatile, and easy to clean. It is compatible with most industry leaders. Availablein 316L S/S.
75
MISCELLANEOUS
FLOW
COMPONENTS
CONNECTIONSBEVEL SEAT CLAMP
CONNECTIONS CONNECTIONS EFFECTIVETUBE OD STRAINER LENGTH STRAINER LENGTH STRAINER AREA
in. mm PART NO. in. mm PART NO. in. mm(SQ. FT.)
111⁄2221⁄231⁄211⁄2221⁄23
25.438.150.863.588.938.150.863.576.2
S1-1S1-11⁄2S1-2S1-21⁄2S1-3S2-11⁄2S2-2S2-21⁄2S2-3
16.1316.1916.1916.3816.5035.8135.8136.0036.13
409.7411.2411.2416.1419.1909.6909.6914.4917.7
SM1-1SM1-11⁄2SM1-2SM1-21⁄2SM1-3SM2-11⁄2SM2-2SM2-21⁄2SM2-3
15.7515.7515.7515.7515.7535.3835.3835.3835.38
400.1400.1400.1400.1400.1898.7898.7898.7898.7
0.650.650.650.750.751.951.952.252.25
INLINE STRAINERS
CONNECTIONSBEVEL SEAT CLAMP
CONNECTIONS CONNECTIONS EFFECTIVETUBE OD STRAINER LENGTH STRAINER LENGTH STRAINER AREA
in. mm PART NO. in. mm PART NO. in. mm(SQ. FT.)
111⁄2221⁄2311⁄2221⁄23
25.438.150.863.576.238.150.863.576.2
F1-1F1-11⁄2F1-2F1-21⁄2F1-3F2-11⁄2F2-2F2-21⁄2F2-3
16.1316.1916.1916.3816.5035.8135.8136.0036.13
409.7411.2411.2416.1419.1909.6909.6914.4917.7
FM1-1FM1-11⁄2FM1-2FM1-21⁄2FM1-3FM2-11⁄2FM2-2FM2-21⁄2FM2-3
15.7515.7515.7515.7515.7535.3835.3835.3835.38
400.1400.1400.1400.1400.1898.7898.7898.7898.7
0.650.650.650.750.751.951.952.252.25
INLINE FILTERS
MEDIA MICRON DESCRIPTIONTYPE RATING30B30C30D30E30G30N
50030076540
420250
COTTON FLANNELCOTTON CHEESE CLOTHWOVEN NYLON OR POLYESTERNON-WOVEN RAYONWOVEN NYLON OR RAYON, 40 MESHSMOOTH WEAVE DACRON
FILTER MEDIA SCHEDULE
PART USE INSIDE OF . . .
HOLES PER % OFNUMBER SQUARE INCH OPEN AREA
S1CORES1WCORES2CORES2WCORES1CORE18S1WCORE18S2CORE18S2WCORE18
5858585840404040
9999
40404040
1", 1.5" & 2" SHORT UNITS2.5" & 3" SHORT UNITS1", 1.5" & 2" LONG UNITS2.5" & 3" LONG UNITS1", 1.5" & 2" SHORT UNITS2.5" & 3" SHORT UNITS1", 1.5" & 2" LONG UNITS2.5" & 3" LONG UNITS
REPLACEMENT PERFORATED BACK-UP TUBES
76
MISCELLANEOUS
FLOW
COMPONENTS
SIGHTGLASS ASSEMBLY
Model JCD 54304 s/s or 316L s/s
Jensen's Sightglass Assembly, along with Jensen's Kwik-Clampconnections, allow fast takedown for cleaning. It can be easily installed innew or existing clamp lines because it has the same center to face dimen-sions as our standard tee or cross. Pyrex glass is utilized to provide extrastrength. (Buna N Gasket.)
77
MISCELLANEOUS
FLOW
COMPONENTS
JensenSIGHTGLASS ASSEMBLY
S
S
H
JJ
W
MODEL JCD54Sight Glass Assembly Dimensions
SIZE H W J S
in. mm in. mm in. mm in. mm in. mm
11⁄2221⁄234
38.150.863.576.2
101.6
51⁄27771⁄29
139.7177.8177.8190.5228.6
45⁄851⁄861⁄261⁄875⁄8
117.5130.2165.1155.6193.7
13⁄815⁄825⁄16
21⁄827⁄8
34.941.358.754.073.0
23⁄431⁄231⁄233⁄441⁄2
69.988.988.995.3
114.3
Some benefits of our Sightglass are:1) Fast Inspection2) Fast and Easy to Clean3) Compatible with most Clamp Connections.4) Available in 304 or 316L s/s
78
MISCELLANEOUS
FLOW
COMPONENTS
JensenSIGHTGLASS
JENSAFE SIGHT GLASS#162S
INLINE SIGHT GLASS#162
A
ACRYLIC SHIELD
PYREX GLASS
C
PYREX GLASS
B
D
162S JENSAFE SIGHTGLASS‘A’ OVERALL LENGTH DIMENSIONSSIZE
BUTT WELD ACME THREAD KWIK CLAMP C
in. mm in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
31⁄231⁄231⁄2555
88.988.988.9
127.0127.0127.0
61⁄461⁄261⁄281⁄281⁄281⁄2
158.8165.1165.1215.9215.9215.9
53⁄453⁄453⁄471⁄471⁄471⁄4
146.1146.1146.1184.2184.2184.2
5551⁄261⁄261⁄28
127.0127.0139.7165.1165.1203.2
162 JENSAFE SIGHTGLASS‘A’ OVERALL LENGTH DIMENSIONSSIZE
BUTT WELD ACME THREAD KWIK CLAMP D
in. mm in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
33⁄833⁄833⁄837⁄8551⁄8
85.785.785.798.4
127.0130.2
61⁄863⁄863⁄873⁄881⁄285⁄8
155.6161.9161.9187.3215.9219.1
55⁄855⁄855⁄861⁄871⁄473⁄8
142.9142.9142.9155.6184.2187.3
31⁄4441⁄443⁄451⁄261⁄2
82.6101.6108.0120.7139.7165.1
(Note: Pyrex Glass utilized with WhiteBuna Gasket & any type of endconnection you desire is available)
79
MISCELLANEOUS
FLOW
COMPONENTS
JensenSIGHTGLASS
162 162S
(Note: Pyrex Glass utilized with White BunaGasket & any type of end connection you desire is available)
Jensen Offers A Special Safety SightglassJENSAFE
(162 S)
The Jensafe features a heavy duty, clearacrylic protective shell surrounding thePyrex glass. The purpose of this protec-tive shell is to protect the glass fromfalling objects, which may cause break-age. Jensafe also offers much higherPSI and temperature ratings than mostsightglasses available. This sightglasscan be provided with thread, flange,clamp or weld ends. Special ends canalso be manufactured to customer draw-ings or specifications.
80
MISCELLANEOUS
FLOW
COMPONENTS
WELD IN SIGHTGLASS(JC54W)
This sightglass connects to the standard clamp fittings and allows for quick disassembly.This unit is available in 304 or 316L, sizes 11⁄2"(38.1mm), 2"(50.8mm), 3"(76.2mm), or 4"(101.6mm).
LATERAL & TRUE YKwik Clamp/Butt Weld/Acme Threaded
(304 s/s or 316L s/s)
Jensen offers an excellentquality Lateral Y, ReducingLateral Y or True Y, in any type end configuration you require.
81
MISCELLANEOUS
FLOW
COMPONENTS
ADAPTER SIZE R B
in. mm in. mm in. mm
FLOW PLATE
11⁄2221⁄23
38.150.863.576.2
41⁄4671⁄29
108.0152.4190.5228.6
15202426
381.0508.0609.6660.4
Seven Kwik Clamp Ferrules
ADAPTER SIZE A B
in. mm in. mm in. mm
FLOW PLATE
11⁄2221⁄23
38.150.863.576.2
41⁄4671⁄29
108.0152.4190.5228.6
10151515
254.0381.0381.0381.0
Four Kwik Clamp Ferrules
TTube OD, in.
FlangeSize, in.
OrderingNumber A B D
EMinimumOpening F
GHex Flat I
1/4 1/2 SS-400-SC-8 1.57 0.37 0.60 0.19 1 9/16 0.98
1/4 3/4 SS-400-SC-12 1.57 0.62 0.60 0.19 1 9/16 0.98
1/4 1 SS-400-SC-16 1.57 0.87 0.60 0.19 1 3/8 9/16 1.98
1/4 1 1/2 SS-400-SC-24 1.57 1.37 0.60 0.19 1 3/8 9/16 1.98
3/8 1/2 SS-600-SC-8 1.63 0.37 0.66 0.28 1 11/16 0.98
3/8 3/4 SS-600-SC-12 1.63 0.62 0.66 0.28 1 11/16 0.98
3/8 1 SS-600-SC-16 1.63 0.87 0.66 0.28 1 3/8 11/16 1.98
3/8 1 1/2 SS-600-SC-24 1.63 1.37 0.66 0.28 1 3/8 11/16 1.98
1/2 1/2 SS-810-SC-8 1.74 0.37 0.86 0.37 1 7/8 0.98
1/2 3/4 SS-810-SC-12 1.74 0.62 0.86 0.41 1 7/8 0.98
1/2 1 SS-810-SC-16 1.74 0.87 0.86 0.41 1 3/8 7/8 1.98
1/2 1 1/2 SS-810-SC-24 1.74 1.37 0.86 0.41 1 3/8 7/8 1.98
1 1 SS-1610-SC-16 1.91 0.87 1.04 0.87 1 3/8 1 1/2 1.98
1 2 SS-1610-SC-32 2.49 1.87 1.04 0.88 2 3/4 1 1/2 2.52
Sanitary Flange To Swagelok Tube Fitting
IB
F
E
G
T
D
A
Dimensions are for reference only and are subject to change.
82
MISCELLANEOUS
FLOW
COMPONENTS
INTERLOCK FITTINGS
Jensen's Interlock 304 and 316L Fittings.
These are available in 1"(25.4mm) through 4"(101.6mm) and are compatible with the othermanufacturers of these types of fittings.
83
MISCELLANEOUS
FLOW
COMPONENTS
INTERLOCK FITTINGS
SIZE A
in. mm in. mm
14WI
111⁄2221⁄234
25.438.150.863.576.2
101.6
19⁄323⁄425⁄3227⁄3229⁄32
11⁄32
15.119.119.821.423.026.2
A
SIZE A
in. mm in. mm
15WI
111⁄2221⁄234
25.438.150.863.576.2
101.6
25⁄3215⁄16
11⁄32
15⁄32
17⁄32
111⁄32
19.823.826.229.430.934.1
A
SIZE
in. mm
13IS
111⁄2221⁄234
25.438.150.863.576.2
101.6
SIZE
in. mm
16AI-14I
111⁄2221⁄234
25.438.150.863.576.2
101.6
SIZE
in. mm
16AI-15I
111⁄2221⁄234
25.438.150.863.576.2
101.6
84
MISCELLANEOUS
FLOW
COMPONENTS
JOHN PERRY FITTINGS14WJP
SIZE A B(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
11⁄1623⁄3213⁄1627⁄3227⁄32
17⁄32
17.418.220.621.421.430.9
111⁄2221⁄234
25.438.150.863.576.2
101.6
15WFF
SIZE A B(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
5⁄85⁄83⁄427⁄327⁄811⁄16
15.915.919.121.422.227.0
111⁄2221⁄234
25.438.150.863.576.2
101.6
14AJP
SIZE A B(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
13⁄811⁄211⁄213⁄413⁄413⁄4
34.938.138.144.544.544.5
111⁄2221⁄234
25.438.150.863.576.2
101.6
15AFF
SIZE A B(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
13⁄811⁄211⁄213⁄413⁄413⁄4
34.938.138.144.544.544.5
111⁄2221⁄234
25.438.150.863.576.2
101.6
16AJP
SIZE A B(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
11⁄8121⁄32
23⁄16
221⁄32
33⁄16
43⁄16
28.642.155.567.580.9
106.3
15⁄321⁄217⁄325⁄85⁄85⁄8
11.912.713.515.915.915.9
13H
SIZE A B(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
113⁄16
213⁄32
3319⁄32
43⁄16
57⁄16
46.061.176.291.3
106.3138.1
29⁄3231⁄32
11⁄16
13⁄16
11⁄411⁄2
23.024.627.030.131.838.1
85
MISCELLANEOUS
FLOW
COMPONENTS
APV FITTINGSK-CLAMP
SIZE A
in. mm in. mm
JA2
111⁄2221⁄234
25.438.150.863.576.2
101.6
23⁄16
215⁄16
33⁄4419⁄32
513⁄32
7
55.574.695.3
116.7137.3177.8
SIZE MG
in. mm in. mm
JA2K
111⁄2221⁄234
25.438.150.863.576.2
101.6
15⁄16
113⁄32
2213⁄32
225⁄32
31⁄2
33.335.750.861.170.688.9
JA7
SIZE C E(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
35⁄843⁄459⁄16
63⁄8795⁄16
92.1120.7141.3161.9177.8236.5
113⁄16
23⁄8225⁄32
33⁄16
31⁄2421⁄32
46.060.370.680.988.9
118.3
JA9
SIZE C E(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
35⁄843⁄459⁄16
63⁄8795⁄16
92.1120.7141.3161.9177.8236.5
113⁄16
23⁄8225⁄32
33⁄16
31⁄2421⁄32
46.060.370.680.988.9
118.3
86
MISCELLANEOUS
FLOW
COMPONENTS
K-CLAMP
JA14X
SIZE A B C(TUBE O.D.)in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
11⁄1611⁄163⁄427⁄3229⁄32
1
17.417.419.121.423.025.4
0.871.371.872.372.873.83
22.134.847.560.272.997.3
111⁄2221⁄234
25.438.150.863.576.2
101.6
JA14A
SIZE A B C(TUBE O.D.)in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
13⁄817⁄825⁄16
21⁄2211⁄16
23⁄4
34.947.658.763.568.269.9
0.871.371.872.372.873.83
22.134.847.560.272.997.3
111⁄2221⁄234
25.438.150.863.576.2
101.6
JA14
SIZE A B C(TUBE O.D.)in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
221⁄421⁄223⁄434
50.857.263.569.976.2
101.6
0.871.371.872.372.873.83
22.134.847.560.272.997.3
111⁄2221⁄234
25.438.150.863.576.2
101.6
SIZE A
in. mm in. mm
JA16
111⁄2221⁄234
25.438.150.863.576.2
101.6
1⁄41⁄41⁄41⁄41⁄41⁄4
6.46.46.46.46.46.4
A
87
MISCELLANEOUS
FLOW
COMPONENTS
SIZE A
in. mm in. mm
2CPV
111⁄2221⁄234
25.438.150.863.576.2
101.6
23⁄16
215⁄16
33⁄4419⁄32
513⁄32
7
55.574.695.3
116.7137.3177.8
SIZE A
in. mm in. mm
2EPV
111⁄2221⁄234
25.438.150.863.576.2
101.6
23⁄32
227⁄32
321⁄32
415⁄32
59⁄32
613⁄16
53.272.292.9
113.5134.1173.0
2FPV
SIZE AG Y(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
227⁄8323⁄32
427⁄32
529⁄32
81⁄16
50.873.094.4
123.0150.0204.8
23⁄16
215⁄16
33⁄4419⁄32
513⁄32
7
55.574.695.3
116.7137.3177.8
2PPV
SIZE MG NG(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
15⁄16
123⁄32
21⁄825⁄831⁄841⁄4
33.343.654.066.779.4
108.0
23⁄16
215⁄16
33⁄4213⁄32
225⁄32
31⁄2
55.574.695.361.170.688.9
A
A
A
A
Y
AG
NG
45˚
MG
PV THREADED
88
MISCELLANEOUS
FLOW
COMPONENTS
7PV
SIZE C E(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
35⁄843⁄459⁄16
63⁄8795⁄16
92.1120.7141.3161.9177.8236.5
113⁄16
23⁄8225⁄32
33⁄16
31⁄2421⁄32
46.060.370.680.988.9
118.3
7APV
SIZE C E E1(TUBE O.D.)in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
35⁄843⁄459⁄16
63⁄8795⁄16
92.1120.7141.3161.9177.8236.5
113⁄16
23⁄8225⁄32
33⁄16
31⁄2421⁄32
46.060.370.680.988.9
118.3
239⁄64
319⁄64
323⁄32
41⁄841⁄2561⁄64
66.383.794.4
104.8114.3151.2
9PV
SIZE C E(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
35⁄843⁄459⁄16
63⁄8795⁄16
92.1120.7141.3161.9177.8236.5
113⁄16
23⁄8225⁄32
33⁄16
31⁄2421⁄32
46.060.370.680.988.9
118.3
14APV
SIZE OL N T(TUBE O.D.)in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
119⁄64
149⁄64
27⁄32
23⁄829⁄16
237⁄64
32.944.856.360.365.165.5
0.871.371.872.372.873.83
22.134.847.560.272.997.3
111⁄2221⁄234
25.438.150.863.576.2
101.6
E EC
E
E E
C
E1
E E
C
E
E
OL
TN
PV THREADED
89
MISCELLANEOUS
FLOW
COMPONENTS
14WLPV
SIZE A N T(TUBE O.D.)in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
159⁄64
29⁄64
213⁄32
25⁄827⁄8353⁄64
48.854.461.166.773.097.2
0.871.371.872.372.873.83
22.134.847.560.272.997.3
111⁄2221⁄234
25.438.150.863.576.2
101.6
14WXPV
SIZE A B C(TUBE O.D.)in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
39⁄6437⁄6421⁄3223⁄3225⁄3253⁄64
15.514.716.718.219.821.0
0.871.371.872.372.873.83
22.134.847.560.272.997.3
111⁄2221⁄234
25.438.150.863.576.2
101.6
15APV
SIZE A N T(TUBE O.D.)in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
15⁄817⁄823⁄825⁄827⁄827⁄8
41.347.660.366.773.073.0
0.871.371.872.372.873.83
22.134.847.560.272.997.3
111⁄2221⁄234
25.438.150.863.576.2
101.6
15WLPV
SIZE A N T(TUBE O.D.)in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
221⁄421⁄223⁄434
50.857.263.569.976.2
101.6
0.871.371.872.372.873.83
22.134.847.560.272.997.3
111⁄2221⁄234
25.438.150.863.576.2
101.6
PV THREADED
A
T
N
A
B C
A
T
N
A
TN
90
MISCELLANEOUS
FLOW
COMPONENTS
15WXPV
SIZE A B C(TUBE O.D.)in. mm in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
11⁄1611⁄163⁄427⁄3229⁄32
1
17.417.419.121.423.025.4
0.871.371.872.372.873.83
22.134.847.560.272.997.3
111⁄2221⁄234
25.438.150.863.576.2
101.6
PV THREADED
SIZE OL
in. mm in. mm
16APV
111⁄2221⁄234
25.438.150.863.576.2
101.6
19⁄6427⁄6415⁄3215⁄321⁄217⁄32
7.510.711.911.912.713.5
13H
SIZE A B(TUBE O.D.)in. mm in. mm in. mm111⁄2221⁄234
25.438.150.863.576.2
101.6
113⁄16
213⁄32
3319⁄32
43⁄16
57⁄16
46.061.176.291.3
106.3138.1
29⁄3231⁄32
11⁄16
13⁄16
11⁄411⁄2
23.024.627.030.131.838.1
B C
A
91
MISCELLANEOUS
FLOW
COMPONENTS
We Specialize In “Specials”Jensen offers a wide range of “special” products to fit your “special” needs.The following are a few examples of what we can do for you. We will provide CADdrawings within hours and finished product within days.
2" KC MANIFOLD
92
MISCELLANEOUS
FLOW
COMPONENTS
2" x 4" x 3/4" KC ASSEMBLY
1/2" KC x KC 45 ̊RETURN ASSEMBLY
93
MISCELLANEOUS
FLOW
COMPONENTS
8" BODY MANIFOLD
SIDE INLET DUAL STRAINER
94
MISCELLANEOUS
FLOW
COMPONENTS
4" KC CAPPED ADAPTER
APV REDUCING 180 RETURN BEND
95
MISCELLANEOUS
FLOW
COMPONENTS
What is the symbol?
It is the symbol which manufacturers of dairy equipment may affix to their product when itconforms to 3-A Sanitary Standards.
The sanitary standards themselves are collaboratively formulated by groups representingprocessors, suppliers and regulatory officials, with the advice of sanitation specialists from thefederal government. The standards are voluntarily met by fabricators and manufacturers.Generally, equipment which conforms to a 3-A Sanitary Standards is accepted by federal, state,and local regulatory authorities.
Who may use the symbol?
Only those manufacturers whose equipment conforms to existing 3-A Sanitary Standards, andwho are authorized to do so by the 3-A Sanitary Standards Symbol Administrative Council.Because the standards themselves may be amended, manufacturers must apply annually forthe privilege of using the 3-A Symbol, and must indicate annually that in all respects theirproducts conform to published 3-A Sanitary Standards.
Jensen Fittings Corporation is proud to be anactive participant in the program.
ISO 9001, Quality systems - Model for qualityassurance in design/development, production,installation and servicing.
For use when conformance to specifiedrequirements is to be assured by the supplier during several stages which may includedesign/development, production, installation and servicing.
ISO 9002, Quality systems - Model for qualityassurance in production and installation.
For use when conformance to specifiedrequirements is to be assured by the supplier during production and installation.
ISO 9003, Quality systems - Model for qualityassurance in final inspection and test.
For use when conformance to specifiedrequirements is to be assured by the supplier solely at final inspection and test.
It is emphasized that the quality systemrequirements specified in this International Standard,ISO 9001 and ISO 9003 are complimentary (notalternative) to the technical (product/service)specified requirements.
It is intended that these International Standards will normally be adopted in their present form, but onoccasions they may need to be tailored for specificcontractual situations. ISO 9000 provided guidanceon such tailoring as well as selection of theappropriate quality assurance model, for example,ISO 9001, ISO 9002 or ISO 9003.
Jensen ALSO PROVIDES...• Tubing, 304 or 316L S/S• Customer Engineering & Manufacturing
Contact us with any of your engineeringneeds.
Since 1959 we have provided competitiveprices, with excellent quality & service.
ISO
REG
ISTERED • QUALITY
•S
YS
TE
M
ISOREGISTERED
is an ISO Registered
Company.
International
Standard for Total
Quality Systems.
Safe Product SelectionWhen selecting a product, the total system designmust be considered to ensure safe, trouble-freeperformance. Function, material compatibility,adequate ratings, proper installation, operation, andmaintenance are the responsibilities of the systemdesigner and user.
Swagelok—TM Swagelok Company© 2001, 2002 Swagelok CompanyPrinted in U.S.A., GLLOctober 2002, R3MS-02-150