Post on 24-Mar-2021
transcript
I ntegr i t y. Par tnership. Qual i t y.
DBCI’s Commercial Steel Curtain Roll-Up Door Solutions Include:
1900 Series (1950 Insulated)• 26-gauge Grade E galvanized
2000 Series (2250 Insulated) • 16-gauge galvanized steel drums with steel ball bearings• 26-gauge Grade E steel curtain
2500 Series (2750 Insulated)• Heavy duty• 10-gauge steel slide bolt lock• Width up to 18 feet
5000 Series (5250 Insulated)• Aluminum bottom bar with steel angle reinforcement• Wind certified up to 20’ wide
SE
RIE
S
DBCI’s 1900 Series is suitable for a number of light-
duty commercial uses. These doors are easy to
install and require low maintenance. You will enjoy
steady, quiet operation. The 1900 Series utilizes
9 ½” drums instead of the standard 12” drum.
This allows for less headroom when installing the
doors. DBCI’s commercial-grade steel curtain
roll-up doors are designed to meet and/or exceed
operational requirements for commercial doors
with little or no maintenance.
COMMERCIAL DOOR 1900 LIGHT-DUTY COMMERCIAL GRADE DOOR
DBCI | Toll Free: 800.542.0501 | E-mail: commercial@dbci.com | * For more detailed information and drawings: www.dbci.com
Cur tain
• 26-gauge galvanized, Grade E hard steel• Deep-ribbed corrugation• Maximum opening size of 12’ x 14’• Siliconized polyester WeatherX paint
over prime coat• 20 standard colors, special colors
available upon request• Wash coat over primer interior side• 30-year film integrity warranty, up to
25-year chalk and fade warranty• Flexible wear strips• NOTE: The 1900 is not rated for wind
loads. Please see the 2500 or 5000.
Bottom Bar
• 6063 – T6 aluminum extrusion• 2” x 1 ½” galvanized angles• Bulb astragal (Durometer 75)• Stainless steel nuts and bolts
Axle -Drum Assembly
• 1 5/16” O.D. steel axle, 14-gauge• 11-gauge on doors over 10’• Oil-tempered torsion springs• Utilizes 9 ½”, 18-gauge drums• Shielded steel ball bearings in drums• 26-gauge full top sheet
A .C .E . Guide System
• Advanced Curtain Engagement guide system
• Galvanized steel• Adjustable bolt on head stop• Polyethylene wear strip• Pre-punched for lock and attachment
fasteners
Hardware
• 13-gauge saddle clamps• 10-gauge slide locks; two per door• 16-gauge step plate; two per door• ¼” steel angle T-bracket
Opt ions
• Insulation 1950 Series• Chain hoist 4:1 reduction• Vision panels (17” x 5”)• Top draft stop• Hood• Steel mounting plates
Opening Height Headroom
• Up to 10’ is 17” of headroom• 10’ to 14’ is 19” of headroom
GUIDEDETAIL
DOORENGAGEMENT
INSULATEDDOOR DETAIL
GUIDEMOUNTING
INTERIORELEVATION
DOOR OPENING
OPENING WIDTH + 18"
HEADROOM
16 GA.
1.74
0.56
1.30
1.91
1.91
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
SELF DRILLINGSCREW
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
FOIL BACKED AIR-BUBBLE INSULATIONVINYL SIDE DRAFT STOP
SELF DRILLINGSCREW
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
SELF DRILLINGSCREWTAPCON XL
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
WOOD SCREW
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
STEEL MOUNTMASONRY MOUNT WOOD MOUNT
SERIES 1900
SERIES 1950
I ntegr i t y. Par tnership. Qual i t y.
DBCI’s Commercial Steel Curtain Roll-Up Door Solutions Include:
1900 Series (1950 Insulated)• 26-gauge Grade E galvanized
2000 Series (2250 Insulated) • 16-gauge galvanized steel drums with steel ball bearings• 26-gauge Grade E steel curtain
2500 Series (2750 Insulated)• Heavy duty• 10-gauge steel slide bolt lock• Width up to 18 feet
5000 Series (5250 Insulated)• Aluminum bottom bar with steel angle reinforcement• Wind certified up to 20’ wide
SE
RIE
S
COMMERCIAL DOOR 2000 LIGHT DUTY COMMERCIAL GRADE DOOR
The 2000 Series is the right choice for light-duty
applications requiring frequent usage such as
warehouses, freight terminals, car washes, machine
shops, auto body shops and much more. The
16-gauge, 12” drums allow for easy retraction. These
doors are low-maintenance, which is what every
owner wants in a quality door. DBCI’s commercial-
grade steel curtain roll-up doors are designed to
meet and/or exceed operational requirements for
commercial doors with little or no maintenance.
DBCI | Toll Free: 800.542.0501 | E-mail: commercial@dbci.com | * For more detailed information and drawings: www.dbci.com
GUIDEDETAIL
DOORENGAGEMENT
INSULATEDDOOR DETAIL
GUIDEMOUNTING
INTERIORELEVATION
Cur tain
• 26-gauge galvanized, Grade E hard steel• Deep-ribbed corrugation• Maximum opening size of 12’ x 18’• Flexible wear strips• NOTE: The 2000 is not rated for wind
loads. Please see the 2500 or 5000.
Bottom Bar
• 6063 – T6 aluminum extrusion• 2” x 1 ½” galvanized angles• Bulb astragal• Stainless steel nuts and bolts
Axle -Drum Assembly
• 1 5⁄16” O.D. steel axle, 14-gauge• 11-gauge axle on doors over 10’ wide• Utilizes 12”, 16-gauge drums• Shielded steel ball bearings in drums• Full top sheet
A.C .E . Guide System
• 16-gauge galvanized steel• Adjustable bolt on head stop• Polyethylene wear strip• Pre-punched for lock and attachment
fasteners
Hardware
• Saddle clamps with set fasteners• 10-gauge slide locks; 2 per door• 16-gauge step plate; 2 per door• ¼” steel angle T-bracket
Opening Height Headroom
• Doors up to 10’ have 20” of headroom• Doors 10’ to 14’ have 22” of headroom• Doors over 14’ have 24” of headroom
Options
• Insulated 2250 Series• 1900 Series – low overhead option• Chain hoist 4:1 reduction• Vision panels (17” x 5”)• Top draft stop• Hood• Steel mounting plates• Electric operator
SERIES 2000
SERIES 2250
DOOR OPENING
OPENING WIDTH + 18"
HEADROOM
16 GA.
1.74
0.56
1.30
1.91
1.91
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
SELF DRILLINGSCREW
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
FOIL BACKED AIR-BUBBLE INSULATIONVINYL SIDE DRAFT STOP
SELF DRILLINGSCREW
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
SELF DRILLINGSCREWTAPCON XL
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
WOOD SCREW
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
STEEL MOUNTMASONRY MOUNT WOOD MOUNT
I ntegr i t y. Par tnership. Qual i t y.
DBCI’s Commercial Steel Curtain Roll-Up Door Solutions Include:
1900 Series (1950 Insulated)• 26-gauge Grade E galvanized
2000 Series (2250 Insulated) • 16-gauge galvanized steel drums with steel ball bearings• 26-gauge Grade E steel curtain
2500 Series (2750 Insulated)• Heavy duty• 10-gauge steel slide bolt lock• Width up to 18 feet
5000 Series (5250 Insulated)• Aluminum bottom bar with steel angle reinforcement• Wind certified up to 20’ wide
SE
RIE
S
I ntegr i t y. Par tnership. Qual i t y.
COMMERCIAL DOOR 2500 HEAVY DUTY COMMERCIAL GRADE DOOR
The 2500 Series is DBCI’s heavy duty steel curtain
roll-up door with tremendous versatility and
unmatched quality. The 2500 Series has deep
engagement guides creating greater durability
and stronger, longer lasting performance. DBCI’s
commercial-grade steel curtain roll-up doors are
designed to meet and/or exceed operational
requirements for commercial doors with little or
no maintenance.
INTERIORELEVATION
GUIDEMOUNTING
GUIDEDETAIL
DOORENGAGEMENT
INSULATEDDOOR DETAIL
DBCI | Toll Free: 800.542.0501 | E-mail: commercial@dbci.com | Website: www.dbci.com
Cur ta in
• 26-gauge galvanized, Grade E hard steel• Deep-ribbed corrugation• Maximum opening size of 18’ x 18’• Flexible wear strips• NOTE: The 2500 Series are wind rated up
to 12’0” wide and approximately 90 MPH. The MPH rating increases as the door width decreases. For test results on doors up to 12’0” wide, please contact DBCI Sales at 800.542.0501.
Bottom Bar
• 6063 – T6 aluminum extrusion• 2” x 1 ½” galvanized angles• Bulb astragal• Stainless steel nuts and bolts
Axle -Drum Assembly
• 1 5⁄16” O.D. steel axle, 14-gauge• 11-gauge axle on doors over 10’ wide• Utilizes 12”, 16-gauge drums• Shielded steel ball bearings in drums• Full top sheet• Oil tempered torsion springs
A.C.E . Guide System • 14-gauge galvanized steel• Adjustable bolt on head stop• Polyethylene wear strip• Pre-punched for lock and attachment
fasteners
Hardware
• Saddle clamps with set fasteners• 10-gauge slide locks; 2 per door• 16-gauge step plate; 2 per door• ¼” steel welded angle T-bracket
Opening Height Headroom
• Doors up to 10’ have 20” of headroom• Doors 10’ to 14’ have 22” of headroom• Doors over 14’ have 24” of headroom
Options
• Insulated 2750 Series• Chain hoist 4:1 reduction• Vision panels (17” x 5”)• Top draft stop• Hood• Steel mounting plates• Electric operator• Low headroom 2400 Series
DOOR OPENING
OPENING WIDTH + 18"
HEADROOM
14 GA.
2.97
3.16
1.94
0.57
1.30
SERIES 2500
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
SELF DRILLINGSCREW
SERIES 2750
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
FOIL BACKED AIR-BUBBLE INSULATIONVINYL SIDE DRAFT STOP
SELF DRILLINGSCREW
MASONRY MOUNT
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
TAPCON XL
STEEL MOUNT
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
SELF DRILLINGSCREW
WOOD MOUNT
DOOR SHEETCURTIANWEAR STRIP
GUIDE STRIP
WOOD SCREW
DBCI’s Commercial Steel Curtain Roll-Up Door Solutions Include:
SE
RIE
S
1900 Series (1950 Insulated)• 26-gauge Grade E galvanized
2000 Series (2250 Insulated) • 16-gauge galvanized steel drums with steel ball bearings• 26-gauge Grade E steel curtain
2500 Series (2750 Insulated)• Heavy duty• 10-gauge steel slide bolt lock• Width up to 18 feet
5000 Series (5250 Insulated)• Aluminum bottom bar with steel angle reinforcement• Wind certified up to 20’ wide
COMMERCIAL DOOR 5000 WIND CERTIFIED DOOR
When it comes to withstanding Mother Nature’s
wrath, DBCI has the doors you need. Our 5000
Series utilizes deep engagement guides and side
curtain windlocks that are designed to maintain
the operation integrity of the door and meet
most state and local building codes, especially
in coastal regions and Florida. The 5000 Series is
made of 26-gauge, Grade E hard steel to ensure
quality and dependability. DBCI’s commercial-
grade steel curtain roll-up doors are designed to
meet and/or exceed operational requirements for
commercial doors with little or no maintenance.
I ntegr i t y. Par tnership. Qual i t y.
Cur tain
• 26-gauge galvanized, Grade E hard steel• Deep-ribbed corrugation with three-rivet
windlock attachment• Maximum opening size of 20’ x 16’• Flexible wear strips• NOTE: The 5000 Series are wind rated up
to 20’0” wide and approximately 120 MPH. The MPH rating increases as the door width decreases. For test results on doors up to 20’0” wide, please contact DBCI Sales at 800.542.0501.
Approximate* MPH Cer t i f icat ion
• 10’ wide = 150 mph• 12’ wide = 150 mph• 14’ wide = 146 mph• 16’ wide = 140 mph
*For test results on doors up to 20’ wide, please contact DBCI Commercial Sales at 800.542.0501.
Bottom Bar
• 6063 – T6 aluminum extrusion• 2” x 1 ½” galvanized angles• Bulb astragal• Stainless steel nuts and bolts
Axle -Drum Assembly
• 1 5⁄16” O.D. steel axle, 14-gauge• 11-gauge axle on doors over 10’ wide• Utilizes 12”, 16-gauge drums• Shielded steel ball bearings in drums• Full top sheet• Oil tempered torsion springs
A.C.E . Guide System
• 12-gauge galvanized steel• 12-gauge wind lock bar• Adjustable bolt on head stop• Polyethylene wear strip• Pre-punched for lock and attachment fasteners
Hardware
• Saddle clamps with set fasteners• 10-gauge slide locks; 2 per door• 16-gauge step plate; 2 per door• ¼” steel angle T-bracket
Opening Height Headroom
• Doors up to 10’ require 20” of headroom• Doors 10’ to 14’ require 22” of headroom• Doors over 14’ require 24” of headroom
Options
• Chain hoist 8:1 reduction• Header seal• Hood• Steel mounting plates• Electric operator
GUIDEDETAIL
GUIDEMOUNTING
DOORENGAGEMENT
INTERIORELEVATION
MASONRY MOUNT STEEL MOUNT
DBCI | Toll Free: 800.542.0501 | E-mail: commercial@dbci.com | Website: www.dbci.com
CURTAIN
HEAD STOP(REMOVABLE)SYMMETRICAL
BOTTOM BARASSEMBLY
END
OF
AX
LE
END
OF
AX
LE
WALL OPENING WIDTH
6-1/2"
10-1/2"10 1/2"
TOP BARREL ASSEMBLY
GUIDE WOOD/STEEL JAMBS
UNIVERSAL GUIDE
CONCRETE/MASONRY JAMBS
4"GRADE
BRACKET ATTACHMENT:CONCRETE/MASONRY: SLEEVE ANCHOR, 3/8" X 1-7/8" LG.WOOD: LAG SCREW, 3/8-7 X 3" LG.STEEL: HEX BOLT, GR.5, 3/8-24 X 1-1/4" LG.
(*) FOR PUSH-UP OPERATION 6-1/2" FOR HAND CHAIN OR ELECTRIC OPERATION 10"NOTE: LEFT SIDE DRIVE SHOWN
TYPICAL PANEL
1/2"
1"MIN.
WIND LOCK AT EVERYOTHER CORRUGATION
GUIDE
3/8" SLIP FOR DOOR WIDTHLESS THAN OR EQUAL TO12'-10"; 1/2" SLIP FOR DOORWITH GREATER THAN 12'-10"AND LESS THAN 16'-10"
TYPICAL PANEL
WIND LOCK AT EVERYOTHER CORRUGATION
GUIDE
EXISTINGSTEEL JAMB
TYPICAL PANEL
WIND LOCK AT EVERYOTHER CORRUGATION
GUIDE
EXISTING STEEL JAMB1/4" MIN. THICKNESS
Fueled by constant changes in local and national building codes, as well as increasing insurance costs, doors with validated wind certification can dramatically reduce maintenance and replacement costs and minimize downtime. DBCI’s wind-certified doors are designed to meet stringent building codes in coastal regions and Florida.
*Also avai lable with insulat ion (5250 Ser ies)