Post on 10-Dec-2015
description
transcript
THESIS
VALUABLE UTILIZATION OF SPRAY DRYER ASH AND ITS PERFORMANCE
IN STRUCTURAL CONCRETE
Submitted by
Carolyne Alex Namagga
Department of Civil and Environmental Engineering
In partial fulfillment of the requirements
For the Degree of Master of Science
Colorado State University
Fort Collins, Colorado
Spring 2010
ii
COLORADO STATE UNIVERSITY
March 29, 2010
WE HEREBY RECOMMEND THAT THE THESIS PREPARED UNDER OUR
SUPERVISION BY CAROLYNE NAMAGGA ENTITLED VALUABLE
UTILIZATION OF SPRAY DRYER ASH AND ITS PERFORMANCE IN
STRUCTURAL CONCRETE BE ACCEPTED AS FULFILLING IN PART
REQUIREMENTS FOR THE DEGREE OF MASTER OF SCIENCE.
Committee on Graduate Work
_________________________________________
Mehmet E. Ozbek
_________________________________________ John W. van de Lindt
_________________________________________ Advisor: Rebecca A. Atadero
_________________________________________ Department Head: Luis Garcia
iii
ABSTRACT OF THESIS
VALUABLE UTILIZATION OF SPRAY DRYER ASH AND ITS PERFORMANCE
IN STRUCTURAL CONCRETE
This research focuses on the valuable utilization of Spray Dryer Ash (SDA) and
investigates its performance in concrete for structural and transportation applications.
Based on the challenges associated with coal ash (including SDA) and the economic
costs linked to cement production, this research seeks to provide an environmentally
friendly and more cost effective concrete product by utilizing SDA in partial replacement
of cement in concrete. Cement production is a rather expensive venture and yet there is
an abundance of coal ash that is disposed of in landfills that could be utilized positively.
The fineness and low carbon content properties of SDA/ Class C fly ash provide potential
benefits of increased strength (compressive and bond) and durability (freeze-thaw and
corrosion) when used in concrete. With the exception of high sulfur content, SDA
exhibits very excellent properties that are closely related to Class C fly ash and Portland
cement.
The addition of Spray Dryer Ash in non-air entrained concrete provided a general
increase in its strength. The compressive strength test results indicate that replacing
proportions of cement with SDA would provide improved strength and a most cost
effective solution. When utilized within optimal limits of 25-35% replacement, SDA
iv
presents reasonable benefits to compressive and bond strength. The utilization of SDA
provided modest benefits when used in certain proportions and at the very least it did not
seem to degrade the properties much. It produced a negligible effect on the freeze-thaw
durability of the concrete while an increase in the SDA provided an increased corrosion
resistance and a reduced corrosion rate in concrete. Based on the results of this research,
SDA has great potential for its utilization as a structural material in transportation
infrastructures.
Carolyne A Namagga Department of Civil and
Environmental Engineering Colorado State University
Fort Collins, CO 80523 Spring 2010
v
ACKNOWLEDGMENTS
Her most sincere gratitude goes to her advisor, Dr. Rebecca Atadero, who tirelessly and
patiently devoted her time and resources to supervising her work. She appreciates the
advice, coaching, encouragement and guidance that she offered throughout her master’s
pursuit. Thank you! She also acknowledges and appreciates the committee members for
their contribution on this thesis.
The author gratefully acknowledges the spray dryer ash which was provided for this
project by the Platte River Power Authority and the funds provided for, for this research
by the Mountain Plains Consortium, a Federal Highway Administration University
Transportation Center. She also acknowledges the efforts of numerous undergraduate and
graduate research assistants including Kyle Wieghaus, Doug Allen, Catherine Oakleaf,
Dan Woodward, Neal Bohnen, John McWilliams, Hongyan Liu, and Thang Dao who
assisted with this project by helping to manufacture specimens and conduct testing.
To her family, she is grateful for the financial and social support that they offered
throughout this journey. She is grateful for the love and inspiration that they gave, that
provided a foundation for this success. To the friends, she acknowledges and thanks them
for their friendship and insight that they gave on various subjects especially related to this
school work.
vi
TABLE OF CONTENTS
1 Introduction ...................................................................................... 1
1.1 Background ...........................................................................................................1
1.2 Research Objectives ..............................................................................................4
1.3 Approach ...............................................................................................................5
2 Literature review .............................................................................. 7
2.1 Introduction ...........................................................................................................7
2.2 Concrete ................................................................................................................8
2.2.1 Application of Concrete .................................................................................9
2.2.2 Strength of Concrete ....................................................................................10
2.2.3 Concrete Durability .....................................................................................15
2.3 Cement ................................................................................................................20
2.4 Spray Dryer Ash .................................................................................................22
2.4.1 Types of Fly Ash ...........................................................................................23
2.4.2 Properties of Fly Ash ...................................................................................24
2.4.3 Utilization of Fly Ash ...................................................................................26
2.5 Fly Ash Concrete ................................................................................................27
2.5.1 Fly Ash and Concrete Strength ....................................................................28
2.5.2 Fly Ash and Concrete Bond Strength...........................................................30
vii
2.5.3 Fly Ash, Durability and Rebar Protection ...................................................31
3 Experimental Set-up ....................................................................... 34
3.1 Materials .............................................................................................................34
3.1.1 Spray Dryer Ash ...........................................................................................34
3.1.2 Other materials ............................................................................................35
3.2 Mix Design..........................................................................................................36
3.3 Compressive Strength Test .................................................................................37
3.4 Bond Strength Test .............................................................................................39
3.5 Durability (Freeze-Thaw) Test ...........................................................................42
3.6 Corrosion Test .....................................................................................................47
4 Results and Analysis ....................................................................... 50
4.1 Compressive Strength .........................................................................................50
4.1.1 Early Strength Gain (0 – 7days) ..................................................................50
4.1.2 Rate of Strength Gain...................................................................................51
4.1.3 Ultimate Strength .........................................................................................52
4.2 Concrete Shear Bond ..........................................................................................54
4.2.1 Mode of Failure ...........................................................................................55
4.2.2 Load-Slip Response ......................................................................................56
4.2.3 Bond Strength...............................................................................................61
viii
4.2.4 Peak Slip and Strain.....................................................................................62
4.2.5 Compressive Strength of Bond Test Specimens ...........................................63
4.3 Concrete Durability (Freeze-thaw) .....................................................................64
4.3.1 Weight Change .............................................................................................65
4.3.2 Freeze-thaw Resistance ...............................................................................66
4.4 Concrete Corrosion .............................................................................................69
4.4.1 Chloride Ion Penetration (Total Corrosion)................................................70
4.4.2 Rate of Corrosion activity ............................................................................73
5 Recommendations and Conclusions............................................... 75
5.1 Conclusions .........................................................................................................75
5.1.1 Compressive Strength ..................................................................................75
5.1.2 Bond Strength...............................................................................................76
5.1.3 Freeze-thaw (Durability) .............................................................................77
5.1.4 Corrosion .....................................................................................................78
5.2 Recommendations ...............................................................................................79
6 References ....................................................................................... 81
Appendix A: Mix Design ......................................................................... 87
Appendix B: Compressive Strength Results ....................................... 89
Appendix C: Bond Strength Results ....................................................... 91
ix
Appendix D: Freeze-Thaw Results ......................................................... 92
Appendix E: Corrosion Test Results ....................................................... 95
x
TABLE OF TABLES
Table 2.1: CDOT Concrete Classification (CDOT, 2008) ............................................12
Table 2.2: Fly Ash Classification as per ASTM C618..................................................24
Table 2.3: CCP and Fly Ash Produced/ Re-used (millions of tons) (ACAA, 2010) ....27
Table 3.1: Partial Chemical Composition of the Spray Dryer Ash (SDA) Used ..........35
Table 3.2: Concrete Material Specifications .................................................................35
Table 3.3: Summary of the PCA Absolute Volume Method for a cubic yard (27 ft3) ..37
Table 3.4: Non –Air Entrained Concrete Mixes (Design Strength 4500psi (31MPa)) .38
Table 3.5: Air-Entrained Concrete Mixes (Design Strength 4500psi (31MPa)) ..........43
Table 4.1: Summary of Bond Test Results ...................................................................57
Table 4.2: Average Results of Peak Loads (kips), Peak Slips (in) and Rebar Strains ..62
Table 4.3: 28- day mean Compressive Strengths (psi) for the Bond test specimen ......63
Table 4.4: Weight (lb) and weight change (%) specimens over N cycles ....................66
Table 4.5: Durability Factors and Relative Durability Factors .....................................68
Table 4.6: Average Corrosion Potentials of specimens ................................................71
Table 4.7: Probability of Corrosion (ASTM C876) ......................................................72
xi
TABLE OF FIGURES
Fig. 2.1: Overall CCP 2007 Production (ACAA, 2007) ................................................7
Fig. 3.1: Compression Testing Machine ......................................................................39
Fig. 3.2: Beam/ Rebar Specimen set-up .......................................................................40
Fig. 3.3: Schematic of Test Apparatus (ASTM A944-05) ...........................................40
Fig. 3.4: Schematic of Beam- End Specimen and Apparatus ......................................41
Fig. 3.5: Air Entrainment Testing apparatus (Volumetair) ..........................................43
Fig. 3.6: Concrete Prisms for Freeze-thaw testing .......................................................45
Fig. 3.7: Schematic of Apparatus for Transverse Frequency Test ...............................45
Fig. 3.8: Picture of Apparatus for Frequency Testing ..................................................45
Fig. 3.9: LabView Program ..........................................................................................46
Fig. 3.10: Timber forms and rebar for corrosion specimens ........................................48
Fig. 3.11 :a) Corrosion Specimens b) with Plastic dams and Epoxy .......................48
Fig. 4.1: Concrete Test Specimens at Failure ...............................................................50
Fig. 4.2: Early Compressive Strength of SDA Concrete ..............................................51
Fig. 4.3: Compressive Strength against Age of Concrete ............................................52
Fig. 4.4: Compressive Strength against SDA Concrete (for 28 and 56 days) ..............53
Fig. 4.5: Beam loaded indicating Shear Bond failure ..................................................55
Fig. 4.6(a): Load vs. Slip for beam (B1) (b): Load vs. Slip for beam (B2) .............59
xii
Fig. 4.6(c): Load vs. Slip for beam (B3) .......................................................................59
Fig. 4.7: Load vs. Slip for beams (B4, B5, B6) with 25% SDA ..................................60
Fig. 4.8: Load vs. Slip for beams (B7, B8, B9) with 50% SDA ..................................61
Fig. 4.9: Change in RDM (%) of SDA Concrete vs. Number of Cycles .....................68
Fig. 4.10: Total Corrosion vs. Concrete age .................................................................72
Fig. 4.11: Macrocell Current vs. Time of testing (Corrosion rate) ..............................73
xiii
LIST OF ABBREVIATIONS
ACI - American Concrete Institute
ASTM - American Standards of Testing Materials
CCP - Coal Combustion Products
C-S-H - Calcium Silicate Hydrate
CSU - Colorado State University
DF - Durability Factor
EPA - Environmental Protection Agency
EPRI - Electric Power Research Institute
FGD - Flue Gas Desulfurization
LOI - Loss On Ignition
PCA - Portland Cement Association
RDF - Relative Durability Factor
RDM - Relative Dynamic Modulus of Elasticity
SDA - Spray Dryer Ash
USGS - United States Geological Survey
1
1 INTRODUCTION
1.1 Background
This research is funded by the Mountain Plains Consortium, a Federal Highway
Administration University Transportation Center and it focuses on the potential for the
valuable utilization of Spray Dryer Ash (SDA) as a binding agent in concrete and
investigates its performance in concrete for structural and transportation applications.
SDA is a byproduct of electricity generation from coal and the scrubbing process used to
remove sulfur from power plant emissions. Based on the challenges associated with
disposal of all types of coal ash including SDA and the economic and environmental
costs linked to cement production, this research seeks to provide an environmentally
friendly and more cost effective concrete product by utilizing SDA in partial replacement
of cement in concrete. Cement production is a rather expensive venture and yet there is
an abundance of coal ash such as SDA and fly ash that is disposed off in landfills that
could be utilized positively.
Spray Dryer Ash, also known as Spray Dryer Absorber material, is a by-product of coal
energy production, obtained from the Flue Gas Desulfurization (FGD) process. The SDA
considered in this study is a self-cementing coal ash material obtained in Northern
Colorado at the Rawhide Power Station, managed by the Platte River Power Authority.
This material is unique to the mid-western and western regions of United States due to
the unique FGD process, commonly referred to as ‘Scrubbing’, used in the removal of
sulfur dioxide from the residual gases during the coal based energy production processes.
The SDA material is a highly alkaline residual fly ash that is contaminated with sulfur in
this scrubbing process (Hoffman, n.d.), disqualifying it from the Class C specification for
2
fly ash use in concrete (ASTM C618) that requires the sulfur content to be less than 6%.
With the exception of the high sulfur, the quality of the SDA produced is quite safe for
engineering use since it is very low in hazardous minerals (EPRI, 1998). Despite the
undesirably high sulfur content, this research will investigate its potential for beneficial
use in concrete.
Concrete, which is one of the most widely used construction materials, is a composite of
aggregate, cement and water. Concrete is produced at an estimated global rate of 5 billion
cubic yards per year. It is the second most widely consumed substance on earth, after
water (PCA, 2006). It has been used as one of the major construction materials in some of
the world’s largest infrastructure such as the Hoover Dam1, Petronas Towers2, Jin Mao
Tower3 and Dames Point Bridge,4 and is a major component in much of the highway
infrastructure being built. For example, 67% of the U. S Interstate highway and bridge
system has been built of concrete (NBI, 1994).
Concrete, together with reinforcement, is well known for its high strength development,
resistance to large magnitudes of loads, and small deformations when compared to
asphalt. When used in pavement construction, concrete provides an average useful life of
about 20 - 30 years before needing rehabilitation; compared to an asphalt pavement that
has a service life of 8 - 12 years (PCA, 2009a). Construction of a concrete pavement
requires a higher initial investment, but it has a very low maintenance cost as compared
11244ft long, 726.4ft high (2nd highest in the US) dam located on Colorado river at Arizona-Nevada border
2 1378 ft high skyscraper building in Kuala Lumpur, Malaysia
3 1371ft high skyscraper building, Shanghai, China
4 2 miles long bridge, spans St. John river, Jacksonville, Florida
3
to asphalt (PCA, 2009a). A high initial investment could be reduced by utilizing recycled
materials and waste products in substitution or replacement of cement. An extended
service life and reduced life cycle cost could also be actualized when these materials are
used for bridge construction (Daigle et al. 2006).
Portland cement production poses challenges of excessive energy usage and depletion of
natural resources. Cement is chemically manufactured from calcium, silicates and
aluminates in a process that releases carbon dioxide as a by-product into the atmosphere
and depletes the earth of mineral resources (Bye, 1999). In 2007, the world production of
cement was approximately 2.6 billion metric tons, with 127 million produced and
consumed within the United States (USGS, 2008). But when a ton of coal ash is used in
place of cement, 55 gallons of oil required to produce a single ton of cement is saved and
an equal amount of carbon dioxide that would be produced by the manufacturing process
is prevented from entering the Earth’s atmosphere (ACAA, 2009), hence making a
significant positive impact on the environment and preservation of natural resources.
Portland cement is a hydraulic material and it exhibits properties similar to the residual
waste (fly ash and SDA) obtained from coal energy production. Fly ash has produced
excellent results when used in concrete, and in many instances concrete mixes including
fly ash have outperformed standard concrete. There exist different types of fly ash and a
lot of research has been conducted to investigate its beneficial application in several
engineering industries. SDA is closely related to Class C fly ash. It is a relatively new
product that and has not yet been the subject of extensive study. However, based on the
previous success of Class C fly ash in concrete, it appears that SDA could provide a
4
suitable substitute for Portland cement and an environmentally friendly solution to the
concrete industry.
Fly ash has, for so many years, been a hazard to the environment. Several millions of tons
of fly ash and SDA are disposed off annually in landfills and ponds, raising concerns of
ground water contamination and health hazards to the environment (EPRI, 1998). Despite
the disposal challenge, these materials possess very excellent properties that produce
distinct benefits when added to traditional concrete mixes such as improved workability,
reduced permeability, increased ultimate strength, and reduced heat of hydration (King,
2005).
In an attempt to improve the environment and enhance the concrete industry, it is
essential to provide more sustainable and ‘green’ options as solutions and better
alternatives to existing products. Extensive research has been done in an attempt to make
concrete products more sustainable and cost effective. This research has included
recycling and utilizing valuable waste products such as car tires, glass, waste plastics,
slag and fly ash, which have been used in kilns to improve the cement manufacture
process and in concrete production. The utilization of SDA is another attempt at reducing
concrete’s carbon footprint on the environment thereby enhancing the sustainability of
transportation infrastructure constructed with concrete.
1.2 Research Objectives
The main objective for this work was to carry out preliminary research on four different
properties that are instrumental to the transportation industry, in order to demonstrate the
viability of SDA as a suitable partial alternative for cement in concretes. A more in-depth
5
study into these properties would be recommended. The research described in this thesis
will only demonstrate the suitability of SDA for use in transportation concretes by:
• Investigating and recommending quantities that would provide suitable results in
terms of compressive strength when SDA is used as a substitute for cement.
• Quantifying the bond strength behavior of SDA concrete through laboratory
testing.
• Studying the durability of SDA concrete with an emphasis on the freeze-thaw
performance of the concrete.
• Examining the corrosive behavior of rebar embedded in SDA concrete when
exposed to a chloride environment.
1.3 Approach
To meet the above objectives, a research team was assembled to carry out experimental
work on the SDA concrete. This work was carried out in the Concrete Laboratory and
Engineering Research Center at CSU through laboratory testing of specimens in
accordance with the relevant ASTM standards. Generally concrete samples with variable
quantities of SDA were prepared, cured and tested for their strength, durability and
corrosion properties. The results from these investigations are analyzed and detailed
within this thesis.
This thesis will provide an overview of previous studies done on SDA and fly ash in
concrete (chapter two), an outline of the experimental set-up of the research work
(chapter three), an analysis of the results (chapter four) and conclusions and
6
recommendations for further studies (chapter five). Design tables and raw data from
testing will be appended at the end of the thesis.
2 LITERATURE REVIEW
2.1 Introduction
Spray Dryer Ash (SDA) is one of the many residual p
production. Collectively these products have been termed as
(CCP). The other CCPs
There are numerous research
application of these products
an alternative product in replacement or (partial)
structural fill, and as
other sectors such as agriculture, mining, cement production as raw feed for the clinker
and waste stabilization
Fig. 2.1:
SDA material is a relatively new CCP tha
power plants built after 1978 employed the use of the Flue Gas Desulfurization (FGD)
Waste Stabilization
5%
Road base/Su
2%
Aggregate 2%
Gypsum Panel
Products 15%
7
LITERATURE REVIEW
Spray Dryer Ash (SDA) is one of the many residual products of co
production. Collectively these products have been termed as Coal Combustion Products
. The other CCPs include fly ash, FDG gypsum, boiler slag and
numerous research projects that have been conducted
these products, particularly with fly ash. Engineers have utilized fly ash as
native product in replacement or (partial) substitution of cement in concrete,
and as road base aggregates. CCPs have also found
other sectors such as agriculture, mining, cement production as raw feed for the clinker
and waste stabilization, as illustrated in Fig. 2.1.
Fig. 2.1: Overall CCP 2007 Production (ACAA, 2007)
SDA material is a relatively new CCP that has been in existence since the 1980s when
power plants built after 1978 employed the use of the Flue Gas Desulfurization (FGD)
Structural
Fills/Embankments
Mining Applications
12%
Raw Feed for
Clinker 9%
Waste Stabilization
Road base/Su-base
Aggregate 2%
Gypsum Panel
Products 15%
Others 10%
roducts of coal-based energy
Coal Combustion Products
and bottom ash.
conducted on the engineering
. Engineers have utilized fly ash as
cement in concrete, as a
found application in many
other sectors such as agriculture, mining, cement production as raw feed for the clinker
(ACAA, 2007)
t has been in existence since the 1980s when
power plants built after 1978 employed the use of the Flue Gas Desulfurization (FGD)
Structural
Fills/Embankments
19%
Concrete/ Concrete
Products 26%
8
process to limit the release of sulfur dioxide in compliance with the Clean Air Act (EPRI,
2007). Therefore, in comparison to fly ash, there has not much research on the beneficial
use of SDA. For this reason this literature review will include previous work with SDA
when available, but will also draw from previous work with fly ash in concrete.
Fly ash has found very positive usefulness in the concrete industry due to its pozzolanic
behavior in forming cementitious bonds. Concrete is characteristically defined by the
strength of these cementitious bonds created between the aggregates. The strength of
these bonds is determined by the nature and type of pozzolanic material used within the
concrete.
A Pozzolan is an alumino-siliceous material which in the presence of water reacts with
calcium hydroxide to form compounds possessing cementitious properties. Generally,
they have the ability to set at room temperature without the use of any retarders or
accelerators/ superplasticizers (King, 2005). Several types of pozzolans exist, in addition
to fly ash, such as silica fumes, calcined clay (metakaolin), ground granulated blast
furnace slag (slag) and of recent production SDA. The pozzolans can be acquired
naturally when mined directly as volcanic tuffs, manufactured as metakoalin, retrieved as
an industrial by-product or acquired from burning rice hull (Malhotra, 1986). This
research focuses only on SDA and its use in concrete.
2.2 Concrete
Concrete is a composite material that is comprised of aggregates and any binder/
pozzolan mixed together in the presence of water to form a hardened structure of durable
quality and strength. The most commonly used binder is Portland cement. Other binders
9
include pozzolans such as fly ash (and SDA), silica fumes, ground granulated blast
furnace slag, and metakoalin can be used in complete substitution or partial replacement
of Portland cement (Malhotra, 1986).
Some admixtures such as super-plasticizers or retarders can be added to any concrete to
facilitate
or retard the hydration reaction process of the concrete. When these admixtures are added
to the concrete, they modify the concrete forming different types that are specific to the
user’s application. Such modified concrete could be referred to as high strength, high
performance, shotcrete (Garshol et al. 2007), and many other names, such as asphalt
concrete, lime concrete and glass concrete (Poutos et al. 2008) when the cement or
aggregates are substituted for by other materials of similar properties.
2.2.1 Application of Concrete
Concrete has been widely used in the construction/ highway industry. An estimated
global rate of 5 billion cubic yards per year of concrete is produced (ACAA, 2009). In the
US, concrete has found a great application in bridge and pavement infrastructure.
Presently more than 50% of the bridges in the US are constructed out of prestressed
concrete (TRB, 2009).
Concrete has been used in isolation, referred to as mass concrete, or together with steel
materials to form reinforced or pre-stressed concrete. It has also been used in masonry to
manufacture concrete blocks or pavers and other concrete products such as pipes,
culverts, and highway barriers (PCA, 2009b). Concrete has been used in the design and
construction of structural elements such as columns, beams, slabs, piles/caissons, shear
10
and retaining walls in buildings and piers, towers, and pavements in highway
construction. It has been used in the construction of other structures such as dams,
swimming pools, water tanks and silos. Concrete gains its popularity, in many instances,
from its high strength development and its high resistance to impact and bending.
‘Modified’ concrete has been used widely in bridge/ highway construction and in other
applications that require early strength development and fast-setting of concrete. For
example
glass concrete has been shown to improve the thermal insulation of buildings (Poutos et
al. 2008). Another example is limecrete (lime used with concrete) has been used in
flooring systems to enhance under-floor insulation and eliminate floor dampness in the
interiors of the building. The Limecrete is used in areas that are not exposed to weather
conditions. Shotcrete (concrete sprayed at high pressures) is normally used in tunneling,
in areas where seepage is a concern, areas with high water tables and against vertical soil
or rock surfaces (Garshol et al. 2007). In a bid to conserve the environment sustainable
materials such as fly ash have been utilized in modifying the concrete. Concrete itself has
been recycled and utilized as aggregate in new concrete or in a road sub-base layer
(Buck, 1977).
2.2.2 Strength of Concrete
2.2.2.1 Compressive Strength
Concrete members are designed based on the concrete’s compressive strength. When
improperly designed concrete members will ultimately fail due to the occurrence of
11
significant tensile loads. The presence of smaller tensile loads in concrete will induce
cracks, which may cause serviceability limit states to be reached.
Several classes of concrete strength are utilized based on its intended application. For
example, the strengths will vary depending on whether concrete is for non-structural
(general) use or structural applications such as drilled piers, concrete pavements (decks),
girders, or repairs. Concrete may also be specified to achieve high strength or early
strength requirements. The typical range of strength used for conventional reinforced
concrete is 3000 – 4000 psi (21 – 28 MPa) while that used for prestressed (high strength)
concrete is 5000 – 6000 psi (35 – 41 MPa). Higher concrete strengths provide for a
reduction in weight of the members and they experience smaller volume changes.
Volume changes can affect the proper functioning of the members, for example causing a
loss of prestress in prestressed concrete members (Tonias, 2007).
Strengths required for transportation use tend to range between 4000 – 6000 psi (28 – 41
MPa). The AASHTO LRFD specifications (1994) provide minimum requirements for the
classes of strength to be used for different applications. The Colorado Department of
Transportation (CDOT) has narrowed down the AASHTO specifications to suit Colorado
environmental conditions. CDOT has the concrete classes shown in Table 2.1. The
classes specify the required field compressive strength at a given age of the concrete.
12
Table 2.1: CDOT Concrete Classification (CDOT, 2008)
Concrete Class
Required Field Compressive strength (psi)
Cementitious content: Minimum or range (lbs/yd3)
Air content range (%)
Water cementitious
ratio: max / range
B 4500 at 28 days N/A 5 - 8 0.45
BZ 4000 at 28 days 610 N/A 0.45
D 4500 at 28 days 615 – 660 5 - 8 0.44
DT 4500 at 28 days 700 5 - 8 0.44
E 4200 at 28 days 660 4 - 8 0.44
H 4500 at 56 days 580 – 640 5 - 8 0.38 – 0.42
HT 4500 at 56 days 580 – 640 5 - 8 0.38 – 0.42
P 4200 at 28 days 660 4 - 8 0.44
S35 5000 at 28 days 615 – 720 5 - 8 0.42
S40 5800 at 28 days 615 - 760 5 - 8 0.40
S50 7250 at 28 days 615 - 800 5 - 8 0.38
Each of the classes (Table 2.1) is designated for a specific purpose. For example Class B
is an air entrained concrete and is utilized for general use while Class DT is used for deck
resurfacing and repairs. The final three classes in the table, Class S35 – S50 are specified
for high strength use in structural applications such as bridge girder and pier construction
(CDOT, 2008). It is important that the concrete utilized has a composition which limits
the effects of forces such as shear, bending, torsion and deformation phenomena such as
concrete creep, fatigue, shrinkage or thermal expansion, and yet maintains sufficient
strength for the duration for which the structure was designed for. This duration is usually
10 – 20 yrs for concrete pavements (Tonias, 2007).
13
2.2.2.2 Bond Strength
For reinforced concrete to function as a structural material it is important to maintain
composite action, which requires the transfer of load between the concrete and steel.
This ability to transfer load is referred to as the bond. The load transfer between concrete
and rebar occurs through friction (local bond-slip relationship) and the mechanical
interaction between the reinforcing bar and surrounding concrete. Mechanical interaction
is the dominant mechanism of load transfer at small to moderate slip levels but friction
dominates at extreme slip levels and immediately upon load reversal. For reinforced
concrete structures subjected to moderate loading, the bond stress capacity (mechanical
interaction) of the system exceeds the demand, hence very small movements are observed
between the reinforcing steel and surrounding concrete. However for systems subjected
to severe loading, localized bond demand may exceed the bond capacity and result in
localized damage and significant movement between the steel and concrete (Lowes et al.
2004).
Experimental investigation indicates that the bond response is determined by a number of
parameters and system variables. These parameters include composite material state, steel
and concrete material properties (compressive strength, tensile strength and steel yield
strength), steel ratios and thickness of concrete cover. The bond strength response is
characterized as a function of compressive strength and bar size. It is determined by slip
damage of concrete at the rebar-concrete interface. Loss of bond strength typically
results from the development of localized cracks or due to concrete –rebar shear. Bond
failure is due to tensile cracking or shearing of concrete (Lowes et al. 2004). The
14
relationship between the bond strength (τ) and compressive strength (fc) can be defined
(Eligehausen et al. 1983) by
for ( 1 3 12 ) (2.1)
The standard (ACI, 2008) simplifies the bond strength relationship above by equating
β =12 and a constant, k that is dependent on the serviceability requirements for the
different flexural members.
Under initial loading the bond stresses are largest near the surface and tend to zero at the
embedded end. As the loaded reinforced concrete approaches its bond failure, the stresses
along the reinforcing bar become uniformly distributed. This maximum bond strength
(τmax) given below (2.3) is computed from the equilibrium relationship (2.2) between
maximum (bond/ tensile) load applied to the bar and the internal bond slip load
τ (2.2)
and is defined as a function of bar diameter (ds), development (slip) length (ls) and the
steel’s yield strength (fy) (Nawy, 2000):
τ
! (2.3)
Experimental investigations have considered the response of bars ranging in size from
No. 6 to No. 10. Variables such as the cyclic load history, type of concrete confinement,
level of concrete damage and strain history will also determine the maximum strength
attained (Lowes et al. 2004).
Consequently it is important to have sufficient anchorage and flexural bond length that
will provide good development of local bond slippage, a well defined bond zone length
15
and minimize cracking in the concrete. As a result, the reinforcement should be able to
attain its yield strength without failure of the bond (Nawy, 2000).
2.2.3 Concrete Durability
There are numerous durability concerns faced by concrete and these include alkali-
aggregate reaction; chemical attack by sulfates, chlorides and other aggressive chemicals;
freezing and thawing; and severe exposure conditions (Ramesh et al.1997). Concrete
should be designed to resist weathering action, abrasion and chemical attacks, while
maintaining its engineering purpose. When these concerns are not addressed properly,
they can cause serviceability problems, concrete deterioration and induce corrosion of the
rebar imbedded within the concrete (Ramesh et al.1997). This thesis will focus on the
freeze-thaw challenge and rebar corrosion problem in reinforced concrete.
2.2.3.1 Freeze-thaw
Concrete is most vulnerable to frost during its early ages (first week) due to relatively
high capillary water content and its low strength. It is essential to protect the premature
concrete from the initial freezing cycles. When exposed to very low temperatures, long
periods of freezing, and/or subjected to frequent cycles of freeze-thaw concrete is at great
risk of durability failure if no measures are taken. Damage arises from the freezing of the
pore water within the concrete that is accompanied by its expansion. In mitigating this
effect air entrainment admixtures are utilized to provide extra air voids that provide space
for the freezing water to expand into, without causing damage to the concrete
(Richardson, 2002).
16
The amount of air content required depends on the volume of frozen water to be
accommodated, which is a function of the permeability and porosity properties of the
concrete. It is minimized by lowering the water-cementitious materials ratio used for the
concrete (Richardson, 2002). The amount of air required to provide adequate freeze-thaw
resistance is also dependent on the nominal maximum size of aggregate and the level of
exposure. The required air content will decrease with an increase in the maximum
aggregate size due to a reduction in the mortar content. Concrete mixes with a maximum
aggregate size of ¾ in (20 mm) containing air entrainment are designed to produce an air
content approximately equal to 4 – 6% of the concrete volume (ACI 211, 1991).
Concrete subjected to alternate cycles of freezing and thawing experience mainly two
types of deterioration namely surface scaling and internal cracking. Scaling is the most
frequently observed form of deterioration and it is the progressive loss of small particles
of mortar on a concrete surface subjected to alternate freeze-thaw cycles, hence exposing
the coarse aggregates. Cracking is formed due to the internal pressures generated by the
action of frost within the hardened concrete. The resistance of the concrete to frost is
dependent on various factors affecting the aggregate-paste interface such as the strength
of the interface, degree of saturation, creep and the pore structure of the paste (Pigeon et
al. 1995).
Internal cracking is uncommon nowadays since most of this concrete has been protected
by the use of air entrainment, but is typical in the laboratory for concrete specimens that
are fully saturated. The test method describe in ASTM C666 ascribes to measurement of
the fundamental frequency (and relative dynamic modulus of elasticity), whose reduction
17
is an indicator of the extent of internal cracking in concrete specimens (Pigeon et al.
1995).
This reduction in the measurement can also be influenced by the surface scaling when the
concrete specimens are subjected to freezing in the soaked water. The transverse
fundamental frequency is a function of the mass of the specimen; heavier specimens will
have a higher frequency. Subsequently the scaling effect, when severe, could
significantly reduce the mass of the specimen hence reducing the durability factor below
60% without showing any significant micro-cracking (Pigeon et al. 1995).
The fundamental frequency reflects the internal disruptions within the concrete due to
deficiencies in the air-void characteristics or nature of aggregates while a weight loss is
due to the scaling effect. A reduction in fundamental frequency can occur without a
decrease in the weight loss and vice visa. ASTM C260, C494 and C1017 require that the
relative (in relation to reference/ Control concrete) durability factor of air entrained
concrete with admixture under investigation should be at least 80%, but no minimum
durability factor or other requirements are given in the ASTM standards. Wang (2009) in
his research defined a good durable low permeability concrete as one that attains a
durability factor of at least 85 percent.
The introduction of air entrainment in concrete involves a certain sacrifice in concrete
strength though it enhances its durability. Checks and controls on selected materials are
essential to ensuring that the desired strength for the desired design life in the given
exposure conditions is attained. Design guides have also made adjustments to the mix
18
proportions to ensure a feasible compromise on the strength and durability of concrete
(Kosmatka et al., 2002).
2.2.3.2 Corrosion
The corrosion of steel rebar is the primary and most costly form of deterioration
experienced by reinforced concrete bridge structures. In the United States, maintenance
and rehabilitation costs for deficient bridges are very high and are measured in billions of
dollars. (Wipf, 2006)
The risk of corrosion of steel rebar can be minimized if a sufficient depth of concrete
cover is provided for the steel. It can also be minimized if the concrete is well designed
since concrete is highly alkaline (pH ~12) and can provide a protective layer for the
embedded steel. However, when the concrete is subjected to corrosive conditions,
oxygen, chemicals such as chlorides, sulfates, carbonates and moisture can ingress
through the pores to reach the rebar surface and alter the alkalinity of the concrete and
cause the breakdown of the passive layer hence causing corrosion of the steel (Bavarian
et al. 2006).
Ingress of chlorides such as sodium chloride (de-icing salts) is one of the major causes of
steel rebar corrosion in concrete utilized in the transportation industry. The corrosion
deterioration would begin with the penetration of chloride ions into the concrete, then the
breakdown of the passive layer, more acute corrosion of the rebar, micro cracking and
eventually spalling of the concrete (Bavarian et al. 2006). The breakdown of the passive
layer can be brought about by many other interactions such as structural, physical,
chemical and environmental considerations. For example a structural failure of the
19
reinforced concrete can create cracks within the concrete that would eventually expose
the embedded rebar to corrosion. When the rebar is exposed to the environment the steel
is subjected to oxidation and ferrous ions (rust) are formed, as given by the equation
(2.4):
2Fe$% & 3($) Fe$O+ & 6H% (2.4)
The penetration of the chloride ion among other properties such as the resistance to
sulfate attack and alkali-silica reaction, are all functions of the permeability of concrete.
It is important to ensure that the concrete surrounding the embedded concrete has the
ability to protect the reinforcing steel from corrosion. The major factor that should be
considered in designing a corrosion resistant concrete is the water-cementitious ratio,
which governs the permeability of concrete. The cement /material specification also plays
a significant role in determining the permeability of the concrete.
There are number of tests that can be carried out to investigate the nature and extent and
behavior of corrosion activity in concrete subjected to severe environments. Some of
these tests include acid-chloride content (ASTM C1152); measures the chloride content
in concrete, Polarization resistance (ASTM G59); measures corrosion rates,
electrochemical impedance spectroscopy (ASTM G106); measures concrete resistivity,
Chloride diffusion (ASTM C1556); measures relative diffusion rates of chlorides. This
research will only focus on the studying the effect of admixtures such as SDA may have
of the corrosion behavior of concrete. This study will be conducted in accordance to
ASTM G109 and reference made to ASTM C876 that will illustrate the probability of the
formation of corrosion cells on the reinforcing steel (ASTM C876).
20
There is lot of research done to mitigate corrosion through increased concrete coverage,
use of admixtures, reduced permeability concrete, migrating corrosion inhibitors and
replacement of steel rebar with alternative materials (Sharp, 2004).
2.3 Cement
Cement is composed of free lime and siliceous and aluminous materials (pozzolans),
which in the presence of water, will chemically react with the calcium hydroxide released
by the hydration process to form a cementitious paste that binds the inert materials in the
concrete (ASTM C125). It is manufactured industrially by heating a homogeneous
mixture of limestone and clay materials in a kiln at a temperature of 2642 degrees
Fahrenheit (Bye, 1999).
The most commonly produced and utilized pozzolan/cement is Portland cement (Bye,
1999). It is categorized (ASTM C150) into five types I – IV, depending on the ratios of
the material compositions in the cement. The different types of cement have been
formulated to offer slightly different characteristics, for example Type III is formulated to
have improved early strength gain.
2.3.1 Cement versus Fly Ash
Unlike cement, which is a manufactured product, fly ash is a waste product of coal-based
energy production. Both cement and fly ash exhibit similar reaction compounds and
characteristics but differ in the amounts of their constituents. The compounds in Portland
cement, in the presence of water, will react to form calcium silicate hydrate gel (C-S-H)
21
or calcium aluminate hydrate gel (both cementitious material) which bind the inert
materials together (Neville, 2006).
The standard cement hydration reaction equation is given by (Neville, 2006):
When fly ash is incorporated in the concrete matrix above, the lime produced will react
with the pozzolanic compounds present in the fly ash to produce the same C-S-H
compounds formed by the hydration of cement.
The pozzolanic reactions involving fly ash vary considerably with the type of ash used.
The silica content and the calcium oxide present in the fly ash will determine how much
fly ash reacts in the matrix. The pozzolanic activity of the fly ash is also dependent on
other parameters such as its unburned carbon content and its fineness (Ramesh et al.
1997). The amorphous amino-silica compounds in the fly ash will further react with the
free lime, over time, to form more C-S-H bonds/gel. Over time, the fly ash/Portland
cement matrix will produce more C-S-H gel than that produced by Portland cement alone
hence providing additional cementitious products which impart additional strength to the
concrete.
Generally pozzolans such as fly ash, in the presence of water, will react in a similar
hydration reaction as Portland cement. Fly ashes containing high amounts of lime, such
Portland Cement
Water C-S-H Lime
Portland Cement
Fly Ash Water C-S-H Lime
Fly Ash Lime (more) C-S-H
22
as the Class C type, are capable of setting independently when mixed with water, hence
making it self-cementing (Berry et al. 2009).
Its independent use is generally not recommended because the pozzolanic reactions are
much slower than the cement hydration reactions and would affect the early strength and
rate of strength gain significantly.
2.4 Spray Dryer Ash
Spray Dryer Ash is a residual material of coal-based energy production, obtained from
the Flue Gas Desulfurization process (FGD), commonly referred to as ‘Scrubbing.’ This
process removes sulfur dioxide from the power plant emissions and is accomplished by
adding calcium hydroxide (lime) to the flue gases (contaminated with sulfur dioxide),
while at the same time the heat of the flue gases assists in drying the reaction products
(Babcook et al. 1978). These products later collect with the fly ash produced and form a
unique material that has been termed as a SDA.
The fly ash is produced from burning pulverized coal in a coal-fired boiler furnace. The
fine-grained waste product produced is then carried off in the flue gas and is collected out
from the flue gas using electrostatic precipitators (bag houses) or mechanical collection
devices (cyclones). About 30 – 80 percent of all the ash produced leaves the furnace as
Fly Ash Water C-S-H (Free) Lime
Dry Reaction Products Fly Ash Spray Dryer Ash
23
fly ash, depending on the boiler furnace used in the energy production (Babcook et al.
1978). The general flow of the process resulting in fly ash is illustrated below:
Because SDA is collected together with fly ash it is similar to fly ash in many ways and
most closely resembles Class C fly ash, which is predominant in the mid-west and
western regions of the U.S. It is a relatively new product and limited research has been
done on its application. The present research is based on the hypothesis that it will
perform similarly to Class C ashes therefore the following sections will address content
on fly ash used in concrete which will be used for comparison with SDA characteristics.
2.4.1 Types of Fly Ash
Several types of fly ash exist, all dependent on the type of coal and the coal combustion
process, which determine the chemical composition of the fly ash. The different types
vary mainly in the amount of calcium, silica, alumina, and iron they contain.
These have been classified (ASTM C618) into two basic classes:
Coal Power Plant Coal Pulverizer
Boiler FurnaceFlue Precipitator
FLY ASH
24
Class F: This is obtained from burning anthracite and bituminous coal. This fly ash
contains less than 10% lime (CaO), hence requires a supplemental cementing agent such
as Portland cement, quicklime or hydrated lime in order to react efficiently (King, 2005).
When Class F Fly ash is subjected to a highly alkaline environment such as Sodium
hydroxide or Sodium silicate, a new material known as a geo-polymer is formed
(Tempest et al. 2009).
Class C: This fly ash is obtained from burning younger lignite and sub-bituminous coal.
It exhibits self-cementing properties because it contains a higher content of lime, more
than 10% (King, 2005). Unlike Class F, Class C fly ash does not require an activator
since it contains higher amounts of alkali (King, 2005).
Based on its chemical composition, the Spray Dryer Ash being used in this research
would ideally be categorized as a Class C fly ash except for its high sulfur (>6%) content.
Table 2.2 compares the ASTM requirements for the different types of fly ash.
Table 2.2: Fly Ash Classification as per ASTM C618
Component Moisture SiO2 Al2O3 Fe2O3 SO3 LOI
max. % min. % max. % max. %
Class F 3 70 5 6
Class C 3 50 5 6
2.4.2 Properties of Fly Ash
Fly ash obtained from different coal plants is highly variable in its properties and is
dependent on the coal combustion process that was used. Hence fly ash is usually defined
25
in terms of its chemical and physical properties. The most essential properties that affect
the fly ash’s reactivity include its fineness and Loss on Ignition (LOI) (King, 2005).
The Loss on Ignition (LOI) is a measure of the unburned carbon content in the fly ash
and it greatly influences the chemical characteristics of the fly ash. The carbon content
(LOI) present in the fly ash can be approximated physically by observing the color of the
fly ash. The color varies from gray (Class C) to black (Class F). The lighter the color, the
lower the carbon content or unburned carbon (Ramesh et al., 1997). The ASTM C618
specification limits the LOI to a range of 3 - 6%. Fly ash containing larger amounts of
unburned carbon would reduce the effectiveness of air entrainers and decrease the
workability of the concrete, hence impairing reactivity and strength development. Higher
water content and more air entrainer would be required to maintain the required
workability and air content (Ramesh et al. 1997)
The fineness of fly ash is a key property in determining its reactivity and strength
characteristics. The fine particle size reduces the porosity of the concrete and increases
the volume-to surface area ratio, which is needed for the pozzolanic reaction. The
fineness of the fly ash, however, does affect the amount of air entrained in the concrete. It
will increase the demand for the air entrainer needed to provide a target air content. All
fly ashes have a particle size less than 0.075 mm and are mostly amorphous in nature.
The Class C type fly ash is generally coarser than the Class F fly ash. The specific gravity
usually ranges between 2.1 and 3.0. Increased particle fineness has been shown to
increase the pozzolanic activity of the fly ash (Ramesh et al., 1997).
26
The proportions of the chemical constituents present in fly ash define the type of fly ash
and determine the extent of its pozzolanic activity. Sufficient amounts of silica (SiO2),
alumina (Al2O3) and iron oxide (Fe2O3) are needed to react with lime, in the presence of
water. The sum of these oxides must reach the required minimum of 50% for Class C and
70% for Class F. Calcium oxide (CaO) is another significant oxide that affects the
pozzolanic activity of the fly ash. It governs the performance of the fly ash in concrete,
which is influenced by the amorphous nature of the fly ash and is responsible for the
creation of reactive (free) lime. Sulfur trioxide (SO3) is another oxide that great affects
the early strength development of the fly ash. The higher the sulfate content, the higher
the resultant strength. A maximum of 5% is permissible in the fly ash so as to avoid
excess sulfates that may contribute to disruptive sulfate attacks (King, 2005).
The above physical and chemical properties of fly ash do provide improved workability,
reduced permeability, increased ultimate strength, reduced bleeding, improved surface
finish and reduced heat of hydration when a fly ash- cement matrix is used in concrete
(Ramesh et al., 1997).
2.4.3 Utilization of Fly Ash
Fly ash has been used in several engineering applications such as structural fill, waste
stabilization and solidification, soil stabilization, aggregate and filler material, road sub-
base, raw feed for cement clinkers, production of geo-polymer materials, mine
reclamation, grout and as partial replacement/ substitution of cement (Ramesh et al.,
1997). However, the amount of fly ash produced is still much greater than the amount of
fly ash that is put to beneficial use. Millions of tons of coal combustion products are
27
produced annually but less than 43% of the products are used beneficially. Utilization of
fly ash in concrete offers environmental and cost benefits by reducing the demand for
virgin materials and minerals that are used in the manufacture of cement, the amount of
carbon dioxide released in the atmosphere through the cement manufacture process, and
the amount of coal ash disposed of in landfills (ACAA, n.d.). Table 2.3 illustrates the
utilization of coal ash (CCP) in the recent past:
Table 2.3: CCP and Fly Ash Produced/ Re-used (millions of tons) (ACAA, 2010)
CCP
produced
CCP
re-used
Fly ash
produced
Fly Ash
re-used
%age re-
used
2006 125 54.2 72.4 32.4 45%
2007 131 56 71.7 31.6 44%
2008 136 60.6 72.5 30.1 42%
These statistics indicate an increasing fly ash disposal challenge that requires an efficient
solution. The concrete industry seeks to contribute to the solution by utilizing fly ash in
its applications. One incentive for utilizing fly ash in amounts greater than 25% is that it
would classify the concrete a LEED certified product (PCA, 2009).
2.5 Fly Ash Concrete
Fly ash mixed with concrete has shown results of increased strength and durability of the
concrete. Its utilization in the US stretches back to 1929 when it was first used on the
Hoover Dam (Smith, 2006). Concrete with fly ash can be produced to achieve desired
strengths at various ages, with a given water-cementitious ratio, aggregate size, air
content and slump. Concrete with fly ash has been widely used in the highway industry.
28
Much of it is air entrained since the fineness of the fly ash provides a challenge for the
concrete to maintain sufficient air voids needed for the freeze-thaw cycles (Ramesh et al.
1997).
In some instances 100% fly ash (Class C) concrete has been produced and has been found
to meet acceptable concrete standards. It has been used on a number of projects which
entailed the construction of foundation walls and footings, floor slabs and manufacture of
precast panels. However, its use has not yet found much acceptance in the construction
industry due to its highly sensitive handling and quality control, and challenges
experienced in adhering to the specified batching procedures. The order in which the
materials are introduced into the mixture and the duration of the mixing process is of vital
importance in ensuring proper setting of the concrete (Berry et al. 2009).
Fly ash concrete has been acknowledged as a ‘green’ product. Some states like California
have recognized the benefits of fly ash concrete and its Department of Transportation
(Caltrans) requires all highway projects to use fly ash to blend all concretes (Maggenti,
2009).
2.5.1 Fly Ash and Concrete Strength
Concrete strength, defined by its compressive strength, is affected / determined by a
number of factors such as the water-cementitious ratio, setting time, workability, curing
and pozzolanic activity - dependent on the type of pozzolan used. For example utilization
of fast setting cement will reduce the setting time and provide for its early strength
development. Other pozzolans such as fly ash have been used and have provided
enhanced properties and added benefits in concrete.
29
The effects of fly ash (both Class C and Class F) can be recognized with as little as 20%
fly ash replacement of cement in the concrete. This amount can increase the setting time
of concrete by about 1 to 2 hrs, and doubling this amount could further increase both
initial and final setting times (Ramesh et al. 1997). Several studies have been done to
investigate the influence fly ash has on the strength (early and ultimate) of concrete, but
few studies have been done with SDA. Hence guidelines for the usage of fly ash (and its
derivatives, SDA) are limited to Class C and Class F types. The ACI guidelines limit the
use of Class F fly ash to 15 – 25% and Class C fly ash to 20 - 35% (ACI, 1996)
replacement of cement in the concrete.
Crouch et al. (2009) has made attempts to investigate a 50% usage for Class F fly ash and
their research findings indicated an increment in the ultimate strength despite a reduced
early strength development in the concrete. Lower early strength development is the main
set-back experienced when using Class F fly ash in concrete. Despite this limitation, its
utilization in concrete could be enhanced by activating it with an alkali, which helps
improve the hydration process. Such concrete could be referred to as geo-polymer/ alkali-
activated concrete. In some instances glass aggregates (recycled glass) could be used to
improve the hydration process instead of alkalis. The recycled glass not only acts as filler
material in the concrete but also plays a role in the strength development (Trejo et al.
2004).
The percentage of Class C fly ash typically used in structural concrete is 20 - 35% (ACI,
1996) though in some instances 35 - 100% Class C Fly ash has been used to replace
cement. In 1988 it was used to replace up to 70% of the cement in a highways project in
North Dakota and in 1989 it was used for concrete roads and parking lots (Golden et al.,
30
2003). The concrete was designed for a target strength of 3500psi, and its 35 day strength
was found to have exceeded the target.
Berry et al. (2009), in their research confirmed that concrete using only Class C fly ash as
the cementing agent can exhibit outstanding performance in terms of compressive
strength behavior. Early strength gains, in excess of 4000psi (27.6MPa) were achieved
and strength of over 8000psi (55.2MPa) was attained after 84 days. Its application is
witnessed on the Orchard Gardens (2005)5, a $6.5 million project that utilized 100%
Class C fly ash in the community barn foundations and 35% Class C fly ash in the rest of
the foundations. Kumar et al. (2007) also found that 50 - 60% Class C fly ash
replacement was adequate to meet the strength requirements for concrete pavements.
Class C fly ash has an accelerated rate of chemical reaction when water is added due to
the high calcium content. At elevated curing temperatures the setting times could be
reduced and an increase in the early strength development would be attained. On the
other hand, the long-term strength and durability of concrete cured at elevated
temperatures is still suspect (Elsageer et al. 2009).
2.5.2 Fly Ash and Concrete Bond Strength
Bond strength is a measure of interaction between the steel rebar and the concrete in
terms of direct shear. When loaded the concrete surrounding the rebar induces stresses
onto the rebar’s lateral surface creating shear/ bond stresses along the bar. It is an
important structural design property that is significant to the effectiveness of the steel
reinforcement in concrete and enables for the proper design and performance of
5 Orchard Gardens, http://www.greencommunitiesonline.com
31
reinforced concrete. Structures, concrete pavements and bridges are designed based on
the interactive behavior of the rebar with the concrete (Tonias, 2007).
Strength of concrete is of paramount importance in determining the effective
performance of the structure and should not be compromised by the presence of a weak
bond. Over the years research has been done addressing this challenge and some attempts
have been made to enhance the properties of the concrete by utilizing energy efficient
materials such as fly ash.
Considering the smaller particle size of the fly ash (and SDA) it is presumable that
utilization of fly ash in concrete would provide greater shear bond with the rebar. A
number of studies carried out, though indicate relative bond strength produced with fly
ash use. Chang et al. (2009) investigated the shear bond behavior of fly ash based geo-
polymer concrete beams and discovered that the bond strength was closely related to that
of normal concrete beams. Cross et al. (2005) had a similar finding that showed the
specimen containing 100% fly ash performed similarly to the plain reinforced concrete.
Experimental assessment of the bond strength of concrete has mainly used the
conventional pull-out test (ASTM A944) to investigate the strength. Other test methods
such as the direct tension pull-out test method and the beam-splice test method have also
been used as alternatives or for comparison purposes.
2.5.3 Fly Ash, Durability and Rebar Protection
Durability and corrosion of the reinforcement in concrete are closely linked since failure
of one would inherently affect the other. For example the wearing out of the concrete
cover would expose the rebar to the atmosphere and lead to corrosion. Durability of
32
concrete is defined as the ability to withstand chemical attack (chlorides, sulfates and
other corrosive materials), weathering action (frost, rain and high humidity) and abrasion
while maintaining its desired engineering properties (PCA, 2002). Corrosion, on the
other hand, is the oxidation/ rusting of the rebar caused by the ingress of water or
chemicals (such as chlorides, sulfates and carbonates) onto the rebar embedded within the
concrete (PCA, 2002).
Concrete utilized for pavement construction is usually exposed to inclement conditions
and is very susceptible to deterioration. It is important to protect the embedded rebar and
design the concrete to be able to withstand severe environmental conditions, for a long
time, without significant deterioration. Freeze-thaw and steel corrosion properties of
concrete are vital concerns in the maintenance and longevity of transportation
infrastructure and therefore help define the scope for this thesis.
In addition to providing a sufficient concrete cover, innovative methods/ designs should
be introduced to make concrete more resistant to attack and less porous to any ingression.
Previous studies done show that the utilization of fly ash in concrete provides improved
impermeability within the concrete, though other chemical effects could cause its
deterioration. In his thesis, Burden studied the effects of curing on the carbonation and
permeability of high volumes of Class C and Class F fly ashes, and discovered that the
rate of carbonation increased and permeability decreased over time with an increment in
the amount of fly ash used (Burden, 2006). He suggested that carbonation-induced
corrosion could be offset by extending the moist curing time and increasing the concrete
cover.
33
When not exposed to any chemical environment, fly ash concrete serves as a very durable
material since its water permeability and void content are reduced with an increase in fly
ash used (Crouch et al. 2009). This is due to the pore refinement that is provided by the
fineness of the fly ash. The fly ash concrete matrix is also able to reduce the permeability
to chlorides, and sulfates and carbon dioxide penetration in concrete, hence reducing
corrosion of reinforcement bars embedded within and improving the durability of the
concrete (Ramesh et al., 1997).
In the past century, a new method was introduced to make concrete exposed to freeze-
thaw conditions more resistant. Air entrainment admixtures were created and are
presently being incorporated into transportation concretes. The introduction of the
admixtures produces small air bubbles which allows for flexibility in the freeze-thaw
cycles that the concrete would be subjected to. Similar to the admixtures, the use of fly
ash has been observed to produce durable concrete. The utilization of the combination of
fly ash and air entrainment is observed to enhance the freeze-thaw durability of the
concrete for as long as the carbon content of the fly ash is with a 6% limit (Russell et al.
2006).
34
3 EXPERIMENTAL SET-UP
Four different sets of experiments were conducted in order to characterize the overall
performance of the SDA concrete. Varying amounts of SDA were used as a replacement
of cement (binder) in the concrete mixes used to manufacture test specimens. Several
design mixes were prepared and tested for their compressive strength, each tested at 3, 7,
14, 28 and 56 days. Mixes were also prepared and tested in accordance to the appropriate
ASTM standards in order to determine bond strength (A944), corrosion (G109) and
durability/ freeze-thaw (C666) properties of the concrete.
3.1 Materials
3.1.1 Spray Dryer Ash
The SDA used in this research was obtained in Northern Colorado at the Rawhide Power
Station, managed by the Platte River Power Authority. The specific gravity of the SDA
used was 2.71 g/cc. This SDA had a significant amount of lime at 23.65 percent and a
sulfur trioxide content of 6.19 percent, which exceeds the ASTM C618 limits for Class C
fly ashes for use in concrete, as shown in Table 3.1. The increased lime (in addition to the
lime content in the Class C fly ash) and sulfur contents are contributed by the scrubber
process.
35
Table 3.1: Partial Chemical Composition of the Spray Dryer Ash (SDA) Used6
SiO2 Al2O3 Fe2O3 CaO SO3 LOI
SDA Composition (%) 39.76 14.31 5.56 23.45 6.19 1.65
ASTM requirement for
Class C (%)
Total >50 - <5.0 <6.0
3.1.2 Other materials
Type I/II cement conforming to ASTM C150 “Standard Specification for Portland
Cement” was used for manufacture of test specimens. The aggregates used met ASTM
C33 “Standard Specifications for Concrete Aggregates.” Well-graded, normal weight
aggregates were used as coarse aggregates and natural sand for fine aggregates. The
material specifications are indicated in Table 3.2:
Table 3.2: Concrete Material Specifications
Constituent Material Description Specific
Gravity
Moisture
Content
(%)
Bulk
Unit
Wt
Fineness
Modulus
Cement Type I/II (ASTM C150) 3.15 NA NA NA
Coarse Aggregate Well-graded, 3/4" max. size 2.68 2.00 - NA
Fine Aggregate Natural sand (ASTM C33) 2.64 1.00 - 2.80
‘Micro-Air’ air entraining admixture (a BASF product) was used to make specimens for
freeze-thaw testing and conforms to the specifications of ASTM C260 “Standard
Specification for Air Entraining Admixtures for Concrete.” The admixture is an aqueous
solution of alkyl aryl sulfonate which was added to the water used for concrete mixing.
6 SGS North America, Inc
36
3.2 Mix Design
The PCA Absolute Volume method (Komastka et al. 2002, Appendix A, Table 3.3) was
used to design the concrete mixes, with the constituent materials previously described
(Table 3.2). The absolute volume method computes the absolute volumes of the
constituent concrete materials using the parameters given in Tables 3.2 and 3.3 and later
converts the volumes to weights (Tables 3.4 and 3.5) through the use of the individual
specific gravities.
The mix design was based on a Class S35, a dense high strength structural concrete that
is specified by CDOT for higher strength concrete and is normally utilized for bridge
deck construction (CDOT, 2008). The concrete mixes were standardized against the
Class S35 standard concrete mix design for a strength of 4500psi (31MPa). In order to
ensure that the desired strength of 4500psi is met, the PCA method bases the actual
design on the target (required mean) strength which accounts for any irregularities or
flaws that may occur in the concrete preparation process.
37
Table 3.3: Summary of the PCA Absolute Volume Method for 1 yd3(27 ft3)
Non-Air entrained
concrete
Air entrained
Concrete Units
Desired compressive strength 4500 4500 psi
Target compressive strength 5700 5700 psi
Water/cementitious ratio 0.525 0.440 -
Air content 2 5 %
Slump desired 1 1 in
Water content 5.45 4.90 ft3
Cementitious content 3.30 3.53 ft3
Coarse aggregate content 10.03 10.03 ft3
Fine aggregate content 7.70 7.20 ft3
The mixes used for the compressive and bond strength tests were non-air entrained while
the durability (freeze-thaw) and corrosion test mixes were air entrained. The details for
the mixes used for the different types of tests are shown within the test descriptions.
3.3 Compressive Strength Test
The concrete for the compressive strength tests was designed using the PCA Absolute
Volume Method for a design strength of 4500 psi (31MPa) with a target strength (at 28
days) of 5700psi (39MPa) and a slump ranging between 1" – 3" (25 – 75 mm) hence a
water/cementitious ratio of 0.525 was used. The concrete mixes were made using Type
I/II cement that conforms to ASTM C150 and without the use of any water reducers.
38
They were prepared and batched by weight with varying percentages of SDA added to
replace varying percentages of the cement and fine aggregates, as shown in Table 3.4.
Table 3.4: Non –Air Entrained Concrete Mixes; Design Strength 4500psi /31MPa
Parameter Control Mix 1 Mix 2 Mix 3 Mix 4 Mix 5 Mix 6 Mix 7 Mix 8
SDA (%) 0 15 20 25 30 35 40 45 50
Water (lb) 324 324 324 324 323 323 323 323 323
Cement (lb) 648 550 518 486 453 421 389 356 324
SDA (lb) 0 97 130 162 194 227 259 291 324
Coarse agg (lb) 1707 1707 1707 1707 1707 1707 1707 1707 1707
Fine agg (lb) 1279 1265 1261 1256 1252 1248 1243 1239 1234
The concrete was prepared according to ASTM C192 “Standard Practice for Making and
Curing Concrete Test Specimens in the Laboratory.” Both metal and plastic cylindrical
molds were used to cast cylinders and a small concrete mixer was used to manufacture
the concrete. Three cylinders were manufactured for each point required to be tested. The
concrete samples were moist cured at a 99% humidity level and each cylinder specimen
was tested to failure using a compression tester (Fig. 3.2) with a loading rate of
approximately 30.4 psi/sec (212 KPa/sec) after 3, 7, 14, 28 and 56 days of curing. The
results of the three cylinder tests were averaged for each point and tabulated. Results are
discussed in Chapter 4.
39
Fig.3.1: Compression Testing Machine
3.4 Bond Strength Test
Bond strength tests were conducted at the Engineering Research Center, in accordance to
ASTM A944 – 05 “Standard Test Method for Comparing Bond Strength of Steel
Reinforcing Bars to Concrete using Beam-end Specimens”. The test aims to determine
the bond strength of concrete specimens containing variable amounts of SDA.
Concrete beams of 24" x 9" x 17" (610mm x 229mm x 432mm) were cast in wooden
forms as shown in the schematic in Fig. 3.2. A No.4 (No.13) steel reinforcement bar was
used as the main bar for the bond/anchorage strength testing. The rest of the bars used
played a passive role in the test, but facilitated moving the specimens around the lab. The
main rebar was placed from one end of the specimen to the halfway point of the
specimen, where it was linked to a ½ in (12.5 mm) diameter hollow steel conduit by a
polyvinyl chloride (PVC) bond breaker, as shown in Fig.3.2. The conduit allowed for
access for displacement measurement.
40
Fig.3.2: Beam/ Rebar Specimen set-up
Design mixes similar to the compressive strength test were used for the bond test. The
concrete (Table 4) was prepared by machine mixing and was cast and compacted into the
molds in three layers, using a tamping rod. A total of nine specimens were made with
three of each containing 0%, 25% and 50% SDA replacement. The specimens were moist
cured at 99% humidity in a curing room for at least 28 days.
Fig.3.3: Schematic of Test Apparatus (ASTM A944-05)
41
The schematic of the test configuration provided in the ASTM standard is shown in Fig.
3.3. Fig. 3.4 shows pictures of the actual laboratory implementation of this test. Each
specimen was positioned against the yoke linked to the actuators (Fig. 3.4). The rebar at
one end of the beam was gripped by the wedge grip attached to the yoke and a
compression member was placed against the bottom edge of the beam. The beam was
held down on the opposite end by a tie down C- section so as to prevent rotation of the
beam specimen while the rebar was being pulled out.
Fig.3.4: Schematic of Beam- End Specimen and Apparatus
The test method was conducted by pulling the No. 4 rebar from the concrete beam at a
constant loading rate of 0.05 - 0.1in/min, until failure. The variation of the bond strength
(force) with the displacement of the rebar was measured at the actuator by a software
program whose results correlate with the bond force present at the concrete-rebar
interface. Dial gages were also attached at either end of the rebar to measure the relative
displacement of the rebar as it was being pulled out of the concrete. The dial gage
readings were recorded manually at 10 second intervals, in synchronization with the
actuator readings.
yoke
Wedge grip
actuator
Beam specimen
Dial gage
Tie-down C-section
42
Concrete cylindrical samples were also cast and tested for 28 day compressive strength to
determine the strength of the concrete in the bond strength specimens. The results
attained from the actuator’s software, dial gages and Compression Testing machine were
recorded and results will be analyzed in the successive chapter.
3.5 Durability (Freeze-Thaw) Test
This test’s aim is to determine the relative dynamic modulus of elasticity and durability
factor of the SDA concrete specimens when subjected to repeated cycles of freezing and
thawing. The modulus and the durability factor are a measure of the concrete’s
deterioration and it they are a function of its fundamental transverse frequency.
Due to the repeated cycles of freezing and thawing, concrete utilized for this purpose is
usually air entrained. The Control concrete used in the freeze-thaw testing was designed
for a similar design strength of 4500psi (31MPa) at 28days, but with a 5% air content.
Mixes for the concrete specimens containing SDA were designed in reference to the
Control concrete mix, so as to allow for a comparison of the effect of cement replacement
by SDA. In order to maintain a consistent design strength with the standard concrete
utilized in the other tests, concrete containing air entraining admixture had its
water/cementitious material ratio adjusted to 0.44. The mix designs are shown in Table
3.5.
43
Table 3.5: Air-Entrained Concrete Mixes (Design Strength 4500psi (31MPa))
Parameter Control Mix 1 Mix 2
SDA (%) 0 25 50
Water (lb) 305 305 305
SDA (lb) 0 173 347
Cement (lb) 693 520 347
Coarse aggregate (lb) 1708 1708 1708
Fine aggregate (lb) 1279 1256 1234
Air entrainer content(fl.oz) 19 35 52
Trial mixes were conducted to determine the dosage of air entrainment required to
provide the desired 5% air content in each of the 0%, 25% and 50% SDA concrete mixes.
Varying amounts of air entrainer were added to each trial mix; a sample of the concrete
was taken from each trial and was tested for the air content using the volumetric method
(ASTM C173) and air indicator kit (AASHTO T196) as a confirmatory test. These
methods involved the addition of isopropyl alcohol atop a sample mortar paste placed in
the testing bowl (volumetair) as shown in Fig. 3.5.
Fig.3.5: Air Entrainment Testing apparatus
44
The test apparatus was inclined at 45o, rolled across a flat surface and shaken until all the
air in the mortar paste was completely displaced by the isopropyl alcohol. The amount of
air displaced was recorded as the air content of the concrete sample. This test procedure
was repeated several times until an air content of 5% was obtained. The amount of air
entrainer that provided the 5% air content was noted as the sufficient amount. Generally
more air-entrainer was required with increasing SDA quantities. The amount of air
entrainer used ranged between 6 – 17 fl. oz (177 – 503 ml) per 100 lbs (45 kg) of
cementitious material.
Durability testing of the mixes was conducted in accordance with ASTM C666-97
“Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing.”
Three concrete prisms (Fig. 3.6) of 16" x 3" x 4" (406mm x 76mm x 102mm) were
prepared for each of the mixes containing 0%, 25% and 50% SDA. The specimens were
soaked in water contained in stainless steel containers with internal dimensions of 16.25"
x 3.25" x 4.50" (413mm x 83mm x 114mm), and subjected to repeated cycles of freezing
and thawing in a refrigerator. The freezing and thawing cycle involved alternating the
temperature of the specimen from 40 oF to 0oF (4.4 – 17.8oC) within 4 hours, with half
the time given to freezing and thawing respectively.
45
Fig.3.6: Concrete Prisms for Freeze-thaw testing
After each set of 35 cycles, the specimens were weighed and tested for the fundamental
transverse frequency (ASTM 215) using an accelerometer linked between the specimen
and a frequency analyzer as shown in Fig. 3.7 and 3.8.
Fig.3.7: Schematic of Apparatus for Transverse Frequency Test
Fig.3.8: Apparatus for Frequency Testing
Specimen
Accelerometer/ Amplifier Frequency Analyzer
(LabView Program)
46
The specimen being tested was placed on soft rubber supports and an accelerometer was
attached onto the top edge of the specimen. An impact hammer, designed to the standard
specifications (ASTM C215), was used to strike the center of the specimen to induce
vibrations within the specimen. The vibrations were picked up and measured by the
accelerometer and recorded using a frequency analyzer, which is a program written using
LabView software (Fig. 3.9). The program recorded at least 5000 points of the frequency
waveform per iteration and the peak frequency was recorded as the transverse frequency
of the concrete specimen. Several iterations/ strikes were made and results averaged for
each specimen.
Fig.3.9: LabView Program
The results were tabulated and used to determine the relative dynamic modulus of
elasticity and the durability factor. The relative dynamic modulus of elasticity (RDM)
was determined through its relationship to the concrete specimens’ transverse frequencies
47
(nc) at varying numbers of cycles (c) against its initial transverse frequency (n), as given
by equation 3.1.
./0 12
3
13 x 100 (3.1)
While the durability factor (3.2) was determined through its relationship with the RDM,
number of cycles at which RDM reaches the specified minimum value for discontinuing
the test (N) or the specified number of cycles at which the exposure is to be terminated
(whichever is less) and the specified number of cycles at which the exposure is to be
terminated (M).
/6 789:
9 (3.2)
The test, conducted in accordance to ASTM C 666, was terminated after 300 cycles of
repeated freezing and thawing exposures since none of the specimen’s RDM dropped
below 60% of its initial modulus.
3.6 Corrosion Test
The aim of this test was to investigate the corrosion inhibition or acceleration properties
of concrete with SDA used as a binding agent and to evaluate its effect on the corrosion
of steel in concrete. The specimens were prepared and cast in reference to ASTM G109
“Standard Test Method for Determining the Effects of Chemical Admixtures on the
corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride
Environments.”
The rebar required for the testing was prepared by power brushing to near white, and then
later soaked in hexane to clean them. They were allowed to dry. One end of the rebar was
48
drilled and tapped to make provision of contact screws and nuts. Both ends of the rebar
were taped with electroplater tape and with neoprene tubing, exposing 8 in (203 mm)
within the middle portion. The ends of the tubing were filled with 2-part epoxy. The rebar
specimens were then placed in the timber forms as shown in Fig. 3.10 with each
specimen containing two bars placed at the bottom and one positioned at the top.
Fig.3.10: Timber forms and rebar for corrosion specimens
Air-entrained concrete, designed to meet 4500 psi (31MPa) strength at 28 days (Table
3.5) was prepared and cast in the timber forms. The concrete specimens were later moist
cured for at least 28 days. On removal from the curing room, the specimens were allowed
to dry before 3" x 6" x 3" (76mm x 152mm x 76mm) plastic (Acrylic) dams were glued
with silicone caulk onto the top surface. Epoxy was later applied to the concrete on all
four sides and top surface outside the dam (Fig.3.11b).
Fig.3.11: a) Corrosion Specimens b) with Plastic dams and Epoxy
49
The specimens were then supported on half inch non-conducting supports, soaked in a
3% sodium chloride (salt) solution at a depth of ½ inch and stored at 50% humidity. The
plastic dams were also half filled with 3% Sodium Chloride (NaCl) solution.
The specimens were soaked for 14 days in the NaCl solution, after which they were
removed and allowed to dry for another 14 days. At the end of the drying period the total
potential (TC) and voltage (V) across the 100-Ω resistor (between the top and bottom
rebars) was measured and used to compute the macrocell current (i) which is given by
equation (3.3) below:
; <
=>> (3.3)
The total corrosion (corrosion potential) of the rebars was measured against a Silver
Nitrate (AgNO3) reference electrode (ASTM C876) placed in the plastic dam on top of
each specimen were measured. The corrosion potential (TC) is measured in Coulombs
and is given by equation (3.4) below:
?@A ?@AB= & CDA E DAB= F ;A & ;AB=/2H (3.4)
The specimens were then re-subjected to the same cycle of soaking and drying for a total
of 5 months.
50
4 RESULTS AND ANALYSIS
4.1 Compressive Strength
Test cylinders whose cement quantities were partially replaced with SDA varying from
0 - 50% were cast and tested until failure as shown in Fig. 4.1. The ultimate compressive
strength of the test specimen at failure was noted, and raw results from each test are given
in Appendix B. The results indicated in the following sub-sections are the average results
for compressive strength of three-specimen samples.
Fig. 4.1: Concrete Test Specimens at Failure
4.1.1 Early Strength Gain (0 – 7days)
From the results shown in Fig. 4.2 it is apparent that the presence of SDA clearly
decelerates the early strength gain (within the first 3 – 7 days). This is probably due to the
slow activity of the pozzolanic reaction occurring during the curing process. All mixes
with SDA had a lower 3 day strength than the Control mix. As the amount of SDA
increased the difference in strength between the SDA mixes and the Control mix also
increased. Approximately a 10% reduction in the strength was observed for samples with
small amounts of SDA replacement, within the first 3 days. Larger reductions of about
50% were observed for th
Fig. 4.2:
Within the next 4 days, an increase in the concrete strength in excess of the 5084 psi
(35MPa) achieved by the
between 20 – 35%. Beyond 35% cement replacement by SDA, the strength gained at 7
days of curing is much lower than the
4.1.2 Rate of Strength Gain
Concrete with SDA exhibits an initial low strength development (within the first 7 days)
but later has its strength
strength gain is observed
when increasing quantities of SDA are added to the concrete as
(Control) concrete (Fig. 4.3). The trends in the results indicate that all specimens
about 70 – 80% of their 28 day
3,997 3,814
4,518
0
1000
2000
3000
4000
5000
6000
15%
Com
pres
sive
str
engt
h (p
si)
51
small amounts of SDA replacement, within the first 3 days. Larger reductions of about
50% were observed for the larger SDA contents.
Fig. 4.2: Early Compressive Strength of SDA Concrete
Within the next 4 days, an increase in the concrete strength in excess of the 5084 psi
(35MPa) achieved by the Control mix was observed for specimens with SDA varying
35%. Beyond 35% cement replacement by SDA, the strength gained at 7
days of curing is much lower than the Control.
Rate of Strength Gain
Concrete with SDA exhibits an initial low strength development (within the first 7 days)
strength gain accelerate steadily. Generally, an in
strength gain is observed at later stages in the curing process (beyond 7 days of curing)
when increasing quantities of SDA are added to the concrete as
e (Fig. 4.3). The trends in the results indicate that all specimens
their 28 day strength within the first 7 days of curing.
3,814 3,690 3,802 3,737
2,4991,933
5,175 5,270 5,341 5,270
4,492
20% 25% 30% 35% 40% 45%SDA (%) in concrete
Day 3
small amounts of SDA replacement, within the first 3 days. Larger reductions of about
SDA Concrete
Within the next 4 days, an increase in the concrete strength in excess of the 5084 psi
mix was observed for specimens with SDA varying
35%. Beyond 35% cement replacement by SDA, the strength gained at 7
Concrete with SDA exhibits an initial low strength development (within the first 7 days)
steadily. Generally, an increase in the rate of
at later stages in the curing process (beyond 7 days of curing)
when increasing quantities of SDA are added to the concrete as compared to standard
e (Fig. 4.3). The trends in the results indicate that all specimens attained
strength within the first 7 days of curing. Beyond the 7
1,933 1,857
4,4614,209
3,896
5,084
45% 50% Control
Day 3 Day 7
days, specimens containing SDA had their strength increase steadily until
the target strength of 5700psi (39MPa) at 28 days. At 56 days of curing, all specimens
with SDA varying between 20
specimen by about 2 -16%.
Fig. 4.3:
4.1.3 Ultimate Strength
The ultimate compressive strength of concrete is usually assessed by its 28
though with fly ash mixes, a 56
the results for the 28-day and 56
It can be observed that the results of the entire set of specimens were within range of the
Control specimens at both 28 and 56 days of curing. Specimens with SDA of 15% and
50% had a lower 28-day strength gain than the
1500
2500
3500
4500
5500
6500
7500
3
Com
pres
sive
Str
engt
h (p
si)
52
days, specimens containing SDA had their strength increase steadily until
target strength of 5700psi (39MPa) at 28 days. At 56 days of curing, all specimens
with SDA varying between 20 – 50% had a strength exceeding that of the
16%.
Fig. 4.3: Compressive Strength against Age of Concrete
Strength
The ultimate compressive strength of concrete is usually assessed by its 28
though with fly ash mixes, a 56-day strength has also been considered. Fig.
day and 56-day strength in comparison to the Control concrete mix.
It can be observed that the results of the entire set of specimens were within range of the
at both 28 and 56 days of curing. Specimens with SDA of 15% and
day strength gain than the Control mix, though the magnitude of the
3 7 14 28 56Age of Concrete (days)
days, specimens containing SDA had their strength increase steadily until they exceeded
target strength of 5700psi (39MPa) at 28 days. At 56 days of curing, all specimens
50% had a strength exceeding that of the Control
Compressive Strength against Age of Concrete
The ultimate compressive strength of concrete is usually assessed by its 28-day strength,
day strength has also been considered. Fig. 4.4 illustrates
the Control concrete mix.
It can be observed that the results of the entire set of specimens were within range of the
at both 28 and 56 days of curing. Specimens with SDA of 15% and
ix, though the magnitude of the
56
20% SDA
30% SDA
40% SDA
50% SDA
Control
difference is not significant in comparison to the target design strength of 5700 psi. The
rest of the specimens, containing
day target strength and generally that of the Co
Fig. 4.4: Compressive Strength against SDA Concrete (for 28 and 56 days)
At 56 days of curing all specimens in excess of 20% SDA had their strength exceeding
the 6458 psi (45MPa) attained by the Control concrete. From the graph (Fig. 4.
be deduced that utilizing SDA would provide some long
comparison to the Control (standard) concrete. The SDA provides a
benefit on ultimate strength gain of concrete at 28 days and approximately
days.
The trends in Fig. 4.4 show that
the most favorable results for compressive strength
to indicate a reduction in the strength as more SDA is added to the concrete
5,650
6,5146,225
0
1000
2000
3000
4000
5000
6000
7000
8000
15% 20%
Com
pres
sive
Str
engt
h (p
si)
53
difference is not significant in comparison to the target design strength of 5700 psi. The
rest of the specimens, containing 20 – 45% SDA did have their strength exceed the 28
day target strength and generally that of the Control specimens.
Compressive Strength against SDA Concrete (for 28 and 56 days)
At 56 days of curing all specimens in excess of 20% SDA had their strength exceeding
the 6458 psi (45MPa) attained by the Control concrete. From the graph (Fig. 4.
be deduced that utilizing SDA would provide some long-term strength benefits in
comparison to the Control (standard) concrete. The SDA provides a
on ultimate strength gain of concrete at 28 days and approximately
The trends in Fig. 4.4 show that concrete with SDA ranging between
results for compressive strength. Beyond 35% SDA, the trends seem
to indicate a reduction in the strength as more SDA is added to the concrete
6,5146,154
6,808 6,366 6,130 5,977
7,132 7,050 7,262 7,5166,891 6,602
20% 25% 30% 35% 40% 45%SDA content in concrete (%)
difference is not significant in comparison to the target design strength of 5700 psi. The
45% SDA did have their strength exceed the 28-
Compressive Strength against SDA Concrete (for 28 and 56 days)
At 56 days of curing all specimens in excess of 20% SDA had their strength exceeding
the 6458 psi (45MPa) attained by the Control concrete. From the graph (Fig. 4.4) it can
term strength benefits in
comparison to the Control (standard) concrete. The SDA provides a 4 – 18% added
on ultimate strength gain of concrete at 28 days and approximately 6 – 15 % at 56
ranging between 25 – 35% provided
Beyond 35% SDA, the trends seem
to indicate a reduction in the strength as more SDA is added to the concrete. It is probable
5,9775,541 5,765
6,602 6,8616,458
45% 50% Control
Day 28
54
that at some point beyond 50% replacement, SDA would cease to provide added benefit
when utilized in concrete.
The results also verify that the range of variable mixes chosen for the compressive
strength test with 10 – 50% SDA were viable, hence for the next three sets of tests a
reduced range was chosen for testing. Due to the time constraints for the research, only
three different concrete mixes were considered for experimental investigation. The
chosen sample points for the rest of the tests were specimens with 0% (Control), 25% and
50% of their Portland cement content replaced by SDA. The points selected were chosen
to range about the recommended limits (ASTM C618) of 20 - 35% fly ash utilized in
replacement of cement in concrete.
4.2 Concrete Shear Bond
This section presents the results for the pull–out (bond) test (ASTM A944) that was
carried out to investigate the concrete-steel bond behavior in concrete specimens
containing 25% and 50% SDA. The bond specimens were cast from non-air entrained
concrete in wooden forms. At the same time cylinders for compressive strength tests were
prepared to confirm the strength of the concrete used in the bond specimens. Both tests
were conducted after a minimum of 28 days (at 35 days) of moist curing.
The results in the following sub-sections will address the compressive and bond strength
of concrete specimens containing 0%, 25% and 50% SDA. The physical behavior and
mode of failure of the beam specimens will be discussed in the first section. The next
sections will quantitatively examine the bond behavior of the specimens in terms of the
displacements and strengths recorded during testing. The last section will present the
55
results of the compressive strength tests and discuss their relationship to the bond
strength.
4.2.1 Mode of Failure
The beam specimens were loaded monotonically under a pull – out test (ASTM A944)
and two types of failure mechanisms were observed. These included longitudinal cracks
and pull out of the steel rebar. Longitudinal cracks of similar patterns of were physically
observed among most of the test specimens, with the exception of two of the specimens,
as reflected in Table 4.1.
One of the beam specimens with 50% SDA (B7) did not exhibit any physical failure
mode despite the increase in load. This could be attributed to the ductile behavior that
was uniquely exhibited in this beam (Fig. 4.7). The other beam (B2) that did not display a
failure mode simply did not exhibit cracks on the surface despite reaching its peak load,
based on the load at failure this beam appears to have failed prematurely.
Fig. 4.5: Beam loaded indicating Shear Bond failure
The cracks began to form gradually at the front of the specimen and continued to
propagate up to the approximate midpoint on the top face of the specimen as the
maximum load was approached (Fig. 4.5). Upon failure, the initial crack widened and
56
terminated in an inverted T, hence permitting for the complete pull-out of the rebar. At
this point, the behavior of the bond-slip response was non-existent.
4.2.2 Load-Slip Response
A total of nine beams were prepared for the pull-out test and tested after 35 days of moist
curing. The tests on the beams were carried out over several days and were subjected to
variable loading rates. Three different loading rates (0.050, 0.075 and 0.100 in/min) were
used in the test. An initial loading rate of 0.050 in/min was used on the first specimen
tested. The loading rate was later increased to 0.075in/min and 0.100 in/min for the rest
of the specimens as illustrated in Table 4.1, since the first specimen took over 30 minutes
to fail. The variable rates affected the duration at which the peak results were attained.
57
Table 4.1: Summary of Bond Test Results
SDA
(%)
Beam
Number
Loading
Rate
(in/min)
Peak Load
(kips)
Peak
Slip (in)
Description of Failure
0%
B1 0.075 17.870 0.095* Longitudinal crack-¼way center
B2 0.075 8.049 0.035 No visible crack
B3 0.05 16.969 0.035 Longitudinal crack-¼way center
25%
B4 0.075 19.486 0.452 Longitudinal crack-½way center
B5 0.075 19.511 0.418 Longitudinal crack-½way center
B6 0.10 12.538 0.089 Longitudinal crack-¼way center
50%
B7 0.10 (20.906)** (0.500)** No visible crack
B8 0.10 17.471 0.183 Longitudinal crack-½ center
B9 0.10 19.288 0.137 Mild crack formed at center edge
*value noted does not correlate to peak load (excluded from discussion)
**no peak values – specimen results simply plateaued out (last highest value is noted)
BX – values excluded from discussion.
The results of loads against the displacements (slip) of a No. 4 (0.5”) reinforcing steel bar
are discussed in the following sections. Various displacement measurements were
recorded: one by the actuator and two by the dial gages at both closed and open ends of
the specimen apparatus. The load results were obtained from the actuator measurements
while the (actual) slip results used for analysis were obtained by computing the difference
between the dial gage readings at the closed and open end of the specimens. The
computed slip results denote the actual slip of the rebar. The actuator recorded redundant
58
slip readings hence they could not be used to denote the actual slip, but only the peak
loads. The curves generally exhibit a similar polynomial trend; the curves peak to a
maximum, and then later takes on a descent as expected. Beyond the peak value, there is no
more concrete-steel bond relationship and any increase in load simply pulls out the steel bar.
4.2.2.1 Specimens with 0% SDA
Fig. 4.6 shows the load-displacement response of the individual specimens with 0% SDA
that were tested as Control specimens. The computer (actuator) measurements and dial
gage readings at the closed end convey similar patterns in the load-slip behavior (Fig.
4.6). The variation of the dial gage readings can be attributed to the strain occurring in the
steel during pull out. Details of the strain discussion will be addressed in section 4.2.4.
The dial gage readings of 4.6 (a) and (c) do not correlate well with the computer
(actuator) readings due to poor synchronization of the manual and computer
measurements. Therefore the actual bond-slip behavior will be assumed to compare
parallel to total slip (blue curve) and an approximation of the maximum slip of 0.6 and
0.4 inches respectively is made.
Beam specimen B2 (Fig 4.6(b)) exhibited an expected trend but peaked at a much lower
value than the other specimens of similar mix design. An error in the consolidation of the
concrete is presumed to be the source of the poor bonding of concrete with the rebar.
Hence the beam (B2) will be eliminated from the subsequent discussion of results.
59
Fig. 4.6(a): Load vs. Slip for beam (B1) Fig. 4.6(b): Load vs. Slip for beam (B2)
Fig. 4.6( c): Load vs. Slip for beam (B3)
4.2.2.2 Specimens with 25% SDA
Fig. 4.7 illustrates the load-slip results (load results from actuator against actual slip
results obtained by computing the difference between the dial gage readings at the closed
and open end) for the individual specimens with 25% SDA, measured by the actuator and
dial gages. Beams B4 and B5 exhibited very similar behavior and both peaked at about
20 kips. Beam specimen B6 peaked at a much lower value and this was due to slackness
of the embedded steel bar in the concrete. The consolidation of this specimen was
0.0
4.0
8.0
12.0
16.0
20.0
0.0 0.2 0.4 0.6 0.8
Load
(ki
ps)
Slip (in)
0.0
4.0
8.0
12.0
16.0
20.0
0.0 0.2 0.4 0.6 0.8
Load
(ki
ps)
Slip (in)
actuator open end
closed end actual
0.0
4.0
8.0
12.0
16.0
20.0
0.0 0.2 0.4 0.6 0.8
Slip
(ki
ps)
Slip (in)
60
inadequate; hence inadequate concrete bond was actualized around the rebar. Therefore
beam B6 will be omitted from the discussion of the results and only beams B4 and B5
will be considered for analysis.
Fig. 4.7: Load vs. Slip for beams (B4, B5, B6) with 25% SDA
4.2.2.3 Specimens with 50% SDA
The beams prepared with 50% SDA exhibited very similar behavior in all three
specimens with the exception noted with the peak/ plateau behavior (Fig. 4.8). Beam B7
exhibited an expected trend of an increase in slip with an increment in load except that it
failed to peak. The beam simply plateaued displaying very ductile behavior. The
variations of the peak (plateau) values for the beams ranged between 17 – 21 kips.
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
0.0 0.1 0.2 0.3 0.4 0.5 0.6
Load
(ki
ps)
Slip (in)
B4
B5
B6
61
Fig. 4.8: Load vs. Slip for beams (B7, B8, B9) with 50% SDA
4.2.3 Bond Strength
The Control concrete specimens portrayed the lowest bond strength in this experiment.
Their average peak strength was the lowest at 17.420 kips while the specimens with 25%
SDA portrayed the highest average peak value of 19.499 as illustrated in Table 4.2. In
comparison to the Control the specimen with 25% SDA exhibited the better bond-slip
response.
Specimens with 50% SDA did exhibit a higher peak value than the Control, though the
trend of results indicates a decrease in the peak load (bond strength) with an increase in
the SDA content. However, it is uncertain to tell from the results, at what SDA content
that the peak values would start to drop below that of the Control specimen. The outcome
is as expected when compared with the compressive strength results in section 4.2.5,
since the bond strength is directly proportional to the compressive strength of concrete.
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
16.0
18.0
20.0
22.0
0.0 0.1 0.2 0.3 0.4 0.5 0.6
Load
(ki
ps)
Slip (in)
B7
B8
B9
62
Table 4.2: Average Results of Peak Loads (kips), Peak Slips (in) and Rebar Strains
SDA (%) Peak Load (kips) Peak Slip (in) Rebar Strain
0% 17.420 0.500* 0.0417
25% 19.499 0.435 0.0363
50% 18.380 0.160 0.0134
* approximated from curve comparison
Deducing from the results, the utilization of SDA in concrete can be seen to increase the
shear bond behavior of the concrete. Overall, SDA offered better bond strengths than the
Control specimen though the variations of 12% (25% SDA) and 5% (50% SDA) are
relatively small. From the result of observation and comparison between the bond
strengths, the best results are attained when SDA is utilized in concrete within limits not
exceeding 25% replacement.
4.2.4 Peak Slip and Strain
From Fig. 4.6, 4.7 and 4.8 the peak slips of the beam specimens are observed and the
average values are presented in Table 4.2 above. Results of the average maximum strains
are computed from the peak slips over the 12 inch embedded length of the steel bar and
are presented in the same table. The strains computed are a direct correlation to the steel
rebar’s yield strain since the difference in the dial gages measurements recorded the
elongation in the rebar.
Addition of SDA in concrete reduced the slip between the rebar and concrete. The trend
of results also indicates a decrease in the slip length and strain with an increase in the
63
SDA. This could be as a result of an increased frictional resistance that the SDA offers
the concrete.
4.2.5 Compressive Strength of Bond Test Specimens
In determining the bond behavior, a standard compressive strength test (ASTM C192)
was performed to determine the actual compressive strength used and investigate its
influence on the bond behavior. A standard compressive strength test (ASTM C192) was
performed alongside the bond test specimens, on three-sample cylinders per point to
determine the actual compressive strength used. The average concrete strengths shown in
Table 4.3 indicate that the specimen met the target design strength requirement of
5700psi.
Table 4.3: 28- day mean Compressive Strengths (psi) for the Bond test specimen
SDA content (%) 0% 25% 50%
C. Strength (psi) 5777 6726 5665
Expected B. Strength (psi) 924 1034 973
Actual B. Strength (psi) 912 984 903
The expected bond strength (bond stress) is calculated from the compression-bond
relationship illustrated in equation 2.1. Comparison of the measured bond strength/
stresses with the expected results indicates a closeness in the range of results, with a
greatest variation seen with the specimen with 25% SDA. The closeness in results
indicates that the compression-bond strength relationship is still applicable even with
SDA concrete. Examining the directly proportionality (compression-bond relationship) in
64
the results illustrated in Table 4.3, the compression strength test can be observed to
confirm the effect that it has on the bond strength of concrete.
4.3 Concrete Durability (Freeze-thaw)
Alternate cycles of freezing and thawing subject concrete to durability concerns, which
include mainly two types of deterioration, namely surface scaling and internal cracking.
Scaling (loss of small particles of mortar on a concrete surface) is the most frequently
observed form of deterioration. However, this research will particularly consider the
second form of deterioration, cracking that is caused by the internal pressures generated
by the action of frost within the hardened concrete. Among the various factors affecting
the resistance of the concrete to frost is the strength of the aggregate-mortar interface, and
the pore structure of the mortar (Pigeon et al. 1995). In this research we utilize ASTM
C666 to study the effect that SDA has on these factors that determine the freeze-thaw
properties of concrete. The method in the standard requires the measurement of the
fundamental frequency (and relative dynamic modulus of elasticity) and calculation of
the durability factor, whose respective reduction and value are indicators of the extent of
internal cracking in concrete specimens (Pigeon et al. 1995).
The air entrained mixes utilized for the durability test were moist cured and the test
procedure (including freeze-thaw cycling) started at 28 days after curing. They were
subjected to 300 cycles of freezing and thawing as specified in ASTM C666 and
periodically tested according to ASTM C215. Each cycle involved 2 hours for the
freezing and thawing respectively, for a total of 4 hours. The following sub-sections will
present the average results of three-specimen samples of the freeze-thaw durability test
65
and discuss the variations caused by the freeze-thaw cycles in weight change, relative
dynamic modulus of elasticity and the durability factor.
4.3.1 Weight Change
The change in weight (or mass) can be an indicator of deterioration of concrete
specimens in instances where surface scaling is observed. As shown in Table 4.4, the
results of the present research show negligible variations in the specimen weights,
indicating no occurrence of surface scaling. This outcome aligns with the assumptions on
which this test (ASTM C666) was designed to be conducted. The assumptions are based
on the fact that internal cracking would be the only expected form of deterioration
experienced by air entrained concrete specimens.
66
Table 4.4: Average %age Weight change of specimens over N cycles
Average %age Weight change
N ∆0% ∆25% ∆50%
0 0.00 0.00 0.00
35 0.33 0.43 0.42
70 -0.05 0.00 0.00
105 -0.06 0.08 0.03
140 0.03 -0.05 -0.02
175 -0.04 -0.01 0.02
210 0.03 -0.01 -0.04
245 0.03 0.03 0.04
280 -0.02 -0.01 0.04
300 0.01 0.01 -0.02
(Total ∆= ) 0.26 0.46 0.48
Minor variations are observed within the specimens. The SDA specimens exhibited
greater mass changes than the Control (0% SDA) specimen by about 0.20%. The minor
variations in weight gain can likely be attributed to the ingress of water within the
internal cracks and a weight loss can relate to minor abrasion of the concrete.
4.3.2 Freeze-thaw Resistance
The primary measures of deterioration are the relative dynamic modulus of elasticity
(RDM) and the durability factor (DF) and they are calculated from the measurements of
the fundamental transverse frequency (ASTM C666). A reduction in fundamental
67
frequency, hence a reduction in the RDM, signifies internal disruptions/ deteriorations
within the concrete due to the alternate cycles of freezing and thawing.
All specimens utilized for this test were air entrained and contained an air content of
approximately 5%. Increasing amounts of air entraining admixture were utilized for every
increase in SDA content, so as to achieve a similar 5% air content. The results (Fig. 4.9,
Table 4.5) of these parameters (RDM and DF) are deduced from the measurements of at
least three hammer strike point records of the transverse frequencies (ASTM C215) of
air-entrained concrete specimens recorded after every 35 cycles of freezing and thawing
until the test reached 300 cycles.
Fig. 4.9 shows a general decrease in the RDM with an increase in the number of freeze-
thaw cycles, signifying a decrease in the freeze-thaw resistance of the concrete over time.
The trend indicates a close relationship between the samples with 25% and 50% SDA,
but in comparison with the Control specimen the concrete specimen with 50% SDA
provided a slightly higher freeze-thaw resistance after 300 cycles. Overall the SDA
appears to slightly reduce the freeze-thaw resistance of the concrete.
68
Fig 4.9: Change in RDM (%) of SDA Concrete vs. Number of Cycles
Table 4.5 shows the computed durability factors which exceed 85% of contrasted
threshold (Wang, 2009) furthermore the relative durability factors exceed the 80%
threshold defined by ASTM C260. The concrete specimens can all be defined to possess
excellent resistance to freeze-thaw, based on the RDF limits of ASTM C260.
Table 4.5: Durability Factors and Relative Durability Factors
SDA (%) in concrete Durability Factor, % Relative Durability Factor (RDF),%
0% 90.940 (ref)
25% 88.057 96.8%
50% 89.045 97.9%
The variation between the SDA concrete specimens is rather insignificant and it is
therefore difficult to determine or recommend the most favorable SDA content for use in
concrete. Hence comparison is made between concrete with and without SDA, which
86.00
88.00
90.00
92.00
94.00
96.00
98.00
100.00
102.00
0 35 70 105 140 175 210 245 280 315
RD
M (
%)
Number of Freeze-thaw Cycles, N
0% 25% 50%
0% SDA DF = 90.9
25% SDA DF = 88.1
50% SDA DF= 89.0
69
indicates that utilizing SDA in concrete would provide a slight decrease the freeze-thaw
resistance of the concrete when designed at the same air content.
4.4 Concrete Corrosion
An important part of this research was to evaluate the corrosion performance of the rebar
embedded in the SDA concrete and to determine whether the SDA inhibits or accelerates
the corrosion activity of steel in concrete. This evaluation was conducted in accordance to
ASTM G109, which calls for measuring the half cell (corrosion) potential and the voltage
drop across the 100-Ω resistor placed across the bottom (cathode) and top rebars (anode),
whose results aid in determining the total integrated macrocell current and the steel’s
total corrosion. Potential measurements are generally used to determine corrosion of steel
embedded in concrete and also provide a semi-quantitative indication regarding corrosion
in the Sodium Chloride (NaCl) corrosive medium. The total corrosion (metal loss) is a
measure of the thickness of the bar lost to corrosion and a direct indicator of the extent of
chloride ion penetration through the concrete while the total macrocell integrated current
is a measure of the rate of corrosion activity due to the macrocell. This section will
discuss the results of the potential and current measurements and use them to analyze the
effect that SDA has on the corrosion property of concrete.
Beam specimens prepared as described in Chapter 3 were moist cured for 28 days, and
later were subjected to 14 days of soaking in 3% Sodium Chloride (NaCl) solution
followed by 14 days of drying. The NaCl solution provided a necessary ion path in the
corrosion reaction of the specimen. The tests were carried out through 5 soak-dry cycles
and electrical potentials were measured across a 100-Ω resistor after each cycle between
70
the top and bottom steel bars and against a Silver Nitrate (AgNO3) half cell reference
electrode (ASTM C876) using a voltmeter. At the end of the testing the specimens were
broken open to visual inspection to determine the extent of corrosion activity of the
embedded steel.
4.4.1 Chloride Ion Penetration (Total Corrosion)
The penetration of chloride ions is a function of the permeability of concrete and a
measure of the total corrosion experienced by the steel. The water-cementitious ratio is
the major factor that governs the permeability of concrete. Among other factors that play
a significant role in determining the permeability of the concrete is the cement/material
specification. Therefore this section will discuss the effect that SDA would likely have on
the permeability of concrete and thus damage of structures subjected to chloride
environments. A corrosion test (ASTM G109) was carried out to investigate this property
and presented below (Table 4.6) are the average results of three sample reinforced
concrete beam specimens carried out over 5 months for each point containing 0%, 25%
and 50% SDA in concrete.
71
Table 4.6: Average Corrosion Potentials (against Reference Electrode)
SDA Content (%) 0% 25% 50%
Time (days) Half cell (Corrosion) Potential (mV)
0 0.00 0.00 0.00
28 -256.82 -276.11 -272.30
56 -183.90 -195.99 -219.91
84 -161.42 -163.68 -145.90
112 -144.47 -202.30 -150.50
140 -135.33 -232.37 -167.07
The results (Table 4.6) indicate that the steel bar embedded in the Control specimen has
decreasing negative potentials over the whole testing period whereas the specimens with
SDA have decreasing negative potentials for the first 84 days of soaking but later show
potentials that have increased slightly. The large negative values indicate corrosion is
beginning to occur (transition state) while the smaller negatives (less than -200mV)
indicate no occurrence of corrosion.
Despite initially high values for the half-cell potentials (ranging between -200 and -350
mV for individual specimens), when compared against the values in Table 4.7 the
measured potentials generally indicate only a 10% probability of the formation of
corrosion cells on the reinforcing steel (ASTM C876). For the given short period of
testing the results indicate that corrosion activity has not yet initiated and the concrete
specimens can be said to be in a passive state. More testing such as measuring the
chloride content (ASTM C1152) and chloride diffusion (ASTM C1556) would be
72
recommended to assist in determining the effect that SDA may have on the corrosion of
embedded steel in concrete.
Table 4.7: Probability of Corrosion (ASTM C876)
E (mVref) Probability of corrosion Corrosion state
More positive than -200mV 10% Passive corrosion
Range -200 to -350 mV uncertain transition
More negative than -350mV 90% Active corrosion
In spite of the absence of active corrosion activity, Fig. 4.10 illustrates the variations of
the resistance of chloride ions (total corrosion) with time. The specimens experienced
moderate to high ion penetrability with the specimen containing 25% SDA exhibiting the
least resistance (largest chloride ion penetration) to the chlorides. The specimen with
50% SDA exhibited the highest resistance to chloride penetration in comparison to the
Control specimen, hence offering the best performance for corrosion resistance.
Fig 4.10: Total Corrosion vs. Concrete age
0
1000
2000
3000
4000
5000
6000
0 28 56 84 112 140 168
Tot
al C
orro
sion
, TC
j( C
)
Concrete age (days)
0%
50%
25%
73
From the figure (Fig. 4.10) large (50%) SDA contents can be observed to increase the
chloride inhibition properties of concrete. This is as expected, that an increased SDA
content would inadvertently decrease the resistance of the concrete to chloride
penetration. This is because the fineness of fly ash (and SDA) has been seen to provide
added benefit to the impermeability property of concrete (Crouch et al. 2009).
4.4.2 Rate of Corrosion activity
This sub-section addresses results of the measurements of the macrocell corrosion current
between the top and bottom steel bars embedded in concrete and investigates the rate of
corrosion of the steel bars over time. The corrosion rate (how fast or slow corrosion was
occurring over time) depends on the amount of current flowing through the macrocell
(specimen with corroding (anode) and cathodic members) and gives a quantitative
indication of the corrosion tendency of the test specimen (Fig.4.11).
Fig. 4.11: Macrocell Current vs. Time of testing (Corrosion rate)
0
500
1000
1500
2000
2500
3000
0 28 56 84 112 140 168 196
Cor
rosi
on c
urre
nt (
µA
)
Time of Testing (days)
0%
25%
50%
74
The results of the specimens with 25% SDA illustrate an initial steep increase in the slope
of curve (corrosion rate) for the first 3 months indicating a high rate of corrosion activity.
The rate of corrosion activity after the 3 months is seen to drop significantly. The Control
specimen presents a fluctuating and a relatively steady rate of corrosion activity.
The results also show a steady and low increase in the macrocell current for the concrete
specimen with 50% SDA, indicating that the replacement of 50% SDA in concrete would
provide a relatively low corrosion rate. This would be expected given that SDA is a much
finer material than cement, hence would provide a low chloride permeable material that
would inhibit the rate of corrosion.
75
5 RECOMMENDATIONS AND CONCLUSIONS
5.1 Conclusions
This thesis investigated the potential for valuable utilization of SDA and its performance
in structural concrete. Experimental work was carried out to determine the effect that
SDA had on the compressive and bond strength of concrete, its freeze-thaw durability
and its corrosion inhibition properties on steel rebar embedded in concrete. Mixes with
varying amounts of SDA were designed and tested in the accordance to the appropriate
ASTM standards.
In general, the addition of SDA provided modest benefits when used in certain
proportions and at the very least it did not seem to degrade the properties much. It
provided reasonable benefits on the compressive and bond strength when utilized within
the optimal limits. Despite the need for more air entrainer, utilization of SDA produced a
negligible effect on the freeze-thaw durability of the concrete while an increase in the
SDA provided an increased corrosion resistance and a reduced corrosion rate in concrete.
Based on the results of this research, SDA has great potential for its utilization as a
structural material in transportation infrastructures. The following conclusions can be
drawn from the results of this research:
5.1.1 Compressive Strength
Replacement of cement in concrete by SDA generally increases the ultimate strength of
the concrete. Generally, the strength attained at 28 and 56 days by concretes containing
SDA superseded the strength attained by the Control (standard) concrete, indicating an
76
added benefit of about 4 – 18% and 6 – 15% respectively on ultimate strength gain of
concrete.
The results of this study do not indicate at which point the continued replacement of
cement with SDA would cause the compressive strength to decline below the strength
observed from the Control (standard) concrete.
A 25 - 35 % SDA replacement provides the best strength results of about 400 – 650psi in
excess of the target strength at 28 days and about 1350 – 1800psi at 56 days. Beyond 35
% SDA replacement, the ultimate compressive strength decreases but mixes with higher
replacement percentages are still able to reach the desired design strength.
Replacement of cement with SDA reduces the rate of early strength development/ gain.
Generally, concrete with SDA exhibits an initial low strength development for the first 3
days but has its strength accelerate steadily after that time.
5.1.2 Bond Strength
The addition of SDA to concrete provides an increase in bond strength of concrete, in
comparison to the Control specimen, although the variations of 12% (for 25% SDA) and 5%
(for 50% SDA) are relatively small. However from the trend it is uncertain at what SDA
percentage that the bond strength will drop below that of the Control specimen.
The most optimal results in the bond strength are attained when SDA utilized in concrete
is limited to 25% replacement. Doubling this quantity of SDA (50%) resulted in reduced
77
variations (decreased bond strength in comparison to the Control). Utilization of SDA
provides a worse bond-slip behavior than plain concrete with an increase in the SDA content.
The compression-bond relationship was a direct proportionality (equation 2.1) and the
compressive strength test results confirmed its effect on the bond strength of concrete. The
test also confirmed that the relationship (equation 2.1) was still applicable to SDA concrete.
5.1.3 Freeze-thaw (Durability)
More air entraining admixture is required for increasing amounts of SDA replacement in
order to achieve the same air content in concrete. The dosages required in SDA concrete do
exceed those used in plain concrete by more than half.
Minor variations in the weight changes of the specimen had negligible effect on the
results on the freeze-thaw testing.
The relative dynamic modulus of elasticity (RDM) of concrete generally decreases with
an increase in the freeze-thaw cycles indicating a decrease in the freeze-thaw resistance
of the concrete over time.
Concrete specimens with 50% SDA provided a slightly higher freeze-thaw resistance
than the specimens with 25% SDA, when compared to the Control although the
variations between the SDA concrete specimens are relatively small. It is therefore
difficult to determine or recommend the most favorable SDA content for use in concrete.
Hence comparison is made between concrete with and without SDA, which otherwise,
indicates that SDA in concrete offers a lower freeze-thaw resistance than the Control
concrete.
78
Utilizing SDA in concrete provides a slight decrease in the durability factor indicating a
negligible effect on the freeze-thaw resistance (durability) of the concrete when designed
at the same air content.
5.1.4 Corrosion
For the given short period of testing the results indicated a 10% probability of corrosion
(formation of corrosion cells on the reinforcing steel). Active corrosion has not yet been
instigated and the concrete specimens are considered to be in a passive state.
In spite of the absence of active corrosion activity, the specimen with 50% SDA offered
the best performance for corrosion resistance. It exhibited the highest resistance to
chloride penetration in comparison to the Control specimen, while the specimen
containing 25% SDA exhibited the least resistance (largest chloride ion penetration) to
the chlorides. The corrosion resistance of concrete increases with an increase in SDA.
The specimen with 50% SDA provides the least corrosion rate (low increase in the
macrocell current) as would be expected given that SDA is a much finer material than
cement. Drawing from the previous conclusion a good corrosion resistant (a low chloride
permeable) material would inhibit the rate of corrosion.
79
5.2 Recommendations
In utilizing SDA, the concrete industry does continue to recognize the importance of
sustainable development and the potential benefits that this material has to offer. This
research provides an introduction to a clearer understanding of the behavior and
performance of this SDA material when used in concrete and the recommendations
outlined below are proposed to complement this work.
Given the potential for the valuable use of Spray Dryer Ash (SDA) and fly ash in general,
its beneficial properties, and the likely increase in its production, it is paramount that
further research be carried out to better understand the variable aspects and properties of
this material.
Before this material can be routinely used, additional research should be carried out to
investigate other essential properties of the material such as the dry density, stiffness,
flexural strength, toughness, abrasion resistance, sulfate resistance and other long term
durability concerns. Other environmental performance and field handling characteristics
need to be further investigated and quality Control measures designed to ensure its
standard application. After considering its structural performance and characteristics in
totality, a design standard would be appropriate and useful for future use.
The tests carried out in this research would require further in-depth study to determine the
trends and behavior of the material when more variable points are considered. In
particular the corrosion test would require a longer duration to clearly establish the
corrosion inhibition properties of the concrete. It is also recommended that more study be
80
carried out to determine the behavior of concrete when larger quantities of SDA
replacements, in excess of 50% are used.
It is also recommended that a more detailed understanding of the SDA material be carried
out to critically understand the physical, chemical and mineralogical properties of the
material and its variations in properties due to the variable processing methodologies
utilized at the various coal plants. Additional studies on the use of supplemental chemical
activation materials such as lime and alkali compounds could also be useful in improving
the performance of the material.
This research focused more on the positive utility of the SDA in general and very little
concern was given to the high sulfur content. The effect of the high sulfur content should
be further investigated and its role in hardened concrete and non-structural applications
should also be determined.
81
6 REFERENCES
AASHTO (1994) AASHTO LRFD Bridge Design Specifications Washington, D.C: American Association of State Highway and Transportation Officials
AASHTO T196 (2009). Air Content of Freshly Mixed Concrete by the Volumetric Method
ACI 211.1-91. (1991). Standard Practice for Selecting Proportions for Normal, Height weight and Mass Concrete. ACI Manual of Concrete Practice, Part 1. Detroit, Michigan: American Concrete Institute.
ACI 211.4R-93. (1996). Guide for Selecting Properties for High-Strength Concrete with Portland Cement and Fly Ash. ACI Manual of Concrete Practice, Part 1. Detroit, Michigan: American Concrete Institute.
ACI Committee 318. (2008)) Building Code requirement for Structural Concrete ACI Standard 318-08. Detroit, Michigan: American Concrete Institute.
American Chemical Society (ACS). (2009). The Foul Side of 'Clean’ Coal. Chemical & Engineering News, 23 February 2009 Publication, accessed online at http://pubs.acs.org/cen/sustainability/sustainability.html (Oct 15, 2009)
American Coal Ash Association (ACAA). (2010). CCP Production and Use Statistics accessed at http://www.acaa-usa.org/displaycommon.cfm?an=1&subarticlenbr=3 (Feb 09, 2010)
American Coal Ash Association (ACAA). (2007). CCP Production and Use Survey Data accessed online at http://www.epa.gov/waste/partnerships/c2p2/use/index.htm (Nov 02, 2009)
American Coal Ash Association (ACAA). (2009) Facts About Coal Ash, accessed online at www.coalashfacts.org (Nov 02,2009)
ASTM Standard A944. (2005). Standard Test Method for Comparing Bond Strength of Steel Reinforcing Bars to Concrete using Beam-End Specimen,” West Conshohocken, Pennsylvania: ASTM International.
ASTM Standard C125. (2009). Standard Terminology relating to Concrete and Concrete Aggregate, West Conshohocken, Pennsylvania: ASTM International
ASTM Standard C150. (2009). Standard Specification for Portland Cement, West Conshohocken, Pennsylvania: ASTM International
82
ASTM Standard C173. (2009). Standard test method for air content of freshly mixed concrete, volumetric method. West Conshohocken, Pennsylvania: ASTM International.
ASTM Standard C192. (2006). Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory, West Conshohocken, Pennsylvania: ASTM International.
ASTM Standard C618 (2008a) Standard Specification for Fly Ash, Calcined Natural Pozzolan for Use as Mineral Admixture in Portland Cement Concrete, West Conshohocken, Pennsylvania: ASTM International.
ASTM Standard C618. (2008a). Standard Specification for Fly Ash and Raw or Calcined Natural Pozzolan for Use as Mineral Admixture in Concrete, West Conshohocken, Pennsylvania: ASTM International.
ASTM Standard C666. (2003). Standard Test Method for Resistance of Concrete to rapid Freezing and Thawing. West Conshohocken, Pennsylvania: ASTM International.
ASTM Standard C876. (2009). Standard Test Method for Corrosion Potentials of Uncoated Reinforcing Steel in Concrete. West Conshohocken, Pennsylvania: ASTM International.
ASTM Standard G109. (1999a). Standard Test Method for Determining the effects of Chemical Admixtures on the Corrosion of Embedded Steel Reinforcement in Concrete Exposed to Chloride Environments. West Conshohocken, Pennsylvania: ASTM International.
Babcock and Wilcox. (1978). Steam: Its Generation and Use. New York: New York Appendices
Bavarian B. and Reiner L. (2006) Current Progress in Corrosion Inhibition of Reinforcing Steel in Concrete using Migrating Corrosion Inhibitors San Diego, California: California State University
Berry M., Cross D., and Stephens J. (2009). Changing the Environment: An alternative ‘green’ concrete produced without Portland cement. Lexington, Kentucky: 2009 World of Coal Ash Conference, May 4-7, 2009.
Buck A. D. (1977) Recycled Concrete as a source of Aggregate. ACI Journal Proceedings, 74 (5) p212-219
83
Burden D. (2006). The Durability of Concrete containing high levels of fly ash. University of New Brunswick
Bye G.C. (1999). Portland Cement. London, UK: Thomas Telford Publishing
Chang E. H. (January 2009) Shear and Bond behavior of Fly-Ash based geo-polymer Concrete Beams, Cirtin University of Technology.
Cross, D., J. Stephens, and J. Vollmer. (2005). Structural Applications of 100 Percent Fly Ash Concrete. Lexington, Kentucky: 2005 World of Coal Ash Conference, April 11-15, 2005
Crouch L.K. and Philips Jason. (2009). Lean, Green and Mean Concrete Lexington, Kentucky: 2009 World of Coal Ash Conference, May 4-7, 2009
CDOT. (2008). Concrete Table: Standard Specifications for Road and Bridge Construction Colorado Department of Transportation, Colorado
Daigle L. and Lounis Z. (2006). Life Cycle Cost Analysis of High Performance Concrete Bridges considering their environmental impacts. Ottawa Canada: Institute for Research in Construction, National Research Council.
Eligehausen R., Bertero V., and Popov E. (1983).Local Bond Stress-Slip Relationships of Deformed Bars Under Generalized Excitations. Earthquake Engineering Research Center, Report no. 83-23, University of California, Berkeley, CA.
Elsageer M. A., Milliard S. G. and Barnett S. J. (2009). Strength Development of Concrete containing coal fly ash under different curing conditions. Lexington, Kentucky: 2009 World of Coal Ash Conference, May 4-7, 2009
EPRI. (2007). A Review of Literature Related to the Use of Spray Dryer Absorber Material; Production, Characterization, Utilization Applications, Barriers, and Recommendations. Electric Power Research Institute, TR1014915, September 2007.
EPRI (1998). Coal Ash: Its origin, Disposal, Use and Potential Health issues. Environmental Focus, Issue Report Electric Power Research Institute, BR-111026.
Garshol F.K., Lacerda L. (2007) Shotcrete Corner: Watertight Permanent Shotcrete Linings in Tunneling and Underground Construction American Shotcrete Association, Fall 2007 Shotcrete Publication
84
Golden D. M and DiGioia A. M. (2003). Fly Ash for Highway Construction and Development, USEPA Case Study No.10.
Hoffman G. K. Western Region Fly Ash Survey. Socorro, New Mexico: New Mexico Bureau of Mines and Mineral Resources
King B. (2005). Making Better Concrete: Guidelines to using Fly Ash for Higher Quality, Eco-friendly Structures. California: Green Building Press
Kosmatka S.H, Kerkhoff B. and Panarese W.C. (2002). Design and Control of Concrete Mixtures. Portland Cement Association
Kumar Binod, Tike J. K and Nanda P. K. (2007). Evaluation of properties of High Volume Fly Ash for Concrete pavements ASCE Journals of Materials Vol. 19, No. 10, pp. 906-911
Lowes, L.N., Moehle, J.P., and Govindjee, S. (2004) Concrete-Steel Bond Model for Use in Finite Element Modeling of Reinforced Concrete Structures, ACI Structural Journal, July-August 2004.
Maggenti Ric (2009) Green Mass Concrete for San Fransisco Bay HPC Bridge Reviews, Issue 57, Sept. /Oct. 2009; California Department of Transportation, CA
Malhotra V.M. (1986) Fly Ash, Silica Fume, Slag and Natural Pozzolans in Concrete, Madrid, Spain: Proceedings-Second International Conference
National Bridge Inventory, 1994
Nawy G. E Reinforced Concrete: A Fundamental Approach, 4th edition, New Jersey: Prentice Hall, Inc
Neville A. (2006) Concrete, London, UK: Thomas Telford
PCA (2002) Types and Causes of Concrete Deterioration, Concrete Technology, CIS536, Portland Cement Association, Skokie, Illinois
PCA. (2006). A History of Cement Portland Cement Association, Skokie, Illinois
PCA. (2009). Building Green with Concrete Portland Cement Association, accessed online at http://www.cement.org/buildings/green_leed (Nov 12, 2009)
85
PCA. (2009a). Highways Portland Cement Association, accessed online at http://www.cement.org/pavements/pv_cp_highways.asp (Nov 10, 2009)
PCA. (2009b). Highways Portland Cement Association, accessed online at http://www.cement.org/buildings/ (Nov 10, 2009)
Pigeon M. and Pleau R (1995). Durability of Concrete in Cold Climates. London, UK: E & FN Spon
Poutos K.H., Alani A.M., Walden P.J., Sangha C.M.. (2008) Relative temperature changes within concrete made with recycled glass aggregate. Construction and Building Materials, Volume 22, Issue 4.
Ramesh C. Joshi, Rajinder P. Lohtia. (1997). Fly Ash in Concrete: Production, Properties and Uses. London, UK: Taylor & Francis Group
Richardson G. M. (2002) Fundamentals of Durable Reinforced Concrete New York: New York Spon Press
Russell L. H, Borax Technologies and Folliard K. (Fall 2006) The Impact of Fly Ash on Air entrained concrete Tech Talk: University of Texas
Sharp R.S. (2004) Evaluation of two corrosion Inhibitors using two application methods for Reinforced Concrete structures Charlotteville, Virginia: Virginia Transportation Research Council
Smith, P. (Summer 2006) Fly Ash: A nuisance dust worth its weight in cement Concrete News
Tempest .B. et al.(May 2009). Optimization of Fly Ash based Geopolymer Concrete by measurement of free hydroxyl ions Lexington, Kentucky: 2009 World of Coal Ash Conference, May 4-7, 2009
TRB. (2009). Concrete Bridges Transportation Research Board A2C03 Committee on Concrete Bridges http://onlinepubs.trb.org/onlinepubs/millennium/00019.pdf, Accessed on Dec 10, 2009
Trejo D, Folliard K. J. and Lianxiang D (2004). Sustainable Development using Controlled Low-Strength material Texas, USA
86
US Geological Survey (2008), Mineral Commodities Summary: Cement. In van Oss H.G comps., available online at http://minerals.usgs.gov/minerals/pubs/commodity/cement/mcs-2008-cemen.pdf (Nov 12, 2009)
USGS (Oct 2008). 2006 Minerals Yearbook. United States Geological Survey
Wang K (2009) Freeze-thaw Durability of Low Permeability Concrete Ames, Iowa: Institute for Transportation, Iowa State University
Wipf J. T (2006) Evaluation of Corrosion resistance of the different steel reinforcement types Ames, Iowa: Bridge Engineering Center, Iowa State University.
87
APPENDIX A: MIX DESIGN
(PCA Absolute Volume Method (Komastka et al. 2002) for a cubic yard)
Constituent
Material
Description Specific Gravity
Moisture Content
(%)
Bulk Unit
Wt (pcf)
Fineness Modulus
Cement Type I, ASTM C150 3.15 NA NA NA
Coarse Aggregate Well-graded, 3/4" max. size 2.68 2.00
NA
Fine Aggregate Natural sand (ASTM C33) 2.64 1.00
2.80
Density of water = 62.4 pcf
Desired compressive strength = 4500 psi
Required mean compressive strength = 5700 psi (reference Table 9-11)
Water/cement ratio = 0.525 (interpolated from Table 9-3, note maximum from Table 9-1)
Air content = 2 % (entrapped air based on Table 9-5; we will not use air-entrainment)
Slump desired = 1 in (based on Table 9-6)
Water content = 340 lb (for a cubic yard of concrete, based on Table 9-5)
Cement content = 648 lb (water content)/(w/c ratio)
Coarse aggregate content = 1674 lb (based on Table 9-4),(unit weight in pcf) *(27ft3/yd3) * (bulk volume)
Admixture content = 0 fl oz
Determining fine aggregate content by volume:
Water = 5.45 ft3 (content in lbs)/(specific gravity x density of water)
Cement = 3.29 ft3 (content in lbs)/(specific gravity x density of water)
88
Air = 0.54 ft3 (percent/100 x 27 ft3)
Coarse aggregate = 10.03 ft3 (content in lbs)/(specific gravity x density of water)
Total - fine aggregate = 19.31 ft3
Fine aggregate = 7.69 ft3 [27 - (Total - fine aggregate)]
Fine-aggregate content = 1267 lb (volume x specific gravity x density of water)
Corrections for moisture content of aggregates:
Coarse aggregate = 1707 lb (weight x (1 + MC/100))
Fine aggregate = 1280 lb (weight x (1 + MC/100))
Water = 16.25 lb (weight of water) - (CA dry weight x MC/100) - (FA dry weight x MC/100)
(reference page 164)
Final weights for one cubic yard of concrete:
Water = 324 lb
Cement = 648 lb
Coarse aggregate = 1707 lb
Fine aggregate = 1280 lb
Final weights for indicated cubic feet of concrete:
Cubic feet of concrete desired = 0.2 ft3
Water = 2.4 lb
Cement = 4.8 lb
Coarse aggregate = 12.65 lb
Fine aggregate = 9.5 lb
89
APPENDIX B: COMPRESSIVE STRENGTH RESULTS
Day 3 Day 7 Day 14 Day 28 Day 56
Mix
type
Load
(kips)
Strength
(psi)
Mean
strength
(psi)
Load
(kips)
Strength
(psi)
Mean
strength
(psi)
Load
(kips)
Strength
(psi)
Mean
strength
(psi)
Load
(kips)
Strength
(psi)
Mean
strength
(psi)
Load
(kips)
Strength
(psi)
Mean
strength
(psi)
Control
(C )
123,000 4,350
4,461
150,000 5,305
5,084
157,500 5,570
5,623
171,000 6,048
5,765
184,500 6,525
6,428 120,750 4,271 138,750 4,907 160,500 5,677 156,000 5,517 180,750 6,393
134,625 4,761 142,500 5,040 159,000 5,623 162,000 5,730 180,000 6,366
Mix 1
(15%)
102,750 3,634
3,997
153,750 5,438
4,518
152,250 5,385
5,243
168,750 5,968
5,650
168,000 5,942
6,225 120,750 4,271 129,000 4,562 157,500 5,570 151,500 5,358 175,500 6,207
115,500 4,085 100,500 3,554 135,000 4,775 159,000 5,623 184,500 6,525
Mix 2
(20%)
112,500 3,979
3,814
148,000 5,234
5,175
165,000 5,836
6,166
182,000 6,437
6,514
210,000 7,427
7,132 105,000 3,714 145,000 5,128 178,000 6,295 185,000 6,543 200,000 7,074
106,000 3,749 146,000 5,164 180,000 6,366 185,500 6,561 195,000 6,897
Mix 3
(25%)
102,500 3,625
3,690
145,000 5,128
5,270
172,500 6,101
5,865
175,000 6,189
6,154
197,500 6,985
7,050 103,000 3,643 147,000 5,199 160,000 5,659 176,000 6,225 200,500 7,091
107,500 3,802 155,000 5,482 165,000 5,836 171,000 6,048 200,000 7,074
Mix 4
(30%)
105,000 3,714
3,802
153,000 5,411
5,341
158,000 5,588
5,647
190,500 6,738
6,808
210,000 7,427
7,262 110,000 3,890 147,000 5,199 161,000 5,694 195,000 6,897 198,000 7,003
107,500 3,802 153,000 5,411 160,000 5,659 192,000 6,791 208,000 7,356
90
Mix 5 (35%)
110,000 3,890
3,737
156,000 5,517
5,270
147,500 5,217
5,535
180,000 6,366
6,366
210,000 7,427
7,516 107,000 3,784 141,000 4,987 160,500 5,677 180,000 6,366 217,500 7,692
100,000 3,537 150,000 5,305 161,500 5,712 180,000 6,366 210,000 7,427
Mix 6 (40%)
70,000 2,476
2,499
120,000 4,244
4,492
152,500 5,394
5,199
175,000 6,189
6,130
196,000 6,932
6,891 70,000 2,476 131,000 4,633 148,500 5,252 182,500 6,455 187,500 6,631
72,000 2,546 130,000 4,598 140,000 4,951 162,500 5,747 201,000 7,109
Mix 7 (45%)
50,000 1,768
1,933
120,000 4,244
4,209
141,000 4,987
5,111
165,000 5,836
5,977
185,000 6,543
6,602 53,000 1,874 118,000 4,173 145,000 5,128 175,000 6,189 185,000 6,543
61,000 2,157 119,000 4,209 147,500 5,217 167,000 5,906 190,000 6,720
Mix 8 (50%)
50,000 1,768
1,857
115,000 4,067
3,896
135,000 4,775
4,769
161,000 5,694
5,541
198,000 7,003
6,861 61,500 2,175 105,500 3,731 135,000 4,775 146,000 5,164 180,000 6,366
46,000 1,627 110,000 3,890 134,500 4,757 163,000 5,765 204,000 7,215
91
APPENDIX C: BOND STRENGTH RESULTS
C-1: COMPRESSIVE STRENGTH RESULTS
SDA Content 0% 25% 50%
Load (lbs) Strength (psi) Load (lbs) Strength (psi) Load (lbs) Strength (psi)
Specimen 1 169,000 5,977 189,000 6,684 159,000 5,623
Specimen 2 159,000 5,623 190,000 6,720 157,500 5,570
Specimen 3 162,000 5,729 191,500 6,773 164,000 5,800
Average Load 163,333 5,777 190,167 6,726 160,167 5,665
92
APPENDIX D: FREEZE-THAW RESULTS
D-1: WEIGHTS OF SPECIMENS
Specimen weights (lbs)
Number of cycles F1 F2 F3 F4 F5 F6 F7 F8 F9
0 17.0945 17.2690 17.2575 16.8165 17.3315 17.0905 16.6440 16.5680 16.5145
35 17.1830 17.2790 17.3290 16.8950 17.3990 17.1640 16.6655 16.6600 16.6120
70 17.1890 17.2585 17.3200 16.8880 17.4005 17.1670 16.6920 16.6535 16.5905
105 17.1735 17.2605 17.6050 16.9320 17.4020 17.1625 16.6895 16.6660 16.5945
140 17.1765 17.2620 17.3135 16.8975 17.4020 17.1705 16.6760 16.6705 16.5935
175 17.1700 17.2453 17.3135 16.9030 17.3945 17.1675 16.6790 16.6755 16.5960
210 17.1730 17.2490 17.3200 16.8975 17.3940 17.1680 16.6655 16.6725 16.5930
245 17.1850 17.2530 17.3210 16.9040 17.4005 17.1730 16.6725 16.6780 16.6005
280 17.1885 17.2490 17.3125 16.9103 17.4060 17.1547 16.6741 16.6773 16.6196
300 17.1805 17.2550 17.3175 16.9003 17.4045 17.1662 16.6755 16.6785 16.6080
93
D-2: TRANSVERSE FREQUENCY SPECIMEN RESULTS No. of cycles, N 0 35 70 105 140 175 210 245 280 300
Frequencies, n n n1 n2 n3 n4 n5 n6 n7 n8 n9
Specimen Transverse Frequencies (Hz) of Specimen
F1 2113.827 2082.046 2073.580 2069.592 2077.249 2076.594 2067.357 2044.235 2027.128 2020.531
F2 2108.627 2098.052 2077.139 2074.838 2088.375 2084.751 2061.373 2040.126 2022.174 2010.982
F3 2109.156 2081.596 2061.436 2043.567 2064.042 2060.241 2052.496 2038.934 2018.548 2006.463
F4 2081.460 2047.932 2023.852 2026.220 2023.238 2019.809 2005.575 1988.983 1960.385 1948.248
F5 2093.413 2062.223 2034.641 2029.213 2034.141 2035.677 2024.236 1999.234 1971.732 1962.532
F6 2096.846 2062.817 2047.701 2043.845 2044.014 2041.672 2029.800 2001.278 1983.457 1974.531
F7 1993.339 1947.169 1939.403 1947.342 1960.468 1953.203 1937.064 1919.934 1908.345 1897.564
F8 2063.989 2033.577 2006.201 2005.815 2010.305 2013.207 2002.835 1958.358 1939.002 1931.345
F9 2004.587 1967.230 1938.517 1938.527 1948.033 1951.721 1934.348 1915.458 1902.463 1890.623
Average Transverse Frequencies (Hz) of Specimen
0% 2110.537 2087.231 2070.718 2062.666 2076.555 2073.862 2060.409 2041.098 2022.617 2012.659
25% 2090.573 2057.657 2035.398 2033.093 2033.798 2032.386 2019.870 1996.498 1971.858 1961.770
50% 2020.638 1982.659 1961.374 1963.895 1972.935 1972.710 1958.082 1931.250 1916.603 1906.511
94
D-3: RELATIVE DYNAMIC MODULI OF ELASTICITY (RDM) SPECIME N RESULTS N 0 35 70 105 140 175 210 245 280 300
RDM Pn0 Pn1 Pn2 Pn3 Pn4 Pn5 Pn6 Pn7 Pn8 Pc9 DF
Specimen Values of Relative Dynamic Modulii of Elasticity (%)
F1 100.000 97.016 96.228 95.858 96.569 96.508 95.652 93.524 91.965 91.368 91.368
F2 100.000 98.999 97.036 96.821 98.088 97.748 95.568 93.608 91.968 90.953 90.953
F3 100.000 97.404 95.526 93.877 95.768 95.415 94.699 93.452 91.593 90.499 90.499
F4 100.000 96.804 94.541 94.763 94.484 94.164 92.841 91.312 88.705 87.610 87.610
F5 100.000 97.042 94.464 93.961 94.417 94.560 93.500 91.205 88.713 87.887 87.887
F6 100.000 96.781 95.367 95.009 95.024 94.807 93.707 91.092 89.477 88.674 88.674
F7 100.000 95.421 94.662 95.438 96.729 96.014 94.433 92.771 91.654 90.621 90.621
F8 100.000 97.075 94.479 94.442 94.866 95.140 94.162 90.026 88.255 87.560 87.560
F9 100.000 96.308 93.517 93.518 94.437 94.795 93.115 91.305 90.071 88.953 88.953
Average Values of Relative Dynamic Modulii of Elasticity
0% 100.000 97.806 96.263 95.519 96.808 96.557 95.306 93.528 91.842 90.940 90.940
25% 100.000 96.876 94.791 94.577 94.642 94.510 93.350 91.203 88.965 88.057 88.057
50% 100.000 96.268 94.219 94.466 95.344 95.316 93.903 91.367 89.993 89.045 89.045
95
APPENDIX E: CORROSION TEST RESULTS
E-1: SPECIMEN RESULTS AT 28 DAYS
SDA Content Specimen Voltage across
Resistor, V (mV)
Macrocell Current,
I 28 (µA)
Corrosion Potential
(mVref)
Total Corrosion,
TC28 (C)
0%
CF1 167.99 1,679.90 273.50 2,032.01
CF2 140.71 1,407.10 264.44 1,701.97
CF3 178.99 1,789.90 232.53 2,165.06
25%
CF4 176.65 1,766.50 278.14 2,136.76
CF5 125.00 1,250.00 252.26 1,512.00
CF6 137.16 1,371.60 297.94 1,659.03
50%
CF7 161.71 1,617.10 273.65 1,956.04
CF8 107.83 1,078.30 272.75 1,304.25
CF9 115.57 1,155.70 270.51 1,397.93
96
E-2: SPECIMEN RESULTS AT 56 DAYS
SDA Content Specimen Voltage across
Resistor, V (mV)
Macrocell Current,
I 56 (µA)
Corrosion Potential
(mVref)
Total Corrosion,
TC56 (C)
0%
CF1 182.50 1,825.00 209.80 4,239.53
CF2 150.35 1,503.50 170.62 3,520.60
CF3 104.10 1,041.00 171.28 3,424.26
25%
CF4 182.31 1,823.10 172.41 4,341.98
CF5 199.14 1,991.40 193.85 3,920.80
CF6 164.54 1,645.40 221.70 3,649.30
50%
CF7 161.04 1,610.40 240.70 3,903.98
CF8 102.22 1,022.20 208.22 2,540.70
CF9 129.62 1,296.20 210.83 2,965.82
97
E-3: SPECIMEN RESULTS AT 84 DAYS
SDA Content Specimen Voltage across
Resistor, V (mV)
Macrocell Current,
I 84 (µA)
Corrosion Potential
(mVref)
Total Corrosion,
TC84 (C)
0%
CF1 63.70* 1,637.00 154.26 4,187.64
CF2 149.72 1,497.20 126.85 3,629.65
CF3 92.76* 1,927.60 203.16 3,590.82
25%
CF4 261.00 2,610.00 162.10 5,362.28
CF5 288.70 2,887.00 143.45 5,900.91
CF6 179.94 1,799.40 185.49 4,166.83
50%
CF7 180.00 1,800.00 164.57 4,125.22
CF8 131.22 1,312.20 149.87 2,823.69
CF9 113.65 1,136.50 123.28 2,942.59
*Omitted from computation of averages
98
E-4: SPECIMEN RESULTS AT 112 DAYS
SDA Content Specimen Voltage across
Resistor, V (mV)
Macrocell Current,
I 112 (µA)
Corrosion Potential
(mVref)
Total Corrosion,
TC112 (C)
0%
CF1 67.50* 1,675.00 153.00 4,006.20
CF2 146.55 1,465.50 147.10 3,583.68
CF3 110.15 1,101.50 133.30 3,664.00
25%
CF4 162.72 1,627.20 175.60 5,125.32
CF5 196.10 1,961.00 214.40 5,864.14
CF6 196.74 1,967.40 216.90 4,556.32
50%
CF7 76.66* 1,766.60 158.60 4,314.16
CF8 128.50 1,285.00 155.70 3,141.57
CF9 140.35 1,403.50 137.20 3,072.38
*Omitted from computation of averages
99
E-5: SPECIMEN RESULTS AT 140 DAYS
SDA Content Specimen Voltage across
Resistor, V (mV)
Macrocell Current,
I 140 (µA)
Corrosion Potential
against Ref.(mV)
Total Corrosion,
TC140 (C)
0%
CF1 61.30* 1,613.00 112.00 3,977.16
CF2 139.30 1,393.00 131.10 3,457.64
CF3 145.00 1,450.00 162.90 3,086.29
25%
CF4 167.30 1,673.00 213.90 3,991.92
CF5 201.30 2,013.00 246.90 4,806.95
CF6 144.40 1,444.00 236.30 4,126.43
50%
CF7 68.60* 1,686.00 161.10 4,176.26
CF8 158.20 1,582.00 164.80 3,467.92
CF9 132.00 1,320.00 175.30 3,294.35
*Omitted from computation of averages