Post on 27-Oct-2014
transcript
1 1.; II ...•• •
(g. ;'. ;') d .! Ig.:LJ1 "J' ~ :.,_~
International Trading House (S.P.C)
Ref: CORMEC110148jMCSCjSSS Date: 13th October 2011
Email:nilanga68@yahoo.co.uk Mr. Nilanga MCSC Manama, Kingdom of Bahrain
Dear Sir ,
SUB): DESIGN DATA SHEET FOR GRP PIPES (PN 10) (QTN110148) PRO): ALBA CALCINER BYPASS LINE FOR POTABLE WATER PIPELINE
Mahmood AI Burstiaid Chief Executive
i .
0-'~I ' < 1 • • • L...~ I. \\ f, • • : ....... ~. (+'\V"' ) \VV \H"' \ : ~u.(+'\V "' ) \ VV \ · "\ "\ "\ :~
Tel.: (+973) 17710666, Fax : (+973)17712491, P. O. Box : 11400, Manama, Kingdom of Bahrain Website : www.ithonline.com. E-mail : burshaid@batelco.com.bh /burshad1@batelco.com.bh
---
---
---
--
--
--
--
--
--
--
- - -
Cosmoplast Industrial Co... Interplast Co Ltd
PRODUCT INFORMATION & DESIGN DATA FOR GRP PIPES & FITTINGS
Manufacturer details
Name of Manufacturer Cosmoplast Industrial Co. L.L.C
Continuous Dual Helical Filament
Manufacturing Process Wound Process
Product 250mm; PN 10; SN 5,000 N/M-
Document no GRP/250Pl0S05K; Rev 2; 28/09/11
Design reference AWWA Manual M45
Standards Specfication for filament wound fiberglass Pipe ASTM D 2996
Manufacturing process for bends & fittings Mitered
Joint Type PL/PL
PIPE WALL STRUaURE
Nominal Length of Standard Pipe 9.00 M
Total Length of Pipe 9.000 M
Socket Length PL/PL
Spigot Length PL/PL
Rubber Type N/A
Minimum Total Wall Thickness 10.00 mm
Inner Liner :- Thickness (minimum) 1.00 mm
Veil: Glass Type 10% C- Glass
Resin type 90% Isopthalic
CSM : Glass type 45 - 50% E- Glass
resin Type 50 - 65% Isopthalic
Average Glass in Liner 25 - 30 %
Average Resin 65-70 %
Structural Wall :- Thickness (minimum) 8.5
E- Glass (Rovings)
Isopthalic
0.5
C- Glass
Isopthalic
mm
Glass type 70%
Resin type 30%
Outer Liner :- Thickness (minimum) mm
Glass type 10%
Resin type 90% ..
~==- == =_.._-.._.._.._.._.~ -Et2.-~ ·-1-.. r~ 1---.._ ..- __ " _"~_" _' _ .._ .._ .._ ..---1
- ~~ OA/ QC Department \-\~~ Cosmoplast Industrial Co. -
Page 1 of 1
---
---
---
--
--
--
--
--
--
--
Cosmoplast Industrial Co osmoplas
Interplast Co Ltd
PRODUCT INFORMATION & DESIGN DATA FOR GRP PIPES & FlnlNGS
Manufacturer details
Name of Manufacturer Cosmoplast Industrial Co. L.L.C
Continuous Dual Helical Filament
Manufacturing Process Wound Process
Product 400mm; PN 10; SN 5,000 N/M-
Document no GRP/400Pl0S05K; Rev 2; 28/09/11
Design reference AWWA Manual M45
Standards Specfication for filament wound fiberglass Pipe ASTM D 2996
Manufacturing process for bends & fitt ings Mitered
Joint Type PL/PL
PIPE WALL STRUCTURE
Nominal Length of Standard Pipe 12.00 M
Total Length of Pipe 12.000 M
Socket Length PL/PL
Spigot Length PL/PL
Rubber Type N/A
Minimum Total Wall Thickness 10.00 mm
Inner Liner :- Thickness (minimum) 1.00 mm
Veil: GlassType C- Glass
Resin type
10%
90% Isopthalic
CSM : Glass type 45 - 50% E-Glass
resin Type 50 - 65% Isopthalic
Average Glass in Liner 25 - 30 %
Average Resin 65-70 %
Structural Wall :- Thickness (minimum)
70%
8.5
E-Glass (Rovings)
30% Isopthalic
0.5
10% C- Glass
90% Isopthalic
mm
Glass type
Resin type
Outer Liner :- Thickness (minimum) mm
Glasstype
Resin type
F~~ _u=-----== ~=H_- _ :::' ..~ -EF)}} L-- .._ .._ ._ .._ .._.~_. _ .. _ .._ .._ .._ .--1
f!'-'-'~~ . . . .. .. .. -_ . -~
OA/OC Department \:'t:~-~~ ~Cosmoplast Industrial Co.
Page 1 of 1
-- ---
---
---
---
--
--
--
--
--
--
--
Cosmoplast Industrial Co
Interplast Co Ltd I- L ~~ :~·::Z:~~R~;lV ltl G.;rrI\ ~ ~@R'~~_RBlP.JIP.;E:Sf8ttp.lml ~~
Manufacturer details . . -.- -
Name of Manufacturer Cosmoplast Industrial Co. L.L.C
Continuous Dual Helical Filament
Manufacturing Process Wound Process
Product 500mm; PN 10; SI\I 5,000 I\I/Nt
Document no GRP/500P10S05K; Rev 2; 28/09/11
Design reference AWWA Manual M45
Standards Specfication for filament wound fiberglass Pipe ASTM D 2996
Manufacturing process for bends & fittings Mitered
Joint Type PL/PL
PIPE WALL STRUCTURE .. --- --
Nominal Length of Standard Pipe 12.00 M
Total Length of Pipe 12.000 M
Socket Length PL/PL
Spigot Length PL/PL
Rubber Type N/A
Minimum Total Wall Thickness 10.00 mm
Inner Liner :- Thickness (min imum) 1.00 mm
Veil : Glass Type 10% C- Glass
Resin type 90% Isopthalic
CSM : Glass type 45 - 50% E- Glass
resin Type 50 - 65% Isopthalic
Average Glass in Liner 25 - 30 %
Average Resin 65-70 %
Structural Wall :- Thickness (minimum) 8.5 mm
Glass type 70% E- Glass (Ravings)
Resin type 30% Isopthalic
Outer Liner :- Thickness (minimum) 0.5 mm
Glass type 10% C- Glass
Resin type 90% Isopthalic . -
f--====-=- ~ --==- .._-_..._---.--] -C~ ---~- 1- - J~ =- ~.....:.r;-r. = - - ...-.= = . C?""T"""~-==O = -~ -=- ~ ~1- _ ___ __ _ ___ ___ __ _ _ __ ___ ___ ___ __---l
OA/ QC Department ~ - I8Cosmoplast Industrial Co. ""-~
Page 1 of 1
• Cosmoplast Industrial Co osmoplas
Interplast Co Ltd
PRODUCT INFORMATION & DESIGN DATA FOR GRP PIPES & FITIINGS
Manufacturer details
Name of Manufacturer Cosmoplast Industrial Co. L.L.C
Continuous Dual Helical Filament
Manufacturing Process Wound Process
Product 100mm; PN 10; SN 5,000 N/M
Document no GRP/I00PI0S05K; Rev 2; 28/09/11
Design reference AWWA Manual M45
Standards Specfication for filament wound fiberglass Pipe ASTM D 2996
Manufacturing process for bends & fittings Mitered
Joint Type PL/PL
PIPE WALL STRUCTURE
Nom inal Length of Standard Pipe 9.00 M
Total Length of Pipe 9.000 M
Socket Length PL/PL --
Spigot Length PL/PL --
Rubber Type N/A --
Minimum Total Wall Thickness 10.00 mm
Inner Liner :- Thickness (minimum) 1.00 mm
Veil : Glass Type 10% C- Glass --Resin type 90% Isopthalic -CSM : Glass type 45 - 50% E- Glass -resin Type 50 - 65% Isopthalic -Average Glass in Liner 25 - 30 %
Average Resin 65-70 %
Structural Wall :- Thickness (minimum) 8.5 mm
Glass type 70% E- Glass (Rovings) --Resin type 30% Isopthalic -
Outer Liner :- Thickness (minimum) 0.5 mm
Glass type 10% C- Glass
Resin type 90% Isopthalic --
E ----= --- =:- -3 ' -I -=>-} ~tv. .._ -=-==_ H _~'~= p _p ~ ~P : _"_ "_ / L---- .. ._ .._ . _ .._ ..~_ .. .._ .._ .._ .._ ..-----l
~.i~- .. . - . .. ... - .
QA/ QC Department ~~~ Cosmoplast Industrial Co. -=--
Page 10f1
---
---
---
--
--
--
--
--
--
--
Cosmoplast Industrial Co osmoplas
Interplast Co Ltd PRODUCT INFORMATION & DESIGN DATA FOR GRP PIPES & FITIINGS
Manufacturer details
Name of Manufacturer Cosmoplast Industrial Co. L.L.C
Continuous Dual Helical Filament
Manufacturing Process Wound Process
Product 100mm; PN 10; SN 5,000 N/~
Document no GRP!100Pl0S05K; Rev 2; 28/09/11
Design reference AWWA Manual M45
Standards Specfication for filament wound fiberglass Pipe ASTM D 2996
Manufacturing process for bends & fittings Mitered
Joint Type PL/PL
PIPE WALL STRUCTURE
Nominal Length of Standard Pipe 9.00 M
Total Length of Pipe 9.000 M
Socket Length PL/PL
Spigot Length PL/PL
Rubber Type N/A
Minimum Total Wall Thickness 10.00 mm
Inner Liner :- Thickness (minimum) 1.00 mm
Veil: GlassType 10% C- Glass
Resin type 90% Isopthalic
CSM : Glass type 45 - 50% E- Glass
resin Type 50 - 65% Isopthalic
Average Glass in Liner 25 - 30 %
Average Resin 65-70 %
Structural Wall :- Thickness (minimum) 8.5 mm
Glass type 70% E-Glass (Rovings)
Resin type 30% Isopthalic
Outer Liner :- Thickness (minimum) 0.5 mm
Glass type 10% C- Glass
Resin type 90% Isopthalic
E~ - .. ~-- _. _--- -- --.-=-=3 --- i-J-} }rr--~=
......".., ~L--- _ __ __ ___ ___ _ _ __ __ ____
___ -_ _--J~
_... ,. _. ..- - - . . ~-~ OA/ QC Department
..
~~~ Cosmoplast Industrial Co. -=-
Page 1 of 1
---
---
---
--
--
--
--
--
--
--
Cosmoplast Industrial Co osmoplas
Interplast Co Ltd '.r..~)[ '~R® ID ldJ:(\Jir~ IN R@ RNi~i'f@ m&_ s .~ - ~
Manufacturer details -Name of Manufacturer Cosmoplast Industrial Co. L.L.C
Continuous Dual Helical Filament
Manufacturing Process Wound Process
Product 200mm; PN 10; SN 5,000 N/JVf
Document no GRP!200P10S05K; Rev 2; 28/09/11
Design reference AWWA Manual M45
Standards Specfication for filament wound fiberglass Pipe ASTI\J\ D 2996
Manufacturing process for bends & fittings Mitered
Joint Type PL/PL
PIPE WALL STRUCTURE -- - -~
Nominal Length of Standard Pipe 9.00 M
Total Length of Pipe 9.000 M
Socket Length PL/PL
Spigot Length PL/PL
Rubber Type N/A
Minimum Total Wall Thickness 10.00 mm
Inner Liner :- Thickness (minimum) 1.00 mm
Veil: Glass Type 10% C- Glass
Resin type 90% Isopthalic
CSM : Glass type 45 - 50% E- Glass
resin Type 50 - 65% Isopthalic
Average Glass in Liner 25 - 30 %
Average Resin 65-70 %
Structural Wall :- Thickness (minimum) 8.5 mm
Glass type 70% E- Glass (Rovings)
Resin type Isopthalic
Outer Liner :- Thickness (minimum)
30%
0.5 mm
Glass type 10% C-Glass
Resin type Isopthalic90% ...
[" ==- -~=- ..- =-==-~==-] J0-} }____= -.o=r-;-~_ :" l:l' -.----~.c.:='""--=-_==~ - = P_"_"l-- _ __ _ _'~_' __ p _ _ _ .. _ _ _ ----1
~~)QA/ QC Department ~ ~J
~Cosmoplast Industrial Co.
Page 1 of 1