Post on 17-Oct-2019
transcript
(( DAkkSDeutscheAkkreditierungsstelle
Deutsche Akkreditierungsstelle GmbH
Entrusted accordingto Section 8 subsection l AkkStelleG in connection with Section lsubsection l AkkStelleGBVSignatory to the Multilateral Agreements ofEA, ILAC and IAF for Mutual Recognition
The Deutsche Akkreditierungsstelle GmbH attests that the testing laboratory
Materialprüfanstalt für das Bauwesen (MPA BS)Beethovenstraße 52, 38106 Braunschweig
Special field l -Structures & Construction Materials
is competent under the terms of DIN EN ISO/IEC 17025:2005 to carry out tests in thefollowing fields:
mechanical, physical, hygric, thermic and chemico-physical tests on mineral constructionmaterials such äs aggregates, cements, concrete, steel fibre concrete, concrete products,bricks, mortars, plasters, screed, on load bearing walls and non load bearing lightpartitions, ceiling sheathings, pipe anchors, fixtures and manholes for road surfaces,construction steel and concrete steel, stainless steel, prestressed steel, concrete steelconnections, fibres for concrete, prestressed components, on concrete elements andstructures with respect to durability, on concrete steel components and structures inrelation to construction structures inspections, on restoration materials, constructionstructures sealing, on organic and inorganic construction products, on heat insulators andfibre cement products
Testing of construction products in accordance with the Construction Products Regulation(EU) No 305/2011 to defined harmonised conditions for the marketing of constructionproducts (Construction Products Regulation - CPR)
The accreditation certificate shall only apply in connection with the notice of accreditation of 16. 01. 2018with the accreditation number D-PL-11267-01 and is valid until 13. 11. 2021. It comprises the cover sheet,the reverse side ofthe cover sheet and the following annex with a total of 29 pages.
Registration number ofthe certificate: D-PL-11267-01-01
Berlin,08. 06. 2018
Dr. Heike Manke
Head of Division
Translation issued:
08. 06. 2018 Head
/
ivjsion
This document is a translation. The definitive Version is the original German accreditation certificate.
Seenotesoverleaf,
Deutsche Akkreditierungsstelle GmbH
Office Berlin
Spittelmarkt 1010117 Berlin
Office Frankfurt am Main
Europa-Allee 5260327 Frankfurt am Main
Office BraunschweigBundesallee 100
38116 Braunschweig
The publication of extracts of the accreditation certificate is subject to the prior written approval byDeutsche Akkreditierungsstelle GmbH (DAkkS). Exempted is the unchanged form of separatedisseminations ofthe cover sheet by the conformity assessment body mentioned overleaf.
No impression shall be made that the accreditation also extends to fields beyond the scope ofaccreditation attested by DAkkS.
The accreditation was granted pursuant to the Act on the Accreditation Body (AkkStelleG) of 31 July 2009(Federal Law Gazette l p. 2625) and the Regulation (EC) No 765/2008 ofthe European Parliament and ofthe Council of 9 July 2008 setting out the requirements for accreditation and market surveiltance relatingto the marketing of products (Official Journal of the European Union L 218 of 9 July 2008, p. 30). DAkkS isa signatorytothe Multilateral Agreements for Mutual Recognition ofthe European co-operation forAccreditation (EA), International Accreditation Forum (IAF) and International LaboratoryAccreditationCooperation (l LAG). The signatories to these agreements recognise each other's accreditations.
The up-to-date state of membership can be retrieved from the following websites:EA: www.european-accreditation.orgILAC: www. ilac. orgIAF: www. iaf. nu
K DAkkSDeutscheAkkreditierungsstelle
Deutsche Akkreditierungsstelle Gmbhl
Annex to the Accreditation Certificate D-PL-11267-01-01
According to DIN EN ISO/IEC 17025:2005
Period of validity: 16. 01. 2018 to 13. 11. 2021 Date of issue: 08.06.2018
Holder ofcertificate:
Materialprüfanstalt für das Bauwesen (MPA BS)Beethovenstraße 52, 38106 Braunschweig
Special field l -Structures & Construction Materials
Tests in the fields:
mechanical, physical, hygric, thermic and chemico-physical tests on mineral construction mate-rials such äs aggregates, cements, concrete, steel fibre concrete, concrete products, bricks, mor-tars, plasters, screed, on load bearing walls and non load bearing light partitions, ceiling sheath-ings, pipe anchors, fixtures and manholes for road surfaces, construction steel and concrete
steel, stainless steel, prestressed steel, concrete steel connections, fibres for concrete, pre-stressed components, on concrete elements and structures with respect to durability, on con-crete steel components and structures in relation to construction structures inspections, onrestoration materials, construction structures sealing, on organic and inorganic constructionproducts, on heat insulators and fibre cement products
Testing of construction products in accordance with the Construction Products Regulation (EU)No 305/2011 to defined harmonised conditions forthe marketing of construction products(Construction Products Regulation - CPR)
Abbreviations used: see last page
The testing laboratory is permitted, without being required to inform and obtain prior approvalfrom DAkkS, to use Standards or equivalent testing methods listed here with different issuedates.
The testing laboratory maintains a current list of all testing methods within the flexible scope ofaccreditation.
This document is a translation. The definitive version is the original German annex to the accreditation certificate. 1/29
(Annex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
Aggregates for mortar and concrete
DINEN 932-11996-11
DIN EN 932-21999-03
DIN EN 933-12012-03
DINEN 933-21996-01
Test for general properties of aggregates - Part l: Methods forsampling
Test forgeneral properties ofaggregates - Part 2: Methods forreducing laboratory samples
Tests for geometrical properties of aggregates - Part l: Determina-tion of particle size distribution - Sieving method
Test for geometrical properties of aggregates - Part 2: Determina-tion of particle size distribution; test sieves, nominal size of aper-tures
DIN EN 933-42015-01
DIN EN 933-52005-02
DIN EN 933-71998-05
DIN EN 1097-31998-06
DIN EN 1097-42008-06
DIN EN 1097-52008-06Corrigendum l2008-09
Tests for geometrical properties of aggregates - Part 4: Determina-tion of particle shape - Shape index
Tests for geometrical properties of aggregates - Part 5: Determina-tion of percentage of crushed and broken surfaces in coarse ag-gregate particles
Tests for geometrical properties of aggregates - Part 7: Determina-tion of shell content; percentage of Shells in coarse aggregates
Tests for mechanical and physical properties of aggregates -Part 3: Determination of loose bulk density and voids
Tests for mechanical and physical properties of aggregates -Part 4: Determination of the voids of dry compacted filier
Tests for mechanical and physical properties of aggregates -Part 5: Determination of the water content by drying in a ventilat-ed oven
DIN EN 1097-62013-09
DIN EN 1097-72008-06Corrigendum l2008-09
Tests for mechanical and physical properties of aggregates -Part 6: Determination of particle density and water absorption
Tests for mechanical and physical properties of aggregates - Part 7:Determination of the particle density of filier - Pyknometer method
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08.06. 2018
- Translation - 2/29
KAnnex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
DIN EN 1367-12007-06
DIN EN 123712010-07
Tests for thermal and weathering properties of aggregates -Part l: Determination of resistance to freezing and thawing
Natural stone test methods - Determination of frost resistance
DIN EN 137552008-08
DIN 520982005-06
DIN 520992013-10
Natural stone test methods - Determination of water absorptionat atmospheric pressure
Aggregates test methods - Determination of particle size distribu-tion bywetsieving
Testing of aggregates - Testing with respect to purity
DIN 521022013-10
DIN 521062013-12
Test methods for aggregates - Determination of dry bulk densityby the cylinder method and calculation of the ratio of density
Testing of aggregates - Test methods for the assessment of theweathering resistance
Concrete
2.1 Normal concrete
DIN EN 12350-12009-08
Testing fresh concrete - Part l: Sampling
DIN EN 12350-22009-08
Testing fresh concrete - Part 2: Slump-test
DIN EN 12350-42009-08
Testing fresh concrete - Part 4: Degree of compactability
DIN EN 12350-52009-08
Testing fresh concrete - Part 5: Flow table test
DIN EN 12350-62011-03
Testing fresh concrete - Part 6: Density
DIN EN 12350-72009-08
Testing fresh concrete - Part 7: Air content - Pressure methods
Period ofvalidity: 16.01. 2018 to 13. 11. 2021Date of issue: 08.06.2018
-Translation - 3/29
DAkkSAnnex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
DIN EN 12350-82010-12
Testing fresh concrete - Part 8: Self-compacting concrete - Slump-flow test
DIN EN 12350-92010-12
Testing fresh concrete - Part 9: Self-compacting concrete - V-funnel test
DIN EN 12350-102010-12
Testing fresh concrete - Part 10: Self-compacting concrete - L boxtest
DIN EN 12350-112010-12
DIN EN 12350-122010-12
Testing fresh concrete - Part 11: Self-compacting concrete - Sievesegregation test
Testing fresh concrete - Part 12: Self-compacting concrete - J-ringtest
DIN EN 12390-12012-12
DIN EN 12390-22009-08Corrigendum l2012-02AmendmentA20
2015-12
Testing hardened concrete - Part l: Shape, dimensions and otherrequirements for specimens and moulds
Testing hardened concrete - Part 2: Making and curing specimensfor strength tests
DIN EN 12390-32009-07Corrigendum l2011-11
Testing hardened concrete - Part 3: Compressive strength oftestspecimens
DIN EN 12390-52009-07
Testing hardened concrete - Part 5: Flexural strength oftest spec-imens
DIN EN 12390-62010-09
DIN EN 12390-72009-07
Testing hardened concrete - Part 6: Tensile Splitting strength oftest specimens
Testing hardened concrete - Part 7: Density of hardened concrete
DIN EN 12390-82009-07
DIN CEN/TS 12390-92017-05
Testing hardened concrete - Part 8: Depth of penetration of waterunder pressure
Testing hardened concrete - Part 9: Freeze-thaw resistance - Scal-ing (pre-standard)
Period ofvalidity: 16. 01. 2018 to 13. 11.2021Date of issue: 08.06.2018
- Translation - 4/29
KAnnex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
DIN EN 12390-132014-06
CEN/TR 151772006-06
RILEM-Guideline CPC-71975
Testing hardened concrete - Part 13: Determination ofsecantmodulus of elasticity in compression
DIN-Technical report, Testing the freeze-thaw resistance ofcon-crete - Internat structural damage
Direct tension of concrete specimens (axial tensile strength)
2. 2 Sprayed concrete
DIN EN 14488-12005-11
Testing sprayed concrete - Part l: Sampling fresh and hardenedconcrete
DI N E N 14488-32006-09
DI N E N 14488-42008-08
Testing sprayed concrete - Part 3: Flexural strengths (first peak,ultimate and residual) offibre reinforced beam specimen
Testing sprayed concrete - Part 4: Bond strength of cores by directtension
DIN EN 14488-62006-09
Testing sprayed concrete - Part 6: Thickness ofconcrete on a sub-strate
DIN EN 14488-72006-08
Testing sprayed concrete - Part 7: Fibre content offibre reinforcedconcrete
2. 3 Fibre concrete
DIN EN 146512007-12
DIN EN 147212007-12
Test method for metallic fibre concrete - Measuring the flexuraltensile strength (limit or proportionality (LOP), residual)
Test method for metallic fibre concrete - Measuring the fibre con-tent in fresh and hardened concrete
DIN EN 14845-12007-09
Test methods for fibres in concrete - Part l: Reference concretes
DIN EN 14845-22006-11
Test methods for fibres in concrete - Part 2: Effect on concrete
DIN 1048-51991-06
Testing concrete; testing of hardened concrete (specimens pre-pared in mould)(withdrawn Standard)
Period ofvalidity: 16.01.2018 to 13.11.2021Date of issue: 08. 06. 2018
- Translation - 5/29
DAkkSAnnex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
RILEMTC162-TDF2000-03
Test and Design Methodes forSteel Fibre Reinforced Concrete
Durability ofconcrete components and structures
DIN 521082010-05
RILEM-Recommendation
CPC-181988
Testing of inorganic non-metallic materials - Wear test using thegrinding wheel according to Böhme - Grinding wheel method
Measurement of hardened concrete-Carbonation depth(Determination ofcarbonation depth)
RILEM TC 176-IDC2004-12
Test methods offrost resistance ofconcrete: CIF-TestiCapillarysuction, internal damage and freeze thaw test
RILEM TC 117-FDC1997
Test method of frost resistance of concrete - capillary suction ofde-icing solution and freeze thaw (CDF-Test)
FB1-PA0032016-02
Location of concrete steel reinforcement using magnetic inductivemethod
FB1-PA0092016-02
Test offrost resistance ofconcrete using CIF-Test
FB1-PA0102016-02
Test of frost thaw agent resistance of concrete using CDF-Test
Tests of concrete components and structures in relation to Inspections
DIN EN 12504-12009-07
Testing concrete in structures - Part l: Cored specimens - Taking,examining and testing in compression
DIN EN 12504-22012-12
Testing concrete in structures - Part 2: Non-destructive testing -Determination of rebound number
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
- Translation - 6/29
([Annex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
Grouting mortar
DIN EN 4452008-01
Grout for prestressing tendons - Test methods
Artificially produced mineral construction products-concrete products(aerated concrete, light concrete, concrete blocks, ancillary components for masonry )
DIN EN 846-22000-08
DIN EN 846-32010-08
DI N E N 846-42005-01
DIN EN 846-52012-11
DIN EN 846-62012-11
DIN EN 846-72012-11
DIN EN 846-82006-10
DIN EN 846-92016-08
Methods of tests for ancillary components for masonry - Part 2:Determination of bond strength of prefabricated bed joint rein-forcement in mortarjoints
Methods of tests for anciltary components for masonry - Part 3:Determination of shear load capacity of welds in prefabricatedbed joint reinforcement
Methods of test for ancillary components for masonry - Part 4:Determination of load capacity and load-deflection characteristicsof Straps
Methods of test for ancillary components for masonry - Part 5:Determination oftensile and compressive load capacityand loaddisplacement characteristics of wall ties (couplet test)
Methods of test for ancillary components for masonry - Part 6:Determination oftensile and compressive load capacityand loaddisplacement characteristics of wall ties (single end test)
Methods of test for ancillary components for masonry - Part 7:Determination of shear load capacity and load displacement char-acteristics of shear ties and slip ties (couplet test for mortar jointconnections)
Methods of test for ancillary components for masonry - Part 8:Determination of load capacity and load-deflection characteristicsofjoist hangers
Methods of test for ancillary components for masonry - Part 9:Determination offlexural resistance and shear resistance of lintels
DIN EN 846-102000-08
Methods of test for ancillary components for masonry - Part 10:Determination of load capacity and load deflection characteristicsof brackets
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08.06.2018
-Translation - 7/29
((Annex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
DIN EN 846-112000-08
Methods of test for ancillary components for masonry - Part 11:Determination of dimensions and bow of lintel
DIN EN 846-142012-11
DIN EN 13382003-08Corrigendum l2006-11
Methods of test for ancillary components for masonry - Part 14:Determination of the initial shear strength between the prefabri-cated part of a composite lintel and the masonry above it
Concrete paving blocks - Requirements and test methods(without annex G and l)
DIN EN 13392003-08Corrigendum l2006-11
Concrete paving flags - Requirements and test methods(without annex G and l)
DIN EN 13402003-08Corrigendum l2006-11
Concrete kerb units; Requirements and test methods(withoutannexG and l)
DIN EN 13432013-03AmendmentA20
2014-07
Kerbs of natural stone for external paving - Requirements and testmethods
DIN EN 13531997-02
Determination of moisture content of autoclaved aerated con-crete
DIN EN 14332005-09
Drainage channels for vehicular and pedestrian areas - Classifica-tion, design and testing requirements, marking and evaluation ofconformityhere: clause 9
DIN 42811998-08
Concrete for prefabricated sewage units - Manufacture, require-ments, testing and quality control
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
- Translation - 8/29
((Annex to the accreditation certificate D-PL-112G7-01-01
DAkkSDeutscheAkkreditierungsstelle
Metallic materials
7. 1 Mechanical tests
DIN EN 10002-12001-12
DIN EN ISO 6892-12017-02
DIN EN ISO 74382016-07
Metallic materials -Tensile testing - Part l: Method oftesting (atambient temperature)(withdrawn Standard)
Metallic materials -Tensile testing - Part l: Method oftest atroom temperature, method B
Metallic materials - Bend test
DIN ISO 78012008-10
Metallic materials; Wire; Reverse bend test
DIN ISO 78022014-11
Metallic materials - Wire - Wrapping test
ASTM A 370a2013
Standard test methods and definitions for mechanical testingof steel products(Testing ofmechanicals properties of steel products)
7.2 Reinforcing steel
DIN EN ISO 15630-12011-02
Steel for the reinforcement and prestressing of concrete - Testmethods - Part l: Reinforcing bars, wire rod and wirehere: without clause 9
DIN EN ISO 15630-22011-02
Steel for the reinforcement and prestressing of concrete - Testmethods - Part 2: Welded fabric
here: without clause 9
7.3 Reinforced steel couplings
DIBt-Richtlinie2007-05
Centre of Competence for Constrution (DIBt) Guideline for thenational technical approvals and surveillances of mechanical con-crete steel connections
here: clause 2.0
DIBt-CUAP2005-05
Couplings for standardised reinforcing bars ETA requestNo 03.01/02; second draft: May 2005, Kap. 4
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
- Translation - 9/29
((Annex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
7. 4 Prestressed steel
DIN EN ISO 15630-32011-02
Steel for the reinforcement and prestressing of concrete - Testmethods - Part 3: Prestressing steelhere: withoutclausel2
BS 58962012-05
High tensile steel wire and strand for theprestressing ofconcrete. Specification
NEN 38682001-12
Voorspanstaal (Prestressing steel)
NF A 05-3021981-12
Armatures de precontrainte - Essai de corrosion sous contrainte äl'eau distillee Spannbewehrung(reinforcements - corrosion test using distilled water)
XP A 35-045-12000-02
ASTM A1061/A1061M2016
Produits en acier - Armatures de precontrainte - Partie l: Prescrip-tionesgenerals
(steel products reinforcements - Part l: general requirements)Annex A, B and C
Standard Test Methods forTesting Multi-Wire Steel PrestressingStrand
7. 5 Steel fibres
EN 10218-12012-03
Steel wire and wire products - General - Part l: Test methods
8. Cables
ETAG 0132002-06
Guideline for European Technical Approval of post tensioning kits forprestressing of structuresAnnex B
TL Seile VerkehrsblattNr. B 5229edition 1994
Technical supplier specification for fully locked bridge rope, Minis-try of Transport, Roadworks Dept., Transport Gazette DocNo B 5229(according clause 3. 1.5 + 5.4. 1.3 and annex 2+9)
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
-Translation - 10/29
KAnnex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
FIBCEB-FIB2005-01
Acceptance of stay cable Systems using prestressing steelsclause 6
PTI DC.45. 1-122012
PTI Recommendations for Stay Cable Design, Testing and Installa-tion
Wall and ceiling finishes and partitions
DIN EN 5202009-12
Gypsum plasterboards - Definitions, requirements and test meth-ods
DIN EN 139642014-08
DIN EN 14179-12016-12
DIN EN 15283-12009-12
Suspended ceilings - Requirements and test methods(withoutannex D)
Glass in building - Heat soaked thermally toughened soda limesilicate safety glass - Part l: Definition and description
Gypsum boards with fibrous reinforcement - Definitions, require-ments and test methods - Part l: Gypsum boards with mat rein-forcement
DIN EN 15283-22009-12
Gypsum boards with fibrous reinforcement - Definitions, require-ments and test methods - Part 2: Gypsum fibre boards
ETAG 0032013-07
Guideline for European Technical Approval of internal partitionkits for use äs non-loadbearing walls
ETAG 0042000-03
Guideline for European Technical Approval of external thermalinsulation composite Systems with rendering
10 Piping anchorages
RAL-GZ 6552008-04
Piping anchorages - quality control (according clause B 3. 2. 4,C 3.4.4, D 3.3.3, E 3.3.4)
11 Construction waterproofing
DIN EN 495-52013-08
Flexible sheets for waterproofing - Determination of foldability atlow temperature - Part 5: Plastic and rubber sheets for roof wa-terproofing
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
-Translation - 11/29
l!Annex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
DINEN8262013-05
DIN EN 1107-11999-10
DIN EN 1107-22001-04
Thermal insulating products for building applications - Determina-tion ofcompression behavior
Flexible sheets for waterproofing - Determination of dimensionalstability - Part l: Bitumen sheets for roof waterproofing
Flexible sheets for waterproofing - Determination of dimensionalstability - Part 2: Plastic and rubber sheets for roof waterproofing
DIN EN 11081999-10
DIN EN 11092013-07
DIN EN 11102011-03
DIN EN 12962001-03
DIN EN 12972004-12
DIN EN 15482007-11
DIN EN 18472010-04
DIN EN 1848-11999-12
DIN EN 1848-22001-09
Flexible sheets for waterproofing - Bitumen sheets for roof water-proofing - Determination of form stability under cyclical tempera-ture changes
Flexible sheets for waterproofing - Bitumen sheets for roof water-proofing - Determination offlexibility at low temperature
Flexible sheets for waterproofing - Bitumen sheets for roof water-proofing - Determination offlow resistance at elevated tempera-ture
Flexible sheets for waterproofing - Bitumen, plastic and rubbersheets for roofwaterprofing - Method for artificial ageing by longterm exposure to elevated temperature
Flexible sheets for waterproofing - Bitumen, plastic and rubbersheets for roof waterproofing - Method of artificial ageing by langterm exposure to the combination of UV radiation, elevated tem-perature andwater
Flexible sheets for waterproofing - Plastic and rubber sheets forroof waterproofing - Method for exposure to bitumen
Flexible sheets for waterproofing - Plastics and rubber sheets forroofwaterproofing - Methods for exposure to liquid chemicals,includingwater
Flexible sheets for waterproofing - Determination of length, widthand straightness - Part l: Bitumen sheets for roofwaterproofing
Flexible sheets for waterproofing - Determination of length, width,straightness and flatness - Part 2: Plastic and rubber sheets forroofwaterproofing
DIN EN 1849-1
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08.06.2018
Flexible sheets for waterproofing - Determination ofthickness and
-Translation- 12/29
((Annex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditieru ngsstel le
2000-01
DIN EN 1849-22010-04
DIN EN 1850-11999-12
DIN EN 1850-22001-09
DIN EN 19282000-07
DI N EN 12004-22017-05
mass per unit area - Part l: Bitumen sheets for roof waterproofing
Flexible sheets for waterproofing - Determination of thickness andmass per unit area - Part 2: Plastic and rubber sheets
Flexible sheets for roofing - Determination of visible defects -Part l: Bitumen sheets for roof waterproofing
Flexible sheets for waterproofing - Determination of visible de-fects - Part 2: Plastic and rubber sheets for roofwaterproofing
Flexible sheets for waterproofing - Bitumen, plastic and rubbersheets for roof waterproofing - Determination of watertightness
Adhesives for tiles - Part 2: Test methods
DIN EN 12310-11999-11
DIN EN 12310-22000-12
DIN EN 12311-11999-11
DIN EN 12311-22013-11
DIN EN 12316-11999-11
DIN EN 12316-22013-08
DIN EN 12317-11999-11
DIN EN 12317-22010-12
Flexible sheets for waterproofing - Part l: Bitumen sheets for roofwaterproofing; determination of resistance to tearing (nail shank)
Flexible sheets for waterproofing - Determination of resistance totearing- Part 2: Plastic and rubber sheets for roof waterproofing
Flexible sheets for waterproofing - Part l: Bitumen sheets for roofwaterproofing; Determination oftensile properties
Flexible sheets for waterproofing - Determination of tensile prop-erties - Part 2: Plastic and rubber sheets for roofwaterproofing
Flexible sheets for waterproofing - Part l: Bitumen sheets for roofwaterproofing; determination of peel resistance ofjoints
Flexible sheets for waterproofing - Determination of peel re-sistance of joints - Part 2: Plastic and rubber sheets for roof wa-terproofing
Flexible sheets for waterproofing - Part l: Bitumen sheets for roofwaterproofing; determination ofshear resistance ofjoints
Flexible sheets for waterproofing - Determination of shear re-sistance of joints - Part 2: Plastic and rubber sheets for roof wa-terproofing
DIN EN 12691 Flexible sheets for waterproofing - Bitumen, plastic and rubber
Period ofvalidity: 16.01.2018 to 13. 11.2021Date of issue: 08. 06. 2018
- Translation - 13/29
((DAkkSAnnex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
2006-06
DIN EN 127302015-06
DIN EN 131112010-11
sheets for roof waterproofing - Determination of resistance toimpact
Flexible sheets for waterproofing - Bitumen, plastic and rubbersheets for roof waterproofing - Determination of resistance tostatic loading
Flexible sheets for waterproofing - Underlays for discontinuousroofing and walls - Determination of resistance to water penetra-tion
DIN EN 133922001-12
Textiles - Monofilaments - Determination of linear density
DIN EN 13859-12014-07
DIN EN 13859-22014-07
DIN EN 138972005-02
DIN EN 141962016-08
DIN EN 148912017-05
DIN EN 15651-12017-07
DIN EN 15651-22017-07
DIN EN 15651-32017-07
Flexible sheets for waterproofing - Definitions and characteristicsof underlays - Part l: Underlays for discontinuous roofing
Flexible sheets for waterproofing - Definitions and characteristicsof underlays - Part 2: Underlays for walls
Flexible sheets for waterproofing - Bitumen, plastic and rubbersheets for roof waterproofing - Determination of watertightnessafter stretching at low temperature
Geosynthetics - Test methods for measuring mass per unit area ofclay geosynthetic barriers
Liquid applied water impermeable products for use beneath ce-ramic tiling bonded with adhesives - Requirements, test methods,assessment and verification of constancy of performance, classifi-cation and markingAnnex 7 (A. 7): Watertightness
Sealants for non-structural use in joints in buildings and pedestri-an walkways - Part l: Sealants for facade elements
Sealants for non-structural use in joints in buildings and pedestri-an walkways - Part 2: Sealants for glazing
Sealants for non-structural use in joints in buildings and pedestri-an walkways - Part 3: Sealants for sanitaryjoints
DIN EN 15651-4 Sealants for non-structural use in joints in buildings and pedestri-
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08.06.2018
- Translation - 14/29
K DAkkS
Annex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
2017-07 an walkways - Part 4: Sealants for pedestrian walkways
DIN EN 29073-31992-08
DIN 7864-11984-04
Textiles; test method for nonwovens; part 3: determination oftensile strength and elongatio
Sheets of elastomers for waterproofing; terms of delivery
DIN 7865-22015-02
DIN 167262017-08
Elastomeric-Waterstops for sealingjoints in concrete - Part 2: Ma-terial specifications and testing
Plastic sheets - Testing
DIN 533702006-11
DIN 533772015-04
Testing of plastics films - Determination of the thickness by me-chanical scanning
Testing of plastic films - Determination of dimensional stability
DIN 535042009-10
Testing of rubber- determination of tensile strength at break,tensile stress at yield, elongation at break and stress values in atensile test
DIN EN ISO 1392011-10
Textiles - Standard atmospheres for conditioning and testing
DIN EN ISO 1782013-09
Plastics- Determination offlexural properties
DIN EN ISO 527-12012-06
DIN EN ISO 527-22012-06
DIN EN ISO 527-32003-07
Plastics - Determination of tensile properties - Part l: Generalprinciples
Plastics - Determination of tensile properties - Part 2: Test condi-tions for moulding and extrusion plastics
Plastics - Determination of tensile properties - Part 3: Test condi-tions for films and sheets
DIN EN ISO 527-41997-07
Plastics - Determination of tensile properties - Part 4: Test condi-tions for Isotropie and anisotropic fibre-reinforced plastic compo-sites
DIN EN ISO 846 Plastics - Evaluation ofthe action of microorganisms
Period ofvalidity: 16.01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
- Translation - 15/29
((Annex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
1997-10
DIN EN ISO 20622010-04
DINEN ISO 28132015-02
Textites - Yarns from packages - Determination ofsingle-endbreaking force and elongation at break using constant rate of ex-tension (CRE) tester
Paints and varnishes - Determination of gloss value at 20°, 60°and85°
DIN EN ISO 28152003-10
Paints and varnishes - Buchholz indentation test
DINEN ISO 46242016-08
Paints and varnishes - Pull-off test for adhesion
DINEN ISO 4892-32016-10
DIN EN ISO 73892016-10
Plastics - Methods of exposure to laboratory light sources - Part 3.Fluorescent UV lamps
Building construction - Jointing products - Determination of elasticrecoveryofsealants
DIN EN ISO 73902004-04
Building construction - Jointing products - Determination of re-sistance to flow of sealants
DINEN ISO 83392005-09
DIN EN ISO 83402005-09
Building construction - Sealants - Determination of tensile proper-ties (Extension to break)
Building construction - Sealants - Determination of tensile proper-ties at maintained extension
DIN EN ISO 98622005-05
Geosynthetics - Sampling and preparation oftest specimens
DIN EN ISO 9863-12016-12
DIN EN ISO 98642005-05
DIN EN ISO 105632017-09
Geosynthetics - Determination of thickness at specified pressures -Part l: Single layers
Geosynthetics - Test method for the determination of mass perunit area ofgeotextiles and geotextile-related products
Buildings and civil engineering works - Sealants - Determination ofchange in mass and volume
DIN EN ISO 10590 Building construction - Sealants - Determination oftensile proper-
Period ofvalidity: 16.01.2018 to 13.11.2021Date of issue: 08. 06. 2018
-Translation - 16/29
dAnnex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
2005-10 ties of sealants at maintained extension after immersion in water
DIN EN ISO 105912005-10
DIN EN ISO 114312003-01
DIN EN ISO 122362006-11
Building construction - Sealants - Determination of adhe-sion/cohesion properties of sealants after immersion in water
Building construction - Jointing products - Determination of adhe-sion/cohesion properties of saelants after exposure to heat, waterand artificial light through glass
Geosynthetics - Static puncture test
DIN EN ISO 13426-22005-08
DIN EN ISO 141252011-05
DIN EN ISO 17892-12015-03
Geotextiles and geotextile-related products - Strength of internalstructural junctions - Part 2: Geocomposites
Fibre-reinforced plastic composites - Determination offlexuralproperties
Geotechnical investigation and testing - Laboratory testing of soil -Part l: Determination ofwater content
DIN ISO 235292012-10
DIN EN ISO 25619-22015-12
ETAG 005(part l to 8)
ETAG 005-12004-03
ETAG 005-22004-03
ETAG 005-32004-03
ETAG 005-4
Rubber - General procedures for preparing and conditioning testpieces for physical test methods
Geosynthetics - Determination ofcompression behaviour- Part 2:Determination ofshort-term compression behaviour
Guideline for European Technical Approval of liquid applied roofwaterproofing kit
Part l: General
Test done according to test Programme in consultation with ETAapproved bodies
Part 2: Specific stipulations for Kits bases on Polymer ModifiedBitumen
Test done according to test Programme in consultation with ETAapproved bodies
Part 3: Specific stipulations for Kits based on Glass Reinforced Re-silient Unsaturated Polyester ResinTest done according to test Programme in consultation with ETAapproved bodies
Part 4: Specific stipulations for Kits on Flexible Unsaturated Polyes-
Period ofvalidity: 16.01.2018 to 13. 11.2021Date of issue: 08. 06. 2018
- Translation - 17/29
((Annex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
2004-03 terTest done according to test Programme in consultation with ETAapproved bodies
ETAG 005-52004-03
ETAG 005-62004-03
ETAG 005-72004-03
ETAG 005-82004-03
Richtlinie DVS 2201-1Beiblatt 1-51989-02
Part 5: Specific stipulations for Kits based on Hot Applied PolymerModified Bitumen
Test done according to test Programme in consultation with ETAapproved bodies
Part 6: Specific stipulations for Kits based on PolyethuraneTest done according to test Programme in consultation with ETAapproved bodies
Part 7: Specific stipulations for Kits based on Bitumen EmulsionsandSolutions
Test done according to test Programme in consultation with ETAapproved bodies
Part 8: Specific stipulations for Kits based on Water DispersablePolymersTest done according to test Programme in consultation with ETAapproved bodies
Testing of semifinished products of thermoplastics - Bases - indica-tions
Richtlinie DVS 2201-21985-07
Richtlinie DVS 2203-22010-08
Richtlinie DVS 2203-51999-08
Richtlinie DVS 2203-62008-01
Testing of semi-finished products of thermoplastics - Weldability -Test methods- Requirements
Testing of welded joints between panels and pipes made of ther-moplastics - Tensile test
Testing of welded joints of thermoplastics plates and tubes -Technological bend test
Testing ofjoints between polymeric materials - Shear and peelingtests
Richtlinie DVS 2203-6Bbl.l2016-08
Testing ofjoints between polymeric materials -Torsion sheartest,radial peel test and linear shear test for sleeve welding with incor-porated electric heating element and heated tool sleeve weldedjoints
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08.06.2018
- Translation - 18/29
((Annex to the accreditation certificate D-PL-11267-01-01
DAkkSDeutscheAkkreditierungsstelle
Richtlinie DVS 2225-12016-09
Richtlinie DVS 2225-21992-08
Richtlinie DVS 2225-42016-09
Richtlinie DVS 2226-12000-09
Joining of lining membranes - Made from polymeric materials (ge-omembranes) in geotechnical and hydraulic application - Welding,bonding by adhesives, vulcanizing
Joining of lining membranes - Made of polymer materials in ge-otechnical and hydraulic engineering - Site testing
Welding of sealing sheets made of polyethylene (PE) for the seal-ing of dumps and contaminated sites
Testing of fused joints on liners of polymer materials - Testing pro-cedure, requirements
Richtlinie DVS 2226-21997-07
Testing of fused joints on liners of polymer materials - Lap sheartest
Richtlinie DVS 2226-31997-07
Test of fusions on PE liners - Peeling test
12 Restoration materials
DIN EN 19312001-03
DIN EN 120862013-06
DIN 53122-12001-08
Flexible sheets for waterproofing - Bitumen, plastic and rubbersheets for roof waterproofing - Determination of water vapourtransmission properties
Thermal insulating products for building applications - Determina-tion ofwatervapourtransmission properties
Testing of plastics and elastomer films, paper, board and othersheet materials - Determination of water vapour transmission -Part l: Gravimetric method
DIN EN ISO 2884-12006-09
Paints and varnishes - Determination ofviscosity using rotaryvis-cometers - Part l: Cone-and-plate viscometer operated at a highrateofshear
DINEN ISO 32191994-10
Plastics - Polymers/resins in the liquid state or äs emulsions ordispersions - Determination ofviscosity using a rotational viscom-eter with defined shear rate
E DIN EN ISO 125722017-05
ETAG 022-1
Hygrothermal performance of building materials and products -Determination of water vapour transmission properties - Cupmethod (draft)Guideline for European Technical Approval ofwatertight covering
Period ofvalidity: 16.01.2018 to 13. 11.2021Dato of issue: 08.06. 2018
-Translation - 19/29
(( DAkkSAnnex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
2007-04
ETAG 022-22010-11
kits for wetroom ftoors and/or walls - Part l: Liquid applied cover-ings with or without wearing surfaceTest done according to test Programme in consultation with ETAapproved bodies
Guideline for European Technical Approval ofwatertight coveringkits for wetroom floors and/or walls - Part 2: Kits based on flexiblesheets
Test done according to test Programme in consultation with ETAapproved bodies
ETAG 022-32010-11
Guideline for European Technical Approval ofwatertight coveringkits for wetroom floors and/or walls - Part 3: Kits based on inher-ently watertight boardsTest done according to test Programme in consultation with ETAapproved bodies
13 Testing of inorganic construction materials
DIN EN 196-22013-10
DIN EN 1744-12013-03
DIN EN 13279-22014-03
Method of testing cement - Part 2: Chemical analysis of cement(only clause 4.4. 1, 4.4. 2 and 4.4.)
Tests for chemical properties of aggregates - Part l: Chemicalanatysis(only clause 7 to 10, 12 and 17)
Gypsum binders and gypsum plasters - Part 2: Test methods
DIN EN ISO 151482016-12
Hygrothermal performance of building materials and products -Determination ofwaterabsorption coefficient by partial immersion
14 Testing of organic construction materials
DIN EN 17671999-09
DIN EN 126142005-01
DIN EN ISO 1133-1
Products and Systems for the protection and repair of concretestructures - Test methods - Infrared analysis
Products and Systems for the protection and repair of concretestructures - Test methods - Determination of glass transition tem-peratures of polymers
Plastics - Determination ofthe melt mass-flow rate (MFR) and
Period ofvalidity: 16.01.2018 to 13.11.2021Date of issue: 08. 06. 2018
- Translation - 20/29
(( DAkkSAnnex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
2012-03 melt volume-flow rate (MVR) of thermoplastics - Part l: Standardmethod
DIN EN ISO 1183-12013-04
Plastics - Methods for determining the density of non-cellular plas-tics - Part l: Immersion method, liquid pyknometer method andtitration method
DINEN ISO 32512008-06
Paints, varnishes and plastics - Determination of non-volatile-matter content
DIN EN ISO 64272014-08
DIN EN ISO 11357-32013-04
DIN EN ISO 11357-62013-04
DIN EN ISO 11358-12014-10
Plastics - Determination of matter extractable by organic solvents(conventional methods)
Plastics - Differential scanning calorimetry (DSC) - Part 3: Determi-nation of temperature and enthalpy of melting and crystallization
Plastics - Differential scanning calorimetry (DSC) - Part 6: Determi-nation of oxidation induction time (isothermal OIT) and oxidationinduction temperature (dynamic OIT)
Plastics - Thermogravimetry (TG) of polymers - Part l: Generalprinciples
15 Testing of thermal insulating products
DINEN8222013-05
DIN EN 8232013-05
Thermal insulating products for building applications - Determina-tion of length and width
Thermal insulating products for building applications - Determina-tion ofthickness
DIN EN 8242013-05
DIN EN 8252013-05
Thermat insulating products for building applications - Determina-tion ofsquareness
Thermal insulating products for building applications - Determina-tion offlatness
DIN EN 16022013-05
DIN EN 16032013-05
DIN EN 1609
Thermal insulating products for building applications - Determina-tion ofthe apparent density
Thermal insulating products for building applications - Determina-tion of dimensional stability under constant normal laboratoryconditions (23 °C/ 50 % relative humidity)Thermal insulating products for building applications - Determina-
Period ofvalidity: 16.01. 2018 to 13. 11. 2021Date of issue: 08.06.2018
- Translation - 21/29
DAkkSAnnex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
2013-05
DIN EN 120852013-06
DIN EN 120872013-06
DIN EN 126642001-05
tion of short term water absorption by partial Immersion
Thermal insulating products for building applications - Determina-tion of linear dimensions of test specimen
Thermal insulating products for building applications - Determina-tion of lang term water absorption by immersion
Thermal performance of building materials and products - Deter-mination ofthermal resistance by means ofguarded hot plate andheat flow meter methods - Dry and moist products with mediumand lowthermal resistance
DIN EN 126672001-05
Thermal performance of building materials and products - Deter-mination ofthermal resistance by means ofguarded hot plate andheat flow meter methods - Dry and moist products with mediumand lowthermal resistance
DIN EN 129392001-02
Thermal performance of building materials and products - Deter-mination ofthermal resistance by means ofguarded hot plate andheat flow meter methods - Thick products of high and mediumthermal resistance
16 Mortar, plastering and floor
16. 1 Masonry mortar and plastering mortars
DIN EN 196-12016-11
Methods oftesting cement - Part l: Determination ofstrength
DIN EN 196-32017-03
Methods of testing cement - Part 3: Determination of setting timesand soundness
DIN EN 1015-12007-05
DIN EN 1015-22007-05
DIN EN 1015-32007-05
DIN EN 1015-41998-12
Methods of test for mortar for masonry - Part l: Determination ofparticle size distribution (by sieve analysis)
Methods of test for mortar for masonry - Part 2: Bulk sampling ofmortars and preparation oftest mortars
Methods of test for mortar for masonry - Part 3: Determination ofconsistence of fresh mortar (by flow table)
Methods of test for mortar for masonry - Part 4: Determination ofconsistence offresh mortar (by plunger penetration)
Period ofvalidity: 16.01. 2018 to 13. 11. 2021Date of issue: 08.06.2018
- Translation - 22/29
( DAkkS
Annex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
DIN EN 1015-62007-05
DIN EN 1015-71998-12
Methods of test for mortar for masonry - Part 6: Determination ofbulk density of fresh mortar
Methods of test for mortar for masonry - Part 7: Determination ofair content of fresh mortar
DIN EN 1015-92007-05
Methods of test for mortar for masonry - Part 9: Determination ofworkable life and correction time offresh mortar
DIN EN 1015-102007-05
DIN EN 1015-112007-05
DIN EN 1015-122016-12
Methods of test for mortar for masonry - Part 10: Determination ofdry bulk density of hardened mortar
Methods of test for mortar for masonry - Part 11: Determination offlexural and compressive strength of hardened mortar
Methods of test for mortar for masonry - Part 12: Determination ofadhesive strength of hardened rendering and plastering mortars onSubstrate
DIN EN 1015-182003-03
Methods of test for mortar for masonry - Part 18: Determination ofwater absorption coefficient due to capillary action of hardenedmortar
DIN EN 1015-192005-01
Methods of test for mortar for masonry - Part 19: Determination ofwater vapour permeability of hardened rendering and plasteringmortars
DIN EN 1052-11998-12
DIN EN 1052-22016-08
DIN EN 1052-32007-06
DIN EN 1052-42000-09
DIN 18555-31982-09
Methods of test for masonry - Part l; Determination of compressivestrength
Methods of test for masonry - Part 2: Determination of flexuralstrength
Methods of test for masonry - Part 3: Determination of initial shearstrength
Methods of test for masonry - Part 4; Determination of shearstrength including damp proof course
Testing of mortars containing mineral binders; hardened mortars;determination offlexural strength, compressive strength and bulkdensity
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
- Translation - 23/29
(( DAkkSAnnex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
DIN 18555-41986-03
DIN 18555-61987-11
DIN 18555-71987-11
DIN 18555-91999-09
Testing of mortars containing mineral binders; hardened mortars;determination of linear and transverse strain and of deformation
characteristics of masonry mortars by the static pressure test
Testing of mortars containing mineral binders; determination ofbond strength of hardened mortar
Testing of mortars containing mineral binders; determination ofwater retentivity of freshly mixed mortar by the filter plate method
Testing of mortars containing mineral binders - Part 9: Hardenedmortars; determination ofthe mortar compressive strength in thebed joint
16.2 Floorscreeds
DIN EN 13892-12003-02
DIN EN 13892-22003-02
DIN EN 13892-32015-03
Methods of test for screed materials - Part l: Sampting, making andcuring specimens for test
Methods of test for screed materials - Part 2: Determination of flex-
ural and compressive strength
Methods of test for screed materials - Part 3: Determination ofwear resistance - Böhme
DIN EN 13892-82003-02
DIN 18560-12015-11
DIN 18560-22009-09Corrigendum l2012-05
Methods of test for screed materials - Part 8: Determination of bond
strength
Floorscreeds in buildingconstruction - Part l: General requirements,testing and construction, here: clause 6
Floor screeds in building construction - Part 2: Floor screeds and heat-ing floor screeds on insulation layers,here: clause 6
DIN 18560-32006-03
DIN 18560-42012-06
Floor screeds in building construction - Part 3: Bonded screed,here: clause 5, without 5. 2.6 and 5. 2.7
Floor screeds - Part 4: Screeds laid an separated layer,here: clause 5
Period ofvalidity: 16.01. 2018 to 13. 11. 2021Date of issue: 08.06. 2018
- Translation - 24/29
DAkkSAnnex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
DIN 18560-72004-04
Floor screeds - Part 7: Heavy-duty screeds (industrial screeds)here: clause 5
DIN 521082010-05
Testing of inorganic non-metallic materials - Wear test using the grind-ing wheel according to Böhme - Grinding wheel method
17. Fibre-cement products
DIN EN 492 Fibre-cement slates and fittings - Product specification and test methods2016-12
DIN EN 124672016-12
Fibre-cement flat sheets - Product specification and test methods
19 Testing of construction products (system of assessment and verification of constancy ofperformance 3) in accordance with the Construction Products Regulation (EU) No305/2011 to defined harmonised conditionsforthe marketing of construction products(Construction Products Regulation - CPR)
Decision / resolution of theCommission
1997/467/ECWaste water engineeringproducts outside buildings
1995/467/ECGypsum products
1997/740/ECMasonryand relatedproducts
System1 1 Technical specification
E N 1433:2002+A1:2005Drainage channels for vehicular and pedestrian areas -Classification, design and testing requirements, markingand evaluation ofconformityEN 520:2004+A1:2009Gypsum plasterboards - Definitions, requirements andtest methods
EN 15283-1:2008+A1:2009Gypsum boards with fibrous reinforcement - Definitions,
3 requirements and test methods - Part l: Gypsum boardswith mat reinforcement
EN 15283-2: 2008+A1:2009Gypsum boards with fibrous reinforcement - Definitions,requirements and test methods - Part 2: Gypsum fibreboards
EN 845-1:2013+A1:20163 Specification for ancillary components for masonry -
Part l: Wall ties, tension Straps, hangers and brackets
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08.06. 2018
- Translation - 25/29
Annex to the accreditation certificate D-PL-11267-01-01
K DAkkSDeutscheAkkreditierungsstelle
Decision / resolution of theCommission
1998/437/ECInternal and external wall
and ceilingfinishes
1999/90/ECMembranes
System11 Technical specification
EN 845-2:2013+Al:2016Specification for ancillary components for masonry-Part 2: LintelsEN 845-3:2013+A1:2016Specification for ancillary components for masonry-Part 3: Bed joint reinforcement of steel meshwork
EN 13964:2014Suspended ceilings - Requirements and test methods
EN 13707:2004+A2:2009Flexible sheets for waterproofing - Reinforced bitumensheets for roof waterproofing - Definitions and character-istics
EN 13859-1:2010Flexible sheets for waterproofing - Definitions and charac-teristics of underlays - Part l: Underlays for discontinuousroofingEN 13859-2:2010Flexible sheets for waterproofing - Definitions and charac-teristics of underlays - Part 2: Underlays for wallsEN 13956:2012Flexible sheets for waterproofing - Plastic and rubbersheets for roof waterproofing - Definitions and character-
3 istics
EM 13967:2012Flexible sheets for waterproofing - Plastic and rubberdamp proof sheets including plastic and rubber basementtanking sheet - Definitions and characteristicsEN 13969:2004+A1:2006Flexible sheets for waterproofing - Bitumen damp proofsheets including bitumen basement tanking sheets - Defi-nitions and characteristics
EN 13970:2004+A1:2006Flexible sheets for waterproofing - Bitumen water vapourcontrol layers - Definitions and characteristicsEN 13984:2013Flexible sheets for waterproofing - Plastic and rubber va-pour control layers - Definitions and characteristics
Period ofvalidity: 16.01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
- Translation - 26/29
Annex to the accreditation certificate D-PL-11267-01-01
K DAkkSDeutscheAkkreditierungsstelle
Decision / resolution of theCommission
1999/90/ECMembranes
1999/91/ECThermal insulation products
System1 1 Technical specification
EN 14891:2012+AC:2012Liquid-applied water impermeable products for use be-neath ceramic tiling bonded with adhesives - Require-ments, test methods, evaluation of conformity, classifica-tion and designation
3 EN 14909:2012Flexible sheets for waterproofing - Plastic and rubberdamp proof courses - Definitions and characteristicsEN 14967:2006Flexible sheets for waterproofing - Bitumen damp proofcourses - Definitions and characteristics
EN 13162:2012+A1:2015Thermal insulation products for buildings - Factory mademineral wool (MW) productsEN 13163:2012+A1:2015Thermal insulation products for buildings - Factory madeexpanded polystyrene (EPS) products - SpecificationEN 13164:2012+A1:2015
Thermal insulation products for buildings - Factory madeextruded polystyrene foam (XPS) products - SpecificationEN 13165:2012+A2:2016Thermal insulation products for buildings - Factory maderigid Polyurethane foam (PU) products - SpecificationEN 13166:2012+A2:2016Thermal insulation products for buildings - Factory made
g phenolic foam (PF) products - SpecificationEN 13167:2012+A1:2015Thermal insulation products for buildings - Factory madecellular glass (CG) products - SpecificationEN 13168:2012+A1:2015Thermal insulation products for buildings - Factory madewood wool (WW) products - SpecificationEN 13169:2012+A1:2015Thermal insulation products for buildings - Factory madeexpanded perlite board (EPB) products - SpecificationEN 13170:2012+A1:2015Thermal insulation products for buildings - Factory madeproducts of expanded cork (ICB) - SpecificationEN 13171:2012+A1:2015Thermal insulation products for buildings - Factory madewood fibre (WF) products - Specification
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
- Translation - 27/29
Annex to the accreditation certificate D-PL-112G7-01-01
t DAkkSDeutscheAkkreditierungsstelle
Decision / resolution of theCommission
1999/469/ECProducts related to
concrete, mortar and grout
1999/470/ECConstruction adhesives
2011/19/EUSealants for non-structural
use in joints in buildingsand pedestrian walkways
System11 Technical specification
EN 14889-1:2006Fibres for concrete - Part l: Steel fibres - Definitions, spec-ifications and conformityEN 14889-2:2006Fibres for concrete - Part 2: Polymer fibres - Definitions,specifications and conformityEN 12004:2007+A1:2012Adhesives for tiles - Requirements, evaluation of con-formity, classification and designationEN 12004-1:20072>Adhesives for tiles - Requirements, evaluation of con-formity, classification and designationEN 15651-1:2012Sealants for non-structural use in joints in buildings andpedestrian walkways - Part l: Sealants for facade ele-ments
EN 15651-2:2012Sealants for non-structural use in joints in buildings andpedestrian walkways - Part 2: Sealants for glazingEN 15651-3:2012Sealants for non-structural use in joints in buildings andpedestrian walkways - Part 3: Sealants for sanitaryjointsEN 15651-4:2012Sealants for non-structural use in joints in buildings andpedestrian walkways - Part 4: Sealants for pedestrianwalkways
1} System of assessment and verification of consistency of performance
2> Harmonization in preparation (planned System: 3)
The requirements for a testing laboratory arefulfilled according to article 43 ofthe Construction Prod-ucts Regulation. Testing methods, which are necessaryfor determining the product type and cannot beexecuted by the holder ofthe certificate, are described in the list of subcontmctors.
Without prior approval by the DAkkS German Accreditation Body, the testing laboratory body is per-mitted to use new revisions ofproduct Standards.
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
- Translation - 28/29
K DAkkS
Annex to the accreditation certificate D-PL-11267-01-01
DeutscheAkkreditierungsstelle
Abbreviations used:
ASTMDAfStb
DASt
DBV
FIPNENPAÖNORMRALRILEM
SEWSIATP Min-StB
UEAtc
American Society for Testing and MaterialsDeutscher Ausschuss für Stahlbeton, Berlin (German Committee forReinforced Concrete)Deutscher Ausschuss für Stahlbau
(German Committee for steel building)Deutscher Betonverein e. V., Wiesbaden
(German Concrete and Construction TechnologyAssociation)Federation Internationale de la Precontrainte
Nederlands Normalisatie-lnstituut
Internat test procedureAustrian Standard
RAL Deutsches Institut für Gütesicherung und Kennzeichnung e.V.Reunion Internationale des Laboratoires d'Essais
et de Recherches surles Materiaux et les Constructions
Stahl-Eisen-Werkstoffblatt des Vereins Deutscher Eisenhüttenleute
Swiss Society of Engineers and Architects (SIA)Technische Prüfvorschriften für Mineralstoffe im Straßenbau, Hrsg.von der Forschungsgesellschaft für Straßen- und Verkehrswesen, Ar-beitsgruppe Mineralstoffe im StraßenbauUnion Europenne pour l'Agrement technique dans la construction
Period ofvalidity: 16. 01. 2018 to 13. 11. 2021Date of issue: 08. 06. 2018
- Translation - 29/29