Post on 28-Oct-2020
transcript
DIRECTIONSFOR
PACHlNKd MACHINE0
SUTRA IMPORT CORP.3530 LAWSON BLVD.,
OCEANSIDE, N.Y. 11572.
Metal Frame“Played-Out” I ndicator LampMetal Frame
Protection BandDecoration for Ball SheathJackpot Holder
Jack pot Holder PlateDecoration AB a l l H o l d e r
Inside FrameG u a g e R u b b e rJackpot TrayL o c k
Name PlateP l u n g e r C o v e r
H a n d l eDecoration BF i n g e r R e s t
- - C o n t e n t s - - -When played-out indicator lamp is on, despite balls reserved When shooting apparatus does not work well. . . . . . . . . . . . . . . . . . . . . . . . . . . 4
in the reserved tank. . . . . 1 When shot balls stop at the top of the ball pick . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
When balls reserved in the tank fall down, despite balls How to switch the pestle spring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
remained in the supply apparatus. . . . . 1 When more prize balls than fixed flow out of the ball sheath.
When “RENCHAN” keeps getting clown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 (When the bluke does not bite well) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
When the handle creaks or sounds uncomfortable. . . . . . . . . . . . . . . . . . . . . 3 The position of the handle rod for the best shooting . . . . . . . . . . . . . . . 6
When balls are not filled in the ball sheath. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 W h e n b a l l s a r e i r r e g u l a r l y b o u n c e d . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
@ Outside Frame@ Sophia Key
@Chuck@ R e s e r v e B a l l P i p e@ Reserve Ball Curve@Scheduled Play-out Switch,
0 Shaft(s> Middle Tank@ Fluke preventing incompleteness
@I Lie Detector@I Shutter Rod@Tail Shoot of Safety Ball@ Counter Connection Cornice
@Counter@I Terminal
@ Upper Tank8 Ball Collect Case@ Damper Protection Cover
@ Ball Sheath(80 Protection@ Bell Pipe@ Ball-Removing Pipe
BASIC INSTRUCTIONS
There are many models of Pachinko Machines, but the under-mentioned basic
instructions are applicable to all the models.
(1 ) Put into @ Upper Tank as many balls as possible. By the action of weight
of balls contained in Upper Tank, Shutter placed inside of @ Plunger Cover
is lifted up so that ball may enter Plunger Room.
Put the balls in 8 Jackpot Holder. Now you can play.
(2) Always take care to keep @ Lie Detector in vertical position. If it is kept in
horizontal position, the prize balls don’t come out.
vertical position horizontal position
(3) To open Front Window, lift up @ Lever.
To shut, just push window in.
(4) To take out all the balls contained Upper and Middle Tanks, lift down @
Lever, and balls come out from 0 Counter Connection Cornice.
Don’t forget to lift up @ Lever to the original position after having taken
out bal Is.
(5) Keep always balls clean and not rusty.
-A
- B
l When played out indicator
lamps is on, despite balls
reserved in the reserve
tank.
0When both A parts are connected with eachother by sparkling, keep 2-3mm between those(as shown), after connection point is filed off
connection point
rust. >
(Leadifg rod)
When G gets apart, put G back to original
pos i t ion (as shown by a r row) , w i th o thermachines refered to.
(shutter rod)
When G touches H, prevent G (scheduledplay-out lever) from touching H ( reserve tank )for smoothly working.
When obstacles other than balls get into H
(reserve tank), take them out.
Clean dirts off to have G
operate smoothly.
Pr\
( schedu IeGd playout lever)
-When balls reserved in the tank fall down, despite balls remained in the supply apparatus
shaft, tighten the screw,
keeping the shaft in properlength so balls as to besupplied properly.
0 When loosel y screwedbalance weight (E) causeschange in the position of Eor E falls down, moove Eand tighten E after putting
supp l y appa ra tus (D) f o rreserve balls in the positionthat it can properly work.
supply apparatus balanceD for reserve balls iE weight
IQWhen lever’s (H) touch of apart of the middle tank (F)
causes unproper work to H,make sure that the moovingpart of the lever (H) mustnot ouch the middle tank (F)
- G transfer pipe
Hl e v e r
l When “RENCHAN” keeps
getting down.0
When the crank touches bounced ball adjuster,bend the crank in the direction of arrow (as
seen from top
shown) or v ice versa./&ggg/-~@$?@--
/ /
=+Fc r a n kP ‘i=
\ when being touched i -7-
b o u n c e d b a l l a d j u s t e r bend this part
0
When the ball sheath touches the base,
bend in the direction for adjustment.
ease
b a l l s h e a t h bracketIwhen being touched
0
When the RENCHAN cannot afford to lift up
the lie detector while the damper gets down, lie detector
bend the rod for adjustment.
$
r o d
RENCHAN lift
When the ball sheath and the crank are delayedin getting back to the original positions,
( 1 ) Clean dirt, if any, off balls by water( 2 ) Give about 0.5mm play by bending up
the bracket when there is no play on 6
and C in the direction of the axle( 3 ) Chanqe the parts for new if there is no
play on D(4) Compare the number of weight and
thickness of E with that of other
machines . If it is less, increase the weight.
0 When the handle sounds uncomfortable.
0 Loosen the plus screw (A). Tighten the screw (B) for fittingthe ho lde r .
the holder
0 Tighten the donble nuts. Change the ball bearing for new
(refer to 3 on page 7) or calk it.
ng
(double nuts)
2
l When balls are incom-
pletely supplied in the
ball sheath.
1)When bails get stuck at bail-acusstoming part,give 1mm space between the center of ball-
acusstoming part and the coupling pipe by A ball-accustomingadjusting D, or take out dirt in the couplingp i p e .
B connection pipe
0
Adjustment of incompleteness preventer. Whenmiddle tank
the incompleness preventer does not stop the Y---1movement of RENCHAN while no balls are inthe middle tank. Adjust as shown.
0
Adjustment of supplying apparatus. W h e nballs are not supplied to the middle tank,loosen E and shorten L for adjustment. Whenballs fall down too much, lengthen L. L
I&
/E J
When balls do not well flow out into the ball
sheath, twist the bracket of D for adjustingthe shaft to the proper position when theconnection pipe is not leveled with the ball
shea th . )pJaft
B A C <c o u p l i n g connection balls sheath
pipe pipe
When the shutter is not required to be closed.
When the shutter is not required to
b e c l o s e d .
/I ( l e a d i n g p l a t e )
:ch)
In case that no balls are left in
Ithe uoper tank, when the shutteris not to be closed with the
switch remained closed. _
- (shutter rod)
Nail B for conuenience sake
Lift up the leading plate of the
switch. When no balls are left
in the upper tank, the scheduledfinished-lever in the upper tank
8 makes both of the shutter rod
\,and the flange rod let down tolead A to close the switch, but
0, the shutter won’t be lowerednail down.
ifted up, firstly,Secondly, set a plier between the pestleand the handle holder to lower the handle
3
0 When more prize ballsthan fixed flow out of the
sheath.
(when fluke does not bite
well).
When the crank touches the ball adjuster at D,with the crank being moved up and down in the
position that C (fluke) is off as shown, bendthe crank at the fulcrum to remove touching.
Bball adjuster
A c r a n k
.
Too little interval between the fluke and thepin of the crank causes bad biting to the fluke.
Bend the pin upward for the proper intervalof 3mm to 4mm.
When the point of the sheath is touched.when the point of the crank is pushed upwardto the maximum, there must be 1-2mm interval,
which dan be made by bending upward theright part of the fulcrum of the crank.
When the ball pipe touches the crank at the
back due to the pipe positioned in the un-proper way, reset the ball pipe upward by 2-3mm.
c r a n k
remove touching
-The position of thehandle
position of the handle rod
for the best shooting. When the handle remains atthe original position beforeb e i n g p r e s s e d d o w n ,
for adjust-ment of (x),move the ball transfer (B)left or right for resetting. foradjustment of (y), bend theh a n d l e r o d .
0
When the handle is presseddown, change the handle rod
for proper length.
With the ball transfer pressed
lightly to the left by finger,and the handle rod moved
back and forth, make lmm
interval for adjustment bet-ween the handle rod andthe ball transfer B.
6
0 When shot balls stop at
the ball pick.0
When the top of the ball (B) touches the pipe,put the top of it downward so it won’t touchthe p ipe .
point
When both ends of the ball pick touches thepipe, adjust them to go up and down withoutt o u c h i n g t h e p i p e .
0
When the ball sheath touches the plywood
surface, adjust the fulcrum of the ball sheathnot to touch the plywood.
E ball sheathb a l l a c c u s t o m i n g
When the connection between F and B does notwork well, with balls stopped, swing the head
of nail (H) to the right first. Next, clean dirtoff the axles (B, A) for the light movementof the ball pick (B) and the fluke (A).
F
pipe
G c o n t r o l n a i l
-How to change the pestle spring.
0 How to remove it.Turn it off to the left by plier.
p e s t l e s p r i n g
0
How to set it.Turn it on to the right by plier
5
0 When the shooting appa-ratus does not work well.
When the lever is dirty, clean balls in thepassage to have the number of shooting fixed.
when lifted up, ballr o l l i n g a p p a r a t u scomes off.
b a l l r o l l i n g a p p a r a t u s
0When ba l ls ge t s tuck ,
c h a n g e t h e b a l l r o l l i n gapparatus.
When
0balls cannot be shot without the handle to be flipped down
to the maximum, adjust the handle rod. Loosen the woodenscrew (A) to have the ball trausfer (C) down.
/wball t ransfer B
level
p e s t l e- -
When a shot ball comes ahead of the pestle without the handle to be pressed down. Adjustthe handle rod in case that it is bent too much (as shown).When the ball transfer (C) gets down too much, loosen the wooden screw A for lifting C up.
wood screw A
ball transfer C
IQ When the handle comes off the ball transfer Bbend the pestle upward by hammering.
f o r b e n d i n g
l When balls are irregularlybounced.
0When the handle is too tight or heavy, hammerC parts of the handle holder (as shown byarrows) for the light handle.
s p r i n g
h a n d l e h o
0
When the pestle spring comes out too much,hammer the pestle holder B in the direction ofarrow for drawing back the point of the pestle.
0
When the double nuts are loosely screwed,screw the double nuts D firmly by pushing
the handle to the handle rest.
When the pestle spring does not hit balls rightin the center, hammer or bend the pestle orthe pestle spring for adjustment.
pestlee
MEMO
,7
1
PRI NTED IN JAPAN