Post on 25-Aug-2020
transcript
DOSING SYSTEMS FORSWIMMING POOLS
innovation > technology > future
2 water & industry > dosing systems for swimming pools
Dosing systems forSwimming pools
The quality of the water from a health, aesthetic,
and safety point of view is the main characteristic
in dealing with swimming pools. Seko has made
automatic systems for all needs and applications -
private, semi-public, and public swimming pools.
The automatic systems make it possible to analyse
the water and to suitably pilot dosing units to
maintain optimum water quality. The ease with
which the unit is calibrated and set protects the
work done by both installer and end user, in order
to provide a service that fully complies with all
relevant laws.
Our wide range of measuring and dosing systems
provides a wide range of solutions in terms of
type of measurement, dosing methods, and full
compatibility with the widest range of products
used for treating pool water.
Seko offers its services, acting as a partner that is
capable of designing and developing the solution
that best meets your needs for all swimming pool
applications.
innovation > technology > future 3
indexDomesticpoolbasic EVO 4
Single pH 5Single Redox 5Double pH/Redox 5
kontrol invikta 6
Single pH or Redox 6Double pH/Redox 6
kontol panel 02 - pH 7
Pool plus kontrol 40 (pH/Redox) 8
TmDigit Timed 9
Professionalkontrol panels (with Amperometric Cell) 10
PC (pH/Chlorine) 10PR (pH/Redox) 11CL (Chlorine) 11PRC (pH/Redox/Chlorine) 12PC-Cond (pH/Chlorine/Conductivity) 12DPR (pH/Redox) 13
teknaEVO TPR (pH/Redox) 13
kontrol panles (with Potentiostatic cell) 14pH-CL/p 14pH-Redox-CL/p 14
CL-Sensor probes 15
photometer systems (pH/Chlorine DPD/Redox/Temp.) 16
hand held measuring instruments 18
measure instruments 21kontrol 40 (pH/Redox/Conductivity) 21kontrol 500 (pH/Redox/Chlorine/O2/Turbidity/Conductivity) 21
probes and accessories 22
dosing unit and accessories 24invikta 24 dynamik time 24peristaltic pump 25 tekna EVO 25spring series 25 kompact AXL-DPG 26filters 26 stirrers 27tanks 27 suction plungers 27
4 water & industry > dosing systems for swimming pools
seko group has developed a simple and reliable system made up of anindustrial container that houses the dosing pumps and instruments thusmaking installation and maintenance easy. Application of peristaltictechnology - low noise output, easy to use, low maintenance, protectionagainst siphoning phenomena, avoidance of direct contact with chemicalproducts.
poolbasic EVO
General features
• Level probe input
• Flow sensor input
• Flow signal input (at 230 V voltage for connection to
circulation pump)
• PT100 temperature sensor input (optional sensor)
• Relay control for indicating when the dosing pump is
working (230 V contacts)
• End product level alarm
• Pump on “HOLD” for calibration or alarm status
• OFA (Over Feed Alarm) on the dosing cycle
Plastic containerwith IP 65 protection level
LED Display(pH and Redox version)
DIGITAL Display(Double version)
Transaxle TechnologyProvides added support and stability to the gear shaft. This equalizes rollerpressure, extending the life of the motor gearbox and squeeze tube.
Protectionagainst unauthorised interference
Electrodeself-calibrating and quality control
Immediate set-point reading
Simply and fastSet Point programming and regulation
Power Supply230 Vac (115 Vac upon request)
Automatic proportional dosing
innovation > technology > future 5
Pool Basic Evo pH • • • • • •
Pool Basic Evo Redox • • • • • •
Pool Basic Evo Double • • • • • • • •
InstallationKit
pH Redox
690 750480
510540
570600
630660 720 A
660690
720750
780810
840 900 B870 930
� Flow Rate1.5 lt/h o 5 lt/h
� Backpressure1.5 bar
� pH measuring scale setting0...14
� Redox measuring scale setting0...1000 mV
� Flow Rate 1.5 lt/h o 5 lt/h
� Backpressure 1.5 bar
� Redox measuring scale setting (A and B)
� Flow Rate 1.5 lt/h o 5 lt/h
� Backpressure 1.5 bar
� pH measuring scale setting 6.2 ... 8.0
Double (ph/Redox)
6 water & industry > dosing systems for swimming pools
kontrolinvikta
It is an easy to use dosing system composed of a control instrument and a solenoid dosing pump.
This system is the right solution to control pH or Redox (ORP) in those applications were isrequired to dose up to 5 bars pressure.
kontrol invikta double
kontrol invikta single
Installation Kit
• User-friendly display and keyboard interface for easy programming
• Password protection for programming menu
• Relay ouput for remote alarm
• FWM (Frequency Width Modulation) proportional dosing
Technical specificationsPower supply 50/60 Hz 100÷240 VAC
Consumption 12 W or 18 W
Pump flow rate 5 lt/h
Maximum back-pressure 5 bar
pH range 0 ÷ 14.0 pH
Redox range 0 ÷ +1000 mV
Reading precision ± 0,1 pH; ± 10 mV
Accuracy ±0,02 pH; ± 3 mV
Electrode calibration Automatic
innovation > technology > future 7
kontrolpanel O2
Kontrol pH-Ox (O2) is the seko solution to Swimming pool Water Treatment withactive Oxigen.
The system incorporates the measurement and the dosing all in one small dimensions panel,supplied with all accessories for an easy, safe and fast installation.
The Oxygen control is done with theOX500 control instrument (andrelated oxygen sensor) that drives asolenoid dosing pump Invikta
series rated 5 lt/h at 5 bar to dosehydrogen peroxide.
Typical dissolved oxygen value for acorrect desinfection is 15ppm.
The pH is controlled by aPR40 control instrument(with related pH probe) thatdrives a solenoid dosing pumpInvikta series rated 5 lt/h at5 bar to dose an acid chemical.Technical specifications
Power supply 50/60 Hz 100÷240 VAC
Consumption 60 W
Pump flow rate 5 lt/h
Maximum back-pressure 5 bar
pH range 0 ÷ 14.0 pH
Oxygen range 0 ÷ 20.0 ppm
Reading precision ± 0,1 pH; ± 0,1 ppm
Accuracy ±0,02 pH; ± 0,1 ppm
Electrode calibration Automatic
Both instruments areequipped withfunctions forproportional dosing,electrodes qualitycontrol and easy andfast comprehensionprogramming menus.
kontrol40 pH0 ÷ 14.0 pH
kontrol500 pH0 ÷ 20.0 ppm
invikta5 lt/h 5 bar probe holder
8 water & industry > dosing systems for swimming pools
The POOL PLUS range is made up of three differ-ent systems, designed and built with particularattention being given to needs expressed byclients, and able to measure and control pH andRedox levels under any operating condition.
Pool Plus
pH measurement scale 0...14.00 pH
Redox measurement scale 0...1500 mV
Alarm kit standard
Direct connection of pumps
0/4…20 mA outputfor transmitting measurements
POOL PLUS
pH measurement scale 0...14.00 pH
Redox measurement scale 0...1500 mV
Alarm kit opzionale
Direct connection of pumps
Manual calibration of instruments
Pump pause for level or flow alarm
POOL PLUS P
• Simple to install.
• Plastic container with degree of protection IP 55
• Electrical connections on internal terminal board
• Power supply 230 Vac 115 Vac (upon request) at50 - 60 Hz
• Switch to pause pump
• Main switch for the system
• Remote alarm cut-out switch (only with alarm kit)
• LCD display
• pH-20 instrument for measuring and controllingthe pH
• MV-20 instrument for measuring and controllingRedox
• Precision multi-turn regulation trimmer
• Two programmable set points (pump and alarmsetting)
Pool Plus
Pool Plus P
Main switch for thesystem
LCD measurementdisplay
Visual alarm
Installation kit
Built-in dosing system, easy to maintain
innovation > technology > future 9
The TM series of dosing systems use simple analogue or digital programmers to provide effective, economical timed dosing of
chemical products.
TmDigit
Power supply: 230 Vac (115 Vac upon request)
Power rating: 5 W
Overall dimensions: 155 x 213 x 110 mm
0,4 lt/h - 1,5 ba
• IP 55 Protection level
• Simplicity of installation, use and maintenance
• Integrated Peristaltic Pump
• Digital or analogue time programmer
• Low noise output
Analogue ProgrammerThe analogue version can be used for programming dailyevents, and it is also possible to set operating time easily, usingthe internal circuit.
Digital ProgrammerUp to a maximum of 8 events can be programmed for the sys-tem for each day of the week. The programmer also makes itpossible to activate the dosing pump manually or to deactivateits activation.
Digital orAnalogue timer
systemEasy Maintenance of Peristaltic Pump Simplicity of installation
The kontrol series of panels are compact and easy to use and include all the accessories required for immediate installation (buffer
solutions for calibrating pH and Rx, and DPD colour system for Chlorine calibration).
kontrol panels with Amperometric Cell
• Self-calibration of all measurements
• Compact probe holders, complete with flow sensor,flow rate regulating valve and tap for bleeding theliquid.
• Alarm signal to indicate that the water is notflowing,
• Instruments with IP 65 protection level.
• Alarm relay (5 A – 250 Vac)
• 4÷20 mA outputs for each parameter measured, withprovision for selecting the interval
• Power supply 230 Vac (standard) or 115 Vac (upon
request)
• Programmable set points and alarm
• Pump pause function during calibration
• Temperature reading and temperature offset
(automatic with optional PT100 probe)
• Adjustments on set point: On/Off, pause/run,
proportional by impulse
kontrol PC
(pH/Free Chlorine)Panel for measuring and setting the pH value and Chlorineconcentration.
PC95 Instrument - pH 0 ÷ 14.0 / Chlorine 0 ÷ 5.0 ppm
Self-cleaning (Pt-Cu) amperometric cell
Self-calibration in relation to the physical-chemicalcharacteristics of the water to be measure
pH probe
Self-calibration with quality control of the probe
Solenoid valve to shut off the flow of water for self-calibration
Mechanical filter at water intake
Available upon request the version for high conductivity(example water of sea)
Compactplumbing
Visibleelectronic box
Easyto assemble
10 water & industry > dosing systems for swimming pools
innovation > technology > future 11
kontrol PR
(pH/Redox)Panel for measuring and setting the pH value and Redoxpotential (ORP).
PR95 Instrument - pH 0 ÷ 14.0 / Redox 0 ÷ 1000 mV
Redox (ORP) probe
pH probe
Self-calibration with quality control of the probe
Mechanical filter at water intake
Compactplumbing
Visibleelectronic box
Easyto assemble
kontrol CL
(Free Chlorine)Panel for measuring and setting the Chlorine concentration.
CL95 Instrument - Chlorine 0 ÷ 5.0 ppm
Self-cleaning (Pt-Cu) amperometric cell
Self-calibration in relation to the physical-chemicalcharacteristics of the water to be measured
Solenoid valve to shut off the flow of water for self-calibration.
Compactplumbing
Visibleelectronic box
Easyto assemble
Compactplumbing
Visibleelectronic box
Easyto assemble
kontrol PC-Cond
(pH/Chlorine/Conductivity)Panel for measuring and setting the pH value, conductivity (mS)and Chlorine concentration
PC95 Instrument - pH 0 ÷ 14.0 / Chlorine 0 ÷ 5.0 ppm
CD75 Instrument - Conductivity 0 ÷ 20000 µS
Self-cleaning (Pt-Cu) amperometric cell
Self-calibration in relation to the physical-chemicalcharacteristics of the water to be measured
pH probe
K1 conductivity probe
Compactplumbing
Visibleelectronic box
Easyto assemble
12 water & industry > dosing systems for swimming pools
kontrol PRC(pH/Redox/Free Chlorine)Panel for measuring and setting the pH value, Redox potential(ORP), and Chlorine concentration.
PC95 Instrument - pH 0 ÷ 14.0 / Chlorine 0 ÷ 5.0 ppm
PR75 Instrument - Redox 0 ÷ 1000 mV
Self-cleaning (Pt-Cu) amperometric cel
Self-calibration in relation to the physical-chemicalcharacteristics of the water to be measured
pH probe
Redox (ORP) probe
Self-calibration with quality control of the probes
Solenoid valve to shut off the flow of water for self-calibration
Mechanical filter at water intake
Digital dosing pump with pH/Redox control meterbuilt in. • Digital interface for constant or proportional
dosing, depending on the measured pH or Rxvalue
• PT100 probe input for thermal compensation
• Repetition alarm relay
• Input On-Off for remote control
• 4÷20 mA output for measure transmission
• Controller Measure single parameterpH : 0÷14,00 pH or Redox : ±1500 mV
ModelCode
20 18
2.53
1200,350,41
4 / 6 asp.4 / 7 mand.
12,0600121082
4568
160
0,420,520,630,83
4 / 6 12,2603
121051
7101518
320
0,360,520,780,94
4 / 6 23,9800
5421
20254054
300
1,111,392,22
3
8 / 12 22,2803
teknaEVO TPR
proportional dosage
CAL
ESCstartstop
PROGmodeenter
Alarm
kontrol DPR(pH/Redox)Panel for measuring and setting the pH value and Redoxpotential (ORP)
Dosing pump with built-in Tekna DPH instrumentpH 0 ÷ 14.0
Dosing pump with built-in Tekna DRX instrumentRedox ± 1500 mV
Redox probe
pH probe
Self-calibration with quality control of the probes
Mechanical filter at water intake
Probe holder complete with sensor and flow regulator
Compactplumbing
Visibleelectronic box
Easyto assemble
innovation > technology > future 13
Pressure[bar]
Flow rate[lt/h]
Fequency max[stroke./min]
Stroke capacity[cc/stroke]
Ø ConnectionsIN / OUT [mm]
Consumption[W]
Pre-Assembled panel for pH, Redox and Chlorine control.
kontrol panels with Potentiostatic cell
• Self-calibration of all measurements
• Compact probe holders, complete with flow sensor,flow rate regulating valve and tap for bleeding theliquid.
• Alarm signal to indicate that the water is not flowing,
• Instruments with IP 65 protection level
• Alarm relay (5 A – 250 Vac)
• Power supply 100÷240 VAC
• 4÷20 mA outputs for each parameter measured, withprovision for selecting the interval
• Programmable set points and alarm
• Pump pause function during calibration
• Temperature reading and temperature offset(automatic with optional PT100/NTC probe)
• Adjustments on set point: On/Off, pause/run,proportional by impulse
kontrol pH-CL/p
(pH/Free Chlorine)It is composed of one PR40 for pH control and oneCL500 for chlorine control with pH probe, probe holderand connection box.
Measurement range:0÷14 pH; 0÷10 ppm Free Chlorine
kontrol pH-Redox-CL/p
(pH/Redox/Free Chlorine)It is composed two PR40, for pH and ORP control, and oneCL500, for chlorine control, pH and ORP probes, probes-holder andconnection box.
Measurement range:0÷14 pH; 0÷10 ppm Free Chlorine; 0÷1000 mV Redox
kontrol pH-Redox-CL/p
kontrol pH-CL/p
14 water & industry > dosing systems for swimming pools
innovation > technology > future 15
CL-Sensor probePSS-PR-CL-S probe holder
F-CL-1 F-CL-2 F-CL-3 T-CL D-CL
Measurement 0÷10 ppm 0÷10 ppm 0÷10 ppm 0÷10 ppm 0÷10 ppm
Resolution ±0.01 ppm ±0.01 ppm ±0.01 ppm ±0.01 ppm ±0.01 ppm
pH Scale 4÷8 pH 4÷12 pH 4÷11 pH 0÷14 pH 0÷14 pH
Flow(*) >=30 lt/h >=30 lt/h >=30 lt/h >=30 lt/h >=30 lt/h
Temperature 45°C 45°C 45°C 45°C 45°C
Pressure 1 Bar 0,5 Bar 0,5 Bar 0,5 Bar 1 Bar
Power supply 12÷30 Vdc 12÷30 Vdc 12÷30 Vdc 12÷30 Vdc 12÷30 Vdc
Output signal 4÷20 mA(**) 4÷20 mA(**) 4÷20 mA(**) 4÷20 mA(**) 4÷20 mA(**)
Diameter 25 mm 25 mm 25 mm 25 mm 25 mm
Length 225 mm 225 mm 225 mm 225 mm 225 mm
Body material PVC PVC PVC PVC PVC
Membrane M20 M48 M48G M48 M20
Electrolyte ECL1 ECC1 ECS1/Gel ECP1/Gel ECD4
Cable Max. 15 meters Max. 15 meters Max. 15 meters Max. 15 meters Max. 15 meters
Treatment Free chlorine Organic free chlorine Free chlorine Total Chlorine Chlorine Dioxidetype Inorganic (Chloroisocyanurate) Inorganic (Inorganic or Organic)
(*) Stabilization time average 15 minutes, maximum 1 hour (**) Output of current signal proportional to the measurement
CL-Sensor ProbeThis range consists of potentiostatic amperometric probes to measure free or total chlorine forapplications such as: water treatment, swimming pools, industrial applications and more.
The wide range of probes allows a better choice depending on the parameter to be tested, thus obtaininga more accurate measurement.
• The two-wire interface allows quick and easy installation
• Calibration of the probe is guided by the kontrol CL500 instrument
16 water & industry > dosing systems for swimming pools
photometersystemMulti-Parameter Control Unit for contemporarydetermination of Free Chlorine (PhotometricSystem), pH, Redox and Temperature.
The system is equipped with a graphic displaysubdivided into areas for simultaneous display ofall available measurements.
The removable cover guarantees the accessibilityof the system and also allows:
� Protection of the chemical reagents fromultraviolet rays
� High visibility display
� IP65 container protects from humid environments
� Multilanguage user-friendly interface. The wide displayallows the creation of graphics for each available measurement viaan internal Data Logger function.
� Mechanics with “flipdoor” permitting easyaccess to the electricalconnections
� BNC connectors on side of boxfacilitate quick maintenance ofthe pH and Redox probes
The peristaltic pump, whichhas 4 pressure points, saveson reagents
Continous monitoring ofreagents using level probes
The DPD reagent in powderform (to be diluted beforeuse) is an excellent solutionfor safe storage
innovation > technology > future 17
Technical FeaturesFree or Total Chlorine Measurement 0÷ 5 ppm Resolution 0,01 ppm Precision 1% FS
pH Measurement 0÷14 pH Resolution 0,01 pH Precision 1% FS
Redox Measurement ±1500 mV Resolution 1 mV Precision 1% FS
Temperature Measurement 0÷50 °C (32 ÷ 106 °F) Resolution 0.1°C (.18 °F) Precision 1% FS
Display 240x128 pixel backlit graphic
Programming Via keypad with 4 bubble keys
Digital Input Dry contact for disabling dosages
Analogue Input 0/4÷20 mA for auxiliary measurements
Power supply 90÷264Vac 50-60Hz 66 Watt
Internal Data Logger Flash Memory 16000 records Recording interval 00:00 ÷ 99:99 minutesType circular / refill Tabular / graphic display
4 Analogue Outputs Size Chlorine, pH, Redox, TemperatureType 0/4÷20 mA galvanically isolatedLower / upper / inversion limit programming Maximum load 500 Ohms
4 Set Point Relay Outputs nr. 2 for chlorine measurement + nr. 2 for pH measurement Max. relay load 3A (resistive) 230Vac
Alarm Relay Output Lack of sample waterReagents run outFloodlight burned outDirty cell Relay max. resistive load 3A at 230Vac
2 Auxiliary Relay Outputs Programmable as Set Points for Redox measurement, Set Points for Temperaturemeasurement, Timed activation for cell cleaningRelay max. resistive load 3A at 230Vac
Serial Port Output (RS485) RTU MODBUS protocol with programmable Baud rate 1200 ÷ 38400
� Hydraulics with outlet of water containing reagents forchlorine measurement. This allows a considerable reduction inthe quantity of water used for the measurement. The water usedfor checking the pH and Redox can be channelled towards thebuffer tank, while only the water polluted by the DPD reagents willbe drained off and managed separately in accordance with localregulations
� Installation time reduced due to quick-coupling connectionsfor sampling and outlet pipes
� The unit has self-calibration for optical unit and ensures a highaccurancy of Chlorine measurement precision using a 520nm sensor and light source emitted by a LED
Probe holder
Clean water inlet
Special Outlet forwaste water withDPD reagent
Clean wateroutlet
Available version Total Chlorine + Temperature
Free Chlorine + Temperature
Free Chlorine+ pH + Temperature
Free Chlorine + pH + Redox + Temperature
18 water & industry > dosing systems for swimming pools
PO-TPocket instrument which allows a rapid and trustablemeasurement. Supplied with crash proof box with probeincluded.
These easy to use, extremely practical instruments are the latest generation of hand heldinstruments.
Practical waterproofsupport
Batteries easy toreplace
Sensor easy to replace
Tester
PO-T Rx Redox range : 0 ÷ 1999 mV
PO-T Rx Waterproof Redox range : 0 ÷ 1999 mV
PO-T pH pH range : 0 ÷ 14,00 pH
PO-T pH Waterproof pH range : 0 ÷ 14,00 pH
PO-T pH Waterproofwith replaceable probe pH range : 0 ÷ 14,00 pH
PO-T CD2 Conductivity range : 0 ÷ 2 mS
PO-T CD2 Waterproof Conductivity range : 0 ÷ 2 mS
PO-T CD2 Waterproofwith replaceable probe Conductivity range : 0 ÷ 2 mS
PO-T CD20 Conductivity range : 0 ÷ 20 mS
PO-T CD20 Waterproof Conductivity range : 0 ÷ 20 mS
PO-T CD20 Waterproofwith replaceable probe Conductivity range : 0 ÷ 20 mS
Waterproof
Standard
pH-Temp Tester Large, double reading, LCD display.
Temperature measurement range:0-50°C or 32,0-122,0°F(accuracy 0,5°C or 0.9°F).
Measurements from -1.00 to 15,00 pH(accuracy ±00,1 pH)
ORP Tester (Redox)Measurements from–999 mV to 1000 mV(accuracy ± 2 mV).
Cond Tester Doble conductivity measurements rangefrom 0 to 1990 µS/cm (accuracy ± 1% of full scale)from 0 to 19.90 mS/cm (accuracy ± 1% of full scale)
Battery lifespan: more than 150 hours
pH TesterMeasurements from -1.00 to 15,00 pH(accuracy ±00,1 pH)
• Large LCD display
• Sensor and batteries easy to replace
• Easy to use
• Impermeable to water
• Self switch-off after 8,5 minutes
• Battery charge indicator
• Battery lifespan: more than 500 hours
• Operation temperature: 0 to 50 °C
• Measurement from –1,0 to 15,0 pH(accuracy ± 0,1 pH)
innovation > technology > future 19
- pH measurements from 0,00 to 14,00 (accuracy ±00,1 pH)- Redox measurement ± 1000 mV (accuracy ± 2 mV). - Temperature measurement from 0,0 to 100 °C (accuracy ± 0,5 °C)- Automatic / manual temperature offset (0 – 100°C).
pH-ORP6 Series- Measurements 0-20.00, 200.0, 2000 mS/cm (accuracy ± 1% of full scale)- Measurements 0-20.00, 200.0 mS/cm (accuracy ± 1% of full scale)- Temperature measurement from –10,0 to 110,0 °C (accuracy ± 0,5 °C)- Automatic / manual temperature offset (0 – 50°C).
Con6 Series
- Measurements 0 – 10,00, 10.0 – 100,0, 100 – 1000 ppm (accuracy ± 1% of full scale) - Measurements 1,00 – 10,00, 10,0 – 100,0, 100 – 200 ppt (accuracy ± 1% of full scale)- Temperature measurement from – 10,0 to 110,0 °C (accuracy ± 0,5 °C)- Automatic / manual temperature offset (0 – 50°C).
Ox6 Series- pH simulation values 1.00, 1.68, 4.01, 6.86, 7.00, 9.18, 10.01, 12.45
(accuracy ± 0,02 pH)- Redox simulation values –1800, -900, -390, +390, +900, +1800 mV
(accuracy ±1 mV)- Operation temperature: 0 to 40 °C
pH-Redox signal simulator
Series 6
Practicalcontainer
Protectivecasing
Waterproofkeyboard
20 water & industry > dosing systems for swimming pools
- Measurement of the concentration of free Cl, total Cl, cyanic acid, and pH
- Impermeable to water
- Free and total Cl measurements: 0 – 1,99 and 2,0 – 6,0 ppm (accuracy ± 00,2or ± 0,2 ppm)
- Cyanic acid measurement 5 – 90 ppm (accuracy ± 4 ppm)
- pH measurement 5,9 – 8,2 (accuracy 0,1 pH)
- Operation temperature: 0 to 50 °C
- Battery charge indicator
- Battery type “AAA” (x4).
- Battery lifespan: more than 3000 tests
C401 Portable Photometric Measuring Instrument
- Impermeable to water
- Self-selection of measuring interval 0,01 – 19,99, 20,0 – 99,9, 100 – 1000 NTU(accuracy ± 2% of the reading)
- Operation temperature: 0 to 50 °C
- Battery charge indicator
- Battery type “AAA” (x4).
- Battery lifespan: more than 1200 tests
- Light lifespan: more than 1,000,000 tests
T101 portable turbidity measuring devices
Chlorine from 0,1 to 5.00 mg/ltpH from 6.8 to 8.4Bromine from 0,1 to 9.9 mg/ltAlkalinity from 10 to 500 mg/ltCyanuric Acid from 0 to 200 mg/lt
Power Supply 1 x PP3 Battery (not included)
Size : 17.5 x 7.5 x 4.5 cm
Weight : 132 gr
SP163 Cool Pooltester Cl/pH/Alk
SP164 Cool Pooltester Cl/pH/Cyn
SP165 Cool Pooltester Cl/pH/Br
SP166 Cool Pooltester Br/pH/Alk
AR 165/1 Refil for Cl/pH/Alk
AR 165/2 Refil for Cl/pH/Cyn
AR 165/3 Refil for Cl/pH/Br
AR 165/4 Refil for Br/pH/Alk
PT 164 Box of 5 sapres test tubes
Cool Pooltester Portable Photometric Measuring Instrument
PracticalcontainerWaterproof
keyboard
Batterieseasy toreplace
innovation > technology > future 21
Wall-mounting version with IP65degree protection (144x144x90 mm)
kontrol40• Multilinguage menu
• Password protectionof menu setting
• Relay status indicator
• Manual control of all instrumentfunctions
• Measurement probes quality control
• OFA (Over Feed Alarm): timed excessdosage alarm
• Alarm band can be set with min. andmax. values
• Proportional dosing through Set Points
• Galvanic isolation for output 4 to20 mA
• Power supply 100÷240 Vac
kontrol PR40Range 0÷14 pH or ±1500 mV
kontrol CD40Range 0÷50000 µS
DIN Rail Version (6 EN50022 modules)
Panel-mounting version(48x96x100 mm) Panel-mounting version
(96x96x92 mm)
kontrol500
Wall - or pole-mounting version withIP65 degree protection (144x144 mm)
Panel-mounting version (96x96 mm)
• Graphic Display128x64 pixel
• PID control functions
• Serial communication portby RS485
• Quality probes ofmeasurement probes
• Power supply 100÷240 Vac
kontrolPR500Range 0÷14 pH or ±1500 mV
kontrolCD500Range 0÷20000 µS
kontrolCL500Range 0÷20 ppm Free Chlorine
kontrolOX500Range 0÷20 ppm Oxygen
kontrolTB500Range 0÷100 FTU / NTU [Turbidity]
Mounted on a pole with abracket and shelter(accessories)
22 water & industry > dosing systems for swimming pools
PT-100 temperature sensor
PT-100-V 0- 100 °C 2 Bar Glass casing 12 mm Ø length 120 mm 3-core cable 5 m long
PT-100-NUT 0- 100 °C 6 Bar PVC casing 1/2 gas 2-core cable 1 m long
PROBES
pHSPH-1-S-6 0... 14 pH 50 µS 60 °C 7 bar 1 Standard GEL Cable 6m+BNC Standard Ø 12 Epoxy 12x120
SPH-1-S-1,5 0... 14 pH 50 µS 60 °C 7 bar 1 Standard GEL Cable 1,5m+BNC Standard Ø 12 Epoxy 12x120
SPH-3-WW 2... 14 pH 5 µS 80 °C 6 bar Open hole GEL S7 PG 13,5 Glass 12x120
RedoxSRH-1PT 6 ±2000 mV - 60 °C 7 bar 1 Standard GEL Cable 6m+BNC Standard Ø 12 Epoxy 12x120
SRH-1PT 1,5 ±2000 mV - 60 °C 7 bar 1 Standard GEL Cable 1,5m+BNC Standard Ø 12 Epoxy 12x120
SRH-3-PT ±1000 mV - 80 °C 6 bar Open hole GEL S7 PG 13,5 Glass 12x120
Elec
trod
ety
pe
Mea
sure
men
tra
nge
Min
imum
cond
uctiv
ity
Max
imum
tem
pera
ture
Max
.pr
essu
re
Poro
us
sept
um
Refe
renc
e
Conn
ectio
n
Proc
ess
asse
m-
bly
Casi
ng
AISI 304 ElectrodeElimination of parasitic currents. Mechanical connection Standard Ø 12 mm
pH Redox
PT-100-V PT-100-NUT
Standard Boot BNC
Standard Boot BNC
innovation > technology > future 23
Model Value Quantity
KIT ST 4-7 pH, 465 mV 20 °C 90 ml
ST-PH-4 4,00 pH 20 °C 250 ml
ST-PH-7 7,00 pH 20 °C 250 ml
ST-RX-465 465 mV 25 °C 250 ml
BUFFER SOLUTIONS
CABLES
ELECTRODE HOLDER
Cables for connecting electrodes to the S7 head
CE-5-B screened cable with S7 and BNC soldered connectors, 5 m long
CE-10-B screened cable with S7 and BNC soldered connectors, 10 m long
Model Description N° Electrodes Temp. max Maximum Time
PSS 7 - SIngle transparent glass 1 40 °C 6 bar
PSS 7 transparent glass 3 40 °C 6 bar
Model Description Max. Temperature Max. pressure Process connection Electrode connection
PSS 3 PVC 60 °C 7 bar 1/2” G.M. Ø 12 mm
PSS-PG PVC 60 °C 7 bar 1/2” G.M. P.G. 13,5 mm
PSS7PSS7Single PSS3 PSS PG
KIT
250 ml
24 water & industry > dosing systems for swimming pools
GeneralFeatures
Power Supply100÷240 Vac
External trigger24÷240 Vac
Digital Display
Priming (MOM), Run (ON),Stand-by (OFF) modeselectable by switch
Flow rate 4, 2 and 1 lt/h @ 1,5 Bar (selectable byprogramming menu)
invikta It is made up of a simple, reliable, electromagnetic dosing pump, based on amicroprocessor.
The outer PP plasticcontainer has an IP65protection level andprotects the unit fromwater spray and canwithstand aggressiveenvironments
Wall mounting: • directly on the
wall• fixing bracket kit
Pump casingwith manual
priming valve
Standard power supply90÷265 Vac(20÷90 Vac upon request)
The pump has an input forthe level probe
Manual regulation of theflow rate from 0 (pumpstopped) to 100% ofmaximum flow rate
Operating status LED: • Flashes when the pump is
operating• Flashes slowly when the
pump is stopped• Flashes quickly when a
level alarm is activated
dynamik time Peristaltic pump with timed dosing by external trigger.
Adjustableflow rate anddosing timeby keyboard
IP65 Enclosure
Wall mountingbracket
TransaxleTechnology
Easy and safeinlet-outlet tubingconnection
External triggerinput
Power supply100÷240 Vac
Switch for Priming, Runand Stand-by modeselection
innovation > technology > future 25
Peristaltic pump technology means low maintenance, lownoise output, and that no valves are used at all.
MODELS:PE-1,5.1,5 1,5 lt/h (constant flow rate) at 1,5 max
PE-1,5.05 5 lt/h (constant flow rate) at 1,5 max
PR4 4 lt/h (adjustable flow rate) at 1,5 bar
SPRING Series
Electromechanical Dosing Pumps
Dosing pumps with spring return mechanism. Version with plunging piston or mechanical membrane.
MODELS:Serie PS1:max flow rate 304 lt/h max pressure 20 barSerie PS2max flow rate 1000 lt/h max pressure 20 barSerie MS1max flow rate 460 lt/h max pressure 10 barSerie MS0max flow rate 47 lt/h max pressure 5 bar
tekna EVOSolenoid Dosing Pumps
• 4 models that cover 1 to 60 lt/h with an output pressure upto 20 Bar
• Full chemical compatibility
• Reduced maintenance
• Dosing performance always stable
• Version available:
- Analogue and digital interface.
- Constant Flow Rate with timer control or adjustable by knob
- Proportional Flow Rate according to an external analogue ordigital pulse signal
- Many additional functions
PERISTALTIC Pump
26 water & industry > dosing systems for swimming pools
Panels with 2 dosing pumps and electric wiring box, particular-ly suitable for installing with Kontrol series panels.
KOMPACT AXL-DPG
Housings and filter cartridgesHOUSINGS FOR FILTER CARTRIDGES MINOR 5” SERIESOperating conditionsMaximum pressure: 8 barMinimum temperature: 2 °CMaximum temperature: 40 °C
CharacteristicsNon-toxic materialsHead: Loaded polypropyleneIN/OUT threaded inserts: BrassCup: SAN and White loaded polypropyleneO-Ring: NBRFlow rate: 120 lt/minLifetime test: 200,000 cycles from 0 to 10 bar
FILTER CARTRIDGES RLN SERIESAverage lifetime: Variable, maximum 24 monthsMaintenance: Wash every 3 monthsOperating conditionsMaximum temperature: 40 °C
CharacteristicsNon-toxic materialsFiltering material: Nylon (polyamide)External support: PolypropyleneCaps: PolypropyleneSeals: EPDM
FILTERS
Easyto assemble
Compatiblewith chemicalproducts
Easyto assemble
PUMPPUMPPUMPPUMPPUMPPUMP
CLCLCL PHPHPH SUPPLYSUPPLYSUPPLY
POWERPOWERPOWERALARMALARMALARM
FF FF
NN NN
RELE'RELE'RELE' RELE'RELE'RELE'
Kompact AXL- N° 2 Tekna AXL analogue dosing pumps
for continuous operation (available in602 or 902 versions)
- Electric wiring box
mAmAmAmAmAmA
FREQ.FREQ.FREQ.
INPUT PUMP 1INPUT PUMP 1INPUT PUMP 1
--++
POWERPOWERPOWER
SUPPLYSUPPLYSUPPLYINPUT PUMP 2INPUT PUMP 2INPUT PUMP 2
++
mAmAmA
++-- FREQ.FREQ.FREQ. mAmAmA
++
-- ++ ++--
Kompact DPG- N° 2 Tekna DPG digital dosing pumps
for proportional operation (availablein 602 or 902 versions)
- Electric wiring box
innovation > technology > future 27
Electrical stirrers with three-phase motor (single-phase upon request), and fixing flange. Specifically made for fitting on SER series tanks.Materials in contact with the liquid:non-toxic PVC or AISI 316. Speed:1400 or 70 rpm.
Slow 70 rpm • Fast 1400 rpm
600 mm
800 mm
900 mm
1100 mm
Specifically designed for assembling along with bothelectromechanical and electromagnetic dosing unitswith stirrers and dosing pumps. Made using a centrifugalpurpose, the mechanical strength of these tanks isguaranteed. Made of food-grade polyethylene, thesetanks are compatible with almost all chemical productsused in dosing systems.
TANKS
Designed and built for easy, immediate use, they
ensure regular operation of the..They are all fitted with
foot filter and are available inversions that have built-
in level probe to indicate when the chemical product is
finished in order to prevent vacuum dosing that would
damage the pump.
SUCTION PLUNGERS
STIRRERS
Model Height (cm) Diameter (cm)50 45,5 40
100 64 46
250 87 59.5
300 95 67
500 118,5 76
1000 122 108,5
Heights (mm) Model tanks450 Ser50
650 Ser100
900 Ser250
1050 Ser300
1250 Ser500/1000
www.seko.com
SEKO Asia Pacific SINGAPORE • SEKO China CHINA • SEKO do Brasil BRAZIL • SEKO DosingSystems USA • SEKO Deutschland GERMANY • SEKO France FRANCE • SEKO Iberica SPAINSEKO Italia ITALY • OOO SEKO RUSSIA • SEKO Northern Europe DENMARK • SEKO SIETAROMANIA • SEKO Southern Africa SOUTH AFRICA • SEKO UK UNITED KINGDOM
BRO SWPUK 081The technical data may be modified without notice. The drawings and images are only indicative