Post on 10-Feb-2017
transcript
Drives, motors and mechanical power transmission catalogue 2014
2 ABB drives and motors quickfinder l ABB drives and motors catalogue 2014
ABB drives and motors quickfinderSelect a drive or motor using the quick criteria below
Supply voltage
110-
120V
1ph
200-
240V
1p
h
208-
240V
3ph
380-
480V
3ph
380-
415V
3ph
500V
3p
h
690V
3p
h
Motor power kW IP rating Motor family Motor type
Medium voltage AC drives
Low voltage DC drives and power quality filters
ABB motors 0.25 - 1000 IP55/56/65 ABB general performance motorsABB process performance motorsABB hazardous area motors - flameproofABB hazardous area motors - non sparkingNEMA motors
M2AA, M2BAM3AA, M3BPM3JP/KPM3GPNEMA standard
l l l l l
l l l
l l l
l l l
l l l
l
l
l l l l
l l l l
l l l l l l l l
l l l l
l l l
l l l
l l l l l
Motor power kW
0.18 - 0.37 (ACS55)0.18 - 2.2 (ACS55)0.37 - 2.2 (ACS150)0.37 - 2.2 (ACS150)0.37 - 4.0 (ACS150)
0.37 - 2.20.37 - 11.00.37 - 22.0
0.37 - 2.20.37 - 11.00.37 - 22.0
0.75 - 751.1 - 180200 - 355
0.75 - 751.1 - 180200 - 355
1.1 - 160
200 - 400
0.55 - 551.1 - 1601.5 - 2005.5 - 160
0.37 - 20090 - 1450110 - 185090 - 1900
45 - 145055 - 185045 - 2800
1.1 - 5600
0.55 - 7.50.55 - 2500.55 - 2504 - 250
250 - 1400
45 - 140045 - 130045 - 2800
0.55 - 250
315 kW- 35 MW2 MW - 72 MW
25 A - 5.2 kA
IP rating
IP20 (ACS55)
IP20 (ACS150)NEMA 1 (ACS150)
IP20NEMA 1IP66/69k
IP20NEMA 1
IP21, 54IP21, 54IP20
IP21, 54IP21, 54IP20
IP20
IP00
IP20,21,55
IP00, 21
IP21, 22, 42, 54, 54R
Various
IP21, IP55
IP20
IP21, 42, 54
Various
Various
Various
Drive type
ACS55 and ACS150
ACS355
ACS310
ACS550
ACH550
ACQ810
ACS800 - 01/11/31
ACS800 - 02/04/14
ACS800 - 07/17/37
ACS800 - the rest of the family
ACS880 - 01
ACS880 - 04
ACS880 - 07
ACS880
ACS1000 - ACS6000LCI megadrive
DCS400 - DCS600, PQF
Drive family
ABB micro drives
ABB machinery drives
ABB general purpose drives for fans and pumps
ABB general purpose drives
ABB drives for HVAC
ABB drives for water and wastewater
ABB industrial drives - wall-mounted unit 01 - 6/12-pulse diode 11 - active 4Q regenerative 31 - active low harmonic ABB industrial drives - module 02 - floor standing 04 - module for cabinets 14 - active low harmonic kits
ABB industrial drives - cabinet-built 07 - 6-pulse diode 17 - active 4Q regenerative 37 - active low harmonic
Other ABB industrial drives variants
Next generation of ABB industrial drives - wall mounted 01 - 6-pulse diode 04 - 6 pulse diode
Next generation of ABB industrial drives - cabinet drive 07 - 6/12-pulse diode
Next generation of ABB industrial drives
ABB medium voltage AC drives
ABB DC drives and power quality filters
ABB drives and motors quickfinder l ABB drives and motors catalogue 2014 3
Drives featurefinder - all the features in one table
An overview of the catalogue and ABB Authorised Value Providers
New in 2014
AC motors overview
European MEPS for low voltage motors
Useful engineering information and how to select an AC drive
Pages
Other variants of this new family, including multidives and multidrive modules.
ABB is able to provide medium voltage drives and motors to suite many applications and industry requirements. Air-cooled and water-cooled variants available, as well as integrated transformer solutions. Standard solutions up to 35 MW with modular power sections for lower mean time to repair (MTTR). LCI megadrives take the power offering to 72 MW.
ABB provides DC drive and motor packages via its dedicated DC partners. ABB also provides power quality solutions to ensure that drive installations comply to the rigours of G5/4 and G5/5.
Remote monitoring options and PC tools for drive commissioning and energy calculations.
Drive life cycle services - and ABB University training centre.
Pages4 - 56 - 78 - 9
6364
94 - 95
10 - 14
15 - 18
19 - 22
23, 2427, 28
25 - 28
29 - 32
33, 34 35, 39
40
33, 36
33, 3839, 40
41 - 42
44 - 47
48 - 49
44, 4550, 51
52 - 5556 - 57
57 - 58
59 - 61
62
The ABB drive family contains liquid-cooled modules, multidrives and multidrive modules and many more.
63 - 91
Brief description
ACS55 - Simplest variable-speed controller. No programming – set-up via DIP switches –ACS150 - Greater capability than ACS55 with simple keypad and built-in potentiometer. Simple parameter set that includes PID control. For OEMs and machine builders.
Machinery controller with safe torque-off to SIL3/PL e capable parameter set - includes eight-step sequencer. For OEMs and machine builders, especially food & beverage industry.
Dedicated drive for fans and pumps, with quadratic motor fluxing and energy optimisers to optimise fan and pump loads. For fan and pump OEMs and water & wastewater applications.
Drive equipped with EMC and harmonic filters. The extensive parameter set, vector control and high power density, allows the drive to fit most standard variable-speed drive applications.
Dedicated industry drive for HVAC applications. Industry specific HVAC functionality, such as fireman’s override are included as well as HVAC set-up macros and HVAC keypad controls. BACnet is also embedded as standard in the drive as a BMS communications protocol.
Dedicated industry drive for water and wastewater using direct torque control (DTC) motor control to optimise control and energy use. Safe torque-off to SIL3 means no contactors.
Drives are order based expert drives for highly demanding industrial applications. DTC motor control ensures peak performance. Wall-mounted variants are available, with differing rectifier technologies and built-in options.
Modules are drives that are optimised for cabinet installation by system integrators. The routing of cables from top in to bottom out, and the position of options and DC feeding have all been considered for optimal cost effective cabinet integration.
Cabinet drives are designed, built and tested at the factory and can be ordered with a large range of standard options. Door furniture, motor protection and various cooling variants are possible.
Next generation of the ACS800 range. New keypad, PC tools and innovations in usablity and hardware design. New PC tools and enhanced motor control complete the package.
Wheeled drive modules optimised for cabinets.
Next generation of the ABB industrial drives cabinet drive. Cabinet drives are designed, built and tested at the factory and can be ordered with a large range of standard options. Door furniture, motor protection and various cooling variants are possible.
Why choose this product?
ACS55 - Allows users of direct-on-line (DOL) starting methods to swap to variable-speed control. ACS150 - More capable parameter set allows many applications to be tackled including PID. Built-in keypad and programming in the box. Unified height and depth for easy cabinet layout. Designed for machinery applications, with assistant keypad and real-time clock. Feedback devices and fieldbus available. IP66 drives meet hygiene standards for food & beverage industry Assistant or simple keypad – dedicated pump features. Pump protection, cleaning and pipe fill features. Energy saving counters, fan PID controllers with “sleep” functionality. Assistant keypad makes it user-friendly - numerous standard software functions and macros. Real-time clock. Energy monitoring and energy optimising with everything inside.
Familiar HVAC assistant keypad matches industry expectations. Dedicated HVAC functionality and HVAC harmonic specifications make it ideal for the industry. Everything inside concept makes it easy to install and energy monitoring counters allows energy usage to be passed back over the BACnet link.
Expert control of pumping applications. Multi-pump and multi-master control. Automatic duty standby and pump cleaning and level control built-in. Drives also measure flow for built-in leak detection.
Standard rectifier, low harmonic or full regeneration can be chosen, then select from a wide range of I/O and feedback options. To complete the selection, drives can be ordered with pre-loaded industry specific software versions which allow quick integration onto winders, cranes, hoists and windmills. Suitable certification also available. Modules are fully supported with CAD databases, EPLAN libraries, with Rittal and generic kits and parts for quick cabinet installation. Cabinets are fully tested and certified EMC with thermal solutions. Extensive options available.
Drives built to order in the factory. The ACS880 is the next generation of ABB industrial drive. ACS800 is still available as the ACS880 only brings some of the variants available with the ACS800.
2014 extends the range to multidrives and drive modules.
4 ABB drives featurefinder l ABB drives and motors catalogue 2014
ABB drives featurefinder
The table highlights the differences between the various ABB drives families. It also lists some of the key features of the different ABB drives. However, the table is not exhaustive and if you are seeking a feature which does not appear in the table, please contact ABB for clarification.
l = standard m = option, internal n = option, external - = not available *= can be bookcase r = relay output, t= transistor output, or fitted or flat mounted c = configurable to be input or output,
Drive range
Voltage & power
Other rectifier options(assume 6-pulse as standard)
EMC compliance(EN 61800-3, 2004)
Harmonic filter / choke / active(EN 61000-3-4)
Enclosure class
Mechanical construction
Cooling method
Dynamic braking chopperSwitching frequencyMotor control
Programmability
Start-up assistance and helpCold configureRemovable memory moduleReal-time clockI/O built-in
( ) = via add on expansion module
+24V live control panel + commsFieldbuses
Remote monitoringSafety options(TÜV certified hardware)
ATEXPC tools
Industry specific products
Details or additional notes
12-pulse diodeLow harmonics regenerative (4Q)Low harmonics non-regenerative (2Q)Common DC link connectabilityNo EMC filter2nd unrestricted (C3)1st restricted (C2)1st unrestricted (C1)Choke (AC or DC)Swinging choke (better harmonic performance)Low harmonic (best performance)IP00IP20IP21 (or near equivalent)IP22IP42IP54/ IP54R/ IP55IP66/69KModule - panel mountable (IP20 minimum)Wall-mounted (IP21 or equiv. minimum)Free-standing, floor-standingCabinet built by ABBDirect air-coolingWater-coolingThrough panel/flange mountRange of resistors available from ABB
DTC (open/closed loop)Sensorless vectorScalar, VVVFParameter programming Adaptable programmingIEC61131 programmabilityAids to commissioning and diagnosticsProgram the drive whilst still in its box No recommissioning time neededWith assistant control panelAnalogue input/outputDigital input/outputSpeed feedback (encoder)Motor thermal protectionSTO (safe torque-off)External 24V supply can be connectedModbusFieldbus interface (popular networks)Drive-to-drive linkBACnetReport info and status remotelyEmergency stop (CAT.0, CAT.1)Safe torque-off (SIL2/PL d)Safe torque-off (SIL3/PL e)Dedicated safety moduleATEX certified for use with ABB motorsDriveConfig tool (programme in box)DriveWindow LightDriveWindowDriveAPDriveStudio (IEC 61131)Drive Composer (Entry or Pro)HVAC specificFood and beverage Machinery / OEMWater and wastewaterIndustry specific applications FW
ABB micro drives(ACS55 - p10)
(ACS150 - p12)(ACS55) 1-ph 100 - 120 V: 0.18 - 0.37 kW
1-ph 200 - 240 V: 0.18 - 2.2 kW(ACS150) 3ph 380 - 480 V, 0.37 - 4.0 kW
----
l(or remove EMC screen)l
n(ACS150)l,-(ACS150)
n
---l
m (Nema 1, ACS150)----
l* (DIN mount + screw)m (Nema 1, ACS150)
--l
--
-(ACS55), l(ACS150)4 to 16 kHz
--l
uses dip (ACS55), l(ACS150) ---l
--
1 / 03 / 1r (ACS55), 5 / 1r (ACS150)
--------------
n (ACS55), - (ACS150)------m
l
--
ABB machinery drives(ACS355 - p15)
1-ph 200 - 240 V: 0.37 - 2.2 kW3-ph 200 - 240 V: 0.37 - 11 kW3-ph 380 - 480 V: 0.37 - 22 kW
---l
l (remove EMC screw)l
n
-n
---l
m (Nema 1)---l
l* (DIN mount + screw)m (Nema 1 kit)
--l
--l
4 to 12 kHz-l
l
l
l(sequencer)-
l(assistant panel)l
-l
2 / 15 / 1r+1t+(3r)
m
m configurablel
l(MPOW)m
m
--
n(SREA)--l
-lEx tD and DIP only
-n
-----l
l
m
l(IP66/69) F&B
ABB general purpose drivesfor fans and pumps
(ACS310 - p19)1-ph 200 - 240 V: 0.37 - 2.2 kW3-ph 200 - 240 V: 0.37 - 11 kW3-ph 380 - 480 V: 0.37 - 22 kW
----
l(remove EMC screen)l
n
-n
---l
m (Nema 1)----
l* (DIN mount + screw)m (Nema 1 kit)
--l
---
4 to 16 kHz-- l
l
--
l(assistant panel)l
-l
2 / 15 / 1r+1t+(3r)
-m configurable
--l
---
n(SREA)- -----n
-----m
l
m
l
ABB drives featurefinder l ABB drives and motors catalogue 2014 5
All ABB drives are CE marked xx = ACS800 can be loaded with industry specific code, ++ = A wide range of encoder interfacesOther global approvals such as UL, cUL, CSA, like crane, winder, winch, spinning etc to suit high performance applicationsC-Tick, GOST-R also applicable
ABB drives for HVAC (ACH550 - p25)
3-ph 208 - 240 V: 0.75 - 75 kW3-ph 380 - 480 V: 1.1 - 355 kW
----
l (remove EMC screw)l
l
n
-l
---l
--
m (IP54)-l
l
l(550-02)-l
-m(IP54 drive)
l(to 11.0 kW), n thereafter4 to 12 kHz
-l l
l
--
l(assistant panel)l
-l
2 / 26 / 3r+(3r)
m
m configurable--l
m
-l
n(SREA)------n
----l
m
m
-l
ABB general purpose drives(ACS550 - p23)
3-ph 208 - 240 V: 0.75 - 75 kW3-ph 380 - 480 V: 1.1 - 355 kW
----
l (remove EMC screw)l
l
n
-l
---l
--
m (IP54)-l
l
l(550-02)-l
-m(IP54 drive)
l(to 11.0 kW), n thereafter4 to 12 kHz
-l
l
l
--
l(assistant panel)l
-l
2 / 26 / 3r+(3r)
m
m configurable--l
m
--
n(SREA)----
l Ex nA, Ex d/de,Ex tD/DIP only-n
-----m
---
ABB general purpose drivesfor fans and pumps
(ACS310 - p19)1-ph 200 - 240 V: 0.37 - 2.2 kW3-ph 200 - 240 V: 0.37 - 11 kW3-ph 380 - 480 V: 0.37 - 22 kW
----
l(remove EMC screen)l
n
-n
---l
m (Nema 1)----
l* (DIN mount + screw)m (Nema 1 kit)
--l
---
4 to 16 kHz-- l
l
--
l(assistant panel)l
-l
2 / 15 / 1r+1t+(3r)
-m configurable
--l
---
n(SREA)- -----n
-----m
l
m
l
ABB drives forwater and wastewater
(ACQ810-04 - p29)3ph 380 - 480 V: 1.1 - 400 kW
----m
l
m
-l, n(A,B Frame)
--
l(G frame)l(A-E frame)
l(G1/G2 frame)----l
---l
---
DTCl
-l
l
l
l
l
-l
l
2+(3) / 2+(1)6+2c+(4) / 2r+(2r)
-m configurable
l
l
l
m
l
-n(SREA)
--l
------n
----l
l
ABB industrial drivesand drive modules
(ACS800-01,-02,-04,-11,-14,-31 - p36)3-ph 230 V: 0.55 - 200 kW3-ph 400 V: 1.1 - 1450 kW3-ph 500 V: 1.5 - 1850 kW3-ph 690 V: 5.5 - 1900 kW
m(>400 kW)l (800-11, 800-14)
l (800-31)l
l (remove EMC screw)l
m, n(800-04 R7/8)-l
-l (800-31)
l(800-04, R7/R8, 800-14)l (800-04, R2 - R6)
l (800-01, -02, -11, -31)--
m (800 -01, -11, -31) IP55-
l(800-04*)l
l (800-02)-l
-m (800-04)
m
DTCl
-l
l
l(Drive AP)-l
---
3+(2) / 2+(2) 7+(6) / 3+(6r)
m
m configurablem
l
m
m
m
-n(RETA)
-n
--l
-n (NPCU req.)n (RDCO req.)n (RDCO req.)
---m
m
m
xx m
ABB industrial drivescabinet-drive
(ACS800-07, 17, -37 - p37)-
3-ph 400 V: 45 - 1450 kW3-ph 500 V: 55 - 1850 kW3-ph 690 V: 45 - 2800 kW
m(>400 kW)l (800-17)l (800-37)
l
l (remove EMC screw)l
m
-l
-l (800-37)
--l
m
m
m
---l
l
l
l(LC range)-m
DTCl
-l
l
l(Drive AP)-l
---
3+(2) / 2+(2)7+(6) / 3+(6r)
m
m configurablem
l
m
m
m
-n(RETA)
m
m
--l
-n (NPCU req.)n (RDCO req.)n (RDCO req.)
---m
m
m
xx m
ABB industrial drives(next generation)
(ACS880-01, 04, 07 - p44)3-ph 230 V: 0.55 - 75 kW
3-ph 400 V: 0.55 - 1400 kW3-ph 500 V: 0.55 - 1400 kW
3-ph 690 V: 4 - 2800 kW---l
l (remove EMC screw)l
m
-l
---
l(-04)l(-01)l(-07)m(-07)
m(-01, 07)-
l(-04)l(-01)
-l(-07)
l(Fan variable speed)--m
DTCl
-l
l
futurefuturel
-l
l
2+(3) / 2+(1)7+(4) / 3r+(2r)
m
m configurablel
l
l
m
l
-n(RETA or SREA))
m
m
l
m
------n
-----
ABB drives and motors
6 ABB drives and motors l ABB drives and motors catalogue 2014
Welcome to the 2014 edition of the ABB drives, motors and mechanical power transmission catalogue. Here you will find the basic technical details and prices for our most commonly purchased products, together with their most widely selected options. However, our range of products, systems and services is far more extensive. Extracts from this additional range are given on pages 41-61. Please do not hesitate to call us for any further information. Our contact details are on the back cover.
Thank you.
ABB drives and motors - matched packages ABB is one of the few companies in the world to make low voltage AC drives and motors. As such ABB is able to offer the perfectly designed, tested and approved motor-drive combination for any demanding process.
ABB’s AC drives are able to control AC motors over a power range from 100 W to 100 MW. ABB offers the lowest life cycle cost for each motor and drive, generating higher productivity and operating efficiency together with minimal environmental impact.
ABB also offers a totally new motor design. The SynRM motor brings a new dimension to high efficiency and performance. ABB offers this motor in two formats and with two drive products: IE4 motor or high output (HO) motor with either the ACS850 or the ACS880 making a dedicated machinery package (ACS850 + SynRM) or a dedicated industrial package (ACS880 + SynRM). More details can be found on page 8 and 9.
ABB Authorised Value Providers
ABB Authorized Value Providers l ABB drives and motors catalogue 2014 7
Authorised Value Providers - DrivesThese are the foremost drives network for the UK and Ireland. The 11 companies are strategically located around the UK and Ireland and have one of the largest stocks of AC drives, from 0.18 kW to 500 kW, available off-the-shelf.
Each provider is able to access up-to-the-minute central stock information using ABB’s online service. The members of the team have been handpicked by ABB to offer outstanding expertise in their local area.
Call Authorised Value Providers on:07000 ABB AVP (07000 222 287)
Authorised Value Providers - MotorsThese are a network of 13 independent companies that have pooled their resources to offer national and local customer access to electric motors up to 500 kW. The providers offer extensive technical knowledge and back-up, combined with the best equipped repair and maintenance facilities in Europe. Customers benefit from common service standards throughout the UK, access to ABB’s motor design and technical support, along with standardised reporting functions.
Authorised Value Provider members deliver sales, support, service and engineering expertise in seamless cooperation with ABB. They bring ABB’s products and services directly to your site.
1
1
13
3
5
12
11
10
7
64
5
4
23
9
8
6
11
2 97
10
8
1. ACS Drives & Control Systems Ireland
Tel: +353 (0)44 934 0242
2. APDS South West Tel: 0117 982 2049
3. Central Group Merseyside Tel: 0151 546 6000
4. EDC (Scotland) Scotland Tel: 0141 812 3222
5. Gibbons Engineering Group East Anglia Tel: 01621 868 138
6. Halcyon Drives Yorkshire and Greater Manchester Tel: 0113 236 1509
7. iDrives South East Tel: 01483 766 555
8. Inverter Drive Systems East Midlands Tel: 0115 944 1036
9. MKE Engineering Group South East Tel: 01795 438 436
10. Quantum Controls North East Tel: 01661 835 566
11. Sentridge Control Midlands Tel: 024 7655 3303
1. APDS South West Tel: 0117 982 2049
2. Beta Power Engineering Cheshire
Tel: 0161 432 9995
3. Campbell Electric Motors Ireland
Tel: +353(0) 1 4628 333
4. Central Group Merseyside Tel: 0151 546 6000
5. CovElec (Leics) Leicestershire Tel: 0116 269 8111
6. EDC (Scotland) Scotland Tel: 0141 812 3222
7. EMR Silverthorn Middlesex Tel: 020 8903 1390
8. H.G. Rewinds Staffordshire Tel: 01782 262525
9. Halcyon West Yorkshire Tel: 0113 236 1509
10. Heasell Electromechanical Services Hertfordshire Tel: 01763 243369
11. JJ Loughran Northern Ireland Tel: 028 8676 2295
12. MKE Engineering Group Kent Tel: 01795 438 436
13. Quantum Controls North East Tel: 01661 835 566
New in 2014 - ABB industrial drive, ACS880
Next generation ABB industrial drives, ACS880The ACS880 power range and features have further increased. Power is now available up to 2800 kW in cabinet build. IP55 and IP21 ranges are now fully available.
The range is the first low voltage AC drive to use ABB’s new common architecture that features the same control panel, harmonised parameters and functions, universal accessories and engineering tools. The architecture brings faster commissioning, minimal operator training and a familiarity across all ABB drives to be launched in the future.
The ACS880 family is available as a cabinet solution up to 2800 kW, with many factory factory fitted options.
ACS880 increases its range with multidrives and multidrive modulesThe ACS880 range now includes factory-built multidrive cabinets and a wide range of multidrive modules. The cabinet offering includes active rectifier sections (ISU) up to 6000 kVA, diode rectifier sections (DSU) up to 5500 kVA and a new style low cost regenerative rectifier unit (RRU) up to 6000 kVA. The multidrive line ups can be configured with a large selection of inverter sections, braking sections and integrated options.
ABB offers a comprehensive range of multidrive modules which allow system integrators to build complex drive systems of their own. ABB’s manuals and documentation and engineering tools provide comprehensive help to design and install the modules into either Rittal or bespoke cabinets
Safety built-inThe ACS880 offers integrated safety features, reducing the need for external safety components. Safe torque-off (STO) comes as standard, while options such as safe brake control (SBC), safe stop 1 (SS1), safe stop emergency (SSE) and safe maximum speed (SMS) are available when the dedicated safety module is installed.
Programming supportThe new ABB industrial drives support the CoDeSys programming environment, the same software used for ABB’s PLC, the AC500. This commonality allows easy integration of the drive and the AC500 PLC, since the control logic of the application can be designed using the same software, while some control logic can even be transferred from the PLC to the drive.
Accurate control of any motor typeInduction motors, synchronous motors and induction servo motors are all supported as standard by the drive, without any additional software. The latest motor design, SynRM (synchronous reluctance motor), is also supported by the ACS880 platform.
Next generation ABB industrial drive module, ACS880-04The ACS880-04 modules, which are designed and manufactured for system integrators, have a new addition to the power range. The R10, R11 frames extend the power rating up to 500 kW at 500 V. The module is mounted on wheels for easy manual handling. Input cables come in at the top and motor output connects to the bottom. These areas are shrouded and the shrouds remain in place when the module is removed for maintenance. This module makes it easier for system integrators to incorporate large powers into their cabinets.
8 What’s new in 2014 l ABB drives and motors catalogue 2014
New in 2014
What’s new in 2014 l ABB drives and motors catalogue 2014 9
Synchronous reluctance motor and drive packages - power range extension The SynRM motor range is further increased to include smaller motors: – IE4 SynRM, cast iron frame sizes 160 to 315 (11 to 315 kW)– High output (HO) SynRM, aluminium frame sizes 90 to 132
(1.1 to 37 kW), and cast iron frame sizes 160 to 315 kW (17 to 350 kW)
ABB’s new, highly energy-efficient SynRM motor is an innovative motor design that has no rotor windings (no squirrel cage), unlike traditional synchronous designs. The rotor, therefore, suffers virtually no rotor power losses and the rotor temperature remains lower than in conventional rotors. This helps achieve better power density, higher energy efficiency and increased maintenance intervals. The SynRM has a high output (HO) variant that produces the same power as traditional asynchronous AC motors but in mechanical frames which are two sizes smaller. This HO variant boasts IE3 efficiency figures. The second super premium high efficiency variant has the same physical dimensions as a standard synchronous AC motor, but is able to achieve IE4 efficiency levels, which is ideal for minimising energy usage in fan and pump applications.
The SynRM motors bring many advantages over traditional motors including reduced lifetime costs, quieter running, longer greasing intervals and less heat in the control room.
The SynRM requires an ABB variable-speed drive to control the speed of the shaft. There are currently two matched packages. One includes an ABB industrial drive, ACS880, matched to either an IE4 or HO motor. The machinery package includes an ACS850 machinery drive matched to either an IE4 or HO motor.
AC500 safety PLC AC500-S is the new safety PLC that fulfils the highest safety requirements and standards. The PLC is TÜV certified up to SIL3 (IEC 62061) and PL e (ISO13849). Separate safety and non-safety application programming provides flexibility and scaleability for customised solutions by using the complete AC500 CPU range. ABB’s new AC500-S safety PLC sets new standards in the field of safety engineering by bringing an incredibly powerful set of functions for trigonometric operations, including COS, SIN, TAN, ASIN, ACOS and LOG. Integrating AC500 with ACS880 and other safety hardware from Jokab Safety, allows ABB to offer a full safety solution.
ABB Dodge bearingsGrip Tight® adapter ball bearings:The Grip Tight adapter is shaft-ready right out of the box and offered in a variety of housing styles for normal and medium duty operations. With its patent pending pull/push adapter system, fully concentric 360º inner ring and completely interchangeable housing design, the Grip Tight adapter ball bearing is the easy-on/easy-off solution for damage-free shafting, reduced vibration and greater cost/inventory savings.
ISN bearingsAn ineffective seal can allow contaminants to enter a bearing, which can cause failure. However, with ISN bearing inserts our proven Trident seals are extremely effective for dirty environments, low-to-medium speeds, and normal ambient conditions. For higher speeds and harsher ambient conditions, ISN inserts offer labyrinth seals with corrosion-resistant flingers and steel clearance seal carriers.
What is an ABB micro drive, ACS55?The ABB micro drive meets the requirements of OEMs, machinery builders and panel builders. It is a component that is bought, together with other components, from a logistical distributor. The aim is for the ABB micro drive to be so small and simple that users of contactors and softstarters are encouraged to move to the benefits of variable-speed control. The ACS55 is a simple drive, programmed by switches. Extended programming is possible via a PC if required, as is programming without power.
Where can it be used?– Washing machines – Dryers– Mixers – Dishwashers – Boring machines – Treadmills – Pizza ovens – Car washing machines – Vacuum cleaners – Rotating billboards– Sliding doors – Electric gates
Highlights– Quick and easy installation - less than 5 minutes– No programming - easy and descriptive interface– Can be programmed via DriveConfig if needed to access
extended functions (useful to OEMs)– Compact size and narrow shape– Ideal drive for DIN-rail mounting– 110 V single phase – input gives 240 V, 3-phase output– Two mounting orientations– IP20 as standard– No control panel required
– User interface via three rotary switches and a further eight on/off function DIP switches located on panel front
– Potentiometer option– Integral EMC filter for 1st environment (EN61800-3),
unrestricted distribution (C1)– Optional first environment filter for extended cable runs– Optimised switching frequency for low noise (up to 16 kHz)– Silent motor
For more details, please refer to Technical Catalogue 3AFE68899842
10 ABB micro drive l ABB drives and motors catalogue 2014
Feature Advantage Benefit
No programming Inverter parameter settings with DIP switches and Faster set-up
if required potentiometers. Extended programming is possible Easier configuration
via DriveConfig if needed Easy drive for new users
Compact size and Up to 0.37 kW, 45 mm width; 2.2 kW, 67.5 mm width Less space required for installation
narrow shape
Removable mounting clip Removable clip allows DIN-rail and wall-mounting Flexible and easy mounting
from back and side of the unit
DriveConfig kit Fast and safe configuration of an unpowered drive Simple programming for high volume OEMs - programming
in the box, no mains power needed
EMC First environment. C1 EMC filters as standard (‘E’ model) Low EMC emissions
Automatic switching Increases switching frequency automatically when drive Provides lowest possible noise without derating the drive
frequency temperature is decreased
110-240 V AC, single Output always capable of full 240 V, 3-phase, regardless of Can easily replace single phase cap start motors
phase supplies supply voltage
RoHS compliance Compliance achieved during 2007 Environmentally friendly drives
Main features
ABB micro drive0.18 kW to 2.2 kW, ACS55Motor control method - scalar200/240 V, 1-phase supply, 3-phase output, 0.18 kW - 2.2 kW
100/120 V, 1-phase supply, 3-phase output, 0.18 kW - 0.37 kW
ABB micro drive
ACS55 – Ratings, types, voltages, prices and dimensions
ACS55 typical I/O connections
Options and interfacesPotentiometerPotentiometer with two switches: start/stop and forward/reverse direction. No external power source is needed for the potentiometer, connects directly to drive I/O.
DriveConfig programming with no powerTo increase the number of applications possible with the ACS55, the DriveConfig kit can be used to access an extended parameter set. It is still possible to programme in the usual way, if these extended features are not required. DriveConfig also allows programming in the box without power.
H1 = Height with mounting clipH2 = Height without mounting clipW = WidthD = Depth
H2H1
W
D
Nominal ratings Frame Fuse Heat Cooling Type List
Nominal Input Nom. output Max A dissipation requirements price
current current output Type gG W m3/h
kW A A A
With EMC filter
0.18 6.4 1.4 2.1 A 10 24 + Nat Vent ACS55-01E-01A4-1 £101
0.37 9.5 2.2 3.3 A 16 35 + Nat Vent ACS55-01E-02A2-1 £113
Without EMC filter
0.18 6.4 1.4 2.1 A 10 24 + Nat Vent ACS55-01N-01A4-1 £98
0.37 9.5 2.2 3.3 A 16 35 + Nat Vent ACS55-01N-02A2-1 £106
Frame H1 H2 W D Weight
size mm mm mm mm Kg
A 170 146.5 45 128 0.65
B 170 146.5 67.5 128 0.70
C 194 171 70 159 1.1
D 226 203 70 159 1.1
+ Ensure minimum installation space is provided, see User’s Manual for details
+ Ensure minimum installation space is provided, see User’s Manual for details
Nominal ratings Frame Fuse Heat Cooling Type List
Nominal Input Nom. output Max A dissipation requirements price
current current output Type gG W m3/h
kW A A A
With EMC filter
0.18 4.4 1.4 2.1 A 10 21 + Nat Vent ACS55-01E-01A4-2 £93
0.37 6.9 2.2 3.3 A 16 32 + Nat Vent ACS55-01E-02A2-2 £102
0.75 10.8 4.3 6.5 B 16 51 + Nat Vent ACS55-01E-04A3-2 £122
1.5 18.2 7.6 11.4 D 25 74 26 ACS55-01E-07A6-2 £170
2.2 22 9.8 14.7 D 32 103 26 ACS55-01E-09A8-2 £199
Without EMC filter
0.18 4.4 1.4 2.1 A 10 21 + Nat Vent ACS55-01N-01A4-2 £88
0.37 6.9 2.2 3.3 A 16 32 + Nat Vent ACS55-01N-02A2-2 £97
0.75 10.8 4.3 6.5 B 16 51 + Nat Vent ACS55-01N-04A3-2 £114
1.5 18.2 7.6 11.4 C 25 74 26 ACS55-01N-07A6-2 £159
2.2 22 9.8 14.7 C 32 103 26 ACS55-01N-09A8-2 £186
200/240 V, 1-phase supply, 3-phase output
100/120 V, 1-phase supply, 3-phase output
Dimensions and weights
ABB micro drive l ABB drives and motors catalogue 2014 11
What is an ABB micro drive, ACS150?The ABB micro drive meets the requirements of OEMs, machinery builders and panel builders. It is a component that is bought, together with other components, from a logistical distributor. ABB micro drives are designed to encourage users of contactors and softstarters to move to the benefits of variable-speed control. The ACS150 extends the capability of the ACS55 (see page 10), by adding an extended range of power frames and programmability. The ACS150 can solve more difficult tasks like PID functionality. To retain the simplicity of an ABB micro drive, the ACS150 does not have a serial communications interface or extended options but does have a fixed keypad and speed control potentiometer.
Where can it be used?ACS150 can be used to control less demanding components in any machine, fans or pumps or anywhere where a fixed speed motor needs to go to variable-speed control. The functionality of the drive is designed to compliment the ABB machinery drives and ABB motion control drives.
Highlights– PID controller built-in– DC hold stop ensures stationary motor shaft– IR compensation improves starting torque for heavy loads– Parameter lock prevents tampering by unauthorised staff– DIN rail or screw mounting as standard
– IP20 enclosure– Fixed basic control panel– Dedicated control potentiometer– Two-year warranty– Flashdrop - parameter programming whilst still in its box -
excellent for OEMs– Protected against wiring errors: shows fault if power cable is
inadvertently connected to motor terminals– Automatic noise reduction– Optional short or long parameter mode for standard
or advanced users– Unified height across the power range simplifies
cabinet design– Drive branding possible for large users
* For details of FlashDrop, see user interfaces in ABB machinery drive section (page 18)
For more details, please refer to Technical Catalogue 3AFE68596114
12 ABB micro drive l ABB drives and motors catalogue 2014
Feature Advantage Benefit
FlashDrop* Faster and easier drive set-up and commissioning for No need for high voltage safe programming areas
volume manufacturing. Programming in the box Parameters can be hidden for clarity
Programme the drive during machine production build-up
Fixed interface Simple drive with comfortable and robust interface Integrated control panel with clear LCD display, backlight
Easy to navigate parameter structure and buttons for editing and control
Fixed potentiometer Intuitive speed setting Integrated potentiometer. Settings shown on the
control panel
Programmable functions Useful control functions like PID, accelerating rates and Take control of the motor and reduce cost in the
start/stop modes included installation
Built-in EMC filter No need for external filtering 2nd environment built-in filter. Complying with IEC 61800-3
as standard
Built-in brake chopper Reduced cost, saved space and simple wiring 100 percent braking capability
Flexible installation Optimum layout and efficient cabinet space usage Screw, DIN-rail, sideways and side-by-side mounting
Unified height and depth
Drive protection Latest solutions to protect the drive and offer trouble-free The drive protects itself when power is connected to the
use and the highest quality motor terminals. I/O protected against short-circuit.
Coated boards included as standard
Brand labelling Drive logo, control panel logo, manuals and box can be Drives and packaging badged to your design
printed with machine builders logo and name
RoHS compliance Compliance achieved during 2007 Environmentally friendly drives
Main features
ABB micro drive0.37 kW to 4 kW, ACS150Motor control method - scalar200/240 V, 1-phase supply, 0.37 kW - 2.2 kW
200/240 V, 3-phase supply, 0.37 kW - 2.2 kW
380/480 V, 3-phase supply, 0.37 kW - 4 kW
ABB micro drive
ACS150 – Ratings, types, voltages and prices
+ Ensure enough space around the unit - refer to the User’s Manual for details
ABB micro drive l ABB drives and motors catalogue 2014 13
Nominal ratings Frame Fuse Heat Cooling Type List
Nominal Nom. output Max A dissipation requirements price
current Output Type gG W m3/h
kW A A
0.37 2.4 4.2 R0 10 25 +Nat Vent ACS150-01E-02A4-2 £100
0.75 4.7 8.2 R1 16 46 24 ACS150-01E-04A7-2 £117
1.1 6.7 11.7 R1 20 71 24 ACS150-01E-06A7-2 £147
1.5 7.5 13.1 R2 25 73 21 ACS150-01E-07A5-2 £165
2.2 9.8 17.2 R2 35 96 21 ACS150-01E-09A8-2 £198
200/240 V, 1-phase supply voltage
200/240 V, 3-phase supply voltage3-phase, 240 V is also available for customers supplying the North American market. Please enquire for details.
+ Ensure enough space around the unit - refer to the User’s Manual for detailsThe drive can be fitted with the NEMA 1 kit for easy wall-mounting and convenient protection, see user interfaces in ABB machinery drive section, page 18.
Nominal ratings Frame Fuse Heat Cooling Type List
Nominal Nom. output Max A dissipation requirements price
current Output Type gG W m3/h
kW A A
0.37 1.2 2.1 R0 10 11 +Nat Vent ACS150-03E-01A2-4 £159
0.55 1.9 3.3 R0 10 16 +Nat Vent ACS150-03E-01A9-4 £168
0.75 2.4 4.2 R1 10 21 13 ACS150-03E-02A4-4 £183
1.1 3.3 5.8 R1 10 31 13 ACS150-03E-03A3-4 £201
1.5 4.1 7.2 R1 16 40 13 ACS150-03E-04A1-4 £220
2.2 5.6 9.8 R1 16 61 19 ACS150-03E-05A6-4 £315
3 7.3 12.8 R1 16 74 24 ACS150-03E-07A3-4 £379
4 8.8 15.4 R1 20 94 24 ACS150-03E-08A8-4 £431
380/480 V, 3-phase supply voltage
ABB micro drive
ACS150 – Dimensions, I/O and options
H1 = Height without fastenings and clamping plate H2 = Height with fastenings but without clamping plate H3 = Height with fastenings and clamping plate H4 = Height with fastenings and NEMA 1 connection box H5 = Height with fastenings, NEMA 1 connection box and hood W = Width D = Depth
Dimensions and weightsCabinet-mounted drives (UL open), wall mounted drives (NEMA 1)
ROCOM RONC RONO
DI configuration NPNPNP is possible
0 - 20 mAGround cablescreen atsourcing end
0 - 10 V can be used by connecting potto 10V, GND and AI, DIP switch to ‘u’
ACS150 I
U
fwd/ rev
SCR AI
GND +10 V +24 V GND
DCOM DI1 DI2 DI3 DI4 DI5
start/ stop
DIP switch analogue Input
Const. speed 1
Const. speed 2
Change ramp
All I/O shownas defaultsettings. Canbe configuredto other set-ups.
Fault
Options available– Input and output chokes– Brake chopper resistors (all drives in the ACS150 range
have integral chopper)– 1st. environment EMC filters - footprint style– Low leakage EMC filters < 30mA leakage– FlashDrop - programming without power– NEMA kit allows installations to be neater and provides
mechanical support for glanded cables
ACS150 user interfacesThe ACS150 has a simple user interface, consisting of I/O connections and a fixed programming keypad. An integrated speed control potentiometer is also provided.
W
D
H5H4H3H2H1
D
W
ACS150 typical I/O connections
Frame IP20 UL open NEMA 1
size H1 H2 H3 W D Weight H4 H5 W D Weight
mm mm mm mm mm Kg mm mm mm mm Kg
R0 169 202 239 70 142 1.1 257 280 70 142 1.5
R1 169 202 239 70 142 1.3 257 280 70 142 1.5
R2 169 202 239 105 142 1.5 257 282 105 142 1.5
Removable clip for brand labelling
EMC filter grounding screw (EMC)
Varistor grounding screw (VAR)
Analogue input signal selector (U/I)
Input, brake resistor and motor connections
Integrated interface
FlashDrop connection
Integrated potentiometer
I/O connections
14 ABB micro drive l ABB drives and motors catalogue 2014
What is an ABB machinery drive?ABB machinery drives are designed for the machine building sector. In serial type manufacturing the consumed time per unit is critical. The drive is designed to be optimal in terms of installation, setting parameters, available machinery features and commissioning. The basic product has been made as user-friendly as possible, yet providing high intelligence. The drive offers diverse functionality to cater for the most demanding needs. The drive is also equipped with a dual channel safe torque-off interface to SIL3/PL e.
Where can it be used?ABB machinery drives are designed to meet the requirements of an extensive range of machinery applications. The drive is ideal for food and beverage, material handling, textile, printing, rubber and plastics and woodworking applications. The higher IP66 class variant meets all of the relevant hygiene requirements for the food and beverage industry.
The functionality of this ABB drive is designed to complement the ABB motion control drives and the ABB micro drives.
Highlights– FlashDrop - parameter programming with drive still in
its box - excellent for OEMs– Sequence programming designed for food and beverage
and materials handling applications - Eight-steps included
– Impressive software and compact hardware– Unified height and depth across the power range
simplifies cabinet design– Optimised interfaces for users and machines
(can select Basic or Assistant control panel)– Protected against wiring errors: shows fault if power cable
is inadvertently connected to motor terminals– Automatic noise reduction– Drive branding possible for large users
For more details, please refer to Technical Catalogue 3AFE68596106
* For details of FlashDrop, see user interfaces in ABB machinery drive section, page 18
ABB machinery drive l ABB drives and motors catalogue 2014 15
Feature Advantage Benefit
FlashDrop* Faster and easier drive set-up and commissioning for Fast, safe and trouble-free method to set up and commission
volume manufacturing. Programming with no power without powering up the drive - patented
Safe torque-off Built-in compliance to new machinery directive SIL3/PL e certified dual channel input - TÜV approved
Sequence programming Application specific 8-state programming with Logic programming included as standard
comprehensive triggering conditions Reduces the need for external PLC
Common DC link Connection to existing DC power sources (patented) Easy integration into high performance machines
User interfaces Wide range, including Assistant panel Cost efficient approach - meets requirements of OEM
Fieldbus Extensive range of industrial fieldbus option modules available Connectability to all of the most popular fieldbuses
24 V ‘live keypad’ Connect 24 V to the drive via the MPOW option Keep fieldbus, control card and I/O healthy while able to
operation remove the main supply - safer maintenance
Built-in EMC filter 2nd environment filter complying with IEC 61800-3 No extra space, parts, time or cost required
as standard
Built-in brake chopper 100 percent braking capability Reduces cost, saves space and simplifies wiring
Drive protection Latest solutions to protect the drive and offer trouble-free The drive protects itself when power is connected to the
use and the highest quality motor terminals. I/O protected against short-circuit
Coated boards included as standard
IP66/69k enclosure option Makes drive suitable for hose down applications Meets food hygiene standards in a wall-mounted enclosure
Brand labelling Drive logo, control panel logo, manuals and box can be Drives and packaging badged to your design
printed with machine builders logo and name
RoHS compliance Compliance achieved during 2007 Environmentally friendly drives
Main features
ABB machinery drive0.37 kW to 22 kW, ACS355Motor control method - scalar, vector (open and closed loop)200/240 V, 1-phase supply, 0.37 kW - 2.2 kW
200/240 V, 3-phase supply, 0.37 kW - 11 kW
380/480 V, 3-phase supply, 0.37 kW - 22 kW
ABB machinery drive
ACS355 - Ratings, types, voltages and prices
+ Ensure enough space around the unit - refer to the User’s Manual for details* Note: IP20 drives require a keypad for parameter alteration** Note: IP66 drives are always delivered with the Assistant keypad
+ Ensure enough space around the unit - refer to the User’s Manual for details* Note: IP20 drives require a keypad for parameter alteration** Note: IP66 drives are always delivered with the Assistant keypad
† Price of control panel only when purchased with drivePanel mounting kit and user interface descriptions, see page 18
16 ABB machinery drive l ABB drives and motors catalogue 2014
Nominal ratings Frame Fuse Heat Cooling Type IP20 list IP66 list
Nominal Nom. output Max A dissipation requirements (code shown is IP20) price without price with
current Output Type gG W m3/h control control
kW A A panel* panel**
0.37 2.4 4.2 R0 10 48 +Nat Vent ACS355-01E-02A4-2 £111 n/a
0.75 4.7 8.2 R1 16 72 24 ACS355-01E-04A7-2 £139 n/a
1.1 6.7 11.7 R1 20 97 24 ACS355-01E-06A7-2 £163 n/a
1.5 7.5 13.1 R2 25 101 21 ACS355-01E-07A5-2 £179 n/a
2.2 9.8 17.2 R2 35 124 21 ACS355-01E-09A8-2 £219 n/a
200/240 V, 1-phase supply voltage
200/240 V, 3-phase supply voltage3-phase, 240 V is also available for customers supplying the North American market. Please enquire for details.
Nominal ratings Frame Fuse Heat Cooling Type IP20 list IP66 list
Nominal Nom. output Max A dissipation requirements (code shown is IP20 price without price with
current Output Type gG W m3/h For IP66 add +B063) control control
kW A A panel* panel**
0.37 1.2 2.1 R0 10 35 +Nat Vent ACS355-03E-01A2-4 £189 £400
0.55 1.9 3.3 R0 10 40 +Nat Vent ACS355-03E-01A9-4 £199 £402
0.75 2.4 4.2 R1 10 50 13 ACS355-03E-02A4-4 £218 £417
1.1 3.3 5.8 R1 10 60 13 ACS355-03E-03A3-4 £247 £463
1.5 4.1 7.2 R1 16 69 13 ACS355-03E-04A1-4 £300 £526
2.2 5.6 9.8 R1 16 90 19 ACS355-03E-05A6-4 £348 £600
3 7.3 12.8 R1 16 107 24 ACS355-03E-07A3-4 £454 £777
4 8.8 15.4 R1 20 127 24 ACS355-03E-08A8-4 £517 £882
5.5 12.5 21.9 R3 25 161 52 ACS355-03E-12A5-4 £599 £1,043
7.5 15.6 27.3 R3 30 204 52 ACS355-03E-15A6-4 £777 £1,237
11 23.1 40.4 R3 50 301 71 ACS355-03E-23A1-4 £949 n/a
15 31.0 54.3 R4 80 408 96 ACS355-03E-31A0-4 £1,216 n/a
18.5 38.0 66.5 R4 100 498 96 ACS355-03E-38A0-4 £1,443 n/a
22 44.0 77.0 R4 100 588 96 ACS355-03E-44A0-4 £1,764 n/a
380/480 V, 3-phase supply voltage
Control panel Type Price
Assistant control panel ACS-CP-A £86†
Basic keypad ACS-CP-C £24
Control panel for ACS355
W
D1D2
H3H2H1
D1D2
W
H5 HH4
D1W
ABB machinery drive
ACS355 – Dimensions, I/O and options
Typical control connectionsSTO connectionsThe ACS355 has a dual channel STO (safe torque-off) input as standard, certified to BS EN 62061 and BS EN 13849-1
Options available– Input and output chokes– Brake chopper resistors (all drives in the ACS355 range
have integral chopper)– 1st. environment EMC filters - footprint style– Low leakage EMC filters < 30 mA leakage– FlashDrop, programming in the box– Fieldbus modules– NEMA kit allows installations to be neater and provides
mechanical support for glanded cables– An extensive range of user interfaces is available - please
see following pages– IP66 pressure relief valves
H = HeightH1= Height without fastenings and
clamping plateH2 = Height with fastenings but without
clamping plateH3 = Height with fastenings and
clamping plateH4 = Height with fastenings and NEMA 1
connection boxH5 = Height with fastenings, NEMA 1
connection box and hoodW = WidthD1 = Standard depthD2 = Depth with MREL or MTAC option
X1C:STO Safety switch
OUT1
OUT2
IN1
IN2
1
2
3
4
ABB machinery drive l ABB drives and motors catalogue 2014 17
IP20 UL Open NEMA 1/UL Type 1 IP66/67/UL Type 4x
Frame H1 H2 H3 W D1 D2 Weight H4 H5 W D1 D2 Weight H W D1 Weight
size mm mm mm mm mm mm Kg mm mm mm mm mm kg mm mm mm Kg
R0 169 202 239 70 161 187 1.2 257 280 70 169 187 1.6 - - -
R1 169 202 239 70 161 187 1.2 257 280 70 169 187 1.6 305 195 281 7.7
R2 169 202 239 105 165 191 1.5 257 282 105 169 191 1.9 - - - -
R3 169 202 236 169 169 195 2.5 260 299 169 177 195 3.1 436 246 277 13
R4 181 202 244 260 169 195 4.4 270 320 260 177 195 5.0 - - - -
Dimensions and weights
0 - 20 mAGround cablescreen at sourcing end
DIP switchanalogue inputs
ABB machinery drive
Assistant control panel (+J400)The Assistant control panel features a multilingual alphanumeric display for easy drive programming. The control panel has various assistants and a built-in help function to guide the user. It includes a real-time clock, which is used during fault logging and in controlling the drive, such as start/stop. The control panel can be used for copying parameters for backup or for downloading to another drive. A large graphical display and soft keys make it extremely easy to navigate. For further information, see ABB general purpose drive section on page 28.
Basic control panel (+J404)The Basic control panel features a single line numeric display. The panel can be used to control the drive, set the parameter values or copy them from one drive to another, or view changes.
Panel coverThe panel cover protects the drive when no control panel is used. The ABB machinery drive is delivered with a panel cover as standard, thereby providing a cost effective package. In addition, there are two alternative control panels available as options, see above.
NEMA 1 kitThe NEMA 1 kit is a convenient cover which is added to the drive and enables easy wall-mounting. It includes a connection box for cable gland or conduit tube installation and a hood for protection against dirt and dust.
Panel mounting kit, IP54 and IP66The panel mounting kits enable mounting of control panels onto cabinet doors. These kits includea 3 m extension cable, a gasket, mounting screws and a mounting template - two versions are now available, IP54 and IP66. The IP66 has an additional keypad membrane cover.Note: IP66 cover is not suitable for outdoor use.
Relay extension module (+L511)Add an additional three relays to the ACS355 to allow greater use of the drives programme. Fits behind the keypad.
Potentiometer (+J402)Potentiometer with two switches: start/stop and forward/reverse direction. No external power source is needed for the potentiometer. Fits to the drive I/O.
FlashDropProgramme the drive whilst still in the box, with no power. Perfect for OEMs and machine builders. FlashDrop is a powerful palm-sized tool for fast and easy parameter selecting and setting. It gives the possibility to hide selected parameters to protect the machine. The tool stores 20 parameter sets, which can be moved between a PC and a drive. Safe programming during machine building production for unskilled staff.
Fieldbus interfacesExtensive range of plug-in fieldbus interfaces, allowing connection to Profibus, DeviceNet, CanOpen, Modbus RTU and Ethernet and many others.
24V “live kepad” optionsThere are two ways of powering the fieldbus modules, so that they operate when the main power is removed.
FEPA - maintains power to the fieldbus module only. MPOW (+G406) - Powers the fieldbus module, the control card, the drive I/O and the drive keypad, generating the functionality commonly known as ‘live keypad’ operation.
DriveWindow Light PC toolDriveWindow Light is a parameterisation and commissioning tool used to set-up and commission the drive. Monitoring and diagnostic facilities are included, as well as a local control panel.Wizards are included to guide the user through the most commonly performed tasks.
ACS355 – User interfaces
18 ABB machinery drive l ABB drives and motors catalogue 2014
What is an ABB general purpose drive for fans and pumps?ABB general purpose drives include a dedicated fan and pump controller designed for squared-torque applications such as booster pumps, submersible pumps, irrigation pumps and centrifugal fans.
The drive design includes a powerful set of features which benefit pump and fan applications including built-in PID controllers and PFC (pump and fan control). The drives also have pre-programmed protection functions such as pipe cleaning (anti-jam) and duty standby functionality, including soft pipe filling to reduce leaks.
These features, combined with pre-programmed application macros, an intuitive user interface, and several assistant screens, speed up the installation, parameter setting and commissioning of the drive.
Where can it be used?The ABB general purpose drive’s software features are ideal for solving the challenges and issues surrounding pumping in general, and those of water and wastewater in particular.
The drive is designed to compliment the features offered by the industry specific products for water and wastewater (see page 29).
Highlights– Pump and soft pump and fan control (PFC and SPFC), for
multi-pump and soft fill control– Pipe cleaning (anti-jam) and pipe fill functions– Multiple PID set points, allowing for automatic duty/assist/
standby schemes to be implemented– Energy efficiency counters, real-time clock– Energy optimiser – optimises the motor control for the
application to run with minimum energy requirements– Load analyser for optimised dimensioning of the drive,
motor and process– Embedded Modbus RS-485 fieldbus interface– FlashDrop tool for fast parameter setting, without mains power
For more details, please refer to Technical Catalogue 3AUA0000051082
ABB general purpose drives for fans and pumps l ABB drives and motors catalogue 2014 19
* For details of FlashDrop, see user interfaces (page 22)
Feature Advantage Benefit
Pump and fan control One drive controls several pumps or fans and eliminates the Saves cost of additional drives and external PLC
(PFC) feature to control need for an external programmable logic controller Longer life for pump or fan system while reducing
pumps and fans in Interlock function enables one motor to be disengaged from maintenance time and costs. Maintenance can
parallel the mains supply while others continue operating in parallel be carried out safely without stopping the process
Soft pump and fan control Reduces unwanted pressure peaks in pumps and pipelines Reduces maintenance costs and leaks typically seen in DOL
feature (SPFC) when an auxiliary motor is started starting. Longer life for pump or fan system
Pump protection functions Pre-programmed features like: Reduces maintenance costs
Pipe cleaning (anti-jamming), inlet/outlet pressure Smoother processes: improved and optimised system
supervision and detection of under or overload for Longer life for pump and fan system, reduced maintenance
preventive maintenance costs
Energy monitoring and Drive monitors the saved energy compared to equivalent Energy savings presented in local currency and CO2
optimising features DOL operation Consumed energy optimised across the speed and load
Drive controls the motor voltage dependant on the load range
Full output current at Drive can be operated in ambient temperatures up to 50°C Optimised drive dimensioning for wide temperature range
50°C ambient without de-rating the output current
Unified height and Optimum installation layout, as all drive frames are the Space savings. Easier to lay the cabinet back panel out
depth same height – only the width changes
Best-in-class user Assistant and Basic keypads with intuitive operation. Short Users are supported as they program the drive, can tailor
interfaces and long menus, Assistants and wizards for ease of use the open menu views to suite there customer needs
FlashDrop* Faster and easier drive set up and commissioning for Fast, safe and trouble-free method to set up and commission
volume manufacturing without powering up the drive - patented
RoHS compliance Compliance achieved during 2007 Environmentally friendly drives
Main features
ABB general purpose drive for fans and pumps0.37 kW to 22 kW, ACS310Motor control method – Scalar200/240 V, 1-phase supply, 0.37 kW - 2.2 kW
200/240 V, 3-phase supply, 0.37 kW - 11 kW
380/480 V, 3-phase supply, 0.37 kW - 22 kW
ABB general purpose drive for fans and pumps
ACS310 – Ratings, types, voltages and prices
+ Ensure enough space around the unit - refer to the User’s Manual for details* Drives require a control panel for parameter alterationFor 50°C ratings contact ABB
** Price of control panel only when purchased with drivePanel mounting kit and user interface descriptions, see page 22
+ Ensure enough space around the unit - refer to the User’s Manual for details* Drives require a control panel for parameter alteration For 50°C ratings contact ABB
20 ABB general purpose drives for fans and pumps l ABB drives and motors catalogue 2014
Nominal ratings Max Frame Fuse Heat Cooling Type IP20 list price
Nominal Nom. output Output A dissipation requirements without
current A Type gG W m3/h control
kW A panel*
0.37 2.4 4.0 R0 10 48 +Nat Vent ACS310-01E-02A4-2 £110
0.75 4.7 7.9 R1 16 72 24 ACS310-01E-04A7-2 £125
1.1 6.7 11.4 R1 20 97 24 ACS310-01E-06A7-2 £146
1.5 7.5 12.6 R2 25 101 21 ACS310-01E-07A5-2 £162
2.2 9.8 16.5 R2 35 124 21 ACS310-01E-09A8-2 £197
200/240 V, 1-phase supply voltage
Nominal ratings Max Frame Fuse Heat Cooling Type IP20 list price
Nominal Nom. output Output A dissipation requirements without
current A Type gG W m3/h control
kW A panel*
0.37 1.3 2.1 R0 10 35 +Nat Vent ACS310-03E-01A3-4 £171
0.55 2.1 3.3 R0 10 40 +Nat Vent ACS310-03E-02A1-4 £180
0.75 2.6 4.2 R1 10 50 13 ACS310-03E-02A6-4 £197
1.1 3.6 5.8 R1 10 60 13 ACS310-03E-03A6-4 £219
1.5 4.5 7.2 R1 15 69 13 ACS310-03E-04A5-4 £285
2.2 6.2 9.8 R1 15 90 19 ACS310-03E-06A2-4 £315
3 8 12.8 R1 20 107 24 ACS310-03E-08A0-4 £404
4 9.7 15.4 R1 25 127 24 ACS310-03E-09A7-4 £459
5.5 13.8 21.9 R3 30 161 52 ACS310-03E-13A8-4 £533
7.5 17.2 27.3 R3 35 204 52 ACS310-03E-17A2-4 £702
11 25.4 40.4 R3 50 301 71 ACS310-03E-25A4-4 £857
15 34.1 54.3 R4 80 408 96 ACS310-03E-34A1-4 £1,101
18.5 41.8 66.5 R4 100 498 96 ACS310-03E-41A8-4 £1,284
22 48.4 77.0 R4 100 588 96 ACS310-03E-48A4-4 £1,569
380/480 V, 3-phase supply voltage
Control panel Type Price
Assistant control panel ACS-CP-A £86**
Basic keypad ACS-CP-C £24
Control panel for ACS310
200/240 V, 3-phase supply voltage3-phase 240 V is also available for customers supplying the North American market. Please enquire for details.
ABB general purpose drive for fans and pumps
ACS310 – Dimensions, I/O and options
H1 = Height without fastenings and clamping plate
H2 = Height with fastenings but without clamping plate
H3 = Height with fastenings and clamping plate
H4 = Height with fastenings and NEMA 1 connection box
H5 = Height with fastenings, NEMA 1 connection box and hood
W = WidthD = Depth
IP20 UL Open NEMA 1/UL Type 1
Frame H1 H2 H3 W D Weight H4 H5 W D Weight
size mm mm mm mm mm Kg mm mm mm mm kg
R0 169 202 239 70 161 1.1 257 280 70 169 1.5
R1 169 202 239 70 161 1.3 257 280 70 169 1.7
R2 169 202 239 105 165 1.5 257 282 105 169 169
R3 169 202 236 169 169 2.9 260 299 169 177 3.5
R4 181 202 244 260 169 4.4 270 320 260 177 5.0
Dimensions and weights
Typical control connections– All I/O are programmable for other configurations
Options available– Input and output chokes– ACS310 has no braking options– 1st environment EMC filters - footprint style– Low leakage EMC filters < 30mA leakage– FlashDrop– NEMA kit allows installations to be neater and provides
mechanical support for glanded cables– An extensive range of user interfaces is available - please
see following pages
H1 H3H2
D
W
Cabinet-mounted drives (IP20 UL open)
D
W
H5H4
Wall-mounted drives (NEMA 1)
ABB general purpose drives for fans and pumps l ABB drives and motors catalogue 2014 21
0 - 20 mAGround cablescreen at sourcing end
DIP switchanalogue inputs
ABB general purpose drive for fans and pumps
ACS310 – User interfaces
Assistant control panel (+J400)The Assistant control panel features a multilingual alphanumeric display for easy drive programming. The control panel has various assistants and a built-in help function to guide the user. It includes a real time clock, which is used during fault logging and in controlling the drive, such as start/stop. The control panel can be used for copying parameters for backup or for downloading to another drive. A large graphical display and softkeys make it extremely easy to navigate. For further information, see ABB general purpose drive section on page 28.
Basic control panel (+J404)The Basic control panel features a single line numeric display. The panel canbe used to control the drive, set the parameter values or copy them fromone drive to another.
Panel coverThe panel cover protects the drive’s connection when no control panel is used. The ABB general purpose drive is delivered with a panel cover as standard, thereby providing a cost effective package. In addition, there are two alternative control panels available as options, see above.
NEMA 1 kitThe NEMA 1 kit is a convenient cover which is added to the drive and enables easy wall-mounting. It includes a connection box for cable gland or conduit tube installation and a hood for protection against dirt and dust.
Panel mounting kit, IP54 and IP66The panel mounting kit enables mounting of control panels on cabinet doors. These kits include a 3 m extension cable, a gasket, mounting screws and a mounting template - two versions are now available, IP54 and IP66. The IP66 has an additional keypad membrane cover.Note: IP66 cover is not suitable for outdoor use.
Relay extension module (+L511)Add an additional three relays to the ACS310 to allow greater use of the PFC program. Fits behind the keypad.
FlashDropProgramme the drive whilst still in the box, with no power. Perfect for OEMs and machine builders. FlashDrop is a powerful palm sized tool for fast and easy parameter selecting and setting. It gives the possibility to hide selected parameters to protect the machine. The tool stores 20 parameter sets, which can be moved between a PC and a drive. Safe programming during machine building production for unskilled staff.
Fieldbus communicationsACS310 has no industrial fieldbus interfaces, but it does have an RS485 Modbus communications link built-in. This link can be used to communicate to industrial HMIs or remote monitoring devices or to a fieldbus via a suitable gateway.
DriveWindow Light PC toolDriveWindow Light is a parameterisation and commissioning tool used to set-up and commission the drive. Monitoring and diagnostic facilities are included, as well as a local control panel. Wizards are included to guide the user through the most commonly performed tasks.
22 ABB general purpose drives for fans and pumps l ABB drives and motors catalogue 2014
What is an ABB general purpose drive?The ABB general purpose drive is simple to buy, install, configure and use, saving considerable time. It is widely available through ABB’s distributors. The drive has a common user and process interface, common software tools for sizing, commissioning and maintenance and common spare parts. A wide range of fieldbus options gives excellent connectivity and new energy monitoring allows energy management. IP21 and IP54 variants mean it can be installed in almost any environment.
Where can it be used?The ABB general purpose drive can be used in a wide range of industries. Typical applications are many and varied. The vector motor control means the drive can be used to fulfil the needs of reasonably demanding applications of all kinds. For highly demanding torque applications, the ABB industrial drive with DTC should be chosen. The ABB general purpose drive is ideal in those situations where there is a need for simplicity to install, commission and use and where reasonable amounts of flexibility and functionality are required.
Highlights– Easy ordering– Quick installation– Rapid start-up – Trouble-free use
– Easy interfacing– Wide power range in wall-mounted IP21 and IP54 variants – Assistant control panel for intuitive use – Patent pending swinging choke for superior harmonic
reduction, even at reduced motor load– Sensorless vector and scalar control– Integral EMC filter for 1st and 2nd environment as standard– Flexible fieldbus system with built-in Modbus and numerous
internally mountable fieldbus adapters– New energy monitoring features record energy, CO2
and money saved (compared to equivalent DOL)
* For details of FlashDrop, see user interfaces (page 28)
Feature Advantage Benefit
FlashDrop* Faster and easier drive set up and commissioning for Fast, safe and trouble-free method of programming available
volume manufacturing. Programming with no power. without powering up the drive - patented
Application macros Ready-made macros for common applications Fast single parameter set-up
Assistant control panel Two softkeys, function of which changes according to the Easy commissioning - Start-up assistant
state of the panel. Built-in “Help” button, giving User friendly maintenance - Maintenance assistant
programming hints. Real-time clock, allows timed tracing Rapid fault diagnosis - Diagnostic assistant
of faults and setting of parameters to activate functions at Quick access to all parameter changes - separate list
various times of day. Changed parameters menu also included
Clone drives Copy parameters from drives of differing rating or Easy to copy parameters to other drives, reducing
software versions commissioning times
Programmable customer 8-point load curve set during commissioning, with under Allows precise monitoring of changes in plant conditions
load curve and overload regions, as well as alarm conditions and early warning of potential problems
Brake chopper Built-in up to 11 kW Reduced cost
Swinging chokes Swinging DC chokes - matches the right inductance to the Reduces total harmonic distortion (THD)
right load, thereby suppressing and reducing harmonics emissions up to 25 percent, even at reduced load
EMC 1st and 2nd environment RFI filters as standard No need for additional external filtering
Fieldbus Built-in Modbus using RS 485 Reduced cost, full access to industrial networks
Optional plug-in fieldbus modules
Sensorless vector control Improved motor control performance Enables wider range of applications to be tackled
Low peak volts and du/dt Motor peak voltage and rate of rise meets IEC 60034-17 Kind to motor windings
RoHS compliance Compliance achieved during 2007 Environmentally friendly drives
For more details, please refer to Technical Catalogue 3AFE64792857
ABB general purpose drive l ABB drives and motors catalogue 2014 23
Main features
ABB general purpose drive0.75 kW to 355 kW, ACS550Motor control method - Scalar, vector speed and torque (open and closed loop)208/240 V, 3-phase supply, 0.75 kW - 75 kW
380/480 V, 3-phase supply, 0.75 kW - 355 kW
ABB general purpose drive
ACS550 – Variants, ratings, types, voltages and prices
Wall-mounted - 0.75 kW - 160 kW, 380/480 V – Wall-mounted, frame sizes R1-R6– IP21 as standard, IP54 as option– 55 percent size reduction at 160 kW– Built-in EMC filter– Standard software, easy to configure– Built-in Modbus interface– Cable connection box– Brake chopper in frame sizes R1-R2– Assistant control panel– Built-in patented swinging choke – Sensorless vector control, scalar control– FlashDrop compatible– RoHS compliant
Free-standing - 160 kW - 355 kW, 380/480 V– Free-standing, frame size R8– IP21 as standard, very compact design– Built-in EMC filter– Standard software, easy to configure– Built-in Modbus interface– Pedestal unit on wheels, easy handling– Assistant control panel– Sensorless vector control,
scalar control– Free-standing units are not
FlashDrop compatible– Not RoHs compliant – For dimensions and prices,
please contact ABB
Control panel Type Price
Assistant control panel ACS-CP-A £86**
** Price of control panel only when purchased with drive
ABB general purpose drive variants
24 ABB general purpose drive l ABB drives and motors catalogue 2014
Includes EMC Filter* Control panel is required for programming and set-up - see below† Heavy duty ratings available, when higher overload requirements are needed - contact ABB** R6a is not an official frame size, it just designates slightly different dimensions
† Ratings Frame Fuse Heat Cooling Type IP21 list IP54 list
Normal use A dissipation requirements (code shown is price without price without
PN I2N A Type gG W m3/h IP21, for IP54 control control
kW A add +B055) panel* panel*
1.1 3.3 R1 10 40 44 ACS550-01-03A3-4 £433 £513
1.5 4.1 R1 10 52 44 ACS550-01-04A1-4 £545 £603
2.2 5.4 R1 10 73 44 ACS550-01-05A4-4 £569 £635
3 6.9 R1 10 97 44 ACS550-01-06A9-4 £625 £681
4 8.8 R1 10 127 44 ACS550-01-08A8-4 £702 £793
5.5 11.9 R1 16 172 44 ACS550-01-012A-4 £850 £905
7.5 15.4 R2 16 232 88 ACS550-01-015A-4 £985 £1,063
11 23 R2 25 337 88 ACS550-01-023A-4 £1,198 £1,266
15 31 R3 35 457 134 ACS550-01-031A-4 £1,536 £1,671
18.5 38 R3 50 562 134 ACS550-01-038A-4 £1,997 £2,143
22 45 R3 50 667 134 ACS550-01-045A-4 £2,336 £2,448
30 59 R4 63 907 280 ACS550-01-059A-4 £2,841 £3,055
37 72 R4 80 1120 280 ACS550-01-072A-4 £3,291 £3,494
45 87 R4 125 1440 280 ACS550-01-087A-4 £4,068 £4,349
55 125 R5 160 1940 350 ACS550-01-125A-4 £4,810 £5,143
75 157 R6 200 2310 405 ACS550-01-157A-4 £5,171 £5,503
90 180 R6 250 2810 405 ACS550-01-180A-4 £6,579 £7,122
110 205 R6 250 3050 405 ACS550-01-195A-4 £7,940 £8,484
132 245 R6a** 315 3260 405 ACS550-01-246A-4 £9,752 £10,295
160 290 R6a** 315 3850 405 ACS550-01-290A-4 £11,523 £12,066
380/480 V, 3-phase supply voltage
Control panel for ACS550
208/240 V, 3-phase supply voltage3-phase 240 V is also available for customers supplying the North American market. Please enquire for details.
ABB HVAC drive l ABB drives and motors catalogue 2014 25
What is an ABB HVAC drive?The ABB HVAC drive, ACH550, is a complete dedicated low voltage AC drive especially for heating, ventilation & air-conditioning (HVAC) applications. The drives are designed to meet the HVAC market requirements including harmonics and EMC standards and for easy integration with building management systems straight out of the box. They feature built-in control programmes specifically designed for HVAC applications like cooling tower fans, supply and return fans, and booster pumps and condensers. With built-in PID control, native BACnet communication, timers, real-time clock and a calendar, ABB drives provide flexible solutions for a wide range of HVAC needs.
Where can it be used?ABB HVAC drives make maintaining a buildingscomfort zone easy, quick and energy efficient. The drivescontrol the speed of pump, fan and compressor motorsused in air handling units, cooling towers, chillers andother HVAC applications. They help reduce the HVAC system’s energy consumption by up to 70 percent, and quite often have payback times of less than a year. With more than 500,000 drives for HVAC installed globally, these highly reliable drives with built-in BACnet easily integrate into building management systems. The drives are stocked globally for quick delivery.
* For details of FlashDrop, see user interfaces (page 28)
Feature Advantage Benefit
Swinging choke Patented by ABB Reduces part load harmonics by up to 25 percent, in
Reduces the drives’ harmonic signature comparison with traditional chokes. Variable air volume (VAV)
systems run on partial loads at least 95 percent of the time
EMC (manufacturer’s Integrated category C2 EMC filters suitable for 400 V network connection
statement available) (1st environment) filters to BS EN 61800-3 built into the drive as standard will save panel space,
avoid additional wiring, earthing and assembly costs
Additional serial HVAC protocols built in as standard. Can connect to any building management system (BMS)
communications BACnet, Modbus RTU, FLN Apogee,
N2 Metasys, RS 485
Fieldbus adapter allows connection of: LonWorks, Profibus-DP,
CANopen, DeviceNet, Modbus/TCP, ControlNet, Ethernet
Real-time clock Easily set up at time of installation and protected by its own Can be used together with timer functions of the drive to trigger
battery back-up various events (via relays or outputs) within the application
software such as time / speed profile, allowing the drive to be a
stand-alone unit without the need for BMS input.
System diagnostics Diagnostic assistant, on board fault history with real time of Instant fault tracking and date stamping, gives status
when fault occurred, covering voltage, current, DC link level etc of drive to enable rapid drive diagnostics
Energy efficiency counters Works out energy savings of the application in kWh Can assist with electricity billing in accordance with Part L2
and MWh; the cost of the energy saved in a local Building Regulations. Allows verification of energy savings
currency; and the carbon dioxide (CO2) emissions before making investments in capital equipment
equivalent of the energy saved
Main features
Highlights– Easy ordering– Quick installation– Rapid start-up, trouble-free use, easy interfacing– Built in BACnet– Wide power range in wall-mounted IP21 and IP54 variants– Programmed with several HVAC applications, including
supply and return fans, cooling tower fans, booster pumps and condensers.
– Intelligent HVAC control panel with clear text– New energy monitoring features record energy, CO2
and money saved (compared to equivalent DOL)
For more details, please refer to Technical Catalogue 3AFE68295378
ABB drive for HVAC
0.75 kW to 355 kW, ACH550Motor control method - Scalar, vector speed and torque (open and closed loop)208/240 V, 3-phase supply, 0.75 kW - 75 kW
380/480 V, 3-phase supply, 0.75 kW - 355 kW
26 ABB HVAC drive l ABB drives and motors catalogue 2014
ACH550 – Variants, ratings, types, voltages and prices
Wall-mounted - 0.75 kW - 160 kW, 380/480 V, – Wall-mounted, frame sizes R1-R6– 2 variants, IP21 and IP54– 55 percent size reduction at 160 kW– Built-in EMC filter (1st & 2nd environment)– Standard software, easy to configure– Built-in BACnet and Modbus interfaces– Cable connection box– Brake chopper in frame sizes R1-R2– HVAC assistant control panel– Built-in patented swinging choke – Sensorless vector control, scalar control– FlashDrop compatible– RoHS compliant
Free-standing - 160 - 355 kW, 380/480 V– Free-standing, frame size R8– IP21 as standard, very compact design– Built-in EMC filter– Standard software, easy to configure– Built-in BACnet and Modbus interface– Pedestal unit on wheels, easy handling– HVAC assistant control panel– Sensorless vector control, scalar control– Free-standing units are not FlashDrop compatible– Not RoHs compliant – For dimensions and prices, please contact ABB
Control panel Type Price
Assistant control panel ACS-CP-A £POA
ABB HVAC drive variants
Includes EMC Filter* Control panel is required for programming and set-up - see below† Heavy duty ratings available, when higher overload requirements are needed - contact ABB** R6a is not an official frame size, it just designates slightly different dimensions
† Ratings Frame Fuse Heat Cooling Type IP21 list IP54 list
Normal use A dissipation requirements (code shown is price without price without
PN I2N A Type gG W m3/h IP21, for IP54 control control
kW A add +B055) panel* panel*
0.75 2.4 R1 10 30 44 ACH550-01-02A4-4
1.1 3.3 R1 10 40 44 ACH550-01-03A3-4
1.5 4.1 R1 10 52 44 ACH550-01-04A1-4
2.2 5.4 R1 10 73 44 ACH550-01-05A4-4
3 6.9 R1 10 97 44 ACH550-01-06A9-4
4 8.8 R1 10 127 44 ACH550-01-08A8-4
5.5 11.9 R1 16 172 44 ACH550-01-012A-4
7.5 15.4 R2 16 232 88 ACH550-01-015A-4
11 23 R2 25 337 88 ACH550-01-023A-4
15 31 R3 35 457 134 ACH550-01-031A-4
18.5 38 R3 50 562 134 ACH550-01-038A-4
22 45 R3 50 667 134 ACH550-01-045A-4
30 59 R4 63 907 280 ACH550-01-059A-4
37 72 R4 80 1120 280 ACH550-01-072A-4
45 87 R4 125 1440 280 ACH550-01-087A-4
55 125 R5 160 1940 350 ACH550-01-125A-4
75 157 R6 200 2310 405 ACH550-01-157A-4
90 180 R6 250 2810 405 ACH550-01-180A-4
110 205 R6 250 3050 405 ACH550-01-195A-4
132 245 R6a** 315 3260 405 ACH550-01-246A-4
160 290 R6a** 315 3850 405 ACH550-01-290A-4
Types, ratings and dimensions 380-480 V, 3-phase supply voltage
Control panel for ACS550
208/240 V, 3-phase supply voltage3-phase 240 V is also available for customers supplying the North American market. Please enquire for details.
Fo
r prices o
n in
du
stry specific p
rod
ucts p
lease con
tact
AB
B’s H
VAC
team
Fo
r prices o
n in
du
stry specific p
rod
ucts p
lease con
tact
AB
B’s H
VAC
team
ABB drive for HVAC
H2 H1
D
W
ABB general purpose drive and ABB HVAC drive
ACS550 and ACH550 – Dimensions, I/O and options
Typical control connections ACS550 and ACH550These connections are shown as examples only. Please refer to the User’s Manual – macro section, for more detailed information and for different I/O configurations.
Typical I/O connections ACS550
Other available options ACS550 and ACH550– IP54 protection class (frames R1-R6a)– Encoder feedback option available– For other options, please see the user interfaces on page 28
Typical I/O connections ACH550
Width (W) Height (H) Depth (D) Weight Brake unit
mm mm mm kg type code
150 500 347 7.5 ACS-BRK-C
270 600 450 20.5 ACS-BRK-D
H1 = Height with cable connection box
H2 = Height without cable connection box
W = Width D = Depth
ABB general purpose drive and HVAC drive l ABB drives and motors catalogue 2014 27
Frame IP21 / UL open IP54 / UL type 12
size H1 H2 W D Weight H W D Weight
mm mm mm mm Kg mm mm mm Kg
R1 369 330 125 212 6.5 449 213 234 8.2
R2 469 430 125 222 9 549 213 245 11.2
R3 583 490 203 231 16 611 257 253 18.5
R4 689 596 203 262 24 742 257 284 26.5
R5 739 602 265 286 34 776 369 309 38.5
R6 880 700 300 400 69 924 410 423 80
R6a 986 700 302 400 73 1119 410 423 84
Dimensions and weights
Frequency Resistor Continuous Max. Brake unit
converter ohm output output type code
input voltage W 20 s W
200 - 240 V AC 32 2000 4500 ACS-BRK-C
380 - 480 V AC 32 2000 12000 ACS-BRK-C
200 - 240 V AC 10.5 7000 14000 ACS-BRK-D
380 - 480 V AC 10.5 7000 42000 ACS-BRK-D
Brake units and choppers technical data Chopper dimensions
** R6a not an official frame size, shown here to highlight the slightly different dimensions of the largest rating
Ready
Running
Not fault
(other signalsconfigurable)
(NPN or PNP possible)
ACH550-01 User's Manual
1 SCR Signal cable shield (screen)
2 AI1 External reference 1: 0(2)…10 V or 0(4)…20 mA
3 AGND Analogue input circuit common
4 10V Reference voltage +10 V DC
5 AI2 Actual signal 1: 0(2)…10 V or 0(4)…20 mA 3
6 AGND Analogue input circuit common
7 AO1 Output frequency: 0(4)…20 mA
8 AO2 Output current: 0(4)…20 mA
9 AGND Analogue output circuit common
10 24V Auxiliary voltage output +24 V DC
11 GND Common for DI return signals
12 DCOM Digital input common for all
13 DI1 Start/Stop: Activation starts the drive
14 DI2 Not used
15 DI3 Constant speed 1 (par. 1202) 1
16 DI4 Start enable 1: Deactivation stops the drive 2
17 DI5 Not used
18 DI6 Not used
19 RO1C Relay output 1 (par. 1401)
Default operation
Ready => 19 connected to 21
20 RO1A
21 RO1B
22 RO2C Relay output 2 (par. 1402)
Default operation
Running => 22 connected to 24
23 RO2A
24 RO2B
25 RO3C Relay output 3 (par. 1403)
Default operation
Fault (-1) => 25 connected to 27
26 RO3A
27 RO3B
1 Not available if PID is activated2 Disable/enable with parameter 16083 The sensor for AI2 is powered externally (not shown in the figure). See the manufacturer’s
instructions. To use sensors supplied by the drive auxiliary voltage output, see page 120.Note: The drive starts only if possible protection functions (Run enable or Start enable 1 and 2) are activated from I/O or disabled with parameters.
1…10 kohm
HVAC defaultfor typical BMS applications
0...20 mAGround cable screen at sourcing end
DIP switchanalogue inputs
ABB general purpose drive and ABB HVAC drive
ACS550 and ACH550 – User interfaces
28 ABB general purpose drive and HVAC drive l ABB drives and motors catalogue 2014
ACS550 ACH550 Function
Start Hand Initiates operation of motor control
Stop Off Ceases operation of motor control
Up Up Changes parameters and their value/
increases reference
Down Down Changes parameters and their value/
decreases reference
Loc/Rem Auto Changes drive state from local/hand control
(control panel) to remote/auto control
(I/O or other external source)
HELP Built-in “Help” button
Softkey 1 Function changes according to state of panel
Softkey 2 Function changes according to state of panel
Relay extension (+L511)An extra 3 V free change-over relays can be added to the ACx550 by requesting an OREL module.
Panel mounting kit, IP54 and IP66The panel mounting kit enables mounting of control panels on cabinet doors. These kits include a 3 m extension cable, a gasket, mounting screws and a mounting template - two versions are now available, IP54 and IP66. The IP66 has an additional keypad membrane cover.
FlashDropA powerful palm-sized tool for fast and easy parameter setting, ideal for programming many drives. Programming in the box - unpowered. Ideal for OEMs as programming can be left until the moment before commissioning, or at the end of the production line, making it a safe option.
Fieldbus modules and fieldbusAn extensive range of fieldbus modules are available to allow connection to all the major industrial protocols. The drive has an RS485 Modbus interface built-in.
DriveWindow Light PC toolDriveWindow Light is a parameterisation and commissioning tool used to set-up and commission the drive. Monitoring and diagnostic facilities are included, as well as a local control panel. Wizards are included to guide the user through the most commonly performed tasks.
Local/Remote indicationMotor rotation indicator
Speed referenceActual value 1, Speed (selectable)Actual value 2, Output current (selectable)Actual value 3, Process value(selectable)
Softkey 2 function
Real time clock
Softkey 1 function
Overview of ACS550 and ACH550 interfaces
Analogue I/O
Digital inputs
Relay output extension option module (3 relays)
Encoder feedback option module(fits behind relay extension)
Relay outputs
Built-in Modbus using RS 485Built-in BACnet on ACH550
Plug-in fieldbus moduleDeviceNet LONWORKS® PROFIBUS DP CANopen ControlNet Ethernet and others
Assistant control panelFor easy drive programming, a detachable, multilingual alphanumeric Assistant control panel is offered as standard. The control panel has various assistants and a built-in help function to guide the user. It includes a real time clock, which can be used during fault logging and in controlling the drive, such as start/stop at certain times of the day. The control panel can be used for copying parameters for back-up or for downloading to another drive. A large graphical display and soft-keys make it extremely easy to navigate.
ACH550 keypad
ACS550 keypad
Hand/Auto indicationMotor rotation indicator
Example of a parameter nameExample of a parameter selection
Softkey 2 function
Real time clock
Softkey 1 function
ABB drive for water and wastewater
0.37 kW to 500 kW, ACQ810Motor control method – DTC200/480 V, 3-phase supply, 0.37 kW - 500 kW
What is an ABB drive for water and wastewater?The ABB industry-specific drive is designed for all of the applications commonly used in the water and wastewater industry. The specifically designed modules feature tailor-made pump control functions for single and multi-pump systems. These functions ensure smooth, disturbance-free operation of water and wastewater processes, maximising energy efficiency while reducing unnecessary downtime. The drives’ pump-specific functions decrease the lifecycle cost of the pumping system, helping to save time and money. The power range has now been expanded with the introduction of the G1 and G2 frame sizes.
Where can it be used? The ABB industry-specific drive module can be used for most of the variable-speed applications contained within the water and wastewater industry, to optimise the system and to save energy. The modules are designed for cabinet assembly and are easily mounted side-by-side. Intelligent start-up assistants ensure that drive commissioning is straightforward. The functions needed for most pumping systems can be easily implemented with the pre-programmed macros. Starting up a pumping system and optimising its performance is extremely easy. Highlights – Optimal pump control for various applications– Intelligent solution for controlling pump performance
– Remote monitoring and diagnostics– Pump auto change– Full multipump software now available– Flow measurement included in the product, ideal for leak
detection and a low cost– Anti-rag pump cleaning algorithms– Easy and cost-effective cabinet assembly– Rapid and simple pumping system start-up– Advanced energy efficiency in pumping systems– Maximised process uptime– Lifecycle support
Feature Advantage Benefit
Direct torque control Premium motor control platform Lower losses, improved energy saving
Soft pipe filling Provides a pump with a smooth build-up of flow in pipes This avoids pressure peaks and reduces the stresses on
weak or ageing water mains when demand changes
Pump cleaning Used in wastewater pumping stations to prevent pump and The function can be set to trigger against different commands
or anti-jam pipe clogging and expensive maintenance activities e.g on each pump start; on monitoring if the pump is becoming
blocked; in response to a digital input or PLC command. If the
pump cleaning function runs too often, an alarm is raised
Flow calculation The drive has a flow meter routine that very accurately Avoids the need for costly external flow meters and is
determines the flow rate within a process suitable for applications where the flow data is not needed for
invoicing purposes
Level control Used to effectively control the filling or emptying of water Fast-ramp starting creates a flush effect to keep pipes clear.
or wastewater storage tanks Users can define the “efficiency speed” based on the pumps
best efficiency point
Multi-pump control Optimal control of applications where several parallel pumps Maintains stable process conditions optimising the speed
are operated together and the required flow rate is variable and number of the pumps needed
Pump priority Optimal control of applications where the consumption rate Operate higher capacity pumps during daytime and smaller
varies based on demand units at night. This allows pumps to be operated closer to
their best efficiency point
Pump specific protection The protection functions indicate if the pre-defined process Underload and overload functions are pre-defined across the
features conditions change speed range at five distinct points. Belt breaks or dry sumps
can be detected
Safe torque-off TÜV certified safely to SIL3 Remove contactor from MCC
For further information, see Technical Catalogue 3AUA0000055685
Main features
ABB industry-specific drive for water and wastewater l ABB drives and motors catalogue 2014 29
30 ABB indusrty-specific drive for water and wastewater l ABB drives and motors catalogue 2014
ABB drive for water and wastewater
ACQ810 – Variants, ratings, types, voltages and prices
The ACQ810 is available in several frame sizes to optimise the packing density ensuring MCC cabinet line-ups are as compact as possible. Minimised MCC line-ups mean that compliant bids to the water industry are as small as possible whilst still complying with EMC and thermal requirements.Frame A and B – EMC external but plug-in, so no extra cabling required. Drives can be horizontally mounted for smaller compartments.
Light overload No overload use Max Frame Fuses Heat Cooling Type MCC IP20
PN I2N Icont. max output A dissipation requirements mounting Price
kW A A A †Type gG W m3/h kits
1.1 2.7 3 4.4 A 6 100 24 ACQ810-04-02A7-4 +J410
UL 3 3.6 5.3 A 6 106 24 ACQ810-04-03A0-4 +J410
1.5 3.5 4.8 7 A 10 126 24 ACQ810-04-03A5-4 +J410
2.2 4.9 6 8.8 A 10 148 24 ACQ810-04-04A9-4 +J410
3 6.3 8 10.5 A 16 172 24 ACQ810-04-06A3-4 +J410
4 8.3 10.5 13.5 B 16 212 48 ACQ810-04-08A3-4 +J410
5.5 11 14 16.5 B 20 250 48 ACQ810-04-11A0-4 +J410
7.5 14.4 18 21 B 25 318 48 ACQ810-04-14A4-4 +J410
11 21 25 33 C 25 375 142 ACQ810-04-021A-4 +J410
15 28 30 36 C 32 375 142 ACQ810-04-028A-4 +J410
18.5 35 44 53 C 50 541 200 ACQ810-04-035A-4 +J410
22 40 50 66 C 50 646 200 ACQ810-04-040A-4 +J410
30 53 61 78 D 63 840 290 ACQ810-04-053A-4 +J410
37 67 78 100 D 80 1020 290 ACQ810-04-067A-4 +J410
45 80 94 124 D 100 1200 290 ACQ810-04-080A-4 +J410
55 98 103 138 E0 125 1190 168 ACQ810-04-098A-4 +J410
75 138 144 170 E0 160 1440 405 ACQ810-04-138A-4 +J410
90 162 202 282 E 250 2310 405 ACQ810-04-162A-4 +J410
110 203 225 326 E 250 2810 405 ACQ810-04-203A-4 +J410
132 240 260 326 E 315 3260 405 ACQ810-04-240A-4 +J410
160 286 290 348 E 315 4200 405 ACQ810-04-286A-4 +J410
200 377 387 470 G1 ∆ 630 4403 1200 ACQ810-04-377A-4 +J410 +H381
250 480 500 560 G1 ∆ 800 5602 1200 ACQ810-04-480A-4 +J410 +H381
315 570 580 680 G1 ∆ 1000 6409 1200 ACQ810-04-570A-4 +J410 +H381
355 634 650 730 G1 ∆ 1000 8122 1200 ACQ810-04-634A-4 +J410 +H381
400 700 710 850 G2 ∆ 1250 8764 1200 ACQ810-04-700A-4 +J410 +H381
450 785 807 1020 G2 ∆ 1400 9862 1200 ACQ810-04-785A-4 +J410 +H381
500 857 875 1100 G2 ∆ 1400 10572 1420 ACQ810-04-857A-4 +J410 +H381
I2N - Nominal output current. 110% overload 1 min / 5 min. Icont - Continuous rms output current with no overload capacity UL = UL - NEMA rated motor - no IEC motor equivalent, however the current rating may be useful† For fuse selection, refer to the hardware manual, weak networks may require aR fuses∆ These fuses are aR type, gG fuses not recommended for this frame size
Frame C to E – EMC and harmonics choke built into the unit, so most compact size with no extra items to fit or cable.Frame G1 and G2 – New high power design, mounted on wheels for easy manual handling. Removeable cabling boxes ensure power cables are fitted only once.
To ensure A
BB
can tailor the d
rive to yo
ur needs, p
rice on ap
plicatio
n
380 to 480 V, 3–phase supply voltage
ABB drive for water and wastewater
ACQ810 – Dimensions, I/O and options
Dimensions and weights
NotesAll dimensions and weights are without options1) Height is the maximum measure without
clamping plates. In A and B frames the external C3 EMC-filter adds 160mm to the height. (The EMC filter does not have to be plugged in, it can be sited nearby) EMC-filter is internal in frames C, D, E0 and G
2) Total depth with control panel, 10mm less with keypad removed
1) 2) These notes do not apply to the G1 and G2 frames
Frame Height 1) Depth 2) Width Weight
size mm mm mm kg
A 364 219 94 3.3
B 380 297 101 5.4
C 567 298 166 15.6
D 567 298 221 21.3
E0 602 376 276 34
E 700 465 312 67
G 1,564 571 562 200
G1 1,462 (1,560) 505 (515) 305 (329) 161 (191)
G2 1,662 (1,710) 505 (515 305 (329) 199 (229)
( ) = Dimensions with optional cable boxes
Typical I/O connections
STO stands for safe torque-off and is certified by TÜV to SIL3 to IEC61508.
STO can be used to guarantee no mechanical rotation (no torque) at the shaft of the motor and thus allows MCC panels to be built without the need for the traditional contactor, where maintenance of the rotating machinery is a requirement.Electrical isolation will only be required for working on the drive or the electrical connections of the motor, so the traditional door isolator will suffice for that requirement.
ACQ810 main connections overview
H
D
W
Mains connection
24 V DC input
Relay outputs (2 x RO)
Analogue and digital extensions
Digital inputs (6 x D)
Digital inputs/outputs (2 x AO)
Analogue inputs (2 x A)
Analogue outputs (2 x AC)
Modbus/Drive-to-Drive link
Safe torque-off (STO)
User interface (PC tools, control panel)
Motor connection
Removable memory unit
Communication options
XPOWExternal power input24 V DC, 1.6 A
+24VI 1GND 2
XRO1, XRO2Relay output RO1 [Ready]250 V AC / 30 V DC2 A
NO 1COM 2NC 3
Relay output RO2 [Fault(-1)]250 V AC / 30 V DC2 A
NO 4COM 5NC 6
XD241DV42+*CD V 42+2DNGIDdnuorg tupni latigiD3DV42+*CD V 42+4DNGOIDdnuorg tuptuo/tupni latigiD1IArepmuj noitceles dnuorGXDI
11ID]tratS/potS[ 1ID tupni latigiDDigital input DI2 [Constant speed 1] DI2 2
33ID]teseR[ 3ID tupni latigiD44ID4ID tupni latigiD
Digital input DI5 [EXT1/EXT2 selection] DI5 5ALIID)potS = 0( kcolretni tratS
XDIODigital input/output DIO1 [Output: Ready] DIO1 1Digital input/output DIO2 [Output: Running] DIO2 2
XAI1FERV+)+( egatlov ecnerefeR2FERV-)–( egatlov ecnerefeR3DNGAdnuorG
Analogue input AI1 (Current or voltage, selectable by jumper AI1) [Current] [Speed reference 1]
AI1+ 4AI1- 5
Analogue input AI2 (Current or voltage, selectable by jumper AI2) [Current] [Process actual value 1]
AI2+ 6AI2- 7
1IArepmuj noitceles egatlov/tnerruc 1IA2IArepmuj noitceles egatlov/tnerruc 2IA
XAO
Analogue output AO1 [Current]AO1+ 1AO1- 2
Analogue output AO2 [Speed rpm]AO2+ 3AO2- 4
XD2DTrepmuj noitanimret
Drive-to-drive link.
Drive-to-drive linkB 1A 2
BGND 3XSTO
Safe torque-off. Both circuits must be closed for the drive to start.
OUT1 1OUT2 2
IN1 3IN2 4
Control panel connectionMemory unit connection
XPOWExternal power input24 V DC, 1.6 A
+24VI 1GND 2
XRO1, XRO2Relay output RO1 [Ready]250 V AC / 30 V DC2 A
NO 1COM 2NC 3
Relay output RO2 [Fault(-1)]250 V AC / 30 V DC2 A
NO 4COM 5NC 6
XD241DV42+*CD V 42+2DNGIDdnuorg tupni latigiD3DV42+*CD V 42+4DNGOIDdnuorg tuptuo/tupni latigiD1IArepmuj noitceles dnuorGXDI
11ID]tratS/potS[ 1ID tupni latigiDDigital input DI2 [Constant speed 1] DI2 2
33ID]teseR[ 3ID tupni latigiD44ID4ID tupni latigiD
Digital input DI5 [EXT1/EXT2 selection] DI5 5ALIID)potS = 0( kcolretni tratS
XDIODigital input/output DIO1 [Output: Ready] DIO1 1Digital input/output DIO2 [Output: Running] DIO2 2
XAI1FERV+)+( egatlov ecnerefeR2FERV-)–( egatlov ecnerefeR3DNGAdnuorG
Analogue input AI1 (Current or voltage, selectable by jumper AI1) [Current] [Speed reference 1]
AI1+ 4AI1- 5
Analogue input AI2 (Current or voltage, selectable by jumper AI2) [Current] [Process actual value 1]
AI2+ 6AI2- 7
1IArepmuj noitceles egatlov/tnerruc 1IA2IArepmuj noitceles egatlov/tnerruc 2IA
XAO
Analogue output AO1 [Current]AO1+ 1AO1- 2
Analogue output AO2 [Speed rpm]AO2+ 3AO2- 4
XD2DTrepmuj noitanimret
Drive-to-drive link.
Drive-to-drive linkB 1A 2
BGND 3XSTO
Safe torque-off. Both circuits must be closed for the drive to start.
OUT1 1OUT2 2
IN1 3IN2 4
Control panel connectionMemory unit connection
Typical STO and drive-to-drive link connections
ABB industriy-specific drive for water and wastewater l ABB drives and motors catalogue 2014 31
OptionsA number of control panel mounting options are available, to optimise MCC design. The drive is normally delivered with a control panel and holder fitted as standard. Other options include:- No control panel at all- Control panel door mounting kit- No cover at all for the drive unit- The new G1 and G2 frames can be ordered with cabling boxes
(providing surrounding) which allow easier module removalOther options for the ACQ810 include:- Analogue I/O extension module- Analogue and digital extension module- Relay I/O extension module- Extensive range of plug-in fieldbus modules- External du/dt filters if required
32 ABB industry-specific drive for water and wastewater l ABB drives and motors catalogue 2014
ABB drive for water and wastewater
ACQ810 – User interfaces
Assistant keypadFor easy drive programming, a detachable, multilingual alphanumeric Assistant control panel is preferred as standard. The control panel has various assistants and a built-in help function to guide the user. It includes a real-time clock, which can be used during fault logging and in controlling the drive, such as start/stop. The control panel can be used for copying parameters for back-up or for downloading to another drive. A large graphical display and softkeys make it extremely easy to navigate.
Name Function
Start Initiates operation of drive
Stop Ceases operation of drive
Up Changes parameters and their value/
increases reference
Down Changes parameters and their value/
decreases reference
Loc/Rem Changes drive state from local control
(control panel) to remote control
(I/O or other external source)
HELP Built-in “Help” button
Softkey 1 Function changes according to state of panel
Softkey 2 Function changes according to state of panel
Keypad door mounting platformDesigned to hold the keypad so that it can be attached to the MCC door. An IP54 variant is also available for higher IP requirements.
Removable memory unitThe memory unit stores the complete parameter and firmware set for the drive. Should a drive need to be replaced, swapping the memory unit to the new drive will transfer a complete drive set-up – absolutely no recommissioning is required.This reduces down time in the event of a problem.
Expansion for analogue and digital I/OAdditional I/O can be added to the ACQ810. This I/O can be addressed by the fieldbus so that the ACQ810 can be used as an I/O “nest”, or of course the I/O can be used to simply allow more connectability from the process to the drive, for example, flow or level transducers.
EMC filters – frames A and BPluggable EMC filters for frame sizes A and B can be plugged directly into the drive, or can be mounted next to the drive on the end of a plug and socket cable – easy to install and mount.
Fieldbus interfacesExtensive range of plug-in fieldbus interfaces, allowing connection to Profibus, DeviceNet, CanOpen, Modbus RTU and Ethernet.
DriveStudio PC toolDriveStudio is a parameterisation and commissioning tool used to set-up and commission the water and wastewater drive. Monitoring and diagnostic facilities are included, as well as a local control panel. Wizards are included to guide the user through the most commonly performed tasks.
DriveSPC PC toolDriveSPC (Solution Program Composer) allows access to the extended programming area of the ACQ810. Application specific IEC 61131 solution programmes can be generated and stored inside the drive. This way the drive can be tailored to the application and fully utilise the extended I/O.
Local/Remote indicationMotor rotation indicator
Speed referenceActual value 1, Speed (selectable)Actual value 2, Output current (selectable)Actual value 3, Process value(selectable)
Softkey 2 function
Real time clock
Softkey 1 function
ABB industrial drive l ABB drives and motors catalogue 2014 33
ABB industrial drive
0.55 kW to 2,800 kW, ACS800Motor control method - DTC208/240 V, 3-phase, powers dependent on range
380/415 V, 3-phase, powers dependent on range
380/500 V, 3-phase, powers dependent on range
525/690 V, 3-phase, powers dependent on range
What is an ABB industrial drive?ABB industrial drives are highly flexible AC drives that can be customised to meet the precise needs of many industrial applications. The drives cover a wide range of powers and voltages, including voltages up to 690 V. ABB industrial drives can be built in a number of differing formats: wall mounted, free standing, cabinet, industrial kits, multidrives or liquid cooled. This section describes the most popular styles. Page 41 describes other variants. Order-based customisation is an integral part of the offering.
Where can it be used?The ABB industrial drive is equipped with the premium motor control platform, DTC, and as such is ideally suited for the most demanding industrial applications, like high performance centrifuges as well as constant torque applications such as cranes, winders, hoists, extruders and heavy conveyors. Applications with high breakaway torque, like rubber mixers and highly precise applications like paper machines and engine dynamometers are easily handled. The drive has ATEX certification with ABB’s Ex d, Ex de, Ex nA and Ex tD motors and has marine certification for Lloyds, DNV and ABS.
Highlights– Build-to-order product can be tailored for the needs of
the application– Blanket ATEX certification (Ex) with ABB motors– Specialised software variants for selected applications– Adaptive programming - like having a small PLC inside – Common user and process interface with fieldbus – Common software tools for sizing and commissioning– 6-pulse, 12-pulse, low harmonic, 4Q, air-cooled,
water-cooled, flange mounting– Innovative hardware variants – DTC (direct torque control) superior motor performance– Flexibility to programme more advanced applications
Feature Advantage Benefit
Direct torque control Full torque at zero speed without encoder Consistently excellent performance ensures that drive is not
(DTC) Accurate speed and torque control the limiting factor in process
Built-to-order Customer can specify a wide range of options and Always meets application needs, tailored for the customer
build variants. Loaded with application specific software
Adaptive programming Small PLC inside your drive as standard. 15 programmable Needs no additional hardware or PC tool
function blocks. Up to 200 blocks by loading ‘multiblock’ Adapt the drive to the specific needs of the project
Dedicated software Industry specific software, fully researched, factory written Solve the application with very little effort
loading packages and fully supported e.g. crane, winder, winch etc
Application macros Popular I/O configurations, pre-written sets Fast settings for many applications
Brake choppers Brake chopper fits internally (smaller space) Reduced costs, high performance, internal monitoring
(where ordered) No additional space or installation time needed
Safe torque-off option TÜV approved safety feature SIL2/PL d Satisfies the need for latest machinery directive (when ordered)
Low peak volts and du/dt Motor peak voltage and rate of rise meets IEC 60034-17 Kind to motor windings
Compact size Contains EMC filter and harmonic chokes inside the drive No extra space or cabling is needed
Cooling fan Silent long-lifetime cooling fan that switches on and off Reduced maintenance, time and running costs
EMC 2nd environment RFI filters as standard No need for additional external filtering, additional space,
1st environment optional or additional cabling between drives and filter
Fieldbus gateway Snap-on module that is easily mounted inside drive Automation system independent of drive company
I/O Extensive and flexible standard and expansion I/O provides No need for additional space or cabling
additional analogue or digital connections
Start-up assistant Guides user through all essential settings without going Easy set-up of parameters, your own language,
to parameter list on-line info system always available
Huge range of Special variants for wall, cabinet mount, 4Q, low harmonic, There is always an ABB industrial drive variant that fits
hardware variants pre-built cabinets, drive kits, water-cooled the specification and requirements
Liquid cooled drives Most compact fully enclosed drive on the market Low losses to control room, low noise, totally enclosed
Fully certified for marine use for harsh environments
Main features
ABB industrial drive
ACS800 – Variants, ratings, types, voltages and prices
Wall-mounted single drivesSeries ACS800-01– 0.55 kW - 160 kW, (230 - 690 V)– 55 percent size reduction at 160 kW– IP21 as standard, IP55 as option– Wide range of built-in options– Optional cable box for SWA cables– Coated boards and internal I/O options– Built-in brake chopper– EMC filter for 1st environment, restricted distribution
according to EN 61800-3 - optional– EMC filter for 2nd environment, unrestricted distribution
according to EN 61800-3 - standard– Internal fieldbus options– ACS800-01 is type tested for marine applications– Blanket certification with ABB ATEX motors
† For fuse selection, refer to the hardware manual, weak networks may require aR fusesPrices include 2nd environment EMC filter and control panelOther ratings and voltages are available, 230 V, 500 V, 690 V. Price on applicationR6a frame denotes a slightly different physical dimension
For further information, see Technical Catalogue 3AFE 68375126 EN
34 ABB industrial drive l ABB drives and motors catalogue 2014
No-overload Light Heavy-duty Max Frame Fuse Heat Cooling Type IP21 IP55
use overload use output A dissipation requirements (+E200 to order Price Price
Pcont. max Icont. max PN IN Phd Ihd A †Type gG W m3/h EMC filter with with
kW A kW A kW A +E210 for R6 frame) keypad keypad
1.5 5.1 1.5 4.7 1.1 3.4 6.5 R2 10 100 35 ACS800-01-0003-3 £1,122 £1,318
2.2 6.5 2.2 5.9 1.5 4.3 8.2 R2 10 120 35 ACS800-01-0004-3 £1,167 £1,363
3 8.5 3 7.7 2.2 5.7 10.8 R2 10 140 35 ACS800-01-0005-3 £1,247 £1,443
4 10.9 4 10.2 3 7.5 13.8 R2 16 160 35 ACS800-01-0006-3 £1,415 £1,611
5.5 13.9 5.5 12.7 4 9.3 17.6 R2 16 200 35 ACS800-01-0009-3 £1,561 £1,757
7.5 19 7.5 18 5.5 14 24 R3 20 250 69 ACS800-01-0011-3 £1,745 £2,007
11 25 11 24 7.5 19 32 R3 25 340 69 ACS800-01-0016-3 £2,004 £2,266
15 34 15 31 11 23 46 R3 40 440 69 ACS800-01-0020-3 £2,329 £2,591
22 44 18.5 41 15 32 62 R4 50 530 103 ACS800-01-0025-3 £2,768 £3,116
30 55 22 50 18.5 37 72 R4 63 610 103 ACS800-01-0030-3 £3,163 £3,511
37 72 30 69 22 49 86 R5 80 810 250 ACS800-01-0040-3 £3,460 £3,833
45 86 37 80 30 60 112 R5 100 990 250 ACS800-01-0050-3 £4,180 £4,553
55 103 45 94 37 69 138 R5 125 1190 250 ACS800-01-0060-3 £4,911 £5,284
75 145 75 141 45 100 170 R5 160 1440 405 ACS800-01-0075-3 £5,271 £5,644
90 166 75 155 55 115 202 R6 200 1940 405 ACS800-01-0100-3 £6,698 £7,306
110 202 90 184 75 141 282 R6 224 2310 405 ACS800-01-0120-3 £7,923 £8,531
110 225 110 220 90 163 326 R6 250 2810 405 ACS800-01-0135-3 £8,061 £8,669
132 260 132 254 110 215 326 R6 315 3260 405 ACS800-01-0165-3 £9,871 £10,479
160 290 160 285 132 234 351 R6a 315 4200 405 ACS800-01-0205-3 £11,643 £12,251
380, 400 or 415 V, 3-phase supply voltage. The power ratings are valid at nominal voltage (400 V)
ABB industrial drive
ACS800-01 – Dimensions and options
H1 = Height with cable connection box H2 = Height without cable connection box R6a shown to highlight different dimensions only1) ACS800-01 without cable connection box does not fulfil
IP21 requirements
IP21 IP55
Options for ACS800-01ACS800-01 is a wall mounted drive, so the options fit inside:- IP55 variant- UK gland box to accommodate SWA cable- Different levels of EMC compliance- SIL2/PL d safe torque-off interface (unit mounts outside
the drive)- Coated boards- Extended warranty- Marine certification mounts and kits
All ABB industrial drives use the same common options and user interfaces. These are detailed on page 43.- The drive has two slots for I/O and fieldbus expansion and
one optical interface slot (an additional mother board can also be added – giving three more slots)
- I/O modules can be chosen from analogue expansion, digital expansion, encoder and resolver feedback options
- Fieldbus modules are always fixed to slot 1 and all of the major industrial fieldbus modules are available
H
D
W
H2 H1
D
W
ABB industrial drive l ABB drives and motors catalogue 2014 35
IP21 IP55
Frame H1 H2 W1 Depth Weight H W Depth Weight
size mm mm mm mm kg mm mm mm kg
R2 405 370 1) 165 226 9 528 263 241 16
R3 471 420 1) 173 265 14 528 263 273 18
R4 607 490 1) 240 274 26 774 377 278 33
R5 739 602 1) 265 286 34 775 377 308 51
R6 880 700 1) 300 399 67 923 420 420 77
R6a 977 700 1) 300 399 70 923 420 420 77
Dimensions and weights
- The drive can be ordered with specially designed application specific software variants. There are 17 variants available. For example, crane, master-follower, winder control, etc. The advantage of selecting these pre-written software variants, is that they have been written to cover the market requirements, they are tested and certified by the factory and come complete with a user manual and cabling instructions.
User interfacesPlease refer to page 43 for details of the ACS800 common user interfaces.
ABB industrial drive
ACS800 – Variants, ratings, types, voltages and prices
Single drive modules for cabinetsSeries ACS800-04 and ACS800-04M– Specifically designed for system integration– 0.55 kW - 1,900 kW (230 V - 690 V)– IP00 kits or IP20 modules depending on frame size – R1-R6 frames are back sheet mounted; R7 and R8 stands
on cabinet floor; R8i wheels into the cabinet– Easy access to power terminals: plug connections
on wheeled D4 and R8i units– Side-by-side mounting (excl. versions with side exit)– Extensive, programmable I/O with galvanically
isolated inputs– Three I/O and fieldbus extension slots inside– ACS800-04M can be ordered as disassembled kit of
parts to optimise the items purchased (R7 and R8 frames)– Rittal assembly kits available for easy cabinet integration– Service ‘skateboard’ for R7, R8 framesThe R7 and R8 modules are detailed below, please contact ABB for information on the other frame sizes shown here.
Options for ACS800-04When purchased as an ACS800-04, the kit always contains pedestal, busbars, power module, control module and keypad. If purchased as an ACS800-04(M) then it is possible to tailor the offering, remove busbars, have left or right handed or flat or bookcase orientation.
H
D
W
For further information, see Technical Catalogue 3AFE68404592
R6 R4 R3 R2 R7, R8 R8i
User interfacesPlease refer to page 43 for details of the ACS800 common user interfaces.
36 ABB industrial drive l ABB drives and motors catalogue 2014
No-overload Light Heavy-duty Max Frame Fuse Heat Cooling Type IP00
use overload use output A dissipation requirements (+E210, +J400 Price
Pcont. max Icont. max PN IN Phd Ihd A †Type gG W m3/h and +J410 to order with keypad*
kW A kW A kW A EMC and keypad)
110 206 110 202 90 163 326 R7 250 3000 540 ACS800-04-0140-3 £7,246
132 248 132 243 110 202 404 R7 315 3650 540 ACS800-04-0170-3 £8,799
160 289 160 284 132 240 432 R7 315 4300 540 ACS800-04-0210-3 £10,374
200 445 200 440 160 340 588 R8 500 6600 1220 ACS800-04-0260-3 £12,315
250 521 250 516 200 370 588 R8 630 7150 1220 ACS800-04-0320-3 £14,227
315 602 315 590 250 477 840 R8 630 8100 1220 ACS800-04-0400-3 £16,174
355 693 355 679 315 590 1017 R8 800 8650 1220 ACS800-04-0440-3 £18,346
400 720 400 704 355 635 1017 R8 800 9100 1220 ACS800-04-0490-3 £20,899
380, 400 or 415 V, 3-phase supply voltage. The power ratings are valid at nominal voltage (400 V)
† R7 module only 250mm wide, R8 module only 350mm wide
Bookshelf mounting Flat-type mounting
Frame H W D Weight H W D Weight
size mm mm mm kg mm mm mm kg
R7 1121 427† 473 100 1152 632 259 100
R8 1564 562† 568 205 1596 779 403 205
Dimensions and weights
Other ratings and voltages available on application, 230 V, 500 V, 690 VDrive can be purchased pre-assembled or as a disassembled kit, where parts can be omitted for cost optimisation by panel builders (R7, R8 frames)
Price includes 2nd environment EMC filter, control panel and door mounting kitMultiple control panel mounting options - please ask. * Comes with keypad and a door mount kit (+J400, +J410)† For fuse selection, refer to the hardware manual. Weak networks may require aR fuses
380, 400 or 415 V, 3-phase supply voltage. The power ratings are valid at nominal voltage (400 V)
Dimensions and weights
ABB industrial drive
ACS800 – Variants, ratings, types, votages and prices
Other ratings and voltage ranges available, 230 V, 500 V, 690 V. Price on applicationIncludes 2nd environment EMC filter and control panel and can include many other factory fitted options† For fuse selection, refer to the hardware manual
Cabinet-built drives (air- and liquid-cooled)Series ACS800-07– 45 kW - 2,800 kW, (380 - 690 V)– IP21 as standard, IP22, IP42, IP54 and IP54R as options– Up to 500 kW based on a single module including rectifier
and inverter– Above 500 kW separate rectifier and inverter modules
that have plug-in power connectors for easy maintenance and redundancy. Modules wheel-in and -out of cabinet
– 6- or 12-pulse operation as standard (>500 kW)– Extremely compact, internal swinging gate for
control options– Factory-built cabinet with EMC and thermally type-tested
for trouble-free operation– Extensive range of standard options– ATEX approved PTC interfaces and blanket certification
with ABB motors– TÜV approved emergency stopping options
The ACS800-07 cabinet drive range covers an extensive power and options range. The drives shown in the table are for the basic IP21 build format and only up to 400 kW. Please contact ABB to discuss the exact requirements of your factory built and certified cabinet, to ensure all relevant options are catered for.
Liquid-cooled optionACS800-07 can also be supplied in a liquid cooled format, ACS800-07LC, please refer to page 41 for details.
AB
B p
anels can be o
rdered
with a w
ide rang
e of
standard
op
tions.
Price o
n app
lication
For further information, see Technical Catalogue 3AFE68375126
ABB industrial drive l ABB drives and motors catalogue 2014 37
No-overload Light Heavy-duty Max Frame Fuse Heat Cooling Type Price
use overload use output A dissipation requirements
Pcont. max Icont. max PN IN Phd Ihd A † Type aR W m3/h
kW A kW A kW A
75 145 75 141 45 100 170 R5 315 1440 405 ACS800-07-0075-3
90 166 75 155 55 115 202 R6 315 1940 405 ACS800-07-0100-3
110 202 90 184 75 141 282 R6 400 2310 405 ACS800-07-0120-3
110 214 110 220 90 163 326 R6 500 2570 405 ACS800-07-0135-3
132 260 132 254 110 215 326 R6 550 3260 405 ACS800-07-0165-3
160 290 160 285 132 234 351 R6 550 4200 405 ACS800-07-0205-3
200 445 200 440 160 340 588 R8 800 6600 1220 ACS800-07-0260-3
250 521 250 516 200 370 588 R8 1000 7150 1220 ACS800-07-0320-3
315 602 315 590 250 477 840 R8 1250 8100 1220 ACS800-07-0400-3
355 693 355 679 315 590 1017 R8 1400 8650 1220 ACS800-07-0440-3
400 720 400 704 355 635 1017 R8 1400 9000 1220 ACS800-07-0490-3
380, 400 or 415 V, 3-phase supply voltage. The power ratings are valid at nominal voltage (400 V)
ABB industrial drive
ACS800-07 – Dimensions and options
Options for ACS800-07ACS800-07 is a cabinet drive, so its options fit inside the cabinet. The cabinet drive can be fitted with:- IP21, 22, 42, 54, 54R variants (no IP55)- Emergency stop variants, TÜV approved- Motor thermistor relays- ATEX-approved motor protection- Marine construction- UL approved components- Various types of cable markings, cabinet heaters, door
furniture and lighting etc.- Sine filter fitted to output (for older motors)- Top or bottom cable entry for either motor or power cables- UK gland plates for SWA cables- 110 V control inside the cabinet- Different levels of EMC compliance- Extended warranty- Additionally, ABB can accommodate any specialised option
or feature by using its in-house application design team
ACS800-07 also comes with options that are fitted to the drive module which is inside the cabinet:- SIL2 safe torque-off interface- Coated boards
ACS800-07 can be supplied with an extensive range of standard cabinet options. Contact your ABB representative for details*some of these options alter the cabinet dimensionsHigher power standard and bespoke cabinets can be quoted on request
H
D
W
User InterfacesAll ACS800s use the same common options and user interfaces. These are detailed on page 43- The drive has two slots for I/O and fieldbus expansion and
one slot for an optical interface (an additional mother board can also be added – giving three more slots)
- I/O modules can be chosen from analogue expansion, digital expansion, encoder and resolver feedback options
- Fieldbus modules are always fixed to slot 1 and all of the major industrial fieldbus modules are available
- The drive can also be ordered with specially designed application specific software variants. There are 11 variants available, for example, crane, master follower, winder control, etc. The advantage of selecting these pre-written software variants is that they have been written to cover the market requirements, they are tested and certified by the factory, and come complete with a user manual and cabling instructions.
38 ABB industrial drive l ABB drives and motors catalogue 2014
Larger powers are built with D4 and R8i modules. Ratings and dimensions available on request.
Frame *Width Height Height Depth *Depth top Weight (kg)
size with fuse IP IP54 entry/exit with line
switch 21/22/42 fuse switch
R5/R6 430 2130 2315 645 646 300
R8 830 2130 2315 646 646 500
Dimensions and weights, cabinet built (air-cooled)
ABB industrial drive
ACS800 – Variants, ratings, types, voltages and prices
6 pulse rectifier 12 pulse rectifier 18 pulse rectifier Active rectifier
Transformer and cabling Transformer and cabling Transformer and cabling Transformer and cabling simple complicated complicated simple
Current very distorted > THDI 30% Current distorted > THDI 12% Current wave form good > THDI 6% Current wave form best < THDI 4%
Alternatives in reducing line harmonics
Low harmonic, active rectifier drivesWall-mounted and cabinet-built A dedicated range of low harmonic drives based on active rectifier technology. No regenerative capability ensures no mistakes on generator supplies, still retaining a low 2-4 percent total harmonic distortion (THD) signature.
Series ACS800-31, wall-mounted– 5.5 kW - 110 kW (230 - 690 V)– IP21 as standard– Single package for easy cabinet installation,
reducing installation time and cabinet space
Series ACS800-37, cabinet-built– Power range from 37 kW to 2700 kW (230 to 690 V)– IP21 as standard; IP22, IP42, IP54 and IP54 R available as
options– Wheel-out power modules for improved manual handling– Plug-in power connectors for easy maintenance and
redundancy– Power module redundancy for improved availability– Factory-built cabinets ensure good installation
The R5 and R6 modules are detailed below. Please contact ABB if you require higher powers. Also, fully regenerative products are available called ACS800-11 and ACS800-17. Please refer to page 41 for more information.
Other ratings and voltage ranges available, 230 V, 500 V, 690 V. Price on application. Price includes 2nd environment EMC filter and control panelPrices for low harmonic cabinet drives ACS800-37 also available on application† For fuse selection, refer to the hardware manual. Weak networks may require aR fuses
No-overload Light Heavy-duty Max Frame Fuse Heat Cooling Type IP21
use overload use output A dissipation requirements (+E200 to order Price
Pcont. max Icont. max PN IN Phd Ihd A †Type gG W m3/h the EMC filter) with
kW A kW A kW A keypad
15 34 15 32 11 26 52 R5 40 550 350 ACS800-31-0016-3 £4,119
18.5 38 18.5 36 15 34 61 R5 40 655 350 ACS800-31-0020-3 £4,616
22 47 22 45 18.5 38 68 R5 50 760 350 ACS800-31-0025-3 £5,245
30 59 30 56 22 45 90 R5 63 1000 350 ACS800-31-0030-3 £6,012
37 72 37 69 30 59 118 R5 80 1210 350 ACS800-31-0040-3 £7,081
45 86 45 83 30 65 137 R5 100 1450 350 ACS800-31-0050-3 £8,405
55 120 55 114 45 88 168 R6 125 1750 405 ACS800-31-0060-3 £9,631
75 150 75 143 55 117 234 R6 160 2350 405 ACS800-31-0070-3 £11,198
90 165 75 157 75 132 264 R6 200 2800 405 ACS800-31-0100-3 £12,864
For further information, see Technical Catalogue 3AFE68375126
R5 R6
ABB industrial drive l ABB drives and motors catalogue 2014 39
Low harmonic, wall-mounted drives - ACS800-31380, 400 or 415 V, 3-phase supply voltage. The power ratings are valid at nominal voltage (400 V)
ABB industrial drive
ACS800-31 – Dimensions and options and ACS800-37 options
Frame Height Width Depth Weight
size mm mm mm kg
R5 816 265 390 62
R6 970 300 440 100
Dimensions and weights, ACS800-31
Options for ACS800-31, wall-mounted- UK gland box to accommodate SWA cable- Different levels of EMC compliance- SIL2 safe torque-off interface (unit mounts outside
the drive)- Coated boards standard- Extended warranty- Marine certification mounts and kits
Options for ACS800-37, cabinet-builtBeing cabinet drive, all of the options available for ACS800-31 are also valid, as they fit inside the cabinet. Additionally the cabinet drive can be fitted with:- IP21, IP22, IP42, IP54, IP54R variants (no IP55)- Emergency stop variants- Motor thermistor relays- ATEX-approved motor protection- Marine construction- UL approved components- Various types of cable markings, cabinet heaters, door
furniture and lighting etc.- Sine filter fitted to output (for older motors)- Top or bottom cable entry for either motor or power cables- UK gland plates for SWA cables- 110V control inside the cabinet- Additionally, ABB can accommodate any specialised option
or feature, by using its in-house application design team
ACS800-37 also comes with options that are fitted to the drive module which is inside the cabinet- SIL2/PL d safe torque-off interface- Coated boards
H
D
W
Height includes cable box, one enclosure, no external items
User interfacesAll ACS800s use the same common options and user interfaces, these are detailed on page 43.- The drive has two slots for I/O and fieldbus expansion and
one slot for an optical interface (an additional mother board can also be added – giving three more slots)
- I/O modules can be chosen from analogue expansion, digital expansion, encoder and resolver feedback options
- Fieldbus modules are always fixed to slot one, and all of the major industrial fieldbus modules are available
- The drive can also be ordered with specially designed application specific software variants. There are 11 variants available in all, for example, crane, master follower, winder control, etc. The advantage of selecting these pre-written software variants is that they have been written to cover the market requirements. They are tested and certified by the factory and come complete with a User Manual and cabling instructions.
40 ABB industrial drive l ABB drives and motors catalogue 2014
Ratings and dimensions for larger variants available on request.
Other ABB industrial drive variants
Regenerative, active rectifier drives Series ACS 800-11, wall-mounted– 5.5 kW to 110 kW (230 - 690 V)– IP21 as standard– Active rectifier unit– Single package for easy cabinet installation, reducing installation
time and cabinet space
Series ACS800-17, cabinet-built– 45 kW - 2,500 kW (230 - 690 V)– IP21 as standard, IP22, IP42, IP54 and IP54 R available as
options– Wheel-out power modules for improved manual handling– Plug-in power connectors for easy maintenance and redundancy– Power module redundancy for improved availability– Factory-built cabinets ensure good installation and compliance
with standards– ATEX approved PTC interfaces and blanket certification with
ABB motors
Regenerative, active rectifier drive modules - low harmonicSeries ACS800-14– 75 kW - 1,700 kW (380 - 690 V)– IP00 kits– Assembly kits for Rittal cabinets and generic cabinets– Separate controllers for galvanic isolation– Requires a separate +24 V DC supply at 3 A– Active supply unit can be configured for low harmonic mode (2-4
percent harmonic distortion) or regenerative mode, for better dynamic performance
– Comprehensive installation instructions and CAD drawings
Liquid cooled modulesSeries ACS800-x04LC– Extremely compact size, compared to air-cooled– 98 percent of drive losses transferred to liquid - removes the need
for air conditioned control rooms– Tested electrical/mechanical kits available - which make different
solutions easy to build– ACAD, PDF and full 3D ePLAN® modelling support – Pre-designed mounting frames available to reduce design time– Liquid / liquid-heat exchanger assemblies can be supplied by ABB– Module features: – Diode supply modules include line side chokes – Inverter modules include du/dt filters – Easy structure, fewer components – Inverter units, IGBT supply units and dynamic braking units are
based on one common R8i module
For further information see Technical Catalogue 3AFE 68375126
For further information see Technical Catalogue
3AFE 68404592
6 pulse rectifier 12 pulse rectifier 18 pulse rectifier Active rectifier
Transformer and cabling Transformer and cabling Transformer and cabling Transformer and cabling simple complicated complicated simple
Current very distorted > THDI 30% Current distorted > THDI 12% Current wave form good > THDI 6% Current wave form best < THDI 4%
Alternatives in reducing line harmonics
For further information see Technical Catalogue 3AFE68404592
Inverter
Diode
Other industrial drives from ABB l ABB drives and motors catalogue 2014 41
42 Other industrial drives from ABB l ABB drives and motors catalogue 2014
Other ABB industrial drive variants
MultidrivesA multidrive is a custom-made cabinet to suit a larger application or a process line. The cabinet contains multiple inverter stages of differing size, supplied from a common DC bus. The DC bus can be provided by a selection of supply units, diode, thyristor or IGBT (active supply unit).
Series ACS800 multidrive cabinets– 1.5 kW - 5,600 kW, 380 - 690 V– IP21 as standard, IP22, IP42 and IP54 as option– Smaller power modules have high packing density, using a
patented mounting arrangement– Power modules on wheels for easy manual handling– Plug-in power connectors for easy maintenance and
redundancy– Wide range of built-in options, including brake choppers, EMC
filters, fuse switches, contactors, communication options etc– ATEX approved PTC interfaces and blanket certification with
ABB motors– TÜV approved emergency stops
Series ACS800 multidrive modules– A range of IP20 module and IP00 kits to generate bespoke
multidrive systems built into system integrators own panels– Modules have no rectifiers, they are inverters only and range in
frames from R2i to R8i (i=inverter only)– Selection of rectifiers available to generate DC link for system.
Diode, thyristor or active rectifier are available– Cabinet kits for Rittal and generic, ensure easy integration– ACAD, PDF and full 3D ePLAN® modelling support
Liquid-cooled drivesSeries ACS800 - 17LC and ACS800 - 37LC– 37 kW - 2,700 kW, (380-690 V)– IP42 as standard, IP54 as option– ACS800 - 17LC, fully regenerative, ACS800 - 37LC, low harmonic– Provides reliable operation in adverse conditions– Silent and safe operation without the need for air ventilation or
air conditioning, fully enclosed cabinets, smaller than previous generation
– Extensive range of cabinet options, including water pumping and heat exchanger cabinets
– Marine enclosure available– Parallel modules allow redundant configuration– Ideal where space is limited, in harsh environments, or at sites
that require quieter operation, in applications where cooling water is freely available
– IEC, UL, CSA, Lloyds, DNV, ABS approvals– ATEX-approved PTC interfaces and blanket certification with
ABB motors
For further information see ACS800 Technical Catalogue 3AFE 68248531
For further information see Technical Catalogue 3AFE68404592
For further information see Technical Catalogue 3AFE68375126
ABB Industrial drive l ABB drives and motors catalogue 2014 43
Typical I/O and control connectionsThe ABB industrial drive family uses the same control card, keypad and software structure throughout its entire range. Analogue and digital I/O channels are used for different functions such as control, monitoring and measurement purposes (e.g. motor temperature). In addition, optional I/O extension modules are available providing additional analogue or digital I/O connections.
Below are the standard drive control I/O of the ABB industrial drive with factory macro. For other ACS800 application macros the functions may be different. Please refer to the firmware manual for details.
Reference voltage -10 VDC,
RL > 1 kohm
Reference voltage 10 VDC, RL > 1 kohm
Speed reference 0(2) ... 10 V, Rin > 200 kohm
By default, not in use. 0(4) ... 20 mA, Rin = 100 ohm
By default, not in use. 0(4) ... 20 mA, Rin = 100 ohm
Motor speed 0(4)...20 mA = 0...motor nom. speed, RL < 700 ohm
Output current 0(4)...20 mA = 0...motor nom. current, RL < 700 ohm
Stop/StartForward/Reverse
By default, not in use.
Acceleration & deceleration selectConstant speed selectConstant speed select
+24 V DC max. 100 mA
Digital groundDigital groundStart interlock (0 = stop)Power supply
Auxiliary power supply output, non-isola-ted, 24 V DC 250 mA
Relay output 1: ready
Relay output 2: running
Relay output 3: fault (-1)
^
^
VREF-
AGND
VREF+
AGND
AI1+
AI1-
AI2+
AI2-
AI3+
AI3-
AO1+
AO1-
AO2+
AO2-
DI1
DI2
DI3
DI4
DI5
DI6
+24VD
+24VD
X20
1
2
X21
1
2
3
4
5
6
7
8
9
10
11
12
X22
1
2
3
4
5
6
7
8
9
10
11
X23
1
2
X25
1
2
3
X26
1
2
3
X27
1
2
3
A
rpm
ABB industrial drive
ACS800 – Common user interfaces
Control panel The control panel features a full-text multilingual display. Dedicated keys allow fast access to actual signals, parameters, assistant functions and drive information. The panel can be used for parameter copying and for configuring adaptive programmes, working as a PLC inside the drive. Local motor control and parameter copying is also possible.
Panel mounting kitsKits are available that allow mounting on the cabinet door, or in a holder inside the cabinet. The panel can be screwed to the cabinet door, without the need for an additional holder.
FieldbusThe ACS800 supports an extensive list of fieldbus modules for connectivity to industrial networks.
I/O expansionACS800 can be fitted with a large range of analogue and digital I/O modules to expand its I/O capability.
DriveWindow - PC ToolDriveWindow is a high specification, high speed commissioning, maintenance and monitoring tool for the ACS800 drive range. It operates over an optical fibre link. (Drive requires an RCDO module)
DriveAP - PC ToolDriveAP allows access to the ACS800 adaptive, block programming environment.
Next generation of ABB industrial drive
What is the next generation ABB industrial drive?The highly successful ACS800 range of drives have been completely redesigned and updated to form the next generation all-compatible range. The drive contains a new harmonised parameter set, taking its features from all of the best functions within the existing ABB drive’s family, making it process compatible. The drive is programmed by the most intuitive and user-friendly keypad ABB has produced to date. A new PC tool is designed to incorporate all of the latest functionality that new operating systems bring, including a free-of-charge entry level version, making it compatible with all user types. The drive also contains the very latest 4th generation DTC motor control core, making the drive all compatible with any motor available in the market today including asynchronous, permanent magnet and synchronous reluctance (SynRM) are all controllable by the same software platform. Energy saving functions make it environmentally compatible.
44 ABB next generation industrial drive l ABB drives and motors catalogue 2014
0.55 kW to 2800 kW, ACS880Motor control method – DTC or Scalar208 / 240 V, 3-phase supply, powers dependent on range
380 / 415 V, 3-phase supply, powers dependent on range
380 / 500 V, 3-phase supply, powers dependent on range
525 / 690 V, 3-phase supply, powers dependent on range
Main features
Feature Advantage Benefit
Direct torque control Full torque at zero speed without encoder Consistently excellent performance ensures that drive is not
(DTC) Accurate speed and torque control the limiting factor in the process
Intuitive modern keypad High contrast, high definition display giving intuitive access Easy commissioning, programming,
to the drive parameters maintenance and fault finding
Start-up assistant Guides user through all essential settings without going Easy set-up of parameters, your own language,
to parameter list on-line information system always available
Removable memory unit Programme, parameter edits, motor calibrations and fault Zero re-commissioning in case of drive failure,
histories stored in the removable memory unit just move the memory unit, very short MTTR
Integrated, patented, No need to use external programmable safety hardware Minimise installation time and space. Shorter design
TÜV approved safety for drive specific functions. The module carries out drive times using TÜV approved module. Drive specific safety
module option specific safety functionality more efficiently than external functions save time and money as they are built in, and do
programmable devices, as they are designed to work not require additional speed monitoring devices to operate
directly with the drive. Patented safety monitoring functions
allow the drive to undertake speed related safety functions
with no additional speed feedback devices needed
Modern PC tools Entry level (FOC) and pro level PC tools are available for Keep copies of the parameters for back-up. Use the PC
commissioning, tuning, parameter management tools to optimise the application
and monitoring
Fieldbus gateway Snap-on module that is easily mounted inside drive Access to all major automation platforms
I/O extension modules Additional I/O can be added to the drive Easy addition of extra I/O to allow the drive to control the
application properly
Speed feedback modules A large array or high performance speed feedback devices Higher performances can be achieved or
can be interfaced to the drive via these modules position control can be undertaken
Energy monitoring and Drive controls the motor voltage dependant on the load. Consumed energy optimised across the speed
optimising features Drive monitors the saved energy compared to equivalent and load range. Energy savings presented in local currency
DOL operation and tonnes of CO2
Drive-to-drive link Built-in industrial control link Built-in ability to undertake master-follower applications with
no extra hardware
Next generation of ABB industrial drive
ABB next generation industrial drive l ABB drives and motors catalogue 2014 45
What is the next generation ABB drive? (cont)The drive contains energy saving features like speed controlled cooling fans, energy optimising and monitoring software, making the drive compatible with the environment as well.
New innovations include built-in machinery safety functionality such as safe torque-off (STO) to SIL 3 PL e as standard. Other more complicated solutions can be realised with the plug-in safety functions module (see page 53 for more details). As with the existing ABB industrial drive range the next generation drives can be built in a number of differing formats: wall mounted, modules for cabinet installation, cabinets, industrial kits or multidrives. The range is growing as ABB increases this product offering, so please ask which variants are available to ensure the range covers your requirements. Meanwhile, the existing ABB industrial drive will remain in production for some years ahead.
Where can it be used?The next generation ABB industrial drive is equipped with the 4th generation premium motor control platform, DTC, and as such is ideally suited for the most demanding industrial applications. Constant torque and torque at zero speed is perfect from the DTC core.
Suitable applications include cranes, winders, hoists,
extruders and heavy conveyors. Applications with high breakaway torque, like rubber mixers and highly precise applications like paper machines and engine dynamometers are easily handled. The new motor control platform also allows control of every major AC motor type (including SynRM), so many and varied applications are possible.
Highlights – ACS880– Built to order product can be tailored for the needs of the
application– Highly intuitive high contrast and high resolution keypad
suitable for gloved hands– Built-in safety functionality to satisfy the demands of IEC
62061 and ISO 13849-1– Removable memory unit– Flexibility to programme more advanced applications– Common user and process interface with fieldbus – Common software tools for sizing and commissioning– Innovative hardware variants – DTC (direct torque control) superior motor performance– Energy efficiency counters– Energy optimiser – optimises the motor control for the
application– Load analyser for optimised dimensioning of the drive,
motor and process
Next generation of ABB industrial drive
Wall-mounted single driveSeries ACS880-01– 0.55 kW - 250 kW, (208 - 690 V)– Largest power wall-mounted drive on market– Coated boards as standard– TÜV approved safe torque-off (STO) to SIL 3 PL e standard– IP21 as standard, IP55 as option– IP55 variant same footprint as IP21 variant– Brake chopper standard to R4 frame, option thereafter– Wide range of built-in options– Optional UK cable box option for SWA cables– EMC filter for C3 category according to EN 61800-3 (2004)
standard – category C2 optional– Internal fieldbus options– Optional safety module– Optional I/O expansion– ACS880 user interfaces described later
46 ABB next generation industrial drive l ABB drives and motors catalogue 2014
ACS880 – Variants, ratings, types, voltages and prices
For further information, see Technical Catalogue 3AUA0000098111
*130% overload, **125% overload† For fuse selection, refer to the hardware manual. Weak networks may require aR fuses∆ These fuses are aR fuses, ABB does not recommend gG fuses on these larger drivesNote: Current rating match IE3 motor nameplatesNote: Prices include keypad, EMC filter and SWA gland plates and full manuals
380 to 415 V, 3-phase supply voltage. The power ratings are valid at nominal voltage (400 V)
No-overload Light-duty Heavy-duty Max Frame Fuse Heat Cooling Type Price Price
(nominal) use use use output A dissipation requirements (+ E200, + R700 + IP21 IP55
PN IN PLd ILd Phd Ihd A † Type gG W m3/h H358 to order EMC (+B056)
kW A kW A kW A & SWA gland plate)
0.75 2.4 0.75 2.3 0.55 1.8 3.1 R1 4 30 44 ACS880-01-02A4-3 £821 £962
1.1 3.3 1.1 3.1 0.75 2.4 4.1 R1 6 40 44 ACS880-01-03A3-3 £861 £1,002
1.5 4.0 1.5 3.8 1.1 3.3 5.6 R1 6 52 44 ACS880-01-04A0-3 £891 £1,081
2.2 5.6 2.2 5.3 1.5 4.0 6.8 R1 10 73 44 ACS880-01-05A6-3 £1,021 £1,211
3.0 8 3.0 6.8 2.2 5.6 9.5 R1 10 94 44 ACS880-01-07A2-3 £1,071 £1,261
4.0 10 4.0 8.9 3.0 7.2 12.2 R1 16 122 44 ACS880-01-09A4-3 £1,201 £1,391
5.5 12.9 5.5 12.0 4.0 9.4 16 R1 16 172 44 ACS880-01-12A6-3 £1,431 £1,621
7.5 17 7.5 16 5.5 12.6 21 R2 25 232 88 ACS880-01-017A-3 £1,517 £1,707
11 25 11 24 7.5 17 29 R2 32 337 88 ACS880-01-025A-3 £1,937 £2,191
15 32 15 30 11 25 42 R3 40 457 134 ACS880-01-032A-3 £2,217 £2,471
18.5 38 18.5 36 15 32 54 R3 50 562 134 ACS880-01-038A-3 £2,377 £2,631
22 45 22 43 19 38 64 R4 63 667 200 ACS880-01-045A-3 £2,703 £3,040
30 61 30 58 22 45 76 R4 80 907 200 ACS880-01-061A-3 £2,853 £3,190
37 72 37 68 30 61 104 R5 100 1117 280 ACS880-01-072A-3 £3,534 £3,896
45 87 45 83 37 72 122 R5 100 1120 280 ACS880-01-087A-3 £4,294 £4,656
55 105 55 100 45 87 148 R6 125 1295 435 ACS880-01-105A-3 £4,661 £5,023
75 145 75 138 55 105 178 R6 160 1440 435 ACS880-01-145A-3 £5,171 £5,533
90 169 90 161 75 145 247 R7 ∆ 315 1940 450 ACS880-01-169A-3 £6,811 £7,173
110 206 110 196 90 169 287 R7 ∆ 315 2310 450 ACS880-01-206A-3 £7,051 £7,641
132 246 132 234 110 206 350 R8 ∆ 350 3300 550 ACS880-01-246A-3 £9,009 £9,599
160 293 160 278 132 246* 418 R8 ∆ 400 3900 550 ACS880-01-293A-3 £11,189 £11,779
200 363 200 345 160 293 498 R9 ∆ 550 4800 1150 ACS880-01-363A-3 £13,815 £14,496
250 430 250 400 200 363** 545 R9 ∆ 630 6000 1150 ACS880-01-430A-3 £16,815 £17,496
Options for ACS880-01ACS880-01 is a wall-mounted drive, so all of the options fit inside: – IP55 variant– Extensive range of expansion I/O options– Extensive range of motor feedback devices– Extensive range of fieldbus options– Built-in safety option module, TÜV approved– UK gland box to accommodate SWA cable – Different levels of EMC compliance – Extended warranty
All ABB industrial drives use the same common options and user interfaces. These are detailed on page 53.
– The IP55 variant has been designed to occupy the same physical space as the IP21 unit, thus minimising wall space required to support this module.
– The drive has three slots for I/O and fieldbus expansion and one drive-to-drive serial communication link.
– I/O modules can be chosen from analogue expansion,
Next generation of ABB industrial drive
ABB next generation industrial drive l ABB drives and motors catalogue 2014 47
ACS880-01 – Dimensions and options
H2H1
Drive dimensions and weights wall mounted drives
H1 - Height with cable entry boxH2 - Height without cable entry boxWidth and depth with cable entry box
Frame Height 1 Height 2 Width Depth Weight
size IP21 IP21
(mm) (mm) (mm) (mm) (kg)
R1 405 370 155 226 6
R2 405 370 155 249 8
R3 471 420 172 261 10
R4 573 490 203 274 18.5
R5 730 596 203 274 23
R6 726 569 251 357 45
R7 880 600 284 365 55
R8 963 681 300 386 70
R9 955 680 380 413 98
Frame Height 1 Width Depth Weight
size IP55 IP55 IP55 IP55
(mm) (mm) (mm) (kg)
R1 450 162 295 6
R2 450 162 315 8
R3 525 180 327 10
R4 576 203 344 18.5
R5 730 203 344 23
R6 726 251 421 45
R7 880 284 423 55
R8 963 300 452 72
R9 955 380 477 100
digital expansion, encoder and resolver feedback options – Fieldbus modules can be connected to any slot and all of
the major industrial fieldbus modules are available. The drive also support two fieldbus modules at a time, so can control via a traditional industrial fieldbus, but data gather via an Ethernet based protocol
– Remote monitoring modules can be employed to monitor the drive over the web
– The safety module occupies a separate dedicated connection point ensuring safety integrity
– The drive is operated and commissioned either from a keypad or from a PC tool. The PC tool used with ACS880 is Drive Composer
– 32 drives can be connected onto a panelbus. The panelbus can be used to communicate to many drives, either using the keypad or the composer pro tool
User interfaces for ACS880-01Please refer to page 53 for details of the ACS880 common user interfaces.
IP21
IP55Highly compact same physical size as IP21 variant
WD
H
W
D
48 ABB next generation industrial drive l ABB drives and motors catalogue 2014
Next generation of ABB industrial drive
Single drive modulesSeries ACS880-04– 0.55 to 1400 kW, (380 - 690 V)– Highest power density from a module on the market,
extremely compact power module– Wheeled module supplied with extendable ramp– Coated boards as standard– Speed controlled redundant fan cooling arrangement– TÜV approved safe torque-off (STO) to SIL 3 PL e standard– Plastic IP20 shrouds supplied which can be substituted for
a pair of IP20 cabling panels which allow the module to be removed from the cabinet without disturbing customer wiring
– Brake chopper optional– Wide range of cabinet installation options, including
instructions for Rittal cabinet installation– EMC filter for C3 category according to EN 61800-3 (2004)– Optional Common mode filter– Optional fieldbus modules, safety module, I/D expansion
The ACS880-04 can be supplied in two major variant styles. The standard variant comes complete with IP20 shrouds (plastic) a telescopic ramp, separate control unit and keypad. The customer cabling is taken directly to the module and would need to be disconnected to allow module removal.
The second variant comes complete with cable panels which fit inside the cabinet. The customer cabling is attached to these panels, which allows the module to be removed without disconnecting the customer cabling, In both cases the module is withdrawn down the ramp which is provided.
There is a wide range of other control card and keypad mounting options to allow the unit to integrate into a cabinet. The manual gives extensive instructions for Rittal cabinet installation, including a list of Rittal parts required.
The following table details the R10 and R11 frames (pictured above). If you require information on the higher power modules (D8T and R8i), please contact ABB.
ACS880 – Variants, ratings, types, voltages and prices
† For fuse selection refer to the hardware manual, weak networks may require a different ratingPrice shown is complete with Keypad door mounting kit, cabling panels, EMC filter, CMF filter and manualsNote: Currents match IE3 motor ratings
380 to 415 V, 3-phase supply voltage. The power ratings are valid at nominal voltage (400 V)
No-overload Light-duty Heavy-duty Max Frame Fuse Heat Cooling Type Price
(nominal) use use use output A dissipation requirements
PN IN PLd ILd Phd Ihd A † Type aR W m3/h
kW A kW A kW A
250 505 250 485 200 361 560 R10 800 5602 1200 ACS880-04-505A-3 £14,293
315 585 315 575 250 429 680 R10 1000 6409 1200 ACS880-04-585A-3 £17,041
355 650 355 634 250 477 730 R10 1000 8122 1200 ACS880-04-650A-3 £19,154
400 725 400 715 315 566 850 R11 1250 8764 1200 ACS880-04-725A-3 £21,122
450 820 450 810 355 625 1020 R11 1600 9862 1200 ACS880-04-820A-3 £22,688
500 880 500 865 400 725 1100 R11 1600 10578 1420 ACS880-04-880A-3 £24,253
For more information – see Technical catalogue 3AUA0000115038
(+H381 +J410 +E210+E208 +R700 for cable
panels, keypad kit, EMC, CMF filter and manuals)
ABB next generation industrial drive l ABB drives and motors catalogue 2014 49
Next generation of ABB industrial drive
ACS880-04 – Dimensions and options
Drive dimensions and weights drives modules
Basic Module DImensions (no shrouds or panels)
Frame Height Height no Width Depth Weight
size (H1) pedestal (W1)
(mm) (H2) (mm) (mm) (mm) (kg)
R10 1462 1337 305 505 161
R11 1662 1537 305 505 199
Module dimensions including the Cable Panels +H381
Frame Height Height no Width Depth Weight
size (H3) pedestal (W2)
(mm) (H4) (mm) (mm) (mm) (kg)
R10 1590 1465 329 505 161
R11 1741 1616 329 505 199
Options for ACS880-04ACS880-04 is a cabinet mounted drive, so the options are designed to complement cabinet installation:– Cabling is arranged to come in at the top and motor out
at the bottom– Standard offering comes with plastic IP20 shrouds for
input and output, and motor terminals are supplied with “full sized” terminals allowing for parallel motor cables. The standard configuration is also supplied with a separate control unit and keypad
– Option +H370 requests “full sized” terminals on the input power connections allowing for parallel mains cables
– Option +H381 request full cable panels, which bolt onto the side of the module and onto the side of the cabinet wall (Replaces the standard IP20 shrouds and fixed full size cable terminals)
– Option +H356 request DC terminals– Option +P905 request the control unit to be fitted to the
power module– Option +J414 integrates the control panel onto the front of
the power module– Option +J410 includes a keypad door mounting kit with
the module– EMC filters and common mode filters can be included– Shrouds, keypads and wheeled pedestal can be removed
if required
All next generation ABB industrial drives use the same common options and user interfaces. These are detailed on page 53.
– The drive has three slots for I/O and fieldbus expansion and one drive-to-drive serial communication link
– I/O modules can be chosen from analogue expansion, digital expansion, encoder and resolver feedback options
– Fieldbus modules can be connected to any slot and all of the major industrial fieldbus modules are available. The drive also support two fieldbus modules at a time, so can control via a traditional industrial fieldbus, but data gather via an ethernet based protocol
– Remote monitoring modules can also be employed to monitor the drive over the internet
– The safety module occupies a separate dedicated connection point ensuring safety integrity
– The drive is operated and commissioned either from a keypad or from a PC tool. The PC tool used with ACS880 is Drive Composer
– 32 drives can be connected onto a panelbus. The panelbus can be used to communicate to many drives using the keypad or the Composer Pro PC tool
User interfaces for ACS880-04The ACS880-04 can be supplied with a keypad door mounting arrangement, which requires a single rectangular hole for the cabinet door.
Please refer to page 53 for details of the other ACS880 common user interfaces
H1 H2 H3 H4
W1W2
DD
Next generation of ABB industrial drive
Cabinet-built single driveSeries ACS880-07– 45 kW - 2,800 kW, (380 - 690 V)– IP21 as standard, IP42 and IP54 as options– 250 kW based on a single module including rectifier
and inverter– Coated boards as standard– TÜV approved safe torque-off (STO) to SIL 3 PL e standard– TÜV approved emergency stopping options– Extremely compact, internal swinging gate for control options
minimises cabinet size, but ensures easy access– Internal customer wiring is redesigned to give easier access,
with pluggable connectors included– Drive module can be extracted using a set of
maintenance rails– Factory-built cabinet with EMC and thermally type-tested for
trouble-free operation– Extensive range of standard options, that are increased to
incorporate the most popular engineered options ordered with the ACS800 range
– Optional UK cable option for SWA cables– Optional motor thermistor and PTC connections– Internal fieldbus options– Optional safety module– Optional I/O modules– ACS880 user interfaces described later
ACS880 – Variants, ratings, types, voltages and prices
50 ABB next generation industrial drive l ABB drives and motors catalogue 2014
For further information, see Technical Catalogue 3AUA0000098111
*130% overload, **125% overload† For fuse selection, refer to the hardware manualABB recommends the use of aR fuses for their cabinet drives, other fuses could be used if their melting curve matches ABB’s recommendations
380 to 415 V, 3-phase supply voltage. The power ratings are valid at nominal voltage (400 V)
No-overload Light-duty Heavy-duty Max Frame Fuse Heat Cooling Type Price
(nominal) use use use output A dissipation requirements
PN IN PLd ILd Phd Ihd A † Type aR W m3/h
kW A kW A kW A
55 105 55 100 45 87 148 R6 160 1795 435 ACS880-07-0105A-3
75 145 75 138 55 105 178 R6 250 1940 435 ACS880-07-0145A-3
90 169 90 161 75 145 247 R7 250 2440 450 ACS880-07-0169A-3
110 206 110 196 90 169 287 R7 315 2810 450 ACS880-07-0206A-3
132 246 132 234 110 206 350 R8 400 3800 550 ACS880-07-0246A-3
160 293 160 278 132 246* 418 R8 500 4400 550 ACS880-07-0293A-3
200 363 200 345 160 293 498 R9 630 5300 1150 ACS880-07-0363A-3
250 430 250 428 200 363** 545 R9 700 6500 1150 ACS880-07-0430A-3
AB
B p
anels can be o
rdered
with a w
ide rang
e of
standard
op
tions.
Price o
n app
lication o
nce the A
CS
880 is launched
Next generation of ABB industrial drive
ABB next generation industrial drive l ABB drives and motors catalogue 2014 51
ACS880-07 – Dimensions and options
H1 H2
Dimensions and weights, cabinet-built drives
Note: these are the dimensions of the basic cabinet, dimensions will change with the addition of some options
,
Frame Height 1 Height 2 Width Depth Weight
size IP22/42 IP54
(mm) (mm) (mm) (mm) (kg)
R6 2145 2315 430 673 240
R7 2145 2315 430 673 250
R8 2145 2315 430 673 265
R9 2145 2315 830 698 375
Options for ACS880-07ACS880-07 is a cabinet built drive, so its options fit inside the cabinet. The cabinet drive can be fitted with: – IP21, IP42, IP54, variants (no IP55) – Emergency stop variants, TÜV approved – Motor thermistor relays – Marine construction – UL approved components – Various types of cable markings, cabinet heaters, door
furniture and lighting etc. – Top or bottom cable entry for either motor or power cables – UK gland plates for SWA cables – 24 V control inside the cabinet – Different levels of EMC compliance – Extended warranty – Additionally, ABB can accommodate any specialised option
or feature by using its in-house application design team
ACS880-07 comes with options that are fitted to the drive module which is inside the cabinet: – The drive module has three slots for I/O and fieldbus
expansion and one drive-to-drive serial communication link.– I/O modules can be chosen from analogue expansion,
digital expansion, encoder and resolver feedback options – Fieldbus modules can be connected to any slot and all of
the major industrial fieldbus modules are available. The drive also supports two fieldbus modules at a time, so can control, via a traditional industrial fieldbus, but data gathers via an Ethernet-based protocol
– Remote monitoring modules can be employed to monitor the drive over the internet
– The safety module occupies a separate dedicated connection point ensuring safety integrity
– The drive is operated and commissioned either from a keypad or from a PC tool. The PC tool used with ACS880 is Drive Composer
– 32 drives can be connected onto a panelbus. The panelbus can be used to communicate to many drives, either using the keypad or the composer pro tool
User interfaces for ACS880-07Please refer to page 53 for details of the ACS880 common user interfaces
IP21 IP54
WD
WD
Next generation of ABB industrial drive
ABB multidriveA multidrive is a custom-made system to suit a larger application or a process line. The system contains multiple inverter stages of differing size, supplied from a common DC bus.
ABB can provide a ready-made cabinet, or it can provide system integrators with a comprehensive range of power modules and mechanical kits to build bespoke cabinets for end clients.
Series ACS880 multidrive cabinets– 1.5 kW - 5600 kW– IP21 as standard IP42 as option– High packing density with 16 inverter units (up to frame size
R2i) can be installed into one 1000 mm cabinet– Diode bridge that is highly reliable with high power density– Fast connectors for motor cables in the bottom part of the
cabinet making installation easy– Integrated safety including safe torque-off (STO) as standard
with several safety functions as options– Coated boards as standard– Braking options– DC fuse disconnectors, DC fuses or DC fuse switch including
charging circuit for inverters– Cabinet light and heater options– Highly efficient thermal handling as heat loss of each inverter
unit is guided to the back of the cabinet. All cabinets are their own separate compartment
– Long lifetime capacitors and high efficiency cooling fan with speed or on-off control
– TÜV approved emergency stops– ACS880 user interfaces described later
Series ACS880 multidrive modules– 1.5 kW - 2200 kW– A range of IP20 modules and IP00 kits to generate bespoke
multidrive systems built into system integrators own panels– Modules have no rectifiers, they are inverters only and range in
frames from R2i to R8i (i=inverter only)– Inverter modules contain internal pre-charge circuits making
them easier to integrate– Inverter modules are extremely compact, making cabinet line-
ups extremely compact and competitive– Selection of rectifiers available to generate DC link for the
system. Active IGBT rectifiers and diode modules are available– New style diode module (DxD) only contains diodes, making it
more competitively priced and more reliable– Cabinet kits ensure easy integration– Integrated safety including safe torque-off (STO) as standard
with several safety functions as options using the new safety module
– Coated boards as standard- ACS880 user interfaces described later
52 Next generation ABB industrial drives l ABB drives and motors catalogue 2014
For further information, see Technical Catalogue 3AUA0000115037
For further information, see Technical Catalogue 3AUA0000115038
RectifierInverter
Inverter
Inverter
New control panelState-of-the-art high resolution keypad brings a new level of usability to the drives marketplace. The keypad is designed by industrial designers to ensure maximum usability and intuitive use. The keypad display is extremely high definition and is visible in any control room. Innovative views, transitions and screen will be very familiar to users of smartphone technology. The display supports graphics and icons to help the user navigate. The keypad also supports text editing to allow users to re-name fault messages to match plant specific actions. Customer specific start-up images and parameter favourite make the keypad easily tailorable to customers and OEMs alike.
Removable memory unitThe memory unit stores the complete parameter and firmware set for the drive. Should a drive need to be replaced, swapping the memory unit to the new drive will transfer a complete drive set-up – absolutely no recommissioning is required. This reduces down time in the event of a problem.
FieldbusThe ACS880 supports an extensive list of fieldbus modules for connectivity to industrial networks. These modules are common with other drives within the ABB drives range.
Expansion for analogue and digital I/OAdditional I/O can be added to the ACS880. This I/O can be addressed by the fieldbus so that the ACS880 can be used as an I/O “nest”, or the I/O can be used to simply allow more connectability from the process to the drive, for example, flow or level transducers.
High resolution, high contrast display
Multiple display screens supporting graphs, bar graphs and graphical meters
Icon driven menu selections and displays
Real-time clock
USB connection – no special leads required
Next generation of ABB industrial drive
Next generation ABB industrial drives l ABB drives and motors catalogue 2014 53
ACS880 – Common user interfaces
Safety module, FSO-11SIL3 rated TÜV approved safety module fits within the drive, to offer drive specific safety functions. Safely Limited Speed (SLS), Safe Maximum Speed (SMS), Safe Stop Emergency (SSE), Safe Stop 1 (SS1) / stop category 1 and Safe Brake Control (SBC) can be realised with no encoder feedback required (patent pending).
Drive Composer PC toolDrive Composer is the new PC tool for the ACS880 family. The PC tools come in two variants – the “entry” level is a free of charge point-to-point tool and allows simple parameter editing and storage, as well as monitoring and commissioning support, while the “Pro” level has all of this as well as animated control diagrams and extended commissioning, monitoring and diagnostic support, as well as the ability to program the safety functions. The Pro tool also allows the user to connect to multiple drives either over “panelbus” where the keypad port is used, or over Ethernet.
Fault
XPOW External power input
1 +24VI24 V DC, 2 A
2 GND
XAI Reference voltage and analogue inputs
1 +VREF 10 V DC, RL 1 to 10 kohm
2 -VREF -10 V DC, RL 1 to 10 kohm
3 AGND Ground
4 AI1+ Speed reference 0(2) to 10 V, Rin > 200 kohm5 AI1-
6 AI2+ By default not in use. 0(4) to 20 mA, Rin > 100 ohm 7 AI2-
J1 J1 AI1 current/voltage selection jumper
J2 J2 AI2 current/voltage selection jumper
XAO Analogue outputs
1 AO1Motor speed rpm 0 to 20 mA, RL < 500 ohm
2 AGND
3 AO2Motor current 0 to 20 mA, RL < 500 ohm
4 AGND
XD2D Drive-to-drive link
1 B
Drive-to-drive link or built-in Modbus2 A
3 BGND
J3 J3 Drive-to-drive link termination switch
XRO1, XRO2, XRO3 Relay outputs
1 NC Ready 250 V AC/30 V DC 2 A
2 COM
3 NO
1 NC Running 250 V AC/30 V DC 2 A
2 COM
3 NO
1 NC Faulted (-1) 250 V AC/30 V DC 2 A
2 COM
3 NO
XD24 Digital interlock
1 DIIL By default not in use
2 +24VD +24 V DC 200 mA
3 DICOM Digital input ground
4 +24VD +24 V DC 200 mA
5 DIOGND Digital input/output ground
J6 Ground selection switch
XDIO Digital input/outputs
1 DIO1 Output: Ready
2 DIO2 Output: Running
XDI Digital inputs
1 DI1 Stop (0)/Start (1)
2 DI2 Forward (0)/Reverse (1)
3 DI3 Reset
4 DI4 Acceleration and deceleration select
5 DI5 Constant speed 1 (1=On)
6 DI6 By default not in use
XSTO Safe torque-off
1 OUT1
Safe torque-off. Both circuits must be closed for the drive to start.
2 SGND
3 IN1
4 IN2
X12 Safety functions module connection
X13 Control panel connection
X205 Memory unit connection
Typical I/O and control connectionsThe ABB industrial drive family uses the same control card, keypad and software structure throughout its entire range. All I/Os are fully configurable to be whatever function is required. The diagram shows a typical I/O connection.
The ACS880 uses macros to configure its I/O. The macros pre-define the I/O functionality to comply with popular industrial configurations. It is also possible to configure the I/O manually to any function required.
The ACS880 control card showing the colour coded terminal strips
Next generation of ABB industrial drive
54 Next generation industrial drives from ABB l ABB drives and motors catalogue 2014
ACS880 – Common user interfaces
ABB motion control drive Series ACSM1– For demanding machinery applications – One drive for all motor types– For synchronous and induction motors – Adaptable design with modular, compact hardware – Memory unit for easy drive management and re-commissioning – Wide range of feedback interfaces– Solution programming to extend drive functions, DriveStudio
(IEC 61131 compatible)– Modular and compact design, includes the functionality needed
for the application– Safe torque-off (SIL3 rated), TÜV approved
ABB machinery drive modulesSeries ACS850-04– New higher powered module. Integral wheels and shrouding– Optimal power frame sizes and side-by-side mounting– Power in at top, motor out at bottom for logical cable
management within the cabinet– DC bus connection - common DC link schemes are possible– Integrated brake chopper - choppers in each module can be
used when on a DC link, to distribute braking– DTC motor control platform– DriveStudio and DriveSPC PC tools for customising the
parameter driven drive with IEC61131 application coding and software application blocks
– Memory module contains the complete firmware, parameter and programme set-up – no re-commissioning
– STO, safe torque-off to SIL3/PL e as standard– Modules which compliment the full range of multidrive modules
For further information see Technical Catalogue 3AUA0000041481
For technical information see Technical Catalogue 3AKA0000068580
ABB motion control solutionsABB offers an extensive range of machine controlsolutions for diverse industrial applications such aslabelling, packaging, bottling, pick and place, lasercutting/trimming, stacking, cut-to-length, flying shear,web feeders and high speed rotary wrappers.
ABB’s motion control solutions include human-machine interfaces (HMIs), programmable logic controllers (PLCs) and safety technology. Solutions extend to multi-axis motion controllers, high performance servo drives, rotary servo motors and linear motors. All of which seamlessly interface to provide a complete machine control solution.
To compliment the motion and machinery products, ABB offers an extensive range of industrial servo motors and cables. Motors are stocked or can be ordered with a wide range of options to suite application needs or DC retrofitting.
ABB motion control drive and ABB machinery drive module
For more details, please refer to Technical Catalogue 3AFE68675073
ABB machinery drives and ABB motion control drives l ABB drives and motors catalogue 2014 55
Medium voltage AC drives
What is a medium voltage AC drive?ABB offers a complete range of medium voltage AC drives for speed and torque control and for the starting of large AC motors. The drives, which are built with reliable IGCT power semiconductor technology, are available as complete package solutions including transformers and motors.
Series ACS1000i – Single drives 315 kW to 2,000 kW – Air-cooled, 24-pulse drive with integrated input transformer– Retrofit-ready for existing motors, suitable for most
MV applications– Integrated output sine filter for pure sinusoidal voltage
and current output– Offshore cabinet versions available
Series ACS1000– Single drives from 315 kW to 5 MW– Air-cooled (315 kW to 2 MW) and water-cooled
(2 kW to 5 MW) versions– Retrofit-ready for existing motors, suitable for
most MV applications– Integrated output sine filter for pure sinusoidal
voltage and current output– Offshore cabinet versions available
Series ACS2000– Single drives from 250 kW to 2.6 MW – Active rectifier unit or 24-pulse diode front end for minimal
line side harmonics– Regeneration and power factor correction with active
rectifier– Direct-to-line versions for operation without an input
transformer – Multilevel topology allows the use of standard motors – Simple drive system integration – Modular power modules for reduced MTTR– Sine filter output optional, for retrofit and long cable run
applications
Series ACS5000– Single drives from 1.5 MW to 35 MW – Air-cooled (1.5 MW to 6 MW) and water-cooled
(4.5 MW to 35 MW) versions – Air-cooled version with integrated input transformer
(1.5 MW to 4.1 MW)– Multilevel topology allows the use of standard motors – Multilevel fuseless topology results in a drive with
unbeatable efficiency, reliability and footprint – Optimal network friendliness due to 36-pulse configuration
56 Medium voltage AC drives l ABB drives and motors catalogue 2014
Medium voltage AC drives and low voltage DC drives
Medium voltage drives cont...Series ACS6000– Single or multidrives 3 MW to 27 MW– Active rectifier unit available for 4-quadrant operation,
reduced harmonics and adjustable power factor– Line supply unit available for 2-quadrant operation
and a constant power factor of 0.96 across entire speed range
– Modular design for optimum configurations, including multidrive configurations
– Offshore cabinet versions available
Series MEGADRIVE LCI– 2 MW to 72 MW (higher power on request)– High power with series connection of thyristors– N+1 thyristor redundancy possible– Fuseless design– Water- and air-cooled converters available– Line side harmonics: 6-pulse, 12-pulse or 24-pulse– Motor side harmonics: 6-pulse or 12-pulse– High converter efficiency– Proven technology and design– Complete package solutions including transformers,
drives and motors
ABB general purpose DC drivesSeries DCS550– Range from 20 to 1000 A DC– 230 V AC to 525 V AC– DCS550 is a digital DC drive targeted at OEMs,
such as machine builders– Start-up assistants and commissioning wizards– Same state of the art keypad as ACS550– Extensive range of fieldbus interfaces– Adaptive program for additional flexibility– Onboard field controller
ABB industrial DC drivesSeries DCS800– From 25 to 5200 A– Commissioning wizard gives easy start-up– Easy to use - standard macros or user programmability– Intuitive control panel with ‘Help’ key, consistent with
many of the AC drives– Adaptive programming for additional flexibility– Modules can be connected in parallel up to 20,000 A– Uses ACS800 I/O option modules and fieldbus modules– I/O is backward compatible with DCS500 and DCS600– Field converters built-in (up to 25 A)
Medium voltage AC drives and low voltage DC drives l ABB drives and motors catalogue 2014 57
Overview– Actively eliminates harmonics in a controlled way– Filters up to 50th harmonic in accordance with
G5/4 requirements. Each harmonic individually programmable
– Redundancy feature allows units to continue when others have shut down
– Active filters - only work when harmonics are present thereby reducing unwanted losses, resulting in greater overall efficiency
– Close loop for better measurement of harmonics - thereby more accurately eliminating the potentially damaging harmonic
– Auto-detection of CT polarity - ensures accurate current distortion readings on network, resulting in easy commissioning
– Stores record trail. Fault and event log - any trip will have a record trail
Series PQFM, PQFI – Available in IP00 back plane or IP21, IP42 cabinets– New intuitive user interface– Current ratings, 70 A, 100 A, 130 A, 150 A, 250 A, 450 A,
per module. The modules can be connected in parallel to a maximum of eight modules of equal rating
Series PQFs– Small compact unit suitable for wall mounting– Low ratings available from 30 A, 45 A, 60 A, 70 A, 80 A,
90 A, 100 A. The modules can be connected in parallel to a maximum of four modules of equal rating
– Same user interface as the larger units– Available in IP30
Power quality filters (PQF)
58 Power quality filters l ABB drives and motors catalogue 2014
Remote monitoring options
Remote monitoring overview Remote monitoring is the reporting of information back to the user, from a remote station or location. Typical remote monitoring information can include: - Energy consumption and savings - Motor condition - Warnings (predictive maintenance),
faults and alarms - Diagnostics - Monitoring actual values and
parameters– Parameter access is possible, but is
not the primary function of remote monitoring
Ethernet adapter – for ABB machinery drives and ABB standard drivesSeries - SREA-01 Ethernet adapter provides remote monitoring access for up to 10 drives. It connects to the drive(s) via an RS485 modbus interface. It can send process data, data logs and event messages independently, without a PLC or a dedicated on-site computer. The module can send either e-mails or SMS text messages to inform the user of the status of the drive(s) connected to it. It has an internal web server for easy configuration and drive access. Web pages can be configured with site photos and site naming.
Ethernet adapater for ABB industrial drivesSeries - NETA-01, NETA-21NETA-01 module provides remote access to nine ABB industrial drives. The module connects to the drive via a high speed optical connection that can be configured in a ring or star configuration. It can send process data, data logs and event messages independently, without a PLC or a dedicated on-site computer. The module can send either e-mails or SMS text messages to inform the user of the status of the drive(s) connected to it. It has an internal web server for easy configuration and drive access. Web pages can be configured with site naming. Full parameter access is possible.
Ethernet adapater for local communiationSeries - MOXAMOXA module provides remote access to a single individual drive. The module connects to the drive via an RS232 connection to the keypad/panel port of the drive. It is a low cost point-to-point remote monitoring device. MOXA is ideal as a point-to-point device over which commissioning tools can be connected to the drive from a remote location, so diagnosis of faults and problems are possible.
High speed drive monitoring – remote diagnoticsSeries – DriveMonitorDriveMonitor is a service tool which can be fitted to any ABB industrial drive in case of site problems and issues. It uses high speed optical connections to the drives power stages and monitors all of the switching signals sent. In this way complicated system problems can be diagnosed. DriveMonitor can also be used as a system optimisation and recording tool, as its memory buffers can save up to one years worth of performance data.
Monitor drives on existing networksSeries – DriveBrowser PC toolDriveBrowser allows a user to monitor any ABB drive connected to an existing Ethernet network, without having to connect another “tools” chain network on the site. Connect DriveBrowser to a suitable “hub” location and view, edit and tune all of the ABB drives on the Ethernet ring.
Remote monitoring options l ABB drives and motors catalogue 2014 59
Software tools
ABB offers several software tools to facilitate and enhance the use of ABB drives. These tools provide a user-friendly and easy-to-use approach for the selection, commissioning and use of AC drives.
Integration and programming toolsDrive Composer
The Drive Composer PC tool offers fast and harmonised set-up, commissioning and monitoring for the new ABB industrial drive portfolio. The tool has two variants, a free version called Drive Composer
Entry and a professional level tool which is licensed. The free version of the tool provides start-up and maintenance programming with monitoring and parameter editing, while the professional version provides additional features such as custom parameter windows, control diagrams for easy parameter editing of the drive’s configuration and the ability to programme the built-in safety module. Drive Composer will have add-ons for adaptive programming and CoDeSys programming for more complicated system designs.
DriveAP For adaptive programming of ABB industrial drives.
This PC tool is used to create, document, edit and download adaptive programs. Adaptive programming can be done with the standard control panel or with DriveAP.
DriveAP offers a clear and easy way to develop, test and document adaptive programmes with a PC. It modifies function blocks and their connections and requires no special programming.
DriveStudio A user-friendly PC environment for simple drive commissioning tasks as well as more demanding drive tuning and programming tasks. DriveStudio is used with the ABB machinery drive and ABB motion control drives and water and wastewater drives. Drive Studio contains:
Commissioning and tuning – Drive overview screen– Parameter setting and signal monitoring – Data logger and on-line signal monitoring for tuning
Solution programme composer – Function block programming with standard function
block library
– Professional programming environment: hierarchy levels, custom circuits, user parameters, copy protection etc.
DriveCAM toolMultiple methods for designing axis profile between reference axis and controlled drive axis
Start-up and maintenance toolsDriveWindowA Windows application used for commissioning and maintenance. Functions include local control, monitoring, parameter edits, fault logging, trending, backup and restore
– Shows actual status of the connected drive– Edit and show the drive parameters– Save and load drive parameters– Backup and restore drive parameters– Offline configuration of drive parameters– Read fault loggers and diagnostic data
Used with ABB industrial drives equipped with high-speed fibre optic communication, or remotely via the Internet.
DriveWindow Light Available for ABB general purpose drives and ABB machinery drives, has the same functions as DriveWindow but is designed for point-to-point communication, via control panel port.
DriveConfig Dedicated programming tool for the ABB micro drive. Allows access to the extended parameter set of ACS55 and allows un-powered programming.
Drive Analyser New PC tool to allow long term analysis of performance and diagnostics. Data can be collected for up to one year.
To download software tools, go to: www.abb.com > drives > drive PC tools.
60 Software tools l ABB drives and motors catalogue 2014
Software tools
Engineering toolsDriveSize For dimensioning drives and motors. This PC programme helps select an optimal motor, drive and transformer, which
is especially useful where a straightforward selection from a catalogue is not possible. DriveSize is used to compute network harmonics and to create documents about dimensioning. It contains current versions of ABB’s motor and drive catalogues.
It can also be used in conjunction with ABB machinery drives to specify the dimensions of different kinds of linear or rotary movement mechanisms such as lead screws, rack and pinion combinations, belts and pulleys, conveyors, feed rolls and rotating tables.
DriveSize software can be used in Win98, WinNT, Win2000 and WinXP and Windows 7 operating systems.
DriveChopper For dimensioning a braking chopper and resistor.
DriveChopper is a web tool for braking chopper and resistor dimensioning. The programme is created especially for system designers who need a braking unit for a particular drive application.
DriveUpgradeFor finding an adequate drive to replace an old one. This on-line tool is ideal for finding a replacement to an existing ABB drive that may be
coming to the end of its useful life. Simply input some basic information and the modern equivalent drive will be revealed.
To download, go to: www.abb.com > drives > drive PC tools.
Energy saving toolsFor comparison of energy consumption between different flow control methods in pumps and fans, ABB has developed calculation tools for estimating the energy savings that become available when applying electric speed control to certain flow machines.
PumpSaveFor comparing AC drive control against throttling, on/off and hydraulic coupling control in pumps. Calculate how much energy and money you could be saving with ABB drives while also deriving other benefits such as soft starting and stopping, an improved power factor and connection into process automation. PumpSave also carries out a simple dimensioning and recommends an appropriate ABB drive type. Medium voltage drives now included.
FanSave For comparing AC drive control against traditional flow control methods in fans. Calculate the savings you can achieve by replacing outlet damper, inlet vane or pitch control methods with electronic speed control from an ABB drive. FanSave also provides financial and environmental figures concerning the control method retrofit project and recommends a suitable ABB drive type.
The ABB Energy Calculator App The App allows users to calculate the energy savings you can achieve on a typical pump or fan load by replacing direct-on-line control with a variable-speed drive. Simply select your industry and the operating duty profile, the voltage, phase and motor power rating, running hours and electricity cost. The App then estimates how much CO2, energy and money you can save by installing an ABB drive to control the application.
To download the ABB Energy Calculator App, visit the Apple APP store.
To download a series of energy saving tools go to: www.abb.co.uk/energy
Software tools l ABB drives and motors catalogue 2014 61
Drives life cycle services
Service options for variable-speed drives A proactive drives maintenance programme keeps you competitive by minimising disruption to your production.
The many drives used in industry have a high degree of reliance placed upon them. Although drives are not normally the most expensive pieces of capital equipment, they often perform critical duties and have a high in-service value. A drive failure can result in loss of production and revenues, as well as having safety and environmental consequences. To reduce the risk and consequences of failure, the drive must be properly maintained at the right times in its lifecycle.
ABB provides customised and standard levels of service for drives support. The service levels mean your exact operational and financial needs can be met, maximising the reliability of your plant over its entire lifecycle. Service elements can be combined into a service contract, help with planning and budgeting.
Life cycle servicesThe services offered by ABB span the entire value chain, from the moment a customer makes the first enquiry to disposal and recycling of the drive. Thro ughout the value chain, ABB provides training, technical support and customised contracts. All of this is supported by one of the most extensive global drive sales and service networks.
Pre-purchaseABB provides a range of services that help guide the customers to the right products for their applications.
Order and deliveryOrders can be placed directly to ABB or through ABB’s channel partners. ABB’s sales and service network offers timely deliveries including express delivery.
Installation and commissioningWhile many customers have the resource to undertake installation and commissioning on their own, ABB and its channel partners offer professional installation and start-up services.
Operation and maintenanceThrough remote monitoring, ABB can guide the customer through a fast and efficient fault-finding procedure as well as analyse the operation of the drive and the customer’s process. From site surveys to preventive maintenance and reconditioning of drives, ABB has all the options covered to keep its customers’ processes operational.
Upgrade and retrofitAn existing ABB drive can often be upgraded to the latest software or hardware to improve the performance of the application. Existing processes can be economically modernised by retrofitting the latest drive technology to cooling fans, removing the need for mechanical control equipment, such as inlet guide vanes or dampers and improving efficiency through energy savings.
Replacement and recyclingABB can advise on the best replacement drive while ensuring that the existing drive is disposed of in a way that meets all local environmental regulations.
Entire value chain servicesThe main services available throughout the entire value chain include:− Training and learning - ABB offers product and
application training− Technical support - At each stage of the value chain,
an ABB expert is available to offer advice to keep the customer’s process or plant operational.
− Contracts - Customised contracts can be devised between the customer and ABB.
The full portfolio of life cycle services are described in a separate brochure that is available on request – please call 07002 SERVICE (07002 7378423) for a copy.
Drives AdvantageABB’s certified partners provide Drives Advantage: a series or services targeting the current range of products up to 400 kW. Services include:− installation− start-up assistance− upgrades− hire services− planned maintenance− repairs− energy surveys− training
The full portfolio of Drives Advantage services are described in a separate brochure that is available on request – please call 07000 DRIVES (07000 374837) for a copy.
ABB University - Professional drives trainingFactory certified courses delivered in a bespoke drives training facility by experienced applications and service personnel.With ABB University you can enrol onto either e-learning or classroom based courses. Please call 01785 285939 or visit www.abb.co.uk/abbuniversity
62 Drive life cycle services l ABB drives and motors catalogue 2014
ABB low voltage AC motors l ABB drives and motors catalogue 2014 63
ABB low voltage AC motors
Motors for hazardous areas - page 74 56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Flameproof motors
Increased safety motors
Dust ignition proof motors
Non-sparking motors
Sizes 56-4504504003553152802502252001801601321121009080716356
Process performance motors - page 67
Premium efficiency motors
Cast iron motors
56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
General performance motors - page 6455 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Aluminum motors
Cast iron motors
General performance motors56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Cast iron motors
Aluminum motors
Marine motors56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
General performance motors (aluminium, cast iron)
Process performance motors (cast iron)
Open drip proof motors
00 225 250 280 315 355 400 450
Open drip proof motors
Single phase motor
Servo motors
s
Smoke venting motors
Roller table motors
Water cooled motors
Permanent magnet motors
Wind turbine generators
Motors for additional applications56 63 71 80 90 100 112 132 160 180 2
Brake motors
High ambient motors
Motors for hazardous areas - page 76 56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Flameproof motors
Increased safety motors
Dust ignition proof motors
Non-sparking motors
Sizes 56-4504504003553152802502252001801601321121009080716356
Process performance motors - page 69
Cast iron motors
Premium efficiency motors
Aluminium motors
56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
General performance motors - page 6656 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Aluminum motors
Cast iron motors
General performance motors56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Cast iron motors
Aluminum motors
Marine motors56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Process performance motors (cast iron)
General performance motors (aluminium, cast iron)
Process performance motors (aluminium)
00 225 250 280 315 355 400 450
Single phase motor
Servo motors
SynRM
s
Smoke venting motors
Roller table motors
Water cooled motors
Permanent magnet motors
Wind turbine generators
Motors for additional applications56 63 71 80 90 100 112 132 160 180 2
Brake motors
High ambient motors
Motors for hazardous areas - page 76 56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Flameproof motors
Increased safety motors
Dust ignition proof motors
Non-sparking motors
Sizes 56-4504504003553152802502252001801601321121009080716356
Process performance motors - page 69
Cast iron motors
Premium efficiency motors
Aluminium motors
56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
General performance motors - page 6656 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Aluminum motors
Cast iron motors
General performance motors56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Cast iron motors
Aluminum motors
Marine motors56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Process performance motors (cast iron)
General performance motors (aluminium, cast iron)
Process performance motors (aluminium)
00 225 250 280 315 355 400 450
Single phase motor
Servo motors
SynRM
s
Smoke venting motors
Roller table motors
Water cooled motors
Permanent magnet motors
Wind turbine generators
Motors for additional applications56 63 71 80 90 100 112 132 160 180 2
Brake motors
High ambient motors
Motors for hazardous areas - page 76 56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Flameproof motors
Increased safety motors
Dust ignition proof motors
Non-sparking motors
Sizes 56-4504504003553152802502252001801601321121009080716356
Process performance motors - page 69
Cast iron motors
Premium efficiency motors
Aluminium motors
56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
General performance motors - page 6656 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Aluminum motors
Cast iron motors
General performance motors56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Cast iron motors
Aluminum motors
Marine motors56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Process performance motors (cast iron)
General performance motors (aluminium, cast iron)
Process performance motors (aluminium)
00 225 250 280 315 355 400 450
Single phase motor
Servo motors
SynRM
s
Smoke venting motors
Roller table motors
Water cooled motors
Permanent magnet motors
Wind turbine generators
Motors for additional applications56 63 71 80 90 100 112 132 160 180 2
Brake motors
High ambient motors
Motors for hazardous areas - page 76 56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Flameproof motors
Increased safety motors
Dust ignition proof motors
Non-sparking motors
Sizes 56-4504504003553152802502252001801601321121009080716356
Process performance motors - page 69
Cast iron motors
Premium efficiency motors
Aluminium motors
56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
General performance motors - page 6656 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Aluminum motors
Cast iron motors
General performance motors56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Cast iron motors
Aluminum motors
Marine motors56 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400 450
Process performance motors (cast iron)
General performance motors (aluminium, cast iron)
Process performance motors (aluminium)
00 225 250 280 315 355 400 450
Single phase motor
Servo motors
SynRM
s
Smoke venting motors
Roller table motors
Water cooled motors
Permanent magnet motors
Wind turbine generators
Motors for additional applications56 63 71 80 90 100 112 132 160 180 2
Brake motors
High ambient motors
For more information call 07000 MOTORS (07000 668677)
64 European MEPS for low voltage motors l ABB drives and motors catalogue 2014
European MEPS for low voltage motors
Super premium efficiency IE4 Not yet defined
Premium efficiency IE3 Premium
High efficiency IE2 Comparable to Eff1
Standard efficiency IE1 Comparable to Eff2
2014RegulationEU 4/2014introduced
2009EuP Directive2005/32/ECEco-designformallyadoptedEC 640/2009
Mandatory EuP DirectiveApplies to motors:– rated voltage up to 1000 V– single-speed, three-phase, 50 Hz– 2, 4 and 6-pole– rated output from 0.75 kW to 375 kW– S1 Duty
Does not apply to motors designed to operate exclusively:– in potentially explosive atmospheres as defined
in ATEX directive 94/9/EC– brake motors– ambient air temperature outside the range
-30°C to +60°C– altitudes exceeding 4000m asl– maximum operating air temperature above 400˚C
Phase 1 Motors must meet the IE2 efficiency level From 16 June, 2012
Phase 2 Motors with a rated output of 7.5 kW - 375 kW must meet From 1 January, 2015 EITHER the IE3 efficiency level OR the IE2 level if fitted with variable-speed drive
Phase 3 Motors with a rated output of 0.75 kW - 375 kW must meet From 1 January, 2017 EITHER the IE3 efficiency level OR the IE2 level if fitted with variable-speed drive
Implementation timetable
Standard for LV motor efficiency classesMotors covered by standard include:− Single-speed, three-phase, 50 and 60 Hz− 2, 4 or 6-pole
− Rated output from 0.75 kW to 375 kW− Rated voltage UN up to 1000 V
− Duty type S1 (continuous duty) or S3 (intermittent periodic duty) with a rated cyclic duration factor of 80 percent or higher− Capable of operating direct online
50 and 60 Hz
2008IEC 60034-30
2007IEC 60034-2-1
Standard on efficiency measurement methods
Introduces new rules concerning the testing methods to be used for determining losses and efficiency.
The resulting efficiency values differ from those obtained under the previous IEC testing standard IEC 60034-2: 1996
ABB calculates efficiency values according to the indirect method, with additional losses determined from measurement. This is the preferred low uncertainty method outlined in the standard.
For more information call 07000 MOTORS (07000 668677)
Urgent action needed before 1st January 2015 - see Phase 2 below
MotorAdvantage l ABB drives and motors catalogue 2014 65
MotorAdvantageA scheme to determine how best to save money, reduce energy use and lower maintenance costs from a plant’s installed electric motor base.
MotorAdvantage aims to encourage industry to uncover the true cost of running electric motors. Research by ABB reveals that UK industry is failing to efficiently manage its motor inventory, thereby incurring millions of pounds of unnecessary downtime, repair and energy costs.
MotorAdvantage is aimed at companies operating a continuous process such as those found in food & beverage, chemical, oil & gas and pharmaceuticals. Such processes tend to have critical applications, whereby if a motor fails the cost to a company can be hundreds of pounds per hour in lost revenue. It is not just the loss of production but the potential loss of the company’s customer.
How it worksThere are three stages to MotorAdvantage:
1. ConsultationDuring the consultation process ABB examines the installed motor asset register for the plant and, working with the local engineers, identifies up to five critical applications that are running either continuously or for more than 4,000 hours per annum. They then determine some basic information about these motors such as:– How old are the installed motors? – How efficient are the installed motors?– How many hours do they run per annum?– Have they been rewound before?– What spares holding do you have for critical plant? – What is your repair/rewind policy for ‘failed’ motors?
ABB also engages with the plant’s process engineers to determine the exact design criteria for the various processes. This gives ABB a clearer understanding of how the process is meant to operate and its critical design operating points, thereby ensuring that a properly dimensioned motor is selected should a replacement be deemed necessary.
2. The AppraisalAn ABB engineer, or one of ABB’s authorised channel partners, visits the end-user to inspect the selected motors, get an understanding of the plant, the inventory of spare motors, energy and maintenance plans. It is not unusual to find that an old motor can be 1-5 percent lower in efficiency compared to a new premium efficiency variant. If that motor is running continuously then you can achieve a typical payback of between two to three years should you wish to take the decision to scrap the motor prior to failure.
If the motor is replaced at the point of failure then taking the rewind cost into the payback calculation, the new motor cost can be recovered in less than 12 months. Bear in mind that
many rewound motors will only have a six month warranty of the repaired components whilst a new premium efficiency motor from ABB will come with a full three year warranty.
3. Proving the savings – report and recommendationsFollowing the collection of the data, the findings are analysed and potential savings identified using dedicated software. The findings are methodically presented, with tables being created to help identify where savings are likely to arise. Among the data available includes an estimation of present energy usage; whether the application would benefit from variable-speed control; payback time if an investment is made in new motors; carbon dioxide emission reductions; along with many other key facts and analysis.
An action plan is prepared, usually comprising an Executive Summary and a detailed Engineer’s Report, highlighting applications that can save the most. The figures will normally be translated into monthly savings, and there will be detailed recommendations for implementation.
Benefits– In just half-a-day, an ABB engineer can quickly assess up
to five installed motors that could benefit from a motor management plan
– Assesses the end-users current policy in the event of a motor failure and the financial impact on the company
– Identifies improvements to be made with regards to maintenance and stockholding
– Determines the energy use of the current installation– Avoids damage to a customers brand or image caused
through loss of production – Avoids overly ambitious motor management plans that try
to assess every single motor on a plant
66 Low voltage AC motors l ABB drives and motors catalogue 2014
General performance motors
What is a general performance motor? General performance motors combine convenience and easy handling seamlessly with ABB’s engineering expertise, while at the same time providing standard variants and modifications. The motors can be tailored according to the specific needs of OEMs. The high modularity enables adding a wide variety of elements to the robust frame, thus making the overall solution to fit the specific situation and customer need perfectly. As the user only pays for the enhancements needed and used, the motors are free from all unnecessary elements.
Where can it be used?– End-users in industry– Tailored serial project OEM’s– Pumps– Fans– Compressors
Highlights– Variant codes from production which OEM
customers need– One year warranty– IE2 efficiency– 2, 4 & 6 pole designs
General performance cast iron motors l ABB drives and motors catalogue 2014 67
General performance cast iron motors, 71-355, 2, 4 & 6 poles
TEFC low voltage motors, cast iron, IP 55, IC 411, single-speed. 400 V 3-phase 50 Hz See product catalogues or www.abb.com/motors&generators for more information on products.
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
3000 r/min = 2 poles
0.37 M2BA 71 MA 1.32 0.96 69.2 £150 £164
0.55 M2BA 71 MB 1.95 1.27 73.2 £154 £173
0.75 M2BA 80 MB 2.4 1.81 80.6 £204 £222
1.1 M2BA 80 MC 3.6 2.4 81.8 £258 £296
1.5 M2BA 90 SLB 4.9 3 82.2 £306 £346
2.2 M2BA 90 SLC 7.2 4.3 84.7 £379 £418
3 M2BA 100 LB 9.7 5.9 85.2 £461 £512
4 M2BA 112 MB 13.1 7.7 86.1 £545 £598
5.5 M2BA 132 SMB 18.3 10.4 88.0 £714 £782
7.5 M2BA 132 SMC 24.7 14.5 88.6 £906 £977
11 M2BA 160 MLA 35.9 19.8 89.8 £962 £1,053
15 M2BA 160 MLB 48.8 26.4 91.1 £1,225 £1,313
18.5 M2BA 160 MLC 60.2 32.9 91.0 £1,456 £1,544
22 M2BA 180 MLA 71.6 38.1 91.5 £1,732 £1,868
30 M2BA 200 MLA 97.1 52.7 92.2 £2,361 £2,544
37 M2BA 200 MLB 119 63.4 92.5 £2,911 £3,094
45 M2BA 225 SMA 145 77.6 93.0 £3,410 £3,622
55 M2BA 250 SM 177 93.9 93.9 £4,167 £4,410
75 M2BA 280 SMA 240 130 94.0 £6,608 £6,965
90 M2BA 280 SMB 288 153 94.3 £7,947 £8,304
110 M2BA 315 SMA 352 195 94.6 £9,679 £10,286
132 M2BA 315 SMB 422 228 94.9 £11,697 £12,304
160 M2BA 315 SMC 512 272 95.2 £14,518 £15,125
200 M2BA 315 MLA 640 336 95.3 £18,215 £18,822
250 M2BA 355 SMA 800 424 95.4 £23,072 £24,143
315 M2BA 355SMB 1009 535 95.4 £28,929 £30,000
355 M2BA 355SMC 1136 609 95.5 £32,679 £33,750
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1000 r/min = 6 poles
0.18 M2BA 71 MA 1.9 0.57 63.7 £160 £181
0.25 M2BA 71 MB 2.6 0.77 67.2 £183 £206
0.37 M2BA 80 MA 3.8 1.09 71.0 £201 £227
0.55 M2BA 80 MB 5.7 1.51 73.9 £225 £255
0.75 M2BA 90 SLC 7.4 2.3 78.7 £236 £266
1.1 M2BA 90 SLE 11.2 3 78.2 £278 £312
1.5 M2BA 100 L 15 3.8 82.2 £348 £387
2.2 M2BA 112 MB 22.1 5.5 82.5 £469 £512
3 M2BA 132 SMB 29.3 8 85.3 £616 £659
4 M2BA 132 SMB 39.7 10 84.9 £670 £731
5.5 M2BA 132 SMF 54.4 12.9 86.1 £892 £927
7.5 M2BA 160 MLA 73.7 15.6 87.6 £1,028 £1,117
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1000 r/min = 6 poles
11 M2BA 160 MLB 108 22.6 88.7 £1,379 £1,467
15 M2BA 180 MLA 147 31.7 89.7 £1,793 £1,929
18.5 M2BA 200 MLA 181 37.2 90.7 £2,211 £2,393
22 M2BA 200 MLB 215 44.1 91.0 £2,629 £2,811
30 M2BA 225 SMA 290 56.5 92.2 £3,497 £3,710
37 M2BA 250 SMA 358 69.6 92.4 £4,205 £4,448
45 M2BA 280 SA 434 83.3 92.8 £5,840 £6,215
55 M2BA 280 SB 530 101 93.3 £7,143 £7,500
75 M2BA 315 SMA 721 142 94.0 £9,572 £10,179
90 M2BA 315 SMB 866 165 94.3 £11,500 £12,108
110 M2BA 315 SMC 1058 201 94.7 £13,983 £14,590
132 M2BA 315 MLA 1270 241 94.9 £16,697 £17,304
160 M2BA 355 SMA 1540 293 94.9 £20,643 £21,715
200 M2BA 355 SMB 1925 360 95.2 £25,893 £26,786
250 M2BA 355 SMC 2409 450 95.3 £31,786 £32,858
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1500 r/min = 4 poles
0.25 M2BA 71 MA 1.74 0.65 68.3 £139 £157
0.37 M2BA 71 MB 2.5 0.88 72.4 £147 £176
0.55 M2BA 80 MA 3.7 1.45 74.5 £176 £204
0.75 M2BA 80 MD 5 1.83 81.0 £252 £277
1.1 M2BA 90 SLB 7.3 2.3 83.6 £316 £349
1.5 M2BA 90 SLD 10 3 84.3 £379 £412
2.2 M2BA 100 LC 14.4 4.7 85.9 £430 £479
3 M2BA 100 LD 19.7 6.3 86.8 £482 £531
4 M2BA 112 MB 26.5 8.2 86.8 £575 £628
5.5 M2BA 132 SMB 35.9 11.1 89.0 £736 £803
7.5 M2BA 132 SMC 49.3 14.9 89.3 £945 £1,015
11 M2BA 160 MLA 71.7 20.7 90.2 £995 £1,083
15 M2BA 160 MLB 97.9 28.4 90.6 £1,268 £1,356
18.5 M2BA 180 MLA 120 34.8 91.2 £1,456 £1,593
22 M2BA 180 MLB 143 41.7 91.6 £1,732 £1,868
30 M2BA 200 MLA 194 56.5 92.3 £2,274 £2,455
37 M2BA 225 SMA 238 68.3 93.0 £2,804 £3,016
45 M2BA 225 SMB 290 83.9 93.2 £3,410 £3,622
55 M2BA 250 SMA 355 99.8 93.5 £4,167 £4,410
75 M2BA 280 SA 482 135 94.2 £6,393 £6,750
90 M2BA 280 SMB 579 160 94.4 £7,465 £7,840
110 M2BA 315 SMA 706 194 94.7 £9,268 £9,875
132 M2BA 315 SMB 847 233 95.0 £11,179 £11,786
160 M2BA 315 SMC 1027 285 95.2 £13,518 £14,125
200 M2BA 315 MLA 1285 352 95.3 £17,161 £17,768
250 M2BA 355 SMA 1604 445 95.2 £21,411 £22,465
315 M2BA 355 SMB 2021 560 95.5 £27,143 £28,215
355 M2BA 355 SMC 2279 623 95.5 £30,715 £31,786
IE2
* Efficiency full load 100%
68 General performance aluminium motors l ABB drives and motors catalogue 2014
General performance aluminium motors, 56-250, 2, 4 & 6 poles
TEFC low voltage motors, aluminium, IP 55, IC 411, single-speed. 400 V 3-phase 50 Hz See product catalogues or www.abb.com/motors&generators for more information on products.
IE2
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
3000 r/min = 2 poles
0.09 M2AA 56 A 0.3 0.31 59.8 £118 £134
0.12 M2AA 56 B 0.4 0.4 67.2 £121 £138
0.18 M2AA 63 A 0.6 0.55 75.0 £130 £148
0.25 M2AA 63 B 0.84 0.66 78.6 £132 £150
0.37 M2AA 71 A 1.26 0.95 73.8 £141 £159
0.55 M2AA 71 B 1.88 1.29 78.4 £149 £167
0.75 M2AA 80 B 2.4 1.7 81.4 £198 £215
1.1 M2AA 80 C 3.6 2.4 8.6 £250 £287
1.5 M2AA 90 L 4.9 2.9 84.1 £297 £335
2.2 M2AA 90 LB 7.3 4.4 84.6 £367 £405
3 M2AA 100 LB 9.8 5.8 86.4 £447 £497
4 M2AA 112 MB 13.2 7.6 86.1 £529 £580
5.5 M2AA 132 SB 18 11 88.0 £693 £759
7.5 M2AA 132 SC 24.5 14 88.5 £879 £948
11 M2AA 160 MLA 35.9 19.8 89.8 £1,067 £1,180
15 M2AA 160 MLB 48.8 25.4 91.1 £1,321 £1,417
18.5 M2AA 160 MLC 60.2 32.9 91.0 £1,584 £1,682
22 M2AA 180 MLA 71.6 38.1 91.5 £1,872 £1,998
30 M2AA 200 MLA 97.1 52.7 92.2 £2,422 £2,568
37 M2AA 200 MLB 119 63.4 92.5 £2,974 £3,138
45 M2AA 225 SMA 145 77.6 93.0 £4,546 £4,741
55 M2AA 250 SMA 177 93.9 93.9 £5,319 £5,531
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1000 r/min = 6 poles
0.09 M2AA 63 A 0.94 0.49 47.1 £138 £156
0.12 M2AA 63 B 1.25 0.51 57.5 £142 £161
0.18 M2AA 71 A 1.94 0.61 59.5 £155 £175
0.25 M2AA 71 B 2.6 0.79 64.0 £177 £200
0.37 M2AA 80 A 3.9 1.07 68.0 £195 £220
0.55 M2AA 80 B 5.8 1.58 68.7 £218 £247
0.75 M2AA 90 LB 7.7 1.96 77.6 £229 £258
1.1 M2AA 90 LD 11.2 3 78.2 £269 £302
1.5 M2AA 100 LC 15.1 3.6 80.3 £337 £375
2.2 M2AA 112 MB 21.9 5.3 81.9 £455 £497
3 M2AA 132 S 29.8 7.9 83.3 £598 £639
4 M2AA 132 MB 39.1 9.5 86.4 £650 £709
5.5 M2AA 132 MC 54.4 13.7 86.1 £736 £775
7.5 M2AA 160 MLA 73.7 15.6 87.6 £1,102 £1,188
11 M2AA 160 MLB 108 22.6 88.7 £1,500 £1,584
15 M2AA 180 MLA 147 31.7 89.7 £1,938 £2,066
18.5 M2AA 200 MLA 181 37.2 90.7 £2,292 £2,422
22 M2AA 200 MLB 215 44.1 91.0 £2,389 £2,535
30 M2AA 225 SMA 290 56.5 92.2 £3,951 £4,144
37 M2AA 250 SMA 358 69.6 92.4 £4,692 £4,900
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1500 r/min = 4 poles
0.06 M2AA 56 A 0.42 0.25 51.1 £114 £129
0.09 M2AA 56 B 0.62 0.37 55.5 £117 £132
0.12 M2AA 63 A 0.81 0.46 65.5 £126 £144
0.18 M2AA 63 B 1.24 0.62 67.3 £128 £146
0.25 M2AA 71 A 1.74 0.72 65.1 £134 £152
0.37 M2AA 71 B 2.5 0.96 69.7 £142 £170
0.55 M2AA 80 A 3.8 1.41 72.8 £170 £198
0.75 M2AA 80 D 5 1.65 79.8 £244 £268
1.1 M2AA 90 LB 7.3 2.4 83.7 £306 £338
1.5 M2AA 90 D 9.9 3.3 84.2 £367 £400
2.2 M2AA 100 LC 14.4 4.6 86.4 £417 £465
3 M2AA 100 D 19.8 6.3 85.7 £467 £515
4 M2AA 112 MB 26.4 8.8 86.7 £558 £609
5.5 M2AA 132 M 35.8 11.2 89.0 £714 £779
7.5 M2AA 132 MA 49 15.3 89.1 £917 £985
11 M2AA 160 MLA 71.7 20.7 90.2 £1,076 £1,189
15 M2AA 160 MLB 97.9 28.4 90.5 £1,345 £1,430
18.5 M2AA 180 MLA 120 34.8 91.2 £1,616 £1,729
22 M2AA 180 MLB 143 41.7 91.6 £1,904 £2,002
30 M2AA 200 MLA 190 56.5 92.3 £2,373 £2,486
37 M2AA 225 SMA 238 68.3 93.0 £3,193 £3,418
45 M2AA 225 SMB 290 83.9 93.2 £3,886 £4,112
55 M2AA 250 SMA 355 99.8 93.5 £4,643 £4,835
* Efficiency full load 100%
Process performance cast iron motors l ABB drives and motors catalogue 2014 69
Process performance cast iron motors
TEFC low voltage motors, cast iron frame, IP 55, IC 411, single-speed. 400 V 3-phase 50 HzSee product catalogues or www.abb.com/motors&generators for more information on products.
IE2
What is a process performance motor? Process performance motors are the flagship of ABB’s standard low voltage motors. This range provides the most comprehensive, versatile set of motors for the process industries and heavy-duty applications which are dependent on continuous reliability, lowest possible environmental impact and life cycle costs. Their superior ability to perform reliably and efficiently, continuously and even under the most challenging circumstances, ensures that they power their way through the toughest tasks and conditions. As such they come with a three years warranty that can be extended to five years.
Where can it be used?– End-users in continuous process industries– Project OEMs– EPCs– Demanding industries: - pulp and paper - metals - minerals and mining
Highlights– All variant codes possible for process industry– Application knowledge and engineering– With three years warranty and option to extend to five years– IE2 efficiency, IE3 available
70 Process performance cast iron motors l ABB drives and motors catalogue 2014
Process performance cast iron motors, 71-450, 2 poles
TEFC low voltage motors, cast iron frame, IP 55, IC 411, single-speed. 400 V 3-phase 50 HzSee product catalogues or www.abb.com/motors&generators for more information on products.
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
3000 r/min = 2 poles
0.37 M3BP 71 MA 1.27 0.96 69.2 £242 £277
0.55 M3BP 71 MB 1.86 1.27 73.2 £286 £321
0.75 M3BP 80 MB 2.4 1.81 80.6 £329 £366
1.1 M3BP 80 MC 3.6 2.4 81.8 £346 £381
1.5 M3BP 90 SLB 4.9 3.0 82.2 £364 £402
2.2 M3BP 90 SLC 7.2 4.3 84.7 £453 £489
3 M3BP 100 LB 9.7 5.9 85.2 £532 £591
4 M3BP 112 MB 13.1 7.7 86.1 £684 £767
5.5 M3BP 132 MB 18.3 10.4 88.0 £828 £897
7.5 M3BP 132 SMC 24.7 14.5 88.6 £999 £1,090
11 M3BP 160 MLA 35.7 19.2 90.7 £1,126 £1,240
15 M3BP 160 MLB 48.8 26.0 91.5 £1,338 £1,459
18.5 M3BP 160 MLC 60.2 31.5 92.0 £1,633 £1,740
22 M3BP 160 MLA 71.6 38.0 91.7 £1,913 £1,990 HO
22 M3BP 180 MLA 71.1 39.5 92.2 £1,990 £2,082
30 M3BP 160 MLE 97.9 51.8 91.7 £2,407 £2,547 HO
30 M3BP 180 MLB 97.1 53.0 92.8 £2,407 £2,547 HO
30 M3BP 200 MLA 96.9 51.6 93.1 £2,577 £2,685
37 M3BP 200 MLB 119 63.5 93.4 £3,753 £3,907
45 M3BP 200 MLC 145 79.1 93.3 £4,313 £4,471 HO
45 M3BP 225 SMA 145.0 78.8 93.6 £4,794 £4,962
55 M3BP 200 MLD 177.0 95.0 93.8 £5,491 £5,709 HO
55 M3BP 225 SMB 177 96.0 93.9 £5,491 £5,709 HO
55 M3BP 250 SMA 177.0 95.8 94.1 £5,738 £5,927
75 M3BP 225 SMC 241.0 136.0 94.5 £6,837 £7,049 HO
75 M3BP 280 SMA 240 130 94.3 £7,333 £7,753
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
3000 r/min = 2 poles
90 M3BP 250 SMC 289.0 153.0 95.0 £7,950 £8,141 HO
90 M3BP 280 SMB 288 152 94.6 £8,348 £8,601
110 M3BP 280 SMC 352.0 185.0 95.1 £10,082 £10,425 HO
110 M3BP 315 SMA 352 194 94.9 £10,996 £11,357
132 M3BP 315 SMB 422 227 95.1 £12,156 £12,529
160 M3BP 315 SMC 512 271 95.4 £13,893 £14,269
200 M3BP 315 MLA 640 335 95.7 £19,341 £21,223
250 M3BP 315 LKA 801.0 423.0 95.7 £22,935 £23,619 HO
250 M3BP 355 SMA 800 423 95.7 £24,474 £25,672
315 M3BP 315 LKC 1009.0 533.0 95.7 £28,754 £29,438 HO
315 M3BP 355 SMB 1009 533 95.7 £30,805 £32,004
355 M3BP 355 SMC 1136 608 95.7 £34,744 £35,941
400 M3BP 355 MLA 1280 677 96.9 £38,849 £40,047
450 M3BP 355 MLB 1440 743 97.1 £44,324 £45,523
500 M3BP 355 LKA 1601 827 96.9 £47,234 £48,431
560 M3BP 355 LKB 1792 925 97.0 £53,052 £54,250
560 M3BP 400 LA 1789 934 97.2 £55,619 £57,159
560 M3BP 400 LKA 1789 934 97.2 £57,140 £58,679
630 M3BP 400 LKB 2014 1048 97.4 £63,299 £64,839
630 M3BP 400 LB 2014 1048 97.4 £61,778 £63,319
710 M3BP 400 LC 2269 1180 97.5 £69,651 £71,189
710 M3BP 400 LKC 2269 1180 97.5 £71,171 £72,708
800 M3BP 450 LA 2554 1349 97.2 £78,010 £80,400
900 M3BP 450 LB 2874 1517 97.3 £85,030 £87,640
HO = High-output design
* Efficiency full load 100%
IE2
Process performance cast iron motors l ABB drives and motors catalogue 2014 71
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1500 r/min = 4 poles
0.25 M3BP 71 MA 1.74 0.65 68.3 £225 £263
0.37 M3BP 71 MB 2.5 0.88 72.4 £267 £305
0.55 M3BP 80 MA 3.7 1.45 74.5 £310 £348
0.75 M3BP 80 MD 5.0 1.83 81.0 £316 £353
1.1 M3BP 90 SLB 7.3 2.3 83.6 £346 £381
1.5 M3BP 90 SLD 10.0 3.0 84.3 £417 £454
2.2 M3BP 100 LC 14.4 4.7 85.9 £473 £532
3 M3BP 100 LD 19.7 6.3 86.8 £538 £602
4 M3BP 112 MB 26.5 8.2 86.8 £668 £720
5.5 M3BP 132 SMB 35.9 11.1 89.0 £850 £910
7.5 M3BP 132 SMC 49.3 14.9 89.3 £1,047 £1,107
11 M3BP 160 MLA 71.6 20.9 90.4 £1,117 £1,230
15 M3BP 160 MLB 97.4 28.5 91.4 £1,392 £1,530
18.5 M3BP 160 MLC 120 34.7 91.4 £1,586 £1,710 HO
18.5 M3BP 180 MLA 119 34.5 91.9 £1,666 £1,773
22 M3BP 160 MLD 143 40.7 91.6 £1,946 £2,014 HO
22 M3BP 180 MLB 142 40.9 92.4 £1,990 £2,066
30 M3BP 180 MLC 194 56.5 92.3 £2,329 £2,469 HO
30 M3BP 200 MLA 193 55.3 93.2 £2,609 £2,749
37 M3BP 200 MLB 238 67.2 93.4 £3,229 £3,431 HO
37 M3BP 225 SMA 238 68.0 93.4 £3,508 £3,694
45 M3BP 200 MLC 290 83.6 93.6 £3,922 £4,092 HO
45 M3BP 225 SMB 290 81.3 93.9 £4,111 £4,313
55 M3BP 225 SMC 355 99.3 94.0 £4,825 £5,059 HO
55 M3BP 250 SMA 354 98.9 94.4 £4,962 £5,198
73 M3BP 225 SMD 472 132 93.6 £5,777 £6,106 HO
75 M3BP 250 SMB 484 134 94.4 £5,969 £6,359 HO
75 M3BP 280 SMA 482 134 94.5 £6,251 £6,627
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1500 r/min = 4 poles
90 M3BP 250 SMC 581 163 94.7 £7,367 £7,526 HO
90 M3BP 280 SMB 579 159 94.7 £7,504 £7,896
110 M3BP 280 SMC 707 194 95.1 £8,556 £8,946 HO
110 M3BP 315 SMA 706 194 95.1 £9,259 £9,667
132 M3BP 315 SMB 847 232 95.4 £10,935 £11,310
160 M3BP 315 SMC 1027 284 95.6 £12,781 £13,156
200 M3BP 315 MLA 1285 351 95.6 £18,167 £18,637
250 M3BP 315 LKA 1605 438 95.7 £19,887 £20,515 HO
250 M3BP 355 SMA 1604 437 95.9 £21,454 £22,081
280 M3BP 315 LKB 1798 484 95.8 £24,585 £25,210 HO
315 M3BP 315 LKC 2021 551 95.8 £26,933 £27,559 HO
315 M3BP 355 SMB 2021 551 95.9 £28,500 £29,439
355 M3BP 355 SMC 2279 621 95.9 £30,380 £31,317
400 M3BP 355 MLA 2565 705 96.3 £34,449 £35,075
450 M3BP 355 MLB 2884 780 96.8 £38,989 £39,303
500 M3BP 355 LKA 3204 865 97.0 £43,218 £43,530
560 M3BP 355 LKB 3588 981 96.9 £47,132 £47,444
560 M3BP 400 LKA 3586 982 96.8 £49,480 £50,106
560 M3BP 400 LA 3586 982 96.8 £49,480 £50,106
630 M3BP 400 LB 4034 1077 97.0 £54,960 £55,585
630 M3BP 400 LKB 4034 1077 97.0 £57,672 £59,210
710 M3BP 400 LC 4547 1227 97.1 £65,029 £66,568
710 M3BP 400 LKC 4547 1227 97.1 £66,552 £68,090
800 M3BP 450 LA 5120 1385 96.9 £74,540 £76,260
900 M3BP 450 LB 5760 1555 97.1 £81,994 £83,886
1000 M3BP 450 LC 6404 1726 97.2 £90,193 £92,275
HO = High-output design
Process performance cast iron motors, 71-450, 4 poles
TEFC low voltage motors, cast iron frame, IP 55, IC 411, single-speed. 400 V 3-phase 50 HzSee product catalogues or www.abb.com/motors&generators for more information on products.
IE2
* Efficiency full load 100%
72 Process performance cast iron motors l ABB drives and motors catalogue 2014
Process performance cast iron motors, 71-450, 6 & 8+ poles
TEFC low voltage motors, cast iron frame, IP 55, IC 411, single-speed. 400 V 3-phase 50 HzSee product catalogues or www.abb.com/motors&generators for more information on products.
IE2
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1000 r/min = 6 poles
0.18 M3BP 71 MA 1.9 0.57 63.7 £238 £256
0.25 M3BP 71 MB 2.6 0.77 67.2 £263 £302
0.37 M3BP 80 MA 3.8 1.09 71.0 £312 £350
0.55 M3BP 80 MB 5.7 1.51 73.9 £315 £351
0.75 M3BP 90 SLC 7.4 2.3 78.7 £348 £382
1.1 M3BP 90 SLE 11.2 3.0 78.2 £417 £454
1.5 M3BP 100 L 15.0 3.8 82.2 £518 £573
2.2 M3BP 112 MB 22.1 5.5 82.5 £639 £696
3 M3BP 132 SMB 29.3 8.0 85.3 £828 £891
4 M3BP 132 SMC 39.7 10.0 84.9 £939 £996
5.5 M3BP 132 SMF 54.4 12.9 86.1 £1,014 £1,077
7.5 M3BP 160 MLA 73.4 15.4 88.6 £1,112 £1,222
11 M3BP 160 MLB 108 22.5 89.3 £1,619 £1,735
15 M3BP 160 MLC 147 31.3 89.7 £1,832 £1,956 HO
15 M3BP 180 MLA 146 31.0 90.5 £1,990 £2,129
18.5 M3BP 180 MLB 181 37.2 90.7 £2,299 £2,423 HO
18.5 M3BP 200 MLA 178 36.4 91.6 £2,375 £2,533
22 M3BP 200 MLB 212 42.0 92.0 £2,639 £2,812
30 M3BP 200 MLC 290 56.7 92.0 £3,772 £3,973 HO
30 M3BP 225 SMA 290 56.2 92.7 £4,145 £4,344
37 M3BP 225 SMB 358 69.1 93.1 £4,655 £4,808 HO
37 M3BP 250 SMA 357 69.9 93.1 £4,855 £5,074
45 M3BP 250 SMB 434 83.7 93.4 £6,824 £7,041 HO
45 M3BP 280 SMA 434 82.7 93.4 £7,114 £7,348
55 M3BP 250 SMC 531 101 93.2 £7,526 £7,791 HO
55 M3BP 280 SMB 530 100 93.8 £7,741 £7,991
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
750 r/min = 8 poles
75 M3BP 315 SMB 966 140 93.7 £11,527 £12,124
90 M3BP 315 SMC 1159 168 94.0 £14,128 £14,722
110 M3BP 315 MLA 1419 203 94.0 £17,228 £17,854
132 M3BP 315 LKA 1703 243 94.1 £18,444 £18,974 HO
132 M3BP 355 SMA 1694 251 94.7 £20,670 £21,454
150 M3BP 315 LKB 1933 276 94.3 £20,670 £21,454 HO
160 M3BP 315 LKC 2064 295 94.2 £21,836 £22,578 HO
160 M3BP 355 SMB 2053 303 95.2 £23,488 £24,585
200 M3BP 355 SMC 2570 378 95.3 £32,571 £33,511
250 M3BP 355 MLB 3213 472 95.4 £40,554 £41,493
315 M3BP 355 LKB 4053 595 95.5 £49,012 £49,792
315 M3BP 400 LA 4043 584 96.1 £51,987 £52,767
315 M3BP 400 LKA 4043 584 96.1 £51,987 £52,767
355 M3BP 400 LB 4562 641 96.2 £58,718 £59,031
355 M3BP 400 LKB 4562 641 96.2 £58,718 £59,031
400 M3BP 400 LC 5134 731 96.3 £65,135 £65,448
400 M3BP 400 LKC 5134 731 96.3 £65,135 £65,448
450 M3BP 450 LA 5775 813 96.2 £68,370 £71,105
500 M3BP 450 LB 6417 902 96.3 £76,108 £79,153
560 M3BP 450 LC 7187 1022 96.4 £82,680 £85,988
630 M3BP 450 LD 8075 1162 96.6 £91,160 £94,807
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1000 r/min = 6 poles
75 M3BP 280 SMC 723 136 94.2 £8,900 £9,259 HO
75 M3BP 315 SMA 721 139 94.4 £9,524 £9,917
90 M3BP 315 SMB 866 163 94.8 £11,198 £11,794
110 M3BP 315 SMC 1059 201 95.0 £13,612 £14,206
132 M3BP 315 MLA 1271 240 95.3 £16,759 £17,854
160 M3BP 315 LKA 1540 291 95.3 £18,793 £19,418 HO
160 M3BP 355 SMA 1538 291 95.4 £19,106 £20,203
180 M3BP 315 LKB 1732 328 95.3 £20,985 £21,611 HO
200 M3BP 315 LKC 1931 355 95.4 £23,332 £23,960 HO
200 M3BP 355 SMB 1923 359 95.7 £23,802 £24,898
250 M3BP 355 SMC 2404 454 95.7 £29,439 £30,536
315 M3BP 355 MLB 3032 572 95.7 £35,389 £36,485
355 M3BP 355 LKA 3417 645 95.7 £42,123 £43,218
400 M3BP 355 LKB 3850 724 96.0 £44,313 £45,253
400 M3BP 400 LA 3846 731 96.2 £46,973 £50,261
400 M3BP 400 LKA 3846 731 96.2 £46,973 £50,261
450 M3BP 400 LKB 4323 819 96.6 £53,082 £56,839
450 M3BP 400 LKB 4323 819 96.6 £53,082 £56,839
500 M3BP 400 LC 4808 900 96.6 £58,875 £63,100
500 M3BP 400 LKC 4808 900 96.6 £58,875 £63,100
560 M3BP 400 LD 5385 981 96.9 £65,294 £69,991
560 M3BP 400 LKD 5385 981 96.9 £65,294 £69,991
630 M3BP 450 LA 6052 1119 96.7 £66,727 £71,020
710 M3BP 450 LB 6814 1244 96.9 £71,762 £75,790
800 M3BP 450 LC 7677 1418 96.9 £79,500 £84,270
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
750 r/min = 8 poles
0.18 M3BP 80 MA 2.4 0.73 57.4 £214 £250
0.25 M3BP 80 MB 3.5 0.90 61.5 £244 £281
0.37 M3BP 90 SLB 5.0 1.49 66.3 £296 £330
0.55 M3BP 90 SLC 8.0 1.91 61.8 £363 £395
0.75 M3BP 100 LA 10.0 2.3 74.0 £435 £480
1.1 M3BP 100 LB 15.1 3.1 76.0 £555 £600
1.5 M3BP 112 M 20.7 4.1 74.4 £670 £724
2.2 M3BP 132 SMA 29.3 6.0 79.7 £860 £925
3 M3BP 132 SMB 40.0 8.4 79.9 £1,026 £1,095
4 M3BP 160 MLA 52.4 10.2 84.1 £1,141 £1,261
5.5 M3BP 160 MLB 72.3 13.9 84.7 £1,203 £1,314
7.5 M3BP 160 MLC 98.5 19.3 86.1 £1,454 £1,569
11 M3BP 180 MLA 143 27.3 86.8 £2,204 £2,299
15 M3BP 200 MLA 194 32.4 90.2 £2,672 £2,840
18.5 M3BP 225 SMA 239 40.1 91.0 £3,460 £3,614
22 M3BP 225 SMB 284 46.8 91.6 £4,236 £4,436
30 M3BP 250 SMA 386 66.0 92.4 £5,088 £5,337
37 M3BP 280 SMA 476 73.8 92.7 £7,348 £7,598
45 M3BP 280 SMB 579 89.3 93.2 £7,801 £8,069
55 M3BP 280 SMC 708 106 93.4 £8,900 £9,243 HO
55 M3BP 315 SMA 707 104 93.4 £9,493 £9,869
HO = High-output design * Efficiency full load 100% + IE2 not applicable to 8-pole
Process performance aluminium motors l ABB drives and motors catalogue 2014 73
IE2Process performance aluminium motors, 63-280 2, 4, 6 & 8+ poles
TEFC low voltage motors, aluminium, IP 55, IC 411, single-speed. 400 V 3-phase 50 Hz See product catalogues or www.abb.com/motors&generators for more information on products.
High output design motors available on request.
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
3000 r/min = 2 poles
0.18 M3AA 63 A 0.60 0.55 75.0 £137 £156
0.25 M3AA 63 B 0.84 0.66 78.6 £139 £158
0.37 M3AA 71 A 1.26 0.95 73.8 £149 £167
0.55 M3AA 71 B 1.88 1.29 78.4 £157 £176
0.75 M3AA 80 B 2.4 1.70 80.6 £208 £226
1.1 M3AA 80 C 3.6 2.4 80.6 £263 £302
1.5 M3AA 90 L 4.9 2.9 84.1 £312 £352
2.2 M3AA 90 LB 7.3 4.4 84.6 £386 £426
3 M3AA 100 LB 9.8 5.8 86.4 £470 £522
4 M3AA 112 MB 13.2 7.6 86.1 £556 £609
5.5 M3AA 132 SB 18.0 11.0 88.0 £728 £797
7.5 M3AA 132 SC 24.5 14.0 88.5 £923 £996
11 M3AA 160 MLA 35.7 19.2 90.7 £1,134 £1,230
15 M3AA 160 MLB 48.8 26.0 91.5 £1,473 £1,582
18.5 M3AA 160 MLC 60.2 31.5 92.0 £1,768 £1,876
22 M3AA 180 MLA 71.1 39.5 92.2 £2,016 £2,155
30 M3AA 200 MLA 96.9 51.6 93.1 £2,544 £2,697
37 M3AA 200 MLB 119.0 63.5 93.4 £3,318 £3,504
45 M3AA 225 SMA 145.0 78.8 93.6 £4,774 £4,979
55 M3AA 250 SMA 177.0 95.8 94.1 £5,585 £5,808
75 M3AA 280 SMA 241.0 128.0 94.5 £6,894 £7,073
90 M3AA 280 SMB 289.0 153.0 95.0 £8,077 £8,290
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1500 r/min = 4 poles
0.12 M3AA 63 A 0.81 0.46 65.5 £133 £152
0.18 M3AA 63 B 1.24 0.62 67.3 £135 £154
0.25 M3AA 71 A 1.74 0.72 65.1 £141 £160
0.37 M3AA 71 B 2.5 0.96 69.7 £150 £179
0.55 M3AA 80 A 3.8 1.41 72.8 £179 £208
0.75 M3AA 80 E 5.0 1.8 79.9 £257 £282
1.1 M3AA 90 LB 7.3 2.4 83.7 £322 £355
1.5 M3AA 90 LD 9.9 3.3 84.2 £386 £420
2.2 M3AA 100 LC 14.4 4.6 87.1 £438 £489
3 M3AA 100 LD 19.8 6.3 85.7 £491 £541
4 M3AA 112 MB 26.4 8.8 86.7 £586 £640
5.5 M3AA 132 M 35.8 11.2 89.0 £750 £818
7.5 M3AA 132 MA 49.0 15.3 89.1 £963 £1,035
11 M3AA 160 MLA 71.6 20.9 90.4 £1,157 £1,253
15 M3AA 160 MLB 97.4 28.5 91.4 £1,501 £1,596
18.5 M3AA 180 MLA 119 34.5 91.9 £1,706 £1,845
22 M3AA 180 MLB 142 40.9 92.4 £2,047 £2,186
30 M3AA 200 MLA 193 55.3 93.2 £2,636 £2,822
37 M3AA 225 SMA 238 68.0 93.4 £3,353 £3,589
45 M3AA 225 SMB 290 81.3 93.9 £4,081 £4,318
55 M3AA 250 SMA 354 98.9 94.4 £4,876 £5,077
75 M3AA 280 SMA 484 135.0 94.3 £6,251 £6,466
90 M3AA 280 SMB 581 163 94.7 £7,335 £7,534
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1000 r/min = 6 poles
0.09 M3AA 63 A 0.94 0.49 47.1 £145 £164
0.12 M3AA 63 B 1.25 0.51 57.5 £150 £170
0.18 M3AA 71 A 1.94 0.61 59.5 £163 £184
0.25 M3AA 71 B 2.6 0.79 64.0 £186 £210
0.37 M3AA 80 A 3.9 1.07 68.0 £205 £231
0.55 M3AA 80 B 5.8 1.58 68.7 £229 £260
0.75 M3AA 90 LB 7.7 1.96 77.6 £280 £307
1.1 M3AA 90 LD 11.2 3.0 78.2 £345 £368
1.5 M3AA 100 LC 15.1 3.6 80.3 £395 £426
2.2 M3AA 112 MB 21.9 5.3 81.9 £496 £529
3 M3AA 132 S 29.8 7.9 83.3 £628 £671
4 M3AA 132 MB 39.1 9.5 86.4 £769 £807
5.5 M3AA 132 MC 54.4 13.7 86.1 £950 £979
7.5 M3AA 160 MLA 73.4 15.4 88.6 £1,230 £1,326
11 M3AA 160 MLB 108 22.5 89.3 £1,675 £1,768
15 M3AA 180 MLA 146 31.0 90.5 £2,093 £2,233
18.5 M3AA 200 MLA 178 36.4 91.6 £2,512 £2,698
22 M3AA 200 MLB 212 42.0 92.0 £2,962 £3,148
30 M3AA 225 SMA 290 56.2 92.7 £4,149 £4,352
37 M3AA 250 SMA 357 69.9 93.1 £4,931 £5,179
45 M3AA 280 SMA 434 82.9 93.2 £5,778 £5,990
55 M3AA 280 SMB 531 101 93.2 £7,068 £7,458
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
750 r/min = 8 poles
0.09 M3AA 71 A 1.27 0.46 48.4 £165 £182
0.12 M3AA 71 B 1.72 0.56 51.5 £184 £208
0.18 M3AA 80 A 2.4 0.74 57.2 £208 £234
0.25 M3AA 80 B 3.4 0.97 61.4 £217 £245
0.37 M3AA 90 S 5.0 1.66 59.4 £290 £323
0.55 M3AA 90 L 7.9 2.3 59.1 £355 £388
0.75 M3AA 100 LA 9.9 3.2 70.7 £422 £465
1.1 M3AA 100 LB 15.1 3.1 76.0 £526 £568
1.5 M3AA 112 M 20.7 4.1 74.4 £636 £686
2.2 M3AA 132 S 29.3 6.2 77.7 £807 £868
3 M3AA 132 M 40.0 8.5 79.3 £942 £1,006
4 M3AA 160 MLA 52.4 10.2 84.1 £1,134 £1,230
5.5 M3AA 160 MLB 72.3 13.9 84.7 £1,411 £1,504
7.5 M3AA 160 MLC 98.5 19.3 86.1 £1,690 £1,783
11 M3AA 180 MLA 144 23.9 88.5 £2,233 £2,372
15 M3AA 200 MLA 194 32.4 90.2 £2,807 £2,993
18.5 M3AA 225 SMA 239 40.1 91.0 £3,442 £3,659
22 M3AA 225 SMB 284 46.8 91.6 £4,199 £4,385
30 M3AA 250 SMA 386 66.0 92.4 £5,011 £5,215
37 M3AA 280 SMA 477 78.1 92.3 £5,752 £5,982
* Efficiency full load 100%+ IE2 not applicable to 8-pole
74 Premium efficiency process performance motors l ABB drives and motors catalogue 2014
Premium efficiency process performance motorsInnovative thinking – highest efficiency and reliability with off-the-shelf availability
ABB’s new generation process performance premium efficiency motors deliver maximum value over their entire life cycle. Their IE3 efficiency rating makes them an ideal environmental choice for motor users seeking to save energy and reduce their carbon footprint.
New levels of efficiencyRising energy costs and increasing concerns about the environment are focusing attention on ways to further reduce energy consumption. Motor-driven systems account for65 percent of all the electricity used in industry, givingmotors a major role to play in efforts to reduce energy use.
Cutting-edge design, quality materials and advanced manufacturing techniques make ABB’s process performance premium efficiency motors extremely reliable and energy efficient, even under the most challenging conditions.
Future-proof solutionABB motors comply with the latest efficiency standards and requirements. ABB closely follows developments in the global regulatory environment and ensures that its products stay ahead.
Process performance premium efficiency motors with the IE3 efficiency rating already meet the requirements of the EU MEPS (European Minimum Energy Performance Standard) scheme set to come into force in 2015. These motors are available now for delivery from stock.
Motors for the super premium IE4 efficiency class are also available from 160 to 355 frame size.
Excellent all-round performanceProcess performance premium efficiency motors offer enhanced operating performance, low starting currents, and an excellent torque curve. They produce less noise, are subject to lower mechanical stresses, and run cooler than less efficient motors.
Cooler running is a big advantage. Reducing the temperature of the bearings and windings extends the lubrication intervals and increases the useful life of the motor. This translates into higher reliability, easier maintenance, and a longer life cycle – factors which reduce the overall cost of ownership. As a result, ABB’s process performance premium efficiency motors have longer warranties than many other types of motor.
With an extensive range of accessories available, ABB’s process performance premium efficiency motors are particularly suitable for industrial and OEM use. They are ideal for all applications demanding efficiency and reliability, especially under challenging conditions.
Motor types M3BP & M3AA
Frame sizes 80-355 & 80-250
Output range 0.75 kW to 355 kW
Poles 2 to 6 poles
Frame material Cast iron & aluminium
Voltage up to 690 V, 50 & 60 Hz
Premium efficiency process performance cast iron motors l ABB drives and motors catalogue 2014 75
Premium efficiency process performance cast iron motors, 160-355, 2, 4 & 6 poles
TEFC low voltage motors, cast iron frame, IP 55, IC 411, single-speed. 400 V 3-phase 50 HzSee product catalogues or www.abb.com/motors&generators for more information on products.
IE3
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
3000 r/min = 2 poles
11 M3BP 160 MLA 35.6 18.7 92.1 £1,734 £1,880
15 M3BP 160 MLB 48.6 25.4 92.6 £2,257 £2,428
18.5 M3BP 160 MLC 60 30.8 93.1 £2,712 £2,864
22 M3BP 180 MLA 71 37.4 93.2 £3,054 £3,262
30 M3BP 200 MLA 96.8 51 94.2 £3,812 £4,096
37 M3BP 200 MLB 119 61.9 94.7 £5,007 £5,272
45 M3BP 225 SMA 144 76.8 95.0 £6,031 £6,353
55 M3BP 250 SMA 176 93.6 95.2 £7,320 £7,680
75 M3BP 280 SMB 240 130 95.5 £8,855 £9,362
90 M3BP 280 SMC 288 154 95.7 £10,082 £10,387
110 M3BP 315 SMB 352 190 95.9 £13,279 £13,715
132 M3BP 315 SMC 422 225 95.9 £14,679 £15,130
160 M3BP 315 MLA 512 267 96.1 £16,776 £17,231
200 M3BP 315 MLB 640 333 96.2 £23,356 £25,628
200 M3BP 355 SMA 640 337 96.2 £28,350 £31,080
250 M3BP 315 LKB 800 411 96.3 £27,720 £30,450
250 M3BP 355 SMB 800 416 96.3 £29,554 £31,000
315 M3BP 355 SMC 1008 529 96.4 £37,198 £38,646
355 M3BP 355 MLA 1136 589 96.5 £41,954 £43,400
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1000 r/min = 6 poles
7.5 M3BP 160 MLA 73 15.2 90.8 £1,880 £2,030
11 M3BP 160 MLB 107 23.5 91.2 £2,560 £2,712
15 M3BP 180 MLA 146 30.4 92.2 £3,186 £3,395
18.5 M3BP 200 MLA 178 37.3 92.9 £3,793 £4,059
22 M3BP 200 MLB 212 43 93.3 £4,457 £4,741
30 M3BP 225 SMA 289 56.8 94.1 £6,107 £6,429
37 M3BP 250 SMA 356 68 94.5 £7,320 £7,680
45 M3BP 280 SMB 433 79.6 94.8 £8,592 £8,874
55 M3BP 280 SMC 530 97 95.1 £9,349 £9,650
75 M3BP 315 SMC 721 135 95.3 £11,501 £11,976
90 M3BP 315 SMD 864 163 95.5 £13,522 £14,243
110 M3BP 315 MLB 1057 197 95.5 £16,437 £17,154
132 M3BP 315 LKA 1269 239 95.7 £20,237 £21,560
160 M3BP 315 LKC 1537 290 95.9 £22,910 £23,448
160 M3BP 355 SMB 1535 290 95.9 £23,617 £24,921
200 M3BP 355 SMC 1919 362 96.0 £29,558 £30,717
250 M3BP 355 MLB 2399 452 96.0 £36,368 £37,527
315 M3BP 355 LKA 3026 570 96.0 £43,612 £44,916
355 M3BP 355 LKB 3407 667 96.0 £52,016 £53,175
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1500 r/min = 4 poles
11 M3BP 160 MLA 71.3 20.4 92.3 £1,770 £1,916
15 M3BP 160 MLB 97.1 27.8 92.7 £2,295 £2,447
18.5 M3BP 180 MLA 119 34.9 93.3 £2,598 £2,807
22 M3BP 180 MLB 141 41.5 93.3 £3,110 £3,319
30 M3BP 200 MLA 193 54.6 94.4 £3,964 £4,248
37 M3BP 225 SMA 238 65.4 94.9 £4,817 £5,139
45 M3BP 225 SMB 289 80.2 95.2 £5,822 £6,144
55 M3BP 250 SMA 353 97.8 95.4 £7,017 £7,396
75 M3BP 280 SMB 481 133 95.7 £7,549 £8,004
90 M3BP 280 SMC 577 159 95.9 £9,062 £9,536
110 M3BP 315 SMC 704 193 96.3 £11,181 £11,674
132 M3BP 315 SMD 845 232 96.4 £13,205 £13,658
160 M3BP 315 MLB 1026 278 96.4 £15,434 £15,887
200 M3BP 315 LKB 1281 343 96.5 £20,176 £21,938
200 M3BP 355 SMA 1281 343 96.5 £21,410 £22,938
250 M3BP 315 LKC 1601 429 96.6 £24,402 £24,612
250 M3BP 355 SMB 1601 249 96.6 £25,907 £26,664
315 M3BP 355 SMC 2017 553 96.7 £34,414 £35,548
355 M3BP 355 MLA 2273 616 96.7 £36,684 £37,816
* Efficiency full load 100%Range available from 1.1 to 7.5 for 2 pole0.55 to 7.5 - 4 pole, price on request
76 Motors for hazardous areas l ABB drives and motors catalogue 2014
Classification of explosive atmospheres according to CENELEC and IEC
Explosive atmospheres
There are systems in place worldwide to classify explosive atmospheres by zones, according to the risk posed by explosive gas (‘G”) or dust (“D”).
The following standards define areas according to the presence of gas or dust in the atmosphere:
IEC/EN 60079-10-1 GasIEC/EN 60079-10-2 Dust
Zone 2 (“G”) / 22 (“D”)Abnormal conditionPresence of explosive atmosphereonly by accident, but not during normal duty Equipment protection level “c” required
M00
0176
M00
0169
M00
0168
Zone 1 (“G”) / 21 (“D”)OccasionallyIncidental presence of explosive atmosphere during normal duty Equipment protection level “b” required
Equipment protection level“a” required
Zone 0 (“G”) / 20 (“D”)ContinouslyPermanent presence of explosive atmosphere
CE... II 2 G Ex d/Ex de
CE... II 2 G Ex e
CE... II 2 G Ex p
CE... II 2 D Ex tD A21
CE... II 3 G Ex nA
CE... II 3 D Ex tD A22
Ex d(e) II... Ex e II... Ex p II... Ex t III...
Ex nA II... Ex t III...
GbGbGbDb
GcDc
Standard Installation
IEC 60079-0 Zone acc. to
EN 60079-0 IEC 60079-10-x
EN 60079-10-x
Group EPL Protection level Zones
I Ma very high NA
(Mines) Mb high
II Ga very high 0
(Gas) Gb high 1
Gc enhanced 2
III Da very high 20
(Dust) Db high 21
Dc enhanced 22
Atex Directive Main motor
94/9/EC Protection
Types
Equipment group Equipment category
I M1 NA
(Mines) M2
II 1G NA
(Surface) 2G Ex d/Ex de, Ex p, Ex e
3G Ex nA
1D NA
2D Ex tb IP 65
3D Ex tc, IP 65/IP 55
Motors for hazardous areas l ABB drives and motors catalogue 2014 77
Clasification
Marking of equipment protection for gas according to ATEX
Marking of equipment protection for gas according to IEC
Gas classification Gas subdivision
CE marking
Identifi cation
of the notifi ed body
responsible for the
approval. 0081 is the
identifi cation number
of LCIE
The European Commission
mark for Ex products
Equipment grouping: II for surface industry
Equipment category: 2G for gasenvironment demanding a highlevel of protection
II 2 G0081Protection type Ex d = fl ameproof
Equipment grouping IIB for gas group B
Equipment protection level = level b for gasTemperature class T4 = max. permitted 135°C
Ex d IIB T4 GbCE Conformity marking Equipment protection marking for gas:
Protection type Ex d = fl ameproof
Equipment grouping IIB for gas group B
Equipment protection level = level b for gasTemperature class T4 = max. permitted 135°C
Ex d IIB T4 GbExample for gas:
Making of temperatures, gas groups and explosive atmospheres
To ensure equipment can be safely used in potentially explosive atmospheres, the explosive atmospheres where the equipment is installed must be known. The temperature class of equipment must be compared with the spontaneous
ignition the equipment of the gas mixtures concerned, and in specific cases the gas group must be known (e.g.flame proof protection).
Temperature Ignition Max. permitted Gas examples
class temp. of gas/ temp. of
vapour °C equipment °C
T1 >450 450 Hydrogen
T2 >300 <450 300 Ethanol
T3 >200 <300 200 Hydrogen sulfide
T4 >135 <200 135 Diethyl ether
T5 >100 <135 100 -
T6 >85 <100 85 Carbon disulfide
IIA - 120 gases and vapours, e.g. butane/petroleum/propane
IIB - 30 gases and vapours, e.g. ethylene/dimethyl ether/coke oven gas
IIC three gases: hydrogen H2 /acetylene C2H2 carbon disulfide CS2
78 Flameproof motors l ABB drives and motors catalogue 2014
Flameproof motors, 80-400, 2 & 4 poles Ex d/e* IIB T4
TEFC low voltage motors, IP 55, IC 411, single-speed. 400 V 3-phase 50 HzSee product catalogues or www.abb.com/motors&generators for more information on products.
ATEXC e r t i f i e d
HO = High-output design* Efficiency full load 100%
* JP Exd* KP Exde
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
3000 r/min = 2 poles
0.75 M3JP/KP 80 MA 2.5 1.55 80.1 £727 £774
1.1 M3JP/KP 80 MB 3.7 2.2 81.6 £762 £835
1.5 M3JP/KP 90 SLA 4.9 3 81.9 £842 £914
2.2 M3JP/KP 90 SLC 7.3 4.2 84.5 £999 £1,062
3 M3JP/KP 100 LA 9.8 5.5 86.0 £1,058 £1,129
4 M3JP/KP 112 MB 13.1 7.5 86.0 £1,314 £1,401
5.5 M3JP/KP 132 SMB 18 10.1 87.0 £1,527 £1,605
7.5 M3JP/KP 132 SMD 24.5 13.6 88.3 £1,945 £2,009
11 M3JP/KP 160 MLA 35.8 19.7 90.1 £2,250 £2,410
15 M3JP/KP 160 MLB 48.9 26.6 91.2 £2,666 £2,779
18.5 M3JP/KP 160 MLC 60.2 32.3 91.8 £3,033 £3,115
22 M3JP/KP 180 MLA 71.5 38.4 91.7 £3,757 £3,884
22 M3JP/KP 160 MLD 71.7 38.6 91.2 £3,530 £3,644 HO
30 M3JP/KP 200 MLA 96.9 52.7 93.2 £4,782 £4,974
30 M3JP/KP 180 MLB 97.3 52 92.5 £4,476 £4,606 HO
37 M3JP/KP 200 MLC 119 64.1 93.6 £6,354 £6,641
37 M3JP/KP 180 MLC 119 63.9 92.8 £6,266 £6,506 HO
45 M3JP/KP 225 SMB 144 79.5 93.9 £8,596 £8,916
45 M3JP/KP 200 MLE 145 79.1 93.3 £8,099 £8,457 HO
55 M3JP/KP 250 SMA 176 94.5 94.3 £11,306 £11,723
55 M3JP/KP 225 SMC 177 96 93.9 £10,617 £11,018 HO
67 M3JP/225 SMD 215 119 93.9 £12,009 £12,749 HO
75 M3JP/KP 280 SMA 240 130 94.3 £15,329 £15,841
75 M3JP/KP 250 SMB 241 129 94.0 £14,318 £14,815 HO
90 M3JP/KP 280 SMB 288 152 94.6 £20,043 £20,685
90 M3JP/KP 250 SMC 289 153 94.0 £16,018 £17,041 HO
110 M3JP/KP 315 SMA 352 194 94.9 £24,210 £24,690
110 M3JP/KP 280 SMC 352 185 95.1 £22,766 £23,249 HO
132 M3JP/KP 315 SMB 422 227 95.1 £28,699 £29,178
160 M3JP/KP 315 SMC 512 271 95.4 £32,545 £33,025
200 M3JP/KP 315 MLA 640 335 95.7 £40,879 £41,361
250 M3JP/KP 355 SMA 800 423 95.7 £44,530 £45,823
315 M3JP/KP 355 SMB 1009 533 95.7 £54,138 £55,431
355 M3JP/KP 355 SMC 1136 608 95.7 £58,202 £59,494
400 M3JP/KP 355 MLA 1280 677 96.9 £64,482 £65,776
450 M3JP/KP 355 MLB 1440 743 97.1 £72,057 £73,351
500 M3JP/KP 355 LKA 1601 827 96.9 £83,883 £85,176
560 M3JP/KP 400 LA 1789 934 97.2 £115,256 £118,623
560 M3JP/KP 400 LKA 1789 943 97.2 £115,256 £118,623
630 M3JP/KP 400 LB 2014 1048 97.4 £126,000 £130,485
630 M3JP/KP 400 KB 2014 1048 97.4 £126,000 £130,485
710 M3JP/KP 400 LC 2269 1180 97.5 £142,000 £147,000
710 M3JP/KP 400 LKC 2269 1180 97.5 £142,000 £147,000
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1500 r/min = 4 poles
0.55 M3JP/KP 80 MA 3.6 1.41 76.6 £665 £727
0.75 M3JP/KP 80 MB 5 1.77 80.4 £695 £762
1.1 M3JP/KP 90 SLA 7.3 2.4 83.3 £740 £805
1.5 M3JP/KP 90 SLC 10 3.2 83.2 £814 £883
2.2 M3JP/KP 100 LA 14.5 4.3 84.7 £887 £959
3 M3JP/KP 100 LB 19.8 6 86.5 £1,155 £1,224
4 M3JP/KP 112 MC 26.1 8.3 88.2 £1,233 £1,324
5.5 M3JP/KP 132 SMB 36 11.3 88.5 £1,632 £1,723
7.5 M3JP/KP 132 SMD 49 16.1 89.1 £1,815 £1,913
11 M3JP/KP 160 MLC 71.4 21.2 91.2 £2,264 £2,377
15 M3JP/KP 160 MLE 97.6 28 92.0 £2,808 £2,908
18.5 M3JP/KP 180 MLA 119 35.1 91.6 £3,515 £3,659
18.5 M3JP/KP 160 MLF 120 35 91.7 £3,307 £3,403 HO
22 M3JP/KP 180 MLB 142 41.7 91.6 £3,901 £4,044
22 M3JP/KP 160 MLG 143 43.1 90.8 £3,705 £3,836 HO
30 M3JP/KP 200 MLB 194 54.4 93.6 £4,879 £5,056
30 M3JP/KP 180 MLC 194 57.9 92.2 £4,573 £4,701 HO
37 M3JP/KP 225 SMB 238 67.1 93.6 £6,002 £6,226
37 M3JP/KP 200 MLC 239 70 93.0 £5,567 £5,761 HO
45 M3JP/KP 225 SMC 290 78.4 94.1 £7,091 £7,330
55 M3JP/KP 250 SMA 355 100 94.3 £8,694 £9,109
55 M3JP/KP 225 SMD 354 101 94.3 £8,211 £8,611 HO
62 M3JP/KP 225 SME 400 113 93.5 £9,360 £10,282 HO
75 M3JP/KP 280 SMA 482 134 94.5 £11,404 £11,931
75 M3JP/KP 250 SMB 485 133 94.3 £10,729 £11,225 HO
86 M3JP/KP 250 SMC 556 155 94.1 £12,875 £13,470 HO
90 M3JP/KP 280 SMB 579 159 94.7 £15,714 £16,195
110 M3JP/KP 315 SMA 706 194 95.1 £17,959 £18,599
110 M3JP/KP 280 SMC 707 194 95.1 £17,799 £18,279 HO
132 M3JP/KP 315 SMB 847 232 95.4 £21,965 £22,445
160 M3JP/KP 315 SMC 1027 284 95.6 £24,210 £24,690
200 M3JP/KP 315 MLA 1285 351 95.6 £31,904 £32,383
250 M3JP/KP 355 SMA 1604 437 95.9 £39,919 £41,041
315 M3JP/KP 355 SMB 2021 551 95.9 £50,338 £51,459
355 M3JP/KP 355 SMC 2279 621 95.9 £56,749 £57,871
400 M3JP/KP 355 MLA 2565 705 96.3 £63,802 £65,246
450 M3JP/KP 355 MLB 2884 780 96.8 £70,948 £72,241
500 M3JP/KP 355 LKA 3204 865 97.0 £78,524 £79,817
560 M3JP/KP 400 LA 3586 982 96.8 £89,425 £91,086
560 M3JP/KP 400 LKA 3586 982 96.8 £89,425 £91,086
630 M3JP/KP 400 LB 4034 1077 97.0 £100,671 £104,357
630 M3JP/KP 400 LKB 4034 1007 97.0 £100,671 £104,357
710 M3JP/KP 400 LC 4547 1227 97.1 £104,698 £108,531
710 M3JP/KP 400 LKC 4547 1227 97.1 £104,698 £108,531
IE2
Flameproof motors l ABB drives and motors catalogue 2014 79
ATEXC e r t i f i e d
Flameproof motors, 80-450, 6 & 8+ polesEx d/e* IIB T4
TEFC low voltage motors, IP 55, IC 411, single-speed. 400 V 3-phase 50 HzSee product catalogues or www.abb.com/motors&generators for more information on products.
HO = High-output design* Efficiency full load 100%+ IE2 not applicable to 8-pole
* JP Exd* KP Exde
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
1000 r/min = 6 poles
0.37 M3JP/KP 80 MA 3.7 1.14 72.6 £740 £805
0.55 M3JP/KP 80 MB 5.5 1.55 72.9 £774 £837
0.75 M3JP/KP 90 SLA 7.5 2 77.9 £807 £859
1.1 M3JP/KP 90 SLC 11.2 2.8 78.5 £819 £887
1.5 M3JP/KP 100 LA 15 3.6 80.1 £887 £959
2.2 M3JP/KP 112 MB 22.1 5 82.0 £1,233 £1,324
3 M3JP/KP 132 SMB 29.8 6.7 83.3 £1,657 £1,735
4 M3JP/KP 132 SMC 39.6 9.2 84.6 £1,754 £1,815
5.5 M3JP/KP 132 SMD 54.3 12.5 87.6 £1,831 £1,945
7.5 M3JP/KP 160 MLA 74.2 15.3 87.2 £2,264 £2,377
11 M3JP/KP 160 MLB 108 21.7 90.1 £2,985 £3,082
14 M3JP/KP 160 MLC 137 30.2 89.2 £3,583 £3,656 HO
15 M3JP/KP 180 MLB 147 29.2 90.4 £3,980 £4,107
18.5 M3JP/KP 180 MLC 181 40 90.1 £4,497 £4,640 HO
18.5 M3JP/KP 200 MLA 179 35.8 90.9 £4,766 £4,959
22 M3JP/KP 200 MLB 213 42.2 91.6 £5,278 £5,456
30 M3JP/KP 200 MLC 291 59 91.6 £6,658 £6,832 HO
30 M3JP/KP 225 SMB 290 57.2 92.2 £7,074 £7,281
37 M3JP/KP 250 SMA 357 70.8 93.1 £9,078 £9,319
37 M3JP/KP 225 SMC 359 69.8 92.1 £8,052 £8,274 HO
45 M3JP/KP 280 SMA 434 82.7 93.4 £11,404 £11,931
45 M3JP/KP 250 SMB 435 85 93.1 £10,280 £10,520 HO
55 M3JP/KP 280 SMB 530 100 93.8 £15,841 £16,356
75 M3JP/KP 315 SMA 721 139 94.4 £18,118 £18,599
75 M3JP/KP 280 SMC 723 136 94.2 £16,003 £16,356 HO
90 M3JP/KP 315 SMB 866 163 94.8 £21,965 £22,445
110 M3JP/KP 315 SMC 1059 201 95.0 £25,332 £25,972
132 M3JP/KP 315 MLA 1271 240 95.3 £29,019 £29,662
160 M3JP/KP 355 SMA 1538 291 95.4 £35,752 £36,392
200 M3JP/KP 355 SMB 1923 359 95.7 £44,566 £45,368
250 M3JP/KP 355 SMC 2404 454 95.7 £55,466 £56,430
315 M3JP/KP 355 MLB 3032 572 95.7 £69,896 £70,696
355 M3JP/KP 355 LKA 3417 645 95.7 £81,478 £82,772
400 M3JP/KP 400 LA 3846 731 96.2 £88,489 £92,176
400 M3JP/KP 400 LKA 3846 731 96.2 £88,489 £92,176
450 M3JP/KP 400 LB 4323 819 96.6 £99,548 £103,874
450 M3JP/KP 400 LKB 4323 819 96.6 £99,548 £103,874
500 M3JP/KP 400 LC 4808 900 96.6 £110,700 £115,400
500 M3JP/KP 400 LKC 4808 900 96.6 £110,700 £115,400
560 M3JP/KP 400 LD 5385 981 96.9 £117,400 £122,000
560 M3JP/KP 400 LKD 5385 981 96.9 £117,400 £122,000
610 M3JP/KP 450 LA 5860 1098 96.6 Price on request
Output Frame size Torque Current Eff* Foot Flange
kW Nm I price price
750 r/min = 8 poles
0.18 M3JP/KP 80 MA 2.3 0.88 61.0 £741 £805
0.25 M3JP/KP 80 MB 3.3 0.97 63.8 £780 £841
0.37 M3JP/KP 90 SLA 5 1.26 67.0 £799 £867
0.55 M3JP/KP 90 SLC 7.5 1.89 68.7 £878 £948
0.75 M3JP/KP 100 LA 9.9 2.4 75.9 £963 £1,036
1.1 M3JP/KP 100 LB 14.6 3.6 76.4 £1,257 £1,324
1.5 M3JP/KP 112 MC 20 4.7 77.2 £1,328 £1,413
2.2 M3JP/KP 132 SMC 29.1 6 80.1 £1,784 £1,864
3 M3JP/KP 132 SMD 40.3 7.7 79.9 £1,992 £2,054
4 M3JP/KP 160 MLA 52.9 9.3 86.7 £2,153 £2,347
5.5 M3JP/KP 160 MLB 72.6 12.8 86.8 £2,602 £2,697
7.5 M3JP/KP 160 MLC 99.7 18 85.5 £3,098 £3,209
11 M3JP/KP 180 MLB 145 24.9 88.3 £4,030 £4,158
15 M3JP/KP 200 MLA 195 30.4 89.9 £5,166 £5,360
18.5 M3JP/KP 225 SMA 240 40 90.0 £6,177 £6,384
18.5 M3JP/KP 200 MLB 240 37.1 89.8 £5,935 £6,129 HO
22 M3JP/KP 225 SMB 287 45.5 90.6 £7,202 £7,539
30 M3JP/KP 250 SMA 389 60.7 91.4 £9,222 £9,671
30 M3JP/KP 225 SMC 391 61.2 90.7 £8,678 £8,885 HO
37 M3JP/KP 280 SMA 476 73.8 92.7 £11,787 £12,157
37 M3JP/KP 250 SMB 479 74.2 92.2 £10,425 £10,682 HO
45 M3JP/KP 280 SMB 579 89.3 93.2 £15,940 £16,514
55 M3JP/KP 315 SMA 707 104 93.4 £18,118 £18,599
55 M3JP/KP 280 SMC 708 106 93.4 £16,514 £16,838 HO
75 M3JP/KP 315 SMB 966 140 93.7 £22,766 £23,406
90 M3JP/KP 315 SMC 1159 168 94.0 £26,455 £27,095
110 M3JP/KP 315 MLA 1419 203 94.0 £30,782 £31,422
132 M3JP/KP 355 SMA 1694 251 94.7 £35,911 £36,873
160 M3JP/KP 355 SMB 2053 303 95.2 £43,124 £44,246
200 M3JP/KP 355 SMC 2570 378 95.3 £54,024 £54,988
250 M3JP/KP 355 MLB 3213 472 95.4 £73,903 £75,198
315 M3JP/KP 400 LA 4043 584 96.1 £85,123 £88,328
315 M3JP/KP 400 LKA 4043 584 96.1 £85,123 £88,328
355 M3JP/KP 400 LB 4562 641 96.2 £96,023 £99,548
355 M3JP/KP 400 LKB 4562 641 96.2 £96,023 £99,548
400 M3JP/KP 400 LC 5134 731 96.3 £99,507 £103,408
400 M3JP/KP 400 LKC 5134 731 96.3 £99,507 £103,408
430 M3JP/KP 450 LA 5519 789 95.9 Price on request
470 M3JP/KP 450 LB 6032 861 96.0 Price on request
530 M3JP/KP 450 LC 6793 982 96.1 Price on request
600 M3JP/KP 450 LD 7690 1124 96.3 Price on request
IE2
80 Optional extras for low voltage AC motors l ABB drives and motors catalogue 2014
Optional extras for low voltage AC motors
Option Description Modification Motor 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400
Code types £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £
Auxilliary terminal box 418 l N N N N N N N 343 343 343 343 343 343 343 343 343
for accessories 418 n N 343 343 343 343 343 343 343 343 343 343 343 343 343 343 343
418 ▲ N N N N N N N N N 457 457 457 457 457 457 457
British Standard sliderails* l 75 75 75 75 108 108 108 148 148 272 272 456 456 839 839 839
n N 75 75 75 108 108 108 148 148 272 272 456 456 839 839 839
▲ N N 75 75 108 108 108 148 148 272 272 456 456 839 839 839
Degree of Protection IP56* 403 l 232 232 232 232 232 289 289 331 331 331 331 331 331 363 383 441
403 n 232 232 232 232 232 289 289 331 331 331 331 331 331 363 383 441
403 ▲ N N 232 232 232 289 289 331 331 331 331 331 331 363 383 441
Degree of Protection IP65 158 l 232 232 232 232 232 294 294 375 375 375 375 375 330 363 383 441
158 n N 232 232 232 232 294 294 375 375 375 375 375 330 363 383 441
158 ▲ N N 232 232 232 294 294 375 375 375 375 375 R R R R
Exd motor for Gas Group IIC 461 ▲ N N 86 103 134 168 217 341 591 842 1095 1346 1961 3266 6528 9791
External earth bolt* 67 l 66 66 66 66 66 66 66 115 115 115 115 115 112 112 112 112
67 n N 100 100 100 100 100 100 115 115 115 115 115 112 112 112 112
67 ▲ N N S S S S S S S S S S S S S S
Foot and face mounting* 8 l 122 122 122 122 122 159 159 N N N N N N N N N
8 n N 88 88 88 88 128 N N N N N N N N N N
8 ▲ N N 79 79 79 110 140 N N N N N N N N N
Foot and flange mounting* 9 l 122 122 122 122 122 159 159 303 303 402 402 440 379 656 1146 1472
9 n N 88 88 88 88 128 128 268 268 358 358 390 379 656 1146 1472
9 ▲ N N 79 79 79 110 140 268 268 358 358 391 379 656 1146 1472
Frequency converter rating 163 l 67 67 67 67 67 67 67 67 67 67 67 67 67 67 67 67
plate. Rating data according 163 n 67 67 67 67 67 67 67 67 67 67 67 67 67 67 67 67
to quotation 163 ▲ 67 67 67 67 67 67 67 67 67 67 67 67 67 67 67 67
Heating element specify 450/451 l 220 220 220 220 220 246 246 297 329 366 418 502 447 447 500 500
120V or 240V* 450/451 n N 220 220 220 220 246 246 297 329 366 418 502 447 447 500 500
450/451 ▲ N N 220 220 220 246 246 297 329 366 418 502 447 447 500 500
Insulated bearing at NDE. 701 l R R R R R R R R R R R R 1063 1063 1472 1472
Frame 280 and above on 701 n R R R R R R R R R R R R 1063 1063 1472 1472
variable speed drives.* 701 ▲ R R R R R R R R R R R R 1063 1063 1472 1472
Metal fan 68 l 141 141 141 141 141 198 198 285 285 307 322 322 518 555 591 591
68 n N 136 136 136 136 196 196 253 253 270 285 285 518 555 591 591
68 ▲ N N 134 159 159 168 168 253 253 270 285 285 518 555 591 591
Metal fan cover 53 l 94 94 94 94 94 131 129 S S S S S S S S S
53 n N S S S S S S S S S S S S S S S
53 ▲ N N S S S S S S S S S S S S S S
Paint colour to standard RAL 114 l 202 202 202 202 202 198 198 242 242 242 242 242 235 235 235 235
specify RAL no.* 114 n N 202 202 202 202 200 200 242 242 242 242 242 235 235 235 235
114 ▲ N N 202 202 202 200 200 242 242 242 242 242 235 235 235 235
PT100 resistance element 445 l N N N N N 598 598 587 587 869 869 869 819 819 819 819
one per phase 445 n N R R R R 598 598 587 587 869 869 869 819 819 819 819
445 ▲ N N 598 598 598 598 598 587 587 869 869 869 819 819 819 819
PTC thermistors 3 in series, 436 l 123 123 123 123 123 159 159 232 232 232 232 232 200 200 200 200
150°C others on request* 436 n N 123 123 123 123 159 159 232 232 232 232 232 200 200 200 200
436 ▲ N N 123 123 123 159 159 232 232 232 232 232 200 200 200 200
Please note, general performance motors have limited optional extras (see extras marked with*).Select motor from our process performance range when additional extras are required.
R = On requestS = StandardN = Not available
Optional extras for low voltage AC motors l ABB drives and motors catalogue 2014 81
Optional extras for low voltage AC motors
Rain canopy for VI mounting 5 l 104 104 104 104 104 119 119 136 157 165 221 273 329 388 579 579
(mandatory on Ex motors)* 5 n N N 104 104 104 119 119 136 157 165 221 273 329 388 579 579
5 ▲ N N 104 104 104 119 119 136 157 165 221 273 329 388 579 579
Restamping voltage, 2 l 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48
frequency and output, 2 n 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48
continuous duty* 2 ▲ 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48 48
Roller bearing at DE 37 l N N N N N N N 242 278 316 364 402 346 346 506 R
(not available on IIC motors)* 37 n N N N N N N N 242 278 316 364 402 346 346 506 506
37 ▲ N N N N N N N 242 278 316 364 402 346 346 506 506
Separate (Fixed speed) 183 l N 360 360 360 360 874 874 1085 1236 1733 2037 2376 N N N N
motor cooling fan 183 n N R R R 952 1144 1427 1530 1530 1530 1800 2100 2272 2858 3103 3346
183 ▲ N N N N N N N 1951 2086 2822 2822 3123 3544 4129 4375 4620
SPM nipples 43 l N N N N N 146 146 246 276 308 317 317 310 310 310 310
43 n N N N N N N N 246 276 308 317 317 310 310 S S
43 ▲ N N N N N N N 246 276 308 317 317 310 310 S S
Test - routine* 148 l 196 196 196 196 196 222 222 222 222 222 222 222 222 222 222 222
148 n N 196 196 196 196 222 222 222 222 222 222 222 222 222 222 222
148 ▲ N N 196 196 196 222 222 222 222 222 222 222 222 222 222 222
Test - Type test report from 145 l 83 83 83 83 83 83 83 83 83 117 117 117 166 166 166 166
test of an identical motor 145 n N 83 83 83 83 83 83 83 83 117 117 117 166 166 166 166
(where available)*
Alloy l
Cast Iron n
Flameproof ▲
Option Description Modification Motor 63 71 80 90 100 112 132 160 180 200 225 250 280 315 355 400
Code types £ £ £ £ £ £ £ £ £ £ £ £ £ £ £ £
Please note, general performance motors have limited optional extras (see extras marked with*).Select motor from our process performance range when additional extras are required.
R = On requestS = StandardN = Not available
82 High voltage process performance motors l ABB drives and motors catalogue 2014
High voltage process performance motors
ABB has developed a high voltage induction motor that can be offered with a short delivery time. The motor is ideal for the serial OEM who requires a standard product, the electrical and mechanical properties of which do not need to be altered.
The high voltage process performance motor utilises a combination of ABB high voltage motor design expertise and the proven platform of ABB low voltage cast iron motors.The result is a motor with:– a straightforward design– significantly lower price than that of an engineered motor– a standardised ordering process that ensures a short
delivery time– Shaft heights IEC 315 to 450 - 110 kW to 750 kW at 50 Hz - 3 kV to 10 kV– NEMA frames 506AT to 728 - 150 hp to 950 hp (SF 1.15) at 60 Hz - 4 kV (star-connected stator), 2.3 kV (delta-
connected stator)– Rib-cooled cast iron frame (IP55 / IC411 / TEFC)– 2 to 8 poles– Horizontal foot mounted, horizontal foot and flange
mounted and vertical flange mounted– IEC, NEMA, CSA
HV process performance cast iron motors l ABB drives and motors catalogue 2014 83
HV process performance cast iron motors, 315-450, 2 & 4 poles
TEFC high voltage motors, cast iron frame, IP 55, IC411, single-speed, ambient temperature 40°CSee product catalogues or www.abb.com/motors&generators for more information on products.
Output Type Foot-mounted B3
kW Product code Price
3000 r/min = 2 poles 3300V 50Hz
160 M3BM 315 LKA 3GBM 311811-ARA £44,884
200 M3BM 355 LKA 3GBM 351811-ARA £46,094
250 M3BM 355 LKB 3GBM 351821-ARA £48,967
315 M3BM 355 LKC 3GBM 351831-ARA £55,091
335 M3BM 355 LKD 3GBM 351841-ARA £59,575
355 M3BM 400 LA 3GBM 401510-ARA £63,230
400 M3BM 400 LB 3GBM 401520-ARA £67,341
445 M3BM 400 LC 3GBM 401531-ARA £70,992
500 M3BM 400 LKA 3GBM 401810-ARA £74,052
560 M3BM 400 LKB 3GBM 401820-ARA £78,191
Output Type Foot-mounted B3 Vertical V1/B35
kW Product code Price Product code Price
1500 r/min = 4 poles 3300V 50Hz
132 M3BM 315 LKA 3GBM 312810-ARA £42,038 3GBM 312810-BRA £43,298
160 M3BM 315 LKB 3GBM 312820-ARA £42,842 3GBM 312820-BRA £44,102
200 M3BM 315 LKC 3GBM 312831-ARA £44,881 3GBM 312831-BRA £46,142
250 M3BM 355 LKA 3GBM 352810-ARA £48,565 3GBM 352810-BRA £50,177
315 M3BM 355 LKB 3GBM 352820-ARA £52,245 3GBM 352820-BRA £53,856
355 M3BM 355 LKC 3GBM 352830-ARA £54,660 3GBM 352830-BRA £56,276
400 M3BM 355 LKD 3GBM 352841-ARA £57,938 3GBM 352841-BRA £59,550
450 M3BM 400 LA 3GBM 402510-ARA £61,589 3GBM 402510-BRA £63,551
500 M3BM 400 LB 3GBM 402520-ARA £66,102 3GBM 402520-BRA £68,065
560 M3BM 400 LKA 3GBM 402810-ARA £71,412 3GBM 402810-BRA £73,374
630 M3BM 400 LKB 3GBM 402820-ARA £79,021 3GBM 402820-BRA £80,983
630 M3BM 450 LA 3GBM 452510-ARA £79,021 3GBM 452510-BRA £81,170
710 M3BM 450 LB 3GBM 452520-ARA £89,794 3GBM 452520-BRA £91,944
3 kV, 6 kV, 6.6 kV and 10 kV options available on request.
3 kV, 6 kV, 6.6 kV and 10 kV options available on request.
HV process performance cast iron motors, 315-450, 6 & 8 poles
TEFC high voltage motors, cast iron frame, IP 55, IC411, single-speed, ambient temperature 40°CSee product catalogues or www.abb.com/motors&generators for more information on products
Output Type Foot-mounted B3 Vertical V1/B35
kW Product code Price Product code Price
1000 r/min = 6 poles 3300V 50Hz
112 M3BM 315 LKA 3GBM 313811-ARA £47,465 3GBM 313811-BRA £48,726
132 M3BM 315 LKB 3GBM 313820-ARA £48,083 3GBM 313820-BRA £49,343
150 M3BM 315 LKC 3GBM 313831-ARA £48,671 3GBM 313831-BRA £49,931
160 M3BM 355 LKA 3GBM 353810-ARA £49,694 3GBM 353810-BRA £51,305
200 M3BM 355 LKB 3GBM 353820-ARA £52,165 3GBM 353820-BRA £53,776
250 M3BM 355 LKC 3GBM 353830-ARA £56,221 3GBM 353830-BRA £57,833
315 M3BM 400 L 3GBM 403500-ARA £66,424 3GBM 403500-BRA £68,386
355 M3BM 400 LA 3GBM 403510-ARA £68,899 3GBM 403510-BRA £70,861
400 M3BM 400 LB 3GBM 403520-ARA £73,357 3GBM 403520-BRA £75,319
450 M3BM 400 LKA 3GBM 403811-ARA £77,519 3GBM 403811-BRA £79,482
500 M3BM 400 LKB 3GBM 403821-ARA £81,390 3GBM 403821-BRA £83,351
530 M3BM 400 LKC 3GBM 403831-ARA £84,021 3GBM 403831-BRA £85,983
560 M3BM 450 LA 3GBM 453510-ARA £86,652 3GBM 453510-BRA £88,801
630 M3BM 450 LB 3GBM 453520-ARA £92,185 3GBM 453520-BRA £94,333
710 M3BM 450 LC 3GBM 453530-ARA £99,304 3GBM 453530-BRA £101,452
3 kV, 6 kV, 6.6 kV and 10 kV options available on request.
Output Type Foot-mounted B3 Vertical V1/B35
kW Product code Price Product code Price
750 r/min = 8 poles 3300V 50Hz
200 M3BM 400 LA 3GBM 404510-ARA £60,815 3GBM 404510-BRA £62,777
220 M3BM 400 LB 3GBM 404520-ARA £64,466 3GBM 404520-BRA £66,428
250 M3BM 400 LC 3GBM 404530-ARA £68,577 3GBM 404530-BRA £70,539
280 M3BM 400 LD 3GBM 404540-ARA £72,630 3GBM 404540-BRA £74,592
300 M3BM 400 LE 3GBM 404550-ARA £77,519 3GBM 404550-BRA £79,482
315 M3BM 400 LKA 3GBM 404810-ARA £80,286 3GBM 404810-BRA £82,248
355 M3BM 400 LKB 3GBM 404820-ARA £84,182 3GBM 404820-BRA £86,143
375 M3BM 400 LKC 3GBM 404830-ARA £86,546 3GBM 404830-BRA £88,508
400 M3BM 450 LA 3GBM 454510-ARA £89,448 3GBM 454510-BRA £91,596
450 M3BM 450 LB 3GBM 454520-ARA £94,202 3GBM 454520-BRA £96,350
500 M3BM 450 LC 3GBM 454530-ARA £98,471 3GBM 454530-BRA £100,619
530 M3BM 450 LD 3GBM 454540-ARA £101,131 3GBM 454540-BRA £103,279
3 kV, 6 kV, 6.6 kV and 10 kV options available on request.
84 High voltage process performance motors l ABB drives and motors catalogue 2014
Optional extras for high voltage motors
Note: certain variant codes cannot be used togetherPlease see product catalogues for more variants.
R = On requestS = Standard
Code Variant 315 355 400 450
Price Price Price Price
Bearings and lubrication
107 RTD Pt-100 in each bearing, 3-wire £593 £593 £593 £593
037 Roller bearing at D-end, inc. 036 Transport lock (not available for 2-pole) £1,185 £1,426 £1,426 £1,481
SPM nipple (for shock pulse measuring) in each bearing S S S S
654 Provision for vibration sensors (M8 x 1 thread) £1,477 £1,477 £1,477 £1,477
Coupling
035 Assembly of customer supplied coupling-half £2,902 £2,902 £2,902 £2,902
Heating elements
450 Heating element 100-120V - 1ph £483 £483 £483 £483
451 Heating element 200-240V - 1ph £483 £483 £483 £483
Packing / Seaworthy packing
Seaworthy packing £4,298 £4,298 £4,298 £4,298
Painting
114 Special paint colour, customer specified RAL grade £1,261 £1,261 £1,261 £1,261
Protection
005 Metal protective roof (rain canopy), vertical motor, shaft down £2,175 £2,175 £2,175 £2,175
158 Degree of protection IP65 £644 £644 £644 £644
403 Degree of protection IP56 £644 £644 £644 £644
Rating & instruction plates
002 Restamping output and voltage, continuous duty £161 £161 £161 £161
Stator winding temperature sensors
RTD Pt-100 (6 pcs) inside stator slots, 3-wire S S S S
Terminal box
447 Top mounted separate auxiliary terminal box for heating elements £932 £932 £932 £932
750 Star point terminal box (not available for V1) £1,908 £1,908 £1,908 £1,908
Testing
Routine test report S S S S
146 Type test with report for motor from specific delivery batch £8,300 £8,300 £8,300 £8,300
147 Type test with report for motor from specific delivery batch, customer witnessed £9,751 £9,751 £9,751 £9,751
762 Noise level test £2,957 £2,957 £2,957 £2,957
Foundation and installation
Slide rails (2 pcs) for belt drives £2,632 £2,632 £2,632 £2,632
Optional extras for high voltage motors l ABB drives and motors catalogue 2014 85
NEMA motors
ApplicationsPumps, compressors, fans, conveyors, machine tools and other general purpose three-phase applications.
FeaturesSuitable for mounting in any position. Ball bearings, heavy-gauge steel and cast-iron frames, and gasketed conduit boxes. Class F insulation, 1.15 service factor, low-loss electrical grade lamination steel. EM Super-E® motors have NEMA Premium® efficiency and three years warranty. Motors with TR suffix have roller bearings for heavy belted loads.
ApplicationsPetrochemical plants, mines, foundries, pulp and paper plants, waste management facilities, chemical plants, tropical climates and other processing industry applications requiring protection against corrosion caused by severe environmental operating conditions.
FeaturesECP motors are XEX designs. 1.15 service factor, corrosion resistant epoxy finish, regreasable ball or roller bearings, oversized rotatable cast iron conduit box, cast iron frames, V-ring shaft seal, moisture resistant copper windings. Class F insulation, stainless steel nameplate and corrosion resistant hardware. ECP/XEX Super-E® motors have NEMA Premium® efficiency and three years warranty. Positive lubrication system (PLS) on 360 frames and larger.
ApplicationsIdeal for use where hazardous fumes or dust may be present.
FeaturesUL and CSA approved for Division 1, Class I, Group D; Class I, Group D, Class II Group F & G; Class I, Group C & D, Class II, Group F & G. Corrosion resistant epoxy finish. Shipped with U.L. and CSA approved cast conduit box assembled to each motor. 1.00 service factor. EM Super-E® explosion proof motors have NEMA Premium® efficiency and three years warranty.
General purpose industrial motorsThree phase, totally enclosed, foot mounted– 1/8 – 400 hp– NEMA 42 – 449T
Severe duty motorsThree phase, totally enclosed, foot mounted – 1 – 400 hp– NEMA 143T – 449T
86 NEMA low voltage AC motors l ABB drives and motors catalogue 2014
Explosion proof motorsSingle and three phase, foot mounted– 1/4 – 300 hp– NEMA 48 – 449T
– All reducers can be shaft mounted: screw conveyor, vertical, and flange mounted
– Kilowatt ratings through 294 kW – Torque ratings through 56,500 Nm – Standard 5, 9, 15, 25, and up to 40:1 gear ratios– Nearly 300:1 speed reduction with V-belt drives – Twin-tapered bushing bores: 25 mm through 160 mm – Highly efficient helical gearing – Meets or exceeds AGMA standards, including 5,000 hours
L10 life and 25,000 average hour life – New heavy duty lip seals for extended wear life,
-40 to 138°C – 100 percent factory noise and leak tested – New metal shield sealing system with excluder lip – AGMA output torque ratings up to 56,500 Nm
– Inline helical (ILH), right angle helical bevel (RHB), motorised shaft mount (MSM)
– Output ratings 0.75 kW to 56 kW; up to torque 14,000 Nm– Ratios, 1.5:1 - 300:1 – 8 case sizes per housing configuration, clamp collar,
3-piece coupled, integral gearmotor, separate input. Solid, straight hollow output – ILH/MSM efficiency of 98 percent per stage, RHB efficiency of 95 percent per stage
– All units shipped filled with oil from the factory and are installation ready
– Optional XT harsh duty seal for operation in wet and dirty environments
– Class 30 gray iron housings cast with internal ribbing for added strength
– Options include washdown and screw conveyor configurations
– Parallel shaft or right angle configurations available – Torque capacities from 32 to 104 kNm available– Global product design to fit all markets– Multiple mounting configurations available (base mounting,
swing base mounting, tunnel housings)– Can be used with a variety of soft start mechanisms
including VSD and fluid couplings
Torque-Arm II
Quantis
MagnaGearXTR®
Gearings l ABB drives and motors catalogue 2014 87
Gearings
For well over a century, Dodge products have helped manufacturers, OEMs, and producers increase the productivity and profitability of their operations.ABB is excited to bring the history and innovation of Dodge mechanical power transmission products to our portfolio.
ABB’s commitment includes adding new warehouse space to stock Dodge MPT products, which ensures they are quicklyaccessible when you need them. Experts in the products and industries we serve will also be added to promote the products and serve our customers.
– Superior 65° locking setscrew – DualGuard seal – comprised of single lip seal and
rubberised flinger– Stronger, more flexible bearing cage – Optimum balance between locking forces – Heat stabilised nylon construction with and inner ring stress
fiber-glass reinforcement– Secure fit to the shaft
Mounted ball bearings When it comes to reliable service and low maintenance, ABB Dodge® mounted ball bearings are unmatched in the industry. ABB Dodge mounted ball bearings are available in any of our proven locking devices: our exclusive 65° setscrew locking
– Two types: normal duty GT and medium duty GTM – DualGuard seal – comprised of single lip seal and
rubberised flinger – Thin wall adapter mounting offers 360° full shaft contact
and concentricity. No shaft – Marring or fretting corrosion like setscrew and eccentric
collar products. Integral dismount feature easily removes the bearing from the shaft. Turned, ground, and polished shafting is not required
– Anti-rotation device prevents insert rotation associated with heavy loads, vibration, unbalanced loads, and high-speed applications
– High-temperature option available to 204 °C– Plus or minus 2° static misalignment
88 Mounted Bearings l ABB drives and motors catalogue 2014
Mounted bearings
– Reinforced polymer and stainless steel housings – Patented polymer housing includes antimicrobial agent
which resists bacterial and fungus growth - two inserts: corrosion resistant and stainless steel insert
– Three locking devices: 65° setscrew angle (SC), Grip Tight adapter mount and concentric clamp collar (D-Lok).
– Quadguard seal: comprised of our triple lip seal and rubberised flinger. Additional grease retention provided by the maxlife cage
– Anti-rotation device prevents insert rotation associated with heavy loads, vibration, unbalanced loads, and high-speed applications - plus or minus 2° static misalignment
Ultra Kleen®, E-Z Kleen®
system, our patented Grip Tight adapter mounted, eccentric locking collars and D-Lok™ concentric clamp locking system mounted ball bearing.
Grip Tight® ball bearings
Setscrew ball Bearings
Roller bearingsFor decades, industry’s leading producers have depended on ABB Dodge® roller bearings to handle their conveyance and power transmission needs. Dodge bearings offer
– Industry’s only push/pull adapter mount system – Available in two-bolt pillow blocks– Accepts commercial shaft tolerances– Installation and removal in fewer than 15 minutes– Fully concentric shaft attachment with adaptor
sleeve mount – Virtually eliminates fretting corrosion – Capable of withstanding static or dynamic misalignment
of ±1° - shaft-ready out of the box - available with Trident triple lip or labyrinth seal options
– Sizes range from 30 mm through 170 mm – SN mounting dimensions
– Tapered rolling elements – Completely assembled, factory adjusted, and
properly lubricated – Shaft ready – Extra protection – E-Tect seal option - comparable mounting dimensions with
ball bearings – E-xtra allows easy upgrade from ball bearings
ISN spherical roller bearings
Type E-xtra® tapered roller bearings
Mounted Bearings l ABB drives and motors catalogue 2014 89
Mounted bearings
innovative designs; a wide range of shaft attachment methods, rolling elements, housings, and seal choices, patented features and consistent performance.
Elastomeric, sleeve style - Dodge D-Flex couplings
Three-way flexing action handles shock, vibration, and misalignment. The ABB Dodge D-Flex™ coupling features moulded, non-lubricated, interchangeable elastomeric sleeves of EPDM, neoprene, or Hytrel. Its three-way flexing action accommodates torsional, angular, and parallel misalignment, as well as axial end float.
Elastomeric, tyre style - Dodge Para-Flex Superior design provides advantages over other rubber or polyurethane elements.
ABB Dodge Para-Flex elements are manufactured with reinforcing fabric tension cords that transmit much of the torque during operation.
The uniform and centred bead in the foot of the tyre element prevents it from pulling out during operation. Additionally, the tyre element is reinforced at the split to reduce fatigue and extend life.
Industry leading misalignment capabilities.
ABB Dodge Para-Flex elements provide accommodation of shaft misalignment during installation, running-time and replacement better than other elastomeric elements.
With an industry-leading combined 4° angular, 3.17 mm (1/8 in.) parallel, and 7.93 mm (5/16 in.) end-float capability, Para-Flex couplings will perform in difficult applications and reduce valuable time needed for installation and maintenance.
90 Couplings l ABB drives and motors catalogue 2014
Couplings
Metallic, grid style - Dodge Grid-Lign Compact in size, yet high in torque capability. ABB Dodge Grid-Lign couplings are available in a variety of sizes, in standard and spacer styles. Every coupling features two steel shaft hubs, a tapered grid element, two seals and a cover assembly. Its versatile design allows for a motor or reducer output speed connection, and its speed capability ranges up to 6,000 rpm dependant on size. ABB Dodge Grid-Lign is also available in both T31 and T35 spacer designs up to size 1200T. This spacer offering can be used as a spacer coupling, or mounted to a brake disc or drum.
Flexible tapered element - The ABB Dodge Grid-Lign coupling’s tapered grid element is engineered with high-strength, spring steel that is quenched and tempered. This feature helps isolate vibration and cushions shock loads. In addition, it allows uniform contact during light, normal and shock-loading conditions for long machine life.
High torque capability - Torque capabilities on the ABB Dodge Grid-Lign coupling range up to 800,000 Nm (7 million lb-in) dependant on size. Whether it is overland conveyors or underground mines, the high torque ratings allow for customers to specify a Grid-Lign coupling in the largest conveyor applications.
Couplings
Couplings l ABB drives and motors catalogue 2014 91
A quick guide to supply voltages and frequencies worldwide
Country Frequency Industrial Voltage
Hz in common use (V)
AFRICA
Algeria 50 415/230, 380/220
Angola 50 380/220
Botswana 50 400/230
Burkina Faso 50 380/220
Burundi 50 380/220
Cameron 50 380/220
Central African Rep 50 380/220
Chad 50 380/220
Congo Rep. 50 380/220
Congo Dem. Rep. 50 380/220
Egypt 50 380/220
Ethiopia 50 380/220
Gambia 50 400/230
Ghana 50 415/240, 400/230
Guinea 50 440/220, 380/220
Guinea-Bissau 50 220/110
Ivory Coast 50 380/220
Kenya 50 415/240, 380/220
Lesotho 50 380/220
Libya 50 400/230
Malawi 50 400/230, 380/220
Morocco 50 400/230, 380/220
Mozambique 50 380/220
Namibia 50 220
Nigeria 50 415/240, 380/220
Rwanda 50 400/230
Senegal 50 400/230
Sierra Leone 50 400/230
South Africa* 50 500, 400/230, 380/220
Sudan 50 400/230
Tanzania 50 400/230
Tunisia 50 400/230
Uganda 50 415/240
Zaire 50 415, 380/220
Zambia 50 400/230
Zimbabwe 50 400/230
Country Frequency Industrial Voltage
Hz in common use (V)
MIDDLE EAST
Bahrain 50 400/230, 380/220
Iraq 50 400/230
Israel 50 415, 400/230, 280/220
Jordan 50 400/230, 380/220
Kuwait 50 415/240
Lebanon 50 380/220
Oman 50 415/240
Qatar 50 415/240
Saudi Arabia 50, 60 440/220, 400/230, 380/220
Syria 50 380/220
United Arab Emirates 50 415/220
ASIA
Afghanistan 50 380/220
Armenia 50 380/220
Azerbaijan 50 380/220
Bangladesh 50 380/220
Bhutan 50 400/230
Cambodia 50 380/220
China* 50 380/220
Hong Kong 50 380/220
India* 50 415/240, 400/230
Indonesia 50 380/220
Iran 50 400/230, 380/220
Japan 50, 60 440/220, 400/200
Kazakhstan 50 380/220
Korea North 60 380/220
Korea South 60 440, 380/220
Laos 50 380/220
Malaysia 50 415/240
Myanmar (Burma) 50 400/230
Nepal 50 400/230
Pakistan 50 415/240, 400/230
Philippines 60 440, 220/110
Singapore 50 415/240
Sri Lanka 50 400/230, 380/220
Taiwan R.O.C. 60 440, 380/220
Thailand 50 380/220
Vietnam 50 380/220
92 Quick guide to supply voltages worldwide l ABB drives and motors catalogue 2014
Quick guide to supply voltages worldwide l ABB drives and motors catalogue 2014 93
A quick guide to supply voltages and frequencies worldwide
Country Frequency Industrial Voltage
Hz in common use (V)
OCEANIA
Australia 50 415/240
Fiji 50 415/240
New Zealand 50 415/240, 400/230
NORTH AMERICA
Canada 60 600, 575, 460/230
USA 60 460/230
CENTRAL & SOUTH AMERICA
Antigua 60 480, 460, 440, 230,
230/460, 220
Argentina 50 660, 380, 220
Aruba 60 480, 460, 440, 230,
230/460, 220
Bahamas 60 480, 460, 440, 230,
230/460, 220
Barbados 50 480, 460, 440, 230,
230/460, 220
Belize 60 480, 440, 240, 220
Bermuda 60 480, 460, 440, 230,
230/460, 220
Bolivia 50 480, 440, 220/380
Brazil 60 690, 480, 460, 440, 380/660,
220/380/440, 280/380
Chile 50 690, 575, 460,
380/660, 380/220
Colombia 60 230/480, 230/460, 220/440,
110/220
Costa Rica 60 480, 440, 240, 220
Cuba 60 480, 460, 440, 230,
230/460, 220
Ecuador 60 660, 480, 460, 220/440
El Salvador 60 480, 440, 240, 220
Guatemala 60 480, 440, 240, 220
Guyana 60 480, 460, 440, 230,
230/460, 220
Haiti 60 480, 460, 440, 230,
230/460, 220
Honduras 60 480, 440, 240, 220
Jamaica 60 480, 460, 440, 230, 230/460, 220
Mexico 60 440/220
Nicaragua 60 480, 440, 240, 220
Panama 60 480, 440, 240, 220
Paraguay 50 660, 380, 220
Peru 60 690, 480, 460, 440, 380,
220, 220/440
Uruguay 50 500, 380/690, 220/380
Venezuela 60 480, 460, 440, 230, 230/460, 220
Country Frequency Industrial Voltage
Hz in common use (V)
EUROPE
Andora 50 400/230, 380/220
Austria 50 690, 400/230
Belarus 50 380/220
Belgium 50 400/230
Bosnia-Herzegovina 50 380/220
Bulgaria 50 380/220
Cyprus 50 415/240, 400/230
Croatia 50 400/230, 380/220
Czech Rep 50 690, 400/230, 380/220
Denmark 50 400/230
Estonia* 50 380/220
Finland* 50 690, 500, 400/230
France 50 400/230, 380/220
Germany 50 690, 400/230
Greece 50 400/230, 380/220
Hungary 50 400/230, 380/220
Iceland 50 400/230, 380/220
Ireland 50 400/230, 380/220
Italy* 50 400/230, 380/220
Latvia 50 380/220
Liechtenstein 50 400/230
Lithuania 50 380/220
Luxembourg 50 400/230, 380/220
Macedonia 50 220
Malta 50 415/240
Monaco 50 400/230, 380/220
Montenegro 50 400-690
Netherlands 50 500, 400/230
Norway 50 690, 500, 400/230
Poland 50 400/230, 380/220
Portugal 50 400/230, 380/220
Romania 50 400/230, 380/220
Russia* 50 380/220
Serbia 50 380
Slovakia 50 400/230, 380/220
Slovenia 50 400/230, 380/220
Spain* 50 400/230, 380/220
Sweden* 50 690, 500, 400/230
Switzerland 50 690, 500, 400/230
Turkey 50 230/400
Ukraine 50 380/220
United Kingdom 50 690, 415/240, 400/230, 380/220
*Manufacturing sites
Useful engineering information
Reference information and explanation of abbreviations
Degrees of protectionAs defined by IEC 34-5 and BS 4999 pt 105, the code generally consists of ‘IP’ followed by two digits: the first describing the protection against solid bodies or protection to persons against contact with live or moving parts inside the enclosure; the second describing the protection against ingress of water.
Cooling formsAs defined by IEC 34-6 and BS 4999 pt.106, the code generally consists of ‘IC’ followed by two digits; the first describing the cooling circuit arrangement; the second describing the method of supplying power to circulate the coolant. Where more than one cooling circuit is in use, these may be expressed as ‘IC’ followed by groups of two digits, e.g. IC0141.
The following forms are used in this catalogue:IC410 – Typical examples are roller table motorsIC411 – Standard motorsIC416 – Standard motors (normally bigger frame sizes only
equipped with auxilliary fan)IC418 – Fan application motors without a cooling fan,
cooled by the air stream of the driven machineIC01 – Open drip-proof motorsIC31W – Water cooled motors
Mounting formsThe arrangements are defined by IEC 34-7, BS 4999 pt. 107 code II (and DIN 42950). The following forms are used in this catalogue and are for motors with two bearings housed in end-shields. When flange mounting they have access to the back of the flange.
IM1001 (B3) Horizontal foot mountedIM1011 (V5) Vertical foot mountedIM3001 (B5) Horizontal flange mountedIM3011 (V1) Vertical flange mounted
IM2001 (B35) Horizontal foot & flange mountedIM1071 (B8) Horizontal foot, ceiling mounted
Note for gearbox users – service factorThe geared motors covered by this catalogue are rated for driven machines with a uniform load for continuous duty or occasional moderate shock loading on single-shift operation, being known as a Unity Service Factor. For applications with short-time duty, high inertia or heavy shock loads, advice should be sought on calculating the correct service factor and selecting the most suitable gearbox type.
AbbreviationsElectrical dataKilowatt = kWVolts = VArmature Volts = VaField Volts = VfAmperes = AArmature Current = laField Current = IfPower factor = PF
Useful conversion factors1hp = 746W1Nm = 8.851 lb.in1mm = 0.03937inch 1m2 = 10.765ft2
1kg.m2 = 1Nms2 = 0.73752 lb.ft2
Useful formulae1 Watt = 1 Nm/s
Torque (lb ft) = 5250 x hp speed (rpm)
Torque (Nm) = 9550 x kW speed (rpm)
3 phase = 1.732 x V x I x PFAC power (kW) 1000
1 phase = V x I x PFAC power (kW) 1000
First Meaning Second Meaning
Digit (Protection Against) Digit (Protection Against)
0 Not protected 0 Not protected
1 50mm dia. body 1 Vertical drips
2 12mm dia. body 2 Drips up to 15° from vertical
3 2.5mm dia. body 3 Drips up to 60° from vertical
4 1mm dia. body 4 Splashing from any direction
5 Dust protected 5 Water jets from any direction
6 Dust tight 6 Heavy seas (Does not cover
corrosion resistance, etc)
7 Effects of immersion
NOTE: IP66 does not imply outdoor use, it is merely a statement of ingress protection against water and dust, outdoor mounting has to combat the effects of heat, humidity and direct sunlight.
94 Choosing the right drive for your application l ABB drives and motors catalogue 2014
Useful engineering information l ABB drives and motors catalogue 2014 95
Choosing the right drive for your application
Please do not hesitate to call ABB if you require assistance selecting your drive and motor
Process
Identify the applicationIdentify the type of application and the likely demands of the drive
Gather the load data: system inertia, required acceleration and deceleration rates, minimum and maximum speeds, overload requirements, etc.This information can often be determined by the performance of the existing motor
Gather the motor data: rated torque, kW, volts insulation class, speed, etc.Whether an existing motor or a new motor is being used, the motor information is critical to choosing a drive
Choose a driveMatch the data gathered in steps 1 to 3 against the table of drive features in the feature finder page xx. Select a drive that meets the motor requirements and has all the software features needed for the application
Is the drive offered in the correct kW/amp rating?The drive you choose must be able to supply the necessary current to the motor to produce the torque required. This includes normal and overload conditions. Select current from the tables within this catalogue
Is the drive offered in the correct enclosure and environmental ratings?The drive you choose must be available in an enclosure style that will withstand the application’s environment. It also must produce the required current at the application’s altitude and ambient temperature
Does this drive have the features needed to meet the application’s demands?The drive you choose must have a feature set that matches the application. It also must have sufficient hardware (inputs and outputs, feedback, communications etc.) to perform the application
Does this drive have the motor control performance to meet the application’s demands?The drive you choose must be able to produce the needed torque at the necessary speeds. It must also be able to control speed and torque depending on the application requirements
Does the drive have the right user interface?The drive you choose must interface with the customer correctly, do you need a simple keypad, no keypad or a full text assistant keypad?
Does the drive have the right level of safety?The drive you choose could be responsible for the safety in your system after changes in the machinery directive, some ABB drives contain built in safety functionality
Congratulations!The ABB AC drive you have chosen has the features and performance needed for a successful application
Action
Continue to step 2.
Continue to step 3.
Continue to step 4.
Continue to step 5.
If yes, continue to step 6.If no, go to step 4.
If yes, continue to step 7.If no, go to step 4.
If yes, continue to step 8.If no, go to step 4.
If yes, continue to step 9.If no, go to step 4.
If yes, continue to step 10.If no, go to step 4.
If yes, continue to step 11.If no, go to step 4.
or
or
or
or
or
or
Step
1
2
3
4
5
6
7
8
9
10
11
Contact us
Driv
es &
Mot
ors
cata
logu
e 20
14 v
1/Fe
b 20
14ABB LimitedDaresbury ParkDaresburyWarringtonCheshireWA4 4BTTel: +44 (0) 1925 741 111Fax: +44 (0) 1925 741 212
www.abb.co.uk/energy
Notes: We reserve the right to make technical changes or modify the contents of this document without prior notice. With regard to purchase orders, the agreed particulars shall prevail. ABB does not accept any responsibility whatsoever for potential errors or possible lack of information in this document.
We reserve all rights in this document and in the subject matter and illustrations contained therein. Any reproduction, disclosure to third parties or utilization of its contents – in whole or in parts – is forbidden without prior written consent of ABB.
Copyright© 2014 ABB
All rights reserved
Printed in UK (02.2014)