Duplicator BPS-125 Parts Manual

transcript

I. Shell Unit

VR-231B、VR-231、VC-21S

No. Product Name Inventory Code Drawing No. Qty. Remark

① Scanning cover part 2.03.06.448 1 VR-231，Details as per I.1

① Scanning cover part 2.03.06.449 1 VR-231B、VC-21S，Details

as per I.1

2 Plate making set screw 3.03.02.089 RD-T07-043 2

3 Plate making fixed

eccentric sleeve

3.03.03.095 RD-T07-043-02 1

4 Top cover of plate

making

3.06.01.091 RD-T07-041 1

5 Rear cover shell of 3.06.01.076 RD-T07-014 1

all-in-one machine

6 Rear cover shell

blanking plate 2

3.06.01.094 RD-T07-048AB 1

⑦ Feed paper holding

board part

2.03.06.107 1 Details as per I.2

8 Plastic wrench of paper

feeding board

3.06.01.009 RD-T02-035 1

9 Pressure wrench cover 3.06.01.080 RD-T07-018 1

10 Front cover shell 3.06.01.607 RD-T14-050 1

11 Door bolt 3.03.01.217 RD-T14-053 1

12 Door connector 2.02.00.017-08 RD-T14-054 2

13 Switchboard of front

2.01.01.212 RD-T12-111 1

14 Trademark box 3.06.01.609 RD-T14-055 1

15 Front door cover 3.06.01.608 RD-T14-051 1

16 Suction seat of paper

delivery holding board

3.06.01.036 RD-T03-080AB 1

17 Magnetic steel 3.10.003 RD-T03-079AB 1

18 Suction block of paper

holding board

2.01.01.091 RD-T03-078AB 2

19 Iron absorption board 2.01.01.621 RD-T14-052 1

(20) B4 paper delivery board

(21) Control panel

component (Chinese)

3.03.03.054 RD-T07-043-01 1

I. Shell Unit

VR-230、VR-230B、VC-20S

1 Top cover of main

control panel

3.06.01.601 RD-T14-003 1

2 Plate making set screw 3.03.02.089 RD-T07-043 2

eccentric sleeve

3.03.03.095 RD-T07-043-02 1

4 Plate making top cover 3.06.01.091 RD-T07-041 1

5 Rear cover shell of

all-in-one machine

3.06.01.076 RD-T07-014 1

6 Rear cover shell

blanking plate 2

3.06.01.094 RD-T07-048AB 1

7 Paper feed holding 2.03.06.107 1 Details as per I.2

board part

8 Plastic wrench of paper

feeding board

3.06.01.009 RD-T02-035 1

9 Pressure wrench cover 3.06.01.080 RD-T07-018 1

10 Front cover shell 3.06.01.607 RD-T14-050 1

11 Door bolt 3.03.01.217 RD-T14-053 1

12 Door connector 2.02.00.017-08 RD-T14-054 2

13 Switchboard of front

2.01.01.212 RD-T12-111 1

14 Trademark box 3.06.01.609 RD-T14-055 1

15 Front door cover 3.06.01.608 RD-T14-051 1

16 Suction seat of paper

delivery holding board

3.06.01.036 RD-T03-080AB 1

17 Magnetic steel 3.10.003 RD-T03-079AB 1

18 Suction block of paper

holding board

2.01.01.091 RD-T03-078AB 2

19 Iron absorption board 2.01.01.621 RD-T14-052 1

(20) B4 paper delivery board

(21) Control panel

component (Chinese)

3.03.03.054 RD-T07-043-01 1

23 Fixed pillar of main

control panel top cover

3.03.02.312 RD-T14-004 4

I.1 Scanning Cover Part

VR-231

① Scanning cover part 2.03.06.448 1 VR-231

1 Lower cover of A3

scanning feed board

3.06.01.129 RD-T10-050 1

2 Left label of original

paper scanning

specification

3.07.02.240 RD-T14-083 1

3 Left paper splint of

original paper

3.06.01.133 RD-T10-052 1

4 A3 scanning cover 3.06.01.137 RD-T10-055 1

5 Toothed plate of

original pressing board

3.06.01.135 RD-T10-053 2

6 Lining plate of A3

scanning cover

3.06.02.007 RD-T10-046 1

7 Gasket 3.05.04.023 4 φ3*φ8*1

8 Second paper feed

upper shaft bushing

2.01.01.057 RD-T02-129AB 1 φ4*φ16*1

9 Traveling gear of

pressing board

3.06.01.136 RD-T10-054 1

10 Gear shell 3.06.01.138 RD-T10-056 1

11 Right paper splint of

original paper

3.06.01.131 RD-T10-051 1

12 Right label of original

paper scanning

specification

3.07.02.242 RD-T14-085 1

13 Upper cover of A3

original paper scanning

3.06.01.127 RD-T10-049 1

I.1 Scanning Cover Part

VR-231B、VC-21S

① Scanning cover part 2.03.06.449 1 VR-231B、VC-21S

1 Upper cover of A3

scanning feed board

3.06.01.127 RD-T10-049 1

2 Left label of original

paper scanning

specification

3.07.02.239 RD-T14-082 1

3 Left paper splint of

original paper

3.06.01.133 RD-T10-052 1

4 A3 scanning cover 3.06.01.137 RD-T10-055 1

5 Toothed plate of

original pressing board

3.06.01.135 RD-T10-053 2

6 Lining plate of A3

scanning cover

3.06.02.007 RD-T10-046 1

7 Gasket 3.05.04.023 4 φ3*φ8*1

8 Second paper feed

upper shaft bushing

2.01.01.057 RD-T02-129AB 1 φ4*φ16*1

9 Traveling gear of

pressing board

3.06.01.136 RD-T10-054 1

10 Gear shell 3.06.01.138 RD-T10-056 1

11 Right paper splint of

original paper

3.06.01.131 RD-T10-051 1

12 Right label of original

paper scanning

specification

3.07.02.241 RD-T14-084 1

13 Lower cover of A3

original paper scanning

3.06.01.129 RD-T10-050 1

I.2 Paper Feed Holding Board Part

⑦ Paper feed holding

board part

2.03.06.107 1

1 Paper holding board

2.01.02.101-01 RD-T07-003 1

2 Paper feed board 2.01.01.145 RD-T07-002 2

3 Paper feed holding

3.06.01.065 RD-T07-001 1

4 Paper feed suction

2.01.01.146 RD-T07-005 1

5 Paper feed turn-over

3.06.01.067 RD-T07-004 1

I.3 B4 Paper Holding Board Part

(20) B4 paper holding board

2.03.06.387 1

1 Left baffle of paper

holding table

3.06.01.604 RD-T14-027 1

2 Front baffle of paper

holding table

3.06.01.603 RD-T14-026 1

3 Gasket 3.05.04.023 3 φ3*φ8*1

4 Paper feed suction

2.01.01.146 RD-T07-005 1

5 Paper model label (left) 3.07.02.233 RD-T14-029 1

6 Right baffle of paper

holding table

3.06.01.605 RD-T14-028 1

7 Paper model label

(right)

3.07.02.234 RD-T14-030 1

8 U-baseboard of Paper

holding table

3.06.01.602 RD-T14-025 1

9 Fixed paper delivery

splint part

2.03.04.004 RD-T03-004 3

10 Vertical label of paper

3.07.02.235 RD-T14-031 1

I.4 Control Panel Part (Chinese)

(21) Control panel part

(Chinese)

2.03.06.680 1

1 Touch panel (Chinese) 3.06.01.612 RD-T14-063 1

2 Wire from touch key to

control panel

3.02.05.280 2 0.5*24*150*B

3 USB interface blanking

3.06.01.616 1 Without drawing number

at the moment

4 Control panel 3.06.01.611 RD-T14-061 1

5 Touch panel (large) 3.02.37.018 1 KQ-Touch2-120501

6 Control panel 3.02.37.016 1

7 Fixed leg of control

3.06.01.614 RD-T14-061-01 5

8 Located leg of control

3.06.01.615 RD-T14-061-02 5

9 Touch panel (small) 3.02.37.017 1 KQ-Touch1-120501

II．Frame Unit

1 Front wall board of AIO

machine

2.01.02.464-01 RD-T14-001 1

2 Rear wall board of AIO

machine

2.01.02.465-01 RD-T14-002 1

3 Supporting structure of

plate making machine

(upper)

2.01.01.175 RD-T09-065 2

4 Supporting structure of

(lower)

2.01.01.176 RD-T09-066 2

5 Rear cover shell of

2.01.02.121-01 RD-T09-061(B) 1

6 Power socket 2.01.01.001 RD-T01-009 1

7 Power socket (AC) 3.02.04.030 RD-T22-058AB 1 PST-101S

8 Front baseboard baffle 2.01.02.012-01 RD-T02-006 1

9 Stopblock of machine

lifting handle

2.01.02.005-03 RD-T01-006AB 4

10 Machine lifting handle 2.01.02.003-01 RD-T01-005 4

11 Paper parallelizing

board bracket

2.01.01.052 RD-T02-100AB 6

12 Front and rear footing 3.06.03.001 RD-T01-007 4

13 Spot welding parts of

front and rear footing

2.03.03.001-01 RD-T01-003-01 2

14 AC switch (power

switch)

3.02.02.002 RD-T21-012AB 1 R220-22C-11A

15 Power switch 2.01.01.002 RD-T01-011 1

16 Cover board of rear

footing (spray)

2.01.02.006-01 RD-T01-008 1

17 Supporting board of

control panel

2.01.01.592 RD-T13-134 1

II．Frame Unit

18 Draft style main

control panel shell

2.01.01.601 RD-T14-005 1

19 Locating structure of

main control wiring

2.01.02.453-01 RD-T13-015AB 2

20 Draft style scanning

installation structure

2.01.01.602 RD-T14-006 2

21 Main control panel 3.02.37.015 1 VR-231B/VR-231/VC-21S

21 Main control panel 3.02.37.019 1 VR-230B/VR-230/VC-20S

22 Main control 2.01.01.582 RD-T13-005 1

installation board

23 Bracket of main

control installation

2.01.01.504 RD-T13-006AB 2

24 Draft style scanning

side blanking plate

2.01.01.603 RD-T14-007 1

25 Small bracket of draft

style scanning cover

2.01.01.604 RD-T14-008 2

26 Main board

installation bracket

2.01.01.583 RD-T13-007 1

(27) B4 left track guide part 2.03.06.007 1 Details as per II.1

28 Riveted part of drum

2.03.01.003 RD-T01-017-01AB 1

29 Driver board (B) guard

2.05.00.002 RD-T01-059AB 1

30 Stationary shaft of

circuit board 2

3.03.02.014 RD-T01-038-01AB 4

31 Secondary power

3.02.34.001 RD-T22-011AB 1 CWT－0908116A

32 Primary power board 3.02.34.006 1 KOA-250M3 (without

33 Stationary shaft of

circuit board

3.03.02.013 RD-T01-038AB 4

34 Main motor driver

board guard strip

2.05.00.001 RD-T01-058AB 1 Addition

(35) # 3 switch base part 2.03.06.002 1 Details as per II.2

(36) B4 right track guide

2.03.06.006 1 Details as per II.3

37 Drum limiting plate 2.01.01.012 RD-T01-026 1

II. Frame Unit

38 Rear locating pillar

(drum)

3.03.02.005 RD-T01-027AB 2

39 Flange nut 3.05.02.053 4

40 Wire fixing frame

(short)

2.01.02.250-01 RD-T01-056 1

41 Wire fixing frame

(short)

2.01.02.252-01 RD-A3-T01-031 1

42 Frame of paper delivery

support

2.01.01.611 RD-T14-024 2 M6

43 Stationary frame of

waste box

2.01.01.615 RD-T14-034 2

44 Drum socket box 2.01.01.011 RD-T01-025AB 1

45 Inching switch part 2.03.06.001 2

46 Drum socket base

riveted part

2.03.01.143 1

47 Fixed leg of the front

frame of roller

3.03.02.004 RD-T01-024 2

II．Frame Unit

(48) B4 draft scanning part 2.03.06.612

1 VR-231B 、 VC-21S ，

details as per X

(48) A4 draft scanning part 2.03.06.613 1 VR-231，details as per X

49 Draft scanning side

board cover

2.01.01.603 RD-T14-007

1 VR-231 、 VR-231B 、

VC-21S

(50) Wastebasket part 2.03.06.559 1 Details as per VII

(51) Roller part 2.03.06.525

1 VR-231B、VR-230B、

VC-21S 、 VC-20S ，

Details as per VI

(51) Roller part 2.03.06.527 1 VR-231 、 VR-230 ，

Details as per VI

(52) Plate making machine

part 2.03.06.604

1 VR-231B、VR-230B、

VC-21S 、 VC-20S ，

Details as per IX

(52) Plate making machine

part 2.03.06.605

1 VR-231 、 VR-230 ，

Details as per IX

53 Wax paper cylinder

3.06.01.572 RD-T13-215AB 2

54 Thermal head cover 3.06.01.120 RD-T09-062AB 1

55 Cover 2.01.02.122 RD-T09-063 1

56 Wax paper baffle 2.01.02.123 RD-T09-064-01 1

(57) Cutting part 2.03.06.573 1 Details as per VIII

II.1 B4 Left Guide Rail Part

(27) B4 left track guide part 2.03.06.007 1

1 Left track guide riveted

2.03.01.002 RD-T01-013-03 1

2 Drum track roller 3.06.01.002 RD-T01-016AB 1

II.2 #3 Switch Base Part

(35) #3 switch base part 2.03.06.002 1

1 Microswitch (front

door, roller)

3.02.02.004 RD-T21-014AB 1

2 #3 switch board tension

spring

3.03.04.001 RD-T01-022 1

3 Locating sleeve 3.04.001 RD-T01-023 1

4 #3 switch workboard 2.01.01.010 RD-T01-021 1

5 #3 switch base riveted

2.03.01.004 RD-T01-020-01 1

II.3 B4 Right Track Guide Part

(36) B4 right track guide

2.03.06.006 1

1 Drum track roller 3.06.01.002 RD-T01-016AB 1

2 Right track guide

riveted part

2.03.01.001 RD-T01-013-01 1

III．Paper Feed Unit

1 Paper feed workboard 2.01.01.033-03 RD-T02-033 1

② Vertical support part 2.03.06.098

1 VR-231 、 VR-231B 、

VC-21S details as per

3 # 1 sensor seat 2.03.06.090 1 VR-231 、 VR-231B 、

VC-21S

4 # 2 & 6 sensor seats 2.03.06.088 1 VR-231 、 VR-231B 、

VC-21S

5 Riveted part of

knockout plate

2.03.01.020 RD-T02-121-01 1

⑥ Part B of # 1 switch

2.03.06.120 1 Details as per III.2

7 Fixed leg of second

paper feed knockout

3.03.02.034 RD-T02-115 1

8 Second paper feed

toothed plate tension

spring

3.03.04.012 RD-T02-113AB 1

9 Second paper feed

toothed plate (tension

spring board)

2.01.01.056 RD-T02-114AB 2

(10) Second paper feed

toothed plate part

11 Aluminum tooth plate

support shaft

3.03.02.033 RD-T02-111 1

(12) Paper feed workboard

(13) Small paper wheel part

of second paper feed

2.03.06.087 RD-T02-159AB 1 Details as per III.5

14 6201Z bearing 3.05.05.002 1

(15) First paper feed toothed

plate part

16 First paper feed toothed

plate pillar

3.03.02.026 RD-T02-068AB 1

III. Paper Feed Unit

17 Paper feed board

switch bearing

3.03.03.012 RD-T02-042 1

18 Tension spring of paper

feed board

3.03.04.007 RD-T02-043 1

19 Paper feed board

switch

2.01.01.040 RD-T02-044 1

20 Locating sleeve 3.04.005 RD-T02-045 2

21 Fixed leg of paper feed

board spanner

3.03.02.021 RD-T02-038 1

22 Riveted part of paper

feed board spanner

2.03.01.013 RD-T02-036-01 1

23 #1 switch pressure

2.01.01.034 RD-T02-034 1

24 Eccentric bushing of

Second paper feed

connector

3.03.03.024 RD-T02-140AB 1

(25) First paper feed switch

base part

2.03.06.085 RD-T02-051-07AB 1 Details as per III.7

26 Feed cam 3.06.01.019 RD-T02-107 1

27 Second paper feed

bearing baffle

2.01.01.061 RD-T02-152AB 2

28 Long axis baffle of air

2.01.01.053 RD-T02-103AB 2

29 6001Z bearing 3.05.05.001 2

30 Oil bearing axle seat 3.04.048 RD-T09-017AB 2

31 Tension spring base 2.01.01.030 RD-T02-026AB 2

32 First paper feed toothed

plate tension spring

3.03.04.010 RD-T02-070AB 1

33 Riveted part of second

paper feed rocker arm

2.03.01.023 RD-T02-141-01AB 1

34 Connecting board

(paper feed)

2.01.01.058 RD-T02-138 1

35 Eccentric bushing of

second paper

connecting board

3.03.03.024 RD-T02-140AB 2

36 Paper feed switch

bearing seat

2.01.02.039-03 RD-T02-126AB 1

37 Tension spring of

second paper

workboard

3.03.04.014 RD-T02-136 1

38 Oil bearing shaft 3.04.006 RD-T02-050AB 1

39 Locating pillar of

second paper feed

rocker arm

3.03.02.037 RD-T02-144AB 1

40 Long tension spring of

paper feed workboard

3.03.04.004 RD-T02-025 1

41 Tension spring of paper

feed workboard

3.03.04.003 RD-T02-024 1

42 Spring pressure board 2.01.02.024 RD-T02-032 1

43 Paper feed pressure

workboard

2.01.01.029 RD-T02-023 1

44 Steel ball 3.05.03.001 RD-T02-029AB 1 Sφ4

45 Riveted part of

adjusting cover

2.03.01.012 RD-T02-030-02AB 1

(46) Pressure adjusting

board part

47 Front baseboard baffle 2.01.02.012-01 RD-T02-006 1

upper shaft part

(49) Air pump long shaft

drilling part

(50) Panel part 2.03.06.109 1 Details as per III.11

rubber roller

3.03.01.009 RD-T02-150 1

52 Weld assembly of

paper poking switch

square shaft

2.03.02.021 RD-T02-122-01 1

(53) B4 rubber roller long

shaft part 2.03.06.110 RD-T02-046 1

VR-231B 、 VR-231 、

VR-230B 、 VR-230 ，

details as per III.12

(53) B4 rubber roller long

shaft part 2.03.06.128 RD-T02-046 1

VC-21S、VC-20S，details

as per III.12

(54) Paper separating base

2.03.06.086 RD-T02-097-03AB 1 details as per III.13

(55) Paper parallelizing

board part

2.03.06.093 1 details as per III..14

(56) Door stopper part of 2.03.06.021 1 details as per III.15

paper feed board

57 Riveted part of left

fixed plate of square

2.03.01.011-04 RD-T02-021-01 1

(58) Paper forward board

2.03.06.092 1 details as per III.16

59 Square shaft of paper

forward board

3.03.01.002 RD-T02-019 1

60 Riveted part of right

fixed plate of square

2.03.01.010-04 RD-T02-020-01 1

61 Paper parallelizing

bearing shaft

3.03.02.031 RD-T02-101AB 2

III.1 Vertical Frame Part

VR-231、VR-231B、VC-21S

② Vertical frame part 2.03.06.098 1

1 Vertical position 3.06.01.014 RD-T02-080AB 1

sensing board

2 Worm gear 3.03.05.001 RD-T02-079AB 1

3 Vertical motor part 2.03.05.025 RD-T21-007AB 1

4 Vertical fixing board 2.01.02.029-03 RD-T02-072-01AB 1

5 Vertical frame 2.01.01.043 RD-T02-072 1

Riveted part of vertical

position adjusting

2.03.01.018 RD-T02-074-01 1

7 Mobile bushing 3.03.03.017 RD-T02-087AB 1

8 Eccentric shaft 3.03.03.018 RD-T02-088AB 1

9 Riveted part of driving

2.03.01.019 RD-T02-082-01 1

10 Vertical frame worm

locating sleeve 3.04.010 RD-T02-075AB 1

11 Worm 3.03.05.002 RD-T02-083AB 1

III.2 #1 Switch Base Part B

⑥ #1 switch base part B 2.03.06.120 1

1 #1 switch base B 2.01.01.004 RD-T01-012-01 1

XV-15 microswitch

100g (paper locking,

lifting)

3.02.02.007 RD-T21-017AB 1 XV-152-1C25(100g)

3 Red fiber gasket 3.05.04.001 2 φ3*φ8*1.2

III.3 Second Paper Feed Toothed Plate Part

toothed plate part

2.03.06.089 1

1 Second paper feed

toothed plate part

2.03.04.002 RD-T02-109AB 1

2 Connecting board 2.01.01.055 RD-T02-112AB 1

3 Fixing shaft of

connecting board

3.03.03.019 RD-T02-109-02AB 1

4 Fixing pillar of

connecting board

3.03.02.032 RD-T02-109-01AB 1

5 Fixing pillar of second

paper feed board

3.03.02.034 RD-T02-115 1

6 Gasket 3.05.04.030 1 φ6*φ12*1

7 Hex nut 3.05.02.004 1 M5

III.4 Paper Feed Workboard Part

(12) Paper feed workboard

2.03.06.097 1

1 Paper feed workboard 2.01.01.054 RD-T02-108 1

2 698ZZ bearing 3.05.05.010 1

III.5 Small Paper Wheel Part of Second Paper Feed Unit

(13) Small paper wheel part

2.03.06.087 RD-T02-159AB 1

1 RC040708 unilateral

bearing

3.05.05.012 1

2 Small paper wheel of

second paper feed unit

3.04.016 RD-T02-156AB 1

3 Second paper feed

small paper wheel

insert

3.04.017 RD-T02-158AB 1

III.6 First Paper Feed Toothed Board Part

(15) First paper feed toothed

board part

2.03.06.091 1

1 626Z bearing 3.05.05.003 1

2 Bearing fixing pillar 3.03.02.027 RD-T02-069AB 1

3 Riveted part of first

paper feed toothed

2.03.01.016-03 1

4 Light spring gasket 3.05.04.205 1 5mm

5 Hex nut 3.05.02.004 1 M5

6 First paper feed toothed 3.04.009 RD-T02-067AB 1

plate copper bush

III.7 First Paper Feed Switch Base Part

(25) First paper feed switch

base part

2.03.06.085 RD-T02-051-07AB 1

1 Connecting sleeve 3.03.03.014 RD-T02-057AB 1

2 Short shaft of first

paper feed unit

3.03.02.025 RD-T02-058AB 1

3 Oil bearing seat 3.04.006 RD-T02-050AB 1

4 Short shaft of first

paper feed unit

3.03.03.015 RD-T02-058-01AB 1

5 Ratchet wheel 3.06.01.012 RD-T02-059AB 1

6 Non-return spring 3.03.04.009 RD-T02-060AB 1

7 Gasket 3.05.04.024 1 φ4*φ8*0.6

8 Paper feed pinion 3.04.007 RD-T02-061AB 1

9 Oil bearing seat 3.04.008 RD-T02-062AB 1

10 First paper feed switch 2.01.01.042 RD-T02-051AB 1

11 Riveted part of ratchet

2.03.01.014 RD-T02-052-01AB 1

12 Electromagnet A 3.02.03.001 RD-T21-019AB 1

13 Middle standing shaft 3.03.02.024 RD-T02-054AB 1

14 Flat gasket 2.01.01.016 RD-T01-034AB 1 φ6.5*φ13*1

15 Liner 2.01.02.026 RD-T02-063AB 1 φ6.1*φ13*0.2

16 Ratchet tension spring 3.03.04.008 RD-T02-055AB 1

III.8 Pressure Adjusting Board Part

(46) Pressure adjusting

board part

2.03.06.111 1

1 Pressure adjusting

2.01.01.031 RD-T02-027 1

board buttons

3.06.01.008 RD-T02-028AB 1

III.9 Second Paper Feed Upper Shaft Part

upper shaft part

1 One-way tension spring

upper shaft

3.03.04.015 RD-T02-147AB 2

2 Second paper feed

upper shaft

3.03.01.008 RD-T02-146 1

3 Weld assembly of

second paper feed

workboard

2.03.02.022-03 RD-T02-135-01 1

4 Rivet sleeve of second

paper feed shaft frame 3.03.03.022 RD-T02-132AB 2

Riveted with "8" second

paper feed frame for

delivery

Second paper feed

upper shaft tension

spring gasket B

3.03.03.027 RD-T02-148-02AB 1

6 Oil bearing 3.04.015 RD-T02-149AB 2

7 Second paper feed

upper shaft flat gasket

2.01.01.057 RD-T02-129AB 2 φ4*φ16*1

8 Second paper feed

frame 2.01.01.060 RD-T02-148AB

2 Riveted with "4" second

paper feed rivet sleeve for

delivery

9 Hex nut 3.05.02.002 2 M3

main shaft pin

3.03.02.036 RD-T02-131AB 1

main shaft

3.03.01.007 RD-T02-130 1

balancing shaft

3.03.01.006 RD-T02-127 1

Second paper feed

upper shaft tension

spring gasket A

3.03.03.026 RD-T02-148-01AB 1

III.10 Long Shaft Drilling Part of Air Pump

(49) Long shaft drilling part

of air pump

2.03.06.175 1

1 Paper feed plastic cam

shaft base

3.03.06.002 RD-T02-106AB 1

2 Long shaft of air pump 3.03.01.004 RD-T02-102 1

3 Weld assembly of air

pump toothed base

2.03.02.020-06 RD-T02-105-01 1

III.11 Panel

(50) Panel 2.03.06.109 1 See III..11

1 Panel 2.01.02.031-01 RD-T02-091 1

2 Panel plastic sheath 3.06.01.015 RD-T02-092 2

III.12 B4 Pickup long axis

VR-231B、VR-231、VR-230B、VR-230

(53) B4 Pickup long axis 2.03.06.110 RD-T02-046 1

1 Pickup auxiliary roller 2.03.06.084 RD-T02-049-01AB 2

2 Pickup roller 3.06.03.003 RD-T02-048AB 1 Rongda

3 Pickup long axis 3.03.01.003 RD-T02-047-01 1

III.12 B4 Pickup long axis

VC-21S、VC-20S

(53) B4 Pickup long axis 2.03.06.128 RD-T02-046 1

1 Pickup auxiliary roller 2.03.06.084 RD-T02-049-01AB 2

2 Pickup roller 3.06.03.037 RD-T02-048AB 1 Jiawen

3 Pickup long axis 3.03.01.003 RD-T02-047-01 1

III.13 Paper parting base

(54) Paper parting base 2.03.06.086 RD-T02-097-03AB 1

1 Footstock block rubber 3.06.03.006 RD-T02-097-02AB 1

2 Paper parting base 3.06.01.018 RD-T02-097-01AB 1

3 Hexagon nut 3.05.02.002 1 M3

III.14 Homogeneous board

(55) Homogeneous board 2.03.06.093 1 See III.14

1 Paper block 3.06.01.016 RD-T02-095 2

2 Homogeneous board

spot welding

component

2.03.03.005 RD-T02-093-01 1

3 rotating shaft for

adjustment

2.04.02.002-04 RD-T02-164AB 1

4 Manual adjusting

sheath

3.06.01.021 RD-T02-172AB 1

5 Primary paper feeding

pressure adjusting label

3.07.02.001 RD-T02-171AB 1 Chinese

6 Primary paper feeding

small hanging board

2.01.01.067 RD-T02-170AB 1

7 Paper parting base

2.01.01.062 RD-T02-161AB 1

8 Homogeneous board

spring

3.03.04.011 RD-T02-099AB 1

Pressure adjusting and

positioning roller

spring

2.01.02.043 RD-T02-166AB 1

10 Adjusting and

positioning roller

2.01.01.065 RD-T02-165AB 1

11 Pressure adjusting and

positioning roller

cushion

2.01.02.042-03 RD-T02-167AB 1 φ6.2*φ13*0.8

12 Adjusting cam 2.01.01.066 RD-T02-168AB 1

frame positioning pillar

3.03.02.040 RD-T02-169AB 1

14 Paper feeding pressure

adjusting frame 2.01.01.063 RD-T02-162AB 1

2.01.01.064 RD-T02-163AB 1

16 Paper parting base

supporting board

2.01.01.335 RD-T02-160AB 1

17 Hexagon nut 3.05.02.002 2 M3

18 Paper block 3.06.01.017 RD-T02-095-01 2

III.15 Paper feeding board door stopper

(56) Paper feeding board

door stopper

2.03.06.021 1

1 Door stopper 3.06.01.003 RD-T01-043 1

2 Paper feeding board

door stopper

2.01.01.017 RD-T01-042 1

III.16 Front paper feeding

(58) Front paper feeding 2.03.06.092 1

1 Gasket 3.05.04.023 8 φ3*φ8*1

2 Paper clamp spring 3.03.04.002 RD-T02-009-05 8

3 Paper clamp s locking

and riveting component

2.03.01.008-04 RD-T02-009-08 2

4 Paper clamp right 2.01.02.018-04 RD-T02-009-06 1

movement block

5 Paper clamp movement

3.06.01.005 RD-T02-011 2

6 Paper clamp right

riveting component

2.03.01.007-01 RD-T02-009-07 1

7 Rubber and plastic

paper clamp

2.05.00.003 RD-T02-009-10 2

8 Paper clamp flat

gasket

2.05.00.004 RD-T02-013 2

9 Front paper feeding

board rubber cushion

3.06.03.002 RD-T02-012AB 1

10 Paper clamp left

riveting component

2.03.01.009-01 RD-T02-009-11 1

11 Paper clamp left

movement part

2.01.02.016-04 RD-T02-009-01 1

12 ront paper feeding

board point welding

component

2.03.03.004-01 RD-T02-008-01 1

13 Cushion 2.01.01.026 RD-T02-014-01 2 φ4.1*φ10*1

14 hexagon nut 3.05.02.003 2 M4

15 Paper clamp plastic

3.06.01.006 RD-T02-014 2

16 hexagon nut 3.05.02.002 2 M3

17 No-paper switch base 2.01.01.027 RD-T02-015AB 1

18 No-paper switch base

gasket

2.01.02.020-03 RD-T02-015-01AB 1

19 Microswitch (no paper) 3.02.02.003 RD-T21-013AB 1 K3L

20 Front paper feeding

board switch cover

3.03.03.007 RD-T02-018AB 1

21 No paper switch panel 3.06.01.007 RD-T02-017AB 1

22 Switch fixing panel 2.01.01.028 RD-T02-016-01AB 1

IV．Paper outlet

① Disengaging pawl 2.03.06.161 RD-T03-037-02 1 See iv.1

② B4 square shaft 2.03.06.167 1 See IV.2

3 Disengaging pawl

spring base

2.01.02.269-03 RD-T03-027 1

4 Disengaging pawl

working plate spring

3.03.04.017 RD-T03-026 1

5 Positioning sheath 3.04.005 RD-T02-045AB 2

⑥ Air pump 2.03.06.165 1 See IV.3

⑦ Main engine tightening

plate component 2.03.06.030

1 See IV.4

STPD/STS-S4.5450

paper outlet

synchronous belt

3.06.03.012 RD-T04-011 1 S4.5M-450-6

9 Oily axle seat 3.04.048 RD-T09-017AB 2

10 Paper outlet plastic

roller (synchronous) 3.06.01.024 RD-T03-015 1

11 Electromotor sensor 3.06.01.025 RD-T03-016AB 1

12 Limiting plate 2.01.01.080 RD-T03-028 1

13 Main engine roller

riveting component

2.03.01.026 RD-T03-021-01 1

(14) Paper outlet fixing

component

2.03.06.189 1 See IV.5

(15) Printing pull adjusting

panel 2.03.06.247

1 See IV.6

16 Paper outlet idler

pulley long axis

3.03.01.010 RD-T03-009 1

17 Paper outlet idler

pulley 3.06.03.007 RD-T03-010 1

18 ZYT76-5 permanent

magnet DC motor 3.02.01.002 RD-T21-002 1 ZYT76-5

IV.1 Disengaging pawl

① Disengaging pawl 2.03.06.161 RD-T03-037-02 1

1 Paper outlet roller axis 3.03.02.042 RD-T03-034 1

2 Paper outlet roller 2.03.04.006 RD-T03-031 1

3 Supporting shaft 2.01.01.082 RD-T03-030 1

4 Disengaging pawl

component

2.03.04.007 RD-T03-037 1

5 Point welding

component of paper

outlet roller

2.03.03.007 RD-T03-029-01 1

6 Air pump base 3.06.01.031 RD-T03-038 1

7 Paper outlet part base

3.03.02.041 RD-T03-033 1

8 Paper outlet roller

wspring

3.03.04.018 RD-T03-035 1

IV.2 B4 Square shaft

② B4 square shaft

component

2.03.06.167 1

1 square shaft 3.03.01.011 RD-T03-023 1

2 Disengaging pawl

workding panel

2.01.01.075 RD-T03-024 1

3 Disengaging pawl

axis base

2.01.01.076 RD-T03-025 1

IV.3 Air pump component

⑥ Air pump component 2.03.06.165 1

1 Air pump working arm 2.01.01.086 RD-T03-049AB 1

2 Elastic cylindrical pin 3.05.07.009 1 3*25

3 Gasket 3.05.04.023 2 φ3*φ8*1

4 Air pump piston 3.06.01.033 RD-T03-043 1

5 O-shape sealing gasket

(air pump)

3.06.03.010 RD-T03-044 1

6 Register pin 3.05.08.004 RD-T03-048AB 1 2*6

7 Plastic sheet 2.05.00.005 RD-T03-045AB 1

8 Air pump plunger 2.05.00.013 RD-T03-046AB 1

9 Air pump cylinder 3.06.01.032 RD-T03-040 1

10 Air pump base 2.01.01.085 RD-T03-039 1

IV.4 Main engine synchronous belt tightening panel component

Main engine

synchronous belt

tightening panel

2.03.06.030

1 Gasket 2.01.01.016 RD-T01-034AB 1

2 626Z bearing 3.05.05.003 1

450 Riveting

component of Main

engine synchronous

belt tightening panel

component

2.03.01.005 RD-T01-033-01 1

IV. Paper outlet fixing base component

(14) Paper outlet fixing base

component

2.03.06.189 1

Sensor receiving plate

of paper jam in the

right of (finished

product)

2.03.05.016 RD-T22-006AB 1

2 Paper outlet base

sensor

2.01.01.610 RD-T14-022 1

3 Hex nut 3.05.02.002 2 M3

4 Paper outlet fixing base 2.01.02.461-01 RD-T14-023 1

5 Right label of Paper

outlet fixing base

3.07.02.004 RD-T03-001-02 1

6 Right paper outlet

2.01.02.047-01 RD-T03-003(A) 1

7 Paper outlet fixing

2.01.02.050-01 RD-T03-007 1

8 Paper outlet static

3.09.001 RD-T03-003-03 2

9 static brush supporting 2.01.01.069 RD-T03-003-02 1

10 Paper outlet fixing

sheath

3.03.03.029 RD-T03-003-01 2

11 Left paper outlet clamp 2.01.02.048-01 RD-T03-003(B) 1

12 Left label of Paper

outlet fixing base

3.07.02.003 RD-T03-001-01 1

13 Fixed paper outlet

clamp component

2.03.04.004 RD-T03-004 2

IV .6 Printing roller pressure adjusting panel component

Printing roller pressure

adjusting panel

component

2.03.06.247

1 Printing roller pressure

adjusting panel 2.01.01.208

RD-T12-050 1

2 Pull adjusting sheath 3.03.03.004 RD-T01-067 1

panel button 3.06.01.008

RD-T02-028AB 1

V．Printing

1 NO. 3, 5 sensor base 2.03.06.242 2

② Loading and unloading

frame component

2.03.06.241 1 See V.1

③ Frame base component 2.03.06.245 1 See V.2

4 Fixing sheath of gear at

limiting wheel

3.03.03.091 RD-T04-004-01 1

5 Flange nut 3.05.02.053 2 M6

⑥ Plastic cam component 2.03.06.244 1 See V.3

⑦ Rotary drum gear base

component

2.03.06.251 1 See V.4

8 NO. 4 sensor base 2.03.06.243 1

9 NO. 2, 6 sensor base 2.03.06.088 1

10 Riveting component of

No. 6 sensor plate 2.03.01.029 RD-T04-017-01 1

11 Fixing pillar of Rotary

drum gear base 3.03.02.048 RD-T04-001-01 1

12 Gasket in up axis of

secondary paper 2.01.01.057 RD-T02-129AB 1

feeding

13 Frame of limiting gear

in Rotary drum 2.01.01.355 RD-T04-004-02 1

14 Limiting gear pillar 3.03.02.049 RD-T04-006 2

Limiting gear

component in Rotary

2.03.04.010 RD-T04-004AB 2

16 Plastic cam(air pump

cam) 3.06.01.041 RD-T04-018 1

17 Fixing plate of limiting

gear 2.01.01.098 RD-T04-003AB 1

18 Eccentric sheath of

working panel 3.03.03.040 RD-T04-049AB 1

19 NO. 7 sensor base 2.03.06.252 1

20 Printing shaft liner 3.04.030 RD-T04-057AB 2

21 Bush 3.03.03.042 RD-T04-058 1

22 Disengaging pawl

rocker 2.01.01.622 RD-T14-021 1 change

Moving sheath of

Disengaging pawl

rocker

3.03.03.041 RD-T04-052 1

Eccentric sheath of

connecting panel of

secondary paper

feeding

3.03.03.024 RD-T02-140AB 1

Gear panel of

secondary paper inlet

(spring plate)

2.01.01.056 RD-T02-114AB 1

26 Right spring of printing

board 3.03.04.061 RD-T12-070 1

Riveting component of

working plate of

printing roller

2.03.01.032 RD-T04-046-01 1

28 Drive gear shaft 3.03.02.051 RD-T04-014AB 1

29 Plastic synchronous

belt component 2.03.04.011 RD-T04-009AB 1

30 Fixing sheath of drive

gear axis 3.03.03.035 RD-T04-015AB 1

31 626Z bearing 3.05.05.003 2

31 Printing roller 3.03.01.015 RD-T04-069AB 1 VR-231B 、 VR-230B 、

VC-21S、VC-20S

32 Printing roller 3.03.01.016 RD-T04-069-01 1 VR-230、VR-231

(33) Printing shaft 2.03.06.253 1 See V.5

component

V.1 loading and unloading frame component

③ Loading and unloading

frame component

2.03.06.241 1

1 Head hanging motor

component (lifting)

2.03.05.020 RD-T21-008AB 1

2 No.5 sensor panel 2.01.01.106 RD-T04-029AB 1

3 Loading and unloading

frame base

2.01.01.104 RD-T04-027 1

4 Copper sheath of

loading and unloading

frame base

3.04.028 RD-T04-027-01AB 1

5 No. 5 plastic wheel 3.06.01.042 RD-T04-031AB 1

6 Motor gear 3.04.029 RD-T04-034AB 1

7 No. 5 sensor shaft 3.03.02.054 RD-T04-030 1

8 sensor shaft base 2.01.01.107 RD-T04-032 2

9 rear head hanging

switch panel

2.01.01.108 RD-T04-033AB 2

belt tightening plate

2.03.01.031 RD-T04-042-01 1

11 Aluminum tightening

wheel component

2.03.04.013 RD-T04-044AB 1

12 No.3 sensor panel 2.01.01.109 RD-T04-036AB 1

13 STPD/STS-S4.5 284

synchronous belt 3.06.03.013 RD-T04-038AB 1 S4.5M-284-6

14 Plastic wheel of

synchronous belt (head

hanging)

3.06.01.043 RD-T04-037AB 1

15 No.3 sensor shaft 3.03.02.055 RD-T04-039 1

V.2 Frame base component

④ Frame base component 2.03.06.245 1

1 taper bolt 3.05.07.031 1 4*25

Riveting component of

position base in rotary

2.03.01.030 RD-T04-026-01 1

3 Bearing base 2.06.00.005 RD-T04-002AB 1

4 6801Zbearing 3.05.05.009 1

5 Frame base 2.01.01.103 RD-T04-022 1

V.3 Plastic cam component

⑥ Plastic cam component 2.03.06.244 1

1 Plastic cam(air pump

3.06.01.041 RD-T04-018 1

2 No. 4 sensor panel 2.01.01.101 RD-T04-020 1

V.4 Rotary drum gear base component

⑦ Rotary drum gear base

component

2.03.06.251 1

1 Rotary drum gear base 2.01.01.097 RD-T04-001 1

2 Gear positioning

panel(drive cam) 2.01.01.099 RD-T04-008AB 1

3 Bearing base 3.04.024 RD-T04-002AB 1

4 6900Z bearing 3.05.05.008 1

V.5 printing shaft component

(33) Printing shaft

component 2.03.06.253 1

Welding component of

printing surface

adjusting panel

2.03.02.023-06 RD-T04-048-01AB 1

Gasket of up shaft at

secondary paper

feeding

2.01.01.057 RD-T02-129AB 2 φ4*φ16*1

3 Welding component of

printing shaft 2.03.02.024 RD-T04-056-01 1

pressure adjusting 2.03.02.025-03 RD-T04-069-01AB 1

5 Gasket 3.05.04.033 2 φ4*φ12*0.8

6 Right spring 3.03.04.020 RD-T04-067AB 1

7 Fixing sheath of

tightening plate 3.03.03.044 RD-T04-066AB 2

8 Left tightening plate 2.01.01.115 RD-T04-062AB 1

right block 2.03.02.027-03 RD-T04-072 1

10 Balance shaft 3.03.01.014 RD-T04-068AB 1

left block 2.03.02.026-03 RD-T04-071 1

12 Right tightening plate 2.01.01.116 RD-T04-064AB 1

13 Left spring 3.03.04.021 RD-T04-067-01AB 1

VI．Roller

VR-231B、VR-230B、VC-21S、VC-20S

① B4 head hanging cover

component

2.03.06.324 1 See VI.1

② Roller shell component 2.03.06.328 1 See VI.2

③ Roller (II) core

component 2.03.06.311 1

See VI.3

④ Roller front frame

component

2.03.06.326 1 See VI 六.4

⑤ Ink box component 2.03.06.312 1 See VI.5

⑥ Roller (I) core

component

2.03.06.329 1 See VI.6

⑦ Roller right track

component

2.03.06.335 1 See VI.7

⑧ Roller left track 2.03.06.334 1 See VI.8

component

⑨ Roller steel net

component

2.03.06.336 1 See VI.9

positioning plate

2.03.02.028-03 RD-T05-042-01 1

11 Taper bolt 3.05.07.031 1 4*25

VI．Roller

VR-231、VR-230

① B4 head hanging cover

component

2.03.06.324 1 See VI.1

② Roller shell component 2.03.06.328 1 See VI.2

③ Roller (II) core

component 2.03.06.311 1

See VI.3

④ Roller front frame

component

2.03.06.326 1 See VI 六.4

⑤ Ink box component 2.03.06.312 1 See VI.5

⑥ Roller (I) core

component

2.03.06.329 1 See VI.6

⑦ Roller right track

component

2.03.06.335 1 See VI.7

⑧ Roller left track

component

2.03.06.334 1 See VI.8

⑨ Roller steel net

component

2.03.06.336 1 See VI.9

positioning plate

2.03.02.028-03 RD-T05-042-01 1

11 Taper bolt 3.05.07.031 1 4*25

VI.1 B4 Head hanging cover component

① B4 Head hanging cover

component

2.03.06.324 1

left shaft in Head

hanging cove

2.03.02.029-04 RD-T05-053-01 1

2 Head hanging 2.01.01.388 RD-T05-049 1

cover(B4)

3 Paper clamp bar (B4) 3.06.03.014 RD-T05-050 1

4 Right shaft of Head

hanging cover

3.03.02.069 RD-T05-055AB 1

5 Lfet spring of Head

hanging cover

3.03.04.027 RD-T05-056-01AB 1

VI.2 Roller shell component

② Roller shell component 2.03.06.328 1

1 Gauze lower frame 2.01.02.086-04 RD-T05-059 1

2 Right spring of head

hanging cover

3.03.04.026 RD-T05-056AB 1

4 Head hanging base 2.01.01.392 RD-T05-048 1

5 Right platen of head

hanging

3.06.01.049 RD-T05-057AB 1

6 Iron shaft platen of

gauze(right)

2.01.02.091-04 RD-T05-062 1

7 Gauze upper frame 2.01.02.088-04 RD-T05-060 1

8 Gauze assembly 3.08.001 RD-T05-058 1

9 Left platen of head

hanging

3.06.01.048 RD-T05-054 1

10 Ironic shaft platen of

gauze(left)

2.01.02.090-04 RD-T05-061 1

Rear aluminum bearing

frame base assembly of

roller

2.03.04.039

12 Rear frame of roller 2.01.02.080-04 RD-T05-039 1

VI.2 Roller shell component

VR-231、VR-230

② Product Name 2.03.06.315 1

1 Roller shell component 2.01.02.087-04 RD-T05-059-01 1

2 Gauze lower frame 3.03.04.026 RD-T05-056AB 1

3 Right spring of head

hanging cover 3.03.01.020 RD-T05-038 1

5 Head hanging base 3.06.01.049 RD-T05-057AB 1

6 Right platen of head

hanging

2.01.02.091-04 RD-T05-062 1

7 Iron shaft platen of

gauze(right)

2.01.02.089-04 RD-T05-060-01 1

8 Gauze upper frame 3.08.002 RD-T05-058-01 1

9 Gauze assembly 3.06.01.048 RD-T05-054 1

10 Left platen of head

hanging

2.01.02.090-04 RD-T05-061 1

11 Ironic shaft platen of

gauze(left) 2.03.04.039

12 Rear aluminum bearing

frame base assembly of

roller

2.01.02.080-04 RD-T05-039 1

VI.3Roller core (II) component

③ Roller core (II)

component 2.03.06.311 1

1 Bolt barrier 2.01.01.336 RD-T05-096AB 2 φ2*φ5.5*1

2 Spring clamp of plastic

3.03.04.028 RD-T05-094AB 2

3 Locking plate of

plastic tube 2.01.01.133 RD-T05-097AB 2

4 Plate locking bolt 3.03.02.075 RD-T05-095AB 2 M3*20

5 Net pattern plastic tube 3.06.02.005 RD-T05-144 1

6 Ink shunt valve 3.06.02.004 RD-T05-093AB 1

7 Motor assembly of oil

2.03.05.023 1

8 Square shaft screw for

positioning of front

3.03.02.071 RD-T05-068-01 2

9 Eccentric block 3.03.06.012 RD-T05-078AB 1

10 Square shaft for

positioning of front

3.03.02.070 RD-T05-068 2

11 Positioning sheath 3.04.005 RD-T02-045AB 1

Fixing gasket of

positioning pillar at

front frame of rotary

2.01.01.139 RD-T05-140AB 2 φ5*φ12.5*1.5

13 Fixing screw at front

frame of roller

3.03.02.079 RD-T05-139AB 2 M5*10

14 Oil pump frame 2.01.01.132 RD-T05-077AB 1

15 Oil box fixing pillar 3.03.01.018 RD-T05-006AB 1

16 New 300DPIoil pump 3.03.06.057 RD-T13-112 1

17 Positioning shaft for

front frame

3.03.02.074 RD-T05-075 1

18 Oil sensor (finished

product)

2.03.05.032 1

19 Oil inspection base 2.01.01.135 RD-T05-098-01 1

20 Oil shunt valve gasket 2.01.02.092-03 RD-T05-093-02AB 1

21 Power frame in the

roller

2.01.01.134 RD-T05-098AB 1

VI.4 Front frame component of roller

④ Front frame component

of roller

2.03.06.326 1

1 Spanner cover of rotary

3.06.02.012 RD-T05-017 1

2 Spanner of rotary drum 2.01.02.079-04 RD-T05-017 1

3 Handle shaft 3.03.01.019 RD-T05-013 1

4 Hook lock of rotary

drum (left hook)

2.01.02.078-07 RD-T05-015 1

5 Plastic handle 3.06.01.047 RD-T05-014 1

6 Spring for hook lock of

rotary drum

3.03.04.023 RD-T05-016AB 1

7 Point welding

component of front

frame in roller

2.03.03.008-01 RD-T05-001-01 1

8 Braking frame 2.01.01.123 RD-T05-027AB 1

braking plate

2.03.01.034 RD-T05-029-01 1

10 Braking spindle 3.03.02.064 RD-T05-030AB 1

11 Braking frame spring 3.03.04.025 RD-T05-031AB 1

12 Oil motor and sensor

3.02.05.098 RD-T23-102 1

13 Socket box 2.01.01.121 RD-T05-024AB 1

14 Socket box cover of

rotary drum

2.01.01.122 RD-T05-025AB 1

15 Spring of Socket box

shaft at rotary drum

3.03.04.082 RD-T05-023AB 1

16 Socket box shaft 3.03.02.063 RD-T05-022AB 1

17 Socket lock plate

spring

3.03.04.024 RD-T05-026AB 1

18 Oil box tightening

sheath

3.03.03.046 RD-T05-004AB 1

socket lock

2.03.01.033 RD-T05-019-01 1

20 Supporting base of

socket

2.01.01.120 RD-T05-021 2

21 Supporting base 3.03.02.062 RD-T05-020 1

VI. 5 Ink Tank Part

⑤ Ink tank part 2.03.06.312 1

1 Ink tank switch spanner

sleeve

3.06.02.003 RD-T05-010AB 1

2 Ink tank switch spanner 2.01.02.077-04 RD-T05-010AB 1

3 Locating sleeve 3.04.005 RD-T02-045AB 2

4 Hex nut 3.05.02.002 2 M3

5 Optional plate of ink

3.06.01.046 RD-T05-008AB 1

6 Ink tank 3.06.01.044 RD-T05-007AB 1

7 Version II ink card

reader

3.02.36.004 1

8 Cover plate of ink tank

circuit panel

3.06.01.045 RD-T05-007-01AB 1

9 Tension spring of ink

tank switch board

3.03.04.022 RD-T05-012AB 1

10 Ink tank switch board 2.01.01.118 RD-T05-011AB 1

11 Ink switch cover 2.01.01.117 RD-T05-009AB 1

VI.6 Inner Core (I) Part of Roller

⑥ Inner core part (I) of

roller

2.03.06.329 1

1 Fixed plate of bearing 2.01.01.131 RD-T05-076 2

2 Right fixed plate of ink

distribution roller

2.06.00.002 RD-T05-136-01 1

3 Front plate of roller

core 2.01.01.129 RD-T05-066 1

4 608Z bearing 3.05.05.004 2

5 686ZZ bearing 3.05.05.006 2

6 Drum guide wheel

assembly

2.03.04.014 RD-T05-106 1

7 Spring of locating leg 3.03.04.031 RD-T05-122AB 2

of ink blockage plate

ink blockage plate

2.03.01.041 RD-T05-117-01 1

9 Oil copper bush (ink

roller)

3.04.034 RD-T05-105 1

10 Right ink blockage

3.06.01.053 RD-T05-114 1

11 Ink roller assembly 3.03.01.022 RD-T05-099 1

12 Drum supporting shaft 3.03.01.021 RD-T05-070 1

13 Ink distribution roller 3.03.01.023 RD-T05-108 1

14 Supporting plate

(roller)

2.02.00.004 RD-T05-069 1 Drilling

15 Supporting plate

(roller)

2.02.00.016 RD-T05-069 1 Without drilling

16 Spring of ink blockage

3.03.04.029 RD-T05-115AB 2

17 Spacer 2.01.02.026 RD-T02-063AB 2 φ6.1*φ13*0.2

18 Spring of ink blockage

3.03.04.030 RD-T05-120AB 2

19 Spring core 3.03.03.049 RD-T05-121AB 2

20 Bearing bush 3.04.040 RD-T05-135 2

21 Riveted part of locating

2.03.01.039 RD-T05-074-01AB 1

Riveted part of front

frame bearing adjusting

2.03.01.038 RD-T05-072-01AB 1

23 Flange nut 3.05.02.052 4 M5

VI.6 Inner Core (I) Part of Roller

24 Left ink blockage sheet 3.06.01.052 RD-T05-113 1

25 Riveted part of left ink

blockage plate

2.03.01.040 RD-T05-116-01 1

26 Oil copper bush (ink

roller)

3.04.032 RD-T05-103 1

27 Hex nut 3.05.02.003 1 M4

28 Aluminum bearing seat

assembly 2.03.04.037 1

29 General hex head cap

3.05.01.023 1 M4*16

30 Locating shaft 3.03.02.078 RD-T05-130-01 1

31 One-way spring washer 2.01.01.140 RD-T05-159AB 1 φ6.1*φ20*2

32 Fixed supporting shaft

of one-way tension

spring

3.03.02.080 RD-T05-158 1

One-way spring of

intermediate gear

assembly

3.03.04.032 RD-T05-160AB 1

34 Intermediate gear 3.04.039 RD-T05-131AB 1

35 Intermediate gear of

ink distribution roller

3.04.038 RD-T05-110 1

36 Driving gear of ink

distribution roller

3.04.037 RD-T05-109 1

37 Printing roller gear 3.04.033 RD-T05-104 1

38 Locating shaft 3.03.02.077 RD-T05-130 1

39 Left fixing blockage of

ink distribution roller

2.06.00.001 RD-T05-136 1

40 Rear plate of roller core 2.01.01.138 RD-T05-128 1

VI.7 Right Guide Rail Part of Roller

⑦ Right guide rail part of 2.03.06.335 1

roller

1 Spot welded assembly

of right and left guide

rails of roller

2.03.03.009 RD-T05-032-01 1

Riveted part of the

right frame of drum

guide wheel

2.03.01.036 RD-T05-035-01AB 1

3 Drum guide rail wheel 3.06.01.002 RD-T01-016AB 1

VI.8 Left Guide Rail Part of Roller

⑧ Left guide rail part of

roller

2.03.06.334 1

of right and left guide

rails of roller

2.03.03.009 RD-T05-032-01 1

Riveted part of the left

frame of drum guide

2.03.01.035 RD-T05-034-01AB 1 Change

3 Drum guide rail wheel 3.06.01.002 RD-T01-016AB 1

VI.9 Steel Mesh Part of Roller

⑨ Steel mesh part of

roller

2.03.06.336 1

1 Rear flange of roller 3.03.06.011 RD-T05-064 1

2 Seal ring of flange 3.06.03.015 RD-T05-065 2

3 Rear frame shaft 3.03.02.066 RD-T05-045 1

4 Gear 3.04.031 RD-T05-046 1

5 B4 steel mesh 3.08.023 RD-T05-063-02 1

6 Front flange of roller 3.03.06.010 RD-T05-063 1

VI.9 Steel Mesh Part of Roller

VC-21S、VC-20S

⑨ Steel mesh part of

roller

2.03.06.316 1

1 Rear flange of roller 3.03.06.011 RD-T05-064 1

2 Seal ring of flange 3.06.03.015 RD-T05-065 2

3 Rear frame shaft 3.03.02.066 RD-T05-045 1

4 Gear 3.04.031 RD-T05-046 1

5 A4 steel mesh 3.08.021 RD-T05-063-01 1

6 Front flange of roller 3.03.06.010 RD-T05-063 1

VII. Wastebasket Unit

1 Waste wax paper box

cover spring piece

2.01.02.462 RD-T14-039 2

2 Junction plate of

wastebasket

2.01.01.616 RD-T14-035 1

3 Wastebasket axial shaft

(A) 3.03.01.216 RD-T14-044 1

4 Lower shaft pulley

(wastebasket)

3.06.01.057 RD-T06-046AB 4

5 Driving spring of

plastic wheel

3.03.04.040 RD-T06-053AB 2

6 688Z bearing 3.05.05.007 2

8 Right wall board of

wastebasket

2.01.01.614 RD-T14-033 1

9 Door stopper seat 3.06.01.062 RD-T06-065 1

10 Door stopper 2.01.01.361 RD-T06-067 2

11 Door stopper magnet 3.10.005 RD-T06-068 1

12 Door stopper cover 3.06.01.063 RD-T06-066 1

13 Transmission plate of 2.03.05.042 1

right paperboard sensor

(finished product)

14 Cover shell of right

paperboard sensor

2.01.01.620 RD-T14-048 1

15 Fixed plate of sensor 2.01.01.390 RD-T06-017 1

16 Waste wax paper box

2.01.01.617 RD-T14-037 1

17 Lower shaft assembly

of wastebasket

3.03.01.215 RD-T14-043 1

18 Left wall board of

wastebasket

2.01.01.613 RD-T14-032 1

19 Microswitch (without

paper)

3.02.02.003 RD-T21-013AB 2 K3L

20 Biswitch seat of waste

wax paper box

2.01.02.463 RD-T14-041 1

21 STPD/STS-S3M model

180 synchronous belt 3.06.03.207 RD-A3-T13-196 1 S3M-180-5.5

22 Wastebasket motor

assembly

2.03.05.024 RD-T21-006AB 1

23 Fixed frame of

wastebasket motor

2.01.01.619 RD-T14-040 1

Synchronous belt

wheel of wastebasket

3.04.214 RD-T14-045 1

Riveted with "26" electric

pulley cover before being

delivered

25 Upper shaft driving

wheel of wastebasket

3.04.215 RD-T14-046 1

26 Electric pulley cover 2.01.01.073 RD-T03-020AB 1

Riveted with "24"

synchronous belt wheel

of wastebasket motor

before being delivered

27 Upper shaft of

wastebasket

3.03.01.214 RD-T14-042 1

28 Waste wax paper

poking leg

3.06.01.058 RD-T06-049AB 4

29 Rubber poking leg

(wastebasket)

3.06.03.019 RD-T06-050AB 2

30 Plastic pressure leg 3.06.01.060 RD-T06-055AB 3

31 Poking leg shell 2.01.02.268 RD-T06-051AB 2

VIII. Cutter Unit

1 Shim bed fame A 2.02.00.005-08 RD-T08-013 1 Delivered before being

attached with "2" shim

2 Shim 3.03.06.016 RD-T08-014AB 1

Delivered before being

attached with "1" shim

bed frame A

3 Riveted part of cutter

guide rail 2.03.01.045 RD-T08-016-01 1

4 Riveted part of left

fixed bracket

2.03.01.046 RD-T08-027AB 1

5 Cutter motor assembly 2.03.05.018 RD-T21-004AB 1

6 Cutter spacer 2.01.01.159 RD-T08-042AB 1

7 Tension roller 3.06.01.105 RD-T08-021AB 2

8 Motor gear 3.04.047 RD-T08-030AB 1

9 Broach gear 3.04.046 RD-T08-023AB 1

10 Limit board of shim 2.01.01.158 RD-T08-037AB 1

11 Limit column of cutter 3.03.02.094 RD-T08-039AB 2

12 Spring of limit column 3.03.04.044 RD-T08-041AB 2

13 Locating sleeve of

cutter

3.03.03.056 RD-T08-040AB 2

14 Microswitch (left and

right cutters)

3.02.02.006 RD-T21-016AB 2

15 Switchboard (right) 2.01.01.157 RD-T08-033-01AB 1

16 Cutter steel wire 3.03.06.014 RD-T08-004AB 1

17 Steel wirerope joint 3.03.03.055 RD-T08-005AB 2

18 Tension spring 3.03.04.042 RD-T08-006AB 1

19 Switchboard (left) 2.01.01.156 RD-T08-033AB 1

20 Cutter rack 3.06.01.104 RD-T08-015AB 1

21 Spring cover 3.06.01.103 RD-T08-011AB 1

22 Retainer spring 3.03.04.043 RD-T08-010AB 1

23 Shim 3.03.06.015 RD-T08-009AB 1

24 Steel ball 3.05.03.002 RD-T08-017AB 1 Sφ3.2

25 Right fixed frame 2.01.01.154 RD-T08-019AB 1

26 Cutter slider 3.06.01.101 RD-T08-007AB 1

27 Blade gear 3.06.01.102 RD-T08-008AB 1

IX. Plate-making Machine Unit

1 Fixed plate of bracket

frame 2.01.02.111-04

RD-T09-005-02AB 1

2 Spring of wax paper

cylinder racket

3.03.04.045 RD-T09-007-07AB 2

3 Bracket column of wax

paper cylinder 3.03.02.095 RD-T09-007-06AB 2

4 Supporting plate 1 of

wax paper cylinder

2.01.02.110-04 RD-T09-005-01AB 1

5 Bracket testing slider

cover 2.01.02.112-04

RD-T09-007-04AB 2

6 Slider of wax paper

cylinder testing frame

3.06.01.110 RD-T09-007-03AB 2

7 Bracket seat of wax

paper cylinder

3.06.01.108 RD-T09-007-01AB 1

8 Fixed plate of

supporting frame

2.01.01.162 RD-T09-006AB 1

of plate-making

baseboard

2.03.03.011-01 RD-T09-004-01 1

10 Testing bracket of wax

paper cylinder

3.06.01.109 RD-T09-007-02AB 1

11 Version II wax paper

card reader

3.02.36.003 1

12 Blanking plate of

testing bracket

3.06.01.111 RD-T09-007-05AB 1

13 Left bracket of thermal

head foot 2.01.01.165

RD-T09-024AB 1

14 Printing stepper motor 3.02.01.010 RD-T21-010AB 1 23HD222-13Y

15 Hanging bracket cover 3.03.03.068 RD-T09-026AB 2

16 Fixed plate of motor 2.01.01.172 RD-T09-048AB 1

17 Riveted part of

plate-making left frame

2.03.01.047 RD-T09-001-01AB 1

19 Riveted part of main

motor tension plate

2.03.01.050 RD-T09-044-01AB 1

20 Motor shaft gear 3.04.051 RD-T09-047AB 1

21 Driving wheel of motor

3.04.050 RD-T09-046AB 1

22 Driving belt wheel of

3.06.01.118 RD-T09-039AB 1

23 Synchronous belt A 3.06.03.020 RD-T09-049AB 1 S3M-159-6

24 Synchronous belt

wheel of rubber shaft

3.06.01.117 RD-T09-038AB 1

25 Synchronous belt (B) 3.06.03.021 RD-T09-057AB 1 S3M-186-6

26 Plate-making machine

torque cover

3.03.03.070 RD-T09-092AB 1

27 Belt tension sleeve 3.04.049 RD-T09-043AB 2

28 corrugated gasket of

torque cover

3.05.04.003 RD-T09-095AB 1 φ14.5*φ18.5*0.3

29 608Z grooved bearing 3.05.05.011 2

30 Stationary shaft of belt

3.03.02.101 RD-T09-040AB 1

31 Thermal head pressure

adjusting frame

2.01.01.164 RD-T09-023AB 1

32 Hex nut 3.05.02.003 3 M4

33 Fine-tuning block 2.01.02.124-03 RD-T09-074AB 2

34 Plate-making tension

spring

3.03.04.048 RD-T09-075AB 2

35 Fixed leg of carrier

plate (left)

2.01.01.177 RD-T09-093AB 1

36 Riveted part of

plate-making right

2.03.01.048

RD-T09-002-01AB 1

37 Thermal head frame

adjusting handle

3.06.01.116 RD-T09-021AB 1

38 Stationary column of

tension sleeve 3.03.02.103 RD-T09-042AB 1

39 Main tension spring of

handle

3.03.04.047 RD-T09-022AB 1

STPD/STS-S4.5M

model 284 synchronous

3.06.03.013 RD-T04-038AB 1 RD-T04-038AB

Synchronous belt part

of plate-making sponge

roller

2.03.06.428

Riveted part of paper

delivery driving chain

wheel B

RD-T03-016-04AB 1 Without coding, riveted

by the plant itself.

43 Riveted part of frame

adjusting handle

2.03.01.049 RD-T09-020-06AB 1

44 Pulley 3.03.03.063 RD-T09-020-03AB 1 φ6*φ9.5*4.5

45 Riveted part of frame

adjusting handle

2.03.01.049 RD-T09-020-06AB 1

46 Fixed plate of motor

2.01.01.173 RD-T09-048-02AB 1

47 Wax paper delivery

motor assembly

2.03.05.029 RD-T21-023AB 1 TG-38243000-90K

48 Right frame of thermal

head foot

2.01.01.166 RD-T09-025AB 1

49 Fixed leg of carrier

plate (right)

2.01.01.178 RD-T09-094AB 1

plate insert

3.06.01.119 RD-T09-050-05AB 1

2.02.00.007-08 RD-T09-050

52 Static brush of

plate-making machine 3.09.004

RD-T09-050-03 1

53 Pressure board of static

2.02.00.008 RD-T09-050-01 1

54 Fixed supporting plate

shaft of sensor 3.03.01.035 RD-T09-058 2

55 Wax paper tail sensor

plate (finished product) 2.03.05.001 RD-T22-001AB 1

of sensor

2.01.01.174 RD-T09-059AB 1

57 Axial shaft 3.03.01.038 RD-T09-061 2

(58) Drilling part of

plate-making machine

2.03.06.427 1

59 Thermal plate-making

roller

3.03.01.032 RD-T09-034 1

60 Left supporting plate of

thermal head

2.01.01.168 RD-T09-030-01AB 1 Equipped with Toshiba

printing head

60 Left supporting plate of 2.01.01.167 RD-T09-030AB 1 Equipped with Kyocera

thermal head printing head

61 2011-7 model B4

printing head (Toshiba) 3.02.10.008

1 TPH260R49

61 B4 printing head

(Kyocera)

3.02.10.003 1 KRD-260-12GAZ4-NRH

62 Fixed column of

thermal head (2)

3.03.02.106 RD-T09-088-01AB 3 Length: 7.5mm，equipped

with Toshiba printing

62 Fixed column of

thermal head (2)

3.03.02.107 RD-T09-088-01AB 3 Length: 8.5mm，equipped

62 Fixed column of

thermal head

3.03.02.105 RD-T09-088AB 3 equipped with Kyocera

printing head

63 Fixed column of

thermal head frame (2)

3.03.02.100 RD-T09-029-01AB 2

Spot welded assembly

of thermal head

supporting plate

2.03.03.014-03 RD-T09-028-04 1

Equipped with Toshiba

printing head, delivered

together with "62" fixed

column of thermal head

Spot welded assembly

of thermal head

supporting plate

2.03.03.013-03 RD-T09-028-02 1

Equipped with Kyocera

printing head, delivered

together with "62" fixed

column of thermal head

65 Right supporting plate

of thermal head

2.01.01.170 RD-T09-031-01AB 1 Equipped with Toshiba

printing head

of thermal head

2.01.01.169 RD-T09-031AB 1 Equipped with Kyocera

printing head

66 Sponge roller assembly 3.03.01.033 RD-T09-052 1

VR-231、VR-230

plate insert

3.06.01.119 RD-T09-050-05AB 1

2.02.00.007-08 RD-T09-050

52 Static brush of

plate-making machine 3.09.004

RD-T09-050-03 1

53 Pressure board of static

2.02.00.008 RD-T09-050-01 1

shaft of sensor 3.03.01.036 RD-T09-058-01 2

55 Wax paper tail sensor

plate (finished product) 2.03.05.001 RD-T22-001AB 1

of sensor

2.01.01.174 RD-T09-059AB 1

57 Axial shaft 3.03.01.038 RD-T09-061 2

(58) Drilling part of

plate-making machine

2.03.06.427 1

59 Thermal plate-making

roller

3.03.01.032 RD-T09-034 1

60 Left supporting plate of

thermal head

2.01.01.168 RD-T09-030-01AB 1

61 A4-300DPI printing

head (Toshiba) 3.02.10.009

1 TPH217R25

62 Fixed column of

thermal head (2)

3.03.02.106 RD-T09-088-01AB 3 Length: 7.5mm

62 Fixed column of

thermal head (2)

3.03.02.107 RD-T09-088-01AB 3 Length: 8.5mm

63 Fixed column of

thermal head frame (2

3.03.02.100 RD-T09-029-01AB 2

64 Welded part of fixed

plate holding board

2.03.03.014-03 RD-T09-028-04 1

of thermal head

2.01.01.170 RD-T09-031-01AB 1

66 Sponge roller assembly 3.03.01.033 RD-T09-052 1

X. Draft Scanning Unit

VR-231B、VR-231、VC-21S

Riveted part of

scanning cover locating

2.03.01.053-03 RD-T10-068-01 2

2 Scanning cover

locating screw

3.03.02.113 RD-T10-069 2

3 Oil copper sleeve 2 3.04.054 RD-T10-034 6

4 First and second paper

feed gears

3.06.01.125 RD-T10-031 3

5 First paper feed driving

3.06.01.124 RD-T10-029 1

6 Motor driving gear B 3.06.01.123 RD-T10-018 1

7 Scanner motor spacer 2.01.02.270-03 RD-T10-026 1

8 Draft scanning stepper

3.02.01.013 RD-T21-009 1 PM42L-048-100

VR-231B、VR-231、VC-21S

9 Lower scanning paper

deflector 2.01.02.126 RD-T10-020 1

10 Scanning roller 3.03.01.044 RD-T10-033 1

11 Locating plate of

scanning head (right) 2.01.01.379 RD-T10-063 1

12 Scanner spring 3.03.04.049 RD-T10-037 2

13 Guidepost of scanner

pressure spring

3.03.02.111 RD-T10-035 2

14 Fixed seat of scanner 2.01.01.375 RD-T10-036 2

15 Paper delivery 2.01.01.612 RD-T14-081 1

supporting plate

16 Fixed leg of paper

deflector

2.01.01.372 RD-T10-021 4

scanning frame

2.03.01.052 RD-T10-040-01 1

rubber roller

3.03.01.043 RD-T10-030 1

19 First paper feed rubber

roller

3.03.01.042 RD-T10-023 1

of scanner

2.01.01.376 RD-T10-038 1

21 Receiving fixing frame 2.01.01.380 RD-T10-064 1

Scanning receiving

sensor (finished

product)

2.03.05.013 RD-T22-037 1

23 Axial shaft 3.03.01.041 RD-T10-014 1

24 Rived part of left

scanning frame

2.03.01.051 RD-T10-011-01 1

25 Scanning shield sheet 2.01.02.264-01 RD-T10-042 1

26 Locating plate of

scanning head (left)

2.01.01.378 RD-T10-062 1

27 Hualing single-tube

scanning head

3.02.09.002 RD-T22-039 1 P3R256-6598-6B-XXXXX

27 A4-300DPI scanning

3.02.09.006 1 DL515-04UHT

VR-231B、VR-231、VC-21S

Scanning transmission

sensor (finished

product)

2.03.05.012 RD-T22-036 1

29 Scanning cover 3.06.01.121 RD-T10-001 1

30 Right inner seat of

scanning cover 2.01.01.368 RD-T10-003 1

2.01.01.384 RD-T10-077 2

32 Second paper feed 2.01.01.382 RD-T10-072 1

driven roller seat

(right)

33 First paper feed frame

of scanning cover

2.01.01.369 RD-T10-004 2

First paper feed frame

seat of scanning cover

(left)

2.01.01.370 RD-T10-004-01 1

35 Hex nut 3.05.02.002 4 M3

36 Plate cover 3.06.01.122 RD-T10-012 2

37 Paper deflector of

cover 2.01.02.125-01 RD-T10-010 1

38 Frame spring (right) 3.03.04.050 RD-T10-074 2

driven roller

3.03.01.040 RD-T10-008 1

40 Frame spring (left) 3.03.04.051 RD-T10-075 2

41 Frame spring bolt 3.03.02.114 RD-T10-076 4

42 First paper feed roller

of cover

3.03.01.039 RD-T10-006 1

43 First paper feed frame

seat of cover (right) 2.01.01.371 RD-T10-004-02 1

driven roller seat (left) 2.01.01.383 RD-T10-073 1

45 Left inner seat of cover 2.01.01.367 RD-T10-002 1

XI. Label Unit

1 Model label 3.07.02.228 RD-T14-056 1 VR-230

1 Model label 3.07.02.229 RD-T14-056 1 VR-231

1 Model label 3.07.02.232 RD-T14-056 1 VR-231B

1 Model label 3.07.02.243 RD-T14-056 1 VR-230B

2 Model label 3.07.02.230 RD-T14-057 1 VC-20S

2 Model label 3.07.02.231 RD-T14-057 1 VC-21S

3 Model label 3.07.02.244 RD-T14-056-01 1 BPS-125

3 Model label 3.07.02.245 RD-T14-056-01 1 BPS-125P

4 Failure indication label

(Chinese) 3.07.02.237 RD-T14-058 1

VR-231 、 VR-231B 、

VR-230、VR-230B

(Chinese) 3.07.02.248 RD-T14-058-01 1

VC-21S、VC-20S

(English) 3.07.02.238 RD-T14-059 1

VR-231 、 VR-231B 、

VR-230、VR-230B

6 AIO machine No. label

(Chinese) 3.07.03.101 RD-T14-076 1 VR-231

(Chinese) 3.07.03.102 RD-T14-076 1 VR-231B

(Chinese) 3.07.03.103 RD-T14-076 1 VR-230

(Chinese) 3.07.03.104 RD-T14-076 1 VR-230B

(Chinese) 3.07.03.105 RD-T14-077 1 VC-21S

(Chinese) 3.07.03.106 RD-T14-077 1 VC-20S

(English) 3.07.03.107 RD-T14-076-01 1 VR-231

(English) 3.07.03.108 RD-T14-076-01 1 VR-231B

(English) 3.07.03.109 RD-T14-076-01 1 VR-230

(English) 3.07.03.110 RD-T14-076-01 1 VR-230B

(South Africa) 3.07.03.111 RD-T14-075 1 BPS 125

(South Africa) 3.07.03.112 RD-T14-075 1 BPS 125P

10 Wastebasket warning

label (Chinese) 3.07.02.246 RD-T14-049-01 1

11 Wastebasket warning

label (English) 3.07.02.247 RD-T14-049-02 1

12 Notice label (Chinese) 3.07.02.035 RD-T09-068AB 1

13 Notice label (English) 3.07.02.036 RD-T09-068-01AB 1

14 Cutter "Notice" label

(Chinese) 3.07.02.033 RD-T09-067AB 1

15 Cutter "Notice" label

(English) 3.07.02.034 RD-T09-067-01AB 1

Function selection

instruction label

(Chinese)

3.07.02.249 RD-T14-058-02 1 VR-231 、 VR-231B 、

VC-21S

Function selection

instruction label

(English)

3.07.02.250 RD-T14-058-03 1 VR-231、VR-231B

18 Power switch label

(Chinese) 3.07.02.018 RD-T07-052 1

19 Power switch label

(English) 3.07.02.019 RD-T07-052-01 1

20 Power socket label

(Chinese) 3.07.02.016 RD-T07-051 1

21 Power socket label

(English) 3.07.02.017 RD-T07-051-01 1

22 Pressure label

(Chinese) 3.07.02.023 RD-T07-054AB 1

23 Pressure label (English) 3.07.02.024 RD-T07-054-01AB 1

24 Inching switch label

(Chinese) 3.07.02.029 RD-T07-066AB 1

25 Inching switch label

(English) 3.07.02.030 RD-T07-066-01AB 1

26 Wastebasket label 3.07.02.236 RD-T14-049 1

27 Protective earthing

label 3.07.02.090 RD-T07-123AB 1

28 Cutter button label

(Chinese) 3.07.02.027 RD-T07-065AB 1

29 Cutter button label

(English) 3.07.02.028 RD-T07-065-01AB 1

Thermal head

separation and union

label (Chinese)

3.07.02.025 RD-T07-064AB 1

Thermal head

separation and union

label (English)

3.07.02.026 RD-T07-064-01AB 1

32 Forward paperboard

lifting label (Chinese) 3.07.02.011 RD-T07-048 1

33 Forward paperboard

lifting label (English) 3.07.02.012 RD-T07-048-01 1

34 Roller rotation notice

label (Chinese) 3.07.02.007 RD-T05-180AB 1

35 Roller rotation notice

label (English) 3.07.02.008 RD-T05-180-01AB 1

36 Left label of paper

delivery support 3.07.02.003 RD-T03-001-01 1

37 Right Paper delivery

support label 3.07.02.004 RD-T03-001-02 1

38 Original paper 3.07.02.020 RD-T07-053 1

specification label (A3)

39 Paper model label (left) 3.07.02.233 RD-T14-029 1

40 Paper model label

(right) 3.07.02.234 RD-T14-030 1

41 Vertical label of paper

model 3.07.02.235 RD-T14-031 1

Left label of original

paper specification

scanning

3.07.02.239 RD-T14-082 1 VR-231B、VC-21S

Right label of original

paper specification

scanning

3.07.02.241 RD-T14-084 1

VR-231B、VC-21S

Left label of original

paper specification

scanning

3.07.02.240 RD-T14-083 1

VR-231

Right label of original

paper specification

scanning

3.07.02.242 RD-T14-085 1

VR-231

XII. Circuit Unit

Connector position in section A

原稿检测发射： original inspection and launch 原稿到位发射： original in place and launch 卸版发射传感器：plate unload and

launch sensor 右卡纸发射传感器：right paper jab launch sensor 原稿检测光电传感器： original inspection photosensor 原

稿到位光电传感器： original in place photosensor 卸版接收传感器： unload receiving sensor 右卡纸接收传感器：right

paper jam receiving sensor 天地初始槽光电传感器：initial groove photosensor 天地编码槽光电传感器： code

groove photosensor 去扫描头： remove scan head A 区接插件位置图: connector position in section A 去打印头：Remove

print hear 去电脑联机：Disconnect from PC 绿： Green 棕： brown 白： white 黄： yellow 黑：black 蓝：blue A

模式型槽光电： Mode A groove photosensor 油漆检测光传感器：paint inspection photosensor 版夹：clamp bar B

模式槽型光电： Mode B groove photosensor 装卸版位槽型光电：Load and unload groove photosensor 印纸张数槽型光

电： paper number groove photosensor 滚筒停止位槽型光电： roller stop groove photosensor 蜡纸尾部反射传感器:

stencil end reflect sensor 滚筒版纸光传感器： roller typographic paper photosensor 上盖微动开关： upper cover inches

switch 无纸微动开关： no-paper inches switch 锁纸微动开关： paper lock inches switch 废纸箱满微动开关： full

waste basket inches switch 前门微动开关： front door inches switch 切刀左微动开关：left cutter inches switch 切刀

右微动开关：right cutter inches switch 切刀点动微动开关： cutter inching switch 滚筒到位微动开关：roller in place inches

switch 滚筒点动微动开关： roller inching switch 点-点电路图：point-point circuit diagram 区接插件位置图：connector

position in section B 主电机编码：Main Motor coding 制版控制： platemaking control C 区接插件位置图:

connector position in section C 油墨读卡器：printing ink card reader 控制面板：control panel 蜡纸读卡器：stencil card reader

打印步进电机：printing stepper motor 扫面步进电机： scanning stepper motor D 区接插件位置图：connector

position in section D 主电机插座：main motor socket 天地电机：tiandi motor 切刀电机：cutter motor 版夹电机：clamp

motor AC 电源控制：AC power control 蜡纸输送电机：stencil feeding motor 油泵电机：oil pump motor 废纸箱电机：

Waste basket motor

Connector position in section B

扫描头：scan head 原稿到位发射：original in place and launch 原稿检测发射： original inspection and launch 原稿检测光

电传感器：original in place photosensor 原稿到位光电传感器：original in place photosensor 卸版发射传感器：unload

receiving sensor 右卡纸发射传感器：right paper jab launch sensor 卸版接收传感器：unload receiving sensor 右卡纸接收

传感器：right paper jam receiving sensor 天地初始槽型传感器：initial groove photosensor 天地编码槽型光电传感器： code

groove photosensor 去扫描头：remove scan head 打印电压控制（主板）printing voltage control (mainboard)_ 去电脑联机：

Disconnect from PC 副电源板：standby power panel 去打印头：remove print head 打印头： Print head

Connector position in section C

B 模式槽型光电： Mode B groove photosensor 装卸版位槽型光电：Load and unload groove photosensor 印纸张数槽型

光电： paper number groove photosensor 滚筒停止位槽型光电： roller stop groove photosensor 蜡纸尾部反射传感器:

stencil end reflect sensor 滚筒版纸光传感器： roller typographic paper photosensor 上盖微动开关： upper cover inches

switch 无纸微动开关： no-paper inches switch 锁纸微动开关： paper lock inches switch 废纸箱满微动开关： full

waste basket inches switch 前门微动开关： front door inches switch 切刀左微动开关：left cutter inches switch 切刀

右微动开关：right cutter inches switch 切刀点动微动开关： cutter inching switch 滚筒到位微动开关：roller in place inches

switch 滚筒点动微动开关： roller inching switch 点-点电路图：point-point circuit diagram

Connector position in section D

C 油墨读卡器：printing ink card reader 控制面板：control panel 蜡纸读卡器：stencil card reader 打印步进电机：printing

stepper motor 扫面步进电机： scanning stepper motor 油泵电机：oil pump motor 废纸箱电机：Waste basket motor

蜡纸输送电机：stencil feeding motor

主电机：main motor 副电源板： standby power panel 扫描步进电机：scanning stepper motor

打印步进电机：printing stepper motor 主电机插座：main motor socket

XII. Circuit Unit

打印头:print head 主控板: main control board AC220V 插座:AC 220V socket 主电源板：Main power panel 副电源板：

standby power panel

Original test, original

in-place and right

paperboard testing

sensor wires

3.02.05.267 VR-231-009 1

2 Connecting wire from

scanning head to main

3.02.05.265 VR-231-005 1 VR-231B 、 VR-231 、

VC-21S

3 Main board +5V power

wire 3.02.05.274 VR-231-022 1

4 USB connecting wire 3.02.05.283 VR-231-061 1

5 B4、A3 data printing

wire 3.02.05.070 RD-T23-072 1

3108、4019、3208、4029、

4300B-08，equipped with

Kyocera printing head

5 B4 new print head data

3.02.05.082 RD-T23-085 1 4029-008A ， equipped

6 Wires from main board

to various sensors

3.02.05.268 VR-231-010 1

7 Main motor grating

sensor wire

3.02.05.250 RD-300DPI-016 1

8 Printing power control

3.02.05.266 VR-231-007 1

9 Main motor grating

sensor wire

3.02.05.258 RD-300DPI-053 1

10 Control panel display

3.02.05.251 RD-300DPI-018 1

11 Wax paper electronic

label connecting wire

3.02.05.257 RD-300DPI-052 1

12 Printing stepping motor

3.02.05.272 VR-231-015 1

13 Scanning stepping

motor wire

3.02.05.273 VR-231-016 1 VR-231B 、 VR-231 、

VC-21S

14 Primary and secondary

power wires

3.02.05.248 RD-300DPI-013A 1

15 Microswitch sensor

3.02.05.269 VR-231-011 1

Wires from main panel

to cutter, clamp bar and

vertical motors

3.02.05.271 VR-231-014A 1

17 Wires from main panel 3.02.05.270 VR-231-013A 1

to wastebasket, ink

pump and wax paper

transmission motors

18 B4 printing head power

wire 3.02.05.010 RD-T23-011 1

3108 、 4019 、 3208 、

4029-013，equipped with

Kyocera printing head

18 B4 new print head

power wire 3.02.05.083 RD-T23-086 1

4029-013A ， equipped

19 Primary and secondary

power wires 3.02.05.248 RD-300DPI-013A 1

Wires from B4 switch

to primary and

secondary power

supplies

3.02.05.012 RD-T23-013 1

3108 、 4019 、 3208 、

4029-015

21 B4 AC wire（switch to

power supply） 3.02.05.011 RD-T23-012 1

3108 、 4019 、 3208 、

4029-014

B4 earth wire

（connecting wire

between wastebasket

and wall board）

3.02.05.013 RD-T23-014 1

3108、4019、3208、4029、

4300B-16

23 Power supply wire 3.02.05.110 RD-T22-020AB 1

Duplicator BPS-125 Parts Manual

Documents