Post on 02-Jan-2021
transcript
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
PaperPrint headPrint Head
RIPRIP Fabrics/
Substrate
Heat Press
• Chemical
Compatibility
• Jetting
Performance
• Reliability
• Ink absorption/less
cockling
• Release efficiency
• Image Quality
Stability and
Shelf Life
• Chemical Affinity
• Durability - Physical
• Durability - Light
• Image Quality
• Ink Stability to aging
• Ink Stability to Environments
(shipping/Storage)
• Transfer energy
• Transfer Efficiency
• Ink Specific Profiling
• Ink Specific color
Matching
• Proper Printmode for
application
INK
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
Transfer Sublimation Style Direct Sublimation Style
GF 1480 Poplin DD 1481 Poplin
GF 1701 Primary Flag DD 7701 Primary Flag
GF 1707 Soft Knit DD 7707 Soft Knit
GF 1709 Heavy Knit DD 7709 Heavy Knit
GF 1710 Poly Stretch DD 7710 Poly Stretch
GF 4017 Soft Knit DD 7817 Soft Knit
GF 4019 Nirvana B.O.B. DD 4419 Nirvana B.O.B.
GF 4020 Nirvana Purity DD 4420 Nirvana Purity
GF 6088 MoJo® DD 6788 MoJo®
GF 6180 Econo Knit DD 3268 Econo Knit
GF 7176 Supreme Knit DD 7276 Supreme Knit
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
••
•
•
•
•
••
••
•
•
•
•
•
•
•
SURFACE PRESS TIME TEMP PRESSURE TIPS
Polyester
Material
35-40
seconds
400°F 40 psi
(medium)
Pre-press shirt for 3-5 seconds to eliminate moisture. Tack spray
transfer and use blow-out sheet to avoid ghosting.
Apparel 45-55
seconds
380-390°F 40 psi
(medium)
Look for a tight knit and high white point for more brilliant color.
Polyester/Mouse
Pads
45 seconds 400°F 40 psi
(medium)
Look for a tight knit and high white point for more brilliant color.
Metal (Unisub) 60 seconds 375-400°F 40 psi
(medium)
Time varies with metal mfg (always consult for correct time and
temp). Place absorbent sheet on bottom of heat press. Then
place product transfer side down on top of the absorbent sheet.
Unisub Products 60 seconds 400°F 40 psi
(medium)
Remove plastic coating. Tear transfer paper away immediately
after pressing.
FR Plastics 60-75
seconds
400°F 40 psi
(medium)
Remove plastic coating. Tear transfer paper away immediately
after pressing.
Ceramics/Mugs 150-210
seconds
350-400°F 40 psi
(medium)
Time varies with press. Press into silicon pad. Mugs should be
cooled down after transfer paper is removed in either a bucket
of warm water or using a cooling plate.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Optimization
ICC
Profile
Total Ink
Limit
Linearization
Primary Ink Restrictions
RIP and Print Settings
Set Up Printer & Media
Environmental Conditions