Post on 12-Sep-2021
transcript
Geophysics 424E2.4
© Martyn Unsworth, University of Alberta, October 2016 1
E2.4 Applications of near field frequency domain EM techniques
E2.4.1 Instrumentation E2.4.1.1 Instrumentation for ground based surveys
EM31 EM34
EM38
Data generally presented as a map of terrain conductivity, which is the average conductivity from the surface to a depth ~ TX-RX offset.
Technique effective at mapping a large area quickly.
Direct contact with the ground is not needed. The electric current in the ground is
generated through induction. This can be important if the topsoil is contaminated, or frozen.
Doesn’t give vertical variation of conductivity with depth as easily as a DC
resistivity survey.
Multiple TX-RX offsets can be used to get estimates of the depth variations with the EM34.
Different TX orientations have different penetration depths..
Beware of wire fences as a source of high conductivity.
Geophysics 424E2.4
© Martyn Unsworth, University of Alberta, October 2016 2
E2.4.1.2 Instrumentation for airborne EM surveys
Airborne EM works best where conductive ore bodies such as massive sulphides are found in very resistive shield areas where land access is difficult (e.g. about half of Canada!)
Compared to ground based EM systems, the vertical distance from the TX-RX
system to the target is large. This makes the in-phase and quadrature anomalies quite small ( typically ppm)
Bucking coil used to suppress the primary magnetic field at the RX. This allows a
weaker secondary field to be detected. Multiple coil configurations are used. This allows 9 combinations of TX and RX
to be used. These will couple differently with different conductor geometries.
Multiple frequencies give estimate of depth variation of conductivity. Palacky and West (1991), Figure 11.
Geophysics 424E2.4
© Martyn Unsworth, University of Alberta, October 2016 3
Measurements can be contaminated by EM noise, such as lightning strikes (also
called spherics). See Palacky and West, (1991), Figure 14. The top panel of the figure shows the same line recorded on a normal day and one with a lot of thunderstorm activity. Lower panel shows same profiles after filtering.
Signal in an MT survey is noise in an airborne EM survey!!!!!!!!
Flight lines collected on a grid. Palacky and West (1991), Figure 19. Typical anomaly map from Aerodat survey in Quebec. This shows variation of real and imaginary responses.
Depth of penetration depends on both TX-RX distance, frequency and the skin depth.
Geophysics 424E2.4
© Martyn Unsworth, University of Alberta, October 2016 4
Measuring weak secondary magnetic fields in the presence of the primary magnetic field is difficult
Example 1
The RX and TX are on a helicopter boom 5 m apart. What is the change in HP if the boom flexes and this distance changes by 1 cm?
H p
z = -IA/ 4πr3
If the TX-RX distance changes by a distance Δr, then
pz
pz
pz
H
ΔHH =
3
rr
r=
3
500
501
% = 6012 ppm
Example 2 The RX is towed 100 m behind the aircraft and oscillates by 2 m
pz
pz
pz
H
ΔHH = 100 x
3
rr
r= 61,000 ppm
Very strong conductors have little quadrature response. Thus the best targets in
mineral exploration are the most difficult to detect with frequency domain EM!
Multiple frequencies can be used to estimate conductivity – depth variations. See example in C5.5.2.
Data displayed as a ground (terrain) conductivity map. Sometimes expressed as secondary field / primary field as ppm.
E2.4.2 Environmental and groundwater surveys
See examples of ground based EM surveys in E2.1
Saline groundwater contamination (contaminated water is conductive). This problem can also occur during oil extraction or as a consequence of irrigation.
Ground conductivity map derived from a DIGHEM survey. The example on the left shows leakage from tailings ponds at a mine. ● Acid mine drainage ● Locating buried oil drums and tanks
http://www.fugroairborne.com.au/service/images/env_downloads/CONTAMINANT_MAPPING.pdf
Geophysics 424E2.4
© Martyn Unsworth, University of Alberta, October 2016 5
● Contamination of ground water by organic liquids. These include both light and dense non-aqueous phase liquids (LNAPLS and DNAPLS) such as hydrocarbons and CCl4 and are generally resistive.
● Mapping salinity of groundwater, especially with regard to salt water intrusion
56 kHz DIGHEM survey in the Everglades
7.2 kHz DIGHEM survey in the Everglades
http://www.fugroairborne.com.au/service/images/env_downloads/EVERGLADES.pdf
See examples http://www.fugroairborne.com.au/service/images/env_downloads/
Geophysics 424E2.4
© Martyn Unsworth, University of Alberta, October 2016 6
E2.4.3 Geotechnical applications
DIGHEM data can be used to map the depth of topsoil, and avoid bedrock during the construction of pipelines.
http://www.fugroairborne.com.au/resources/case_studies/engineering/pdfs/PipelinePlanning.pdf Can also map paleochannels prior to construction (or for groundwater exploration) http://www.fugroairborne.com.au/service/images/env_downloads/PALEO_CHANNEL.pdf
E2.4.4 Mineral exploration
Frequency domain EM techniques were originally developed for mining applications. The first systems were ground based (and are still used today), but the real value has been proven in airborne EM techniques where huge areas can be covered very quickly.
E2.4.4.1 Kimberlite exploration with DIGHEM
Kimberlite pipes will exhibit both induced and remnant magnetization. Depending on the age of the pipe, the remnant magnetization can be either normal or reversed.
The magnetic anomaly is due to a combination of induced and remnant magnetization. This can result in a positive, negative or zero anomaly, as is the case for pipes at Ekati Mine. Grizzly pipe has a negative magnetic anomaly and Panda has a small positive anomaly. Koala pipe shows a weak anomaly.
Geophysics 424E2.4
© Martyn Unsworth, University of Alberta, October 2016 7
Kimberlite pipes are often characterized by a low resistivity zone at the surface, as the pipe weathers to clay and erosion forms a lake that saturates the clay with water.
The Ekati Diamond Mine is exploiting five economic kimberlite pipes in the Lac
de Gras region of the NWT (Panda, Koala, Misery, Fox and Leslie). BHP Billiton mining operations at the Koala Pipe are shown above.
Airborne EM data can provide an alternative way of locating kimberlite pipes.
The apparent resistivity map calculated from the 7200Hz coplanar data of the DIGHEM survey (see below) clearly shows the economic pipes in this data block. The Koala and Panda kimberlite pipes give clear EM anomalies, and are also underneath lakes.
Geophysics 424E2.4
© Martyn Unsworth, University of Alberta, October 2016 8
More details can be found at : http://www.fugroairborne.com.au
http://www.mining-technology.com/projects/ekati http://ekati.bhpbilliton.com
E2.4.4.2 Massive sulphide exploration
DIGHEM data from Voisey’s Bay, which is a very large massive sulphide deposit in Labrador
http://www.fugroairborne.com.au/resources/case_studies/minerals/voiseys.html
Geophysics 424E2.4
© Martyn Unsworth, University of Alberta, October 2016 9
E2.4.4.3 Other mineral applications of airborne geophysics
http://www.fugroairborne.com.au/resources/case_studies/minerals/index.html
Telford Figure 7.77: Turair is a hybrid technique with a large TX on the ground and the RX airborne. In this example (Manitoba Nickel Belt) a massive sulphide was detected at a depth of 500 feet. Turair has good depth penetration owing to the large ground based TX loop that generates stronger signals than the ~ 1 m diameter loop in the air.
Why is the field strength ratio positive over the conductor? The small in-phase response suggests that this is a good conductor (why does
small phase angle response mean that the in-phase component is small?). The second part of the example is a little lacking in specifics about location etc,
but shows the effect of increasing altitude. The larger phase difference suggests this is not such a good conductor.
E2.4.5 Detection of UXO (Unexploded Ordinance) and landmines
Figures from Huang and Won (2003) Study from test site with ferrous (circle) and non-ferrous (square) targets Magnetic data only detect ferrous targets Conductivity measurements more reliable way to find all targets Magnetic data also complicated by variation in soil properties
Figures below from Won et al., 2001 In more advanced techniques, the in-phase and quadrature components are
measured at multiple frequencies. These EM induction spectra (EMIS) can be effective in identifying a
specific UXO (e.g. mine, shell, rocket, scrap metal etc.) EMIS spectrum of each UXO has its own distinct characteristics and
distinguishing qualities UXO signature libraries available for operator in real-time
Geophysics 424E2.4
References
Huang, H., and I.J. Won, Automated anomaly picking from broadband EM data in an unexploded ordinance (UXO) survey, Geophysics, 68, 1870-1876, 2003.
Hutchinson et al, Geophysical Applications to Solid waste analysis, in Proceedings of the Sixteenth International Conference on Solid Waste Technology and Management Philadelphia, PA U.S.A., December 10-13, 2000 Editors: Zandi, I.; Mersky, R.L.; Shieh W.K. Pp. 2-68 to 2-78 ISSN 1091-8043.
Palacky and West (1991), chapter 10 in “Electromagnetic methods in Applied Geophysics – Volume 2 - Applications –Part B”, edited by Misac Nabighian, and published by the SEG.
McKenzie, R.C., R.J. George, S.A. Woods, M.E. Cannon, D.L. Bennett, Use of the Electromagnetic-Induction Meter (EM38) as a tool in managing salinisation, Hydrogeology Journal, 5 (1), 1997.
Won, I.J., D.A. Keiswetter and T.H. Bell, Electromagnetic induction spectroscopy for clearing landmines, IEEE trancactions of Geoscience and Remote Sensing, 39, 703-709, 2001.