Post on 17-Feb-2018
transcript
© 2016 Eaton. All Rights Reserved..
Eaton Spiral Hose and Hose Fittings –4S/6S and Product Positioning
2© 2016 Eaton. All Rights Reserved.
Product PortfolioCore Rubber Spiral Hydraulic Hose & Fittings
Premium
Premium Low Temp
Premium High Temp
Premium Abrasion
4S/6S
3© 2016 Eaton. All Rights Reserved.
4S
6S6S
(6-spiral)
4S
(4-spiral)
Simplification of the Eaton Spiral Hose Fitting Offering
4© 2016 Eaton. All Rights Reserved.
Non-brazed
Nipple
Non-brazed
Nipple
Identification
Rings
Identification
Rings
Captive NutCaptive Nut
DURA-SEAL™
Technology
DURA-SEAL™
Technology
Formed Back-up
Hex
Formed Back-up
HexNon-skive Non-skive
4S/6S Best-In-Class Technology
5© 2016 Eaton. All Rights Reserved.
Leak Free Classification – SAE J1176
Class 0 No Indication of Moisture
Class 1 Non-re-occurring Fluids
Class 2 Recurring fluid that does not result in the
formation of a droplet
Class 3 Recurring fluid that results in the formation of a
non-falling droplet
Class 4 Recurring fluid where a droplet forms and falls
Class 5 Recurring fluid where the frequency of droplets
makes a measurable stream4S/6S
DURA-SEAL
Technology
“O-ring seal”
DURA-SEAL
Technology
“O-ring seal”
4S/6S Best-In-Class Leak Free Performance
Eaton spiral hose assemblies made meet Class 0 leakage w/ 4S/6SEaton spiral hose assemblies made meet Class 0 leakage w/ 4S/6S
6© 2016 Eaton. All Rights Reserved.
TTC12430U1E/1Z
Optimized
overall
length
Optimized
overall
length
5.00
inches
5.00
inches 4.25
inches
4.25
inches
3.30
inches
3.30
inches
3.50
inches
3.50
inches
4S/6S
4S/6S Comparison to Existing Eaton Spiral Fittings
Lower hose fitting profile allows for easier hose assembly installationLower hose fitting profile allows for easier hose assembly installation
7© 2016 Eaton. All Rights Reserved.
TTC12
430Z
430U
4S/6S
Captive NutCaptive Nut Crimp NutCrimp Nut
Formed
Metric
Backup Hex
Formed
Metric
Backup Hex
Machined
Backup Hex
Machined
Backup Hex
4S/6S Design Enhancements
Formed back-up hex and captive slip over nut decreases crackingFormed back-up hex and captive slip over nut decreases cracking
8© 2016 Eaton. All Rights Reserved.
Traditional
Hose Ends 4S/6S
Braze Joint (connects elbow
to hose nipple)
Braze Joint (connects elbow
to hose nipple)
Non-brazed
elbows – elbow
and hose nipple are
one-piece
Non-brazed
elbows – elbow
and hose nipple are
one-piece
4S/6S One Piece Elbow Design
Non-brazed joints reduce the chance of field issuesNon-brazed joints reduce the chance of field issues
9© 2016 Eaton. All Rights Reserved.
“4S-20” marking on socket identifies: Hose type: 4-Spiral (4S) Hose size: -20
• 4 rings on socket refers
to 4-spiral hose (4S)
• 6 rings for 6-spiral hose (6S)
4S
-20
4S/6S Identification System
Matching hose and hose ends reduced chance of assembly errorMatching hose and hose ends reduced chance of assembly error
10© 2016 Eaton. All Rights Reserved.
4S/6S Available on www.eaton.com
© 2016 Eaton. All Rights Reserved.
Eaton Spiral Fittings
4S/6SNew Spiral Hose Fitting Family for use with 4
and 6 spiral wire hoses
Features
• Class 0 Cool Down Leakage
• Superior Corrosion Resistance
• Part of a Simplified Hose Assembly System
Primary Markets/Platforms/Applications
Value Prop
OEM
Distributor
End User
Value Proposition
• DURA-SEAL™ Technology with Class 0 leakage. Reduces
potential warranty costs (OEM).
• DURA-KOTE™ Superior Corrosion Resistance - Provides up
to 1000 hours of corrosion protection resulting in longer
life in harsh environments (End User & OEM).
• Engineered Hose Assembly System – Matches the correct
hose and hose fitting decreasing potential warranty costs
(Distributor).
• Inventory Consolidation – 4S/6S fittings are approved with
many different spiral hoses reducing inventories
(Distributor).
• Design Features Back-up Hexes and Slip Over Nuts – Allows
for easier assembly and decreases the chance for over-
torqueing resulting in rework or waste (End User and
OEM).
• Smaller Hose Fitting Profile – Allows for easier hose
installation by hose installers (OEM).
• Non-Brazed Nipples – This features reduces potential field
warranty issues (End User & OEM).
Points of Differentiation
12© 2016 Eaton. All Rights Reserved.
4S/6S Spiral Hose Fitting Availability
Sizes -12 to -32 available in May 2016Sizes -12 to -32 available in May 2016
13© 2016 Eaton. All Rights Reserved.
4S/6S End Configurations
• Male Pipe - Rigid - Straight
• Male Pipe NPTF Swivel - Straight
• Male JIC/37°- Rigid - Straight
• Female JIC/37°Swivel - Straight, 45°, 60°, 90°
• Male O-ring Boss - Rigid - Straight
• Female SAE 45°Flare Swivel - Straight
• Male ORS - Rigid - Straight
• Female ORS Swivel - Straight, 45°, 90°
• Code 61 Flange - Straight, 22.5°, 30°, 45°, 60°,67.5°, 90°, 110°
• Code 62 Flange - Straight, 22.5°, 30°, 45°, 60°, 90°
• CAT® Flange - Straight, 22.5°, 30°, 45°, 60°, 67.5°, 90°
14© 2016 Eaton. All Rights Reserved.
4S/6S End Configurations
• BSP Male Tapered - Rigid - Straight
• BSP Male Parallel - Rigid - Straight
• Female BSPP Swivel - Straight, 45°, 90°
• JIS Female Swivel - Straight
• Komatsu Female Swivel - Straight
• Female DIN DKO Swivel Light – Straight, 90°
• Male DIN DKO Heavy – Rigid - Straight
• Female DIN DKO Swivel Heavy – Straight, 45°, 90°
15© 2016 Eaton. All Rights Reserved.
NEW LEGACY
4S Part # TTC12 Part # 1E / 1Z Part # 430U Part # 470E Part # 4SP / 6SP Part #
4S20FL12 1B20FL12 - 43012U-G20 - -
4S20FL16 1B20FL16 1E20FL16 43016U-G20 - -
4S20FL20 1B20FL20 1E20FL20 43020U-G20 47020E-G20 4SP20W-G20
4S20FLA16 1B20FLA16 1E20FLA16 43016U-G50 - -
4S20FLA20 1B20FLA20 1E20FLA20 43020U-G50 47020E-G50 4SP20W-G50
4S20FLB12 1B20FLB12 - 43012U-G80 - -
4S20FLB16 1B20FLB16 1E20FLB16 43016U-G80 - -
4S20FLB20 1B20FLB20 1E20FLB20 43020U-G80 47020E-G80 4SP20W-G80
4S20FLD16 1B20FLD16 - 43016U-H04 - -
4S20FLD20 1B20FLD20 - 43020U-H04 - -
4S20FLE16 1B20FLE16 - 43016U-H64 - -
4S20FLE20 1B20FLE20 - 43020U-H64 - -
4S20FLF16 1B20FLF16 - 43016U-H24 - -
4S20FLF20 1B20FLF20 - 43020U-H24 - -
4S20FLG16 1B20FLG16 - 43016U-H54 - -
4S20FLG20 1B20FLG20 - 43020U-H54 - -
4S20JF20 1B20JF20 - - - -
4S20KF20 1B20KF20 - 43020U-36K - -
4S24FH20 1B24FH20 1E24FH20 43020U-D24 47020E-D24 4SP20W-D24
4S24FHA20 1B24FHA20 1E24FHA20 43020U-D54 47020E-D54 4SP20W-D54
4S24FHB20 1B24FHB20 1E24FHB20 43020U-D84 47020E-D84 4SP20W-D84
4S24FHF20 - - 47020E-N25 47020E-N25 -
4S24FL16 1B24FL16 - 43016U-G24 - -
4S24FL20 1B24FL20 1E24FL20 43020U-G24 - 4SP20W-G24
4S24FLA20 1B24FLA20 1E24FLA20 43020U-G54 - 4SP20W-G54
4S24FLB16.082 - - 43016U-G84 - -
4S24FLB20 1B24FLB20 1E24FLB20 43020U-G84 - 4SP20W-G84
4S24FLB20.082 1B24FLB20.070 - - - -
Cross-Reference Chart Available Through Your ASMCross-Reference Chart Available Through Your ASM
4S/6S Cross Reference Sheet
16© 2016 Eaton. All Rights Reserved.
Aeroquip 4S/6S Spiral Hose Fittings
4S/6SEaton´s high performance spiral hose fitting
design with DURA-SEAL™ technology
Class “0” Cool-Down Leakage
Superior Corrosion Resistance
Hose/Fitting Identification Program
4S/6S Eaton Aeroquip Catalog – E-HOSP-CC002-E4
17© 2016 Eaton. All Rights Reserved.
Weatherhead 4S/6S Spiral Hose Fittings
4S/6SEaton´s high performance spiral hose fitting
design with DURA-SEAL™ technology
Class “0” Cool-Down Leakage
Superior Corrosion Resistance
Hose/Fitting Identification Program
4S/6S Eaton Weatherhead Catalog – E-HOSP-BB006-E3
18© 2016 Eaton. All Rights Reserved.
• Approved Aeroquip Crimp Machines - ET1000, ET3000, ET1280, FT1380, FT1390, ET5040,
ET5050 – verify size capability by machine
• ET1280 / FT1380
• 4S-20 fitting with 4-spiral hose (ex. GH493-20) will require a new longer die for full flat
crimp in ET1280 & FT1380 machines
• ET1280 & FT1380 machines will now be capable of crimping -16 & -20 size of the
6-spiral hose (ex. FC606-16 & -20).
• 4S-20 will require die part # FT1382-200-M465 or FT1382-275-M465 (standard die)
• 6S-20 will require die part # FT1382-275-M520 (ordered separately)
• FT1390
• No new tooling is required – check your inventory to determine if you have the correct
dies
• ET5040 & ET5050 – no new Eaton tooling required
Complete Crimp and Assembly Information Available on
PowerSource
Complete Crimp and Assembly Information Available on
PowerSource
4S/6S Eaton Aeroquip Distributors – Assembly Equipment
19© 2016 Eaton. All Rights Reserved.
• Approved Weatherhead Crimp Machines – T-410, T-420, T-440, T-480, ET1000,
ET4000, ET4001, ET4020, ET4040, ET5040, ET5050 – verify size capability by
machine
• T-420 & T-480
• Requires some new collets and spacer rings depending on size and type of
hose – see catalog and PowerSource for tooling requirements
• T-410, T-440, ET4000, ET4001
• Requires some new collets and spacer rings depending on size and type of
hose – see catalog and PowerSource for tooling requirements
• ET1000
• Requires one new collet and one new spacer ring for 4S-12 fittings
• ET1000 will only crimp 4S-12; not 4S-16 with 4-spiral hose (ex. H43012 can
be crimped, but not H43016). For a similar machine with the capability of
crimping up 4-spiral -20 size hose use the T-480
4S/6S Eaton Weatherhead Distributors – Assembly Equipment
20© 2016 Eaton. All Rights Reserved.
• ET4020
• Machine is capable of crimping 4-spiral and 6-spiral hose up to -20
size
• 4S-20 will require die part # FT1382-200-M465
• 6S-20 will require die part # FT1382-275-M520
• ET4040
• No new tooling is required if you have full flat crimp dies – check
your inventory to determine if you have the correct dies
• ET5040 & ET5050
• No new tooling is required if you have full flat crimp dies – check
your inventory to determine if you have the correct dies
Complete Crimp and Assembly Information Available on
PowerSource
Complete Crimp and Assembly Information Available on
PowerSource
4S/6S Eaton Weatherhead Distributors – Assembly Equipment
21© 2016 Eaton. All Rights Reserved.
• New Tooling Packages
• ET4S-TP-001
• 4S Kit for ET1000 Machine Size -12
• ET4S-TP-002
• 4S Kit for T-420, T-480, ET3000 Sizes -12 to -20
• ET4S-TP-003
• 4S Kit for T-410, T-440, ET4001 Sizes -12 to -20
• ET6S-TP-001
• 6S Kit for ET4000, ET4001 Sizes -20 to -32
4S/6S Eaton Weatherhead Distributors – Assembly Equipment
Coming
Soon
22© 2016 Eaton. All Rights Reserved.
4S/6S TEAM Programs
• 4S/6S tooling is covered under the TEAM Program if the tooling is
intended for end user placements
• MDF Funds can be used to upgrade tooling at distributor shops.
The MDF Program would provide a 50% credit but is dependent
on the amount of funds the Distributor has earned or has
remaining. We have also allowed Distributors to use the EDP
program in the past to upgrade their capabilities that provided
them a 50% discount on a one off exception basis.
• Please contact Brian Boyle for additional details
23© 2016 Eaton. All Rights Reserved.
• List Prices Are Now Available for Catalog Part
Numbers (August 1st, 2016 Price Sheet)
• List Price Comparisons
• 4S/6S is ~ 5% less than TTC12 closest equivalents
• 4S/6S is ~ 40% less than 1E/1Z closest equivalents
• 4S/6S is ~ 40% less than 4SP/6SP closest equivalents
• 4S/6S is ~ 10% less than 430U closest equivalents
4S/6S Pricing
24© 2016 Eaton. All Rights Reserved.
4S/6S Eaton Aeroquip Core Spiral Hoses
25© 2016 Eaton. All Rights Reserved.
6S
4SGH636
4S/6S Eaton Aeroquip Core Spiral Hoses, continued
26© 2016 Eaton. All Rights Reserved.
4S/6S Eaton Weatherhead Core Spiral Hoses
27© 2016 Eaton. All Rights Reserved.
Eaton wants our channel partners to immediately convert their traditional purchases of many
single and internal skive hose fittings to their 4S/6S closest equivalents as soon as possible.
• Single Skive for FC736, FC254, FC323, FC324, GH493
• FC95xx series
• FJ97xx series
• FC96xx series
• FC59xx series
• FC97xx series
• FC98xx series
• FC99xx series
• FJ71xx series
• Internal Skive for FC273 and FC325 Hoses
• FC53xx series
• FC55xx series
• FJ97xx series
• FJ90xx series
4S/6S Eaton Aeroquip Spiral Hose Fitting Rationalization Plans
28© 2016 Eaton. All Rights Reserved.
• Internal Skive for FC254, FC323, FC324, FC736, GH493 Hoses
• FC52xx series
• FC50xx series
• FC53xx series
• FC55xx series
• FC56xx series
• FJ90xx series
• FJ96xx series
• FJ97xx series
• Included in the spreadsheet are the nipple and socket part numbers as well, if sold
separately.
• Internal Skive for FC606 Hose
• FJ72xx series
4S/6S Eaton Aeroquip Spiral Hose Fitting Rationalization Plans, continued
29© 2016 Eaton. All Rights Reserved.
Eaton wants our channel partners to immediately convert their traditional purchases of
the 470E and 570S series hose fittings to their 4S/6S closest equivalents as soon as
possible.
• The 470E and 570S series are single skive hose fittings
• With the conversion of the 4S and 6S series that provides a much stronger
value proposition, the 470E and 570S series of hose fittings will be phased
out over the upcoming months.
4S/6S Eaton Weatherhead Spiral Hose Fitting Rationalization Plans
© 2016 Eaton. All Rights Reserved..
Appendix
© 2016 Eaton. All Rights Reserved..
Spiral R12 Hoses
32© 2016 Eaton. All Rights Reserved.
Product PortfolioCore Rubber Spiral Hydraulic Hose & Fittings – R12
Use EC810
Premium
Premium Low Temp
Premium High Temp
Premium Abrasion
Standard
EC525
FC736/
H430R
GH493/
H430
33© 2016 Eaton. All Rights Reserved.
Premium Core Rubber Spiral Hydraulic Hose & Fittings
Standard Premium
Premium Low Temp
Premium High Temp
Premium Abrasion
34© 2016 Eaton. All Rights Reserved.
Premium – GH493/H430Meets or Exceeds R12
Constant Pressure
Size Pressure Size Pressure
-06 6,000 psi -20 4,000 psi
-08 6,000 psi -24 4,000 psi
-10 6,000 psi -32 4,000 psi
-12 5,000 psi
-16 5,000 psi
Premium Abrasion
Fluid Compatibility
Up to 2 million impulse
cycles
Bend RadiusMax Operating Pressure
Size Pressure Size Pressure
-06 6,500 psi -20 4,500 psi
-08 6,000 psi -24 4,000 psi
-10 6,000 psi -32 4,000 psi
-12 5,500 psi
-16 5,100 psi
Up to 1 million impulse
cycles
-40°F
+260°F
LifeSenseLifeSense
© 2016 Eaton. All Rights Reserved.
Eaton Spiral Hose
GH493 / H430 Meets or Exceeds R12 – ½ Bend
Radius
Features
• Meets or Exceeds SAE 100R12,
EN 856 Type R12, and EN 856
4SP Performance
• Higher Operating Pressure
Capability
• Higher Top End Temperature
• Premium Abrasion Resistance
Value Prop
OEM
Distributor
End User
Value Proposition
• On average Triple Crown and Diamond
Advantage hoses have a 24% higher operating
pressure, higher temperatures up to +260°F,
and better cover abrasion resistance. All of
these features provide a longer hose life
reducing potential equipment downtime and
warranty costs (End User & OEM).
• Exhibits Class 0 Cool Down Leakage per SAE
J1176 when assembled with the 4S/6S Fitting
Series. Reduces potential warranty costs
(OEM).
• The Eaton program matches the correct hose,
hose fitting and crimp tooling to be used in
making a quality hose assembly. Decreases the
chance of incorrect assembly resulting in
product that might fail in the field (End User &
Distributor).
Points of Differentiation
36© 2016 Eaton. All Rights Reserved.
Premium AbrasionCore Rubber Spiral Hydraulic Hose & Fittings
Standard Premium
Premium Low Temp
Premium High Temp
Premium Abrasion
37© 2016 Eaton. All Rights Reserved.
Premium Abrasion – FC736/H430RMeets or Exceeds R12
Max Operating Pressure
Size Pressure Size Pressure
-06 6,500 psi -20 4,500 psi
-08 6,000 psi -24 4,000 psi
-10 6,000 psi -32 4,000 psi
-12 5,500 psi
-16 5,100 psi
Ultimate Abrasion
Fluid Compatibility
500k impulse cycles
Bend Radius
LifeSense
-40°F
+250°F
700 X
Greater
½ Bend
© 2016 Eaton. All Rights Reserved.
Eaton Spiral Hose
FC736 / H430RMeets or Exceeds R12 – UHMWPE
Cover
Feature
• SAE 100R12,EN 856 Type R12
• Ultimate Cover Abrasion
Resistance
Value Prop
OEM
Distributor
End User
Value Proposition
• Exhibits Class 0 Cool Down Leakage per SAE
J1176 when assembled with the 4S/6S Fitting
Series. Reduces potential warranty costs
(OEM).
• Ultimate abrasion resistant UHMWPE cover
provides over 700 X greater abrasion resistance
than standard 100R12 hose covers. Provides
longer life in highly abrasive applications
reducing equipment downtime and warranty
claims (End User & OEM).
Points of Differentiation
39© 2016 Eaton. All Rights Reserved.
Premium High TempCore Rubber Spiral Hydraulic Hose & Fittings
Standard Premium
Premium Low Temp
Premium High Temp
Premium Abrasion
40© 2016 Eaton. All Rights Reserved.
Premium High Temp – EC525Meets or Exceeds R12
Max Operating Pressure
Size Pressure Size Pressure
-4 5,800 psi -16 2,500 psi
-6 5,000 psi -20 2,250 psi
-8 4,250 psi -24 1,750 psi
-10 3,250 psi -32 1,500 psi
-12 3,000 psi
Premium Abrasion
Fluid Compatibility
150k impulse cycles
Bend Radius
-40°F
+302°F
½ Bend
© 2016 Eaton. All Rights Reserved.
Eaton Spiral Hose
EC525 AQP PLUSMeets or Exceeds R12 – High
Temperature – ½ Bend Radius
Features
• High Temperature
• Premium Abrasion Resistance
Value Prop
OEM
Distributor
End User
Value Proposition
• Due to the highly engineered hose compounds,
this hose operates at a higher temperature
rating (up to +302°F) and exhibits a wider range
of resistance to fluids allowing a distributor to
carry less spiral hose products (Distributor).
• The highly engineered hose compounds also
provide longer life of the hose when used at
high temperatures reducing maintenance costs
(Distributor, OE, & End User).
Points of Differentiation
© 2016 Eaton. All Rights Reserved..
Spiral R13 Hoses
43© 2016 Eaton. All Rights Reserved.
Use EC810
Product PortfolioCore Rubber Spiral Hydraulic Hose & Fittings – R13
Premium
Premium Low Temp
Premium High Temp
Use EC525
Premium Abrasion
Standard FC500/
H471FC273B
44© 2016 Eaton. All Rights Reserved.
Premium Core Rubber Spiral Hydraulic Hose & Fittings
Standard Premium
Premium Low Temp
Premium High Temp
Premium Abrasion
45© 2016 Eaton. All Rights Reserved.
Premium – FC500/H471Meets or Exceeds R13
Premium Abrasion
Fluid Compatibility
Bend RadiusMax Operating Pressure
Size Pressure Size Pressure
-12 5,100 psi
-16 5,100 psi
-20 5,100 psi
-24 5,100 psi
-32 5,100 psi
500K impulse cycles
-40°F
+260°F
LifeSense
Constant Pressure
Size Pressure Size Pressure
-12 5,000 psi
-16 5,000 psi
-20 5,000 psi
-24 5,000 psi
-32 5,000 psi
500K impulse cycles
LifeSense
© 2016 Eaton. All Rights Reserved.
Eaton Spiral Hose
FC500 / H471 Meets or Exceeds R13 – ½ Bend
Radius
Features
• Flexible Hose with ½ Bend Radius
• Constant Pressure 5100 psi
• Premium Abrasion Resistance
Value Prop
OEM
Distributor
End User
Value Proposition
• A 46% improvement in force-to-bend, ½ SAE
minimum bend in sizes -12 thru -24, and 33%
reduction in bend radius for SAE100R13 -32
allows for easier installation. Allows for easier
installation of hose on equipment and less
overall hose is required reducing material costs
(OEM).
• Exhibits Class 0 Cool Down Leakage per SAE
J1176 when assembled with the 4S/6S Fitting
Series. Reduces potential warranty costs
(OEM).
• The Eaton program matches the correct hose,
hose fitting and crimp tooling to be used in
making a quality hose assembly. Decreases the
chance of incorrect assembly resulting in
product that might fail in the field (End User &
Distributor).
Points of Differentiation
47© 2016 Eaton. All Rights Reserved.
Premium AbrasionCore Rubber Spiral Hydraulic Hose & Fittings
Standard Premium
Premium Low Temp
Premium High Temp
Premium Abrasion
48© 2016 Eaton. All Rights Reserved.
Premium Abrasion – FC273BR13
Max Operating Pressure
Size Pressure Size Pressure
-12 5,100 psi
-16 5,100 psi
-20 5,100 psi
-24 5,100 psi
-32 5,100 psi
Ultimate Abrasion
Fluid Compatibility
500k impulse cycles
Bend Radius
LifeSense
-40°F
+250°F
700 X
Greater
Full
Bend
© 2016 Eaton. All Rights Reserved.
Eaton Spiral Hose
FC273BR13 – UHMWPE Cover
Feature
• Meets or Exceeds SAE 100R13, EN
856 Type R13, and ISO 3862 R13
• Ultimate Cover Abrasion
Resistance
Value Prop
OEM
Distributor
End User
Value Proposition
• Ultimate abrasion resistant UHMWPE cover
provides over 700 X greater abrasion resistance
than standard 100R13 hose covers. Provides
longer life in highly abrasive applications
reducing equipment downtime and warranty
claims (End User & OEM).
Points of Differentiation
© 2016 Eaton. All Rights Reserved..
Spiral R15 Hoses
51© 2016 Eaton. All Rights Reserved.
Product PortfolioCore Rubber Spiral Hydraulic Hose & Fittings – R15
Premium
Premium Low Temp
Standard
Premium High Temp
Premium Abrasion
EC600
EC810
52© 2016 Eaton. All Rights Reserved.
Premium Core Rubber Spiral Hydraulic Hose & Fittings
Standard Premium
Premium Low Temp
Premium High Temp
Premium Abrasion
53© 2016 Eaton. All Rights Reserved.
Premium – EC600Meets or Exceeds R15
Premium Abrasion
Fluid Compatibility
Bend RadiusMax Operating Pressure
Size Pressure Size Pressure
-12 6,100 psi
-16 6,100 psi
-20 6,100 psi
500K (4S/6S) or 1M cycles
with 1W hose fittings
-40°F
+260°F
LifeSense
Constant Pressure
Size Pressure Size Pressure
-12 6,000 psi
-16 6,000 psi
-20 6,000 psi
LifeSense
Coming
Soon
500K (4S/6S) or 1M cycles
with 1W hose fittings
© 2016 Eaton. All Rights Reserved.
Eaton Spiral Hose
EC600 X-FLEXMeets or Exceeds R15 – ½ Bend
Radius
Features
• Flexibility & ½ Bend Radius
• Premium Abrasion Resistance
Value Prop
OEM
Distributor
End User
Value Proposition
• Exhibits outstanding force-to-bend capabilities
and ½ SAE minimum bend resulting in easier
installation. Also, allows for less overall hose to
be used reducing material costs (OEM).
• Exhibits Class 0 Cool Down Leakage per SAE
J1176 when assembled with the 4S/6S Fitting
Series. Compliant with ISO 18752-DC (1W-
Fitting) for 1M impulse cycles and ISO 18752-CC
with 4S fittings. Reduces potential warranty
costs (OEM).
Points of Differentiation
55© 2016 Eaton. All Rights Reserved.
Premium Low TempCore Rubber Spiral Hydraulic Hose & Fittings
Standard Premium
Premium Low Temp
Premium High Temp
Premium Abrasion
56© 2016 Eaton. All Rights Reserved.
Premium Low Temp – EC810Meets or Exceeds R12
Max Operating Pressure
Size Pressure Size Pressure
-12 6,100 psi
-16 6,100 psi
-20 6,100 psi
-24 6,100 psi
-32 5,100 psi
Premium Abrasion
Fluid Compatibility
500k impulse cycles
Bend Radius
LifeSense
-70°F
+212°F
½ Bend
© 2016 Eaton. All Rights Reserved.
Eaton Spiral Hose
EC810 ICE CHAMPIONMeets or Exceeds R12 - ½ Bend
Radius
Features
• Features SAE 100R15 Pressures in
Most Sizes
• Low Temperature Capability of
-70°F
• Premium Abrasion Resistance
Value Prop
OEM
Distributor
End User
Value Proposition
• Allows for operation at SAE 100R15 pressures
(sizes -12 thru -24) and SAE 100R13 for -32 in
extremely low temperatures of -70°F. This
allows the use of the same hose on equipment
regardless of where it is used in the world,
decreases the chance of field warranty issues,
and decreases equipment downtime due to
failure (End User, OEM, and Distributor).
Points of Differentiation