Post on 06-Feb-2018
transcript
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Environmental & Process Monitoring instrumentation & systems
ECM for Steel / Metallurgy
ECM ECO Monitoring, a.s. Bratislava (Slovak Republic) is focal company of the ECM Group consisting from a network of subsidiaries and offices to offer an optimal technical and comercial support on field of monitoring instrumentation of gases, liquids and particles.
ECM is providing the following applications steel industry:
• Monitoring of SO2, NOX, CO, CO2, HF, TOC, O2, flow and dust to monitor stack gas and process control for
power generation, blast furnaces, steel plants, sintered plants, coke plants, cold and hot rollers and non
ferrous metal technologies
• Optimation of combustion processes
• Monitoring of low and high flow of dusty, wet and explosive gases
• Catalytic additives to keep combustion chambers clean
• Purity monitoring of O2, N2, Ar2 and other process gases
• Ambient air pollution monitoring around factories
• Waste water quality monitoring - COD, BOD, TOC, hydrocarbons, phenols, cyanides, ammonium, nitrates,
nitrides, sulfates, sulfides, conductivity, pH, DO, ORP and others
• Sound / noise / vibration monitoring
• Composition of lubrication emulsions
• „Heat stress“ monitoring
• Mill and centifuge inertion
• Particle monitoring in process and working area
• Bag filter monitoring and filtration system optimation
• Breathing mask fit testing tools
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4822 4811 E-mail: ecm@ecm.sk
Fax: +421 2 4342 7465
Process Gas Monitoring / Liquid Monitoring Systems
Examples of process monitoring applications are:
• O2 monitoring on different levels and in different media
• CO, CH4, CO2 monitoring in different gas mixtures
• He, H2, N2, Ar purity of industrial gases
• Medical gas purity
• Oil / gas industry monitoring applications
• Heat value and Wobbe index
• Claus process feed and tail gas monitoring
• TS and H2S monitoring in different media
• Sulphure in fuel
• Process chromatography
• Water in solvents
• Moisture monitoring in different media
• Semiconductor industry gas / liquid monitoring
• PVC plant gas / liquid monitoring
• Complex monitoring solutions for chlorine chemistry
• Complex monitoring solutions for nitrogen chemistry
• Air separation monitoring
ECM is providing analytic solutions for on-line monitoring of process
gases for different applications:
Combustion process control
Fast response O2 and CO monitoring systems
Industrial analysers for chemical and petrochemical applications
NDIR analysers for SO2, H2S, CO, CO2, NH3, HCl, CH4 and many other gases
H2S and Sulphure analysers for gases and gasoline
Paramagnetic oxygen analysers for different media
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4822 4811 E-mail: ecm@ecm.sk
Fax: +421 2 4342 7465
Industrial analysers for pharmaceutical industry semiconductor
industry and clean gas manufacturers
O2, SO2, NO, CO, CO2, CH4 multicomponent analysers
Multicomponent FTIR analysers for broad range of compounds
Accurate oxygen analysers
Physical property: Dew point, Cloud point, Flash point,
Distilation point, etc. analyzers
Hydrogen analyzers
Biogas monitoring
CO, CH4, CO2, H2S analytic systems
Analysers for cement kiln control
CO,CO2, O2, NO monitoring for high temperature and dusty
atmosphere
Claus process tail gas monitoring
H2S/SO2 monitoring in the high sulphur content Claus process tail gas
atmosphere
Analysers for food industry:
O2, CO2 analysers for package gases
CO2 purity analysers for beverage manufactures
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Process gas chromatographs
The instruments are to monitor different gaseous compounds, which can be not
measured by sampler methods
Analysers for clean gas manufacturers
Analysers for cleaners and trace level monitoring of Ar 2, O2, N2
and other gases
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Oxygen monitoring
Flue gas
• Tuneable laser O2 / CO analyzers for large boilers
• Zirconia and catalytic CO
Main adventages:
• Yearly calibration interval
• Same analyser for 150°C - 1500°C temperature range
• Combination of laser and Zirconia probes allows safe detection of areas with excess or lack of
oxygen in combustion process
• Our laser monitors allow to use air purge instead of usual nitrogen to keep the optics clean
Process gases
Broad range of paramagnetic, zirconia, optical or electrochemical analyzers from trace
concentrations up to oxygen purity monitoring around 100% O2 concentration.
The main applications are:
• Clean industrial gas production
• Oxigen content in different process gas mixtures
• Inertization processes
• Working area safety
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Metals - steel mini mills The metals industry is a core focus for PCME’s business, with extensive experience in integrated steel mills, foundries, aluminium smelters and steel mini mills driving the continuous development of monitoring solutions to best meet the demands of industry. Experience gained from over 5,000 applications in the metals industry alone gives PCME a comprehensive understanding of the potential issues facing particulate monitoring for steel mini mills, in particular: High temperature flue gases and high ambient temperatures create demanding conditions for both sensors and baghouses, increasing the need for responsive and predictive bagfilter monitoring capability due to environmental stress on bagfilter media Harsh and dusty environments require dependable and rugged sensor operation, where reduced sensor maintenance requirements, reduced sensitivity to sensor contamination, and a range of durable sensor options for challenging stack conditions are of significant benefit to plant operators. PCME offer approved (TUV & MCERTS) systems for particulate measurement, filter leak monitoring and filter performance monitoring, depending on the plant specific requirements which are specified in close consultation between plant operators and PCME. Steel Mini Mill plant typically demands monitoring on multiple emission points across furnace, casting and rolling mill operations, which can be addressed with a networked multichannel system. By offering a range of measurement technologies in reliable and rugged instruments, PCME are able to offer a full range of solutions to meet and often exceed legislative compliance, and significantly improve the operation of filter plant including a reduction in filter maintenance requirements. As knowledge and awareness increase in the environmental and health concerns associated with metallic particulates, regulators are increasingly focusing on operators of metals plant to enforce lower emissions limits and more strict compliance programs. With a history of establishing, developing and maintaining strong partnerships within the metals industry, PCME bring extensive experience for assisting plant operators to both minimise emissions and improve the operation of filter plant.
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Stack Gas Emission Monitoring
Environmental & Process Monitoring instrumentation & systems
Calorific Value Analyzers
Calorific value analysers are to monitor natural gas, petrochemical waste
gases, coke gas, blast furnace top gas, biogas .....
ECM is offering several solutions:
Miniature gas chromatographs for analysis of gas compositions and caloric
value of natural gas. An accurate instrument optimized for any natural gas
related application.
Catalytic oxidation based analyzers to monitor Wobbe index or calorific value of
flammable and even on flammable gases.
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4822 4811 E-mail: ecm@ecm.sk
http:// www.ecomonitoring.com Fax: +421 2 4342 7465
Promecon Power Generation Optimalization Systems
The Promecon systems allow significant optimization of the thermal processes such as coal fired boilers,
smelter processes, cement kilns and others. Using innovative technologies emissions are reduced,
efficiency and availability of plants are entranced.
The Promecon optimization system is utilizing several innovative sensor products:
• Cross correlation based combustion air flow sensors working
reliably in harshest conditions for up to 40m/s flow speed and up
to 1100°C temperature.
- No calibration needed
- No drift, no cleaning
- Not affected by high dust
• SIL2 available coal mass flow/velocity/particle size measurement
- Long life ceramic sensors
50-10 000 g/m3 concentration
0-100 t/hr mass flow
10-60 m/s velocity
30-60 um particle size
- Different probe length, ATEX
• Fast responding temperature sensor on mill classifiers without abrasion.
• Online unburned carbon measurement.
This is the World most sold fly ash analyzer.
- Lab accuracy in process
0-20% carbon in fly ash
2-10 minutes measuring cycle
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4822 4811 E-mail: ecm@ecm.sk
http:// www.ecomonitoring.com Fax: +421 2 4342 7465
System Application for Boiler Optimization
� PROMECON is a total solution provider for Boiler optimization.
� Patented, unique online measurement systems for PF/ Biomass, PA, SA, OFA, particle size distribution,
carbon in fly ash and other parameters.
� Evaluation of pulverizer, coal pipes, air ducts, boiler, APH.
� Improved control concepts for increased load gradient, low load operation, multifuel burning etc.
� Our references are our (PROMECON) references. Installed basis > 2000 sensors.
� All designed and made in Germany.
� Tuning through measurement and control (APC).
� We handle complete projects, CFD, modification of ductwork, trimming dampers, optimization.
� Typical projects: Plant assessment, Efficiency testing, Boiler optimization, Advanced process control.
� Field of projects: Pulverizer, coal/air distribution, combustion, fluegas.
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4822 4811 E-mail: ecm@ecm.sk
http:// www.ecomonitoring.com Fax: +421 2 4342 7465
Combustion Control System
System for controlling and optimizing high temperature processes. FlameSight combines
video technology with emissions spectroscopy. The PC based system interprets flames and
optimizes their performance online through the system software.
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovenská republika
Tel.: +421 2 4342 9418 E-mail: ecm@ecm.sk IČO: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com IČ DPH.: SK2020317244
Fax: +421 2 4342 7465
Controlling and monitoring of gas and oil burners of any capacity.
Optionally with integrated flame monitor and adjustable treshold.
Optionally with adjustable propagation time. Connection of UV, IR
and UV/IR or ionisation flame sensors.
Environmental & Process Monitoring instrumentation & systems
Termographic systems
Thermographic camera systems to monitor temperature distribution in combustion chambers to
maintain the “fire ball” in a central position to avoid vicinity to the walls resulting in cracking of
tubes and membranes. The cameras are cooled and automatically refractive.
Thermographic systems to monitor rotation cement kilns and drying processes.
Environmental & Process Monitoring instrumentation & systems
Flame detectors and ignitors
Flame detectors and ignitors for various fuels and combustion chambers
Environmental & Process Monitoring instrumentation & systems
Oil in water analyzers
Since oil in water means a broad range of water pollutant in terms of chemical
composition, concentration, phase and other characteristics, so are also the
appropriate analytic methods.
ECM is offering application specific fluorescent, chromatographic, extractive and spectrometric
analyzers to monitor all kinds of hydrocarbons in water in broad range of concentrations.
Typical applications are:
• Waste water systems in oil / gas industry
• Chemistry and petrochemistry
• Drinking water treatment
• Steel industry and metallurgy
• Truck / train washing yards
• Airports
• Oil in condensate and cooling water
• Power generation
Environmental & Process Monitoring instrumentation & systems
Gas purity / trace pollution
ECM is designing and supplying analyzer systems for quality control of industrial gases integrating
gas purity analyzers of the worldwide market leader – the company Servomex as well.
We offer solutions vary from single portable or desk top systems, via analyzer cabinets for quality
control of medical gases according to Pharmacopeia, up to complex gas analyzer systems for
process control and optimization of the operation of Air Separation Units.
ECM Group became a recognised partner and supplier of gas analyzer systems to the market
leaders of the gas industry. The market leaders which are listed below are among our clients:
−
−
−
Messer Group
Air Liquide
Linde Gas
SOL Group
HR, RS, BA, BG, MK, SI, CZ, SK, H
AT, BG, CZ, SK, H
BG, GR
−
−
−
PRAXAIR (Istrabenz Plini)
Air Products (Sapio Plini)
SIAD
SI
SI, CZ
CZ
Environmental & Process Monitoring instrumentation & systems
Environmental & Process Monitoring instrumentation & systems
Water quality samplers
Environmental & Process Monitoring instrumentation & systems
Spectrometric Water Quality Monitors
This unique submergible instrument allows continuous monitoring of
nitrates, organic compounds, turbidity, colour and many other
features of monitored water. The organic pollutants may be
monitored as specific compounds (for instance benzene, toluene,
gasoline, diesel oil, etc.), or as general charakteristics like TOC, COD,
BOD, hydrocarbons in water. It allows portable, stationary or battery
powered long term logging applications with instant response time.
Multisubstance measurements with one single instrument; high
resolution UV-Vis spectra allow selective distinction between many
substances.
2-beam-measurement ensures constant measuring quality over long
periods of time with virtually no instrument shift.
Intelligent spectral compensation provides:
superior turbidity correction considering the character of turbidity
superior identification and correction of long time effects like biomass
growth on windows
"Spectral Fingerprinting" - approach allows definition of sensitive,
accurate, reliable alarm and early warning parameters.
Full field compatibility: no installation, plumbing and interconnect ion
problems in the f ie ld ; l ow energy consumption at 12 V; robust
design.
Better overall accuracy and security: reduction of the "Total Error of
Measurement" no sampling-, transport-, handling-, storage-, counting-,
diluting-, etc. mistakes, no mixing up of samples.
Additional probes or autosamplers are often unnecessary;
much higher flexibility in the field.
Autonomy features: internal buffered data logger; energy autarkic; self
testing and alarm routines; networking capability; integrated hydraulic
cleaning nozzles optional (for high solids contents).
Environmental & Process Monitoring instrumentation & systems
Parameters can be measured simultaneously, in-stream, with one method
and one completely autonomous instrument, on- site or remote
controlled, even many instruments in a network.
A new level of stability, effectiveness, and time resolution can be
reached, and, as a result, a surprising gain of additional information
about water related processes.
High energy optical performance enables measurements in
even in fluids with high optical density like oil mixtures, milk or
coffee, often down to the deep UV, far superior to fiber optic
instruments with respect to energy and process stability.
spectral range: 190 nm to 380 nm or 190 nm to 780 nm
light sources: regulated Xenon lamp
long term stability: virtually no instrument shift of auto
c o m p e n s a t i o n b a s e d o n 2 b e a m m e a s u r e m e n t
optical range:optical pathlengths from 2 to 100 mm (longer paths up to
200 mm on demand)
By-Pass fittings for easy installation in by-passing streams.
standard interfaces on board: RS 232 or 485
optional: CAN bus or other bus standards; via control terminal: TCP/IP,
GSM or analog modem; 4-20 mA or any PC104 bus interface
battery buffered data logger
for 1000 spectra or many
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Environmental & Process Monitoring instrumentation & systems
10.000’s of concentration values
internal temperature and moisture measurement standard;
external pressure sensor (water depth) optional: 0-0,1 bar; or
0-1 bar ( others on demand )
analysers are resistant against impacts of most natural and waste
waters.
energy:
12 V external; average 300 mA during measurements; 1 A
supply necessary
sleep mode option in data logger modus reduces
consumption to 5 mA inbetween measurements
internal battery for independent measurements optional
Gas mask fitting monitor
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Environmental & Process Monitoring instrumentation & systems
Noise & Vibration
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Environmental & Process Monitoring instrumentation & systems
Toxic and combustible gas detectors
Broad range of stationary and portable toxic and flammable gas detectors. The instruments can be
provided with a wireless transmission with a several kilometres range.
Instrumentation allowing to set up in few seconds an accident site. The emergency team control has a
permanent information about the risks the members are exposed to. Stationary systems can be installed in
few minutes without any need of obstaculous cable connections.
Higher category of the instrumentation allows reliable detection of almost all kinds of hazardous
gases.
• Personal monitors
• Site survey instrumentation
• Portable instruments
• Fixed instruments
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Environmental & Process Monitoring instrumentation & systems
• Wireless infrastructure
• Software
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Oil in water analyzers
Since oil in water means a broad range of water pollutant in terms of chemical composition,
concentration, phase and other characteristics, so are also the appropriate analytic
methods.
ECM is offering application specific fluorescent, chromatographic, extractive and spectrometric
analyzers to monitor all kinds of hydrocarbons in water in broad range of concentrations.
Typical applications are:
• Waste water systems in oil / gas industry
• Chemistry and petrochemistry
• Drinking water treatment
• Steel industry and metallurgy
• Truck / train washing yards
• Airports
• Oil in condensate and cooling water
• Power generation
Environmental & Process Monitoring instrumentation & systems
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic Phone: +421 2 4342 9418 E-mail: ecm@ecm.sk Company Reg. No.: 17312094
+421 2 4342 7408 http:// www.ecomonitoring.com VAT No.: SK2020317244
Fax: +421 2 4342 7465
Ambient Air Monitoring Systems ECM ambient air monitoring systems are integrated in air conditioned thermal isolated light
weight shelters allowing stationary and mobile installations.
The usually monitored gaseous pollutants are:
� SO2 � H2S � CxHy
� NOx � TRS � PAH
� O3 � NH3 � HF
� CO � VOC
Automated Ambient Air Mercury Analyzer
Long-term mercury analysis with unmatched accuracy, sensitivity, and reliability.
Key features:
• Low detection limit < 0.1 ng/m3
• Internal permeation source for automated calibrations
• Dual channel gold trapping for uninterrupted sampling
• Low operation costs
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4828 7261 +421 2 4342 7408
E-mail: ecm@ecm.sk http:// www.ecomonitoring.com
Company Reg. No.: 17312094
VAT No.: SK2020317244
Fax: +421 2 4342 7465
Environmental & Process Monitoring instrumentation & systems
Aerosols are monitored in accordance to TSP, PM10, PM2,5 or PM1 standards. Simultaneous monitoring
and sampling of different fractions.
Certified dual channel beta gauge particle monitor coupled to a
certified sampler and an 8 channel OPC with continuous reading of
aerosol concentrations.
Sampler products allow to take aerosol sample or later analysis for heavy metals and other pollutants.
RackMount Model AE22
The Aethalometer TM is the world leading method of measuring black carbon (BC) or elemental
carbon (EC) particles in air.
The Aethalometer is an instrument that uses a continuous filtration and optical transmission technique
to measure the concentration of BC in near-real-time.
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4828 7261
+421 2 4342 7408
E-mail: ecm@ecm.sk
http:// www.ecomonitoring.com Company Reg. No.: 17312094
VAT No.: SK2020317244
Fax: +421 2 4342 7465
Environmental & Process Monitoring instrumentation & systems
The only commercially available field deployable OC/EC analyzer with true laser-based pyrolysis
correction and compatibility with accepted NIOSH 5040 methods.
Ultrafine particle monitor TSI
Provides continuous Ultra-fine Particle (UFP) size distribution and number concentration data for
long-term, air quality monitoring.
Features and Benefits:
• Long-term, unattended operation
• Size distribution from 20nm – 1,000 nm
• Low start-up and operating costs
• No working fluids; radioactive source
• Convenient data management with remote access via the Internet
• Continuous measurements
• Optional environmental sampling system
Compact TSP, PM10, PM4, PM2,5 PM1 instrument to monitor all of the fractions in parallel.
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4828 7261 +421 2 4342 7408
E-mail: ecm@ecm.sk http:// www.ecomonitoring.com
Company Reg. No.: 17312094
VAT No.: SK2020317244
Fax: +421 2 4342 7465
Environmental & Process Monitoring instrumentation & systems
Particle counter / sizer allowing to define 16 size channels showing particle count and mass
concentration both.
Optical Particle Sizer 3330
Product Details
Optical Particle Sizer 3330 (OPS) is a light, portable unit that provides fast and accurate measurement of
particle concentration and particle size distribution using single particle counting technology. Backed by
over 40 years of aerosol instrumentation design experience, the OPS uses state-of-the-art optics with
120° light collection and sophisticated electronics processing resulting in precision, high quality data.
Rigorous factory calibration standards ensure measurement accuracy. The Model 3330 particle sizers can
be used alone, or it can be placed in TSI’s weatherproof Environmental Enclosure.
Online monitoring of heavy metals in ambient dust
ECM ECO Monitoring, a.s., Nevädzová 5, 821 01 Bratislava, Slovak Republic
Phone: +421 2 4828 7261 +421 2 4342 7408
E-mail: ecm@ecm.sk http:// www.ecomonitoring.com
Company Reg. No.: 17312094
VAT No.: SK2020317244
Fax: +421 2 4342 7465
Environmental & Process Monitoring instrumentation & systems
Compact ambient air monitoring station SO2, NOx, NO2, O3, CO, CO2, VOC, PM10/ 2,5/1
Auto Handler for Dust Filter Weighing
Complete solution coupling Filter Weighing System with weighing automation. The unit and weighs each
filter according to administrator selected instructions. Each filter's bar code is read. It is then taken to the
balance where it is inserted and placed on the balance pan in the exact came position each time
Weighing time: 3 min per filter using direct read. AH225 performs automated static discharge.