Post on 28-Sep-2015
description
transcript
Operators Manual
SINGLE JOINT ELEVATOR
o mruOilfield TechnologiesOilfield Technologies
English
(SMALL & LARGE FRAME)
Rev. G 11-14-06
To reduce the risk of injury, everyone using,
installing, performing maintenance, changing
accessories on, or working near this tool must
read and understand these instructions before
performing any such task.
WARNING
26-999-031
SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS
SINGLE JOINT ELEVATOR
For Additional Safety
Information Consult
Your employer, union, or trade association.
US Department of Labor (OSHA)
or Council of European
Communities
Contact at
at
www.osha.gov
www.europe.osha.eu.int
Do not use oversized pipe. Using oversized
pipe could cause difficulties in the proper
latching of the elevator.
Do not use undersized pipe. Using
undersized pipe could cause uneven stress
distribution, inadequate load bearing area,
and a possible collar slippage through the
elevator.
Do not use the elevator if the Latch or Latch-
Lock is malfunctioning. Latch or Latch Lock
failure could cause injury.
Do not overload the elevator. Overloading
the recommended rating could cause
serious injury or death.
Secure the Retainer Pin when using the
elevator in a non-horizontal position. Failure
to secure the Pin when picking up or laying
down pipe could cause serious injury or
death.
Use square shoulder connections with
tubular collars when handling pipe. Failure
to use the proper connections could cause
injury.
Position the Safety Latch Pin prior to hoisting
pipe. Failure to use the proper connections
could cause injury.
Maintain proper shoulder width on the pipe.
Failure to maintain ample shoulder widths
could cause injury.
Use the proper size pipe for the elevator
bore. Failure to use the proper size pipe
could cause injury.
To prevent injury or elevator malfunction,
inspect the Bore, Latch, Latch Pin, and
Hinge Pin regularly for wear. Failure to
inspect these parts could cause injury.
Keep hands / fingers clear of elevator bore
when installing the elevator on the pipe.
Always use the proper tools and wear eye,
head, and hand protection when servicing
this elevator.
Maintain a balanced body position and
secure footing.
For professional use only.
Use only Access Oil Tools, LP (AOT) parts.
AOT equipment is made of cast ally heat
treated steel and should never be welded on
in the field. Improper welding can cause
cracks or brittleness in the casting which
could result in drastic weakening or failure of
the equipment. Any welding or machining
must be performed by an authorized AOT or
API Certified Repair Center.
Improper welding and / or re-machining of
cast alloy heat treated steel can cause
personal injury, property damage, or death.
Operating Hazards
Workplace Hazards
Maintenance Hazards
o mruOilfield Technologies
DO NOT DISCARD - GIVE TO USER 2
Rev. G 11-14-06
To reduce the risk of injury, everyone using,
installing, performing maintenance, changing
accessories on, or working near this tool must
read and understand these instructions before
performing any such task.
WARNING
26-999-031
The goal of the ACCESS OIL TOOLS, LP is to produce tools that help you
work safely and efficiently. The most important safety device for this tool is
YOU. Your good judgment is the best protection against injury.
Table of Contents
o mruOilfield Technologies
3
2 SAFETY INSTRUCTIONS - Single Joint Elevator
4 1.0 Introduction
5
4
4
Replacement Parts - Single Joint Elevator (Large Frame)
Figure 4 - Locations of Tool Maintenance items
Figure 5 - Critical Areas
Replacement Parts - Single Joint Elevator (Small Frame)
4.0 Repair
Replacement Parts - Single Joint Elevator (Small Frame)
8
6
9
7
5
6
10 Manufacturers Limited Warranty
4 2.0 Operation
5 3.0 Maintenance
Figure 3 - Tool Maintenance Chart
Figure 1 - Model Specifications
Figure 2 - Warning Label
Rev. G 11-14-06
The equipment represented in this manual is European Community (EC) compliant with the
below listed Directives and Harmonized Standards. For an additional cost, EC certification can
be obtained for any of the equipment herein. Contact an AOT Sales Representative for cost
information. Certification requests must be stated on a purchase order.
Directive 98/37/EEC - EC Machinery Directive
En292, Safety of machinery - basic concepts, general principles for design
1.0 Introduction
This manual contains operation and maintenance
instructions for the ACCESS OIL TOOLS, LP (AOT)
SJ series single joint center latch pick up elevator
and provides guidance for its proper field use,
disassembly and repair; including a complete parts
breakdown.
SJ elevators are designed to replace rope slings for
hoisting collar type pipe into position and added to a
string. SJ elevators allow the crew to handle pipe
properly, thus avoiding pipe thread damage and
reduces the chances of accidents / injuries.
The SJ series center latch pick up elevator has a
simple, reliable latch that closes simultaneously
when elevator is closed. To ensure the Latch does
not open, a Latch Lock Pin can be used as a safety
feature. The size range of the SJ series elevator is
as illustrated in the table provided.
(See Figure 1)
o mruOilfield Technologies
4
2.0 Operation
As with any manual operated elevator, the SJ is
easily installed by the use of swivel suspension
assembly. Perform the actions prescribed below
after the elevator is hoisted to the rig floor and
properly positioned.
The operation of the SJ elevator is straightforward.
The door is opened by removing the Safety Latch
Pin and pulling outward on the Latch. When the
elevator is properly closed around the pipe, install
the Latch Lock Pin.
(See Figure 4)Remove the bolt from the shackle on the swivel
suspension assembly.
Attach the shackle over the lifting eye on the
elevator then replace the bolt to the shackle.
Repeat the process for the opposite lifting
eye. To remove the elevator, simply reverse
the process.
Rev. G 11-14-06
NOTE: WARNING labels have been installed at
critical areas on the tool. Familiarize yourself with
their message and locations before proceeding to
operate equipment.
See Figure 2.
NOTE: Use a collar type pipe weighing 5-Short Tons
(4.54 metric tons) or less.
Figure 2
ModelShortTon
MetricTonnes
Range
SJ 5 4.54 2-3/8- 24-1/2
Figure 1
WARNING
Beware of
Hand Placement.
Pinch Point.26-999-006
o mruOilfield Technologies
5
3.0 Maintenance
To ensure optimum performance, perform the
below-listed weekly checks.
Lubricate the elevator regularly during usage and
storage to prevent corrosion. Use an extreme
pressure, multi-purpose, lithium base grease of No.
1 or No. 2 consistency or a lubricant that meets MIL-
SPEC-A907E.
Maintain elevator as prescribed in the below
periodic Actions / Examinations.
(See Figure 3)
Locations of parts identified in Figure 1 have been
illustrated below for reference.
(See Figure 4)Check for worn Hinge Pin and Latch Pin and their
mating parts. These, if worn, may hinder proper
opening and closing of the door and latch.
Check the Latch Retaining Pin assembly for
worn or damaged parts. (e.g., Safety Latch Pin).
Check for proper Latch Spring performance.
Check for proper operation of Latch Stop
mechanism. Latch should not stop against the
body when engaged.
Check springs for damage, deformation and lack
of tension.
Tool Maintenance
Grease Hinge Pin
Load Test
Daily
4
-
4
4
Lubricate Latch
Lock Pin
Grease Bore and
Seating Surface
Magnetic Particle
Examination**Every 6 Months
Yearly
4
4
5
Lubricate Latch
Pin
Grease underside
of Lifting Eye
ACTION FREQUENCY FIG.
Figure 3
** Magnetic particle examinations should be on the
critical areas only.
Rev. G 11-14-06
Maintenance Item
Locations
Figure 4
Hinge Pin
Latch Lock
PinLatch Pin
Lifting
Eye
Bore and
Seating Surface
o mruOilfield Technologies
6
4.0 Repair
We have identified those areas considered critical
to tool performance and functionality. These should
be examined for repair or replacement.
(See Figure 5)
Critical
Areas
Figure 5
The SJ series elevator requires minimum attention.
Replace the Hinge Pin, Hinge Pin Retainer Pin,
Latch Pin, and Safety Latch Pin as prescribed
below.
To remove the Hinge Pin, first remove the Hinge
Pin Retainer Pin. Drive out the Hinge pin from
the bottom of the elevator. Replace the Hinge
Pin and Hinge Pin Retainer Pin.
To remove the Latch Pin, first remove the Latch
Pin Retainer Pin. Drive out the Latch Pin from the
bottom of the elevator. Replace the Latch Pin,
Latch Pin Spring, and Latch Retainer Pin.
To remove Latch Safety Pin, remove the bolt on
the elevator door.
NOTE 1: Bodies and doors are specifically matched
by trained Access Oil Tools, LP professionals. For
this reason, a body or door from one elevator should
never be exchanged with a body or door from
another elevator.
NOTE 2: Pins retained by riveting or peening must
be well secured by upsetting a substantial amount
of material on the pin or mating parts.
Rev. G 11-14-06
o mruOilfield Technologies
7
Replacement Parts
Description
2 3/8 - 20 Latch Spring
2 3/8 - 13 3/8 HINGE PIN
GREASE ZERT
2 3/8 - 13 3/8 Latch
2 3/8 - 20 Latch Pin
2 3/8 - 20 HINGE PIN RETAINING PIN
NAMEPLATE - SINGLE JOINT ELEVATOR (if EC certified)
WARNING - PINCH POINT LABEL
2 3/8 - 20 Latch RETAINER PIN ASSEMBLY
Item
Part Series
Qty. Part No.
11 E39-034
E39-043-XXX-EC
1
1
5
7
E39-052
PGZ.250
12 E39-035
13 E39-050
2
1
1
6
8
9
E39-055
26-999-033
26-999-008
14 E39-051
Single Joint Elevator(Large Frame)
Rev. G 11-14-06
READ / WARNING LABEL110 26-999-031
2
5
4
3
1
7
10
8
6
9
o mruOilfield Technologies
8
Replacement Parts
Part Series
E39-039-XXX-EC
E39-040-XXX-EC
E39-041-XXX-EC
E39-042-XXX-EC
Description
2 3/8 - 20 LATCH SPRING
14 - 20 HINGE PIN
2 3/8 - 20 LATCH PIN
2 3/8 - 20 LATCH RETAINER PIN ASSEMBLY
2 3/8 - 20 HINGE PIN RETAINING PIN
14 - 20 LATCH
Item Qty. Part No.
11 E39-034
15 E39-053
12 E39-035
13 E39-050
26 E39-055
14 E39-054
Rev. G 11-14-06
GREASE ZERT
NAMEPLATE - SINGLE JOINT ELEVATOR (if EC certified)
WARNING - PINCH POINT LABEL
READ / WARNING LABEL
17 PGZ.250
1
1
1
8
9
10
26-999-033
26-999-008
26-999-031
Single Joint Elevator(Small Frame)
2
5
4
3
1
7
10
8
6
9
o mruOilfield Technologies
9
Replacement Parts
Description
LATCH SPRING
HINGE PIN
LATCH
LATCH PIN
3/16 X 2 Roll Pin
LATCH LOCK PIN
Item Qty. Part No.
1 1 E39-197
5 1 E39-199
2 1 E39-190
3 1 E39-198
6 1 PR .187x2
4 1 E39-196
Part Series
E39-200-XXX-EC
E39-210-XXX-EC
Rev. G 11-14-06
GREASE ZERT
NAMEPLATE - SINGLE JOINT ELEVATOR (if EC certified)
WARNING - PINCH POINT LABEL
17 PGZ.250
1
1
8
9
26-999-033
26-999-008
READ / WARNING LABEL110 26-999-031
2
34
5
7
6
1
Single Joint Elevator(Small Frame)
7
8
8
o mruOilfield TechnologiesOilfield Technologies
For more information, please contact us at:
Access Oil Tools, LP3711 Melancon RoadBroussard, LA 70518
www.AccessOilTools.com
Tel: 337.367.5044
Toll Free: 800.832.7349
Fax: 337.367.0795
Manufacturers Limited Warranty
Products manufactured by ACCESS OIL TOOLS, LP
(AOT) are warranted to be free from defects in
material and workmanship for one year from the date
of delivery. This warranty applies only to products
purchased new from AOT or its authorized dealers.
Of course, this warranty does not apply to products
which have been abused, misused, modified, or
replaced by someone other than AOT or its authorized
service representatives. AOT will not assume
responsibility or liability for any repairs, rebuilding,
welding, or heat treatment done to its products outside
of its facilities. All AOT products are manufactured /
final assembled, as necessary, for both safety and
operational performance. The omission of product
components may result in a malfunction and
consequent safety hazard for which AOT disclaims
any responsibility or liability for injuries or damage as
a result thereof. If an AOT product proves defective
in material or workmanship within one year of
delivery, contact AOT customer service to obtain a
Return Authorization (RA) number and return the
product to the AOT facility in Broussard, Louisiana or
an alternate facility as directed by AOT. All freight
charges for product returns / re-shipment shall be paid
by the customer.AOT will determine the cause for the
return and, at its option, repair or replace defective
products free of charge. Product repairs /
replacements are warranted as described above for the
remainder of the original warranty period. (There
are no other warranties expressed or implied and
AOT shall not be liable for incidental,
consequential, or special damages or any other
damages, costs or expenses excepting only the cost
and expense of repair / replacement as described
above.)
In the case of goods or parts not manufactured wholly
by AOT, AOT will make available to the customer
whatever supplier warranty / guaranty is extended to
AOT for such goods / parts.
Access Oil Tools, LP - All rights reserved.
Access Oil Tools is a division of Forum Oilfield Technologies
Product manufactured in USA
Rev. G 11-14-06
Page 1Page 2Page 3Page 4Page 5Page 6Page 7Page 8Page 9Page 10