Post on 20-Jan-2016
transcript
ICS 77.140.80; 77.150.99
Descriptors: Liquid penetrant inspection, castings, testing.
Gießereiwesen – Eindringprüfung – Teil 1: Sand-, Schwerkraftkokillen- und Niederdruckkokillengußstücke
European Standard EN 1371-1 : 1997 has the status of a DIN Standard.
A comma is used as the decimal marker.
National forewordThis standard has been prepared by CEN/TC 190.The responsible German body involved in its preparation was the Normenausschuß Gießereiwesen (FoundryStandards Committee), Technical Committee Oberflächenprüfung.
Ref. No. DIN EN 1371-1 : 1997-10English price group 13 Sales No. 1113
04.98
DEUTSCHE NORM October 1997
EN 1371-1{
EN comprises 23 pages.
© No part of this standard may be reproduced without the prior permission ofDIN Deutsches Institut für Normung e.V., Berlin.Beuth Verlag GmbH, D-10772 Berlin, has the exclusive right of sale for German Standards (DIN-Normen).
Founding – Liquid penetrant inspectionPart 1: Sand, gravity die and low pressure die castings
English version of DIN EN 1371-1
English version
ICS 77.140.80; 77.150.99
Descriptors: Liquid penetrant inspection, castings, testing.
Founding – Liquid penetrant inspectionPart 1: Sand, gravity die and low pressure die castings
© 1997. CEN – All rights of exploitation in any form and by any meansreserved worldwide for CEN national members.
Ref. No. EN 1371-1 : 1997 E
Gießereiwesen – Eindringprüfung –Teil 1: Sand-, Schwerkraftkokillen-und Niederdruckkokillengußstücke
This European Standard was approved by CEN on 1997-06-02.CEN members are bound to comply with the CEN/CENELEC Internal Regulationswhich stipulate the conditions for giving this European Standard the status of anational standard without any alteration.Up-to-date lists and bibliographical references concerning such national stand-ards may be obtained on application to the Central Secretariat or to any CENmember.The European Standards exist in three official versions (English, French, German).A version in any other language made by translation under the responsibility of aCEN member into its own language and notified to the Central Secretariat has thesame status as the official versions.CEN members are the national standards bodies of Austria, Belgium, the CzechRepublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland,and the United Kingdom.
EN 1371-1
June 1997
Central Secretariat: rue de Stassart 36, B-1050 Brussels
European Committee for StandardizationComité Européen de NormalisationEuropäisches Komitee für Normung
|ÈÉË
Fonderie – Contrôle par ressuage –Partie 1: Pièces moulées au sable, encoquille, par gravité et basse pression
Figure C.2: Severity level SP 2 – CP 2
Figure C.3: Severity level SP 3 – CP 3
Page 16EN 1371-1 : 1997
Figure D.2: Severity level LP 1b – AP 1b [LP 2a*) – AP 2a*)]
Figure D.3: Severity level LP 1c – AP 1c [LP 2b*) – AP 2b*) or LP 3a*) – AP 3a*)]
*) Approximately comparable at these severity levels
Page 18EN 1371-1 : 1997
Figure D.4: Severity level LP 2c – AP 2c [LP 3b*) – AP 3b*) or LP 4a*) – AP 4a*)]
Figure D.5: Severity level LP 3c – AP 3c [LP 4b*) – AP 4b*) or LP 5a*) – AP 5a*)]
*) Approximately comparable at these severity levels
Page 19EN 1371-1 : 1997
Page 20EN 1371-1 : 1997
Figure D.6: Severity level LP 4c – AP 4c [LP 5b*) – AP 5b*)]
Figure D.7: Severity level LP 5c – AP 5c
*) Approximately comparable at these severity levels