Post on 24-Aug-2020
transcript
Graphics Portfolio
Hyung-Jin (Hunter)
EVDS Graphics One
Assignment 1Orthographic ProjectionsPart 1
Assignment 2Orthographic ProjectionsPart 2
Assignment 3MappingPart 1
Station Selection Data Selection Data Recording
Data Analysis
8:00
12:00
17:00
Data Representation
8:00 12:00 17:00
Data Animation
PLATFORM
McKnight - Westwinds
Whitehorn
Rundle
Marlborough
Victoria Park / Stampede
39th Avenue
Anderson
Fish Creek - Lacombe
Somerset - Bridlewood
Shawnessy
Canyon Meadows
Southland
Chinook
Erlton / Stampede
Crowfoot
Dalhousie
University Banff Trail
Sunnyside
SAIT / ACAD / Jubilee
City Hall
Centre Street
1st Street SW
3rd Street SW6th Street SW8th Street SW
Franklin
Barlow / Max Bell
Calgary Zoo
Bridgeland /Memorial
4th Street SW7th Street SW
Heritage
Brentwood
Martindale
Saddletowne
CTrain Map
69th Street
Sirocco
45th Street
Westbrook
ShaganappiPoint Sunalta
DowntownWest / Kerby
Tuscany
Lions Park
300
300
100
unnyside
SAIT / ACAD / Jubilee
36th Street SW8th Street SW
4th Street S7th Street SW
wntownt / Kerby
300
8th Street SW
-Downtown-Two Trains-Fare Free Zone
University Banff Trail
Sunnyside
SAIT / ACAD / Jub
8th Street SW
7th St
Street
rook
ShaganappiPoint Sunalta
DowntownWest / Kerby
Lions Park
1. Train Origin
2. # of People Waitng, Getting on/off
Train 1Train 2
PLATFORMPLATFORM
Architecture Student
3. Morning, Noon, Evening
Filming
# of people getting on and off each trainat different times of the day
Saddletowne
Somerset
Neutral
Tracking Movement
LATFORM
Process Diagram
Frames from GIF image
Assignment 3MappingPart 2
Century Gardens
8th Street StationMapping Direction of Exiting Passengers at NoonPositions recorded after 15 seconds of train doors opening
Saddletowne TrainSommerset Train
Section
1:200
Assignment Introduction to Rendering
Assignment 4Digital FabricationPart 1
Butt Joint LaminationAlligator Joint
Model 3Model 2
Model 1
Assignment 5Tectonics
SANAA- Toledo Museum of Art Glass Pavillion
Assignment 6Surface Articualtion
Assignment 7Layout
Construction Diagram
Digital Fabrication Part 1
Material:1/8 inch acrylic
Digital fabrication allows for physical construction methods that would be either very challenging or impossible to do by hand. However it also introduces some specific construction techniques that are condusive to laser cut models.
This project employs three different joining techniques
1) Box Joint 2) Butt Joint 3) Lamination
Each model uses one or more of the listed techniques in order to demonstrate their benefits and or downsides.
1/8 inch acrylic is the material of choice in order to highlight the joining process that would not be visible with the use of opaque materials like plywood. This particular thickness was selected in order to visualize a higher density lamination process as well as thinner walls on enclosed box designs versus thicker material.
Model 1Model 2Model 3 Model 1 Model 2 Model 3 Elevation 2Elevation 1
Joining Methods
This project is based off of a previous assignment that took the theme of compression and was used to transform a simple cube into a final form that conveys the theme.
LaminationButt JointBox Joint
Model 1
Model 3
Model 2
Construction Diagram
Digital Fabrication Part 1
Material:1/8 inch acrylic
Digital fabrication allows for physical construction methods that would be either very challenging or impossible to do by hand. However it also introduces some specific construction techniques that are condusive to laser cut models.
This project employs three different joining techniques
1) Box Joint 2) Butt Joint 3) Lamination
Each model uses one or more of the listed techniques in order to demonstrate their benefits and or downsides.
1/8 inch acrylic is the material of choice in order to highlight the joining process that would not be visible with the use of opaque materials like plywood. This particular thickness was selected in order to visualize a higher density lamination process as well as thinner walls on enclosed box designs versus thicker material.
M 1M 2M 3 Elevation 2Elevation 1
Joining Methods
This project is based off of a previous assignment that took the theme of compression and was used to transform a simple cube into a final form that conveys the theme.
M 1 M 2 M 3
Lamination
Butt Joint
Box Joint
Model 1
Model 3
Model 2
Assignment 8Measured Drawing AssignmentPart 1
Assignment 8Measured Drawing AssignmentPart 2