Post on 10-Mar-2018
transcript
6.25.07
FABRIC-SHIELD STORM SHUTTERS
- 11.19 -
Wayne-Dalton FABRIC-SHIELD Pull-Down Storm Shutters are the newest product in the Fabric-Shield family. This revolutionary new product is designed to cover windows, doors and other home openings to protect against damage caused by wind, rain, and storm-driven projectiles. The patented design of this shutter utilizes an architecturally pleasing 4” square canister and quickly operates by simply pulling the fabric barrier down until it locks in the closed position.
The product has been tested in accordance with the Florida Building Code and the International Building Code (#FL2753 and Texas Department of Insurance Product Evaluation #SHU-112).
The units are shipped almost fully assembled, allowing for fi nal assembly to be done in just a few minutes, thereby saving signifi cant labor costs.
Storm shutters are perfect for second fl oor or high-rise applications. Storm Shutters are also perfect for the elderly or disabled, since it requires no lifting, tools, or assembly to deploy before a storm. The fabric panels are UV, mold, and mildew resistant, and can be used as a sunshade all year round.
FABRIC-SHIELD™ PULL-DOWN STORM SHUTTERS
Attractive - Architecturally pleasing: does not detract from architectural design of the home.
Can be quickly deployed for hurricane protection simply by pulling it down until it locks in place.
Translucent, allowing diffused light to enter. Can be used as a sun shade.
Florida Product Approved #FL8781. Texas Dept. of Insurance approved
TESTED EFFECTIVEWayne-Dalton FABRIC-SHIELD Pull-Down Shutter Storm Panels pass windload, impact and cycling testing in accordance with:• Design Pressure = ±57 psf • Florida Building Web: www.fl oridabuilding.org• TDI SHU-112 • TX Dept. of Insurance Web: www.tdi.state.tx.us• ASTM E1886 & ASTM E1996
Cost effective.
Custom-sized to fi t a wide variety of openings.
Assembles quickly: Installers can fabricate and install in less than 15 minutes.
Above: Patented compact design: shutter canister is only about 4” square.Call your Eco-$mart Representative
for more information today!
1-888-329-2705
6.25.07
FABRIC-SHIELD STORM SHUTTERS
- 11.21 -
FABRIC-SHIELD™PULL-DOWN STORM SHUTTER ORDER FORM
Manufactured by
SHUTTER MEASUREMENT NOTES:• Refer to installation documents & engineering drawings• Minimum 2 inch* edge distance for all anchors into concrete• Minimum 2 ½ inch* distance for all anchors into hollow block• Minimum 1 ¼ inch & maximum 2 ¼ inch from the edge of the fi nish is recommended for wood framing• Fastener holes to be drilled in the fi eld. Use 7/16” as illustrated (this refl ects the change in fastener hole position).*Edge distance excludes stucco, foam, brick and otherexterior wall fi nishes.LOCK PIN NOTES:• Each unit will include 2 – 6” lock pins as standard equipment• Custom lock pin can be ordered in length up to 60” ($10/set)• Recommended custom lock pin measurement is: Span / 2 * .67 (round to the nearest whole inch).
Qty SpanOverall Height
Custom Lock Pins? Yes/No
Custom Lock Pin Length Special Instructions
Date: ____________________________________________Business Name: ___________________________________ Account #: ____________________Phone #: _________________________________________ FAX #: ________________________Contact Name: ______________________________________Job Name/P.O.# : ____________________________________
OVERALL HEIGHT
(MAX 96”)
SPANFASTENER CENTER TO CENTER
OPENING WIDTH
(MAX 84”)
¾ ”
7⁄16”
1-11⁄16”
5-⅞ ”
SEE NOTES
SEE NOTES
CURTAIN BAR1.835” HEIGHT LOCKING
PINS
Note: new improvements to the pull-down shutter are not pictured.
6.25.07- 11.22 -
FABRIC-SHIELD STORM SHUTTERS
ENGINEERING
6.25.07
FABRIC-SHIELD STORM SHUTTERS
- 11.23 -
ENGINEERING
6.25.07- 11.24 -
FABRIC-SHIELD STORM SHUTTERS
6.25.07
FABRIC-SHIELD STORM SHUTTERS
- 11.25 -
6.25.07- 11.26 -
FABRIC-SHIELD STORM SHUTTERS