Post on 22-Jan-2015
description
transcript
American Electronic Resource, Inc.First Line of Defense Against Counterfeits
Robert Hammond, President and CEO
Corporate Headquarters3505 Cadillac Avenue, Building ACosta Mesa, California 92626 USA
robb@aeri.comwww.aeri.com
© 2009 AER, Inc.
Discover the Difference
Discover the Difference
Using an Independent Distributor as a Defense Against Counterfeits
Discover the Difference
Part Search Engines/Supplier Knowledge
In this example, the suppliers with the desirable quantities are known to sell poor quality components. Note: This is a military part number and there are many Asian distributors that display large quantities available.
Perform a thorough background check on all new suppliers. Most broker organizations are very small and do not have established quality control procedures in place. We have more than 10,000 brokers in our database. Of those only 200 have more than 10 employees and quality control procedures for their staff. That leaves us 9,800 to fall victim to. Many brokers are working out of their home. All someone needs is a phone, fax and e-mail address and they are in business.
1) Verification of address to be a legitimate place of business.
2) Investigation of industry related memberships to establish how long they have been in business. If a broker has been in the industry for a substantial length of time then they should be a member of one or more industry group. The ERAI is the most common membership for an established distributor. Part search engine memberships also assist us to determine a suppliers length of time in the industry.
3) Check at least 3 references. This includes a question about the length of their business relationship, how many transactions have been completed and the dollar amounts of the transactions. If the supplier offers a reference with minimal transaction history, that is a bad sign.
Discover the Difference
Broker Purchasing Steps
Eliminate all non-franchised distributors in China from AVL. The Chinese government controls the franchise channel leaving the open market with all of the low quality and used parts. Before our “No China” policy in 2005, 50% of our purchase orders from the region were counterfeits.
Request verbally and in writing that suppliers do not supply parts from China. It is important to do both to show our seriousness about the “No China” request. There are many brokers that will lie to make a buck. We caught one lying when we received a box from a US broker with parts wrapped in a Chinese newspaper.
Track and eliminate suppliers who provide counterfeit components. Our largest accomplishment in the fight against counterfeits has been our practice of removing vendors from our AVL that have sent counterfeits to us more than once. Many of our competitors do not like to close doors for fear of losing sales, but we know that these losses will be regained with increased confidence from our customers.
Check known part history with each new customer requirement for it’s counterfeit status on ERAI and GIDEP.
Discover the Difference
Broker Purchasing Steps
Discover the Difference
Broker Purchasing Steps
Track all supplier history and use a rating system which encourages purchasing fromthe best suppliers.
Quality control technicians must be thoroughly trained in counterfeit detection. There are
numerous conferences, publications and now, the ability to be trained and certified to
the IDEA-STD-1010-A standard through the IDEA-ICE-3000 exam process.
Use of microscopy during the QC process. The
counterfeiters are hoping we are not trained and
do not use a microscope. Their work looks
great to the naked eye, but once they alter the
part a microscope has no trouble pointing
it out. A well trained quality control technician can
catch 98% of all re-marked parts. It is not that
hard with a little training and experience.
Forged relationships with test facilities for
procedures from a simple de-capsulation to 100%
functionality testing.
Discover the Difference
Quality Control
Discover the Difference
Simple Tools for Detecting Counterfeits
1. Minimum 30X Microscope with built in camera2. MIL-STD-883 Method 2015 acceptable solution for
part markings to withstand of consisting of 3 parts mineral spirits and one part alcohol
3. Acetone and cotton swabs4. Razor blade for scraping surfaces5. Bar code reader with simple software6. Micrometer7. Access to datasheets8. De-capsulation device
Discover the Difference
Packaging Inspection
1. Verification that the date code, lot code and country of origin on the parts match the information on the manufacturer’s label
2. Date codes that are impossible. Example 0657 or 0951
3. Misspellings on the manufacturer’s labels
4. Omissions of important information such as a lot code
5. Packaging meets the manufacturer’s specs for the parts. Some examples are; a. Absence of desiccant or the humidity indicator card for moisture
sensitive components b. Parts on a reel of 2500 pieces that are specified to be on a reel of 2000
7. RoHS compliance marked on label, but the parts themselves are not marked with the correct RoHS designation
8. Manufacturers logos are correct and the proper style for the date of manufacture
Discover the Difference
Packaging Inspection
9. Verification that the bar code on the label matches the part description. Often the counterfeiters do not know how to make a bar code so they copy one from another source which does not match.
Discover the Difference
1. Separation of all production lots
2. 100% visual inspection of the product in it’s packaging (tubes, trays, reels) in order to locate non conformities.
3. Inspection of a sample group removed from it’s packaging using the derivation method Military Standard 414 (AQL 1%, Inspection Level IV). Samples are examined using microscopy. A marking permanency test (MIL STD-883 Method 2015), acetone test and scrape test are performed.
4. Documented inspection records kept.
5. Digital image storage of at least 1 part per lot
Part Inspection
Discover the Difference
Foreign Material in Mold Cavities
Examining the indents is our number one way of detecting counterfeit components. The counterfeiters have a very difficult time keeping the indents clean and consistent during their refinishing process. When sanding off the part number the depth changes. Blacktopping the parts often fills the cavities.
Discover the Difference
Comparing Mold Cavities
All of these parts have the same lot code on the tops. Compare the shapes and characters in the indents. Parts with the same lot code should all be identical.
Discover the Difference
Countries of Origin
Most parts, which are large enough to write a country of origin, display where it was manufactured somewhere on the part. It is commonly placed in the indents, but it can be written anywhere on the part. We have questioned the component manufacturers and all of them we have spoken to say that a part with the same lot code as another cannot be manufactured in different countries.
Discover the Difference
Texture
Plastic Electronic Components are typically made with a mix of fine glass and plastic. The surface of the molded package is textured when it is removed from the mold. The counterfeiters have come up with a very good mixture to create a similar surface on top of the original surface. With the naked eye it is almost impossible to determine the difference between the original surface and a fake surface. By taking a close look through the microscope there are many signs that can help you determine the authenticity of a component.
Natural with gritty texture Resurfaced with bubbly texture
Often if you look at the edge of the parts you can see the change in texture from the blacktopping. The top of the part, where it has been blacktopped, is shiny and the side of the part has a duller finish.
Discover the Difference
Texture Examples
Parts coming straight out of a mold will not have any marks that create a directional pattern. These types of marks are made when the counterfeiters are sanding off the top or bottom markings to prepare the part for remarking.
Discover the Difference
Texture Examples
Discover the Difference
Imperfections
All of the manufacturers, which we have spoken to, state that they have high quality standards which preclude them from major imperfections. The part numbers are to be in a certain location on the part and they are not to be crooked, misspelled, or out of alignment. The logos are also monitored very closely and should not vary from part to part.
Left corner should be “B”
The natural plastic and glass mixture does not come off of the surface with acetone. This part looked perfect to the naked eye. Once under a microscope we could see that the texture did not look like the natural plastic and glass mixture. To test our findings we took a cotton swab dipped in acetone and rubbed the surface for a few seconds. It was clear that there was some sort of foreign substance on the surface. The cotton swab should be completely clean.
Discover the DifferenceDiscover the Difference
Blacktopping
The counterfeiters are getting more sophisticated every day. Due to an increase in returns they have now come up with blacktopping materials that withstand acetone. When we see a suspicious surface under the microscope, and acetone will not remove it, we take a simple razor blade and scrape both sides of the part. If the parts surface flakes off, like the part on the left, we know that it is blacktopped. A sure test is to scrape the bottom of the part to see if it behaves the same way as the top when scraped. The same part’s underside plastic (to the right) just received scratches. There was no flaking like the top which was blacktopped.
Top Bottom
Discover the Difference
Blacktopping
Discover the Difference
Ceramic packages are not exempt from blacktopping. This part looked great to the naked eye. Our QC team noticed the texture discrepancy under the magnification of a microscope. The surface could not be removed with acetone so we scraped the surface with a razor blade. Scary fact: These were purchased from an aviation broker.
Discover the DifferenceDiscover the Difference
Blacktopping/Ceramic Package
Discover the Difference
Once a counterfeit is detected a number of steps should be taken;
1. Suspension of purchases from the supplier, pending a supplier
quality investigation.
2. The counterfeit parts must be moved to a quarantine shelf for disposition. When legally possible parts should be destructed or made unusable. Keep five pieces as a sample for supplier evaluation.
3. The part number is marked in our data system as highly counterfeited to heighten the purchasing and inspection process for future orders.
4. Report the part to the Electronic Resellers Association and GIDEP as a precaution for other users of the same product.
Counterfeits Found
De-capsulation is a very valuable tool for parts you are having difficulty determining if they are counterfeit. After performing all of the simple non destructive tests the part may be opened and the die can be verified. This does not guarantee all of the parts in the lot are the same, but it is a useful tool and is much cheaper than testing ($200).
Discover the DifferenceDiscover the Difference
De-capsulation
Discover the Difference
Separation of all production lots.
100% visual inspection of the product in it’s packaging (tubes, trays, reels) in order to locate non conformities.
Inspection of a sample group, minimum 25 pieces, or sample quantity derivation method Military Standard 414 (AQL 1%, Inspection Level IV) for lot quantities over 25. Samples are examined using microscopy, a marking permanency test (MIL STD-883 Method 2015), acetone test and scrape test are performed.
Digital images of 3 samples from each lot.
X-ray examination of up to 30 units looking for part-to-part consistency (die, lead frame, wire bonding)
De-capsulation of up to 3 pieces
Die images and component engineer’s comment on test results (consistent with datasheet, anomalous, or highly suspect)
Documented inspection records provided with each order.
Authentipro
Authentipro is a program designed for our customers who require 100% assurance that the product is authentic. The program highlights include;
Discover the Difference
Electrical Testing
It is very important that your company has a working relationship with a test house, however, you should not use a test house as your only counterfeit detection procedure.
Testing is not a 100% guarantee against counterfeits. A typical counterfeit is made from a used or old part that is basically the same. The only change might be the finish, date code, temperature range or manufacturer. The parts might test good with general testing, but once on the board they can fail. Different manufacturers and date codes have slightly different parameters which are not picked up during a general test.
Not all parts can be tested. Often times the testing can cost immeasurably more than the parts themselves. We have received quotes from test houses for $11,000 to test $500 worth of parts. Other times test houses have explained to us that they would have to hire additional staff and labor for months to develop a proper program for full functional testing.
Testing takes time. Buyers looking for hard to find parts often are already running on a late schedule with no time to spare. The additional week or more can cause line down situations.
Discover the Difference
Electrical Testing
There have been reports of test houses not actually performing the tests stated in their documentation. Many test houses are very busy and cannot keep up with the workload due to the rise in counterfeit components. Greed has reached into their organizations as well as the counterfeiters.
Test houses are reporting that brokers are ignoring their suggestions for deeper testing. Deceitful brokers are pushing for a pass test result by requesting the most simple test possible.
The manufacturer and test facility should communicate directly with each other to assure that the testing is being performed to the level of testing requested. The facilitator of testing has a large array of testing options and most broker organizations do not have engineering departments to determine what tests are necessary. Full datasheet testing is always recommended, but may not always be an option, dependent on price and availability of hardware and software.
Locate top notch independent distributors
Audit your current suppliers facility and counterfeit avoidance strategy
Increase your counterfeit detection capabilities
Test all high reliability parts from non-franchise distribution
Discover the DifferenceDiscover the Difference
Conclusion
Discover the Difference
Qualifications
15 years in business
AS9120 Certified
ISO 9001:2000 Certified
ESD/ANSI S20-20.1999 Certified
IDEA Founding Member
ERAI 10 Year Member