Post on 22-Mar-2016
description
transcript
PAGE 3 HEADLIGHT OIL RADIATOR SCREEN/GRILL & ANTI GLARE SHIELD
PAGE 5 HEADLIGHT SCREEN & ANTI GLARE SHI
PAGE 7 QUICK HEADLIGHT SCREEN R1150GS&A
PAGE 9 QUICK RELEASE FASTNERS
HE
AD
LIG
HT
OIL
RA
DIA
TO
R S
CR
EE
N/
GR
ILL
& A
NT
I GL
AR
E S
HIE
LD
1
3
7
5
Tool Required: T27 On Left & Right Indicator, Then PullIndicator Out Of Its Frame Location Hole
Torx Bit. Undo Bolt
The Stainless Steel Bracket Should BePositioned Under The Indicator Lug &The Torx Bolt Holes Should Be In Line
Visual Of: Both Stainless SteelBrackets Mounted Correctly
Tools Required: 2.5mm Allen Key &7mm Ring Spanner
2
6
4
8
Take Note At This Point Of Bolt & LugHole Positions When Marrying TheStainless Steel Bracket To The Indicator
Mount M4 Bolts From The Front, PassingThem Through The Screen and StainlessSteel Bracket, Then Screw Nut On To Rear.Do Not Tighten Fully Until All FixingsAre In Place
Mount Indicator With Stainless SteelBracket, So Indicator Lug Locates In ToIts Frame Hole. Screw Torx Bolt UpUntil Tight. Repeat On Other Side
When Mounting Screen/Grill, AngleThe Part So Grill Passes Under FrameBar & Then Rotate So Screen HolesMarry Up To Stainless Steel Bracket Holes
HE
AD
LIG
HT
& A
NT
I GL
AR
E S
HIE
LD
1
3
7
5
Tool Required: T27 On Left & Right Indicator, Then PullIndicator Out Of Its Frame Location Hole
Torx Bit. Undo Bolt
The Stainless Steel Bracket Should BePositioned Under The Indicator Lug &The Torx Bolt Holes Should Be In Line
Visual Of: Both Stainless SteelBrackets Mounted Correctly
Tools Required: 2.5mm Allen Key &7mm Ring Spanner
2
6
4
8
Take Note At This Point Of Bolt & LugHole Positions When Marrying TheStainless Steel Bracket To The Indicator
Mount M4 Bolts From The Front, PassingThem Through The Screen & StainlessSteel Bracket, Then Screw Nut On To Rear.Do Not Tighten Fully Until All FixingsAre In Place
Mount Indicator With Stainless SteelBracket, So Indicator Lug Locates In ToIts Frame Hole. Screw Torx Bolt UpUntil Tight. Repeat On Other Side
When Mounting Headlamp ProtectorAlign So Screen Holes Marry Up ToStainless Steel Bracket Holes
HE
AD
LIG
HT
SH
IEL
D R
115
0G
S&
A
7
6
8
1Kit Contents: Tool Required: T25 Torx Bit.1 x Main Screen, 2 x Brackets
2 x M5 Stainless Steel Bolts4 x Quick Release FastenersWhen Received Kit May BePart Assembled
Undo Screws & Remove Them2 x Stainless Steel Pillar Nuts From Left & Right Handside Of
Headlight Surround, ReplaceWith Stainless Steel Pillar NutsDoing Up Until Finger Tight
2
Tool Required: 8mm Socket & Drive.Do Stainless Steel Pillar Nuts UpUntil Tight
3Tool Required: 3mm Allen Key.Marry Screen Screws Up To EndsOf Stainless Steel Pillar NutsLocate Allen Key Through HoleOnto Head Of Screw & Do UpUntil Tight
4
Pulling Back On The FastenerKnob Will Release ScreenIn Seconds For Ease OfMaintenance
5Visual Of: Both Stainless Steel
Make Sure There’s No Gap
Pillar Nuts & Brackets With
Between The Screen &
Screen Removed. To Reattach
Brackets & Fasteners Are In
Against Screen. Once The
Screen Marry Screen Upto
There Unlocked Position
Fastener Is In Position Push
Brackets & Align Holes Up
Unlocked Position
Fastener Knob
Fastener Pin& Bayonet
Locked Position
Waist Washer
Unlocked Position
Fastener Knob
Waist Washer
Locate Fasteners Into Screen &
The Knob In Until The
Bracket Hole So Waist Washer Is
The Fastener Locks In Place
QU
ICK
RE
LE
AS
E F
AS
TE
NE
RS
1
3
7
5
Tools Required: 2.5mm Allen Key& 7mm Ring Spanner
Fastener Knob
Fastener Pin& Bayonet
Waist Washer
Make Sure The Screen &Bracket Holes Are Aligned
x
xLocate Fastener Into Screen & Bracket HoleSo Waist Washer Is Against Screen
Remove All 4 Nuts & Screws
2
6
4
8When All 4 Fasteners Are In PositionScreen Will Be Secure. To Release ScreenPull Fastener Knob Out Until It Releases.To Re-Secure Repeat Sections 4 Thru To 7
& There Is No Gap Between The Two
Once The Fastener Is In Position Push TheKnob In Until The Fastener Locks In Place