Post on 06-Apr-2018
transcript
8/3/2019 Flow Control Catalog Tectool
1/14
FLOW CONTROL
EQUIPMENT
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
TechToolTechToolTechToolTechToolInternationalInternationalInternationalInternational
8/3/2019 Flow Control Catalog Tectool
2/14
WARRANTY
1. TechTool International warrants only that the merchandise, products, or parts thereof, sold or rented to customers,
shall be free from original defects in materials and workmanship for one year from date of shipment and not that
they will accomplish any particular results. There are no warranties, expressed or implied, of merchantability, fitness or
otherwise which extend beyond those stated in the immediately preceding sentence. Liability of TechTool International and
the sole remedy in any cause of action, (whether in contract, tort, breach of warrantee or otherwise) of any one
damaged under this warranty, is exclusively limited to replacement of, or at TechTools option, to the allowance of
credit, for defective equipment or parts, which may be returned within one year after date of shipment from
TechTool Internationals warehouse, provided that all transportation charges are prepaid to TechTool Internationalin Houston, Texas, and which upon examination shall disclose original defects to the satisfaction of TechTool
International,. This guarantee does not include payment of labor charges for replacement of parts, repairs, or any
other work done. In no event shall TechTool international be liable for special, incidental, indirect, punitive or
consequential damages of any kind.
2. Services rendered by TechTool International in connection with rental, sale or installation of its products, consist
only of technical advise as to inspection, operation, or use of such products. When any such services are rendered,
customer will retain full custody, control, and supervision of the work and or the well and the conduct of the
operation thereof, and a representative of the customer shall be present with full authority to direct operations.
3. Customer will indemnify and hold TechTool International harmless from any and all liability or claim of liability to
any person, firm, or corporation for damage to person or property arising out of, or in connection with the use of any
TechTool International products sold or rented hereunder, or the rendering of services hereunder, except for damage
caused solely by the willful negligence of TechTool International.
4. Products not sold to customer will remain the property of TechTool International, and are not to be repaired or
modified without the consent of TechTool International. If lost or damaged beyond ordinary wear and tear, such
products will be charged for as provided for by TechTool Internationals current pricing policy. TechTool
International upon ten days notice may repossess any equipment belonging to TechTool International in customers
possession.
5. If property belonging to TechTool International is lost in or out of the well, customer shall either recover such
equipment at its cost and return to TechTool International or at TechTool Internationals request pay TechTool
International therefore. If the equipment is recovered in satisfactory condition at a later date, the customer may
return it to TechTool International in accordance to TechTool Internationals returns and cancellation policy.
6. TechTool International assumes no responsibility relating to cost of removing any equipment that necessitates the
removal of the tubing.7. All of the preceding terms and conditions shall apply between TechTool International and any service company,
operator, or any parties, selling renting or using TechTool International products, parts or service.
8. Except for warranties specifically set forth herein, there shall be no express warranties or implied warranties. There
shall be no warranty of merchantability with respect to the goods sold hereunder. Furthermore TechTool
International makes no warranty that the goods sold or rented hereunder are fit for any particular purpose. In
addition, buyer in purchasing the goods sold hereunder expressly agrees that the liability of TechTool International,
if any, shall be limited to the replacement in accordance with section (1) hereof.
9. No agent, or representative of TechTool International has any authority to bind TechTool International to any
affirmation, representation or warranty concerning goods sold or rented, and unless an affirmation, representation or
warranty made by agent, employee or representative is specifically included within a written agreement, it shall not
be enforceable by the buyer or the renter.
10. The warranty herein is for the benefit of the initial purchaser only and no assignees, transferees, or third parties,
shall have any rights against TechTool International.
11 TechTool International reserves the right to modify and improve the design and method of construction of any of its
merchandise, without incurring any obligation to install such modification or improvement on merchandise
manufactured, sold, or rented, prior to or after the modification or improvement was instituted.
12 These general terms and conditions shall constitute a contract between customer and TechTool International. Such
contract shall be governed, construed, and enforced in accordance with the laws of the State of Texas in the United
States of America.
8/3/2019 Flow Control Catalog Tectool
3/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TF TOP NO-GO / SELECTIVE SEATING NIPPLEThe TechToolTechToolTechToolTechToolmodel TF Seating Nipple provides Top No-Go or Selective locating
for various flow control devices in the producing string.
APPLICATIONS
Land blanking plugs to shut in well or to test the production tubing.
Land velocity type safety valves.
Land equalizing check valves.
Land equalizing blanking plugs.
Land chokes to reduce surface flowing rates and pressures.
Land instrument hangers with pressure and temperature recorders.
All premium threads available.
MATERIAL SELECTION4140 / P110 - 110,000 Yield 9C1M / 9 Chrome 1 Molly - 80,000 Yield
Standard Service High Resistance to Corrosion in Sour Gas
Environments
4140 / L 80 - 82,000 Yield 316 S.S. - 40,000 Yield
Resist Corrosion in Sour Gas
Environments
High Resistance to Corrosion in Sour Gas
Environments
DIMENSIONAL DATA
SEAL
SIZE BORE A *B C
1.50 1.500 1.875 11.0- +5.44
1.56 1.562 2.000 15.0 +5.50
1.62 1.625 2.000 +5.44
1.78 1.781 2.312 12.0- +6.50
1.81 1.812 2.312 17.0 +6.44
1.87 1.875 2.312 +6.38
2.25 2.250 2.812 +6.75
2.31 2.312 2.812 13.0- +6.69
2.56 2.562 3.185 18.0 +9.37
2.75 2.750 3.375 +7.31
2.81 2.812 3.375 +7.31
3.68 3.688 4.375 16.12- +7.50
3.81 3.812 4.375 18.62 +7.50
* Note: Length of the Nipple varies slightly with different thread and bore relationships.
8/3/2019 Flow Control Catalog Tectool
4/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TFWG BY-PASS BLANKING PLUG
The TechToolTechToolTechToolTechToolmodel TFWG Top No-Go, By-Pass Blanking Plug, allows fluid to by-
pass through the side ports while it is being run into the well. Once the plug is lockedin place in the TF Seating Nipple, pressure can be held in either direction.
Removing the Equalizing Mandrel allows the pressure above and below the plug to
equalize, prior to pulling the TFWG from the well.
To run: use a C-1 Running Tool. To release: use a B Probe.
MATERIAL SELECTION4140 / P110 - 110,000 Yield 9C1M / 9 Chrome 1 Molly - 80,000 Yield
Standard Service High Resistance to Corrosion in Sour
Gas Environments
4140 / L 80 - 82,000 Yield 316 S.S. - 40,000 Yield
Resist Corrosion in Sour Gas
Environments
High Resistance to Corrosion in Sour
Gas Environments
PARTS LIST
ITEM PART NAME NO PART NO.
REQ. 2.25/2.31 2.75/2.81
1 Fishing Neck 1 42VPP4 42VPP19
2 W-2 Sub Assembly 1 42VPP1 42VPP16
3 Washer 1 42VPP10B 42VPP26
4 O-Ring 1 42VPP41/#018
5 Lock Ring Segments 2 42VPP10
6 Stop Ring 1 42VPP10A
7 Packing Unit Assy. 1 2.25/2.31 2.75/2.81
8 Brass Shear Pin 1 42VPP43/.250O.D.9 O-Ring 2 42VPP40/#113
10 Mandrel 1 42VPP7
11 Bottom Sub 1 42VPP9 42VPP24
12 O-Ring 1 42VPP42/#115
13 Plug 1 42VPP8
DIMENSIONAL DATASIZE NO GO A B C D E F G H I
2.25 2.302 1.750 2.156 1.156 2.250 1.640 3.797 1.875 1.875
2.31 2.365 1.750 2.156 1.156 2.250 1.640 3.797 1.875 1.875 Brass Locking Pin
2.75 2.802 2.313 2.656 1.188 2.250 1.688 4.313 1.875 5.374 O.D. - .1252.81 2.865 2.313 2.656 1.188 2.250 1.688 4.313 1.875 5.374
SIZE PART NO.
2.25 42VP1
2.31 42VP2
2.75 40VP1
2.81 42VP6
8/3/2019 Flow Control Catalog Tectool
5/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TR BOTTOM NO-GO SEATING NIPPLEThe TechToolTechToolTechToolTechTool model TR Seating Nipple provides bottom no-go locating for
various flow control devices in the producing string.
APPLICATIONS
Land blanking plugs to shut in well or to test the production tubing.
Land velocity type safety valves.
Land equalizing check valves.
Land equalizing blanking plugs.
Land chokes to reduce surface flowing rates and pressures.
Land instrument hangers with pressure and temperature recorders.
All premium threads available.
MATERIAL SELECTION4140 / P110 - 110,000 Yield 9C1M / 9 Chrome 1 Molly - 80,000 Yield
Standard Service High Resistance to Corrosion in Sour Gas
Environments
4140 / L 80 - 82,000 Yield 316 S.S. - 40,000 Yield
Resist Corrosion in Sour Gas
Environments
High Resistance to Corrosion in Sour Gas
Environments
DIMENSIONAL DATA
SEAL NO GO
SIZE BORE BORE A *B C
1.50 1.500 1.447 1.875 11.0- 4.88
1.56 1.562 1.510 2.000 15.0 4.86
1.62 1.625 1.572 2.000 4.86
1.78 1.781 1.728 2.312 12.0- 5.81
1.81 1.812 1.760 2.312 17.0 5.81
1.87 1.875 1.822 2.312 5.81
2.25 2.250 2.197 2.812 6.12
2.31 2.312 2.260 2.812 13.0- 6.12
2.56 2.562 2.443 3.185 18.0 8.843
2.75 2.750 2.697 3.375 6.70
2.81 2.812 2.759 3.375 6.70
3.68 3.688 3.625 4.375 16.12- 7.37
3.81 3.812 3.759 3.375 18.62 7.37
Note: Length of the Nipple varies slightly with different thread and bore
relationships.
8/3/2019 Flow Control Catalog Tectool
6/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TRZG BY-PASS BLANKING PLUG
The TechToolTechToolTechToolTechToolmodel TRZG By-Pass Blanking Plug allows fluid to by-pass through
the side ports while it is being run into the well. Once the plug is locked in place in
the TR Seating Nipple, pressure can be held in either direction. Removing the
Equalizing Mandrel allows the pressure above and below the plug to equalize, prior
to pulling the TRZG from the well.
To run: use a C-1 Running Tool. To release: use a B Probe.
MATERIAL SELECTION4140 / P110 - 110,000 Yield 9C1M / 9 Chrome 1 Molly - 80,000 Yield
Standard Service High Resistance to Corrosion in Sour
Gas Environments
4140 / L 80 - 82,000 Yield 316 S.S. - 40,000 Yield
Resist Corrosion in Sour Gas
Environments
High Resistance to Corrosion in Sour
Gas Environments
PARTS LIST
ITEM PART NAME NO PART NO.
REQ. 2.25/2.31 2.75/2.81
1 Fishing Neck 1 42VPP4 42VPP19
2 Z-2 Sub Assembly 1 42VPP3 42VPP18
3 Washer 1 42VPP10B 42VPP26
4 O-Ring 1 42VPP41/#018
5 Lock Ring Segments 2 42VPP10
6 Stop Ring 1 42VPP10A
7 Packing Unit Assy. 1 2.25/2.31 2.75/2.81
8 Brass Shear Pin 1 42VPP43/.250O.D.9 O-Ring 2 42VPP40/#113
10 Mandrel 1 42VPP7
11 Bottom Sub 1 42VPP9 42VPP24
12 O-Ring 1 42VPP42/#115
13 Plug 1 42VPP8
DIMENSIONAL DATASIZE NO GO A B C D E F G I
2.25 2.240 1.750 2.156 1.156 2.250 5.440 2.156 5.062
2.31 2.302 1.750 2.156 1.156 2.250 5.440 2.156 5.062 Brass Locking Pin
2.75 2.740 2.313 2.656 1.188 2.250 6.000 2.156 5.093 O.D. - .1252.81 2.802 2.313 2.656 1.188 2.250 6.000 2.156 5.093
SIZE PART NO.
2.25 42VP5
2.31 42VP9
2.75 40VP3
2.81 42VP8
8/3/2019 Flow Control Catalog Tectool
7/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TL SLIDING SLEEVEThe TechToolTechToolTechToolTechToolmodel TL Sliding Sleeve is a downhole flow control device mountedin the production string to provide communication between the tubing and the casing
annulus. Shifting an inner sleeve either up or down using standard wireline methods
opens it.
DESIGN FEATURES
Features a nipple profile and a packing bore above and below the communication
ports.
Dependable, molded seals on the inner sleeve
Ports can be closed without leaving any obstructions in the tubing once the the
shifting operation is completed.
The model TD-2 Shifting Tool is used to open (jarring up) or close (jarring
down) the TL Sliding Sleeve. All premium threads available.
Flow area through ports greater than the tubing.
MATERIAL SELECTION4140 / P110 110,000 Yield 9C1M / 9 Chrome 1 Molly 80,000 Yield
Standard Service High Resistance to Corrosion in Sour Gas
Environments
4140 / L 80 82,000 Yield 316 S.S. 40,000 Yield
Resist Corrosion in Sour Gas
Environments
High Resistance to Corrosion in Sour Gas
Environments
DIMENSIONAL DATA
SIZE SEAL BORE PART NO.
2.25 2.250 161225
2.31 2.313 161231
PARTS LIST
ITEM PART NAME NO. SIZE AND PART NO
REQ 2.25 2.31
1 Top Sub 1 161225-1 161231-1
2 O-Ring 2 165149.2
3 Middle Housing 1 161225-3
4 Replaceable Seals 2 165225-4
5 Closing Sleeve 1 161225-5
6 Bottom Sub 1 161225-6 161231-6Other sizes available
Note: Length of sleeve varies slightly with different thread and bore relationships.
8/3/2019 Flow Control Catalog Tectool
8/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TL SLIDING SLEEVEThe TechToolTechToolTechToolTechToolmodel TL Sliding Sleeve is a downhole flow control device mounted
in the production string to provide communication between the tubing and the casingannulus. It is opened by shifting an inner sleeve either up or down using standard
wireline methods.
DESIGN FEATURES
Features a nipple profile and a packing bore above and below the communication
ports.
Dependable, molded seals on the inner sleeve
Ports can be closed without leaving any obstructions in the tubing once the the
shifting operation is completed.
The model TD-2 Shifting Tool is used to open (jarring up) or close (jarring
down) the TL Sliding Sleeve.
All premium threads available. Flow area through ports greater than the tubing.
MATERIAL SELECTION4140 / P110 110,000 Yield 9C1M / 9 Chrome 1 Molly 80,000 Yield
Standard Service High Resistance to Corrosion in Sour Gas
Environments
4140 / L 80 82,000 Yield 316 S.S. 40,000 Yield
Resist Corrosion in Sour Gas
Environments
High Resistance to Corrosion in Sour Gas
Environments
DIMENSIONAL DATA
SIZE SEAL BORE PART NO.
2.75 2.750 161275
2.81 2.812 161281
PARTS LIST :
ITEM PART NAME NO. SIZE AND PART NO
REQ 2.75 2.81
1 Top Sub 1 161275-1 161281-1
2 O-Ring 2 165237-2
3 Middle Housing 1 161275-34 Replaceable Seals 2 165275-4
5 Closing Sleeve 1 161275-5
6 Bottom Sub 1 161275-6 161281-6Other sizes available
Note: Length of sleeve varies slightly with different thread and bore relationships.
8/3/2019 Flow Control Catalog Tectool
9/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TD-2 SHIFTING TOOLThe TechToolTechToolTechToolTechToolmodel TD-2 Shifting Tool is used to provide a safe, selective, and
controlled method of opening and closing L type Sliding Sleeves with slickwireline.
DIMENSIONAL DATA
SIZE A *B C
2.75 2.781 17.125 39.440
2.81 2.843 17.125 39.440* Adjust to this dimension,
PARTS LIST :
ITEM PART NAME NO. SIZE AND PART NO
REQ 2.75 2.81- TD-2 Tool Assy. - 45DV275 45DV281
1 Fishing Neck 1 V70230
2 Cap Screw 1 -20X-
3 Mandrel 1 V70197
4 Collet 1 V88912 V88913
5 Connecting Adjuster 1 V70368
6 Set Screw 1 -20X-
7 Control Sleeve 1 V70369
8 Nut 1 V964959 Set Screw 1 -20X1
10 Mandrel Spring 1 V70369
11 Retractor 1 V70196
12 Set Screw 1 -20X
13 Retainer Sleeve 1 V70193
14 Dog Spring 2 V80741
15 Shifting Dog 2 V96501
16 Pin 2 V70231
17 Key 2 V70089
**18 Shear Pin 3 V7023219 Set Screw 1 -20X
20 Dog Retainer 1 V70195
21 Thread Protector 1 V70194
22 Cap Screw 1 -20X-
** Tools assembled with three mild steel pins may be changed by operator, according
to well conditions. Check shear pin condition before each use.
8/3/2019 Flow Control Catalog Tectool
10/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TX SELECTIVE SEATING NIPPLE (OTIS TYPE)The TechToolTechToolTechToolTechTool model TX Seating Nipple provides full versatility for placement of
flow control devices in the producing string. Because they offer selective setting withthe TX Locking Mandrel, any number of TX Nipples with the same seal bore
size can be run in the production string.
APPLICATIONS
Land blanking plugs to shut in well or to test the production tubing.
Land velocity type safety valves.
Land equalizing check valves.
Land equalizing blanking plugs.
Land chokes to reduce surface flowing rates and pressures.
Land instrument hangers with pressure and temperature recorders.
All premium threads available.
MATERIAL SELECTION
4140 / P110 - 110,000 Yield 9C1M / 9 Chrome 1 Molly - 80,000 Yield
Standard Service High Resistance to Corrosion in Sour Gas
Environments
4140 / L 80 - 82,000 Yield 316 S.S. - 40,000 Yield
Resist Corrosion in Sour Gas
Environments
High Resistance to Corrosion in Sour Gas
Environments
DIMENSIONAL DATA
PART NO. SEAL
SIZE MATERIAL TYPE BORE A *B C
P110 L80 9CR1MO
1.50 121150 122150 123150 1.500 2.200 9.375 +4.937
1.62 121162 122162 123162 1.625 2.620 11.250 +4.806
1.87 121187 122187 123187 1.875 2.730 10.375 +4.775
2.31 121231 122231 123231 2.312 3.200 10.625 +4.635
2.75 121275 122275 123275 2.750 3.900 15.082 +5.550
2.81 121281 122281 123281 2.812 3.900 15.082 +5.500
* Note: Length of the Nipple varies slightly with different thread and bore relationships.
8/3/2019 Flow Control Catalog Tectool
11/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TX LOCK MANDREL (OTIS TYPE)The TechToolTechToolTechToolTechTool model TX Lock Mandrel is a Selective Set Lock designed to be
landed and locked, down-hole, in a TX Profile Seating Nipple. Equalizing SubAssemblies and a variety of sub-surface flow control devices may be attached to this
Lock Mandrel so that they may be locked in place in the production tubing, in order
to perform their designed functions.
APPLICATIONS
Land blanking plugs to shut in well or to test the production tubing.
Land velocity type safety valves.
Land equalizing check valves.
Land equalizing blanking plugs.
Land chokes to reduce surface flowing rates and pressures.
Land instrument hangers with pressure and temperature recorders.
MATERIAL SELECTION
4140 / L 80 - 82,000 Yield 9C1M / 9 Chrome 1 Molly - 80,000 Yield
Resist Corrosion in Sour Gas
Environments
High Resistance to Corrosion in Sour Gas
Environments
PARTS LIST
ITE
M
PART NAME NO. REQ.
1 Fishing Neck 1
2 Expander Sleeve 1
3 Key Retainer Sleeve 1
4 Spring 2
5 Key 2
6 Packing Mandrel 1
7 Packing Unit Assy. 1
8 #033 O-Ring (2.70 & 2.812 Sizes Only) 1
DIMENSIONAL DATA
Running Tool Type: X-Line
Pulling Tool Type: GR
SIZE A B C D1.817 1.38 13.38 1.00 1-3/8 14UN
2.313 1.81 13.50 1.38 1-3/4 12UN
2.750 2.31 13.75 1.75 2-1/4 SLB
2.813 2.31 13.75 1.75 2-1/4 SLB
8/3/2019 Flow Control Catalog Tectool
12/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TPX SELECTIVE BY-PASS BLANKING PLUG
The TechToolTechToolTechToolTechToolmodel TPX Selective, By-Pass Blanking Plug holds pressure from
both above and below once the plug is locked in place in a TX Seating Nipple.Removing the Equalizing Mandrel allows the pressure above and below the plug to
equalize, prior to pulling the TPX from the well.
o run Prong: use a SB Pulling Tool. To pull Prong: use a SB Pulling Tool.
o run Mandrel: use a X Running Tool To pull Mandrel: use a GR Pulling Tool
MATERIAL SELECTION4140 / L 80 - 82,000 Yield 9C1M / 9 Chrome 1 Molly - 80,000 Yield
Resist Corrosion in Sour Gas
Environments
High Resistance to Corrosion in Sour
Gas Environments
PARTS LIST
ITEM PART NAME NO
REQ.
1 Equalizing Prong Assy. 1
2 TX Locking Mandrel 1
3 # 033 O-Ring (Size 2.75 only) 1
4 Equalizing Sub Assy. 1
DIMENSIONAL DATASIZE A B C D
1.875 1.375 1.380 1.875 1.870
2.313 1.375 1.810 2.313 2.307
2.750 1.375 2.312 2.750 2.745
2.810 2.313 2.656 1.188 2.250
8/3/2019 Flow Control Catalog Tectool
13/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
MODEL TXA SLIDING SLEEVE (OTIS TYPE)The TechToolTechToolTechToolTechToolmodel TXA Sliding Sleeve provides a convenient way to establish or
shut off communication between the tubing and the casing annulus. Any number of
these sleeves can be run in a tubing string, and any number of them can may be
opened or closed in one run, using standard wireline methods.
DESIGN FEATURES
Features an X nipple profile above and a packing bore below the communication
ports.
Ports can be closed without leaving any obstructions in the tubing, once the
shifting operation is completed.
The Model B Shifting Tool is used to open (jarring up) or close (jarring down)
the TXA Sliding Sleeve.
All premium threads available.
MATERIAL SELECTION44140 / L 80 - 82,000 Yield 9C1M / 9 Chrome 1 Molly - 80,000 Yield
Resist Corrosion in Sour Gas
Environments
High Resistance to Corrosion in Sour Gas
Environments
Note: All Inner Sleeves are made of 17.4 PH Stainless Steel.
PARTS LIST
ITEM PART NAME NO. REQ.
1 Top Sub 1
2 Middle Sub 1
3 O-Ring 2
4 Inner Sleeve 15 Bottom Sub 1
6 Female Adapter Steel 4
7 V Packing 10
8 H2S / High Temperature O-Ring 2
9 Split Ring Segments 6
10 H2S / High Temperature O-Ring 1
11 Female Adapter Bottom 2
8/3/2019 Flow Control Catalog Tectool
14/14
PACKERS AN
COMPLETION EQUIPMEN
TechTool International
P.O. Box 451, Barker, TX 77413-0451, Phone: 281 578 0719, Fax: 281 578 3060, E-mail: tectool@aol.com
Model TD Collar Lock Model TDD Plug