Post on 21-Mar-2016
description
transcript
Partition and Workstation System
83
Furni ture Fabr icat ion
Partition Wall | Workstation System
Method: Design & FabricateWater Jet Cut Steel
Materials: Scrap steelPerforated steel screenFlat Iron
Process: Rhino 3d ModelLaser-Cut Process ModelsDXF File sent to Water jet CompanyMIG Welding, Spot weldingBending steelShear Cutting Steel
Furni ture Fabr icat ion
Workstation System
Includes:Stool Table Shelf attached to Partition Wall
Method: Design & FabricateWater Jet Cut SteelRemoved from Partition wallEasy Assembly tab joint systemCan Be taken apart for transportand spacial needs
Materials: Scrap steel
Process: Rhino 3d ModelLaser-Cut Process ModelsDXF File sent to Water jet CompanyMIG Welding, Spot weldingBending steelShear Cutting Steel
Furni ture Fabr icat ion
Partition Wall | Workstation System
Detail Images
Top | Table: interlocking cross mem-ber and tabbed joints
Bottom Left | Partition Wall: Nega-tive composition after workstation components are removed
Bottom Right | Stool: leg connec-tion
Furni ture Fabr icat ion
Interlocking Wine Rack
Method: Design & FabricateWater Jet Cut Steel
Materials: Scrap steelWine Bottles
Process: Rhino 3d ModelDXF File sent to Water jet CompanyTIG Welding, Tack weldsBending steelShear Cutting Steel
Furni ture Fabr icat ion
Interlocking Wine Rack
Process & Research:Interlocking Study Models
Materials:Cardboard Aluminum
Furni ture Fabr icat ion
Interlocking Wine Rack
Modular System
Furni ture Fabr icat ion
Walnut Headboard and Frame
Method: Design & Fabricate
Headboard:-Plane, cut, sand wood-Laser cut intricate design-Wire backlight system-Install steel frame
Bed frame:-Construct Pine platform-Construct legs and connections-Radial arm saw corner joints
Materials: Scrap Walnut from reclaimed lum-beryardJapanese Rice PaperAcrylicPineHardware, screws, brackets, electri-cal wire
Furni ture Fabr icat ion
Walnut Headboard and Frame
Process images:
Scrap wood in original stateConversion of hadsketch to computer drawing
Fabr icat ion Fac i l i t ies
Example of Architectural Render-ings
Interior gallery:Shows partition wall system on rails
Exterior Fabrication Shops:Shows components of Partition wall | Table & Stool in use |
1 2 5 6 7
10
11
12
13
14
16
15
N
N
2
1 3
Interior Gallery
Exterior Shops
Vel lum Furni ture Compet i t ion Cement Loop End Table
Method: Cement & concrete explorationUse of additives to manipulatecement consistency Use of tubing to achieve desired shape
Materials: CementTubingScrap steelFrosted Acrylic
Process: Material experimentationConceptual modelsSeveral iterationsMIG Welding on baseBending steelUse of skill saw on table top
Vel lum Furni ture Compet i t ion Designed by Alyssa ReddingWelding Work by Megan Repka
Method: Old Wheelbarrow reused as chair
Materials: Steel Flat Iron and RodRedwoodHemp
Process: Conceptual models3d Rhino ModelSeveral iterationsMIG WeldingBending steelSewn joints and edges
Furni ture Fabr icat ion Pipette LED Lamp
Designed by Alyssa Reddingin collaboration with Allison Pell & Megan Repka
Method: Use of discarded PipettesWiring LED LightsEach pipette was frosted by hand
Furni ture Fabr icat ion Subtle Ess Lamp
Designed by Alyssa ReddingIn collaboration with Allison Pell & Megan Repka
Method: Experimentation with light qualityFolding, sewing, slitting to create form
Materials: Stainless steelPaperRed thread
Process: Material experimentationConceptual modelsSolderingDrillingSewing
Furni ture Fabr icat ion
Lights Out
Designed by Allison Pell in collabo-ration with Megan Repka and Alyssa Redding
Method: Collected burnt out light bulbs ofvarious sizesCreated sphere geometryLaser cut geometry from acrylic sheets
Materials: Stainless steelLight bulbsAcrylic
Process:Rhino 3d ModelLaser-Cut Process Models