Tools Required

Part Number: G110081 Page Number: 1 of 4 Revision: D

1 Remove Data Port Cover and Blank Adapter 2

3 +Cutout Opening for Ashley Trio Bezel Assembly 4 +Install Ashley Trio Bezel Assembly into Cutout

A

1 2 3 4 5

B

C

D

E

F

A

B

C

D

1 2 3 4 5

E

F

2.19”

8.50”

SCRAP

Horizontal or Vertical

Surface

* NOTE *Max Radius on Cutout Corners is 1/4”

Thickness Range of Mounting Surface

(3/4” to 1-1/2”)

* NOTE *Tabs Point Up when Unit isInstalled Vertically - See Vertical Orientation

HorizontalSurface

Orientation

This device complies with part 15A of theFCC Rules. Operation is subject to thefollowing two conditions: (1) This devicemay not cause harmful interference, and(2) this device must accept any interferencereceived, including interference that maycause undesired operation.

Vertical SurfaceOrientations

(A)

(B)

ASHLEY TRIO BEZELHorizontal or Vertical Surface Mounting

Installation Instruction

- Corded -

Install Data Port Option (VGA, RJ45, HDMI, BLANK)

See Sheet #2 for Detailed Instructions*NOTE*

E.C.N. No: GD17-002789

2505 Dekko DriveGarrett, IN 46738Customer Service: 800.357.5622

#15 TorxScrew Driver or Wrench

All Tech Adapters Need to be Mounted in the “UP” Position. (Refer to the back of Parts)

*NOTE*

POWER AND DATA

UP

Data PortCover

BlankAdapter

UP

UP

UP

UP

UP

VGA Option

RJ45Option

HDMI Option

BLANKOption

A

B8

76

3

5e

HDMI

A

1 2 3 4 5

B

C

D

E

F

A

B

C

D

1 2 3 4 5

E

F

Tools Required

Part Number: G110081 Page Number: 2 of 4 Revision: D

This device complies with part 15A of theFCC Rules. Operation is subject to thefollowing two conditions: (1) This devicemay not cause harmful interference, and(2) this device must accept any interferencereceived, including interference that maycause undesired operation.

E.C.N. No: GD17-002789

ASHLEY TRIO BEZELHorizontal or Vertical Surface Mounting

Installation Instruction

- Corded -2505 Dekko DriveGarrett, IN 46738Customer Service: 800.357.5622

#15 TorxScrew Driver or Wrench

All Tech Adapters Need to be Mounted in the “UP” Position. (Refer to the back of Parts)

*NOTE*

POWER AND DATA

2.1 Install Data Tech Adapter Option

Tech AdapterKeystone “Universal”

(Shown)

Data PortCover

Screw#15 Torx Head

HDMITripp-LiteAllen-TelAMP TE-KroneBelden KeyConnect

Leviton Quick Port Extreme

Optical Cable Corp 5eOptical Cable Corp 6OrtronicsPanduit NetKey

Leviton Quick PortHubbell PremiseType F Coax

KEYSTONE

Belden EZ MDVO Panduit Mini-COM

Commscope Ortronics TrackJack Siemon Cable Retainer

(Universal)

(Specific) (Specific)

(Specific) (Specific)(Specific)(Specific)

HDMI(Shown)

22.2 Install VGA Connector to VGA Tech Adapters

VGAConnector VGA

Tech Adapter“Back”

VGATech Adapter

“Front”

B Install VGA Adapter Assembly into UnitVGA

Tech AdapterAssembly Screw

#15 TorxHead

2.3 Install Blank Tech Adapter Option

BlankTech Adapter

Blank

Screw#15 Torx Head

VGA Front

VGA Back

Screws

(Specific)

(Specific)

ETC. (ET. AL.)

HDMI

UP

UP UP UP UP

UPUP

UP

AUP

UP

UPUP

UP

UP

Data PortCover

Data PortCover

A

1 2 3 4 5

B

C

D

E

F

A

B

C

D

1 2 3 4 5

E

F

Tools Required

Part Number: G110081 Page Number: 3 of 4

5 Install Retainer Bracket

6 Route Power Cord Option to Nearest PowerDistribution Source

* Align Tabs on Bezel with Slotson Retainer Bracket and Slide Over

and into Engaged Position *

Mounting Surface

Back Side

* NOTE *Route Power Cord Through Hole in Retainer Bracket

* Tighten (4) Screws to SecureUnit to Worksurface *

NEMAPlug

Revision: D

This device complies with part 15A of theFCC Rules. Operation is subject to thefollowing two conditions: (1) This devicemay not cause harmful interference, and(2) this device must accept any interferencereceived, including interference that maycause undesired operation.

E.C.N. No: GD17-002789

ASHLEY TRIO BEZELHorizontal or Vertical Surface Mounting

Installation Instruction

- Corded -2505 Dekko DriveGarrett, IN 46738Customer Service: 800.357.5622

#15 TorxScrew Driver or Wrench

POWER AND DATA

A

1 2 3 4 5

B

C

D

E

F

A

B

C

D

1 2 3 4 5

E

F

Page Number: 4 of 4

8.50

”

2.19

”

+A

SHLE

Y TR

IO B

EZEL

CU

TOU

T

MA

XIM

UM

CO

RN

ER R

AD

IUS

1/4”

Part Number: G110081 Revision: D

This device complies with part 15A of theFCC Rules. Operation is subject to thefollowing two conditions: (1) This devicemay not cause harmful interference, and(2) this device must accept any interferencereceived, including interference that maycause undesired operation.

E.C.N. No: GD17-002789

ASHLEY TRIO BEZELHorizontal or Vertical Surface Mounting

Installation Instruction

- Corded -

POWER AND DATA

2505 Dekko DriveGarrett, IN 46738Customer Service: 800.357.5622