Post on 02-Aug-2015
transcript
Service Manual
Sach-Nr./Part No. 72010-019.40
Service Manual
SicherheitSafety
Sach-Nr./Part No.72010-800.00
Zusätzlich erforder-liche Unterlagenfür denKomplettservice:
Additionallyrequired ServiceManuals for theComplete Service:
Änderungen vorbehalten Printed in Germany Service Manual Sach-Nr.Subject to alteration VK 221 1196 Service Manual Part No. 72010-019.40
SERVICE MANUAL
D Btx * 32700 #
CUC 7303P 37 - 066/5 (9.21595-02 / G.CE 5602)
P 37 - 071 (9.21595-01 / G.CE 5302)
(9.21595-21 / G.CE 5902)
P 37 - 071 GB (9.21595-63 / G.CE 5502 GB)
P 37 - 731 text (9.21589-01 / G.CE 4802)(9.21589-01 / G.CE 4883)
P 37 - 731 text GB (9.21589-64 / G.CE 4902 GB)
P 45 - 731 text (9.21557-01 / G.CE 2652)
T 51 - 071 (9.21596-01 / G.CE 5275)
TP 711 (29642-062.01)TP 712 (29642-063.01)
T 51 - 720 text (9.21538-01 / G.CD 9675)
T 51 - 720 text GB (9.21538-64 / G.CD 9775 GB)
T 51 - 731 text (9.21597-01 / G.CE 5075)
T 51 - 732/5 text (9.21597-02 / G.CE 5175)
T 55 - 731 text (9.21598-01 / G.CE 6775)
(9.21598-01 / G.CE 6783)
T 55 - 731 FT GB (9.21598-64 / G.CE 7075 GB)
T 55 - 732/5 text (9.21598-02 / G.CE 6875)
T 55 - 733/5 text (9.21598-75 / G.CE 6975)
3
6
7 8 9
0 AV
P+
P–
OK
+–E R
8
+
6
+–
TP 712
VIDEO AUX P/C SAT
TXT
+–
´
54
21
Allgemeiner Teil / General Section CUC 7303
1 - 2 GRUNDIG Service
Es gelten die Vorschriften und Sicherheitshin-weise gemäß dem Service Manual "Sicherheit",Sach-Nummer 72010-800.00, sowie zusätzlichdie eventuell abweichenden, landesspezifischenVorschriften!
The regulations and safety instructions shall bevalid as provided by the "Safety" Service Manual,part number 72010-800.00, as well as therespective national deviations.
Table of Contents
Page
General Section ................................. 1-1... 1-14Technical Data ............................................................................. 1-3Module List ................................................................................... 1-5Safety Advice ............................................................................... 1-5Hints to the Components ............................................................. 1-5Hints to the Oscillograms ............................................................. 1-6Circuit Diagram Symbols ............................................................. 1-7Service Instructions (T 51-720 text GB) ..................................... 1-10Special and Service Functions ................................................... 1-13Block Circuit Diagram ................................................................ 1-14
Descriptions ...................................... 2-7... 2-121. Power Supply ........................................................................... 2-72. System Control ........................................................................ 2-83.TV Signal Processor TDA 8362 A ............................................. 2-9
3.1 Overview ......................................................................... 2-93.2 IF ..................................................................................... 2-93.3 CCVS-Signal ................................................................... 2-93.4 External CCVS Signal ..................................................... 2-93.5 Sound IF ........................................................................ 2-103.6 Luminance and Chrominance Signal ............................ 2-103.7 SECAM Signal Path
and Automatic PAL/SECAM Switching ......................... 2-103.8 RGB Signal Path ........................................................... 2-113.9 Generation of the Horizontal and Vertical Sync Signals 2-113.10 Line Oscillator ................................................................ 2-113.11 ϕ1-Phase Control .......................................................... 2-113.12. ϕ2-Phase Control .......................................................... 2-113.13. The Super Sandcastle SSC .......................................... 2-123.14 Setting of the Cut-Off Voltage ....................................... 2-123.15 HDR Output Stage ........................................................ 2-123.16 Field Deflection Stage ................................................... 2-123.17 Non-Interlace Compensation with Teletext ................... 2-123.18 Coincidence .................................................................. 2-12
Adjustments ................................................. 3-2
Layout of the PCBsand Circuit Diagrams ........................ 4-1... 4-18Chassis Board .............................................................................. 4-1Oscillograms ................................................................................ 4-7General Circuit Diagram .............................................................. 4-9CRT Panel 29305-022.16 .......................................................... 4-14CRT Panel 29305-022.14/.15 .................................................... 4-16Processing Board ....................................................................... 4-18
Spare Parts List ................................... 5-1... 5-4
GBD
Inhaltsverzeichnis
Seite
Allgemeiner Teil ................................ 1-1... 1-14Technische Daten ....................................................................... .1-3Modulübersicht ............................................................................. 1-5Sicherheitshinweise ..................................................................... 1-5Hinweise zu den Bauteilen ........................................................... 1-5Hinweise zu den Oszillogrammen ................................................ 1-6Schaltplansymbole ....................................................................... 1-7Bedienungsanleitung (T 55-731 text) ........................................... 1-8Sonder- und Servicefunktionen .................................................. 1-12Blockschaltbild ........................................................................... 1-14
Beschreibungen .................................. 2-1... 2-61. Netzteil ..................................................................................... 2-12. Systemsteuerung ..................................................................... 2-23. TV-Signalprozessor TDA 8362 A ............................................. 2-3
3.1 Übersicht ......................................................................... 2-33.2 ZF .................................................................................... 2-33.3 FBAS-Signal .................................................................... 2-33.4 Externes FBAS-Signal ..................................................... 2-33.5 Ton-ZF ............................................................................. 2-43.6 Luminanz- und Chrominanzsignal ................................... 2-43.7 SECAM-Signalweg
und automatische PAL/SECAM-Umschaltung ................ 2-43.8 RGB-Signalweg ............................................................... 2-53.9 Gewinnung der H- und V-Synchronsignale ..................... 2-53.10 Zeilenoszillator ............................................................... 2-53.11 ϕ1-Regelung ................................................................... 2-53.12. ϕ2-Regelung ................................................................... 2-53.13. Supersandcastle SSC ..................................................... 2-63.14 Cut-Off-Einstellung .......................................................... 2-63.15 HDR-Endstufe ................................................................. 2-63.16 Vertikal-Ablenkung .......................................................... 2-63.17 Non-Interlace Kompensation bei Videotext ..................... 2-63.18 Koinzidenz ....................................................................... 2-6
Abgleich ........................................................ 3-1
Platinenabbildungenund Schaltpläne ................................ 4-1... 4-18Chassisplatte ............................................................................... 4-1Oszillogramme ............................................................................. 4-7Gesamtschaltplan ........................................................................ 4-9Bildrohrplatte 29305-022.16 ....................................................... 4-14Bildrohrplatte 29305-022.14/.15 ................................................. 4-16Prozessorplatte .......................................................................... 4-18
Ersatzteilliste ....................................... 5-1... 5-4
CUC 7303 Allgemeiner Teil / General Section
GRUNDIG Service 1 - 3
Technische Daten / Technical Data
Allgemeiner Teil
Meßgeräte / MeßmittelRegeltrenntrafo Meß-/WobbelsenderFarbgenerator OszilloskopDC-Voltmeter NF-VoltmeterNF-Generator Frequenzzähler
Beachten Sie bitte das Grundig Meßtechnik-Programm, das Sie unterfolgender Adresse erhalten:
Grundig electronics GmbHWürzburger Str. 150D-90766 Fürth/Bay.Tel.0911/703-0Telefax 0911/703-4479
General Part
Test Equipment / AidsVariable isolating transformer Test/Sweep GeneratorColour Generator OscilloscopeDC Voltmeter AF VoltmeterAF Generator Frequency counter
Please note the Grundig Catalog "Test and Measuring Equipment"obtainable from:
Grundig electronics GmbHWürzburger Str. 150D-90766 Fürth/Bay.Tel.0911/703-0Telefax 0911/703-4479
P 3
7-06
6/5
P 3
7-07
1 P
37-
071
GB
P 3
7-73
1 te
xtP
37-
731
text
GB
P
45-
731
text
Bild
röhr
e / P
ictu
re T
ube
Sic
htba
res
Bild
Vis
ible
pic
ture
34cm
34cm
34cm
34cm
34cm
41cm
Bild
schi
rmdi
agon
ale
Scr
een
diag
onal
e37
cm (
14")
Tin
ted
glas
s37
cm (
14")
Tin
ted
glas
s37
cm (
14")
Tin
ted
glas
s37
cm (
14")
Tin
ted
glas
s37
cm (
14")
Tin
ted
glas
s45
cm (
17")
Bla
ck p
lana
r
Abl
enkw
inke
l D
efle
ctio
n an
gle
90°
90°
90°
90°
90°
90°
Bild
wec
hsel
freq
uenz
Ver
tical
fre
quen
cy50
Hz
50H
z50
Hz
50H
z50
Hz
50H
z
Ele
ktro
nik
/ Ele
ctro
nic
Pro
gram
msp
eich
erpl
ätze
Pro
gram
me
posi
tions
69 T
V +
1 A
V69
TV
+ 1
AV
69 T
V +
1 A
V69
TV
+ 1
AV
69 T
V +
1 A
V69
TV
+ 1
AV
AV
-Aus
wer
tung
AV
eva
luat
ion
auf j
eden
Pro
gram
mpl
atz
prog
ram
mie
rbar
/ pr
ogra
mm
able
for
ever
y pr
ogra
mm
e po
sitio
n
Kab
eltu
ner
für
Hyp
erba
nd (
8MH
z) C
able
tune
r fo
r hy
perb
and
(8M
Hz)
ja/
yes
ja/
yes
nur
UH
F/
UH
F o
nly
ja/
yes
nur
UH
F/
UH
F o
nly
ja/
yes
TV
-Nor
men
TV
sta
ndar
ds
PA
L, S
EC
AM
,N
TS
C 4
.43M
Hz
B/G
, D/K
/K'
PA
L/B
/GP
AL/ I
PA
L/B
/GP
AL/ I
PA
L/B
/G
Vid
eote
xt T
elet
ext
__
_1-
Sei
ten
Tex
t1-
page
s te
xt1-
Sei
ten
Tex
t1-
page
s te
xt1-
Sei
ten
Tex
t1-
page
s te
xt
Mus
ikle
istu
ng M
usic
pow
er2W
2W2W
2W2W
2W
Ans
chlü
sse
Rüc
kwan
d / C
onne
ctio
ns R
ear
Pan
el
Eur
o A
V (
schw
arz/
blac
k)vo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
d
Net
ztei
l / M
ains
Sta
ge
Net
zspa
nnun
g (R
egel
bere
ich)
Mai
ns v
olta
ge (
varia
ble)
165
…26
5V16
5 …
265V
165
…26
5V16
5 …
265V
165
…26
5V16
5 …
265V
Net
zfre
quen
z M
ains
freq
uenc
y50
/ 60
Hz
50 /
60H
z50
/ 60
Hz
50 /
60H
z50
/ 60
Hz
50 /
60H
z
Lei
stun
gsau
fnah
me
Pow
er c
onsu
mpt
ion
ca.
38W
ca.
38W
ca.
38W
ca.
38W
ca.
38W
ca.
50W
Sta
ndby
ca. 9
Wca
. 9W
ca. 9
Wca
. 9W
ca. 9
Wca
. 10W
Allgemeiner Teil / General Section CUC 7303
1 - 4 GRUNDIG Service
Technische Daten / Technical DataT
51-
071
T 5
1-72
0 te
xtT
51-
720
text
GB
T 5
1-73
1 te
xt
T 5
1-73
2/5
text
T
55-
731
text
T
55-
731
text
GB
T 5
5-73
2/5
text
T
55-
733/
5 te
xt
Bild
röhr
e / P
ictu
re T
ube
Sic
htba
res
Bild
Vis
ible
pic
ture
48cm
48cm
48cm
48cm
48cm
51cm
51cm
51cm
51cm
Bild
schi
rmdi
agon
ale
Scr
een
diag
onal
e
51cm
(20
")B
lack
Mat
rixsm
all n
eck
51cm
(20
")B
lack
Mat
rixsm
all n
eck
51cm
(20
")B
lack
Mat
rixsm
all n
eck
51cm
(20
")B
lack
Mat
rixsm
all n
eck
51cm
(20
")B
lack
Mat
rixsm
all n
eck
55cm
(21
")B
lack
Mat
rixsm
all n
eck
55cm
(21
")B
lack
Mat
rixsm
all n
eck
55cm
(21
")B
lack
Mat
rixsm
all n
eck
51cm
(20
")B
lack
Mat
rixsm
all n
eck
Abl
enkw
inke
l D
efle
ctio
n an
gle
90°
90°
90°
90°
90°
90°
90°
90°
90°
Bild
wec
hsel
freq
uenz
Ver
tical
fre
quen
cy50
Hz
50H
z50
Hz
50H
z50
Hz
50H
z50
Hz
50H
z50
Hz
Ele
ktro
nik
/ Ele
ctro
nic
Pro
gram
msp
eich
erpl
ätze
Pro
gram
me
posi
tions
69 T
V +
1 A
V69
TV
+ 1
AV
69 T
V +
1 A
V69
TV
+ 1
AV
69 T
V +
1 A
V69
TV
+ 1
AV
69 T
V +
1 A
V69
TV
+ 1
AV
69 T
V +
1 A
V
AV
-Aus
wer
tung
AV
eva
luat
ion
auf j
eden
Pro
gram
mpl
atz
prog
ram
mie
rbar
/ pr
ogra
mm
able
for
ever
y pr
ogra
mm
e po
sitio
n
Kab
eltu
ner
für
Hyp
erba
nd (
8MH
z) C
able
tune
r fo
r hy
perb
and
(8M
Hz)
ja
/ye
sja
/ye
snu
r U
HF
/U
HF
onl
yja
/ye
sja
/ye
sja
/ye
snu
r U
HF
/U
HF
onl
yja
/ye
sja
/ye
s
TV
-Nor
men
TV
sta
ndar
dsP
AL/
B/G
PA
L/B
/GP
AL/ I
PA
L/B
/G
PA
L, S
EC
AM
,N
TS
C 4
.43M
Hz
B/G
, D/K
/K'
PA
L/B
/GP
AL/ I
PA
L, S
EC
AM
,N
TS
C 4
.43M
Hz
B/G
, D/K
/K'
PA
L, S
EC
AM
,N
TS
C 4
.43M
Hz
B/G
, D/K
/K'
Vid
eote
xt T
elet
ext
_1-
Sei
ten
Tex
t1-
page
s te
xt1-
Sei
ten
Tex
t1-
page
s te
xt1-
Sei
ten
Tex
t1-
page
s te
xt1-
Sei
ten
Tex
t1-
page
s te
xt1-
Sei
ten
Tex
t1-
page
s te
xt1-
Sei
ten
Tex
t1-
page
s te
xt1-
Sei
ten
Tex
t1-
page
s te
xt1-
Sei
ten
Tex
t1-
page
s te
xt
Mus
ikle
istu
ng M
usic
pow
er2W
2W2W
2W2W
2W2W
2W2W
Ans
chlü
sse
Rüc
kwan
d / C
onne
ctio
ns R
ear
Pan
el
Eur
o A
V (
schw
arz/
blac
k)vo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
dvo
ll be
legt
fully
wire
d
Net
ztei
l / M
ains
Sta
ge
Net
zspa
nnun
g (R
egel
bere
ich)
Mai
ns v
olta
ge (
varia
ble)
165
…26
5V16
5 …
265V
165
…26
5V16
5 …
265V
165
…26
5V16
5 …
265V
165
…26
5V16
5 …
265V
165
…26
5V
Net
zfre
quen
z M
ains
freq
uenc
y50
/ 60
Hz
50 /
60H
z50
/ 60
Hz
50 /
60H
z50
/ 60
Hz
50 /
60H
z50
/ 60
Hz
50 /
60H
z50
/ 60
Hz
Lei
stun
gsau
fnah
me
Pow
er c
onsu
mpt
ion
ca. 5
5Wca
. 55W
ca. 5
5Wca
. 55W
ca. 5
5Wca
. 55W
ca. 5
5Wca
. 55W
ca. 5
5W
Sta
ndby
ca. 1
0Wca
. 10W
ca. 1
0Wca
. 10W
ca. 1
0Wca
. 10W
ca. 1
0Wca
. 10W
ca. 1
0W
CUC 7303 Allgemeiner Teil / General Section
GRUNDIG Service 1 - 5
GerätUnit
Chassis TunerBR-Platte
CRT PanelProzessorplatteProcessor Board
FernbedienungRemote Control
P 37-066/5 29704-002.24 8140-601-610 29305-022.14 29305-119.28 29642-062.01
P 37-071 29704-002.21 8140-601-610 29305-022.14 29305-119.28 29642-062.01
P 37-071 GB 29704-002.22 8140-601-611 29305-022.14 29305-119.28 29642-062.01
P 37-731 text 29704-002.05/.06 8140-601-610 29305-022.14 29305-119.28 29642-062.01
P 37-731 text GB 29704-002.08/.09 8140-601-611 29305-022.14 29305-119.28 29642-062.01
P 45-731 text 29704-002.01 8140-601-610 29305-022.15 29305-119.28 29642-062.01
T 51-071 29704-002.12 8140-601-610 29305-022.16 29305-119.28 29642-062.01
T 51-720 text 29704-002.04 8140-601-610 29305-022.16 29305-119.28 29642-062.01
T 51-720 text GB 29704-002.03 8140-601-611 29305-022.16 29305-119.28 29642-062.01
T 51-731 text 29704-002.04 8140-601-610 29305-022.16 29305-119.28 29642-062.01
T 51-732/5 text 29704-002.14 8140-601-610 29305-022.16 29305-119.30 29642-063.01
T 55-731 text 29704-002.07 8140-601-610 29305-022.16 29305-119.28 29642-062.01
T 55-731 FT/GB 29704-002.18 8140-601-611 29305-022.16 29305-119.28 29642-062.01
T 55-732/5 text 29704-002.16 8140-601-610 29305-022.16 29305-119.28 29642-062.01
T 55-733/5 text 29704-002.17 8140-601-610 29305-022.16 29305-119.28 29642-062.01
Modulübersicht / Module List
MetallschichtwiderständeMetal film resistorsResistenza a strato metallicoResistencia de capa metálicaFilm métallique
KohleschichtwiderständeCarbon film resistorsResistenza a strato di carboneResistencia de capa de carbónFilm carbonique
MetalloxidwiderstandMetal oxid resistorResistenza ad ossido metallicoResistencia de óxido metálicoMétaloxide
Schwer entflammbarer WiderstandFlame resistant resistorResistenza anti-infiammabileResistencia ininflamableIninflammable
Hinweise zu den Bauteilen / Hints to Components / Istruzioni sui Componenti /Observaciones sobre los Componentes / Precautions a observer
K
PTC
NTC
SI-R
SI-R
DIN 0204
DIN 0207
DIN 0414
DIN 0204
DIN 0207
DIN 0414
DIN 0617
SicherungswiderstandFuse resistorResistenza di sicurezzaResistencia con resorte de seguridadRés. fusible
Drahtwiderstand m. WattangabeWire wound resistor w. wattageResistenza a filoResistencia bobinada (Disipación)Bobinée avec ind. puissance
Heißleiter / NTC resistorTermistore NTC / Resistencia CNTVaristor (CTN)
Kaltleiter / PTC resistorTermistore PTC / Resistencia CPTVaristor (CTP)
KeramikkondensatorCeramic capacitorCondensatore ceramicoCondensador cerámicoCéramique
Kondensator, CapacitorCondensatore, CondensadorCondensador, 250 V=
+
T +
Kondensator, CapacitorCondensatore, CondensadorCondensador, 630 V=
ElektrolytkondensatorElectrolytic capacitorCondensatore elettroliticoCondensador electroliticoElectrolytique
Tantal-ElektrolytkondensatorTantalum electrolytic capacitorCondensatore elettro. al tantalioCondensador de tantalioTantale
bipolarer Elektrolytkondensatorbipolar electrolytic capacitorCondensatore elettrolitico bipolareCondensador electrolitico bipolarElectrolytique bipolaisé
Kondensator, CapacitorCondensatore, CondensadorCondensador, 400 V=
Kondensator, CapacitorCondensatore, CondensadorCondensador, 1000 V=
Sicherheits-HinweisDie in den Fernsehgeräten auftretende Röntgenstrahlung entsprichtden Bestimmungen der Physikalisch-Technischen Bundesanstaltvom 8. Januar 1987.Die Hochspannung für die Bildröhre und die damit auftretendeRöntgenstrahlung ist abhängig von der exakten Einstellung derNetzteilspannung +A.Nach jeder Reparatur im Netzteil oder in der Horizontalablenkung istdie Hochspannung zu messen und ggf. einzustellen.Schutzschaltungen im Gerät dürfen nur kurzzeitig außer Betriebgesetzt werden, um Folgeschäden am Chassis oder an der Bildröh-re zu vermeiden.Beim Austausch der Bildröhre dürfen nur die in den Ersatzteillistenvorgeschriebenen Typen verwendet werden.
Safety AdviceThe X-radiation developing in the sets conforms to the X-radiationRegulations (January 8, 1987), issued by the Physikalisch-Techni-sche Bundesanstalt (federal physiotechnical institution).The high tension for the picture tube and thus the developing X-radiation depends on the precise adjustment of the +A power supply.After every repair of the power supply unit or the horizontal deflectionstage it is imperative that the EHT for the picture tube is checked andre-adjusted if necessary.To avoid consequential damages to the chassis or the picture tubethe integrated protective circuits are allowed to be put out ofoperation only for a short time.When replacing the picture tube use only the types specified in thespare parts lists.
Allgemeiner Teil / General Section CUC 7303
1 - 6 GRUNDIG Service
Hinweise zu den Oszillogrammen / Hints to the Oscillograms / Note relative agli Oscillogr./Indications pour les Oscillogrammes / Observaciones con respecto a los Oscilogramas
D GB I F E
. . . V Gleichspannungswert / DC voltage / Valore tensione continua / Tensioncontinue / Valor de tensión continua
. . . Vss
. . . ms/cm
. . . Hz
Spitze-Spitze - Wert / Peak to peak value / Valore picco-picco / Crête-crête / Valor pico a pico
Zeitbasis des Oszilloskops / Time base of the oscilloscope / Base deltempo dell´oscilloscopio / Base de temps de l´oscilloscope/ Base detiempo del oscilocopio
Frequenz / Frequency / Frequenza / Fréquence / Frecuencia
Die Spannungswerte an den Oszillogram-men entsprechen Näherungswerten!The voltages indicated in the oscillogramsare approximates!
I valori delle tensioni indicati sugli oscillo-grammi sono approssimativi !
Les valeurs de tension indiquées pour lesoscillogrammes sont des valeurs approxi-matives!
Los valores de tensión en los oscilogramasson aproximados!
D
Servicehinweis
ChassisausbauBevor Sie die Chassis-Verbindungsleitungen lösen, muß die Leitungs-verlegung zu den einzelnen Baugruppen wie Netzschalterplatte, Bedien-einheit, Bildrohrplatte, Ablenkeinheit oder Lautsprecher beachtetwerden.Nach erfolgter Reparatur ist es notwendig, die Leitungsführung wiederin den werksseitigen Zustand zu versetzen, um evtl. spätere Ausfälleoder Störungen zu vermeiden.
NetzkabelDiese Geräte dürfen nur mit dem Original-Netzanschlußkabel mitintegrierter Entstördrossel betrieben werden. Dieses Netzkabel ver-hindert Störungen aus dem Netz und ist Bestandteil der Geräte-zulassung. Im Ersatzfall bestellen Sie bitte ausschließlich das Netz-kabel laut Ersatzteilliste.
GB
Service Note
Disassembly of the chassisBefore disconnecting the chassis connecting leads observe the waythey are routed to the individual assemblies like the mains switchpanel, keyboard control panel, picture tube panel, deflection unit orloudspeaker.On completion of the repairs the leads must be laid out as originallyfitted at the factory to avoid later failures or disturbances.
Mains cableThe TV receiver must only be operated with an original mains connectingcable with an interference suppressor choke integrated in the mainsplug.This mains cable prevents interference from the mains supply andis part of the product approval. For replacement please order exclusivelythe mains connecting cable specified in the spare parts list.
F
Information pour la maintenance
Dèmontage de chassisAvant de défaire les connecteurs du châssis princip, il y a lieu derepérer auparavant les liaisons correspondant à chaque platine commepar exemple le C.I. Inter secteur, le C.I. Commande, le C.I. Tube, lebloc déviation ou les haut-parleurs.
A la fin de l'intervention, les connexions doivent être remises dans leurposition d'origine afin d'éviter par après d'éventuelles défaillances ouperturbations.
Cable dereseauCes appareils ne peuvent être utilisés qu ' avec un cable de connecionoriginal de réseau avec bobine antiparasite intégré dans la fiche desecteur. Ce câble de réseau empêche des perturbations de réseau etest partie de l'autorisation d'appareil. Si nécessaire commandezuniquement le cable de réseau selon la liste de pièces détachées.
I
Nota di servizioSmontaggio del telaioPrima di sfilare i cavi di collegamneto col telaio è necessario osservarela disposizione originaria degli stessi verso le singole parti come lapiastra alimentazione, l'unità comandi, la piastra cinescopio, il giogo ol'altoparlante.Dopo la riparazione è necessario che gli ancoraggi e le guidegarantiscano la disposizione dei cavi analogamente a quella data infabrica e ciò per evitare disturbi o danni nel tempo.
Cavo reteGli apperechi devono essere messi in funzioni solo con il cavo originaleil colle gamento di rete e la sua spina di rete deve essere munita di unabombina d´induttanza. In causa di sostituzione ordinate solo il cavo dialimentatore che corrésponde alla lista degli accessori.
E
Nota de servicioDesmontaje del chassisAntes de desconectar las conecciones del Chassis hay que observarla dirección de dichas conecciones a los distintos grupos de construccióncomo la placa de conmutación de red, unidad de control, placa delzócalo del tubo de imagen, unidad de deflección o altavoces.Después de haber realizado la reparación y para evitar fallos opertubaciones posteriores es necesario reponer las conecciones talcomo fueron instaladas originalmente en fabrica.
Cable de redEl aparato solo se puede usar con el cable de red original con choqueantiparásito integrado en el enchufe de red. Este cable de red evitaperturbaciones de la red y es parte de la autorización del aparato. Encaso necesario puede pedir el cable de red según lista de piezas derepuestos.
CUC 7303 Allgemeiner Teil / General Section
GRUNDIG Service 1 - 7
D Schaltplansymbole GB Circuit Diagram Symbols F Symboles schéma
I Simboli sullo schema E Simbolos en los esquemas
MULTI
MULTI
INL
INL
--> Netzs
S-VHS
FR/OIRT
--> Chass
--> Abst.
FR/OIRT
--> BED
n.V.
TEXT
TEXT
GB
GB
--> BED/NS
S-VHS
37cm
37cm
OIRT
OIRT
FR
FR
NTSC
--> BR
NTSC
KH
KH
IR
IR
Netzs.
Netzs.
NOT FITTED ON PAL BG
NO EXISTE EN PAL BGMANCA NELLA VERS.PAL BGN'EXISTE PAS POUR PAL BG
ENTFAELLT BEI PAL BG
SOLAM.CON PAL BGSOLO NELLA VERS.PAL BGSEUL.POUR PAL BGONLY WITH PAL BGNUR BEI PAL BG
SOLAM.CON S-VHSSOLO NELLA VERS.S-VHSSEUL.POUR S-VHSONLY WITH S-VHS
NOT FITTED ON TELETEXTE
NUR BEI 37CM
SOLO CON OIRTSOLO NELLA VERS.OIRT
MANCA NELLA VERS.FR
N'EXISTE PAS POUR NTSC
SEUL.SI DOUILLE ECOUTEUR EST MONTE
NO EXISTE EN MULTIMANCA NELLA VERS.MULTIN'EXISTE PAS POUR MULTI NOT FITTED ON MULTI
SOLO CON MULTISOLO NELLA VERS.MULTISEUL.POUR MULTIONLY WITH MULTI
NO EXISTE EN S-VHSMANCA NELLA VERS.S-VHSN'EXISTE PAS POUR S-VHSNOT FITTED ON S-VHS
ONLY PROVIDED FOR
NOT FITED ON TELETEXT
NO EXISTE EN GB MANCA NELLA VERS.GBN'EXISTE PAS POUR GBNOT FITTED ON GB
SOLO CON GB SOLO NELLA VERS.GBSEUL.POUR GBONLY WITH GB
NO EXISTE EN FR/OIRTMANCA NELLA VERS.FR/OIRTN'EXISTE PAS POUR FR/OIRTNOT FITTED ON FR/OIRT
SOLO CON FR/OIRTSOLO NELLA VERS.FR/OIRTSEUL.POUR FR/OIRTONLY WITH FR/OIRT
NO EXISTE EN 37CMMANCA NELLA VERS.37CMN'EXISTE PAS POUR 37CMNOT FITTED ON 37CM
NO EXISTE EN OIRTMANCA NELLA VERS.OIRTN'EXISTE PAS POUR OIRTNOT FITTED ON OIRT
SOLO CON 37CM SOLO NELLA VERS.37CMSEUL.POUR 37CMONLY WITH 37CM
SEUL.POUR OIRTONLY WITH OIRT
NO EXISTE EN FR
N'EXISTE PAS POUR FRNOT FITTED ON FR
SOLO CON FRSOLO NELLA VERS.FRSEUL.POUR FRONLY WITH FR
NO EXISTE CON NTSCMANCA NELLA VERS. NTSC
NOT FITTED ON NTSC
SOLO CON NTSCSOLO CON NTSCSEUL.POUR NTSCONLY WITH NTSC
NO EXISTE CUANDO EL ENCHUFE DE AURIC.ESTA EQUIPADO
SOLO CUANDO EL ENCHUFE DE AURIC.ESTA EQUIPADO
N'EXISTE PAS SI DOUILLE EC.EST MONTENOT FITTED IF HEADPHONE SOCKET IS FITTED
ONLY WITH HEADPHONE SOCKET IS FITTED
NO EXISTE CUANDO EL RECEPTOR IR ESTA EQUIPADO
N'EXISTE PAS SI REC.IR EST MONTE NOT FITTED IF IR RECEIVER IS FITTED
SOLO CUANDO EL RECEPTOR IR ESTA EQUIPADO
SEUL.SI RECEPTEUR IR EST MONTEONLY IF IR RECEIVER IS FITTED
NO EXISTE CUANDO EL INTERR.DE RED ESTA' EQUIPADOMANCA QUANDO L'INTERR.DI RETE E' MONTATON' EXISTE PAS SI INTERR.SECTEUR EST MONTENOT FITTED IF MAINS SWITCH IS FITTED
SOLO CUANDO EL INTERR. DE RED ESTA' EQUIPADOSOLO QUANDO L'INTERR.DI RETE E' MONTATOSEUL.SI INTERR.SECTEUR EST MONTE ONLY IF MAINS SWITCH IS FITTED
A LA UNIDAD DE MANDO / PLACA INTERR.DE RED
TO CONTROL UNIT / MAINS SWITCH PANEL
ALL' UNITA DI COMANDO / PIASTRA INTERR.DI RETEVERS L'UNITE DE COMANDE/C.I.INTERR. SECTEUR
ZUR BED.-EINHEIT ODER NETZSCHALTERPLATTE
ENTFAELLT BEI MULTI
NUR BEI MULTI
ENTFAELLT BEI S-VHS
NUR BEI S-VHS
NUR BEI TEXT
ENTFAELLT BEI TEXT
NO EXISTE EN TELETEXTOMANCA NELLA VERS.TELEVIDEON'EXISTE PAS POUR TELETEXTE
SOLAM.CON TELETEXTOSOLO NELLA VERS.TELEVIDEOSEUL.POUR TELETEXTE
ENTFAELLT BEI GB
NUR BEI GB
ENTFAELLT BEI FR/OIRT
NUR BEI FR/OIRT
ENTFAELLT BEI OIRT
ENTFAELLT BEI 37CM
NUR BEI OITR
ENTFAELLT BEI FR
NUR BEI FR
A LA PLACA-ZOCALO TRCALLA PIASTRA CINESCOPIOVERS C.I. TUBE CATHODIQUETO CRT BASEZUR BILDROHRPLATTE
AL MOD.DE SINTONIAAL MOD.DI SINTONIA VERS MOD.DE SYNTH.TO TUNING MODULEZUM ABSTIMM-BAUSTEIN
A LA UNIDAD DE MANDOALL'UNITA DI COMANDOVERS L'UNITE DE COMANDETO CONTROL UNITZUR BED.EINHEIT
AL CHASISAL TELAIOVERS CHASSISTO CHASSISZUM CHASSIS
A LA PLACA INTERRUPTOR DE REDALLA PIASTRA INTERR.DI RETEVERS C.I.INTERR.SECTEURTO MAINS SWITCH BOARDZUR NETZSCHALTERPL.
SOLAM.PREVISTOSOLO PREVISTOPREVU
NUR VORGESEHEN
ENTFAELLT BEI NTSC
NUR BEI NTSC
MANCA QUANDO E' MONTATA LA PRESA CUFFIA
ENTFAELLT WENN KH-BUCHSE BESTUECKT
SOLO QUANDO E' MONTATA LA PRESA CUFFIA
NUR WENN KH-BUCHSE BESTUECKT
MANCA QUANDO L'INTERR.DI RETE E' MONTATO
ENTFAELLT WENN IR-EMPFAENGER BESTUECKT
SOLO QUANDO IL RICEVITORE IR E' MONTATO
NUR WENN IR- EMPFAENGER BESTUECKT
ENTFAELLT WENN NETZSCHALTER BESTUECKT
NUR WENN NETZSCHALTER BESTUECKT
1 - 8G
RU
ND
IGS
ervicet
Allgem
einer Teil / G
eneral Section
CU
C 7303
j8
Prog
ram
mpl
ätze
bel
egen
1. Möglichkeit
❒ ATS-Suchlauf (Auto Tuning System)Der ATS-Programme-Suchlauf tastet den gesamten Empfangsbereich abund speichert alle gefundenen Programme automatisch.Vorgehensweise:Gerät mit einer der Tasten 1 … 9 aus Bereitschaft einschalten.
Taste PC/AUX ca 4 sec. drücken bis das ATS-Menü erscheint.
Suchlauf mit Taste OK starten.Der Suchlauf-Vorgang kann über eine Minute dauern.Die Geräteeinstellung ist nun abgeschlossen.Wir wünschen Ihnen viel Spaß beim Fernsehen.
Wenn Ihnen die automatische Programmplatz-Belegung nicht zusagt, können Sie die auf den Programmplätzen gespeicherten Programme nachIhren Wünschen austauschen (umschichten).
❒ Die Dialogzeile als BedienhilfeIn der Zeile am unteren Bildrand der Menü-Einblendungen sehen Sie mitwelchen Tasten der Fernbedienung Veränderungen vorgenommen werdenkönnen.
w! Die Zeichen !, ", %%, && am Bildschirm sind Symbole für folgende Tasten derFernbedienung:%%, && = Tasten P- und P+ Bewegen des farbigen Balkens (Cursor)
nach unten/oben; bzw. Funktionsanwahl.!, " = Tasten – z und + t Bewegen des farbigen Balkens (Cursor)
nach links/rechts; bzw. Funktionsauswahl.In den Texten werden anstelle der Symbole die Tasten der Fernbedienungabgebildet.
❒ Programmplätze austauschenBeispiel: Das Programm von Programmplatz 5 soll auf Programmplatz 2.
Programmplatz 2 anwählen.
Taste i und danach OK drücken. Das Programm-Menü blendet sich ein.2
1
3
2
1
j8
Prog
ram
mpl
ätze
bel
egen
Unter »PR« neuen Programmplatz 05 mit den Tasten 1...9 eingeben.
Taste OK drücken. Der Vorgang ist abgeschlossen.
Mit Taste i zurück zum Fernsehbetrieb.
2. Möglichkeit
❒ Programmplätze manuell belegenTaste i und danach OK drücken. Das Programm-Menü blendet sich ein.
Mit Taste – z oder + t gewünschte Position wählen.
Unter»PR« mit P+/P- zu belegenden Programmplatz wählen.
»B« Bandwahl zwischen VHF1 (C2 - C4, S1 - S10), VHF3 (C5-C12, S11-S39), UHF (S40-S41, C21-C69) und ----.C = Kanal, S= Sonderkanal.Wird auf einen Programmplatz unter »B« ---- gewählt, kön-nen mit den Tasten P+ und P- alle nachfolgenden Program-mplätze nicht mehr angewählt werden.
" »TUNE« Taste P+ oder P– drücken, das Menü des manuellen Such-laufes wird eingeblendet.Wird eine der Tasten – z oder + t gedrückt gehalten, startetder Suchlauf. Der Suchlauf stoppt bei jedem Programm, dasSie empfangen können. Ist Feinabstimmen (Programmplätze1-20) notwendig, dannTaste – z oder + t kurz drücken unddamit besten Bild- und Toneindruck wählen.Mit Taste i zurück zum Programm-Menü.
" »S« Standard (Fernsehnorm) kann nicht verändert werden.
" »DEC« Wird auf diesen Programmplatz ein verschlüsseltes Pro-gramm gelegt und ein entsprechender Descrambler (Deco-der) angeschlossen, dann ist »ON« zu wählen.
Mit Taste OK die veränderten Werte speichern.
Zurückschalten ins TV-Programm mit Taste i.4
3
2
P+ PR B TUNE S DEC
w 14 UHF ➞■ 0 OFFq rr--- ■ -------- ■ -------------- ■ -------- ■ -------------------- ■ ------eeSort ➞ 0…9 OK i
1
5
4
3
i Die Dialogzeile
Hinweis:Dieses Kapitel enthält Auszüge aus der Bedienungsanleitung T 55-731 text.
Weitergehende Informationen entnehmen Sie bitte der gerätespezifischen
Bedienungsanleitung, deren Sachnummer Sie in der entsprechenden
Ersatzteilliste finden.
GR
UN
DIG
Service
1 - 9
CU
C 7303
Allgem
einer Teil / G
eneral Section
Videorecorder, Satelliten-Receiver oderDecoder (Descrambler)
❒ Anschließen
Mit einem AV-Kabel an die Buchse AV (Geräterückseite) anschließen.
❒ Bedienen des jeweils angeschlossenen Gerätes
Wiedergabe des Video-Recorders starten, bzw. SAT-Receiver einschalten.Beachten Sie bei Anschluß eines Decoders (Descrambler) das Kapitel aufSeite 4 »Programmplätze manuell belegen«.Im Menü muß beim entsprechenden Programmplatz unter »DEC« das Kürzel »ON« eingestellt sein.
❒ Anschließen mehrerer Zusatzgeräte• Bei Fernsehempfang über Kabel:
Descrambler / Videorecorder / Fernsehgerät• Bei Fernseh-Satellitenempfang:
Descrambler / Satelliten-Receiver / Fernsehgerät
w! Das Gerät entspricht den VDE-Sicherheitsbestimmungen und den Vor-schriften der Deutschen Bundespost (Zulassungs-Zeichen siehe Typenauf-kleber auf der Geräterückseite), ferner der Verordnung über den Schutz vorSchäden durch Röntgenstrahlen. Die Röntgenstrahlung – verursacht durchdie Bildröhre – ist ausreichend abgeschirmt und darum völlig ungefährlich.Beschleunigungsspannung max. 25kV/mittlerer Strahlstrom 1mA.Unsachgemäße Eingriffe, insbesondere Verändern der Hochspannung oderEinbau eines anderen Bildröhrentyps, können dazu führen, daß Röntgen-strahlung in erheblicher Stärke auftritt. So veränderte Geräte entsprechennicht mehr dieser Zulassung und dürfen nicht betrieben werden.
220-240V, 50/60Hz (Regelbereich des Netzteils 165 – 265V)Aufnahme ca. 55 W; in Bereitschaft 10 W.Tonendstufe: 2 W Musikleistung (1 W Sinus).Das Netzkabel ist im Gerät steckbar ausgeführt. Für Ersatzzwecke geben Siebitte bei der Kundendienststelle die Bestell-Nr.: 8290-991-307 an.
Änderungen und Irrtümer vorbehalten!
1
1
Ansc
hluß
mög
lichk
eite
n
j9
j9
Die
Fer
nbed
ienu
ng❒ Die Tasten der Fernbedienung0/AV…9 Programmplatz (auch AV) wählen;
Gerät aus Bereitschaft einschalten.
8 In Bereitschaft schalten.
R Helligkeit ändern.
TXT Videotext ein/aus.
E Farbkontrast ändern.
i Programmplatz-Nummer ein-/ausblenden.Videotext-Übersicht ein-/ausblenden.
+ Ton ein/aus (stummschalten).
P+, P– Programmplätze wählen;Cursor (Schreibmarke) bewegen.
P+ Gerät aus Bereitschaft einschalten.
OK Ändern und aktivieren verschiedenerFunktionen.
z – + t Lautstärke; Cursor (Schreibmarke) bewegen.
PC/AUX Vorwahltaste für verschiedeneFunktionen.Taste 4 Sekunden gedrückt haltenum ATS aufzurufen.
1 2
PC/AUX
3
4 5 6
7 8 9
0/AV TXT
P+
P–
OK
+
–
E
+
–
R
8
+
6+–
TP 711
❒ Weitere FunktionenS/W Kontrast ändern: PC/AUX drücken, dann mit + R – verändern.Sleep Timer (Ausschaltzeit 01…99 Min.) eingeben:PC/AUX drücken und danach TXT. Mit den Zifferntasten 0…9 Ausschaltzeiteingeben.w! Jeder veränderte Wert (Lautstärke usw.) wird nach ca. 8 Sekunden gespei-chert.
w! Drücken der Taste PC/AUX und danach OK schaltet wieder auf werkseitigeEinstellungen.
w! Tint hat bei diesem Gerät keine Funktion.
1 - 10G
RU
ND
IGS
ervicet
Allgem
einer Teil / G
eneral Section
CU
C 7303
Assi
gnin
g Pr
ogra
mm
e Po
sitio
ns
k10
Under ”PR”, enter the new programme position 05 with the buttons 1...9.
Press the OK button. The procedure is completed.
Press the i button to return to TV mode.
2nd possibility
❒ Assigning programme positions manuallyPres the i and then the OK button. The programme menu is displayed.
Use the – z or + t button to select the desired menu item.
Under ”PR” select the programme position to be assigned with the P+/P-button.
”B” Selct the band UHF (C21-C69) or ----.If ---- is selected under ”B”, the following programme posi-tions can no longer be selected using the P+ and P- buttons.
" ”TUNE” Press the P+ or P– button to display the manual searchmenu.Press and hold down the – z or + t button to start thesearch. The search stops at each programme which can bereceived. If finetuning is necessary (programme positions 1-20), briefly press the – z or + t button until the best picture and sound quality is obtained.Press the i button to return to the programme menu.
” ”S” The televsion standard (norm) cannot be changed.
" ”DEC” If an encoded programme is assigned to this programmeposition and an appropriate descrambler (decoder) isconnected, then select ”ON”.
Press the OK button to store the modified settings.
Press the i button to return to the TV picture.4
3
2
P+ PR B TUNE S DEC
w 14 UHF ➞■ 0 OFFq rr--- ■ -------- ■ -------------- ■ -------- ■ -------------------- ■ ------eeSort ➞ 0…9 OK i
1
5
4
3
i Dialogue line
Assi
gnin
g Pr
ogra
mm
e Po
sitio
ns
k10
1st possibility
❒ The Automatic Tuning System ATSThis automatic tuning system scans the entire reception range and auto-matically stores all found programmes.How to proceed:Switch the TV set on from standby with one of the buttons 1...9.
Press the PC/AUX button for approx. 4 sec. until the ATS menu appears.
Start the tuning system with the OK button.The station search procedure may last one minute and longer. When the station search is completed, the televsion is ready for operation.Have a good time with your new television set!
If you are not satisfied with the automatic assignment of the programmepositions, you can change the order of the programmes stored in the station positions according to your personal preferences.
❒ The dialogue line as user’s guideThe line which is displayed at the bottom of the menus shows you whichbuttons on the remote control handset are to be used to change settings.
w! The !, ", %%, && signs on the picture screen are symbols for the following buttons on the remote control handset:%%, && = P- and P+ buttons Cursor movement up/down and function
selection.!, " = z – and + t buttons Cursor movement to the left/right and
function selection.In the following text, the illustrations of the buttons instead of the symbolswill be shown.
❒ Exchanging programme positionsExample: The channel stored in programme position 2 is to be moved toprogramme position 5.
Select programme position 2.
Press the i and then the OK button. The programme menu is displayed.2
1
3
2
1
Note:This chapter contains excerpts from the operating instructions
T 51-720 text GB. For further particulars please refer to the appropriate user
instructions the part number of which is indicated in the relevant spare parts
list.
GR
UN
DIG
Service
1 - 11
CU
C 7303
Allgem
einer Teil / G
eneral Section
Conn
ectio
n Po
ssib
ilitie
s
k11
Connecting a video recorder, satellite receiveror decoder (descrambler)
❒ Connection
Connect with an AV cable to the AV socket at the back of the set.
❒ Operating the connected unit
Start playback on the video recorder or switch on the SAT receiver. Whenconnecting a decoder, observe the chapter ”Assigning programme posi-tions manually” on page 4.In the menu, ”ON” must be selected under ”DEC” for the programme posi-tion concerned.
❒ Connecting several external units• For TV reception via a cable system:
Descrambler → Video recorder → TV receiver• For satellite TV reception:
Descrambler → Satellite receiver → TV receiver
w! This unit conforms to VDE safety regulations and directives of the DeutscheBundespost (German Federal Post Office; see certification mark on the typesticker on the rear of the unit), as well as all relevant ordinances governingX-ray emissions. The picture tube, which emits X-rays, is sufficiently shiel-ded and therefore represents no danger. Accelerating voltage is max. 25 kVwith a mean beam current of 1 mA. Unauthorized tampering with the unit, in particular making adjustments tothe high voltage system, or installing a different picture tube, can consider-ably increase X-ray emissions. Units so altered no longer conform to appli-cable safety regulations and may not be operated.
220-240V, 50/60Hz (power supply control range 165 – 265V)Power consumption approx. 55 W; in standby 10 W.Sound output: 2 W music power (1 W sine power).The mains cable can be plugged into the set. If you need a replacementcable, order it at an after-sales service under the number 8290-991-307.
Subject to alterations. E. and O.E.
1
1
The
Rem
ote
Cont
rol H
ands
et
k11
❒ The remote control buttons0/AV…9 Select programme pos. (also AV);
switch on from standby..
8 Switch to standby.
R Brightness.
TXT Teletext on/off.
E Colour contrast.
i Display/suppress programme position numberDisplay/suppress Teletext overview.
+ Sound on/off (mute).
P+, P– Select programme positions;move cursor.
P+ Switch on from standby.
OK Change and activate certain functions.
z – + t Volume; move cursor.
PC/AUX Preselect button for variousfunctions.Press and hold down 4 seconds tocall up ATS.
1 2
PC/AUX
3
4 5 6
7 8 9
0/AV TXT
P+
P–
OK
+
–
E
+
–
R
8
+
6+–
TP 711
❒ Further functionsChange b/w contrast: Press the PC/AUX button then change the contrastusing the + R – button.Programme Sleep Timer (switch-off delay 01…99 min.):Press the PC/AUX and then the TXT button. Use the 0…9 buttons to enterthe switch-off delay.w! Every changed value (volume, etc.) is stored after approx. 8 sec.
w! Pressing PC/AUX and then OK recovers the factory presettings.
w! Tint has no function on this set.
Allgemeiner Teil / General Section CUC 7303
1 - 12 GRUNDIG Service
Sonder- und Servicefunktionen
1. Sonderfunktionen1.1 AnalogwertspeicherungEingestellte Analogwerte werden automatisch nach ca. 8 Sekundenoder durch Schalten in den Standby-Betrieb gespeichert.
1.2 Optimalwerte einstellen,DurchTastendruck "PC/AUX" –> "OK" werden die Optimalwerte fürHelligkeit, Kontrast, Farbstärke und Lautstärke eingestellt.
Optimalwert Maximalwert
Helligkeit 32 63Farbkontrast 32 63SW-Kontrast 50 63Lautstärke 30 63
Nach Speicherung der Minimal-Lautstärke erscheint nach Netz- oderStandby ein der OSD Lautstärkebalken für ca. 8 Sekunden als opti-scher Hinweis.
1.3 ATS StartTaste "P/C/AUX" ca. 4s gedrückt halten bis die Einblendung "ATS"(Auto Tuning System) erscheint, mit "OK" bestätigen.Das ATS-System speichert das gefundene Sendersignal automatisch(Anzeige: Kanal und Finetuning)
1.4 Maximale Programmnummer (Umkehrpunkt):Taste "6" –> "OK" drücken und die Bandwahl (B) auf einem beliebigenProgrammplatz über das Programm-Menü auf "----" stellen. Mit "OK"bestätigen und Menü beenden. Dadurch können im Programm-Modemit den Tasten "P+/P-" die nachfolgenden Programme nicht mehrfortgeschaltet werden. Liegt der Umkehrpunkt ≤ 10 ist nur eineeinstellige Programmplatzanwahl möglich.
1.5 Service-Menü aufrufen bei aktiviertem "Hotel mode on"Fernbedientaste "6" gedrückt halten und mit der Netztaste einschalten.Mit den Tasten "P+/P-" über das Menü "Hotel" anwählen und mit derTaste "V - oder + C" Anzeige auf "OFF" stellen.Bei aktiviertem "Hotel mode" ist der Aufruf des Programm-Menüs mitder Taste "PC/AUX" nicht mehr möglich.
2. Einstellungen über das Service-Menü
2.1 Service-Menü aufrufenFernbedientaste "6" gedrückt halten und mit der Netztaste einschalten.
2.2 AGC AbgleichÜber das Servicemenü "AGC ALIGN" anwählen. Einstellbar mit denTasten "V - / + C" zwischen den Werten 0…62.
2.3 OSD PositionTaste "6" auf der Fernbedienung gedrückt halten und mit dem Netz-schalter einschalten. Über das Servicemenü "OSD" (V bzw. H) an-wählen und mit den Tasten "V - / + C" die Menütafel in die Mittestellen.
2.4 Hotel Mode aktivierenÜber das Servicemenü "Hotel ON" anwählen. Bei aktiviertem "Hotelmode" ist:
Der Aufruf des Programm-Menüs mit der Taste "6" –> "OK" nichtmehr möglich.Die aktuelle eingestellte Lautstärke wird in diesem Mode als maxi-male Lautstärke gespeichert.
2.5 DecoderÜber das Servicemenü Decoder "ON" oder "OFF" schalten.Decoder "ON":Automatische Erkennung der Schaltspannung an Pin 8 der EURO-AV-Buchse (z.B. Descrambler-Betrieb bei Frankreichgeräten, oder ext.RGB-Betrieb für Italien).
2.6 ProgrammdauereinblendungZur Programmdauereinblendung die Taste "6" drücken. Nach ca. 8serscheint die Programmanzeige kleiner.
3. Einstellungen über das AUX-Menü
3.1 AUX ÜbersichtKurzzeitiger Tastendruck der Fernbedientaste "PC/AUX" ruft dasAUX–Menü auf.
3.2 Kontrastregelung aufrufenAUX-Menü aufrufen und mit Taste " R - / R + " abstimmen.
3.3 Sleeptimer aufrufenAUX-Menü aufrufen und mit der Taste "TXT" den Timer aktivieren. Mitden Zifferntasten der Fernbedienung gewünschte Abschaltzeit einge-ben und mit Taste "6" Menü beenden.
3.4 Optimalwerte für AnalogfunktionenAUX-Menü aufrufen und Taste "OK" drücken. Die Optimalwerte sindnun aufgerufen.
3.5 ATSAUX-Menü aufrufen und Taste "PC/AUX" ca. 4s gedrückt halten. ZumStarten die Taste "OK" drücken.
3.6 Tint bei NTSCAUX-Menü aufrufen und mit Taste " E - / E + " abstimmen.
CUC 7303 Allgemeiner Teil / General Section
GRUNDIG Service 1 - 13
3. Settings via the AUX Menu
3.1 AUX OverviewThe AUX menu is called up by pressing the "PC/AUX" remote controlbutton quickly.
3.2 Calling up the Contrast Setting OptionCall up the AUX menu and adjust the contrast with " R - / R +" button.
3.3 Calling up the SleeptimerCall up the AUX menu and activate the timer with the "TXT" button.Enter the desired stop time with the numbered buttons on the remotecontrol and leave the menu with button "6".
3.4 Optimum Values for Analog FunctionsCall up the AUX menu and press "OK". The optimum values are nowcalled up.
3.5 ATSCall up the AUX menu and press "PC/AUX" for approximately 4s.Press the "OK" button to start the system.
3.6 Tint with NTSCCall up the AUX menu and adjust with the button " E - / E + ".
Special and Service Functions
1. Special Functions1.1 Storing the Analog ValuesThe entered analog values are either stored automatically after approx.8 seconds or when switching to standby mode.
1.2 Setting the Optimum ValuesPressing "PC/AUX" –> "OK" the television receiver is set to theoptimum values stored for brightness, contrast, colour contrast andvolume.
Optimum Maximum
Brightness 32 63Colour contrast 32 63BW contrast 50 63Volume 30 63
Having stored the minimum volume level, the volume setting bar isindicated on the screen for approx. 8 seconds as an optical informationwhen switching the power "on" or switching on from standby.
1.3 ATS StartPress and hold the "P/C/AUX" button for approx. 4s until "ATS" (AutoTuning System) is indicated and confirm with "OK".The ATS system stores the found station signal automatically (display:channel and finetuning).
1.4 Maximum Programme Number (reversing point):Press the "6" –> "OK" buttons and enter "----" under the frequencyband selection option (B) at any programme position on the pro-gramme setting menu . Confirm with "OK" and leave the menu. As aresult of this, programme selection in programme mode with the "P+/P-" buttons is limited to the numbers lower than this position. If thereversing point is ≤ 10 only one-place programme selection is possible.
1.5 Calling up the Service Menu at "Hotel mode on"Press and hold button "6" on the remote control and switch on with themains button. With the "P+/P-" button select the "Hotel" mode in themenu and set the indication to "OFF" using the "V - or + C" button.During the time the "Hotel mode" is active it is not possible to call upthe programme setting menu with the "PC/AUX" button.
2. Settings via the Service Menu
2.1 Calling up the Service MenuPress and hold button "6" on the remote control and switch on with themains button.
2.2 AGC AlignmentSelect "AGC ALIGN" in the Service Menu. Alignment is possible inrange 0...62 with the "V - / + C" buttons.
2.3 OSD PositionPress and hold button "6" on the remote control and switch on with themains button. Select "OSD" (V or H) in the Service Menu and with the"V - / + C" buttons position the menu table in the centre of thescreen.
2.4 Activating the Hotel ModeSelect "Hotel ON" in the Service Menu. When the Hotel mode isactivated:
it is no longer possible to call up the programme setting menu withthe "6" –> "OK" buttons.the currently set volume level is stored as the maximum levelpossible in this mode.
2.5 DecoderVia the Service Menu switch the decoder "ON" or "OFF".Decoder "ON":Automatic identification of the switching voltage at Pin 8 of the EURO-AV socket (e.g. descrambler operation with TVs in French version, orexternal RGB mode for Italy).
2.6 Continuous Station Ident IndicationSo that the programme name is displayed continuously on the screenpress the "6" button. After about 8 seconds the programme is displayedin reduced size.
Allgemeiner Teil / General Section CUC 7303
1 - 14 GRUNDIG Service
FBAS/YCCVS/Y
CH
AUDIO-ZF + LautstärkeAUDIO-IF+Volume
Matrix
PAL-NTSC-Decoder
FBASCCVS
FBAS/EURO AVCCVS/EURO AV
FB
AS
SC
CC
VS
SC
RGB
RGB
RGB
Y R-YB-Y
Kontrast/ContrastHelligkeit/BrightnessFarbkontrast/Colour ContrastSperrpunktregelung/Cut-off Control
CT2821
D28
29
IC28
07
11V
Spitzenstrahlstrom-begrenzungPeak Beam Current Limiter
StrahlstrombegrenzungBeam Current Limiter
+8V
5,5MHz
20
16 UD
ATA
PE
RI
19
CT963
CT
962
CD193CT186
CT181
CT191
CD192
CD191
CR541+B
virtuelleZ-Diode
RG
B
SW/BW
45/46
11/10Tuner
AGC
BB
49
C127
1
DemodulatorKoinzidenzCoincidence
Mik
roco
mpu
ter
IC85
0
18
33
CT921 F926
5,5 TrapF924
3 8
6
5
2122…24 26 25 17 14
Audio 1
AV
MICROCOMPUTER IC850
CT916CT917
1
5051
5
13
15
CT840
Zei
lent
rafo
Line
Tra
nsfo
rmer
IC1504
7
1 3
NFAF
Drawn Switch Position = "Low" at Control Input IC150 Pin16
47
42 16
U-F
BA
S/C
CV
S
8
T68
6
+B (12V)
+8V
zur
Zei
lene
ndst
ufe
to L
ine
Out
put S
tage
37
10/36
CR686
R687
HorizontaltriggerTriggering Horizontal
CT169
CR
159
Farb
kont
rast
/ C
olou
r C
ontr
ast
Kon
tras
t / C
ontr
ast
Hel
ligke
it / B
right
ness
A
OFW F906
14311630
CIC
105B-Y
R-Y
38 SSC 5
2829
1211
16IC
110
6
Euro AV Audio
109
15161
SECAMIDENT
5
9
7
14/1SECAM-L
F931
3227
F-S
igna
l
Secam-Decoder
DelayLine
62
AV-Audio
VQ
10
AV-Audio
AMIC950
Strahlstrom-meßwiderstand/Beam Current Measurement Resistor
SW
TDA8362A
2 3
MUTE
Q172
35
Gezeichnete Schalterstellung = "Low" am Kontrolleingang IC150 Pin16
31
IC320
8
Schiebe-RegisterShift Register
CIC130
23 22 21
7,11,15
UV
Q
UD
ATA
-P
UD
ATA
CT110
12V
RGB OSD
49
11
Audio
optional
30 50 4847
Blockschaltbild / Block Circuit Diagram
CUC 7303
GRUNDIG Service 2 - 1
Schaltungsbeschreibung / Circuit Description
Beschreibung
1. Netzteil1.1 PrinzipschaltungSperrwandler können subharmonische Schwingungen aufweisen wennsie mit einem Arbeitstakt > 50% bei kontinuierlichem Induktionsstrombetrieben werden. Diese Instabilität ist unabhängig von den Eigen-schaften geschlossener Reglerkreise und wird durch die gleichzeitigeMessung der Festfrequenz und des Spitzenstroms verursacht.In Fig. 1 ist diese Erscheinung graphisch dargestellt. An t0 beginnt derEinschaltvorgang und damit steigt der Induktionsstrom mit einerSteigung m1 an. Dieser Anstieg ist eine Funktion der Eingangs-spannung im Verhältnis zur Induktanz. An t1 ist die maximale Strom-stärke erreicht, die von der Steuerspannung festgelegt ist. Dadurchwird die Sperrphase eingeleitet und der Strom fällt in einer Kurve m2 abbis zum nächsten Schwingungsvorgang. Die Instabilität läßt sichzeigen, indem man ein Störsignal zur Steuerspannung addiert. Darausergibt sich die kleine Stromänderung ∆I (gestrichelte Linie). Bei einerfesten Schwingungsdauer verkürzt sich die Sperrphase und die Mindest-stromstärke in der Leitphase (t2) erhöht sich um ∆I + ∆I m2/m1. DieMindeststromstärke beim nächsten Zyklus (t3) fällt auf (∆l + ∆l m2/m1)(m2/m1) ab. Diese Störgröße multipliziert sich mit m2/m1 bei jedemfolgenden Zyklus, so daß der Induktionsstrom beim Umschalten derPolarität abwechselnd steigt und fällt. Bis der Induktionsstrom Nullerreicht, sind mehrere Schwingungszyklen notwendig. Anschließendbeginnt der Vorgang von neuem. Ist m2/m1 größer als 1, wird derSperrwandler instabil. Addiert man zur Steuerspannung eine künstli-che Sägezahnspannung, die mit dem Pulsbreitenmodulations-Taktsynchronisiert wird, wie in Figur 1 dargestellt, verringert sich dieStörgröße ∆I in den nachfolgenden Zyklen und wird Null. Damit eineStabilität erzielt werden kann, muß die Steilheit dieser Korrektur-spannung gleich oder etwas größer als m2/2 sein. Bei einer Korrektur-spannung von m2/2 richtet sich der durchschnittliche Induktionsstromnach der Steuerspannung, so daß sich eine echte Stromregelungergibt. Die Korrekturspannung wird aus dem Oszillator abgeleitet undentweder dem Spannungsrückkopplungs- oder dem Strommeßein-gang zugeführt (Fig. 2).
Fig. 1
Fig. 2
1.2 Normalbetrieb / RegelbetriebZur Stromversorgung des Gerätes wird ein Sperrwandlernetzteil miteiner Schaltfrequenz von ca. 50kHz verwendet (bei Normalbetrieb undeiner Netzspannung von 230V).Der Kollektoranschluß des Leistungstransistors T665 liegt über derPrimärwicklung 3/1 des Sperrwandlertrafos TR601 an der gleich-gerichteten Netzspannung, D621…D624. Am Ladeelko C626 stehtbei 230V Netzspannung ca. +320V.
∆l + ∆l
m2mm
21 ∆l + ∆l m
m21
mm
21( ) )(
m1InductorCurrent
Control Voltage
∆l
t0 t1 t2 t3
Oscillator Period
(A)
t4 5t t6
∆lm1
m2
m3
InductorCurrent
Oscillator Period
Control Voltage
(B)
Die Ansteuerung sowie die Regel- und Überwachungsfunktionen desbipolaren Leistungstransistors T665 übernimmt der IC630. Die Versor-gungsspannung des Regel-ICs (Pin 7) liegt bei 12V. Nach demErreichen der Einschaltschwelle an Pin 7 über den Widerstand R633und den Kondensator C667 gibt der IC an Pin 6 einen positiven Start-Impuls (1µs) von 10Vss ab. Nach dem Anlauf des ICs wird dieVersorgungsspannung über die Diode D667 aus der Wicklung 5/7 desWandlertrafos gewonnen. Während der Leitphase des Transistorswird Energie im Übertrager gespeichert und in der Sperrphase über dieSekundärwicklung abgegeben. Der IC630 regelt an Pin 6 über dasTastverhältnis des Transistors T665 so nach, daß die Sekundär-spannungen weitgehend unabhängig von Netzspannung, Netzfrequenzund Last stabil bleiben.
Den Leistungstransistor T665 steuert ein Impulsbreitenmodulator an,der von einem im IC integrierten Oszillator getaktet wird. Die Frequenzbestimmen die Bauteile C652 und R652. Zur Stabilisierung vergleichtder IC630 die über D654 gleichgerichtete Rückkopplungsspannungmit der Referenzspannung von 5V an IC630-(8). Sinkt die Rückkopp-lungsspannung durch größere Last geringfügig, wird der Ansteuer-impuls an Transistor T665 breiter. Dadurch verlängert sich die Leitzeitvon T665, so daß mehr Energie zur Kompensation der Last übertragenwird. Am IC630-(3) liegt der Strom-Meßeingang. Zieht die Sekundär-seite zu viel Strom, wird über den Strom-Meßeingang Pin 3 dieAnsteuerung IC630-(6) des T665 unterbrochen.Bei einem Kurzschluß des Transistors T665 würde der SchaltkreisUC3842 zerstört. Deshalb verhindern die Dioden D666 und D664, daßdie Spannung an Pin 3 die Spannung von 1,2V übersteigt. Die BauteileD668, C669 und R669 arbeiten als Snaperglied.Durch die Bauteile CD654, C656, CD656 und CR656 wird ein verzö-gertes Ansteigen der Startimpulse (Soft-Start) erreicht.Mit dem Regler R654 werden die Sekundärspannungen über dieKontrolle der Spannung +A bei Helligkeit- und Kontrast-Minimumeingestellt.
1.3 Standby-BetriebIm Normalbetrieb steht am IC676-(1) (LM317) eine Spannung von ca.10,5V. Soll das Gerät in Standby geschaltet werden, setzt der µPUStandby auf "High" und damit IC676-(1) auf < 0,7V. Damit ist dieSpannung +B abgeschaltet und das Gerät schaltet in Bereitschaft.
1.4 Sekundärspannungen+A: Stromversorgung für die Horizontalendstufe aus der
Wicklung 2/10 und D682. Auf diesen Wert wird das Netz-teil eingestellt.
+33V: Die Abstimmoberspannung für den Tuner wird an derZ-Diode D683 und den Widerstand R681 aus der Wick-lung 2/10 über D682 gewonnen.
+M =16,5V Stromversorgung für die Tonendstufe aus der Wicklung6/10 und der Diode D671.
+B = 12V Stromversorgung für den Tuner und horizontale Treiber-stufe T501. Diese Spannung kommt aus der Wicklung6/10 über die Diode D671 und wird durch den ReglerIC676 stabilisiert. Abschaltung der +12V siehe "Standby-Betrieb".
+E = 8V Stromversorgung für den Bildprozessor IC150, wird imStandby-Betrieb abgeschaltet.
+H = 5V Stromversorgung für den µP IC850, InfrarotverstärkerIR810, den Tuner und CIC105.Diese Spannung steht auch in Standby an.
Zusätzlich benötigte Spannungen+D: +25V Stromversorgung für die Vertikalendstufe aus der Zeilen-
trafowicklung B/H über D444.+C: 125V Die Stromversorgung für die Bildrohrplatte wird aus der 190V Zeilentrafowicklung G/H über R543 und die Diode D543
erzeugt. 125V/14" Bildröhre; 190V/15…21" Bildröhre.
GRUNDIG Service2 - 2
CUC 7303Schaltungsbeschreibung / Circuit Description
UC 3842A
2. Systemsteuerung
2.1 MikrocomputerDer maskenprogrammierte 8-Bit-Mikrocomputer IC850(SDA5222 o.Text) decodiert die eingegebenen Tastaturbefehle, sowie die Infrarot-Fernbedienbefehle vom IR-Empfänger. Außerdem steuert er dengesamten Systemablauf und die Bildschirm-Einblendung (OSD). AlleDaten für die Programmplätze und Optionen werden in einem NVM(nichtflüchtiger Speicher) gespeichert. Der Videotext ist im SDA5252integriert.
Zur Funktion des Mikroprozessors sind folgende Grundbedingungennotwendig:- Betriebsspannung +5V/H an Pin 37- Oszillatorfrequenz 18MHz an Pin 12, 13- Reset-Impuls:
Nach jedem Einschalten mit der Netztaste wird der Prozessor anPin 15 über einen Reset-Impuls zurückgesetzt.
- I2C-Bus:Der I2C-Bus ist ein bidirektionaler Zweileiterbus, bestehend aus derSDA-Leitung (System-Daten) und der SCL-Leitung (System Clock).
Funktionskontrolle des Prozessors IC850:Die I2C-Bus Leitungen liegen über die Pull-up-Widerstände CR869und CR868 an +5V/H. Der Datenverkehr wird vom Prozessor, der denBustakt SCL erzeugt, gesteuert. Die Kontrolle der Daten- und Clock-Leitung ist im Service nur über die Messung der TTL-Pegel (L ≤ 0,8V;H ≥ 3,5V) möglich.
Service-Hinweis:Die I2C-Bus-Daten sind auch ohne Funktionsbefehl der IR-Fernbedie-nung vorhanden. Messen Sie auf der Datenleitung keine Busaktivitätenliegt evtl. ein Schluß vor. Zur Lokalisierung des Fehlers werden dannnacheinander alle am Datenbus angeschlossenen Bausteine oderBauteile abgelötet bzw. gezogen.
2.2 Initialisierung des Rechners nach dem EinschaltenNach dem Einschalten baut sich die Spannung +5V/H auf, setzt denIC850-(15) zurück und startet den Programmablauf.Mit dem Startbefehl gibt der Prozessor an Pin 40 "High" aus und dieSpannung UStandby startet das Gerät über CT826, IC676-(1) durch dieSpannungen +B, +12V (siehe Netzteil).
Nach dem Einschalten überträgt der Rechner (IC850) die Betriebsda-ten aus dem internen Speicher über den I2C-Bus an die Bus-gesteu-erten Bausteine und Schaltkreise.
InternalBias
ReferenceRegulator
Oscillator
1.0mA
ErrorAmplifier
+- +
-2R
R 1.0V
Current SenseCompartator
Gnd 5
OutputCompensation
1
2
Voltage FeedbackInput
4
8
RT
Vref
R
R2.5V
3.6VVref
UVLO
VccUVLO
Vcc 7
36V
Vcc Vin
Vc
Output
Power Ground
Current Sense Input
7
6
5
3Rs
T665
R
SQ
PWMLatch
+-
+- = Sink Only
Positive True Logic
CT
2.3 FBAS-Umschaltung Scart-BuchseHighpegel der Schaltspannung UFBAS an IC850-(16) schaltet dasFBAS-Signal FBASSC an den Ausgang Pin 19 der Scartbuchse.
2.4 BefehlseingabeDas Keyboard liegt an der Dauerspannung +5V/H. Durch Auswertungder unterschiedlichen Spannungspotentiale erkennt der ProzessorIC850-(27), -(28) den eingegebenen Tastaturbefehl.Die Fernbedienbefehle werden vom Infrarot-Empfänger IC810 ver-stärkt und an Pin 8 des µP decodiert.
2.5 Videotext IC850 (SDA5252)Im IC850 (SDA5252) ist ein 1-Seiten Videotext integriert. Die Bild-schirm-Einblendung ist in Zeilen und Spalten aufgeteilt. Zur Positionie-rung und Synchronisierung des Videotext Bildes werden demIC850-(45), (46) horizontale und vertikale Vergleichsimpulse zuge-führt. Die Aktivierung des Videotextes erfolgt intern über den I2C-Bus.Der SDA5252 tastet über Pin 30 das FBAS-Signal nach Videotext-daten ab.
2.6 OSD-EinblendungBei einer OSD-Einblendung liefert die Schaltspannung "UData",IC850-(50) "High" und schaltet IC 150-(21) ≤ 2V in den RGB-Modus.Der Zeichengenerator liefert die Einblenddaten über die Ausgangs-ports 47, 48, 49 des µP mit einer Amplitude von ca. 4,5V an die RGB-Eingänge IC150- (22), (23), (24) ca. 450mV.
2.7 Schutzschaltung U Schutz
An der Basis des Transistors T511 liegt über R511 der Fußpunkt derVertikal-Endstufe und über R512, D512, D513 der Vergleichsimpuls Faus der Horizontalendstufe. Im Fehlerfall schaltet die Basisspannungab 0,6V den Transistor durch und zieht über seinen Kollektor IC850-(32)gegen Masse. Damit schaltet der µP das Gerät in Standby.Bei Ausfall der Spannung +D fehlt am Ausgang der VertikalendstufeIC400-(5) die Gleichspannung und damit wird der Schutzschaltungs-eingang IC85 0-(32) nach Masse gezogen.Gleichzeitig liegt der Kollektor (Leitung SB) über R513, D514, CD516am Fußpunkt der Hochspannungswicklung. Bei zu hohem Strahlstromwird die Zenerspannung überschritten und zieht die Kollektorspannunggegen 0V, damit schaltet das Gerät in Standby.
CUC 7303
GRUNDIG Service 2 - 3
Schaltungsbeschreibung / Circuit Description
3. TV-Signalprozessor TDA8362A3.1 ÜbersichtBei diesem TV Konzept erfolgt fast die gesamte Verarbeitung desSignals in einem einzigen IC, dem TV Signalprozessor TDA8362A.In ihm sind integriert:
ZF-Signal:- ZF-Verstärker- Demodulator- AFC- AGC- Koinzidenzkennung
FBAS Signal:- Signalquellenumschaltung für das FBAS Signal- Luminanzverarbeitung- Farbdemodulation- Chrominanzverarbeitung- Farbkontrastregelung- RGB Matrix- C-AV Eingang- Signalquellenumschaltung für die RGB Signale- Helligkeitsregelung- Kontrastregelung- Schwarzwertregelung (Cut-off)
Ton:- Signalquellenumschaltung für den Ton- Tondemodulation- Lautstärkeregelung
Ablenkung:- Amplitudensieb- Zeilenoszillator- ϕ1 Regelung- ϕ2 Regelung- Triggerimpulsgewinnung für die Zeilenendstufe- Zeilenzähler- Sägezahngewinnung für die Vertikalablenkung- Treibersignal für die Vertikalendstufe
Zusätzlich kann der IC, je nach Beschaltung, Signale in PAL, NTSCund SECAM Norm verarbeiten.
3.2 ZFDie ZF kommt symmetrisch vom Tuner Pin 11 und 10 über das FilterF901 und das Oberflächenfilter F906. Das vom Oberflächenwellenfil-ter geformte Signal gelangt symmetrisch an die Pins 45 und 46 des
Signalprozessors. Die Demodulation des FBAS-Signals erfolgt ineinem Produktdemodulator. Der dafür benötigte DemodulatorkreisF130 liegt an Pin 2 und Pin 3. Das demodulierte Signal durchläufteinen Verstärker und steht an Pin 7 des ICs (BB). Der IC erkennt interndas Synchronsignal ohne Auftastung durch den Zeilenrückschlag-impuls. In Abhängigkeit des Synchronpegels wird eine Regelspannungerzeugt. Diese Regelspannung wirkt zunächst auf den geregeltenEingangsverstärker der ZF. Über den Pin 49 wird eine Referenz-schwelle URV eingestellt. Unterhalb dieser Schwelle wird nur derEingangsverstärker der ZF geregelt. Bei Überschreitung dieser Schwel-le wird von Pin 47 die Regelspannung Ut an den Tuner gelegt. Pin 47ist ein Open-Kollektor- Ausgang. Die Spannung beträgt im ungeregel-ten Fall etwa 5V. Erhöht sich die Eingangsamplitude, so verringertsich der AGC Pegel. Im Demodulator wird die Gleichspannung für dieAFC gewonnen. Pin 9 gibt dieses Signal als Stromausgang aus.Steigt die empfangene Frequenz, so sinkt die Regelspannung für dieAFC. Der Prozessor IC850 wertet dieses Signal aus und zieht denTuner über Finetuning nach. Aus dem demodulierten Signal wird vomSync Detektor geprüft, ob Synchronsignale vorhanden sind. Ist diesnicht der Fall, geht IC150-(4) auf "Low". Damit erkennt der ProzessorIC850-(33) die fehlende Koinzidenz und schaltet den Ton stumm.
3.3 FBAS SignalDas demodulierte FBAS Signal verläßt den IC150-(7), TDA8362A alsBasisband noch gemeinsam mit der Ton ZF. Das FBAS Signal wird imweiteren Verlauf vom Tonsignal befreit. Nach dem Transistor CT921und dem Ton-Trap F923 und F924 wird das Signal aufgeteilt.Über Transistor CT110 und IC2807 (Option) steht es als FBASSC amVideotext-Decoder IC850-(30) und über die Transistoren CT963,CT962 an der Scartbuchse Pin 19.Als FBAS steht es am Signalquellenumschalter IC150-(13).Der zweite Eingang des Signalquellenumschalters Pin 15 ist mit derScartbuchse Pin 20 verbunden.Der Prozessor IC850-(42), Spannung UVQ, Transistor CT840 trifft anIC150-(16) die Auswahl, ob das Signal vom Tuner oder von externverarbeitet werden soll.
3.4 Externes FBAS-SignalAm Signalquellenumschalter IC150-(15) steht entweder ein externesFBAS-Signal von der Scart-Buchse oder das HF-FBAS-Signal. DieSpannung UVQ an IC150-(16) wählt aus, ob das FBAS-Signal derScart-Buchse, oder das HF-FBAS-Signal weitergeleitet werden soll.IC150-(16) "Low" internes -, IC150-(16) "High" externes Signal.Achtung: Ist die "Decoder Ein" Kennung gesetzt, erwartet das Gerätein Signal von der Scart-Buchse. Das FBAS-Signal vom Tuner ist aberam Ausgang Pin 19 der Scartbuchse meßbar.
Bild ZF und DemodulationVision IF and Demodulation
FBAS und TonAusgangCCVS and SoundOutput
F130
ZF vom TunerIF from Tuner
Ufür denTunerfor the Tuner
URV vom Prozessorfrom Processor
AFC
KoinzidenzCoincidence
SyncDetector
TDA8362A~
45
46
2 3
47
49
9
4
7
~
GRUNDIG Service2 - 4
CUC 7303Schaltungsbeschreibung / Circuit Description
nun die Farbkomponentensignale demoduliert und verlassen als R-YPin 30 und B-Y Pin 31 den IC150. Nach der PAL-Verzögerung durchden CIC105 TDA4665 werden die beiden Signale B-Y und R-Y wiederin den IC150-(28), -(29) TDA8362 A eingespeist und geklemmt.Anschließend erfolgt die Regelung des Farbkontrastes an IC150-(26).In der Matrix werden aus den verstärkten Signalen mit Hilfe desY-Anteils die RGB-Signale erzeugt.
3.7 SECAM-Signalweg und automatische PAL-SECAM-UmschaltungDas Chromasignal von ca. 300mV steht für den SECAM-IC110 anIC150-(27).Im SECAM-Betrieb steht an IC110-(16) eine Spannung von 5,6…5,8VHat der IC110 über das Chromasignal an Pin 16 SECAM erkannt, wirdan Pin 1 eine Stromquelle aktiviert, die an IC150-(32) SECAM-Identifikation meldet. Erkennt IC150 ebenfalls SECAM , schaltet er denPin 32 auf 5V (bei PAL 1,5V). Dieser Gleichspannung wird bei PALeine gleichmäßige Taktfrequenz und bei SECAM Impulspakete miteiner Frequenz von 4,43MHz überlagert.Der IC110 nimmt dies als Bestätigung an und schaltet die Differenz-Signalausgänge R-Y und B-Y (Pin 9 und 10) auf 3,5V DC (beiPAL 1,5V). Die Differenzsignalausgänge des IC150-(30), -(31) wer-den dadurch gesperrt. IC110 liefert jetzt R-Y und B-Y. Über dieLaufzeitleitung CIC105 gelangen die Differenzsignale zurück zumIC150. Der weitere Verlauf der Signale ist unter 3.6 "Luminanz undChrominanz Signal" beschrieben.Bei SECAM-Empfang wird der DC-Pegel 3,5V an IC110-(10). ÜberCT115 wird UPAL "Low" (PAL="High") und der µP IC850-(1) kann beiATS-Suchlauf PAL oder SECAM-Empfang erkennen (nur Frankreich).Bei OIRT-Empfang (6,5MHz Tonträger) schaltet CT915 über UAUDIO
und CT115 den Suchlaufmodus des µP (UPAL) um.
3.5 Ton-ZFDem Tonsignal ist nach dem Keramikfilter F926 an IC150-(5) eineGleichspannung zur Einstellung der Lautstärke unterlegt. DieDemodulation erfolgt in einem PLL Demodulator.Einmal wird das demodulierte und ungeregelte NF Signal an IC150-(1)ausgekoppelt, von den Transistoren CT917, CT916 verstärkt und zurScart-Buchse geleitet.Zum anderen steht das demodulierte und geregelte NF-Signal anIC150-(50) und gelangt zum NF-IC TDA7233.
3.6 Luminanz- und Chrominanz-SignalDie Kalibrierung und Regelung erfolgt automatisch während derBildaustastlücke. Eine Änderung der Einstellung resultiert aus einempositiven oder negativen Strom in den Integrationskondensator CC177an IC150-(12). Während des sichtbaren Teils wird die Regelunggeklemmt.Das Luminanzsignal durchläuft den im IC integrierten Farb-Trap. Eineim IC eingebaute Verzögerungsleitung kompensiert die Laufzeitunter-schiede zwischen Luminanz- und Chrominanzsignal. Die anschlie-ßende Verbesserung der Kantenschärfe (Peaking) wird ebenfalls imIC realisiert. Dabei werden die ansteigenden und abfallenden Flankendes Y-Signals versteilert. Im internen Farbfilter wird das Chrominanz-signal aus dem FBAS-Signal herausgefiltert. In einem Regelkreis wirddie Amplitude des Farbsignals für den Farblimiter und die Farbregelungkontrolliert und gelangt als Chromasignal auf den Farbdemodulator.Aus dem Chromasignal wird der Burst herausgelöst, der denFarboszillator in Frequenz und Phase synchronisiert. Der Quarz legtdie Frequenz von 4,43MHz für den Farbhilfsträger an Pin 35 fest. Eininterner PLL-Kreis regelt ihn. Die Nachregelspannung wird über dieZeitkonstante an Pin 33 integriert. Mit Hilfe des Farbträgers werden
Ton ZF und DemodulationSound IF and Demodulation
Ton ZF +Lautstärkeregelung
Sound IF +Volume Control
HPFPLL
Demodulator
LPF
Ungeregelter Ton ScartUncontrolled Sound to Scart
Deemphasis
Geregelter TonControlled SoundTon von Scart
Sound from Scart
Schaltsignal vomProzessor
Switching Signalfrom Processor
5
6
16
50
1
LPF
Filterung des Luminanz- und ChrominanzsignalsLuminance and Chrominance Filter
Schaltsignal vom ProzessorSwitching Signal from Processor
FBAS von HFCCVS form RF
FBAS von ExternExternal CCVS
Regelspannung für die CalibrierungControl Voltage
for Calibration
CH
Y
16
13
15
12
Farb-TrapColour Trap
Delay Peaking2dB
Autom.Calibrierung
Auto Calibration
Farb-FilterChroma Filter
Farb-LimiterFarb-Regler
Chroma LimiterChroma Control
CUC 7303
GRUNDIG Service 2 - 5
Schaltungsbeschreibung / Circuit Description
3.8 RGB-SignalwegFür die Kontrasteinstellung der RGB-Signale erzeugt der IC850-(23)eine variable Regelspannung für den Kontrastverstärker an IC150-(25).Da bei zu großem Strahlstrom die Bildröhre beschädigt werdenkönnte, begrenzt die Schaltung den Strahlstrom. Die interneSpitzenstrahlstrombegrenzung erfolgt in der Spitzenweiß-Begren-zung. Überschreitet das RGB-Signal 2,3Vss, setzt die interne Spitzen-weiß-Begrenzung ein und regelt den Kontrast zurück, die externeSpitzenstrahlstrom-Begrenzung setzt bei ca. 2Vss ein.Bei der mittleren Strahlstrombegrenzung wird die Einstellspannung anIC150-(25) für Kontrast verringert.Nach dem Helligkeitsverstärker verlassen die RGB-Signale den IC150und gelangen zu den Kathodenverstärkern auf der Bildrohrsockel-platte.
3.9 Gewinnung der H- und V-SynchronsignaleAm TV-Signalprozessor IC150-(13), -(15) ist das FBAS-Signal von derZF und der EURO-AV-Buchse angeschlossen. Nachdem ein internerFarbtrap die Farbinformationen aus dem FBAS-Signal herausgefilterthat, wird das Y-Signal zur weiteren Signalverarbeitung und für dasAmplitudensieb aufgeteilt.Das Amplitudensieb erzeugt den Horizontal- und Vertikalsynchron-impuls aus dem Y-Signal. Das Horizontal-Synchronsignal gelangt nun
auf die ϕ1-Regelung, das Vertikal-Synchronsignal startet den Zeilen-zähler für die Vertikalsynchronisation.
3.10 ZeilenoszillatorBei diesem IC-Konzept generiert der Zeilenoszillator die Zeilenfrequenzvollständig intern. Er besitzt keine externen Bauteile. Somit sind wederdie freilaufende Horizontal- noch die freilaufende Vertikalfrequenzeinzustellen.
3.11 ϕ1-RegelungDie ϕ1-Regelung stellt eine Frequenzregelung dar. Damit wird derHorizontal-Oszillator auf die Frequenz des Zeilensynchronsignalsgeregelt. Hierzu wird die Frequenz des Zeilensynchronsignals mit derFrequenz des Horizontal-Oszillators verglichen.Ein ϕ1-Regelkreis definiert die Zeitkonstante der Regelspannung, diean IC150-(40) ausgegeben wird. Die Regelspannung verschiebt denZeilenoszillator solange, bis die Frequenzen übereinstimmen.
3.12 ϕ2-RegelungDie ϕ2-Regelung ist die Phasenregelung. Sie stellt den Phasenbezugzwischen dem Zeilensynchronsignal und der tatsächlichen Positiondes Elektronenstrahls her. Schaltungs- und strahlstrombedingt beste-hen unterschiedliche Verzögerungszeiten zwischen dem Außen-,dem Triggersignal und der tatsächlichen Reaktion der Zeilenendstufe.Diese Unterschiede werden durch die ϕ2-Regelung ausgeglichen.
RGB AusgangsverstärkerRGB Output Amplifier
RGB internInternal RGB
RGB von Scartoder Videotext
RGB from Scartor Videotext
Data KontrastContrast
HelligkeitBrightness
RGB externExternal RGB
RGB zur BildrohrplatteRGB to the CRT panel
SpitzenweißBegrenzungPeak White
Limiting
222324
21 25 17
201918
Chroma-Signal
35
Farbkontrast vomProzessor
Colour Contrastfrom Processor
LuminanzsignalLuminance Signal
BurstPLL
(R-Y)
(B-Y)
(R-Y)
(B-Y)
Delay
Delay
RGBMatrix
R
G
BY
+
+
33
26
30
31
4,43MHz4,43MHz
34
3,58MHz
Farb-OszillatorColour Oscillator
29
28
H/2PAL-SchalterPAL Switch
TDA4662TDA4665 (OIRT/FR)
FarbdemodulationColour Demodulation
GRUNDIG Service2 - 6
CUC 7303Schaltungsbeschreibung / Circuit Description
Für die Strahlposition ist der Zeilenrückschlagimpuls vom Zeilentrafoam IC150-(38) angeschlossen. Die ϕ2-Regelung erzeugt aus demOszillatorsignal und dem Zeilenrückschlagimpuls eine Regelspannungam IC150-(39), die mit CC166 gesiebt wird.
3.13 Supersandcastle SSCDas 3-pegelige Supersandcastlesignal IC150-(38) ist ein Kombi-Impuls bestehend aus dem Horizontal- Vertikal- und Burstauftastimpuls.Der Zeilenrückschlagimpuls (H-Sync) wird über T523, CR163 demIC150 zugeführt. Die Bildrückschlag- und Burstkeyimpulse werden imIC generiert.Bei Ausfall der Vertikalablenkung zieht IC400-(7) den SSC-Pegel überR401 auf "Low" und steuert an IC150-(18), -(19), -(20) RGB denBildschirm dunkel. Dabei werden die Analogwerte auf "Low" gezogen.
3.14 Cut-Off-EinstellungDie statischen Arbeitspunkte der Bildröhre werden über die Cut-Off-Automatik stabil gehalten. Dazu gibt der IC150 in der Zeile 23, 24 und25 einen Impuls an die R, G, B-Kathoden aus, um den Strahlstromjedes Systems zu messen (ca. 10µA). Der Cut-Off-Strom während derMeßzeilen wird über Widerstand CR156 dem IC150-(14) zugeführt.Der IC vergleicht diesen Strom mit einem internen Referenzwert undbildet daraus den Arbeitspunkt für den Schwarzwert der Videoendstufenbzw. Cut-Off Spannung der Bildröhre.
3.15 HDR-EndstufeNach interner Verstärkung steht an Pin 37 das Horizontale Ansteuer-signal für den Zeilenendstufentransistor.
3.16 Vertikal-AblenkungDer Vertikal-Generator wird in diesem IC-Konzept durch einen Zeilen-zähler ersetzt.Werden keine Synchronimpulse empfangen, so läuft der Zeilen-oszillator unsynchronisiert. Aus dem Zeilenoszillator leiten wir den
"Vertikaloszillator" ab. Es muß nur die Anzahl der Zeilen gezähltwerden. Nachdem der Zähler 312 Zeilen festgestellt hat, wird einBildsynchronsignal ausgegeben. Damit ist sowohl die horizontale alsauch die vertikale Ablenkung ohne externe Synchronisation sicherge-stellt.Wird ein Synchronsignal empfangen, dann läuft zunächst der Zeilen-oszillator synchron. Der Zeilenzähler liefert auch hier ein vertikalesAblenksignal. Kommt nun ein Vertikalsynchronsignal, wird derSägezahngenerator nicht mehr vom Zeilenzähler sondern direkt vomVertikalsynchronsignal getriggert .Der Sägezahngenerator besteht aus einer Konstantstromquelle, dieeinen externen Kondensator auf- und wieder entlädt. Die Ladezeit gibtdas Vertikalsynchronsignal vor. Am Kondensator C158, IC150-(43) istder Vertikal-Ablenksägezahn meßbar.Um die Bildhöhe in der Vertikalendstufe IC400 einstellen zu können,muß der Ablenksägezahn beeinflußt werden. Die Veränderung desAblenksägezahns muß noch vor der Vertikalendstufe durchgeführtwerden. Dazu steht an IC150-(42) von dem IC400 ein Feedback-Signal zur Gegenkopplung. Wie bei einem Operationsverstärker aufdem Minuseingang lassen sich dadurch die gewünschten Parametereinstellen.
3.17 Non-Interlace Kompensation bei Videotext (25Hz Modulation)Wird ein Videotext-Signal dargestellt, springt das Videotext-Signalständig um eine Zeile rauf und runter (Videotext-Signal im Non-Interlace). Um dieses Springen zu verhindern, sendet der Videotext-IC850-(52) ein 25Hz Schaltsignal an IC150-(43). Aus dieser Schalt-spannung U25Hz wird ein kleiner Gleichspannungs-Offset für den Ab-lenksägezahn abgeleitet. Damit verschiebt sich das erste Halbbildnach oben. Die geraden und die ungeraden Zeilen werden nun jeweilsübereinandergeschrieben.
3.18 KoinzidenzDie Koinzidenz-Information wird im ZF-Teil gewonnen und am IC150-(4)ausgegeben.
ZeilenoszillatorLine Oscillator
25 Hz
FBAS
CCVS
AmplitudensiebSync Separator
ϕ 1
ZeilenzählerLine Counter
V-Sync
H-Sync
ϕ 2 HDR
+
-VDR
SB VFB
40 36
Enable OszillatorEnable Oscillator
38 39Regelzeitkonstante für die ϕ 1-Regelung
Regelzeit-konstante für die ϕ 2-Regelung
Control Time Constantfor ϕ 2-Control
Flyback
37
43 42
44
Control Time Constantfor ϕ 1-Control
H/V-Synchronisation und AblenkungH/V Synchronisation and Deflection
CUC 7303
GRUNDIG Service 2 - 7
Schaltungsbeschreibung / Circuit Description
Description
1. Power Supply
1.1 Basic CircuitCurrent mode converters can exhibit subharmonic oscillations whenoperating at a duty cycle greater than 50% with continuous inductorcurrent. This instability is independent of the regulators closed loopcharacteristics and is caused by the simultaneous operating condi-tions of fixed frequency and peak current detecting.Figure 1 shows the phenomenon graphically. At t0, switch conductionbegins, causing the inductor current to rise at a slope of m1.This slopeis a function of the input voltage divided by the inductance. At t1, theCurrent Sense Input reaches the threshold established by the controlvoltage. This causes the switch to turn off and the current to decay ata slope of m2, until the next oscillator cycle. The unstable condition canbe shown if a pertubation is added to the control voltage, resulting ina small ∆l (dashed line). With a fixed oscillator period, the current decaytime is reduced, and the minimum current at switch turn-on (t2) isincreased by ∆l + ∆l m2/m1. The minimum current at the next cycle (t3)decreases to (∆l + ∆l m2/m1) (m2/m1). This pertubation is multiplied bym2/m1 on each succeeding cycle, alternately increasing and decreas-ing the inductor current at switch turn-on. Several oscillator cycles maybe required before the inductor current reaches zero causing theprocess to commence again. If m2/m1 is greater than 1, the converterwill be unstable. Figure 1 shows that by adding an artificial ramp thatis synchronized with the PWM clock to the control voltage, the ∆lpertubation will decrease to zero on succeeding cycles. This compen-sating ramp (m3) must have a slope equal to or slightly greater thanm2/2 for stability. With m2/2 slope compensation, the average inductorcurrent follows the control voltage yielding true current mode opera-tion. The compensating ramp can be derived from the oscillator andadded to either the Voltage Feedback or Current Sense inputs (Figure 2).
Fig. 1
Fig. 2
1.2 Normal / Controlled OperationFor the power supply of this TV receiver a blocking oscillator-typeconverter power supply with a switching frequency of 50kHz approxi-mately is used (at normal operation and a mains voltage of 230V).The collector contact of the power transistor T665 is connected via theprimary winding 3/1 of the blocking oscillator-type transformer TR601to the rectified mains voltage, D621…D624. At a mains voltage of 230Vthe voltage level present at the charging electrolytic capacitor C626 isapprox. +320V.
∆l + ∆l
m2mm
21 ∆l + ∆l m
m21
mm
21( ) )(
m1InductorCurrent
Control Voltage
∆l
t0 t1 t2 t3
Oscillator Period
(A)
t4 5t t6
∆lm1
m2
m3
InductorCurrent
Oscillator Period
Control Voltage
(B)
The IC630 is responsible for driving, controlling and monitoring thebipolar power transistor T665. The supply for the control-IC is 12V andis present on Pin 7. As soon as the switch-on threshold is reached onPin 7 via the resistor R633 and the capacitor C667, the IC feeds out apositive start pulse (1µs) of 10V pp at Pin 6. After start-up of the IC, thesupply voltage is obtained via the diode D667 from the winding 5/7 ofthe transformer. During the conducting phase of the transistor, energyis stored in the transformer and this is transferred into the secondarywinding when the transistor is switched off. The IC630 controls by theperiod during which the transistor T665 is switched on, the transfer ofenergy at Pin 6 so that the secondary voltages are stable and arelargely not affected by variations of the mains supply, mains frequencyand the load.
The power transistor T665 is driven by a pulse-width modulator whichis triggered by an oscillator integrated in the IC. The frequency of theoscillator is determined by the components C652 and R652. Forstabilisation, the feedback voltage which is rectified by D654 iscompared in IC630 with the 5V reference voltage provided at IC630-(8).If the feedback voltage decreases by a small amout due to a heavierload the drive pulse to the transistor T665 is prolonged. As a result, theconducting period of T665 will be longer so that additional energytransfer will be provided to compensate for the load. Pin 3 of IC630 isa current sense input and will stop the drive to T665 at IC630-(6) in theevent of excessive current drain from a heavy secondary load.If there was a short circuit condition at the transistor T665, the circuitUC3842 would be destroyed. Therefore, the diodes D666 and D664are provided to avoid the voltage at pin 3 exceeding 1.2V. Thecomponents D668, C669, and R669 work as a snap stage.The components CD654, C656, CD656, and CR656 delay the rise ofthe pulse start duration (soft start).The adjustment control R654 is used to set the secondary voltages byregulating the +A voltage at minimum brightness and contrast.
1.3 Standby ModeIn normal operating mode, a voltage of approx. 10.5V is present onIC676-(1) (LM317). If the TV receiver is to be switched to standby, theµP switches U
Standby to "High" level so that the level on IC676-(1) is
< 0.7 V. As a result, the voltage +B is switched off and the TV receivergoes to standby.
1.4 Secondary Voltages+A: Supply for the horizontal output stage from the winding
2/10 and D682. The power supply unit is set to this level.+33V: The upper tuning voltage limit for the tuner is produced at
the Z-diode D683 and the resistor R681 from the winding2/10 via D682.
+M =16.5V Supply for the sound output stage from the winding 6/10and the diode D671.
+B = 12V Power supply for the Tuner and the horizontal driver T501.This voltage is supplied from the winding 6/10 via the diodeD671 and is stabilised by the adjustment control IC676.Switching off of the +12V supply, see "Standby Opera-tion".
+E = 8V Power supply for the Video Processor IC150. In Standbymode it is switched off.
+H = 5V Power supply for the µP IC850, the infrared amplifierIR810, Tuner, and CIC105.This voltage is also present in Standby mode.
Additionally necessary voltages+D: +25V Power supply for the vertical output stage from the line
transformer winding B/H via D444.+C: 125V The power supply for the picture tube panel is obtained 190V from the line transformer winding G/H via R543 and the
diode D543. 125V/14" CRT; 190V/15…21" CRT.
GRUNDIG Service2 - 8
CUC 7303Schaltungsbeschreibung / Circuit Description
2. System Control
2.1 MicrocomputerThe mask-programmed 8-bit Microcomputer IC850 (SDA5222 withoutText) decodes the commands entered on the keyboard and also theinfra-red remote control commands from the IR-receiver. It is alsoresponsible for the total system control and the on-screen display(OSD). All data for the programme positions and the options are storedin the NVM (Non Volatile Memory). The teletext (Videotext) IC isintegrated in SDA5252.
The correct operation of the microcomputer depends on the followingconditions:- Supply voltage +5V/H at Pin 37- Oscillator frequency 18MHz at Pins 12, 13- Reset pulse:
Every time the TV receiver is switched on with the mains button, theprocessor is reset on Pin 1 by the reset pulse.
- I2C-bus:The I2C-bus is a bidirectional two-lead bus consisting of the SDA(System Data) lead and the SCL (System Clock) lead.
Checking the operation of the processor IC850:The I2C-bus leads are connected via the pull-up resistors CR869 andCR868 to +5V/H. The data traffic is controlled from the processor whichalso generates the SCL bus clock. The only way to check the data andclock leads when servicing is by measuring the TTL-levels (L ≤ 0.8V;H ≥ 3.5V).
Service note:The I2C-bus data is also present without a command from the IRremote control handset. If no data is carried on the bus leads there maybe a short circuit. To localize the fault, the modules and componentsconnected to the data bus must be unsoldered or unplugged one afterthe other.
2.2 Initialisation of the Processor after Switching OnWhen the TV is switched on, the +5V/H voltage builds up, theIC850-(15) is reset, and the programme sequence is started.With the start command, the processor feeds out a "High" level atPin 40 and the voltage UStandby starts the TV via CT826, IC676-(1) bymeans of the voltages +B, 12V (see Power Supply).
After switching on, the processor (IC850) transfers the operating datafrom the internal memory via the I2C-bus to the bus-controlled modulesand circuits.
InternalBias
ReferenceRegulator
Oscillator
1.0mA
ErrorAmplifier
+- +
-2R
R 1.0V
Current SenseCompartator
Gnd 5
OutputCompensation
1
2
Voltage FeedbackInput
4
8
RT
Vref
R
R2.5V
3.6VVref
UVLO
VccUVLO
Vcc 7
36V
Vcc Vin
Vc
Output
Power Ground
Current Sense Input
7
6
5
3Rs
T665
R
SQ
PWMLatch
+-
+- = Sink Only
Positive True Logic
CT
2.3 Switching over of the CCVS Signals to the Scart SocketA "High"-level switching voltage UFBAS at IC850-(16) causes the CCVSsignal FBASSC to be switched to output pin 19 of the Scart socket.
2.4 Entering CommandsThe keyboard is connected to the unswitched voltage +5V/H. Byevaluating the different voltage levels, the processor IC850-(27),-(28)knows which button on the keyboard has been pressed.The remote control commands are amplified by the infrared receiverIC810 and decoded at Pin 8 of the microprocessor.
2.5 Teletext IC850 (SDA5252)The IC850 (SDA5252) contains a 1-page Teletext-IC. The On ScreenDisplay is subdivided into lines and columns. For positioning andsynchronising the teletext display, horizontal and vertical referencepulses are fed to IC850-(45, 46). Activation of the teletext is effectedinternally via the I2C-bus. Via pin 30, the SDA5252 scans the CCVSsignal for teletext data.
2.6 On Screen Display (OSD)For displaying data on the screen, the switching voltage "UData"IC850-(50) supplies a "High" level switching IC150-(21) ≤ 2V to RGBmode. The character generator feeds out the display data via theoutput ports 47, 48, 49 of the microprocessor at an amplitude of 4.5Vto the RGB inputs IC150-(22), -(23), -(24), approx. 450mV.
2.7 Protection Circuit U Schutz
The base of the transistor T511 is connected via R511 to the low-endpoint of the vertical output stage, and via R512, D512, D513 to thereference pulse F from the horizontal output stage. In the case of anyfailure, a base voltage of 0.6V and higher switches the transistor on; viaits collector the transistor switches IC850-(32) to ground. The µP thenswitches the TV to standby.If the voltage +D fails there is no direct voltage present at the output ofthe vertical output stage IC400-(5) and consequently the proctectioncircuit input IC850-(32) is pulled to ground.At the same time the collector (SB lead) is connected via R513, D514,and CD516 to the low-end point of the high-tension winding. When theZener voltage is exceeded due to too high a beam current the collectorvoltage decreases to 0V so that the TV switches to standby.
UC 3842A
CUC 7303
GRUNDIG Service 2 - 9
Schaltungsbeschreibung / Circuit Description
3. TV Signal Processor TDA8362A3.1 Overview:With this TV design the whole signal processing is carried out in asingle IC, i.e. the TV Signal Processor TDA 8362A.It accommodates the following stages:
IF Signal:- IF amplifier- Demodulator- AFC- AGC- Coincidence identification
CCVS Signal:- Signal source switch for the CCVS signal- Luminance processing- Colour demodulation- Chrominance processing- Colour contrast control- RGB matrix- C-AV input- Signal source switch for RGB signals- Brightness control- Contrast control- Black level control (cut-off)
Sound:- Signal source switch for the sound- Sound demodulation- Volume control
Deflection:- Sync separator- Line oscillator- ϕ1 phase control- ϕ2 phase control- Trigger pulse generation for the line output stage- Line counter- Saw-tooth generation for the vertical deflection- Drive signal for the field output stage
Dependent on the associated circuitry, the IC is also able to processPAL, NTSC and SECAM signals.
3.2 IFThe IF spectrum of frequencies is fed through a symmetrical path fromthe tuner Pins 11 and 10 via the filter F901 and the Surface AcousticWave filter F906. The signal formed by the Surface Acoustic Wave filteris applied symmetrically to Pins 45 and 46 of the signal processor. Thedemodulation of the CCVS signal is carried out in a product demodulator.
The required demodulator circuit F130 is connected to Pin 2 and Pin 3.The demodulated signal passes through an amplifier and is thenpresent at Pin 7 of the IC (BB). The IC identifies the synchronisingsignal internally and for this reason, feedback of the line flyback pulsefor gating purposes is not necessary. Corresponding to the synchron-ising signal level a control voltage is generated. This control voltagefirst acts on the controlled input amplifier of the IF. Via Pin 49 areference threshold URV is set. Below this threshold, only the inputamplifier of the IF is regulated. If the threshold is exceeded, the controlvoltage Ut is applied from Pin 47 to the tuner. Pin 47 is an open collectoroutput. In uncontrolled condition, the voltage is approximately 5V. Withincreasing input amplitude the AGC level decreases. The directvoltage for automatic frequency control (AFC) is generated in thedemodulator. Pin 9 feeds out this signal as a current signal. When thereceived frequency increases the control voltage for AFC decreases.The processor IC850 evaluates the signal and fine tunes the tuneraccordingly. The demodulated signal is examined by the sync detectorfor the presence of synchronising signals. If no such signals arepresent, the IC150-(4) switches to "Low". By this level the processorIC850-(33) can identify that the coincidence signal is missing andmutes the sound.
3.3 CCVS SignalThe demodulated CCVS signal leaves IC150-(7), TDA8362A, as abaseband signal together with the sound-IF. In the following path, thesound signal is separated from the CCVS signal. After the transistorCT921 and the sound trap F923 and F924 the signal path divides.Via the transistor CT110 and IC2807 (optionally) it is fed through to thevideotext decoder IC850-(30) as FBASSC signal, and via the transistorsCT963, CT962 it is supplied to the Scart socket pin 19.At the signal source switch IC150-(13), the signal is present as FBAS(CCVS). The second input of the signal source switch Pin 15 isconnected to the Scart socket pin 20.At IC150-(16), the processor IC850-(42), voltage UVQ, transistor CT840decides as to whether the signal from the tuner or the external signalis processed.
3.4 External CCVS SignalAt the signal source switch IC150-(15) either an external CCVS signalfrom the Scart socket or the RF-CCVS signal is present. The voltageUVQ at IC150-(16) decides which signal shall be passed on, the CCVSsignal from the Scart socket or else the RF-CCVS signal. IC150-(16)"Low", the internal signal is selected; IC150-(16) "High", the externalsignal is passed on.Attention: If the option "Decoder On" has been selected the TVexpects the signal to come from the Scart socket. However the CCVSsignal from the tuner can be measured at output Pin 19 of the Scartsocket.
Bild ZF und DemodulationVision IF and Demodulation
FBAS und TonAusgangCCVS and SoundOutput
F130
ZF vom TunerIF from Tuner
Ufür denTunerfor the Tuner
URV vom Prozessorfrom Processor
AFC
KoinzidenzCoincidence
SyncDetector
TDA8362A~
45
46
2 3
47
49
9
4
7
~
GRUNDIG Service2 - 10
CUC 7303Schaltungsbeschreibung / Circuit Description
3.5 Sound IFAfter the ceramic filter F926, the sound signal is superimposed atIC150-(5) on a direct voltage for setting the volume level. Demodula-tion is effected by a PLL demodulator.In one path, the demodulated and uncontrolled AF signal is fed out atIC150-(1), it is then amplified by the transistors CT917, CT916 andpassed on to the Scart socket.In another path, the demodulated and controlled AF signal is presentat IC150-(50) and is fed to the AF-IC TDA7233.
3.6 Luminance and Chrominance SignalCalibration and control is effected automatically during the frameblanking period. The signals are adjusted by a positive or negativecurrent entering the integration capacitor CC177 at IC150-(12). Duringthe scanning period the control voltage is clamped.The luminance signal passes though the colour trap integrated in theIC. The delay line provided in the IC is used to correct delay timedifferences between the luminance and chrominance signal. Thecolour transient improvement (peaking) which follows is also realizedin this IC. For this, the steepness of the leading and trailing edges ofthe Y-signal is improved. The internal chroma filter separates thechrominance signal from the CCVS signal. A control circuit adjusts theamplitude of the colour signal for the chroma limiter and chromacontrol. The resulting chroma signal is passed on to the colourdemodulator. From this chroma signal, the burst is separated which isused to synchronise the colour oscillator in phase and frequency. Thequartz establishes a fixed 4.43MHz frequency for the colour carrier atPin 35. The quartz is controlled by an internal PLL circuit. Thecorrection voltage is integrated via the time constant at Pin 33. Bymeans of the colour carrier, the colour component signals are then
demodulated and leave IC150 as R-Y and B-Y signals at Pin 30 andPin 31 respectively. Following the PAL delay at CIC105 TDA4665 thetwo signals, B-Y and R-Y, are fed back to IC150-(28), -(29) TDA8362Awhere they are clamped.Subsequently, the colour contrast is controlled at IC150-(26). In thematrix, the RGB signals are produced from the amplified signals andthe Y-component.
3.7 SECAM Signal Path and Automatic PAL-SECAM SwitchingThe chroma signal of approx. 300mV for the SECAM-IC110 is presentat IC150-(27).On SECAM mode, a voltage between 5.6V…5.8V is applied toIC110-(16). When the IC110 identifies the SECAM standard from thechroma signal at pin 16, a current source at pin 1 is activated and sendsa SECAM identification to IC150-(32). As soon as IC150 too hasidentified SECAM, this IC sets pin 32 to 5V (1.5V on PAL). This directvoltage is superimposed either by a regular clock frequency on PAL,or by bursts at a frequency of 4.43 MHz on SECAM.The IC110 interprets these as an acknowledgement and switches thedifference signal outputs R-Y and B-Y (pins 9 and 10) to 3.5V DC (1.5Von PAL ). The difference signal outputs of IC150-(30), -(31) are thusblocked. IC110 now supplies the R-Y and B-Y signals. The differencesignals are returned to IC150 via the delay line CIC105. The followingpath of these signals is described unter 3.6 "Luminance andChrominance Signal".On SECAM reception the DC Level is switched to 3.5V at IC110-(10).Via CT115, UPAL changes to "Low" (PAL="High") and µP IC850-(1) isable to identify PAL or SECAM on ATS search (only FR variants).On OIRT reception (6.5MHz sound carrier), the search mode of the µP(UPAL) is switched over by CT915 via UAUDIO and CT115.
Ton ZF und DemodulationSound IF and Demodulation
Ton ZF +Lautstärkeregelung
Sound IF +Volume Control
HPFPLL
Demodulator
LPF
Ungeregelter Ton ScartUncontrolled Sound to Scart
Deemphasis
Geregelter TonControlled SoundTon von Scart
Sound from Scart
Schaltsignal vomProzessor
Switching Signalfrom Processor
5
6
16
50
1
LPF
Filterung des Luminanz- und ChrominanzsignalsLuminance and Chrominance Filter
Schaltsignal vom ProzessorSwitching Signal from Processor
FBAS von HFCCVS form RF
FBAS von ExternExternal CCVS
Regelspannung für die CalibrierungControl Voltage
for Calibration
CH
Y
16
13
15
12
Farb-TrapColour Trap
Delay Peaking2dB
Autom.Calibrierung
Auto Calibration
Farb-FilterChroma Filter
Farb-LimiterFarb-Regler
Chroma LimiterChroma Control
CUC 7303
GRUNDIG Service 2 - 11
Schaltungsbeschreibung / Circuit Description
3.8 RGB Signal PathFor contrast control of the RGB signals, IC850-(23) generates avariable control voltage for the contrast controlling amplifier atIC150-(25). Because too high a beam current may cause damage tothe picture tube, the beam current is limited by this IC. The internal peakbeam current limiting function is carried out in the peak white limitingstage. If the RGB signal exceeds 2.6Vpp, the internal peak white limitingfunction starts working and reduces the contrast. The external peakbeam current limiting threshold is 2Vpp approximately.The average beam current limiting function reduces the setting voltagesat IC150-(25) for the contrast.After the brightness amplifier, the RGB signals leave the IC150 and arepassed on to the cathode amplifiers on the CRT base panel.
3.9 Generation of the Horizontal and Vertical Sync SignalsThe TV signal processor IC150-(13,15) is connected to the CCVSsignal from the IF and from the EURO-AV socket. Following an internalcolour trap where the colour information is filtered off the CCVS signal,the resulting Y-signal now divides into two paths. In one path the signalis passed on for further processing, and in the other, the signal isapplied to the sync separator.The sync separator produces the horizontal and the vertical synchro-nising pulses from the Y-signal. The horizontal synchronising signal ispassed on to the ϕ1 phase control, the vertical synchronising pulse isused to start the line counter for vertical synchronisation.
3.10 Line OscillatorWith this IC concept, the line frequency is generated completely insidethe line oscillator. The IC is not connected to external components sothat it is not necessary to adjust the free running horizontal and the freerunning vertical frequency.
3.11 ϕ1 Phase ControlThe ϕ1 phase control stage is for controlling the frequency. This stageadjusts the frequency of the line oscillator to that of the line synchro-nising pulse. For this, the frequency of the line synchronising pulse iscompared with the line oscillator frequency.A ϕ1 phase control stage defines the time constant of the controlvoltage which is fed out at IC150-(40). The control voltage shifts the lineoscillator until the frequencies are equal.
3.12 ϕ2 Phase ControlThe ϕ2 phase control stage is for controlling the phase position of theline drive pulse. This determines the phase off-set between the linesynchronising pulses and the actual position of the electron beam.Dependent on the circuit components and the beam current, the delaytime between the external signal, the trigger signal and the actualreaction of the line output stage is different. These differences arecompensated for by the ϕ2 control.To identify the position of the electron beam the line flyback pulse fromthe line output transformer is applied to IC150-(38). From the oscillatorsignal and the line flyback pulse the ϕ2 controlling stage produces acontrol voltage at IC150-(39) which is filtered by CC166.
RGB AusgangsverstärkerRGB Output Amplifier
RGB internInternal RGB
RGB von Scartoder Videotext
RGB from Scartor Videotext
Data KontrastContrast
HelligkeitBrightness
RGB externExternal RGB
RGB zur BildrohrplatteRGB to the CRT panel
SpitzenweißBegrenzungPeak White
Limiting
222324
21 25 17
201918
Chroma-Signal
35
Farbkontrast vomProzessor
Colour Contrastfrom Processor
LuminanzsignalLuminance Signal
BurstPLL
(R-Y)
(B-Y)
(R-Y)
(B-Y)
Delay
Delay
RGBMatrix
R
G
BY
+
+
33
26
30
31
4,43MHz4,43MHz
34
3,58MHz
Farb-OszillatorColour Oscillator
29
28
H/2PAL-SchalterPAL Switch
TDA4662TDA4665 (OIRT/FR)
FarbdemodulationColour Demodulation
GRUNDIG Service2 - 12
CUC 7303Schaltungsbeschreibung / Circuit Description
3.13 The Super Sand Castle - SSCThe 3-level SSC signal IC150-(38) is a composite pulse consisting ofthe line flyback, the field flyback, and the burst key pulses. The lineflyback pulse (H-Sync) is fed through T523, CR163 to IC150. The fieldflyback and burst key pulses are generated inside the IC.If the field deflection stage fails, IC400-(7) pulls the SSC level to "Low"via R401 and thus blanks the CRT at IC150-(18, 19, 20) RGB. In doingso, the analog values are set to "Low".
3.14 Setting of the Cut Off VoltageAn automatic cut-off controlling stage ensures that the static workingpoints of the CRT are held stable. For this, IC150 feeds out a pulse tothe R, G, B cathodes during the lines 23, 24 and 25 to measure thebeam current of each system (approx. 10µA). The cut-off currentduring the measuring lines is fed via the resistor CR156 to IC150-(14).The IC compares this voltage with an internal reference value todetermine the working point for the black level of the video outputstages and the cut-off voltage of the CRT respectively.
3.15 The HDR Output StageFollowing an amplification stage the horizontal drive signal for the lineoutput transistor is provided at Pin 37.
3.16 The Field Deflection StageIn this circuit concept, the field sync generator is substituted by a linecounter.When no synchronising signals are received the line oscillator is freerunning. From this line oscillator the "vertical oscillator" is derived bycounting the number of lines. After having counted 312 lines, thecounter feeds out a field sync signal so that the horizontal and also thevertical deflection is achieved without using an external synchronisingsignal.
On reception of a synchronising signal, the line oscillator will first besynchronised. In this case too, the line counter supplies a field deflec-tion signal. As soon as a field synchronising signal is obtained the saw-tooth generator will no longer be triggered by the line counter butdirectly by the field sync signal.The saw-tooth generator is made up of a constant current source whichis used to charge and discharge an external capacitor. The chargingperiod is determined by the field sync signal. The field deflection signalcan be measured at the capacitor C158, IC150-(43).Adjustment of the field amplitude at the field output stage IC400 ispossible by influencing the field saw-tooth voltage. This alteration mustbe carried out before the field output stage. For this, a feedback signalfrom IC400 is present at IC150-(42) for negative feedback. Similar to anoperational amplifier connected to the negative input, this techniqueallows to set the desired parameters.
3.17 Non-Interlace Compensation with Teletext (25Hz Modulation)When a teletext (videotext) signal is displayed on the screen, theteletext signal would continuously change by one line upwards anddownwards (non-interlaced teletext signal). To avoid the signal chang-ing the line, the teletext IC850-(52) supplies a 25Hz switching signal toIC150-(43). From this U25Hz switching voltage, a small DC voltage offsetis derived for the deflection saw-tooth. This offset effects an upwardshift of the first half-field so that the even-numbered and odd-numberedlines are superimposed on each other.
3.18 CoincidenceThe coincidence information is generated in the IF stage and fed out onIC150-(4).
ZeilenoszillatorLine Oscillator
25 Hz
FBAS
CCVS
AmplitudensiebSync Separator
ϕ 1
ZeilenzählerLine Counter
V-Sync
H-Sync
ϕ 2 HDR
+
-VDR
SB VFB
40 36
Enable OszillatorEnable Oscillator
38 39Regelzeitkonstante für die ϕ 1-Regelung
Regelzeit-konstante für die ϕ 2-Regelung
Control Time Constantfor ϕ 2-Control
Flyback
37
43 42
44
Control Time Constantfor ϕ 1-Control
H/V-Synchronisation und AblenkungH/V Synchronisation and Deflection
CUC 7303 Abgleich / Alignment
GRUNDIG Service 3 - 1
D
AbgleichAlle nicht beschriebenen Einstellelemente sind werkseitig abgeglichen und dürfen im Servicefall nicht verstellt werden.
Meßgeräte: Zweikanal-Oszilloskop mit Tastkopf 10:1, Farbbildgenerator, hochohmiges Voltmeter.
Kontrolle und Einstellarbeiten nach Austausch bzw. Reparatur von:
Netzteil: 1.Zeilenablenkung: 2., 3.Bildröhre oder Bildrohrplatte: 2., 6.IC150: 4., 5.Tuner: 4, 5.
Abgleich
1. +A Spannung
2. Schirmgitter-spannung UG2
3. Zeilenschärfe
4. Bild-Demodulator(Bildträger 38,9MHz)
Bild-DemodulatorFrankreich-Norm
(Bildträger 33,4MHz)
5. Tuner-AGC
6. Weißwert
Abgleichvorgang
Mit Regler R654 eine Spannung von 112V (14" Orion),105V (14" Philips), 124V (15…21") einstellen.
Mit Regler UG2 (Splittrafo) an dem Meßpunkt mit dem höch-sten Schwarzwert eine Spannung von 100V…105V für 14"und 150V…155V für 15…21" Bildröhren abgleichen.
Schwarzwert
105-110V
Mit dem Fokusregler UF (Splittrafo) die horizontalen Linienauf maximale Schärfe stellen.
Mit dem Filter F130 die Gleichspannung auf 2,5V einstel-len.
Mit dem Trimmer C136 die Gleichspannung auf 2,5Veinstellen.
Wechselseitig wiederholen!
Mit den Tasten "V - oder + C" so abstimmen, daß dasBild gerade zu rauschen beginnt. Dann wieder zurückstel-len, bis das Bild gerade rauschfrei wird.
Einstellung mit "6" beenden.
Regler VG und VB auf der Bildrohrplatte so einstellen, daßkeine Verfärbungen in den Grauwerten sichtbar sind.
Vorbereitung
Helligkeit: MinimumVoltmeter: Kathode D682
Graubalken-Testbild einspeisen.Bildschirmhelligkeit so einstellen, daß die Abstufung vomdunkelsten Graubalken zu schwarz gerade noch sichtbarist, ca. 2,7V an IC150-(17).Mittlerer Kontrast (W).An den Meßpunkten R, G, B (auf der Bildrohrplatte)Oszilloskop anschließen und den höchsten Schwarz-wertpegel ermitteln.
Konvergenztestbild einspeisen.Kontrast (W) Maximum.Helligkeit so einstellen, daß sich der schwarze Testbild-hintergrund gerade aufhellt.
Generator mit Bildträger 38,9MHz, ca. 120mV an Tuner-Kontakt 10, 11 einspeisen.Norm 1 über Menü ("6" –> "OK") einstellen.Voltmeter: IC850-(34).
Generator mit Bildträger 33,4MHz, ca. 120mV an Tuner-Kontakt 10, 11 einspeisen.Norm 3 über Menü ("6" –> "OK") einstellen.Voltmeter: IC850-(34).
Normtestbild auf hohen UHF-Kanal legen und auf Pro-grammplatz 1 abspeichern.HF = 1,5mV (64dBµV, rauschfreies Bild).Gerät mit Netzschalter ausschalten.Servicemenü mit Fernbedienung aufrufen(Gerät einschalten, dabei Taste "6" gedrückt halten).Mit den Tasten "P+/P-" die Zeile "AGC ALIGN" anwählen.
FuBK-Testbild einspeisen.Farbkontrast (E) Minimum.Kontrast (W) Maximum.Bildschirmhelligkeit (R) so einstellen, daß die Abstufung vomdunkelsten Graubalken zu Schwarz gerade noch sichtbar ist.
100V…105V 14"150V…155V 15…21"
Abgleich / Alignment CUC 7303
3 - 2 GRUNDIG Service
Alignment Process
With control R654 set the voltage to112V (14" Orion), 105V (14" Philips), 124V (15…21").
With the control UG2 adjust the black level at the test pointwith the highest black level to approx. 100V…105V for 14"picture tubes and 150V…155V for 15…21" picture tubes.
Schwarzwert
105-110V
With the focus control UF on the focusing panel adjust thehorizontal lines for maximum sharpness.
With filter F130 set the DC level to 2.5V.
With trimmer C136 set the DC level to 2.5V.
Repeat mutual adjustments!
With the "V - or + C" buttons tune the station so thatnoise just starts to appear in the picture. Then reduce thevalue so that the noise just disappears from the picture.Terminate with "6".
Set the controls VG and VB on the CRT panel so that nodiscolouration is visible in the grey scale.
GB
Alignment
All adjustment controls not mentioned in this description are adjusted during production and must not be re-adjusted in the case of repairs.
Measuring Instruments: Oscilloscope with 10:1 test probe, colour test pattern, high resistance voltmeter
Checks and adjustments after replacement or repair of:
Power Supply: 1.Horizontal Deflection: 2., 3.Picture Tube, CRT-Panel: 2., 6.IC150: 4., 5.Tuner: 4., 5.
Alignment
1. +A Voltage
2. Screen gridvoltage UG2
3. Line sharpness
4. Visiondemodulator
(vision carrier 38.9 MHz)
Vision demodulatorFrench standard
(vision carrier 33.4MHz)
5. Tuner AGC
6. White balance
Preparations
Set luminance to mimimum.Connect the voltmeter to the cathode of D682.
Feed in a grey scale test pattern.Adjust the screen brightness so that the gradation from thedarkest grey scale value to black is just still visible(2.7V to IC150-(17).Set the contrast (W) to mid-value.Measure test points R, G, B (on the CRT panel) todetermine the test point with the highest black level andconnect this point to the oscilloscope.
Select the convergence test pattern.Contrast (W) to maximum.Set the brightness so that the black background of the testpattern is just brightening.
Feed in a generator with vision carrier 38.9MHz ca. 120mVon tuner contact 10, 11.Vision carrier 38.9 MHz.Norm 1 via Menü ("6" –> "OK")Voltmeter: IC850-(34)
Feed in a generator with vision carrier 33.4MHz ca. 120mVon tuner contact 10, 11.Norm 3 via Menü ("6" –> "OK")Voltmeter: IC850-(34)
Feed in a standard test pattern at a channel in the upperrange of the UHF band and store it at programme position 1.RF = 1.5mV (64dBµV, noise-free picture).Switch the TV off with the power button.Call up the Service Menu with remote control.(press and hold the button "6" and switching the TV on).With "P+/P-" buttons select the menu item "AGC ALIGN".
Feed in a FuBK test pattern.Set the colour contrast (E) to minimum.Set the contrast (W) to maximum.Adjust the screen brightness (R) so that the gradationfrom the darkest grey scale value to black is just stillvisible.
100V…105V 14"150V…155V 15…21"
Black level
CUC 7303 Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
GRUNDIG Service 4 - 1
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
AN10 348 255AN11 5 255AN12 5 5AN13 5 90AN14 162 147
AN15 348 90AN16 348 5AN30 9 10AN31 239 10
BR-HZ 121 171
BR01 245 133BR03 136 24BR07 241 69BR08 246 100BR09 234 59
BR10 244 105BR12 235 54BR13 250 137BR14 23 119BR16 150 135
BR17 146 133BR18 45 91BR24 31 131BR25 19 61BR26 146 106
BR27 241 124BR31 19 59BR33 123 96BR34 29 79BR36 91 38
BR38 122 94BR39 151 74BR40 30 101BR41 31 104BR42 31 99
BR43 35 76BR44 33 94BR45 192 115BR47 201 110BR48 227 84
BR49 42 89BR50 204 119BR51 173 67BR52 170 69BR53 167 69
BR54 24 117BR55 176 58BR56 159 95BR57 163 26BR58 43 86
BR59 179 105BR61 163 65BR62 126 70BR63 174 19BR64 177 19
BR67 100 31BR68 114 16BR69 89 20BR70 119 16BR73 208 99
BR74 235 96BR75 199 125BR76 189 109BR77 164 124BR79 189 21
BR80 238 38BR81 168 22
BR82 166 21BR84 181 22BR85 171 14
BR86 184 18BR88 43 51BR89 188 49BR99 160 18BR100 152 39
BR105 130 38BR106 127 146BR109 98 31BR111 81 25BR113 56 116
BR114 124 71BR115 125 19BR116 132 40BR117 65 29BR119 30 96
BR120 33 81BR121 68 34BR122 25 33BR123 40 73BR124 20 8
BR125 28 16BR128 32 59BR129 17 54BR130 142 235BR132 61 54
BR135 35 63BR136 35 66BR139 59 116BR141 9 51BR145 133 133
BR148 43 71BR150 114 129BR151 96 75BR152 108 70BR153 93 70
BR154 92 68BR155 131 116BR156 131 114BR157 129 111BR159 43 139
BR160 51 115BR161 54 116BR162 62 115BR164 25 136BR166 26 147
BR167 26 159BR168 59 140BR169 76 138BR170 82 154BR171 81 136
BR172 102 128BR173 123 154BR174 126 156BR175 81 60BR176 114 201
BR177 94 214BR178 89 221BR179 76 223BR181 69 237BR182 197 199
BR183 121 131BR184 167 202BR185 129 159BR186 159 201BR187 72 178
BR188 154 208BR189 72 174BR190 94 164BR197 108 190BR198 158 11
BR199 191 82BR200 215 41BR201 163 11BR203 256 29BR204 220 54
BR205 146 10BR526 18 200BR531 51 190BR532 95 191BR533 72 194
BR546 82 223BR600 220 224BR601 221 219BR671 94 230
C106 160 34C108 146 46C112 135 46C127 50 54C128 58 62
C129 47 61C136 61 84C141 89 85C145 67 63C148 53 60
C149 80 86C151 148 73C152 140 73C153 145 80C158 92 54
C167 99 46C191 141 89C302 33 54C303 18 30C309 41 56
C323 50 18C325 96 16C326 44 16C327 71 18C331 45 26
C402 65 163C408 16 145C412 82 162C417 85 191C422 59 168
C444 96 175C446 108 174C501 29 139C502 43 169C503 48 159
C506 28 180C511 64 131C512 201 137C513 63 125C522 38 196
C526 28 189C527 10 207C532 68 252C541 73 214C542 68 214
C543 116 193C601 221 203C603 229 164C604 238 165
C609 211 174
C621 191 199C622 195 175C623 191 192C624 191 176C626 150 179
C626 150 179C627 130 203C652 166 180C653 169 180C656 174 174
C661 181 205C663 176 225C664 150 198C667 173 203C669 154 234
C671 104 221C672 107 210C676 173 139C681 101 242C682 87 244
C682 87 244C683 28 108C687 38 129C695 155 139C811 258 172
C818 196 86C819 196 96C827 203 55C851 180 40C863 140 139
C911 48 79C921 116 26C922 110 26C923 105 45C924 95 39
C966 176 85C2810 168 89C2815 175 97C2816 183 97C2817 185 100
C2856 197 26C2858 11 31
CH01 267 58CO626 150 178
D323 104 13D401 69 157D405 73 137D406 64 154D444 100 175
D512 127 136D513 117 184D514 191 137D524 55 195D543 91 219
D621 190 168D622 191 162D623 190 187D624 188 178D661 151 210
D662 162 203D663 164 216D664 180 233D666 180 237D667 147 208
D668 156 209
D671 101 226D682 104 237D683 25 114D816 274 194
D816 272 194D826 243 28
ENTMAG 213 164
F130 71 84F901 67 53F906 80 51F923 89 109F924 89 94
F926 69 96F927 73 96F931 80 40
IC110 144 55IC150 95 70IC320 59 20IC400 60 151IC630 167 190
IC676 108 153IC690 141 153IC810 282 173IC810 277 173IC820 197 55
IC830 172 40IC850 204 71IC950 110 36IC2807 166 99
IR-BA 265 184KB 265 169KH335 269 36
L108 158 53L301 29 30L302 38 30L303 32 30L305 56 54
L381 260 36L506 20 195L526 18 200L531 50 180L533 72 194
L543 86 223L601 233 189L601 231 187L601- 231 187L819 196 114
L924 90 100L2836 204 89
NETZ 211 241NETZ02 213 221P+ 264 106P- 264 121P01 34 18
Q171 106 56Q172 99 56Q857 209 55
R118 125 53R119 121 53R156 42 68R166 16 22R183 100 101
R303 56 26R337 81 19R401 79 135
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
R406 73 169R408 9 156
R411 9 166R412 69 171R413 9 146R414 16 137R416 86 179
R502 45 164R503 28 155R504 35 166R506 9 176R511 70 136
R512 69 125R513 195 139R521 14 158R522 13 179R524 55 199
R526 20 203R531 51 190R532 95 191R533 73 206R542 117 133
R543 79 224R546 82 223R553 116 167R554 96 214R609 209 187
R621 197 199R627 166 165R633 186 217R651 175 191R652 180 181
R653 177 184R654 181 196R661 186 224R663 165 203R664 144 206
R665 171 225R666 161 241R667 164 241R669 155 209R681 91 172
R683 28 124R685 50 128
RGB 107 101S601 241 219SCART01 6 93SI600 231 239SI671 94 231
ST-BAT01 232 63ST-BAT04 81 213ST-BAT03 105 143ST-BAT02 71 244ST-J 69 182
T501 39 160T506 9 189T511 75 124T523 142 125T601- 127 226
T665 172 229T68640 122TR501 25 168TR550 37 227TR601 129 232
TRX550 37 227TUNER 30 42
Bestückungskoordinaten der Bauteile- Die Koordinaten X und Y sind sowohl als metrische Koordina-
ten für die Originalplatine in Millimeter, als auch als absoluteKoordinaten für die vergrößerten Abbildungen der Platinenverwendbar.
C --> Kondensator CC --> Chip-KondensatorD --> Diode CD --> Chip-DiodeIC --> Integrierter Schaltkreis CIC--> Chip-ICL --> Spule CL --> Chip-SpuleR --> Widerstand CR --> Chip-WiderstandT --> Transistor CT --> Chip-Transistor
Assembly coordinates of the components- The X and Y coordinates can be used as both metric coordi-
nates in mm for the original circuit board and absolutecoordinates for the enlarged diagrams of the circuit boards.
C --> Capacitor CC --> Chip CapacitorD --> Diode CD --> Chip DiodeIC --> Integrated Circuit CIC--> Chip ICL --> Coil CL --> Chip CoilR --> Resistor CR --> Chip ResistorT --> Transistor CT --> Chip Transistor
Chassis BoardCoordinates of the components on the components side (top side)
ChassisplatteKoordinaten für die Bauteile der Bestückungsseite (Oberseite)
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams CUC 7303
4 - 2 GRUNDIG Service
Coordinates of the Components on the Solder Side(Bottom Side)
Koordinaten für die Bauteile der Lötseite(Unterseite)
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
CBR01 78 74CBR02 254 170CBR03 155 26CBR04 118 83CBR05 224 68
CBR06 148 64CBR07 40 38CBR08 20 47CBR09 45 30CBR11 87 48
CBR12 175 32CBR13 156 80CBR15 211 38CBR16 211 42CBR17 77 95
CBR19 130 101CBR21 210 18CBR22 232 42CBR23 176 73CBR24 128 125
CBR25 226 43CBR26 226 40CBR27 42 72CBR28 183 20CBR29 212 26
CBR30 47 99CBR31 193 40CBR32 181 86CBR37 137 78CBR41 30 38
CBR42 131 55CBR43 190 40CBR44 186 40CBR46 92 129CBR47 90 48
CBR52 25 14CBR53 68 34CBR54 22 38CBR55 25 38CBR57 22 25
CBR58 18 35CBR59 92 71CBR61 92 97CBR62 83 86CBR66 152 26
CBR68 128 15CBR71 48 88CBR72 48 81CBR73 88 125CBR84 238 119
CBR85 96 136CBR86 181 20CBR90 137 68CBR98 48 76CBR101 72 55
CBR108 42 69CBR109 128 21CBR113 121 78CBR115 78 86CBR119 166 72
CBR120 125 45CBR124 60 97CBR125 48 91CBR126 182 106CBR127 117 99
CBR133 94 136CBR134 96 91CBR135 210 70CBR137 259 158CBR175 130 58
CBR881 223 84
CC106 158 46CC107 157 40CC108 155 47CC109 142 55CC111 137 48
CC113 111 59CC114 108 59CC115 164 64CC118 112 47CC119 121 53
CC124 82 76CC126 114 59CC127 117 59CC130 124 29CC134 75 75
CC135 66 80CC136 61 84
CC139 71 88CC140 80 60CC141 89 86
CC142 95 75CC143 86 82CC144 67 63CC146 97 84CC147 53 95
CC149 72 75CC156 86 67CC157 91 67CC163 88 129CC166 97 66
CC167 94 66CC171 103 52CC172 101 52CC173 107 71CC174 108 66
CC177 92 75CC184 102 89CC307 29 46CC308 26 46CC321 62 21
CC322 54 19CC328 68 16CC331 45 22CC381 260 27CC382 247 22
CC383 257 31CC401 68 146CC403 68 165CC406 58 156CC419 53 154
CC501 29 155CC653 172 191CC654 172 181CC673 112 150CC674 107 139
CC676 108 162CC682 28 111CC694 138 148CC695 142 148CC805 254 165
CC807 200 94CC808 228 56CC818 183 74CC820 213 67CC821 204 43
CC822 227 73CC823 230 91CC825 159 110CC826 205 55CC827 198 68
CC831 168 39CC836 195 68CC837 186 89CC838 197 75CC842 187 48
CC848 186 52CC852 172 64CC854 211 48CC855 183 58CC856 208 68
CC859 190 96CC863 190 71CC865 229 73CC866 197 72CC868 200 38
CC869 200 33CC881 232 73CC901 78 54CC902 78 46CC906 84 60
CC920 84 104CC921 129 107CC922 126 107CC923 124 107CC924 75 103
CC925 88 97CC926 108 36CC930 100 110CC937 65 98CC944 68 38
CC951 5 108CC956 121 29CC957 9 108CC958 9 104CC973 18 104
CC2801 181 58CC2802 175 63CC2803 180 71CC2811 169 99CC2820 212 100
CC2821 224 91CC2822 219 91CC2823 215 91CC2825 215 38CC2835 203 20
CC2836 202 75CC2837 205 75CC2841 210 22CC2845 213 20CC2850 200 48
CC2851 196 43
CD109 146 56CD134 61 81CD135 67 76CD181 103 100CD191 134 78
CD192 134 95CD193 130 78CD194 132 83CD501 32 157CD516 186 133
CD651 169 190CD654 176 176CD656 177 184CD673 100 162CD830 244 128
CD901 72 49CD902 74 53CD926 69 103CD927 72 103CD941 78 36
CD942 76 36CD943 73 42CD944 73 36CD954 22 87CD2827 154 93
CD2829 150 93
CIC105 114 52CIC130 144 26
CR100 186 43CR101 160 36CR102 160 40CR103 162 37CR104 162 41
CR105 141 45CR106 141 41CR107 149 41CR108 152 56CR109 149 56
CR110 138 56CR111 157 94CR112 159 86CR113 156 88CR114 166 53
CR115 162 64CR116 144 64CR121 102 74CR122 115 72CR124 44 60
CR126 207 123CR127 48 54CR128 49 62CR130 134 24CR131 134 19
CR132 48 84CR133 140 19CR134 64 75CR135 138 19CR136 71 84
CR137 145 19CR138 142 19CR139 76 81CR141 89 73CR143 81 71
CR147 56 95CR148 49 95CR149 77 91CR151 108 82CR152 105 82
CR153 103 82CR154 127 53CR155 88 52
CR156 100 84CR158 89 67
CR159 101 65CR161 89 56CR162 53 105CR163 85 129CR164 20 21
CR165 93 47CR166 95 49CR167 96 55CR168 86 54CR169 49 104
CR171 102 60CR173 105 66CR174 120 64CR175 120 60CR181 98 102
CR182 96 102CR183 99 89CR186 105 89CR187 149 88CR191 136 83
CR192 134 87CR193 147 88CR194 130 90CR304 43 33CR305 35 38
CR306 26 72CR307 24 72CR309 41 60CR321 68 20CR322 53 16
CR323 91 19CR324 98 17CR325 60 13CR326 41 20CR327 100 17
CR328 45 20CR329 58 20CR331 41 22CR381 257 27CR382 263 27
CR403 60 165CR404 73 162CR405 74 127CR406 14 150CR407 17 138
CR408 17 134CR409 65 146CR419 6 149CR523 63 134CR541 106 121
CR654 172 184CR656 181 182CR673 100 155CR674 103 162CR686 43 118
CR687 38 125CR803 241 114CR807 199 89CR808 222 60CR811 260 181
CR812 259 136CR813 259 139CR816 260 186CR817 251 165CR818 185 82
CR819 258 184CR820 228 60CR821 221 100CR822 217 91CR823 227 91
CR824 222 91CR825 219 74CR826 209 95CR827 201 68CR828 205 68
CR829 203 68CR830 248 127CR832 184 48CR833 215 100CR834 214 83
CR835 193 67CR836 191 67CR837 193 35CR838 184 89CR839 188 86
CR840 175 58
CR841 180 106CR843 182 48CR844 189 52CR845 217 74
CR846 174 53CR847 182 43CR848 181 53CR849 171 53CR850 189 67
CR851 190 48CR852 178 53CR853 168 53CR854 167 64CR855 169 64
CR856 186 58CR857 211 54CR858 188 120CR859 186 67CR860 213 74
CR861 228 67CR862 191 75CR863 189 75CR864 230 60CR865 231 67
CR866 236 73CR867 232 60CR868 172 30CR869 172 32CR870 202 33
CR873 202 38CR875 215 74CR876 193 74CR877 201 43CR878 188 96
CR879 210 74CR880 192 82CR881 232 78CR882 236 78CR901 70 45
CR902 81 47CR903 128 25CR904 66 53CR905 147 19CR906 149 19
CR907 52 46CR911 92 91CR916 52 82CR917 55 73CR918 55 82
CR919 70 76CR920 83 108CR921 77 100CR922 84 102CR923 78 110
CR924 87 103CR925 75 108CR926 70 109CR927 73 108CR928 65 100
CR929 65 103CR930 80 110CR931 67 109CR936 59 106CR937 62 106
CR938 65 108CR941 77 42CR944 84 31CR951 5 112CR952 5 103
CR953 37 110CR954 20 83CR957 17 112CR958 17 99CR959 17 95
CR960 17 109CR961 16 88CR962 18 79CR963 98 118CR964 17 64
CR965 98 121CR966 98 123CR967 16 68CR968 12 65CR971 12 70
CR974 99 74CR984 56 89CR985 132 16CR2801 178 58CR2802 178 63
CR2803 180 75CR2810 215 44CR2811 226 49CR2812 228 49CR2813 169 107
CR2814 178 101CR2815 221 46CR2820 215 28CR2821 147 93CR2822 221 41
CR2823 218 41CR2824 224 34CR2825 227 28CR2826 224 32CR2827 224 36
CR2829 152 88CR2830 150 105CR2831 200 17CR2832 198 17CR2833 147 106
CR2834 193 22CR2836 192 17CR2837 195 17CR2839 186 74CR2840 218 28
CR2841 227 23CR2842 227 25CR2843 215 23CR2846 218 23CR2847 222 23
CR2848 205 33CR2849 211 30CR2850 194 55CR2851 199 43CR2852 206 43
CR2853 205 28CR2856 208 28CR2858 20 11
CT101 161 46CT106 145 41CT107 153 42CT110 164 88CT115 163 59
CT169 53 101CT181 97 96CT186 102 93CT191 141 84CT193 140 93
CT325 77 15CT826 214 95CT840 158 105CT881 226 84CT901 79 51
CT916 55 76CT917 59 76CT919 60 88CT921 79 105CT925 82 98
CT937 60 102CT962 17 74CT963 21 67CT2820 219 34CT2821 143 106
CT2825 229 32CT2830 198 22CT2831 153 105CT2835 189 23CT2840 206 20
CT2845 222 27CT2850 209 33
OM01 240 20OM02 15 255OM03 265 204OM04 53 257OM05 8 18
Pos.-Nr./ Koordinaten/Pos. No. Coordinates
X Y
GRUNDIG Service
CUC 7303 Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
GRUNDIG Service
CUC 7303 Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
ChassisplatteChassis Board
Bestückungsseite, Ansicht von obenComponent side, top view
4 - 3 4 - 4
8
29304-764.54/2L(02) 0 1 2 3 4 5 6 7 8 9
C106
C81
1
C12
7
C15
1
C15
2
C14
8
C92
1
C92
2
C12
9
C16
7
C149
C12
8
C85
1
C15
3
C911
C191
C108C
863
C32
5
C656
C663
C323C326
C66
1
C92
4
C92
3
C96
6
C309
C82
7
C28
15
C28
16
C818
L108
L924
L302
L303 L301
L283
6
F926
F927
D816 R524
D406
P+
P-
+P-P
F924
C11
2
C15
8Q17
1 Q17
2
Q85
7
13
IC81
0
13
1 8
916
IC110
F906
R65
4
F901
R406
R414
R18
3
R65
3
R66
7
R66
6R
663
R66
5
R661
R65
2
R51
1
R683
5227
26 1
IC150
F923
CH
1
D323
D66
3
C136
1
21
SC
AR
T1
D40
5
C543
C412
C67
6
C446
C672
L601
C511
C683
C69
5
C28
10
C303
C302
C0682
R66
4
R633
C51
2
C40
8
C50
1
C687
F931
D66
7
D66
8
R65
1
D67
1
D62
4
D621
D401
D524
D623
D622
D664
D666
D54
3
D513
D44
4
D66
2
D82
6
C621
C62
2
C67
1C
681
C502
C44
4
C623
C62
4
C65
2
C66
4
C422
C503
C513
CE
T523
C E
T511 C E
T686
C62
6
4
1
6
9
18
12
15
R533
L506
L381
C682
R526
R502
BR189
BR154
BR041
BR
052
BR
051
BR025
BR
053
BR089
1 3
6 5 4
TR50
1
R50
6
R52
1
R51
2
BE
T506
C522
C66
9
D66
1
D51
4
D683
C601
C506
C52
6
L531
SI6
71
R52
2
R62
7
C402
C327
C331
C
EB
T665
C54
1
C54
2
C2856
R41
3R
411
R40
8
R532
L526
C52
7
ENTMAG
BR136
1 4
5 8 IC630
3 1
IC690
112
13
TR550
C532
E BT501
D68
2
13
IC676
R40
1
L533
S601
R11
9
R41
6
R412
R685
R50
4
R11
8
R51
3
R337
BR
190
BR
024
BR170
BR031
BR
184
BR155
BR
026
BR
186
BR
016
BR018
BR
059
BR
039 BR043
BR
172
BR
073
BR010
BR
055
BR
069
BR048
BR
084
BR
045
BR
047
BR
050
BR074
BR
082
BR
079
BR
085
BR
178
BR175
BR
114
BR
062
BR054
C609
C65
3
C627
C60
3C60
4
F130
BR128
BR
198
BR156
BR
067
BR
057
BR080
BR027R
609
1 4
58
IC320
17 10
2
TR601
P1
ST-BAT2
BR
111
BR151
BR
179
BR049
BR123
BR
164
BR
100
BR038
BR040
BR042
BR044
BR
145
BR119
BR199
BR
086
BR
200
R531
R503
14
5 8
IC830
1 4
58IC2807
R55
3
R156
R54
6
17
8 14
IC950
L543
BR
121
BR
177
BR033
BR173
BR058
BR
068
BR148
BR135
BR
188
BR176
BR001
BR013
BR152
BR
109
BR187
BR
201
BR012
BR
203
BR
150
BR
130
BR
077
BR
162
BR
183
BR116
BR
115
BR129
BR166
BR
168
BR
169
BR
139
BR
113
BR204
12
3 4
BR
017
BR
003
BR
197
BR153
BR
160
BR034
BR
161
BR
171
BR
125
BR
070
BR157
C81
9
1K
B
BR
063
BR124
BR185
BR
036
BR
159
BR174
BR
117
BR
064
1
10
11
TRX550
BR007
R55
4
R54
3C
417
19
IC400
BR014
R68
1
BR531
BR088
BR181
BR167
BR141BR
132
BR106
C28
58
C667
C141
1IR
-BA
BR526
R16
6
111
TUNER
220V-2240~
NETZ
D51
2
SI600
R66
9
R62
1
43
2 1
BR
671
BR120
BR
061
15
15
BR
-HZ
17
RG
B
BR600
BR533
BR601
BR
182
BR
546
R54
2
BR
076
BR008
BR
075
R303
NE
TZ2
BR
081
1 2
ST-
BA
T4
1 2
ST-BAT1
1 3
ST-BAT3
31
IC82
0
1 26
2752IC850
BR
056
L819
BR105
BR009
BR
099
BR122
C145
BR205
KH335
C2817
29304-764.54/4B(02)
KEINE NETZTRENNUNG
M
M +
-
R41
4
BA
BABA
T2A
T2,5A L
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
260
Y
0102030405060708090100110120130140150160170180190200210220230240250260270280290 X
ML I
K
H
G
F
E
DCB
A
4
27
23
25
22
24
26
19
16
29
17
10
21
2830
12
13
20
14
15
11
9
18
8
6
7
1
5
3
2
30
GRUNDIG Service
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams CUC 7303
GRUNDIG Service
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams CUC 7303
ChassisplatteChassis Board
4 - 5 4 - 6
Lötseite, Ansicht von untenSolder side, bottom view
8
29304-764.54/2L(02)0 1 2 3 4 5 6 7 8 9
CD
501
CD
193
CD654
CD
109
CD
673
CD954
CD516
CD
2829
CB
R044
CD
2827
CD
656
CD
191
CD
181
CR
851
CR
541
116 9
8CIC130
116 9
8CIC105
CB
R066
CR
923
CR
2810
CC
2836
CC
822
CR155
CR
958C
R959
CR
954
CR
961
CR960
CR
924
CR171
CR911
CR
183
CR
128
CR
127
CR
919
CR
152
CR159
CR
153
CR
186
CR
938
CR
967
CR928
CR962
CR
109
CR
147
CR
105
CR984
CR951
CR952
CR
106
CR
103
CR
181
CR
165
CR902
CR162
CR957 CR
936
CR331
CR
164
CR929
CR328 CR
322
CR
905
CR
137
CR
131
CR
133
CR
135
CR
321
CR
193
CR
138
CR964
CR
182
CR
325
CR
404
CR
104
CR
173
CR167
CR
126
CR
903
CR
112
CR
2848
CR
906
CR
101
CR
187
CR2849
CR
861
CR
2830
CR
409
CR405
CR944
CR921
CR917
CR941
CR
324
CR326
CR
937
CR
108
CR
953
CR922
CR
151
CR149
CR
327
CR
833
CR
192
CR
113
CC
2825
CR
808
CR904
CR
191
CR2827
CR2824
CR2826
CR
2831
CR
2837C
R2834
CR
2836
CR
2832
CR2841
CR2847
CR
2843
CR
2846
CR2842
CR
2851
CR
848
CR
2856
CB
R052
CR136
CR
2852
CR819
CC808
CB
R881
CR
2853
CR
2829
CR139
CR
2821
CR
309
CR
329
CR
2801
CR
2802C
R2803
CR
818
CR812
CR813
CR
817
CR816
CR
840
CR
828
CR
169
CR
143
CR
114
CR654
CR
115
CR
843
CR
847
CR
845
CR
825
CR
877
CR
876
CR
875
CR868
CR
873
CR
862
CR
858
CR
824
CR100
CR
846
CR
849
CR
855
CR
854
CR
853
CR
827
CR
822
CR
863
CR
857
CR
856
CR
852
CR
844
CR
829
CR
866
CR
870
CR
307
CR
306
CR
2814
CR
110
CR
194
CR
161
CR
107
CR
823
CR
2820
CR2825
CR
2815
CR
830
CR
820
CR
834
CR
835
CR
836
CR
859
CR
867C
R865
CR
2840
CR
907
CR
850
CR
381
CR
382
CR
971
CR2850
CR
880
CR
860
CR
864
CR
832
CR
879
CT916
CT917
CR
841
CT901
CD
192
CD194
CR
674
CR963
CR
111
CR686
CC654
CR
102
CD134
CR
163
CC
807
CR
918
CR
156
CR
116
CR901
CR
931
CC930
CR
141
CB
R058
CR
408C
R407
CR
673
CR687
CR
166
CR
419
CR
916
CR
838
CR523
CR
130
CR
926
CR
974
CR
121
CR132
CR
985
CR
304
CR403
CR965
CB
R126
CR148
CR
968
CR
122
CB
R031
CR
2823
CR
2812
CR305
CR
826
CR869
CR
2833
CR
925
CR
927
CR811
CR
2839
CR2813
CB
R032
CR966
CR839
CB
R012
CR
2811
CR
2822
CC136
CC
156
CC
147
CC920
CC
184
CC973
CC331
CC321
CC
142
CC
172
CC925
CC
171
CC
166
CC
119
CC
111
CC
130
CC
958
CC
143
CC
924
CC
177C
C157
CC906
CC
174
CC
134
CC
167
CC
113
CC
126
CC951
CC
957
CC
108
CC322
CC
328
CC937
CC
114
CC140
CC124
CC
144
CB
R022
CC118
CC419
CC
501
CC
173
CC
141
CC901
CC
106
CC
956
CC
127
CC944
CC
831
CC
848
CC
674
CC
922
CC
923
CC
921
CC
2851
CC
307
CC
2802
CC
2803
CC
2837
CC
856
CC
308
CC
2845
CC
842
CC
852
CC
855
CC
859
CC863CC866
CC
820
CC
837
CC
821
CC
868
CC
115
CC838
CC
2821
CC
2822
CC
2823
CC
836
CC
805
CC
2841
CC
2811
CC
825
CC139
CC135
CC
869
CC
676
CC
381
CC
383
CC682
CBR057
CB
R109
CB
R053
CC
826
CB
R101
CBR059
CBR125
CB
R135
CB
R043
CBR004
CB
R021
CB
R085
CB
R008
CBR108
CBR098
CB
R009 C
BR
003
CBR072
CB
R133
CB
R068
CB
R037
CB
R115
CB
R062
CB
R090
CBR071
CB
R017
CB
R046
CB
R113
CBR041
CBR127
CC
2820
CC
827
CB
R002
CBR124
CB
R007
CB
R086
CC
2850
CB
R001
CB
R084
CB
R013
CC
902
CBR016
CBR019
CBR015
CB
R023
CB
R024
CBR025
CBR026
CBR027
CB
R028
CBR029
CBR030
CR
878
CD830
CR
821
CD
902
CD
944
CD
941
CD
926
CD
901
CD943
CD
927
CD
942
CC
149
CD
135
CC
653
CC
107
CC
109
CC403
CC406
CC
694CC
673
CR
406
CR
134
CC
163
CC
146
CC
695
CC
818
CC
926
CR
656
CC
854
CC
865
CC
401
CB
R054
CBR073
CB
R120
CBR061
CB
R119
CBR134
CBR042
CB
R006
CBR055
EB
CT963
E B
CT107
EB
CT325
EB
CT186
EB
CT937
EBCT2850
E B
CT2820
EBCT2830
CC
2801
E B
CT2840
E B
CT840
E B
CT115
EB
CT826
EB
CT101
EB
CT193
EB
CT925
E B
CT169
E B
CT110
EB
CT191
EB
CT962
EB
CT106
E B
CT181
E B
CT919
E B
CT2825
EBCT2835
E B
CT2845
EB
CT2821
CC
881
EBC
T881
CR881
CR168
CB
R005
CC
823
CB
R011
EB
CT2831EB
CT921
CR
837
CR
124
CR
154
CBR175
CB
R047
CR
920
CR
175C
R174
CR323
CD
651
CR2858
CB
R137
CR803
CR882
CR807
CC
382
29304-764.54/4LS(02)
0
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
160
170
180
190
200
210
220
230
240
250
260
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290
Y
X
GRUNDIG Service
CUC 7303 Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
GRUNDIG Service
CUC 7303 Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
Chassisplatte / Chassis Board
4 - 84- 7
0V
1 500mV/cm, 5µs/cm
0V
5V/cm, 500ms/cm2
0V
3 5V/cm, 5µs/cm
0V
4 100V/cm, 5µs/cmin Betriebin operation
0V
5 500mV/cm, 5µs/cm
6V
100mV/cm, 20µs/cm6
1,5V
100mV/cm, 20µs/cm7
1,5V
100mV/cm, 20µs/cm8
4V
500mV/cm, 20µs/cm9
4V
500mV/cm, 20µs/cm10
2V
200mV/cm, 1µs/cm11
0V
500mV/cm, 250ns/cm12
0V
2V/cm, 20µs/cm13
0V
1V/cm, 10ms/cm14
0V
1V/cm, 20µs/cm15
0V
1V/cm, 20µs/cm16
0V
1V/cm, 20µs/cm17
0V
1V/cm, 50µs/cm18
0V
1V/cm, 20µs/cm19
0V
1V/cm, 5ms/cm20
0V
1V/cm, 5ms/cm21
0V
5V/cm, 20µs/cm22
0V
200V/cm, 20µs/cm23
0V
10V/cm, 5ms/cm24
0V2V/cm, 5ms/cm25
0V
2V/cm, 20µs/cm26
0V
50V/cm, 20µs/cm27
0V
1V/cm, 10µs/cm28
0V500mV/cm, 10µs/cm29
0V
2V/cm, 200µs/cm30
0V
GRUNDIG Service
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams CUC 7303
GRUNDIG Service
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams CUC 7303
Gesamtschaltplan / General Circuit Diagram
4 - 9 4 - 10
22k
CR
881
100
CR
861
150k
CR
2849
330
CR2848
5,6k
CR2850
4,7k
CR
879
100
CR
864
100k
CR
880
0
CB
R88
1
UB
ATT
0
CR830
LS4148
CD830
**
CR2825
0
CR2820
10k
CR
860
BC858BCT2831
UE
NTM
A
UB
ATT
10k
CR
2830
*
2,2k
CR
8352,2k
CR
850
INL
US
CH
UTZ
2,2k
CR
836
KC671
270p/2kV
FC
2856
33n
5,6k
CR
834
4,7k
CR
820
1
2
ST-BAT1
0
CR865
1,8k
CR2829
680
CR
2821
47k
CR
2833
UD
ATA
PE
RI
UE
UR
O-
AV
BC858BCT2821
LS4148
CD2829
UE
NTM
A
270
CR
2814
*CR2813
LS41
48
CD
2827
FBA
SE
UR
O-A
V
UV
Q
+
2,2u
/100
V
C28
16
FBA
SS
C+
100u
/25V
C28
10
0,1u
CC
2811
6dB
0dB
0dB
1
2
3
4
5
6
7
8TEA2114
IC2807
+
1u/1
00V
C28
15
LINESTO
LINESTO
PLLCLOCK PROZ.
8
5
43
16
14
TDA4665T(O
TDA46
C621
1n
10p(FR)
CC109
10n
CC
682
47k
CR
813
10k
CR
826
47k
CR
812
100
CR
870
0
CR
866
4,7k
CR
829
1,8k
CR821
220
CR
844
100k
CR
848
47k
CR
852
*
CR
856
33
CR
857
150k
CR
863
3,9k
CR
824
3,9k
CR
823
10k
CR
827
3,9k
CR
822
390k
CR
853
110k
CR
854
68k
CR
855
330k
CR
849
220k
CR
846
SS
C
4,7k
CR
841
10k
CR
858
68k
CR
862
100
CR
833
100
CR
873
10k
CR
839
3,3k
CR
868
3,3k
CR
869
1k
CR
807
1k
CR
808
100
CR
875
47k
CR
876
100
CR
877
150k
CR
878
100
CR
825
5,6u
L641
100
CR
845
470k
CR101
8,2k
CR103
10k
CR104
47k
CR102
2,2k
CR
107
10k
CR
108
10k
CR106
1,2k
/1%
CR
687
390/
1%
CR
673
BR
641
GB
BR
182
430/1%
CR686
3,4k
/1%
CR
674
3
2
1
ST-BAT3
P
P
P P P P
P
P
P
P
PP
P
M
M
P
P
P
K
470p
C65
3
K
1n/4
00V
-AC
C60
4K
1n/4
00V
_AC
C60
3
US
TAN
DB
Y
2,2k
CR
859
1M
CR656
XX
CC
2841
+
1u/1
00V
C85
1
10k
CR
832
39k
CR
838
330k
CR
847
47k
CR
851
100
CR
641
INL
1
2
ST-BAT2
+5V
IR3
21
TFMS5300
IC810
TLH
R46
01
D81
6
SD
A
SC
L
SC
L
EN
A
P-
SD
A
P+
0,1u
CC
827
UE
UR
O-
AV
+
-
VREF5,0V
U<8,5V
GLOGIK
BWM
V
8
7 6
54
3
2 1
UC3842N/AN
IC6302 56
R66
4
US
TAN
DB
Y
UN
FM
UTE
18MHz
Q857
BC858BCT106
R62
1
4,7
43
21
S601
1
2
3MC7805T
IC690
LS41
48
CD
673
LS4148
CD654
LS4148
CD656
-(R-Y)
-(B-Y)
TUNING
PHASISDEEM
PLLBELLACC
SWITCHIDENT.CONTROLFACEINTER-
1112131415
16
5 6 7 8
3
4
1
2
TDA8395N2
IC110
VCCSDA
SCLA0 A1 A2 VSS
TEST
8
76
5
4321
X24C02
IC830
ZTK
33B
D68
3
3,6V
D66
3
n.v.
UD
ATA
UFB
AS
U DATA-P
UK
OIN
UN
OR
M1
UV
Q
BC848B
CT826
BC848BCT101
BC848BCT107
BC848BCT840
L819
-051
+
470u
/40V
C67
2
+
2,2u
/63V
C66
3
3
2
1
KB
+
47u/
16V
C81
1
+
47u/
16V
C10
8
+
4.7/
63V
C86
3
+
100u
/25V
C69
5
+
22u/
16V
C68
7
+
47/5
0V
C68
3
+
470u
/25V
C67
6
+
100u
/25V
C66
7
+
*/38
5V
C62
6
+
100u
/250
V
C68
2
+
1u/6
3V
C66
1
+
2,2u/100V
C656
BY297
D671
BY299
D682
BY
T53G
D66
8
1N40
03
D66
4
1N40
03
D66
6
BA
157
D66
2
BA157
D667
BY
T53B
D66
1
5,6k
CR
837
0,1u
C81
9
BR601
BR600
447
0
R66
9
P3
P3
4,7M
R62
7
FR/OIRT
3 2
1
LM317T
IC676
100p
C681
C623
1n
F
1n/F
KP
/160
0V
C66
9
F
2,2n/400V_AC
C627
F
0,22
u
C11
2
F
*/M
P3/
250V
/AC
C60
1
826-9729500-
L601
1N4007
D623
1N4007
D624
1N4007
D621
1N4007
D622
n.v.
100p
CC805
0,1u
CC831
10p
CC2823
10p
CC2822
10p
CC2821
0(OIRT)91k(FR)
CR109
56p
CC
854
15p
CC
856
10n
CC
838
100p
CC
869
100p
CC
868
2,2n
CC
821
100p
CC
822
1n
CC
823
100p
CC
837
1n
CC
836
100p
CC
866
2,2n
CC
863
100p
CC
859
100p
CC
855
100p
CC
852
100p
CC
848
100p
CC
842
100p
CC
825
100p
CC
865
0,1u
CC107
0,1u
CC
111
1n
CC
106
0,1u
CC
108
1n
CC
114
1n
CC
113
2,2n
CC
674
0,22
u
CC
694
0,1u
CC
695
0,22
u
CC
673
0,1u
CC
676
10n
CC
653
1,2n
CC
654
LS41
48(F
R)
CD
109
T2,5A L
SI600
*
R66
6
0,82
R66
7
220
R661
18
R66
3 1k
R66
5
4,7k
R651
330
CR
816
22k
CR817
270
CR811
100
CR
803
C622
1n
150k
CR
654
*
R653
10k
R652
UA
FC
UR
V
15
R685
2 56k
R63
3
BR
056
0
CR867
*R609
5
4
3
2
1
IR-BA
BO
SD
VS
YN
C
HS
YN
C
100u
H
L108
470R654
212k
R681
330k
CR
840
GB
MJF18004CT665
BC337/25T686
2
1N3
390k
CR
116
1
2
3
5
6
7 10
*TR601
200k
CR
115
4,7n
CC
115
BC848BCT115
10k
CR114UP
AL
UP
AL
3
2 1MC33164
IC820
C624
1n
220p
CC807
IR
Min.+A
37cm
OIR
T
BR
663
BR646
37cm
37cm
0,1uC
C81
8
82k
CR818
6,8u/2%
L2836
120p
/2%
CC
2837
33p/
1%
CC
2836
33n
CC280333n
CC28020,22u
CC2801
6,8k
CR2803
6,8k
CR2802
8,2k
CR2801
4,7k
CR
2812
4,7k
CR
2811
4,7k
CR
2810
1M
CR
2839
1,5n
CC2851
T2,5A
SI671
FC
2858
33n
PMBT2369CT2850
22k
CR
2853
10k
CR
2852
22k
CR2858
22k
CR2856
3,9k
CR2851
10k
CR2842
xx
CR2846
10k
CR
2843
xx
CR2847
10k
CR2841
BC858BCT2845
xxCT2840
10k
CR2832
xx
CR
2836
10k
CR
2834
xx
CR2837
10k
CR2831
BC858BCT2835
xxCT2830
10k
CR2822
xx
CR
2826
10k
CR
2824
xx
CR2827
10k
CR2823
BC858BCT2825
xxCT2820
GB
*
R68
3
1k
CR819
+
1u/1
00V
C82
7
+
2,2u/50V
C106
0
CR110
OIRT
FC65
2
4,7n
0
CR
2815
+
4,7u/63V
C818
100p
CC
2850
OIR
T
TEXT
10n
CC
881
**CT881
33k
CR882
U25
Hz
UA
UD
IO
BR671
n.V.
TEXT
n.v.
C664
4,7n
220p
CC808
ZD18
V/2
%
CD
651
CL35
VD
D
VS
S
VS
S1
P0.
3
P0.
4
P3.
4
P2.
1
P2.
2
P1.
7
P2.
3
P3.
6
VS
S
XTA
L1
XTA
L2
P1.
0
P1.
1
P1.
2
P1.
3
P1.
4
VS
P3.
5
HS
P2.
0
P1.
5
LCIN
LCO
UN
T
CV
BS
B3
B1
UH
F
15CLFIL
25CLFIL
FIL
P1.
6
P0.
2
P0.
1
P0.
0
P3.
7
RE
SE
T
P0.
5
P0.
7
FBK
GBGR
P4.
0
VD
D
P3.
2
VD
DA
IRE
F
P3.
1
P3.
0
P3.
3
P0.
6
51
52
48 49 5047
30313233 3435
36 37
38 39
40
41 4243
44
4546
2829
25
26
27
192021222324 18
17
16
15
12 13
1411
101
23 4
56
789
SDA5252(TEXT)SDA5222
IC850
0,1u
CC826
12V_GER.
12V_GER.
12V_GER.
+
2,2u
/100
V
C28
17
10n
CC284510n
CC2835
10n
CC2825
15p
CC
2820
0,1u
CC
820
22k
CR
100
**CR105
4,7k
CR
883
37cm
37cm
37cm37
cm4
33k
BY
T54M
10
0,561k
0,56
F
470p
/FK
P/1
600V
F
33n/630V
1N40
031N
4003
P
P
P
BY
T54M
P
PP
4,7k OIRT
+
2,2u/100V
C115
3
2
1B
+B‘
+M
+M
+H
+H
+H
+H
+H
+H+H
+H
+H
+H
+H
+H
+H
+H
+H
+H +H
+H +H +H
+H
P
P
M
M
M
M
M
M
M
M
M
M
M M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
MM
M
MM
M
M
M
M
MM
M
M
M
M
M
M
M
M
M
MM
M
M
M
M
M
M
M M M
M
MM
M
M
M
M
M
M
M
M M
M MMM
M
M M
M
M MM
M M
M M
MMM
M M
M M
M M M M
M
M
M
M
M
+A
+A
+12V
+33V
+33V
+8V
+B
G‘
+H/1
+H/1
+H/1
+H/1
+H/1+H/1+H/1+H/1
+H/1
+E
+E
27kV
RO
EH
RE
STANDART
EN
TF. B
EI 2
0/21
" TE
XT
NO
EX
ISTE
EN
MA
NC
A C
ON
N
’EX
ISTE
PA
S P
OU
RD
ELE
TED
WIT
H
SOLAM. EN CASO DE‘ APPAR. A 12VSOLO CON PER APPAR. A 12VSEUL. POUR 12V APPAREILONLY FOR 12V SETS
C66
9
L646
D64
6D
647
R647C647
R66
6
R66
7
R66
5
D66
6D
664
R66
3
T665
R661
27kV ROEHRE
NUR BEI 12V GERAETE
10k
OIR
T
(6)
+112 Volt bei 37cm ORION +105 Volt bei 37cm PHILIPS
20"/21"
w.w 29305-119.28/29
RESET
1
823.96
+124 Volt bei 15"-21"
4,3V3,3V
8V
5,8V
1,6V
0,8V
1,4V
1,4V
30
SECAM
2
6
4
5
3
1
160V
+5V
PTC
(4)
(9) (12)
(15)
(18)
+8V
10
9
8
7
6
5
KB/IR/BA
4
3
2
1
+16,5V
+12V
230V
NE
TZ
GRUNDIG Service
CUC 7303 Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
GRUNDIG Service
CUC 7303 Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
Gesamtschaltplan / General Circuit Diagram
4 - 11 4 - 12
0
CR
2840
n.v.
BC858BCT925
xx
CR
925
1
R30
3
INL
1,8k
CR2829
LS41
48
LINESTORE
LINESTORE
PLLCLOCK PROZ.
10
9
8 7 643 2
1
15 13
12
11
TDA4665T(ORIT/FR)
TDA4662T CIC105
4,7k
CR405
22k
CR
409
6,8k
R156
56k
CR
149
n.V.
22k
CR
974
5,6k
CR951
2,2k
CR
967
5,6k
CR952
1k
CR
953
75
CR
954
47
CR
968
75
CR
971
220
CR923
360
CR
911
330
CR
966
470
CR921
82
CR
922
680
CR927
2,7k
CR926
5,6k
CR
956
75
CR958
75
CR959
220
CR
957
75
CR
962
75
CR961
1k
CR
931
1k
CR
964
BA
582
CD
928
470
CR
937
BA
582
CD
929
0
330
CR
965
470
CR111
470
CR
112
330
CR
963
220
CR
960
8,2M
CR155
8,2M
CR
161
8,2M
CR
154
100
CR152
100
CR151
8,2k
CR
126
*C
R19
2
*CR191
510/
2%
CR
186
**
CR166+
1k
CR
181
10k
CR
182
750
CR147
100
CR153
12k
CR
127
560k
CR158
330
CR162
8,2k
CR
159
100k
CR
173
1,2k
CR920
GB
10k
CR
136
1
CR
141
5,1k
CR187
470
CR403
*
CR
419
*
CR408
8,2k
CR
171
10k
CR163
18k
CR407
18k
CR
167
10k
CR156
820k
CR
166
2,2k
CR
143
3,3k
CR
169
K 2,2n
C50
2
FR
US
CH
UTZ
GB
330
R511
100
CR
305
4,7k
CR
128
15k
CR
124
0
CR924
27p
CC163
0
CR
148
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
BU1
3
2
76
1
8141-812-405F923
TPS6,0MHzTPS5,5MHZ
F924
SFE6,05,5MHz
F926
6,0MHz_FR6,5MHz_OIRT
F927
SD
A
SC
L
37cm
37cm
BGR
AU
DIO
BB
AUDIO
AUDIO FBAS
R
AU
DIO
SB
BB
SB
G
B
SW
ZF_
ZFRGB SB
UE
UR
O-
AV
UD
ATA
PE
RI
BC858BCT110
CH2 CH1
3,58
MH
z
Q17
1
4,43
MH
z
Q17
2
09246-865.04TR501
BC858BCT962
BC858BCT191
BC858BCT181
BC858BCT169
*CD191
BA
582
CD
927
BA
582
CD
926
LS4148
CD501
LS41
48
CD
192
LS41
48
CD
516
LS41
48
CD
954
4,7k
CR
404
BAV21
D405
-(R-Y)
-(B-Y)
PHASISDEEM
SWITCH
1112
9
10
TDA8395N2
IC110
BC548BT511
BC637T501
10k
R41
3
ZPD
22/2
%
D51
2
ZPD
12
D51
4
ZPD4,7V
D406
FR
J5
J4
100
R41
1
2,2k
R40
8
UN
OR
M1
UFB
AS
UK
OIN
FC
158
0,1u
UD
ATA
UV
Q
BC848BCT921
BC848BCT963
BC848BCT937
BC848BCT186
L506-056
100
CR
304
+1u
/100
V
C96
6
56k
CR121
+
2,2u
/100
V
C19
1
+
470u/10V
C141
+
22u/35V
C512
0,1u
CC
147
+
10u/
50V
C14
8
+
22u/
50V
C14
9
+
2,2u/100V
C153
+
2,2u/100V
C152
+
47u/
16V
C12
7
+
4,7u/63V
C128
+
220u
/10V
C51
1
+4,
7u/6
3V
C40
8
+
1000u/35V
C412
+
10u/50V
C151+
1u/1
00V
C16
7
+
4,7u
/63V
C50
1+
100u/35V
C402
*1R
50315
01R
502
22k
CR
122
+
2,2u/100V
C129
BA
V21
D51
3
1N4936
D401
BR
U14
6
5
4
3
2
1
7
RGB
n.V.
0,22
u
F
0,18u
C513
F
/FK
P1/
1600
V
C50
6
F
22n
C50
3
F
0,22
u
C41
7
UN
OR
M1
F
*
C42
2
1n
CC
140
150p
CC951
0,1u
CC
922
0,1u
CC
921
47p
CC924
0,1u
CC
937
0,1u
CC
923
xx
CC
171
2,2n
CC973
0,1u
CC401
0,1u
CC126
0,1u
CC127
680p
CC
184
4,7n
CC
157
0,1u
CC142
0,1u
CC141
0,1u
CC
143
4,7n
CC
174
0,1u
CC
173
18p
CC
172
8,2n
CC
419
100p
CC308
150p
CC
958
150p
CC957
150p
CC956
1n
CC
501
0,1u
CC
177
1,5n
CC406
0,1u
CC
144
1n
CC
167
10n
CC
166
0,22
u
CC
403
2,7n
CC
149
390p
CC
156
0,1u
CC
146
0,1u
CC
124
37cm
n.V.
U
1k
R40
1
680
R414
390
R406
100
CR406
UR
V
UA
FC
1
R41
6
*
R41
2
2,7k
R51
3
22
R50
4
xx
CC925
VIDEOAGC IDENT.
AFC
2 3
3
H-DRIVEPAL/NTSC-DECODER
V-DRIVE
1432 6 5
11
10
9
8 7
12
13
52
51 50
49
48
47
46
45
44
43
42
4140 39 38
37
36
35 34333231 30 29 2827
2625
24
23
22
21
20
19
18
171615
14
TDA8361A(INLAND)TDA8362A(EURO)
IC150
9 87
6
5
4
3
2
1
TDA3653_B
IC400
3,3n
CC913
120
R50
6
*R
512
RO
SD
BO
SD
GO
SD
RO
SD
BO
SD
GO
SD
FBASTER
AU
DIO
ZF
AU
DIO
EU
RO
-AV
FBA
SS
C
FBA
SE
UR
O-A
V
FBA
SS
C
FBA
S
AU
DIO
EU
RO
-AV
AU
DIO
1 VS
YN
C
HS
YN
C
FBA
SE
UR
O-A
V
AU
DIO
ZF
FBA
S
AU
DIO
EU
RO
-AV
8,2uH
L924
FR/OIRT
10k
R16
6
S2055NT506
4,7
R11
8
4,7
R11
9
0,1u
CC118
0,1u
CC119
10k
CR114UP
AL
FR/OIRT
47p
CC
920
NTSC NTSC
37cm
37cm
GB
GB
37cm
100p
CC307
8,2p
CC139
1n
CC
135
76
31
F1308141-111-6038141-111-602
GB
10n
CC902
180k
CR
930
10k
CR194
ZPD5,6V
CD194
BC858BCT193
10k
CR193
37cm1,2k
R18
3 *
GB
470
CR113
GB
INL
INL+
10u/50V
C309
10
8
5
4
3
2
1
OFWK6260
F906
3
F931L9460
47k
CR
903
6,8k
CR905
470
CR
9854,7k
CR
134
4,7k
CR
941
4,7k
CR
132
22k
CR
917
1k
CR919
0
CR
944
10k
CR984
7,5k
CR
918
1,2k
CR
916
56k
CR
131
1u
L305
47k
CR306
10k
CR
130
82k
CR307
**CR902
56k
CR
138
10k
CR
901
+
10u/
50V
C92
3
0
4,7k
CR906
3-10
p
C13
6
56k
CR
135
MC14094
STROBE
DATA
CLOCK
1615
14
13
12
11
1098
7
6
5
4
3
2
1
CIC130ZF ZF
_
EN
A
LOGICAGC2
1
14
1312 11
10
9
8
7
6
5
4
3
STV8225
IC950
BC858B
CT919
BA582
CD134
BA582
CD942
BA582
CD944
BA
582
CD
901
BA
582
CD
902
BA582
CD941
BA582
CD943
UN
OR
M1
BC848BCT917
BC848BCT916
BC848BCT901
22p
CC
136
+
4,7u/63V
C922
+
10u/
50V
C91
1
+
22u/25V
C921
+220u/10V
C302
BR
U12
0
10k
CR137
FR
8140-533-605F901
0,1u
CC901
1n
CC
134
0,1u
CC944
0,1u
CC926
0,1u
CC130
U
+
22u/
16V
C92
4
10k
CR133
AU
DIO
1
xx
L302
OIR
T
3,3p
CC906
FR/OIRT
FR
AG
C
UH
F
B3
B1
M15
M14
M13
M12
ZF
ZF
6 7
8
9
10
11
12 13 14 15 12
345
PHILIPS-TUNER
BA582
CD135
0
CR904
+
220u/10V
C303
xxL301
10u
L303 0
CR
309
0
CR
907
FRn.v.
1k
CR
139
390
CR168
U25
Hz
LS41
48
CD
181
n.v.
2,7M
CR
174
5,6M
CR
175
+
2,2u
/100
v
C14
5
n.V.
n.v.
10n
CC
930
HS
YN
C
CUC7305
CU
C73
05
CUC7305
4,7u
L912
3,3n
CC
912
100k
CR
912
BC848BCT915
560k
CR
913
470
CR
915
UA
UD
IO
OIRT
+
2,2u/100V
C115
+H
+H
+H
+H
+H
+H
+H
M
M
M
M
M
M
M
M
M
M
M
M
M
MM
M
M
M
M
M
MM
M M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
MM
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M M
M
M
M
M
MM
MM
M
M
MM
M M M
MM
M
M
M
M
M M
M
M
M
MM
MM
M
M
M
M
M M M
M
M
M M
M M M
M
M
M
M
M
M
+D
+D
+B/1
+5V
+12V +33V
+8V
+B
+B
+B
+B
+B
+B
+B
+B
+B
+B
+B
+E
+E
+E
+E
+E
+E
+E
+E
+E
+E
+E
+E
SOLAM. PREVISTO PARASOLO PREVISTOPREVUONLY IF REQUIRED
)(
(18k
)
(0)
CUC 7303 CUC 7303 F
*
47u/50V
nur vorgesehen!
UV1343 GB (UHF only)UV1315 INL. (PAL)
OFWK6260(FR)
OFWJ1952(GB)
fuer CC901O
IRT)
(NO
RM
1 be
iN
OR
M4
1
2 5
4
OFWK6255G(OIRT)OFWG1962G(INL)
**
UN
D G
B
R41
4
3,9V
3,9V
2,5V
1V
1,5V
1,5V
5,3V
3,8V
7,7V
3,8V
4,4V
2,5V
3V 2,4V
3,5V
1,7V
1,7V
1,7V8V8V
5,8V
5,8V
5,4V
2,7V
2,5V
1,8V
1,8V
1,8V
3,8V
0,8V
2,8V
3,8V
2V4,3V6,6V2,8V
1,6V
5,8V
1,5V
1,5V
1,3V
3,4V
3,4V
3,4V
0,3V
2V
9V
4V
4V
3V
5,1V
5,1V
29
28
21
23
22
24
25
26
19
16
17
15
13
14
20
18
10SECAM
11
9
12
7
8
(2,7k)
4,5MHzn. b. US-NORM
MK
T
fuer
CD
926
VE
RS
C.I.
TU
BE
CA
THO
D
A L
A P
LAC
A-Z
OC
ALO
TR
CA
LLA
PIA
STR
A C
INE
SC
.
TO C
AR
T B
AS
EZU
R B
ILD
RO
HR
PLA
TTE
BE
I IN
L.
VERTIKAL
F
VERT.
JOCH
AB
C
D
E
F
AB
C
D
E
F
GRUNDIG Service
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams CUC 7303
GRUNDIG Service
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams CUC 7303
Gesamtschaltplan / General Circuit Diagram
4 - 13 4 - 14
xx
CR
325
n.v.
2,2n
CC
383
3,3n
CC381
CR
382
120
CR
381
220
3
2
1
CH
3
2
1
KH1
2
3
4
V2BK001
BR
532
1
2
LS
4,7k
CR323
2,7k
CR
328
4,7
CR
331
8,2
R33
7
100
CR326
L381
-014
1k
CR541
10k
CR
322
1,8k
CR321
BA
V21
D82
6
37cm
SB
UN
FM
UTE
10/7
W
R53
2
+
220u
/10V
C32
5
2,2k
CR324
10u
L526
*
L531
ZPD8,2V
D323
BC548BT523
BC848BCT325
5,6k
CR327
+
1000
u/35
V
C44
6
+
22u/
350V
C54
3
+
22u/
16V
C32
3
+
470u/10V
C331
+
470u/16V
C327
+
22u/
16V
C32
6
*1R
531
*2/4
R53
3
6,81
R526
*XR
554
BYV16
D543
1N4936
D444
BA157
D524
BR546
BR526
390p
C444
F
0,68u/MKS4/160V
C522
F
18n/63V/FKP2
C527
F
/MKP4/160V
C526
F0,
22u
C54
2F0,
22u
C54
1
F
0,68
u/M
KC
4SV
21
C53
2
0,1u
CC
331
0,1u
CC328
3,3n
CC
3220,1u
CC321
*
R542
1k
CR
523
1,2k
R546
1M/M
GW
R52
2
1,5k
R553
10/1W
R543
10k
R524
100n
CC382
L
I
G
C
F
H
B
A
GND
HS
F
G2
U
U
29201-TR550
33k
R52
1
5
4
3
2
1
BR-HZ
09246-L533
220u
L543
TDA7233
8
7
6
5
4
3
2 1
IC320
37cm
37cm
37cm
F
68k
CR
329
37cm
37cm
BR205
KH
KH
00
1
CR203
+H
+C
+C
M
M
M
M
M
M
M
M
MM
M
M M
M
M
M
M
M
MM
M
M
M
M
M
M
M
M
M
UF
+A
HS
+D
UG2
KH
KH
KH
KH
+B
+B
+B
G‘
BR
-PLA
TTE
131196
A LA PLACA-ZOCALO TRC
A L
A P
LAC
A-Z
OC
ALO
TR
C
ALLA PIASTRA CINESC.
ALL
A P
IAS
TRA
CIN
ES
C. VERS C.I. TUBE CATHOD
VE
RS
C.I.
TU
BE
CA
THO
D
TO CART BASE
TO C
AR
T B
AS
E
ZUR BILDROHRPLATTE
0,51 0,51 0,51 0,51 0,51 0,51 0,51 0,511 1R503
??
*
*
*
LS4148LS4148 LS4148 LS4148 LS4148 LS4148 LS4148LS4148
100k 100k 100k
100k 100k
100k
100k
100k
100k
100k
100k
100k
100k
100k
100k100k100k100k100k100k100k100k
110k110kCR856
15k15kCR192
CD191
100k 100k00CR191
39k 39k 39k 39k 39k 39k 39k 39k68k 68kR683
390
3,3k3,3k3,3k3,3k
1,8k1,8k1,8k1,8k
4,7k 4,7k 4,7k 4,7k 4,7k 4,7k
3,9k 3,9k 3,9k 3,9k 3,9k 3,9k
CR419
CR408
100u
270
360/2%
0,15u
1,8
8,3n
-838.51
-114.95
0,33u/MKP4
2,2 OHM/2W
20" SAMSUNG
2,2k
1k
0,82
29201-513.97
8311-200-010
10k
820 OHM
47n/MKS 2
820 OHM/2W
-031.54
*
C626
CR2813
47u 47u 47u 47u 47u 47u 47u 47u 100u
0 0 0 0 0 0 270270270
19" 21"
0,15u 0,15u 0,15u 0,15u 0,15u 0,15u0,15uC601 0,22u 0,22u
1,5k/4W
-850.51
29201-513.97 29201-513.97 29201-513.97 29201-513.97 29201-513.97
360/2%360/2%360/2% 360/2%
1,51,8 1,8 1,8 1,8 1,8 1,8 1,8 1,8
5,1 OHM/1W
21" SN PHI
R412
-114.95
0,33u/MKP4
20"16" ORION17"15"14" PHILIPS14" ORION
470/2%470/2%
-115.95-115.95 -115.95-115.95-115.95-115.95L531
R653
R666
R183
2,2k 2,2k 2,2k 2,2k 2,2k 2,2k2,2k1,5k
1k 1k1k1k1k1k 1k
0,82 0,820,820,820,820,82 0,821
1,1k1,1k
1
29201-513.97 29201-513.97
3,9k
29201-512.97 29201-514.97
7,5 OHM/1W
-653.01
8311-200-010 8311-200-0108311-200-010 8311-200-0108311-200-020 8311-200-020 8311-200-020 8311-200-020 8311-200-020R609
7n
4,7 OHM/1W4,7 OHM/1W4,7 OHM/1W 4,7 OHM/1W 4,7 OHM/1W4,7 OHM/1W
10k 10k10k10k 10k 10k10k13k13k
7,5n
C422
3,3 OHM/1W
820 OHM 820 OHM820 OHM 820 OHM 820 OHM820 OHM 820 OHM
6,8n 6,8n 6,8n6,8n7,8n 7,8n
47n/MKS 2
R542
7,5n
47n/MKS 2 47n/MKS 2 47n/MKS 247n/MKS 2 47n/MKS 2 47n/MKS 247n/MKS 2
R554
C526
R531
C506
L533
TR550
R512
0,42u/MKP40,26u/MKP4 0,26u/MKP4 0,26u/MKP40,42u/MKP40,26u/MKP40,42u/MKP40,42u/MKP4
820 OHM/2W820 OHM/2W1,5k/4W 1,5k/4W 1,5k/4W1,5k/4WR533
TR601
-850.21 -850.21 -850.21-838.21 -838.2109246-850.21
-031.54 -031.54-031.54 -031.54 -031.54-031.54 -031.54-031.55
KH/CH
1
2
3
4
5
6
7
8
ca. 190V/15-21"ca. 125V/14"
SOLAM.CON 20" SAMSUNGSOLO CON 20" SAMSUNGSEUL.POUR 20" SAMSUNGONLY WITH 20" SAMSUNGNUR BEI 20" SAMSUNG
412.3129200-
27
470u
/35V
I
C
G
BEI 37cm ORIONTR550
(INTERN)
10
9
8
765
4
3
2
1
/25V
circuits are allowed to be put out of operationonly for a short time.
or the picture tube the integrated protectiveTo avoid consequential damages to the chassis
the precise adjustment of the +A power supply.and thus the developing X-radiation depends onThe high tension for the picture tube
duerfen nur kurzzeitig ausser Betrieb
ist abhaengig von der exakten Einstellungder Netzteilspannung +A.
am Chassis oder an der Bildroehre zu vermeiden.gesetzt werden, um Folgeschaeden
Schutzschaltungen im Geraet
und die damit auftretende RoentgenstrahlungDie Hochspannung fuer die Bildroehre
COLLEGAM. VISTI DI SOTTO CONN. VUES DE DESSOUS CONN. BOTTOM VIEW ANSCHL. V. UNTEN GESEHEN
CONEXIONES VISTAS POR DEBAJO
M
L
K
I
H
GF
E
D
C
B
A TR 550
HOR.
JOCH
J3
J1
F
F
RESERV. EL DEREC. DE MODIFIC.CON RISERVA DI MODIFICASOURS RESERVE DE MODIFICSUBJECT TO ALTERNATEAENDERUNGEN VORBEHALTEN
AB
C
D
E
F
Bildrohrplatte / CRT Panel 29305-022.16
29304-722.73/2l(03)
5
0123456789
E B
T781
EB
T741
EB
T761
E B
T736
EB
T756
EB
T776
BR751
BR001
BR002
C716
C71
7C731
C781
C714
R739
R75
9
R779
R733
R75
3
R77
3
17
ST-
RG
B
1
4
5
6
7
8
910
11
12
BR
700
R771
R751
BR003
15 ST-BR
29304-722.73/4b(02)
UG2
6 54
2
3
1
29304-722.73/2l(03)5
0123456789
CD
762
CD734C
D742
CD
781
CC
754
CC
762
CC
783 CC
742
CC
782
CC
761
CC782A
CC774
CC734
CB
R001
CBR002
CBR004
CBR003
CR742
CR741
CR
736CR734
CR
756
CR
762
CR764
CR
751CR774
CR
761
CR
776
CR
781
CR782
CR
752C
R763
CR
771
CR784
CR
783
CR732
CR777 CR
754CR772
CR731
CR737CR735
CR
754A
CR731A
CR
744
0V
1V/cm, 20µs/cm1
0V
1V/cm, 20µs/cm2
0V
1V/cm, 20µs/cm3
0V
50V/cm, 20µs/cm4
0V
50V/cm, 20µs/cm5
0V
50V/cm, 20µs/cm6
Bestückungsseite, Ansicht von obenComponent side, top view
Lötseite, Ansicht von untenSolder side, bottom view
CUC 7303 Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
GRUNDIG Service 4 - 15
Bildrohrplatte / CRT Panel 29305-022.16
*T7
81
BF4
21T7
36
BF4
21T7
56
BF4
21T7
76
*T7
41
0
CR744
240
CR742
1k
CR
736
270p
CC
734
1k
CR
734
680p
CC
762
1k
CR
756
240
CR762
0
CR764
1k
CR
774
1k
CR
776
240
CR782
1,2k
CR
752
5,1k
CR763
0
CR784
5,1k
CR783
2,2k
CR732
LS41
48
CD
781
820p
CC
742
390p
CC
782
390p
CC
782A
220p
CC
754
270p
CC
774
470
CR
777
LS41
48
CD
762
LS41
48
CD
734
LS41
48
CD
742
+
4,7u/250V
C731
22n
C71
4
1,5k
R73
9
R77
3
*
1,5k
R75
9
1,5k
R77
9
1k
CR
754
1,2k
CR
772
R73
3
*
R75
3
*
1kR771
*
CR
781
M
M
MM
M
MM
MM
M
M
M M
12345
BR
7 123456
RG
B
*
CR
761
330
CR
731
*
CR
741
M
+
10u/50v
C781
1kR751
R
U/F
OC
G
U/S
GB
+12V SW
+C
*T7
61
F
4,7n
/1kV
C71
6
10k
CR735
156 78 9 1011 12 0
+1
+1
+1
+1 +1
+2
+2+2
+2
+2
+2
+2
+2
1207
96
8,2k
2W02
2.16
2930
5-02
2.16
(15"
-21"
)29
305-
022.
75108 9116
SM
ALL
-N
EC
K
022.
XX
65
4
123
BV
0411
*
2,7k
BF4
22
BF8
71
10k
12k
CR
781
CR
761
CR
741
T781
T761
T741
R77
3R
753
R73
3
(130
V) 1
4"(2
00V
) 15"
-21"
VG V
B
90
1
0(1
2V)
AL
TRA
NS
F. D
E L
INE
AS
ALL
O T
RA
SF.
DI R
ETE
VE
RS
TR
AN
SF.
ALI
ME
NT
TO L
INE
TR
AN
SFO
RM
ER
ZUM
ZE
ILE
NTR
AFO
PLA
CA
ZO
CA
LO T
RC
PIA
STR
A C
INE
SC
.C
.I. T
UB
E C
ATH
OD
.C
RT
PA
NE
L
BIL
DR
OH
RP
LATT
E
B
GR
L520
PU
NK
TLE
UC
HT
U
HU
AL
CH
AS
ISA
L TE
LAIO
VE
RS
CH
AS
SIS
TO C
HA
SS
ISZU
M C
HA
SS
ISV
J
J
HJ
14 235678
ZUM
CH
AS
SIS
TO C
HA
SS
ISV
ER
S C
HA
SS
ISA
L TE
LAIO
AL
CH
AS
IS
AL
CH
AS
ISA
L TE
LAIO
VE
RS
CH
AS
SIS
TO C
HA
SS
ISZU
M C
HA
SS
IS
Servicearbeiten nach Bausteinwechsel: siehe Abgleich Seite 3-1Servicing work after replacing the module: see alignment page 3-2
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams CUC 7303
4 - 16 GRUNDIG Service
Bildrohrplatte / CRT Panel 29305-022.14/.15
*T7
81
BF4
21T7
36
BF4
21T7
56
BF4
21T7
76
*T7
41
0
CR744
270
CR742
1k
CR
736
220p
CC
734
1k
CR
734
390p
CC
762
1k
CR
756
270
CR762
0
CR764
1k
CR
774
1k
CR
776
270
CR782
1,2k
CR
752
5,1k
CR763
0
CR784
5,1k
CR783
2,2k
CR732
LS41
48
CD
781
390p
CC
742
390p
CC
782
120p
CC
782A
220p
CC
754
220p
CC
774
470
CR
777
LS41
48
CD
762
LS41
48
CD
734
LS41
48
CD
742
+
4,7u/250V
C731
22n
C71
4
1,5k
R73
9
R77
3
*
1,5k
R75
9
1,5k
R77
9
1k
CR
754
1,2k
CR
772
R73
3
*
R75
3
*
1kR771
*
CR
781
M
M
MM
M
MM
MM
M
M
M M
12345
BR
7 123456
RG
B
*
CR
761
150
CR
731
*
CR
741
M
+
10u/50v
C781
1kR751
R
U/F
OC
G
U/S
GB
+12V SW
+C
13 4 5 67 89 10
BR
-SO
CK
EL
12
UG
2
*T7
61
F
4,7n
/1kV
C71
6
10k
CR735
+1
+1
+1
+1 +1
+2
+2+2
+2
+2
+2
+2
+2
2930
5-02
2.15
21"
2930
5-02
2.14
14"
2408
95
65
4
123
BV
0411
BV
0617
*
022.
14
022.
15
2,7k
BF4
22
BF8
71
10k
12k
CR
781
CR
761
CR
741
T781
T761
T741
R77
3R
753
R73
3
(130
V) 1
4"(2
00V
) 15"
-21"
VG V
B
SO
LAM
. PR
EV
ISTO
PA
RA
SO
LO P
RE
VIS
TOP
RE
VU
ON
LY IF
RE
QU
IRE
DN
UR
VO
RG
ES
EH
EN
**
**
90
654 8397 1
0(1
2V)
AL
TRA
NS
F. D
E L
INE
AS
ALL
O T
RA
SF.
DI R
ETE
VE
RS
TR
AN
SF.
ALI
ME
NT
TO L
INE
TR
AN
SFO
RM
ER
ZUM
ZE
ILE
NTR
AFO
PLA
CA
ZO
CA
LO T
RC
PIA
STR
A C
INE
SC
.C
.I. T
UB
E C
ATH
OD
.C
RT
PA
NE
L
BIL
DR
OH
RP
LATT
E
B
GR
L520
PU
NK
TLE
UC
HT
U
HU
AL
CH
AS
ISA
L TE
LAIO
VE
RS
CH
AS
SIS
TO C
HA
SS
ISZU
M C
HA
SS
ISV
J
J
HJ
14 235678
ZUM
CH
AS
SIS
TO C
HA
SS
ISV
ER
S C
HA
SS
ISA
L TE
LAIO
AL
CH
AS
IS
AL
CH
AS
ISA
L TE
LAIO
VE
RS
CH
AS
SIS
TO C
HA
SS
ISZU
M C
HA
SS
IS
Servicearbeiten nach Bausteinwechsel: siehe Abgleich Seite 3-1Servicing work after replacing the module: see alignment page 3-2
CUC 7303 Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams
GRUNDIG Service 4 - 17
Bildrohrplatte / CRT Panel 29305-022.14/.15
2L(03)
04
722.72 29304-
B E
T781
B E
T741
B EBE
T736 BE
B E
T776
C71
6
R73
9
R759
R73
3
R75
3
R77
3
R751
R771BR
-SOCKE
L
C73
1C781
R779
BR
771
BR
751
C715
51
BR
7 1
RGB
C71
4
2930
4-72
2.72
/4B
(03)
UG2
6 5 4
23 1
2L(03)
04
722.72 29304-
CR
772
CR754
CR
777
CR
732
CR783
CR
784
CR
775
CR763
CR752
CR
782
CR
781
CR
776
CR
761
CR774
CR
755
CR
764
CR
762
CR
756 CR
734
CR
736
CR
735
CR
741
CR
742
CR
744
CR751
CC
775
CB
R001
CBR002
CBR003
CB
R004
CB
R005
CB
R006
CC
755
CC
774
CC
754
CC
782A
CC761
CC
782
CC742
CC783CC762
CC
734C
R731
CD
742 CD
734
CD
762
CD
781
CR
771
CC
732
29304-722.72/4LS(02)
0V
1V/cm, 20µs/cm1
0V
1V/cm, 20µs/cm2
0V
1V/cm, 20µs/cm3
0V
50V/cm, 20µs/cm4
0V
50V/cm, 20µs/cm5
0V
50V/cm, 20µs/cm6
Bestückungsseite, Ansicht von obenComponent side, top view
Lötseite, Ansicht von untenSolder side, bottom view
Platinenabbildungen und Schaltpläne / Layout of the PCBs and Circuit Diagrams CUC 7303
4 - 18 GRUNDIG Service
Prozessorplatte / Processing Board
6,8u
/2%
L1
33p/
1%
CC
2
33n
CC
11
100p
/1%
CC
1
M
OE
CE
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
28
15 16 17 18 19
20
21
22
232425 26 27
14
1234567891011 12 13
27C
512
IC1
137 8 9 10 11 121 2 3 4 5 6137 8 9 10 11 121 2 3 4 5 6137 8 9 10 11 121 2 3 4 5 6137 8 9 10 11 121 2 3 4 5 6
6,8k
CR
14
M
910
1112
1314
1516
1718
1920
2122232425262728293031323334353637383940
4142
4344
4546
4748
4950
5152
5354
5556
5758
5960
61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80
12
34
56
78
SD
A52
50
IC2
M
M
M
33n
CC
14
18MHz
Q3
6,8k
CR
11
33CR
3
M
15p
CC3
56p
CC4
M
8,2k
CR
12
M
0,22
u
CC
12
M
270k
CR
16
82k
CR13
M
K
0,1uCC
6
05
05 32
32
43
4303
03
D7
D7
D6
D6
31
31
A1
A1
A1
A1
D5
D5
D4
D4
A14
A14
A13
A13
A12
A12
01
01
23
23
22
22
21
21
D0
D0
20
20
D1
D1
D1
19
19
18
18
17
17
16
16
D2
D2
15
15
45
45
A11
A11
1414
14 40
40
47
47
48
48
49
49
D3
D3
50
50
51
51
A10
A10
26
26
35
35 41
41
A9
A9
11
11
A8
A8
10
10
A3
A3
37
37
+5V
+5V
44
44
A7
A7
A6
A6
A15
A15
42
42
292929
34
34
36
36
33
33
A2
A2
A4
A4
02
02
A5
A5
04
04 2828
52
52
46
46
09
09
08
08
07
07
3030
25
25
06
06 2727
272424
A0
A0
1709
96
MQ
F80
PR
OZE
SS
OR
-PLA
TTE
293
05-1
19.2
8 (M
IT T
EX
T)
-
119.
29
ALE
P1-0
P1-1
P1-2
P2-
0
P2-
1
P2-
2
P2-
3
D7
D6
D0
D5
D1
P0-3
P0-4
D4
D2
D3
RT
GR
BL
BLAN
COR
VSS
VDD
LCIN
LCOUT
HS/SC
VS/P4-7
P0-0
P0-1
P0-2
P3-1
A16
A17/P4-0
RST
XTAL1
XTAL2
VDD
VSS
P1-3
P1-4
P1-5
P1-6
P1-7
P3-0
P3-
2
P3-
3
P3-
4
P3-
5
P3-
6
P3-
7
CV
BS
IRE
F
VD
DA
FIL2
FIL1
FIL3
VS
SA
P0-
7
P0-
6
P0-
5
PR
OC
ES
SIN
G B
OA
RD
PLA
QU
E C
ALC
ULA
TEU
R
PLA
CA
CA
LCO
LAD
OR
PIA
STR
A C
ALC
OLA
TOR
E
SO
LAM
.PR
EV
ISTO
SO
LO P
RE
VIS
TOP
RE
VU
ON
LY IF
RE
QU
IRE
DN
UR
VO
RG
ES
EH
EN
**
**
A15
A14
A12
A13
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
-
119.
30/.3
1
CU
C 7303
Spare P
arts List
GR
UN
DIG
Service
5 - 1
ErsatzteillisteSpare Parts List
7 / 96 CUC 7303
D Btx * 32700 #
POS. NR. ABB. SACHNUMMER ANZ.
POS. NO. FIG. PART NUMBER QUA.BEZEICHNUNG DESCRIPTIOND GB
0001.000 8140-601-610 TUNER UV1315/I (SPANNUNGSSYNTH.) TUNER UV1315/I (VOLTAGE)0001.000 8140-601-611 TUNER UV1343/I (SPANNUNGSSYNTH.) TUNER UV1343/I (VOLTAGE)
.08/.09/.18/.22 .08/.09/.18/.220002.000 S 29703-291.21 NETZSCHALTER POWER SWITCHWW. S 29703-291.31 NETZSCHALTER POWER SWITCH0003.000 29502-460.29 ZF-ABDECKUNG IF COVER0004.000 S 29303-399.51 NETZ EINBAUGERAETESTECKER POWER BUILT-IN APPLIANCE0005.000 29303-390.43 KOPFHOERERBUCHSE HEADPHONE SOCKET0006.000 29303-119.04 EURO-AV BUCHSE 21-POL PERI-SOCKET 21 PIN
29305-119.28 PROZESSORPLATTE .07 PROCESSOR BOARD .07KEIN E-TIL NO SPARE PART
29305-119.30 PROZESSORPLATTE .18 PROCESSOR BOARD .18KEIN E-TIL NO SPARE PART
0007.000 S 29201-360.01 ANODENKAPPE M. HOCHSPG.-KABEL .06/.09 C.R.T. SOCKET W. HIGH-VOLTAGE CABLE .06/.090007.000 S 29201-650.01 ANODENKAPPE M. HOCHSPG.-KABEL C.R.T. SOCKET W. HIGH-VOLTAGE CABLE
.05/.08/.21/.22 .05/.08/.21/.220008.000 S 09621-113.02 2 SICHERUNGSHALTER FUSE HOLDER0009.000 29703-357.11 2 TASTSCHALTER +/- KEY SWITCH +/-0011.000 29303-153.16 MONTAGECLIP T665/IC676/690 MOUNTING CLIP T665/IC676/6900012.000 29303-153.02 MONTAGECLIP T506 MOUNTING CLIP T5060013.000 29303-153.03 MONTAGECLIP IC400 MOUNTING CLIP IC4000014.000 29303-156.20 FOLIE WAERMELEITEND IC676 FOIL HEAT CONDUCTING IC6760015.000 29303-156.23 FOLIE WAERMELEITEND T506 FOIL HEAT CONDUCTING T506
WW. = WAHLWEISE WW. = OPTIONAL
SACH-NR. / PART NO.: 29704-002.01/.03/.04/.05/.06/.07/.08/.09/.12/.14/.16/.17/.18/.21/.22/.24
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
C 412 8452-996-187 ELKO 1000UF 20% 35VC 446 8452-996-187 ELKO 1000UF 20% 35VC 506 S 8515-911-070 FOKO FKP1/4 6800PF 3,5% 1C 601 S 8599-990-025 MP 3 0,15UF 20% 250VW AVC 603 S 8660-098-234 SI-KERKO B-SS 1000PF 20%C 604 S 8660-098-234 SI-KERKO B-SS 1000PF 20%C 621 8650-081-125 HV-KERKO 1000PF 20% 1KVC 622 8650-081-125 HV-KERKO 1000PF 20% 1KVC 623 8650-081-125 HV-KERKO 1000PF 20% 1KVC 624 8650-081-125 HV-KERKO 1000PF 20% 1KVC 627 S 8660-098-238 SI-KERKO B-SS 2200PF 20%C 669 8515-911-060 FOKO KF #7 1000PF 10% 160C 671 8650-081-111 HV-KERKO 270PF 20% 2KVC 681 8650-067-046 HV-KERKO 100PF 20% 1KVC 819 8140-540-104 EMIFIL 0,1 UF
CD 191 8325-004-148 SMD DIODE LS 4148CD 192 8325-004-148 SMD DIODE LS 4148CD 194 8309-455-056 MELF-Z DIODE 5,6 C 0,5 WCD 501 8325-004-148 SMD DIODE LS 4148CD 516 8325-004-148 SMD DIODE LS 4148CD 654 8325-004-148 SMD DIODE LS 4148CD 656 8325-004-148 SMD DIODE LS 4148CD 673 8325-004-148 SMD DIODE LS 4148CD 734 8325-004-148 SMD DIODE LS 4148
CD 742 8325-004-148 SMD DIODE LS 4148CD 762 8325-004-148 SMD DIODE LS 4148CD 781 8325-004-148 SMD DIODE LS 4148CD 830 8325-004-148 SMD DIODE LS 4148CD 844 8325-004-148 SMD DIODE LS 4148CD 851 8325-004-148 SMD DIODE LS 4148CD 954 8325-004-148 SMD DIODE LS 4148CD 2827 8325-004-148 SMD DIODE LS 4148CD 2829 8325-004-148 SMD DIODE LS 4148
CIC 105 8305-844-662 SMD IC TDA4662T/V2 PHI/
CT 110 8301-003-858 SMD-TRANS.BC 858 BCT 169 8301-003-858 SMD-TRANS.BC 858 BCT 181 8301-003-858 SMD-TRANS.BC 858 BCT 186 8301-004-848 SMD-TRANS.BC 848 BCT 191 8301-003-858 SMD-TRANS.BC 858 BCT 193 8301-003-858 SMD-TRANS.BC 858 BCT 325 8301-004-848 SMD-TRANS.BC 848 BCT 826 8301-004-848 SMD-TRANS.BC 848 BCT 840 8301-004-848 SMD-TRANS.BC 848 BCT 916 8301-004-848 SMD-TRANS.BC 848 BCT 917 8301-004-848 SMD-TRANS.BC 848 BCT 921 8301-004-848 SMD-TRANS.BC 848 BCT 962 8301-003-858 SMD-TRANS.BC 858 B
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
BEZEICHNUNG
DESCRIPTION
SACHNUMMER
PART NUMBER
POS. NR.
POS. NO.
CT 963 8301-004-848 SMD-TRANS.BC 848 BCT 2821 8301-003-858 SMD-TRANS.BC 858 BCT 2825 8301-003-858 SMD-TRANS.BC 858 BCT 2831 8301-003-858 SMD-TRANS.BC 858 BCT 2835 8301-003-858 SMD-TRANS.BC 858 BCT 2845 8301-003-858 SMD-TRANS.BC 858 BCT 2850 8301-534-269 SMD TRANS PMBT2369
D 323 8309-720-082 Z DIODE 8,2 C 0,5WD 401 8309-210-138 DIODE 1N4936/1SR124-400D 405 8309-200-021 DIODE BAV21 ITT/ TFKD 406 8309-720-048 Z DIODE 4,7 C 0,5WD 444 8309-210-138 DIODE 1N4936/1SR124-400D 512 8309-720-221 Z DIODE 22 B 0,5WD 513 8309-200-021 DIODE BAV21 ITT/ TFKD 514 8309-720-112 Z DIODE 12 C 0,5WD 524 8309-201-005 DIODE BA157D 543 8309-204-268 DIODE BYV16 TEMIC/ BYV96D 621 8309-215-127 DIODE 1 N 4007 -GAD 622 8309-215-127 DIODE 1 N 4007 -GAD 623 8309-215-127 DIODE 1 N 4007 -GAD 624 8309-215-127 DIODE 1 N 4007 -GAD 661 8309-516-754 DIODE BYT53B TFK/ EGP10BD 662 8309-201-005 DIODE BA157D 663 8309-720-036 Z DIODE 3,6 C 0,5WD 664 8309-215-010 DIODE 1 N 4003 -GAD 666 8309-215-010 DIODE 1 N 4003 -GAD 667 8309-201-005 DIODE BA157D 668 8309-516-752 DIODE BYT53G TEMICD 671 8309-204-050 DIODE BY297 FAGOR/ BYW33D 682 8309-204-060 DIODE BY299 FAGOR/ BYV37D 683 8305-306-001 IC ZTK 33 B DPD ITTD 826 8309-200-021 DIODE BAV21 ITT/ TFKD 1806 8309-944-601 LE DIODE TLHR 4601 TFK
F 130 8141-111-602 FILTER 7X7 602 FARBE 666F 906 8319-001-956 OFW G 1962 SIE/SCF 114F 923 8141-112-405 FILTER 7X7 405F 924 8602-755-021 CER.TRAP 21 TPS 5,5 MBF 926 19203-065.97 KERAMIK-FILTER 40
IC 1 19798-505.01 IC 27C512-200 PROG.KPL.IC 150 8305-338-362 IC TDA8362A(N3)IC 320 8305-337-233 IC TDA7233 SGSIC 400 8305-343-653 IC TDA 3653 BIC 630 8305-267-842 IC UC3842N/AN SGS/MOTIC 676 8305-204-317 IC LM 317 T NSC/MOT/IC 690 8305-205-703 IC MC 7805 CTIC 810 8305-367-530 IC TFMS 5300IC 820 8305-210-065 IC MC 33164 P-5RPIC 830 8305-602-401 IC X 24 C 02 P XICORIC 850 8305-158-552 IC SDA5252A001 SIEIC 2807 8305-362-114 IC TEA 2114
L 303 8140-526-964 DR S 10UH 5% RM5L 305 8140-526-962 DR S 1UH 5% RM5L 381 8104-982-014 DAEMPFUNGSPERLE/
DAMPING BEADL 506 8104-982-056 FERRITPERLE HF 70 BTL/
FERRITE BEADL 526 8140-526-361 DR 0411 10UH 5%L 533 09246-850.51 ZB-SPULE (90) COLOR/COILL 531 29203-115.95 LINEARITAETSREGLER (90)/
LINEARITY CONTROL
L 543 8140-526-032 DR AX 0411-GA 220UHL 601 S 29500-826.97 FUNKENTSTOERDROSSEL RK19/
INTERFERENCE SUPPR. COILL 819 8104-982-051 FERRITPERLE HF 55 BTL/
FERRITE BEADL 2836 8140-522-922 DR ST 0411 6,8UH 2% SIE
Q 172 8382-136-004 QUARZ #136 2A 4,433619MHZQ 857 8602-331-155 KERRES #155 18MHZ
R 118 S 8701-121-017 KSW SI B 4,7 OHM 5%R 119 S 8701-121-017 KSW SI B 4,7 OHM 5%R 166 8796-103-151 ESTR P6A 10 KOHM LIN N6R 337 S 8701-121-023 KSW SI B 8,2 OHM 5%R 408 8796-103-140 ESTR P6A 2,2 KOHM LIN N6R 411 8796-103-109 ESTR P6A 100 OHM LIN N6R 412 S 8700-329-007 KSW NB 0207 1,8 OHM 5%R 412 S 8700-329-005 KSW NB 0207 1,5 OHM 5%R 413 8796-103-151 ESTR P6A 10 KOHM LIN N6R 416 S 8700-329-001 KSW NB 0207 1 OHM 5%R 502 S 8705-329-070 MOW 0411 150 OHM 10%R 503 8705-226-991 MOW 0411 0,51 OHM 10%R 504 S 8701-121-033 KSW SI B 22 OHM 5%R 513 S 8700-329-083 KSW NB 0207 2,7 KOHM 5%R 522 8710-338-145 MGW AX 1 MOHM 5% VR 37R 524 S 8700-121-297 KSW 0207 10 KOHM 5%R 526 S 8705-329-221 MOW 0411 6,8 OHM 10%R 531 S 8705-221-271 MOW 0411 820 OHM 10% SXAR 533 S 8705-279-077 MOW 0922 1,5 KOHM 5% DRAR 543 S 8705-329-025 MOW 0411 10 OHM 5% DRAR 554 S 8705-329-017 MOW 0411 4,7 OHM 5% DRAR 609 S 8311-200-020 PTC RM5 B59.250C1080 SIER 621 8311-005-017 NTC 4,7 OHM 30%R 627 S 8765-049-161 MSW 0414 4,7 MOHM VDE BER 633 S 8705-360-353 MOW 0617 56 KOHM 10% SXSR 654 8790-050-025 ESTR.SK10-A 470 OHM LINR 664 S 8705-369-043 MOW 0617 56 OHM 5%R 669 8705-279-065 MOW 0922 470 OHM 5% DRAR 681 S 8705-369-099 MOW 0617 12 KOHM 5%R 685 S 8700-329-029 KSW NB 0207 15 OHM 5%
SI 600 S 8315-617-006 SI 5X20 T2,5A L 250VSI 671 S 8315-621-027 LOET-SI.-GR 2,5 A/T
T 501 8303-285-637 TRANS.BC 637T 506 8302-900-020 TRANS S2055N TOST 511 8303-205-548 TRANS BC548BT 523 8303-205-548 TRANS BC548BT 665 8302-422-184 TRANS MJF18004C MOT/ BULT 686 8303-273-337 TRANS.BC 337-25T 736 8303-406-421 TRANS.BF 421 E6323SIE/PHIT 756 8303-406-421 TRANS.BF 421 E6323SIE/PHIT 776 8303-406-421 TRANS.BF 421 E6323SIE/PHITR 501 09246-863.04 TREIBERTRAFO/
DRIVER TRANSFORMERTR 550 S 29201-031.54 DIODEN-SPLIT TRAFO KPL./TR 550 S 29201-031.55 DIODEN-SPLIT TRAFO KPL. .06 /TR 550 S 29201-653.01 DIODEN-SPLIT TRAFO KPL. .05 /
DIODE SPLIT TRANSFORMER,CPL.TR 601 S 29201-513.97 TRAFO SPERRWANDLER KPL./TR 601 S 29201-514.97 TRAFO SPERRWANDLER KPL. .06/TR 601 S 29201-512.97 TRAFO SPERRWANDLER KPL. .05/
B.O.-TYPE CONVERTERTRANSFORMER,CPL.
Es gelten die Vorschriften und Sicherheitshin-weise gemäß dem Service Manual "Sicherheit",Sach-Nummer 72010-800.00, sowie zusätzlichdie eventuell abweichenden, landesspezifischenVorschriften!
The regulations and safety instructions shall bevalid as provided by the "Safety" Service Manual,part number 72010-800.00, as well as therespective national deviations.( )
Ersatzteilliste / S
pare Parts List
CU
C 7303
5 - 2G
RU
ND
IG S
ervice
ErsatzteillisteSpare Parts List
8 / 96
D Btx * 32700 #
P 37-066/5P 37-071P 37-071
P 37-071 GBSACH-NR. / PART NO.: 9.21595-0202 BESTELL-NR. / ORDER NO.: G.CE 5602 TITANSACH-NR. / PART NO.: 9.21595-0102 BESTELL-NR. / ORDER NO.: G.CE 5302 TITANSACH-NR. / PART NO.: 9.21595-2102 BESTELL-NR. / ORDER NO.: G.CE 5902 TITANSACH-NR. / PART NO.: 9.21595-6302 BESTELL-NR. / ORDER NO.: G.CE 5502 GB TITAN
POS. NR. ABB. SACHNUMMER ANZ.
POS. NO. FIG. PART NUMBER QTY.BEZEICHNUNG DESCRIPTIOND GB
0001.000 29625-723.86 GEHAEUSEVORDERTEIL CABINET FRONT0001.100 29632-082.01 GRUNDIG-EMBLEM GRUNDIG EMBLEM0005.000 19144-039.97 LAUTSPRECHER LOUDSPEAKER0009.000 29636-027.87 GEHAEUSERUECKTEIL REAR PANEL0011.000 29620-017.01 ANTENNE TELESKOP EINSTAB 02/63/21 ANTENNA 02/63/21
29656-002.61 MONTAGE-ZUBEHOER F.BILDROHR MOUNTING ACCESSORIES FPR CRTKEIN E-TEIL NO SPARE PART
0024.000 S 09246-184.71 ENTMAGNETISIERUNGSSPULE DEGAUSSING COIL0025.000 S 8300-020-039 BILDR.A 34 JLL 90X23 JOCH PICT.TUBE A 34 JLL 90X23 JOCH0029.000 29633-375.01 NETZTASTE POWER KEY0030.000 S 8290-991-316 NETZKABEL KPL. 02/01/21 POWER CABLE CPL GWN9.22 02/01/210030.000 S 8290-991-386 NETZKABEL KPL. 63 POWER CABLE CPL GWN9.22 630031.000 29642-062.01 TELEPILOT TP 711 REMOTE CONTROL TP 711
29305-022.14 X BILDROHRPLATTE PICTURE TUBE BOARD
72010-019.40 SERVICE MANUAL SERVICE MANUAL21595-941.02 BEDIENUNGSANLEITUNG 02 OPERATING INSTRUCTIONS 0221595-941.01 BEDIENUNGSANLEITUNG 01/21 OPERATING INSTRUCTIONS 01/2121595-941.03 BEDIENUNGSANLEITUNG 63 OPERATING INSTRUCTIONS 63
29704-002.24 X CHASSIS-FS-MONO 02 CHASSIS TV MONO 02CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
29704-002.21 X CHASSIS-FS-MONO 01/21 CHASSIS TV MONO 01/21CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
29704-002.22 X CHASSIS-FS-MONO 63 CHASSIS TV MONO 63CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LIST
29633-375.01
29625-723.86
29
1
ErsatzteillisteSpare Parts List
6 / 96
D Btx * 32700 #
P 37-731 TEXTP 37-731 TEXT
P 37-731 TEXT GB
POS. NR. ABB. SACHNUMMER ANZ.
POS. NO. FIG. PART NUMBER QUA.BEZEICHNUNG DESCRIPTIOND GB
0001.000 29625-676.01 GEHAEUSEVORDERTEIL 01/64 CABINET FRONT 01/640001.000 29625-676.03 GEHAEUSEVORDERTEIL 83 CABINET FRONT 830001.100 29632-082.01 GRUNDIG-EMBLEM GRUNDIG EMBLEM0001.200 29628-758.01 CHASSISBEFESTIGUNG CHASSIS FASTENING0001.300 29633-885.01 ABDECKUNG COVER0005.000 19144-039.97 LAUTSPRECHER LOUDSPEAKER0005.100 29700-621.01 MONTAGE-FEDER F.LS ASSEMBLY SPRING FOR LS0009.000 29636-023.86 GEHAEUSERUECKTEIL 01/64 REAR PANEL 01/640009.000 29636-023.02 GEHAEUSERUECKTEIL 83 REAR PANEL 830011.000 29620-017.01 ANTENNE TELESKOP EINSTAB ANTENNA, TELESCOPIC 1-ROD
29656-002.61 MONTAGE-ZUBEHOER F.BILDROHR MOUNTING ACCESSORIES FOR CRTKEIN E-TEIL NO SPARE PART
0024.000 S 09246-184.71 ENTMAGNETISIERUNGSSPULE DEGAUSSING COIL0025.000 S 8300-020-039 BILDR.A 34 JLL 90X23 JOCH ORION PICT.TUBE A 34 JLL 90X03 YOKE ORIONWW. S 8300-020-037 BILDR.A 34 EAC 01X06 PHILIPS PICT.TUBE A 34 EAC 01X06 PHILIPS0029.000 29633-375.01 NETZTASTE POWER KEY0030.000 S 8290-991-220 NETZKABEL M.FLACHSTECKER 01/83 MAINS LEAD W.FLAT PLUG + 01/830030.000 S 8290-991-351 NETZKABEL KPL. 64 MAINS LEAD CPL. 640031.000 29642-062.01 TELEPILOT TP 711 REMOTE CONTROL TP 711
29305-022.14 X BILDROHRPLATTE PICTURE TUBE BOARD
72010-019.40 SERVICE MANUAL SERVICE MANUAL21589-941.01 BEDIENUNGSANLEITUNG 01/83 OPERATING INSTRUCTIONS 01/8321589-941.02 BEDIENUNGSANLEITUNG 64 OPERATING INSTRUCTIONS 64
29704-002.05 X CHASSIS-FS-MONO ORION 01/83 CHASSIS TV MONO ORION 01/83CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
WW. 29704-002.06 X CHASSIS-FS-MONO PHILIPS 01/83 CHASSIS TV MONO PHILIPS 01/83CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
29704-002.08 X CHASSIS-FS-MONO ORION 64 CHASSIS TV MONO ORION 64CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
WW. 29704-002.09 X CHASSIS-FS-MONO PHILIPS 64 CHASSIS TV MONO PHILIPS 64CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LISTWW. = WAHLWEISE WW. = OPTIONAL
SACH-NR. / PART NO.: 9.21589-0102 BESTELL-NR. / ORDER NO.: G.CE 4802 TITANSACH-NR. / PART NO.: 9.21589-0183 BESTELL-NR. / ORDER NO.: G.CE 4883 WEISS/WHITESACH-NR. / PART NO.: 9.21589-6402 BESTELL-NR. / ORDER NO.: G.CE 4902 GB TITAN
29625-676.01/03
29632-082.01
1
1.1
CU
C 7303
Spare P
arts List
GR
UN
DIG
Service
5 - 3
ErsatzteillisteSpare Parts List
6 / 96
D Btx * 32700 #
POS. NR. ABB. SACHNUMMER ANZ.
POS. NO. FIG. PART NUMBER QUA.BEZEICHNUNG DESCRIPTIOND GB
P 45-731 TEXT
0001.000 29635-130.02 GEHAEUSEVORDERTEIL KPL. CABINET FRONT CPL.0001.100 29602-605.51 GRUNDIG EMBLEM GRUNDIG EMBLEM0001.200 29628-758.01 2 CHASSISBEFESTIGUNG CHASSIS FASTENING0001.300 29633-886.01 ABDECKUNG DRUCK KPL. COVER PRESSURE CPL.WW. 29633-886.51 ABDECKUNG DRUCK KPL. COVER PRESSURE CPL.0004.000 29633-118.01 GRIFF KPL. HANDLE CPL.0005.000 29700-391.01 2 ACHSE F.GRIFF SPINDLE FOR HANDLE0006.000 29634-364.01 KLEMMSTUECK SHIM0007.000 19146-016.97 LAUTSPRECHER LOUDSPEAKER0008.000 29631-834.02 GEHAEUSERUECKTEIL LACKIER REAR PANEL LACQUERED0008.100 29628-594.80 LAUTSPRECHERAUFNAHME LINKS SPEAKER RECORD LEFT0008.200 29628-595.80 LAUTSPRECHERAUFNAHME RECHTS SPEAKER RECORD RIGHT0011.000 29620-011.51 TELESKOPANTENNE KPL. TELESCOPIC ANTENNA CPL.
29656-002.74 MONT.-ZUBEHOER F.BILDROHR ASSY.ACESSORIES F.PICTUREKEIN E-TEIL NO SPARE PART
0024.000 S 09246-197.71 ENTMAGNETISIERUNGSSPULE DEGAUSSING COIL0025.000 S 8300-020-204 BILDR.A 41 EAM 40X01 PHI PICT.TUBE A 41 EAM 40X01WW. S 8300-020-203 BILDR.A 41 JAR 40X02 (MW) PICT.TUBE A 41 JAR 40X020047.000 29633-881.01 TASTENSATZ KEY SET0048.000 29633-106.01 ZUGENTLASTUNG STRESS RELIEF0049.000 29633-392.01 TASTENKNOPF NETZ KEY BUTTON MAINS0050.000 S 8290-991-220 NETZKABEL M.FLACHSTECKER MAINS LEAD W.FLAT PLUG +0051.000 29642-062.01 TELEPILOT TP 711 REMOTE CONTROL TP 711
29305-022.15 X BILDROHRPLATTE PICTURE TUBE BOARD
72010-019.40 SERVICE MANUAL SERVICE MANUAL21557-941.01 BEDIENUNGSANLEITUNG OPERATING INSTRUCTIONS
29704-002.01 X CHASSIS-FS-MONO CHASSIS TV MONOCUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LISTWW. = WAHLWEISE WW. = OPTIONAL
SACH-NR. / PART NO.:BESTELL-NR. / ORDER NO.:
9.21557-0152G.CE 2652 MET.DKL.
29635-130.02
29602-605.51
1
1.129633-392.0149
ErsatzteillisteSpare Parts List
7 / 96
D Btx * 32700 #
T 51-071T 51-731 TEXT
T 51-732/5 TEXTSACH-NR. / PART NO.: 9.21596-0175 BESTELL-NR. / ORDER NO.: G.CE 5275 COSMOS-SCHWARZ/COSMOS BLACKSACH-NR. / PART NO.: 9.21597-0175 BESTELL-NR. / ORDER NO.: G.CE 5075 COSMOS-SCHWARZ/COSMOS BLACKSACH-NR. / PART NO.: 9.21597-0275 BESTELL-NR. / ORDER NO.: G.CE 5175 COSMOS-SCHWARZ/COSMOS BLACK
POS. NR. ABB. SACHNUMMER ANZ.
POS. NO. FIG. PART NUMBER QUA.BEZEICHNUNG DESCRIPTIOND GB
0001.000 29635-163.01 GEHAEUSEVORDERTEIL KPL CABINET FRONT CPL.0001.100 29632-114.01 EMBLEM GRUNDIG EMBLEM GRUNDIG0007.000 19144-039.97 LAUTSPRECHER LOUDSPEAKER0009.000 29636-024.87 GEHAEUSERUECKTEIL REAR PANEL
29656-003.74 MONTAGE-ZUBEHOER F.BILDROHR MOUNTING ACCESSORIES FOR CRTKEIN E-TEIL NO SPARE PART
0021.000 29607-217.01 2 SPULENKLAMMER UNTEN COIL CLIP LOWERWW. 29607-218.01 2 SPULENKLAMMER UNTEN COIL CLIP LOWER0022.000 29607-284.11 2 SPULENKLAMMER OBEN COIL CLIP UPPERWW. 29607-285.11 2 SPULENKLAMMER OBEN COIL CLIP UPPER0024.000 S 09246-193.31 ENTMAGNETISIERUNGSSPULE DEGAUSSING COILWW. S 09246-193.71 ENTMAGNETISIERUNGSSPULE DEGAUSSING COIL0025.000 S 8300-020-314 BILDR.A48ECR11X60/ A48ECR PICT.TUBE A48ECR11X60/ A40026.000 S 29201-360.01 ANODENKAPPE MIT HOCHSPG.-KABEL C.R.T. SOCKET0028.000 29633-736.01 TASTE NETZ KEY MAINS0030.000 S 8290-991-316 NETZKABEL KPL POWER CABLE CPL GWN9.220031.000 29642-062.01 TELEPILOT TP 711 REMOTE CONTROL TP711
29305-022.16 X BILDROHRPLATTE PICTURE TUBE BOARD
72010-019.40 SERVICE MANUAL SERVICE MANUAL21596-941.01 BEDIENUNGSANLEITUNG T 51-071 OPERATING INSTRUCTIONS T 51-07121597-941.01 BEDIENUNGSANLEITUNG T 51-731 TEXT OPERATING INSTRUCTIONS T 51-731 TEXT21596-941.02 BEDIENUNGSANLEITUNG T 51-732/5 TEXT OPERATING INSTRUCTIONS T 51-732/5 TEXT
29704-002.12 X CHASSIS-FS-MONO T 51-071 CHASSIS TV MONO T 51-071CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
29704-002.04 X CHASSIS-FS-MONO T 51-731 TEXT CHASSIS TV MONO T 51-731 TEXTCUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
29704-002.14 X CHASSIS-FS-MONO T 51-732/5 TEXT CHASSIS TV MONO T 51-732/5 TEXTCUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LISTWW. = WAHLWEISE WW. = OPTIONAL
29635-163.01
29632-114.01
1
1.1
29633-736.0128
ErsatzteillisteSpare Parts List
2 / 96 T 51-720 TEXTT 51-720 TEXT GB
D Btx * 32700 #
SACH-NR. / PART NO.: 9.21538-0175 BESTELL-NR. / ORDER NO.: G.CD 9675 COSMOS-SCHWARZ/COSMOS BLACKSACH-NR. / PART NO.: 9.21538-6475 BESTELL-NR. / ORDER NO.: G.CD 9775GB COSMOS-SCHWARZ/COSMOS BLACK
POS. NR. ABB. SACHNUMMER ANZ.
POS. NO. FIG. PART NUMBER QUA.BEZEICHNUNG DESCRIPTIOND GB
0001.000 29635-159.02 GEHAEUSEVORDERTEIL KPL. CABINET FRONT CPL.0001.100 29602-603.51 GRUNDIG-EMBLEM GRUNDIG EMBLEM0005.000 29628-785.01 2 CHASSISBEFESTIGUNG CHASSIS FIXTURE0006.000 19116-008.97 LAUTSPRECHER SPEAKER0010.000 29631-936.87 GEHAEUSERUECKTEIL REAR PANEL
29656-003.74 MONTAGE-ZUBEHOER F.BILDROHR MOUNTING ACCESSORIES FOR CRTKEIN E-TEIL NO SPARE PART
0021.000 29607-217.01 2 SPULENKLAMMER UNTEN COIL CLIP LOWERWW. 29607-218.01 2 SPULENKLAMMER UNTEN COIL CLIP LOWER0022.000 29607-284.11 2 SPULENKLAMMER OBEN COIL CLIP UPPERWW. 29607-285.11 2 SPULENKLAMMER OBEN COIL CLIP UPPER0024.000 S 09246-193.31 ENTMAGNETISIERUNGSSPULE DEGAUSSING COILWW. S 09246-193.71 ENTMAGNETISIERUNGSSPULE DEGAUSSING COIL0025.000 S 8300-020-314 BILDR.A48ECR11X60/ A48ECR PICT.TUBE A48ECR11X60/ A40026.000 S 29201-360.01 ANODENKAPPE MIT HOCHSPG.-KABEL C.R.T. SOCKET0034.000 29633-682.01 TASTENKNOPF NETZ KEY BUTTON MAINS0035.000 S 8290-991-220 NETZKABEL KPL. 01 MAINS CABLE CPL. 010035.000 S 8290-991-351 NETZKABEL KPL. 64 MAINS CABLE CPL. 640036.000 29642-062.01 TELEPILOT TP 711 REMOTE CONTROL TP 711
0041.000 29628-893.01 TV-STAND LARGE GRUNDIG 64 TV-STAND LARGE GRUNDIG 64KEIN E-TEIL NO SPARE PART
29305-022.16 X BILDROHRPLATTE PICTURE TUBE BOARD
72010-019.40 SERVICE MANUAL SERVICE MANUAL21538-941.02 BEDIENUNGSANLEITUNG 01 OPERATING INSTRUCTIONS 0121538-941.01 BEDIENUNGSANLEITUNG 64 OPERATING INSTRUCTIONS 64
29704-002.04 X CHASSIS-FS-MONO 01 CHASSIS TV MONO 01CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
29704-002.03 X CHASSIS-FS-MONO 64 CHASSIS TV MONO 64CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LISTWW. = WAHLWEISE WW. = OPTIONAL
GRUNDIG
29635-159.02
29602-603.51
1
1.1
ErsatzteillisteSpare Parts List
8 / 96
D Btx * 32700 #
T 55-731 TEXTT 55-731 TEXT
T 55-731 FT GBT 55-732/5 TEXTT 55-733/5 TEXT
SACH-NR. / PART NO.: 9.21598-0175 BESTELL-NR. / ORDER NO.: G.CE 6775 COSMOS-SCHWARZ/COSMOS BLACKSACH-NR. / PART NO.: 9.21598-0183 BESTELL-NR. / ORDER NO.: G.CE 6783 WEISS/WHITESACH-NR. / PART NO.: 9.21598-6475 BESTELL-NR. / ORDER NO.: G.CE 7075 GB COSMOS-SCHWARZ/COSMOS BLACKSACH-NR. / PART NO.: 9.21598-0275 BESTELL-NR. / ORDER NO.: G.CE 6875 COSMOS-SCHWARZ/COSMOS BLACKSACH-NR. / PART NO.: 9.21598-7575 BESTELL-NR. / ORDER NO.: G.CE 6975 COSMOS-SCHWARZ/COSMOS BLACK
POS. NR. ABB. SACHNUMMER ANZ.
POS. NO. FIG. PART NUMBER QTY.BEZEICHNUNG DESCRIPTIOND GB
0001.000 29635-159.03 GEHAEUSEVORDERTEIL KPL. 75/64.75/75.75 CABINET FRONT CPL. 75/64.75/75.750001.000 29635-159.04 GEHAEUSEVORDERTEIL KPL. 83 CABINET FRONT CPL. 830001.100 29602-603.51 GRUNDIG-EMBLEM GRUNDIG EMBLEM0006.000 19116-008.97 LAUTSPRECHER SPEAKER0007.000 29628-785.01 2 CHASSISBEFESTIGUNG CHASSIS FIXTURE0010.000 29631-936.87 GEHAEUSERUECKTEIL 75/64.75/75.75 REAR PANEL 75/64.75/75.750010.000 29631-936.05 GEHAEUSERUECKTEIL OFB 83 REAR PANEL 83
29656-003.74 MONTAGE-ZUBEHOER F.BILDROHR MOUNTING ACCESSORIES FOR CRTKEIN E-TEIL NO SPARE PART
0021.000 29607-217.01 2 SPULENKLAMMER UNTEN COIL CLIP LOWERWW. 29607-218.01 2 SPULENKLAMMER UNTEN COIL CLIP LOWER0022.000 29607-284.11 2 SPULENKLAMMER OBEN COIL CLIP UPPERWW. 29607-285.11 2 SPULENKLAMMER OBEN COIL CLIP UPPER0024.000 S 09246-193.31 ENTMAGNETISIERUNGSSPULE DEGAUSSING COILWW. S 09246-193.71 ENTMAGNETISIERUNGSSPULE DEGAUSSING COIL0025.000 S 8300-020-635 BILDR.A51EAL135X01 PHI PICT.TUBE A51EAL135X010026.000 S 29201-360.01 ANODENKAPPE MIT HOCHSPG.-KABEL C.R.T. SOCKET0039.000 29633-682.01 TASTENKNOPF 75 KEY BUTTON 750040.000 S 8290-991-351 NETZKABEL KPL. 75 POWER CABLE CPL. 750040.000 S 8290-991-220 NETZKABEL M. FLACHST. 83/75/02.75/75.75 POWER CABLE W.FLAT PLUG + 83/75/02.75/75.750040.000 S 8290-991-386 NETZKABEL KPL. 64.75 POWER CABLE CPL. 64.750043.000 29642-062.01 TELEPILOT TP 711 REMOTE CONTROL TP 7110043.000 29642-063.01 TELEPILOT TP 712.64 REMOTE CONTROL TP 712.64
29305-022.16 X BILDROHRPLATTE PICTURE TUBE BOARD
72010-019.40 SERVICE MANUAL SERVICE MANUAL21598-941.01 BEDIENUNGSANLEITUNG 01.75/83 OPERATING INSTRUCTIONS 01.75/8321598-941.05 BEDIENUNGSANLEITUNG 64.75 OPERATING INSTRUCTIONS 64.7521598-941.02 BEDIENUNGSANLEITUNG 02.75 OPERATING INSTRUCTIONS 02.7521598-941.03 BEDIENUNGSANLEITUNG 75.75 OPERATING INSTRUCTIONS 75.75
29628-893.01 TV-STAND LARGE GRUNDIG 64.75 TV-STAND LARGE GRUNDIG 64.75KEIN E-TEIL NO SPARE PART
29704-002.07 X CHASSIS-FS-MONO 01.75/83 CHASSIS TV MONO 01.75/83CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
29704-002.18 X CHASSIS-FS-MONO 64.75 CHASSIS TV MONO 64.75CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
29704-002.16 X CHASSIS-FS-MONO 02.75 CHASSIS TV MONO 02.75CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
29704-002.17 X CHASSIS-FS-MONO 75.75 CHASSIS TV MONO 75.75CUC 7303 CUC 7303KEIN E-TEIL NO SPARE PART
X = SIEHE GESONDERTE E-LISTE X = SEE SEPARATE PARTS LISTWW. = WAHLWEISE WW. = OPTIONAL
Ersatzteilliste / S
pare Parts List
CU
C 7303
Änderungen vorbehalten
Printed in G
ermany
Service M
anual Sach-N
r. / Part N
o. 72010-019.40S
ubject to alterationV
K 221 1196
8002/8012, 8003/8013