NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certifi ed technician. Logos and trademarks used here in are the properties of their respective owners.

WARNINGPressing the printer icon or “quick printing” this document will print

all of the guides in this compilation.

Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.

Print only the pages for your vehicle using the advanced options in the Print menu.

Install your Maestro RR according to the guide for your vehicle.

HOW TO USE THIS INSTALL GUIDE1

2

3

SELECT VEHICLE PRINT PAGES NEEDED

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA 4 RUNNER

WITh JBL 2014-2017Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota 4 RunneR with JBl 2014-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota 4 RunneR with JBl 2014-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the male WHITE 2 pin connector of your TO2

T-harness into the OBDII harness.

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

1

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota 4 RunneR with JBl 2014-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

1

H

H

BACKUP CAMBACKUP CAM

MAINHARNESS

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

STEP 5

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

CONNECT IF EQUIPPED

CONNECT TOAFTERMARKET RADIO

STEP 6

MAESTRO RR MODULE

DATACABLE

OBDII CONNECTORSTEP 4

WIRING DIAGRAM with an Amplifier

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

STEP 1WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECTIONSNOTREQUIREDWITH AMP

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota 4 RunneR with JBl 2014-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA 4 RUNNERWIThOUT JBL 2014-2017

Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota 4 RunneR without JBl 2014-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota 4 RunneR without JBl 2014-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the front speaker wire junction connectors.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the male WHITE 2 pin connector of your TO2

T-harness into the OBDII harness.

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

2

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota 4 RunneR without JBl 2014-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

2

H

H

BACKUP CAMBACKUP CAM

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 5

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 6

MAESTRO RR MODULE

DATACABLE

OBDII CONNECTORSTEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota 4 RunneR without JBl 2014-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA AvALONWITh JBL 2015-2016

Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota avalon with JBl 2015-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota avalon with JBl 2015-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

3

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota avalon with JBl 2015-2016

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

3

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

MAINHARNESS

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

WIRING DIAGRAM with an Amplifier

CONNECTION NOT REQUIRED

CONNECT IF EQUIPPED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECTIONSNOTREQUIREDWITH AMP

STEP 1

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota avalon with JBl 2015-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA AvALON

WIThOUT JBL 2015-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota avalon without JBl 2015-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota avalon without JBl 2015-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the front speaker wire junction connectors.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

4

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota avalon without JBl 2015-2016

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

4

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

CONNECTION NOT REQUIRED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota avalon without JBl 2015-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA CAMRy

WITh FACTORy 6.1" SCREEN 2012-2014Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy 6.1" scReen 2012-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy 6.1" scReen 2012-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the front speaker wire junction connectors.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy 6.1" scReen 2012-2014

Automotive Data Solutions Inc. © 2017 4

23 1456789101213 11141516

AUX INAUX IN

A

G

F

A FG

5

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

CONNECTION NOT REQUIRED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

YELLOW WHITERED

BLACK

BLACK

BLUE/YELLOWBLACK

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPEDCUT REVERSECAMERACONNECTOR FROMTO2 T-HARNESSAND CONNECTWIRES AS SHOWN.

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy 6.1" scReen 2012-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA CAMRy

WITh FACTORy 6.1" SCREEN AND JBL 2012-2014

Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy 6.1" scReen and JBl 2012-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy 6.1" scReen and JBl 2012-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

6

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy 6.1" scReen and JBl 2012-2014

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

23 1456789101213 11141516

A

G

F

A FG

6

H

H

BACKUP CAMBACKUP CAM

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

RCA CABLES

STEP 1 STEP 4WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

WIRING DIAGRAM with an Amplifier

CONNECTIONSNOTREQUIREDWITH AMP

NOT CONNECTED

CONNECTION NOT REQUIRED

YELLOW WHITERED

BLACK

BLACK

BLUE/YELLOWBLACK

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

WIRES FROMVEHICLE

STEP 5

MAESTRO RR MODULE

DATACABLECUT REVERSE

CAMERACONNECTOR FROMTO2 T-HARNESSAND CONNECTWIRES AS SHOWN.

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy 6.1" scReen and JBl 2012-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA CAMRy

WITh FACTORy SCREEN AND hDD AND JBL 2012-2014

Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy scReen and hdd and JBl 2012-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy scReen and hdd and JBl 2012-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

6

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy scReen and hdd and JBl 2012-2014

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

23 1456789101213 11141516

A

G

F

A FG

6

H

H

BACKUP CAMBACKUP CAM

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

RCA CABLES

STEP 1 STEP 4WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

WIRING DIAGRAM with an Amplifier

CONNECTIONSNOTREQUIREDWITH AMP

NOT CONNECTED

CONNECTION NOT REQUIRED

YELLOW WHITERED

BLACK

BLACK

BLUE/YELLOWBLACK

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

WIRES FROMVEHICLE

STEP 5

MAESTRO RR MODULE

DATACABLECUT REVERSE

CAMERACONNECTOR FROMTO2 T-HARNESSAND CONNECTWIRES AS SHOWN.

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with factoRy scReen and hdd and JBl 2012-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA CAMRyWITh JBL 2015-2017

Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with JBl 2015-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with JBl 2015-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

3

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with JBl 2015-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

3

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

MAINHARNESS

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

WIRING DIAGRAM with an Amplifier

CONNECTION NOT REQUIRED

CONNECT IF EQUIPPED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECTIONSNOTREQUIREDWITH AMP

STEP 1

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy with JBl 2015-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA CAMRy

WIThOUT JBL 2015-2017Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy without JBl 2015-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy without JBl 2015-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the front speaker wire junction connectors.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

4

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy without JBl 2015-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

4

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

CONNECTION NOT REQUIRED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota camRy without JBl 2015-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA COROLLA

WITh FACTORy 6.1" SCREEN 2014-2017Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota coRolla with factoRy 6.1" scReen 2014-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota coRolla with factoRy 6.1" scReen 2014-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the front speaker wire junction connectors.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

4

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota coRolla with factoRy 6.1" scReen 2014-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

4

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

CONNECTION NOT REQUIRED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota coRolla with factoRy 6.1" scReen 2014-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA hIGhLANDER

WITh JBL 2014-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota highlandeR with JBl 2014-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota highlandeR with JBl 2014-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

3

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota highlandeR with JBl 2014-2016

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

3

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

MAINHARNESS

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

WIRING DIAGRAM with an Amplifier

CONNECTION NOT REQUIRED

CONNECT IF EQUIPPED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECTIONSNOTREQUIREDWITH AMP

STEP 1

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota highlandeR with JBl 2014-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA hIGhLANDER

WIThOUT JBL 2014-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota highlandeR without JBl 2014-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota highlandeR without JBl 2014-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the front speaker wire junction connectors.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

4

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota highlandeR without JBl 2014-2016

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

4

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

CONNECTION NOT REQUIRED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota highlandeR without JBl 2014-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA RAv 4

WITh FACTORy 6.1" SCREEN 2013-2017Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota Rav 4 with factoRy 6.1" scReen 2013-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota Rav 4 with factoRy 6.1" scReen 2013-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the front speaker wire junction connectors.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

4

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota Rav 4 with factoRy 6.1" scReen 2013-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

4

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

CONNECTION NOT REQUIRED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota Rav 4 with factoRy 6.1" scReen 2013-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA RAv 4

WITh FACTORy 6.1" SCREEN AND JBL 2013-2017

Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota Rav 4 with factoRy 6.1" scReen and JBl 2013-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota Rav 4 with factoRy 6.1" scReen and JBl 2013-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

3

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota Rav 4 with factoRy 6.1" scReen and JBl 2013-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

3

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

MAINHARNESS

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

WIRING DIAGRAM with an Amplifier

CONNECTION NOT REQUIRED

CONNECT IF EQUIPPED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECTIONSNOTREQUIREDWITH AMP

STEP 1

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota Rav 4 with factoRy 6.1" scReen and JBl 2013-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA SIENNAWITh JBL 2015-2017

Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota sienna with JBl 2015-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota sienna with JBl 2015-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

Note: The reverse camera cannot be retained in this vehicle.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the male WHITE 2 pin connector of your TO2

T-harness into the OBDII harness.

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

7

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota sienna with JBl 2015-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

7

H

H

BACKUP CAMBACKUP CAM

REVERSE CAMERA HARNESSSTEP 2CONNECT IF EQUIPPED

MAINHARNESS

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

TO2 T-HARNESS

STEP 3

STEP 5

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

CONNECTION NOT REQUIREDREVERSE CAMERA CANNOTBE RETAINED

CONNECT TOAFTERMARKET RADIO

STEP 6

MAESTRO RR MODULE

DATACABLE

OBDII CONNECTORSTEP 4

WIRING DIAGRAM with an Amplifier

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

STEP 1WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECTIONSNOTREQUIREDWITH AMP

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota sienna with JBl 2015-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA SIENNA

WIThOUT JBL 2015-2017Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota sienna without JBl 2015-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota sienna without JBl 2015-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the front speaker wire junction connectors.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the male WHITE 2 pin connector of your TO2

T-harness into the OBDII harness.

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

2

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota sienna without JBl 2015-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

2

H

H

BACKUP CAMBACKUP CAM

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 5

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 6

MAESTRO RR MODULE

DATACABLE

OBDII CONNECTORSTEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota sienna without JBl 2015-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA TACOMAWITh JBL 2016-2017

Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tacoma with JBl 2016-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tacoma with JBl 2016-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

3

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tacoma with JBl 2016-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

3

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

MAINHARNESS

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

WIRING DIAGRAM with an Amplifier

CONNECTION NOT REQUIRED

CONNECT IF EQUIPPED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECTIONSNOTREQUIREDWITH AMP

STEP 1

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tacoma with JBl 2016-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA TACOMA

WIThOUT JBL 2016-2017Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tacoma without JBl 2016-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tacoma without JBl 2016-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the front speaker wire junction connectors.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 5• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

4

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tacoma without JBl 2016-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

4

H

H

BACKUP CAMBACKUP CAM

NOT CONNECTED

CONNECTION NOT REQUIRED

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 4

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 5

MAESTRO RR MODULE

DATACABLE

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tacoma without JBl 2016-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA TUNDRAWITh JBL 2014-2017

Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tundRa with JBl 2014-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tundRa with JBl 2014-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the male WHITE 2 pin connector of your TO2

T-harness into the OBDII harness.

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

1

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tundRa with JBl 2014-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

1

H

H

BACKUP CAMBACKUP CAM

MAINHARNESS

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

STEP 5

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

CONNECT IF EQUIPPED

CONNECT TOAFTERMARKET RADIO

STEP 6

MAESTRO RR MODULE

DATACABLE

OBDII CONNECTORSTEP 4

WIRING DIAGRAM with an Amplifier

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

STEP 1WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECTIONSNOTREQUIREDWITH AMP

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tundRa with JBl 2014-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA TUNDRA

WIThOUT JBL 2014-2017Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tundRa without JBl 2014-2017

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tundRa without JBl 2014-2017

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Cut and remove the front speaker wire junction connectors.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera, connect the TO2 T-harness to the backup camera harness.

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the male WHITE 2 pin connector of your TO2

T-harness into the OBDII harness.

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

2

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tundRa without JBl 2014-2017

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

2

H

H

BACKUP CAMBACKUP CAM

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)PURPLE/WHITE - REVERSE LIGHT (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 5

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 6

MAESTRO RR MODULE

DATACABLE

OBDII CONNECTORSTEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPED

YELLOW/GREEN (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota tundRa without JBl 2014-2017

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA vENzA

WITh JBL 2015-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza with JBl 2015-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza with JBl 2015-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the male WHITE 2 pin connector of your TO2

T-harness into the OBDII harness.

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

8

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza with JBl 2015-2016

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

9

H

H

BACKUP CAMBACKUP CAM

MAINHARNESS

RCA CABLES

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

STEP 5

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

CONNECT IF EQUIPPED

CONNECT TOAFTERMARKET RADIO

STEP 6

MAESTRO RR MODULE

DATACABLE

OBDII CONNECTORSTEP 4

WIRING DIAGRAM with an Amplifier

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

STEP 1WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECTIONSNOTREQUIREDWITH AMP

YELLOW/GREEN - REVERSE LIGHT (+)YELLOW/GREEN - REVERSE LIGHT (+)

PURPLE/WHITEPURPLE/WHITE (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza with JBl 2015-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA vENzA

WITh JBL AND NAv 2013-2014Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza with JBl and nav 2013-2014

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza with JBl and nav 2013-2014

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the male WHITE 2 pin connector of your TO2

T-harness into the OBDII harness.

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

8

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza with JBl and nav 2013-2014

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

23 1456789101213 11141516

A FG

A

G

F

8

H

H

BACKUP CAMBACKUP CAM

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

RCA CABLES

STEP 1 STEP 5WHITEWHITE/BLACKGRAYGRAY/BLACK

LF RCA INPUT

RF RCA INPUT

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

WIRING DIAGRAM with an Amplifier

CONNECTIONSNOTREQUIREDWITH AMP

YELLOW REDWHITE

BLACK

BLACK

BLUE/YELLOWBLACK

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 2

STEP 3

WIRES FROMVEHICLE

STEP 6

MAESTRO RR MODULE

DATACABLE

CUT REVERSECAMERACONNECTOR FROMTO2 T-HARNESSAND CONNECTWIRES AS SHOWN.

CONNECT IF EQUIPPED

OBDII CONNECTORSTEP 4

YELLOW/GREEN - REVERSE LIGHT (+)YELLOW/GREEN - REVERSE LIGHT (+)

PURPLE/WHITEPURPLE/WHITE (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza with JBl and nav 2013-2014

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink

OPTIONAL ACCESSORIES

PROGRAMMED FIRMWAREADS-RR(SR)-TOY02-DS

PRODUCTS REQUIREDiDatalink Maestro RR Radio Replacement InterfaceiDatalink Maestro TO2 Installation Harness

INSTALL GUIDETOyOTA vENzA

WIThOUT JBL 2015-2016Retains factoRy amplifieR, steeRing wheel contRols, and moRe!

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza without JBl 2015-2016

Automotive Data Solutions Inc. © 2017 2

WELCOME

NEED hELP?

Congratulations on the purchase of your iDatalink Maestro RR Radio replacement solution. You are now a few simple steps away from enjoying your new car radio with enhanced features. Before starting your installation, please ensure that your iDatalink Maestro module is programmed with the correct fi rmware and that you carefully review the Installation Diagram and Vehicle Wire Refer-ence Chart.

Please note that Maestro RR will only retain functionalities that were originally available in the vehicle.

1 866 427-2999

support@idatalink.com

maestro.idatalink.com/supportwww.12voltdata.com/forum

DURING INSTALLATION

Installation Instructions 3

Wiring Diagram 4

Radio Wire Reference Chart 5

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza without JBl 2015-2016

Automotive Data Solutions Inc. © 2017 3

INSTALLATION INSTRUCTIONS STEP 1

• Unbox the aftermarket radio and locate its main harness.

• Connect the wires shown on the next page from aftermarket radio main harness to the TO2 T-harness and match the wire functions.

• Remove the factory radio.

STEP 2

• If the vehicle is equipped with an OEM backup camera: Cut the reverse camera plug of the TO2 T-harness and connect the wires as indicated in the wiring diagram next page (BROWN/RED and BROWN/YELLOW wires are not used).

STEP 3

• Connect the factory harness to the TO2 T-harness.

STEP 4• Plug the male WHITE 2 pin connector of your TO2

T-harness into the OBDII harness.

• Plug the OBDII connector into the OBDII of the vehicle.

STEP 5• Plug the aftermarket radio harnesses into the aftermarket

radio.

• Connect the backup camera RCA cable into the aftermarket radio (if equipped).

• Connect the auxiliary RCA cables into the aftermarket radio (if equipped).

• Plug the Data cable to the data port of the aftermarket radio.

STEP 6• Connect all the harnesses to the Maestro RR module then

test your installation.

TROUBLESHOOTING TIPS:

• To reset the module back its factory settings, turn the key to the OFF position then disconnect all connectors from the module. Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will fl ash RED rapidly (this may take up to 10 seconds). Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds.

• For technical assistance call 1-866-427-2999 or e-mail “support@idatalink.com”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”

8

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza without JBl 2015-2016

Automotive Data Solutions Inc. © 2017 4

AUX INAUX IN

A

G

F

A FG

2

H

H

BACKUP CAMBACKUP CAM

YELLOW - 12V (+)

BLACK - GROUNDRED - ACCESSORY (+)

YELLOW/BLACK - FOOT BRAKE

ORANGE - ILLUMINATION (+)

PINK - VEHICLE SPEEDLTGREEN - E-BRAKE (-)

BLUE/WHITE - AMP. TURN ON (+)

MAINHARNESS

RCA CABLES

FACTORY RADIO HARNESS

REVERSE CAMERA HARNESS

TO2 T-HARNESS

STEP 1

STEP 2

STEP 3

STEP 5

WIRES FROMVEHICLE

CONNECT YELLOW RCA AUX IN IF VEHICLE IS EQUIPPED WITHAUXILIARY VIDEO

SEE AFTERMARKETRADIO GUIDEFOR RADIO WIRECOLORS

GREEN - LR SPEAKER (+)GREEN/BLACK - LR SPEAKER (-)

PURPLE/BLACK - RR SPEAKER (-)PURPLE - RR SPEAKER (+)

CONNECT TOAFTERMARKET RADIO

STEP 6

MAESTRO RR MODULE

DATACABLE

OBDII CONNECTORSTEP 4

CUT AND REMOVE THE SPEAKER WIRE JUNCTION CONNECTORS

WHITE - LF SPEAKER (+)WHITE/BLACK - LF SPEAKER (-)GRAY - RF SPEAKER (+)GRAY/BLACK - RF SPEAKER (-)

WIRING DIAGRAM without an Amplifier

CONNECT IF EQUIPPED

YELLOW/GREEN - REVERSE LIGHT (+)YELLOW/GREEN - REVERSE LIGHT (+)

PURPLE/WHITEPURPLE/WHITE (NOT CONNECTED)

ADS-RR(SR)-TOY02-DS maestro.idatalink.com

toyota venza without JBl 2015-2016

Automotive Data Solutions Inc. © 2017 5

RADIO WIRE REFERENCE CHART

WireDescription Polarity Wire Color on Maestro

T-Harness Wire Color on Alpine cable Wire Color on Kenwood cable Wire Color on Pioneer cable

Illumination (+) Orange N/A Orange/White Orange/White

Reverse Light (+) Purple/White or Yellow/Green(see Wiring diagram) Orange/White Purple/White Purple/White

E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green

Foot Brake (+) Yellow/Black Yellow/Black N/A N/A

VSS (vehicle speed sensor) (DATA) Pink Green/White N/A Pink