I tc

transcript

ZTE University univ.zte.com.cn univ.zte.com.cnThe information contained in the file is solely property of ZTE corporation. Any kind of disclosing without permission is prohibited.

Welcome to ZTE University

The information contained in the file is solely property of ZTE corporation. Any kind of disclosing without permission is prohibited. ZTE University univ.zte.com.cn univ.zte.com.cn

iTC Overview

iTC Service Networking

Purposes of applying iTC in the network are: Save Transmission resources Share Transcoder resources among iBSCs Improve the utilization rate of TCU

resources Flex Ater/A interfaces provide disaster

recovery.

Interface Indices

A-interface uses the following media:

1. E1-link - 256-1 / 768-2 / 1024-3 / 1536-4

2. STM1-link – 4-1 /12-2 / 16-3 /24

A-ter interface uses the following media:

1. E1-link – 64 -1 / 192-2 / 256-3 / 384 - 4

2. STM1-link – 1-1 / 3-2 / 4 - 3 / 6-4

ZXG10 iTC System Composition

Hardware Structure of ZXG10 iTC

iTC Shelves Description

iTC Shelf Configurations

Control Shelf is configured in the second shelf of the third cabinet if needed. For one or two Cabinet iTC configurations, control shelf’s boards are distributed in other shelves. Packet Switching Shelf and Circuit Switching Shelf should be configured in the fourth and first shelves respectively.

Connection Description

Clock Distribution of Combined Cabinet

Ethernet Connections of Combined Cabinets

User Plane connections of combined cabinet (GLI)

User Plane connections of combined cabinet (TFI)

iTC External Connections

Structure of Resource Shelf

Structure of Circuit Switching Shelf

Structure of Packet Switching Shelf

Structure of Control Shelf

External Interfaces

Clock Distribution

User Plane Signaling flow

Control Plane Signaling flow

Service Networking

A-ter Interface Networking A-interface Networking

Maintenance System Networking

Configuration principles

System configuration principles for Ater interface TDM access modes are:

iTC supports 1 to 4 Rack configurations One SPB supports 128 no.7 Signaling. There are 2

SPB boards that can process 256 no.7 signaling. Resource shelf = AIU + TCU + Ater

2 Resource shelves = one PRCBU

System capacity expansion is very easy, only needs to stack PRCBU

Contd..

For Full rate Ater GUP can process 3360 voice channels.

For Half rate, Ater GUP can process 4200 voice channels.

Normally average value supported by Ater Gup is 3600 voice channels.

TC GUP supports 840 Traffic channels (14 DSP x 60)

Multiplexing ratio for cabling E1 or STM-1 Interface at Ater-interface is 1:4 for FR; 1:8 for HR.

iTC System Configuration (Ater Interface TDM)

Example to calculate no. of boards required in One PRCBU

1 PRCBU = 2 shelvesTo support 1024 Trx,At A-interface, 256 E1 required ie 8 DTBAt A-ter, 64 E1 required ie. 2 DTBTotal= 10 DTB.One TC GUP supports, 840 TCsFor 1024 TRX, 8192 TCs ie 10 GUPs At Ater- 8192/4 =2048 TCs=3 GUPsTotal =13 GUPs.

Detailed System Configuration.

iTC can have a maximum of 4 Racks in various configurations according to different situations such as Ater uses E1 or STM-1 and A-interface uses E1 or STM-1.

Integrated T-Network and Integrated IP switch are mutually inclusive in iTC configuration ie either use both or none

Detailed System Configuration

Dual Shelf iTC Stack Configuration

Single Rack Configuration (A/Ater uses E1)

Dual Rack configuration( Ater/A-interface uses E1 )

I tc

Technology