Post on 30-Mar-2020
transcript
Inline SliderSpecification File
Contents
Specification Overview
Security
Inline Slider Make-Up
Performance and Limitations
Master Configurations
Technical Drawings
Installation Guide
Notes
04
06
07
08
09
14
34
66
3
4
Specification OverviewThermally Broken Aluminium Inline Slider
Profile specificationFrame Depth 2 options: 116mm (double track) and 182mm (triple track)
Sightline 20mm interlockers, 159mm central locking stiles (if used)
Track Height 44mm (double and triple track)
Maximum Individual Panel Size 2200mm wide x 3000mm tall* *individual panels cannot exceed 6sqm
*the height of an individual panel cannot exceed 3 times its width
Minimum Individual Panel Size 550mm wide x 1600mm tall
Internal view of
the Origin Inline Slider
External view of
the Origin Inline Slider
5
Inlin
e Sl
ider
FeaturesOptions and extras
Glazing options
Up to a 20-year guarantee including gaskets and seals*
Up to a 10-year guarantee on glass*
Ultra-slim 20mm sightlines
Available in any RAL finish
Concealed running gear and track
Minimum of 6 points of locking (internal lever and cylinder only)
Weather testing BS6375 part 1 certified
Can accommodate large panel sizes
Up to 6 paneled configurations - these can be all sliding or a combination of fixed and sliding
All RAL colours available
Lever options: 7015M, 7016M, 9005M, 9910G
Drip bar available
Structurally bonded system (Fixed panels will require bonding on site by the installer)
The premium low-e toughened glass used is a dependable double glazed unit. Constructed of two toughened sheets - a minimum of 6mm on both the inward and outward facing panes, making it highly durable as well as thermally efficient.
*Guarantee based on location of where the doors will be installed. Full terms and conditions can be found on the Origin website - origin-global.com/terms-and-conditions.
The Origin Inline Slider is available in the following finishes...
Anthracite Grey (7016M) Jet Black (9005M)
ANYRAL
COLOUR6
WEEKLEAD TIME
Origin’s special RAL colours are available on an 8-week lead time
For the full range, visit origin-global.com
Dual colour and woodgrain options are not available.
6
Security
Each door is equipped with an ultra-secure multi-point locking system, which features a minimum of six points of locking. Depending on the size of the door, this may increase.
TS007 1 star cylinder
Internal cylinder only
Origin’s Multi-Point Lock
Cylinder
Lever
Every inline slider is fitted with a flush faced lever handle
Available in four attractive colours: 9910G, 7015M,
7016M, 9005M
7
Inlin
e Sl
ider
Inline Slider Make-Up
InlineHandle
JambSliding to Sliding
Interlocker
Top Track
Frame
Bottom Track
Make-up is dependent on the configuration chosen.
8
Standard Glass SKN176 / 18mm Thermobar / Clear / Toughened
Laminate 6 and 6.8 Glass 6mm Climbaguard Low E / 18mm Thermobar / Clear
Laminate 8 and 8.8 Glass 8mm Climbaguard Low E / 12mm Thermobar / Clear
Solar Reflective Sunguard Silver 20
Performance and Limitations
u-Value 1.4W/m²K
Origin Thermal Ratings
Weather Rating
Glazing Specifications
Air Permeability Class 4
Water Tightness Class 7A
Resistance to Wind Load Class A3
Exposure Category 1200
Size Limitations
Maximum individual panel size:
2200mm wide x 3000mm tall*
*individual panels cannot exceed 6sqm.
The height of an individual panel cannot
exceed 3 times its width
Minimum individual panel size:
550mm wide x 1600mm tall
PAS 24 Certified (Document Q Compliant)*
BS6375 Parts 1, 2 and 3 Certified
New Build
and Extensions 2.0 W/ (m2K)
Replacements 1.8 W/ (m2K)
Energy Rating E or better
All doors must conform to
these requirements
Building Regulation RequirementsPerformance Testing
AccreditationISO 9001
*Only available on 1+0 configuration with a triple track
9
Inlin
e Sl
ider
2 panel
3 panel
Master Configurations
4 panel
6 panel
10
Master Configuration: 2 panel (2+0)
Key features Both panels can be
sliding, or one can be fixed with one sliding
Traditional patio door style
See Configuration Key for section detail
2+0
See page 09 for configurations
Master Configurations
16
15 1513
14
2+0 ConfigurationSliding Left
SCALE A3 @ 1:10
LEAD DOOR
INTERNAL
EXTERNAL
11
Inlin
e Sl
ider
Configuration Key
See page 26 See page 27
13 - Sliding interlocker to sliding interlocker detail
14 - Sliding panel to double frame (bottom track) detail
See page 29
16 - Sliding panel to double frame (top track) detail
15 - Sliding panel to double frame (jamb) detail
SLIDER DETAIL DRAWINGSliding Interlocker to Sliding Interlocker Detail
226
20
INTERLOCKER
INTERLOCKER BEAD
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000712
2
Sliding Interlocker toSliding InterlockerDetail
1 OF 1
± --
± --
SLIDER DETAIL DRAWINGSliding Panel to Double Frame (Jamb) Detail
105
116
44
FRAME COVER
LOCKSTILE
BRUSH GASKET
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000708
2
Sliding Panel to Double Frame (Jamb)Detail
1 OF 1
± --
± --
SLIDER DETAIL DRAWINGSliding Panel to Double Frame (Bottom Track) Detail
44
BOTTOM SASH
RUNNING GEAR
116
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000716
2
Sliding Panel to DoubleFrame (Bottom Track)Detail
1 OF 1
± --
± --
SLIDER DETAIL DRAWINGSliding Panel to Double Frame (Top Track) Detail
TOP SASH
ANTI-LIFT PACKER
44
116
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000717
2
Sliding Panel to DoubleFrame (Top Track)Detail
1 OF 1
± --
± --
See page 28
12
INTERNAL
EXTERNAL LEAD DOOR
2+1 ConfigurationSliding Left
SCALE A3 @ 1:15
Master Configuration: 3 panel (shown is 2 sliding and 1 fixed - 2+1)
Key features Fixed pane can be specified
on the left or right
All panels can slide or flexible opening
See Configuration Key for section detail
2+1
See page 09 for configurations
Master Configurations
12 19
11 1 13 18
1710
13
Inlin
e Sl
ider
182
EXTERNAL
INTERNAL
SLIDER DETAIL DRAWINGSliding Panel to Triple Frame (Jamb) Detail
44
105
FRAME COVER
FRAME INSERT COVER
LOCKSTILE
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000710
2
Sliding Panel to Triple Frame (Jamb)Detail
1 OF 1
± --
± --
SLIDER DETAIL DRAWINGFixed Interlocker to Sliding Interlocker Detail
226
20
INTERLOCKER
INTERLOCKER BEAD
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000711
2
Fixed Panel to Double Frame (Jamb)Detail
1 OF 1
± --
± --
Configuration Key
See page 14 See page 23
1 - Fixed interlocker to sliding interlocker detail
10 - Fixed panel to triple frame (bottom track) detail
See page 25 See page 30
See page 24
12 - Fixed panel to triple frame (top track) detail
17 - Sliding panel to triple frame (bottom track) detail
11 - Fixed panel to triple frame (jamb) detail
See page 31 See page 32
18 - Sliding panel to triple frame (jamb) detail
19 - Sliding panel to triple frame (top track) detail
See page 26
13 - Sliding interlocker to sliding interlocker detail
SLIDER DETAIL DRAWINGSliding Interlocker to Sliding Interlocker Detail
226
20
INTERLOCKER
INTERLOCKER BEAD
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000712
2
Sliding Interlocker toSliding InterlockerDetail
1 OF 1
± --
± --
182
44
SLIDER DETAIL DRAWINGFixed Panel to Triple Frame (Bottom Track) Detail
INTERNAL EXTERNALWEDGE GASKET
STAINLESS RUNNER
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000718
2
Fixed Panel to TripleFrame (Bottom Track)Detail
1 OF 1
± --
± --18
2
EXTERNAL
INTERNAL
SLIDER DETAIL DRAWINGFixed Panel to Triple Frame (Jamb) Detail
44
FRAME COVER
FRAME INSERT COVER
WEDGE GASKET
20 24 FRAME BEAD
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000709
2
Fixed Panel to Triple Frame (Jamb)Detail
1 OF 1
± --
± --
182
44
SLIDER DETAIL DRAWINGFixed Panel to Triple Frame (Top Track) Detail
EXTERNALINTERNAL
WEDGE GASKET
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000719
2
Fixed Panel to TripleFrame (Top Track)Detail
1 OF 1
± --
± --
SLIDER DETAIL DRAWINGSliding Panel to Triple Frame (Bottom Track) Detail
44
182
59
BOTTOM SASHSTAINLESS RUNNER
RUNNING GEAR
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000720
2
Sliding Panel to TripleFrame (Bottom Track)Detail
1 OF 1
± --
± --
SLIDER DETAIL DRAWINGSliding Panel to Triple Frame (Top Track) Detail
44
182
59
TOP SASH
ANTI-LIFT PACKER
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000721
2
Sliding Panel to TripleFrame (Top Track)Detail
1 OF 1
± --
± --
14
Technical DrawingsSLIDER DETAIL DRAWINGFixed Interlocker to Sliding Interlocker Detail
226
20
INTERLOCKER
INTERLOCKER BEAD
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000711
2
Fixed Panel to Double Frame (Jamb)Detail
1 OF 1
± --
± --
1 Fixed interlocker to sliding interlocker detail
15
Inlin
e Sl
ider
116
44
SLIDER DETAIL DRAWINGFixed Panel to Double Frame (Bottom Track) Detail
INTERNAL EXTERNALWEDGE GASKET
STAINLESS RUNNER
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000714
2
Fixed Panel to DoubleFrame (Bottom Track)Detail
1 OF 1
± --
± --
2 Fixed panel to double frame (bottom track) detail
16
3 Flush fixed interlocker to sliding shallow interlocker
FLUSH FIXED INTERLOCKER
INTERLOCKER BEAD
SHALLOW INTERLOCKER
20
151
Technical Drawings
17
Inlin
e Sl
ider
FLUSH INTERLOCKER
INTERLOCKER BEAD
SHALLOW INTERLOCKER
20
144
4 Flush interlocker to sliding shallow interlocker
18
5 Fixed shallow interlocker to sliding shallow interlocker
Technical Drawings
FIXED SHALLOW INTERLOCKER
INTERLOCKER BEAD
SHALLOW INTERLOCKER
20
186
19
Inlin
e Sl
ider
6 Sliding shallow interlocker to sliding shallow interlocker
SHALLOW INTERLOCKER
INTERLOCKER BEAD
SHALLOW INTERLOCKER
20
186
20
SLIDER DETAIL DRAWINGSliding Panel to Sliding Panel Detail
159
86
SASH REBATESLAVE DOOR
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000713
2
Sliding Panel to Sliding Panel Detail
1 OF 1
± --
± --
7 Sliding panel to sliding panel detail
Technical Drawings
21
Inlin
e Sl
ider
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000707
2
Fixed Panel to Double Frame (Jamb)Detail
1 OF 1
± --
± --
SLIDER DETAIL DRAWINGFixed Panel to Double Frame (Jamb) Detail
44
116
INTERNAL
EXTERNAL
FRAME BEAD
WEDGE GASKET
FRAME INSERT COVER
FRAME COVER
8 Fixed panel to double frame (jamb) detail
22
116
44
SLIDER DETAIL DRAWINGFixed Panel to Double Frame (Top Track) Detail
EXTERNALINTERNAL
WEDGE GASKET
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000715
2
Fixed Panel to DoubleFrame (Top Track)Detail
1 OF 1
± --
± --
9 Fixed panel to double frame (top track) detail
Technical Drawings
23
Inlin
e Sl
ider
182
44
SLIDER DETAIL DRAWINGFixed Panel to Triple Frame (Bottom Track) Detail
INTERNAL EXTERNALWEDGE GASKET
STAINLESS RUNNER
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000718
2
Fixed Panel to TripleFrame (Bottom Track)Detail
1 OF 1
± --
± --
10 Fixed panel to triple frame (bottom track) detail
24
182
EXTERNAL
INTERNAL
SLIDER DETAIL DRAWINGFixed Panel to Triple Frame (Jamb) Detail
44
FRAME COVER
FRAME INSERT COVER
WEDGE GASKET
20 24 FRAME BEAD
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000709
2
Fixed Panel to Triple Frame (Jamb)Detail
1 OF 1
± --
± --
11 Fixed panel to triple frame (jamb) detail
Technical Drawings
25
Inlin
e Sl
ider
182
44
SLIDER DETAIL DRAWINGFixed Panel to Triple Frame (Top Track) Detail
EXTERNALINTERNAL
WEDGE GASKET
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000719
2
Fixed Panel to TripleFrame (Top Track)Detail
1 OF 1
± --
± --
12 Fixed panel to triple frame (top track) detail
26
SLIDER DETAIL DRAWINGSliding Interlocker to Sliding Interlocker Detail
226
20
INTERLOCKER
INTERLOCKER BEAD
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000712
2
Sliding Interlocker toSliding InterlockerDetail
1 OF 1
± --
± --
13 Sliding interlocker to sliding interlocker detail
Technical Drawings
27
Inlin
e Sl
ider
SLIDER DETAIL DRAWINGSliding Panel to Double Frame (Bottom Track) Detail
44
BOTTOM SASH
RUNNING GEAR
116
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000716
2
Sliding Panel to DoubleFrame (Bottom Track)Detail
1 OF 1
± --
± --
14 Sliding panel to double frame (bottom track) detail
28
SLIDER DETAIL DRAWINGSliding Panel to Double Frame (Jamb) Detail
105
116
44
FRAME COVER
LOCKSTILE
BRUSH GASKET
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000708
2
Sliding Panel to Double Frame (Jamb)Detail
1 OF 1
± --
± --
15 Sliding panel to double frame (jamb) detail
Technical Drawings
29
Inlin
e Sl
ider
SLIDER DETAIL DRAWINGSliding Panel to Double Frame (Top Track) Detail
TOP SASH
ANTI-LIFT PACKER
44
116
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000717
2
Sliding Panel to DoubleFrame (Top Track)Detail
1 OF 1
± --
± --
16 Sliding panel to double frame (top track) detail
30
SLIDER DETAIL DRAWINGSliding Panel to Triple Frame (Bottom Track) Detail
44
182
59
BOTTOM SASHSTAINLESS RUNNER
RUNNING GEAR
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000720
2
Sliding Panel to TripleFrame (Bottom Track)Detail
1 OF 1
± --
± --
17 Sliding panel to triple frame (bottom track) detail
Technical Drawings
31
Inlin
e Sl
ider
182
EXTERNAL
INTERNAL
SLIDER DETAIL DRAWINGSliding Panel to Triple Frame (Jamb) Detail
44
105
FRAME COVER
FRAME INSERT COVER
LOCKSTILE
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000710
2
Sliding Panel to Triple Frame (Jamb)Detail
1 OF 1
± --
± --
18 Sliding panel to triple frame (jamb) detail
32
SLIDER DETAIL DRAWINGSliding Panel to Triple Frame (Top Track) Detail
44
182
59
TOP SASH
ANTI-LIFT PACKER
ANGULAR:
LINEAR:
2 3 41
E
D
C
B
A
F
TEL: 0845 450 6662www.origin-global.com
ALL DIMENSIONS IN mm. DO NOT SCALE.
A4SHEET SIZEPROJECTION
SHEETREVISION
DOCUMENT TYPE
APPROVED
DRAWN
SCALE
ORIGIN FRAMES LTD., Sands 10 Industrial Estate,Hillbottom Road, High Wycombe, Buckinghamshire, HP12 4HS
CHECKED
DATE
DATE
DATE
SIGNATURE
SIGNATURE
SIGNATURE
DRAWING NO.
MATERIAL
DRAWING TITLE
PART NO.
GENERAL TOLERANCETHIS DRAWING CONFORMS TO
SURFACE FINISH
BS 8888:2013
ISO 8015:2011TOLERANCING
THIS INFORMATION AND DRAWING ARE THE COPYRIGHTOF ORIGIN FRAMES LIMITED. COPYRIGHT RESERVEDBY THEM AND IS ISSUED ON THE CONDITIONTHAT IT IS NOT COPIED OR DISCLOSED BYOR TO ANY UNAUTHORISED PERSONS WITHOUTPRIOR CONSENT OF ORIGIN FRAMES LIMITED.
RK
CW
MZ
09/05/2017
09/05/2017
09/05/2017
PART DRAWING1:2
----
--
0000721
2
Sliding Panel to TripleFrame (Top Track)Detail
1 OF 1
± --
± --
19 Sliding panel to triple frame (top track) detail
Technical Drawings
33
Inlin
e Sl
ider
20 Drip bar (optional extra)
All dimensions are in mm. Do not scale.
Drip Bar (120mm) P193 0002540 1
DESCRIPTION PART No. DRAWING No. REV
120
15,5 4°
All dimensions are in mm. Do not scale.
Drip Bar (150mm) P192 0002541 1
DESCRIPTION PART No. DRAWING No. REV
150
15,5 3°
All dimensions are in mm. Do not scale.
Drip Bar (60mm) P140 0001894 2
DESCRIPTION PART No. DRAWING No. REV
15,5
60
8°
34
Installation Guide1. Prepare the opening
Measure aperture width.
Measure aperture height.
FIG 1
FIG 2
35
Inlin
e Sl
ider
Level the threshold in both directions, packing every 500mm apart for the length of the opening.
Lay frame profiles in front of
aperture, being careful not
to scratch the powder coat.
FIG 3
FIG 4
36
2. If applicable, join the top/ bottom frame profiles together
Apply suitable sealant on ends of profile and around the pre-inserted frame connectors.
FIG 5
Installation Guide
37
Inlin
e Sl
ider
Connect the frame
profiles together.
Fix the frame profiles
together and repeat for
remaining frame pieces.
FIG 6
FIG 7
38
3. Connect the jambs and bottom track
Apply suitable sealant to profile ends.
FIG 8
Installation Guide
39
Inlin
e Sl
ider
Insert alignment cleats to
the frame. If set includes a
fixed panel, one alignment
cleat is required per corner
and should be fitted in
25mm rebate.
Join jamb to
bottom track.
FIG 9
FIG 10
40
Tighten the cleat join
with a 4mm Allen Key
and screws provided.
Check join, remove excess
sealant and repeat process
for second jamb.
FIG 11
FIG 12
Installation Guide
41
Inlin
e Sl
ider
4. If applicable, connect the fixed interlocker (only applicable for sets with fixed panel)
Align fixed interlocker to pre-made notch on bottom track. Ensure profile position is as per section above.
FIG 13
42
Screw interlocker end
plate in to position with
3.9 x 25mm screws.
Use end plate as guide to drill
3mm pilot holes in frame.
Use 3.9 x 16mm screws.
FIG 14
FIG 15
Installation Guide
43
Inlin
e Sl
ider
Then unscrew and
remove end plate.
Seal screw holes with
suitable sealant.
FIG 16
FIG 17
44
Fix interlocker end plate.
Tighten screws and repeat
process for top interlocker
end plate.
FIG 18
FIG 19
Installation Guide
45
Inlin
e Sl
ider
46
5. Lift the frame in to aperture
Lift frame in to aperture,
ensuring drainage caps
are situated externally.
Insert packers above
both jambs.
FIG 20
FIG 21
Installation Guide
47
Inlin
e Sl
ider
6. Fix the bottom track
Where possible, fixing
points should be on both
sides of the frame, in a
zig-zag pattern.
Use an HSS bit to drill and countersink an
appropriate sized fixing hole through the frame.
This should be no more than 150mm from the
external corner of the frame.
Insert suitable sealant to fixing hole, then screw
preferred fixing in place. Repeat process along
the bottom track, ensuring fixings are within
900mm intervals.
FIG 22
FIG 23 FIG 24
48
7. Level and fix both jambs
Level out
jambs in both
directions.
FIG 25
FIG 26
Pack out jambs accordingly
when level.
Installation Guide
49
Inlin
e Sl
ider
Use an HSS bit to drill and
countersink an appropriate
sized fixing hole through the
frame. This should be no
more than 150mm from the
external corner of the frame.
Screw preferred fixing in
place. Repeat process along
the jambs, ensuring fixings are
within 600mm intervals.
FIG 27
FIG 28
50
8. Fix the top track
Use an HSS bit to drill and countersink an appropriate sized fixing hole through the frame. This should be no
more than 150mm from the external corner of the frame.
FIG 29
Installation Guide
51
Inlin
e Sl
ider
Insert suitable sealant to
fixing hole, then screw
preferred fixing in place. This
must be done at both ends
of the top track.
Accurately measure the
internal frame dimensions.
FIG 30
FIG 31
52
Pack out across the top track
for consistent internal frame
sizes. Ensure the track doesn’t
bow in any direction.
Use an HSS bit to drill and
countersink an appropriate
sized fixing hole through the
frame. Insert sealant to fixing
hole, then screw preferred
fixing in place. Repeat
process along the top track,
ensuring fixings are within
900mm intervals.
FIG 32
FIG 33
Installation Guide
53
Inlin
e Sl
ider
Measure diagonally from
corner to corner to check
the frame is square.
Seal the drainage isolator in
place, ensuring ends of profile
are sealed with edge of frame.
FIG 34
FIG 35
54
Insert all running gear profiles
in to necessary track channels.
Install sashes, working from inside to outside.
Level the running gear profiles
by adjusting the roller height
with a 3mm Allen Key.
FIG 36
FIG 37
9. Install the sash
Installation Guide
55
Inlin
e Sl
ider
Insert top of sash in to top
track channel.
Swing bottom of sash above
running gear.
FIG 38
FIG 39
56
Drop sash on to running gear,
ensuring the running gear sits
within the bottom of the sash.
Check to ensure bottom
of sash and running gear
components are flush at
both ends.
FIG 40
FIG 41
Installation Guide
57
Inlin
e Sl
ider
If applicable, repeat process
for remaining sashes.
FIG 42
58
Fix anti-lift blocks above each
sash corner when the sash
is in the closed position. Fix
using 3.9 x 25mm screws and
position no more than 60mm
from the external corner of
the sash.
Level the lockstile to ensure
the sash is parallel to the
frame. Repeat for all opening
sashes to ensure the
interlockers line up correctly.
FIG 43
FIG 44
Installation Guide
59
Inlin
e Sl
ider
Align centre keeps with
corresponding locking points.
(Situated directly above and
below handle).
Working from bottom to
top, adjust keep positions
if necessary. Keeps can be
packed out using the 0.5
and 2mm packers supplied.
Adjust keeps until the
handle engages correctly,
and the key in the lock
cylinder turns smoothly.
FIG 45
FIG 46
60
If more adjustment is required,
use a 3mm Allen Key to adjust
the locking point.
FIG 47
Installation Guide
61
Inlin
e Sl
ider
10. If applicable, install the fixed panel
Pack out as appropriate.
Apply supplied structural
sealant around each packer.
FIG 48
FIG 49
62
Place 10mm anti-lift packers
in to track channel.
Insert glass into frame
and slide over on to pre-
applied structural sealant in
interlocker. Pack out below
glass so is central in the frame.
FIG 50
FIG 51
Installation Guide
63
Inlin
e Sl
ider
Use a straight edge or
long level along the fixed
interlocker to ensure
straightness. Pack out
accordingly between edge of
glass and jamb.
Secure frame bead in place.
First clip top and bottom of
bead, then proceed to clip in
the centre.
FIG 52
FIG 53
64
Fit wedge gasket between
glass and outer frame, on both
inside and outside glass faces.
Apply bead of structural
sealant along the length of
interlocker (both inside and
outside faces). Leave to fully
cure before operating the set.
FIG 54
FIG 55
Installation Guide
65
Inlin
e Sl
ider
11. Install frame covers
Clip in the vertical frame
cover pieces.
Clip in the horizontal frame
cover pieces.
FIG 56
FIG 57
66
Notes
67
Inlin
e Sl
ider
OFDL_18.3.3
Origin Global HQ, Stuart House,Castle Estate, Coronation Road,Cressex Business Park, High Wycombe,Buckinghamshire, HP12 3TA
t 0808 168 5816e enquiry@origin-global.comw www.origin-global.com
Origin Northern Centre of Excellence,Taurus Park, Europa Boulevard, Westbrook, Warrington, Cheshire, WA5 7ZT
t 01925 907 907e enquiry@origin-global.com w www.origin-global.com
Contact
Accounts
t 08448 802 371 or 01494 416 895 e Finance@origin-global.com
Marketing
t 08448 802 374 or 01494 416 897 e Marketing@origin-global.com
Sales Operations
t 0808 168 5816 or 01494 686 868 e OrdersNorth@origin-global.com
e OrdersSouth@origin-global.com
Solutions
t 08448 802 373 or 01494 416 896 e Solutions@origin-global.com
Fleet and Logistics
t 08448 802 378 or 01494 416 898 e Logistics@origin-global.com