Post on 16-Mar-2020
transcript
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2017 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
FENDER FLARESP/N 08P21-T6Z-100served. AII06945-14 (170
2018 RIDGELINE
7) 0
Issue Date
JUL 2017
PARTS LISTRight front bumper flare
Left front bumper flare
Right front fender flare
Left front fender flare
Right rear bumper flare
Left rear bumper flare
Right rear fender flare
Left rear fender flare
8 Clips
4 Snap fit clips
6 Alcohol swabs
2 Self-tapping screws, 5 x 14 mm
2 Self-tapping screws, 5 x 20 mm
1 of 168P21-T6Z-1000-90
2 Washers
2 Spring nuts
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriverStubby Phillips screwdriverFlat-tip screwdriverRatchet10 mm Socket10 mm Open end wrenchBlanketShop towelPushpinDrill3 mm, 5 mm, 6 mm, 8 mm, and 10 mm Drill bitsEye protection (face shield, safety goggles, etc.)FileUtility knifeMasking tape TapeThe following tools are available through the Honda Tool and Equipment Program. On the iN, click on: Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.• Trim Tool Set (T/N SOJATP2014)• Air Saw (T/N AT192A)
2 of 16 AII06945-1
Illustration of the Fender Flares on the Vehicle
RIGHT FRONT FENDER FLARE
RIGHT REAR FENDER FLARE
RIGHT REAR BUMPER FLARE
RIGHT FRONT BUMPER FLARE
LEFT FRONT BUMPER FLARE
LEFT FRONT FENDER FLARE
LEFT REAR FENDER FLARE
LEFT REAR BUMPER FLARE
4 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
INSTALLATION
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1. Disconnect the negative cable from the battery:• Wrap a shop towel around the hood latch.
HOOD LATCH(Wrap with a shop towel.)
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06945-1
• Remove the front bulkhead cover.
FRONT BULKHEAD COVER
10 CLIPS
• Remove the intake air tube.• Disconnect the negative cable from the battery.
INTAKE AIR TUBE2 CLIPS
4 (1707) 3 of 16
2. Remove the three self-tapping screws from the left front wheel arch protector.
LEFT FRONT WHEEL ARCH PROTECTOR
3 SELF-TAPPING SCREWS
3. Remove the left front wheel arch protector.
6 CLIPS
LEFT FRONT WHEEL ARCH PROTECTOR
2 RETAINING TABS
2 CLIPS(FRONT SIDE) CLIP
(REAR SIDE)
RETAINING TAB
4. Repeat steps 2 and 3 on the right side of the vehicle.
4 of 16 AII06945-1
5. Remove the front bumper:• Using a flat-tip screwdriver, remove the H
emblem from the front grille.
H EMBLEM
FRONT GRILLE4 CLIPS
H EMBLEM2 RETAINING TABS
FRONT
FLAT-TIP SCREWDRIVER
FRONT CENTER UPPER BEAM
4 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
• Remove the front upper grille.
4 RETAINING TABS
FRONT UPPER GRILLE
4 BOLTS
12 CLIPS
• Apply masking tape on each side as shown.
FRONT BUMPER
HEADLIGHT
FRONT FENDER
MASKING TAPE
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06945-1
• Remove the four self-tapping screws, eight clips, four washer-bolts, and four flange bolts.
4 SELF-TAPPING SCREWS
4 CLIPS 2 WASHER-BOLTS
4 FLANGE BOLTS
2 WASHER-BOLTS
BOTTOM VIEW
2 WASHER-BOLTS
2 WASHER-BOLTS
2 CLIPS 2 CLIPS
4 CLIPS
4 FLANGE BOLTS
4 (1707) 5 of 16
• With the help of an assistant, release the seven retaining tabs on each side.
3 RETAINING TABS
FRONT BUMPER
4 RETAINING TABS
FRONT BUMPER
FRONT BUMPER
6 of 16 AII06945-1
• Release the front grille.
2 RETAINING TABS
FRONT GRILLE
FLAT-TIP SCREWDRIVER
2 RETAINING TABS
FRONT GRILLE
FRONT GRILLE
FRONT GRILLEHEADLIGHT
4 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
• With the help of an assistant, remove the front bumper and unplug the vehicle connectors.
• Place the front bumper on a blanket.
FRONT BUMPER
VEHICLE CONNECTOR
VEHICLE CONNECTOR(if equipped)
6. Remove the seven clips from the left front wheel arch protector.
6 CLIPS
CLIP
LEFT FRONT WHEEL ARCH PROTECTOR(Do not reuse.)
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06945-1
7. Install the seven clips removed in step 6 to the left front fender flare.
6 CLIPS
LEFT FRONT FENDER FLARE
CLIPSPRING NUT
8. Install one spring nut to the left front fender flare as shown. NOTE: Make sure to install the spring nut in the correct orientation.
9. Attach a piece of masking tape to the end of the adhesive backings as shown. Peel back the adhesive backings partway and temporarily attach them to the front surface of the left front fender flare.
MASKING TAPE
Temporarily attach.
11 ADHESIVE BACKINGS(Peel.)
LEFT FRONT FENDER FLARE
4 (1707) 7 of 16
10. Using one alcohol swab, thoroughly clean the area where the left front fender flare will attach.
LEFT FRONT FENDER
ALCOHOL SWAB
Clean with an alcohol swab.
11. Install the left front fender flare to the left front fender.
LEFT FRONT FENDER FLARE
7 CLIPS
2 RETAINING TABS
8 of 16 AII06945-1
12. Secure the left front fender flare to the left front fender with the two self-tapping screws removed in step 2.
RUBBER MOLDING(Make sure it is not twisted or rolled under the flare.)
11 ADHESIVE BACKINGS(Remove.)
LEFT FRONT FENDER FLARE
2 SELF-TAPPING SCREWS
SECTION VIEW
LEFT FRONT FENDER FLARE
FRONT FENDER
13. While applying light pressure against the left front fender flare, carefully remove the taped adhesive backings.
14. Using the palm of your hand, firmly press the left front fender flare against the left front fender.
4 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
15. Using a utility knife, cut off the left front inner fender where the left front fender flare is interfering as shown.
LEFT FRONT FENDER FLARE
LEFT FRONT INNER FENDER
Cut off.
LEFT FRONT INNER FENDER LEFT FRONT
FENDER FLARECUTTING AREA
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06945-1
16. Secure the left front fender flare to the vehicle bracket with the self-tapping screw removed from the front bumper.
SELF-TAPPING SCREW(Removed from the front bumper.)
LEFT FRONT FENDER FLARE
VEHICLE BRACKET
17. Repeat steps 6 through 16 on the right side of the vehicle to install the right front fender flare.
18. Using a pushpin, pierce the five scribe marks on the front bumper. NOTE: Make sure to pierce perpendicular to the front bumper.
: 5 MARKS
5 SCRIBE MARKS FRONT
BUMPER
PUSHPIN(Pierce perpendicular.)
FRONT BUMPER(inside)
4 (1707) 9 of 16
19. While wearing eye protection, drill the four pierced marks on the front bumper to 10 mm. Drill first with a 3 mm drill bit. Next, drill with a 6 mm drill bit and an 8 mm drill bit. Then, finish with a 10 mm drill bit. Remove any burrs.NOTE: Make sure to drill perpendicular to the front bumper.
: 4 MARKS
FRONT BUMPER
DRILL(Drill perpendicular.)
3 mm 6 mm 8 mm 10 mm DRILL BITS
FRONT BUMPER(outside)
: MARK
DRILL(Drill perpendicular.)
3 mm 5 mm DRILL BITS
FRONT BUMPER
20. While wearing eye protection, drill one pierced mark to 5 mm. Drill first with a 3 mm drill bit, then finish with a 5 mm drill bit. Remove any burrs.NOTE: Make sure to drill perpendicular to the front bumper.
10 of 16 AII06945-1
21. While wearing eye protection, cut off the front bumper along the scribe line with an air saw. Remove any burrs.
FRONT BUMPER
Cut off.
AIR SAW
CUTTING AREA
FRONT BUMPER
SCRIBE LINE
22. Repeat steps 18 through 21 on the right side of the front bumper.
23. With the help of an assistant, temporarily install the front bumper. Do not secure the left and right front inner fenders in this step.
FRONT BUMPER
4 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
24. Install the two snap fit clips to the left front bumper flare.
2 SNAP FIT CLIPS
LEFT FRONT BUMPER FLARE
25. Attach a piece of masking tape to the end of the adhesive backings as shown. Peel back the adhesive backings partway and temporarily attach them to the front surface of the left front bumper flare.
MASKING TAPE
Temporarily attach.
4 ADHESIVE BACKINGS(Peel.)
LEFT FRONT BUMPER FLARE
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06945-1
26. Using one alcohol swab, thoroughly clean the area where the left front bumper flare will attach.
FRONT BUMPER
ALCOHOL SWAB
Clean with an alcohol swab.
27. Install the left front bumper flare to the front bumper with the two snap fit clips.
LEFT FRONT BUMPER
LEFT FRONT BUMPER FLARE
2 SNAP FIT CLIPS
4 (1707) 11 of 16
28. Pull back the left front inner fender. Secure the left front bumper flare to the front bumper with the four clips. NOTE: Do not push the clip too tightly, or it may deform the left front bumper flare. Adjust the clip, as necessary.
4 CLIPSLEFT FRONT BUMPER FLARE
WASHER
LEFT FRONT INNER FENDER(Pull back.)
5 x 14 mm SELF-TAPPING SCREW(supplied)
29. Secure the left front bumper flare to the front bumper with one washer and one 5 x 14 mm self-tapping screw.
12 of 16 AII06945-1
30. Secure the left front bumper flare to the front bumper with one 5 x 20 mm self-tapping screw and one self-tapping screw removed in step 2. Reinstall one self-tapping screw to the front bumper.
LEFT FRONT BUMPER FLARE
5 x 20 mm SELF-TAPPING SCREW(supplied)
2 SELF-TAPPING SCREWS
RUBBER MOLDING(Make sure it is not twisted or rolled under the flare.)
SECTION VIEW
LEFT FRONT BUMPER FLARE
FRONT BUMPER
31. While applying light pressure against the left front bumper flare, carefully remove the taped adhesive backings.
32. Using the palm of your hand, firmly press the left front bumper flare against the front bumper.
33. Repeat steps 24 through 32 on the right side of the vehicle to install the right front bumper flare.
4 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
34. Remove the seven self-tapping screws from the left rear wheel arch protector.
LEFT REAR WHEEL ARCH PROTECTOR
7 SELF-TAPPING SCREWS
35. Remove the left rear wheel arch protector.
LEFT REAR WHEEL ARCH PROTECTOR
RETAINING TAB
9 CLIPS
3 RETAINING TABS
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06945-1
36. Remove the nine clips from the left rear wheel arch protector.
LEFT REAR WHEEL ARCH PROTECTOR(Do not reuse.)
9 CLIPS
37. Install the nine clips removed in step 36 to the left rear fender flare.
LEFT REAR FENDER FLARE
9 CLIPS
4 (1707) 13 of 16
38. Attach a piece of masking tape to the end of the adhesive backings as shown. Peel back the adhesive backings partway and temporarily attach them to the front surface of the left rear fender flare. Remove the remaining adhesive backings.
LEFT REAR FENDER FLARE
14 ADHESIVE BACKINGS(Peel.)
6 ADHESIVE BACKINGS(Remove.)
MASKING TAPE
Temporarily attach.
RIGHT REAR FENDER FLARE
15 ADHESIVE BACKINGS(Peel.)
4 ADHESIVE BACKINGS(Remove.)
MASKING TAPE
Temporarily attach.
14 of 16 AII06945-1
39. Using one alcohol swab, thoroughly clean the area where the left rear fender flare will attach.
LEFT REAR FENDER
Clean with an alcohol swab.
ALCOHOL SWAB
40. Install the left rear fender flare to the left rear fender.
RETAINING TAB
LEFT REAR FENDER FLARE
3 RETAINING TABS
9 CLIPS
4 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
41. Secure the left rear fender flare to the left rear fender with the five self-tapping screws removed in step 34.
14 ADHESIVE BACKING(Remove.)
LEFT REAR FENDER FLARE
5 SELF-TAPPING SCREWS
RUBBER MOLDING(Make sure it is not twisted or rolled under the flare.)
SECTION VIEW
LEFT REAR FENDER FLARE
REAR FENDER
42. While applying light pressure against the left rear fender flare, carefully remove the taped adhesive backings.
43. Using the palm of your hand, firmly press the left rear fender flare against the left rear fender.
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06945-1
44. Align the hook on the left rear bumper flare with the holder on the left rear fender flare, then slide the left rear bumper flare rearward into place.
LEFT REAR FENDER FLARE HOOK
LEFT REAR FENDER FLARE
LEFT REAR BUMPER FLARE
LEFT REAR BUMPER FLARE
FRONT
4 (1707) 15 of 16
45. Secure the left rear bumper flare to the rear bumper with the two remaining self-tapping screws removed in step 34.
2 SELF-TAPPING SCREWS
LEFT REAR BUMPER FLARE
RUBBER MOLDING(Make sure it is not twisted or rolled under the flare.)
SECTION VIEW
LEFT REAR BUMPER FLARE
REAR BUMPER
46. Repeat steps 34 through 45 on the right side of the vehicle to install the right rear fender flare and the right rear bumper flare.
47. Install all removed parts except for the front bulkhead cover and the intake air tube.
48. Check that all wire harnesses are routed properly and all connectors are plugged in.
49. Connect the negative cable to the battery.50. Install the front bulkhead cover and the intake air
tube.51. Press and hold the audio unit power button for 2
seconds to restore the audio and navi (if equipped) system functions.
52. Set the clock on vehicles without navigation.53. If necessary, restore the systems back to normal
operation as described in the service information.
16 of 16 AII06945-1
MAINTENANCE
Removing the Rear Bumper
• If you remove the rear bumper, remove the left and right rear bumper flares to access the screws that fasten the rear bumper.
LEFT REAR FENDER FLARE
REAR BUMPER
LEFT REAR FENDER FLARE
SCREW
REAR BUMPER
4 (1707) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.