Post on 18-Mar-2020
transcript
www.ritek.net.au 1300 929 782
An insulated roof panel with a ceiling
like finish. With great spanning
capabilities, a Trimdek top sheet
profile and a flat underside.
Insulated Flat Underside
Roof System
Trimdek® Top Profile
Trimdek is a registered trademark of Bluescope Steel Limited.
10 Year Warranty
www.ritek.net.au 1300 929 782
An insulated Trimdek® roof
panel with a flat underside
Insulated Roof Panel Design
Smartline Trimdek® is a combination of roofing,
insulation and ceiling in one durable, functional and
attractive panel. This all-in-one roofing solution has
exciting design possibilities and countless benefits for
your outdoor living area. Smartline Trimdek® will
improve your lifestyle and add value to your home
with the least amount of effort.
Smartline Trimdek Colour Options
The Trimdek® Smartline topside roof panel comes in
a selection of colours to suit your design. Please
refer to the colour selection chart.
Panel Coverage
1000mm wide coverage
High Comfort
Climate comfort is achieved with Smartline
Trimdek® with a 3 layered system, with insulation
wrapped in Colorbond® steel.
Roofing Layer
The Smartline Trimdek® roofing layer is made
from Hi-Tensile Bluescope Colorbond® steel for
strength and durability in a range of thermally
efficient and modern colours.
Insulation Layer
The Smartline Trimdek® insulation layer is a high
performance insulating polystyrene core available
in various thicknesses 50, 75, 100, 125 and 150mm for
longer spans and varying thermal performance. Each
panel core incorporates a service duct suitable for
electrical cabling for ceiling lights and fans.
Ceiling Layer
The Smartline Trimdek® ceiling layer is
made from proven Bluescope
Colorbond® steel, available in two
finishes coloured Surfmist® (off white) or
Classic Cream®.
Trimdek ®
, Colorbond®
, Surfmist®
& Classic Cream®
are registered trademarks of Bluescope Steel Limited.
Panel Thickness Options
Smartline Trimdek® insulation layer is a high
performance insulating polystyrene.
50mm 125mm
75mm 150mm
100mm
Smartline Trimdek® - 3 Layered Roofing System
R-Values
50 75 100 125 150 Panel Thickness
1.6 2.3 2.9 3.6 4.2 R Value at 8°C (m2k/W)
1.6 2.2 2.8 3.5 4.1 R Value at 20°C (m2k/W)
Bottom Sheet Profiles
The Smartline Trimdek® panel features a polystyrene core that
is permanently bonded to a smooth, easy to clean Colorbond®
steel underside and topside.
Ceiling finishes are designed to be
low maintenance and unobtrusive.
Each of the Plain and Elegance
ceiling finishes will complement
any outdoor entertaining area.
Smartline Trimdek Benefits
Blocks Heat - provides efficient, long lasting
insulation and comfort.
Saves Money, Adds Value - the simple, quick
modular design reduces build time and therefore cost.
Deadens Noise - the solid polystyrene core helps
to reduce noise from rain and hail.
Low Maintenance - Colorbond® steel roof and ceiling
gives a long-lasting, easy to clean finish.
Simple Construction - No rafters and battens are
required.
Strong and Durable - Two layers of steel laminated to
solid polystyrene core provides strength and durability.
Always Comfortable - Day or night, winter or summer,
be comfortable all year round.
Top Sheet Colour
Selection Chart
Please Note: Minor variations in colour can occur and characteristics of the raw material used. Colour fading may occur over time. Colours shown on
this chart may vary due to the printing process. Accurate colour samples are available through a Ritek representative if required.
enquiries@ritek.net.au 1300 929 782
Smartline Plain Profile
Smartline Elegance Profile
Dune® Headland® Pale
Eucalypt® Shale Grey® Paperbark® Surfmist® Classic
Cream™
Smartline Trimdek® colour range has been
rigorously tested and hand picked with
the support of Bluescope Steel to offer
top side roofing colours with the best
thermal performance and made tough for
Australian conditions.
Trimdek ®
, Colorbond®
, Surfmist®
& Classic Cream®
are registered trademarks of Bluescope Steel Limited. All colours specified above are registered trademarks of Bluescope Steel Limited.
www.ritek.net.au 1300 929 782
Whether you are selecting Smartline Trimdek® panel for cyclonic or non cyclonic locations,
the tables below make selecting the right span and panel thickness easy.
Smartline Trimdek Benefits
Non-Cyclonic
Panel Thickness
50mm 75mm 100mm 125mm 150mm
Wind
Class
ULS De-sign Wind Pressure
(kPa)
Max Span (m) Max
Canti-lever
(mm)
Max Span (m) Max
Canti-lever
(mm)
Max Span (m) Max
Canti-lever
(mm)
Max Span (m) Max
Canti-lever
(mm)
Max Span (m) Max
Canti-lever
(mm)
Single
Span
Multi-
span
Single
Span
Multi-
span
Single
Span
Multi-
span
Single
Span
Multi-
span
Single
Span
Multi-
span
N2 1.51 3.9 3.6 550 4.5 5.1 900 5.1 6.0 1200 5.7 6.6 1600 6.0 7.2 2400
N3 2.35 3.0 2.7 550 3.6 3.9 900 3.9 4.8 1200 4.5 5.1 1600 4.8 5.1 1900
N4 3.50 2.1 1.8 550 2.7 2.4 900 3.3 3.3 1200 3.6 3.3 1400 3.9 3.3 1500
N5 5.17 1.5 550 2.1 1.5 800 2.7 2.1 900 3.0 2.1 900 3.0 2.1 900
Cyclonic
Panel Thickness
50mm 75mm 100mm 125mm 150mm
Wind
Class
ULS Design Wind Pres-
sure (kPa)
Max Span (m) Max
Canti-lever
(mm)
Max Span (m) Max
Canti-lever
(mm)
Max Span (m) Max
Canti-lever
(mm)
Max Span (m) Max
Canti-lever
(mm)
Max Span (m) Max
Canti-lever
(mm)
Single
Span
Multi-
span
Single
Span
Multi-
span
Single
Span
Multi-
span
Single
Span
Multi-
span
Single
Span
Multi-
span
C1 3.42 2.1 1.8 550 3.0 2.1 900 3.3 2.7 1200 3.6 3.3 1600 3.9 3.6 1800
C2 5.08 1.5 550 2.1 1.5 800 2.7 2.1 1000 3.0 2.4 1200 3.3 3.0 1300
C3 7.51 1.8 1.5 700 2.1 1.5 800 2.7 1.5 1000
C4 10.12 1.5 600 2.1 600