Post on 03-Dec-2018
transcript
1SPECIFICATIONS AND DRAWINGS ARE SUBJECT TO ALTERATION WITHOUT PRIOR NOTICE - DIMENSIONS IN MILLIMETER
ENGINEERED TO CONNECT
INTERNAL CONNECTORS FOR FFC AND FPC
2 SPECIFICATIONS AND DRAWINGS ARE SUBJECT TO ALTERATION WITHOUT PRIOR NOTICE - DIMENSIONS IN MILLIMETER
BOARD-TO-CABLE CONNECTIONS FOR FFC AND FPC
Board to cable connections for FFC and FPC are the one of the most important way to transfer data.
Yamaichi is offering a wide range of these connector solutions. ZIF-Connectors as well as non-ZIF connectors are available. The most of the offered connectors are able to transmit High Speed Signals up to 10Gbps and are fulfilling the special requirements for all the new High Speed applications which are based on the different new Input/Output standards like the USB 3.1.
Besides the connectors Yamaichi is supplying also the fitting cables, like standard FFC, High Speed FFC and YFlex, a special High Speed FPC, for highest transmission rates in perfect quality.
APPLICATIONS:
Our ZIF/non-ZIF connectors and cable systems are tested and used for a high variety of applications.
- Automotive e.g. infotainment systems, camera systems, steering systems
- Medical
- Industrial
- Consumer electronics
Connector Pitch (mm)
PositionShielding Locking
FunctionHigh Speed Trasmission
Applicable Cable Type
90° 180° FFC HS FFC YFLEX
Y-Lock 0.5 - 1.0 x x no x x
FPC Series 0.5 - 1.0 x x no x
HF507S 0.5 x x posssible x x x x
HF509S 0.5 x posssible x x x x
HF513S 0.5 posssible x x x x
HF601 0.5 x x no x x x x x
Overview of connector systems and possible cable solutions
3SPECIFICATIONS AND DRAWINGS ARE SUBJECT TO ALTERATION WITHOUT PRIOR NOTICE - DIMENSIONS IN MILLIMETER
Ordering code for FFC cableYamaichi is offering the complete system including the FFC. For the second generation the stiffener is already assembled.
Y-LPF - F x - xx - xxx -x x - F - V
Series F = FFC Pitch1 = 1.0mm5 = 0.5mm
Pin Count 12 to 30/50
Tota
l Len
gth
in
mm
Direction Supporting Tape A = sameB = opposite
Additional Stiffener 0 = one cable side 2 = two sides
Plating Termination Area F = Au Flash
UL No.
V = UL20706
FFC
(GEN2 version only)
(with other mating design)
(depending on the pitch)
Locking function between the supporting tape on the FFC and the connector. Small hooks on the inner housing of the connector insulator ensures the locking function between the FFC and connector.
SPECIAL FEATURES • Non-ZIF Board-to-Cable system• FFC has just to be pushed in (push-lock) and can be pulled out (pullforce) without any further action • Various pin counts available• Automatic assembly of FFC is possible
Y-LOCK GEN1
Y-LOCK GEN2Additional stiffener is assembled mechanically on the FFC. Locking function between stiffener and connector. Poka-Yoke system means it is not possible to insert the FFC in wrong direction. The use of the stiffener is guiding the FFC during insertion.
NON-ZIF CONNECTORS
Series No.
Connector
Pitch: 5 = 0.50mm
Pin Count: 18 and 50 (other pin counts on request)
Terminal Style: S = SMT
Orientation: 1 = 180° (90° available on request)
Plating: Mating / Termination Area BF = 0.3µm Au / Flash Au
Tape and Reel with Pick and Place (800 pcs./reel)
Y-LPF - C 5 - ** - S 1 - BF - REDC
Y-LPF - C * - 12 - S * - BF - R
Series No.
Connector
Pitch: 1 = 1.00mm 5 = 0.50mm1)
Pin Count: 12 to 30
Terminal Style: S = SMT
Orientation: 1 = 180° 9 = 90°
Plating: Mating / Termination Area BF = 0.3µm Au / Flash Au
Tape and Reel with Pick & Place Cap
The Y-Lock connector family is combining a space saving and process securing design with smart and reliable technology. The connector system is designed for applications with tough requirements. Available now in two different generations the Y-Lock is able to fulfill a large spectrum of tasks in regard to mechanical, climatic and electrical specifications.
Y-LOCK® PULLFORCE SERIES
Y-Lock GEN1 Y-Lock GEN2
1) 0.50mm pitch available with 30 pins
• Quick and easy assembly• Poka-Yoke system• Pitches: 0.5 and 1.0mm• 90° and 180° versions • Production site TS16949 certified• RoHS2011/65/EU
AUTOMOTIVE
COMPLIANT
AUTOMOTIVE
COMPLIANT
4 SPECIFICATIONS AND DRAWINGS ARE SUBJECT TO ALTERATION WITHOUT PRIOR NOTICE - DIMENSIONS IN MILLIMETER
FEATURES OF HF507S • Up to 5Gbps transmission rate• Locking mechanism• Auto vacuum mounting capability • Differential impedance: 100Ω• Suitable for LVDS, HDMI, DVI, PCI express and S-ATA data transmission • RoHS2011/65/EU
FEATURES • Same features as HF507S standard type• Locking function through special direct mating mechanism • RoHS2011/65/EU
GENERAL INFORMATION • Pin count: 21, 31, 41, 51 pins• With and without shielding (except pins 21 & 31 in 180° version)• Pitch: 0.5mm • Direction: 90° and 180°
GENERAL INFORMATION • Pin count: 41, 51 pins• Shielded version• Pitch: 0.5mm • Direction: 90°
Locking mechanism on both sides provides easy operation.Prevents cable angular insertion and guarantees secure locking
HF507S SERIES
HF507S**72 SERIES - DIRECT MATING
NON-ZIF CONNECTORS
HF507S - ** - **
HF507S - ** - 72
Series No.
No. of Contacts 21, 31, 41 and 51
02 = 180° without Shielding 04 = 90° with Shielding1)
Series No.
No. of Contacts 41 and 51
Design No.
CABLES TO BE USED:
• YFLEX customised cable (refer to page 6)• High Speed FFC with adapter • High Speed FFC direct mating type without adapter
1) 180°with shieldingnot available for 21 and 31 pin versions
5SPECIFICATIONS AND DRAWINGS ARE SUBJECT TO ALTERATION WITHOUT PRIOR NOTICE - DIMENSIONS IN MILLIMETER
NON-ZIF CONNECTORS
The new connector series is a very low profile connector with High speed transmission rates up to 10Gbps. It is a direct mating type, the locking function ensures a reliable position of the cable with the connector. The HF513 series is available with or without shielding and ground contacts.
HF513 SERIES
FEATURES • Up to 10Gbps data transfer rate (if used with YFlex cable)• Direcrect mating type. For releasing only button on connector has to be pressed • Push in locking (for releasing the button has to pressed) • With and without additional shielding pins • RoHS2011/65/EU
GENERAL INFORMATION • Pin count: 10 pins • Pitch: 0.5mm • Direction: 90°
FEATURES • Impedance matching design• Non-ZIF type with function to avoid mis-operation such as cable being diagonally inserted or cable coming off• EMI reinforced design with connecting between metal shell of adapter and metal shell of receptacle • For IEEE1394, LVDS, TMDS, S-ATA, PCI-Express applications • RoHS2011/65/EU
HF509 SERIES
HF513 - ** - Y*
HF513 - 10 - 03
Series No.
Pin Counts = 30, 40 and 50
Y0 = No Additional GND Contact for Shielding Y1 = Additional GND Contact for Shielding
Series No.
Pin Counts =10
Design No.
• High Speed FFC
CABLES TO BE USED:
• YFLEX customised cable (refer to page 6)
CABLES TO BE USED:
• YFLEX customised cable (refer to page 6)
GENERAL INFORMATION • Pin count: 30, 40 and 50 pins • Pitch: 0.5mm • Direction: 90° • Other versions on request
6 SPECIFICATIONS AND DRAWINGS ARE SUBJECT TO ALTERATION WITHOUT PRIOR NOTICE - DIMENSIONS IN MILLIMETER
The HF601 ZIF series is a very smart connector family. It combines very small design with highly sophisticated technical features. The standard version is able to transmit up to 1Gbps, the high speed version up to 5Gbps. The connector can be used with FFC with ears for an improved locking function.
The FPC Series is a tray type ZIF connector with 0.5mm and 1.0mm pitch with a high amount of possible different pin counts
HF601 SERIES
FEATURES • High speed function 1Gbps• Single types can transmit up to 5Gbps• FFC with or without ears for additional locking • Various pin counts in 90° and 180° • RoHS2011/65/EU
FEATURES• Bottom and top contacts• RoHS2011/65/EU
FPC SERIES
ZIF CONNECTORS
1) HF601 - 22 - 03
Series No.
Pin Count = 22
Design No.
2) HF601 - ** - 02
3) HF601 - ** - 12
Series No.
Pin Counts: 10, 20, 30, 40, 45, 50 and 60
02 = 90° Type
Series No.
Pin Count: 30, 40, 45 and 50
12 = 180° Type
1) 22 Pin type (up to 5Gbps) 2) 90° Type (up to 1Gbps) 3) 180° Type (up to 1Gbps)
FC - P0.5 - C* - 21 -32 - A - 4 - L - *
Series No.
Pitch: P0.5 = 0.5mm P1.0 = 1.0mm
Conductor Cross-section (Thickness x Width) C1 = 0.05 x 0.65mm (P= 1.00mm) C6 = 0.035 x 0.3mm (P= 0.50mm)
Number of Conductors
Insulation Length in mm (= Complete length minus 2 x strip length)
Cable Type / Styles (see drawing below)
Length of Stripped Conductor in mm (dimension S)
Plating: L = Tin C = Au Flash
UL Styles: No Mark = UL2896 V = UL20706
GENERAL INFORMATION • Pin count: 10 to 60 depending on type• Pitch: 0.5mm • Direction: 90° and 180°
CABLES TO BE USED:• Standard FFC
• Standard FFC • High Speed FFC
CABLES TO BE USED:
• YFLEX customised cable (refer to page 6)
GENERAL INFORMATION • Pin count: 10 to 60 depending on type• Pitch: 0.5mm • Direction: 90° and 180°
7SPECIFICATIONS AND DRAWINGS ARE SUBJECT TO ALTERATION WITHOUT PRIOR NOTICE - DIMENSIONS IN MILLIMETER
Our different ZIF/Non-ZIF connectors are able to be used with standard FFC, High Speed FFC or YFLEX (High Speed FPC). The usage of the different cables is depending on the transfer rate. Standard FFC can transfer up to 480Mbps, High Speed FFC’s can transfer up to 3Gbps and YFLEX is able to transfer up to 10Gbps.
YFLEX - HIGH SPEED FPC
STRUCTURE TO ACHIEVE HIGH SPEED TRANSMISSION
YFLEX - FPC
GND GNDSignal Signal
Copper Film Ground Bump
YFLEX SERIES
DIFFERENCE BETWEEN YFLEX & STANDARD FPCSTANDARD POLYIMIDE - FPC
FEATURES
• Available to transmit high speed up to 10Gbps with low loss• Effective to use at harshest temperature, humidity and EMI condition • Customized depending on the layout and requirement• Stable differential impedance of 100 Ohm (+/- 10%)
LCP achieves the transmission with a low dielectric loss
GND and copper film ground are connected with silver bumps which also protectfrom EMI
1. Polyimide-Copper laminating
2. Drilling
CopperBumps
Copper
Copper
LCP
Polyimide
Copper
3. Plating
3. Etching
1. Conductive Bump Printing
2. Set-up
3. Heat Press
4. Etching
8 SPECIFICATIONS AND DRAWINGS ARE SUBJECT TO ALTERATION WITHOUT PRIOR NOTICE - DIMENSIONS IN MILLIMETER
YAMAICHI ELEC TRONICSItalia s.r.l.Centro Direzionale ColleoniVia Colleoni, 1Palazzo Taurus Ing. 120864 Agrate Brianza (MB)Italy
Phone +39 039 6881-185Fax +39 039 6892-150 E-Mail sales@yamaichi.itWeb www.yamaichi.eu
YAMAICHI ELEC TRONICS GB Ltd.6 The ClockhouseStratton Park Micheldever Hampshire SO21 3DP Great Britain
Phone +44 (0)7808 493377Fax +44 (0)1962 774902E-Mail sales@yamaichi.co.ukWeb www.yamaichi.eu
YAMAICHI ELEC TRONICS Deutschland GmbHConcor Park Bahnhofstraße 20 85609 Aschheim-Dornach Germany
Phone +49 (0)89 45109 - 0Fax +49 (0)89 45109 - 110 E-Mail info@yamaichi.deWeb www.yamaichi.eu Version Sept. 2016